CM-FACILITY-MIB

TEXTUAL-CONVENTION

Types of ACL no match disposition.

TEXTUAL-CONVENTION

Describes the acl rule operation.

TEXTUAL-CONVENTION

A Network Element level Frame Rate Bandwidth Profile Mode shall be supported which will indicate if the CIR/EIR is interpreted as Information Rate (IR) or Line Rate (LR). In IR mode BWP is enforced based on number of bytes beginning with DA and ending with FCS as it was received at a port which is called the Service Frame in MEF terminology. In LR mode the BWP is enforced based on the whole frame including IFG, Preamble and SFD.

TEXTUAL-CONVENTION

.

TEXTUAL-CONVENTION

Enumerations for Bits Frame Format. none, t1-sf, t1-esf, e1-unframed, e1-crc4, e1-dualframe.

TEXTUAL-CONVENTION

Describes the impedance mode of the BITS-IN and BITS-OUT interfaces: 120OHM.

TEXTUAL-CONVENTION

Enumerations for BITS Line Code. none, t1-b8zs, t1-ami, e1-hdb3, e1-ami.

TEXTUAL-CONVENTION

Enumerations for BITS Line Type. It can be t1, e1, 2048kHz, other.

TEXTUAL-CONVENTION

Enumerations for BITS Port Type. bits-in, bits-out.

TEXTUAL-CONVENTION

Port states for CC group entities.

TEXTUAL-CONVENTION

CC port duty cycle

TEXTUAL-CONVENTION

Channel Type.

TEXTUAL-CONVENTION

This object is defined to set traffic acl resource allocation. Supported actions are: all-bk-l2 (1) - all bank allocated to l2. all-bk-l2-ipv4(2) - all bank allocated to l2/ipv4. two-bk-l2-ipv4(3) - two thirds allocated to l2/ipv4, the left belongs to ipv6. one-bk-l2-ipv4(4) - one thirds allocated to l2/ipv4, the left belongs to ipv6. none-bk-l2-ipv4(5) - all bank allocated to ipv6.

TEXTUAL-CONVENTION

Remote Link Ids used to match for Link Loss Forwarding.

TEXTUAL-CONVENTION

Describes the Ethernet Acceptable Framing Policy Type.

TEXTUAL-CONVENTION

Describes the Protocol Disposition Type on an interface.

TEXTUAL-CONVENTION

Describes the Control Protocol Filter Types.

TEXTUAL-CONVENTION

Describes the Ethernet Diagnosis Auto Negotiation Condition Result.

TEXTUAL-CONVENTION

Describes the Ethernet Diagnosis Cable Condition Result.

TEXTUAL-CONVENTION

Describes the Ethernet Diagnosis EFM OAM Loopback Condition Result.

TEXTUAL-CONVENTION

Describes the Ethernet Diagnosis Loopback Condition Result.

TEXTUAL-CONVENTION

ECPA Test Status.

TEXTUAL-CONVENTION

Describes the Ethernet Diagnosis Action. autoNeg - Auto negotiation capability, cable - Cable diagnostics, cable fault loopback- Terminal loopback with traffic injection and monitoring efm-oam-lpbk- EFM OAM loopback all - autoNeg, cable tests and loopback, not include efm-oam-lpbk.

TEXTUAL-CONVENTION

Describes the Ethernet MDIX Type. auto-mdix - Auto MDIX crossed - Crossed uncrossed - Uncrossed.

TEXTUAL-CONVENTION

Describes the Ethernet Service Port Mode Type.

TEXTUAL-CONVENTION

Describes the Ethernet Service Type. epl - Ethernet Private Linei, Port-based, all-to-one bundling evpl - Ethernet Virtual Private Line, VLAN based, service multiplexed.

TEXTUAL-CONVENTION

Describes the Ethernet Service Type, including port-based and vlan-based.

TEXTUAL-CONVENTION

Describes the Ethernet Flow Type. portbased - Port based Flow with full bandwidth of port; this Flow does not do VLAN/MAC based processing regular - Connection-oriented, VLAN based service default - Connection-oriented, service that matches all VLANs.

TEXTUAL-CONVENTION

Describes the Link Loss Forwarding Signal Types.

TEXTUAL-CONVENTION

Describes the Link Loss Forwarding Trigger Types.

TEXTUAL-CONVENTION

Describes the Link Loss Forwarding Tx Action Types.

TEXTUAL-CONVENTION

Describes the Loopback Types.

TEXTUAL-CONVENTION

Describes the OAM Admin State.

TEXTUAL-CONVENTION

Describes the OAM Discovery State.

TEXTUAL-CONVENTION

Describes the OAM Mode.

TEXTUAL-CONVENTION

Remote Link Ids used to match for Link Loss Forwarding.

TEXTUAL-CONVENTION

Describes the SWAP SADA Types supported. no-swapSADA - No swapping of Source MAC and Destination MAC swapSADA - Do swapping of Source MAC and Destination MAC swapDAOverrideSA - Swap Destination MAC as Source MAC, override source MAC with local MAC swapSADAMacOnly - Not supported swapDAOverridesSAMacOnly - Not supported swapIP - Do swapping of Source MAC and Destination MAC, Source IP and Destination IP swapTCPUDP - Do swapping of Source MAC and Destination MAC, Source IP and Destination IP, Source TCP/UDP port and Destination TCP/UDP port.

TEXTUAL-CONVENTION

Constellation Type of GPS Antenna

TEXTUAL-CONVENTION

Indicates GNSS constellation types supported by a GNSS Receiver Port. The valid bits must be set in order for this attribute to contain valid information. The representation of each bit setting (0 or 1) is indicated below. Bit Field Flag Description --------- ------------------------------------ 0 1 = GPS is supported; 0 = GPS not supported 1 1 = GLONASS is supported; 0 = GLONASS is not supported 2 1 = BEIDOU is supported; 0 = BEIDOU is not supported 3 1 = GALILEO is supported; 0 = GALILEO is not supported 4 1 = SBAS is supported; 0 = SBAS is not supported

TEXTUAL-CONVENTION

EoMpls Cos Mapping mode

TEXTUAL-CONVENTION

DHCP role type

TEXTUAL-CONVENTION

DEI Outer Tag Type.

TEXTUAL-CONVENTION

Defines the units of GNSS Antenna Cable Delay value

TEXTUAL-CONVENTION

Dynamic Model Type of GNSS Receiver

TEXTUAL-CONVENTION

Enumerations for E1/T1 Frame Format. none, t1-sf, t1-esf, e1-unframed, e1-crc4, e1-dualframe, e1-basicframe.

TEXTUAL-CONVENTION

Enumerations for E1/T1 Line Code. none, t1-b8zs, t1-ami, e1-hdb3, e1-ami.

TEXTUAL-CONVENTION

Enumerations for E1/T1 Line Type. t1, e1

TEXTUAL-CONVENTION

Enumerations for E1/T1 Receive Sensitivity high-range, low-range

TEXTUAL-CONVENTION

Describes the Frame Format of E3/T3.

TEXTUAL-CONVENTION

Describes the type of the E3/T3.

TEXTUAL-CONVENTION

Describes the Elephant Flow identification fields.

TEXTUAL-CONVENTION

five-tuple - 5-field identifier seven-tuple - 7-field identifier

TEXTUAL-CONVENTION

Describes the EoTDM Mode.

TEXTUAL-CONVENTION

Traffic Model for Ethernet Port.

TEXTUAL-CONVENTION

Describes the 3G Dcn Pin Code Action Types.

TEXTUAL-CONVENTION

Describes the Connection State of the 3G Usb Modem.

TEXTUAL-CONVENTION

Describes the Recived Signal Strength of the 3G Usb Modem.

TEXTUAL-CONVENTION

Describes the 3G Usb Sim Card States.

TEXTUAL-CONVENTION

Defines types of Flow.

TEXTUAL-CONVENTION

Describes the Ethernet Flow Tag Control Type.

TEXTUAL-CONVENTION

Describes the Flow Traffic Type. shaped-only, policed-shaped, policed-only.

TEXTUAL-CONVENTION

Describes the Ethernet Flow Action. Used for adding/removing VLAN members

TEXTUAL-CONVENTION

Frequency Identifier.

TEXTUAL-CONVENTION

Disabled (PIN protection is disabled) OK (PIN protection is enabled and PIN code is correct) Input PIN (input PIN to unlock) Input PUK (PIN code is locked, input PUK to unlock) Locked (must contact with SIM provider).

TEXTUAL-CONVENTION

Describes the GFP Encapsulation of the traffic port.

TEXTUAL-CONVENTION

G.Metro Auto Tuning Mode.

TEXTUAL-CONVENTION

Enumerations for GPS Antenna Status

TEXTUAL-CONVENTION

ITU C-band Channel Identifier.

TEXTUAL-CONVENTION

Installation Type of GPS Antenna

TEXTUAL-CONVENTION

Enumerations for IRIG Control Field.

TEXTUAL-CONVENTION

Enumerations for .

TEXTUAL-CONVENTION

Enumerations for IRIG Group Extension Type.

TEXTUAL-CONVENTION

Enumerations for IRIG Output Type.

TEXTUAL-CONVENTION

Enumerations for IRIG Relay Operation. Relay state can be configured to toggle once per hour, once per minute, to stay active (locked), or to stay inactive (alarm).

TEXTUAL-CONVENTION

Enumerations for .

TEXTUAL-CONVENTION

Describes Action on ingress frames when the number of MAC Table entires has reached the maximum defined by tableSize

TEXTUAL-CONVENTION

Learning Action: noAction - No Action flushFwdTable - Removes all dynamic entries from the Forwarding table of a Flow. clearBlock - removes the secondary state of BLCKD and transitions the flow to a state where frames are not blocked resetAgingTimer - reset the aging timer

TEXTUAL-CONVENTION

none, 0-133ft, 133-266ft, 266-399ft, 399-533ft, 533-655ft, 7dot5db, 15db, 22dot5db.

TEXTUAL-CONVENTION

Describes location mode for the GNSS receiver on OSA540X.

TEXTUAL-CONVENTION

Describes the Multiplexing Structure.

TEXTUAL-CONVENTION

OCN/STM Port Type.

TEXTUAL-CONVENTION

Out Of Band Channel Status.

TEXTUAL-CONVENTION

Specify pppoe connection status.

TEXTUAL-CONVENTION

Enumerations for PPS Generation Condition tracked-1sat, tracked-3sat

TEXTUAL-CONVENTION

Describes the PPS Input Rate.

TEXTUAL-CONVENTION

Describes the PPS physical interface type.

TEXTUAL-CONVENTION

Enumerations for NonStandardPD disabled:don't support non-standard PD, enabled:support non-standard PD

TEXTUAL-CONVENTION

Enumerations for PCP Drop Eligibility Encode Type. enc-none, enc-7p1d, enc-6p2d, enc-5p3d, enc-custom.

TEXTUAL-CONVENTION

none, apply-pairs.

TEXTUAL-CONVENTION

Plug Mode.

TEXTUAL-CONVENTION

Plug Type.

TEXTUAL-CONVENTION

Power over ethernet status

TEXTUAL-CONVENTION

Describes the Policer Algorithm Type.

TEXTUAL-CONVENTION

Describes the Policer Color Mode.

TEXTUAL-CONVENTION

Defines Policing Control options.

TEXTUAL-CONVENTION

Port states for the eight 16xbits card ports.

TEXTUAL-CONVENTION

Enumerations for the Polarity of the PPS Port interfaces.

TEXTUAL-CONVENTION

Enumerations for the impedance mode of the PPS Port interfaces.

TEXTUAL-CONVENTION

Describes the Priority Mapping Control Type.

TEXTUAL-CONVENTION

Defines the power level for pse port. class1 (4.00 Watts) :0 class2 (7.00 Watts) :1 class0andclass 3 (15.4 Watts):2 class4 (30 Watts):3.

TEXTUAL-CONVENTION

Relative Channel Identifier.

TEXTUAL-CONVENTION

Receive DEI Action.

TEXTUAL-CONVENTION

Enumerations for SA Bit Desgination. none, bit4, bit5, bit6, bit7, bit8.

TEXTUAL-CONVENTION

Bit states for the five Sa Bits from bit4 to bit8.

TEXTUAL-CONVENTION

Satellite Health of GNSS Satellite

TEXTUAL-CONVENTION

Describes the SCI Port QL.

TEXTUAL-CONVENTION

Describes the SCI Port Signal Direction.

TEXTUAL-CONVENTION

Describes the SCI Port Signal Mode.

TEXTUAL-CONVENTION

Describes Channel number of WDM tunable XFP setting.

TEXTUAL-CONVENTION

port-based - traffic shaping at Port level flow-based - traffic shaping at Flow level llq - low latency queuing

TEXTUAL-CONVENTION

Enumerations for Signal Frequency.

TEXTUAL-CONVENTION

Enumerations for Frequency Signal Shape. It can be sine or square wave signal.

TEXTUAL-CONVENTION

Describes SyncE mode (master or slave) on OSA540X ethernet port.

TEXTUAL-CONVENTION

Describes how RX quality level is utilized on OSA540X ethernet port.

TEXTUAL-CONVENTION

Describes the path type.

TEXTUAL-CONVENTION

Output Format of TOD Port

TEXTUAL-CONVENTION

Describes time advance mode for the GNSS on OSA540X.

TEXTUAL-CONVENTION

Enumerations for functionality that can be enabled or disabled.

TEXTUAL-CONVENTION

Learning Action: no-action - No Action delete-esa-entities - Removes all esa entities relate to this port. delete-cfm-entities - Removes all cfm entities relate to this port.

TEXTUAL-CONVENTION

Describes the Trail Trace Format.

TEXTUAL-CONVENTION

Transmit DEI Action.

TEXTUAL-CONVENTION

Mobile network type: none secondGeneration - 2G. thirdGeneration - 3G, fourthGeneration - 4G, notApplicable.

TEXTUAL-CONVENTION

Types of usb operational mode.

TEXTUAL-CONVENTION

The vdsl profile.

TEXTUAL-CONVENTION

The vdsl profile, no bit set means unknow.

TEXTUAL-CONVENTION

Type of WIFI encryption

TEXTUAL-CONVENTION

Specify xdsl annex version depends on modulation. annexa -- Annex A annexb -- Annex B annexc -- Annex C annexl -- ADSL2+ Annex L annexm -- ADSL2+ Annex M

TEXTUAL-CONVENTION

The xdsl carrier set.

TEXTUAL-CONVENTION

The xdsl control channel.

TEXTUAL-CONVENTION

The xdsl mode.

TEXTUAL-CONVENTION

Specify xdsl modulation type.

TEXTUAL-CONVENTION

The vdsl status.

TEXTUAL-CONVENTION

Specifies the Ethernet 10G port PHY type. not-applicable - for non-10G ports lan - 10G LAN-PHY mode (10GBASE-R) operating at 10Gb/sec wan - 10G WAN-PHY mode (10GBASE-W) operating at 9.29Gb/sec

OBJECT-IDENTITY

OBJECT-TYPE

A list of entries corresponding to Ethernet Access Port Facilities for configuration purposes.

OBJECT-TYPE

A conceptual row in the cmEthernetAccPortTable.

OBJECT-TYPE

An integer index value used to uniquely identify this Ethernet Access Port within a card. Note that each Ethernet Access Port is uniquely identified by the indices neIndex, shelfIndex, slotIndex, cmEthernetAccPortIndex. From release 5.6CC zero value becomes valid. The zero value is used in Network Element level objects which contain cmEthernetAccPortIndex in the index which is not-applicable for these objects e.g. Pass-thru Flows, Shapers or Policers.

OBJECT-TYPE

This object has the same value as ifIndex for Ethernet Access Port. An integer index value used to uniquely identify this Ethernet Access Port.

OBJECT-TYPE

Entity Index from ENTITY-MIB for this port.

OBJECT-TYPE

This object represents the Administrative State of the Ethernet Access Port.

OBJECT-TYPE

This object represents the Operational State of the Ethernet Access Port.

OBJECT-TYPE

This object represents the Secondary State of the Ethernet Access Port.

OBJECT-TYPE

This object provides the MTU on the Ethernet Access Port. The object is made read-write for FSP150CC devices.

OBJECT-TYPE

This object represents the type of Ethernet Media on the Ethernet Access Port.

OBJECT-TYPE

This object allows to configure the speed of the Ethernet Access Port.

OBJECT-TYPE

This object provides the negotiated speed of the Ethernet Access Port.

OBJECT-TYPE

This object allows management of MDIX property on Ethernet Access Port.

OBJECT-TYPE

This object allows enabling/disabling jumbo frames support on the Ethernet Access Port. This object is only applicable for Ethernet Access Port on R3.1CM NTU Card.

OBJECT-TYPE

This object provides the vendor name of the SFP. This is applicable when cmEthernetAccPortMediaType is fiber or coppersfp.

OBJECT-TYPE

This object provides the part number of the SFP. This is applicable when cmEthernetAccPortMediaType is fiber or coppersfp.

OBJECT-TYPE

This object provides the serial number of the SFP. This is applicable when cmEthernetAccPortMediaType is fiber or coppersfp.

OBJECT-TYPE

This object provides the date of manufacture of the SFP. This is applicable when cmEthernetAccPortMediaType is fiber or coppersfp.

OBJECT-TYPE

This object provides the SFP connector value. This is applicable when cmEthernetAccPortMediaType is fiber or coppersfp.

OBJECT-TYPE

This object allows to initiate Etherjack diagnosis on the Ethernet Access Port.

OBJECT-TYPE

This object provides diagnosis results for the cable Pair 1 on Ethernet Access Port.

OBJECT-TYPE

This object provides diagnosis results for the cable Pair 2 on Ethernet Access Port.

OBJECT-TYPE

This object provides diagnosis results for the cable Pair 3 on Ethernet Access Port.

OBJECT-TYPE

This object provides diagnosis results for the cable Pair 4 on Ethernet Access Port.

OBJECT-TYPE

This object provides auto negotiation results of the diagnosis test on Ethernet Access Port.

OBJECT-TYPE

This object provides port loopback results of the diagnosis test on Ethernet Access Port.

OBJECT-TYPE

This object provides remote EFM loopback results of the diagnosis test on Ethernet Access Port.

OBJECT-TYPE

This object provides results of the diagnosis test in string form on Ethernet Access Port.

OBJECT-TYPE

This object provides the current status of the diagnosis test on Ethernet Access Port.

OBJECT-TYPE

This object provides the time when diagnosis test was last executed.

OBJECT-TYPE

This object allows to initiate loopbacks on on the Ethernet Access Port.

OBJECT-TYPE

This object provides status of the current loopback on the Ethernet Access Port.

OBJECT-TYPE

This object allows to specify time for timed-loopbacks on on the Ethernet Access Port.

OBJECT-TYPE

This object allows to specify whether or not the loopbacked frame will have the Source Address and Destination Address swapped.

OBJECT-TYPE

This object allows specification of the outer VLANs to be looped back when port is in vlan(terminal/facility) loopback configuration. Only 3 VLANs can be specified for vlan loopback. The various bit positions are: 1 Outer VLAN 1 Loopback Enabled 2 Outer VLAN 2 Loopback Enabled 4 Outer VLAN 3 Loopback Enabled Value of 0 means that no VLANs are enabled.

OBJECT-TYPE

This object allows specification of the outer VLAN 1 to be looped back when port is in vlan(terminal/facility) loopback configuration. This is valid only if the corresponding bit in cmEthernetAccPortOuterVlanLoopbackMask is set. The value to be specified should be in the form X-Y where X is the VLAN Id and Y is the VLAN Priority. If Y is specified as a *, all Priorities (0 to 7) are looped back.

OBJECT-TYPE

This object allows specification of the outer VLAN 2 to be looped back when port is in vlan(terminal/facility) loopback configuration. This is valid only if the corresponding bit in cmEthernetAccPortOuterVlanLoopbackMask is set. The value to be specified should be in the form X-Y where X is the VLAN Id and Y is the VLAN Priority. If Y is specified as a *, all Priorities (0 to 7) are looped back.

OBJECT-TYPE

This object allows specification of the outer VLAN 3 to be looped back when port is in vlan(terminal/facility) loopback configuration. This is valid only if the corresponding bit in cmEthernetAccPortOuterVlanLoopbackMask is set. The value to be specified should be in the form X-Y where X is the VLAN Id and Y is the VLAN Priority. If Y is specified as a *, all Priorities (0 to 7) are looped back.

OBJECT-TYPE

This object allows specification of the inner VLANs to be looped back when port is in vlan(terminal/facility) loopback configuration. Only 3 VLANs can be specified for vlan loopback. The various bit positions are: 1 Inner VLAN 1 Loopback Enabled 2 Inner VLAN 2 Loopback Enabled 4 Inner VLAN 3 Loopback Enabled Value of 0 means that no VLANs are enabled.

OBJECT-TYPE

This object allows specification of the inner VLAN 1 to be looped back when port is in vlan(terminal/facility) loopback configuration. This is valid only if the corresponding bit in cmEthernetAccPortInnerVlanLoopbackMask is set. The value to be specified should be in the form X-Y where X is the VLAN Id and Y is the VLAN Priority. If Y is specified as a *, all Priorities (0 to 7) are looped back.

OBJECT-TYPE

This object allows specification of the inner VLAN 2 to be looped back when port is in vlan(terminal/facility) loopback configuration. This is valid only if the corresponding bit in cmEthernetAccPortInnerVlanLoopbackMask is set. The value to be specified should be in the form X-Y where X is the VLAN Id and Y is the VLAN Priority. If Y is specified as a *, all Priorities (0 to 7) are looped back.

OBJECT-TYPE

This object allows specification of the inner VLAN 3 to be looped back when port is in vlan(terminal/facility) loopback configuration. This is valid only if the corresponding bit in cmEthernetAccPortInnerVlanLoopbackMask is set. The value to be specified should be in the form X-Y where X is the VLAN Id and Y is the VLAN Priority. If Y is specified as a *, all Priorities (0 to 7) are looped back.

OBJECT-TYPE

This object allows enabling/disabling link loss forwarding on the Ethernet Access Port.

OBJECT-TYPE

This object allows definition of the link loss forwarding signalling type. This is applicable only if cmEthernetAccPortLinkLossFwdEnabled is enabled. This object is applicable only for FSP150CM Release 3.1. This object is deprecated henceforth. Link Loss signalling will be supported using the object cmEthernetAccPortLinkLossFwdTxActionType.

OBJECT-TYPE

This object allows definition of the link loss forwarding trigger types. This is applicable only if cmEthernetAccPortLinkLossFwdEnabled is enabled.

OBJECT-TYPE

This object allows specification of the delay between detection of link loss and signalling of link loss forwarding. Time specified is in seconds.

OBJECT-TYPE

This object provides the link loss forwarding status indicating if link loss forwarding is currently being signaled via the port.

OBJECT-TYPE

This object provides the indication of a link partners ability to support link loss forwarding via EFM, i.e. from received organization specific OAMPDUs.

OBJECT-TYPE

This object allows configuration of the Local Link Id on Ethernet access port.

OBJECT-TYPE

This object allows enabling/disabling Remote Link Ids on Ethernet access port. By setting the appropriate bit positions, the Ethernet access port is able to distinguish the remote side client ports from the Remote Link Down PDUs coming from remote end.

OBJECT-TYPE

OAM Id. This is unique EFM OAM sublayer port id.

OBJECT-TYPE

Ethernet Access Port's EFM OAM Disposition. This object is applicable only for FSP150CM Release 3.1. This object is deprecated henceforth. With FSP150CC Release 4.1, this property is managed using the Control Protocol Disposition tables.

OBJECT-TYPE

Ethernet Access Port's OAM discovery state.

OBJECT-TYPE

This object allows specification of whether the Ethernet Access Port supports sending variable response OAMPDUs.

OBJECT-TYPE

This object allows specification of whether the Ethernet Access Port supports interpreting Link Events.

OBJECT-TYPE

This object allows specification of whether the Ethernet Access Port is capable of OAM remote loopback mode.

OBJECT-TYPE

This object allows specification of whether the Ethernet Access Port is capable of sending OAMPDUs when the receive path is non-operational.

OBJECT-TYPE

This object represents the largest OAMPDU, in octets, supported by the Ethernet Access Port. This value is compared to the remote Maximum PDU Size and the smaller of the two is used.

OBJECT-TYPE

This object allows to configure the OAM sublayer entity in either Active or Passive mode.

OBJECT-TYPE

This object allows retrieval of the Remote Mac Address.

OBJECT-TYPE

This object allows retrieval of whether the remote OAM entity supports sending variable response OAMPDUs.

OBJECT-TYPE

This object allows retrieval of whether the remote OAM entity supports interpreting Link Events.

OBJECT-TYPE

This object allows retrieval of whether the remote OAM entity supports OAM remote loopback mode.

OBJECT-TYPE

This object allows retrieval of whether the remote OAM entity is capable of sending OAMPDUs when the receive path is non-operational.

OBJECT-TYPE

This object allows retrieval of the remote OAM entity maximum OAMPDU size.

OBJECT-TYPE

This object allows to retrieve whether the remote OAM sublayer entity is either in Active or Passive mode.

OBJECT-TYPE

This object allows specification of whether the Ethernet Access Port is in a connection-oriented (offering VLAN based services) mode or connection-less (offering MAC based services) mode.

OBJECT-TYPE

This object allows specification of whether the Ethernet Access Port provides transparent port based services, or multi-flow VLAN based services.

OBJECT-TYPE

This object allows management of RX pause frames on Ethernet Access port. This object is applicable only for FSP150CM Release 3.1. This object is deprecated henceforth. With FSP150CC Release 4.1, this property is managed using the Control Protocol Disposition tables.

OBJECT-TYPE

This object allows enabling/disabling transmit pause frames on Ethernet Access port.

OBJECT-TYPE

This object allows specification of the Acceptable Frame Policy on Ethernet Access port. Users can specify whether the port supports only tagged frames, only untagged frames or both tagged and untagged frames.

OBJECT-TYPE

This object provides the current MDIX status of the Ethernet Access port.

OBJECT-TYPE

This object provides the SFP Reach in meters. This is applicable when cmEthernetAccPortMediaType is fiber or coppersfp.

OBJECT-TYPE

This object provides the SFP Laser Wave Length in nano meters. This is applicable only when cmEthernetAccPortMediaType is fiber.

OBJECT-TYPE

This object provides the SFP Media Type. This is applicable when cmEthernetAccPortMediaType is fiber or coppersfp.

OBJECT-TYPE

This object allows to manage the EFM OAM on Ethernet Access Port.

OBJECT-TYPE

This object provides the EFM OAM Admin State.

OBJECT-TYPE

This object allows to manage the Access Port Shaping. When enabled, values in cmEthernetAccPortShapedSpeedLo and cmEthernetAccPortShapedSpeedHi are applicable.

OBJECT-TYPE

This object allows to specify the lower 32 bits of the Access Port Shaped speed. This value is applicable when cmEthernetAccPortShapingEnabled is enabled.

OBJECT-TYPE

This object allows to specify the higher 32 bits of the Access Port Shaped speed. This value is applicable when cmEthernetAccPortShapingEnabled is enabled.

OBJECT-TYPE

This object allows to specify the Q-in-Q Ether Type on the Access Port. Setting this value to 0 will disable the Q-in-Q override on the Access Port.

OBJECT-TYPE

This object allows to enable/disable the RX PAUSE on the Access Port. This object is not applicable for FSP150CM NTU Card. On NTU Card cmEthernetAccPortRxPauseDisposition object should be used to provision RxPause disposition.

OBJECT-TYPE

This object allows to enable or disable the automatic Cable Diagnostic tests when the cable is removed from the port.

OBJECT-TYPE

This object allows to specify the Access Port's behavior when link loss forwarding trigger events occur on the Network Port. This provides ability to configure per access port LLF behavior.

OBJECT-TYPE

This object provides the received Remote Link IDs in EFM RLD messages on the Access Port.

OBJECT-TYPE

This object allows to enable or disable the VLAN trunking on Ethernet Access port. Disabling VLAN trunking removes all VLAN tags before transmitting traffic out of the access port. This object is only applicable for connection-oriented, evpl service type.

OBJECT-TYPE

This object allows to specify whether cmEthernetAccPortPortVlanId value will be PUSHed on untagged frames or not in the Access to Network direction. This object is only applicable for connection-oriented, evpl service type.

OBJECT-TYPE

This object allows to specify whether cmEthernetAccPortPortVlanId value will be POPed in the Network to Access direction. This object is only applicable for connection-oriented, evpl service type.

OBJECT-TYPE

This object allows to specify the Ethernet Access Port VLAN Id to PUSH on untagged frames in the Access to Network direction. This object is only applicable for connection-oriented, evpl service type, when cmEthernetAccPortA2NPushPVIDEnabled is set to true.

OBJECT-TYPE

This object allows to specify the Ethernet Access Port VLAN Priority for the PUSHed VLAN tag (specified by cmEthernetAccPortPortVlanId) on untagged frames in the Access to Network direction. This object is only applicable for connection-oriented, evpl service type, when cmEthernetAccPortA2NPushPVIDEnabled is set to true.

OBJECT-TYPE

This object allows to specify the Ethernet Access Port Priority Mapping Mode used for classification of frames. This object is only applicable for connection-oriented, evpl service type.

OBJECT-TYPE

This object allows to specify whether the Ethernet Access Port can be enabled/disabled for Synchronous Ethernet. This object is only applicable for Synchronous Ethernet capable ports. When enabled, on receive side -port can extract the frequency of its input signal and pass the recovered clock to the system clock -port processes the ESMC(Ethernet Synchronization Messaging Channel) and extracts the QL (when also QL enabled) -port is eligible to be selected as a system clock reference When enabled, on transmit side -port's transmit clock is locked to the system clock -port generates an ESMC to generate a QL (when also QL enabled) When disabled, on receive side, -port does not pass the recovered clock to the system clock -port does not process the ESMC (if present) -port is not eligible to be selected as a system clock reference When disabled, on transmit side -port's output frequency may be synchronized to the system clock -port does not generate an ESMC.

OBJECT-TYPE

This object allows to specify whether the Ethernet Access Port can be enabled/disabled for QL Mode. This object is only applicable for Synchronous Ethernet capable ports, when cmEthernetAccPortQLModeEnabled is set to true. When enabled, on receive side -port shall PEER the SSM (Sync Status Messages) slow protocol PDUs and take appropriate action When enabled, on transmit side -port shall periodically (once a second) transmit QL TLV information PDUs When disabled, on receive side, -port shall terminate and discard any SSM slow protocol PDUs When disabled, on transmit side -port shall not transmit any SSM slow protocol PDUs.

OBJECT-TYPE

This object allows to specify the expected QL when the Ethernet Access Port is enabled for QL Mode. This object is only applicable for Synchronous Ethernet capable ports, when cmEthernetAccPortQLModeEnabled is set to true. This object allows the user to set a minimum expected received Quality Level on the port. The valid values depend upon the SYNC entity's Network Clock Type. A value of None represents that a minimum Quality Level is not expected. The default value shall be None.

OBJECT-TYPE

This object allows to specify the assumed QL on the Ethernet Access Port. This object is only applicable for Synchronous Ethernet capable ports. The Assumed QL is only meaningful if the Network Clock Type (see fsp150cm-sync.mib) is option1 and the port's QL Mode is disabled and the port is being used as an input reference source. Under these conditions, the specified QL value is assumed to be the Quality Level of the non-failed reference.

OBJECT-TYPE

This object provides the Received QL value for the Ethernet port. If the Ethernet port's QL Mode is disabled, then the received QL value is not applicable.This object is only applicable for Synchronous Ethernet capable ports.

OBJECT-TYPE

This object provides the Transmitted QL value for the Ethernet port. If the Ethernet port's QL Mode is disabled, then the received QL value is not applicable. This object is only applicable for Synchronous Ethernet capable ports.

OBJECT-TYPE

This is a port level control to reset the DEI (Drop Eligibility Indicator) bit in the S-Tag, if the downstream equipment supports S-Tag TPID (EtherType) but cannot handle DEI bit set. In the receive direction, it uses the S-TAG DEI when enabled, else ignores it. The following comment is NOT relevant to OSA8.1.1, since this object is still supported by OSA8.1.1. The object has been deprecated. The respective configuration should be managed by following objects: cmEthernetAccPortRxDeiAction, cmEthernetAccPortTxDeiAction, cmEthernetAccPortRxDeiOuterTagType, cmEthernetAccPortTxDeiOuterTagType.

OBJECT-TYPE

This is a port level control that specifies the mode of drop eligibility encoding in PCP bits of the VLAN tag.

OBJECT-TYPE

This object allows the SNMP user to manage the Priority Code Point (PCP) Drop Eligibility Pairs. When the cmEthernetAccPortPcpDEEncType is of type 7p1d, 6p2d, 5p3d, the cmAccPortPcpDEPairTable can be used to specify alternate pairs of priorities to specify drop eligibility/ ineligibility.

OBJECT-TYPE

This object allows retrieval of the Remote Mac Address, when the port is peering using SSM.

OBJECT-TYPE

This object allows to specify the PHY type of 10G Ethernet Port. 10G ports can operate in LAN-PHY or WAN-PHY mode. The default mode is LAN-PHY and port rate in this mode is 10Gbps. In WAN-PHY mode the port rate is 9.29Gbps. This attribute is only applicable for ports configured to work at speed-10G-full. For other speeds the value of this object must be 'not-applicable' and cannot be changed.

OBJECT-TYPE

This object allows to Enable/Disable the Acc Port Source MAC Address frame matching criteria for all streams. Not applicable for: efm-oam-remote, efm-oam-remote-timed.

OBJECT-TYPE

This object allows to Enable/Disable the Acc Port Destination MAC Address frame matching criteria for all streams. Not applicable for: efm-oam-remote, efm-oam-remote-timed.

OBJECT-TYPE

This object allows to set Acc Port Source MAC Address for frame matching when Acc Port Source MAC Control is enabled.

OBJECT-TYPE

This object allows to set Acc Port Destination MAC Address for frame matching when Acc Port Destination MAC Control is enabled.

OBJECT-TYPE

This object allows frame blocking when loopback is active. - True: Blocks frames in the non-loopback direction that match the PORT or VLAN received in the non-loopback direction. Discards frames in the loopback direction that match the PORT or VLAN, but do not match the MAC address criteria, - False: No blocking of frames.

OBJECT-TYPE

This object allows to specify the Receive DEI Action.

OBJECT-TYPE

This object allows to specify the Transmit DEI Action.

OBJECT-TYPE

This object allows to specify the Receive DEI Outer Tag Type.

OBJECT-TYPE

This object allows to specify the Transmit DEI Outer Tag Type.

OBJECT-TYPE

Channel number of WDM tunable XFP setting.

OBJECT-TYPE

Channel number of WDM tunable XFP setting.

OBJECT-TYPE

Channel number of WDM tunable XFP setting.

OBJECT-TYPE

This object provides the auto selected Ethernet Media of the Ethernet Access Port.

OBJECT-TYPE

This object allows to Enable/Disable the Low Latency Queuing on the Ethernet Access Port.

OBJECT-TYPE

This object allows to Enable/Disable the Swapping of Priority Vlan Id in the A2N direction.

OBJECT-TYPE

This object allows to Enable/Disable the Swapping of Priority Vlan Id in the N2A direction.

OBJECT-TYPE

This object allows to specify the value of Vlan Id for the Swapping of Priority Vlan Id operation for both the A2N and N2A direction.

OBJECT-TYPE

This object describes the diagnose mac address for SAT, ECPA, JDSU, Loopback with Override SA etc.

OBJECT-TYPE

Indicates which VLAN tag to use for PCP Priority to COS mapping when the port Priority Map Mode is 802.1p. Supported values are inner-vlantag and outer-vlantag. This attribute is only applicable on products when Flowpoint Model is supported. inner-vlantag: The inner VLAN tag PCP Priority of a frame is used for ingress COS mapping. A frame with no inner VLAN tag (untagged or single-tagged) will have a COS equal to the default COS of the port. outer-vlantag: The outer VLAN tag PCP Priority of a frame is used for ingress COS mapping. A frame with no outer VLAN tag (untagged) will have a COS equal to the default COS of the port. This attribute has been deprecated and is not supported. Now, the Priority Map Mode indicates whether it is inner or outer. Use priomap-8021p(4) for outer and priomap-8021p-inner(5) for inner.

OBJECT-TYPE

The COS assigned to a frame that does not have a valid COS identifier for the Priority Map Mode of the port. This attribute is only applicable on products when Flowpoint Model is supported. This value is assigned to a frame received on a port when: - the cmEthernetAccPortPrioMapMode=priomap-8021p, ingressCOSPriority=inner-vlantag; and the frame is untagged - the cmEthernetAccPortPrioMapMode=priomap-8021p, ingressCOSPriority=inner-vlantag; and the frame has a single VLAN tag - the cmEthernetAccPortPrioMapMode=priomap-8021p, ingressCOSPriority=outer-vlantag; and the frame is untagged - the cmEthernetAccPortPrioMapMode=priomap-dscp; and the frame does not have an IP ethertype - the cmEthernetAccPortPrioMapMode=priomap-tos; and the frame does not have an IP ethertype. This attribute has been deprecated and is not supported. The Default COS is determined from the flowpoint's associated Priority Mapping Profle.

OBJECT-TYPE

The Traffic Management connection model available for the port. - accessFlow: NID Traffic Connection model. - flowpoint: Multipoint and Aggregation Traffic Connection model.

OBJECT-TYPE

This object describes whether the shaper bw independent.

OBJECT-TYPE

This object is applicable when there is jdsu l3 loopback.

OBJECT-TYPE

This object used to specify the wfq segmentation cos value.

OBJECT-TYPE

This object used to specify the wfq group cos value.

OBJECT-TYPE

This object used to specify the wfq group eir low 32 bits value.

OBJECT-TYPE

This object used to specify the wfq group eir high 32 bits value.

OBJECT-TYPE

Allows enabling/disabling of silent start.

OBJECT-TYPE

This object provides the SFP Link Length. This is applicable only when cmEthernetTrafficPortMediaType is fiber or coppersfp.

OBJECT-TYPE

This object allows enabling/disabling of Outer Tag TPID override. When enabled, values in Outer Tag TPID is applicable on egress Ethernet Access Port.

OBJECT-TYPE

This object allows to specify the egress Outer Tag TPID on the Ethernet Access Port.

OBJECT-TYPE

This object provides the official name of the SFP.

OBJECT-TYPE

This object provides the hardware revision of the SFP.

OBJECT-TYPE

This object allows enabling/disabling of Persistent Loopback Control. The loopback configuration parameters do not survive restart as typically maintenance actions are not persist. Setting this attribute to true shall persist the loopback configuration parameters. When it is set to false the loopback configuration parameters shall not survive a restart.

OBJECT-TYPE

Control that enables/disables Test Reflector IPv4 Address to be used for Test Reflector IP Interface.

OBJECT-TYPE

This is the Test Reflector Interface IPv4 address.

OBJECT-TYPE

Control that enables/disables Test Reflector IPv6 Address to be used for Test Reflector IP Interface.

OBJECT-TYPE

This is the Test Reflector Interface IPv6 address.

OBJECT-TYPE

This object allows to manage (enable/disable) Power Over Ethernet Detection.

OBJECT-TYPE

This object provides the status of Power Over Ethernet Detection.

OBJECT-TYPE

This object provides the SFP identifier value.

OBJECT-TYPE

A list of entries corresponding to Ethernet Access Port Control Protocol Disposition. This table is only applicable for FSP150CM Hub Shelf Release 3.x.

OBJECT-TYPE

A conceptual row in the cmEthernetAccPortCpdTable. These entries represent a Control Protocol Disposition filtering criteria on the Ethernet Access Port.

OBJECT-TYPE

An arbitrary integer index value used to uniquely identify this CPD Service Entry.

OBJECT-TYPE

This enables specification of type of CPD Filter.

OBJECT-TYPE

This provides description of CPD Filter.

OBJECT-TYPE

This enables specification of disposion type of CPD Filter.

OBJECT-TYPE

This enables provides the Filter MAC Address to match.

OBJECT-TYPE

This enables provides the Filter MAC Address Mask to match.

OBJECT-TYPE

This enables provides the Filter Ethertype to match.

OBJECT-TYPE

This enables provides the Filter Ethertype Mask to match.

OBJECT-TYPE

This enables provides the Filter Subtype to match.

OBJECT-TYPE

This enables provides the Filter Subtype Mask to match.

OBJECT-TYPE

A list of entries corresponding to Ethernet Access Port Cable Length Benchmark.

OBJECT-TYPE

A conceptual row in the cmEthernetAccPortClbTable. These entries represent Cable Length Benchmarks on the Ethernet Access Port.

OBJECT-TYPE

An integer index value used to uniquely identify this Cable Length Benchmark Entry specification.

OBJECT-TYPE

This enables specification of Cable Length Benchmark entry.

OBJECT-TYPE

Cable length of Cable Points Entry. The cable length is of the form XXX[.YY] where XX can be any integer value and YY allows precision of 2 decimals after the floating point. Note that .YY is optional.

OBJECT-TYPE

A textual string containing description of cable span.

OBJECT-TYPE

A list of entries corresponding to Ethernet Flows for configuration purposes. If the corresponding Ethernet Access Port's cmEthernetAccPortMode is connection-oriented and cmEthernetAccPortSvcType is epl, there exists a single Flow in this table. No Flow creation or deletion is allowed on this table for FSP150CM NTU based services. Since Fsp150 R5.6CC release this table is used to manage 2 types of Flows: - Access Port Flow as in the previous releases - Tranparent Flow (new in 5.6CC) A Transparent Flow is Flow between Network-1 and Network-2 ports used to convey pass-thru traffic in the ring topology e.g. ERP. Few of the existing attributes will have new semantix for Transperent Flow. Transparent Flow is a NE level object and hence has different indexing than the Access Port Flow. The valid indices are neIndex and cmFlowIndex. The remaining indices will have constant values as follows: shelfIndex = 1 slotIndex = 255 cmEthernetAccPortIndex = 0

OBJECT-TYPE

A conceptual row in the cmFlowTable. These entries represent an Ethernet Flow.

OBJECT-TYPE

The integer index value corresponding to an Ethernet Flow.

OBJECT-TYPE

This object allows SNMP management entities to provide a circuit identifier with the Flow.

OBJECT-TYPE

This object represents the Administrative State of the Flow.

OBJECT-TYPE

This object represents the Operational State of the Flow.

OBJECT-TYPE

This object represents the Secondary State of the Flow.

OBJECT-TYPE

This object represents the type of the Flow.

OBJECT-TYPE

This object allows specification of multiple COS (Class of Service) Flow.

OBJECT-TYPE

This object represents the Commited Information Rate(CIR) of an Flow in the Access to Network (A2N) direction. For a portbased Flow(FSP150CM NTU, CPMR), this object is not settable. This value represents the lower 32-bits of the CIR. For a Multi COS flow, this value is settable only at creation time. In case of Tranparent Flow this object represents N1 to N2 CIR.

OBJECT-TYPE

This object represents the Excess Information Rate(EIR) on an Flow in the Access to Network (A2N) direction. For a portbased Flow(FSP150CM NTU, CPMR), this object is not settable. This value represents the lower 32-bits of the CIR. For a Multi COS flow, this value is settable only at creation time. In case of Tranparent Flow this object represents N1 to N2 EIR.

OBJECT-TYPE

This object allows management of the N2A rate limiting, independent of A2N rate limiting. When not enabled, N2A specification is the same as A2N. This object is not applicable for Tranparent Flow; the value should be FALSE.

OBJECT-TYPE

This object represents the Commited Information Rate(CIR) of an Flow in the Network to Access (N2A) direction. For a portbased Flow, this object is not settable. This is only settable if cmFlowN2ARateLimitingEnabled is enabled. In case of Tranparent Flow this object represents N2 to N1 CIR.

OBJECT-TYPE

This object represents the Excess Information Rate(CIR) of an Flow in the Network to Access (N2A) direction. For a portbased Flow, this object is not settable. This is only settable if cmFlowN2ARateLimitingEnabled is enabled. In case of Tranparent Flow this object represents N2 to N1 EIR.

OBJECT-TYPE

The type of storage configured for this entry.

OBJECT-TYPE

The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of cmFlowRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with cmFlowRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The cmFlowRowStatus object may be modified if the associated instance of this object is equal to active(1). Note that flow creation and deletion is only supported with access port in connection-oriented evpl mode.

OBJECT-TYPE

This object provides information on the type of traffic flow supported by the system, i.e.'shaped-only' flows (support only shaping) or 'policed-shaped' (support policing and shaping) flows. 'shaped-only' flow exists for FSP150CM NTU and CPMR access ports. 'policed-shaped' flows are supported in FSP150CC devices. Please note that this object refers to how traffic profiles are managed on devices and is independent of the policing enabling/disabling feature.

OBJECT-TYPE

This object allows specification of the COS (Class of Service) value for the Traffic Flow. This value is used at flow creation time to identify the COS level of the A2N and N2A shaper. In case of a multi-COS flow, this value is not applicable when multiple policers/shapers exist on the flow. This object is also applicable to specify the COS of a connection-oriented epl service.

OBJECT-TYPE

This object is applicable only when Port is in connection-oriented evpl mode. This attribute is mandatory if creation of connection-oriented evpl regular flow is desired. It allows specification of VLAN members of the Flow. VLAN members are comma separated, of the form X-Y where X is the VLAN Id and Y is the VLAN Priority. VLAN members can be of the form X-* or X (vlan X with all priorities), *-Y (all vlans with priority Y), and X1:X2 (range of vlans from X1 to X2, all priorities). Members with specific VLAN Id and specific VLAN Priority are not supported. Once the flow is created, this attribute can only be updated using cmFlowAction and cmFlowActionVlan objects.

OBJECT-TYPE

This object is applicable only when Port is in connection-oriented evpl mode and the cmFlowType is regular. This object allows to add or remove the VLAN members specified by cmFlowActionVlan object. SNMP manager must first configure the VLAN member to be added/removed in the object cmFlowActionVlan and then should specify cmFlowAction on whether to add/remove the specified VLAN member.

OBJECT-TYPE

This object is applicable only when Port is in connection-oriented evpl mode. This object allows adding/removing VLAN members to a connection-oriented evpl regular flow. VLAN member is of the form X-Y where X is the VLAN Id and Y is the VLAN Priority. VLAN members can be of the form X-* (vlan X with all priorities), *-Y (all vlans with priority Y), and X1:X2 (range of vlans from X1 to X2, all priorities). Members with specific VLAN Id and specific VLAN Priority are not supported. In order to add/remove VLAN member to a flow, user must specify this object with appropriate VLAN and then invoke cmFlowAction.

OBJECT-TYPE

This object is applicable only when Port is in connection-oriented evpl mode for a regular flow as well as default flow. This object allows to specify whether or not the flow supports untagged traffic.

OBJECT-TYPE

This object represents the Commited Information Rate(CIR) of an Flow in the Access to Network (A2N) direction. This value represents the upper 32 bits of CIR (lower is provided in cmFlowA2NCIR). For a Multi COS flow, this value is settable only at creation time. In case of Tranparent Flow this object represents N1 to N2 CIR.

OBJECT-TYPE

This object represents the Excess Information Rate(EIR) on an Flow in the Access to Network (A2N) direction. For a portbased Flow(FSP150CM NTU, CPMR), this object is not settable. This value represents the higher 32-bits of the CIR. For a Multi COS flow, this value is settable only at creation time. In case of Tranparent Flow this object represents N1 to N2 EIR.

OBJECT-TYPE

This object represents the Commited Information Rate(CIR) of an Flow in the Network to Access (N2A) direction. This value represents the upper 32 bits of CIR (lower is provided in cmFlowN2ACIR). For a Multi COS flow, this value is settable only at creation time. This is only settable if cmFlowN2ARateLimitingEnabled is enabled. In case of Tranparent Flow this object represents N2 to N1 CIR.

OBJECT-TYPE

This object represents the Excess Information Rate(EIR) on an Flow in the Network to Access (N2A) direction. For a portbased Flow(FSP150CM NTU, CPMR), this object is not settable. This value represents the higher 32-bits of the CIR. For a Multi COS flow, this value is settable only at creation time. This is only settable if cmFlowN2ARateLimitingEnabled is enabled. In case of Tranparent Flow this object represents N2 to N1 EIR.

OBJECT-TYPE

This object allows management of Hierarchical COS on the Flow.

OBJECT-TYPE

This object supports the Hierarchical Class of Service (HCOS) feature. It is only applicable for a flow with multiple class of services. This allows the provisioning of guaranteed bandwidth (lower 32 bits) of a flow. This value must be greater than or equal to the sum of all individual COS CIRs. In case of Tranparent Flow this object represents N1 to N2 and N2 to N1 guaranteed bandwidth.

OBJECT-TYPE

This object supports the Hierarchical Class of Service (HCOS) feature. It is only applicable for a flow with multiple class of services. This allows the provisioning of guaranteed bandwidth (upper 32 bits) of a flow. This value must be greater than or equal to the sum of all individual COS CIRs. In case of Tranparent Flow this object represents N1 to N2 and N2 to N1 guaranteed bandwidth.

OBJECT-TYPE

This object supports the Hierarchical Class of Service (HCOS) feature. It is only applicable for a flow with multiple class of services. This allows the provisioning of maximum bandwidth (lower 32 bits) of a flow. This is the peak limit of a flow. This value must be greater than or equal to the sum of all individual COS CIRs. In case of Tranparent Flow this object represents N1 to N2 and N2 to N1 maximum bandwidth.

OBJECT-TYPE

This object supports the Hierarchical Class of Service (HCOS) feature. It is only applicable for a flow with multiple class of services. This allows the provisioning of maximum bandwidth (upper 32 bits) of a flow. This is the peak limit of a flow. This value must be greater than or equal to the sum of all individual COS CIRs. In case of Tranparent Flow this object represents N1 to N2 and N2 to N1 maximum bandwidth.

OBJECT-TYPE

This object allows specification of the tag management operation on the C-TAG. Supported types are 'push', 'pushvid', 'swapvid' and 'none'. If the type is 'push', the VLAN Id (cmFlowCTagVlanId) and priority (cmFlowCTagVlanPriority) are pushed onto the frame; if the type is 'pushvid', only the VLAN Id (12 bits) is pushed, the Priority is copied from incoming tag's priority; if the type is 'swapvid', only the VLAN Id (12 bits) are swapped with the specified cmFlowCTagVlanId; if the type is 'none', no C-TAG management is performed. This object is not applicable for Tranparent Flow; the value should be 'none'.

OBJECT-TYPE

This object allows specification of the VLAN Id to be pushed or swapped, based on the value of cmFlowCTagControl. It is applicable for 'push', 'swapvid' and 'pushvid' control types. This object is not applicable for Tranparent Flow; the value should be 0.

OBJECT-TYPE

This object allows specification of the VLAN Priority to be pushed or swapped, based on the value of cmFlowCTagControl. It is applicable for 'push' control type. This object is not applicable for Tranparent Flow; the value should be 0.

OBJECT-TYPE

This object is used to specify whether the C-TAG priority be used or ignored for traffic in the N2A direction. This is only applicable if cmFlowCTagControl is 'push'. This object is not applicable for Tranparent Flow; the value should be FALSE.

OBJECT-TYPE

This object allows specification of the tag management operation on the S-TAG. Supported types are 'push', 'swapvid', and 'none'. If the type is 'push', the VLAN Id (cmFlowSTagVlanId) and priority (cmFlowSTagVlanPriority) are pushed onto the frame; if the type is 'swapvid', the VLAN Id(12 bits) is swapped with the specified cmFlowSTagVlanId; type is 'none', no S-TAG manament is performed. This object is not applicable for Tranparent Flow; the value should be 'none'.

OBJECT-TYPE

This object allows specification of the VLAN Id to be pushed, based on the value of cmFlowSTagControl. It is applicable for 'push' control type. This object is not applicable for Tranparent Flow; the value should be 0.

OBJECT-TYPE

This object allows specification of the VLAN Priority to be pushed, based on the value of cmFlowSTagControl. It is applicable for 'push' control type. This object is not applicable for Tranparent Flow; the value should be 0.

OBJECT-TYPE

This object is used to specify whether the flow participates in outer-tag priority swap. The Priority Mapping Table cmPrioMapTable allows the A2N outer-tag priority to be specified based on incoming priority at Access Port (based on priority mapping mode - 802.1P, TOS, DSCP). This object is not applicable for Tranparent Flow; the value should be FALSE.

OBJECT-TYPE

This object is used to specify whether the flow uses the inner-tag or the outer-tag in determining the COS (Class of Service) in the N2A direction. This object is applicable in the case of a Multi COS Flow. This object is not supported for Tranparent Flow;

OBJECT-TYPE

This object is used to specify the number of frames lost per flow that starts counting Errored Seconds (ES) on the flow. This functionality is applicable if the flow is monitored using the Y.1731 ESA functionality.

OBJECT-TYPE

This object is used to specify the frame-loss ratio per flow that starts counting Severely Errored Seconds (SES) on the flow. This functionality is applicable if the flow is monitored using the Y.1731 ESA functionality.

OBJECT-TYPE

This object is applicable only when Port is in connection-oriented mode. This object is applicable to both epl and evpl mode flows. This object allows to enable/disable the policing function on the flow.

OBJECT-TYPE

This object is applicable only when Port is in connection-oriented mode. This object is applicable to evpl mode Regular flows, when S-TAG control is specified as SWAPVID. When enabled, this attribute preserves the EtherType (0x88a8) and DEI (Drop Eligibility Indicator) bit in the incoming S-TAG (both from Access and Network Port perspective) into the outgoing S-TAG. When not enabled, the incoming tag is considered as a Q-TAG (0x8100) and both EtherType and CFI (Canonical Form Indicator) bits are over-written by the S-TAG Ethertype (0x88a8) and DEI bit. This object is not applicable for Tranparent Flow; the value should be FALSE.

OBJECT-TYPE

This object is used to specify whether the flow participates in inner-tag (second) priority swap. The Priority Mapping Table cmPrioMapTable allows the A2N inner-tag priority to be specified based on incoming priority at Access Port (based on priority mapping mode - 802.1P, TOS, DSCP). This object is not applicable for Tranparent Flow; the value should FALSE.

OBJECT-TYPE

This object is used to specify whether the flow participates in outer-tag priority swap in the A2N direction. The Priority Mapping Table cmNetPortPrioMapTable allows the N2A outer-tag priority to be specified based on incoming priority at Network Port (based on priority mapping mode - 802.1P, TOS, DSCP). This object is not applicable for Tranparent Flow; the value should be FALSE.

OBJECT-TYPE

This object is used to specify whether the traffic in A2N direction passing through this flow is shaped by port-level or flow-level Shapers. In case of portbased flows the value of this attribute is flow-based and cannot be changed. In case of regular and default flows Fsp150 products may support both port-based and flow-based shaping.

OBJECT-TYPE

This object is used to specify whether the traffic in N2A direction passing through this flow is shaped by port-level or flow-level Shapers. In case of portbased flows the value of this attribute is flow-based and cannot be changed. In case of regular and default flows Fsp150 products may support both port-based and flow-based shaping.

OBJECT-TYPE

This object indicates whether the S-TAG priority is used or ignored for traffic in the N2A direction. This is only applicable if cmFlowSTagControl is 'push'. This object is not applicable for Tranparent Flow; the value should be FALSE.

OBJECT-TYPE

This object is applicable for Flows on the PWE3 Ethernet Backplane Port. When set to TRUE bandwidth of this Flow will be automatically adjusted when PWE3 SATOPs are provisioned. The bandwidth will be adjusted based on the TDM entities of associated SATOPs. Flow on ports other than PWE3 Ethernet Backplane Port will always have this value set to FALSE and it is not configurable.

OBJECT-TYPE

This object specifies a physical or logical port on the Access side of the Flow. This can be Access Port, Access LAG or Access Split Horizion Group. In case of Tranparent Flow this object specifies port1 of the Flow which is Network-1.

OBJECT-TYPE

This object specifies a physical or logical port on the Network side of the Flow. This can be Network Port, Network LAG, Network Split Horizion Group ERP or Protection Group. In case of Tranparent Flow this object specifies port2 of the Flow which is Network-2.

OBJECT-TYPE

This object specifies the direction(s) in which Poling is enabled on traffic within this Flow when cmFlowPolicingEnabled is TRUE.

OBJECT-TYPE

This object specifies the percentage of available CIR on the Network ports assigned to this Flow when cmFlowAutoBandwidthConfigEnabled is TRUE. The flow guaranteedBW is set to available BW multiplied by this value. This object is only applicable to Tranparent Flow. The value of this object should be 0 for Access Flow.

OBJECT-TYPE

This object specifies the Loop Avoidance instance to which this Flow belongs. This object is appicable only for Transparent Flow and should point to the ERP instance for which this Flows carries pass-thru traffic. In case of Access Flow the value of this object should be zeroDotZero.

OBJECT-TYPE

This object specifies if this Flow is an Access Flow or Pass-thru Flow.

OBJECT-TYPE

This object is used to specify whether n2n forwarding is enabled on particular Flow.

OBJECT-TYPE

Whether multicast frames are limited per Flow.

OBJECT-TYPE

The rate limit for multicast packets per Flow. When cmFlowA2NMulticastRateLimiteControl is set and value is 0, then all multicast frames are dropped. This object represents the low-order 32-bits.

OBJECT-TYPE

The rate limit for multicast packets per Flow. When cmFlowA2NMulticastRateLimiteControl is set and value is 0, then all multicast frames are dropped. This object represents the high-order 32-bits.

OBJECT-TYPE

Whether broadcast frames are limited per Flow.

OBJECT-TYPE

The rate limit for multicast packets per Flow. When cmFlowA2NBroadcastRateLimiteControl is set and value is 0, then all multicast frames are dropped. This object represents the low-order 32-bits.

OBJECT-TYPE

The rate limit for multicast packets per Flow. When cmFlowA2NBroadcastRateLimiteControl is set and value is 0, then all multicast frames are dropped. This object represents the high-order 32-bits.

OBJECT-TYPE

Whether both multicast and broadcast frames are limited per Flow.

OBJECT-TYPE

The rate limit for multicast packets per Flow. When cmFlowA2NCombinedRateLimiteControl is set and value is 0, then all multicast frames are dropped. This object represents the low-order 32-bits.

OBJECT-TYPE

The rate limit for multicast packets per Flow. When cmFlowA2NCombinedRateLimiteControl is set and value is 0, then all multicast frames are dropped. This object represents the high-order 32-bits.

OBJECT-TYPE

This object used to specify the flow's profile.

OBJECT-TYPE

This object specifies EoMpls Pw object OID.

OBJECT-TYPE

This object used to specify the flow's N2A direction profile.

OBJECT-TYPE

This object can be used to enable/disable secure block.

OBJECT-TYPE

This object specifies the secure flow list, it should be f3ConnectGuardFlowIndex value list split with comma.

OBJECT-TYPE

This object specifies the secure state list, it should be secure state value list and split with comma. For detailed description how to identify values, please see FlowSecState in CM-COMMON-MIB.

OBJECT-TYPE

This object used to specify the flow related A2N shaper BW whether independent.

OBJECT-TYPE

This object used to specify the flow related wfq segmentation COS value.

OBJECT-TYPE

This object used to specify the flow related wfq group COS value.

OBJECT-TYPE

This object used to specify the flow related wfq group EIR low 32 bits value.

OBJECT-TYPE

This object used to specify the flow related wfq group EIR high 32 bits value.

OBJECT-TYPE

A list of entries corresponding to Flow Control Protocol Disposition. This table is only applicable for FSP150CM Hub Shelf Release 3.x.

OBJECT-TYPE

A conceptual row in the cmFlowCpdTable. These entries represent a Control Protocol Disposition filtering criteria on the Ethernet Network Port.

OBJECT-TYPE

An arbitrary integer index value used to uniquely identify this CPD Service Entry.

OBJECT-TYPE

This enables specification of type of CPD Filter.

OBJECT-TYPE

This provides description of CPD Filter.

OBJECT-TYPE

This enables specification of disposion type of CPD Filter.

OBJECT-TYPE

This enables provides the Filter MAC Address to match.

OBJECT-TYPE

This enables provides the Filter MAC Address Mask to match.

OBJECT-TYPE

This enables provides the Filter Ethertype to match.

OBJECT-TYPE

This enables provides the Filter Ethertype Mask to match.

OBJECT-TYPE

This enables provides the Filter Subtype to match.

OBJECT-TYPE

This enables provides the Filter Subtype Mask to match.

OBJECT-TYPE

A list of entries corresponding to Ethernet Quality of Service Shaper for configuration purposes.

OBJECT-TYPE

A conceptual row in the cmQosShaperTable. These entries represent a Quality of Service Shaper.

OBJECT-TYPE

The unique index value corresponding to a Quality of Service Shaper's direction. Values 1 and 2 are applicable to the Access Flow Shaper: - value of 1 stands for A2N direction, - value of 2 stands for N2A direction. Values 3 and 4 are applicable to Pass-thru Flow Shaper (new in 5.6CC release): - value of 3 stands for N1toN2 direction - value of 4 stands for N2toN1 direction

OBJECT-TYPE

The unique integer index value corresponding to a Quality of Service Shaper. In release 5.6CC the range is extended to 1..16 to support duplicate A2N shapers on a Flow. The duplicate shapers are created under a Flow if network interface of the Flow is ERP Group or Split Horizon Group. In case of multi-cos Flow indices 1..8 represent shapers of COS 0..7 going to Network 1 port; indices 9..16 represent shapers for COS 0..7 going to Network 2 port. In case of single-cos Flow index 1 represents shaper going to Network 1 port; index 9 represents shaper going to Network 2 port.

OBJECT-TYPE

The direction of the Quality of Service Shaper.

OBJECT-TYPE

This object represents the Administrative State of the QOS Shaper.

OBJECT-TYPE

This object represents the Operational State of the QOS Shaper.

OBJECT-TYPE

This object represents the Secondary State of the QOS Shaper.

OBJECT-TYPE

This object represents the Commited Information Rate(CIR) (Lower 32 bits)of a Shaper.

OBJECT-TYPE

This object represents the Commited Burst Size (CBS) of the Shaper.

OBJECT-TYPE

This object represents the Excess Information Rate(EIR) (Lower 32 bits) of a Shaper.

OBJECT-TYPE

This object represents the Excess Burst Size (EBS) of the Shaper.

OBJECT-TYPE

This object represents the Buffer Size of the Shaper.

OBJECT-TYPE

The type of storage configured for this entry.

OBJECT-TYPE

The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of cmQosShaperRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with cmQosShaperRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The cmQosShaperRowStatus object may be modified if the associated instance of this object is equal to active(1).

OBJECT-TYPE

This object provides the COS (Class of Service) value for the QOS Shaper.

OBJECT-TYPE

This object represents the Commited Information Rate(CIR) (Higher 32 bits) of a Shaper.

OBJECT-TYPE

This object represents the Excess Information Rate(EIR) (Higher 32 bits) on the Shaper.

OBJECT-TYPE

This object represents the Soam Commited Information Rate(SOAM-CIR) (Lower 32 bits) of a Shaper.

OBJECT-TYPE

This object represents the Soam Commited Information Rate(SOAM-CIR) (Higher 32 bits) on the Shaper.

OBJECT-TYPE

This object represents the Soam Excess Information Rate(SOAM-EIR) (Lower 32 bits) of a Shaper.

OBJECT-TYPE

This object represents the Soam Excess Information Rate(SOAM-EIR) (Higher 32 bits) on the Shaper.

OBJECT-TYPE

This object represents the Wred green packet min queue threshold value.

OBJECT-TYPE

This object represents the Wred green packet max queue threshold value.

OBJECT-TYPE

This object represents the Wred green packet drop probability.

OBJECT-TYPE

This object represents the Wred yellow packet min queue threshold value.

OBJECT-TYPE

This object represents the Wred yellow packet max queue threshold value.

OBJECT-TYPE

This object represents the Wred yellow packet drop probability.

OBJECT-TYPE

This object specifies the average frame size before fragmentation.

OBJECT-TYPE

This object specifies the wfq weight value.

OBJECT-TYPE

A list of entries corresponding to Ethernet Network Port Facilities for configuration purposes.

OBJECT-TYPE

A conceptual row in the cmEthernetNetPortTable.

OBJECT-TYPE

An integer index value used to uniquely identify this Ethernet Network Port within a card. Note that each Ethernet Network Port is uniquely identified by the indices neIndex, shelfIndex, slotIndex, cmEthernetNetPortIndex.

OBJECT-TYPE

This object has the same value as ifIndex for Ethernet Network Port. An integer index value used to uniquely identify this Ethernet Network Port.

OBJECT-TYPE

Entity Index from ENTITY-MIB for this port.

OBJECT-TYPE

This object represents the Administrative State of the Ethernet Network Port.

OBJECT-TYPE

This object represents the Operational State of the Ethernet Network Port.

OBJECT-TYPE

This object represents the Secondary State of the Ethernet Network Port.

OBJECT-TYPE

This object provides the MTU on the Ethernet Network Port.

OBJECT-TYPE

This object represents the type of Ethernet Media on the Ethernet Network Port.

OBJECT-TYPE

This object allows to configure the speed of the Ethernet Network Port.

OBJECT-TYPE

This object provides the negotiated speed of the Ethernet Network Port.

OBJECT-TYPE

This object allows management of MDIX property on Ethernet Network Port.

OBJECT-TYPE

This object allows enabling/disabling jumbo frames support on the Ethernet Network Port. This object is only applicable for Ethernet Network Port on R3.1CM NTU Card.

OBJECT-TYPE

This object provides the vendor name of the SFP. This is applicable when cmEthernetNetPortMediaType is fiber or coppersfp.

OBJECT-TYPE

This object provides the part number of the SFP. This is applicable when cmEthernetNetPortMediaType is fiber or coppersfp.

OBJECT-TYPE

This object provides the serial number of the SFP. This is applicable when cmEthernetNetPortMediaType is fiber or coppersfp.

OBJECT-TYPE

This object provides the date of manufacture of the SFP. This is applicable when cmEthernetNetPortMediaType is fiber or coppersfp.

OBJECT-TYPE

This object provides the SFP connector value. This is applicable when cmEthernetNetPortMediaType is fiber or coppersfp.

OBJECT-TYPE

This object allows to initiate Etherjack diagnosis on the Ethernet Network Port.

OBJECT-TYPE

This object provides diagnosis results for the cable Pair 1 on Ethernet Network Port.

OBJECT-TYPE

This object provides diagnosis results for the cable Pair 2 on Ethernet Network Port.

OBJECT-TYPE

This object provides diagnosis results for the cable Pair 3 on Ethernet Network Port.

OBJECT-TYPE

This object provides diagnosis results for the cable Pair 4 on Ethernet Network Port.

OBJECT-TYPE

This object provides auto negotiation results of the diagnosis test on Ethernet Network Port.

OBJECT-TYPE

This object provides port loopback results of the diagnosis test on Ethernet Network Port.

OBJECT-TYPE

This object provides remote EFM loopback results of the diagnosis test on Ethernet Network Port.

OBJECT-TYPE

This object provides results of the diagnosis test in string form on Ethernet Network Port.

OBJECT-TYPE

This object provides the current status of the diagnosis test on Ethernet Access Port.

OBJECT-TYPE

This object provides the time when diagnosis test was last executed.

OBJECT-TYPE

This object allows to initiate loopbacks on on the Ethernet Network Port.

OBJECT-TYPE

This object provides status of the current loopback on the Ethernet Network Port.

OBJECT-TYPE

This object allows to specify time for timed-loopbacks on on the Ethernet Network Port.

OBJECT-TYPE

This object allows to specify whether or not the loopbacked frame will have the Source Address and Destination Address swapped.

OBJECT-TYPE

This object allows specification of the outer VLANs to be looped back when port is in vlan(terminal/facility) loopback configuration. Only 3 VLANs can be specified for vlan loopback. The various bit positions are: 1 Outer VLAN 1 Loopback Enabled 2 Outer VLAN 2 Loopback Enabled 4 Outer VLAN 3 Loopback Enabled Value of 0 means that no VLANs are enabled.

OBJECT-TYPE

This object allows specification of the outer VLAN 1 to be looped back when port is in vlan(terminal/facility) loopback configuration. This is valid only if the corresponding bit in cmEthernetNetPortOuterVlanLoopbackMask is set. The value to be specified should be in the form X-Y where X is the VLAN Id and Y is the VLAN Priority. If Y is specified as a *, all Priorities (0 to 7) are looped back.

OBJECT-TYPE

This object allows specification of the outer VLAN 2 to be looped back when port is in vlan(terminal/facility) loopback configuration. This is valid only if the corresponding bit in cmEthernetNetPortOuterVlanLoopbackMask is set. The value to be specified should be in the form X-Y where X is the VLAN Id and Y is the VLAN Priority. If Y is specified as a *, all Priorities (0 to 7) are looped back.

OBJECT-TYPE

This object allows specification of the outer VLAN 3 to be looped back when port is in vlan(terminal/facility) loopback configuration. This is valid only if the corresponding bit in cmEthernetNetPortOuterVlanLoopbackMask is set. The value to be specified should be in the form X-Y where X is the VLAN Id and Y is the VLAN Priority. If Y is specified as a *, all Priorities (0 to 7) are looped back.

OBJECT-TYPE

This object allows specification of the inner VLANs to be looped back when port is in vlan(terminal/facility) loopback configuration. Only 3 VLANs can be specified for vlan loopback. The various bit positions are: 1 Inner VLAN 1 Loopback Enabled 2 Inner VLAN 2 Loopback Enabled 4 Inner VLAN 3 Loopback Enabled Value of 0 means that no VLANs are enabled.

OBJECT-TYPE

This object allows specification of the inner VLAN 1 to be looped back when port is in vlan(terminal/facility) loopback configuration. This is valid only if the corresponding bit in cmEthernetNetPortInnerVlanLoopbackMask is set. The value to be specified should be in the form X-Y where X is the VLAN Id and Y is the VLAN Priority. If Y is specified as a *, all Priorities (0 to 7) are looped back.

OBJECT-TYPE

This object allows specification of the inner VLAN 2 to be looped back when port is in vlan(terminal/facility) loopback configuration. This is valid only if the corresponding bit in cmEthernetNetPortInnerVlanLoopbackMask is set. The value to be specified should be in the form X-Y where X is the VLAN Id and Y is the VLAN Priority. If Y is specified as a *, all Priorities (0 to 7) are looped back.

OBJECT-TYPE

This object allows specification of the inner VLAN 3 to be looped back when port is in vlan(terminal/facility) loopback configuration. This is valid only if the corresponding bit in cmEthernetNetPortInnerVlanLoopbackMask is set. The value to be specified should be in the form X-Y where X is the VLAN Id and Y is the VLAN Priority. If Y is specified as a *, all Priorities (0 to 7) are looped back.

OBJECT-TYPE

This object allows enabling/disabling link loss forwarding on the Ethernet Network Port.

OBJECT-TYPE

This object allows definition of the link loss forwarding signalling type. This is applicable only if cmEthernetNetPortLinkLossFwdEnabled is enabled. This object is only valid for FSP150CM Release 3.1. This object is deprecated henceforth. Link Loss signalling will be supported using the object cmEthernetAccPortLinkLossFwdTxActionType.

OBJECT-TYPE

This object allows definition of the link loss forwarding trigger types. This is applicable only if cmEthernetAccPortLinkLossFwdEnabled is enabled.

OBJECT-TYPE

This object allows specification of the delay between detection of link loss and signalling of link loss forwarding. Time specified is in seconds.

OBJECT-TYPE

This object provides the link loss forwarding status indicating if link loss forwarding is currently being signaled via the port.

OBJECT-TYPE

This object provides the indication of a link partners ability to support link loss forwarding via EFM, i.e. from received organization specific OAMPDUs.

OBJECT-TYPE

This object allows configuration of the Local Link Id on Ethernet Network port.

OBJECT-TYPE

This object allows enabling/disabling Remote Link Ids on Ethernet Network port. By setting the appropriate bit positions, the Ethernet Network port is able to distinguish the remote side client ports from the Remote Link Down PDUs coming from remote end.

OBJECT-TYPE

OAM Id. This is unique EFM OAM sublayer port id.

OBJECT-TYPE

Ethernet Network Port's EFM OAM Administrative Disposition. This object is applicable only for FSP150CM Release 3.1. This object is deprecated henceforth. With FSP150CC Release 4.1, this property is managed using the Control Protocol Disposition tables.

OBJECT-TYPE

Ethernet Network Port's OAM discovery state.

OBJECT-TYPE

This object allows specification of whether the Ethernet Network Port supports sending variable response OAMPDUs.

OBJECT-TYPE

This object allows specification of whether the Ethernet Network Port supports interpreting Link Events.

OBJECT-TYPE

This object allows specification of whether the Ethernet Network Port is capable of OAM remote loopback mode.

OBJECT-TYPE

This object allows specification of whether the Ethernet Network Port is capable of sending OAMPDUs when the receive path is non-operational.

OBJECT-TYPE

This object represents the largest OAMPDU, in octets, supported by the Ethernet Network Port. This value is compared to the remote Maximum PDU Size and the smaller of the two is used.

OBJECT-TYPE

This object allows to configure the OAM sublayer entity in either Active or Passive mode.

OBJECT-TYPE

This object allows retrieval of the Remote Mac Address.

OBJECT-TYPE

This object allows retrieval of whether the remote OAM entity supports sending variable response OAMPDUs.

OBJECT-TYPE

This object allows retrieval of whether the remote OAM entity supports interpreting Link Events.

OBJECT-TYPE

This object allows retrieval of whether the remote OAM entity supports OAM remote loopback mode.

OBJECT-TYPE

This object allows retrieval of whether the remote OAM entity is capable of sending OAMPDUs when the receive path is non-operational.

OBJECT-TYPE

This object allows retrieval of the remote OAM entity maximum OAMPDU size.

OBJECT-TYPE

This object allows to retrieve whether the remote OAM sublayer entity is either in Active or Passive mode.

OBJECT-TYPE

This object allows enabling/disabling receive pause frames on Ethernet Network port. This object is not applicable for FSP150CC Release 4.1 products.

OBJECT-TYPE

This object allows enabling/disabling transmit pause frames on Ethernet Network port. This object is not applicable for FSP150CC Release 4.1 products.

OBJECT-TYPE

This object allows specification of the Acceptable Frame Policy on Ethernet Network port. Users can specify whether the port supports only tagged frames, only untagged frames or both tagged and untagged frames. This object is not applicable for FSP150CC Release 4.1 products.

OBJECT-TYPE

This object provides the current MDIX status of the Ethernet Network port.

OBJECT-TYPE

This object provides the SFP Reach in meters. This is applicable when cmEthernetNetPortMediaType is fiber or coppersfp.

OBJECT-TYPE

This object provides the SFP Laser Wave Length in nano meters. This is applicable only when cmEthernetNetPortMediaType is fiber.

OBJECT-TYPE

This object provides the SFP Media Type. This is applicable when cmEthernetNetPortMediaType is fiber or coppersfp.

OBJECT-TYPE

This object allows to manage the EFM OAM on Ethernet Network Port.

OBJECT-TYPE

This object provides the EFM OAM Admin State.

OBJECT-TYPE

This object allows to manage the Network Port Shaping. When enabled, values in cmEthernetNetPortShapedSpeedLo and cmEthernetNetPortShapedSpeedHi are applicable.

OBJECT-TYPE

This object allows to specify the lower 32 bits of the Network Port Shaped speed. This value is applicable when cmEthernetNetPortShapingEnabled is enabled.

OBJECT-TYPE

This object allows to specify the higher 32 bits of the Network Port Shaped speed. This value is applicable when cmEthernetNetPortShapingEnabled is enabled.

OBJECT-TYPE

This object allows to specify the Q-in-Q Ether Type on the Network Port. Setting this value to 0 will disable the Q-in-Q override on the Network Port.

OBJECT-TYPE

This object allows to specify the Network Port's behavior when link loss forwarding trigger events occur on the Access Port.

OBJECT-TYPE

This object provides the received Remote Link IDs in EFM RLD messages on the Network Port.

OBJECT-TYPE

This object allows to enable or disable the automatic Cable Diagnostic tests when the cable is removed from the port.

OBJECT-TYPE

This object allows to specify whether the Ethernet Network Port can be enabled/disabled for Synchronous Ethernet. This object is only applicable for Synchronous Ethernet capable ports. When enabled, on receive side -port can extract the frequency of its input signal and pass the recovered clock to the system clock -port processes the ESMC(Ethernet Synchronization Messaging Channel) and extracts the QL (when also QL enabled) -port is eligible to be selected as a system clock reference When enabled, on transmit side -port's transmit clock is locked to the system clock -port generates an ESMC to generate a QL (when also QL enabled) When disabled, on receive side, -port does not pass the recovered clock to the system clock -port does not process the ESMC (if present) -port is not eligible to be selected as a system clock reference When disabled, on transmit side -port's output frequency may be synchronized to the system clock -port does not generate an ESMC.

OBJECT-TYPE

This object allows to specify whether the Ethernet Network Port can be enabled/disabled for QL Mode. This object is only applicable for Synchronous Ethernet capable ports, when cmEthernetNetPortQLModeEnabled is set to true. When enabled, on receive side -port shall PEER the SSM (Sync Status Messages) slow protocol PDUs and take appropriate action When enabled, on transmit side -port shall periodically (once a second) transmit QL TLV information PDUs When disabled, on receive side, -port shall terminate and discard any SSM slow protocol PDUs When disabled, on transmit side -port shall not transmit any SSM slow protocol PDUs.

OBJECT-TYPE

This object allows to specify the expected QL when the Ethernet Network Port is enabled for QL Mode. This object is only applicable for Synchronous Ethernet capable ports, when cmEthernetNetPortQLModeEnabled is set to true. This object allows the user to set a minimum expected received Quality Level on the port. The valid values depend upon the SYNC entity's Network Clock Type. A value of None represents that a minimum Quality Level is not expected. The default value shall be None.

OBJECT-TYPE

This object allows to specify the assumed QL on the Ethernet Network Port. This object is only applicable for Synchronous Ethernet capable ports. The Assumed QL is only meaningful if the Network Clock Type (see fsp150cm-sync.mib) is option1 and the port's QL Mode is disabled and the port is being used as an input reference source. Under these conditions, the specified QL value is assumed to be the Quality Level of the non-failed reference.

OBJECT-TYPE

This object provides the Received QL value for the Ethernet port. If the Ethernet port's QL Mode is disabled, then the received QL value is not applicable.This object is only applicable for Synchronous Ethernet capable ports.

OBJECT-TYPE

This object provides the Transmitted QL value for the Ethernet port. If the Ethernet port's QL Mode is disabled, then the received QL value is not applicable. This object is only applicable for Synchronous Ethernet capable ports.

OBJECT-TYPE

This object provides the Priority Mapping Mode used for classification of frames.

OBJECT-TYPE

This is a port level control to reset the DEI (Drop Eligibility Indicator) bit in the S-Tag, if the downstream equipment supports S-Tag TPID (EtherType) but cannot handle DEI bit set. In the receive direction, it uses the S-TAG DEI when enabled, else ignores it. The following comment is NOT relevant to OSA8.1.1, since this object is still supported by OSA8.1.1. The object has been deprecated. The respective configuration should be managed by following objects: cmEthernetNetPortRxDeiAction, cmEthernetNetPortTxDeiAction, cmEthernetNetPortRxDeiOuterTagType, cmEthernetNetPortTxDeiOuterTagType.

OBJECT-TYPE

This is a port level control that specifies the mode of drop eligibility encoding in PCP bits of the VLAN tag.

OBJECT-TYPE

This object allows the SNMP user to manage the Priority Code Point (PCP) Drop Eligibility Pairs. When the cmEthernetNetPortPcpDEEncType is of type 7p1d, 6p2d, 5p3d, the cmNetPortPcpDEPairTable can be used to specify alternate pairs of priorities to specify drop eligibility/ ineligibility.

OBJECT-TYPE

This object allows retrieval of the Remote Mac Address, when the port is peering using SSM.

OBJECT-TYPE

This object allows to specify the PHY type of 10G Ethernet Port. 10G ports can operate in LAN-PHY or WAN-PHY mode. The default mode is LAN-PHY and port rate in this mode is 10Gbps. In WAN-PHY mode the port rate is 9.29Gbps. This attribute is only applicable for ports configured to work at speed-10G-full. For other speeds the value of this object must be 'not-applicable' and cannot be changed.

OBJECT-TYPE

This object allows to Enable/Disable the Net Port Source MAC Address frame matching criteria for all streams. Not applicable for: efm-oam-remote, efm-oam-remote-timed.

OBJECT-TYPE

This object allows to Enable/Disable the Net Port Destination MAC Address frame matching criteria for all streams. Not applicable for: efm-oam-remote, efm-oam-remote-timed.

OBJECT-TYPE

This object allows to set Net Port Source MAC Address for frame matching when Net Port Source MAC Control is enabled.

OBJECT-TYPE

This object allows to set Net Port Destination MAC Address for frame matching when Net Port Destination MAC Control is enabled.

OBJECT-TYPE

This object allows frame blocking when loopback is active. - True: Blocks frames in the non-loopback direction that match the PORT or VLAN received in the non-loopback direction. Discards frames in the loopback direction that match the PORT or VLAN, but do not match the MAC address criteria, - False: No blocking of frames.

OBJECT-TYPE

This object allows to specify the Receive DEI Action.

OBJECT-TYPE

This object allows to specify the Transmit DEI Action.

OBJECT-TYPE

This object allows to specify the Receive DEI Outer Tag Type.

OBJECT-TYPE

This object allows to specify the Transmit DEI Outer Tag Type.

OBJECT-TYPE

Channel number of WDM tunable XFP setting.

OBJECT-TYPE

Channel number of WDM tunable XFP setting.

OBJECT-TYPE

Channel number of WDM tunable XFP setting.

OBJECT-TYPE

This object provides the auto selected Ethernet Media of the Ethernet Network Port.

OBJECT-TYPE

This object allows to Enable/Disable the Low Latency Queuing on the Ethernet Network Port.

OBJECT-TYPE

This object describes the diagnose mac address for SAT, ECPA, JDSU, Loopback with Override SA etc.

OBJECT-TYPE

Indicates the VLAN tag to use for PCP Priority to COS mapping when the port Priority Map Mode is 802.1p. Supported values are inner-vlantag and outer-vlantag. This attribute is only applicable on products when Flowpoint Model is supported. inner-vlantag: The inner VLAN tag PCP Priority of a frame is used for ingress COS mapping. A frame with no inner VLAN tag (untagged or single-tagged) will have a COS equal to the default COS of the port. outer-vlantag: The outer VLAN tag PCP Priority of a frame is used for ingress COS mapping. A frame with no outer VLAN tag (untagged) will have a COS equal to the default COS of the port. This attribute has been deprecated and is not supported. Now, the Priority Map Mode indicates whether it is inner or outer. Use priomap-8021p(4) for outer and priomap-8021p-inner(5) for inner.

OBJECT-TYPE

The COS assigned to a frame that does not have a valid COS identifier for the Priority Map Mode of the port. This attribute is only applicable on products when Flowpoint Model is supported. This value is assigned to a frame received on a port when: - the cmEthernetNetPortPrioMapMode=priomap-8021p, ingressCOSPriority=inner-vlantag; and the frame is untagged - the cmEthernetNetPortPrioMapMode=priomap-8021p, ingressCOSPriority=inner-vlantag; and the frame has a single VLAN tag - the cmEthernetNetPortPrioMapMode=priomap-8021p, ingressCOSPriority=outer-vlantag; and the frame is untagged - the cmEthernetNetPortPrioMapMode=priomap-dscp; and the frame does not have an IP ethertype - the cmEthernetNetPortPrioMapMode=priomap-tos; and the frame does not have an IP ethertype. This attribute has been deprecated and is not supported. The Default COS is determined from the flowpoint's associated Priority Mapping Profle.

OBJECT-TYPE

The Traffic Management connection model available for the port. - accessFlow: NID Traffic Connection model. - flowpoint: Multipoint and Aggregation Traffic Connection model.

OBJECT-TYPE

This object describes the shaper BW whether independent.

OBJECT-TYPE

This is a port level control that specifies the mode of drop eligibility encoding in exp bits of the VLAN tag.

OBJECT-TYPE

This object allows the SNMP user to manage the Priority Code Point (PCP) Drop Eligibility Pairs. When the cmEthernetNetPortExpDEEncType is of type 7p1d, 6p2d, 5p3d, the cmNetPortExpDEPairTable can be used to specify alternate pairs of priorities to specify drop eligibility/ ineligibility.

OBJECT-TYPE

This is a port level control that specifies the mode of drop eligibility encoding in Ip Prec bits of the VLAN tag.

OBJECT-TYPE

This object allows the SNMP user to manage the Ip Prec Drop Eligibility Pairs. When the cmEthernetNetPortIpPrecDEEncType is of type 7p1d, 6p2d, 5p3d, the cmNetPortIpPrecDEPairTable can be used to specify alternate pairs of priorities to specify drop eligibility/ ineligibility.

OBJECT-TYPE

This is a port level control the mode of drop eligibility encoding in PCP bits of the VLAN tag in encapsulation header.

OBJECT-TYPE

This object allows the SNMP user to manage the Priority Code Point (PCP) Drop Eligibility Pairs. When the cmEthernetNetPortEncapPcpDEEncodingType is of type 7p1d, 6p2d, 5p3d, the cmNetPortEncapPcpDEPairTable can be used to specify alternate pairs of priorities to specify drop eligibility/ ineligibility.

OBJECT-TYPE

This object is applicable when there is jdsu l3 loopback.

OBJECT-TYPE

This object is used to specify the wfq segmentation COS value.

OBJECT-TYPE

This object is used to specify the wfq group COS value.

OBJECT-TYPE

This object is used to specify the wfq group eir low 32 bits value.

OBJECT-TYPE

This object is used to specify the wfq group eir high 32 bits value.

OBJECT-TYPE

Allows enabling/disabling of silent start.

OBJECT-TYPE

This object provides the SFP Link Length. This is applicable only when cmEthernetTrafficPortMediaType is fiber or coppersfp.

OBJECT-TYPE

This object allows enabling/disabling of Outer Tag TPID override. When enabled, values in Outer Tag TPID is applicable on egress Ethernet Network Port.

OBJECT-TYPE

This object allows to specify the egress Outer Tag TPID on the Ethernet Network Port.

OBJECT-TYPE

This object provides the official name of the SFP.

OBJECT-TYPE

This object provides the hardware revision of the SFP.

OBJECT-TYPE

This object allows enabling/disabling of Persistent Loopback Control. The loopback configuration parameters do not survive restart as typically maintenance actions are not persist. Setting this attribute to true shall persist the loopback configuration parameters. When it is set to false the loopback configuration parameters shall not survive a restart.

OBJECT-TYPE

Control that enables/disables Test Reflector IPv4 Address to be used for Test Reflector IP Interface.

OBJECT-TYPE

This is the Test Reflector Interface IPv4 address.

OBJECT-TYPE

Control that enables/disables Test Reflector IPv6 Address to be used for Test Reflector IP Interface.

OBJECT-TYPE

This is the Test Reflector Interface IPv6 address.

OBJECT-TYPE

This object provides the SFP identifier value.

OBJECT-TYPE

A list of entries corresponding to Ethernet Network Port Control Protocol Disposition. This table is only applicable for FSP150CM Hub Shelf Release 3.x.

OBJECT-TYPE

A conceptual row in the cmEthernetNetPortCpdTable. These entries represent a Control Protocol Disposition filtering criteria on the Ethernet Network Port.

OBJECT-TYPE

An arbitrary integer index value used to uniquely identify this CPD Service Entry.

OBJECT-TYPE

This enables specification of type of CPD Filter.

OBJECT-TYPE

This provides description of CPD Filter.

OBJECT-TYPE

This enables specification of disposion type of CPD Filter.

OBJECT-TYPE

This enables provides the Filter MAC Address to match.

OBJECT-TYPE

This enables provides the Filter MAC Address Mask to match.

OBJECT-TYPE

This enables provides the Filter Ethertype to match.

OBJECT-TYPE

This enables provides the Filter Ethertype Mask to match.

OBJECT-TYPE

This enables provides the Filter Subtype to match.

OBJECT-TYPE

This enables provides the Filter Subtype Mask to match.

OBJECT-TYPE

A list of entries corresponding to Ethernet Management Port Facilities for configuration purposes.

OBJECT-TYPE

A conceptual row in the cmEthernetMgmtPortTable.

OBJECT-TYPE

An integer index value used to uniquely identify this Ethernet Management Port within a card. Note that each Ethernet Management Port is uniquely identified by the indices neIndex, shelfIndex, slotIndex, cmEthernetMgmtPortIndex.

OBJECT-TYPE

Entity Index from ENTITY-MIB for this port.

OBJECT-TYPE

This object represents the Administrative State of the Ethernet Management Port.

OBJECT-TYPE

This object represents the Operational State of the Ethernet Management Port.

OBJECT-TYPE

This object represents the Secondary State of the Ethernet Management Port.

OBJECT-TYPE

This object provides the MTU on the Ethernet Management Port.

OBJECT-TYPE

This object allows to configure the speed of the Ethernet Management Port.

OBJECT-TYPE

This object provides the negotiated speed of the Ethernet Management Port.

OBJECT-TYPE

This object allows management of MDIX property on Ethernet Management Port.

OBJECT-TYPE

This object provides the current MDIX status of the Ethernet Management port.

OBJECT-TYPE

This object represents the type of Ethernet Media on the Ethernet Management Port.

OBJECT-TYPE

A list of entries corresponding to Ethernet Priority Mappings in multi Class of Service (COS) mode. This table is applicable only when the Access Port is in connection-oriented evpl mode.

OBJECT-TYPE

A conceptual row in the cmPrioMapTable.

OBJECT-TYPE

The integer index value corresponding to a priority value based on the cmEthernetAccPortPrioMapMode. In case of TOS and 8021P, valid indices are 1 to 8, in case of DSCP, valid indices are 1 to 64.

OBJECT-TYPE

The integer index value corresponding to a priority value based on the cmEthernetAccPortPrioMapMode. In case of TOS and 8021P, valid indices are 0 to 7, in case of DSCP, valid indices are 0 to 63.

OBJECT-TYPE

This allows specification of whether the priority of incoming X-TAG should be swapped with cmPrioMapXTagPriority.

OBJECT-TYPE

This allows specification of the VLAN priority that will replace the incoming X-TAG's priority. This is applicable with cmPrioMapXTagControl as 'swap'.

OBJECT-TYPE

This allows specification of the COS Priority, i.e. this helps in determining the appropriate COS Policer for the Flow.

OBJECT-TYPE

This allows specification of the VLAN priority that will replace the outgoing (A2N direction) outer-tag's priority. Note that, each flow participates or not in outer-tag priority mapping, using the object 'cmFlowOuterTagPrioEnabled'.

OBJECT-TYPE

This allows specification of the VLAN priority that will replace the outgoing (A2N direction) inner-tag's (i.e. second tag) priority. Note that, each flow participates or not in inner-tag priority mapping, using the object 'cmFlowInnerTagPrioEnabled'.

OBJECT-TYPE

A list of entries corresponding to Ethernet Quality of Service Policer for configuration purposes.

OBJECT-TYPE

A conceptual row in the cmQosFlowPolicerTable. These entries represent a Quality of Service Policer.

OBJECT-TYPE

The unique index value corresponding to a Quality of Service Policer's direction. Values 1 and 2 are applicable to the Access Flow Policer - value of 1 stands for A2N direction, - value of 2 stands for N2A direction. Values 3 and 4 are applicable to Pass-thru Flow Policer (new in 5.6CC release): - value of 3 stands for N1toN2 direction - value of 4 stands for N2toN1 direction

OBJECT-TYPE

The Policer Index that represents the COS level. This is applicable in case of a Multi COS flow. Index 1 represents COS 0; Index 2 represents COS 1 and so on. In release 5.6CC the range is extended to 1..16 to support duplicate N2A policers on a Flow. The duplicate policers are created under a Flow if network interface of the Flow is ERP Group or Split Horizon Group. In case of multi-cos Flow indices 1..8 represent policers of COS 0..7 going from Network 1 port; indices 9..16 represent policers for COS 0..7 going from Network 2 port. In case of single-cos Flow index 1 represents policer going from Network 1 port; index 9 represents policer going from Network 2 port.

OBJECT-TYPE

This object is allows specification of Policer direction as 'a2n' or 'n2a'.

OBJECT-TYPE

This object represents the Administrative State of the QOS Flow Policer.

OBJECT-TYPE

This object represents the Operational State of the QOS Flow Policer.

OBJECT-TYPE

This object represents the Secondary State of the QOS Flow Policer.

OBJECT-TYPE

This object allows specification of the Commited Information Rate(CIR) on Policer. This represents the lower 32 bits of the CIR.

OBJECT-TYPE

This object allows specification of the Commited Information Rate(CIR) on Policer. This represents the upper 32 bits of the CIR.

OBJECT-TYPE

This object allows specification of the Excess Information Rate(EIR) on the Policer. This represents the lower 32 bits of the EIR.

OBJECT-TYPE

This object allows specification of the Excess Information Rate(EIR) on the Policer. This represents the upper 32 bits of the EIR.

OBJECT-TYPE

This object allows specification of the Commited Burst Size (CBS) on Policer.

OBJECT-TYPE

This object allows specification of the Excess Burst Size (EBS) on the Policer.

OBJECT-TYPE

This object allows specification of Policer algorithm as 'srTCM' (Single Rate Triple Color Marking) or 'trTCM' (Two Rate Triple Color Marking).

OBJECT-TYPE

This object allows specification of Policer Color Mode as 'color-aware' or 'color-blind'.

OBJECT-TYPE

This object allows specification of Policer Color Marking Flag. The policer will set/clear the DEI (Drop Eligibility Indication) bit of the frame on an S-TAG if this flag is enabled. This object is not supported - setting any value will not have effect on the System.

OBJECT-TYPE

This object allows specification of Policer Coupling Flag. When coupling is enabled, tokens that would normally be added to the C-bucket are passed to the E-bucket only once the CIR bucket has reached its CBS level. Therefore under this condition the E-bucket is being filled at the rate of CIR + EIR. Normally the long term average of frames declared yellow is bounded by the EIR. Coupling is a function to allow the long term average of frames declared yellow to be bounded by CIR + EIR. This allows a higher volume of yellow frames to be delivered/received if the arrival of green marked frames is low. Tokens from the E-bucket do NOT get passed to the C-bucket once the EBS level has been reached. Enabling coupling in combination with a provisioned EIR of 0 allows for a single rate three color marking (srTCM) algorithm to be established. In this situation the E-bucket is filled at the CIR rate in the case the C-bucket is filled to its CBS level.

OBJECT-TYPE

This object allows specification of the QOS Shaper associated with this Policer. Multiple Policers can map to single Shaper. The corresponding row with the specified QOS value must exist in cmQosShaperTable when this value is specified.

OBJECT-TYPE

The type of storage configured for this entry.

OBJECT-TYPE

The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of cmQosFlowPolicerRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with cmQosFlowPolicerRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The cmQosFlowPolicerRowStatus object may be modified if the associated instance of this object is equal to active(1).

OBJECT-TYPE

This object allows specification of the Commited Information Rate(CIR) MAX on Policer. This represents the high 32 bits.

OBJECT-TYPE

This object allows specification of the Commited Information Rate(CIR) MAX on Policer. This represents the lower 32 bits.

OBJECT-TYPE

This object allows specification of the Excess Information Rate(EIR) MAX on the Policer. This represents the high 32 bits.

OBJECT-TYPE

This object allows specification of the Excess Information Rate(EIR) MAX on the Policer. This represents the lower 32 bits.

OBJECT-TYPE

This object allows specification of envelope object.

OBJECT-TYPE

This object allows specification of rank value.

OBJECT-TYPE

This object describes whether the policing is enabled.

OBJECT-TYPE

A list of entries corresponding to Ethernet Access Port Quality of Service Shaper for configuration purposes. These shapers can be managed when the Access Port is in evpl mode and are relevant for traffic in the network to access direction.

OBJECT-TYPE

A conceptual row in the cmAccPortQosShaperTable. These entries represent a Quality of Service Shaper.

OBJECT-TYPE

The unique integer index value corresponding to a Quality of Service Shaper.

OBJECT-TYPE

The direction of the Quality of Service Shaper.

OBJECT-TYPE

This object represents the Administrative State of the QOS Shaper.

OBJECT-TYPE

This object represents the Operational State of the QOS Shaper.

OBJECT-TYPE

This object represents the Secondary State of the QOS Shaper.

OBJECT-TYPE

This object represents the Commited Information Rate(CIR) (Lower 32 bits)of a Shaper.

OBJECT-TYPE

This object represents the Commited Information Rate(CIR) (Higher 32 bits) of a Shaper.

OBJECT-TYPE

This object represents the Excess Information Rate(EIR) (Higher 32 bits) on the Shaper.

OBJECT-TYPE

This object represents the Excess Information Rate(EIR) (Higher 32 bits) on the Shaper.

OBJECT-TYPE

This object represents the Commited Burst Size (CBS) of the Shaper.

OBJECT-TYPE

This object represents the Excess Burst Size (EBS) of the Shaper.

OBJECT-TYPE

This object represents the Buffer Size of the Shaper.

OBJECT-TYPE

This object provides the COS (Class of Service) value for the QOS Shaper.

OBJECT-TYPE

This object represents the Soam Commited Information Rate(SOAM-CIR) (Lower 32 bits)of a Shaper.

OBJECT-TYPE

This object represents the Soam Commited Information Rate(SOAM-CIR) (Higher 32 bits) of a Shaper.

OBJECT-TYPE

This object represents the Soam Excess Information Rate(SOAM-EIR) (Higher 32 bits) on the Shaper.

OBJECT-TYPE

This object represents the Soam Excess Information Rate(SOAM-EIR) (Higher 32 bits) on the Shaper.

OBJECT-TYPE

This object represents the Wred green packet min queue threshold value.

OBJECT-TYPE

This object represents the Wred green packet max queue threshold value.

OBJECT-TYPE

This object represents the Wred green packet drop probability.

OBJECT-TYPE

This object represents the Wred yellow packet min queue threshold value.

OBJECT-TYPE

This object represents the Wred yellow packet max queue threshold value.

OBJECT-TYPE

This object represents the Wred yellow packet drop probability.

OBJECT-TYPE

This object specifies the average frame size before fragmentation.

OBJECT-TYPE

This object specifies the wfq weight value.

OBJECT-TYPE

A list of entries corresponding to Ethernet Access Port Control Protocol Disposition (CPD) V2. This support of CPD is provided on the GE206/GE201 device.

OBJECT-TYPE

A conceptual row in the cmEthernetAccPortCpdV2Table. These entries represent a Control Protocol Disposition filtering criteria on the Ethernet Access Port.

OBJECT-TYPE

Unique Index value to access the CPD row.

OBJECT-TYPE

Deprecated - each Cisco protocol has its own disposition. Control Protocol Disposition for Cisco Group. This includes ISL, PAGP, UDLD, CDP, VTP, DTP, PSVTP+, UplinkFast, VLAN Bridge, L2PT. Note that a specific protocol filter overrides the group setting.

OBJECT-TYPE

Control Protocol Disposition for ISL (Inter Switch Link). MAC Address (01:00:0C:00:00:00).

OBJECT-TYPE

Control Protocol Disposition for PAGP (Port Aggregation Protocol). MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x104).

OBJECT-TYPE

Control Protocol Disposition for UDLD (Unidirectional Link Detection). MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x111).

OBJECT-TYPE

Control Protocol Disposition for CDP (Cisco Discovery Protocol). MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x2000).

OBJECT-TYPE

Control Protocol Disposition for VTP (VLAN Trunking Protocol). MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x2003).

OBJECT-TYPE

Control Protocol Disposition for DTP (Dynamic Trunking). MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x2004).

OBJECT-TYPE

Control Protocol Disposition for Spanning Tree PVSTP+. MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x10B).

OBJECT-TYPE

Control Protocol Disposition for STP UplinkFast. MAC Address (01:00:0C:CD:CD:CD), Ethertype(0x200A).

OBJECT-TYPE

Control Protocol Disposition for VLAN Bridge. MAC Address (01:00:0C:CD:CD:CE), Ethertype(0x10C).

OBJECT-TYPE

Control Protocol Disposition for Layer 2 Protocol Tunnelling(L2PT). MAC Address (01:00:0C:CD:CD:D0).

OBJECT-TYPE

Deprecated - individual dispositions available for each MAC. Bridge Group Control Protocol Disposition Type. This includes BPDU, PAUSE (IEEE 802.3x Flow Control), LACP (Link Aggregation), LACP Marker (Marker), EFM OAM (IEEE 802.3 ah) and IEEE 802.1x Port Authentication, besides reserved MAC addresses from 01:80:C2:00:00:04 thru 01:80:C2:00:00:0F.

OBJECT-TYPE

Control Protocol Disposition for IEEE Spanning Tree(STP), MSTP (Multiple Spanning Tree) and RSTP (Rapid Reconfiguration of Spanning Tree). MAC Address (01:80:C2:00:00:00).

OBJECT-TYPE

Control Protocol Disposition for IEEE 802.3x Flow Control (PAUSE frames).

OBJECT-TYPE

Control Protocol Disposition for 802.3ad Link Aggregation Protocol. MAC Address (01:80:C2:00:00:03), Ethertype (0x8809), Subtype(01).

OBJECT-TYPE

Control Protocol Disposition for IEEE 802.3ad Marker Protocol. MAC Address (01:80:C2:00:00:03), Ethertype (0x8809), Subtype(02).

OBJECT-TYPE

Control Protocol Disposition for IEEE 802.3ah EFM OAM. MAC Address (01:80:C2:00:00:03), Ethertype (0x8809), Subtype(03).

OBJECT-TYPE

Control Protocol Disposition for Sync Status Messages. MAC Address (01:80:C2:00:00:02), Ethertype (0x19A7), Subtype(0A).

OBJECT-TYPE

Control Protocol Disposition for IEEE 802.1x Protocol. MAC Address (01:80:C2:00:00:03), Ethertype (0x888E).

OBJECT-TYPE

Deprecated - individual dispositions available for each MAC. Control Protocol Disposition for Range of MAC Addresses from 01:80:C2:00:00:04 to 01:80:C2:00:00:0F.

OBJECT-TYPE

Control Protocol Disposition for IEEE 802.1d LAN Bridge Managment. MAC Address (01:80:C2:00:00:10).

OBJECT-TYPE

Deprecated - each GARP Group protocol has its own disposition. Group Disposition type which includes GMRP, GVRP and MAC Address from range 01:80:C2:00:00:20 to 01:80:C2:00:00:2F.

OBJECT-TYPE

Control Protocol Disposition for GARP Multicast Registration Protocol. MAC Address (01:80:C2:00:00:20).

OBJECT-TYPE

Control Protocol Disposition for GARP VLAN Registration Protocol. MAC Address (01:80:C2:00:00:21).

OBJECT-TYPE

Group Disposition type which includes GARP Reserved MAC Address from range 01:80:C2:00:00:22 to 01:80:C2:00:00:2F.

OBJECT-TYPE

Deprecated - each LLDP MAC protocol has its own disposition. LLDP (Link Layer Discovery Protocol) Disposition type. MAC Address 01:80:C2:00:00:0e, 01:80:C2:00:00:03, or 01:80:C2:00:00:00.

OBJECT-TYPE

ELMI (Ethernet Local Management Interface) Disposition type. MAC Address 01:80:C2:00:00:07 and EtherType of 0x88EE.

OBJECT-TYPE

Configurable Layer 2 Protocol Tunneling MAC Address. For protocols STP, CDP and VTP, with control protocol disposition as pass-thru-l2pt, this configured MAC address replaces the DA, upon encapsulation. For decapsulation, protocol signature and this configured MAC address are matched and the MAC address is replaced with the protocol's inferred MAC address.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:00 Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:01 Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:02 Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:03 Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:04 Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:05 Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:06 Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:07 Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:08 Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:09 Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:0A Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:0B Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:0C Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:0D Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:0E Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:0F Disposition type.

OBJECT-TYPE

LLDP (Link Layer Discovery Protocol) Nearest Bridge Disposition type.

OBJECT-TYPE

LLDP (Link Layer Discovery Protocol) Non-TPMR Bridge Disposition type.

OBJECT-TYPE

LLDP (Link Layer Discovery Protocol) Customer Bridge Disposition type.

OBJECT-TYPE

PTP untagged frame Disposition type.

OBJECT-TYPE

PTP tagged frame Disposition type.

OBJECT-TYPE

A list of entries corresponding to Ethernet Flow Control Protocol Disposition V2. This table is supported for the GE206/GE201 devices.

OBJECT-TYPE

A conceptual row in the cmFlowCpdV2Table. These entries represent a Control Protocol Disposition filtering criteria on the Ethernet Flow.

OBJECT-TYPE

Unique Index value to access the CPD row.

OBJECT-TYPE

Deprecated - each Cisco protocol has its own disposition. Control Protocol Disposition for Cisco Group. This includes ISL, PAGP, UDLD, CDP, VTP, DTP, PSVTP+, UplinkFast, VLAN Bridge, L2PT. Note that a specific protocol filter overrides the group setting.

OBJECT-TYPE

Control Protocol Disposition for ISL (Inter Switch Link). MAC Address (01:00:0C:00:00:00).

OBJECT-TYPE

Control Protocol Disposition for PAGP (Port Aggregation Protocol). MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x104).

OBJECT-TYPE

Control Protocol Disposition for UDLD (Unidirectional Link Detection). MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x111).

OBJECT-TYPE

Control Protocol Disposition for CDP (Cisco Discovery Protocol). MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x2000).

OBJECT-TYPE

Control Protocol Disposition for VTP (VLAN Trunking Protocol). MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x2003).

OBJECT-TYPE

Control Protocol Disposition for DTP (Dynamic Trunking). MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x2004).

OBJECT-TYPE

Control Protocol Disposition for Spanning Tree PVSTP+. MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x10B).

OBJECT-TYPE

Control Protocol Disposition for STP UplinkFast. MAC Address (01:00:0C:CD:CD:CD), Ethertype(0x200A).

OBJECT-TYPE

Control Protocol Disposition for VLAN Bridge. MAC Address (01:00:0C:CD:CD:CE), Ethertype(0x10C).

OBJECT-TYPE

Control Protocol Disposition for Layer 2 Protocol Tunnelling(L2PT). MAC Address (01:00:0C:CD:CD:D0).

OBJECT-TYPE

Deprecated - individual dispositions available for each MAC. Bridge Group Control Protocol Disposition Type. This includes BPDU, PAUSE (IEEE 802.3x Flow Control), LACP (Link Aggregation), LACP Marker (Marker), EFM OAM (IEEE 802.3 ah) and IEEE 802.1x Port Authentication, besides reserved MAC addresses from 01:80:C2:00:00:04 thru 01:80:C2:00:00:0F.

OBJECT-TYPE

Control Protocol Disposition for IEEE Spanning Tree(STP), MSTP (Multiple Spanning Tree) and RSTP (Rapid Reconfiguration of Spanning Tree). MAC Address (01:80:C2:00:00:00).

OBJECT-TYPE

Control Protocol Disposition for IEEE 802.3x Flow Control (PAUSE frames).

OBJECT-TYPE

Control Protocol Disposition for 802.3ad Link Aggregation Protocol. MAC Address (01:80:C2:00:00:03), Ethertype (0x8809), Subtype(01).

OBJECT-TYPE

Control Protocol Disposition for IEEE 802.3ad Marker Protocol. MAC Address (01:80:C2:00:00:03), Ethertype (0x8809), Subtype(02).

OBJECT-TYPE

Control Protocol Disposition for IEEE 802.3ah EFM OAM. MAC Address (01:80:C2:00:00:03), Ethertype (0x8809), Subtype(03).

OBJECT-TYPE

Control Protocol Disposition for Sync Status Messages. MAC Address (01:80:C2:00:00:02), Ethertype (0x19A7), Subtype(0A).

OBJECT-TYPE

Control Protocol Disposition for IEEE 802.1x Protocol. MAC Address (01:80:C2:00:00:03), Ethertype (0x888E).

OBJECT-TYPE

Deprecated - individual dispositions available for each MAC. Control Protocol Disposition for Range of MAC Addresses from 01:80:C2:00:00:04 to 01:80:C2:00:00:0F.

OBJECT-TYPE

Control Protocol Disposition for IEEE 802.1d LAN Bridge Managment. MAC Address (01:80:C2:00:00:10).

OBJECT-TYPE

Deprecated - each GARP Group protocol has its own disposition. Group Disposition type which includes GMRP, GVRP and MAC Address from range 01:80:C2:00:00:20 to 01:80:C2:00:00:2F.

OBJECT-TYPE

Control Protocol Disposition for GARP Multicast Registration Protocol. MAC Address (01:80:C2:00:00:20).

OBJECT-TYPE

Control Protocol Disposition for GARP VLAN Registration Protocol. MAC Address (01:80:C2:00:00:21).

OBJECT-TYPE

Group Disposition type which includes GARP Reserved MAC Address from range 01:80:C2:00:00:22 to 01:80:C2:00:00:2F.

OBJECT-TYPE

List of Active Control Protocol Dispositions. Note that if the Port Level Disposition control is set to PEER or DISCARD, the flow level disposition is no longer active. This object provides information on all the active dispositions.

OBJECT-TYPE

Deprecated - each LLDP MAC protocol has its own disposition. LLDP (Link Layer Discovery Protocol) Disposition type. MAC Address 01:80:C2:00:00:0e, 01:80:C2:00:00:03, or 01:80:C2:00:00:00.

OBJECT-TYPE

ELMI (Ethernet Local Management Interface) Disposition type. MAC Address 01:80:C2:00:00:07 and EtherType of 0x88EE.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:00 Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:01 Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:02 Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:03 Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:04 Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:05 Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:06 Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:07 Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:08 Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:09 Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:0A Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:0B Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:0C Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:0D Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:0E Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:0F Disposition type.

OBJECT-TYPE

LLDP (Link Layer Discovery Protocol) Nearest Bridge Disposition type.

OBJECT-TYPE

LLDP (Link Layer Discovery Protocol) Non-TPMR Bridge Disposition type.

OBJECT-TYPE

LLDP (Link Layer Discovery Protocol) Customer Bridge Disposition type.

OBJECT-TYPE

A list of entries corresponding to Ethernet Network Port Control Protocol Disposition V2. This table is supported for the GE206/GE201 devices.

OBJECT-TYPE

A conceptual row in the cmEthernetNetPortCpdV2Table. These entries represent a Control Protocol Disposition filtering criteria on the Ethernet Network Port.

OBJECT-TYPE

Unique Index value to access the CPD row.

OBJECT-TYPE

Deprecated - each Cisco protocol has its own disposition. Control Protocol Disposition for Cisco Group. This includes ISL, PAGP, UDLD, CDP, VTP, DTP, PSVTP+, UplinkFast, VLAN Bridge, L2PT. Note that a specific protocol filter overrides the group setting.

OBJECT-TYPE

Control Protocol Disposition for ISL (Inter Switch Link). MAC Address (01:00:0C:00:00:00).

OBJECT-TYPE

Control Protocol Disposition for PAGP (Port Aggregation Protocol). MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x104).

OBJECT-TYPE

Control Protocol Disposition for UDLD (Unidirectional Link Detection). MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x111).

OBJECT-TYPE

Control Protocol Disposition for CDP (Cisco Discovery Protocol). MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x2000).

OBJECT-TYPE

Control Protocol Disposition for VTP (VLAN Trunking Protocol). MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x2003).

OBJECT-TYPE

Control Protocol Disposition for DTP (Dynamic Trunking). MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x2004).

OBJECT-TYPE

Control Protocol Disposition for Spanning Tree PVSTP+. MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x10B).

OBJECT-TYPE

Control Protocol Disposition for STP UplinkFast. MAC Address (01:00:0C:CD:CD:CD), Ethertype(0x200A).

OBJECT-TYPE

Control Protocol Disposition for VLAN Bridge. MAC Address (01:00:0C:CD:CD:CE), Ethertype(0x10C).

OBJECT-TYPE

Control Protocol Disposition for Layer 2 Protocol Tunnelling(L2PT). MAC Address (01:00:0C:CD:CD:D0).

OBJECT-TYPE

Deprecated - individual dispositions available for each MAC. Bridge Group Control Protocol Disposition Type. This includes BPDU, PAUSE (IEEE 802.3x Flow Control), LACP (Link Aggregation), LACP Marker (Marker), EFM OAM (IEEE 802.3 ah) and IEEE 802.1x Port Authentication, besides reserved MAC addresses from 01:80:C2:00:00:04 thru 01:80:C2:00:00:0F.

OBJECT-TYPE

Control Protocol Disposition for IEEE Spanning Tree(STP), MSTP (Multiple Spanning Tree) and RSTP (Rapid Reconfiguration of Spanning Tree). MAC Address (01:80:C2:00:00:00).

OBJECT-TYPE

Control Protocol Disposition for IEEE 802.3x Flow Control (PAUSE frames).

OBJECT-TYPE

Control Protocol Disposition for 802.3ad Link Aggregation Protocol. MAC Address (01:80:C2:00:00:03), Ethertype (0x8809), Subtype(01).

OBJECT-TYPE

Control Protocol Disposition for IEEE 802.3ad Marker Protocol. MAC Address (01:80:C2:00:00:03), Ethertype (0x8809), Subtype(02).

OBJECT-TYPE

Control Protocol Disposition for IEEE 802.3ah EFM OAM. MAC Address (01:80:C2:00:00:03), Ethertype (0x8809), Subtype(03).

OBJECT-TYPE

Control Protocol Disposition for Sync Status Messages. MAC Address (01:80:C2:00:00:02), Ethertype (0x19A7), Subtype(0A).

OBJECT-TYPE

Control Protocol Disposition for IEEE 802.1x Protocol. MAC Address (01:80:C2:00:00:03), Ethertype (0x888E).

OBJECT-TYPE

Deprecated - individual dispositions available for each MAC. Control Protocol Disposition for Range of MAC Addresses from 01:80:C2:00:00:04 to 01:80:C2:00:00:0F.

OBJECT-TYPE

Control Protocol Disposition for IEEE 802.1d LAN Bridge Managment. MAC Address (01:80:C2:00:00:10).

OBJECT-TYPE

Deprecated - each GARP Group protocol has its own disposition. Group Disposition type which includes GMRP, GVRP and MAC Address from range 01:80:C2:00:00:20 to 01:80:C2:00:00:2F.

OBJECT-TYPE

Control Protocol Disposition for GARP Multicast Registration Protocol. MAC Address (01:80:C2:00:00:20).

OBJECT-TYPE

Control Protocol Disposition for GARP VLAN Registration Protocol. MAC Address (01:80:C2:00:00:21).

OBJECT-TYPE

Group Disposition type which includes GARP Reserved MAC Address from range 01:80:C2:00:00:22 to 01:80:C2:00:00:2F.

OBJECT-TYPE

Deprecated - each LLDP MAC protocol has its own disposition. LLDP (Link Layer Discovery Protocol) Disposition type. MAC Address 01:80:C2:00:00:0e, 01:80:C2:00:00:03, or 01:80:C2:00:00:00.

OBJECT-TYPE

ELMI (Ethernet Local Management Interface) Disposition type. MAC Address 01:80:C2:00:00:07 and EtherType of 0x88EE.

OBJECT-TYPE

Configurable Layer 2 Protocol Tunneling MAC Address. For protocols STP, CDP and VTP, with control protocol disposition as pass-thru-l2pt, this configured MAC address replaces the DA, upon encapsulation. For decapsulation, protocol signature and this configured MAC address are matched and the MAC address is replaced with the protocol's inferred MAC address.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:00 Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:01 Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:02 Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:03 Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:04 Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:05 Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:06 Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:07 Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:08 Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:09 Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:0A Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:0B Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:0C Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:0D Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:0E Disposition type.

OBJECT-TYPE

MAC Address 01:80:C2:00:00:0F Disposition type.

OBJECT-TYPE

LLDP (Link Layer Discovery Protocol) Nearest Bridge Disposition type.

OBJECT-TYPE

LLDP (Link Layer Discovery Protocol) Non-TPMR Bridge Disposition type.

OBJECT-TYPE

LLDP (Link Layer Discovery Protocol) Customer Bridge Disposition type.

OBJECT-TYPE

PTP non forwarding untagged frame Disposition type.

OBJECT-TYPE

PTP tagged frame Disposition type.

OBJECT-TYPE

A list of entries corresponding to BITS Port Facilities for configuration purposes.

OBJECT-TYPE

A conceptual row in the bitsPortTable.

OBJECT-TYPE

An integer index value used to uniquely identify this BITS Port within the card. Value 1 stands for BITS-IN, 2 for BITS-OUT.

OBJECT-TYPE

An integer index value used to uniquely identify this BITS Port within the card. Note that each BITs Port is uniquely identified by the indices neIndex, shelfIndex, slotIndex, bitsPortIndex.

OBJECT-TYPE

This object has the same value as ifIndex for Bits Port. An integer index value used to uniquely identify this Bits Port.

OBJECT-TYPE

Entity Index from ENTITY-MIB for this port.

OBJECT-TYPE

This object represents the Administrative State of the BITS Port.

OBJECT-TYPE

This object represents the Operational State of the BITS Port.

OBJECT-TYPE

This object represents the Secondary State of the BITS Port.

OBJECT-TYPE

This object represents the BITS Port Type.

OBJECT-TYPE

This object represents the BITS Port Line Type. Determines whether the T1/E1 BITS port operates in T1, E1, or 2048kHz mode.

OBJECT-TYPE

This object represents the BITS Port Line Code. When the port is configured for a Line Type of T1, the valid values are t1-b8zs and t1-ami and the default value is t1-b8zs. When the port is configured for a Line Type of E1, the valid values are e1-hdb3 and e1-ami and the default value is e1-hdb3. When the port is configured for a Line Type of 2048kHz, the value is none.

OBJECT-TYPE

This object represents the BITS Port Frame Format. When the port is configured for a Line Type of T1, the valid values are t1-sf and t1-esf and the default value is t1-esf. When the port is configured for a Line Type of E1, the valid values are e1-unframed, e1-crc4, and e1-dualFrame and the default value is e1-crc4. When the port is configured for a Line Type of 2048kHz, the value is none. R4.1CC and R4.3CC do not support e1-unframed.

OBJECT-TYPE

This object represents the BITS Port Sa Bit Designation. Determines which E1 Sa Bit is used to transmit/receive the SSM. For T1 and 2048khz Line Types, the only allowed value is None. For E1 Line Type, the default value is bit4 and it can only have a value of None if QL Mode is disabled, otherwise, None is an invalid value.

OBJECT-TYPE

This object allows to specify whether the BITS Port can be enabled/disabled for QL Mode. When enabled, on receive side -port shall PEER the SSM (Sync Status Messages) slow protocol PDUs and take appropriate action When enabled, on transmit side -port shall periodically (once a second) transmit QL TLV information PDUs When disabled, on receive side, -port shall terminate and discard any SSM slow protocol PDUs When disabled, on transmit side -port shall not transmit any SSM slow protocol PDUs.

OBJECT-TYPE

This object allows to specify the expected QL when the BITS Port is enabled for QL Mode. This object allows the user to set a minimum expected received Quality Level on the port. The default value shall be None.

OBJECT-TYPE

This object allows to specify the assumed QL on the BITS Port. The Assumed QL is only meaningful if the Network Clock Type (see fsp150cm-sync.mib) is option1 and the port's QL Mode is disabled and the port is being used as an input reference source. Under these conditions, the specified QL value is assumed to be the Quality Level of the non-failed reference.

OBJECT-TYPE

This object provides the Received QL value for the BITS port. If the BITS port's QL Mode is disabled, then the received QL value is not applicable.

OBJECT-TYPE

This object provides the Transmitted QL value for the BITS port. If the BITS port's QL Mode is disabled, then the received QL value is not applicable.

OBJECT-TYPE

This object allows to set the Squelch QL for the BITS-OUT port. The Squelch QL is only meaningful if the QL Mode is Enabled. The Squelch QL is used to determine whether or not to squelch the output of the BITS-OUT port. If the system's QL is lower than the Squelch QL, the output is squelched. If the BITS port's QL Mode is disabled, then the received QL value is not applicable.

OBJECT-TYPE

This object allows to manage the line build out on the BITS-OUT port when the Line Type is T1.

OBJECT-TYPE

This object provides the impedance mode for the BITS-OUT port.

OBJECT-TYPE

This object allows to include or not the CRC to the signal of the BITS-OUT port.

OBJECT-TYPE

This object allows to manage the Idle Code for the BITS-OUT port.

OBJECT-TYPE

This object allows to set the AIS signal for the BITS-OUT port.

OBJECT-TYPE

This object allows to manage the five Sa Bit values, from bit4 to bit8, for the BITS-OUT port. The object value is a BIT string that concatenate the Sa Bit values. The Sa Bit values are applied to each of the five Sa Bits of the output signal except to the one that carries SSM information when QL Mode is enabled.

OBJECT-TYPE

This object indicates the Squelch Control for the port. The Squelch Control determines the type of squelch control used to squelch an output of the port.

OBJECT-TYPE

This object represents the Port Signal Shape. Indicates whether the signal has a sine or a square shape.

OBJECT-TYPE

Indicates the signal frequency of the port. Possible value are 100 kHz, 1 MHz, 1544 kHz, 2048 kHz, 5 MHz, 25 Mhz or 50 MHz. It can be set only to a port that is dedicated to yield a variety of frequencies.

OBJECT-TYPE

A list of entries corresponding to IEEE Ethernet Port Facilities for configuration purposes.

OBJECT-TYPE

A conceptual row in the IEEE Ethernet Port Table.

OBJECT-TYPE

An integer index value used to uniquely identify the IEEE Ethernet Port.

OBJECT-TYPE

This object has the same value as ifIndex for the IEEE Ethernet Port.

OBJECT-TYPE

Entity Index from ENTITY-MIB for this port.

OBJECT-TYPE

This object represents the Administrative State of the Port.

OBJECT-TYPE

This object represents the Operational State of the Port.

OBJECT-TYPE

This object represents the Secondary State of the Port.

OBJECT-TYPE

This object provides the MTU on the Port.

OBJECT-TYPE

This object represents the type of Media.

OBJECT-TYPE

This object allows to configure the speed of the Port.

OBJECT-TYPE

This object provides the negotiated speed of the Port.

OBJECT-TYPE

This object allows management of MDIX property on Port.

OBJECT-TYPE

A list of entries corresponding to GPS 10MHz Facilities for configuration purposes.

OBJECT-TYPE

A conceptual row in the GPS 10MHz Port Table.

OBJECT-TYPE

An integer index value used to uniquely identify the IEEE Ethernet Port.

OBJECT-TYPE

This object has the same value as ifIndex for the IEEE Ethernet Port.

OBJECT-TYPE

Entity Index from ENTITY-MIB for this port.

OBJECT-TYPE

This object represents the Administrative State of the Port.

OBJECT-TYPE

This object represents the Operational State of the Port.

OBJECT-TYPE

This object represents the Secondary State of the Port.

OBJECT-TYPE

This object allows specification of the signal type (i.e. input or output).

OBJECT-TYPE

This object allows to set the Squelch Control for the 10MHz port. The Squelch Control is used to determine the type of squelch control used to squelch the output of the TOD port. Only option supported is squelch-ql.

OBJECT-TYPE

This object allows to set the Squelch QL for the 10MHz port. This value is used when f310MHzClockPortSquelchControl is squelch-ql. The Squelch QL is used to determine whether or not to squelch the output of the TOD port. If the system's QL is lower than the Squelch QL, the output is squelched.

OBJECT-TYPE

This object allows to set the Frequency Source for the Port.

OBJECT-TYPE

This object specify GPS port clock class.

OBJECT-TYPE

This object specify GPS port clock accuracy.

OBJECT-TYPE

This object specify GPS port time source.

OBJECT-TYPE

This object allows to specify the assumed QL on the GPS Port. The Assumed QL is only meaningful if the Network Clock Type (see fsp150cm-sync.mib) is option1 and the port's QL Mode is disabled and the port is being used as an input reference source. Under these conditions, the specified QL value is assumed to be the Quality Level of the non-failed reference.

OBJECT-TYPE

This object allows SNMP management entities to provide an alias to the gps 10MHz Port entity.

OBJECT-TYPE

This object allows specification of the input signal type (i.e. 10mhz or 2048khz).

OBJECT-TYPE

A list of entries corresponding to Ethernet Network Port Cable Length Benchmark.

OBJECT-TYPE

A conceptual row in the cmEthernetNetPortClbTable. These entries represent Cable Length Benchmarks on the Ethernet Network Port.

OBJECT-TYPE

An integer index value used to uniquely identify this Cable Length Benchmark Entry specification.

OBJECT-TYPE

This enables specification of Cable Length Benchmark entry.

OBJECT-TYPE

Cable length of Cable Points Entry. The cable length is of the form XXX[.YY] where XX can be any integer value and YY allows precision of 2 decimals after the floating point. Note that .YY is optional.

OBJECT-TYPE

A textual string containing description of cable span.

OBJECT-TYPE

A list of entries corresponding to Ethernet Network Port Priority Mappings in multi Class of Service (COS) mode.

OBJECT-TYPE

A conceptual row in the cmNetPortPrioMapTable.

OBJECT-TYPE

The integer index value corresponding to a priority value.

OBJECT-TYPE

The integer index value corresponding to a priority value.

OBJECT-TYPE

This allows specification of the COS Priority, i.e. this helps in determining the appropriate COS Policer for the Flow.

OBJECT-TYPE

This allows specification of the VLAN priority that will replace the outgoing (N2A direction) outer-tag's priority. Note that, each flow participates or not in outer-tag priority mapping, using the object 'cmFlowN2AOuterTagPrioEnabled'.

OBJECT-TYPE

Ethernet Access Port PCP drop eligibility encoding table. This is applied to a frame that is egressing at the Access port.

OBJECT-TYPE

A conceptual row in the ethernetPBPcpDEEncPortTable.

OBJECT-TYPE

An integer index value used to uniquely identify a row in the PCP drop eligible encoding table.

OBJECT-TYPE

This object is the input priority that is translated to a drop eligibility priority or a drop ineligibility priority.

OBJECT-TYPE

This object is the PCP value that has a priority value with implicit drop ineligibility encoded into it.

OBJECT-TYPE

This object is the PCP value that has a priority value with implicit drop eligibility encoded into it.

OBJECT-TYPE

Ethernet Access Port PCP drop eligibility decoding table. This is applied to a frame that is ingressing at a port.

OBJECT-TYPE

A conceptual row in the ethernetPBPcpDEDecPortTable.

OBJECT-TYPE

An integer index value used to uniquely identify a row in the PCP drop eligible decoding table.

OBJECT-TYPE

This object is the input priority that is decoded to get priority and the drop eligibility of a frame.

OBJECT-TYPE

This object is the priority value decoded from a incoming PCP value.

OBJECT-TYPE

This object is the drop eligibility decoded from a incoming PCP value.

OBJECT-TYPE

Ethernet Access Port PCP drop eligibility priority pair table. The priority pair is encoded to same drop eligibility and drop ineligibility priority. Depending on the PCP DE Enc/Dec mode there can be upto 3 pairs in the table. There will one pair for 7P1D, two pairs for 6P2D and three pairs for 5P3D.

OBJECT-TYPE

A conceptual row in the cmAccPortPcpDEPairEntry.

OBJECT-TYPE

An integer index value used to uniquely identify a row in the PCP drop eligible priority pair table.

OBJECT-TYPE

This object is the drop ineligible priority.

OBJECT-TYPE

This object is the drop eligible priority.

OBJECT-TYPE

Ethernet Network Port PCP drop eligibility encoding table. This is applied to a frame that is egressing at the Network port.

OBJECT-TYPE

A conceptual row in the ethernetPBPcpDEEncPortTable.

OBJECT-TYPE

An integer index value used to uniquely identify a row in the PCP drop eligible encoding table.

OBJECT-TYPE

This object is the input priority that is translated to a drop eligibility priority or a drop ineligibility priority.

OBJECT-TYPE

This object is the PCP value that has a priority value with implicit drop ineligibility encoded into it.

OBJECT-TYPE

This object is the PCP value that has a priority value with implicit drop eligibility encoded into it.

OBJECT-TYPE

Ethernet Network Port PCP drop eligibility decoding table. This is applied to a frame that is ingressing at a port.

OBJECT-TYPE

A conceptual row in the ethernetPBPcpDEDecPortTable.

OBJECT-TYPE

An integer index value used to uniquely identify a row in the PCP drop eligible decoding table.

OBJECT-TYPE

This object is the input priority that is decoded to get priority and the drop eligibility of a frame.

OBJECT-TYPE

This object is the priority value decoded from a incoming PCP value.

OBJECT-TYPE

This object is the drop eligibility decoded from a incoming PCP value.

OBJECT-TYPE

Ethernet Network Port PCP drop eligibility priority pair table. The priority pair is encoded to same drop eligibility and drop ineligibility priority. Depending on the PCP DE Enc/Dec mode there can be upto 3 pairs in the table. There will one pair for 7P1D, two pairs for 6P2D and three pairs for 5P3D.

OBJECT-TYPE

A conceptual row in the cmNetPortPcpDEPairEntry.

OBJECT-TYPE

An integer index value used to uniquely identify a row in the PCP drop eligible priority pair table.

OBJECT-TYPE

This object is the drop ineligible priority.

OBJECT-TYPE

This object is the drop eligible priority.

OBJECT-TYPE

A list of entries corresponding to Ethernet Facilities for configuration purposes.

OBJECT-TYPE

A conceptual row in the cmEthernetTrafficPortTable.

OBJECT-TYPE

An integer index value used to uniquely identify this Ethernet Port within a card. Note that each Ethernet Port is uniquely identified by the indices neIndex, shelfIndex, slotIndex, cmEthernetTrafficPortIndex.

OBJECT-TYPE

This object has the same value as ifIndex for Ethernet Port. An integer index value used to uniquely identify this Ethernet Port.

OBJECT-TYPE

Entity Index from ENTITY-MIB for this port.

OBJECT-TYPE

This object represents the Administrative State of the Ethernet Port.

OBJECT-TYPE

This object represents the Operational State of the Ethernet Port.

OBJECT-TYPE

This object represents the Secondary State of the Ethernet Port.

OBJECT-TYPE

This object provides the MTU on the Ethernet Port. The object is made read-write for FSP150CC devices.

OBJECT-TYPE

This object represents the type of Ethernet Media on the Ethernet Port. The media type includes, copper (1) fiber (2) coppersfp (3) CM Aggregation Product doesn't support copper.

OBJECT-TYPE

This object allows to configure the speed of the Ethernet Port.

OBJECT-TYPE

This object provides the negotiated speed of the Ethernet Port.

OBJECT-TYPE

This object allows management of MDIX property on Ethernet Port.

OBJECT-TYPE

This object provides the current MDIX status of the Ethernet port.

OBJECT-TYPE

This object provides the vendor name of the SFP. This is applicable when cmEthernetTrafficPortMediaType is fiber or coppersfp.

OBJECT-TYPE

This object provides the part number of the SFP. This is applicable when cmEthernetTrafficPortMediaType is fiber or coppersfp.

OBJECT-TYPE

This object provides the serial number of the SFP. This is shown only when cmEthernetTrafficPortMediaType is fiber.

OBJECT-TYPE

This object provides the date of manufacture of the SFP. This is applicable when cmEthernetTrafficPortMediaType is fiber or coppersfp.

OBJECT-TYPE

This object provides the SFP connector value. This is applicable when cmEthernetTrafficPortMediaType is fiber or coppersfp.

OBJECT-TYPE

This object provides the SFP Link Length. This is applicable only when cmEthernetTrafficPortMediaType is fiber or coppersfp.

OBJECT-TYPE

This object provides the SFP Laser Wave Length in nano meters. This is applicable only when cmEthernetTrafficPortMediaType is fiber.

OBJECT-TYPE

This object provides the SFP Media Type. This is applicable only when cmEthernetTrafficPortMediaType is fiber or coppersfp.

OBJECT-TYPE

This object allows to initiate loopbacks on on the Ethernet Port.

OBJECT-TYPE

This object provides status of the current loopback on the Ethernet Port.

OBJECT-TYPE

This object allows to specify time for timed-loopbacks on on the Ethernet Port.

OBJECT-TYPE

This object allows to specify whether or not the loopbacked frame will have the Source Address and Destination Address swapped.

OBJECT-TYPE

This object allows specification of the outer VLANs to be looped back when port is in vlan(terminal/facility) loopback configuration. Only 3 VLANs can be specified for vlan loopback. The various bit positions are: 1 Outer VLAN 1 Loopback Enabled 2 Outer VLAN 2 Loopback Enabled 4 Outer VLAN 3 Loopback Enabled

OBJECT-TYPE

This object allows specification of the outer VLAN 1 to be looped back when port is in vlan(terminal/facility) loopback configuration. This is valid only if the corresponding bit in cmEthernetTrafficPortOuterVlanLoopbackMask is set. The value to be specified should be in the form X-Y where X is the VLAN Id and Y is the VLAN Priority. If Y is specified as a *, all Priorities (0 to 7) are looped back.

OBJECT-TYPE

This object allows specification of the outer VLAN 2 to be looped back when port is in vlan(terminal/facility) loopback configuration. This is valid only if the corresponding bit in cmEthernetTrafficPortOuterVlanLoopbackMask is set. The value to be specified should be in the form X-Y where X is the VLAN Id and Y is the VLAN Priority. If Y is specified as a *, all Priorities (0 to 7) are looped back.

OBJECT-TYPE

This object allows specification of the outer VLAN 3 to be looped back when port is in vlan(terminal/facility) loopback configuration. This is valid only if the corresponding bit in cmEthernetTrafficPortOuterVlanLoopbackMask is set. The value to be specified should be in the form X-Y where X is the VLAN Id and Y is the VLAN Priority. If Y is specified as a *, all Priorities (0 to 7) are looped back.

OBJECT-TYPE

This object allows enabling/disabling link loss forwarding on the Ethernet Port.

OBJECT-TYPE

This object allows definition of the link loss forwarding signalling type. This is applicable only if cmEthernetTrafficPortLinkLossFwdEnabled is enabled.

OBJECT-TYPE

This object allows definition of the link loss forwarding trigger types. This is applicable only if cmEthernetTrafficPortLinkLossFwdEnabled is enabled.

OBJECT-TYPE

This object allows specification of the delay between detection of link loss and signalling of link loss forwarding. Time specified is in seconds.

OBJECT-TYPE

This object provides the link loss forwarding status indicating if link loss forwarding is currently being signaled via the port.

OBJECT-TYPE

This object provides the indication of a link partners ability to support link loss forwarding via EFM, i.e. from received organization specific OAMPDUs.

OBJECT-TYPE

This object allows configuration of the Local Link Id on Ethernet port.

OBJECT-TYPE

This object allows enabling/disabling Remote Link Ids on Ethernet port. The Ethernet port is able to distinguish the remote side client ports from the Remote Link Down PDUs coming from remote end. Input format allows multiple Remote Link Ids seperated by comma (e.g. 1,2,3,10,20...). Number range is product-specific (for EGX8.1, max value is 554). Empty string clears the configuration.

OBJECT-TYPE

This object allows to specify the Ethernet Port's behavior when link loss forwarding trigger events occur on the Port. This provides ability to configure per Ethernet port LLF behavior.

OBJECT-TYPE

This object provides the received Remote Link IDs in EFM RLD messages on the Ethernet Port.

OBJECT-TYPE

OAM Id. This is unique EFM OAM sublayer port id.

OBJECT-TYPE

Ethernet Port's OAM discovery state.

OBJECT-TYPE

This object allows specification of whether the Ethernet Port supports sending variable response OAMPDUs.

OBJECT-TYPE

This object allows specification of whether the Ethernet Port supports interpreting Link Events.

OBJECT-TYPE

This object allows specification of whether the Ethernet Port is capable of OAM remote loopback mode.

OBJECT-TYPE

This object allows specification of whether the Ethernet Port is capable of sending OAMPDUs when the receive path is non-operational.

OBJECT-TYPE

This object represents the largest OAMPDU, in octets, supported by the Ethernet Port. This value is compared to the remote Maximum PDU Size and the smaller of the two is used.

OBJECT-TYPE

This object allows to configure the OAM sublayer entity in either Active or Passive mode.

OBJECT-TYPE

This object allows retrieval of the Remote Mac Address.

OBJECT-TYPE

This object allows retrieval of whether the remote OAM entity supports sending variable response OAMPDUs.

OBJECT-TYPE

This object allows retrieval of whether the remote OAM entity supports interpreting Link Events.

OBJECT-TYPE

This object allows retrieval of whether the remote OAM entity supports OAM remote loopback mode.

OBJECT-TYPE

This object allows retrieval of whether the remote OAM entity is capable of sending OAMPDUs when the receive path is non-operational.

OBJECT-TYPE

This object allows retrieval of the remote OAM entity maximum OAMPDU size.

OBJECT-TYPE

This object allows to retrieve whether the remote OAM sublayer entity is either in Active or Passive mode.

OBJECT-TYPE

This object allows to manage the EFM OAM on Ethernet Traffic Port.

OBJECT-TYPE

This object provides the EFM OAM Admin State.

OBJECT-TYPE

This object allows specification of whether the Ethernet Port is port based or vlan based.

OBJECT-TYPE

This object defines the RxPause enable or disable of the port.

OBJECT-TYPE

This object allows enabling/disabling transmit pause frames on Ethernet port.

OBJECT-TYPE

This object allows specification of the Acceptable Frame Policy on Ethernet port. Users can specify whether the port supports only tagged frames, only untagged frames or both tagged and untagged frames.

OBJECT-TYPE

This object allows to manage the Ethernet Port Shaping. When enabled, values in cmEthernetTrafficPortShapedSpeedLo and cmEthernetTrafficPortShapedSpeedHi are applicable.

OBJECT-TYPE

This object allows to specify the lower 32 bits of the Ethernet Port Shaped speed. This value is applicable when cmEthernetTrafficPortShapingEnabled is enabled.

OBJECT-TYPE

This object allows to specify the higher 32 bits of the Port Shaped speed. This value is applicable when cmEthernetTrafficPortShapingEnabled is enabled.

OBJECT-TYPE

This object allows to specify the Q-in-Q Ether Type on the Port.

OBJECT-TYPE

This object defines if c-tag/s-tag frame is allowed to pass through, available only when AFP is set to Tagged.

OBJECT-TYPE

This object allows to enable or disable the VLAN trunking on Ethernet port. Disabling VLAN trunking removes all VLAN tags before transmitting traffic out of the port. This object is only applicable for connection-oriented, evpl service type.

OBJECT-TYPE

This object allows to specify whether cmEthernetTrafficPortPortVlanId value will be PUSHed on untagged frames or not in the ingress direction. This object is only applicable for connection-oriented, evpl service type.

OBJECT-TYPE

This object allows to specify whether cmEthernetTrafficPortPortVlanId value will be POPed in the egress direction. This object is only applicable for connection-oriented, evpl service type.

OBJECT-TYPE

This object defines the egress PopPriorityVid enable or disable of the port. If it is enabled, the outgoing packets with VID=Priority VLAN ID will be swapped back to VID=0. This attribute has been deprecated and is supported only on EG-X. Please use cmEthernetTrafficPortEgressSwapPriorityVIDEnabled

OBJECT-TYPE

This object allows to specify the Ethernet Port VLAN Id to PUSH on untagged frames in the to Network direction. This object is only applicable for connection-oriented, evpl service type, when cmEthernetTrafficPortIngressPushPVIDEnabled is set to true.

OBJECT-TYPE

This object allows to specify the Ethernet Port VLAN Priority for the PUSHed VLAN tag (specified by cmEthernetTrafficPortPortVlanId) on untagged frames in the ingress direction. This object is only applicable for connection-oriented, evpl service type, when cmEthernetTrafficPortIngressPushPVIDEnabled is set to true.

OBJECT-TYPE

This object allows to specify the Ethernet Priority VLAN Id to replace the null-tagged or priority tagged frames in the to ingress direction. This object is only applicable for connection-oriented, evpl service type. This attribute has been deprecated and is supported only on EG-X. Please use cmEthernetTrafficPortSwapPriorityVID

OBJECT-TYPE

This object allows to specify the Ethernet Port Priority Mapping Mode used for classification of frames. This object is only applicable for connection-oriented, evpl service type.

OBJECT-TYPE

This object is used to specify whether the EthernetTrafficPort uses the inner-tag or the outer-tag in determining the COS (Class of Service). This attribute has been deprecated and is not supported. Now, the Priority Map Mode indicates whether it is inner or outer. Use priomap-8021p(4) for outer and priomap-8021p-inner(5) for inner.

OBJECT-TYPE

This object allows to specify whether the Ethernet Port can be enabled/disabled for Synchronous Ethernet. This object is only applicable for Synchronous Ethernet capable ports. When enabled, on receive side -port can extract the frequency of its input signal and pass the recovered clock to the system clock -port processes the ESMC(Ethernet Synchronization Messaging Channel) and extracts the QL (when also QL enabled) -port is eligible to be selected as a system clock reference When enabled, on transmit side -port's transmit clock is locked to the system clock -port generates an ESMC to generate a QL (when also QL enabled) When disabled, on receive side, -port does not pass the recovered clock to the system clock -port does not process the ESMC (if present) -port is not eligible to be selected as a system clock reference When disabled, on transmit side -port's output frequency may be synchronized to the system clock -port does not generate an ESMC.

OBJECT-TYPE

This object allows to specify whether the Ethernet Port can be enabled/disabled for QL Mode. This object is only applicable for Synchronous Ethernet capable ports, when cmEthernetTrafficPortQLModeEnabled is set to true. When enabled, on receive side -port shall PEER the SSM (Sync Status Messages) slow protocol PDUs and take appropriate action When enabled, on transmit side -port shall periodically (once a second) transmit QL TLV information PDUs When disabled, on receive side, -port shall terminate and discard any SSM slow protocol PDUs When disabled, on transmit side -port shall not transmit any SSM slow protocol PDUs.

OBJECT-TYPE

This object allows to specify the expected QL when the Ethernet Port is enabled for QL Mode. This object is only applicable for Synchronous Ethernet capable ports, when cmEthernetTrafficPortQLModeEnabled is set to true. This object allows the user to set a minimum expected received Quality Level on the port. The valid values depend upon the SYNC entity Network Clock Type. A value of None represents that a minimum Quality Level is not expected. The default value shall be None.

OBJECT-TYPE

This object allows to specify the assumed QL on the Ethernet Port. This object is only applicable for Synchronous Ethernet capable ports. The Assumed QL is only meaningful if the Network Clock Type (see fsp150cm-sync.mib) is option1 and the port TransmitQL Mode is disabled and the port is being used as an input reference source. Under these conditions, the specified QL value is assumed to be the Quality Level of the non-failed reference.

OBJECT-TYPE

This object provides the Received QL value for the Ethernet port. If the Ethernet port TransmitQL Mode is disabled, then the received QL value is not applicable.This object is only applicable for Synchronous Ethernet capable ports.

OBJECT-TYPE

This object provides the Transmitted QL value for the Ethernet port. If the Ethernet port TransmitQL Mode is disabled, then the received QL value is not applicable. This object is only applicable for Synchronous Ethernet capable ports.