MIBs Depot

F3-PWE3-MIB

Registered at
1.3.6.1.4.1.2544.1.12.19
Last updated
2012-04-03 00:00
Organization
ADVA Optical Networking
Revisions
2012-04-03 00:00
Namespace
adva
Source file
F3-PWE3-MIB
Digest
sha256:f38d26957bdc1dc11f5acfdcf67b8c0e336dc5a5940be6e85d2795cdaae1268c

Description

This module provides the F3 Pseudo Wire definitions used by the F3 (FSP150CM/CC) product lines. Copyright (C) ADVA Optical Networking.

Contact

Raghav Trivedi ADVA Optical Networking, Inc. Tel: +1 972 759-1239 E-mail: rtrivedi@advaoptical.com Postal: 2301 N. Greenville Ave. #300 Richardson, TX USA 75082

Imports

FromSymbols
ADVA-MIBfsp150cm
CM-COMMON-MIBAdminState, CmPmBinAction, CmPmIntervalType, IpPriorityMapMode, IpVersion, OperationalState, PerfCounter64, SecondaryState, VlanId, VlanPriority
CM-ENTITY-MIBneIndex, shelfIndex, slotIndex
CM-FACILITY-MIBcmEthernetAccPortIndex, cmEthernetNetPortIndex
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP
SNMPv2-SMICounter64, Integer32, IpAddress, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, Unsigned32, iso
SNMPv2-TCDateAndTime, DisplayString, MacAddress, RowStatus, StorageType, TEXTUAL-CONVENTION, TruthValue, VariablePointer

Imported by

Nothing in this corpus imports this module.

Load order

Every file a consumer needs in order to load this module, dependencies first.

ADVA-MIB
CM-COMMON-MIB
CM-ENTITY-MIB
CM-FACILITY-MIB
CM-REDUNDANCY-MIB
CM-SYSTEM-MIB
ENTITY-MIB
F3-LAG-MIB
F3-PWE3-MIB
F3-SYNC-MIB
IANA-ADDRESS-FAMILY-NUMBERS-MIB
IANA-ENTITY-MIB
IANAifType-MIB
IF-MIB
IPV6-TC
LLDP-V2-MIB
LLDP-V2-TC-MIB
RFC1158-MIB
RFC1271-MIB
RMON-MIB
RMON2-MIB
SNMP-FRAMEWORK-MIB
SNMP-TARGET-MIB
SNMPv2-CONF
SNMPv2-MIB
SNMPv2-SMI
SNMPv2-TC
TOKEN-RING-RMON-MIB
UUID-TC-MIB

Textual conventions

NameOIDSyntaxAccessStatus
MplsLabel
TEXTUAL-CONVENTION
Definition of MPLS Label. The bits in network order (left-to-right) are, Label(20-bits):QOS(3-bits):Bottom-of-Stack(1-bit):TTL(8-bits) These constitute the 32-bit unsigned integer.
current
PWE3SatopDiscoveryType
TEXTUAL-CONVENTION
Enumerations for PWE3 SATop Discovery Type.
current
PWE3SatopEncapsulationType
TEXTUAL-CONVENTION
Enumerations for PWE3 SATop Encapsulation Type.
current
PWE3SatopRTPTSUpdateFreqType
TEXTUAL-CONVENTION
Enumerations for PWE3 SATop RTP Update Frequency.
current
PWE3SatopTransportMode
TEXTUAL-CONVENTION
Enumerations for PWE3 SATop Transport Mode.
current

Objects

NameOIDSyntaxAccessStatus
f3Pwe3ConfigObjects
OBJECT-IDENTITY
1.3.6.1.4.1.2544.1.12.19.1
f3Pwe3IdlePatternProfileTable
OBJECT-TYPE
A list of entries corresponding to the PWE3 Idle Pattern Profile entities.
1.3.6.1.4.1.2544.1.12.19.1.1not-accessiblecurrent
f3Pwe3IdlePatternProfileEntry
OBJECT-TYPE
An entry containing information applicable to a particular PWE3 Idle Pattern Profile Entity. These profiles are used by PWE3 SAToP entities.
1.3.6.1.4.1.2544.1.12.19.1.1.1not-accessiblecurrent
f3Pwe3IdlePatternProfileIndex
OBJECT-TYPE
Unique index value associated with the PWE3 Idle Pattern Profile.
1.3.6.1.4.1.2544.1.12.19.1.1.1.1Integer32not-accessiblecurrent
f3Pwe3IdlePatternProfileByte
OBJECT-TYPE
This object allows SNMP management entities to specify the Idle Pattern Profile information.
1.3.6.1.4.1.2544.1.12.19.1.1.1.2Unsigned32read-writecurrent
f3Pwe3ResyncProfileTable
OBJECT-TYPE
A list of entries corresponding to the PWE3 Resync Profile entities.
1.3.6.1.4.1.2544.1.12.19.1.2not-accessiblecurrent
f3Pwe3ResyncProfileEntry
OBJECT-TYPE
An entry containing information applicable to a particular PWE3 Resync Profile Entity. These profiles are used by PWE3 SAToP entities.
1.3.6.1.4.1.2544.1.12.19.1.2.1not-accessiblecurrent
f3Pwe3ResyncProfileIndex
OBJECT-TYPE
Unique index value associated with the PWE3 Resync Profile.
1.3.6.1.4.1.2544.1.12.19.1.2.1.1Integer32not-accessiblecurrent
f3Pwe3ResyncProfileIncreaseFactor
OBJECT-TYPE
This object allows SNMP management entities to specify the PWE3 Resync Profile Increase Factor. This is used to define the fill rate of the leaky bucket algorithm associated with the Resync mechanism.
1.3.6.1.4.1.2544.1.12.19.1.2.1.2Unsigned32read-writecurrent
f3Pwe3ResyncProfileDecreaseFactor
OBJECT-TYPE
This object allows SNMP management entities to specify the PWE3 Resync Profile Decrease Factor. This is used to define the leak rate for the leaky bucket algorithm associated with the Resync mechanism.
1.3.6.1.4.1.2544.1.12.19.1.2.1.3Unsigned32read-writecurrent
f3Pwe3ResyncProfileResyncThreshold
OBJECT-TYPE
This object allows SNMP management entities to specify the PWE3 Resync Profile Resync Threshold. This is the threshold value at which point the pseudo-wire connection is deemed out of synchronization state.
1.3.6.1.4.1.2544.1.12.19.1.2.1.4Unsigned32read-writecurrent
f3Pwe3LoopbackProfileTable
OBJECT-TYPE
A list of entries corresponding to the PWE3 Loopback Profile entities.
1.3.6.1.4.1.2544.1.12.19.1.3not-accessiblecurrent
f3Pwe3LoopbackProfileEntry
OBJECT-TYPE
An entry containing information applicable to a particular PWE3 Loopback Profile Entity. These profiles are used by PWE3 T1/E1 interfaces.
1.3.6.1.4.1.2544.1.12.19.1.3.1not-accessiblecurrent
f3Pwe3LoopbackProfileIndex
OBJECT-TYPE
Unique index value associated with the PWE3 Loopback Profile.
1.3.6.1.4.1.2544.1.12.19.1.3.1.1Integer32not-accessiblecurrent
f3Pwe3LoopbackProfileLength
OBJECT-TYPE
This object allows SNMP management entities to specify the PWE3 Loopback Length.
1.3.6.1.4.1.2544.1.12.19.1.3.1.2Unsigned32read-writecurrent
f3Pwe3LoopbackProfilePattern
OBJECT-TYPE
This object allows SNMP management entities to specify the PWE3 Loopback Pattern.
1.3.6.1.4.1.2544.1.12.19.1.3.1.3Unsigned32read-writecurrent
f3Pwe3LoopbackProfileRepeatTime
OBJECT-TYPE
This object allows SNMP management entities to specify the PWE3 Loopback Profile Repeat Time (Duration).
1.3.6.1.4.1.2544.1.12.19.1.3.1.4Unsigned32read-writecurrent
f3Pwe3LoopbackProfileClearLength
OBJECT-TYPE
This object allows SNMP management entities to specify the Loopback PWE3 Clear Length.
1.3.6.1.4.1.2544.1.12.19.1.3.1.5Unsigned32read-writecurrent
f3Pwe3LoopbackProfileClearPattern
OBJECT-TYPE
This object allows SNMP management entities to specify the PWE3 Loopback Clear Pattern.
1.3.6.1.4.1.2544.1.12.19.1.3.1.6Unsigned32read-writecurrent
f3Pwe3LossProfileTable
OBJECT-TYPE
A list of entries corresponding to the PWE3 Loss Profile entities.
1.3.6.1.4.1.2544.1.12.19.1.4not-accessiblecurrent
f3Pwe3LossProfileEntry
OBJECT-TYPE
An entry containing information applicable to a particular PWE3 Loss Profile Entity. These profiles are used by PWE3 SAToP entities.
1.3.6.1.4.1.2544.1.12.19.1.4.1not-accessiblecurrent
f3Pwe3LossProfileIndex
OBJECT-TYPE
Unique index value associated with the PWE3 Loss Profile.
1.3.6.1.4.1.2544.1.12.19.1.4.1.1Integer32not-accessiblecurrent
f3Pwe3LossProfileLossStateEnterTime
OBJECT-TYPE
This object allows SNMP management entities to specify the holdoff time that will be applied prior to the SAToP instance entering a Loss State.
1.3.6.1.4.1.2544.1.12.19.1.4.1.2Unsigned32read-writecurrent
f3Pwe3LossProfileLossStateExitTime
OBJECT-TYPE
This object allows SNMP management entities to specify the holdon time that will be applied when the conditon causing the loss state clears.
1.3.6.1.4.1.2544.1.12.19.1.4.1.3Unsigned32read-writecurrent
f3Pwe3AisStabilizationProfileTable
OBJECT-TYPE
A list of entries corresponding to the PWE3 AisStabilization Profile entities.
1.3.6.1.4.1.2544.1.12.19.1.5not-accessiblecurrent
f3Pwe3AisStabilizationProfileEntry
OBJECT-TYPE
An entry containing information applicable to a particular PWE3 AisStabilization Profile Entity. These profiles are used by PWE3 SAToP entities.
1.3.6.1.4.1.2544.1.12.19.1.5.1not-accessiblecurrent
f3Pwe3AisStabilizationProfileIndex
OBJECT-TYPE
Unique index value associated with the PWE3 AIS Stabilization Profile.
1.3.6.1.4.1.2544.1.12.19.1.5.1.1Integer32not-accessiblecurrent
f3Pwe3AisStabilizationProfileEnterTime
OBJECT-TYPE
This object allows SNMP management entities to specify the time (in hundreds of milliseconds) that will be applied on a LOS event, before the SAToP instance transmits all 1s pattern downstream (AIS). Range 0 to 3 seconds in 100 millisecond increments.
1.3.6.1.4.1.2544.1.12.19.1.5.1.2Unsigned32read-writecurrent
f3Pwe3AisStabilizationProfileExitTime
OBJECT-TYPE
This object allows SNMP management entities to specify the holdon time that will be applied when leaving the AIS Stabilization period. Range 0 to 3 seconds in 100 milliseconds increments (e.g. parameter range is 0 to 30).
1.3.6.1.4.1.2544.1.12.19.1.5.1.3Unsigned32read-writecurrent
f3Pwe3SatopTable
OBJECT-TYPE
A list of entries corresponding to the PWE3 SAToP entities.
1.3.6.1.4.1.2544.1.12.19.1.6not-accessiblecurrent
f3Pwe3SatopEntry
OBJECT-TYPE
An entry containing information applicable to a particular PWE3 SAToP Entity.
1.3.6.1.4.1.2544.1.12.19.1.6.1not-accessiblecurrent
f3Pwe3SatopIndex
OBJECT-TYPE
Unique index value associated with the SAToP Entity.
1.3.6.1.4.1.2544.1.12.19.1.6.1.1Integer32not-accessiblecurrent
f3Pwe3SatopAlias
OBJECT-TYPE
This object allows SNMP management entities to provide an alias to the PWE3 SAToP entity.
1.3.6.1.4.1.2544.1.12.19.1.6.1.2DisplayString (SIZE(0..256))read-createcurrent
f3Pwe3SatopAdminState
OBJECT-TYPE
This object represents the Administrative State of the PWE3 SAToP entity.
1.3.6.1.4.1.2544.1.12.19.1.6.1.3AdminStateread-writecurrent
f3Pwe3SatopOperationalState
OBJECT-TYPE
This object represents the Operational State of the PWE3 SAToP entity.
1.3.6.1.4.1.2544.1.12.19.1.6.1.4OperationalStateread-onlycurrent
f3Pwe3SatopSecondaryState
OBJECT-TYPE
This object represents the Secondary State of the PWE3 SAToP entity.
1.3.6.1.4.1.2544.1.12.19.1.6.1.5SecondaryStateread-onlycurrent
f3Pwe3SatopTDMEntity
OBJECT-TYPE
This object allows specification of the T1/E1 entity associated with the SAToP. This is only used at SATop creation time. Result of get operation on this object will result with zeroDotZero since one Satop could have more then one associated TDM entity. Subsequently, the associated TDM entities are managed via f3Pwe3SatopTDMEntityTable.
1.3.6.1.4.1.2544.1.12.19.1.6.1.6VariablePointerread-createcurrent
f3Pwe3SatopDiscoveryType
OBJECT-TYPE
This object allows ability to statically/dynamically determine the MAC address of the remote IP Address associated with the SAToP. In the case of static discovery type, f3Pwe3SatopRemoteMacAddress must be explicitly specified. In the case of dynamic discovery, the system will use ARP mechanism to obtain the remote Layer 2 MAC address.
1.3.6.1.4.1.2544.1.12.19.1.6.1.7PWE3SatopDiscoveryTyperead-createcurrent
f3Pwe3SatopRemoteIpAddress
OBJECT-TYPE
This object allows ability to specify the remote IP Address. This is used in the PWE payload.
1.3.6.1.4.1.2544.1.12.19.1.6.1.8IpAddressread-createcurrent
f3Pwe3SatopRemoteMacAddress
OBJECT-TYPE
This object allows ability to specify the remote Layer 2 MAC Address. This must be specified in case of f3Pwe3SatopDiscoveryType as static. This is derived dynamically (via ARP) if f3Pwe3SatopDiscoveryType is dynamic, i.e. it does not have to be specified.
1.3.6.1.4.1.2544.1.12.19.1.6.1.9MacAddressread-createcurrent
f3Pwe3SatopEncapsulationType
OBJECT-TYPE
This object allows ability to specify the encapsulation type of the SATop. It can be encapsulated with VLAN and single MPLS label(vlan-one-mpls-label), VLAN and two MPLS labels (vlan-two-mpls-label), untagged and two MPLS labels (novlan-two-mpls-label) .
1.3.6.1.4.1.2544.1.12.19.1.6.1.10PWE3SatopEncapsulationTyperead-createcurrent
f3Pwe3SatopRTPEnabled
OBJECT-TYPE
This object enables/disables RTP header for this SATop instance.
1.3.6.1.4.1.2544.1.12.19.1.6.1.11TruthValueread-createcurrent
f3Pwe3SatopRTPUpdateFrequency
OBJECT-TYPE
When f3Pwe3SatopRTPEnabled is true, this object allows specification of the RTP clock update frequency.
1.3.6.1.4.1.2544.1.12.19.1.6.1.12PWE3SatopRTPTSUpdateFreqTyperead-createcurrent
f3Pwe3SatopControlWordEnabled
OBJECT-TYPE
This object is used for 3rd party interoperability, since earlier versions of PWE do not support control-word.
1.3.6.1.4.1.2544.1.12.19.1.6.1.13TruthValueread-createcurrent
f3Pwe3SatopJitterBufferSize
OBJECT-TYPE
This object allows definition of size of the jitter buffer in microseconds for this SATop instance.
1.3.6.1.4.1.2544.1.12.19.1.6.1.14Unsigned32read-createcurrent
f3Pwe3SatopPayloadSize
OBJECT-TYPE
This object allows specification of the SATop payload size.
1.3.6.1.4.1.2544.1.12.19.1.6.1.15Unsigned32read-createcurrent
f3Pwe3SatopVlanId
OBJECT-TYPE
This object allows specification of the SATop VLAN Id. Applicable for vlan based encapsulation types.
1.3.6.1.4.1.2544.1.12.19.1.6.1.16VlanIdread-createcurrent
f3Pwe3SatopVlanPriority
OBJECT-TYPE
This object allows specification of the SATop VLAN Priority. Applicable for vlan based encapsulation types.
1.3.6.1.4.1.2544.1.12.19.1.6.1.17VlanPriorityread-createcurrent
f3Pwe3SatopRxMplsLabel1
OBJECT-TYPE
This object allows specification of the expected receive MPLS Label. Applicable for single MPLS label encapsulation type.
1.3.6.1.4.1.2544.1.12.19.1.6.1.18MplsLabelread-createcurrent
f3Pwe3SatopRxMplsLabel2
OBJECT-TYPE
This object allows specification of the expected receive MPLS Label. Applicable for dual MPLS label encapsulation types.
1.3.6.1.4.1.2544.1.12.19.1.6.1.19MplsLabelread-createcurrent
f3Pwe3SatopTxMplsLabel1
OBJECT-TYPE
This object allows specification of the transmitted MPLS Label, used for multiplexing. Applicable for single MPLS label encapsulation type.
1.3.6.1.4.1.2544.1.12.19.1.6.1.20MplsLabelread-createcurrent
f3Pwe3SatopTxMplsLabel2
OBJECT-TYPE
This object allows specification of the transmitted MPLS Label, used for multiplexing. Applicable for dual MPLS label encapsulation type.
1.3.6.1.4.1.2544.1.12.19.1.6.1.21MplsLabelread-createcurrent
f3Pwe3SatopAisStabilizationProfile
OBJECT-TYPE
This object allows specification of the AIS stabilization Profile object. If no profile is associated, this value should be 0.0.
1.3.6.1.4.1.2544.1.12.19.1.6.1.22VariablePointerread-createcurrent
f3Pwe3SatopResyncProfile
OBJECT-TYPE
This object allows specification of the Resync Profile object. If no profile is associated, this value should be 0.0.
1.3.6.1.4.1.2544.1.12.19.1.6.1.23VariablePointerread-createcurrent
f3Pwe3SatopLossProfile
OBJECT-TYPE
This object allows specification of the Loss Profile object. If no profile is associated, this value should be 0.0.
1.3.6.1.4.1.2544.1.12.19.1.6.1.24VariablePointerread-createcurrent
f3Pwe3SatopTransportMode
OBJECT-TYPE
This object allows specification of the SATop transport mode.
1.3.6.1.4.1.2544.1.12.19.1.6.1.25PWE3SatopTransportModeread-createcurrent
f3Pwe3SatopStorageType
OBJECT-TYPE
The type of storage configured for this entry.
1.3.6.1.4.1.2544.1.12.19.1.6.1.26StorageTyperead-createcurrent
f3Pwe3SatopRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3Pwe3SatopRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3Pwe3SatopRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3Pwe3SatopRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.19.1.6.1.27RowStatusread-createcurrent
f3Pwe3SatopTDMEntitiesTable
OBJECT-TYPE
A list of entries corresponding to the PWE3 SATop TDM entities .
1.3.6.1.4.1.2544.1.12.19.1.7not-accessiblecurrent
f3Pwe3SatopTDMEntitiesEntry
OBJECT-TYPE
An entry containing information applicable to a particular PWE3 SATop TDM entity.
1.3.6.1.4.1.2544.1.12.19.1.7.1not-accessiblecurrent
f3Pwe3SatopTDMEntityIndex
OBJECT-TYPE
Unique index value associated with the PWE3 SATOP TDM Entity.
1.3.6.1.4.1.2544.1.12.19.1.7.1.1Integer32not-accessiblecurrent
f3Pwe3SatopTDMEntityObject
OBJECT-TYPE
This object points to the PWE3 SATOP TDM Entity. This is OID of the actual T1/E1 interface.
1.3.6.1.4.1.2544.1.12.19.1.7.1.2VariablePointerread-writecurrent
f3Pwe3SatopTDMEntityStorageType
OBJECT-TYPE
The type of storage configured for this entry.
1.3.6.1.4.1.2544.1.12.19.1.7.1.3StorageTyperead-createcurrent
f3Pwe3SatopTDMEntityRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3Pwe3SatopTDMEntityRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3Pwe3SatopTDMEntityRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3Pwe3SatopTDMEntityRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.19.1.7.1.4RowStatusread-createcurrent
f3Pwe3PerformanceObjects
OBJECT-IDENTITY
1.3.6.1.4.1.2544.1.12.19.2
f3Pwe3SatopStatsTable
OBJECT-TYPE
The PWE3 SATop Current data.
1.3.6.1.4.1.2544.1.12.19.2.1not-accessiblecurrent
f3Pwe3SatopStatsEntry
OBJECT-TYPE
A conceptual row in the f3Pwe3SatopStatsTable.
1.3.6.1.4.1.2544.1.12.19.2.1.1not-accessiblecurrent
f3Pwe3SatopStatsIndex
OBJECT-TYPE
An index of the SATop current bin.
1.3.6.1.4.1.2544.1.12.19.2.1.1.1Integer32 (1..65535)not-accessiblecurrent
f3Pwe3SatopStatsIntervalType
OBJECT-TYPE
Indicates the type of collection, i.e. whether it is 15 Min, 1 Day.
1.3.6.1.4.1.2544.1.12.19.2.1.1.2CmPmIntervalTyperead-onlycurrent
f3Pwe3SatopStatsValid
OBJECT-TYPE
Indicates the validity of the bin.
1.3.6.1.4.1.2544.1.12.19.2.1.1.3TruthValueread-onlycurrent
f3Pwe3SatopStatsAction
OBJECT-TYPE
Allows the Manager to clear the bin.
1.3.6.1.4.1.2544.1.12.19.2.1.1.4CmPmBinActionread-writecurrent
f3Pwe3SatopStatsESs
OBJECT-TYPE
The counter associated with the number of Errored Seconds encountered by the SATop in the current bin.
1.3.6.1.4.1.2544.1.12.19.2.1.1.5PerfCounter64read-onlycurrent
f3Pwe3SatopStatsSESs
OBJECT-TYPE
The counter associated with the number of Severely Errored Seconds encountered by the SATop in the current bin.
1.3.6.1.4.1.2544.1.12.19.2.1.1.6PerfCounter64read-onlycurrent
f3Pwe3SatopStatsEBs
OBJECT-TYPE
The counter associated with the number of Errored Blocsk encountered by the SATop in the current bin.
1.3.6.1.4.1.2544.1.12.19.2.1.1.7PerfCounter64read-onlycurrent
f3Pwe3SatopStatsResyncs
OBJECT-TYPE
The counter associated with the number of Resync count events encountered by the SATop in the current bin.
1.3.6.1.4.1.2544.1.12.19.2.1.1.8PerfCounter64read-onlycurrent
f3Pwe3SatopStatsMaxJitter
OBJECT-TYPE
The maximum absolute jitter on SATop in the current bin.
1.3.6.1.4.1.2544.1.12.19.2.1.1.9Unsigned32read-onlycurrent
f3Pwe3SatopStatsFramesTx
OBJECT-TYPE
The counter associated with the number of Frames Transmitted in the current bin.
1.3.6.1.4.1.2544.1.12.19.2.1.1.10PerfCounter64read-onlycurrent
f3Pwe3SatopStatsPayloadOctetsTx
OBJECT-TYPE
The counter associated with the number of Payload Octets Transmitted in the current bin.
1.3.6.1.4.1.2544.1.12.19.2.1.1.11PerfCounter64read-onlycurrent
f3Pwe3SatopStatsFramesRx
OBJECT-TYPE
The counter associated with the number of Frames Received in the current bin.
1.3.6.1.4.1.2544.1.12.19.2.1.1.12PerfCounter64read-onlycurrent
f3Pwe3SatopStatsPayloadOctetsRx
OBJECT-TYPE
The counter associated with the number of Payload Octets Received in the current bin.
1.3.6.1.4.1.2544.1.12.19.2.1.1.13PerfCounter64read-onlycurrent
f3Pwe3SatopStatsOutOfSeqFramesRx
OBJECT-TYPE
The counter associated with the number of Out of Sequence Frames Received in the current bin.
1.3.6.1.4.1.2544.1.12.19.2.1.1.14PerfCounter64read-onlycurrent
f3Pwe3SatopStatsLostFrames
OBJECT-TYPE
The counter associated with the number of Lost Frames detected in the current bin.
1.3.6.1.4.1.2544.1.12.19.2.1.1.15PerfCounter64read-onlycurrent
f3Pwe3SatopStatsLostFramesStateTrans
OBJECT-TYPE
The counter associated with the number of transitions to Lost Frame State detected in the current bin.
1.3.6.1.4.1.2544.1.12.19.2.1.1.16PerfCounter64read-onlycurrent
f3Pwe3SatopStatsMalformedFramesRx
OBJECT-TYPE
The counter associated with the number of Malformed Frames received in the current bin.
1.3.6.1.4.1.2544.1.12.19.2.1.1.17PerfCounter64read-onlycurrent
f3Pwe3SatopStatsJitterBufferLateFrames
OBJECT-TYPE
The counter associated with the number of Jitter Buffer Late Frames in the current bin.
1.3.6.1.4.1.2544.1.12.19.2.1.1.18PerfCounter64read-onlycurrent
f3Pwe3SatopHistoryTable
OBJECT-TYPE
The PWE3 SATop History data.
1.3.6.1.4.1.2544.1.12.19.2.2not-accessiblecurrent
f3Pwe3SatopHistoryEntry
OBJECT-TYPE
A conceptual row in the f3Pwe3SatopHistoryTable.
1.3.6.1.4.1.2544.1.12.19.2.2.1not-accessiblecurrent
f3Pwe3SatopHistoryIndex
OBJECT-TYPE
An index of the SATop current bin.
1.3.6.1.4.1.2544.1.12.19.2.2.1.1Integer32 (1..65535)not-accessiblecurrent
f3Pwe3SatopHistoryTime
OBJECT-TYPE
Indicates the time of history bin creation.
1.3.6.1.4.1.2544.1.12.19.2.2.1.2DateAndTimeread-onlycurrent
f3Pwe3SatopHistoryValid
OBJECT-TYPE
Indicates the validity of the bin.
1.3.6.1.4.1.2544.1.12.19.2.2.1.3TruthValueread-onlycurrent
f3Pwe3SatopHistoryAction
OBJECT-TYPE
Allows the Manager to clear the bin.
1.3.6.1.4.1.2544.1.12.19.2.2.1.4CmPmBinActionread-writecurrent
f3Pwe3SatopHistoryESs
OBJECT-TYPE
The counter associated with the number of Errored Seconds encountered by the SATop in the current bin.
1.3.6.1.4.1.2544.1.12.19.2.2.1.5PerfCounter64read-onlycurrent
f3Pwe3SatopHistorySESs
OBJECT-TYPE
The counter associated with the number of Severely Errored Seconds encountered by the SATop in the current bin.
1.3.6.1.4.1.2544.1.12.19.2.2.1.6PerfCounter64read-onlycurrent
f3Pwe3SatopHistoryEBs
OBJECT-TYPE
The counter associated with the number of Errored Blocsk encountered by the SATop in the current bin.
1.3.6.1.4.1.2544.1.12.19.2.2.1.7PerfCounter64read-onlycurrent
f3Pwe3SatopHistoryResyncs
OBJECT-TYPE
The counter associated with the number of Resync count events encountered by the SATop in the current bin.
1.3.6.1.4.1.2544.1.12.19.2.2.1.8PerfCounter64read-onlycurrent
f3Pwe3SatopHistoryMaxJitter
OBJECT-TYPE
The maximum absolute jitter on SATop in the current bin.
1.3.6.1.4.1.2544.1.12.19.2.2.1.9Unsigned32read-onlycurrent
f3Pwe3SatopHistoryFramesTx
OBJECT-TYPE
The counter associated with the number of Frames Transmitted in the current bin.
1.3.6.1.4.1.2544.1.12.19.2.2.1.10PerfCounter64read-onlycurrent
f3Pwe3SatopHistoryPayloadOctetsTx
OBJECT-TYPE
The counter associated with the number of Payload Octets Transmitted in the current bin.
1.3.6.1.4.1.2544.1.12.19.2.2.1.11PerfCounter64read-onlycurrent
f3Pwe3SatopHistoryFramesRx
OBJECT-TYPE
The counter associated with the number of Frames Received in the current bin.
1.3.6.1.4.1.2544.1.12.19.2.2.1.12PerfCounter64read-onlycurrent
f3Pwe3SatopHistoryPayloadOctetsRx
OBJECT-TYPE
The counter associated with the number of Payload Octets Received in the current bin.
1.3.6.1.4.1.2544.1.12.19.2.2.1.13PerfCounter64read-onlycurrent
f3Pwe3SatopHistoryOutOfSeqFramesRx
OBJECT-TYPE
The counter associated with the number of Out of Sequence Frames Received in the current bin.
1.3.6.1.4.1.2544.1.12.19.2.2.1.14PerfCounter64read-onlycurrent
f3Pwe3SatopHistoryLostFrames
OBJECT-TYPE
The counter associated with the number of Lost Frames detected in the current bin.
1.3.6.1.4.1.2544.1.12.19.2.2.1.15PerfCounter64read-onlycurrent
f3Pwe3SatopHistoryLostFramesStateTrans
OBJECT-TYPE
The counter associated with the number of transitions to Lost Frame State detected in the current bin.
1.3.6.1.4.1.2544.1.12.19.2.2.1.16PerfCounter64read-onlycurrent
f3Pwe3SatopHistoryMalformedFramesRx
OBJECT-TYPE
The counter associated with the number of Malformed Frames received in the current bin.
1.3.6.1.4.1.2544.1.12.19.2.2.1.17PerfCounter64read-onlycurrent
f3Pwe3SatopHistoryJitterBufferLateFrames
OBJECT-TYPE
The counter associated with the number of Jitter Buffer Overruns in the current bin.
1.3.6.1.4.1.2544.1.12.19.2.2.1.18PerfCounter64read-onlycurrent
f3Pwe3SatopThresholdTable
OBJECT-TYPE
A table of entries that allow manageability of SATop Thresholds.
1.3.6.1.4.1.2544.1.12.19.2.3not-accessiblecurrent
f3Pwe3SatopThresholdEntry
OBJECT-TYPE
A conceptual row in the f3Pwe3SatopThresholdTable.
1.3.6.1.4.1.2544.1.12.19.2.3.1not-accessiblecurrent
f3Pwe3SatopThresholdIndex
OBJECT-TYPE
An index that uniquely identifies an entry in the f3Pwe3SatopThresholdTable.
1.3.6.1.4.1.2544.1.12.19.2.3.1.1Integer32 (1..65535)not-accessiblecurrent
f3Pwe3SatopThresholdInterval
OBJECT-TYPE
The interval over which monitored value is sampled and compared with the specified threshold.
1.3.6.1.4.1.2544.1.12.19.2.3.1.2CmPmIntervalTyperead-onlycurrent
f3Pwe3SatopThresholdVariable
OBJECT-TYPE
The object identifier of the particular variable to be sampled.
1.3.6.1.4.1.2544.1.12.19.2.3.1.3VariablePointerread-onlycurrent
f3Pwe3SatopThresholdValueLo
OBJECT-TYPE
Lower 32 bits of the threshold value.
1.3.6.1.4.1.2544.1.12.19.2.3.1.4Unsigned32read-writecurrent
f3Pwe3SatopThresholdValueHi
OBJECT-TYPE
Higher 32 bits of the threshold value.
1.3.6.1.4.1.2544.1.12.19.2.3.1.5Unsigned32read-writecurrent
f3Pwe3SatopThresholdMonValue
OBJECT-TYPE
Monitored value corresponding to f3Pwe3SatopThresholdVariable.
1.3.6.1.4.1.2544.1.12.19.2.3.1.6Counter64read-onlycurrent
f3Pwe3PerformanceNotifications
OBJECT-IDENTITY
1.3.6.1.4.1.2544.1.12.19.3
f3Pwe3Conformance
OBJECT-IDENTITY
1.3.6.1.4.1.2544.1.12.19.4
f3Pwe3Compliances
OBJECT-IDENTITY
1.3.6.1.4.1.2544.1.12.19.4.1
f3Pwe3Groups
OBJECT-IDENTITY
1.3.6.1.4.1.2544.1.12.19.4.2

Notifications

NameOIDStatus
f3Pwe3SatopThresholdCrossingAlert
NOTIFICATION-TYPE
This trap is sent each time a threshold on a PM condition on an PWE3 SATop is crossed.
1.3.6.1.4.1.2544.1.12.19.3.1current

Conformance

NameOIDStatus
f3Pwe3Compliance
MODULE-COMPLIANCE
Describes the requirements for conformance to the F3 PWE3 group.
1.3.6.1.4.1.2544.1.12.19.4.1.1current
f3Pwe3ObjectGroup
OBJECT-GROUP
A collection of objects used to manage the F3 PWE3 Configuration data.
1.3.6.1.4.1.2544.1.12.19.4.2.1current
f3Pwe3PerfObjectGroup
OBJECT-GROUP
A collection of objects used to manage the F3 PWE3 Performance data.
1.3.6.1.4.1.2544.1.12.19.4.2.2current
f3Pwe3PerfNotifGroup
NOTIFICATION-GROUP
A collection of notifications related to F3 PWE3 Threshold Crossing Alerts.
1.3.6.1.4.1.2544.1.12.19.4.2.3current