MIBs Depot

F3-L3-MIB

Registered at
1.3.6.1.4.1.2544.1.12.37
Last updated
2018-10-25 00:00
Organization
ADVA Optical Networking SE
Revisions
2018-10-25 00:00
Namespace
adva
Source file
F3-L3-MIB
Digest
sha256:ec7fa5f29d6f3ef03d3b0ef55fcc79979301d4cdb0e1dc3a71ee6b95dfbc8642

Description

This module defines the L3 MIB definitions used by the F3 (FSP150CM/CC) product lines. Copyright (C) ADVA.

Contact

Web URL: http://adva.com/ E-mail: support@adva.com Postal: ADVA Optical Networking SE Campus Martinsried Fraunhoferstrasse 9a 82152 Martinsried/Munich Germany Phone: +49 089 89 06 65 0 Fax: +49 089 89 06 65 199

Imports

FromSymbols
ADVA-MIBfsp150cm
CM-COMMON-MIBAdminState, CmPmBinAction, CmPmIntervalType, F3DisplayString, FlowSecState, IpVersion, OperationalState, PerfCounter64, SecondaryState, TrafficDirection, VlanId, VlanPriority
CM-ENTITY-MIBneIndex, shelfIndex, slotIndex
CM-FACILITY-MIBAclNoMatchDispositionType, PolicerAlgorithmType, PolicerColorMode, ShapingType
CM-IP-MIBCmDhcpRole, DHCPCIDType, DHCPHostNameType, IpEntryType, IpMode
ENTITY-MIBPhysicalIndex
IF-MIBInterfaceIndex, ifIndex
IPV6-TCIpv6Address
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP
SNMPv2-SMICounter64, Integer32, IpAddress, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, Unsigned32, iso
SNMPv2-TCDateAndTime, DisplayString, MacAddress, RowStatus, StorageType, TEXTUAL-CONVENTION, TruthValue, VariablePointer

Imported by

1 module(s) in this corpus import this one.

Load order

Every file a consumer needs in order to load this module, dependencies first.

ADVA-MIB
CM-COMMON-MIB
CM-ENTITY-MIB
CM-FACILITY-MIB
CM-IP-MIB
CM-REDUNDANCY-MIB
CM-SYSTEM-MIB
ENTITY-MIB
F3-L3-MIB
F3-LAG-MIB
F3-SYNC-MIB
IANA-ADDRESS-FAMILY-NUMBERS-MIB
IANA-ENTITY-MIB
IANAifType-MIB
IF-MIB
IPV6-TC
LLDP-V2-MIB
LLDP-V2-TC-MIB
RFC1158-MIB
RFC1271-MIB
RMON-MIB
RMON2-MIB
SNMP-FRAMEWORK-MIB
SNMP-TARGET-MIB
SNMPv2-CONF
SNMPv2-MIB
SNMPv2-SMI
SNMPv2-TC
TOKEN-RING-RMON-MIB
UUID-TC-MIB

Textual conventions

NameOIDSyntaxAccessStatus
AclRuleL2Side
TEXTUAL-CONVENTION
Describes the acl rule l2 side.
current
AffectiveArpActionType
TEXTUAL-CONVENTION
Describes the retrieve effective arp action.
deprecated
BgpGracefulRestartControlType
TEXTUAL-CONVENTION
.
current
BgpNextHopUpdateType
TEXTUAL-CONVENTION
.
current
BgpPeerAddressFamilyNameType
TEXTUAL-CONVENTION
.
current
BgpRouteFilterDirection
TEXTUAL-CONVENTION
Config parameters related to inbound or outbound route filter.
current
BgpRouterActionType
TEXTUAL-CONVENTION
Describes the action on BGP Router.
current
BgpSessionStateType
TEXTUAL-CONVENTION
Operational state of the BGP peer. idle (1) -- Neighbor is down, and in the Idle state of the FSM. connect (2) -- Neighbor is down, and the session is waiting for the underlying transport session to be established. active (3) -- Neighbor is down, and the local system is awaiting a conncetion from the remote peer. openSent (4) -- Neighbor is in the process of being established. The local system has sent an OPEN message. openConfirm (5) -- Neighbor is in the process of being established. The local system is awaiting a NOTIFICATION or KEEPALIVE message. established (6) -- Neighbor is up - the BGP session with the peer is established.
current
BgpUpdateSourceType
TEXTUAL-CONVENTION
The type to update source IP.
current
DhcpRelayInterfaceSide
TEXTUAL-CONVENTION
Describes the DHCP relay interface side.
current
EcmpDistributionType
TEXTUAL-CONVENTION
.
current
IfIpAddressSourceType
TEXTUAL-CONVENTION
Describes the Ip Interface adress source type.
current
IpInterfaceType
TEXTUAL-CONVENTION
Describes IPv6 interface type.
current
IpPrefixDispositionType
TEXTUAL-CONVENTION
IP Prefix Disposition Type.
current
Ipv6AddressAssignMode
TEXTUAL-CONVENTION
Describes IPv6 address assignment mode.
current
Ipv6LinkLocalAddressMode
TEXTUAL-CONVENTION
IPv6 address shall be first 64 bits as configured in IPv6 unicast address auto generation prefix followed by Interface ID.
current
L3AclRuleOperation
TEXTUAL-CONVENTION
Describes the acl rule operation.
current
NdpNeighborReachabilityState
TEXTUAL-CONVENTION
Reachability state of NDP entry.
current
NdpRaDefaultRouterPreference
TEXTUAL-CONVENTION
Describes Router preference.
current
OspfAdjacencyState
TEXTUAL-CONVENTION
OSPF Interface Adjacency State. down (1) -- Neighbor down state. attempt (2) -- Neighbor attempt state. init (3) -- Neighbor init state. twoWay (4) -- Neighbor 2-Way state. exStart (5) -- Neighbor exchange start state. exchange (6) -- Neighbor exchange state. loading (7) -- Neighbor loading state. full (8) -- Neighbor full state.
current
OspfAsLsaType
TEXTUAL-CONVENTION
Type of LSA from external AS. asExternal (1) -- Autonomous system external LSA. asOpaque (2) -- OSPF AS (Autonomous System) Scope Opaque LSA.
current
OspfAuthType
TEXTUAL-CONVENTION
This attribute is used to specify authentication type. Simple: 64-bits clear password inserted into OSPF packets header. None: No authentication is used. Cryptographic: a shared secret which enables the generation/verification of message digests which are appended to the OSPF protocol packets. none (1) -- No authentication. simple (2) -- 64-bits clear password inserted into OSPF packets header. cryptoGraphic (3) -- A shared secret which enables the generation/verification of message digests which are appended to the OSPF protocol packets. System level authentication key is used.
current
OspfIfType
TEXTUAL-CONVENTION
The network type connected by interface. broadcast (1) -- Broadcast. pointToPoint (2) -- Point to Point.
current
OspfInterfaceState
TEXTUAL-CONVENTION
The OSPF state of interface. down (1) -- In this state, the lower-level protocols have indicated that the interface is unusable. loopback (2) -- The interface is looped back and unavailable for regular data traffic. waiting (3), -- In this state, the router is trying to determine the identity of the (Backup) Designated Router for the network. To do this, the router monitors the Hello Packets it receives. The router is not allowed to elect a Backup Designated Router nor a Designated Router until it transitions out of Waiting state. This prevents unnecessary changes of (Backup) Designated Router. pointToPoint (4), -- In this state, the interface is operational, and connects either to a physical point-to-point network or to a virtual link. Upon entering this state, the router attempts to form an adjacency with the neighboring router. Hello Packets are sent to the neighbor every HelloInterval seconds. drOther (5), -- The interface is to a broadcast or NBMA network on which another router has been selected to be the Designated Router. In this state, the router itself has not been selected Backup Designated Router either. The router forms adjacencies to both the Designated Router and the Backup Designated Router (if they exist). dr (6), -- In this state, this router itself is the Designated Router on the attached network. backup (7) -- In this state, the router itself is the Backup Designated Router on the attached network.
current
OspfLsaType
TEXTUAL-CONVENTION
Type of LSA from external AS. router (1) -- Router LSA: The Router LSA is generated by each router for each area it is located. In the link-state ID you will find the originating router's ID. network (2) -- Network LSA: Network LSAs are generated by the DR. The link-state ID will be the router ID of the DR. summary (3) -- Summary LSA: The summary LSA is created by the ABR and flooded into other areas. asExternal (4) -- External LSA: Also known as autonomous system external LSA, the external LSAs are generated by the ASBR. areaOpaque (5) -- Packets are used to flood OSPF information through other area routers even if these routers do not process this information in order to extend OSPF functionality, this LSA is used for traffic engineering to advertise MPLS and other protocols.
current
OspfRouterActionType
TEXTUAL-CONVENTION
Describes the action on OSPF Router.
current
OspfVersion
TEXTUAL-CONVENTION
Describes version of a Ospf Router.
current
RouteFlags
TEXTUAL-CONVENTION
Describes the traffci ipv4 route flags.
current
RoutesMetricType
TEXTUAL-CONVENTION
Metric Type for routes exported from external autonomous system. e1 (1) -- Type 1 external metrics are equivalent to the link-state metric, where the cost is equal to the sum of the internal costs plus the external cost. This means that Type 1 external metrics include the external cost to the destination as well as the cost (metric) to reach the AS boundary router. e2 (2) -- Type 2 external metrics are greater than the cost of any path internal to the AS. Type 2 external metrics use only the external cost to the destination and ignore the cost (metric) to reach the AS boundary router.
current
SrSidType
TEXTUAL-CONVENTION
SID Type.
current
TilfaProtectionType
TEXTUAL-CONVENTION
TI-LFA Protection Type.
current
TrafficIpInterfaceActionType
TEXTUAL-CONVENTION
Describes interface action.
current
TrafficIpRouteOriginType
TEXTUAL-CONVENTION
The origin type of IP Route. bgp (1) -- From BGP. ospf (2) -- From OSPF. connected (3) -- Connected Route. static (4) -- Configured. dhcp (5) -- From DHCP Relay. slaac (6) -- From SLACC. dhcp-relay (7) -- From DHCP. isis (8) -- From ISIS. ti-lfa (9) -- From TI-LFA.
current
TrafficIpRouteStatus
TEXTUAL-CONVENTION
Describes the traffci ipv4 route status.
deprecated
TrafficIpRouteStatusType
TEXTUAL-CONVENTION
Describes the traffci ipv4 route status.
current
TrafficIpv6InterfaceActionType
TEXTUAL-CONVENTION
Describes interface action.
current
TrafficOspfAreaType
TEXTUAL-CONVENTION
Area Type.
current
TrafficOspfRole
TEXTUAL-CONVENTION
The role of router. dr (1) -- Designated Router. bdr (2) -- Backup DR. drother (3) -- DR Other. pointToPoint(4) -- Point to point
current
VrfAction
TEXTUAL-CONVENTION
Describes the action on Vrf.
deprecated
VrfActionType
TEXTUAL-CONVENTION
Describes the action on Vrf.
current
VrfTransportType
TEXTUAL-CONVENTION
Transport Type.
current

Objects

NameOIDSyntaxAccessStatus
f3L3Objects
OBJECT-IDENTITY
1.3.6.1.4.1.2544.1.12.37.1
f3DhcpRelayAgentTable
OBJECT-TYPE
A list of entries for the Dhcp Relay Agent.
1.3.6.1.4.1.2544.1.12.37.1.1not-accessiblecurrent
f3DhcpRelayAgentEntry
OBJECT-TYPE
A conceptual row in the f3DhcpRelayAgentTable.
1.3.6.1.4.1.2544.1.12.37.1.1.1not-accessiblecurrent
f3DhcpRelayAgentIndex
OBJECT-TYPE
The index of the DHCP relay agent entry.
1.3.6.1.4.1.2544.1.12.37.1.1.1.1Integer32not-accessiblecurrent
f3DhcpRelayAgentAlias
OBJECT-TYPE
The DHCP relay agent alias.
1.3.6.1.4.1.2544.1.12.37.1.1.1.2F3DisplayString (SIZE(0..256))read-writecurrent
f3DhcpRelayAgentAdminState
OBJECT-TYPE
The admin state of this DCHP relay agent.
1.3.6.1.4.1.2544.1.12.37.1.1.1.3AdminStateread-writecurrent
f3DhcpRelayAgentSecondaryState
OBJECT-TYPE
The secondary state of this DCHP relay agent.
1.3.6.1.4.1.2544.1.12.37.1.1.1.4SecondaryStateread-onlycurrent
f3DhcpRelayAgentOperationalState
OBJECT-TYPE
The operational state of this DCHP relay agent.
1.3.6.1.4.1.2544.1.12.37.1.1.1.5OperationalStateread-onlycurrent
f3DhcpRelayAgentIpVersion
OBJECT-TYPE
The Ip version of this DCHP relay agent.
1.3.6.1.4.1.2544.1.12.37.1.1.1.6IpVersionread-writecurrent
f3DhcpRelayAgentServerIpAddress
OBJECT-TYPE
The Ipv4 address of this DCHP relay agent.
1.3.6.1.4.1.2544.1.12.37.1.1.1.7IpAddressread-writecurrent
f3DhcpRelayAgentOp82SubOp9ControlEnabled
OBJECT-TYPE
This object describes the suboption9 of the option82 whether enabled.
1.3.6.1.4.1.2544.1.12.37.1.1.1.8TruthValueread-writecurrent
f3DhcpRelayAgentOp82SubOp9Value
OBJECT-TYPE
This object describes the vendor string if the suboption9 enabled.
1.3.6.1.4.1.2544.1.12.37.1.1.1.9DisplayString (SIZE(0..255))read-writecurrent
f3DhcpRelayAgentStorageType
OBJECT-TYPE
The type of storage configured for this entry.
1.3.6.1.4.1.2544.1.12.37.1.1.1.10StorageTyperead-createcurrent
f3DhcpRelayAgentRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3DhcpRelayAgentRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3DhcpRelayAgentRowStatus value as createAndGo(4). Upon successful row creation, this variable has a value of active(1). The f3DhcpRelayAgentRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.37.1.1.1.11RowStatusread-createcurrent
f3VrfTable
OBJECT-TYPE
A list of entries for the VRF user.
1.3.6.1.4.1.2544.1.12.37.1.2not-accessiblecurrent
f3VrfEntry
OBJECT-TYPE
A conceptual row in the f3VrfTable.
1.3.6.1.4.1.2544.1.12.37.1.2.1not-accessiblecurrent
f3VrfIndex
OBJECT-TYPE
The vrf number.
1.3.6.1.4.1.2544.1.12.37.1.2.1.1Integer32not-accessiblecurrent
f3VrfAlias
OBJECT-TYPE
This object describes the vrf alias.
1.3.6.1.4.1.2544.1.12.37.1.2.1.2F3DisplayString (SIZE(0..256))read-writecurrent
f3VrfAdminState
OBJECT-TYPE
This object describes the vrf admin state.
1.3.6.1.4.1.2544.1.12.37.1.2.1.3AdminStateread-writecurrent
f3VrfSecondaryState
OBJECT-TYPE
This object describes the vrf secondary state.
1.3.6.1.4.1.2544.1.12.37.1.2.1.4SecondaryStateread-onlycurrent
f3VrfOperationalState
OBJECT-TYPE
This object describes the vrf operational state.
1.3.6.1.4.1.2544.1.12.37.1.2.1.5OperationalStateread-onlycurrent
f3VrfAccIsolationControlEnabled
OBJECT-TYPE
This object is used to control traffic between L3 flowpoint on Acc port.
1.3.6.1.4.1.2544.1.12.37.1.2.1.6OperationalStateread-writeobsolete
f3VrfPingIpv4Destination
OBJECT-TYPE
This object allows user to specify the IP Address to which ICMP Ping will be initiated.
1.3.6.1.4.1.2544.1.12.37.1.2.1.7IpAddressread-writecurrent
f3VrfTraceRouteIpv4Destination
OBJECT-TYPE
This object allows user to specify the IP Address to which Trace Route will be initiated.
1.3.6.1.4.1.2544.1.12.37.1.2.1.8IpAddressread-writecurrent
f3VrfAction
OBJECT-TYPE
The Vrf action, includes fluch ARP cache, ping, trace route. DEPRECATED and new variable to use is f3VrfActionX.
1.3.6.1.4.1.2544.1.12.37.1.2.1.9VrfActionread-writedeprecated
f3VrfPingResult
OBJECT-TYPE
The Ping action result.
1.3.6.1.4.1.2544.1.12.37.1.2.1.10F3DisplayStringread-onlycurrent
f3VrfTraceRouteResult
OBJECT-TYPE
The trace route action result.
1.3.6.1.4.1.2544.1.12.37.1.2.1.11F3DisplayStringread-onlycurrent
f3VrfStorageType
OBJECT-TYPE
The type of storage configured for this entry.
1.3.6.1.4.1.2544.1.12.37.1.2.1.12StorageTyperead-createcurrent
f3VrfRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3VrfRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3VrfRowStatus value as createAndGo(4). Upon successful row creation, this variable has a value of active(1). The f3VrfRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.37.1.2.1.13RowStatusread-createcurrent
f3VrfDhcpRoutesControl
OBJECT-TYPE
This object is used to control dynamic routes creation based on DHCP relay agent operation. if it is disabled, the vrf should not use host ip addresses assigned by means of DHCP relay agent for the dynamic routes creation.
1.3.6.1.4.1.2544.1.12.37.1.2.1.14TruthValueread-writecurrent
f3VrfActionX
OBJECT-TYPE
The Vrf action, includes ping, trace route and route retrieve
1.3.6.1.4.1.2544.1.12.37.1.2.1.15VrfActionTyperead-writecurrent
f3VrfActionIfName
OBJECT-TYPE
Interface Name parameter for the VRF action. For example, to flush ARP cache for a particular interface this variable shall be set and then f3VrfActionX shall be set to flushArpCache.
1.3.6.1.4.1.2544.1.12.37.1.2.1.16DisplayStringread-writecurrent
f3VrfIpVersion
OBJECT-TYPE
This object describes the vrf Ip version.
1.3.6.1.4.1.2544.1.12.37.1.2.1.17IpVersionread-createcurrent
f3VrfPingIpv6Destination
OBJECT-TYPE
This object allows user to specify the IP Address to which ICMP Ping will be initiated.
1.3.6.1.4.1.2544.1.12.37.1.2.1.18Ipv6Addressread-writecurrent
f3VrfTraceRouteIpv6Destination
OBJECT-TYPE
This object allows user to specify the IP Address to which Trace Route will be initiated.
1.3.6.1.4.1.2544.1.12.37.1.2.1.19Ipv6Addressread-writecurrent
f3VrfMaxFwdTableEntries
OBJECT-TYPE
This object defines the maximum forwarding table entries that can be used by the vrf
1.3.6.1.4.1.2544.1.12.37.1.2.1.20Integer32read-writecurrent
f3VrfFwdTableFull
OBJECT-TYPE
This is a status variable that indicates if the forwarding table for the vrf is full
1.3.6.1.4.1.2544.1.12.37.1.2.1.21TruthValueread-onlycurrent
f3VrfEcmpDistribution
OBJECT-TYPE
The fields in IP Packets used in hash lookup.
1.3.6.1.4.1.2544.1.12.37.1.2.1.22EcmpDistributionTyperead-writecurrent
f3VrfEcmpStaticRoutesMaximumPaths
OBJECT-TYPE
The maximum number of path used in ECMP for static routes.
1.3.6.1.4.1.2544.1.12.37.1.2.1.23Unsigned32read-writecurrent
f3VrfTransportType
OBJECT-TYPE
The transport type of this entry.
1.3.6.1.4.1.2544.1.12.37.1.2.1.24VrfTransportTyperead-createcurrent
f3L3FlowPointTable
OBJECT-TYPE
A list of entries for the L3 flowpoint.
1.3.6.1.4.1.2544.1.12.37.1.3not-accessiblecurrent
f3L3FlowPointEntry
OBJECT-TYPE
A conceptual row in the f3L3FlowPointTable.
1.3.6.1.4.1.2544.1.12.37.1.3.1not-accessiblecurrent
f3L3FlowPointPortTypeIndex
OBJECT-TYPE
It specifies the port type, value 1 means Network Port, value 2 means Access Port, value 3 means Mobile Traffic Port.
1.3.6.1.4.1.2544.1.12.37.1.3.1.1Integer32not-accessiblecurrent
f3L3FlowPointPortIndex
OBJECT-TYPE
The port number value.
1.3.6.1.4.1.2544.1.12.37.1.3.1.2Integer32not-accessiblecurrent
f3L3FlowPointIndex
OBJECT-TYPE
The L3 flow point number.
1.3.6.1.4.1.2544.1.12.37.1.3.1.3Integer32not-accessiblecurrent
f3L3FlowPointAlias
OBJECT-TYPE
This object describes the L3 flow point alias.
1.3.6.1.4.1.2544.1.12.37.1.3.1.4F3DisplayString (SIZE(0..256))read-writecurrent
f3L3FlowPointAdminState
OBJECT-TYPE
This object describes the L3 flow point admin state.
1.3.6.1.4.1.2544.1.12.37.1.3.1.5AdminStateread-writecurrent
f3L3FlowPointSecondaryState
OBJECT-TYPE
This object describes the L3 flow point secondary state.
1.3.6.1.4.1.2544.1.12.37.1.3.1.6SecondaryStateread-onlycurrent
f3L3FlowPointOperationalState
OBJECT-TYPE
This object describes the L3 flow point operational state.
1.3.6.1.4.1.2544.1.12.37.1.3.1.7OperationalStateread-onlycurrent
f3L3FlowPointMultiCOSEnabled
OBJECT-TYPE
Control to enable or disable per-COS BWPs on a FlowPoint. ENABLED:per-COS BWPs (CIR, EIR, CBS, EBS, CM, CF) are applied as a policing function for all ingress frames of this flowpoint. DISABLED:per-Flow BWP (CIR, EIR, CBS, EBS, CM, CF) is applied as a policing function for all ingress frames of this flowpoint. User must independently enable each COS BWP when ENABLED.
1.3.6.1.4.1.2544.1.12.37.1.3.1.8TruthValueread-writecurrent
f3L3FlowPointCOS
OBJECT-TYPE
Identifies the internal COS applied to all ingress frames of the flowpoint.
1.3.6.1.4.1.2544.1.12.37.1.3.1.9Integer32read-writecurrent
f3L3FlowPointUntaggedMemberShipEnabled
OBJECT-TYPE
This attribute controls untagged frames membership for the Flowpoint. ENABLED: Ingress untagged frame matches Flowpoint membership. DISABLED: Ingress untagged frame does not match Flowpoint membership.
1.3.6.1.4.1.2544.1.12.37.1.3.1.10TruthValueread-writecurrent
f3L3FlowPointOuterTagMemberShipEnabled
OBJECT-TYPE
This attribute controls outer tag membership for the Flowpoint whether enabled.
1.3.6.1.4.1.2544.1.12.37.1.3.1.11TruthValueread-writecurrent
f3L3FlowPointOuterTagMemberShipVlanId
OBJECT-TYPE
This attribute controls outer tag VlanId membership for the Flowpoint.
1.3.6.1.4.1.2544.1.12.37.1.3.1.12VlanIdread-writecurrent
f3L3FlowPointInnerTagMemberShipEnabled
OBJECT-TYPE
This attribute controls inner tag membership for the Flowpoint whether enabled.
1.3.6.1.4.1.2544.1.12.37.1.3.1.13TruthValueread-writecurrent
f3L3FlowPointInnerTagMemberShipVlanId
OBJECT-TYPE
This attribute controls inner tag VlanId membership for the Flowpoint.
1.3.6.1.4.1.2544.1.12.37.1.3.1.14VlanIdread-writecurrent
f3L3FlowPointFragmentedPktsFwdEnabled
OBJECT-TYPE
This attribute specifies whether received IP Packets with More Fragments flag should be forwarded by the FlowPoint.
1.3.6.1.4.1.2544.1.12.37.1.3.1.15TruthValueread-writecurrent
f3L3FlowPointHCosMgmtEnabled
OBJECT-TYPE
This attribute specifies whether the Hierarchical COS shaping enabled for this flow point.
1.3.6.1.4.1.2544.1.12.37.1.3.1.16TruthValueread-writecurrent
f3L3FlowPointHCosGuaranteedBwHi
OBJECT-TYPE
This attribute specifies the Hierarchical COS guarranteed bandwidth high 32 bits for this flow point.
1.3.6.1.4.1.2544.1.12.37.1.3.1.17Unsigned32read-writecurrent
f3L3FlowPointHCosGuaranteedBwLo
OBJECT-TYPE
This attribute specifies the Hierarchical COS guarranteed bandwidth low 32 bits for this flow point.
1.3.6.1.4.1.2544.1.12.37.1.3.1.18Unsigned32read-writecurrent
f3L3FlowPointHCosMaximumBwHi
OBJECT-TYPE
This attribute specifies the Hierarchical COS maximum bandwidth high 32 bits for this flow point.
1.3.6.1.4.1.2544.1.12.37.1.3.1.19Unsigned32read-writecurrent
f3L3FlowPointHCosMaximumBwLo
OBJECT-TYPE
This attribute specifies the Hierarchical COS maximum bandwidth low 32 bits for this flow point.
1.3.6.1.4.1.2544.1.12.37.1.3.1.20Unsigned32read-writecurrent
f3L3FlowPointPolicingEnabled
OBJECT-TYPE
This attribute allows enable or disable policers of the flow point.
1.3.6.1.4.1.2544.1.12.37.1.3.1.21TruthValueread-writecurrent
f3L3FlowPointStorageType
OBJECT-TYPE
The type of storage configured for this entry.
1.3.6.1.4.1.2544.1.12.37.1.3.1.22StorageTyperead-createcurrent
f3L3FlowPointRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3L3FlowPointRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3L3FlowPointRowStatus value as createAndGo(4). Upon successful row creation, this variable has a value of active(1). The f3L3FlowPointRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.37.1.3.1.23RowStatusread-createcurrent
f3L3FlowPointDscpOverwriteControl
OBJECT-TYPE
This attribute allows enable dscp value overwrite.
1.3.6.1.4.1.2544.1.12.37.1.3.1.24TruthValueread-writecurrent
f3L3FlowPointPriMapProfile
OBJECT-TYPE
This attribute allows specify the priority map profile.
1.3.6.1.4.1.2544.1.12.37.1.3.1.25VariablePointerread-writecurrent
f3L3FlowPointRefConnectGuardFlow
OBJECT-TYPE
This object specifies Mac Sec flow object OID.
1.3.6.1.4.1.2544.1.12.37.1.3.1.26VariablePointerread-createcurrent
f3L3FlowPointSecureState
OBJECT-TYPE
This object specifies the secure state of this flow.
1.3.6.1.4.1.2544.1.12.37.1.3.1.27FlowSecStateread-onlycurrent
f3L3FlowPointSecureBlockingEnabled
OBJECT-TYPE
This object can be used to enable/disable secure block.
1.3.6.1.4.1.2544.1.12.37.1.3.1.28TruthValueread-createcurrent
f3L3FlowPointWfqSegmentationCOS
OBJECT-TYPE
This object used to specify wfq segmentation COS value.
1.3.6.1.4.1.2544.1.12.37.1.3.1.29Integer32read-writecurrent
f3L3FlowPointWfqGroupCOS
OBJECT-TYPE
This object used to specify wfq group COS value.
1.3.6.1.4.1.2544.1.12.37.1.3.1.30Integer32read-writecurrent
f3L3FlowPointWfqGroupEirLo
OBJECT-TYPE
This object used to specify wfq group EIR low 32 bits value.
1.3.6.1.4.1.2544.1.12.37.1.3.1.31Unsigned32read-writecurrent
f3L3FlowPointWfqGroupEirHi
OBJECT-TYPE
This object used to specify wfq group EIR high 32 bits value.
1.3.6.1.4.1.2544.1.12.37.1.3.1.32Unsigned32read-writecurrent
f3L3FlowPointOuterVlanEthertype
OBJECT-TYPE
.
1.3.6.1.4.1.2544.1.12.37.1.3.1.33Integer32 (0..65535)read-writecurrent
f3L3FlowPointInnerVlanEthertype
OBJECT-TYPE
.
1.3.6.1.4.1.2544.1.12.37.1.3.1.34Integer32 (0..65535)read-writecurrent
f3L3FlowPointIpVersion
OBJECT-TYPE
.
1.3.6.1.4.1.2544.1.12.37.1.3.1.35IpVersionread-createcurrent
f3L3AclRuleTable
OBJECT-TYPE
A list of entries for the L3 ACL rule.
1.3.6.1.4.1.2544.1.12.37.1.4not-accessiblecurrent
f3L3AclRuleEntry
OBJECT-TYPE
A conceptual row in the f3L3AclRuleTable.
1.3.6.1.4.1.2544.1.12.37.1.4.1not-accessiblecurrent
f3L3AclRuleParentIndex
OBJECT-TYPE
The ACL rule parent number, it could be flow index or L3 flow point index.
1.3.6.1.4.1.2544.1.12.37.1.4.1.1Integer32not-accessiblecurrent
f3L3AclRuleIndex
OBJECT-TYPE
The ACL rule number.
1.3.6.1.4.1.2544.1.12.37.1.4.1.2Integer32not-accessiblecurrent
f3L3AclRuleAlias
OBJECT-TYPE
The ACL rule alias.
1.3.6.1.4.1.2544.1.12.37.1.4.1.3F3DisplayString (SIZE(0..256))read-writecurrent
f3L3AclRuleSrcIpv4AddressControl
OBJECT-TYPE
The ACL rule source IPv4 Adress control whether enabled.
1.3.6.1.4.1.2544.1.12.37.1.4.1.4TruthValueread-writecurrent
f3L3AclRuleDynamicSrcIpControl
OBJECT-TYPE
The ACL rule dynamic source IPv4 or IPv6 Adress control whether enabled.
1.3.6.1.4.1.2544.1.12.37.1.4.1.5TruthValueread-writecurrent
f3L3AclRuleSrcIpv4AddressLowLimit
OBJECT-TYPE
The ACL rule source IPv4 Adress low limit.
1.3.6.1.4.1.2544.1.12.37.1.4.1.6IpAddressread-writecurrent
f3L3AclRuleDstIpv4AddressControl
OBJECT-TYPE
The ACL rule Destination IPv4 Adress control whether enabled.
1.3.6.1.4.1.2544.1.12.37.1.4.1.7TruthValueread-writecurrent
f3L3AclRuleDstIpv4AddressLowLimit
OBJECT-TYPE
The ACL rule Destination IPv4 Adress low limit.
1.3.6.1.4.1.2544.1.12.37.1.4.1.8IpAddressread-writecurrent
f3L3AclRuleIpv4PriorityControl
OBJECT-TYPE
The ACL rule IPv4 Priority control whether enabled.
1.3.6.1.4.1.2544.1.12.37.1.4.1.9TruthValueread-writedeprecated
f3L3AclRuleIpv4PriorityLowLimit
OBJECT-TYPE
The ACL rule IPv4 priority low limit.
1.3.6.1.4.1.2544.1.12.37.1.4.1.10Integer32read-writedeprecated
f3L3AclRuleProtocolControl
OBJECT-TYPE
The ACL rule protocol control whether enabled.
1.3.6.1.4.1.2544.1.12.37.1.4.1.11TruthValueread-writecurrent
f3L3AclRuleProtocolNumber
OBJECT-TYPE
The ACL rule protocol number.
1.3.6.1.4.1.2544.1.12.37.1.4.1.12Integer32read-writecurrent
f3L3AclRuleSrcPortControl
OBJECT-TYPE
The ACL rule source port whether enabled.
1.3.6.1.4.1.2544.1.12.37.1.4.1.13TruthValueread-writecurrent
f3L3AclRuleSrcPortLowLimit
OBJECT-TYPE
The ACL rule source port low limit.
1.3.6.1.4.1.2544.1.12.37.1.4.1.14Integer32read-writecurrent
f3L3AclRuleSrcPortHighLimit
OBJECT-TYPE
The ACL rule source port low limit.
1.3.6.1.4.1.2544.1.12.37.1.4.1.15Integer32read-writecurrent
f3L3AclRuleDstPortControl
OBJECT-TYPE
The ACL rule destination port whether enabled.
1.3.6.1.4.1.2544.1.12.37.1.4.1.16TruthValueread-writecurrent
f3L3AclRuleDstPortLowLimit
OBJECT-TYPE
The ACL rule destination port low limit.
1.3.6.1.4.1.2544.1.12.37.1.4.1.17Integer32read-writecurrent
f3L3AclRuleDstPortHighLimit
OBJECT-TYPE
The ACL rule destination port low limit.
1.3.6.1.4.1.2544.1.12.37.1.4.1.18Integer32read-writecurrent
f3L3AclRulePriority
OBJECT-TYPE
The ACL rule priority.
1.3.6.1.4.1.2544.1.12.37.1.4.1.19Integer32read-writecurrent
f3L3AclRuleCOS
OBJECT-TYPE
The ACL rule class of service.
1.3.6.1.4.1.2544.1.12.37.1.4.1.20Integer32read-writecurrent
f3L3AclRuleOperation
OBJECT-TYPE
The ACL rule action.
1.3.6.1.4.1.2544.1.12.37.1.4.1.21L3AclRuleOperationread-writecurrent
f3L3AclRuleSummary
OBJECT-TYPE
The ACL rule summary.
1.3.6.1.4.1.2544.1.12.37.1.4.1.22F3DisplayStringread-onlycurrent
f3L3AclRuleCosOverrideControl
OBJECT-TYPE
The ACL rule COS Override control.
1.3.6.1.4.1.2544.1.12.37.1.4.1.23TruthValueread-writecurrent
f3L3AclRuleSrcMacAddressControl
OBJECT-TYPE
The ACL rule Source MAC address control.
1.3.6.1.4.1.2544.1.12.37.1.4.1.24TruthValueread-writecurrent
f3L3AclRuleDynamicSrcMacAddressControl
OBJECT-TYPE
The ACL rule dynamic Source MAC address control.
1.3.6.1.4.1.2544.1.12.37.1.4.1.25TruthValueread-writecurrent
f3L3AclRuleSrcMacAddress
OBJECT-TYPE
The ACL rule dynamic Source MAC address.
1.3.6.1.4.1.2544.1.12.37.1.4.1.26MacAddressread-writecurrent
f3L3AclRuleSrcMacAddressMask
OBJECT-TYPE
The ACL rule dynamic Source MAC address mask.
1.3.6.1.4.1.2544.1.12.37.1.4.1.27MacAddressread-writecurrent
f3L3AclRuleDstMacAddressControl
OBJECT-TYPE
The ACL rule dynamic Destination MAC address control.
1.3.6.1.4.1.2544.1.12.37.1.4.1.28TruthValueread-writecurrent
f3L3AclRuleDstMacAddress
OBJECT-TYPE
The ACL rule dynamic Destination MAC address.
1.3.6.1.4.1.2544.1.12.37.1.4.1.29MacAddressread-writecurrent
f3L3AclRuleDstMacAddressMask
OBJECT-TYPE
The ACL rule dynamic Destination MAC address mask.
1.3.6.1.4.1.2544.1.12.37.1.4.1.30MacAddressread-writecurrent
f3L3AclRuleOuterVlanVIDControl
OBJECT-TYPE
The ACL rule outer VID control.
1.3.6.1.4.1.2544.1.12.37.1.4.1.31TruthValueread-writecurrent
f3L3AclRuleOuterVlanVIDLowLimit
OBJECT-TYPE
The ACL rule outer Vlan ID low limit.
1.3.6.1.4.1.2544.1.12.37.1.4.1.32VlanIdread-writecurrent
f3L3AclRuleOuterVlanVIDHighLimit
OBJECT-TYPE
The ACL rule outer Vlan ID high limit.
1.3.6.1.4.1.2544.1.12.37.1.4.1.33VlanIdread-writecurrent
f3L3AclRuleInnerVlanVIDControl
OBJECT-TYPE
The ACL rule inner VID control.
1.3.6.1.4.1.2544.1.12.37.1.4.1.34TruthValueread-writecurrent
f3L3AclRuleInnerVlanVIDLowLimit
OBJECT-TYPE
The ACL rule inner Vlan ID low limit.
1.3.6.1.4.1.2544.1.12.37.1.4.1.35VlanIdread-writecurrent
f3L3AclRuleInnerVlanVIDHighLimit
OBJECT-TYPE
The ACL rule Inner Vlan ID high limit.
1.3.6.1.4.1.2544.1.12.37.1.4.1.36VlanIdread-writecurrent
f3L3AclRuleOuterVlanPcpControl
OBJECT-TYPE
The ACL rule outer vlan PCP control.
1.3.6.1.4.1.2544.1.12.37.1.4.1.37TruthValueread-writecurrent
f3L3AclRuleOuterVlanPcpLowLimit
OBJECT-TYPE
The ACL rule outer vlan PCP priority low limit.
1.3.6.1.4.1.2544.1.12.37.1.4.1.38VlanPriorityread-writecurrent
f3L3AclRuleOuterVlanPcpHighLimit
OBJECT-TYPE
The ACL rule outer vlan PCP priority high limit.
1.3.6.1.4.1.2544.1.12.37.1.4.1.39VlanPriorityread-writecurrent
f3L3AclRuleInnerVlanPcpControl
OBJECT-TYPE
The ACL rule inner vlan PCP control.
1.3.6.1.4.1.2544.1.12.37.1.4.1.40TruthValueread-writecurrent
f3L3AclRuleInnerVlanPcpLowLimit
OBJECT-TYPE
The ACL rule inner vlan PCP priority low limit.
1.3.6.1.4.1.2544.1.12.37.1.4.1.41VlanPriorityread-writecurrent
f3L3AclRuleInnerVlanPcpHighLimit
OBJECT-TYPE
The ACL rule inner vlan PCP priority high limit.
1.3.6.1.4.1.2544.1.12.37.1.4.1.42VlanPriorityread-writecurrent
f3L3AclRuleOuterVlanDeiControl
OBJECT-TYPE
The ACL rule outer vlan DEI control.
1.3.6.1.4.1.2544.1.12.37.1.4.1.43TruthValueread-writecurrent
f3L3AclRuleOuterVlanDei
OBJECT-TYPE
The ACL rule outer vlan DEI.
1.3.6.1.4.1.2544.1.12.37.1.4.1.44Unsigned32 (0..1)read-writecurrent
f3L3AclRuleEtherTypeControl
OBJECT-TYPE
The ACL rule outer vlan ether type control.
1.3.6.1.4.1.2544.1.12.37.1.4.1.45TruthValueread-writecurrent
f3L3AclRuleEtherType
OBJECT-TYPE
The ACL rule outer vlan ether type.
1.3.6.1.4.1.2544.1.12.37.1.4.1.46Integer32read-writecurrent
f3L3AclRuleTcpFlagsControl
OBJECT-TYPE
The ACL rule outer vlan TCP flags control.
1.3.6.1.4.1.2544.1.12.37.1.4.1.47TruthValueread-writecurrent
f3L3AclRuleTcpFlags
OBJECT-TYPE
The ACL rule outer vlan TCP flags.
1.3.6.1.4.1.2544.1.12.37.1.4.1.48Integer32read-writecurrent
f3L3AclRuleSrcIpv4AddressHighLimit
OBJECT-TYPE
The ACL rule source ipv4 adress high limit.
1.3.6.1.4.1.2544.1.12.37.1.4.1.49IpAddressread-writecurrent
f3L3AclRuleDstIpv4AddressHighLimit
OBJECT-TYPE
The ACL rule destination ipv4 adress high limit.
1.3.6.1.4.1.2544.1.12.37.1.4.1.50IpAddressread-writecurrent
f3L3AclRuleIpv4PriorityHighLimit
OBJECT-TYPE
The ACL rule ipv4 priority high limit.
1.3.6.1.4.1.2544.1.12.37.1.4.1.51Integer32read-writedeprecated
f3L3AclRuleStorageType
OBJECT-TYPE
The type of storage configured for this entry.
1.3.6.1.4.1.2544.1.12.37.1.4.1.52StorageTyperead-createcurrent
f3L3AclRuleRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3L3AclRuleRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3L3AclRuleRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3L3AclRuleRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.37.1.4.1.53RowStatusread-createcurrent
f3L3AclRuleAdminState
OBJECT-TYPE
This object allows user configure the Acl Rule in in-service or management state.
1.3.6.1.4.1.2544.1.12.37.1.4.1.54AdminStateread-writecurrent
f3L3AclRuleActive
OBJECT-TYPE
The ACL Rule Active activates/deactivates ACL Rule.
1.3.6.1.4.1.2544.1.12.37.1.4.1.55TruthValueread-writecurrent
f3L3AclRuleSrcIpV6AddressControl
OBJECT-TYPE
The ACL rule source ipv6 adress control.
1.3.6.1.4.1.2544.1.12.37.1.4.1.56TruthValueread-writecurrent
f3L3AclRuleSrcIpV6Address
OBJECT-TYPE
The ACL rule source ipv6 adress.
1.3.6.1.4.1.2544.1.12.37.1.4.1.57Ipv6Addressread-writecurrent
f3L3AclRuleSrcIpV6AddressPrefixLen
OBJECT-TYPE
The ACL rule source ipv6 adress prefix length.
1.3.6.1.4.1.2544.1.12.37.1.4.1.58Integer32 (0..128)read-writecurrent
f3L3AclRuleDstIpV6AddressControl
OBJECT-TYPE
The ACL rule destination ipv6 adress control.
1.3.6.1.4.1.2544.1.12.37.1.4.1.59TruthValueread-writecurrent
f3L3AclRuleDstIpV6Address
OBJECT-TYPE
The ACL rule destination ipv6 adress.
1.3.6.1.4.1.2544.1.12.37.1.4.1.60Ipv6Addressread-writecurrent
f3L3AclRuleDstIpV6AddressPrefixLen
OBJECT-TYPE
The ACL rule destination ipv6 adress prefix length.
1.3.6.1.4.1.2544.1.12.37.1.4.1.61Integer32 (0..128)read-writecurrent
f3L3AclRuleIpV6FlowLabelControl
OBJECT-TYPE
The ACL rule ipv6 Flow Label Control enables/disables Flow Label.
1.3.6.1.4.1.2544.1.12.37.1.4.1.62TruthValueread-writecurrent
f3L3AclRuleIpV6FlowLabel
OBJECT-TYPE
The ACL rule ipv6 Flow Label.
1.3.6.1.4.1.2544.1.12.37.1.4.1.63Integer32 (0..1048575)read-writecurrent
f3L3AclRulePriorityControl
OBJECT-TYPE
The ACL rule Priority control whether enabled.
1.3.6.1.4.1.2544.1.12.37.1.4.1.64TruthValueread-writecurrent
f3L3AclRulePriorityLowLimit
OBJECT-TYPE
The ACL rule priority low limit.
1.3.6.1.4.1.2544.1.12.37.1.4.1.65Integer32read-writecurrent
f3L3AclRulePriorityHighLimit
OBJECT-TYPE
The ACL rule priority high limit.
1.3.6.1.4.1.2544.1.12.37.1.4.1.66Integer32read-writecurrent
f3L2A2NAclRuleTable
OBJECT-TYPE
A list of entries for the L2A2N ACL rule.
1.3.6.1.4.1.2544.1.12.37.1.5not-accessiblecurrent
f3L2A2NAclRuleEntry
OBJECT-TYPE
A conceptual row in the f3L2A2NAclRuleTable.
1.3.6.1.4.1.2544.1.12.37.1.5.1not-accessiblecurrent
f3L2A2NAclRuleParentIndex
OBJECT-TYPE
The ACL rule parent number, it could be flow index
1.3.6.1.4.1.2544.1.12.37.1.5.1.1Integer32not-accessiblecurrent
f3L2A2NAclRuleIndex
OBJECT-TYPE
The ACL rule number.
1.3.6.1.4.1.2544.1.12.37.1.5.1.2Integer32not-accessiblecurrent
f3L2A2NAclRuleAlias
OBJECT-TYPE
The ACL rule alias.
1.3.6.1.4.1.2544.1.12.37.1.5.1.3F3DisplayString (SIZE(0..256))read-writecurrent
f3L2A2NAclRuleSrcIpv4AddressControl
OBJECT-TYPE
The ACL rule source IPv4 Adress control whether enabled.
1.3.6.1.4.1.2544.1.12.37.1.5.1.4TruthValueread-writecurrent
f3L2A2NAclRuleDynamicSrcIpControl
OBJECT-TYPE
The ACL rule dynamic source IPv4 or IPv6 Adress control whether enabled.
1.3.6.1.4.1.2544.1.12.37.1.5.1.5TruthValueread-writecurrent
f3L2A2NAclRuleSrcIpv4AddressLowLimit
OBJECT-TYPE
The ACL rule source IPv4 Adress low limit.
1.3.6.1.4.1.2544.1.12.37.1.5.1.6IpAddressread-writecurrent
f3L2A2NAclRuleDstIpv4AddressControl
OBJECT-TYPE
The ACL rule Destination IPv4 Adress control whether enabled.
1.3.6.1.4.1.2544.1.12.37.1.5.1.7TruthValueread-writecurrent
f3L2A2NAclRuleDstIpv4AddressLowLimit
OBJECT-TYPE
The ACL rule Destination IPv4 Adress low limit.
1.3.6.1.4.1.2544.1.12.37.1.5.1.8IpAddressread-writecurrent
f3L2A2NAclRuleIpv4PriorityControl
OBJECT-TYPE
The ACL rule IPv4 Priority control whether enabled.
1.3.6.1.4.1.2544.1.12.37.1.5.1.9TruthValueread-writecurrent
f3L2A2NAclRuleIpv4PriorityLowLimit
OBJECT-TYPE
The ACL rule IPv4 priority low limit.
1.3.6.1.4.1.2544.1.12.37.1.5.1.10Integer32read-writecurrent
f3L2A2NAclRuleProtocolControl
OBJECT-TYPE
The ACL rule protocol control whether enabled.
1.3.6.1.4.1.2544.1.12.37.1.5.1.11TruthValueread-writecurrent
f3L2A2NAclRuleProtocolNumber
OBJECT-TYPE
The ACL rule protocol number.
1.3.6.1.4.1.2544.1.12.37.1.5.1.12Integer32read-writecurrent
f3L2A2NAclRuleSrcPortControl
OBJECT-TYPE
The ACL rule source port whether enabled.
1.3.6.1.4.1.2544.1.12.37.1.5.1.13TruthValueread-writecurrent
f3L2A2NAclRuleSrcPortLowLimit
OBJECT-TYPE
The ACL rule source port low limit.
1.3.6.1.4.1.2544.1.12.37.1.5.1.14Integer32read-writecurrent
f3L2A2NAclRuleSrcPortHighLimit
OBJECT-TYPE
The ACL rule source port low limit.
1.3.6.1.4.1.2544.1.12.37.1.5.1.15Integer32read-writecurrent
f3L2A2NAclRuleDstPortControl
OBJECT-TYPE
The ACL rule destination port whether enabled.
1.3.6.1.4.1.2544.1.12.37.1.5.1.16TruthValueread-writecurrent
f3L2A2NAclRuleDstPortLowLimit
OBJECT-TYPE
The ACL rule destination port low limit.
1.3.6.1.4.1.2544.1.12.37.1.5.1.17Integer32read-writecurrent
f3L2A2NAclRuleDstPortHighLimit
OBJECT-TYPE
The ACL rule destination port low limit.
1.3.6.1.4.1.2544.1.12.37.1.5.1.18Integer32read-writecurrent
f3L2A2NAclRulePriority
OBJECT-TYPE
The ACL rule priority.
1.3.6.1.4.1.2544.1.12.37.1.5.1.19Integer32read-writecurrent
f3L2A2NAclRuleCOS
OBJECT-TYPE
The ACL rule class of service.
1.3.6.1.4.1.2544.1.12.37.1.5.1.20Integer32read-writecurrent
f3L2A2NAclRuleOperation
OBJECT-TYPE
The ACL rule action.
1.3.6.1.4.1.2544.1.12.37.1.5.1.21L3AclRuleOperationread-writecurrent
f3L2A2NAclRuleSummary
OBJECT-TYPE
The ACL rule summary.
1.3.6.1.4.1.2544.1.12.37.1.5.1.22F3DisplayStringread-onlycurrent
f3L2A2NAclRuleCosOverrideControl
OBJECT-TYPE
The ACL rule COS Override control.
1.3.6.1.4.1.2544.1.12.37.1.5.1.23TruthValueread-writecurrent
f3L2A2NAclRuleSrcMacAddressControl
OBJECT-TYPE
The ACL rule Source MAC address control.
1.3.6.1.4.1.2544.1.12.37.1.5.1.24TruthValueread-writecurrent
f3L2A2NAclRuleDynamicSrcMacAddressControl
OBJECT-TYPE
The ACL rule dynamic Source MAC address control.
1.3.6.1.4.1.2544.1.12.37.1.5.1.25TruthValueread-writecurrent
f3L2A2NAclRuleSrcMacAddress
OBJECT-TYPE
The ACL rule dynamic Source MAC address.
1.3.6.1.4.1.2544.1.12.37.1.5.1.26MacAddressread-writecurrent
f3L2A2NAclRuleSrcMacAddressMask
OBJECT-TYPE
The ACL rule dynamic Source MAC address mask.
1.3.6.1.4.1.2544.1.12.37.1.5.1.27MacAddressread-writecurrent
f3L2A2NAclRuleDstMacAddressControl
OBJECT-TYPE
The ACL rule dynamic Destination MAC address control.
1.3.6.1.4.1.2544.1.12.37.1.5.1.28TruthValueread-writecurrent
f3L2A2NAclRuleDstMacAddress
OBJECT-TYPE
The ACL rule dynamic Destination MAC address.
1.3.6.1.4.1.2544.1.12.37.1.5.1.29MacAddressread-writecurrent
f3L2A2NAclRuleDstMacAddressMask
OBJECT-TYPE
The ACL rule dynamic Destination MAC address mask.
1.3.6.1.4.1.2544.1.12.37.1.5.1.30MacAddressread-writecurrent
f3L2A2NAclRuleOuterVlanVIDControl
OBJECT-TYPE
The ACL rule outer VID control.
1.3.6.1.4.1.2544.1.12.37.1.5.1.31TruthValueread-writecurrent
f3L2A2NAclRuleOuterVlanVIDLowLimit
OBJECT-TYPE
The ACL rule outer Vlan ID low limit.
1.3.6.1.4.1.2544.1.12.37.1.5.1.32VlanIdread-writecurrent
f3L2A2NAclRuleOuterVlanVIDHighLimit
OBJECT-TYPE
The ACL rule outer Vlan ID high limit.
1.3.6.1.4.1.2544.1.12.37.1.5.1.33VlanIdread-writecurrent
f3L2A2NAclRuleInnerVlanVIDControl
OBJECT-TYPE
The ACL rule inner VID control.
1.3.6.1.4.1.2544.1.12.37.1.5.1.34TruthValueread-writecurrent
f3L2A2NAclRuleInnerVlanVIDLowLimit
OBJECT-TYPE
The ACL rule inner Vlan ID low limit.
1.3.6.1.4.1.2544.1.12.37.1.5.1.35VlanIdread-writecurrent
f3L2A2NAclRuleInnerVlanVIDHighLimit
OBJECT-TYPE
The ACL rule Inner Vlan ID high limit.
1.3.6.1.4.1.2544.1.12.37.1.5.1.36VlanIdread-writecurrent
f3L2A2NAclRuleOuterVlanPcpControl
OBJECT-TYPE
The ACL rule outer vlan PCP control.
1.3.6.1.4.1.2544.1.12.37.1.5.1.37TruthValueread-writecurrent
f3L2A2NAclRuleOuterVlanPcpLowLimit
OBJECT-TYPE
The ACL rule outer vlan PCP priority low limit.
1.3.6.1.4.1.2544.1.12.37.1.5.1.38VlanPriorityread-writecurrent
f3L2A2NAclRuleOuterVlanPcpHighLimit
OBJECT-TYPE
The ACL rule outer vlan PCP priority high limit.
1.3.6.1.4.1.2544.1.12.37.1.5.1.39VlanPriorityread-writecurrent
f3L2A2NAclRuleInnerVlanPcpControl
OBJECT-TYPE
The ACL rule inner vlan PCP control.
1.3.6.1.4.1.2544.1.12.37.1.5.1.40TruthValueread-writecurrent
f3L2A2NAclRuleInnerVlanPcpLowLimit
OBJECT-TYPE
The ACL rule inner vlan PCP priority low limit.
1.3.6.1.4.1.2544.1.12.37.1.5.1.41VlanPriorityread-writecurrent
f3L2A2NAclRuleInnerVlanPcpHighLimit
OBJECT-TYPE
The ACL rule inner vlan PCP priority high limit.
1.3.6.1.4.1.2544.1.12.37.1.5.1.42VlanPriorityread-writecurrent
f3L2A2NAclRuleOuterVlanDeiControl
OBJECT-TYPE
The ACL rule outer vlan DEI control.
1.3.6.1.4.1.2544.1.12.37.1.5.1.43TruthValueread-writecurrent
f3L2A2NAclRuleOuterVlanDei
OBJECT-TYPE
The ACL rule outer vlan DEI.
1.3.6.1.4.1.2544.1.12.37.1.5.1.44Unsigned32 (0..1)read-writecurrent
f3L2A2NAclRuleEtherTypeControl
OBJECT-TYPE
The ACL rule outer vlan ether type control.
1.3.6.1.4.1.2544.1.12.37.1.5.1.45TruthValueread-writecurrent
f3L2A2NAclRuleEtherType
OBJECT-TYPE
The ACL rule outer vlan ether type.
1.3.6.1.4.1.2544.1.12.37.1.5.1.46Integer32read-writecurrent
f3L2A2NAclRuleTcpFlagsControl
OBJECT-TYPE
The ACL rule outer vlan TCP flags control.
1.3.6.1.4.1.2544.1.12.37.1.5.1.47TruthValueread-writecurrent
f3L2A2NAclRuleTcpFlags
OBJECT-TYPE
The ACL rule outer vlan TCP flags.
1.3.6.1.4.1.2544.1.12.37.1.5.1.48Integer32read-writecurrent
f3L2A2NAclRuleSrcIpv4AddressHighLimit
OBJECT-TYPE
The ACL rule source ipv4 adress high limit.
1.3.6.1.4.1.2544.1.12.37.1.5.1.49IpAddressread-writecurrent
f3L2A2NAclRuleDstIpv4AddressHighLimit
OBJECT-TYPE
The ACL rule destination ipv4 adress high limit.
1.3.6.1.4.1.2544.1.12.37.1.5.1.50IpAddressread-writecurrent
f3L2A2NAclRuleIpv4PriorityHighLimit
OBJECT-TYPE
The ACL rule ipv4 priority high limit.
1.3.6.1.4.1.2544.1.12.37.1.5.1.51Integer32read-writecurrent
f3L2A2NAclRuleStorageType
OBJECT-TYPE
The type of storage configured for this entry.
1.3.6.1.4.1.2544.1.12.37.1.5.1.52StorageTyperead-createcurrent
f3L2A2NAclRuleRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3L2A2NAclRuleRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3L2A2NAclRuleRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3L2A2NAclRuleRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.37.1.5.1.53RowStatusread-createcurrent
f3L2A2NAclRuleAdminState
OBJECT-TYPE
This object allows user configure the Acl Rule in-service or management state.
1.3.6.1.4.1.2544.1.12.37.1.5.1.54AdminStateread-writecurrent
f3L2A2NAclRuleActive
OBJECT-TYPE
The ACL rule active control.
1.3.6.1.4.1.2544.1.12.37.1.5.1.55TruthValueread-writecurrent
f3L2A2NAclRuleSrcIpV6AddressControl
OBJECT-TYPE
The ACL rule source ipv6 adress control.
1.3.6.1.4.1.2544.1.12.37.1.5.1.56TruthValueread-writecurrent
f3L2A2NAclRuleSrcIpV6Address
OBJECT-TYPE
The ACL rule source ipv6 adress.
1.3.6.1.4.1.2544.1.12.37.1.5.1.57Ipv6Addressread-writecurrent
f3L2A2NAclRuleSrcIpV6AddressPrefixLen
OBJECT-TYPE
The ACL rule source ipv6 adress prefix length.
1.3.6.1.4.1.2544.1.12.37.1.5.1.58Integer32read-writecurrent
f3L2A2NAclRuleDstIpV6AddressControl
OBJECT-TYPE
The ACL rule destination ipv6 adress control.
1.3.6.1.4.1.2544.1.12.37.1.5.1.59TruthValueread-writecurrent
f3L2A2NAclRuleDstIpV6Address
OBJECT-TYPE
The ACL rule destination ipv6 adress.
1.3.6.1.4.1.2544.1.12.37.1.5.1.60Ipv6Addressread-writecurrent
f3L2A2NAclRuleDstIpV6AddressPrefixLen
OBJECT-TYPE
The ACL rule destination ipv6 adress prefix length.
1.3.6.1.4.1.2544.1.12.37.1.5.1.61Integer32read-writecurrent
f3L2A2NAclRuleIpV6FlowLabelControl
OBJECT-TYPE
The ACL rule IPv6 flow lable control.
1.3.6.1.4.1.2544.1.12.37.1.5.1.62TruthValueread-writecurrent
f3L2A2NAclRuleIpV6FlowLabel
OBJECT-TYPE
The ACL rule IPv6 flow lable.
1.3.6.1.4.1.2544.1.12.37.1.5.1.63Integer32read-writecurrent
f3L2N2AAclRuleTable
OBJECT-TYPE
A list of entries for the L2N2A ACL rule.
1.3.6.1.4.1.2544.1.12.37.1.6not-accessiblecurrent
f3L2N2AAclRuleEntry
OBJECT-TYPE
A conceptual row in the f3L2N2AAclRuleTable.
1.3.6.1.4.1.2544.1.12.37.1.6.1not-accessiblecurrent
f3L2N2AAclRuleParentIndex
OBJECT-TYPE
The ACL rule parent number, it could be flow index
1.3.6.1.4.1.2544.1.12.37.1.6.1.1Integer32not-accessiblecurrent
f3L2N2AAclRuleIndex
OBJECT-TYPE
The ACL rule number.
1.3.6.1.4.1.2544.1.12.37.1.6.1.2Integer32not-accessiblecurrent
f3L2N2AAclRuleAlias
OBJECT-TYPE
The ACL rule alias.
1.3.6.1.4.1.2544.1.12.37.1.6.1.3F3DisplayString (SIZE(0..256))read-writecurrent
f3L2N2AAclRuleSrcIpv4AddressControl
OBJECT-TYPE
The ACL rule source IPv4 Adress control whether enabled.
1.3.6.1.4.1.2544.1.12.37.1.6.1.4TruthValueread-writecurrent
f3L2N2AAclRuleDynamicSrcIpControl
OBJECT-TYPE
The ACL rule dynamic source IPv4 or IPv6 Adress control whether enabled.
1.3.6.1.4.1.2544.1.12.37.1.6.1.5TruthValueread-writecurrent
f3L2N2AAclRuleSrcIpv4AddressLowLimit
OBJECT-TYPE
The ACL rule source IPv4 Adress low limit.
1.3.6.1.4.1.2544.1.12.37.1.6.1.6IpAddressread-writecurrent
f3L2N2AAclRuleDstIpv4AddressControl
OBJECT-TYPE
The ACL rule Destination IPv4 Adress control whether enabled.
1.3.6.1.4.1.2544.1.12.37.1.6.1.7TruthValueread-writecurrent
f3L2N2AAclRuleDstIpv4AddressLowLimit
OBJECT-TYPE
The ACL rule Destination IPv4 Adress low limit.
1.3.6.1.4.1.2544.1.12.37.1.6.1.8IpAddressread-writecurrent
f3L2N2AAclRuleIpv4PriorityControl
OBJECT-TYPE
The ACL rule IPv4 Priority control whether enabled.
1.3.6.1.4.1.2544.1.12.37.1.6.1.9TruthValueread-writecurrent
f3L2N2AAclRuleIpv4PriorityLowLimit
OBJECT-TYPE
The ACL rule IPv4 priority low limit.
1.3.6.1.4.1.2544.1.12.37.1.6.1.10Integer32read-writecurrent
f3L2N2AAclRuleProtocolControl
OBJECT-TYPE
The ACL rule protocol control whether enabled.
1.3.6.1.4.1.2544.1.12.37.1.6.1.11TruthValueread-writecurrent
f3L2N2AAclRuleProtocolNumber
OBJECT-TYPE
The ACL rule protocol number.
1.3.6.1.4.1.2544.1.12.37.1.6.1.12Integer32read-writecurrent
f3L2N2AAclRuleSrcPortControl
OBJECT-TYPE
The ACL rule source port whether enabled.
1.3.6.1.4.1.2544.1.12.37.1.6.1.13TruthValueread-writecurrent
f3L2N2AAclRuleSrcPortLowLimit
OBJECT-TYPE
The ACL rule source port low limit.
1.3.6.1.4.1.2544.1.12.37.1.6.1.14Integer32read-writecurrent
f3L2N2AAclRuleSrcPortHighLimit
OBJECT-TYPE
The ACL rule source port low limit.
1.3.6.1.4.1.2544.1.12.37.1.6.1.15Integer32read-writecurrent
f3L2N2AAclRuleDstPortControl
OBJECT-TYPE
The ACL rule destination port whether enabled.
1.3.6.1.4.1.2544.1.12.37.1.6.1.16TruthValueread-writecurrent
f3L2N2AAclRuleDstPortLowLimit
OBJECT-TYPE
The ACL rule destination port low limit.
1.3.6.1.4.1.2544.1.12.37.1.6.1.17Integer32read-writecurrent
f3L2N2AAclRuleDstPortHighLimit
OBJECT-TYPE
The ACL rule destination port low limit.
1.3.6.1.4.1.2544.1.12.37.1.6.1.18Integer32read-writecurrent
f3L2N2AAclRulePriority
OBJECT-TYPE
The ACL rule priority.
1.3.6.1.4.1.2544.1.12.37.1.6.1.19Integer32read-writecurrent
f3L2N2AAclRuleCOS
OBJECT-TYPE
The ACL rule class of service.
1.3.6.1.4.1.2544.1.12.37.1.6.1.20Integer32read-writecurrent
f3L2N2AAclRuleOperation
OBJECT-TYPE
The ACL rule action.
1.3.6.1.4.1.2544.1.12.37.1.6.1.21L3AclRuleOperationread-writecurrent
f3L2N2AAclRuleSummary
OBJECT-TYPE
The ACL rule summary.
1.3.6.1.4.1.2544.1.12.37.1.6.1.22F3DisplayStringread-onlycurrent
f3L2N2AAclRuleCosOverrideControl
OBJECT-TYPE
The ACL rule COS Override control.
1.3.6.1.4.1.2544.1.12.37.1.6.1.23TruthValueread-writecurrent
f3L2N2AAclRuleSrcMacAddressControl
OBJECT-TYPE
The ACL rule Source MAC address control.
1.3.6.1.4.1.2544.1.12.37.1.6.1.24TruthValueread-writecurrent
f3L2N2AAclRuleDynamicSrcMacAddressControl
OBJECT-TYPE
The ACL rule dynamic Source MAC address control.
1.3.6.1.4.1.2544.1.12.37.1.6.1.25TruthValueread-writecurrent
f3L2N2AAclRuleSrcMacAddress
OBJECT-TYPE
The ACL rule dynamic Source MAC address.
1.3.6.1.4.1.2544.1.12.37.1.6.1.26MacAddressread-writecurrent
f3L2N2AAclRuleSrcMacAddressMask
OBJECT-TYPE
The ACL rule dynamic Source MAC address mask.
1.3.6.1.4.1.2544.1.12.37.1.6.1.27MacAddressread-writecurrent
f3L2N2AAclRuleDstMacAddressControl
OBJECT-TYPE
The ACL rule dynamic Destination MAC address control.
1.3.6.1.4.1.2544.1.12.37.1.6.1.28TruthValueread-writecurrent
f3L2N2AAclRuleDstMacAddress
OBJECT-TYPE
The ACL rule dynamic Destination MAC address.
1.3.6.1.4.1.2544.1.12.37.1.6.1.29MacAddressread-writecurrent
f3L2N2AAclRuleDstMacAddressMask
OBJECT-TYPE
The ACL rule dynamic Destination MAC address mask.
1.3.6.1.4.1.2544.1.12.37.1.6.1.30MacAddressread-writecurrent
f3L2N2AAclRuleOuterVlanVIDControl
OBJECT-TYPE
The ACL rule outer VID control.
1.3.6.1.4.1.2544.1.12.37.1.6.1.31TruthValueread-writecurrent
f3L2N2AAclRuleOuterVlanVIDLowLimit
OBJECT-TYPE
The ACL rule outer Vlan ID low limit.
1.3.6.1.4.1.2544.1.12.37.1.6.1.32VlanIdread-writecurrent
f3L2N2AAclRuleOuterVlanVIDHighLimit
OBJECT-TYPE
The ACL rule outer Vlan ID high limit.
1.3.6.1.4.1.2544.1.12.37.1.6.1.33VlanIdread-writecurrent
f3L2N2AAclRuleInnerVlanVIDControl
OBJECT-TYPE
The ACL rule inner VID control.
1.3.6.1.4.1.2544.1.12.37.1.6.1.34TruthValueread-writecurrent
f3L2N2AAclRuleInnerVlanVIDLowLimit
OBJECT-TYPE
The ACL rule inner Vlan ID low limit.
1.3.6.1.4.1.2544.1.12.37.1.6.1.35VlanIdread-writecurrent
f3L2N2AAclRuleInnerVlanVIDHighLimit
OBJECT-TYPE
The ACL rule Inner Vlan ID high limit.
1.3.6.1.4.1.2544.1.12.37.1.6.1.36VlanIdread-writecurrent
f3L2N2AAclRuleOuterVlanPcpControl
OBJECT-TYPE
The ACL rule outer vlan PCP control.
1.3.6.1.4.1.2544.1.12.37.1.6.1.37TruthValueread-writecurrent
f3L2N2AAclRuleOuterVlanPcpLowLimit
OBJECT-TYPE
The ACL rule outer vlan PCP priority low limit.
1.3.6.1.4.1.2544.1.12.37.1.6.1.38VlanPriorityread-writecurrent
f3L2N2AAclRuleOuterVlanPcpHighLimit
OBJECT-TYPE
The ACL rule outer vlan PCP priority high limit.
1.3.6.1.4.1.2544.1.12.37.1.6.1.39VlanPriorityread-writecurrent
f3L2N2AAclRuleInnerVlanPcpControl
OBJECT-TYPE
The ACL rule inner vlan PCP control.
1.3.6.1.4.1.2544.1.12.37.1.6.1.40TruthValueread-writecurrent
f3L2N2AAclRuleInnerVlanPcpLowLimit
OBJECT-TYPE
The ACL rule inner vlan PCP priority low limit.
1.3.6.1.4.1.2544.1.12.37.1.6.1.41VlanPriorityread-writecurrent
f3L2N2AAclRuleInnerVlanPcpHighLimit
OBJECT-TYPE
The ACL rule inner vlan PCP priority high limit.
1.3.6.1.4.1.2544.1.12.37.1.6.1.42VlanPriorityread-writecurrent
f3L2N2AAclRuleOuterVlanDeiControl
OBJECT-TYPE
The ACL rule outer vlan DEI control.
1.3.6.1.4.1.2544.1.12.37.1.6.1.43TruthValueread-writecurrent
f3L2N2AAclRuleOuterVlanDei
OBJECT-TYPE
The ACL rule outer vlan DEI.
1.3.6.1.4.1.2544.1.12.37.1.6.1.44Unsigned32 (0..1)read-writecurrent
f3L2N2AAclRuleEtherTypeControl
OBJECT-TYPE
The ACL rule outer vlan ether type control.
1.3.6.1.4.1.2544.1.12.37.1.6.1.45TruthValueread-writecurrent
f3L2N2AAclRuleEtherType
OBJECT-TYPE
The ACL rule outer vlan ether type.
1.3.6.1.4.1.2544.1.12.37.1.6.1.46Integer32read-writecurrent
f3L2N2AAclRuleTcpFlagsControl
OBJECT-TYPE
The ACL rule outer vlan TCP flags control.
1.3.6.1.4.1.2544.1.12.37.1.6.1.47TruthValueread-writecurrent
f3L2N2AAclRuleTcpFlags
OBJECT-TYPE
The ACL rule outer vlan TCP flags.
1.3.6.1.4.1.2544.1.12.37.1.6.1.48Integer32read-writecurrent
f3L2N2AAclRuleSrcIpv4AddressHighLimit
OBJECT-TYPE
The ACL rule source ipv4 adress high limit.
1.3.6.1.4.1.2544.1.12.37.1.6.1.49IpAddressread-writecurrent
f3L2N2AAclRuleDstIpv4AddressHighLimit
OBJECT-TYPE
The ACL rule destination ipv4 adress high limit.
1.3.6.1.4.1.2544.1.12.37.1.6.1.50IpAddressread-writecurrent
f3L2N2AAclRuleIpv4PriorityHighLimit
OBJECT-TYPE
The ACL rule ipv4 priority high limit.
1.3.6.1.4.1.2544.1.12.37.1.6.1.51Integer32read-writecurrent
f3L2N2AAclRuleStorageType
OBJECT-TYPE
The type of storage configured for this entry.
1.3.6.1.4.1.2544.1.12.37.1.6.1.52StorageTyperead-createcurrent
f3L2N2AAclRuleRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3L2N2AAclRuleRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3L2N2AAclRuleRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3L2N2AAclRuleRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.37.1.6.1.53RowStatusread-createcurrent
f3L2N2AAclRuleAdminState
OBJECT-TYPE
This object allows user configure the Acl Rule in-service or management state.
1.3.6.1.4.1.2544.1.12.37.1.6.1.54AdminStateread-writecurrent
f3L2N2AAclRuleActive
OBJECT-TYPE
The ACL rule active control.
1.3.6.1.4.1.2544.1.12.37.1.6.1.55TruthValueread-writecurrent
f3L2N2AAclRuleSrcIpV6AddressControl
OBJECT-TYPE
The ACL rule source ipv6 adress control.
1.3.6.1.4.1.2544.1.12.37.1.6.1.56TruthValueread-writecurrent
f3L2N2AAclRuleSrcIpV6Address
OBJECT-TYPE
The ACL rule source ipv6 adress.
1.3.6.1.4.1.2544.1.12.37.1.6.1.57Ipv6Addressread-writecurrent
f3L2N2AAclRuleSrcIpV6AddressPrefixLen
OBJECT-TYPE
The ACL rule source ipv6 adress prefix length.
1.3.6.1.4.1.2544.1.12.37.1.6.1.58Integer32read-writecurrent
f3L2N2AAclRuleDstIpV6AddressControl
OBJECT-TYPE
The ACL rule destination ipv6 adress control.
1.3.6.1.4.1.2544.1.12.37.1.6.1.59TruthValueread-writecurrent
f3L2N2AAclRuleDstIpV6Address
OBJECT-TYPE
The ACL rule destination ipv6 adress.
1.3.6.1.4.1.2544.1.12.37.1.6.1.60Ipv6Addressread-writecurrent
f3L2N2AAclRuleDstIpV6AddressPrefixLen
OBJECT-TYPE
The ACL rule destination ipv6 adress prefix length.
1.3.6.1.4.1.2544.1.12.37.1.6.1.61Integer32read-writecurrent
f3L2N2AAclRuleIpV6FlowLabelControl
OBJECT-TYPE
The ACL rule IPv6 flow lable control.
1.3.6.1.4.1.2544.1.12.37.1.6.1.62TruthValueread-writecurrent
f3L2N2AAclRuleIpV6FlowLabel
OBJECT-TYPE
The ACL rule IPv6 flow lable.
1.3.6.1.4.1.2544.1.12.37.1.6.1.63Integer32read-writecurrent
f3L3QosPolicerTable
OBJECT-TYPE
A list of entries corresponding to Ethernet Quality of Service Policer for configuration purposes.
1.3.6.1.4.1.2544.1.12.37.1.7not-accessiblecurrent
f3L3QosPolicerEntry
OBJECT-TYPE
A conceptual row in the f3L3QosPolicerTable. These entries represent a Quality of Service Policer.
1.3.6.1.4.1.2544.1.12.37.1.7.1not-accessiblecurrent
f3L3QosPolicerIndex
OBJECT-TYPE
The Policer Index that represents the COS level. This is applicable in case of a Multi COS flow. Index 1 represents COS 0; Index 2 represents COS 1 and so on. In release 5.6CC the range is extended to 1..16 to support duplicate N2A policers on a Flow. The duplicate policers are created under a Flow if network interface of the Flow is ERP Group or Split Horizon Group. In case of multi-cos Flow indices 1..8 represent policers of COS 0..7 going from Network 1 port; indices 9..16 represent policers for COS 0..7 going from Network 2 port. In case of single-cos Flow index 1 represents policer going from Network 1 port; index 9 represents policer going from Network 2 port.
1.3.6.1.4.1.2544.1.12.37.1.7.1.1Integer32 (1..16)read-createcurrent
f3L3QosPolicerAdminState
OBJECT-TYPE
This object represents the Administrative State of the QOS Flow Policer.
1.3.6.1.4.1.2544.1.12.37.1.7.1.2AdminStateread-writecurrent
f3L3QosPolicerOperationalState
OBJECT-TYPE
This object represents the Operational State of the QOS Flow Policer.
1.3.6.1.4.1.2544.1.12.37.1.7.1.3OperationalStateread-onlycurrent
f3L3QosPolicerSecondaryState
OBJECT-TYPE
This object represents the Secondary State of the QOS Flow Policer.
1.3.6.1.4.1.2544.1.12.37.1.7.1.4SecondaryStateread-onlycurrent
f3L3QosPolicerCIRLo
OBJECT-TYPE
This object allows specification of the Commited Information Rate(CIR) on Policer. This represents the lower 32 bits of the CIR.
1.3.6.1.4.1.2544.1.12.37.1.7.1.5Unsigned32read-createcurrent
f3L3QosPolicerCIRHi
OBJECT-TYPE
This object allows specification of the Commited Information Rate(CIR) on Policer. This represents the upper 32 bits of the CIR.
1.3.6.1.4.1.2544.1.12.37.1.7.1.6Unsigned32read-createcurrent
f3L3QosPolicerEIRLo
OBJECT-TYPE
This object allows specification of the Excess Information Rate(EIR) on the Policer. This represents the lower 32 bits of the EIR.
1.3.6.1.4.1.2544.1.12.37.1.7.1.7Unsigned32read-createcurrent
f3L3QosPolicerEIRHi
OBJECT-TYPE
This object allows specification of the Excess Information Rate(EIR) on the Policer. This represents the upper 32 bits of the EIR.
1.3.6.1.4.1.2544.1.12.37.1.7.1.8Unsigned32read-createcurrent
f3L3QosPolicerCBS
OBJECT-TYPE
This object allows specification of the Commited Burst Size (CBS) on Policer.
1.3.6.1.4.1.2544.1.12.37.1.7.1.9Integer32read-createcurrent
f3L3QosPolicerEBS
OBJECT-TYPE
This object allows specification of the Excess Burst Size (EBS) on the Policer.
1.3.6.1.4.1.2544.1.12.37.1.7.1.10Integer32read-createcurrent
f3L3QosPolicerAlgorithm
OBJECT-TYPE
This object allows specification of Policer algorithm as 'srTCM' (Single Rate Triple Color Marking) or 'trTCM' (Two Rate Triple Color Marking).
1.3.6.1.4.1.2544.1.12.37.1.7.1.11PolicerAlgorithmTyperead-onlycurrent
f3L3QosPolicerColorMode
OBJECT-TYPE
This object allows specification of Policer Color Mode as 'color-aware' or 'color-blind'.
1.3.6.1.4.1.2544.1.12.37.1.7.1.12PolicerColorModeread-createcurrent
f3L3QosPolicerCouplingFlag
OBJECT-TYPE
This object allows specification of Policer Coupling Flag. When coupling is enabled, tokens that would normally be added to the C-bucket are passed to the E-bucket only once the CIR bucket has reached its CBS level. Therefore under this condition the E-bucket is being filled at the rate of CIR + EIR. Normally the long term average of frames declared yellow is bounded by the EIR. Coupling is a function to allow the long term average of frames declared yellow to be bounded by CIR + EIR. This allows a higher volume of yellow frames to be delivered/received if the arrival of green marked frames is low. Tokens from the E-bucket do NOT get passed to the C-bucket once the EBS level has been reached. Enabling coupling in combination with a provisioned EIR of 0 allows for a single rate three color marking (srTCM) algorithm to be established. In this situation the E-bucket is filled at the CIR rate in the case the C-bucket is filled to its CBS level.
1.3.6.1.4.1.2544.1.12.37.1.7.1.13TruthValueread-createcurrent
f3L3QosPolicerStorageType
OBJECT-TYPE
The type of storage configured for this entry.
1.3.6.1.4.1.2544.1.12.37.1.7.1.14StorageTyperead-createcurrent
f3L3QosPolicerRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3L3QosPolicerRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3L3QosPolicerRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3L3QosPolicerRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.37.1.7.1.15RowStatusread-createcurrent
f3L3QosPolicerCIRMaxHi
OBJECT-TYPE
This object allows specification of the Commited Information Rate(CIR) MAX on Policer. This represents the high 32 bits.
1.3.6.1.4.1.2544.1.12.37.1.7.1.16Unsigned32read-writecurrent
f3L3QosPolicerCIRMaxLo
OBJECT-TYPE
This object allows specification of the Commited Information Rate(CIR) MAX on Policer. This represents the lower 32 bits.
1.3.6.1.4.1.2544.1.12.37.1.7.1.17Unsigned32read-writecurrent
f3L3QosPolicerEIRMaxHi
OBJECT-TYPE
This object allows specification of the Excess Information Rate(EIR) MAX on the Policer. This represents the high 32 bits.
1.3.6.1.4.1.2544.1.12.37.1.7.1.18Unsigned32read-writecurrent
f3L3QosPolicerEIRMaxLo
OBJECT-TYPE
This object allows specification of the Excess Information Rate(EIR) MAX on the Policer. This represents the lower 32 bits.
1.3.6.1.4.1.2544.1.12.37.1.7.1.19Unsigned32read-writecurrent
f3L3QosPolicerEnvelopeObject
OBJECT-TYPE
This object allows specification of envelope object.
1.3.6.1.4.1.2544.1.12.37.1.7.1.20VariablePointerread-writecurrent
f3L3QosPolicerRank
OBJECT-TYPE
This object allows specification of rank value.
1.3.6.1.4.1.2544.1.12.37.1.7.1.21Integer32read-writecurrent
f3L3QosPolicerPolicingEnabled
OBJECT-TYPE
This object describes whether the policing is enabled.
1.3.6.1.4.1.2544.1.12.37.1.7.1.22TruthValueread-writecurrent
f3L3QosShaperTable
OBJECT-TYPE
A list of entries corresponding to Ethernet Access Port Quality of Service Shaper for configuration purposes. These shapers can be managed when the Access Port is in evpl mode and are relevant for traffic in the network to access direction.
1.3.6.1.4.1.2544.1.12.37.1.8not-accessiblecurrent
f3L3QosShaperEntry
OBJECT-TYPE
A conceptual row in the f3L3QosShaperTable. These entries represent a Quality of Service Shaper.
1.3.6.1.4.1.2544.1.12.37.1.8.1not-accessiblecurrent
f3L3QosShaperIndex
OBJECT-TYPE
The unique integer index value corresponding to a Quality of Service Shaper.
1.3.6.1.4.1.2544.1.12.37.1.8.1.1Integer32 (1..8)read-createcurrent
f3L3QosShaperAdminState
OBJECT-TYPE
This object represents the Administrative State of the QOS Shaper.
1.3.6.1.4.1.2544.1.12.37.1.8.1.2AdminStateread-writecurrent
f3L3QosShaperOperationalState
OBJECT-TYPE
This object represents the Operational State of the QOS Shaper.
1.3.6.1.4.1.2544.1.12.37.1.8.1.3OperationalStateread-onlycurrent
f3L3QosShaperSecondaryState
OBJECT-TYPE
This object represents the Secondary State of the QOS Shaper.
1.3.6.1.4.1.2544.1.12.37.1.8.1.4SecondaryStateread-onlycurrent
f3L3QosShaperCIRLo
OBJECT-TYPE
This object represents the Commited Information Rate(CIR) (Lower 32 bits)of a Shaper.
1.3.6.1.4.1.2544.1.12.37.1.8.1.5Unsigned32read-createcurrent
f3L3QosShaperCIRHi
OBJECT-TYPE
This object represents the Commited Information Rate(CIR) (Higher 32 bits) of a Shaper.
1.3.6.1.4.1.2544.1.12.37.1.8.1.6Unsigned32read-createcurrent
f3L3QosShaperEIRLo
OBJECT-TYPE
This object represents the Excess Information Rate(EIR) (Higher 32 bits) on the Shaper.
1.3.6.1.4.1.2544.1.12.37.1.8.1.7Unsigned32read-createcurrent
f3L3QosShaperEIRHi
OBJECT-TYPE
This object represents the Excess Information Rate(EIR) (Higher 32 bits) on the Shaper.
1.3.6.1.4.1.2544.1.12.37.1.8.1.8Unsigned32read-createcurrent
f3L3QosShaperBufferSize
OBJECT-TYPE
This object represents the Buffer Size of the Shaper.
1.3.6.1.4.1.2544.1.12.37.1.8.1.9Unsigned32read-createcurrent
f3L3QosShaperCOS
OBJECT-TYPE
This object provides the COS (Class of Service) value for the QOS Shaper.
1.3.6.1.4.1.2544.1.12.37.1.8.1.10Integer32 (0..7)read-onlycurrent
f3L3QosShaperWredGreenMinQueueThreshold
OBJECT-TYPE
This object represents the Wred green packet min queue threshold value.
1.3.6.1.4.1.2544.1.12.37.1.8.1.11Unsigned32read-createcurrent
f3L3QosShaperWredGreenMaxQueueThreshold
OBJECT-TYPE
This object represents the Wred green packet max queue threshold value.
1.3.6.1.4.1.2544.1.12.37.1.8.1.12Unsigned32read-createcurrent
f3L3QosShaperWredGreenDropProbability
OBJECT-TYPE
This object represents the Wred green packet drop probability.
1.3.6.1.4.1.2544.1.12.37.1.8.1.13Unsigned32read-createcurrent
f3L3QosShaperWredYellowMinQueueThreshold
OBJECT-TYPE
This object represents the Wred yellow packet min queue threshold value.
1.3.6.1.4.1.2544.1.12.37.1.8.1.14Unsigned32read-createcurrent
f3L3QosShaperWredYellowMaxQueueThreshold
OBJECT-TYPE
This object represents the Wred yellow packet max queue threshold value.
1.3.6.1.4.1.2544.1.12.37.1.8.1.15Unsigned32read-createcurrent
f3L3QosShaperWredYellowDropProbability
OBJECT-TYPE
This object represents the Wred yellow packet drop probability.
1.3.6.1.4.1.2544.1.12.37.1.8.1.16Unsigned32read-createcurrent
f3L3QosShaperStorageType
OBJECT-TYPE
The type of storage configured for this entry.
1.3.6.1.4.1.2544.1.12.37.1.8.1.17StorageTyperead-createcurrent
f3L3QosShaperRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3L3QosShaperRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3L3QosShaperRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3L3QosShaperRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.37.1.8.1.18RowStatusread-createcurrent
f3L3QosShaperWfqWeight
OBJECT-TYPE
This object represents wfq weight value.
1.3.6.1.4.1.2544.1.12.37.1.8.1.19Integer32read-writecurrent
f3L3TrafficIPInterfaceTable
OBJECT-TYPE
A list of entries for the L3 Traffic IP Interface.
1.3.6.1.4.1.2544.1.12.37.1.9not-accessiblecurrent
f3L3TrafficIPInterfaceEntry
OBJECT-TYPE
A conceptual row in the f3L3TrafficIPInterfaceTable.
1.3.6.1.4.1.2544.1.12.37.1.9.1not-accessiblecurrent
f3L3TrafficIPIfIndex
OBJECT-TYPE
It specifies the traffic IP interface number.
1.3.6.1.4.1.2544.1.12.37.1.9.1.1Integer32not-accessiblecurrent
f3L3TrafficIPIfName
OBJECT-TYPE
It specifies the traffic IP interface name.
1.3.6.1.4.1.2544.1.12.37.1.9.1.2DisplayString (SIZE(0..15))read-writecurrent
f3L3TrafficIPIfAdminState
OBJECT-TYPE
This object represents the Administrative State of the interface.
1.3.6.1.4.1.2544.1.12.37.1.9.1.3AdminStateread-writecurrent
f3L3TrafficIPIfSecondaryState
OBJECT-TYPE
This object represents the Secondary State of the interface.
1.3.6.1.4.1.2544.1.12.37.1.9.1.4SecondaryStateread-onlycurrent
f3L3TrafficIPIfOperationalState
OBJECT-TYPE
This object represents the Operational State of the interface.
1.3.6.1.4.1.2544.1.12.37.1.9.1.5OperationalStateread-onlycurrent
f3L3TrafficIPIfProxyArpEnabled
OBJECT-TYPE
This attribute controls poxy ARP on this interface.
1.3.6.1.4.1.2544.1.12.37.1.9.1.6TruthValueread-writecurrent
f3L3TrafficIPIfIpAddressSourceType
OBJECT-TYPE
This attribute represents the IP address source type.
1.3.6.1.4.1.2544.1.12.37.1.9.1.7IfIpAddressSourceTyperead-writecurrent
f3L3TrafficIPIfMgmtUseEnable
OBJECT-TYPE
This attribute is used for controlling use of interface for management. If enabled the NE can be managed through this interface.
1.3.6.1.4.1.2544.1.12.37.1.9.1.8TruthValueread-writecurrent
f3L3TrafficIPIfIpAddress
OBJECT-TYPE
IP Address of the interface.
1.3.6.1.4.1.2544.1.12.37.1.9.1.9IpAddressread-writecurrent
f3L3TrafficIPIfMask
OBJECT-TYPE
IP Address mask of the interface.
1.3.6.1.4.1.2544.1.12.37.1.9.1.10IpAddressread-writecurrent
f3L3TrafficIPIfDhcpRelayInterfaceSide
OBJECT-TYPE
This object represents interface side.
1.3.6.1.4.1.2544.1.12.37.1.9.1.11DhcpRelayInterfaceSideread-writecurrent
f3L3TrafficIPIfDhcpRelayVendorClassiDOpt60
OBJECT-TYPE
DHCP Option 60 value used for association of received DHCP message with Traffic IP Interface.
1.3.6.1.4.1.2544.1.12.37.1.9.1.12DisplayString (SIZE(0..255))read-writecurrent
f3L3TrafficIPIfDhcpRelayVendorClassiDOpt60Control
OBJECT-TYPE
This Attribute is used to control inspection of DHCP option 60 presence in the DHCP messages received on Client Side Traffic IP Interface.
1.3.6.1.4.1.2544.1.12.37.1.9.1.13TruthValueread-writecurrent
f3L3TrafficIPIfDhcpRelayUserClassOpt77
OBJECT-TYPE
DHCP Option 77 value used for association of received DHCP message with Traffic IP Interface .
1.3.6.1.4.1.2544.1.12.37.1.9.1.14DisplayString (SIZE(0..255))read-writecurrent
f3L3TrafficIPIfDhcpRelayUserClassOpt77Control
OBJECT-TYPE
This Attribute is used to control inspection of DHCP option 77 presence in the DHCP messages received on Client Side Traffic IP Interface.
1.3.6.1.4.1.2544.1.12.37.1.9.1.15TruthValueread-writecurrent
f3L3TrafficIPIfDhcpRelayInfoOpt82Sub1
OBJECT-TYPE
DHCP Option 82 sub option 1 value.
1.3.6.1.4.1.2544.1.12.37.1.9.1.16DisplayString (SIZE(0..255))read-writecurrent
f3L3TrafficIPIfDhcpRelayInfoOpt82Sub1Enabled
OBJECT-TYPE
This Attribute is used to control inspection of DHCP option 82 sub option 1 presence in the DHCP messages received on Client Side Traffic IP Interface.
1.3.6.1.4.1.2544.1.12.37.1.9.1.17TruthValueread-writecurrent
f3L3TrafficIPIfDhcpRelayInfoOpt82Sub2
OBJECT-TYPE
DHCP Option 82 sub option 2 value.
1.3.6.1.4.1.2544.1.12.37.1.9.1.18DisplayString (SIZE(0..255))read-writecurrent
f3L3TrafficIPIfDhcpRelayInfoOpt82Sub2Enabled
OBJECT-TYPE
This Attribute is used to control inspection of DHCP option 82 sub option 2 presence in the DHCP messages received on Client Side Traffic IP Interface.
1.3.6.1.4.1.2544.1.12.37.1.9.1.19TruthValueread-writecurrent
f3L3TrafficIPIfDhcpEnabled
OBJECT-TYPE
Whether or not DHCP is enabled on this interface.
1.3.6.1.4.1.2544.1.12.37.1.9.1.20TruthValueread-writecurrent
f3L3TrafficIPIfDhcpRole
OBJECT-TYPE
Specify the DHCP role on this interface.
1.3.6.1.4.1.2544.1.12.37.1.9.1.21CmDhcpRoleread-onlycurrent
f3L3TrafficIPIfDhcpClientIdEnabled
OBJECT-TYPE
Whether or not DHCP client id enabled.
1.3.6.1.4.1.2544.1.12.37.1.9.1.22TruthValueread-writecurrent
f3L3TrafficIPIfDhcpClientId
OBJECT-TYPE
Specify the DHCP Cliend ID value.
1.3.6.1.4.1.2544.1.12.37.1.9.1.23DisplayStringread-writecurrent
f3L3TrafficIPIfDhcpClassIdEnabled
OBJECT-TYPE
Whether or not DHCP class id enabled.
1.3.6.1.4.1.2544.1.12.37.1.9.1.24TruthValueread-writecurrent
f3L3TrafficIPIfDhcpHostNameEnabled
OBJECT-TYPE
Whether or not DHCP host name enabled.
1.3.6.1.4.1.2544.1.12.37.1.9.1.25TruthValueread-writecurrent
f3L3TrafficIPIfDhcpHostName
OBJECT-TYPE
DHCP host name value.
1.3.6.1.4.1.2544.1.12.37.1.9.1.26DisplayStringread-writecurrent
f3L3TrafficIPIfDhcpClientIdType
OBJECT-TYPE
This object describe whether the dhcp cid type.
1.3.6.1.4.1.2544.1.12.37.1.9.1.27DHCPCIDTyperead-writecurrent
f3L3TrafficIPIfDhcpHostNameType
OBJECT-TYPE
This object describe whether the dhcp host name type.
1.3.6.1.4.1.2544.1.12.37.1.9.1.28DHCPHostNameTyperead-writecurrent
f3L3TrafficIPIfStorageType
OBJECT-TYPE
The type of storage configured for this entry.
1.3.6.1.4.1.2544.1.12.37.1.9.1.29StorageTyperead-createcurrent
f3L3TrafficIPIfRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3L3TrafficIPIfRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3L3TrafficIPIfRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3L3TrafficIPIfRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.37.1.9.1.30RowStatusread-createcurrent
f3L3TrafficIPIfAction
OBJECT-TYPE
This objects describes action set on this traffic ip interface. DEPRECATED and new variable to use is f3L3TrafficIPIfActionX.
1.3.6.1.4.1.2544.1.12.37.1.9.1.31AffectiveArpActionTyperead-writedeprecated
f3L3TrafficIPIfActionX
OBJECT-TYPE
This objects describes action set on this traffic ip interface.
1.3.6.1.4.1.2544.1.12.37.1.9.1.32TrafficIpInterfaceActionTyperead-writecurrent
f3L3TrafficIPIfUnnumberedControl
OBJECT-TYPE
This object specify IP interface whether is numbered.
1.3.6.1.4.1.2544.1.12.37.1.9.1.33TruthValueread-createcurrent
f3L3TrafficIPIfBorrowedIntf
OBJECT-TYPE
This object specify IP interface name whose IP address is borrowed from currect object.
1.3.6.1.4.1.2544.1.12.37.1.9.1.34DisplayStringread-createcurrent
f3L3TrafficIPIfIpMode
OBJECT-TYPE
This object means the ip mode for the interface.
1.3.6.1.4.1.2544.1.12.37.1.9.1.35IpModeread-writecurrent
f3L3TrafficIPIfType
OBJECT-TYPE
This object represents the type of the interface.
1.3.6.1.4.1.2544.1.12.37.1.9.1.36IpInterfaceTyperead-writecurrent
f3L3TrafficIPIfIpv6LinkLocalAddr
OBJECT-TYPE
Link-local Address.
1.3.6.1.4.1.2544.1.12.37.1.9.1.37Ipv6Addressread-writecurrent
f3L3TrafficIPIfIpv6LinkLocalAddrMode
OBJECT-TYPE
The assignment mode of IPv6 Link-Local Address, only manual and automatic are applicable.
1.3.6.1.4.1.2544.1.12.37.1.9.1.38Ipv6LinkLocalAddressModeread-writecurrent
f3L3TrafficIPIfIpv6StatelessAddrAutoconfigEnabled
OBJECT-TYPE
This is the control to enable or disable stateless address auto configuration.
1.3.6.1.4.1.2544.1.12.37.1.9.1.39TruthValueread-writecurrent
f3L3TrafficIPIfDefaultGateway
OBJECT-TYPE
indicates active default GW of the interface.
1.3.6.1.4.1.2544.1.12.37.1.9.1.40Ipv6Addressread-writecurrent
f3L3TrafficIPIfIcmpErrorMsgRateLimit
OBJECT-TYPE
limit originated ICMP error messages rate in number of messages per second. The value 0xFFFF shall be used to indicate no error message limit.
1.3.6.1.4.1.2544.1.12.37.1.9.1.41Integer32read-writecurrent
f3L3TrafficIPIfDhcpv6Role
OBJECT-TYPE
Allows setting the DHCPv6 role on this interface.
1.3.6.1.4.1.2544.1.12.37.1.9.1.42CmDhcpRoleread-writecurrent
f3L3TrafficIPIfDhcpv6Enabled
OBJECT-TYPE
Allows enabling/disabling of DHCPv6 on this interface.
1.3.6.1.4.1.2544.1.12.37.1.9.1.43TruthValueread-writecurrent
f3L3TrafficIPIfDhcpRapidCommitControlEnabled
OBJECT-TYPE
This is the control to enable or disable DHCP rapid commit.
1.3.6.1.4.1.2544.1.12.37.1.9.1.44TruthValueread-writecurrent
f3L3TrafficIPIfMaxRAInterval
OBJECT-TYPE
Maximum time in seconds between generated RA messages.
1.3.6.1.4.1.2544.1.12.37.1.9.1.45Unsigned32read-writecurrent
f3L3TrafficIPIfMinRAInterval
OBJECT-TYPE
Minimum time in seconds between generated RA messages, should be less than 0.75* max-ra-interval.
1.3.6.1.4.1.2544.1.12.37.1.9.1.46Unsigned32read-writecurrent
f3L3TrafficIPIfRouterLifeTime
OBJECT-TYPE
Time in seconds the router can be used as a default router, should be larger than max-ra-interval.
1.3.6.1.4.1.2544.1.12.37.1.9.1.47Unsigned32read-writecurrent
f3L3TrafficIPIfReachableTime
OBJECT-TYPE
time in milliseconds, that a node assumes a neighbor is reachable after having received a reachability confirmation, 0 means unspecified.
1.3.6.1.4.1.2544.1.12.37.1.9.1.48Unsigned32read-writecurrent
f3L3TrafficIPIfRaDhcpMoreConfigEnabled
OBJECT-TYPE
RA More configurations via DHCP.
1.3.6.1.4.1.2544.1.12.37.1.9.1.49TruthValueread-writecurrent
f3L3TrafficIPIfRaManagedAddressConfigEnabled
OBJECT-TYPE
RA Managed Address Config Control.
1.3.6.1.4.1.2544.1.12.37.1.9.1.50TruthValueread-writecurrent
f3L3TrafficIPIfRaRDNSSOptionEnabled
OBJECT-TYPE
Control Recursive DNS server option presence in the RA messages.
1.3.6.1.4.1.2544.1.12.37.1.9.1.51TruthValueread-writecurrent
f3L3TrafficIPIfRaRDNSSLifeTime
OBJECT-TYPE
Set the Lifetime field of the RDNSS option.
1.3.6.1.4.1.2544.1.12.37.1.9.1.52Unsigned32read-writecurrent
f3L3TrafficIPIfRaDNSSList
OBJECT-TYPE
list of IPv6 addresses of DNS servers.
1.3.6.1.4.1.2544.1.12.37.1.9.1.53DisplayStringread-writecurrent
f3L3TrafficIPIfRaDefaultRouterPreference
OBJECT-TYPE
Specifies Default Router preference field in RA according to RFC4191.
1.3.6.1.4.1.2544.1.12.37.1.9.1.54NdpRaDefaultRouterPreferenceread-writecurrent
f3L3TrafficIPIfDupAddrDetectControl
OBJECT-TYPE
Allows enabling/disabling of DAD on this interface.
1.3.6.1.4.1.2544.1.12.37.1.9.1.55TruthValueread-writecurrent
f3L3TrafficIPIfDupAddrDetectTransmits
OBJECT-TYPE
Specify number of consequent NS messages sent by this interface.
1.3.6.1.4.1.2544.1.12.37.1.9.1.56Unsigned32read-writecurrent
f3L3TrafficIPIfDupAddrDetectRetransTimer
OBJECT-TYPE
Interval in ms between consecutive NS messages and as well as the time a node waits after sending the last NS before ending the DAD.
1.3.6.1.4.1.2544.1.12.37.1.9.1.57Unsigned32read-writecurrent
f3L3TrafficIPIfMTU
OBJECT-TYPE
MTU of a L3 Traffic IP Interface in bytes.
1.3.6.1.4.1.2544.1.12.37.1.9.1.58Integer32read-writecurrent
f3DhcpRelayAgentTrafficIpIfMemberTable
OBJECT-TYPE
A list of entries for the Dhcp Relay Agent Traffic Ip Interface member.
1.3.6.1.4.1.2544.1.12.37.1.10not-accessiblecurrent
f3DhcpRelayAgentTrafficIpIfMemberEntry
OBJECT-TYPE
A conceptual row in the f3DhcpRelayAgentTrafficIpIfMemberTable.
1.3.6.1.4.1.2544.1.12.37.1.10.1not-accessiblecurrent
f3DhcpRelayAgentTrafficIpIfMemberObject
OBJECT-TYPE
This object describes the traffic ip interface.
1.3.6.1.4.1.2544.1.12.37.1.10.1.1VariablePointernot-accessiblecurrent
f3DhcpRelayAgentTrafficIpIfMemberStorageType
OBJECT-TYPE
The type of storage configured for this entry.
1.3.6.1.4.1.2544.1.12.37.1.10.1.2StorageTyperead-createcurrent
f3DhcpRelayAgentTrafficIpIfMemberRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3DhcpRelayAgentTrafficIpIfMemberRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3DhcpRelayAgentTrafficIpIfMemberRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3DhcpRelayAgentTrafficIpIfMemberRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.37.1.10.1.3RowStatusread-createcurrent
f3VrfTrafficIpIfMemberTable
OBJECT-TYPE
A list of entries for the Vrf Traffic Ip Interface member.
1.3.6.1.4.1.2544.1.12.37.1.11not-accessiblecurrent
f3VrfTrafficIpIfMemberEntry
OBJECT-TYPE
A conceptual row in the f3DhcpRelayAgentTrafficIpIfMemberTable.
1.3.6.1.4.1.2544.1.12.37.1.11.1not-accessiblecurrent
f3VrfTrafficIpIfMemberObject
OBJECT-TYPE
This object describes the traffic ip interface.
1.3.6.1.4.1.2544.1.12.37.1.11.1.1VariablePointernot-accessiblecurrent
f3VrfTrafficIpIfMemberStorageType
OBJECT-TYPE
The type of storage configured for this entry.
1.3.6.1.4.1.2544.1.12.37.1.11.1.2StorageTyperead-createcurrent
f3VrfTrafficIpIfMemberRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3VrfTrafficIpIfMemberRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3VrfTrafficIpIfMemberRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3VrfTrafficIpIfMemberRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.37.1.11.1.3RowStatusread-createcurrent
f3L3TrafficIpv4RouteTable
OBJECT-TYPE
A list of entries for the L3 Traffic Ipv4 route. Must set f3VrfAction as retrieveEffectiveRoutes(4) before get data from this table.
1.3.6.1.4.1.2544.1.12.37.1.12not-accessibledeprecated
f3L3TrafficIpv4RouteEntry
OBJECT-TYPE
A conceptual row in the f3L3TrafficIpv4RouteTable.
1.3.6.1.4.1.2544.1.12.37.1.12.1not-accessibledeprecated
f3L3TrafficIpv4RouteDest
OBJECT-TYPE
It specifies the traffic Ipv4 route destination.
1.3.6.1.4.1.2544.1.12.37.1.12.1.1IpAddressread-writedeprecated
f3L3TrafficIpv4RouteMask
OBJECT-TYPE
It specifies the traffic Ipv4 route mask.
1.3.6.1.4.1.2544.1.12.37.1.12.1.2IpAddressread-writedeprecated
f3L3TrafficIpv4RouteNextHop
OBJECT-TYPE
It specifies the traffic Ipv4 route next hop.
1.3.6.1.4.1.2544.1.12.37.1.12.1.3IpAddressread-writedeprecated
f3L3TrafficIpv4RouteMetric
OBJECT-TYPE
It specifies the traffic Ipv4 route metric.
1.3.6.1.4.1.2544.1.12.37.1.12.1.4Integer32read-writedeprecated
f3L3TrafficIpv4RouteInterface
OBJECT-TYPE
It specifies the traffic Ipv4 route interface.
1.3.6.1.4.1.2544.1.12.37.1.12.1.5DisplayStringread-writedeprecated
f3L3TrafficIpv4RouteAdvertise
OBJECT-TYPE
It specifies the traffic Ipv4 route advertise.
1.3.6.1.4.1.2544.1.12.37.1.12.1.6TruthValueread-writedeprecated
f3L3TrafficIpv4RouteStatus
OBJECT-TYPE
It specifies the traffic Ipv4 route status. DEPRECATED and new attribute to use is f3L3TrafficIpv4RouteStatusX.
1.3.6.1.4.1.2544.1.12.37.1.12.1.7TrafficIpRouteStatusread-onlydeprecated
f3L3TrafficIpv4RouteSourceForwardingEnable
OBJECT-TYPE
It specifies the traffic Ipv4 route source forwarding whether enabled.
1.3.6.1.4.1.2544.1.12.37.1.12.1.8TruthValueread-writedeprecated
f3L3TrafficIpv4RouteFlags
OBJECT-TYPE
It specifies the traffic Ipv4 route flags.
1.3.6.1.4.1.2544.1.12.37.1.12.1.9RouteFlagsread-onlyobsolete
f3L3TrafficIpv4RouteStorageType
OBJECT-TYPE
The type of storage configured for this entry.
1.3.6.1.4.1.2544.1.12.37.1.12.1.10StorageTyperead-createdeprecated
f3L3TrafficIpv4RouteRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3L3TrafficIpv4RouteRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3L3TrafficIpv4RouteRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3L3TrafficIpv4RouteRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.37.1.12.1.11RowStatusread-createdeprecated
f3L3TrafficIpv4RouteType
OBJECT-TYPE
It specifies the route is dynamic or static.
1.3.6.1.4.1.2544.1.12.37.1.12.1.12IpEntryTyperead-onlydeprecated
f3L3TrafficIpv4RouteStatusX
OBJECT-TYPE
It specifies the traffic Ipv4 route status.
1.3.6.1.4.1.2544.1.12.37.1.12.1.13TrafficIpRouteStatusTyperead-onlydeprecated
f3L3TrafficIpv4RouteOrigin
OBJECT-TYPE
The origin of IP Route.
1.3.6.1.4.1.2544.1.12.37.1.12.1.14TrafficIpRouteOriginTyperead-onlydeprecated
f3L3TrafficArpTable
OBJECT-TYPE
A list of Traffic ARP entries on the NIDs. Must set f3L3TrafficIPIfActionX as optimizeArpRetrieve (1) before getting data from this table.
1.3.6.1.4.1.2544.1.12.37.1.13not-accessiblecurrent
f3L3TrafficArpEntry
OBJECT-TYPE
A conceptual row in the f3L3TrafficArpTable. Entries can be created/deleted in this table by management application action.
1.3.6.1.4.1.2544.1.12.37.1.13.1not-accessiblecurrent
f3L3TrafficArpIPAddress
OBJECT-TYPE
This object allows configuration of the ARP Entry IP Address.
1.3.6.1.4.1.2544.1.12.37.1.13.1.1IpAddressnot-accessiblecurrent
f3L3TrafficArpMacAddress
OBJECT-TYPE
This object allows management of the ARP Entry MAC Address.
1.3.6.1.4.1.2544.1.12.37.1.13.1.2MacAddressread-createcurrent
f3L3TrafficArpInterface
OBJECT-TYPE
This object allows management of the ARP Entry Interface.
1.3.6.1.4.1.2544.1.12.37.1.13.1.3DisplayStringread-onlycurrent
f3L3TrafficArpEntryType
OBJECT-TYPE
The type of ARP Entry. Note that static entries can be created.
1.3.6.1.4.1.2544.1.12.37.1.13.1.4IpEntryTyperead-writecurrent
f3L3TrafficArpStorageType
OBJECT-TYPE
The type of storage configured for this entry.
1.3.6.1.4.1.2544.1.12.37.1.13.1.5StorageTyperead-createcurrent
f3L3TrafficArpRowStatus
OBJECT-TYPE
The status of this row. The f3L3TrafficArpRowStatus object may be modified if the associated instance of this object is equal to active(1), notInService(2), or notReady(3).
1.3.6.1.4.1.2544.1.12.37.1.13.1.6RowStatusread-writecurrent
f3L3TrafficBgpRouterTable
OBJECT-TYPE
Traffic BGP Router.
1.3.6.1.4.1.2544.1.12.37.1.14not-accessiblecurrent
f3L3TrafficBgpRouterEntry
OBJECT-TYPE
A conceptual row in the f3L3TrafficBgpRouterTable. Entries can be created/deleted in this table by management application action.
1.3.6.1.4.1.2544.1.12.37.1.14.1not-accessiblecurrent
f3L3TrafficBgpRouterIndex
OBJECT-TYPE
The ID of BGP router.
1.3.6.1.4.1.2544.1.12.37.1.14.1.1Unsigned32not-accessiblecurrent
f3L3TrafficBgpRouterAdminState
OBJECT-TYPE
This object represents the Administrative State of the Traffic BGP Router.
1.3.6.1.4.1.2544.1.12.37.1.14.1.2AdminStateread-writecurrent
f3L3TrafficBgpRouterSecondaryState
OBJECT-TYPE
This object represents the Secondary State of the Traffic BGP Router.
1.3.6.1.4.1.2544.1.12.37.1.14.1.3SecondaryStateread-onlycurrent
f3L3TrafficBgpRouterOperationalState
OBJECT-TYPE
This object represents the Operational State of the Traffic BGP Router.
1.3.6.1.4.1.2544.1.12.37.1.14.1.4OperationalStateread-onlycurrent
f3L3TrafficBgpRouterId
OBJECT-TYPE
BGP Router Identifier.
1.3.6.1.4.1.2544.1.12.37.1.14.1.5IpAddressread-writecurrent
f3L3TrafficBgpRouterAsNumber
OBJECT-TYPE
Local autonomous system number of the router. Uses the 32-bit as-number type from the model in RFC 6991.
1.3.6.1.4.1.2544.1.12.37.1.14.1.6Unsigned32read-writecurrent
f3L3TrafficBgpRouterConnectedRoutesRedistControl
OBJECT-TYPE
This attribute is used to control connected route redistribution into BGP.
1.3.6.1.4.1.2544.1.12.37.1.14.1.7TruthValueread-writedeprecated
f3L3TrafficBgpRouterOspfRoutesRedistControl
OBJECT-TYPE
This attribute specifies OSPF route redistribution options False - OSPF routes are not redistributed to the BGP True - OSPF routes are redistributed to BGP.
1.3.6.1.4.1.2544.1.12.37.1.14.1.8TruthValueread-writedeprecated
f3L3TrafficBgpRouterStaticRoutesRedistControl
OBJECT-TYPE
This attribute is used to control static route redistribution into BGP.
1.3.6.1.4.1.2544.1.12.37.1.14.1.9TruthValueread-writedeprecated
f3L3TrafficBgpRouterDhcpRoutesRedistControl
OBJECT-TYPE
This attribute is used to control DHCP route redistribution into BGP.
1.3.6.1.4.1.2544.1.12.37.1.14.1.10TruthValueread-writedeprecated
f3L3TrafficBgpRouterStorageType
OBJECT-TYPE
The storage type for this conceptual row.
1.3.6.1.4.1.2544.1.12.37.1.14.1.11StorageTyperead-createcurrent
f3L3TrafficBgpRouterRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3L3TrafficBgpRouterRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3L3TrafficBgpRouterRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3L3TrafficBgpRouterRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.37.1.14.1.12RowStatusread-createcurrent
f3L3TrafficBgpRouterAction
OBJECT-TYPE
This object describes action set on this BGP Router.
1.3.6.1.4.1.2544.1.12.37.1.14.1.13BgpRouterActionTyperead-writecurrent
f3L3TrafficBgpRouterIBgpAdminDistance
OBJECT-TYPE
Administrative distance for routes learned from internal BGP (iBGP).
1.3.6.1.4.1.2544.1.12.37.1.14.1.14Unsigned32read-writecurrent
f3L3TrafficBgpRouterEBgpAdminDistance
OBJECT-TYPE
Administrative distance for routes learned from external BGP (eBGP).
1.3.6.1.4.1.2544.1.12.37.1.14.1.15Unsigned32read-writecurrent
f3L3TrafficBgpRouterEcmpMaximumPaths
OBJECT-TYPE
The maximum number of path used in ECMP for BGP routes.
1.3.6.1.4.1.2544.1.12.37.1.14.1.16Unsigned32read-writecurrent
f3L3TrafficBgpRouterRestartTime
OBJECT-TYPE
Estimated time (in seconds) for the local BGP speaker to restart a session.This value is advertise in the graceful restart BGP capability. This is a 12-bit value, referred to as Restart Time in RFC4724. Per RFC4724, the suggested default value is <= the hold-time value.
1.3.6.1.4.1.2544.1.12.37.1.14.1.17Unsigned32read-writecurrent
f3L3TrafficBgpRouterStaleRoutesTime
OBJECT-TYPE
An upper-bound on the time that stale routes will be retained by a router after a session is restarted. If an End-of-RIB (EOR) marker is received prior to this timer expiring stale-routes will be flushed upon its receipt - if no EOR is received, then when this timer expires stale paths will be purged. This timer is referred to as the Selection_Deferral_Timer in FC4724.
1.3.6.1.4.1.2544.1.12.37.1.14.1.18Unsigned32read-writecurrent
f3L3TrafficBgpRouteTable
OBJECT-TYPE
BGP routes. Must set f3L3TrafficBgpRouterAction as optimizeBgpRouteRetrieve(1) before get data from this table.
1.3.6.1.4.1.2544.1.12.37.1.15not-accessiblecurrent
f3L3TrafficBgpRouteEntry
OBJECT-TYPE
A conceptual row in the f3L3TrafficBgpRouteTable. Entries can be created/deleted in this table by management application action.
1.3.6.1.4.1.2544.1.12.37.1.15.1not-accessiblecurrent
f3L3TrafficBgpRouteNetwork
OBJECT-TYPE
Network of destination. Key of the table.
1.3.6.1.4.1.2544.1.12.37.1.15.1.1IpAddressnot-accessiblecurrent
f3L3TrafficBgpRouteMetric
OBJECT-TYPE
Metric value of this route. Key of the table.
1.3.6.1.4.1.2544.1.12.37.1.15.1.2Unsigned32not-accessiblecurrent
f3L3TrafficBgpRouteNextHop
OBJECT-TYPE
IP address of next hop. Key of the table.
1.3.6.1.4.1.2544.1.12.37.1.15.1.3IpAddressnot-accessiblecurrent
f3L3TrafficBgpRoutePath
OBJECT-TYPE
The list of AS numbers to the destination.
1.3.6.1.4.1.2544.1.12.37.1.15.1.4DisplayString (SIZE(0..1024))read-onlycurrent
f3L3TrafficBgpPeerTable
OBJECT-TYPE
Traffic BGP peer.
1.3.6.1.4.1.2544.1.12.37.1.16not-accessiblecurrent
f3L3TrafficBgpPeerEntry
OBJECT-TYPE
A conceptual row in the f3L3TrafficBgpPeerTable. Entries can be created/deleted in this table by management application action.
1.3.6.1.4.1.2544.1.12.37.1.16.1not-accessiblecurrent
f3L3TrafficBgpPeerIndex
OBJECT-TYPE
The ID of BGP peer instance.
1.3.6.1.4.1.2544.1.12.37.1.16.1.1Unsigned32not-accessiblecurrent
f3L3TrafficBgpPeerAdminState
OBJECT-TYPE
This object represents the Administrative State of the Traffic BGP Peer.
1.3.6.1.4.1.2544.1.12.37.1.16.1.2AdminStateread-writecurrent
f3L3TrafficBgpPeerSecondaryState
OBJECT-TYPE
This object represents the Secondary State of the Traffic BGP Peer.
1.3.6.1.4.1.2544.1.12.37.1.16.1.3SecondaryStateread-onlycurrent
f3L3TrafficBgpPeerOperationalState
OBJECT-TYPE
This object represents the Operational State of the Traffic BGP Peer.
1.3.6.1.4.1.2544.1.12.37.1.16.1.4OperationalStateread-onlycurrent
f3L3TrafficBgpPeerIpv4Addr
OBJECT-TYPE
BGP Neighbor IP address.
1.3.6.1.4.1.2544.1.12.37.1.16.1.5IpAddressread-writecurrent
f3L3TrafficBgpPeerAsNumber
OBJECT-TYPE
AS number of the peer.
1.3.6.1.4.1.2544.1.12.37.1.16.1.6Unsigned32read-writecurrent
f3L3TrafficBgpPeerDescription
OBJECT-TYPE
An optional textual description intended primarily for use with a peer or group.
1.3.6.1.4.1.2544.1.12.37.1.16.1.7DisplayString (SIZE(0..256))read-writecurrent
f3L3TrafficBgpPeerBgpSessionState
OBJECT-TYPE
This attribute indicates BGP session state.
1.3.6.1.4.1.2544.1.12.37.1.16.1.8BgpSessionStateTyperead-onlycurrent
f3L3TrafficBgpPeerHoldTime
OBJECT-TYPE
Time interval in seconds that a BGP session will be considered active in the absence of keepalive or other messages from the peer. The hold-time is typically set to 3x the keepalive-interval.
1.3.6.1.4.1.2544.1.12.37.1.16.1.9Unsigned32read-writecurrent
f3L3TrafficBgpPeerStartupHoldTime
OBJECT-TYPE
Value of the hold timer used before the routers have a chance to exchange open messages and agree on the real value.
1.3.6.1.4.1.2544.1.12.37.1.16.1.10Unsigned32read-writecurrent
f3L3TrafficBgpPeerKeepAliveTime
OBJECT-TYPE
Time interval in seconds between transmission of keepalive messages to the neighbor. Typically set to 1/3 the hold-time.
1.3.6.1.4.1.2544.1.12.37.1.16.1.11Unsigned32read-writecurrent
f3L3TrafficBgpPeerConnectRetryTime
OBJECT-TYPE
Time interval in seconds between attempts to establish a session with the peer.
1.3.6.1.4.1.2544.1.12.37.1.16.1.12Unsigned32read-writecurrent
f3L3TrafficBgpPeerUpdateSourceIp
OBJECT-TYPE
IP address used to update the source IP of BGP message transmitted. Normally loopback interface IP may be used to support loadsharing/redundancy between local and peer. Default value 0.0.0.0 implies no update.
1.3.6.1.4.1.2544.1.12.37.1.16.1.13IpAddressread-writecurrent
f3L3TrafficBgpPeerAuthenticationKey
OBJECT-TYPE
Authentication Key used with neighboring devices.
1.3.6.1.4.1.2544.1.12.37.1.16.1.14VariablePointerread-writecurrent
f3L3TrafficBgpPeerTimeSinceUpTransition
OBJECT-TYPE
Number of seconds since last transition to Established state.
1.3.6.1.4.1.2544.1.12.37.1.16.1.15Unsigned32read-onlycurrent
f3L3TrafficBgpPeerTimeSinceDownTransition
OBJECT-TYPE
Number of seconds since last transition out of Established state.
1.3.6.1.4.1.2544.1.12.37.1.16.1.16Unsigned32read-onlycurrent
f3L3TrafficBgpPeerStorageType
OBJECT-TYPE
The storage type for this conceptual row.
1.3.6.1.4.1.2544.1.12.37.1.16.1.17StorageTyperead-createcurrent
f3L3TrafficBgpPeerRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3L3TrafficBgpPeerRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3L3TrafficBgpPeerRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3L3TrafficBgpPeerRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.37.1.16.1.18RowStatusread-createcurrent
f3L3TrafficBgpPeerIpVersion
OBJECT-TYPE
This attribute is supported on ge11x units.
1.3.6.1.4.1.2544.1.12.37.1.16.1.19IpVersionread-writecurrent
f3L3TrafficBgpPeerIpv6Address
OBJECT-TYPE
This attribute is supported on ge11x units.
1.3.6.1.4.1.2544.1.12.37.1.16.1.20Ipv6Addressread-writecurrent
f3L3TrafficBgpPeerUpdateSourceIpv6
OBJECT-TYPE
This attribute is supported on ge11x units.
1.3.6.1.4.1.2544.1.12.37.1.16.1.21Ipv6Addressread-writecurrent
f3L3TrafficBgpPeerMultihopControl
OBJECT-TYPE
This attribute is supported on ge11x units.
1.3.6.1.4.1.2544.1.12.37.1.16.1.22TruthValueread-writecurrent
f3L3TrafficBgpPeerMultihopTtl
OBJECT-TYPE
This attribute is supported on ge11x units.
1.3.6.1.4.1.2544.1.12.37.1.16.1.23Unsigned32read-writecurrent
f3L3TrafficBgpPeerUpdateSourceInterface
OBJECT-TYPE
This attribute is supported on ge11x units.
1.3.6.1.4.1.2544.1.12.37.1.16.1.24DisplayStringread-writecurrent
f3L3TrafficBgpPeerUpdateSourceType
OBJECT-TYPE
This attribute is supported on ge11x units.
1.3.6.1.4.1.2544.1.12.37.1.16.1.25BgpUpdateSourceTyperead-writecurrent
f3L3TrafficBgpPeerLocalPreference
OBJECT-TYPE
This attribute is supported on ge11x/xgpro units.
1.3.6.1.4.1.2544.1.12.37.1.16.1.26Unsigned32read-writecurrent
f3L3TrafficBgpPeerRouteReflectorClient
OBJECT-TYPE
This attribute is supported on ge11x/xgpro units.
1.3.6.1.4.1.2544.1.12.37.1.16.1.27TruthValueread-writecurrent
f3L3TrafficBgpPeerRouteReflectorClusterId
OBJECT-TYPE
This attribute is supported on ge11x/xgpro units.
1.3.6.1.4.1.2544.1.12.37.1.16.1.28IpAddressread-writecurrent
f3L3TrafficBgpPeerBgpRouteInboundFilter
OBJECT-TYPE
This is the name of the IP Prefix List that is used as the filter for Inbound. This is a read-write value. A null string implies there is no filter.
1.3.6.1.4.1.2544.1.12.37.1.16.1.29DisplayStringread-writecurrent
f3L3TrafficBgpPeerBgpRouteOutboundFilter
OBJECT-TYPE
This is the name of the IP Prefix List that is used as the filter for Inbound. This is a read-write value. A null string implies there is no filter.
1.3.6.1.4.1.2544.1.12.37.1.16.1.30DisplayStringread-writecurrent
f3L3TrafficBgpPeerBgpGracefulRestart
OBJECT-TYPE
Enable or disable the graceful restart capability. Helper_only means the router does not support local restarting, but able to assist remote peer's restart..
1.3.6.1.4.1.2544.1.12.37.1.16.1.31BgpGracefulRestartControlTyperead-writecurrent
f3L3TrafficBgpPeerPeerRestartTime
OBJECT-TYPE
The period of time (advertised by the peer) that the peer expects a restart of a BGP session to take..
1.3.6.1.4.1.2544.1.12.37.1.16.1.32Unsigned32read-onlycurrent
f3L3TrafficBgpPeerPeerRestarting
OBJECT-TYPE
This flag indicates whether the remote neighbor is currently in the process of restarting, and hence received routes are currently stale.
1.3.6.1.4.1.2544.1.12.37.1.16.1.33TruthValueread-onlycurrent
f3VrfOspfRouterTable
OBJECT-TYPE
OSPF Router.
1.3.6.1.4.1.2544.1.12.37.1.17not-accessiblecurrent
f3VrfOspfRouterEntry
OBJECT-TYPE
A conceptual row in f3VrfOspfRouterTable.
1.3.6.1.4.1.2544.1.12.37.1.17.1not-accessiblecurrent
f3VrfOspfRouterIndex
OBJECT-TYPE
The ID of OSPF Router instance.
1.3.6.1.4.1.2544.1.12.37.1.17.1.1Unsigned32not-accessiblecurrent
f3VrfOspfRouterAdminState
OBJECT-TYPE
This object represents the Administrative State of the Traffic OSPF Router.
1.3.6.1.4.1.2544.1.12.37.1.17.1.2AdminStateread-writecurrent
f3VrfOspfRouterSecondaryState
OBJECT-TYPE
This object represents the Secondary State of the Traffic OSPF Router.
1.3.6.1.4.1.2544.1.12.37.1.17.1.3SecondaryStateread-onlycurrent
f3VrfOspfRouterOperationalState
OBJECT-TYPE
This object represents the Operational State of the Traffic OSPF Router.
1.3.6.1.4.1.2544.1.12.37.1.17.1.4OperationalStateread-onlycurrent
f3VrfOspfRouterId
OBJECT-TYPE
IP address used as Router ID for the OSPF protocol.
1.3.6.1.4.1.2544.1.12.37.1.17.1.5IpAddressread-writecurrent
f3VrfOspfRouterDescription
OBJECT-TYPE
The description of OSPF router.
1.3.6.1.4.1.2544.1.12.37.1.17.1.6DisplayString (SIZE(0..256))read-writecurrent
f3VrfOspfRouterBgpRoutesRedistributeToOspf
OBJECT-TYPE
This attribute is used to control redistribution of dynamic routes learnt via BGP into OSPF.
1.3.6.1.4.1.2544.1.12.37.1.17.1.7TruthValueread-writecurrent
f3VrfOspfRouterBgpRoutesMetricType
OBJECT-TYPE
Metric type of the BGP routes redistributed to OSPF.
1.3.6.1.4.1.2544.1.12.37.1.17.1.8RoutesMetricTyperead-writecurrent
f3VrfOspfRouterBgpRoutesMetric
OBJECT-TYPE
Metric value of the BGP routes redistributed to OSPF.
1.3.6.1.4.1.2544.1.12.37.1.17.1.9Unsigned32read-writecurrent
f3VrfOspfRouterStaticRoutesRedistributeToOspf
OBJECT-TYPE
This attribute is used to control redistribution of static routes into OSPF.
1.3.6.1.4.1.2544.1.12.37.1.17.1.10TruthValueread-writecurrent
f3VrfOspfRouterStaticRoutesMetricType
OBJECT-TYPE
Metric type of the static routes redistributed to OSPF.
1.3.6.1.4.1.2544.1.12.37.1.17.1.11RoutesMetricTyperead-writecurrent
f3VrfOspfRouterStaticRoutesMetric
OBJECT-TYPE
Metric value of the static routes redistributed to OSPF.
1.3.6.1.4.1.2544.1.12.37.1.17.1.12Unsigned32read-writecurrent
f3VrfOspfRouterConnectedRoutesRedistributeToOspf
OBJECT-TYPE
This attribute is used to control redistribution of connected routes into OSPF.
1.3.6.1.4.1.2544.1.12.37.1.17.1.13TruthValueread-writecurrent
f3VrfOspfRouterConnectedRoutesMetricType
OBJECT-TYPE
Metric type of the connected routes redistributed to OSPF.
1.3.6.1.4.1.2544.1.12.37.1.17.1.14RoutesMetricTyperead-writecurrent
f3VrfOspfRouterConnectedRoutesMetric
OBJECT-TYPE
Metric value of the connected routes redistributed to OSPF.
1.3.6.1.4.1.2544.1.12.37.1.17.1.15Unsigned32read-writecurrent
f3VrfOspfRouterDhcpRoutesRedistributeToOspf
OBJECT-TYPE
This attribute is used to control redistribution of dynamic routes learnt via DHCP into OSPF.
1.3.6.1.4.1.2544.1.12.37.1.17.1.16TruthValueread-writecurrent
f3VrfOspfRouterDhcpRoutesMetricType
OBJECT-TYPE
Metric type of the DHCP routes redistributed to OSPF.
1.3.6.1.4.1.2544.1.12.37.1.17.1.17RoutesMetricTyperead-writecurrent
f3VrfOspfRouterDhcpRoutesMetric
OBJECT-TYPE
Metric value of the DHCP routes redistributed to OSPF.
1.3.6.1.4.1.2544.1.12.37.1.17.1.18Unsigned32read-writecurrent
f3VrfOspfRouterIsAbr
OBJECT-TYPE
.
1.3.6.1.4.1.2544.1.12.37.1.17.1.19TruthValueread-onlycurrent
f3VrfOspfRouterIsAsbr
OBJECT-TYPE
.
1.3.6.1.4.1.2544.1.12.37.1.17.1.20TruthValueread-onlycurrent
f3VrfOspfRouterStorageType
OBJECT-TYPE
The storage type for this conceptual row.
1.3.6.1.4.1.2544.1.12.37.1.17.1.21StorageTyperead-createcurrent
f3VrfOspfRouterRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3VrfOspfRouterRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3VrfOspfRouterRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3VrfOspfRouterRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.37.1.17.1.22RowStatusread-createcurrent
f3VrfOspfRouterAction
OBJECT-TYPE
The Ospf Router action.
1.3.6.1.4.1.2544.1.12.37.1.17.1.23OspfRouterActionTyperead-writecurrent
f3VrfOspfRouterVersion
OBJECT-TYPE
The version of the Ospf Router.
1.3.6.1.4.1.2544.1.12.37.1.17.1.24OspfVersionread-writecurrent
f3VrfOspfRouterAdministrativeDistance
OBJECT-TYPE
The Administrative Distance of the Ospf Router.
1.3.6.1.4.1.2544.1.12.37.1.17.1.25Unsigned32read-writecurrent
f3VrfOspfRouterSlaacRoutesRedistributeToOspf
OBJECT-TYPE
This attribute is used to control redistribution of dynamic routes learnt via SLAAC into OSPF.
1.3.6.1.4.1.2544.1.12.37.1.17.1.26TruthValueread-writecurrent
f3VrfOspfRouterSlaacRoutesMetricType
OBJECT-TYPE
Metric type of the SLAAC routes redistributed to OSPF.
1.3.6.1.4.1.2544.1.12.37.1.17.1.27RoutesMetricTyperead-writecurrent
f3VrfOspfRouterSlaacRoutesMetric
OBJECT-TYPE
Metric value of the SLAAC routes redistributed to OSPF.
1.3.6.1.4.1.2544.1.12.37.1.17.1.28Unsigned32read-writecurrent
f3VrfOspfRouterEcmpMaximumPaths
OBJECT-TYPE
The maximum number of path used in ECMP for OSPF routes.
1.3.6.1.4.1.2544.1.12.37.1.17.1.29Unsigned32read-writecurrent
f3VrfOspfRouterSrControl
OBJECT-TYPE
Segment Routing Control.
1.3.6.1.4.1.2544.1.12.37.1.17.1.30TruthValueread-writecurrent
f3VrfOspfRouterConvergenceTime
OBJECT-TYPE
Convergence Time.
1.3.6.1.4.1.2544.1.12.37.1.17.1.31Unsigned32read-writecurrent
f3L3TrafficOspfAreaTable
OBJECT-TYPE
Traffic OSPF Area.
1.3.6.1.4.1.2544.1.12.37.1.18not-accessiblecurrent
f3L3TrafficOspfAreaEntry
OBJECT-TYPE
A conceptual row in f3L3TrafficOspfAreaTable.
1.3.6.1.4.1.2544.1.12.37.1.18.1not-accessiblecurrent
f3L3TrafficOspfAreaIndex
OBJECT-TYPE
The ID of OSPF Area instance.
1.3.6.1.4.1.2544.1.12.37.1.18.1.1Unsigned32not-accessiblecurrent
f3L3TrafficOspfAreaType
OBJECT-TYPE
OSPF Area Type.
1.3.6.1.4.1.2544.1.12.37.1.18.1.2TrafficOspfAreaTyperead-writecurrent
f3L3TrafficOspfAreaDefaultCost
OBJECT-TYPE
The cost of a default route propagated to stub area.
1.3.6.1.4.1.2544.1.12.37.1.18.1.3Unsigned32read-writecurrent
f3L3TrafficOspfAreaId
OBJECT-TYPE
The 32-bit number identifying the area.
1.3.6.1.4.1.2544.1.12.37.1.18.1.4IpAddressread-writecurrent
f3L3TrafficOspfAreaStorageType
OBJECT-TYPE
The storage type for this conceptual row.
1.3.6.1.4.1.2544.1.12.37.1.18.1.5StorageTyperead-createcurrent
f3L3TrafficOspfAreaRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3L3TrafficOspfAreaRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3L3TrafficOspfAreaRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3L3TrafficOspfAreaRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.37.1.18.1.6RowStatusread-createcurrent
f3L3TrafficOspfAreaAuthType
OBJECT-TYPE
This attribute is used to specify authentication type.
1.3.6.1.4.1.2544.1.12.37.1.18.1.7OspfAuthTyperead-writecurrent
f3L3TrafficOspfAreaSimpleAuthKey
OBJECT-TYPE
The attribute is used to specify simple authentication key.
1.3.6.1.4.1.2544.1.12.37.1.18.1.8DisplayStringread-writecurrent
f3L3TrafficOspfAreaCryptoKeyId
OBJECT-TYPE
Authentication Key Id.
1.3.6.1.4.1.2544.1.12.37.1.18.1.9VariablePointerread-writecurrent
f3L3TrafficOspfAreaIfMemberTable
OBJECT-TYPE
OSPF Area Interface Member.
1.3.6.1.4.1.2544.1.12.37.1.19not-accessiblecurrent
f3L3TrafficOspfAreaIfMemberEntry
OBJECT-TYPE
A conceptual row in f3L3TrafficOspfAreaIfMemberTable.
1.3.6.1.4.1.2544.1.12.37.1.19.1not-accessiblecurrent
f3L3TrafficOspfAreaIfMemberObject
OBJECT-TYPE
OSPF Area Interface Member.
1.3.6.1.4.1.2544.1.12.37.1.19.1.1VariablePointernot-accessiblecurrent
f3L3TrafficOspfAreaIfMemberStorageType
OBJECT-TYPE
The storage type for this conceptual row.
1.3.6.1.4.1.2544.1.12.37.1.19.1.2StorageTyperead-createcurrent
f3L3TrafficOspfAreaIfMemberRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3L3TrafficOspfAreaIfMemberRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3L3TrafficOspfAreaIfMemberRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3L3TrafficOspfAreaIfMemberRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.37.1.19.1.3RowStatusread-createcurrent
f3VrfLoopbackInterfaceTable
OBJECT-TYPE
.
1.3.6.1.4.1.2544.1.12.37.1.20not-accessiblecurrent
f3VrfLoopbackInterfaceEntry
OBJECT-TYPE
A conceptual row in f3VrfLoopbackInterfaceTable.
1.3.6.1.4.1.2544.1.12.37.1.20.1not-accessiblecurrent
f3VrfLoopbackInterfaceIndex
OBJECT-TYPE
.
1.3.6.1.4.1.2544.1.12.37.1.20.1.1Unsigned32not-accessiblecurrent
f3VrfLoopbackInterfaceName
OBJECT-TYPE
.
1.3.6.1.4.1.2544.1.12.37.1.20.1.2DisplayString (SIZE(0..15))read-writecurrent
f3VrfLoopbackInterfaceIpAddress
OBJECT-TYPE
.
1.3.6.1.4.1.2544.1.12.37.1.20.1.3IpAddressread-writecurrent
f3VrfLoopbackInterfaceNetMask
OBJECT-TYPE
.
1.3.6.1.4.1.2544.1.12.37.1.20.1.4IpAddressread-writecurrent
f3VrfLoopbackInterfaceCIRLo
OBJECT-TYPE
.
1.3.6.1.4.1.2544.1.12.37.1.20.1.5Unsigned32read-writecurrent
f3VrfLoopbackInterfaceCIRHi
OBJECT-TYPE
.
1.3.6.1.4.1.2544.1.12.37.1.20.1.6Unsigned32read-writecurrent
f3VrfLoopbackInterfaceStorageType
OBJECT-TYPE
The storage type for this conceptual row.
1.3.6.1.4.1.2544.1.12.37.1.20.1.7StorageTyperead-createcurrent
f3VrfLoopbackInterfaceRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3VrfLoopbackInterfaceRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3VrfLoopbackInterfaceRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3VrfLoopbackInterfaceRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.37.1.20.1.8RowStatusread-createcurrent
f3VrfLoopbackInterfaceIpMode
OBJECT-TYPE
This object means the ip mode for the interface.
1.3.6.1.4.1.2544.1.12.37.1.20.1.9IpModeread-writecurrent
f3VrfLoopbackInterfaceIpv6Address
OBJECT-TYPE
This object means the ipv6 address for the interface.
1.3.6.1.4.1.2544.1.12.37.1.20.1.10Ipv6Addressread-writecurrent
f3VrfLoopbackInterfaceIpv6AddrPrefixLen
OBJECT-TYPE
This object means the ipv6 address prefix length for the interface.
1.3.6.1.4.1.2544.1.12.37.1.20.1.11Integer32read-writecurrent
f3L3TrafficOspfAsLsDbTable
OBJECT-TYPE
OSPF AS Link State Database. Must set f3VrfOspfRouterAction as optimizeOspfAsLsDbRetrieve(1) before get data from this table.
1.3.6.1.4.1.2544.1.12.37.1.21not-accessiblecurrent
f3L3TrafficOspfAsLsDbEntry
OBJECT-TYPE
A conceptual row in the f3L3TrafficOspfAsLsDbTable. Entries can be created/deleted in this table by management application action.
1.3.6.1.4.1.2544.1.12.37.1.21.1not-accessiblecurrent
f3L3TrafficOspfAsLsDbType
OBJECT-TYPE
LSA Type.
1.3.6.1.4.1.2544.1.12.37.1.21.1.1OspfAsLsaTypenot-accessiblecurrent
f3L3TrafficOspfAsLsDbId
OBJECT-TYPE
Link State ID.
1.3.6.1.4.1.2544.1.12.37.1.21.1.2IpAddressnot-accessiblecurrent
f3L3TrafficOspfAsLsDbRouterId
OBJECT-TYPE
LSA advertising router.
1.3.6.1.4.1.2544.1.12.37.1.21.1.3IpAddressnot-accessiblecurrent
f3L3TrafficOspfAsLsDbChecksum
OBJECT-TYPE
The checksum associated with Link State Advertisement.
1.3.6.1.4.1.2544.1.12.37.1.21.1.4Unsigned32read-onlycurrent
f3L3TrafficOspfAsLsDbSeqNum
OBJECT-TYPE
The Sequence Number associated with the last LSA.
1.3.6.1.4.1.2544.1.12.37.1.21.1.5Unsigned32read-onlycurrent
f3L3TrafficOspfAsLsDbAge
OBJECT-TYPE
The age, in seconds, since this LSA was last received.
1.3.6.1.4.1.2544.1.12.37.1.21.1.6Unsigned32read-onlycurrent
f3L3TrafficOspfLsDbTable
OBJECT-TYPE
OSPF Link State database. Must set f3VrfOspfRouterAction as optimizeOspfLsDbRetrieve(2) before get data from this table.
1.3.6.1.4.1.2544.1.12.37.1.22not-accessiblecurrent
f3L3TrafficOspfLsDbEntry
OBJECT-TYPE
A conceptual row in the f3L3TrafficOspfLsDbTable. Entries can be created/deleted in this table by management application action.
1.3.6.1.4.1.2544.1.12.37.1.22.1not-accessiblecurrent
f3L3TrafficOspfLsDbType
OBJECT-TYPE
LSA Type.
1.3.6.1.4.1.2544.1.12.37.1.22.1.1OspfLsaTypenot-accessiblecurrent
f3L3TrafficOspfLsDbId
OBJECT-TYPE
Link State ID.
1.3.6.1.4.1.2544.1.12.37.1.22.1.2IpAddressnot-accessiblecurrent
f3L3TrafficOspfLsDbRouterId
OBJECT-TYPE
Advertising Router ID.
1.3.6.1.4.1.2544.1.12.37.1.22.1.3IpAddressnot-accessiblecurrent
f3L3TrafficOspfLsDbAreaId
OBJECT-TYPE
Area ID.
1.3.6.1.4.1.2544.1.12.37.1.22.1.4IpAddressnot-accessiblecurrent
f3L3TrafficOspfLsDbChecksum
OBJECT-TYPE
The checksum associated with Link State Advertisement.
1.3.6.1.4.1.2544.1.12.37.1.22.1.5Unsigned32read-onlycurrent
f3L3TrafficOspfLsDbSeqNum
OBJECT-TYPE
The Sequence Number associated with the last LSA.
1.3.6.1.4.1.2544.1.12.37.1.22.1.6Unsigned32read-onlycurrent
f3L3TrafficOspfLsDbAge
OBJECT-TYPE
The age, in seconds, since this LSA was last received.
1.3.6.1.4.1.2544.1.12.37.1.22.1.7Unsigned32read-onlycurrent
f3L3TrafficOspfNeighborTable
OBJECT-TYPE
OSPF neighbor table. Must set f3VrfOspfRouterAction as optimizeOspfNeighborRetrieve(3) before get data from this table.
1.3.6.1.4.1.2544.1.12.37.1.23not-accessiblecurrent
f3L3TrafficOspfNeighborEntry
OBJECT-TYPE
A conceptual row in the f3L3TrafficOspfNeighborTable. Entries can be created/deleted in this table by management application action.
1.3.6.1.4.1.2544.1.12.37.1.23.1not-accessiblecurrent
f3L3TrafficOspfNeighborIpAddress
OBJECT-TYPE
Address of interface of neighbor.
1.3.6.1.4.1.2544.1.12.37.1.23.1.1IpAddressnot-accessiblecurrent
f3L3TrafficOspfNeighborInterface
OBJECT-TYPE
The local interface which discovers the neighbor.
1.3.6.1.4.1.2544.1.12.37.1.23.1.2VariablePointerread-onlydeprecated
f3L3TrafficOspfNeighborRouterId
OBJECT-TYPE
Router ID of the neighbor.
1.3.6.1.4.1.2544.1.12.37.1.23.1.3IpAddressread-onlycurrent
f3L3TrafficOspfNeighborState
OBJECT-TYPE
State of Link State Database synchronization with the neighbor.
1.3.6.1.4.1.2544.1.12.37.1.23.1.4OspfAdjacencyStateread-onlycurrent
f3L3TrafficOspfNeighborRole
OBJECT-TYPE
Role of the neighbor. DR, DR other and Backup are applicable.
1.3.6.1.4.1.2544.1.12.37.1.23.1.5TrafficOspfRoleread-onlycurrent
f3L3TrafficOspfNeighborPriority
OBJECT-TYPE
The priority of the neighbor.
1.3.6.1.4.1.2544.1.12.37.1.23.1.6Unsigned32read-onlycurrent
f3L3TrafficOspfNeighborDeadTime
OBJECT-TYPE
The Dead Time field indicates the amount of time remaining that the router waits to receive an OSPF hello packet from the neighbor before declaring the neighbor down.
1.3.6.1.4.1.2544.1.12.37.1.23.1.7Unsigned32read-onlycurrent
f3L3TrafficOspfNeighborLocalInterfaceName
OBJECT-TYPE
The name of local interface which discovers the neighbor.
1.3.6.1.4.1.2544.1.12.37.1.23.1.8DisplayStringread-onlycurrent
f3L3TrafficIPInterfaceOspfTable
OBJECT-TYPE
OSPF Traffic IP Interface Attributes.
1.3.6.1.4.1.2544.1.12.37.1.25not-accessiblecurrent
f3L3TrafficIPInterfaceOspfEntry
OBJECT-TYPE
A conceptual row in the f3L3TrafficIPInterfaceOspfTable.
1.3.6.1.4.1.2544.1.12.37.1.25.1not-accessiblecurrent
f3L3TrafficIPIfOspfAreaId
OBJECT-TYPE
A 32-bit number identifying the area.
1.3.6.1.4.1.2544.1.12.37.1.25.1.1IpAddressread-onlycurrent
f3L3TrafficIPIfOspfCost
OBJECT-TYPE
The cost of the route during the SPF calculation.
1.3.6.1.4.1.2544.1.12.37.1.25.1.2Unsigned32read-writecurrent
f3L3TrafficIPIfOspfIfType
OBJECT-TYPE
Interface network type.
1.3.6.1.4.1.2544.1.12.37.1.25.1.3OspfIfTyperead-writecurrent
f3L3TrafficIPIfOspfRtrPriority
OBJECT-TYPE
An 8-bit unsigned integer, used for DR and BDR election, may be default. 0 means not to attend DR election.
1.3.6.1.4.1.2544.1.12.37.1.25.1.4Unsigned32read-writecurrent
f3L3TrafficIPIfOspfHelloInterval
OBJECT-TYPE
The interval in seconds between Hello Packets that the router sends on the interface.
1.3.6.1.4.1.2544.1.12.37.1.25.1.5Unsigned32read-writecurrent
f3L3TrafficIPIfOspfDeadInterval
OBJECT-TYPE
The number of seconds before the router's neighbors will declare it down, when they stop hearing the router's Hello Packets.
1.3.6.1.4.1.2544.1.12.37.1.25.1.6Unsigned32read-writecurrent
f3L3TrafficIPIfOspfTransmitDelay
OBJECT-TYPE
2~65535 Default 2s The estimated number of seconds it takes to transmit a Link State Update Packet over this interface. LSAs contained in the Link State update packet will have their age incremented by this amount before transmission. This value should take into account transmission and propagation delays; it must be greater than 1.
1.3.6.1.4.1.2544.1.12.37.1.25.1.7Unsigned32read-writecurrent
f3L3TrafficIPIfOspfRetransmitInterval
OBJECT-TYPE
The number of seconds between LSA retransmissions, for adjacencies belonging to this interface. Also used when retransmitting Database Description and Link State Request Packets.
1.3.6.1.4.1.2544.1.12.37.1.25.1.8Unsigned32read-writecurrent
f3L3TrafficIPIfOspfState
OBJECT-TYPE
OSPF Interface state.
1.3.6.1.4.1.2544.1.12.37.1.25.1.9OspfInterfaceStateread-onlycurrent
f3L3TrafficIPIfOspfDesignatedRouterId
OBJECT-TYPE
Designated Router IP interface on the Network.
1.3.6.1.4.1.2544.1.12.37.1.25.1.10IpAddressread-onlycurrent
f3L3TrafficIPIfOspfBackupDesignatedRouterId
OBJECT-TYPE
Backup Designated Router IP interface on the Network.
1.3.6.1.4.1.2544.1.12.37.1.25.1.11IpAddressread-onlycurrent
f3L3TrafficIPIfOspfAuthType
OBJECT-TYPE
This attribute is used to specify authentication type. Simple: 64-bits clear password inserted into OSPF packets header. None: No authentication is used. Cryptographic: a shared secret which enables the generation/verification of message digests which are appended to the OSPF protocol packets.
1.3.6.1.4.1.2544.1.12.37.1.25.1.12OspfAuthTyperead-writecurrent
f3L3TrafficIPIfOspfSimpleAuthKey
OBJECT-TYPE
Authentication key.
1.3.6.1.4.1.2544.1.12.37.1.25.1.13DisplayStringread-writecurrent
f3L3TrafficIPIfospfCryptoKeyId
OBJECT-TYPE
Crypto key Id.
1.3.6.1.4.1.2544.1.12.37.1.25.1.14VariablePointerread-writecurrent
f3L3TrafficIPv6InterfaceTable
OBJECT-TYPE
A list of entries for the L3 Traffic IPv6 Interface.
1.3.6.1.4.1.2544.1.12.37.1.26not-accessiblecurrent
f3L3TrafficIPv6InterfaceEntry
OBJECT-TYPE
A conceptual row in the f3L3TrafficIPv6InterfaceTable.
1.3.6.1.4.1.2544.1.12.37.1.26.1not-accessiblecurrent
f3L3TrafficIPv6IfIndex
OBJECT-TYPE
It specifies the traffic IPv6 interface number.
1.3.6.1.4.1.2544.1.12.37.1.26.1.1Integer32not-accessiblecurrent
f3L3TrafficIPv6IfName
OBJECT-TYPE
It specifies the traffic IPv6 interface name.
1.3.6.1.4.1.2544.1.12.37.1.26.1.2DisplayString (SIZE(0..15))read-writecurrent
f3L3TrafficIPv6IfAdminState
OBJECT-TYPE
This object represents the Administrative State of the interface.
1.3.6.1.4.1.2544.1.12.37.1.26.1.3AdminStateread-writecurrent
f3L3TrafficIPv6IfSecondaryState
OBJECT-TYPE
This object represents the Secondary State of the interface.
1.3.6.1.4.1.2544.1.12.37.1.26.1.4SecondaryStateread-onlycurrent
f3L3TrafficIPv6IfOperationalState
OBJECT-TYPE
This object represents the Operational State of the interface.
1.3.6.1.4.1.2544.1.12.37.1.26.1.5OperationalStateread-onlycurrent
f3L3TrafficIPv6IfType
OBJECT-TYPE
This object represents the type of the interface.
1.3.6.1.4.1.2544.1.12.37.1.26.1.6IpInterfaceTyperead-writecurrent
f3L3TrafficIPv6IfLinkLocalAddr
OBJECT-TYPE
Link-local Address.
1.3.6.1.4.1.2544.1.12.37.1.26.1.7Ipv6Addressread-writecurrent
f3L3TrafficIPv6IfLinkLocalAddrMode
OBJECT-TYPE
The assignment mode of IPv6 Link-Local Address, only manual and automatic are applicable.
1.3.6.1.4.1.2544.1.12.37.1.26.1.8Ipv6LinkLocalAddressModeread-writecurrent
f3L3TrafficIPv6IfMtu
OBJECT-TYPE
This is the MTU for IPv6 Traffic interface.
1.3.6.1.4.1.2544.1.12.37.1.26.1.9Integer32read-onlycurrent
f3L3TrafficIPv6IfStatelessAddrAutoconfigEnabled
OBJECT-TYPE
This is the control to enable or disable stateless address auto configuration.
1.3.6.1.4.1.2544.1.12.37.1.26.1.10TruthValueread-writecurrent
f3L3TrafficIPv6IfDefaultGateway
OBJECT-TYPE
indicates active default GW of the interface.
1.3.6.1.4.1.2544.1.12.37.1.26.1.11Ipv6Addressread-writecurrent
f3L3TrafficIPv6IfIcmpErrorMsgRateLimit
OBJECT-TYPE
limit originated ICMP error messages rate in number of messages per second. The value 0xFFFF shall be used to indicate no error message limit.
1.3.6.1.4.1.2544.1.12.37.1.26.1.12Integer32read-writecurrent
f3L3TrafficIPv6IfDhcpRole
OBJECT-TYPE
Allows setting the DHCPv6 role on this interface.
1.3.6.1.4.1.2544.1.12.37.1.26.1.13CmDhcpRoleread-writecurrent
f3L3TrafficIPv6IfDhcpEnabled
OBJECT-TYPE
Allows enabling/disabling of DHCPv6 on this interface.
1.3.6.1.4.1.2544.1.12.37.1.26.1.14TruthValueread-writecurrent
f3L3TrafficIPv6IfDhcpRapidCommitControlEnabled
OBJECT-TYPE
This is the control to enable or disable DHCP rapid commit.
1.3.6.1.4.1.2544.1.12.37.1.26.1.15TruthValueread-writecurrent
f3L3TrafficIPv6IfMaxRAInterval
OBJECT-TYPE
Maximum time in seconds between generated RA messages.
1.3.6.1.4.1.2544.1.12.37.1.26.1.16Unsigned32read-writecurrent
f3L3TrafficIPv6IfMinRAInterval
OBJECT-TYPE
Minimum time in seconds between generated RA messages, should be less than 0.75* max-ra-interval.
1.3.6.1.4.1.2544.1.12.37.1.26.1.17Unsigned32read-writecurrent
f3L3TrafficIPv6IfRouterLifeTime
OBJECT-TYPE
Time in seconds the router can be used as a default router, should be larger than max-ra-interval.
1.3.6.1.4.1.2544.1.12.37.1.26.1.18Unsigned32read-writecurrent
f3L3TrafficIPv6IfReachableTime
OBJECT-TYPE
time in milliseconds, that a node assumes a neighbor is reachable after having received a reachability confirmation, 0 means unspecified.
1.3.6.1.4.1.2544.1.12.37.1.26.1.19Unsigned32read-writecurrent
f3L3TrafficIPv6IfRaDhcpMoreConfigEnabled
OBJECT-TYPE
RA More configurations via DHCP.
1.3.6.1.4.1.2544.1.12.37.1.26.1.20TruthValueread-writecurrent
f3L3TrafficIPv6IfRaManagedAddressConfigEnabled
OBJECT-TYPE
RA Managed Address Config Control.
1.3.6.1.4.1.2544.1.12.37.1.26.1.21TruthValueread-writecurrent
f3L3TrafficIPv6IfRaRDNSSOptionEnabled
OBJECT-TYPE
Control Recursive DNS server option presence in the RA messages.
1.3.6.1.4.1.2544.1.12.37.1.26.1.22TruthValueread-writecurrent
f3L3TrafficIPv6IfRaRDNSSLifeTime
OBJECT-TYPE
Set the Lifetime field of the RDNSS option.
1.3.6.1.4.1.2544.1.12.37.1.26.1.23Unsigned32read-writecurrent
f3L3TrafficIPv6IfRaDNSSList
OBJECT-TYPE
list of IPv6 addresses of DNS servers.
1.3.6.1.4.1.2544.1.12.37.1.26.1.24DisplayStringread-writecurrent
f3L3TrafficIPv6IfRaDefaultRouterPreference
OBJECT-TYPE
Specifies Default Router preference field in RA according to RFC4191.
1.3.6.1.4.1.2544.1.12.37.1.26.1.25NdpRaDefaultRouterPreferenceread-writecurrent
f3L3TrafficIPv6IfDupAddrDetectControl
OBJECT-TYPE
Allows enabling/disabling of DAD on this interface.
1.3.6.1.4.1.2544.1.12.37.1.26.1.26TruthValueread-writecurrent
f3L3TrafficIPv6IfDupAddrDetectTransmits
OBJECT-TYPE
Specify number of consequent NS messages sent by this interface.
1.3.6.1.4.1.2544.1.12.37.1.26.1.27Unsigned32read-writecurrent
f3L3TrafficIPv6IfDupAddrDetectRetransTimer
OBJECT-TYPE
Interval in ms between consecutive NS messages and as well as the time a node waits after sending the last NS before ending the DAD.
1.3.6.1.4.1.2544.1.12.37.1.26.1.28Unsigned32read-writecurrent
f3L3TrafficIPv6IfStorageType
OBJECT-TYPE
The storage type for this conceptual row.
1.3.6.1.4.1.2544.1.12.37.1.26.1.29StorageTyperead-createcurrent
f3L3TrafficIPv6IfRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3L3TrafficIPv6IfRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3L3TrafficIPv6IfRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3L3TrafficIPv6IfRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.37.1.26.1.30RowStatusread-createcurrent
f3L3TrafficIPv6IfAction
OBJECT-TYPE
This objects describes action set on this traffic ip interface.
1.3.6.1.4.1.2544.1.12.37.1.26.1.31TrafficIpv6InterfaceActionTyperead-writecurrent
f3L3TrafficIPv6AddressTable
OBJECT-TYPE
Traffic IPv6 interface address table.
1.3.6.1.4.1.2544.1.12.37.1.27not-accessiblecurrent
f3L3TrafficIPv6AddressEntry
OBJECT-TYPE
A conceptual row in the f3L3TrafficIPv6AddressTable.
1.3.6.1.4.1.2544.1.12.37.1.27.1not-accessiblecurrent
f3L3TrafficIPv6AddrIndex
OBJECT-TYPE
The unique integer index value corresponding to a traffic ipv6 interface unicast address.
1.3.6.1.4.1.2544.1.12.37.1.27.1.1Integer32not-accessiblecurrent
f3L3TrafficIPv6AddrAssignMode
OBJECT-TYPE
The assignment mode of IPv6 Unicast Address.
1.3.6.1.4.1.2544.1.12.37.1.27.1.2Ipv6AddressAssignModeread-writecurrent
f3L3TrafficIPv6AddrUnicastAddr
OBJECT-TYPE
This is IPv6 Unicast Address.
1.3.6.1.4.1.2544.1.12.37.1.27.1.3Ipv6Addressread-writecurrent
f3L3TrafficIPv6AddrUnicastAddrPrefixLength
OBJECT-TYPE
This is prefix length of the unicast address.
1.3.6.1.4.1.2544.1.12.37.1.27.1.4Integer32read-writecurrent
f3L3TrafficIPv6AddrUnicastAddrAutoGenPrefix
OBJECT-TYPE
This is prefix of the unicast address in automatic address assignment mode.
1.3.6.1.4.1.2544.1.12.37.1.27.1.5DisplayStringread-writecurrent
f3L3TrafficIPv6AddrStorageType
OBJECT-TYPE
The storage type for this conceptual row.
1.3.6.1.4.1.2544.1.12.37.1.27.1.6StorageTyperead-createcurrent
f3L3TrafficIPv6AddrRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3L3TrafficIPv6AddrRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3L3TrafficIPv6AddrRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3L3TrafficIPv6AddrRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.37.1.27.1.7RowStatusread-createcurrent
f3L3TrafficIPv6PrefixTable
OBJECT-TYPE
Traffic IPv6 RA prefix table.
1.3.6.1.4.1.2544.1.12.37.1.28not-accessiblecurrent
f3L3TrafficIPv6PrefixEntry
OBJECT-TYPE
A conceptual row in f3L3TrafficIPv6PrefixTable.
1.3.6.1.4.1.2544.1.12.37.1.28.1not-accessiblecurrent
f3L3TrafficIPv6PrefixIndex
OBJECT-TYPE
The unique integer index value corresponding to a traffic ipv6 interface ra prefix.
1.3.6.1.4.1.2544.1.12.37.1.28.1.1Integer32not-accessiblecurrent
f3L3TrafficIPv6PrefixRaPrefixAdvEnabled
OBJECT-TYPE
This attribute is to enable to Advertise prefix to link in router mode.
1.3.6.1.4.1.2544.1.12.37.1.28.1.2TruthValueread-writecurrent
f3L3TrafficIPv6PrefixRaPrefix
OBJECT-TYPE
This is the IPv6 Prefix to be dispatched to the link in Router mode.
1.3.6.1.4.1.2544.1.12.37.1.28.1.3Ipv6Addressread-writecurrent
f3L3TrafficIPv6PrefixRaPrefixLength
OBJECT-TYPE
Prefix length.
1.3.6.1.4.1.2544.1.12.37.1.28.1.4Integer32read-writecurrent
f3L3TrafficIPv6PrefixValidLifeTime
OBJECT-TYPE
This attribute is used to specify fixed Valid lifetime of distributed prefix in seconds All ones may be set for unlimited lifetime.
1.3.6.1.4.1.2544.1.12.37.1.28.1.5Unsigned32read-writecurrent
f3L3TrafficIPv6PrefixPreferredLifeTime
OBJECT-TYPE
This attribute is used to specify fixed time interval for unrestricted use of prefix. When this time has been expired the address is considered as deprecated as specified in RFC4862 Preferred lifetime shall not be greater than the Valid Lifetime. All ones may be set for unlimited lifetime.
1.3.6.1.4.1.2544.1.12.37.1.28.1.6Unsigned32read-writecurrent
f3L3TrafficIPv6PrefixStorageType
OBJECT-TYPE
The storage type for this conceptual row.
1.3.6.1.4.1.2544.1.12.37.1.28.1.7StorageTyperead-createcurrent
f3L3TrafficIPv6PrefixRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3L3TrafficIPv6PrefixRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3L3TrafficIPv6PrefixRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3L3TrafficIPv6PrefixRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.37.1.28.1.8RowStatusread-createcurrent
f3L3TrafficIPv6NdpTable
OBJECT-TYPE
Traffic IPv6 NDP table.
1.3.6.1.4.1.2544.1.12.37.1.29not-accessiblecurrent
f3L3TrafficIPv6NdpEntry
OBJECT-TYPE
A conceptual row in f3L3TrafficIPv6NdpTable.
1.3.6.1.4.1.2544.1.12.37.1.29.1not-accessiblecurrent
f3L3TrafficIPv6NdpIPv6Addr
OBJECT-TYPE
This is the IP address of the NDP Entry.
1.3.6.1.4.1.2544.1.12.37.1.29.1.1Ipv6Addressnot-accessiblecurrent
f3L3TrafficIPv6NdpInterface
OBJECT-TYPE
This is the IP interface for the NDP Entry.
1.3.6.1.4.1.2544.1.12.37.1.29.1.2DisplayString (SIZE(0..15))read-createcurrent
f3L3TrafficIPv6NdpMacAddress
OBJECT-TYPE
This is the MAC address of the NDP Entry.
1.3.6.1.4.1.2544.1.12.37.1.29.1.3MacAddressread-createcurrent
f3L3TrafficIPv6NdpType
OBJECT-TYPE
The type of NDP Entry. Note that static entries can be created.
1.3.6.1.4.1.2544.1.12.37.1.29.1.4IpEntryTyperead-createcurrent
f3L3TrafficIPv6NdpReachabilityState
OBJECT-TYPE
This is the reachability state of the NDP Entry.
1.3.6.1.4.1.2544.1.12.37.1.29.1.5NdpNeighborReachabilityStateread-onlycurrent
f3L3TrafficIPv6NdpAge
OBJECT-TYPE
Indicates entry age in seconds.
1.3.6.1.4.1.2544.1.12.37.1.29.1.6Integer32read-onlycurrent
f3L3TrafficIPv6NdpStorageType
OBJECT-TYPE
The storage type for this conceptual row.
1.3.6.1.4.1.2544.1.12.37.1.29.1.7StorageTyperead-createcurrent
f3L3TrafficIPv6NdpRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3L3TrafficIPv6NdpRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3L3TrafficIPv6NdpRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3L3TrafficIPv6NdpRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.37.1.29.1.8RowStatusread-createcurrent
f3L3TrafficIpv6RouteTable
OBJECT-TYPE
A list of entries for the L3 Traffic Ipv6 route. Must set f3VrfActionX as optimizeIpv6RouteRetrieve(7) before get data from this table.
1.3.6.1.4.1.2544.1.12.37.1.30not-accessiblecurrent
f3L3TrafficIpv6RouteEntry
OBJECT-TYPE
A conceptual row in the f3L3TrafficIpv6RouteTable.
1.3.6.1.4.1.2544.1.12.37.1.30.1not-accessiblecurrent
f3L3TrafficIpv6RouteDest
OBJECT-TYPE
The destination IP address of this route. This object may not take a Multicast (Class D) address value. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical-AND of x with the value of the corresponding instance of the static-route-mask attribute is not equal to x.
1.3.6.1.4.1.2544.1.12.37.1.30.1.1Ipv6Addressnot-accessiblecurrent
f3L3TrafficIpv6RoutePrefixLength
OBJECT-TYPE
Indicate the mask to be logically ANDed with the destination address before being compared to the value in the cmStaticRouteDest field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the static route mask by reference to the IP Address Class. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical AND of x with the value of the corresponding instance of the static-route-dest attribute is not equal to static route destination.
1.3.6.1.4.1.2544.1.12.37.1.30.1.2Integer32not-accessiblecurrent
f3L3TrafficIpv6RouteGateway
OBJECT-TYPE
The address of the next router en route.
1.3.6.1.4.1.2544.1.12.37.1.30.1.3Ipv6Addressnot-accessiblecurrent
f3L3TrafficIpv6RouteInterface
OBJECT-TYPE
Name of the IP interface for the interface static route.
1.3.6.1.4.1.2544.1.12.37.1.30.1.4DisplayString (SIZE(0..15))not-accessiblecurrent
f3L3TrafficIpv6RouteMetric
OBJECT-TYPE
The primary routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's cmStaticRouteProto value. If this metric is not used, its value should be set to 1.
1.3.6.1.4.1.2544.1.12.37.1.30.1.5Integer32read-writecurrent
f3L3TrafficIpv6RouteType
OBJECT-TYPE
Indicates it is dynamic or static route.
1.3.6.1.4.1.2544.1.12.37.1.30.1.6IpEntryTyperead-createcurrent
f3L3TrafficIpv6RouteAdvertise
OBJECT-TYPE
Indicates whether this static route will be advertised via routing protocol.
1.3.6.1.4.1.2544.1.12.37.1.30.1.7TruthValueread-createcurrent
f3L3TrafficIpv6RouteStatus
OBJECT-TYPE
It specifies the traffic Ipv6 route status.
1.3.6.1.4.1.2544.1.12.37.1.30.1.8TrafficIpRouteStatusread-onlycurrent
f3L3TrafficIpv6RouteFlags
OBJECT-TYPE
It specifies the traffic Ipv6 route flags.
1.3.6.1.4.1.2544.1.12.37.1.30.1.9RouteFlagsread-onlycurrent
f3L3TrafficIpv6RouteOrigin
OBJECT-TYPE
The origin of IP Route.
1.3.6.1.4.1.2544.1.12.37.1.30.1.10TrafficIpRouteOriginTyperead-onlycurrent
f3L3TrafficIpv6RouteStorageType
OBJECT-TYPE
The storage type for this conceptual row.
1.3.6.1.4.1.2544.1.12.37.1.30.1.11StorageTyperead-createcurrent
f3L3TrafficIpv6RouteRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3L3TrafficIpv6RouteRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3L3TrafficIpv6RouteRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3L3TrafficIpv6RouteRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.37.1.30.1.12RowStatusread-createcurrent
f3DhcpV6RelayAgentTable
OBJECT-TYPE
A list of entries for the Dhcp V6 Relay Agent.
1.3.6.1.4.1.2544.1.12.37.1.31not-accessiblecurrent
f3DhcpV6RelayAgentEntry
OBJECT-TYPE
A conceptual row in the f3DhcpV6RelayAgentTable.
1.3.6.1.4.1.2544.1.12.37.1.31.1not-accessiblecurrent
f3DhcpV6RelayAgentIndex
OBJECT-TYPE
The integer index value describes the dhcp-relay-agent index.
1.3.6.1.4.1.2544.1.12.37.1.31.1.1Integer32not-accessiblecurrent
f3DhcpV6RelayAgentAlias
OBJECT-TYPE
The DHCP relay agent alias.
1.3.6.1.4.1.2544.1.12.37.1.31.1.2F3DisplayString (SIZE(0..256))read-writecurrent
f3DhcpV6RelayAgentAdminState
OBJECT-TYPE
This object represents the Administrative State of the agent.
1.3.6.1.4.1.2544.1.12.37.1.31.1.3AdminStateread-writecurrent
f3DhcpV6RelayAgentSecondaryState
OBJECT-TYPE
This object represents the Secondary State of the agent.
1.3.6.1.4.1.2544.1.12.37.1.31.1.4SecondaryStateread-onlycurrent
f3DhcpV6RelayAgentOperationalState
OBJECT-TYPE
This object represents the Operational State of the agent.
1.3.6.1.4.1.2544.1.12.37.1.31.1.5OperationalStateread-onlycurrent
f3DhcpV6RelayAgentServerIpAddress
OBJECT-TYPE
The Ipv6 address of this DCHP relay agent.
1.3.6.1.4.1.2544.1.12.37.1.31.1.6Ipv6Addressread-writecurrent
f3DhcpV6RelayAgentServerIpInteface
OBJECT-TYPE
This object describes the server Ip Interface.
1.3.6.1.4.1.2544.1.12.37.1.31.1.7VariablePointerread-writecurrent
f3DhcpV6RelayAgentStorageType
OBJECT-TYPE
The storage type for this conceptual row.
1.3.6.1.4.1.2544.1.12.37.1.31.1.8StorageTyperead-createcurrent
f3DhcpV6RelayAgentRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3DhcpV6RelayAgentRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3DhcpV6RelayAgentRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3DhcpV6RelayAgentRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.37.1.31.1.9RowStatusread-createcurrent
f3DhcpV6RelayAgentClientTrafficIpIfMemberTable
OBJECT-TYPE
A list of entries for the Dhcp V6 Relay Agent Client Traffic Ip Interface member.
1.3.6.1.4.1.2544.1.12.37.1.32not-accessiblecurrent
f3DhcpV6RelayAgentClientTrafficIpIfMemberEntry
OBJECT-TYPE
A conceptual row in the f3DhcpV6RelayAgentClientTrafficIpIfMemberTable.
1.3.6.1.4.1.2544.1.12.37.1.32.1not-accessiblecurrent
f3DhcpV6RelayAgentClientTrafficIpIfMemberObject
OBJECT-TYPE
This object describes the Client traffic ip interface.
1.3.6.1.4.1.2544.1.12.37.1.32.1.1VariablePointernot-accessiblecurrent
f3DhcpV6RelayAgentClientTrafficIpIfMemberStorageType
OBJECT-TYPE
The type of storage configured for this entry.
1.3.6.1.4.1.2544.1.12.37.1.32.1.2StorageTyperead-createcurrent
f3DhcpV6RelayAgentClientTrafficIpIfMemberRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3DhcpV6RelayAgentClientTrafficIpIfMemberRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3DhcpV6RelayAgentClientTrafficIpIfMemberRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3DhcpV6RelayAgentClientTrafficIpIfMemberRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.37.1.32.1.3RowStatusread-createcurrent
cmL3FlowPointTable
OBJECT-TYPE
A list of entries for the L3 flowpoint.
1.3.6.1.4.1.2544.1.12.37.1.33not-accessiblecurrent
cmL3FlowPointEntry
OBJECT-TYPE
A conceptual row in the cmL3FlowPointTable.
1.3.6.1.4.1.2544.1.12.37.1.33.1not-accessiblecurrent
cmL3FlowPointPortIndex
OBJECT-TYPE
The port number value.
1.3.6.1.4.1.2544.1.12.37.1.33.1.1Integer32not-accessiblecurrent
cmL3FlowPointIndex
OBJECT-TYPE
The L3 flow point number.
1.3.6.1.4.1.2544.1.12.37.1.33.1.2Integer32not-accessiblecurrent
cmL3FlowPointAlias
OBJECT-TYPE
This object describes the L3 flow point alias.
1.3.6.1.4.1.2544.1.12.37.1.33.1.3F3DisplayString (SIZE(0..256))read-writecurrent
cmL3FlowPointAdminState
OBJECT-TYPE
This object describes the L3 flow point admin state.
1.3.6.1.4.1.2544.1.12.37.1.33.1.4AdminStateread-writecurrent
cmL3FlowPointSecondaryState
OBJECT-TYPE
This object describes the L3 flow point secondary state.
1.3.6.1.4.1.2544.1.12.37.1.33.1.5SecondaryStateread-onlycurrent
cmL3FlowPointOperationalState
OBJECT-TYPE
This object describes the L3 flow point operational state.
1.3.6.1.4.1.2544.1.12.37.1.33.1.6OperationalStateread-onlycurrent
cmL3FlowPointMultiCOSEnabled
OBJECT-TYPE
Control to enable or disable per-COS BWPs on a FlowPoint. ENABLED:per-COS BWPs (CIR, EIR, CBS, EBS, CM, CF) are applied as a policing function for all ingress frames of this flowpoint. DISABLED:per-Flow BWP (CIR, EIR, CBS, EBS, CM, CF) is applied as a policing function for all ingress frames of this flowpoint. User must independently enable each COS BWP when ENABLED.
1.3.6.1.4.1.2544.1.12.37.1.33.1.7TruthValueread-writecurrent
cmL3FlowPointCOS
OBJECT-TYPE
Identifies the internal COS applied to all ingress frames of the flowpoint.
1.3.6.1.4.1.2544.1.12.37.1.33.1.8Integer32read-writecurrent
cmL3FlowPointUntaggedMemberShipEnabled
OBJECT-TYPE
This attribute controls untagged frames membership for the Flowpoint. ENABLED: Ingress untagged frame matches Flowpoint membership. DISABLED: Ingress untagged frame does not match Flowpoint membership.
1.3.6.1.4.1.2544.1.12.37.1.33.1.9TruthValueread-writecurrent
cmL3FlowPointOuterTagMemberShipEnabled
OBJECT-TYPE
This attribute controls outer tag membership for the Flowpoint whether enabled.
1.3.6.1.4.1.2544.1.12.37.1.33.1.10TruthValueread-writecurrent
cmL3FlowPointOuterTagMemberShipVlanId
OBJECT-TYPE
This attribute controls outer tag VlanId membership for the Flowpoint.
1.3.6.1.4.1.2544.1.12.37.1.33.1.11VlanIdread-writecurrent
cmL3FlowPointInnerTagMemberShipEnabled
OBJECT-TYPE
This attribute controls inner tag membership for the Flowpoint whether enabled.
1.3.6.1.4.1.2544.1.12.37.1.33.1.12TruthValueread-writecurrent
cmL3FlowPointInnerTagMemberShipVlanId
OBJECT-TYPE
This attribute controls inner tag VlanId membership for the Flowpoint.
1.3.6.1.4.1.2544.1.12.37.1.33.1.13VlanIdread-writecurrent
cmL3FlowPointFragmentedPktsFwdEnabled
OBJECT-TYPE
This attribute specifies whether received IP Packets with More Fragments flag should be forwarded by the FlowPoint.
1.3.6.1.4.1.2544.1.12.37.1.33.1.14TruthValueread-writecurrent
cmL3FlowPointHCosMgmtEnabled
OBJECT-TYPE
This attribute specifies whether the Hierarchical COS shaping enabled for this flow point.
1.3.6.1.4.1.2544.1.12.37.1.33.1.15TruthValueread-writecurrent
cmL3FlowPointHCosGuaranteedBwHi
OBJECT-TYPE
This attribute specifies the Hierarchical COS guarranteed bandwidth high 32 bits for this flow point.
1.3.6.1.4.1.2544.1.12.37.1.33.1.16Unsigned32read-writecurrent
cmL3FlowPointHCosGuaranteedBwLo
OBJECT-TYPE
This attribute specifies the Hierarchical COS guarranteed bandwidth low 32 bits for this flow point.
1.3.6.1.4.1.2544.1.12.37.1.33.1.17Unsigned32read-writecurrent
cmL3FlowPointHCosMaximumBwHi
OBJECT-TYPE
This attribute specifies the Hierarchical COS maximum bandwidth high 32 bits for this flow point.
1.3.6.1.4.1.2544.1.12.37.1.33.1.18Unsigned32read-writecurrent
cmL3FlowPointHCosMaximumBwLo
OBJECT-TYPE
This attribute specifies the Hierarchical COS maximum bandwidth low 32 bits for this flow point.
1.3.6.1.4.1.2544.1.12.37.1.33.1.19Unsigned32read-writecurrent
cmL3FlowPointDscpOverwriteControl
OBJECT-TYPE
This attribute allows enable dscp value overwrite.
1.3.6.1.4.1.2544.1.12.37.1.33.1.20TruthValueread-writecurrent
cmL3FlowPointPriMapProfile
OBJECT-TYPE
This attribute allows specify the priority map profile.
1.3.6.1.4.1.2544.1.12.37.1.33.1.21VariablePointerread-writecurrent
cmL3FlowPointStorageType
OBJECT-TYPE
The type of storage configured for this entry.
1.3.6.1.4.1.2544.1.12.37.1.33.1.22StorageTyperead-createcurrent
cmL3FlowPointRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of cmL3FlowPointRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with cmL3FlowPointRowStatus value as createAndGo(4). Upon successful row creation, this variable has a value of active(1). The cmL3FlowPointRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.37.1.33.1.23RowStatusread-createcurrent
cmL3FlowPointAclNoMatchDisposition
OBJECT-TYPE
This attribute allows specify ACL no match disposition type
1.3.6.1.4.1.2544.1.12.37.1.33.1.24AclNoMatchDispositionTyperead-writecurrent
cmL3FlowPointWfqSegmentationCOS
OBJECT-TYPE
This object is used to specify wfq segmentation COS value.
1.3.6.1.4.1.2544.1.12.37.1.33.1.25Integer32read-writecurrent
cmL3FlowPointWfqGroupCOS
OBJECT-TYPE
This object is used to specify wfq group COS value.
1.3.6.1.4.1.2544.1.12.37.1.33.1.26Integer32read-writecurrent
cmL3FlowPointWfqGroupEirLo
OBJECT-TYPE
This object is used to specify wfq group EIR low 32 bits value.
1.3.6.1.4.1.2544.1.12.37.1.33.1.27Unsigned32read-writecurrent
cmL3FlowPointWfqGroupEirHi
OBJECT-TYPE
This object is used to specify wfq group EIR high 32 bits value.
1.3.6.1.4.1.2544.1.12.37.1.33.1.28Unsigned32read-writecurrent
cmL3FlowPointEgressShapingType
OBJECT-TYPE
This object allows specification of Shaping Type for Flow Point
1.3.6.1.4.1.2544.1.12.37.1.33.1.29ShapingTyperead-writecurrent
cmL3QosPolicerTable
OBJECT-TYPE
A list of entries corresponding to Ethernet Quality of Service Policer for configuration purposes.
1.3.6.1.4.1.2544.1.12.37.1.34not-accessiblecurrent
cmL3QosPolicerEntry
OBJECT-TYPE
A conceptual row in the cmL3QosPolicerTable. These entries represent a Quality of Service Policer.
1.3.6.1.4.1.2544.1.12.37.1.34.1not-accessiblecurrent
cmL3QosPolicerIndex
OBJECT-TYPE
The Policer Index that represents the COS level. This is applicable in case of a Multi COS flow. Index 1 represents COS 0; Index 2 represents COS 1 and so on. In release 5.6CC the range is extended to 1..16 to support duplicate N2A policers on a Flow. The duplicate policers are created under a Flow if network interface of the Flow is ERP Group or Split Horizon Group. In case of multi-cos Flow indices 1..8 represent policers of COS 0..7 going from Network 1 port; indices 9..16 represent policers for COS 0..7 going from Network 2 port. In case of single-cos Flow index 1 represents policer going from Network 1 port; index 9 represents policer going from Network 2 port.
1.3.6.1.4.1.2544.1.12.37.1.34.1.1Integer32 (1..16)read-createcurrent
cmL3QosPolicerAdminState
OBJECT-TYPE
This object represents the Administrative State of the QOS Flow Policer.
1.3.6.1.4.1.2544.1.12.37.1.34.1.2AdminStateread-writecurrent
cmL3QosPolicerOperationalState
OBJECT-TYPE
This object represents the Operational State of the QOS Flow Policer.
1.3.6.1.4.1.2544.1.12.37.1.34.1.3OperationalStateread-onlycurrent
cmL3QosPolicerSecondaryState
OBJECT-TYPE
This object represents the Secondary State of the QOS Flow Policer.
1.3.6.1.4.1.2544.1.12.37.1.34.1.4SecondaryStateread-onlycurrent
cmL3QosPolicerCIRLo
OBJECT-TYPE
This object allows specification of the Commited Information Rate(CIR) on Policer. This represents the lower 32 bits of the CIR.
1.3.6.1.4.1.2544.1.12.37.1.34.1.5Unsigned32read-createcurrent
cmL3QosPolicerCIRHi
OBJECT-TYPE
This object allows specification of the Commited Information Rate(CIR) on Policer. This represents the upper 32 bits of the CIR.
1.3.6.1.4.1.2544.1.12.37.1.34.1.6Unsigned32read-createcurrent
cmL3QosPolicerEIRLo
OBJECT-TYPE
This object allows specification of the Excess Information Rate(EIR) on the Policer. This represents the lower 32 bits of the EIR.
1.3.6.1.4.1.2544.1.12.37.1.34.1.7Unsigned32read-createcurrent
cmL3QosPolicerEIRHi
OBJECT-TYPE
This object allows specification of the Excess Information Rate(EIR) on the Policer. This represents the upper 32 bits of the EIR.
1.3.6.1.4.1.2544.1.12.37.1.34.1.8Unsigned32read-createcurrent
cmL3QosPolicerCBS
OBJECT-TYPE
This object allows specification of the Commited Burst Size (CBS) on Policer.
1.3.6.1.4.1.2544.1.12.37.1.34.1.9Integer32read-createcurrent
cmL3QosPolicerEBS
OBJECT-TYPE
This object allows specification of the Excess Burst Size (EBS) on the Policer.
1.3.6.1.4.1.2544.1.12.37.1.34.1.10Integer32read-createcurrent
cmL3QosPolicerAlgorithm
OBJECT-TYPE
This object allows specification of Policer algorithm as 'srTCM' (Single Rate Triple Color Marking) or 'trTCM' (Two Rate Triple Color Marking).
1.3.6.1.4.1.2544.1.12.37.1.34.1.11PolicerAlgorithmTyperead-onlycurrent
cmL3QosPolicerColorMode
OBJECT-TYPE
This object allows specification of Policer Color Mode as 'color-aware' or 'color-blind'.
1.3.6.1.4.1.2544.1.12.37.1.34.1.12PolicerColorModeread-createcurrent
cmL3QosPolicerCouplingFlag
OBJECT-TYPE
This object allows specification of Policer Coupling Flag. When coupling is enabled, tokens that would normally be added to the C-bucket are passed to the E-bucket only once the CIR bucket has reached its CBS level. Therefore under this condition the E-bucket is being filled at the rate of CIR + EIR. Normally the long term average of frames declared yellow is bounded by the EIR. Coupling is a function to allow the long term average of frames declared yellow to be bounded by CIR + EIR. This allows a higher volume of yellow frames to be delivered/received if the arrival of green marked frames is low. Tokens from the E-bucket do NOT get passed to the C-bucket once the EBS level has been reached. Enabling coupling in combination with a provisioned EIR of 0 allows for a single rate three color marking (srTCM) algorithm to be established. In this situation the E-bucket is filled at the CIR rate in the case the C-bucket is filled to its CBS level.
1.3.6.1.4.1.2544.1.12.37.1.34.1.13TruthValueread-createcurrent
cmL3QosPolicerCIRMaxHi
OBJECT-TYPE
This object allows specification of the Commited Information Rate(CIR) MAX on Policer. This represents the high 32 bits.
1.3.6.1.4.1.2544.1.12.37.1.34.1.14Unsigned32read-writecurrent
cmL3QosPolicerCIRMaxLo
OBJECT-TYPE
This object allows specification of the Commited Information Rate(CIR) MAX on Policer. This represents the lower 32 bits.
1.3.6.1.4.1.2544.1.12.37.1.34.1.15Unsigned32read-writecurrent
cmL3QosPolicerEIRMaxHi
OBJECT-TYPE
This object allows specification of the Excess Information Rate(EIR) MAX on the Policer. This represents the high 32 bits.
1.3.6.1.4.1.2544.1.12.37.1.34.1.16Unsigned32read-writecurrent
cmL3QosPolicerEIRMaxLo
OBJECT-TYPE
This object allows specification of the Excess Information Rate(EIR) MAX on the Policer. This represents the lower 32 bits.
1.3.6.1.4.1.2544.1.12.37.1.34.1.17Unsigned32read-writecurrent
cmL3QosPolicerEnvelopeObject
OBJECT-TYPE
This object allows specification of envelope object.
1.3.6.1.4.1.2544.1.12.37.1.34.1.18VariablePointerread-writecurrent
cmL3QosPolicerRank
OBJECT-TYPE
This object allows specification of rank value.
1.3.6.1.4.1.2544.1.12.37.1.34.1.19Integer32read-writecurrent
cmL3QosPolicerPolicingEnabled
OBJECT-TYPE
This attribute allows enable or disable policers.
1.3.6.1.4.1.2544.1.12.37.1.34.1.20TruthValueread-writecurrent
cmL3QosPolicerStorageType
OBJECT-TYPE
The type of storage configured for this entry.
1.3.6.1.4.1.2544.1.12.37.1.34.1.21StorageTyperead-createcurrent
cmL3QosPolicerRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of cmL3QosPolicerRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with cmL3QosPolicerRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The cmL3QosPolicerRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.37.1.34.1.22RowStatusread-createcurrent
cmL3QosShaperTable
OBJECT-TYPE
A list of entries corresponding to Ethernet Access Port Quality of Service Shaper for configuration purposes. These shapers can be managed when the Access Port is in evpl mode and are relevant for traffic in the network to access direction.
1.3.6.1.4.1.2544.1.12.37.1.35not-accessiblecurrent
cmL3QosShaperEntry
OBJECT-TYPE
A conceptual row in the cmL3QosShaperTable. These entries represent a Quality of Service Shaper.
1.3.6.1.4.1.2544.1.12.37.1.35.1not-accessiblecurrent
cmL3QosShaperIndex
OBJECT-TYPE
The unique integer index value corresponding to a Quality of Service Shaper.
1.3.6.1.4.1.2544.1.12.37.1.35.1.1Integer32 (1..8)read-createcurrent
cmL3QosShaperAdminState
OBJECT-TYPE
This object represents the Administrative State of the QOS Shaper.
1.3.6.1.4.1.2544.1.12.37.1.35.1.2AdminStateread-writecurrent
cmL3QosShaperOperationalState
OBJECT-TYPE
This object represents the Operational State of the QOS Shaper.
1.3.6.1.4.1.2544.1.12.37.1.35.1.3OperationalStateread-onlycurrent
cmL3QosShaperSecondaryState
OBJECT-TYPE
This object represents the Secondary State of the QOS Shaper.
1.3.6.1.4.1.2544.1.12.37.1.35.1.4SecondaryStateread-onlycurrent
cmL3QosShaperCIRLo
OBJECT-TYPE
This object represents the Commited Information Rate(CIR) (Lower 32 bits)of a Shaper.
1.3.6.1.4.1.2544.1.12.37.1.35.1.5Unsigned32read-createcurrent
cmL3QosShaperCIRHi
OBJECT-TYPE
This object represents the Commited Information Rate(CIR) (Higher 32 bits) of a Shaper.
1.3.6.1.4.1.2544.1.12.37.1.35.1.6Unsigned32read-createcurrent
cmL3QosShaperEIRLo
OBJECT-TYPE
This object represents the Excess Information Rate(EIR) (Higher 32 bits) on the Shaper.
1.3.6.1.4.1.2544.1.12.37.1.35.1.7Unsigned32read-createcurrent
cmL3QosShaperEIRHi
OBJECT-TYPE
This object represents the Excess Information Rate(EIR) (Higher 32 bits) on the Shaper.
1.3.6.1.4.1.2544.1.12.37.1.35.1.8Unsigned32read-createcurrent
cmL3QosShaperBufferSize
OBJECT-TYPE
This object represents the Buffer Size of the Shaper.
1.3.6.1.4.1.2544.1.12.37.1.35.1.9Unsigned32read-createcurrent
cmL3QosShaperCOS
OBJECT-TYPE
This object provides the COS (Class of Service) value for the QOS Shaper.
1.3.6.1.4.1.2544.1.12.37.1.35.1.10Integer32 (0..7)read-onlycurrent
cmL3QosShaperStorageType
OBJECT-TYPE
The type of storage configured for this entry.
1.3.6.1.4.1.2544.1.12.37.1.35.1.11StorageTyperead-createcurrent
cmL3QosShaperRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of cmL3QosShaperRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with cmL3QosShaperRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The cmL3QosShaperRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.37.1.35.1.12RowStatusread-createcurrent
cmL3QosShaperWfqWeight
OBJECT-TYPE
This object represents the wfq weight of the QoS Shaper.
1.3.6.1.4.1.2544.1.12.37.1.35.1.13Integer32read-writecurrent
f3L3TrafficOspfInterfaceTable
OBJECT-TYPE
A list of entries for the Traffic OSPF Interface.
1.3.6.1.4.1.2544.1.12.37.1.36not-accessiblecurrent
f3L3TrafficOspfInterfaceEntry
OBJECT-TYPE
A conceptual row in the f3L3TrafficOspfInterfaceTable.
1.3.6.1.4.1.2544.1.12.37.1.36.1not-accessiblecurrent
f3L3TrafficOspfInterfaceIndex
OBJECT-TYPE
The index of the Traffic OSPF Interface entry.
1.3.6.1.4.1.2544.1.12.37.1.36.1.1Integer32not-accessiblecurrent
f3L3TrafficOspfInterfaceOspfCost
OBJECT-TYPE
The cost of the route during the SPF calculation.
1.3.6.1.4.1.2544.1.12.37.1.36.1.2Unsigned32read-writecurrent
f3L3TrafficOspfInterfaceType
OBJECT-TYPE
Interface network type.
1.3.6.1.4.1.2544.1.12.37.1.36.1.3OspfIfTyperead-writecurrent
f3L3TrafficOspfInterfaceOspfRtrPriority
OBJECT-TYPE
An 8-bit unsigned integer, used for DR and BDR election, may be default. 0 means not to attend DR election.
1.3.6.1.4.1.2544.1.12.37.1.36.1.4Integer32read-writecurrent
f3L3TrafficOspfInterfaceOspfHelloInterval
OBJECT-TYPE
The interval in seconds between Hello Packets that the router sends on the interface.
1.3.6.1.4.1.2544.1.12.37.1.36.1.5Integer32read-writecurrent
f3L3TrafficOspfInterfaceOspfDeadInterval
OBJECT-TYPE
The number of seconds before the router's neighbors will declare it down, when they stop hearing the router's Hello Packets.
1.3.6.1.4.1.2544.1.12.37.1.36.1.6Integer32read-writecurrent
f3L3TrafficOspfInterfaceOspfTransmitDelay
OBJECT-TYPE
The estimated number of seconds it takes to transmit a Link State Update Packet over this interface. LSAs contained in the Link State update packet will have their age incremented by this amount before transmission. This value should take into account transmission and propagation delays; it must be greater than zero.
1.3.6.1.4.1.2544.1.12.37.1.36.1.7Integer32read-writecurrent
f3L3TrafficOspfInterfaceOspfRetransmitInterval
OBJECT-TYPE
The number of seconds between LSA retransmissions, for adjacencies belonging to this interface. Also used when retransmitting Database Description and Link State Request Packets.
1.3.6.1.4.1.2544.1.12.37.1.36.1.8Integer32read-writecurrent
f3L3TrafficOspfInterfaceState
OBJECT-TYPE
The State of Interface in running OSPF protocol.
1.3.6.1.4.1.2544.1.12.37.1.36.1.9OspfInterfaceStateread-onlycurrent
f3L3TrafficOspfInterfaceOspfDesignatedRouterId
OBJECT-TYPE
Designated Router IP interface on the Network.
1.3.6.1.4.1.2544.1.12.37.1.36.1.10IpAddressread-onlycurrent
f3L3TrafficOspfInterfaceOspfBackupDesignatedRouterId
OBJECT-TYPE
Backup Designated Router IP interface on the Network.
1.3.6.1.4.1.2544.1.12.37.1.36.1.11IpAddressread-onlycurrent
f3L3TrafficOspfInterfaceOspfAuthType
OBJECT-TYPE
This attribute is used to specify authentication type. Simple: 64-bits clear password inserted into ospf packets header. None: No authentication is used. Cryptographic: a shared secret which enables the generation/verification of message digests which are appended to the OSPF protocol packets. IPsec: use IP layer's IPSec to support authentication, rather than OSPF header..
1.3.6.1.4.1.2544.1.12.37.1.36.1.12OspfAuthTyperead-writecurrent
f3L3TrafficOspfInterfaceOspfSimpleAuthKey
OBJECT-TYPE
Simple Authentication type authentication key (8 Bytes length).
1.3.6.1.4.1.2544.1.12.37.1.36.1.13DisplayStringread-writecurrent
f3L3TrafficOspfInterfaceOspfCryptoKeyId
OBJECT-TYPE
Key id from the keys configured in the Authentication keys table. This key is used if Authentication Type is cryptographic.
1.3.6.1.4.1.2544.1.12.37.1.36.1.14VariablePointerread-writecurrent
f3L3TrafficOspfInterfaceOspfInstanceId
OBJECT-TYPE
OSPFv3 Instance ID. Instance ID allows multiple OSPF protocol instances to be run on a single link. Default value is 0. It is only necessary to assign a value other than 0 on those links that will contain multiple separate communities of OSPF routers. Only Applicable to ospfv3.
1.3.6.1.4.1.2544.1.12.37.1.36.1.15Unsigned32read-writecurrent
f3L3TrafficOspfInterfaceId
OBJECT-TYPE
32-bit number uniquely identifying this interface among the collection of this router's interfaces. Shall be unique per router. Default vlaue shall be the last number of EID. Only applicable to OSPFv3.
1.3.6.1.4.1.2544.1.12.37.1.36.1.16Unsigned32read-writecurrent
f3L3TrafficOspfInterfaceLinkLsaSuppression
OBJECT-TYPE
Indicates whether or not origination of a link-LSA is suppressed. In OSPFv3, link LSAs are generated for each link, announcing link-local IPv6 address of the router to its local neighbors. These are useless on PtP or PtMP networks and this option allows to suppress the link LSA origination for such interfaces. The attribute is ignored on other than PtP or PtMP interfaces. Default value is disbaled. Only applicable to OSPFv3.
1.3.6.1.4.1.2544.1.12.37.1.36.1.17TruthValueread-writecurrent
f3L3TrafficOspfInterfacePassiveControl
OBJECT-TYPE
Enable/Disable passive interface - a passive interface's prefix will be advertised but no neighbor adjacencies will be formed on the interface..
1.3.6.1.4.1.2544.1.12.37.1.36.1.18TruthValueread-writecurrent
f3L3TrafficOspfInterfaceAssociatedIpInterface
OBJECT-TYPE
The reference of Traffic IP Interface or loopback interface. It is the name of interface.
1.3.6.1.4.1.2544.1.12.37.1.36.1.19DisplayStringread-createcurrent
f3L3TrafficOspfInterfaceStorageType
OBJECT-TYPE
The type of storage configured for this entry.
1.3.6.1.4.1.2544.1.12.37.1.36.1.20StorageTyperead-createcurrent
f3L3TrafficOspfInterfaceRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3L3TrafficOspfInterfaceRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3L3TrafficOspfInterfaceRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3L3TrafficOspfInterfaceRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.37.1.36.1.21RowStatusread-createcurrent
f3L3TrafficOspfInterfaceTilfaControl
OBJECT-TYPE
TI-LFA Control.
1.3.6.1.4.1.2544.1.12.37.1.36.1.22TruthValueread-createcurrent
f3L3TrafficOspfInterfaceTilfaProtectionType
OBJECT-TYPE
TI-LFA Protection Type.
1.3.6.1.4.1.2544.1.12.37.1.36.1.23TilfaProtectionTyperead-createcurrent
f3L3TrafficBgpPeerAddressFamilyTable
OBJECT-TYPE
A list of entries for the Traffic BGP Peer Address Family.
1.3.6.1.4.1.2544.1.12.37.1.37not-accessiblecurrent
f3L3TrafficBgpPeerAddressFamilyEntry
OBJECT-TYPE
A conceptual row in the f3L3TrafficBgpPeerAddressFamilyTable.
1.3.6.1.4.1.2544.1.12.37.1.37.1not-accessiblecurrent
f3L3TrafficBgpPeerAddressFamilyIndex
OBJECT-TYPE
The index of the Traffic BGP Peer Address Family entry.
1.3.6.1.4.1.2544.1.12.37.1.37.1.1Integer32not-accessiblecurrent
f3L3TrafficBgpPeerAddressFamilyName
OBJECT-TYPE
Address Family Name.
1.3.6.1.4.1.2544.1.12.37.1.37.1.2BgpPeerAddressFamilyNameTyperead-createcurrent
f3L3TrafficBgpPeerAddressFamilyRedistOspfRoute
OBJECT-TYPE
If set to true, redistribute the connected route to the neighbour.
1.3.6.1.4.1.2544.1.12.37.1.37.1.3TruthValueread-writecurrent
f3L3TrafficBgpPeerAddressFamilyRedistConnectedRoute
OBJECT-TYPE
If set to true, redistribute the connected route to the neighbour.
1.3.6.1.4.1.2544.1.12.37.1.37.1.4TruthValueread-writecurrent
f3L3TrafficBgpPeerAddressFamilyRedistStaticRoute
OBJECT-TYPE
If set to true, redistribute the static route to the neighbour.
1.3.6.1.4.1.2544.1.12.37.1.37.1.5TruthValueread-writecurrent
f3L3TrafficBgpPeerAddressFamilyRedistDhcpRoute
OBJECT-TYPE
If set to true, redistribute the dhcproute to the neighbour.
1.3.6.1.4.1.2544.1.12.37.1.37.1.6TruthValueread-writecurrent
f3L3TrafficBgpPeerAddressFamilyRedistSlaacRoute
OBJECT-TYPE
If set to true, redistribute the default route to the neighbour. This attribute is only applicable to IPv6 address family.
1.3.6.1.4.1.2544.1.12.37.1.37.1.7TruthValueread-writecurrent
f3L3TrafficBgpPeerAddressFamilySendDefaultRoute
OBJECT-TYPE
If set to true, send the default route to the neighbour.
1.3.6.1.4.1.2544.1.12.37.1.37.1.8TruthValueread-writecurrent
f3L3TrafficBgpPeerAddressFamilyNextHopType
OBJECT-TYPE
The mechanism to update NEXT HOP attribute in update message: 1. DEFAULT: Update next hop according the rules in RFC4271 2. SELF: Use transmitting interface's as the next hop 3. IPv4 Address: Configure IPv4 address as next hop explicitly 4. IPv6 Address: Configure IPv6 address as next hop explicitly
1.3.6.1.4.1.2544.1.12.37.1.37.1.9BgpNextHopUpdateTyperead-writecurrent
f3L3TrafficBgpPeerAddressFamilyNextHopIpv4
OBJECT-TYPE
The IPv4 address used to override NEXT HOP attribute.
1.3.6.1.4.1.2544.1.12.37.1.37.1.10IpAddressread-writecurrent
f3L3TrafficBgpPeerAddressFamilyNextHopIpv6
OBJECT-TYPE
The IPv4 address used to override NEXT HOP attribute.
1.3.6.1.4.1.2544.1.12.37.1.37.1.11Ipv6Addressread-writecurrent
f3L3TrafficBgpPeerAddressFamilyExtNextHopControl
OBJECT-TYPE
Whether to support Extended Next Hop Encoding Capability. E.g Allowing advertising IPV4 route with a Next Hop address of IPv6..
1.3.6.1.4.1.2544.1.12.37.1.37.1.12TruthValueread-writecurrent
f3L3TrafficBgpPeerAddressFamilyStorageType
OBJECT-TYPE
The type of storage configured for this entry.
1.3.6.1.4.1.2544.1.12.37.1.37.1.13StorageTyperead-createcurrent
f3L3TrafficBgpPeerAddressFamilyRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3L3TrafficBgpPeerAddressFamilyRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3L3TrafficBgpPeerAddressFamilyRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3L3TrafficBgpPeerAddressFamilyRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.37.1.37.1.14RowStatusread-createcurrent
f3L3TrafficBgpRIBRouteTable
OBJECT-TYPE
A list of entries for the Traffic BGP RIB routes.
1.3.6.1.4.1.2544.1.12.37.1.38not-accessiblecurrent
f3L3TrafficBgpRIBRouteEntry
OBJECT-TYPE
A conceptual row in the f3L3TrafficBgpRouteTable.
1.3.6.1.4.1.2544.1.12.37.1.38.1not-accessiblecurrent
f3L3TrafficBgpRIBRouteIndex
OBJECT-TYPE
The index of the Traffic BGP RIB Route entry.
1.3.6.1.4.1.2544.1.12.37.1.38.1.1Integer32not-accessiblecurrent
f3L3TrafficBgpRIBRouteNetwork
OBJECT-TYPE
Traffic BGP RIB Route's destination network address.
1.3.6.1.4.1.2544.1.12.37.1.38.1.2DisplayStringread-onlycurrent
f3L3TrafficBgpRIBRouteNextHop
OBJECT-TYPE
Traffic BGP RIB Route's next hop interface address.
1.3.6.1.4.1.2544.1.12.37.1.38.1.3DisplayStringread-onlycurrent
f3L3TrafficBgpRIBRouteMetric
OBJECT-TYPE
List of AS numbers in the path to route's destination network
1.3.6.1.4.1.2544.1.12.37.1.38.1.4Integer32read-onlycurrent
f3L3TrafficBgpRIBRoutePath
OBJECT-TYPE
The index of the Traffic BGP RIB Route entry.
1.3.6.1.4.1.2544.1.12.37.1.38.1.5DisplayStringread-onlycurrent
f3L3TrafficBgpInRouteTable
OBJECT-TYPE
BGP In routes. Must set f3L3TrafficBgpRouterAction as optimizeBgpInRouteRetrieve(2) before get data from this table.
1.3.6.1.4.1.2544.1.12.37.1.39not-accessiblecurrent
f3L3TrafficBgpInRouteEntry
OBJECT-TYPE
A conceptual row in the f3L3TrafficBgpInRouteTable. Entries can be created/deleted in this table by management application action.
1.3.6.1.4.1.2544.1.12.37.1.39.1not-accessiblecurrent
f3L3TrafficBgpInRouteIndex
OBJECT-TYPE
Index of this route. Key of the table.
1.3.6.1.4.1.2544.1.12.37.1.39.1.1Unsigned32not-accessiblecurrent
f3L3TrafficBgpInRouteNetwork
OBJECT-TYPE
Network of destination.
1.3.6.1.4.1.2544.1.12.37.1.39.1.2DisplayString (SIZE(0..64))read-onlycurrent
f3L3TrafficBgpInRouteNextHop
OBJECT-TYPE
Address of next hop.
1.3.6.1.4.1.2544.1.12.37.1.39.1.3DisplayString (SIZE(0..64))read-onlycurrent
f3L3TrafficBgpInRouteMetric
OBJECT-TYPE
Metric value of this route.
1.3.6.1.4.1.2544.1.12.37.1.39.1.4Unsigned32read-onlycurrent
f3L3TrafficBgpInRoutePath
OBJECT-TYPE
The list of AS numbers to the destination.
1.3.6.1.4.1.2544.1.12.37.1.39.1.5DisplayString (SIZE(0..1024))read-onlycurrent
f3L3TrafficBgpInRouteLocalPreference
OBJECT-TYPE
Local Preference Value received from iBGP.
1.3.6.1.4.1.2544.1.12.37.1.39.1.6Unsigned32read-onlycurrent
f3L3TrafficBgpRouteV2Table
OBJECT-TYPE
BGP routes. Must set f3L3TrafficBgpRouterAction as optimizeBgpRouteRetrieve(1) before get data from this table.
1.3.6.1.4.1.2544.1.12.37.1.40not-accessiblecurrent
f3L3TrafficBgpRouteV2Entry
OBJECT-TYPE
A conceptual row in the f3L3TrafficBgpRouteV2Table. Entries can be created/deleted in this table by management application action.
1.3.6.1.4.1.2544.1.12.37.1.40.1not-accessiblecurrent
f3L3TrafficBgpRouteV2Index
OBJECT-TYPE
Index of this route. Key of the table.
1.3.6.1.4.1.2544.1.12.37.1.40.1.1Unsigned32not-accessiblecurrent
f3L3TrafficBgpRouteV2Network
OBJECT-TYPE
Network of destination.
1.3.6.1.4.1.2544.1.12.37.1.40.1.2DisplayString (SIZE(0..64))read-onlycurrent
f3L3TrafficBgpRouteV2NextHop
OBJECT-TYPE
Address of next hop.
1.3.6.1.4.1.2544.1.12.37.1.40.1.3DisplayString (SIZE(0..64))read-onlycurrent
f3L3TrafficBgpRouteV2Metric
OBJECT-TYPE
Metric value of this route.
1.3.6.1.4.1.2544.1.12.37.1.40.1.4Unsigned32read-onlycurrent
f3L3TrafficBgpRouteV2Path
OBJECT-TYPE
The list of AS numbers to the destination.
1.3.6.1.4.1.2544.1.12.37.1.40.1.5DisplayString (SIZE(0..1024))read-onlycurrent
f3L3TrafficBgpRouteV2LocalPreference
OBJECT-TYPE
Local Preference Value received from iBGP.
1.3.6.1.4.1.2544.1.12.37.1.40.1.6Unsigned32read-onlycurrent
f3L3TrafficBgpPeerAddressFamilyAdvPrefixTable
OBJECT-TYPE
Advertising Prefix of BGP Peer Address Family.
1.3.6.1.4.1.2544.1.12.37.1.41not-accessiblecurrent
f3L3TrafficBgpPeerAddressFamilyAdvPrefixEntry
OBJECT-TYPE
A conceptual row in the f3L3TrafficBgpPeerAddressFamilyAdvPrefixTable. Entries can be created/deleted in this table by management application action.
1.3.6.1.4.1.2544.1.12.37.1.41.1not-accessiblecurrent
f3L3TrafficBgpPeerAddressFamilyAdvPrefix
OBJECT-TYPE
Advertising Prefix of a BGP Peer Address Family. Key of the table.
1.3.6.1.4.1.2544.1.12.37.1.41.1.1DisplayStringnot-accessiblecurrent
f3L3TrafficBgpPeerAddressFamilyAdvPrefixStorageType
OBJECT-TYPE
The storage type for this conceptual row.
1.3.6.1.4.1.2544.1.12.37.1.41.1.2StorageTyperead-createcurrent
f3L3TrafficBgpPeerAddressFamilyAdvPrefixRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3L3TrafficBgpPeerAddressFamilyAdvPrefixRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3L3TrafficBgpPeerAddressFamilyAdvPrefixRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3L3TrafficBgpPeerAddressFamilyAdvPrefixRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.37.1.41.1.3RowStatusread-createcurrent
f3L3TrafficOspfV3NeighborTable
OBJECT-TYPE
OSPF v3 neighbor table. Must set f3VrfOspfRouterAction as optimizeOspfNeighborRetrieve(3) before get data from this table.
1.3.6.1.4.1.2544.1.12.37.1.42not-accessiblecurrent
f3L3TrafficOspfV3NeighborEntry
OBJECT-TYPE
A conceptual row in the f3L3TrafficOspfV3NeighborTable. Entries can be created/deleted in this table by management application action.
1.3.6.1.4.1.2544.1.12.37.1.42.1not-accessiblecurrent
f3L3TrafficOspfV3NeighborRouterId
OBJECT-TYPE
Router ID of the neighbor.
1.3.6.1.4.1.2544.1.12.37.1.42.1.1IpAddressread-onlycurrent
f3L3TrafficOspfV3NeighborInterfaceId
OBJECT-TYPE
ID of the interface of neighbor.
1.3.6.1.4.1.2544.1.12.37.1.42.1.2Unsigned32read-onlycurrent
f3L3TrafficOspfV3NeighborPriority
OBJECT-TYPE
The priority of the neighbor.
1.3.6.1.4.1.2544.1.12.37.1.42.1.3Unsigned32read-onlycurrent
f3L3TrafficOspfV3NeighborDeadTime
OBJECT-TYPE
The Dead Time field indicates the amount of time remaining that the router waits to receive an OSPF hello packet from the neighbor before declaring the neighbor down.
1.3.6.1.4.1.2544.1.12.37.1.42.1.4Unsigned32read-onlycurrent
f3L3TrafficOspfV3NeighborLocalInterfaceName
OBJECT-TYPE
The name of local interface which discovers the neighbor.
1.3.6.1.4.1.2544.1.12.37.1.42.1.5DisplayStringread-onlycurrent
f3L3TrafficOspfV3NeighborState
OBJECT-TYPE
State of Link State Database synchronization with the neighbor.
1.3.6.1.4.1.2544.1.12.37.1.42.1.6OspfAdjacencyStateread-onlycurrent
f3L3TrafficOspfV3NeighborRole
OBJECT-TYPE
Role of the neighbor. DR, DR other and Backup are applicable.
1.3.6.1.4.1.2544.1.12.37.1.42.1.7TrafficOspfRoleread-onlycurrent
f3L3TrafficOspfV3NeighborIpAddress
OBJECT-TYPE
Link-local Address of interface of neighbor.
1.3.6.1.4.1.2544.1.12.37.1.42.1.8DisplayStringread-onlycurrent
f3L3TrafficOspfLinkLsDbTable
OBJECT-TYPE
OSPF Link State database. Must set f3VrfOspfRouterAction as optimizeOspfLinkLinkLsDbRetrieve(4) before get data from this table.
1.3.6.1.4.1.2544.1.12.37.1.43not-accessiblecurrent
f3L3TrafficOspfLinkLsDbEntry
OBJECT-TYPE
A conceptual row in the f3L3TrafficOspfLinkLsDbTable. Entries can be created/deleted in this table by management application action.
1.3.6.1.4.1.2544.1.12.37.1.43.1not-accessiblecurrent
f3L3TrafficOspfLinkLsDbType
OBJECT-TYPE
LSA Type.
1.3.6.1.4.1.2544.1.12.37.1.43.1.1OspfLsaTypenot-accessiblecurrent
f3L3TrafficOspfLinkLsDbId
OBJECT-TYPE
Link State ID.
1.3.6.1.4.1.2544.1.12.37.1.43.1.2IpAddressnot-accessiblecurrent
f3L3TrafficOspfLinkLsDbAdvRouterId
OBJECT-TYPE
Advertising Router ID.
1.3.6.1.4.1.2544.1.12.37.1.43.1.3IpAddressnot-accessiblecurrent
f3L3TrafficOspfLinkLsDbInterfaceId
OBJECT-TYPE
The interface id of the interface instance from which the LSA was received.
1.3.6.1.4.1.2544.1.12.37.1.43.1.4Unsigned32not-accessiblecurrent
f3L3TrafficOspfLinkLsDbInterface
OBJECT-TYPE
The local interface name from which the LSA was received.
1.3.6.1.4.1.2544.1.12.37.1.43.1.5DisplayStringnot-accessiblecurrent
f3L3TrafficOspfLinkLsDbAreaId
OBJECT-TYPE
Area ID.
1.3.6.1.4.1.2544.1.12.37.1.43.1.6IpAddressread-onlycurrent
f3L3TrafficOspfLinkLsDbChecksum
OBJECT-TYPE
The checksum associated with Link State Advertisement.
1.3.6.1.4.1.2544.1.12.37.1.43.1.7Unsigned32read-onlycurrent
f3L3TrafficOspfLinkLsDbSeqNum
OBJECT-TYPE
The Sequence Number associated with the last LSA.
1.3.6.1.4.1.2544.1.12.37.1.43.1.8Unsigned32read-onlycurrent
f3L3TrafficOspfLinkLsDbAge
OBJECT-TYPE
The age, in seconds, since this LSA was last received.
1.3.6.1.4.1.2544.1.12.37.1.43.1.9Unsigned32read-onlycurrent
f3L3TrafficOspfLinkLsDbRtrPriority
OBJECT-TYPE
Router priority for the interface.
1.3.6.1.4.1.2544.1.12.37.1.43.1.10Unsigned32read-onlycurrent
f3L3TrafficOspfLinkLsDbLinkLocalAddress
OBJECT-TYPE
The originating router's linklocal interface address for the link.
1.3.6.1.4.1.2544.1.12.37.1.43.1.11DisplayStringread-onlycurrent
f3L3TrafficOspfLinkLsDbPrefixList
OBJECT-TYPE
List of Prefixes associated with the link. In maximum, up to 16 prefixes are supported.
1.3.6.1.4.1.2544.1.12.37.1.43.1.12DisplayStringread-onlycurrent
f3L3TrafficIpv4StaticRouteTable
OBJECT-TYPE
A list of entries for the L3 Traffic Ipv4 Static route.
1.3.6.1.4.1.2544.1.12.37.1.44not-accessiblecurrent
f3L3TrafficIpv4StaticRouteEntry
OBJECT-TYPE
A conceptual row in the f3L3TrafficIpv4StaticRouteTable.
1.3.6.1.4.1.2544.1.12.37.1.44.1not-accessiblecurrent
f3L3TrafficIpv4StaticRouteDest
OBJECT-TYPE
It specifies the traffic Ipv4 Static route destination.
1.3.6.1.4.1.2544.1.12.37.1.44.1.1IpAddressnot-accessiblecurrent
f3L3TrafficIpv4StaticRouteMask
OBJECT-TYPE
It specifies the traffic Ipv4 Static route mask.
1.3.6.1.4.1.2544.1.12.37.1.44.1.2IpAddressnot-accessiblecurrent
f3L3TrafficIpv4StaticRouteNextHop
OBJECT-TYPE
It specifies the traffic Ipv4 Static route next hop.
1.3.6.1.4.1.2544.1.12.37.1.44.1.3DisplayStringnot-accessiblecurrent
f3L3TrafficIpv4StaticRouteInterface
OBJECT-TYPE
It specifies the traffic Ipv4 Static route interface.
1.3.6.1.4.1.2544.1.12.37.1.44.1.4DisplayStringnot-accessiblecurrent
f3L3TrafficIpv4StaticRouteMetric
OBJECT-TYPE
It specifies the traffic Ipv4 Static route metric.
1.3.6.1.4.1.2544.1.12.37.1.44.1.5Integer32read-writecurrent
f3L3TrafficIpv4StaticRouteSourceForwardingEnable
OBJECT-TYPE
It specifies the traffic Ipv4 static route source forwarding whether enabled.
1.3.6.1.4.1.2544.1.12.37.1.44.1.6TruthValueread-writecurrent
f3L3TrafficIpv4StaticRouteStorageType
OBJECT-TYPE
The type of storage configured for this entry.
1.3.6.1.4.1.2544.1.12.37.1.44.1.7StorageTyperead-createcurrent
f3L3TrafficIpv4StaticRouteRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3L3TrafficIpv4StaticRouteRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3L3TrafficIpv4StaticRouteRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3L3TrafficIpv4StaticRouteRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.37.1.44.1.8RowStatusread-createcurrent
f3L3TrafficIpv4AllRouteTable
OBJECT-TYPE
A list of entries for the L3 Traffic Ipv4 route. Must set f3VrfActionX as optimizeRouteRetrieve(3) before get data from this table.
1.3.6.1.4.1.2544.1.12.37.1.45not-accessiblecurrent
f3L3TrafficIpv4AllRouteEntry
OBJECT-TYPE
A conceptual row in the f3L3TrafficIpv4AllRouteTable.
1.3.6.1.4.1.2544.1.12.37.1.45.1not-accessiblecurrent
f3L3TrafficIpv4AllRouteDest
OBJECT-TYPE
It specifies the traffic Ipv4 route destination.
1.3.6.1.4.1.2544.1.12.37.1.45.1.1IpAddressnot-accessiblecurrent
f3L3TrafficIpv4AllRouteMask
OBJECT-TYPE
It specifies the traffic Ipv4 route mask.
1.3.6.1.4.1.2544.1.12.37.1.45.1.2IpAddressnot-accessiblecurrent
f3L3TrafficIpv4AllRouteNextHop
OBJECT-TYPE
It specifies the traffic Ipv4 route next hop.
1.3.6.1.4.1.2544.1.12.37.1.45.1.3DisplayStringnot-accessiblecurrent
f3L3TrafficIpv4AllRouteInterface
OBJECT-TYPE
It specifies the traffic Ipv4 route interface.
1.3.6.1.4.1.2544.1.12.37.1.45.1.4DisplayStringnot-accessiblecurrent
f3L3TrafficIpv4AllRouteOrigin
OBJECT-TYPE
The origin of IP Route.
1.3.6.1.4.1.2544.1.12.37.1.45.1.5TrafficIpRouteOriginTypenot-accessiblecurrent
f3L3TrafficIpv4AllRouteMetric
OBJECT-TYPE
It specifies the traffic Ipv4 route metric.
1.3.6.1.4.1.2544.1.12.37.1.45.1.6Integer32read-writecurrent
f3L3TrafficIpv4AllRouteSourceForwardingEnable
OBJECT-TYPE
It specifies the traffic Ipv4 route source forwarding whether enabled.
1.3.6.1.4.1.2544.1.12.37.1.45.1.7TruthValueread-writecurrent
f3L3TrafficIpv4AllRouteAdminDistance
OBJECT-TYPE
The Administrative Distance of IP Route.
1.3.6.1.4.1.2544.1.12.37.1.45.1.8Unsigned32read-onlycurrent
f3L3TrafficIpv4AllRouteStatus
OBJECT-TYPE
It specifies the traffic Ipv4 route status.
1.3.6.1.4.1.2544.1.12.37.1.45.1.9TrafficIpRouteStatusTyperead-onlycurrent
f3L3TrafficIpv4AllRouteStorageType
OBJECT-TYPE
The type of storage configured for this entry.
1.3.6.1.4.1.2544.1.12.37.1.45.1.10StorageTyperead-createcurrent
f3L3TrafficIpv4AllRouteRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3L3TrafficIpv4AllRouteRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3L3TrafficIpv4AllRouteRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3L3TrafficIpv4AllRouteRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.37.1.45.1.11RowStatusread-createcurrent
f3L3TrafficIpv6StaticRouteTable
OBJECT-TYPE
A list of entries for the L3 Traffic Ipv6 static route.
1.3.6.1.4.1.2544.1.12.37.1.46not-accessiblecurrent
f3L3TrafficIpv6StaticRouteEntry
OBJECT-TYPE
A conceptual row in the f3L3TrafficIpv6StaticRouteTable.
1.3.6.1.4.1.2544.1.12.37.1.46.1not-accessiblecurrent
f3L3TrafficIpv6StaticRouteDest
OBJECT-TYPE
The destination IP address of this route. This object may not take a Multicast (Class D) address value. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical-AND of x with the value of the corresponding instance of the static-route-mask attribute is not equal to x.
1.3.6.1.4.1.2544.1.12.37.1.46.1.1Ipv6Addressnot-accessiblecurrent
f3L3TrafficIpv6StaticRoutePrefixLength
OBJECT-TYPE
Indicate the mask to be logically ANDed with the destination address before being compared to the value in the cmStaticRouteDest field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the static route mask by reference to the IP Address Class. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical AND of x with the value of the corresponding instance of the static-route-dest attribute is not equal to static route destination.
1.3.6.1.4.1.2544.1.12.37.1.46.1.2Integer32not-accessiblecurrent
f3L3TrafficIpv6StaticRouteNextHop
OBJECT-TYPE
The address of the next router en route.
1.3.6.1.4.1.2544.1.12.37.1.46.1.3DisplayStringnot-accessiblecurrent
f3L3TrafficIpv6StaticRouteInterface
OBJECT-TYPE
Name of the IP interface for the interface static route.
1.3.6.1.4.1.2544.1.12.37.1.46.1.4DisplayString (SIZE(0..15))not-accessiblecurrent
f3L3TrafficIpv6StaticRouteMetric
OBJECT-TYPE
The primary routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's cmStaticRouteProto value. If this metric is not used, its value should be set to 1.
1.3.6.1.4.1.2544.1.12.37.1.46.1.5Integer32read-writecurrent
f3L3TrafficIpv6StaticRouteStorageType
OBJECT-TYPE
The storage type for this conceptual row.
1.3.6.1.4.1.2544.1.12.37.1.46.1.6StorageTyperead-createcurrent
f3L3TrafficIpv6StaticRouteRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3L3TrafficIpv6StaticRouteRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3L3TrafficIpv6StaticRouteRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3L3TrafficIpv6StaticRouteRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.37.1.46.1.7RowStatusread-createcurrent
f3L3TrafficIpv6AllRouteTable
OBJECT-TYPE
A list of entries for the L3 Traffic Ipv6 route. Must set f3VrfActionX as optimizeIpv6RouteRetrieve(7) before get data from this table.
1.3.6.1.4.1.2544.1.12.37.1.47not-accessiblecurrent
f3L3TrafficIpv6AllRouteEntry
OBJECT-TYPE
A conceptual row in the f3L3TrafficIpv6AllRouteTable.
1.3.6.1.4.1.2544.1.12.37.1.47.1not-accessiblecurrent
f3L3TrafficIpv6AllRouteDest
OBJECT-TYPE
The destination IP address of this route. This object may not take a Multicast (Class D) address value. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical-AND of x with the value of the corresponding instance of the static-route-mask attribute is not equal to x.
1.3.6.1.4.1.2544.1.12.37.1.47.1.1Ipv6Addressnot-accessiblecurrent
f3L3TrafficIpv6AllRoutePrefixLength
OBJECT-TYPE
Indicate the mask to be logically ANDed with the destination address before being compared to the value in the cmStaticRouteDest field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the static route mask by reference to the IP Address Class. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical AND of x with the value of the corresponding instance of the static-route-dest attribute is not equal to static route destination.
1.3.6.1.4.1.2544.1.12.37.1.47.1.2Integer32not-accessiblecurrent
f3L3TrafficIpv6AllRouteNextHop
OBJECT-TYPE
The address of the next router en route.
1.3.6.1.4.1.2544.1.12.37.1.47.1.3DisplayStringnot-accessiblecurrent
f3L3TrafficIpv6AllRouteInterface
OBJECT-TYPE
Name of the IP interface for the interface static route.
1.3.6.1.4.1.2544.1.12.37.1.47.1.4DisplayString (SIZE(0..15))not-accessiblecurrent
f3L3TrafficIpv6AllRouteOrigin
OBJECT-TYPE
The origin of IP Route.
1.3.6.1.4.1.2544.1.12.37.1.47.1.5TrafficIpRouteOriginTypenot-accessiblecurrent
f3L3TrafficIpv6AllRouteMetric
OBJECT-TYPE
The primary routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's cmStaticRouteProto value. If this metric is not used, its value should be set to 1.
1.3.6.1.4.1.2544.1.12.37.1.47.1.6Integer32read-writecurrent
f3L3TrafficIpv6AllRouteAdminDistance
OBJECT-TYPE
The Administrative Distance of IP Route.
1.3.6.1.4.1.2544.1.12.37.1.47.1.7Unsigned32read-onlycurrent
f3L3TrafficIpv6AllRouteStatus
OBJECT-TYPE
It specifies the traffic Ipv6 route status.
1.3.6.1.4.1.2544.1.12.37.1.47.1.8TrafficIpRouteStatusread-onlycurrent
f3L3TrafficIpv6AllRouteStorageType
OBJECT-TYPE
The storage type for this conceptual row.
1.3.6.1.4.1.2544.1.12.37.1.47.1.9StorageTyperead-createcurrent
f3L3TrafficIpv6AllRouteRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3L3TrafficIpv6AllRouteRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3L3TrafficIpv6AllRouteRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3L3TrafficIpv6AllRouteRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.37.1.47.1.10RowStatusread-createcurrent
f3IpPrefixListTable
OBJECT-TYPE
IP Prefix List table.
1.3.6.1.4.1.2544.1.12.37.1.48not-accessiblecurrent
f3IpPrefixListEntry
OBJECT-TYPE
A conceptual row in the f3IpPrefixListTable. Entries can be created/deleted in this table by management application action.
1.3.6.1.4.1.2544.1.12.37.1.48.1not-accessiblecurrent
f3IpPrefixListIndex
OBJECT-TYPE
An integer index value used to uniquely identify this IP Prefix List within a VRF.
1.3.6.1.4.1.2544.1.12.37.1.48.1.1Integer32not-accessiblecurrent
f3IpPrefixListName
OBJECT-TYPE
The name of IP Prefix List.
1.3.6.1.4.1.2544.1.12.37.1.48.1.2DisplayStringread-createcurrent
f3IpPrefixListDefaultDisposition
OBJECT-TYPE
This indicates the default disposition for the prefix that does not match any prefix in the prefix list..
1.3.6.1.4.1.2544.1.12.37.1.48.1.3IpPrefixDispositionTyperead-writecurrent
f3IpPrefixListStorageType
OBJECT-TYPE
The storage type for this conceptual row.
1.3.6.1.4.1.2544.1.12.37.1.48.1.4StorageTyperead-createcurrent
f3IpPrefixListRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3IpPrefixListRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3IpPrefixListRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3IpPrefixListRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.37.1.48.1.5RowStatusread-createcurrent
f3IpPrefixTable
OBJECT-TYPE
IP Prefix table.
1.3.6.1.4.1.2544.1.12.37.1.49not-accessiblecurrent
f3IpPrefixEntry
OBJECT-TYPE
A conceptual row in the f3IpPrefixTable. Entries can be created/deleted in this table by management application action.
1.3.6.1.4.1.2544.1.12.37.1.49.1not-accessiblecurrent
f3IpPrefixIndex
OBJECT-TYPE
An integer index value used to uniquely identify this IP Prefix entry within a IP Prefix List.
1.3.6.1.4.1.2544.1.12.37.1.49.1.1Integer32not-accessiblecurrent
f3IpPrefix
OBJECT-TYPE
The IP Prefix. The length is up to 64 characters.
1.3.6.1.4.1.2544.1.12.37.1.49.1.2DisplayStringread-createcurrent
f3IpPrefixPriority
OBJECT-TYPE
This dictates the order in which this entry is applied relative to the IP Prefix List. These values need not be sequential and can have gaps. The priority of the IP Prefix Entry within a list shall be unique. Higher the value lower the priority.
1.3.6.1.4.1.2544.1.12.37.1.49.1.3Unsigned32read-writecurrent
f3IpPrefixDisposition
OBJECT-TYPE
This indicates whether to permit or deny the prefix.
1.3.6.1.4.1.2544.1.12.37.1.49.1.4IpPrefixDispositionTyperead-writecurrent
f3IpPrefixLessOrEqualPrefixLen
OBJECT-TYPE
This allows specifying a prefix length which allows filtering networks with more specific prefixes within this Prefix attribute. For example, if this value is 16 and the Prefix attribute is <10.0.0.0/8>, then all the networks in 10.0.0.0/8 that have prefix that is 16 or less will be filtered. A specific value of Prefix 0.0.0.0/0 with a value of 32 for this attribute implies all the networks and it could be used for the rule with highest priority value (lowest priority) that permits all networks that have not been filtered by higher priority entries.
1.3.6.1.4.1.2544.1.12.37.1.49.1.5Integer32read-writecurrent
f3IpPrefixGreaterOrEqualPrefixLen
OBJECT-TYPE
This allows specifying a prefix length which allows filtering all networks in the specified Prefix that are at least the length specified for this attribute. This attribute value shall be greater than the Prefix Length of the Prefix attribute. For example, if this value is 16 and the Prefix attribute is <10.0.0.0/8>, then all the networks in 10.0.0.0/8 with a prefix greater than or equal to 16 are filtered.
1.3.6.1.4.1.2544.1.12.37.1.49.1.6Integer32read-writecurrent
f3IpPrefixStorageType
OBJECT-TYPE
The storage type for this conceptual row.
1.3.6.1.4.1.2544.1.12.37.1.49.1.7StorageTyperead-createcurrent
f3IpPrefixRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3IpPrefixRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3IpPrefixRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3IpPrefixRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.37.1.49.1.8RowStatusread-createcurrent
f3L3TrafficIPInterfaceRAPrefixTable
OBJECT-TYPE
Traffic IP interface RAP prefix table.
1.3.6.1.4.1.2544.1.12.37.1.50not-accessiblecurrent
f3L3TrafficIPInterfaceRAPrefixEntry
OBJECT-TYPE
A conceptual row in f3L3TrafficIPInterfaceRAPrefixTable.
1.3.6.1.4.1.2544.1.12.37.1.50.1not-accessiblecurrent
f3L3TrafficIPInterfaceRAPrefixIndex
OBJECT-TYPE
The unique integer index value corresponding to a traffic IP interface RA prefix.
1.3.6.1.4.1.2544.1.12.37.1.50.1.1Integer32not-accessiblecurrent
f3L3TrafficIPInterfaceRAPrefixAdvertiseEnabled
OBJECT-TYPE
This attribute is to enable to Advertise prefix to link in router mode.
1.3.6.1.4.1.2544.1.12.37.1.50.1.2TruthValueread-writecurrent
f3L3TrafficIPInterfaceRAPrefix
OBJECT-TYPE
This is the IPv6 Prefix to be dispatched to the link in Router mode.
1.3.6.1.4.1.2544.1.12.37.1.50.1.3Ipv6Addressread-writecurrent
f3L3TrafficIPInterfaceRAPrefixLength
OBJECT-TYPE
Prefix length.
1.3.6.1.4.1.2544.1.12.37.1.50.1.4Integer32read-writecurrent
f3L3TrafficIPInterfaceRAPrefixValidLifeTime
OBJECT-TYPE
This attribute is used to specify fixed Valid lifetime of distributed prefix in seconds All ones may be set for unlimited lifetime.
1.3.6.1.4.1.2544.1.12.37.1.50.1.5Unsigned32read-writecurrent
f3L3TrafficIPInterfaceRAPrefixPreferredLifeTime
OBJECT-TYPE
This attribute is used to specify fixed time interval for unrestricted use of prefix. When this time has been expired the address is considered as deprecated as specified in RFC4862 Preferred lifetime shall not be greater than the Valid Lifetime. All ones may be set for unlimited lifetime.
1.3.6.1.4.1.2544.1.12.37.1.50.1.6Unsigned32read-writecurrent
f3L3TrafficIPInterfaceRAPrefixStorageType
OBJECT-TYPE
The storage type for this conceptual row.
1.3.6.1.4.1.2544.1.12.37.1.50.1.7StorageTyperead-createcurrent
f3L3TrafficIPInterfaceRAPrefixRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3L3TrafficIPInterfaceRAPrefixRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3L3TrafficIPInterfaceRAPrefixRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3L3TrafficIPInterfaceRAPrefixRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.37.1.50.1.8RowStatusread-createcurrent
f3L3TrafficIPInterfaceNdpTable
OBJECT-TYPE
Traffic IPv6 NDP table. Must set f3L3TrafficIPIfActionX as optimizeNdpRetrieve(2) before get data from this table.
1.3.6.1.4.1.2544.1.12.37.1.51not-accessiblecurrent
f3L3TrafficIPInterfaceNdpEntry
OBJECT-TYPE
A conceptual row in f3L3TrafficIPInterfaceNdpTable.
1.3.6.1.4.1.2544.1.12.37.1.51.1not-accessiblecurrent
f3L3TrafficIPInterfaceNdpIPv6Addr
OBJECT-TYPE
This is the IP address of the NDP Entry.
1.3.6.1.4.1.2544.1.12.37.1.51.1.1Ipv6Addressnot-accessiblecurrent
f3L3TrafficIPInterfaceNdpInterface
OBJECT-TYPE
This is the IP interface for the NDP Entry.
1.3.6.1.4.1.2544.1.12.37.1.51.1.2DisplayString (SIZE(0..15))read-createcurrent
f3L3TrafficIPInterfaceNdpMacAddress
OBJECT-TYPE
This is the MAC address of the NDP Entry.
1.3.6.1.4.1.2544.1.12.37.1.51.1.3MacAddressread-createcurrent
f3L3TrafficIPInterfaceNdpType
OBJECT-TYPE
The type of NDP Entry. Note that static entries can be created.
1.3.6.1.4.1.2544.1.12.37.1.51.1.4IpEntryTyperead-createcurrent
f3L3TrafficIPInterfaceNdpReachabilityState
OBJECT-TYPE
This is the reachability state of the NDP Entry.
1.3.6.1.4.1.2544.1.12.37.1.51.1.5NdpNeighborReachabilityStateread-onlycurrent
f3L3TrafficIPInterfaceNdpAge
OBJECT-TYPE
Indicates entry age in seconds.
1.3.6.1.4.1.2544.1.12.37.1.51.1.6Integer32read-onlycurrent
f3L3TrafficIPInterfaceNdpStorageType
OBJECT-TYPE
The storage type for this conceptual row.
1.3.6.1.4.1.2544.1.12.37.1.51.1.7StorageTyperead-createcurrent
f3L3TrafficIPInterfaceNdpRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3L3TrafficIPInterfaceNdpRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3L3TrafficIPInterfaceNdpRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3L3TrafficIPInterfaceNdpRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.37.1.51.1.8RowStatusread-createcurrent
f3L3TrafficIPInterfaceIPv6AddressTable
OBJECT-TYPE
Traffic interface IPv6 address table. Must set f3L3TrafficIPIfActionX as optimizeIPv6AddressEntryRetrieve(3) before get data from this table.
1.3.6.1.4.1.2544.1.12.37.1.52not-accessiblecurrent
f3L3TrafficIPInterfaceIPv6AddressEntry
OBJECT-TYPE
A conceptual row in the f3L3TrafficIPInterfaceIPv6AddressTable.
1.3.6.1.4.1.2544.1.12.37.1.52.1not-accessiblecurrent
f3L3TrafficIPInterfaceIPv6AddressIndex
OBJECT-TYPE
The unique integer index value corresponding to a traffic IP interface IPv6 unicast address.
1.3.6.1.4.1.2544.1.12.37.1.52.1.1Integer32not-accessiblecurrent
f3L3TrafficIPInterfaceIPv6AddressAssignMode
OBJECT-TYPE
The assignment mode of IPv6 Unicast Address.
1.3.6.1.4.1.2544.1.12.37.1.52.1.2Ipv6AddressAssignModeread-writecurrent
f3L3TrafficIPInterfaceIPv6AddressUnicastAddr
OBJECT-TYPE
This is IPv6 Unicast Address.
1.3.6.1.4.1.2544.1.12.37.1.52.1.3Ipv6Addressread-writecurrent
f3L3TrafficIPInterfaceIPv6AddressUnicastAddrPrefixLength
OBJECT-TYPE
This is prefix length of the unicast address.
1.3.6.1.4.1.2544.1.12.37.1.52.1.4Integer32read-writecurrent
f3L3TrafficIPInterfaceIPv6AddressUnicastAddrAutoGenPrefix
OBJECT-TYPE
This is prefix of the unicast address in automatic address assignment mode.
1.3.6.1.4.1.2544.1.12.37.1.52.1.5DisplayStringread-writecurrent
f3L3TrafficIPInterfaceIPv6AddressStorageType
OBJECT-TYPE
The storage type for this conceptual row.
1.3.6.1.4.1.2544.1.12.37.1.52.1.6StorageTyperead-createcurrent
f3L3TrafficIPInterfaceIPv6AddressRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3L3TrafficIPInterfaceIPv6AddressRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3L3TrafficIPInterfaceIPv6AddressRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3L3TrafficIPInterfaceIPv6AddressRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.37.1.52.1.7RowStatusread-createcurrent
f3L3Performance
OBJECT-IDENTITY
1.3.6.1.4.1.2544.1.12.37.2
f3L3FlowPointStatsTable
OBJECT-TYPE
A collection of L3 Flow Point related statistics. These reflect the current data.
1.3.6.1.4.1.2544.1.12.37.2.1not-accessiblecurrent
f3L3FlowPointStatsEntry
OBJECT-TYPE
A conceptual row in the f3L3FlowPointStatsTable. Entries exist in this table for each L3 flow point.
1.3.6.1.4.1.2544.1.12.37.2.1.1not-accessiblecurrent
f3L3FlowPointStatsIndex
OBJECT-TYPE
An arbitrary integer index value used to uniquely identify this L3 flow point statistics entry. 1 - 15min 2 - 1day 3 - rollover 4 - 5min
1.3.6.1.4.1.2544.1.12.37.2.1.1.1Integer32 (1..4)read-onlycurrent
f3L3FlowPointStatsIntervalType
OBJECT-TYPE
Interval over which Performance Monitoring data is collected.
1.3.6.1.4.1.2544.1.12.37.2.1.1.2CmPmIntervalTyperead-onlycurrent
f3L3FlowPointStatsValid
OBJECT-TYPE
Indicates the validity of the bin.
1.3.6.1.4.1.2544.1.12.37.2.1.1.3TruthValueread-onlycurrent
f3L3FlowPointStatsAction
OBJECT-TYPE
Allows the Manager to clear the bin.
1.3.6.1.4.1.2544.1.12.37.2.1.1.4CmPmBinActionread-writecurrent
f3L3FlowPointStatsFMG
OBJECT-TYPE
The number of Frames Marked Green.
1.3.6.1.4.1.2544.1.12.37.2.1.1.5PerfCounter64read-onlycurrent
f3L3FlowPointStatsFMY
OBJECT-TYPE
The number of Frames Marked Yellow.
1.3.6.1.4.1.2544.1.12.37.2.1.1.6PerfCounter64read-onlycurrent
f3L3FlowPointStatsFMRD
OBJECT-TYPE
The number of Frames Marked Red and Discarded.
1.3.6.1.4.1.2544.1.12.37.2.1.1.7PerfCounter64read-onlycurrent
f3L3FlowPointStatsFTD
OBJECT-TYPE
The number of Frames Tail Dropped.
1.3.6.1.4.1.2544.1.12.37.2.1.1.8PerfCounter64read-onlycurrent
f3L3FlowPointStatsFragmentedDropAcl
OBJECT-TYPE
The number of dropped fragmented packets.
1.3.6.1.4.1.2544.1.12.37.2.1.1.9PerfCounter64read-onlycurrent
f3L3FlowPointStatsAclRuleDrop
OBJECT-TYPE
The number of dropped packets due to ACL rule.
1.3.6.1.4.1.2544.1.12.37.2.1.1.10PerfCounter64read-onlycurrent
f3L3FlowPointStatsTtlEqual1Drop
OBJECT-TYPE
the number of dropped packets due to ttl's value is 1.
1.3.6.1.4.1.2544.1.12.37.2.1.1.11PerfCounter64read-onlycurrent
f3L3FlowPointStatsFrameTx
OBJECT-TYPE
The number of total transmitted frames.
1.3.6.1.4.1.2544.1.12.37.2.1.1.12PerfCounter64read-onlycurrent
f3L3FlowPointStatsFrameRx
OBJECT-TYPE
The number of total received frames.
1.3.6.1.4.1.2544.1.12.37.2.1.1.13PerfCounter64read-onlycurrent
f3L3FlowPointStatsNoRouteDrop
OBJECT-TYPE
The number of frames drop due to no route.
1.3.6.1.4.1.2544.1.12.37.2.1.1.14PerfCounter64read-onlycurrent
f3L3FlowPointStatsHopLimitDrop
OBJECT-TYPE
The number of frames drop due to hop limit.
1.3.6.1.4.1.2544.1.12.37.2.1.1.15PerfCounter64read-onlycurrent
f3L3FlowPointHistoryTable
OBJECT-TYPE
A collection of L3 Flow Point related statistics. These reflect the current data.
1.3.6.1.4.1.2544.1.12.37.2.2not-accessiblecurrent
f3L3FlowPointHistoryEntry
OBJECT-TYPE
A conceptual row in the f3L3FlowPointHistoryTable. Entries exist in this table for each L3 flow point.
1.3.6.1.4.1.2544.1.12.37.2.2.1not-accessiblecurrent
f3L3FlowPointHistoryIndex
OBJECT-TYPE
An arbitrary integer index value used to uniquely identify this L3 flow point statistics entry. 1 - 15min 2 - 1day 3 - rollover 4 - 5min
1.3.6.1.4.1.2544.1.12.37.2.2.1.1Integer32 (1..65535)read-onlycurrent
f3L3FlowPointHistoryTime
OBJECT-TYPE
Indicates the time of history bin creation.
1.3.6.1.4.1.2544.1.12.37.2.2.1.2DateAndTimeread-onlycurrent
f3L3FlowPointHistoryValid
OBJECT-TYPE
Indicates the validity of the bin.
1.3.6.1.4.1.2544.1.12.37.2.2.1.3TruthValueread-onlycurrent
f3L3FlowPointHistoryAction
OBJECT-TYPE
Allows the Manager to clear the bin.
1.3.6.1.4.1.2544.1.12.37.2.2.1.4CmPmBinActionread-writecurrent
f3L3FlowPointHistoryFMG
OBJECT-TYPE
The number of Frames Marked Green.
1.3.6.1.4.1.2544.1.12.37.2.2.1.5PerfCounter64read-onlycurrent
f3L3FlowPointHistoryFMY
OBJECT-TYPE
The number of Frames Marked Yellow.
1.3.6.1.4.1.2544.1.12.37.2.2.1.6PerfCounter64read-onlycurrent
f3L3FlowPointHistoryFMRD
OBJECT-TYPE
The number of Frames Marked Red and Discarded.
1.3.6.1.4.1.2544.1.12.37.2.2.1.7PerfCounter64read-onlycurrent
f3L3FlowPointHistoryFTD
OBJECT-TYPE
The number of Frames Tail Dropped.
1.3.6.1.4.1.2544.1.12.37.2.2.1.8PerfCounter64read-onlycurrent
f3L3FlowPointHistoryFragmentedDropAcl
OBJECT-TYPE
The number of dropped fragmented packets.
1.3.6.1.4.1.2544.1.12.37.2.2.1.9PerfCounter64read-onlycurrent
f3L3FlowPointHistoryAclRuleDrop
OBJECT-TYPE
The number of dropped packets due to ACL rule.
1.3.6.1.4.1.2544.1.12.37.2.2.1.10PerfCounter64read-onlycurrent
f3L3FlowPointHistoryTtlEqual1Drop
OBJECT-TYPE
the number of dropped packets due to ttl's value is 1.
1.3.6.1.4.1.2544.1.12.37.2.2.1.11PerfCounter64read-onlycurrent
f3L3FlowPointHistoryFrameTx
OBJECT-TYPE
The number of total transmitted frames.
1.3.6.1.4.1.2544.1.12.37.2.2.1.12PerfCounter64read-onlycurrent
f3L3FlowPointHistoryFrameRx
OBJECT-TYPE
the number of total recieved frames.
1.3.6.1.4.1.2544.1.12.37.2.2.1.13PerfCounter64read-onlycurrent
f3L3FlowPointHistoryNoRouteDrop
OBJECT-TYPE
the number of frames dropped due to no route.
1.3.6.1.4.1.2544.1.12.37.2.2.1.14PerfCounter64read-onlycurrent
f3L3FlowPointHistoryHopLimitDrop
OBJECT-TYPE
the number of frames dropped due to hop limit.
1.3.6.1.4.1.2544.1.12.37.2.2.1.15PerfCounter64read-onlycurrent
f3L3FlowPointThresholdTable
OBJECT-TYPE
A table of entries that allow manageability of L3 Flow Point Thresholds.
1.3.6.1.4.1.2544.1.12.37.2.3not-accessiblecurrent
f3L3FlowPointThresholdEntry
OBJECT-TYPE
A conceptual row in the f3L3FlowPointThresholdTable.
1.3.6.1.4.1.2544.1.12.37.2.3.1not-accessiblecurrent
f3L3FlowPointThresholdIndex
OBJECT-TYPE
An index that uniquely identifies an entry in the f3L3FlowPointThresholdTable.
1.3.6.1.4.1.2544.1.12.37.2.3.1.1Integer32 (1..65535)read-onlycurrent
f3L3FlowPointThresholdInterval
OBJECT-TYPE
The interval over which monitored value is sampled and compared with the specified threshold.
1.3.6.1.4.1.2544.1.12.37.2.3.1.2CmPmIntervalTyperead-onlycurrent
f3L3FlowPointThresholdVariable
OBJECT-TYPE
The object identifier of the particular variable to be sampled.
1.3.6.1.4.1.2544.1.12.37.2.3.1.3VariablePointerread-onlycurrent
f3L3FlowPointThresholdValueLo
OBJECT-TYPE
Lower 32 bits of the threshold value.
1.3.6.1.4.1.2544.1.12.37.2.3.1.4Unsigned32read-writecurrent
f3L3FlowPointThresholdValueHi
OBJECT-TYPE
Higher 32 bits of the threshold value.
1.3.6.1.4.1.2544.1.12.37.2.3.1.5Unsigned32read-writecurrent
f3L3FlowPointThresholdMonValue
OBJECT-TYPE
Monitored value corresponding to f3L3FlowPointThresholdVariable.
1.3.6.1.4.1.2544.1.12.37.2.3.1.6Counter64read-onlycurrent
f3L3TrafficIpInterfaceStatsTable
OBJECT-TYPE
A collection of L3 traffic ip interface related statistics. These reflect the current data.
1.3.6.1.4.1.2544.1.12.37.2.4not-accessiblecurrent
f3L3TrafficIpInterfaceStatsEntry
OBJECT-TYPE
A conceptual row in the f3L3TrafficIpInterfaceStatsTable. Entries exist in this table for each L3 traffic ip interface.
1.3.6.1.4.1.2544.1.12.37.2.4.1not-accessiblecurrent
f3L3TrafficIpInterfaceStatsIndex
OBJECT-TYPE
An arbitrary integer index value used to uniquely identify this L3 flow point statistics entry. 1 - 15min 2 - 1day 3 - rollover 4 - 5min
1.3.6.1.4.1.2544.1.12.37.2.4.1.1Integer32 (1..4)read-onlycurrent
f3L3TrafficIpInterfaceStatsIntervalType
OBJECT-TYPE
Interval over which Performance Monitoring data is collected.
1.3.6.1.4.1.2544.1.12.37.2.4.1.2CmPmIntervalTyperead-onlycurrent
f3L3TrafficIpInterfaceStatsValid
OBJECT-TYPE
Indicates the validity of the bin.
1.3.6.1.4.1.2544.1.12.37.2.4.1.3TruthValueread-onlycurrent
f3L3TrafficIpInterfaceStatsAction
OBJECT-TYPE
Allows the Manager to clear the bin.
1.3.6.1.4.1.2544.1.12.37.2.4.1.4CmPmBinActionread-writecurrent
f3L3TrafficIpInterfaceStatsDhcpTx
OBJECT-TYPE
The number of packets DHCP Transmit.
1.3.6.1.4.1.2544.1.12.37.2.4.1.5PerfCounter64read-onlycurrent
f3L3TrafficIpInterfaceStatsDhcpRx
OBJECT-TYPE
The number of packets DHCP Recieved.
1.3.6.1.4.1.2544.1.12.37.2.4.1.6PerfCounter64read-onlycurrent
f3L3TrafficIpInterfaceStatsIcmpTx
OBJECT-TYPE
The number of packets Icmp protocol transmit.
1.3.6.1.4.1.2544.1.12.37.2.4.1.7PerfCounter64read-onlycurrent
f3L3TrafficIpInterfaceStatsIcmpRx
OBJECT-TYPE
The number of packets Icmp protocol recieved.
1.3.6.1.4.1.2544.1.12.37.2.4.1.8PerfCounter64read-onlycurrent
f3L3TrafficIpInterfaceStatsArpReqTx
OBJECT-TYPE
The number of transmit packets due to ARP request.
1.3.6.1.4.1.2544.1.12.37.2.4.1.9PerfCounter64read-onlycurrent
f3L3TrafficIpInterfaceStatsArpReqRx
OBJECT-TYPE
The number of recieved packets due to ARP request.
1.3.6.1.4.1.2544.1.12.37.2.4.1.10PerfCounter64read-onlycurrent
f3L3TrafficIpInterfaceStatsArpReplyTx
OBJECT-TYPE
The number of transmit packets due to ARP reply.
1.3.6.1.4.1.2544.1.12.37.2.4.1.11PerfCounter64read-onlycurrent
f3L3TrafficIpInterfaceStatsArpReplyRx
OBJECT-TYPE
The number of recieved packets due to ARP reply.
1.3.6.1.4.1.2544.1.12.37.2.4.1.12PerfCounter64read-onlycurrent
f3L3TrafficIpInterfaceStatsDhcpV6Tx
OBJECT-TYPE
The number of packets DHCPv6 Transmit.
1.3.6.1.4.1.2544.1.12.37.2.4.1.13PerfCounter64read-onlycurrent
f3L3TrafficIpInterfaceStatsDhcpV6Rx
OBJECT-TYPE
The number of packets DHCPv6 Recieved.
1.3.6.1.4.1.2544.1.12.37.2.4.1.14PerfCounter64read-onlycurrent
f3L3TrafficIpInterfaceStatsIcmpV6WONdpTx
OBJECT-TYPE
The number of packets Icmpv6 protocol transmit.
1.3.6.1.4.1.2544.1.12.37.2.4.1.15PerfCounter64read-onlycurrent
f3L3TrafficIpInterfaceStatsIcmpV6WONdpRx
OBJECT-TYPE
The number of packets Icmpv6 protocol recieved.
1.3.6.1.4.1.2544.1.12.37.2.4.1.16PerfCounter64read-onlycurrent
f3L3TrafficIpInterfaceStatsNdpNSTx
OBJECT-TYPE
The number of transmit NS message.
1.3.6.1.4.1.2544.1.12.37.2.4.1.17PerfCounter64read-onlycurrent
f3L3TrafficIpInterfaceStatsNdpNSRx
OBJECT-TYPE
The number of recieved NS message.
1.3.6.1.4.1.2544.1.12.37.2.4.1.18PerfCounter64read-onlycurrent
f3L3TrafficIpInterfaceStatsNdpNATx
OBJECT-TYPE
The number of transmit NA message.
1.3.6.1.4.1.2544.1.12.37.2.4.1.19PerfCounter64read-onlycurrent
f3L3TrafficIpInterfaceStatsNdpNARx
OBJECT-TYPE
The number of recieved NA message.
1.3.6.1.4.1.2544.1.12.37.2.4.1.20PerfCounter64read-onlycurrent
f3L3TrafficIpInterfaceStatsNdpRATx
OBJECT-TYPE
The number of transmit RA message.
1.3.6.1.4.1.2544.1.12.37.2.4.1.21PerfCounter64read-onlycurrent
f3L3TrafficIpInterfaceStatsNdpRARx
OBJECT-TYPE
The number of recieved RA message.
1.3.6.1.4.1.2544.1.12.37.2.4.1.22PerfCounter64read-onlycurrent
f3L3TrafficIpInterfaceStatsNdpRSTx
OBJECT-TYPE
The number of transmit RS message.
1.3.6.1.4.1.2544.1.12.37.2.4.1.23PerfCounter64read-onlycurrent
f3L3TrafficIpInterfaceStatsNdpRSRx
OBJECT-TYPE
The number of recieved RS message.
1.3.6.1.4.1.2544.1.12.37.2.4.1.24PerfCounter64read-onlycurrent
f3L3TrafficIpInterfaceHistoryTable
OBJECT-TYPE
A collection of L3 traffic ip interface related history statistics. These reflect the history data.
1.3.6.1.4.1.2544.1.12.37.2.5not-accessiblecurrent
f3L3TrafficIpInterfaceHistoryEntry
OBJECT-TYPE
A conceptual row in the f3L3TrafficIpInterfaceHistoryTable. Entries exist in this table for each L3 traffic ip interface.
1.3.6.1.4.1.2544.1.12.37.2.5.1not-accessiblecurrent
f3L3TrafficIpInterfaceHistoryIndex
OBJECT-TYPE
An arbitrary integer index value used to uniquely identify the history bin
1.3.6.1.4.1.2544.1.12.37.2.5.1.1Integer32 (1..65535)read-onlycurrent
f3L3TrafficIpInterfaceHistoryTime
OBJECT-TYPE
Indicates the time of history bin creation.
1.3.6.1.4.1.2544.1.12.37.2.5.1.2DateAndTimeread-onlycurrent
f3L3TrafficIpInterfaceHistoryValid
OBJECT-TYPE
Indicates the validity of the bin.
1.3.6.1.4.1.2544.1.12.37.2.5.1.3TruthValueread-onlycurrent
f3L3TrafficIpInterfaceHistoryAction
OBJECT-TYPE
Allows the Manager to clear the bin.
1.3.6.1.4.1.2544.1.12.37.2.5.1.4CmPmBinActionread-writecurrent
f3L3TrafficIpInterfaceHistoryDhcpTx
OBJECT-TYPE
The number of packets DHCP Transmit.
1.3.6.1.4.1.2544.1.12.37.2.5.1.5PerfCounter64read-onlycurrent
f3L3TrafficIpInterfaceHistoryDhcpRx
OBJECT-TYPE
The number of packets DHCP Recieved.
1.3.6.1.4.1.2544.1.12.37.2.5.1.6PerfCounter64read-onlycurrent
f3L3TrafficIpInterfaceHistoryIcmpTx
OBJECT-TYPE
The number of packets Icmp protocol transmit.
1.3.6.1.4.1.2544.1.12.37.2.5.1.7PerfCounter64read-onlycurrent
f3L3TrafficIpInterfaceHistoryIcmpRx
OBJECT-TYPE
The number of packets Icmp protocol recieved.
1.3.6.1.4.1.2544.1.12.37.2.5.1.8PerfCounter64read-onlycurrent
f3L3TrafficIpInterfaceHistoryArpReqTx
OBJECT-TYPE
The number of transmit packets due to ARP request.
1.3.6.1.4.1.2544.1.12.37.2.5.1.9PerfCounter64read-onlycurrent
f3L3TrafficIpInterfaceHistoryArpReqRx
OBJECT-TYPE
the number of recieved packets due to ARP request.
1.3.6.1.4.1.2544.1.12.37.2.5.1.10PerfCounter64read-onlycurrent
f3L3TrafficIpInterfaceHistoryArpReplyTx
OBJECT-TYPE
The number of transmit packets due to ARP reply.
1.3.6.1.4.1.2544.1.12.37.2.5.1.11PerfCounter64read-onlycurrent
f3L3TrafficIpInterfaceHistoryArpReplyRx
OBJECT-TYPE
the number of recieved packets due to ARP reply.
1.3.6.1.4.1.2544.1.12.37.2.5.1.12PerfCounter64read-onlycurrent
f3L3TrafficIpInterfaceHistoryDhcpV6Tx
OBJECT-TYPE
The number of packets DHCPv6 Transmit.
1.3.6.1.4.1.2544.1.12.37.2.5.1.13PerfCounter64read-onlycurrent
f3L3TrafficIpInterfaceHistoryDhcpV6Rx
OBJECT-TYPE
The number of packets DHCPv6 Recieved.
1.3.6.1.4.1.2544.1.12.37.2.5.1.14PerfCounter64read-onlycurrent
f3L3TrafficIpInterfaceHistoryIcmpV6WONdpTx
OBJECT-TYPE
The number of packets Icmpv6 protocol transmit.
1.3.6.1.4.1.2544.1.12.37.2.5.1.15PerfCounter64read-onlycurrent
f3L3TrafficIpInterfaceHistoryIcmpV6WONdpRx
OBJECT-TYPE
The number of packets Icmpv6 protocol recieved.
1.3.6.1.4.1.2544.1.12.37.2.5.1.16PerfCounter64read-onlycurrent
f3L3TrafficIpInterfaceHistoryNdpNSTx
OBJECT-TYPE
The number of transmit NS message.
1.3.6.1.4.1.2544.1.12.37.2.5.1.17PerfCounter64read-onlycurrent
f3L3TrafficIpInterfaceHistoryNdpNSRx
OBJECT-TYPE
The number of recieved NS message.
1.3.6.1.4.1.2544.1.12.37.2.5.1.18PerfCounter64read-onlycurrent
f3L3TrafficIpInterfaceHistoryNdpNATx
OBJECT-TYPE
The number of transmit NA message.
1.3.6.1.4.1.2544.1.12.37.2.5.1.19PerfCounter64read-onlycurrent
f3L3TrafficIpInterfaceHistoryNdpNARx
OBJECT-TYPE
The number of recieved NA message.
1.3.6.1.4.1.2544.1.12.37.2.5.1.20PerfCounter64read-onlycurrent
f3L3TrafficIpInterfaceHistoryNdpRATx
OBJECT-TYPE
The number of transmit RA message.
1.3.6.1.4.1.2544.1.12.37.2.5.1.21PerfCounter64read-onlycurrent
f3L3TrafficIpInterfaceHistoryNdpRARx
OBJECT-TYPE
The number of recieved RA message.
1.3.6.1.4.1.2544.1.12.37.2.5.1.22PerfCounter64read-onlycurrent
f3L3TrafficIpInterfaceHistoryNdpRSTx
OBJECT-TYPE
The number of transmit RS message.
1.3.6.1.4.1.2544.1.12.37.2.5.1.23PerfCounter64read-onlycurrent
f3L3TrafficIpInterfaceHistoryNdpRSRx
OBJECT-TYPE
The number of recieved RS message.
1.3.6.1.4.1.2544.1.12.37.2.5.1.24PerfCounter64read-onlycurrent
f3L3TrafficIpInterfaceThresholdTable
OBJECT-TYPE
A table of entries that allow manageability of L3 traffic ip interface Thresholds.
1.3.6.1.4.1.2544.1.12.37.2.6not-accessiblecurrent
f3L3TrafficIpInterfaceThresholdEntry
OBJECT-TYPE
A conceptual row in the f3L3TrafficIpInterfaceThresholdTable.
1.3.6.1.4.1.2544.1.12.37.2.6.1not-accessiblecurrent
f3L3TrafficIpInterfaceThresholdIndex
OBJECT-TYPE
An index that uniquely identifies an entry in the f3L3TrafficIpInterfaceThresholdTable.
1.3.6.1.4.1.2544.1.12.37.2.6.1.1Integer32 (1..65535)read-onlycurrent
f3L3TrafficIpInterfaceThresholdInterval
OBJECT-TYPE
The interval over which monitored value is sampled and compared with the specified threshold.
1.3.6.1.4.1.2544.1.12.37.2.6.1.2CmPmIntervalTyperead-onlycurrent
f3L3TrafficIpInterfaceThresholdVariable
OBJECT-TYPE
The object identifier of the particular variable to be sampled.
1.3.6.1.4.1.2544.1.12.37.2.6.1.3VariablePointerread-onlycurrent
f3L3TrafficIpInterfaceThresholdValueLo
OBJECT-TYPE
Lower 32 bits of the threshold value.
1.3.6.1.4.1.2544.1.12.37.2.6.1.4Unsigned32read-writecurrent
f3L3TrafficIpInterfaceThresholdValueHi
OBJECT-TYPE
Higher 32 bits of the threshold value.
1.3.6.1.4.1.2544.1.12.37.2.6.1.5Unsigned32read-writecurrent
f3L3TrafficIpInterfaceThresholdMonValue
OBJECT-TYPE
Monitored value corresponding to f3L3TrafficIpInterfaceThresholdVariable.
1.3.6.1.4.1.2544.1.12.37.2.6.1.6Counter64read-onlycurrent
f3L3AclRuleStatsTable
OBJECT-TYPE
A collection of L3 acl rule related statistics. These reflect the current data.
1.3.6.1.4.1.2544.1.12.37.2.7not-accessiblecurrent
f3L3AclRuleStatsEntry
OBJECT-TYPE
A conceptual row in the f3L3AclRuleStatsTable. Entries exist in this table for each Acl rule.
1.3.6.1.4.1.2544.1.12.37.2.7.1not-accessiblecurrent
f3L3AclRuleStatsIndex
OBJECT-TYPE
An arbitrary integer index value used to uniquely identify this L3 flow point statistics entry. 1 - 15min 2 - 1day 3 - rollover 4 - 5min
1.3.6.1.4.1.2544.1.12.37.2.7.1.1Integer32 (1..4)read-onlycurrent
f3L3AclRuleStatsIntervalType
OBJECT-TYPE
Interval over which Performance Monitoring data is collected.
1.3.6.1.4.1.2544.1.12.37.2.7.1.2CmPmIntervalTyperead-onlycurrent
f3L3AclRuleStatsValid
OBJECT-TYPE
Indicates the validity of the bin.
1.3.6.1.4.1.2544.1.12.37.2.7.1.3TruthValueread-onlycurrent
f3L3AclRuleStatsAction
OBJECT-TYPE
Allows the Manager to clear the bin.
1.3.6.1.4.1.2544.1.12.37.2.7.1.4CmPmBinActionread-writecurrent
f3L3AclRuleStatsRuleMatch
OBJECT-TYPE
The number of packets matching the ACL rule.
1.3.6.1.4.1.2544.1.12.37.2.7.1.5PerfCounter64read-onlycurrent
f3L3AclRuleHistoryTable
OBJECT-TYPE
A collection of L3 acl rule related history statistics. These reflect the history data.
1.3.6.1.4.1.2544.1.12.37.2.8not-accessiblecurrent
f3L3AclRuleHistoryEntry
OBJECT-TYPE
A conceptual row in the f3L3AclRuleHistoryTable. Entries exist in this table for each L3 acl rule.
1.3.6.1.4.1.2544.1.12.37.2.8.1not-accessiblecurrent
f3L3AclRuleHistoryIndex
OBJECT-TYPE
An arbitrary integer index value used to uniquely identify the history bin.
1.3.6.1.4.1.2544.1.12.37.2.8.1.1Integer32 (1..65535)read-onlycurrent
f3L3AclRuleHistoryTime
OBJECT-TYPE
Indicates the time of history bin creation.
1.3.6.1.4.1.2544.1.12.37.2.8.1.2DateAndTimeread-onlycurrent
f3L3AclRuleHistoryValid
OBJECT-TYPE
Indicates the validity of the bin.
1.3.6.1.4.1.2544.1.12.37.2.8.1.3TruthValueread-onlycurrent
f3L3AclRuleHistoryAction
OBJECT-TYPE
Allows the Manager to clear the bin.
1.3.6.1.4.1.2544.1.12.37.2.8.1.4CmPmBinActionread-writecurrent
f3L3AclRuleHistoryRuleMatch
OBJECT-TYPE
The number of packets matching acl rule.
1.3.6.1.4.1.2544.1.12.37.2.8.1.5PerfCounter64read-onlycurrent
f3L3AclRuleThresholdTable
OBJECT-TYPE
A table of entries that allow manageability of L3 acl rule Thresholds.
1.3.6.1.4.1.2544.1.12.37.2.9not-accessiblecurrent
f3L3AclRuleThresholdEntry
OBJECT-TYPE
A conceptual row in the f3L3AclRuleThresholdTable.
1.3.6.1.4.1.2544.1.12.37.2.9.1not-accessiblecurrent
f3L3AclRuleThresholdIndex
OBJECT-TYPE
An index that uniquely identifies an entry in the f3L3AclRuleThresholdTable.
1.3.6.1.4.1.2544.1.12.37.2.9.1.1Integer32 (1..65535)read-onlycurrent
f3L3AclRuleThresholdInterval
OBJECT-TYPE
The interval over which monitored value is sampled and compared with the specified threshold.
1.3.6.1.4.1.2544.1.12.37.2.9.1.2CmPmIntervalTyperead-onlycurrent
f3L3AclRuleThresholdVariable
OBJECT-TYPE
The object identifier of the particular variable to be sampled.
1.3.6.1.4.1.2544.1.12.37.2.9.1.3VariablePointerread-onlycurrent
f3L3AclRuleThresholdValueLo
OBJECT-TYPE
Lower 32 bits of the threshold value.
1.3.6.1.4.1.2544.1.12.37.2.9.1.4Unsigned32read-writecurrent
f3L3AclRuleThresholdValueHi
OBJECT-TYPE
Higher 32 bits of the threshold value.
1.3.6.1.4.1.2544.1.12.37.2.9.1.5Unsigned32read-writecurrent
f3L3AclRuleThresholdMonValue
OBJECT-TYPE
Monitored value corresponding to f3L3AclRuleThresholdVariable.
1.3.6.1.4.1.2544.1.12.37.2.9.1.6Counter64read-onlycurrent
f3L3QosPolicerStatsTable
OBJECT-TYPE
A collection of QOS Policer statistics. These reflect the current data.
1.3.6.1.4.1.2544.1.12.37.2.10not-accessiblecurrent
f3L3QosPolicerStatsEntry
OBJECT-TYPE
A conceptual row in the f3L3QosPolicerStatsTable. Entries exist in this table for each l3 flow point policer.
1.3.6.1.4.1.2544.1.12.37.2.10.1not-accessiblecurrent
f3L3QosPolicerStatsIndex
OBJECT-TYPE
An integer index value used to uniquely identify this QOS Policer statistics entry. 1 - 15min 2 - 1day 3 - rollover 4 - 5min
1.3.6.1.4.1.2544.1.12.37.2.10.1.1Integer32 (1..65535)read-onlycurrent
f3L3QosPolicerStatsIntervalType
OBJECT-TYPE
Interval over which Performance Monitoring data is collected.
1.3.6.1.4.1.2544.1.12.37.2.10.1.2CmPmIntervalTyperead-onlycurrent
f3L3QosPolicerStatsValid
OBJECT-TYPE
Indicates the validity of the bin.
1.3.6.1.4.1.2544.1.12.37.2.10.1.3TruthValueread-onlycurrent
f3L3QosPolicerStatsAction
OBJECT-TYPE
Allows the Manager to clear the bin.
1.3.6.1.4.1.2544.1.12.37.2.10.1.4CmPmBinActionread-writecurrent
f3L3QosPolicerStatsFMG
OBJECT-TYPE
Frames Marked Green.
1.3.6.1.4.1.2544.1.12.37.2.10.1.5PerfCounter64read-onlycurrent
f3L3QosPolicerStatsFMY
OBJECT-TYPE
Frames Marked Yellow.
1.3.6.1.4.1.2544.1.12.37.2.10.1.6PerfCounter64read-onlycurrent
f3L3QosPolicerStatsFMYD
OBJECT-TYPE
Frames Marked Yellow and Dropped.
1.3.6.1.4.1.2544.1.12.37.2.10.1.7PerfCounter64read-onlydeprecated
f3L3QosPolicerStatsFMRD
OBJECT-TYPE
Frames Marked Red and Discarded.
1.3.6.1.4.1.2544.1.12.37.2.10.1.8PerfCounter64read-onlycurrent
f3L3QosPolicerStatsBytesIn
OBJECT-TYPE
Number of bytes received by the Policer.
1.3.6.1.4.1.2544.1.12.37.2.10.1.9PerfCounter64read-onlycurrent
f3L3QosPolicerStatsBytesOut
OBJECT-TYPE
Number of bytes transmitted by the Policer.
1.3.6.1.4.1.2544.1.12.37.2.10.1.10PerfCounter64read-onlycurrent
f3L3QosPolicerStatsABR
OBJECT-TYPE
Average Bit Rate on the Policer.
1.3.6.1.4.1.2544.1.12.37.2.10.1.11PerfCounter64read-onlycurrent
f3L3QosPolicerHistoryTable
OBJECT-TYPE
A collection of QOS Policer statistics. These reflect the current data.
1.3.6.1.4.1.2544.1.12.37.2.11not-accessiblecurrent
f3L3QosPolicerHistoryEntry
OBJECT-TYPE
A conceptual row in the f3L3QosPolicerHistoryTable. Entries exist in this table for each flow point policer.
1.3.6.1.4.1.2544.1.12.37.2.11.1not-accessiblecurrent
f3L3QosPolicerHistoryIndex
OBJECT-TYPE
An arbitrary integer index value used to uniquely identify this QOS Policer history entry.
1.3.6.1.4.1.2544.1.12.37.2.11.1.1Integer32 (1..65535)read-onlycurrent
f3L3QosPolicerHistoryTime
OBJECT-TYPE
Indicates the time of history bin creation.
1.3.6.1.4.1.2544.1.12.37.2.11.1.2DateAndTimeread-onlycurrent
f3L3QosPolicerHistoryValid
OBJECT-TYPE
Indicates the validity of the bin.
1.3.6.1.4.1.2544.1.12.37.2.11.1.3TruthValueread-onlycurrent
f3L3QosPolicerHistoryAction
OBJECT-TYPE
Allows the Manager to clear the bin.
1.3.6.1.4.1.2544.1.12.37.2.11.1.4CmPmBinActionread-writecurrent
f3L3QosPolicerHistoryFMG
OBJECT-TYPE
Frames Marked Green.
1.3.6.1.4.1.2544.1.12.37.2.11.1.5PerfCounter64read-onlycurrent
f3L3QosPolicerHistoryFMY
OBJECT-TYPE
Frames Marked Yellow.
1.3.6.1.4.1.2544.1.12.37.2.11.1.6PerfCounter64read-onlycurrent
f3L3QosPolicerHistoryFMYD
OBJECT-TYPE
Frames Marked Yellow and Dropped.
1.3.6.1.4.1.2544.1.12.37.2.11.1.7PerfCounter64read-onlydeprecated
f3L3QosPolicerHistoryFMRD
OBJECT-TYPE
Frames Marked Red and Discarded.
1.3.6.1.4.1.2544.1.12.37.2.11.1.8PerfCounter64read-onlycurrent
f3L3QosPolicerHistoryBytesIn
OBJECT-TYPE
Number of bytes received by the Policer.
1.3.6.1.4.1.2544.1.12.37.2.11.1.9PerfCounter64read-onlycurrent
f3L3QosPolicerHistoryBytesOut
OBJECT-TYPE
Number of bytes transmitted by the Policer.
1.3.6.1.4.1.2544.1.12.37.2.11.1.10PerfCounter64read-onlycurrent
f3L3QosPolicerHistoryABR
OBJECT-TYPE
Average Bit Rate on the Policer.
1.3.6.1.4.1.2544.1.12.37.2.11.1.11PerfCounter64read-onlycurrent
f3L3QosPolicerThresholdTable
OBJECT-TYPE
A table of entries that allow manageability of QOS Policer Thresholds.
1.3.6.1.4.1.2544.1.12.37.2.12not-accessiblecurrent
f3L3QosPolicerThresholdEntry
OBJECT-TYPE
A conceptual row in the f3L3QosPolicerThresholdTable.
1.3.6.1.4.1.2544.1.12.37.2.12.1not-accessiblecurrent
f3L3QosPolicerThresholdIndex
OBJECT-TYPE
An index that uniquely identifies an entry in the f3L3QosPolicerThresholdTable.
1.3.6.1.4.1.2544.1.12.37.2.12.1.1Integer32 (1..65535)read-onlycurrent
f3L3QosPolicerThresholdInterval
OBJECT-TYPE
The interval over which monitored value is sampled and compared with the specified threshold.
1.3.6.1.4.1.2544.1.12.37.2.12.1.2CmPmIntervalTyperead-onlycurrent
f3L3QosPolicerThresholdVariable
OBJECT-TYPE
The object identifier of the particular variable to be sampled.
1.3.6.1.4.1.2544.1.12.37.2.12.1.3VariablePointerread-onlycurrent
f3L3QosPolicerThresholdValueLo
OBJECT-TYPE
Lower 32 bits of the threshold value.
1.3.6.1.4.1.2544.1.12.37.2.12.1.4Unsigned32read-writecurrent
f3L3QosPolicerThresholdValueHi
OBJECT-TYPE
Higher 32 bits of the threshold value.
1.3.6.1.4.1.2544.1.12.37.2.12.1.5Unsigned32read-writecurrent
f3L3QosPolicerThresholdMonValue
OBJECT-TYPE
Monitored value corresponding to f3L3QosPolicerThresholdVariable.
1.3.6.1.4.1.2544.1.12.37.2.12.1.6Counter64read-onlycurrent
f3L3QosShaperStatsTable
OBJECT-TYPE
A collection of L3 flow point Level QOS Shaper statistics. These reflect the current data.
1.3.6.1.4.1.2544.1.12.37.2.13not-accessiblecurrent
f3L3QosShaperStatsEntry
OBJECT-TYPE
A conceptual row in the f3L3QosShaperStatsTable. Entries exist in this table for each QOS Shaper per L3 flow point.
1.3.6.1.4.1.2544.1.12.37.2.13.1not-accessiblecurrent
f3L3QosShaperStatsIndex
OBJECT-TYPE
An arbitrary integer index value used to uniquely identify this QOS Shaper statistics entry. 1 - 15min 2 - 1day 3 - rollover 4 - 5min
1.3.6.1.4.1.2544.1.12.37.2.13.1.1Integer32 (1..65535)read-onlycurrent
f3L3QosShaperStatsIntervalType
OBJECT-TYPE
Interval over which Performance Monitoring data is collected.
1.3.6.1.4.1.2544.1.12.37.2.13.1.2CmPmIntervalTyperead-onlycurrent
f3L3QosShaperStatsValid
OBJECT-TYPE
Indicates the validity of the bin.
1.3.6.1.4.1.2544.1.12.37.2.13.1.3TruthValueread-onlycurrent
f3L3QosShaperStatsAction
OBJECT-TYPE
Allows the Manager to clear the bin.
1.3.6.1.4.1.2544.1.12.37.2.13.1.4CmPmBinActionread-writecurrent
f3L3QosShaperStatsBT
OBJECT-TYPE
Bytes Transmitted.
1.3.6.1.4.1.2544.1.12.37.2.13.1.5PerfCounter64read-onlycurrent
f3L3QosShaperStatsBTD
OBJECT-TYPE
Bytes Tail Dropped.
1.3.6.1.4.1.2544.1.12.37.2.13.1.6PerfCounter64read-onlycurrent
f3L3QosShaperStatsFD
OBJECT-TYPE
Frames Dequeued.
1.3.6.1.4.1.2544.1.12.37.2.13.1.7PerfCounter64read-onlycurrent
f3L3QosShaperStatsFTD
OBJECT-TYPE
Frames Tail Dropped.
1.3.6.1.4.1.2544.1.12.37.2.13.1.8PerfCounter64read-onlycurrent
f3L3QosShaperStatsBR
OBJECT-TYPE
Bytes Replicated.
1.3.6.1.4.1.2544.1.12.37.2.13.1.9PerfCounter64read-onlycurrent
f3L3QosShaperStatsFR
OBJECT-TYPE
Frames Replicated.
1.3.6.1.4.1.2544.1.12.37.2.13.1.10PerfCounter64read-onlycurrent
f3L3QosShaperStatsABRRL
OBJECT-TYPE
Average Bit Rate - Rate Limited.
1.3.6.1.4.1.2544.1.12.37.2.13.1.11PerfCounter64read-onlycurrent
f3L3QosShaperStatsABRRLR
OBJECT-TYPE
Average Bit Rate - Rate Limited, Replicated.
1.3.6.1.4.1.2544.1.12.37.2.13.1.12PerfCounter64read-onlycurrent
f3L3QosShaperStatsBREDD
OBJECT-TYPE
Bytes Random Early Discard, Dropped.
1.3.6.1.4.1.2544.1.12.37.2.13.1.13PerfCounter64read-onlycurrent
f3L3QosShaperStatsFREDD
OBJECT-TYPE
Frames Random Early Discard, Dropped.
1.3.6.1.4.1.2544.1.12.37.2.13.1.14PerfCounter64read-onlycurrent
f3L3QosShaperHistoryTable
OBJECT-TYPE
A collection of l3 flow point Level QOS Shaper statistics. These reflect the history data.
1.3.6.1.4.1.2544.1.12.37.2.14not-accessiblecurrent
f3L3QosShaperHistoryEntry
OBJECT-TYPE
A conceptual row in the f3L3QosShaperHistoryTable. Entries exist in this table for each Shaper per l3 flow point.
1.3.6.1.4.1.2544.1.12.37.2.14.1not-accessiblecurrent
f3L3QosShaperHistoryIndex
OBJECT-TYPE
An arbitrary integer index value used to uniquely identify this QOS Shaper statistics entry.
1.3.6.1.4.1.2544.1.12.37.2.14.1.1Integer32 (1..65535)read-onlycurrent
f3L3QosShaperHistoryTime
OBJECT-TYPE
Indicates the time of history bin creation.
1.3.6.1.4.1.2544.1.12.37.2.14.1.2DateAndTimeread-onlycurrent
f3L3QosShaperHistoryValid
OBJECT-TYPE
Indicates the validity of the bin.
1.3.6.1.4.1.2544.1.12.37.2.14.1.3TruthValueread-onlycurrent
f3L3QosShaperHistoryAction
OBJECT-TYPE
Allows the Manager to clear the bin.
1.3.6.1.4.1.2544.1.12.37.2.14.1.4CmPmBinActionread-writecurrent
f3L3QosShaperHistoryBT
OBJECT-TYPE
Bytes Transmitted.
1.3.6.1.4.1.2544.1.12.37.2.14.1.5PerfCounter64read-onlycurrent
f3L3QosShaperHistoryBTD
OBJECT-TYPE
Bytes Tail Dropped.
1.3.6.1.4.1.2544.1.12.37.2.14.1.6PerfCounter64read-onlycurrent
f3L3QosShaperHistoryFD
OBJECT-TYPE
Frames Dequeued.
1.3.6.1.4.1.2544.1.12.37.2.14.1.7PerfCounter64read-onlycurrent
f3L3QosShaperHistoryFTD
OBJECT-TYPE
Frames Tail Dropped.
1.3.6.1.4.1.2544.1.12.37.2.14.1.8PerfCounter64read-onlycurrent
f3L3QosShaperHistoryBR
OBJECT-TYPE
Bytes Replicated.
1.3.6.1.4.1.2544.1.12.37.2.14.1.9PerfCounter64read-onlycurrent
f3L3QosShaperHistoryFR
OBJECT-TYPE
Frames Replicated.
1.3.6.1.4.1.2544.1.12.37.2.14.1.10PerfCounter64read-onlycurrent
f3L3QosShaperHistoryABRRL
OBJECT-TYPE
Average Bit Rate - Rate Limited.
1.3.6.1.4.1.2544.1.12.37.2.14.1.11PerfCounter64read-onlycurrent
f3L3QosShaperHistoryABRRLR
OBJECT-TYPE
Average Bit Rate - Rate Limited, Replicated.
1.3.6.1.4.1.2544.1.12.37.2.14.1.12PerfCounter64read-onlycurrent
f3L3QosShaperHistoryBREDD
OBJECT-TYPE
Bytes Random Early Discard, Dropped.
1.3.6.1.4.1.2544.1.12.37.2.14.1.13PerfCounter64read-onlycurrent
f3L3QosShaperHistoryFREDD
OBJECT-TYPE
Frames Random Early Discard, Dropped.
1.3.6.1.4.1.2544.1.12.37.2.14.1.14PerfCounter64read-onlycurrent
f3L3QosShaperThresholdTable
OBJECT-TYPE
A table of entries that allow manageability of QOS Shaper Thresholds.
1.3.6.1.4.1.2544.1.12.37.2.15not-accessiblecurrent
f3L3QosShaperThresholdEntry
OBJECT-TYPE
A conceptual row in the f3L3QosShaperThresholdTable.
1.3.6.1.4.1.2544.1.12.37.2.15.1not-accessiblecurrent
f3L3QosShaperThresholdIndex
OBJECT-TYPE
An index that uniquely identifies an entry in the f3L3QosShaperThresholdTable.
1.3.6.1.4.1.2544.1.12.37.2.15.1.1Integer32 (1..65535)read-onlycurrent
f3L3QosShaperThresholdInterval
OBJECT-TYPE
The interval over which monitored value is sampled and compared with the specified threshold.
1.3.6.1.4.1.2544.1.12.37.2.15.1.2CmPmIntervalTyperead-onlycurrent
f3L3QosShaperThresholdVariable
OBJECT-TYPE
The object identifier of the particular variable to be sampled.
1.3.6.1.4.1.2544.1.12.37.2.15.1.3VariablePointerread-onlycurrent
f3L3QosShaperThresholdValueLo
OBJECT-TYPE
Lower 32 bits of the threshold value.
1.3.6.1.4.1.2544.1.12.37.2.15.1.4Unsigned32read-writecurrent
f3L3QosShaperThresholdValueHi
OBJECT-TYPE
Higher 32 bits of the threshold value.
1.3.6.1.4.1.2544.1.12.37.2.15.1.5Unsigned32read-writecurrent
f3L3QosShaperThresholdMonValue
OBJECT-TYPE
Monitored value corresponding to f3L3QosShaperThresholdVariable.
1.3.6.1.4.1.2544.1.12.37.2.15.1.6Counter64read-onlycurrent
f3L2A2NAclRuleStatsTable
OBJECT-TYPE
A collection of L3 acl rule related statistics. These reflect the current data.
1.3.6.1.4.1.2544.1.12.37.2.16not-accessiblecurrent
f3L2A2NAclRuleStatsEntry
OBJECT-TYPE
A conceptual row in the f3L2A2NAclRuleStatsTable. Entries exist in this table for each Acl rule.
1.3.6.1.4.1.2544.1.12.37.2.16.1not-accessiblecurrent
f3L2A2NAclRuleStatsIndex
OBJECT-TYPE
An arbitrary integer index value used to uniquely identify this L3 flow point statistics entry. 1 - 15min 2 - 1day 3 - rollover 4 - 5min
1.3.6.1.4.1.2544.1.12.37.2.16.1.1Integer32 (1..4)read-onlycurrent
f3L2A2NAclRuleStatsIntervalType
OBJECT-TYPE
Interval over which Performance Monitoring data is collected.
1.3.6.1.4.1.2544.1.12.37.2.16.1.2CmPmIntervalTyperead-onlycurrent
f3L2A2NAclRuleStatsValid
OBJECT-TYPE
Indicates the validity of the bin.
1.3.6.1.4.1.2544.1.12.37.2.16.1.3TruthValueread-onlycurrent
f3L2A2NAclRuleStatsAction
OBJECT-TYPE
Allows the Manager to clear the bin.
1.3.6.1.4.1.2544.1.12.37.2.16.1.4CmPmBinActionread-writecurrent
f3L2A2NAclRuleStatsRuleMatch
OBJECT-TYPE
The number of packets matching the ACL rule.
1.3.6.1.4.1.2544.1.12.37.2.16.1.5PerfCounter64read-onlycurrent
f3L2A2NAclRuleHistoryTable
OBJECT-TYPE
A collection of L3 acl rule related history statistics. These reflect the history data.
1.3.6.1.4.1.2544.1.12.37.2.17not-accessiblecurrent
f3L2A2NAclRuleHistoryEntry
OBJECT-TYPE
A conceptual row in the f3L2A2NAclRuleHistoryTable. Entries exist in this table for each L3 acl rule.
1.3.6.1.4.1.2544.1.12.37.2.17.1not-accessiblecurrent
f3L2A2NAclRuleHistoryIndex
OBJECT-TYPE
An arbitrary integer index value used to uniquely identify this L3 flow point statistics entry. 1 - 15min 2 - 1day 3 - rollover 4 - 5min
1.3.6.1.4.1.2544.1.12.37.2.17.1.1Integer32 (1..65535)read-onlycurrent
f3L2A2NAclRuleHistoryTime
OBJECT-TYPE
Indicates the time of history bin creation.
1.3.6.1.4.1.2544.1.12.37.2.17.1.2DateAndTimeread-onlycurrent
f3L2A2NAclRuleHistoryValid
OBJECT-TYPE
Indicates the validity of the bin.
1.3.6.1.4.1.2544.1.12.37.2.17.1.3TruthValueread-onlycurrent
f3L2A2NAclRuleHistoryAction
OBJECT-TYPE
Allows the Manager to clear the bin.
1.3.6.1.4.1.2544.1.12.37.2.17.1.4CmPmBinActionread-writecurrent
f3L2A2NAclRuleHistoryRuleMatch
OBJECT-TYPE
The number of packets matching acl rule.
1.3.6.1.4.1.2544.1.12.37.2.17.1.5PerfCounter64read-onlycurrent
f3L2A2NAclRuleThresholdTable
OBJECT-TYPE
A table of entries that allow manageability of L3 acl rule Thresholds.
1.3.6.1.4.1.2544.1.12.37.2.18not-accessiblecurrent
f3L2A2NAclRuleThresholdEntry
OBJECT-TYPE
A conceptual row in the f3L2A2NAclRuleThresholdTable.
1.3.6.1.4.1.2544.1.12.37.2.18.1not-accessiblecurrent
f3L2A2NAclRuleThresholdIndex
OBJECT-TYPE
An index that uniquely identifies an entry in the f3L2A2NAclRuleThresholdTable.
1.3.6.1.4.1.2544.1.12.37.2.18.1.1Integer32 (1..65535)read-onlycurrent
f3L2A2NAclRuleThresholdInterval
OBJECT-TYPE
The interval over which monitored value is sampled and compared with the specified threshold.
1.3.6.1.4.1.2544.1.12.37.2.18.1.2CmPmIntervalTyperead-onlycurrent
f3L2A2NAclRuleThresholdVariable
OBJECT-TYPE
The object identifier of the particular variable to be sampled.
1.3.6.1.4.1.2544.1.12.37.2.18.1.3VariablePointerread-onlycurrent
f3L2A2NAclRuleThresholdValueLo
OBJECT-TYPE
Lower 32 bits of the threshold value.
1.3.6.1.4.1.2544.1.12.37.2.18.1.4Unsigned32read-writecurrent
f3L2A2NAclRuleThresholdValueHi
OBJECT-TYPE
Higher 32 bits of the threshold value.
1.3.6.1.4.1.2544.1.12.37.2.18.1.5Unsigned32read-writecurrent
f3L2A2NAclRuleThresholdMonValue
OBJECT-TYPE
Monitored value corresponding to f3L2A2NAclRuleThresholdVariable.
1.3.6.1.4.1.2544.1.12.37.2.18.1.6Counter64read-onlycurrent
f3L2N2AAclRuleStatsTable
OBJECT-TYPE
A collection of L3 acl rule related statistics. These reflect the current data.
1.3.6.1.4.1.2544.1.12.37.2.19not-accessiblecurrent
f3L2N2AAclRuleStatsEntry
OBJECT-TYPE
A conceptual row in the f3L2N2AAclRuleStatsTable. Entries exist in this table for each Acl rule.
1.3.6.1.4.1.2544.1.12.37.2.19.1not-accessiblecurrent
f3L2N2AAclRuleStatsIndex
OBJECT-TYPE
An arbitrary integer index value used to uniquely identify this L3 flow point statistics entry. 1 - 15min 2 - 1day 3 - rollover 4 - 5min
1.3.6.1.4.1.2544.1.12.37.2.19.1.1Integer32 (1..4)read-onlycurrent
f3L2N2AAclRuleStatsIntervalType
OBJECT-TYPE
Interval over which Performance Monitoring data is collected.
1.3.6.1.4.1.2544.1.12.37.2.19.1.2CmPmIntervalTyperead-onlycurrent
f3L2N2AAclRuleStatsValid
OBJECT-TYPE
Indicates the validity of the bin.
1.3.6.1.4.1.2544.1.12.37.2.19.1.3TruthValueread-onlycurrent
f3L2N2AAclRuleStatsAction
OBJECT-TYPE
Allows the Manager to clear the bin.
1.3.6.1.4.1.2544.1.12.37.2.19.1.4CmPmBinActionread-writecurrent
f3L2N2AAclRuleStatsRuleMatch
OBJECT-TYPE
The number of packets matching the ACL rule.
1.3.6.1.4.1.2544.1.12.37.2.19.1.5PerfCounter64read-onlycurrent
f3L2N2AAclRuleHistoryTable
OBJECT-TYPE
A collection of L3 acl rule related history statistics. These reflect the history data.
1.3.6.1.4.1.2544.1.12.37.2.20not-accessiblecurrent
f3L2N2AAclRuleHistoryEntry
OBJECT-TYPE
A conceptual row in the f3L2N2AAclRuleHistoryTable. Entries exist in this table for each L3 acl rule.
1.3.6.1.4.1.2544.1.12.37.2.20.1not-accessiblecurrent
f3L2N2AAclRuleHistoryIndex
OBJECT-TYPE
An arbitrary integer index value used to uniquely identify this L3 flow point statistics entry. 1 - 15min 2 - 1day 3 - rollover 4 - 5min
1.3.6.1.4.1.2544.1.12.37.2.20.1.1Integer32 (1..65535)read-onlycurrent
f3L2N2AAclRuleHistoryTime
OBJECT-TYPE
Indicates the time of history bin creation.
1.3.6.1.4.1.2544.1.12.37.2.20.1.2DateAndTimeread-onlycurrent
f3L2N2AAclRuleHistoryValid
OBJECT-TYPE
Indicates the validity of the bin.
1.3.6.1.4.1.2544.1.12.37.2.20.1.3TruthValueread-onlycurrent
f3L2N2AAclRuleHistoryAction
OBJECT-TYPE
Allows the Manager to clear the bin.
1.3.6.1.4.1.2544.1.12.37.2.20.1.4CmPmBinActionread-writecurrent
f3L2N2AAclRuleHistoryRuleMatch
OBJECT-TYPE
The number of packets matching acl rule.
1.3.6.1.4.1.2544.1.12.37.2.20.1.5PerfCounter64read-onlycurrent
f3L2N2AAclRuleThresholdTable
OBJECT-TYPE
A table of entries that allow manageability of L3 acl rule Thresholds.
1.3.6.1.4.1.2544.1.12.37.2.21not-accessiblecurrent
f3L2N2AAclRuleThresholdEntry
OBJECT-TYPE
A conceptual row in the f3L2N2AAclRuleThresholdTable.
1.3.6.1.4.1.2544.1.12.37.2.21.1not-accessiblecurrent
f3L2N2AAclRuleThresholdIndex
OBJECT-TYPE
An index that uniquely identifies an entry in the f3L2N2AAclRuleThresholdTable.
1.3.6.1.4.1.2544.1.12.37.2.21.1.1Integer32 (1..65535)read-onlycurrent
f3L2N2AAclRuleThresholdInterval
OBJECT-TYPE
The interval over which monitored value is sampled and compared with the specified threshold.
1.3.6.1.4.1.2544.1.12.37.2.21.1.2CmPmIntervalTyperead-onlycurrent
f3L2N2AAclRuleThresholdVariable
OBJECT-TYPE
The object identifier of the particular variable to be sampled.
1.3.6.1.4.1.2544.1.12.37.2.21.1.3VariablePointerread-onlycurrent
f3L2N2AAclRuleThresholdValueLo
OBJECT-TYPE
Lower 32 bits of the threshold value.
1.3.6.1.4.1.2544.1.12.37.2.21.1.4Unsigned32read-writecurrent
f3L2N2AAclRuleThresholdValueHi
OBJECT-TYPE
Higher 32 bits of the threshold value.
1.3.6.1.4.1.2544.1.12.37.2.21.1.5Unsigned32read-writecurrent
f3L2N2AAclRuleThresholdMonValue
OBJECT-TYPE
Monitored value corresponding to f3L2N2AAclRuleThresholdVariable.
1.3.6.1.4.1.2544.1.12.37.2.21.1.6Counter64read-onlycurrent
f3L3TrafficIPv6InterfaceStatsTable
OBJECT-TYPE
A collection of L3 traffic ipv6 interface related statistics. These reflect the current data.
1.3.6.1.4.1.2544.1.12.37.2.22not-accessiblecurrent
f3L3TrafficIPv6InterfaceStatsEntry
OBJECT-TYPE
A conceptual row in the f3L3TrafficIPv6InterfaceStatsTable. Entries exist in this table for each L3 traffic ipv6 interface.
1.3.6.1.4.1.2544.1.12.37.2.22.1not-accessiblecurrent
f3L3TrafficIPv6InterfaceStatsIndex
OBJECT-TYPE
An arbitrary integer index value used to uniquely identify this L3 Traffic IPv6 interface statistics entry. 1 - 15min 2 - 1day 3 - rollover 4 - 5min
1.3.6.1.4.1.2544.1.12.37.2.22.1.1Integer32 (1..4)read-onlycurrent
f3L3TrafficIPv6InterfaceStatsIntervalType
OBJECT-TYPE
Interval over which Performance Monitoring data is collected.
1.3.6.1.4.1.2544.1.12.37.2.22.1.2CmPmIntervalTyperead-onlycurrent
f3L3TrafficIPv6InterfaceStatsValid
OBJECT-TYPE
Indicates the validity of the bin.
1.3.6.1.4.1.2544.1.12.37.2.22.1.3TruthValueread-onlycurrent
f3L3TrafficIPv6InterfaceStatsAction
OBJECT-TYPE
Allows the Manager to clear the bin.
1.3.6.1.4.1.2544.1.12.37.2.22.1.4CmPmBinActionread-writecurrent
f3L3TrafficIPv6InterfaceStatsDhcpV6Tx
OBJECT-TYPE
.
1.3.6.1.4.1.2544.1.12.37.2.22.1.5PerfCounter64read-onlycurrent
f3L3TrafficIPv6InterfaceStatsDhcpV6Rx
OBJECT-TYPE
.
1.3.6.1.4.1.2544.1.12.37.2.22.1.6PerfCounter64read-onlycurrent
f3L3TrafficIPv6InterfaceStatsIcmpV6WONdpTx
OBJECT-TYPE
.
1.3.6.1.4.1.2544.1.12.37.2.22.1.7PerfCounter64read-onlycurrent
f3L3TrafficIPv6InterfaceStatsIcmpV6WONdpRx
OBJECT-TYPE
.
1.3.6.1.4.1.2544.1.12.37.2.22.1.8PerfCounter64read-onlycurrent
f3L3TrafficIPv6InterfaceStatsNdpNSTx
OBJECT-TYPE
.
1.3.6.1.4.1.2544.1.12.37.2.22.1.9PerfCounter64read-onlycurrent
f3L3TrafficIPv6InterfaceStatsNdpNSRx
OBJECT-TYPE
.
1.3.6.1.4.1.2544.1.12.37.2.22.1.10PerfCounter64read-onlycurrent
f3L3TrafficIPv6InterfaceStatsNdpNATx
OBJECT-TYPE
.
1.3.6.1.4.1.2544.1.12.37.2.22.1.11PerfCounter64read-onlycurrent
f3L3TrafficIPv6InterfaceStatsNdpNARx
OBJECT-TYPE
.
1.3.6.1.4.1.2544.1.12.37.2.22.1.12PerfCounter64read-onlycurrent
f3L3TrafficIPv6InterfaceStatsNdpRATx
OBJECT-TYPE
.
1.3.6.1.4.1.2544.1.12.37.2.22.1.13PerfCounter64read-onlycurrent
f3L3TrafficIPv6InterfaceStatsNdpRARx
OBJECT-TYPE
.
1.3.6.1.4.1.2544.1.12.37.2.22.1.14PerfCounter64read-onlycurrent
f3L3TrafficIPv6InterfaceStatsNdpRSTx
OBJECT-TYPE
.
1.3.6.1.4.1.2544.1.12.37.2.22.1.15PerfCounter64read-onlycurrent
f3L3TrafficIPv6InterfaceStatsNdpRSRx
OBJECT-TYPE
.
1.3.6.1.4.1.2544.1.12.37.2.22.1.16PerfCounter64read-onlycurrent
f3L3TrafficIPv6InterfaceHistoryTable
OBJECT-TYPE
A collection of L3 traffic ipv6 interface related statistics. These reflect the current data.
1.3.6.1.4.1.2544.1.12.37.2.23not-accessiblecurrent
f3L3TrafficIPv6InterfaceHistoryEntry
OBJECT-TYPE
A conceptual row in the f3L3TrafficIPv6InterfaceHistoryTable. Entries exist in this table for each L3 traffic ipv6 interface.
1.3.6.1.4.1.2544.1.12.37.2.23.1not-accessiblecurrent
f3L3TrafficIPv6InterfaceHistoryIndex
OBJECT-TYPE
An arbitrary integer index value used to uniquely identify this L3 Traffic IPv6 interface statistics entry. 1 - 15min 2 - 1day 3 - rollover 4 - 5min
1.3.6.1.4.1.2544.1.12.37.2.23.1.1Integer32 (1..4)read-onlycurrent
f3L3TrafficIPv6InterfaceHistoryTime
OBJECT-TYPE
Indicates the time of history bin creation.
1.3.6.1.4.1.2544.1.12.37.2.23.1.2DateAndTimeread-onlycurrent
f3L3TrafficIPv6InterfaceHistoryValid
OBJECT-TYPE
Indicates the validity of the bin.
1.3.6.1.4.1.2544.1.12.37.2.23.1.3TruthValueread-onlycurrent
f3L3TrafficIPv6InterfaceHistoryAction
OBJECT-TYPE
Allows the Manager to clear the bin.
1.3.6.1.4.1.2544.1.12.37.2.23.1.4CmPmBinActionread-writecurrent
f3L3TrafficIPv6InterfaceHistoryDhcpV6Tx
OBJECT-TYPE
.
1.3.6.1.4.1.2544.1.12.37.2.23.1.5PerfCounter64read-onlycurrent
f3L3TrafficIPv6InterfaceHistoryDhcpV6Rx
OBJECT-TYPE
.
1.3.6.1.4.1.2544.1.12.37.2.23.1.6PerfCounter64read-onlycurrent
f3L3TrafficIPv6InterfaceHistoryIcmpV6WONdpTx
OBJECT-TYPE
.
1.3.6.1.4.1.2544.1.12.37.2.23.1.7PerfCounter64read-onlycurrent
f3L3TrafficIPv6InterfaceHistoryIcmpV6WONdpRx
OBJECT-TYPE
.
1.3.6.1.4.1.2544.1.12.37.2.23.1.8PerfCounter64read-onlycurrent
f3L3TrafficIPv6InterfaceHistoryNdpNSTx
OBJECT-TYPE
.
1.3.6.1.4.1.2544.1.12.37.2.23.1.9PerfCounter64read-onlycurrent
f3L3TrafficIPv6InterfaceHistoryNdpNSRx
OBJECT-TYPE
.
1.3.6.1.4.1.2544.1.12.37.2.23.1.10PerfCounter64read-onlycurrent
f3L3TrafficIPv6InterfaceHistoryNdpNATx
OBJECT-TYPE
.
1.3.6.1.4.1.2544.1.12.37.2.23.1.11PerfCounter64read-onlycurrent
f3L3TrafficIPv6InterfaceHistoryNdpNARx
OBJECT-TYPE
.
1.3.6.1.4.1.2544.1.12.37.2.23.1.12PerfCounter64read-onlycurrent
f3L3TrafficIPv6InterfaceHistoryNdpRATx
OBJECT-TYPE
.
1.3.6.1.4.1.2544.1.12.37.2.23.1.13PerfCounter64read-onlycurrent
f3L3TrafficIPv6InterfaceHistoryNdpRARx
OBJECT-TYPE
.
1.3.6.1.4.1.2544.1.12.37.2.23.1.14PerfCounter64read-onlycurrent
f3L3TrafficIPv6InterfaceHistoryNdpRSTx
OBJECT-TYPE
.
1.3.6.1.4.1.2544.1.12.37.2.23.1.15PerfCounter64read-onlycurrent
f3L3TrafficIPv6InterfaceHistoryNdpRSRx
OBJECT-TYPE
.
1.3.6.1.4.1.2544.1.12.37.2.23.1.16PerfCounter64read-onlycurrent
f3L3TrafficIPv6InterfaceThresholdTable
OBJECT-TYPE
A table of entries that allow manageability of L3 traffic ipv6 interface Thresholds.
1.3.6.1.4.1.2544.1.12.37.2.24not-accessiblecurrent
f3L3TrafficIPv6InterfaceThresholdEntry
OBJECT-TYPE
A conceptual row in the f3L3TrafficIPv6InterfaceThresholdTable.
1.3.6.1.4.1.2544.1.12.37.2.24.1not-accessiblecurrent
f3L3TrafficIPv6InterfaceThresholdIndex
OBJECT-TYPE
An index that uniquely identifies an entry in the f3L3TrafficIPv6InterfaceThresholdTable.
1.3.6.1.4.1.2544.1.12.37.2.24.1.1Integer32 (1..65535)read-onlycurrent
f3L3TrafficIPv6InterfaceThresholdInterval
OBJECT-TYPE
The interval over which monitored value is sampled and compared with the specified threshold.
1.3.6.1.4.1.2544.1.12.37.2.24.1.2CmPmIntervalTyperead-onlycurrent
f3L3TrafficIPv6InterfaceThresholdVariable
OBJECT-TYPE
The object identifier of the particular variable to be sampled.
1.3.6.1.4.1.2544.1.12.37.2.24.1.3VariablePointerread-onlycurrent
f3L3TrafficIPv6InterfaceThresholdValueLo
OBJECT-TYPE
Lower 32 bits of the threshold value.
1.3.6.1.4.1.2544.1.12.37.2.24.1.4Unsigned32read-writecurrent
f3L3TrafficIPv6InterfaceThresholdValueHi
OBJECT-TYPE
Higher 32 bits of the threshold value.
1.3.6.1.4.1.2544.1.12.37.2.24.1.5Unsigned32read-writecurrent
f3L3TrafficIPv6InterfaceThresholdMonValue
OBJECT-TYPE
Monitored value corresponding to f3L3TrafficIPv6InterfaceThresholdVariable.
1.3.6.1.4.1.2544.1.12.37.2.24.1.6Counter64read-onlycurrent
cmL3FlowPointStatsTable
OBJECT-TYPE
A collection of L3 Flow Point related statistics. These reflect the current data.
1.3.6.1.4.1.2544.1.12.37.2.25not-accessiblecurrent
cmL3FlowPointStatsEntry
OBJECT-TYPE
A conceptual row in the cmL3FlowPointStatsTable. Entries exist in this table for each L3 flow point.
1.3.6.1.4.1.2544.1.12.37.2.25.1not-accessiblecurrent
cmL3FlowPointStatsIndex
OBJECT-TYPE
An arbitrary integer index value used to uniquely identify this L3 flow point statistics entry. 1 - 15min 2 - 1day 3 - rollover 4 - 5min
1.3.6.1.4.1.2544.1.12.37.2.25.1.1Integer32 (1..4)read-onlycurrent
cmL3FlowPointStatsIntervalType
OBJECT-TYPE
Interval over which Performance Monitoring data is collected.
1.3.6.1.4.1.2544.1.12.37.2.25.1.2CmPmIntervalTyperead-onlycurrent
cmL3FlowPointStatsValid
OBJECT-TYPE
Indicates the validity of the bin.
1.3.6.1.4.1.2544.1.12.37.2.25.1.3TruthValueread-onlycurrent
cmL3FlowPointStatsAction
OBJECT-TYPE
Allows the Manager to clear the bin.
1.3.6.1.4.1.2544.1.12.37.2.25.1.4CmPmBinActionread-writecurrent
cmL3FlowPointStatsFMG
OBJECT-TYPE
The number of Frames Marked Green.
1.3.6.1.4.1.2544.1.12.37.2.25.1.5PerfCounter64read-onlycurrent
cmL3FlowPointStatsFMY
OBJECT-TYPE
The number of Frames Marked Yellow.
1.3.6.1.4.1.2544.1.12.37.2.25.1.6PerfCounter64read-onlycurrent
cmL3FlowPointStatsFMRD
OBJECT-TYPE
The number of Frames Marked Red and Discarded.
1.3.6.1.4.1.2544.1.12.37.2.25.1.7PerfCounter64read-onlycurrent
cmL3FlowPointStatsFTD
OBJECT-TYPE
The number of Frames Tail Dropped.
1.3.6.1.4.1.2544.1.12.37.2.25.1.8PerfCounter64read-onlycurrent
cmL3FlowPointStatsFragmentedDropAcl
OBJECT-TYPE
The number of dropped fragmented packets.
1.3.6.1.4.1.2544.1.12.37.2.25.1.9PerfCounter64read-onlycurrent
cmL3FlowPointStatsAclRuleDrop
OBJECT-TYPE
The number of dropped packets due to ACL rule.
1.3.6.1.4.1.2544.1.12.37.2.25.1.10PerfCounter64read-onlycurrent
cmL3FlowPointStatsTtlEqual1Drop
OBJECT-TYPE
the number of dropped packets due to ttl's value is 1.
1.3.6.1.4.1.2544.1.12.37.2.25.1.11PerfCounter64read-onlycurrent
cmL3FlowPointStatsFrameTx
OBJECT-TYPE
The number of total transmitted frames.
1.3.6.1.4.1.2544.1.12.37.2.25.1.12PerfCounter64read-onlycurrent
cmL3FlowPointStatsFrameRx
OBJECT-TYPE
The number of total received frames.
1.3.6.1.4.1.2544.1.12.37.2.25.1.13PerfCounter64read-onlycurrent
cmL3FlowPointStatsNoRouteDrop
OBJECT-TYPE
The number of frames drop due to no route.
1.3.6.1.4.1.2544.1.12.37.2.25.1.14PerfCounter64read-onlycurrent
cmL3FlowPointStatsAclDropNoMatch
OBJECT-TYPE
The number of dropped packets due to no match in ACL rule.
1.3.6.1.4.1.2544.1.12.37.2.25.1.15PerfCounter64read-onlycurrent
cmL3FlowPointHistoryTable
OBJECT-TYPE
A collection of L3 Flow Point related statistics. These reflect the current data.
1.3.6.1.4.1.2544.1.12.37.2.26not-accessiblecurrent
cmL3FlowPointHistoryEntry
OBJECT-TYPE
A conceptual row in the cmL3FlowPointHistoryTable. Entries exist in this table for each L3 flow point.
1.3.6.1.4.1.2544.1.12.37.2.26.1not-accessiblecurrent
cmL3FlowPointHistoryIndex
OBJECT-TYPE
An arbitrary integer index value used to uniquely identify the history bin.
1.3.6.1.4.1.2544.1.12.37.2.26.1.1Integer32 (1..65535)read-onlycurrent
cmL3FlowPointHistoryTime
OBJECT-TYPE
Indicates the time of history bin creation.
1.3.6.1.4.1.2544.1.12.37.2.26.1.2DateAndTimeread-onlycurrent
cmL3FlowPointHistoryValid
OBJECT-TYPE
Indicates the validity of the bin.
1.3.6.1.4.1.2544.1.12.37.2.26.1.3TruthValueread-onlycurrent
cmL3FlowPointHistoryAction
OBJECT-TYPE
Allows the Manager to clear the bin.
1.3.6.1.4.1.2544.1.12.37.2.26.1.4CmPmBinActionread-writecurrent
cmL3FlowPointHistoryFMG
OBJECT-TYPE
The number of Frames Marked Green.
1.3.6.1.4.1.2544.1.12.37.2.26.1.5PerfCounter64read-onlycurrent
cmL3FlowPointHistoryFMY
OBJECT-TYPE
The number of Frames Marked Yellow.
1.3.6.1.4.1.2544.1.12.37.2.26.1.6PerfCounter64read-onlycurrent
cmL3FlowPointHistoryFMRD
OBJECT-TYPE
The number of Frames Marked Red and Discarded.
1.3.6.1.4.1.2544.1.12.37.2.26.1.7PerfCounter64read-onlycurrent
cmL3FlowPointHistoryFTD
OBJECT-TYPE
The number of Frames Tail Dropped.
1.3.6.1.4.1.2544.1.12.37.2.26.1.8PerfCounter64read-onlycurrent
cmL3FlowPointHistoryFragmentedDropAcl
OBJECT-TYPE
The number of dropped fragmented packets.
1.3.6.1.4.1.2544.1.12.37.2.26.1.9PerfCounter64read-onlycurrent
cmL3FlowPointHistoryAclRuleDrop
OBJECT-TYPE
The number of dropped packets due to ACL rule.
1.3.6.1.4.1.2544.1.12.37.2.26.1.10PerfCounter64read-onlycurrent
cmL3FlowPointHistoryTtlEqual1Drop
OBJECT-TYPE
the number of dropped packets due to ttl's value is 1.
1.3.6.1.4.1.2544.1.12.37.2.26.1.11PerfCounter64read-onlycurrent
cmL3FlowPointHistoryFrameTx
OBJECT-TYPE
The number of total transmitted frames.
1.3.6.1.4.1.2544.1.12.37.2.26.1.12PerfCounter64read-onlycurrent
cmL3FlowPointHistoryFrameRx
OBJECT-TYPE
the number of total recieved frames.
1.3.6.1.4.1.2544.1.12.37.2.26.1.13PerfCounter64read-onlycurrent
cmL3FlowPointHistoryNoRouteDrop
OBJECT-TYPE
the number of frames dropped due to no route.
1.3.6.1.4.1.2544.1.12.37.2.26.1.14PerfCounter64read-onlycurrent
cmL3FlowPointHistoryAclDropNoMatch
OBJECT-TYPE
The number of dropped packets due to no match in ACL rule.
1.3.6.1.4.1.2544.1.12.37.2.26.1.15PerfCounter64read-onlycurrent
cmL3FlowPointThresholdTable
OBJECT-TYPE
A table of entries that allow manageability of L3 Flow Point Thresholds.
1.3.6.1.4.1.2544.1.12.37.2.27not-accessiblecurrent
cmL3FlowPointThresholdEntry
OBJECT-TYPE
A conceptual row in the cmL3FlowPointThresholdTable.
1.3.6.1.4.1.2544.1.12.37.2.27.1not-accessiblecurrent
cmL3FlowPointThresholdIndex
OBJECT-TYPE
An index that uniquely identifies an entry in the cmL3FlowPointThresholdTable.
1.3.6.1.4.1.2544.1.12.37.2.27.1.1Integer32 (1..65535)read-onlycurrent
cmL3FlowPointThresholdInterval
OBJECT-TYPE
The interval over which monitored value is sampled and compared with the specified threshold.
1.3.6.1.4.1.2544.1.12.37.2.27.1.2CmPmIntervalTyperead-onlycurrent
cmL3FlowPointThresholdVariable
OBJECT-TYPE
The object identifier of the particular variable to be sampled.
1.3.6.1.4.1.2544.1.12.37.2.27.1.3VariablePointerread-onlycurrent
cmL3FlowPointThresholdValueLo
OBJECT-TYPE
Lower 32 bits of the threshold value.
1.3.6.1.4.1.2544.1.12.37.2.27.1.4Unsigned32read-writecurrent
cmL3FlowPointThresholdValueHi
OBJECT-TYPE
Higher 32 bits of the threshold value.
1.3.6.1.4.1.2544.1.12.37.2.27.1.5Unsigned32read-writecurrent
cmL3FlowPointThresholdMonValue
OBJECT-TYPE
Monitored value corresponding to cmL3FlowPointThresholdVariable.
1.3.6.1.4.1.2544.1.12.37.2.27.1.6Counter64read-onlycurrent
cmL3QosPolicerStatsTable
OBJECT-TYPE
A collection of QOS Policer statistics. These reflect the current data.
1.3.6.1.4.1.2544.1.12.37.2.28not-accessiblecurrent
cmL3QosPolicerStatsEntry
OBJECT-TYPE
A conceptual row in the cmL3QosPolicerStatsTable. Entries exist in this table for each l3 flow point policer.
1.3.6.1.4.1.2544.1.12.37.2.28.1not-accessiblecurrent
cmL3QosPolicerStatsIndex
OBJECT-TYPE
An integer index value used to uniquely identify this QOS Policer statistics entry. 1 - 15min 2 - 1day 3 - rollover 4 - 5min
1.3.6.1.4.1.2544.1.12.37.2.28.1.1Integer32 (1..65535)read-onlycurrent
cmL3QosPolicerStatsIntervalType
OBJECT-TYPE
Interval over which Performance Monitoring data is collected.
1.3.6.1.4.1.2544.1.12.37.2.28.1.2CmPmIntervalTyperead-onlycurrent
cmL3QosPolicerStatsValid
OBJECT-TYPE
Indicates the validity of the bin.
1.3.6.1.4.1.2544.1.12.37.2.28.1.3TruthValueread-onlycurrent
cmL3QosPolicerStatsAction
OBJECT-TYPE
Allows the Manager to clear the bin.
1.3.6.1.4.1.2544.1.12.37.2.28.1.4CmPmBinActionread-writecurrent
cmL3QosPolicerStatsFMG
OBJECT-TYPE
Frames Marked Green.
1.3.6.1.4.1.2544.1.12.37.2.28.1.5PerfCounter64read-onlycurrent
cmL3QosPolicerStatsFMY
OBJECT-TYPE
Frames Marked Yellow.
1.3.6.1.4.1.2544.1.12.37.2.28.1.6PerfCounter64read-onlycurrent
cmL3QosPolicerStatsFMYD
OBJECT-TYPE
Frames Marked Yellow and Dropped.
1.3.6.1.4.1.2544.1.12.37.2.28.1.7PerfCounter64read-onlydeprecated
cmL3QosPolicerStatsFMRD
OBJECT-TYPE
Frames Marked Red and Discarded.
1.3.6.1.4.1.2544.1.12.37.2.28.1.8PerfCounter64read-onlycurrent
cmL3QosPolicerStatsBytesIn
OBJECT-TYPE
Number of bytes received by the Policer.
1.3.6.1.4.1.2544.1.12.37.2.28.1.9PerfCounter64read-onlycurrent
cmL3QosPolicerStatsBytesOut
OBJECT-TYPE
Number of bytes transmitted by the Policer.
1.3.6.1.4.1.2544.1.12.37.2.28.1.10PerfCounter64read-onlycurrent
cmL3QosPolicerStatsABR
OBJECT-TYPE
Average Bit Rate on the Policer.
1.3.6.1.4.1.2544.1.12.37.2.28.1.11PerfCounter64read-onlycurrent
cmL3QosPolicerHistoryTable
OBJECT-TYPE
A collection of QOS Policer statistics. These reflect the current data.
1.3.6.1.4.1.2544.1.12.37.2.29not-accessiblecurrent
cmL3QosPolicerHistoryEntry
OBJECT-TYPE
A conceptual row in the cmL3QosPolicerHistoryTable. Entries exist in this table for each flow point policer.
1.3.6.1.4.1.2544.1.12.37.2.29.1not-accessiblecurrent
cmL3QosPolicerHistoryIndex
OBJECT-TYPE
An arbitrary integer index value used to uniquely identify this QOS Policer history entry.
1.3.6.1.4.1.2544.1.12.37.2.29.1.1Integer32 (1..65535)read-onlycurrent
cmL3QosPolicerHistoryTime
OBJECT-TYPE
Indicates the time of history bin creation.
1.3.6.1.4.1.2544.1.12.37.2.29.1.2DateAndTimeread-onlycurrent
cmL3QosPolicerHistoryValid
OBJECT-TYPE
Indicates the validity of the bin.
1.3.6.1.4.1.2544.1.12.37.2.29.1.3TruthValueread-onlycurrent
cmL3QosPolicerHistoryAction
OBJECT-TYPE
Allows the Manager to clear the bin.
1.3.6.1.4.1.2544.1.12.37.2.29.1.4CmPmBinActionread-writecurrent
cmL3QosPolicerHistoryFMG
OBJECT-TYPE
Frames Marked Green.
1.3.6.1.4.1.2544.1.12.37.2.29.1.5PerfCounter64read-onlycurrent
cmL3QosPolicerHistoryFMY
OBJECT-TYPE
Frames Marked Yellow.
1.3.6.1.4.1.2544.1.12.37.2.29.1.6PerfCounter64read-onlycurrent
cmL3QosPolicerHistoryFMYD
OBJECT-TYPE
Frames Marked Yellow and Dropped.
1.3.6.1.4.1.2544.1.12.37.2.29.1.7PerfCounter64read-onlydeprecated
cmL3QosPolicerHistoryFMRD
OBJECT-TYPE
Frames Marked Red and Discarded.
1.3.6.1.4.1.2544.1.12.37.2.29.1.8PerfCounter64read-onlycurrent
cmL3QosPolicerHistoryBytesIn
OBJECT-TYPE
Number of bytes received by the Policer.
1.3.6.1.4.1.2544.1.12.37.2.29.1.9PerfCounter64read-onlycurrent
cmL3QosPolicerHistoryBytesOut
OBJECT-TYPE
Number of bytes transmitted by the Policer.
1.3.6.1.4.1.2544.1.12.37.2.29.1.10PerfCounter64read-onlycurrent
cmL3QosPolicerHistoryABR
OBJECT-TYPE
Average Bit Rate on the Policer.
1.3.6.1.4.1.2544.1.12.37.2.29.1.11PerfCounter64read-onlycurrent
cmL3QosPolicerThresholdTable
OBJECT-TYPE
A table of entries that allow manageability of QOS Policer Thresholds.
1.3.6.1.4.1.2544.1.12.37.2.30not-accessiblecurrent
cmL3QosPolicerThresholdEntry
OBJECT-TYPE
A conceptual row in the cmL3QosPolicerThresholdTable.
1.3.6.1.4.1.2544.1.12.37.2.30.1not-accessiblecurrent
cmL3QosPolicerThresholdIndex
OBJECT-TYPE
An index that uniquely identifies an entry in the cmL3QosPolicerThresholdTable.
1.3.6.1.4.1.2544.1.12.37.2.30.1.1Integer32 (1..65535)read-onlycurrent
cmL3QosPolicerThresholdInterval
OBJECT-TYPE
The interval over which monitored value is sampled and compared with the specified threshold.
1.3.6.1.4.1.2544.1.12.37.2.30.1.2CmPmIntervalTyperead-onlycurrent
cmL3QosPolicerThresholdVariable
OBJECT-TYPE
The object identifier of the particular variable to be sampled.
1.3.6.1.4.1.2544.1.12.37.2.30.1.3VariablePointerread-onlycurrent
cmL3QosPolicerThresholdValueLo
OBJECT-TYPE
Lower 32 bits of the threshold value.
1.3.6.1.4.1.2544.1.12.37.2.30.1.4Unsigned32read-writecurrent
cmL3QosPolicerThresholdValueHi
OBJECT-TYPE
Higher 32 bits of the threshold value.
1.3.6.1.4.1.2544.1.12.37.2.30.1.5Unsigned32read-writecurrent
cmL3QosPolicerThresholdMonValue
OBJECT-TYPE
Monitored value corresponding to cmL3QosPolicerThresholdVariable.
1.3.6.1.4.1.2544.1.12.37.2.30.1.6Counter64read-onlycurrent
cmL3QosShaperStatsTable
OBJECT-TYPE
A collection of L3 flow point Level QOS Shaper statistics. These reflect the current data.
1.3.6.1.4.1.2544.1.12.37.2.31not-accessiblecurrent
cmL3QosShaperStatsEntry
OBJECT-TYPE
A conceptual row in the cmL3QosShaperStatsTable. Entries exist in this table for each QOS Shaper per L3 flow point.
1.3.6.1.4.1.2544.1.12.37.2.31.1not-accessiblecurrent
cmL3QosShaperStatsIndex
OBJECT-TYPE
An arbitrary integer index value used to uniquely identify this QOS Shaper statistics entry. 1 - 15min 2 - 1day 3 - rollover 4 - 5min
1.3.6.1.4.1.2544.1.12.37.2.31.1.1Integer32 (1..65535)read-onlycurrent
cmL3QosShaperStatsIntervalType
OBJECT-TYPE
Interval over which Performance Monitoring data is collected.
1.3.6.1.4.1.2544.1.12.37.2.31.1.2CmPmIntervalTyperead-onlycurrent
cmL3QosShaperStatsValid
OBJECT-TYPE
Indicates the validity of the bin.
1.3.6.1.4.1.2544.1.12.37.2.31.1.3TruthValueread-onlycurrent
cmL3QosShaperStatsAction
OBJECT-TYPE
Allows the Manager to clear the bin.
1.3.6.1.4.1.2544.1.12.37.2.31.1.4CmPmBinActionread-writecurrent
cmL3QosShaperStatsBT
OBJECT-TYPE
Bytes Transmitted.
1.3.6.1.4.1.2544.1.12.37.2.31.1.5PerfCounter64read-onlycurrent
cmL3QosShaperStatsBTD
OBJECT-TYPE
Bytes Tail Dropped.
1.3.6.1.4.1.2544.1.12.37.2.31.1.6PerfCounter64read-onlycurrent
cmL3QosShaperStatsFD
OBJECT-TYPE
Frames Dequeued.
1.3.6.1.4.1.2544.1.12.37.2.31.1.7PerfCounter64read-onlycurrent
cmL3QosShaperStatsFTD
OBJECT-TYPE
Frames Tail Dropped.
1.3.6.1.4.1.2544.1.12.37.2.31.1.8PerfCounter64read-onlycurrent
cmL3QosShaperStatsBR
OBJECT-TYPE
Bytes Replicated.
1.3.6.1.4.1.2544.1.12.37.2.31.1.9PerfCounter64read-onlycurrent
cmL3QosShaperStatsFR
OBJECT-TYPE
Frames Replicated.
1.3.6.1.4.1.2544.1.12.37.2.31.1.10PerfCounter64read-onlycurrent
cmL3QosShaperStatsABRRL
OBJECT-TYPE
Average Bit Rate - Rate Limited.
1.3.6.1.4.1.2544.1.12.37.2.31.1.11PerfCounter64read-onlycurrent
cmL3QosShaperStatsABRRLR
OBJECT-TYPE
Average Bit Rate - Rate Limited, Replicated.
1.3.6.1.4.1.2544.1.12.37.2.31.1.12PerfCounter64read-onlycurrent
cmL3QosShaperStatsBREDD
OBJECT-TYPE
Bytes Random Early Discard, Dropped.
1.3.6.1.4.1.2544.1.12.37.2.31.1.13PerfCounter64read-onlycurrent
cmL3QosShaperStatsFREDD
OBJECT-TYPE
Frames Random Early Discard, Dropped.
1.3.6.1.4.1.2544.1.12.37.2.31.1.14PerfCounter64read-onlycurrent
cmL3QosShaperHistoryTable
OBJECT-TYPE
A collection of l3 flow point Level QOS Shaper statistics. These reflect the history data.
1.3.6.1.4.1.2544.1.12.37.2.32not-accessiblecurrent
cmL3QosShaperHistoryEntry
OBJECT-TYPE
A conceptual row in the cmL3QosShaperHistoryTable. Entries exist in this table for each Shaper per l3 flow point.
1.3.6.1.4.1.2544.1.12.37.2.32.1not-accessiblecurrent
cmL3QosShaperHistoryIndex
OBJECT-TYPE
An arbitrary integer index value used to uniquely identify this QOS Shaper statistics entry.
1.3.6.1.4.1.2544.1.12.37.2.32.1.1Integer32 (1..65535)read-onlycurrent
cmL3QosShaperHistoryTime
OBJECT-TYPE
Indicates the time of history bin creation.
1.3.6.1.4.1.2544.1.12.37.2.32.1.2DateAndTimeread-onlycurrent
cmL3QosShaperHistoryValid
OBJECT-TYPE
Indicates the validity of the bin.
1.3.6.1.4.1.2544.1.12.37.2.32.1.3TruthValueread-onlycurrent
cmL3QosShaperHistoryAction
OBJECT-TYPE
Allows the Manager to clear the bin.
1.3.6.1.4.1.2544.1.12.37.2.32.1.4CmPmBinActionread-writecurrent
cmL3QosShaperHistoryBT
OBJECT-TYPE
Bytes Transmitted.
1.3.6.1.4.1.2544.1.12.37.2.32.1.5PerfCounter64read-onlycurrent
cmL3QosShaperHistoryBTD
OBJECT-TYPE
Bytes Tail Dropped.
1.3.6.1.4.1.2544.1.12.37.2.32.1.6PerfCounter64read-onlycurrent
cmL3QosShaperHistoryFD
OBJECT-TYPE
Frames Dequeued.
1.3.6.1.4.1.2544.1.12.37.2.32.1.7PerfCounter64read-onlycurrent
cmL3QosShaperHistoryFTD
OBJECT-TYPE
Frames Tail Dropped.
1.3.6.1.4.1.2544.1.12.37.2.32.1.8PerfCounter64read-onlycurrent
cmL3QosShaperHistoryBR
OBJECT-TYPE
Bytes Replicated.
1.3.6.1.4.1.2544.1.12.37.2.32.1.9PerfCounter64read-onlycurrent
cmL3QosShaperHistoryFR
OBJECT-TYPE
Frames Replicated.
1.3.6.1.4.1.2544.1.12.37.2.32.1.10PerfCounter64read-onlycurrent
cmL3QosShaperHistoryABRRL
OBJECT-TYPE
Average Bit Rate - Rate Limited.
1.3.6.1.4.1.2544.1.12.37.2.32.1.11PerfCounter64read-onlycurrent
cmL3QosShaperHistoryABRRLR
OBJECT-TYPE
Average Bit Rate - Rate Limited, Replicated.
1.3.6.1.4.1.2544.1.12.37.2.32.1.12PerfCounter64read-onlycurrent
cmL3QosShaperHistoryBREDD
OBJECT-TYPE
Bytes Random Early Discard, Dropped.
1.3.6.1.4.1.2544.1.12.37.2.32.1.13PerfCounter64read-onlycurrent
cmL3QosShaperHistoryFREDD
OBJECT-TYPE
Frames Random Early Discard, Dropped.
1.3.6.1.4.1.2544.1.12.37.2.32.1.14PerfCounter64read-onlycurrent
cmL3QosShaperThresholdTable
OBJECT-TYPE
A table of entries that allow manageability of QOS Shaper Thresholds.
1.3.6.1.4.1.2544.1.12.37.2.33not-accessiblecurrent
cmL3QosShaperThresholdEntry
OBJECT-TYPE
A conceptual row in the cmL3QosShaperThresholdTable.
1.3.6.1.4.1.2544.1.12.37.2.33.1not-accessiblecurrent
cmL3QosShaperThresholdIndex
OBJECT-TYPE
An index that uniquely identifies an entry in the cmL3QosShaperThresholdTable.
1.3.6.1.4.1.2544.1.12.37.2.33.1.1Integer32 (1..65535)read-onlycurrent
cmL3QosShaperThresholdInterval
OBJECT-TYPE
The interval over which monitored value is sampled and compared with the specified threshold.
1.3.6.1.4.1.2544.1.12.37.2.33.1.2CmPmIntervalTyperead-onlycurrent
cmL3QosShaperThresholdVariable
OBJECT-TYPE
The object identifier of the particular variable to be sampled.
1.3.6.1.4.1.2544.1.12.37.2.33.1.3VariablePointerread-onlycurrent
cmL3QosShaperThresholdValueLo
OBJECT-TYPE
Lower 32 bits of the threshold value.
1.3.6.1.4.1.2544.1.12.37.2.33.1.4Unsigned32read-writecurrent
cmL3QosShaperThresholdValueHi
OBJECT-TYPE
Higher 32 bits of the threshold value.
1.3.6.1.4.1.2544.1.12.37.2.33.1.5Unsigned32read-writecurrent
cmL3QosShaperThresholdMonValue
OBJECT-TYPE
Monitored value corresponding to cmL3QosShaperThresholdVariable.
1.3.6.1.4.1.2544.1.12.37.2.33.1.6Counter64read-onlycurrent
f3L3Notifications
OBJECT-IDENTITY
1.3.6.1.4.1.2544.1.12.37.3
f3L3Conformance
OBJECT-IDENTITY
1.3.6.1.4.1.2544.1.12.37.4
f3L3Compliances
OBJECT-IDENTITY
1.3.6.1.4.1.2544.1.12.37.4.1
f3L3Groups
OBJECT-IDENTITY
1.3.6.1.4.1.2544.1.12.37.4.2
cmL3Notifications
OBJECT-IDENTITY
1.3.6.1.4.1.2544.1.12.37.5

Notifications

NameOIDStatus
f3L3FlowPointThresholdCrossingAlert
NOTIFICATION-TYPE
This trap is sent each time a threshold on a PM condition on an L3 flow point is crossed.
1.3.6.1.4.1.2544.1.12.37.3.1current
f3L3QosPolicerThresholdCrossingAlert
NOTIFICATION-TYPE
This trap is sent each time a threshold on a PM condition on an L3 Qos Policer is crossed.
1.3.6.1.4.1.2544.1.12.37.3.2current
f3L3QosShaperThresholdCrossingAlert
NOTIFICATION-TYPE
This trap is sent each time a threshold on a PM condition on an L3 Qos Shaper is crossed.
1.3.6.1.4.1.2544.1.12.37.3.3current
f3L3TrafficIpInterfaceThresholdCrossingAlert
NOTIFICATION-TYPE
This trap is sent each time a threshold on a PM condition on an L3 traffic ip interface is crossed.
1.3.6.1.4.1.2544.1.12.37.3.4current
f3L3AclRuleThresholdCrossingAlert
NOTIFICATION-TYPE
This trap is sent each time a threshold on a PM condition on an L3 acl rule is crossed.
1.3.6.1.4.1.2544.1.12.37.3.5current
f3L2A2NAclRuleThresholdCrossingAlert
NOTIFICATION-TYPE
This trap is sent each time a threshold on a PM condition on an L2 A2N acl rule is crossed.
1.3.6.1.4.1.2544.1.12.37.3.6current
f3L2N2AAclRuleThresholdCrossingAlert
NOTIFICATION-TYPE
This trap is sent each time a threshold on a PM condition on an L2 N2A acl rule is crossed.
1.3.6.1.4.1.2544.1.12.37.3.7current
f3L3TrafficIPv6InterfaceThresholdCrossingAlert
NOTIFICATION-TYPE
This trap is sent each time a threshold on a PM condition on an L3 traffic ipv6 interface is crossed.
1.3.6.1.4.1.2544.1.12.37.3.8current
cmL3FlowPointThresholdCrossingAlert
NOTIFICATION-TYPE
This trap is sent each time a threshold on a PM condition on an L3 flow point is crossed.
1.3.6.1.4.1.2544.1.12.37.5.9current
cmL3QosPolicerThresholdCrossingAlert
NOTIFICATION-TYPE
This trap is sent each time a threshold on a PM condition on an L3 Qos Policer is crossed.
1.3.6.1.4.1.2544.1.12.37.5.10current
cmL3QosShaperThresholdCrossingAlert
NOTIFICATION-TYPE
This trap is sent each time a threshold on a PM condition on an L3 Qos Shaper is crossed.
1.3.6.1.4.1.2544.1.12.37.5.11current

Conformance

NameOIDStatus
f3L3Compliance
MODULE-COMPLIANCE
Describes the requirements for conformance to the L3.
1.3.6.1.4.1.2544.1.12.37.4.1.1current
f3L3ObjectsGroup
OBJECT-GROUP
A collection of objects used to manage the L3 functionality.
1.3.6.1.4.1.2544.1.12.37.4.2.1current
f3L3PerfGroup
OBJECT-GROUP
A collection of objects performance used to manage the L3 functionality.
1.3.6.1.4.1.2544.1.12.37.4.2.2current
f3L3TrafficOspfGroup
OBJECT-GROUP
A collection of objects used to manage the L3 Ospf functionality.
1.3.6.1.4.1.2544.1.12.37.4.2.3current
f3L3TrafficIPv6Group
OBJECT-GROUP
A collection of objects used to manage the traffic ipv6 functionality.
1.3.6.1.4.1.2544.1.12.37.4.2.4current
f3L3TrafficBgpGroup
OBJECT-GROUP
A collection of objects used to manage the traffic BGP functionality.
1.3.6.1.4.1.2544.1.12.37.4.2.5current