MIBs Depot

F3-CFM-MIB

Registered at
1.3.6.1.4.1.2544.1.12.13
Last updated
2021-01-28 00:00
Organization
ADVA Optical Networking SE
Revisions
2021-01-28 00:00
Namespace
adva
Source file
F3-CFM-MIB
Digest
sha256:7e912900dbcfe1f0c6f8a6a4f8f3963254a2e5da5bb2a2058288360539518167

Description

This module defines the CFM (8021AG) Extension MIB definitions used by the F3 (FSP150CM/CC) product lines. Copyright (C) ADVA.

Contact

Web URL: http://adva.com/ E-mail: support@adva.com Postal: ADVA Optical Networking SE Campus Martinsried Fraunhoferstrasse 9a 82152 Martinsried/Munich Germany Phone: +49 089 89 06 65 0 Fax: +49 089 89 06 65 199

Imports

FromSymbols
ADVA-MIBfsp150cm
CM-COMMON-MIBAdminState, CmPmBinAction, OperationalState, PerfCounter64, SecondaryState, VlanPriority
CM-ENTITY-MIBneIndex, shelfIndex, slotIndex
CM-FACILITY-MIBcmEthernetAccPortIndex, cmEthernetNetPortIndex, cmEthernetTrafficPortIndex
IEEE8021-CFM-MIBDot1agCfmMDLevel, Dot1agCfmMepId, dot1agCfmMaCompEntry, dot1agCfmMaIndex, dot1agCfmMaNetEntry, dot1agCfmMdIndex, dot1agCfmMepEntry, dot1agCfmMepIdentifier
IF-MIBInterfaceIndex
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP
SNMPv2-SMIInteger32, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, Unsigned32, iso
SNMPv2-TCDisplayString, MacAddress, RowStatus, StorageType, TEXTUAL-CONVENTION, TruthValue, VariablePointer

Imported by

Nothing in this corpus imports this module.

Load order

Every file a consumer needs in order to load this module, dependencies first.

ADVA-MIB
BRIDGE-MIB
CM-COMMON-MIB
CM-ENTITY-MIB
CM-FACILITY-MIB
CM-REDUNDANCY-MIB
CM-SYSTEM-MIB
ENTITY-MIB
F3-CFM-MIB
F3-LAG-MIB
F3-SYNC-MIB
IANA-ADDRESS-FAMILY-NUMBERS-MIB
IANA-ENTITY-MIB
IANAifType-MIB
IEEE8021-CFM-MIB
IEEE8021-TC-MIB
IF-MIB
IPV6-TC
LLDP-MIB
LLDP-V2-MIB
LLDP-V2-TC-MIB
P-BRIDGE-MIB
Q-BRIDGE-MIB
RFC1158-MIB
RFC1271-MIB
RMON-MIB
RMON2-MIB
SNMP-FRAMEWORK-MIB
SNMP-TARGET-MIB
SNMPv2-CONF
SNMPv2-MIB
SNMPv2-SMI
SNMPv2-TC
TOKEN-RING-RMON-MIB
UUID-TC-MIB

Textual conventions

NameOIDSyntaxAccessStatus
CfmAisGenTriggerTypes
TEXTUAL-CONVENTION
Bit Mask that specifies all the defects that can trigger AIS to be generated.
current
CfmAisInterval
TEXTUAL-CONVENTION
AIS interval which is the frequency of ETH-AIS frame generation. Note the values of the 1 second and 1 minute integers which are aligned with the values defined for the AIS interval for AIS PDU in Y.1731.
current
CfmLLFTriggerTypes
TEXTUAL-CONVENTION
Bit Mask that specifies all the conditions that trigger a link loss forwarding.
current
CfmLmmDmmInterval
TEXTUAL-CONVENTION
Y.1731 Loss or delay measurement frame transmission interval.
current
CfmMepDefects
TEXTUAL-CONVENTION
A MEP can detect and report a number of defects such as RDI, MACStatus, RMEP CCM, Error CCM, Xconn CCM. These are are defined in Dot1agCfmMepDefects in standard 802.1ag MIB. Y.1731 adds additional defects such as AIS defect which is defined here. bDefAIS(0) A MEP received an ETH-AIS frame/indication.
current
CfmPduVersionType
TEXTUAL-CONVENTION
Indicates the version of the Y.1731 OAM PDUs. y1731-2008 -- Indicates the PDU formats defined in Y.1731-2008. y1731-2011 -- Indicates the PDU formats defined in Y.1731-2011.
current
CfmSignalFailTriggers
TEXTUAL-CONVENTION
Bit Mask that specifies all the conditions that trigger Signal Fail.
current
CfmSlmEnabledTypes
TEXTUAL-CONVENTION
Bit Mask that specifies all the priorities.
current

Objects

NameOIDSyntaxAccessStatus
cfmExtSvc
OBJECT-IDENTITY
1.3.6.1.4.1.2544.1.12.13.1
cfmExtSvcObjects
OBJECT-IDENTITY
1.3.6.1.4.1.2544.1.12.13.1.1
cfmExtScalars
OBJECT-IDENTITY
1.3.6.1.4.1.2544.1.12.13.1.1.1
cfmEthType
OBJECT-TYPE
This object provides the system level Ethernet type for CFM.
1.3.6.1.4.1.2544.1.12.13.1.1.1.1Integer32read-onlycurrent
cfmMacAddress
OBJECT-TYPE
This object provides the system level Mac address for CFM.
1.3.6.1.4.1.2544.1.12.13.1.1.1.2MacAddressread-onlycurrent
slmMulticastMacAddress
OBJECT-TYPE
This object can be used to configure the Synthetic Loss Measurement(SLM) Multicast MAC Address.
1.3.6.1.4.1.2544.1.12.13.1.1.1.3MacAddressread-writecurrent
slmOpcode
OBJECT-TYPE
This object can be used to configure the Operation Code for the Synthetic Loss Measurement(SLM) message.
1.3.6.1.4.1.2544.1.12.13.1.1.1.4Integer32 (0..255)read-writecurrent
slrOpcode
OBJECT-TYPE
This object can be used to configure the Operation Code for the Synthetic Loss Response(SLR) message.
1.3.6.1.4.1.2544.1.12.13.1.1.1.5Integer32 (0..255)read-writecurrent
cfmSignalFailTriggers
OBJECT-TYPE
This object can be used to configure the list of defects which constitute Signal Fail condition.
1.3.6.1.4.1.2544.1.12.13.1.1.1.6CfmSignalFailTriggersread-writecurrent
cfmMepTable
OBJECT-TYPE
Additional MEP configuration such as Y.1731 configuration.
1.3.6.1.4.1.2544.1.12.13.1.1.2not-accessiblecurrent
cfmMepEntry
OBJECT-TYPE
A list of additional MEP parameters such the Y.1731 parameters.
1.3.6.1.4.1.2544.1.12.13.1.1.2.1not-accessiblecurrent
cfmMepAdminState
OBJECT-TYPE
This object represents the Administrative State of the CFM MEPs.
1.3.6.1.4.1.2544.1.12.13.1.1.2.1.1AdminStateread-writecurrent
cfmMepAisGenTriggerTypes
OBJECT-TYPE
A bit mask which indicates all the defects that result in triggering an AIS for the higher level MEP or transmission of ETH-AIS.
1.3.6.1.4.1.2544.1.12.13.1.1.2.1.2CfmAisGenTriggerTypesread-createcurrent
cfmMepAisClientMdLevel
OBJECT-TYPE
AIS Client MD level which is the MD level used to identify any higher level local MEPs for which AIS defect needs to be set or MD level of the ETH-AIS frame generated if there are no local MEPs at this MD level.
1.3.6.1.4.1.2544.1.12.13.1.1.2.1.3Dot1agCfmMDLevelread-createcurrent
cfmMepAisInterval
OBJECT-TYPE
ETH-AIS frame transmission interval if decision is made to transmit the ETH-AIS frame.
1.3.6.1.4.1.2544.1.12.13.1.1.2.1.4CfmAisIntervalread-createcurrent
cfmMepAisGenEnabled
OBJECT-TYPE
This flag enables/disables propagation of ETH-AIS to client MD levels.
1.3.6.1.4.1.2544.1.12.13.1.1.2.1.5TruthValueread-createcurrent
cfmMepAisPriority
OBJECT-TYPE
This VLAN priority of the ETH-AIS frame.
1.3.6.1.4.1.2544.1.12.13.1.1.2.1.6VlanPriorityread-createcurrent
cfmMepLmTxCountAllPriosEnabled
OBJECT-TYPE
This attribute is used when Y.1731 probes are created and LMM frames are transmitted. As per Y.1731, loss measurement should be done per priority class. The implementation is restricted to support counting of frames for only one priority that can be modified. As an added value there is an option to count all priorities. This flag is used to decide whether to put cumulative data frame counts for all the priorities into the LMM that is transmitted by the MEP instead of data frame counts for a provisioned individual priority.
1.3.6.1.4.1.2544.1.12.13.1.1.2.1.7TruthValueread-createcurrent
cfmMepLmRxCountAllPriosEnabled
OBJECT-TYPE
This attribute is used when Y.1731 probes are created and LMR frames are transmitted. As per Y.1731, loss measurement should be done per priority class. The implementation is restricted to support counting of frames for only one priority that can be modified. As an added value there is an option to count all priorities. This flag is used to decide whether to put cumulative data frame counts for all the priorities into the LMR that is transmitted by the MEP instead of data frame counts for a provisioned individual priority. LMR is sent by a MEP when an LMM is received.
1.3.6.1.4.1.2544.1.12.13.1.1.2.1.8TruthValueread-createcurrent
cfmMepLmDualEndedCountAllPriosEnabled
OBJECT-TYPE
This attribute is used when Y.1731 probes are created and CCM frames are transmitted with loss measurement counts. As per Y.1731, loss measurement should be done per priority class. The implementation is restricted to support counting of frames for only one priority that can be modified. As an added value there is an option to count all priorities. This flag is used to decide whether to put cumulative data frame counts for all the priorities into the CCM instead of data frame counts for a provisioned individual priority.
1.3.6.1.4.1.2544.1.12.13.1.1.2.1.9TruthValueread-createcurrent
cfmMepLmCountInProfileEnabled
OBJECT-TYPE
As per the Y.1731 data frames counted for loss measurement shall be in-profile (green) data frames. As an added value, this flag is provided for the device to count all frames instead of green frames only. This flag could be set to false in cases where the remote device is not color aware and/or capable of color marking. Even if the device is capable of color marking and is color aware if the outer tag is not an S-TAG it makes sense to set this flag to false. As defined in IEEE 802.1ad the S-TAG has the drop eligibility bit that is used to mark the frames green or yellow.
1.3.6.1.4.1.2544.1.12.13.1.1.2.1.10TruthValueread-createcurrent
cfmMepLmTxPriority
OBJECT-TYPE
This attribute is used if cfmMepLmTxCountAllPrios is false. This attribute serves three purposes: - It is the VLAN priority of the LMM. - Data frames transmitted and received with this VLAN priority are counted by the MEP. The transmit count is sent in the LMM and the receive count is used to complete the list of four counts used for the loss measurement. - If an LMR is received with a VLAN priority other than this the LMR is dropped.
1.3.6.1.4.1.2544.1.12.13.1.1.2.1.11VlanPriorityread-createcurrent
cfmMepDmPriority
OBJECT-TYPE
This attribute specifies the DMM frame VLAN priority.
1.3.6.1.4.1.2544.1.12.13.1.1.2.1.12VlanPriorityread-createcurrent
cfmMepRxCCMs
OBJECT-TYPE
This provides the total number of received CCMs on the MEP.
1.3.6.1.4.1.2544.1.12.13.1.1.2.1.13PerfCounter64read-onlycurrent
cfmMepErrCCMs
OBJECT-TYPE
This provides the total number of errored CCMs on the MEP.
1.3.6.1.4.1.2544.1.12.13.1.1.2.1.14PerfCounter64read-onlycurrent
cfmMepLLFTriggerTypes
OBJECT-TYPE
This bit mask indicates the CFM triggers that result in link loss forwarding.
1.3.6.1.4.1.2544.1.12.13.1.1.2.1.15CfmLLFTriggerTypesread-createcurrent
cfmMepDefects
OBJECT-TYPE
This bit mask indicates defects that not defined in standard 802.1ag MIB such as AIS defect.
1.3.6.1.4.1.2544.1.12.13.1.1.2.1.16CfmMepDefectsread-onlycurrent
cfmMepTagEtherType
OBJECT-TYPE
This object allows management of Ether Type for MEP VLAN Tag for the MEPs.
1.3.6.1.4.1.2544.1.12.13.1.1.2.1.17Unsigned32read-writecurrent
cfmMepStatsAction
OBJECT-TYPE
Allows the Manager to clear the CFM level statistics : cfmMepRxCCMs, cfmMepErrCCMs.
1.3.6.1.4.1.2544.1.12.13.1.1.2.1.18CmPmBinActionread-writecurrent
cfmMepLbmInterval
OBJECT-TYPE
ETH-LBM frame transmission interval.
1.3.6.1.4.1.2544.1.12.13.1.1.2.1.19Integer32read-createcurrent
cfmMepOperationalState
OBJECT-TYPE
This object represents the Operational State of the CFM MEP.
1.3.6.1.4.1.2544.1.12.13.1.1.2.1.20OperationalStateread-onlycurrent
cfmMepSecondaryState
OBJECT-TYPE
This object represents the Secondary State of the CFM MEP.
1.3.6.1.4.1.2544.1.12.13.1.1.2.1.21SecondaryStateread-onlycurrent
cfmMepSlmEnabled
OBJECT-TYPE
This bit mask indicates the whether SLM is enabled per each COS.
1.3.6.1.4.1.2544.1.12.13.1.1.2.1.22CfmSlmEnabledTypesread-writecurrent
cfmMepAssociatedObject
OBJECT-TYPE
This object represents the associated port, it could be port, flow or flow point.
1.3.6.1.4.1.2544.1.12.13.1.1.2.1.23VariablePointerread-writecurrent
cfmMepPduVersion
OBJECT-TYPE
This object indicates the version of the Y.1731 OAM PDUs
1.3.6.1.4.1.2544.1.12.13.1.1.2.1.24CfmPduVersionTyperead-writecurrent
cfmMepLlbResponderEnabled
OBJECT-TYPE
This attribute specifies whether Latching Loopback Responder function is enabled.
1.3.6.1.4.1.2544.1.12.13.1.1.2.1.25TruthValueread-writecurrent
cfmMepLlbPortLLEnabled
OBJECT-TYPE
This attribute enables port loopback. In MEF 46 loopback is based on LLFS (Latching Loopback Frame Set) which is untagged or tagged. MEF 46 does not have the notion of port loopback. If this attribute is true a port loopback will be activated instead of loopback for untagged frames when LLFS is untagged.
1.3.6.1.4.1.2544.1.12.13.1.1.2.1.26TruthValueread-writecurrent
cfmMepLlbVidList
OBJECT-TYPE
This is a list of VIDs on which Latching Loopback is allowed. An empty list indicates it is allowed on any VID. This list is shall allow combination of individual VIDs and or ranges. VIDs or VID ranges are comma separated. VID ranges are of the form X1:X2 (range of VIDs from X1 to X2).
1.3.6.1.4.1.2544.1.12.13.1.1.2.1.27DisplayString (SIZE(0..512))read-writecurrent
cfmMepCcmInterfaceStatusTLVControl
OBJECT-TYPE
This attribute controls MEP option of the insertion of the Interface Status TLV in CCM messages.
1.3.6.1.4.1.2544.1.12.13.1.1.2.1.28TruthValueread-writecurrent
cfmAccPortQosShaperTable
OBJECT-TYPE
A list of configurable profile entries for CFM QoS Shapers for Access Port.
1.3.6.1.4.1.2544.1.12.13.1.1.3not-accessiblecurrent
cfmAccPortQosShaperEntry
OBJECT-TYPE
A list of parameters that set up the CFM QoS Queue profiles. This shaper is created automatically when the first Down MEP is created on a Access Port.
1.3.6.1.4.1.2544.1.12.13.1.1.3.1not-accessiblecurrent
cfmAccPortQosShaperIndex
OBJECT-TYPE
A unique index associated with the type of Access Port Based Shaper. Index 1 refers to the Shaper associated with PORT-based Down MEPs, Index 2 refers to the Shaper associated with the VID-based Down MEPs.
1.3.6.1.4.1.2544.1.12.13.1.1.3.1.1Integer32not-accessiblecurrent
cfmAccPortQosShaperCIR
OBJECT-TYPE
This object identifies the queue CIR.
1.3.6.1.4.1.2544.1.12.13.1.1.3.1.2Unsigned32read-writecurrent
cfmAccPortQosShaperBufSize
OBJECT-TYPE
This object identifies the queue buffer size.
1.3.6.1.4.1.2544.1.12.13.1.1.3.1.3Unsigned32read-writecurrent
cfmAccPortQosShaperAdminState
OBJECT-TYPE
This object allows the management of the Shaper Administrative State. Only 'in-service' and 'management' states are allowed.
1.3.6.1.4.1.2544.1.12.13.1.1.3.1.4AdminStateread-writecurrent
cfmNetPortQosShaperTable
OBJECT-TYPE
A list of configurable profile entries for CFM QoS Shapers for Network Port.
1.3.6.1.4.1.2544.1.12.13.1.1.4not-accessiblecurrent
cfmNetPortQosShaperEntry
OBJECT-TYPE
A list of parameters that set up the CFM QoS Queue profiles. This shaper is created automatically when the first Down MEP is created on a Network Port.
1.3.6.1.4.1.2544.1.12.13.1.1.4.1not-accessiblecurrent
cfmNetPortQosShaperTypeIndex
OBJECT-TYPE
A unique index associated with the type of Network Port Based Shaper. Index 1 refers to the Shaper associated with PORT-based Down MEPs, Index 2 refers to the Shaper associated with the VID-based Down MEPs.
1.3.6.1.4.1.2544.1.12.13.1.1.4.1.1Integer32not-accessiblecurrent
cfmNetPortQosShaperCIR
OBJECT-TYPE
This object identifies the queue CIR.
1.3.6.1.4.1.2544.1.12.13.1.1.4.1.2Unsigned32read-writecurrent
cfmNetPortQosShaperBufSize
OBJECT-TYPE
This object identifies the queue buffer size.
1.3.6.1.4.1.2544.1.12.13.1.1.4.1.3Unsigned32read-writecurrent
cfmNetPortQosShaperAdminState
OBJECT-TYPE
This object allows the management of the Shaper Administrative State. Only 'in-service' and 'management' states are allowed.
1.3.6.1.4.1.2544.1.12.13.1.1.4.1.4AdminStateread-writecurrent
cfmServerMepTable
OBJECT-TYPE
Server MEP management table.
1.3.6.1.4.1.2544.1.12.13.1.1.5not-accessiblecurrent
cfmServerMepEntry
OBJECT-TYPE
This allows management of Server MEPs.
1.3.6.1.4.1.2544.1.12.13.1.1.5.1not-accessiblecurrent
cfmServerMepIndex
OBJECT-TYPE
The integer index value corresponding to a Server MEP.
1.3.6.1.4.1.2544.1.12.13.1.1.5.1.1Integer32read-createcurrent
cfmServerMepAssociatedPort
OBJECT-TYPE
This is the port on which the CFM Server MEP is created.
1.3.6.1.4.1.2544.1.12.13.1.1.5.1.2VariablePointerread-createcurrent
cfmServerMepAisClientMdLevel
OBJECT-TYPE
AIS Client MD level which is the MD level used to identify any higher level local MEPs for which AIS defect needs to be set or MD level of the ETH-AIS frame generated if there are no local MEPs at this MD level.
1.3.6.1.4.1.2544.1.12.13.1.1.5.1.3Dot1agCfmMDLevelread-createcurrent
cfmServerMepAisInterval
OBJECT-TYPE
ETH-AIS frame transmission interval if decision is made to transmit the ETH-AIS frame.
1.3.6.1.4.1.2544.1.12.13.1.1.5.1.4CfmAisIntervalread-createcurrent
cfmServerMepAisGenEnabled
OBJECT-TYPE
This flag enables/disables propagation of ETH-AIS to client MD levels.
1.3.6.1.4.1.2544.1.12.13.1.1.5.1.5TruthValueread-createcurrent
cfmServerMepAisPriority
OBJECT-TYPE
This VLAN priority of the ETH-AIS frame.
1.3.6.1.4.1.2544.1.12.13.1.1.5.1.6VlanPriorityread-createcurrent
cfmServerMepStorageType
OBJECT-TYPE
The type of storage configured for this entry.
1.3.6.1.4.1.2544.1.12.13.1.1.5.1.7StorageTyperead-createcurrent
cfmServerMepRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of cfmServerMepRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with cfmServerMepRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The cfmServerMepRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.13.1.1.5.1.8RowStatusread-createcurrent
cfmServerMepAdminState
OBJECT-TYPE
This object represents the Administrative State of the Server MEP.
1.3.6.1.4.1.2544.1.12.13.1.1.5.1.9AdminStateread-writecurrent
cfmServerMepOperationalState
OBJECT-TYPE
This object represents the Operational State of the Server MEP.
1.3.6.1.4.1.2544.1.12.13.1.1.5.1.10OperationalStateread-onlycurrent
cfmServerMepSecondaryState
OBJECT-TYPE
This object represents the Secondary State of the CFM MEP.
1.3.6.1.4.1.2544.1.12.13.1.1.5.1.11SecondaryStateread-onlycurrent
cfmDownMEPQosShaperTable
OBJECT-TYPE
A list of configurable profile entries for CFM QoS Shapers for down MEPs.
1.3.6.1.4.1.2544.1.12.13.1.1.6not-accessiblecurrent
cfmDownMEPQosShaperEntry
OBJECT-TYPE
A list of parameters that set up the CFM QoS Queue profiles. This shaper is created automatically when the first Down MEP is created on a Port. Note, this queues is valid for port based Down MEPs, VID based down MEPs on NNI port.
1.3.6.1.4.1.2544.1.12.13.1.1.6.1not-accessiblecurrent
cfmDownMEPQosShaperIndex
OBJECT-TYPE
A unique index associated with the Shaper for Down MEPs.
1.3.6.1.4.1.2544.1.12.13.1.1.6.1.1Integer32not-accessiblecurrent
cfmDownMEPQosShaperType
OBJECT-TYPE
Type of Shaper for Down MEPs. 1 refers to the Shaper associated with Down MEPs(for both port based and VID based) fot Transimit direction, 2 refers to the Shaper associated with Down MEPs(for both port based and VID based) fot Receiving direction
1.3.6.1.4.1.2544.1.12.13.1.1.6.1.2Integer32read-onlycurrent
cfmDownMEPQosShaperCIR
OBJECT-TYPE
This object identifies the queue CIR.
1.3.6.1.4.1.2544.1.12.13.1.1.6.1.3Unsigned32read-writecurrent
cfmDownMEPQosShaperProfile
OBJECT-TYPE
This object identifies the OID of cmQosQueueProfileIndex in the cmQosQueueProfileTable.
1.3.6.1.4.1.2544.1.12.13.1.1.6.1.4VariablePointerread-writecurrent
cfmDownMEPQosShaperAdminState
OBJECT-TYPE
This object allows the management of the Shaper Administrative State. Only 'in-service' and 'management' states are allowed.
1.3.6.1.4.1.2544.1.12.13.1.1.6.1.5AdminStateread-writecurrent
cfmMepExcludedMepListTable
OBJECT-TYPE
A list of configurable profile entries for CFM excluded mep list.
1.3.6.1.4.1.2544.1.12.13.1.1.7not-accessiblecurrent
cfmMepExcludedMepListEntry
OBJECT-TYPE
Excluded Remote Mep List for local Mep, not expected to receive OAM from these MEPs.
1.3.6.1.4.1.2544.1.12.13.1.1.7.1not-accessiblecurrent
cfmMepExcludedMepListIdentifier
OBJECT-TYPE
A unique index associated with CfmMepExcludedMepListEntry.
1.3.6.1.4.1.2544.1.12.13.1.1.7.1.1Unsigned32 (1..8191)not-accessiblecurrent
cfmMepExcludedMepListRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of cfmMepExcludedMepListRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with cfmMepExcludedMepListRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The cfmMepExcludedMepListRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.13.1.1.7.1.2RowStatusread-createcurrent
cfmMepLbrTable
OBJECT-TYPE
A list of configurable profile entries for MepLbr.
1.3.6.1.4.1.2544.1.12.13.1.1.8not-accessiblecurrent
cfmMepLbrEntry
OBJECT-TYPE
MEP LBR statistic table.
1.3.6.1.4.1.2544.1.12.13.1.1.8.1not-accessiblecurrent
cfmMepLbrMacAddress
OBJECT-TYPE
Source Mac Address of LBR.
1.3.6.1.4.1.2544.1.12.13.1.1.8.1.1MacAddressread-onlycurrent
cfmMepLbrMepId
OBJECT-TYPE
Remote MEP ID.
1.3.6.1.4.1.2544.1.12.13.1.1.8.1.2Integer32read-onlycurrent
cfmMepLbrInOrder
OBJECT-TYPE
Total valid in-order LBR received.
1.3.6.1.4.1.2544.1.12.13.1.1.8.1.3PerfCounter64read-onlycurrent
cfmMepLbrOutOfOder
OBJECT-TYPE
Total valid out of order LBR received.
1.3.6.1.4.1.2544.1.12.13.1.1.8.1.4PerfCounter64read-onlycurrent
cfmMaCompTable
OBJECT-TYPE
A additional list of MA components.
1.3.6.1.4.1.2544.1.12.13.1.1.9not-accessiblecurrent
cfmMaCompEntry
OBJECT-TYPE
A list of additional maCompEntry.
1.3.6.1.4.1.2544.1.12.13.1.1.9.1not-accessiblecurrent
cfmMaCompIndex
OBJECT-TYPE
This object represents the maComp number value.
1.3.6.1.4.1.2544.1.12.13.1.1.9.1.1Unsigned32read-onlycurrent
cfmMaCompEntity
OBJECT-TYPE
This object represents the maComp entity, it is should be port or flow's oid.
1.3.6.1.4.1.2544.1.12.13.1.1.9.1.2VariablePointerread-createcurrent
cfmMaNetTable
OBJECT-TYPE
A additional list of MA.
1.3.6.1.4.1.2544.1.12.13.1.1.10not-accessiblecurrent
cfmMaNetEntry
OBJECT-TYPE
A list of additional maNetEntry.
1.3.6.1.4.1.2544.1.12.13.1.1.10.1not-accessiblecurrent
cfmMaNetRemoteMepAutoDiscovery
OBJECT-TYPE
This object represents whether learn remote mep automatically.
1.3.6.1.4.1.2544.1.12.13.1.1.10.1.1TruthValueread-writecurrent
cfmMaNetMepNumbers
OBJECT-TYPE
This object represents the max number of meps per MA.
1.3.6.1.4.1.2544.1.12.13.1.1.10.1.2Unsigned32read-writecurrent
cfmTrafficPortQosShaperTable
OBJECT-TYPE
A list of configurable entries for CFM QoS Shapers for Traffic Ports.
1.3.6.1.4.1.2544.1.12.13.1.1.11not-accessiblecurrent
cfmTrafficPortQosShaperEntry
OBJECT-TYPE
A list of parameters that set up the CFM QoS Queue profiles. This shaper is created automatically when the first Down MEP is created on a Traffic Port.
1.3.6.1.4.1.2544.1.12.13.1.1.11.1not-accessiblecurrent
cfmTrafficPortQosShaperIndex
OBJECT-TYPE
A unique index associated with the type of Traffic Port Based Shaper. Index 1 refers to the Shaper associated with PORT-based Down MEPs, Index 2 refers to the Shaper associated with the VID-based Down MEPs.
1.3.6.1.4.1.2544.1.12.13.1.1.11.1.1Integer32not-accessiblecurrent
cfmTrafficPortQosShaperCIR
OBJECT-TYPE
This object identifies the queue CIR.
1.3.6.1.4.1.2544.1.12.13.1.1.11.1.2Unsigned32read-writecurrent
cfmTrafficPortQosShaperBufSize
OBJECT-TYPE
This object identifies the queue buffer size.
1.3.6.1.4.1.2544.1.12.13.1.1.11.1.3Unsigned32read-writecurrent
cfmTrafficPortQosShaperAdminState
OBJECT-TYPE
This object allows the management of the Shaper Administrative State. Only 'in-service' and 'management' states are allowed.
1.3.6.1.4.1.2544.1.12.13.1.1.11.1.4AdminStateread-writecurrent
cfmMepLlbMacAddressTable
OBJECT-TYPE
A additional list of MAC Addresses.
1.3.6.1.4.1.2544.1.12.13.1.1.12not-accessiblecurrent
cfmLlbMacAddressEntry
OBJECT-TYPE
A conceptual row in the cfmMepLlbMacAddressTable.
1.3.6.1.4.1.2544.1.12.13.1.1.12.1not-accessiblecurrent
cfmLlbMacAddress
OBJECT-TYPE
This object represents the Latching Loopback MAC Addresses.
1.3.6.1.4.1.2544.1.12.13.1.1.12.1.1MacAddressnot-accessiblecurrent
cfmLlbMacAddressRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of cfmLlbMacAddressRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with cfmLlbMacAddressRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The cfmLlbMacAddressRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.13.1.1.12.1.2RowStatusread-createcurrent
cfmExtSvcConformance
OBJECT-IDENTITY
1.3.6.1.4.1.2544.1.12.13.1.2
cfmExtSvcCompliances
OBJECT-IDENTITY
1.3.6.1.4.1.2544.1.12.13.1.2.1
cfmExtSvcGroups
OBJECT-IDENTITY
1.3.6.1.4.1.2544.1.12.13.1.2.2

Conformance

NameOIDStatus
cfmExtCompliance
MODULE-COMPLIANCE
Describes the requirements for conformance to the CFM Extensions.
1.3.6.1.4.1.2544.1.12.13.1.2.1.1current
cfmExtGroup
OBJECT-GROUP
******************THIS OBJECT GROUP IS NOW DEPRECATED ****************** A collection of objects used to identify CFM extension implementation compliance.
1.3.6.1.4.1.2544.1.12.13.1.2.2.1deprecated
cfmGenGroup
OBJECT-GROUP
A collection of objects used to identify CFM extension implementation compliance.
1.3.6.1.4.1.2544.1.12.13.1.2.2.2current
cfmMepGroup
OBJECT-GROUP
A collection of objects used to identify additional CFM MEP functions.
1.3.6.1.4.1.2544.1.12.13.1.2.2.3current
cfmPortShaperGroup
OBJECT-GROUP
A collection of objects used to identify CFM Port Shaper functionality.
1.3.6.1.4.1.2544.1.12.13.1.2.2.4current
cfmServerMepGroup
OBJECT-GROUP
A collection of objects used to identify CFM Server MEP functionality.
1.3.6.1.4.1.2544.1.12.13.1.2.2.5current
cfmMaCompGroup
OBJECT-GROUP
A collection of additional objects used to show maComp.
1.3.6.1.4.1.2544.1.12.13.1.2.2.6current