MIBs Depot

CM-SA-MIB

Registered at
1.3.6.1.4.1.2544.1.12.8
Last updated
2019-12-01 00:00
Organization
ADVA Optical Networking SE
Revisions
2019-12-01 00:00
Namespace
adva
Source file
CM-SA-MIB
Digest
sha256:db71cf0600b66bde2edae30957afb1f8a5428a162e77277b72ddd341f7dd7bc0

Description

This module defines the Service Assurance MIB definitions used by the F3 (FSP150CM/CC) product lines. Copyright (C) ADVA.

Contact

Web URL: http://adva.com/ E-mail: support@adva.com Postal: ADVA Optical Networking SE Campus Martinsried Fraunhoferstrasse 9a 82152 Martinsried/Munich Germany Phone: +49 089 89 06 65 0 Fax: +49 089 89 06 65 199

Imports

FromSymbols
ADVA-MIBfsp150cm
CM-COMMON-MIBAdminState, ClassOfServiceType, CmPmBinAction, IpPriorityMapMode, IpVersion, MepDestinationType, OperationalState, PerfCounter32, PerfCounter64, SchedActivityStatus, ScheduleType, SecondaryState, TrafficDirection, VlanId, VlanPriority
CM-ENTITY-MIBneIndex, shelfIndex, slotIndex
CM-FACILITY-MIBBitErrRate, PolicerColorMode
IEEE8021-CFM-MIBDot1agCfmMepIdOrZero
IPV6-TCIpv6Address
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP
SNMPv2-SMICounter64, Integer32, IpAddress, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, Unsigned32, iso
SNMPv2-TCDateAndTime, DisplayString, MacAddress, RowStatus, StorageType, TEXTUAL-CONVENTION, TruthValue, VariablePointer

Imported by

1 module(s) in this corpus import this one.

Load order

Every file a consumer needs in order to load this module, dependencies first.

ADVA-MIB
BRIDGE-MIB
CM-COMMON-MIB
CM-ENTITY-MIB
CM-FACILITY-MIB
CM-REDUNDANCY-MIB
CM-SA-MIB
CM-SYSTEM-MIB
ENTITY-MIB
F3-LAG-MIB
F3-SYNC-MIB
IANA-ADDRESS-FAMILY-NUMBERS-MIB
IANA-ENTITY-MIB
IANAifType-MIB
IEEE8021-CFM-MIB
IEEE8021-TC-MIB
IF-MIB
IPV6-TC
LLDP-MIB
LLDP-V2-MIB
LLDP-V2-TC-MIB
P-BRIDGE-MIB
Q-BRIDGE-MIB
RFC1158-MIB
RFC1271-MIB
RMON-MIB
RMON2-MIB
SNMP-FRAMEWORK-MIB
SNMP-TARGET-MIB
SNMPv2-CONF
SNMPv2-MIB
SNMPv2-SMI
SNMPv2-TC
TOKEN-RING-RMON-MIB
UUID-TC-MIB

Textual conventions

NameOIDSyntaxAccessStatus
BerTestMode
TEXTUAL-CONVENTION
BER Test Control Test Mode.
current
BerTestStatus
TEXTUAL-CONVENTION
BER Test Status.
current
BertControlAction
TEXTUAL-CONVENTION
BER Test Control Action.
current
BertPattern
TEXTUAL-CONVENTION
BERT Tx Pattern.
current
BertSyncState
TEXTUAL-CONVENTION
BERT Sync State.
current
BertUserPatternLength
TEXTUAL-CONVENTION
BERT Error Rate.
current
EcpaControlAction
TEXTUAL-CONVENTION
ECPA Control Action.
current
EcpaMonitorPortType
TEXTUAL-CONVENTION
ECPA Monitor Port Type.
current
EcpaPayloadType
TEXTUAL-CONVENTION
ECPA Payload Type.
current
EcpaTestStatus
TEXTUAL-CONVENTION
ECPA Test Status.
current
EcpaTestType
TEXTUAL-CONVENTION
ECPA Control Test Type.
current
EcpaType
TEXTUAL-CONVENTION
ECPA Type.
current
EsaAction
TEXTUAL-CONVENTION
ESA Scheduled Group/Reflector Action.
current
EsaProbeDirection
TEXTUAL-CONVENTION
ESA Probe Direction.
current
EsaProbeDistStatsType
TEXTUAL-CONVENTION
Indicates the ESA Probe Statistics Distribution Type.
current
EsaProbeHistoryIntervalType
TEXTUAL-CONVENTION
ESA Probe Y1731 History Interval Types.
current
EsaProbePktIntervalType
TEXTUAL-CONVENTION
Interval Type used for LMM and DMM messages.
current
EsaProbePmIntervalType
TEXTUAL-CONVENTION
ESA Probe PM Interval Types.
current
EsaProbeProtocol
TEXTUAL-CONVENTION
ESA Probe Protocol Types.
current
EsaProbeSLAMonitorType
TEXTUAL-CONVENTION
ESA Probe SLA Monitor Type.
current
EsaReflectorDirection
TEXTUAL-CONVENTION
ESA Reflector Direction.
current

Objects

NameOIDSyntaxAccessStatus
cmServAssuranceObjects
OBJECT-IDENTITY
1.3.6.1.4.1.2544.1.12.8.1
ecpaControlTable
OBJECT-TYPE
A list of entries for the control of Etherjack Connection Performance Analyzer Streams. Upto 12 ECPA streams can be configured per test head; 3 ECPA streams can be simultaneously executed.
1.3.6.1.4.1.2544.1.12.8.1.1not-accessiblecurrent
ecpaControlEntry
OBJECT-TYPE
A conceptual row in the ecpaControlTable.
1.3.6.1.4.1.2544.1.12.8.1.1.1not-accessiblecurrent
ecpaControlIndex
OBJECT-TYPE
An arbitrary integer index value used to uniquely identify this Etherjack Connection Performance Analyzer Control Test head. There is only one test head per card.
1.3.6.1.4.1.2544.1.12.8.1.1.1.1Integer32read-onlycurrent
ecpaControlSourcePort
OBJECT-TYPE
Pointer to the Access or Network Port on which the ECPA test will be started within a card.
1.3.6.1.4.1.2544.1.12.8.1.1.1.2VariablePointerread-writecurrent
ecpaControlTestType
OBJECT-TYPE
The type of ECPA test to be performed. When 'duration' test is specified, ECPA test is run for 'ecpaControlDuration' time. When 'numFrames' test is specified, ECPA test is run for 'ecpaControlNumFrames', when 'continous' test is specified, ECPA test is run until an explicit 'ecpaControlAction' of 'stop' of received.
1.3.6.1.4.1.2544.1.12.8.1.1.1.3EcpaTestTyperead-writecurrent
ecpaControlNumFrames
OBJECT-TYPE
This object enables specification of the number of frames for traffic generation. Traffic Generation will be completed after the specified number of frames are transmitted.
1.3.6.1.4.1.2544.1.12.8.1.1.1.4Integer32 (0..2147483647)read-writecurrent
ecpaControlDuration
OBJECT-TYPE
This object enables specification of the time in seconds for traffic generation. Traffic Generation will be stopped after the specified time interval is exhausted.
1.3.6.1.4.1.2544.1.12.8.1.1.1.5Integer32 (0..259200)read-writecurrent
ecpaControlInjectorDirection
OBJECT-TYPE
This object enables specification of the direction of traffic generation. This value must be specified if the interface is used for traffic generation. Both of ecpaControlInjectorDirection and ecpaControlMonitorDirection must be specified.
1.3.6.1.4.1.2544.1.12.8.1.1.1.6TrafficDirectionread-writecurrent
ecpaControlMonitorDirection
OBJECT-TYPE
This object enables specification of the direction of receival of generated traffic. This value must be specified if the interface is used for receiving/monitoring generated traffic. Both of ecpaControlInjectorDirection and ecpaControlMonitorDirection must be specified.
1.3.6.1.4.1.2544.1.12.8.1.1.1.7TrafficDirectionread-writecurrent
ecpaControlStream1
OBJECT-TYPE
This object specifies which stream should be included in the ECPA execution. Value of 0 indicates that no streams is selected by ecpaControlStream1. Non 0 value indicates the selected ECPA stream.
1.3.6.1.4.1.2544.1.12.8.1.1.1.8Integer32 (0..48)read-writecurrent
ecpaControlStream2
OBJECT-TYPE
This object specifies which stream should be included in the ECPA execution. Value of 0 indicates that no streams is selected by ecpaControlStream2. Non 0 value indicates the selected ECPA stream.
1.3.6.1.4.1.2544.1.12.8.1.1.1.9Integer32 (0..48)read-writecurrent
ecpaControlStream3
OBJECT-TYPE
This object specifies which stream should be included in the ECPA execution. Value of 0 indicates that no streams is selected by ecpaControlStream3. Non 0 value indicates the selected ECPA stream.
1.3.6.1.4.1.2544.1.12.8.1.1.1.10Integer32 (0..48)read-writecurrent
ecpaControlAction
OBJECT-TYPE
This object enables starting/stopping of traffic generation as well as resetting of monitored streams. This object may not be specified at configuration creation time - in this case it will take the value of `none'. This allows manager to explicitly control the start and stop of traffic generation/monitoring activity. Value of `stop' is invalid if the activity is specified but not started. Value of `start' is valid during creation time, as well as when activity is already stopped. Specification of `reset' resets the specified streams to default values, as well as clears the control specification. Get on this variable gives the most recent SNMP set specification.
1.3.6.1.4.1.2544.1.12.8.1.1.1.11EcpaControlActionread-writecurrent
ecpaControlTestStatus
OBJECT-TYPE
This object reflects the current status of test set configuration entry. Upon creation, the status has a value of `initial'; the status changes to `in-progress' upon ecpaControlAction indicating `start'; the status changes to `completed' upon ecpaControlAction indicating stop, as well as when the specified test generation completes autonomously upon completion of number of frames or completion of specified time interval.
1.3.6.1.4.1.2544.1.12.8.1.1.1.12EcpaTestStatusread-onlycurrent
ecpaControlStorageType
OBJECT-TYPE
The type of storage configured for this entry.
1.3.6.1.4.1.2544.1.12.8.1.1.1.13StorageTyperead-createcurrent
ecpaControlRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of ecpaControlRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with ecpaControlRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The ecpaControlRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.8.1.1.1.14RowStatusread-createcurrent
ecpaControlEcpaType
OBJECT-TYPE
ECPA test can run in a regular mode(1) or enhaced mode (2).
1.3.6.1.4.1.2544.1.12.8.1.1.1.15EcpaTyperead-writecurrent
ecpaControlMonitorPortType
OBJECT-TYPE
ECPA monitor port type.
1.3.6.1.4.1.2544.1.12.8.1.1.1.16EcpaMonitorPortTyperead-createcurrent
ecpaConfigStreamTable
OBJECT-TYPE
A list of entries for the configuration of Etherjack Connection Performance Analyzer Stream Specifications.
1.3.6.1.4.1.2544.1.12.8.1.2not-accessiblecurrent
ecpaConfigStreamEntry
OBJECT-TYPE
A conceptual row in the ecpaConfigStreamTable.
1.3.6.1.4.1.2544.1.12.8.1.2.1not-accessiblecurrent
ecpaConfigStreamIndex
OBJECT-TYPE
An arbitrary integer index value used to uniquely identify this Etherjack Connection Performance Analyzer.
1.3.6.1.4.1.2544.1.12.8.1.2.1.1Integer32 (1..48)read-writecurrent
ecpaConfigStreamName
OBJECT-TYPE
Symbolic Stream Name that can be associated with an ECPA stream.
1.3.6.1.4.1.2544.1.12.8.1.2.1.2DisplayString (SIZE(0..64))read-writecurrent
ecpaConfigStreamFrameSize
OBJECT-TYPE
This object enables specification of fixed length frame size in bytes for traffic generation. If not specified, default value of 64 bytes is used. CM Aggregation Product limits the upper range value to 9600.
1.3.6.1.4.1.2544.1.12.8.1.2.1.3Integer32 (64..9612)read-writecurrent
ecpaConfigStreamRate
OBJECT-TYPE
The object enables specification of the traffic generation rate.
1.3.6.1.4.1.2544.1.12.8.1.2.1.4Unsigned32read-writecurrent
ecpaConfigStreamPayloadType
OBJECT-TYPE
This object enables specification of type of payload to generate `fixed' type indicates a generation pattern of 5A, A5, 5A, A5 bytes. `random' type indicates traffic generation with pseudo-random pattern.
1.3.6.1.4.1.2544.1.12.8.1.2.1.5EcpaPayloadTyperead-writecurrent
ecpaConfigStreamSignature
OBJECT-TYPE
Indicates an 8-byte signature specified by the user in hexadecimal or ASCII format. This signature is currently used by the FSP150Mx products for test frame recognition and will be appended directly after the ECPA Signature in the test frame and be 4-byte aligned. This will allow the F3 ECPA feature to interoperate with the existing FSP150Mx products. Hexadecimal signature must be prefixed with 0x/0X.
1.3.6.1.4.1.2544.1.12.8.1.2.1.6DisplayString (SIZE(0..10))read-writecurrent
ecpaConfigStreamDestinationMAC
OBJECT-TYPE
Allows specification of destination MAC in the generated traffic.
1.3.6.1.4.1.2544.1.12.8.1.2.1.7MacAddressread-writecurrent
ecpaConfigStreamSourceMAC
OBJECT-TYPE
Allows specification of source MAC in the generated traffic.
1.3.6.1.4.1.2544.1.12.8.1.2.1.8MacAddressread-writecurrent
ecpaConfigStreamOuterVlanEnabled
OBJECT-TYPE
Allows specification of a VLAN tagged ECPA stream. This variable enables the outer VLAN specification, in the case of a doubly tagged ECPA stream. If a singly tagged ECPA stream is desired, this specification is mandatory.
1.3.6.1.4.1.2544.1.12.8.1.2.1.9TruthValueread-writecurrent
ecpaConfigStreamOuterVlanId
OBJECT-TYPE
Outer VLAN Id associated with the ECPA stream. Valid only if ecpaConfigStreamOuterVlanEnabled is enabled.
1.3.6.1.4.1.2544.1.12.8.1.2.1.10VlanIdread-writecurrent
ecpaConfigStreamOuterVlanPrio
OBJECT-TYPE
Outer VLAN Priority associated with the ECPA stream. Valid only if ecpaConfigStreamOuterVlanEnabled is enabled.
1.3.6.1.4.1.2544.1.12.8.1.2.1.11VlanPriorityread-writecurrent
ecpaConfigStreamOuterVlanEtherType
OBJECT-TYPE
EtherType associated with the Outer VLAN Tag. Valid only if ecpaConfigStreamOuterVlanEnabled is enabled.
1.3.6.1.4.1.2544.1.12.8.1.2.1.12Integer32 (0..65535)read-writecurrent
ecpaConfigStreamInnerVlanEnabled
OBJECT-TYPE
Allows specification of a VLAN tagged ECPA stream. This variable enables the outer VLAN specification, in the case of a doubly tagged ECPA stream. If a singly tagged ECPA stream is desired, this specification is mandatory.
1.3.6.1.4.1.2544.1.12.8.1.2.1.13TruthValueread-writecurrent
ecpaConfigStreamInnerVlanId
OBJECT-TYPE
Inner VLAN Id associated with the ECPA stream. Valid only if ecpaConfigStreamInnerVlanEnabled is enabled.
1.3.6.1.4.1.2544.1.12.8.1.2.1.14VlanIdread-writecurrent
ecpaConfigStreamInnerVlanPrio
OBJECT-TYPE
Inner VLAN Priority associated with the ECPA stream. Valid only if ecpaConfigStreamInnerVlanEnabled is enabled.
1.3.6.1.4.1.2544.1.12.8.1.2.1.15VlanPriorityread-writecurrent
ecpaConfigStreamInnerVlanEtherType
OBJECT-TYPE
EtherType associated with the Inner VLAN Tag. Valid only if ecpaConfigStreamInnerVlanEnabled is enabled.
1.3.6.1.4.1.2544.1.12.8.1.2.1.16Integer32 (0..65535)read-writecurrent
ecpaConfigStreamIpVersion
OBJECT-TYPE
This object enables specification of IP data in the generated test traffic. Value of `ipv4' allows test data to be IP v4 compatible. Value of `ipv6' allows test data to be IP v6 compatible.
1.3.6.1.4.1.2544.1.12.8.1.2.1.17IpVersionread-writecurrent
ecpaConfigStreamIpV4Address
OBJECT-TYPE
This object enables specification of ipv4 IP Address for the test stream.This is used when ecpaConfigStreamIpVersion is ipv4.
1.3.6.1.4.1.2544.1.12.8.1.2.1.18IpAddressread-writecurrent
ecpaConfigStreamIpV6Address
OBJECT-TYPE
This object enables specification of ipv6 IP Address for the test stream.This is used when ecpaConfigStreamIpVersion is ipv6.
1.3.6.1.4.1.2544.1.12.8.1.2.1.19Ipv6Addressread-writecurrent
ecpaConfigStreamPrioMapMode
OBJECT-TYPE
This object enables specification of Priority Mapping Mode for the test stream.
1.3.6.1.4.1.2544.1.12.8.1.2.1.20IpPriorityMapModeread-writecurrent
ecpaConfigStreamPrioVal
OBJECT-TYPE
This object enables specification of Priority Value for ecpaConfigStreamPrioMapMode as TOS/DSCP.
1.3.6.1.4.1.2544.1.12.8.1.2.1.21Integer32 (0..63)read-writecurrent
ecpaConfigStreamInnerVlan2Enabled
OBJECT-TYPE
Allows specification of a VLAN tagged ECPA stream. This variable enables the second(inner) VLAN specification, in the case of a 3-tagged ECPA stream. If a three tagged ECPA stream is desired, this specification is mandatory.
1.3.6.1.4.1.2544.1.12.8.1.2.1.22TruthValueread-writecurrent
ecpaConfigStreamInnerVlan2Id
OBJECT-TYPE
Inner (second) VLAN Id associated with the ECPA stream. Valid only if ecpaConfigStreamInnerVlan2Enabled is enabled.
1.3.6.1.4.1.2544.1.12.8.1.2.1.23VlanIdread-writecurrent
ecpaConfigStreamInnerVlan2Prio
OBJECT-TYPE
Inner (second) VLAN Priority associated with the ECPA stream. Valid only if ecpaConfigStreamInnerVlan2Enabled is enabled.
1.3.6.1.4.1.2544.1.12.8.1.2.1.24VlanPriorityread-writecurrent
ecpaConfigStreamInnerVlan2EtherType
OBJECT-TYPE
EtherType associated with the Inner (second) VLAN Tag. Valid only if ecpaConfigStreamInnerVlan2Enabled is enabled.
1.3.6.1.4.1.2544.1.12.8.1.2.1.25Integer32 (0..65535)read-writecurrent
ecpaConfigStreamDestIpV4Address
OBJECT-TYPE
This object enables specification of destination ipv4 IP Address for the test stream.This is used when ecpaConfigStreamIpVersion is ipv4.
1.3.6.1.4.1.2544.1.12.8.1.2.1.26IpAddressread-writecurrent
ecpaConfigStreamDestIpV6Address
OBJECT-TYPE
This object enables specification of destination ipv6 IP Address for the test stream.This is used when ecpaConfigStreamIpVersion is ipv6.
1.3.6.1.4.1.2544.1.12.8.1.2.1.27Ipv6Addressread-writecurrent
ecpaConfigStreamUsePortSourceMAC
OBJECT-TYPE
This object when not enabled indicates that MAC Address specified by ecpaConfigStreamSourceMAC as the source MAC Address of the ECPA test stream. For EGX, if enabled indicates that the corresponding ECPA test stream will use the associated Source Port's MAC Address. For GE110 products and CC products, if enabled indicates that the corresponding ECPA test stream will use the associated Source Port's Diagnostic MAC Address.
1.3.6.1.4.1.2544.1.12.8.1.2.1.28TruthValueread-writecurrent
ecpaConfigStreamRateHi
OBJECT-TYPE
The object enables specification of the higher 32 bits of the traffic generation rate.
1.3.6.1.4.1.2544.1.12.8.1.2.1.29Unsigned32read-writecurrent
ecpaConfigStreamUdpControl
OBJECT-TYPE
This object enables or disables UDP header.
1.3.6.1.4.1.2544.1.12.8.1.2.1.30TruthValueread-writecurrent
ecpaConfigStreamUdpSrcPort
OBJECT-TYPE
When UDP control is enabled, this object provides the UDP source port. Otherwize it is ignored.
1.3.6.1.4.1.2544.1.12.8.1.2.1.31Integer32 (1..65535)read-writecurrent
ecpaConfigStreamUdpDstPort
OBJECT-TYPE
When UDP control is enabled, this object provides the UDP destination port. Otherwize it is ignored.
1.3.6.1.4.1.2544.1.12.8.1.2.1.32Integer32 (1..65535)read-writecurrent
ecpaTestStreamTable
OBJECT-TYPE
A list of entries containing results of a previous test.
1.3.6.1.4.1.2544.1.12.8.1.3not-accessiblecurrent
ecpaTestStreamEntry
OBJECT-TYPE
A conceptual row in the ecpaTestStreamTable. Entries in this table show results of the current ECPA test.
1.3.6.1.4.1.2544.1.12.8.1.3.1not-accessiblecurrent
ecpaTestStreamIndex
OBJECT-TYPE
An integer index value corresponding to the stream index for which the ECPA test was initiated.
1.3.6.1.4.1.2544.1.12.8.1.3.1.1Integer32 (1..3)read-onlycurrent
ecpaTestStreamSourcePort
OBJECT-TYPE
An integer index value corresponding to the ifIndex for which the ECPA test was initiated.
1.3.6.1.4.1.2544.1.12.8.1.3.1.2VariablePointerread-onlycurrent
ecpaTestStreamName
OBJECT-TYPE
Symbolic Stream Name that can be associated with an ECPA stream.
1.3.6.1.4.1.2544.1.12.8.1.3.1.3DisplayString (SIZE(0..64))read-writecurrent
ecpaTestStreamFrameSize
OBJECT-TYPE
This object enables specification of fixed length frame size in bytes for traffic generation. If not specified, default value of 64 bytes is used.
1.3.6.1.4.1.2544.1.12.8.1.3.1.4Integer32 (64..9612)read-writecurrent
ecpaTestStreamRate
OBJECT-TYPE
The object enables specification of the traffic generation rate.
1.3.6.1.4.1.2544.1.12.8.1.3.1.5Unsigned32read-writecurrent
ecpaTestStreamPayloadType
OBJECT-TYPE
This object enables specification of type of payload to generate `fixed' type indicates a generation pattern of 5A, A5, 5A, A5 bytes. `random' type indicates traffic generation with pseudo-random pattern.
1.3.6.1.4.1.2544.1.12.8.1.3.1.6EcpaPayloadTyperead-writecurrent
ecpaTestStreamSignature
OBJECT-TYPE
Indicates an 8-byte signature specified by the user in hexadecimal or ASCII format. This signature is currently used by the FSP150Mx products for test frame recognition and will be appended directly after the ECPA Signature in the test frame and be 4-byte aligned. This will allow the F3 ECPA feature to interoperate with the existing FSP150Mx products. Hexadecimal signature must be prefixed with 0x/0X.
1.3.6.1.4.1.2544.1.12.8.1.3.1.7DisplayString (SIZE(10))read-writecurrent
ecpaTestStreamDestinationMAC
OBJECT-TYPE
Allows specification of destination MAC in the generated traffic.
1.3.6.1.4.1.2544.1.12.8.1.3.1.8MacAddressread-writecurrent
ecpaTestStreamSourceMAC
OBJECT-TYPE
Allows specification of source MAC in the generated traffic.
1.3.6.1.4.1.2544.1.12.8.1.3.1.9MacAddressread-writecurrent
ecpaTestStreamOuterVlanEnabled
OBJECT-TYPE
Allows specification of a VLAN tagged ECPA stream. This variable enables the outer VLAN specification, in the case of a doubly tagged ECPA stream. If a singly tagged ECPA stream is desired, this specification is mandatory.
1.3.6.1.4.1.2544.1.12.8.1.3.1.10TruthValueread-writecurrent
ecpaTestStreamOuterVlanId
OBJECT-TYPE
Outer VLAN Id associated with the ECPA stream. Valid only if ecpaTestStreamOuterVlanEnabled is enabled.
1.3.6.1.4.1.2544.1.12.8.1.3.1.11VlanIdread-writecurrent
ecpaTestStreamOuterVlanPrio
OBJECT-TYPE
Outer VLAN Priority associated with the ECPA stream. Valid only if ecpaTestStreamOuterVlanEnabled is enabled.
1.3.6.1.4.1.2544.1.12.8.1.3.1.12VlanPriorityread-writecurrent
ecpaTestStreamOuterVlanEtherType
OBJECT-TYPE
EtherType associated with the Outer VLAN Tag. Valid only if ecpaTestStreamOuterVlanEnabled is enabled.
1.3.6.1.4.1.2544.1.12.8.1.3.1.13Integer32 (0..65535)read-writecurrent
ecpaTestStreamInnerVlanEnabled
OBJECT-TYPE
Allows specification of a VLAN tagged ECPA stream. This variable enables the outer VLAN specification, in the case of a doubly tagged ECPA stream. If a singly tagged ECPA stream is desired, this specification is mandatory.
1.3.6.1.4.1.2544.1.12.8.1.3.1.14TruthValueread-writecurrent
ecpaTestStreamInnerVlanId
OBJECT-TYPE
Inner VLAN Id associated with the ECPA stream. Valid only if ecpaTestStreamInnerVlanEnabled is enabled.
1.3.6.1.4.1.2544.1.12.8.1.3.1.15VlanIdread-writecurrent
ecpaTestStreamInnerVlanPrio
OBJECT-TYPE
Inner VLAN Priority associated with the ECPA stream. Valid only if ecpaTestStreamInnerVlanEnabled is enabled.
1.3.6.1.4.1.2544.1.12.8.1.3.1.16VlanPriorityread-writecurrent
ecpaTestStreamInnerVlanEtherType
OBJECT-TYPE
EtherType associated with the Inner VLAN Tag. Valid only if ecpaTestStreamInnerVlanEnabled is enabled.
1.3.6.1.4.1.2544.1.12.8.1.3.1.17Integer32 (0..65535)read-writecurrent
ecpaTestStreamIpVersion
OBJECT-TYPE
This object enables specification of IP data in the generated test traffic. Value of `ipv4' allows test data to be IP v4 compatible. Value of `ipv6' allows test data to be IP v6 compatible.
1.3.6.1.4.1.2544.1.12.8.1.3.1.18IpVersionread-writecurrent
ecpaTestStreamIpV4Address
OBJECT-TYPE
This object enables specification of ipv4 IP Address for the test stream.This is used when ecpaTestStreamIpVersion is ipv4.
1.3.6.1.4.1.2544.1.12.8.1.3.1.19IpAddressread-writecurrent
ecpaTestStreamIpV6Address
OBJECT-TYPE
This object enables specification of ipv6 IP Address for the test stream.This is used when ecpaTestStreamIpVersion is ipv6.
1.3.6.1.4.1.2544.1.12.8.1.3.1.20Ipv6Addressread-writecurrent
ecpaTestStreamPrioMapMode
OBJECT-TYPE
This object enables specification of Priority Mapping Mode for the test stream.
1.3.6.1.4.1.2544.1.12.8.1.3.1.21IpPriorityMapModeread-writecurrent
ecpaTestStreamPrioVal
OBJECT-TYPE
This object enables specification of Priority Value for ecpaTestStreamPrioMapMode as TOS/DSCP.
1.3.6.1.4.1.2544.1.12.8.1.3.1.22Integer32 (0..63)read-writecurrent
ecpaTestStreamMonStartTime
OBJECT-TYPE
The start time of the ECPA test for this stream.
1.3.6.1.4.1.2544.1.12.8.1.3.1.23DateAndTimeread-onlycurrent
ecpaTestStreamMonEndTime
OBJECT-TYPE
The end time of the ECPA test for this stream.
1.3.6.1.4.1.2544.1.12.8.1.3.1.24DateAndTimeread-onlycurrent
ecpaTestStreamMonElapsedTime
OBJECT-TYPE
The elapsed time of ECPA test for this stream in seconds.
1.3.6.1.4.1.2544.1.12.8.1.3.1.25Integer32read-onlycurrent
ecpaTestStreamMonTxFrames
OBJECT-TYPE
The total number of frames transmitted(generated) so far. This object does not exist if the ecpaControlTestStatus indicates initial state.
1.3.6.1.4.1.2544.1.12.8.1.3.1.26PerfCounter64read-onlycurrent
ecpaTestStreamMonRxFrames
OBJECT-TYPE
The total number of frames received so far. This object does not exist if the ecpaControlTestStatus indicates initial state.
1.3.6.1.4.1.2544.1.12.8.1.3.1.27PerfCounter64read-onlycurrent
ecpaTestStreamMonRxPercentSuccess
OBJECT-TYPE
Received frames as a percentage of transmitted frames. This object does not exist if the ecpaControlTestStatus indicates initial state.
1.3.6.1.4.1.2544.1.12.8.1.3.1.28Integer32read-onlycurrent
ecpaTestStreamMonRxOutOfSeqErrs
OBJECT-TYPE
The total number of out of sequence errors received so far. This object does not exist if the ecpaControlTestStatus indicates initial state.
1.3.6.1.4.1.2544.1.12.8.1.3.1.29PerfCounter64read-onlycurrent
ecpaTestStreamMonRxSeqGaps
OBJECT-TYPE
The total number of sequence gaps received so far. This object does not exist if the ecpaControlTestStatus indicates initial state.
1.3.6.1.4.1.2544.1.12.8.1.3.1.30PerfCounter64read-onlycurrent
ecpaTestStreamMonRxNonEcpaFrames
OBJECT-TYPE
The total number of non ECPA frames received during the execution.
1.3.6.1.4.1.2544.1.12.8.1.3.1.31PerfCounter64read-onlycurrent
ecpaTestStreamMonRxMinDelay
OBJECT-TYPE
The minimum delay (in microseconds) across all frames received so far. This object does not exist if the ecpaControlTestStatus indicates initial state.
1.3.6.1.4.1.2544.1.12.8.1.3.1.32Unsigned32read-onlycurrent
ecpaTestStreamMonRxMaxDelay
OBJECT-TYPE
The maximum delay (in microseconds) across all frames received so far. This object does not exist if the ecpaControlTestStatus indicates initial state.
1.3.6.1.4.1.2544.1.12.8.1.3.1.33Unsigned32read-onlycurrent
ecpaTestStreamMonRxAvgDelay
OBJECT-TYPE
The average delay (in microseconds) across all frames received so far. This object does not exist if the ecpaControlTestStatus indicates initial state.
1.3.6.1.4.1.2544.1.12.8.1.3.1.34Unsigned32read-onlycurrent
ecpaTestStreamMonRx1stFrameSize
OBJECT-TYPE
Frame size of the Monitored First Frame.
1.3.6.1.4.1.2544.1.12.8.1.3.1.35Integer32 (64..9612)read-onlycurrent
ecpaTestStreamMonRx1stFrame1Octets
OBJECT-TYPE
The frame contents of the first received frame - first 1024 bytes. This object does not exist if the ecpaControlTestStatus indicates initial state.
1.3.6.1.4.1.2544.1.12.8.1.3.1.36DisplayString (SIZE(1..2048))read-onlycurrent
ecpaTestStreamMonRx1stFrame2Octets
OBJECT-TYPE
The frame contents of the first received frame - next 1024 bytes. This object does not exist if the ecpaControlTestStatus indicates initial state.
1.3.6.1.4.1.2544.1.12.8.1.3.1.37DisplayString (SIZE(1..2048))read-onlycurrent
ecpaTestStreamMonRx1stFrame3Octets
OBJECT-TYPE
The frame contents of the first received frame - next 1024 bytes. This object does not exist if the ecpaControlTestStatus indicates initial state.
1.3.6.1.4.1.2544.1.12.8.1.3.1.38DisplayString (SIZE(1..2048))read-onlycurrent
ecpaTestStreamMonRx1stFrame4Octets
OBJECT-TYPE
The frame contents of the first received frame - next 1024 bytes. This object does not exist if the ecpaControlTestStatus indicates initial state.
1.3.6.1.4.1.2544.1.12.8.1.3.1.39DisplayString (SIZE(1..2048))read-onlycurrent
ecpaTestStreamMonRx1stFrame5Octets
OBJECT-TYPE
The frame contents of the first received frame - next 1024 bytes. This object does not exist if the ecpaControlTestStatus indicates initial state.
1.3.6.1.4.1.2544.1.12.8.1.3.1.40DisplayString (SIZE(1..2048))read-onlycurrent
ecpaTestStreamMonRx1stFrame6Octets
OBJECT-TYPE
The frame contents of the first received frame - next 1024 bytes. This object does not exist if the ecpaControlTestStatus indicates initial state.
1.3.6.1.4.1.2544.1.12.8.1.3.1.41DisplayString (SIZE(1..2048))read-onlycurrent
ecpaTestStreamMonRx1stFrame7Octets
OBJECT-TYPE
The frame contents of the first received frame - next 1024 bytes. This object does not exist if the ecpaControlTestStatus indicates initial state.
1.3.6.1.4.1.2544.1.12.8.1.3.1.42DisplayString (SIZE(1..2048))read-onlycurrent
ecpaTestStreamMonRx1stFrame8Octets
OBJECT-TYPE
The frame contents of the first received frame - next 1024 bytes. This object does not exist if the ecpaControlTestStatus indicates initial state.
1.3.6.1.4.1.2544.1.12.8.1.3.1.43DisplayString (SIZE(1..2048))read-onlycurrent
ecpaTestStreamMonRx1stFrame9Octets
OBJECT-TYPE
The frame contents of the first received frame - next 1024 bytes. This object does not exist if the ecpaControlTestStatus indicates initial state.
1.3.6.1.4.1.2544.1.12.8.1.3.1.44DisplayString (SIZE(1..2048))read-onlycurrent
ecpaTestStreamMonRx1stFrame10Octets
OBJECT-TYPE
The frame contents of the first received frame - next 1024 bytes. This object does not exist if the ecpaControlTestStatus indicates initial state.
1.3.6.1.4.1.2544.1.12.8.1.3.1.45DisplayString (SIZE(1..2048))read-onlycurrent
ecpaTestStreamMonRxBitRate
OBJECT-TYPE
The object provides the average bit rate on the ECPA test stream.
1.3.6.1.4.1.2544.1.12.8.1.3.1.46PerfCounter64read-onlycurrent
ecpaTestStreamInnerVlan2Enabled
OBJECT-TYPE
This variable indicates the second(inner) VLAN specification, in the case of a 3-tagged ECPA stream. If a three tagged ECPA stream is desired, this indicates true.
1.3.6.1.4.1.2544.1.12.8.1.3.1.47TruthValueread-onlycurrent
ecpaTestStreamInnerVlan2Id
OBJECT-TYPE
This variable provides the Inner (second) VLAN Id associated with the ECPA stream. Valid only if ecpaTestStreamInnerVlan2Enabled is enabled.
1.3.6.1.4.1.2544.1.12.8.1.3.1.48VlanIdread-onlycurrent
ecpaTestStreamInnerVlan2Prio
OBJECT-TYPE
This variable provides the Inner (second) VLAN Priority associated with the ECPA stream. Valid only if ecpaTestStreamInnerVlan2Enabled is enabled.
1.3.6.1.4.1.2544.1.12.8.1.3.1.49VlanPriorityread-onlycurrent
ecpaTestStreamInnerVlan2EtherType
OBJECT-TYPE
This variable provides the EtherType associated with the Inner (second) VLAN Tag. Valid only if ecpaTestStreamInnerVlan2Enabled is enabled.
1.3.6.1.4.1.2544.1.12.8.1.3.1.50Integer32 (0..65535)read-onlycurrent
ecpaTestStreamDestIpV4Address
OBJECT-TYPE
This object provides the destination ipv4 IP Address for the test stream. This is valid when ecpaTestStreamIpVersion is ipv4.
1.3.6.1.4.1.2544.1.12.8.1.3.1.51IpAddressread-onlycurrent
ecpaTestStreamDestIpV6Address
OBJECT-TYPE
This object provides the destination ipv6 IP Address for the test stream. This is valid when ecpaTestStreamIpVersion is ipv6.
1.3.6.1.4.1.2544.1.12.8.1.3.1.52Ipv6Addressread-onlycurrent
ecpaTestStreamConfigChanged
OBJECT-TYPE
This object provides information on whether the associated ecpaConfigStream is changed.
1.3.6.1.4.1.2544.1.12.8.1.3.1.53TruthValueread-onlycurrent
ecpaTestStreamRateHi
OBJECT-TYPE
The object enables specification of the higher 32 bits of the traffic generation rate.
1.3.6.1.4.1.2544.1.12.8.1.3.1.54Unsigned32read-writecurrent
ecpaTestStreamUdpControl
OBJECT-TYPE
This object enables or disables UDP header.
1.3.6.1.4.1.2544.1.12.8.1.3.1.55TruthValueread-writecurrent
ecpaTestStreamUdpSrcPort
OBJECT-TYPE
When UDP control is enabled, this object provides the UDP source port. Otherwize it is ignored.
1.3.6.1.4.1.2544.1.12.8.1.3.1.56Integer32 (1..65535)read-writecurrent
ecpaTestStreamUdpDstPort
OBJECT-TYPE
When UDP control is enabled, this object provides the UDP destination port. Otherwize it is ignored.
1.3.6.1.4.1.2544.1.12.8.1.3.1.57Integer32 (1..65535)read-writecurrent
esaProbeTable
OBJECT-TYPE
A list of entries corresponding to ESA Probes.
1.3.6.1.4.1.2544.1.12.8.1.4not-accessiblecurrent
esaProbeEntry
OBJECT-TYPE
A row in the esaProbeTable. Entries can be created in this table by management application action. The slotIndex should be 255 if the product is cm5.1.
1.3.6.1.4.1.2544.1.12.8.1.4.1not-accessiblecurrent
esaProbeIndex
OBJECT-TYPE
An integer index value used to uniquely identify this ESA Probe within a Card.
1.3.6.1.4.1.2544.1.12.8.1.4.1.1Integer32read-onlycurrent
esaProbeName
OBJECT-TYPE
A unique identifier used by the Manager to distinguish the ESA Probe.
1.3.6.1.4.1.2544.1.12.8.1.4.1.2DisplayString (SIZE(1..15))read-createcurrent
esaProbeSourcePort
OBJECT-TYPE
This object points to the Port to which the ESA Probe is attached, i.e.on which the service to be monitored resides.
1.3.6.1.4.1.2544.1.12.8.1.4.1.3VariablePointerread-createcurrent
esaProbeAssocSchedGroup
OBJECT-TYPE
This object points to the probe's associated Scheduled Group. Initially, when the probe is not associated with a Group, this object's value is set to {0.0}.
1.3.6.1.4.1.2544.1.12.8.1.4.1.4VariablePointerread-onlycurrent
esaProbeDirection
OBJECT-TYPE
This object allows to specify the direction of Probe traffic generation.
1.3.6.1.4.1.2544.1.12.8.1.4.1.5EsaProbeDirectionread-createcurrent
esaProbeProtocol
OBJECT-TYPE
Protocol to be used in ESA Probe messages. 'icmpTimestamp', 'icmpEcho', 'udpEcho' protocols support layer-3 ethernet service assurance. If the remote reflector is an ADVA equipment based on CM family of products, one-way loss measurement, one-way delay measurement, round-trip delay measurement and one-way jitter measurements are computed. Else, only round-trip delay measurements are applicable. 'y1731' protocol can be used for layer-2 ethernet service assurance. One-way loss measurement, one-way and round-trip delay measurement, and one-way jitter measurements are available for this protocol. 'y1731-slm-slr' protocol can be used for layer-2 ethernet service assurance using Synthetic Loss Measurement messages. One-way loss measurement, one-way and round-trip delay measurement, and one-way jitter measurements are available for this protocol.
1.3.6.1.4.1.2544.1.12.8.1.4.1.6EsaProbeProtocolread-createcurrent
esaProbeSrcIpAddress
OBJECT-TYPE
Variable that allows specification of the Probe's source IP Address. This IP Address is used in the IP header of the ESA Probe generated packets, as source address. NOTE: This attribute is not applicable to Y.1731 probes.
1.3.6.1.4.1.2544.1.12.8.1.4.1.7IpAddressread-createcurrent
esaProbeSrcSubnetMask
OBJECT-TYPE
Variable that allows specification of the Probe's source IP Subnet Mask. NOTE: This attribute is not applicable to Y.1731 probes.
1.3.6.1.4.1.2544.1.12.8.1.4.1.8IpAddressread-createcurrent
esaProbeDestIpAddress
OBJECT-TYPE
Variable that allows specification of the Reflector's destination IP Address. This IP Address is used in the IP header of the ESA Probe generated packets, as destination address. NOTE: This attribute is not applicable to Y.1731 probes.
1.3.6.1.4.1.2544.1.12.8.1.4.1.9IpAddressread-createcurrent
esaProbeSrcMep
OBJECT-TYPE
This attribute is applicable only for Y.1731 probes. It identifies the source MEP that initiates the Y.1731 LMMs and DMMs.
1.3.6.1.4.1.2544.1.12.8.1.4.1.10VariablePointerread-createcurrent
esaProbeDestMepType
OBJECT-TYPE
This attribute is applicable only for Y.1731 probes. This indicates if the destination MEP is specified using the MEP ID object esaProbeDestMepId.
1.3.6.1.4.1.2544.1.12.8.1.4.1.11MepDestinationTyperead-createcurrent
esaProbeDestMepMacAddr
OBJECT-TYPE
This attribute is applicable only for Y.1731 probes. It identifies the destination MEP that responds to the LMMs and DMMs. This MAC address will be the destination MAC address for LMM and DMM frames if esaProbeY1731DestMepType is 'macaddress'. If CC protocol is not enabled between source and destination MEP then this is the only choice to identify the remote MEP.
1.3.6.1.4.1.2544.1.12.8.1.4.1.12MacAddressread-createcurrent
esaProbeDestMepId
OBJECT-TYPE
This attribute is applicable only for Y.1731 probes. It identifies the destination MEP that responds to the LMMs and DMMs. The MAC address of this RMEP ID from RMEP database will be the destination MAC address for LMM and DMM. This value is used only if the esaProbeY1731DestMepType is 'mepid'. CC protocol must be enabled between source and destination MEP if the RMEP ID is used to identify the Remote MEP.
1.3.6.1.4.1.2544.1.12.8.1.4.1.13Dot1agCfmMepIdOrZeroread-createcurrent
esaProbeVlanTagEnabled
OBJECT-TYPE
Ability to specify whether or not to use VLAN tagged or untagged ESA traffic generation on the Probe. NOTE: This attribute is not applicable to Y.1731 probes.
1.3.6.1.4.1.2544.1.12.8.1.4.1.14TruthValueread-writecurrent
esaProbeVlanTagEtherType
OBJECT-TYPE
This variable allows the user to specify the monitored service's VLAN tag Ether Type. Valid if 'esaProbeVlanTagEnabled' is specified as TRUE. NOTE: This attribute is not applicable to Y.1731 probes.
1.3.6.1.4.1.2544.1.12.8.1.4.1.15Unsigned32read-writecurrent
esaProbeVlanId
OBJECT-TYPE
This variable allows the user to specify the monitored service's VLAN tag. Valid if 'esaProbeVlanTagEnabled' is specified as TRUE. NOTE: This attribute is not applicable to Y.1731 probes.
1.3.6.1.4.1.2544.1.12.8.1.4.1.16VlanIdread-writecurrent
esaProbeVlanPrio
OBJECT-TYPE
This variable allows the user to specify the monitored service's VLAN priority. Valid if 'esaProbeVlanTagEnabled' is specified as TRUE. NOTE: This attribute is not applicable to Y.1731 probes.
1.3.6.1.4.1.2544.1.12.8.1.4.1.17VlanPriorityread-writecurrent
esaProbeInnerVlanTagEnabled
OBJECT-TYPE
Ability to specify whether or not to use Inner VLAN tag. NOTE: This attribute is not applicable to Y.1731 probes.
1.3.6.1.4.1.2544.1.12.8.1.4.1.18TruthValueread-writecurrent
esaProbeInnerVlanTagEtherType
OBJECT-TYPE
This variable allows the user to specify the monitored service's Inner VLAN tag Ether Type. Valid if 'esaProbeInnerVlanTagEnabled' is specified as TRUE. NOTE: This attribute is not applicable to Y.1731 probes.
1.3.6.1.4.1.2544.1.12.8.1.4.1.19Unsigned32read-writecurrent
esaProbeInnerVlanId
OBJECT-TYPE
This variable allows the user to specify the monitored service's Inner VLAN tag. Valid if 'esaProbeInnerVlanTagEnabled' is specified as TRUE. NOTE: This attribute is not applicable to Y.1731 probes.
1.3.6.1.4.1.2544.1.12.8.1.4.1.20VlanIdread-writecurrent
esaProbeInnerVlanPrio
OBJECT-TYPE
This variable allows the user to specify the monitored service's Inner VLAN priority. Valid if 'esaProbeInnerVlanTagEnabled' is specified as TRUE. NOTE: This attribute is not applicable to Y.1731 probes.
1.3.6.1.4.1.2544.1.12.8.1.4.1.21VlanPriorityread-writecurrent
esaProbeIpPrioMapMode
OBJECT-TYPE
This object enables specification of Priority Mapping Mode for the ESA Probe. NOTE: This attribute is not applicable to Y.1731 probes.
1.3.6.1.4.1.2544.1.12.8.1.4.1.22IpPriorityMapModeread-writecurrent
esaProbeIpPriority
OBJECT-TYPE
This object enables specification of Priority Value for esaProbePrioMapMode as priomap-tos,priomap-dscp. NOTE: This attribute is not applicable to Y.1731 probes.
1.3.6.1.4.1.2544.1.12.8.1.4.1.23Integer32 (0..63)read-writecurrent
esaProbePktsPerSample
OBJECT-TYPE
This object enables specification of number of packets within a sample run for ESA traffic generation. A non-zero value must be specified. NOTE: This attribute is not applicable to Y.1731 probes.
1.3.6.1.4.1.2544.1.12.8.1.4.1.24Integer32read-writecurrent
esaProbePktSize
OBJECT-TYPE
This object enables specification of fixed length frame size in bytes for ESA traffic generation. If not specified, default value of 104 bytes is used. NOTE: This attribute is not available to Y.1731 probes.
1.3.6.1.4.1.2544.1.12.8.1.4.1.25Integer32 (0 | 64..2000)read-writecurrent
esaProbeInterPktGap
OBJECT-TYPE
This object enables specification of interval in milliseconds between packet generation. A non-zero value must be specified. NOTE: This attribute is not applicable to Y.1731 probes.
1.3.6.1.4.1.2544.1.12.8.1.4.1.26Integer32read-writecurrent
esaProbePktDeadInterval
OBJECT-TYPE
This object enables specification of the dead interval in seconds after 'esaProbePktsPerSample' have been generated within the sample. This allows for settling time of the ESA traffic. A non-zero value must be specified. NOTE: This attribute is not applicable to Y.1731 probes.
1.3.6.1.4.1.2544.1.12.8.1.4.1.27Integer32read-writecurrent
esaProbeResponseTimeout
OBJECT-TYPE
This object allows specification of the timeout value to determine lost packets. Time specified in seconds. NOTE: This attribute is not applicable to Y.1731 probes. This object is applicable to Layer 3 and SLM/SLR Probes.
1.3.6.1.4.1.2544.1.12.8.1.4.1.28Integer32read-writecurrent
esaProbeY1731DmmPktSize
OBJECT-TYPE
This object is only applicable to Y.1731 probes. This object enables specification of the TLV size for Delay Measurement Frames (DMMs). Value of 0 is a read-only value when the Probe protocol is not y1731. GE206 Release 4.4.x supports 2000 bytes
1.3.6.1.4.1.2544.1.12.8.1.4.1.29Integer32 (0 | 64..9600)read-writecurrent
esaProbeY1731LmmInterval
OBJECT-TYPE
LMM frame transmission period. For Loss Measurement Frames, only interval-1sec is supported. This attribute is only applicable to Y.1731 probes.
1.3.6.1.4.1.2544.1.12.8.1.4.1.30EsaProbePktIntervalTyperead-createcurrent
esaProbeY1731DmmInterval
OBJECT-TYPE
DMM frame transmission period. This attribute is only applicable to Y.1731 probes.
1.3.6.1.4.1.2544.1.12.8.1.4.1.31EsaProbePktIntervalTyperead-createcurrent
esaProbeHistoryBins
OBJECT-TYPE
This object allows specification of number of history bins. This is the total history data that will be maintained for an ESA Probe run, at any instance.
1.3.6.1.4.1.2544.1.12.8.1.4.1.32Integer32 (0..32)read-writecurrent
esaProbeHistoryInterval
OBJECT-TYPE
This object allows specification of the history interval period.
1.3.6.1.4.1.2544.1.12.8.1.4.1.33EsaProbeHistoryIntervalTyperead-writecurrent
esaProbeDistHistoryBins
OBJECT-TYPE
This object allows specification of number of distribution history bins. This is the total history distribution data that will be maintained for an ESA Probe run, at any instance.
1.3.6.1.4.1.2544.1.12.8.1.4.1.34Integer32 (0..32)read-writecurrent
esaProbeDistHistoryInterval
OBJECT-TYPE
This object allows specification of the history distribution interval period.
1.3.6.1.4.1.2544.1.12.8.1.4.1.35EsaProbeHistoryIntervalTyperead-writecurrent
esaProbeCreationTime
OBJECT-TYPE
This object provides the creation time of the ESA Probe.
1.3.6.1.4.1.2544.1.12.8.1.4.1.36DateAndTimeread-onlycurrent
esaProbeStorageType
OBJECT-TYPE
The type of storage configured for this entry.
1.3.6.1.4.1.2544.1.12.8.1.4.1.37StorageTyperead-createcurrent
esaProbeRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of esaProbeRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with esaProbeRowStatus value as createAndGo(4). Upon successful row creation, this variable has a value of active(1). The esaProbeRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.8.1.4.1.38RowStatusread-createcurrent
esaProbeMultiCOSEnabled
OBJECT-TYPE
This object is introduced for FSP150CC Release 4.3. This object is only applicable for Y.1731 and SLM-SLR Probe Protocol Types. This object can be used to specify the multiple class of services (COS) for each ESA Probe.
1.3.6.1.4.1.2544.1.12.8.1.4.1.39TruthValueread-createcurrent
esaProbeSLAMonitorType
OBJECT-TYPE
This object indicates whether the Probe is a point-to-point type or a point-to-multipoint type. Only SLM-SLR probes can be point-to-multipoint.
1.3.6.1.4.1.2544.1.12.8.1.4.1.40EsaProbeSLAMonitorTyperead-createcurrent
esaProbeCOSType
OBJECT-TYPE
This object can be used to specify the first Class of Service associated with the Y.1731/SLM-SLR ESA Probe. In the case of a multiCOS Probe, this object has no semantics when multiple COS levels exist. This object is only valid for Y.1731/SLM-SLR ESA Probes.
1.3.6.1.4.1.2544.1.12.8.1.4.1.41ClassOfServiceTyperead-createcurrent
esaProbeSLMMulticastMACEnabled
OBJECT-TYPE
This object can be used to specify whether the SLM/SLR protocol Probe will use multicast MAC address in SLM (Synthetic Loss Measurement) messages. This object is only valid for SLM-SLR ESA Probes.
1.3.6.1.4.1.2544.1.12.8.1.4.1.42TruthValueread-createcurrent
esaProbeSOAMInterval
OBJECT-TYPE
This object can be used to specify the packet interval type for Y.1731 LM/DM and SLM/SLR based ESA Probes, for the first Class of Service. In the case of a multiCOS Probe, this object has no semantics when multiple COS levels exist. This attribute is applicable for Y.1731 LM/DM and SLM/SLR based probes.
1.3.6.1.4.1.2544.1.12.8.1.4.1.43EsaProbePktIntervalTyperead-createcurrent
esaProbeSOAMPktSize
OBJECT-TYPE
This object can be used to specify the packet size for SLM-SLR based ESA Probes, for the first Class of Service. In the case of multiCOS Probe, this object has no semantics when multiple COS levels exist. In such cases this will return a value of 0.
1.3.6.1.4.1.2544.1.12.8.1.4.1.44Integer32 (0 | 64..9612)read-writecurrent
esaProbeInner2VlanTagEnabled
OBJECT-TYPE
Ability to specify whether or not to use Inner2 VLAN tag. NOTE: This attribute is not applicable to Y.1731 probes.
1.3.6.1.4.1.2544.1.12.8.1.4.1.45TruthValueread-writecurrent
esaProbeInner2VlanTagEtherType
OBJECT-TYPE
This variable allows the user to specify the monitored service's Inner2 VLAN tag Ether Type. Valid if 'esaProbeInner2VlanTagEnabled' is specified as TRUE. NOTE: This attribute is not applicable to Y.1731 probes.
1.3.6.1.4.1.2544.1.12.8.1.4.1.46Unsigned32read-writecurrent
esaProbeInner2VlanId
OBJECT-TYPE
This variable allows the user to specify the monitored service's Inner2 VLAN tag. Valid if 'esaProbeInner2VlanTagEnabled' is specified as TRUE. NOTE: This attribute is not applicable to Y.1731 probes.
1.3.6.1.4.1.2544.1.12.8.1.4.1.47VlanIdread-writecurrent
esaProbeInner2VlanPrio
OBJECT-TYPE
This variable allows the user to specify the monitored service's Inner2 VLAN priority. Valid if 'esaProbeInner2VlanTagEnabled' is specified as TRUE. NOTE: This attribute is not applicable to Y.1731 probes.
1.3.6.1.4.1.2544.1.12.8.1.4.1.48VlanPriorityread-writecurrent
esaProbeAdminState
OBJECT-TYPE
This object represents the Administrative State of the ESA Probe. This is not externally managed.
1.3.6.1.4.1.2544.1.12.8.1.4.1.49AdminStateread-onlycurrent
esaProbeOperationalState
OBJECT-TYPE
This object represents the Operational State of the ESA Probe.
1.3.6.1.4.1.2544.1.12.8.1.4.1.50OperationalStateread-onlycurrent
esaProbeSecondaryState
OBJECT-TYPE
This object represents the Secondary State of the ESA Probe.
1.3.6.1.4.1.2544.1.12.8.1.4.1.51SecondaryStateread-onlycurrent
esaProbeMacAddress
OBJECT-TYPE
This attribute is applicable only for Y.1731 probes. It identifies the destination MacAddress which esa using
1.3.6.1.4.1.2544.1.12.8.1.4.1.52MacAddressread-onlycurrent
esaProbeAlias
OBJECT-TYPE
This object allows SNMP management entities to provide an alias for an ESA Probe.
1.3.6.1.4.1.2544.1.12.8.1.4.1.53DisplayString (SIZE(0..128))read-createcurrent
esaProbeScheduleGroupTable
OBJECT-TYPE
A list of entries that allow groups of ESA Probes to be scheduled.
1.3.6.1.4.1.2544.1.12.8.1.5not-accessiblecurrent
esaProbeScheduleGroupEntry
OBJECT-TYPE
A row in esaProbeScheduleGroupTable. Entries are created in this table by management application action.
1.3.6.1.4.1.2544.1.12.8.1.5.1not-accessiblecurrent
esaProbeScheduleGroupIndex
OBJECT-TYPE
A unique index to distinguish the ESA Probe Schedule Group.
1.3.6.1.4.1.2544.1.12.8.1.5.1.1Integer32read-createcurrent
esaProbeScheduleGroupDescr
OBJECT-TYPE
Description of the probe schedule group.
1.3.6.1.4.1.2544.1.12.8.1.5.1.2DisplayString (SIZE(1..256))read-createcurrent
esaProbeScheduleGroupProbeList
OBJECT-TYPE
A comma separated list of esaProbeName's, that will have the same schedule.
1.3.6.1.4.1.2544.1.12.8.1.5.1.3DisplayString (SIZE(1..512))read-createcurrent
esaProbeScheduleGroupType
OBJECT-TYPE
This object allows to specify whether the ESA probe group schedule is 'one-shot' or 'periodic'. A 'one-shot' schedule executes only once and then stops. A 'periodic' schedule reoccurs every 'esaProbeScheduleGroupInterval' seconds and continues until explicitly stopped.
1.3.6.1.4.1.2544.1.12.8.1.5.1.4ScheduleTyperead-createcurrent
esaProbeScheduleGroupStartTime
OBJECT-TYPE
This object allows specification of the start time of the ESA Probe Group. Value of time less than current system time will equate to current time. When the system time reaches this configured time, the ESA Probe Group will be activated.
1.3.6.1.4.1.2544.1.12.8.1.5.1.5DateAndTimeread-createcurrent
esaProbeScheduleGroupDuration
OBJECT-TYPE
This object allows specification of the duration in 'seconds' for ESA Probe Group run. Note that a value of 4294967295 means Duration as FOREVER. FOREVER value is only applicable to schedule type oneshot. The value 4294967295 cannot be used if schedule type is periodic.
1.3.6.1.4.1.2544.1.12.8.1.5.1.6Unsigned32read-createcurrent
esaProbeScheduleGroupInterval
OBJECT-TYPE
This object allows specification of the interval in 'seconds' between successive runs for ESA Probe Group. This variable is only valid if the 'esaProbeScheduleGroupType' is 'periodic'.
1.3.6.1.4.1.2544.1.12.8.1.5.1.7Unsigned32read-createcurrent
esaProbeScheduleGroupAction
OBJECT-TYPE
This object allows to suspend/resume the ESA scheduled group.
1.3.6.1.4.1.2544.1.12.8.1.5.1.8EsaActionread-writecurrent
esaProbeScheduleGroupStatus
OBJECT-TYPE
This object indicates the current status of the ESA Probe Group.
1.3.6.1.4.1.2544.1.12.8.1.5.1.9SchedActivityStatusread-onlycurrent
esaProbeScheduleGroupStorageType
OBJECT-TYPE
The type of storage configured for this entry.
1.3.6.1.4.1.2544.1.12.8.1.5.1.10StorageTyperead-createcurrent
esaProbeScheduleGroupRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of esaProbeScheduleGroupRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with esaProbeRowStatus value as createAndGo(4). Upon successful row creation, this variable has a value of active(1). The esaProbeScheduleGroupRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.8.1.5.1.11RowStatusread-createcurrent
esaProbeScheduleGroupActionProbeList
OBJECT-TYPE
A comma separated list of esaProbeName's, if set esaProbeScheduleGroupAction as add or remove, they will be add or remove from esaProbeScheduleGroupProbeList.
1.3.6.1.4.1.2544.1.12.8.1.5.1.12DisplayString (SIZE(1..512))read-writecurrent
esaReflectorTable
OBJECT-TYPE
A list of entries corresponding to ESA Reflectors. NOTE: There is no need to create reflectors for Y.1731 probes as the MEPs will respond by default.
1.3.6.1.4.1.2544.1.12.8.1.6not-accessiblecurrent
esaReflectorEntry
OBJECT-TYPE
A row in the esaReflectorTable. Entries can be created in this table by management application action.
1.3.6.1.4.1.2544.1.12.8.1.6.1not-accessiblecurrent
esaReflectorIndex
OBJECT-TYPE
A unique index to distinguish the ESA Reflector.
1.3.6.1.4.1.2544.1.12.8.1.6.1.1Integer32read-createcurrent
esaReflectorName
OBJECT-TYPE
A unique identifier to distinguish the ESA Reflector.
1.3.6.1.4.1.2544.1.12.8.1.6.1.2DisplayString (SIZE(1..15))read-createcurrent
esaReflectorIpAddress
OBJECT-TYPE
This object allows specification of the Reflector's IP Address. Reflector listens for packets destined at this IP Address.
1.3.6.1.4.1.2544.1.12.8.1.6.1.3IpAddressread-createcurrent
esaReflectorSubnetMask
OBJECT-TYPE
This object allows specification of the Reflector's IP Subnet mask.
1.3.6.1.4.1.2544.1.12.8.1.6.1.4IpAddressread-createcurrent
esaReflectorSourcePort
OBJECT-TYPE
This object points to the Port to which the ESA Reflector is attached, i.e.on which the service to be monitored resides.
1.3.6.1.4.1.2544.1.12.8.1.6.1.5VariablePointerread-createcurrent
esaReflectorIpPrioMapMode
OBJECT-TYPE
This object enables specification of Priority Mapping Mode for the ESA Reflector.
1.3.6.1.4.1.2544.1.12.8.1.6.1.6IpPriorityMapModeread-writecurrent
esaReflectorIpPriority
OBJECT-TYPE
This object enables specification of Priority Value for esaReflectorPrioMapMode as priomap-tos,priomap-dscp.
1.3.6.1.4.1.2544.1.12.8.1.6.1.7Integer32 (0..63)read-writecurrent
esaReflectorAction
OBJECT-TYPE
This object allows to suspend/resume the ESA reflector.
1.3.6.1.4.1.2544.1.12.8.1.6.1.8EsaActionread-writecurrent
esaReflectorSuspended
OBJECT-TYPE
This object indicates whether the ESA Reflector is active or suspended.
1.3.6.1.4.1.2544.1.12.8.1.6.1.9TruthValueread-onlycurrent
esaReflectorCreationTime
OBJECT-TYPE
This object provides the creation time of the ESA Reflector.
1.3.6.1.4.1.2544.1.12.8.1.6.1.10DateAndTimeread-onlycurrent
esaReflectorStorageType
OBJECT-TYPE
The type of storage configured for this entry.
1.3.6.1.4.1.2544.1.12.8.1.6.1.11StorageTyperead-createcurrent
esaReflectorRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of esaReflectorRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with esaReflectorRowStatus value as createAndGo(4). Upon successful row creation, this variable has a value of active(1). The esaReflectorRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.8.1.6.1.12RowStatusread-createcurrent
esaReflectorDirection
OBJECT-TYPE
This object provides the direction of the ESA Reflector.
1.3.6.1.4.1.2544.1.12.8.1.6.1.13EsaReflectorDirectionread-createcurrent
esaReflectorAdminState
OBJECT-TYPE
This object represents the Administrative State of the ESA Reflector. This is not externally managed.
1.3.6.1.4.1.2544.1.12.8.1.6.1.14AdminStateread-onlycurrent
esaReflectorOperationalState
OBJECT-TYPE
This object represents the Operational State of the ESA Reflector.
1.3.6.1.4.1.2544.1.12.8.1.6.1.15OperationalStateread-onlycurrent
esaReflectorSecondaryState
OBJECT-TYPE
This object represents the Secondary State of the ESA Reflector.
1.3.6.1.4.1.2544.1.12.8.1.6.1.16SecondaryStateread-onlycurrent
esaReflectorMacAddress
OBJECT-TYPE
This attribute is applicable only for Y.1731 probes. It identifies the destination MacAddress which esa using
1.3.6.1.4.1.2544.1.12.8.1.6.1.17MacAddressread-onlycurrent
esaReflectorAlias
OBJECT-TYPE
This object allows SNMP management entities to provide an alias for an ESA Reflector.
1.3.6.1.4.1.2544.1.12.8.1.6.1.18DisplayString (SIZE(0..128))read-createcurrent
esaProbeStatsTable
OBJECT-TYPE
A collection of ESA Probe related statistics kept for a particular ESA Probe entity. These reflect the current data.
1.3.6.1.4.1.2544.1.12.8.1.7not-accessiblecurrent
esaProbeStatsEntry
OBJECT-TYPE
A conceptual row in the esaProbeStatsTable. An entry exists in this table for each ESA Probe.
1.3.6.1.4.1.2544.1.12.8.1.7.1not-accessiblecurrent
esaProbeStatsDestinationIndex
OBJECT-TYPE
An integer index value used to uniquely identify a destination (Reflector) Index, in a point-to-multi point SLA. For Release 4.1 GE206, this value is 1, since only point-to-point SLA is supported.
1.3.6.1.4.1.2544.1.12.8.1.7.1.1Integer32read-onlycurrent
esaProbeStatsCOSIndex
OBJECT-TYPE
An integer index value used to uniquely identify SLA for a specific Class of Service. For Release 4.1 GE206, this value is 1, since the COS is explicitly specified in the Probe parameters.
1.3.6.1.4.1.2544.1.12.8.1.7.1.2Integer32read-onlycurrent
esaProbeStatsIndex
OBJECT-TYPE
An arbitrary integer index value used to uniquely identify this ESA Probe statistics entry. Index 1 corresponds to current and index 2 to rollover.
1.3.6.1.4.1.2544.1.12.8.1.7.1.3Integer32 (1..2)read-onlycurrent
esaProbeStatsIntervalType
OBJECT-TYPE
Indicates the type of collection, i.e. whether it is current, or rollover.
1.3.6.1.4.1.2544.1.12.8.1.7.1.4EsaProbePmIntervalTyperead-onlycurrent
esaProbeStatsCOS
OBJECT-TYPE
The Class of Service. For Release 4.1 GE206, this value is cos-not-applicable, since multi COS SLA is not supported.
1.3.6.1.4.1.2544.1.12.8.1.7.1.5ClassOfServiceTyperead-onlycurrent
esaProbeStatsValid
OBJECT-TYPE
Indicates the validity of the bin.
1.3.6.1.4.1.2544.1.12.8.1.7.1.6TruthValueread-onlycurrent
esaProbeStatsAction
OBJECT-TYPE
Allows the Manager to clear the bin.
1.3.6.1.4.1.2544.1.12.8.1.7.1.7CmPmBinActionread-writecurrent
esaProbeStatsP2RPkts
OBJECT-TYPE
The total number of Transmitted Packets in the current interval. In the case of Y.1731 probes, this reflects the number of DMRs (Delay Measurement Replies) received and this will always be the same as the esaProbeStatsR2PPkts.
1.3.6.1.4.1.2544.1.12.8.1.7.1.8PerfCounter64read-onlycurrent
esaProbeStatsP2RErredPkts
OBJECT-TYPE
The total number of Packets in the current interval, for which there was a problem in transmission. This error is counted when there is a failure in packet transmission due to resource limitations (buffers). This can happen if the Probe Configuration was changed to send in a large number of packets in a time interval. NOTE: This is not applicable for Y.1731 probes.
1.3.6.1.4.1.2544.1.12.8.1.7.1.9PerfCounter64read-onlycurrent
esaProbeStatsP2RSyncErrs
OBJECT-TYPE
The number of (time) Synchronization Errors from probe to reflector in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.7.1.10PerfCounter64read-onlycurrent
esaProbeStatsP2RLostPkts
OBJECT-TYPE
The number of Lost Pkts from probe to reflector in the current interval. For Y.1731 probes, these are the actual data frames lost.
1.3.6.1.4.1.2544.1.12.8.1.7.1.11PerfCounter64read-onlycurrent
esaProbeStatsR2PPkts
OBJECT-TYPE
The total number of Received Packets in the current interval. In the case of Y.1731 probes, this reflects the number of DMRs (Delay Measurement Replies) received and this will always be the same as the esaProbeStatsP2RPkts.
1.3.6.1.4.1.2544.1.12.8.1.7.1.12PerfCounter64read-onlycurrent
esaProbeStatsR2PErredPkts
OBJECT-TYPE
The total number of Received Packets in the current interval, which had errors such as length of received packet is less than the protocol header length, packet was received after it was marked as lost (i.e.beyond timeout). NOTE: This is not applicable for Y.1731 probes.
1.3.6.1.4.1.2544.1.12.8.1.7.1.13PerfCounter64read-onlycurrent
esaProbeStatsR2PSyncErrs
OBJECT-TYPE
The number of (time) Synchronization Errors from reflector to probe in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.7.1.14PerfCounter64read-onlycurrent
esaProbeStatsR2PLostPkts
OBJECT-TYPE
The number of Lost Pkts from reflector to probe in the current interval. For Y.1731 probes, these are the actual data frames lost.
1.3.6.1.4.1.2544.1.12.8.1.7.1.15PerfCounter64read-onlycurrent
esaProbeStatsLostPkts
OBJECT-TYPE
The total number of Lost Packets in the current interval. Packets which are not received from the reflector end beyond the configured timeout value are termed as lost. NOTE: This is not applicable for Y.1731 probes.
1.3.6.1.4.1.2544.1.12.8.1.7.1.16PerfCounter64read-onlycurrent
esaProbeStatsSeqGaps
OBJECT-TYPE
The total number of sequence gaps across all packets received in the current interval. If (Received Seq Number) is greater than or equal to (Last Received Seq Number + 2)) it is termed as a sequence gap. NOTE: This is not applicable for Y.1731 probes.
1.3.6.1.4.1.2544.1.12.8.1.7.1.17PerfCounter64read-onlycurrent
esaProbeStatsOutOfSeqErrs
OBJECT-TYPE
The total number of out of sequence errors across all packets received in the current interval. If (Received Seq Number) is less than or equal to (Last Received Seq Number), it is termed as out of sequence error. NOTE: This is not applicable for Y.1731 probes.
1.3.6.1.4.1.2544.1.12.8.1.7.1.18PerfCounter64read-onlycurrent
esaProbeStatsMinRoundTripDelay
OBJECT-TYPE
The minimum round-trip delay(in microseconds) across all packets received in the current interval. The reflector's processing time is excluded from the value.
1.3.6.1.4.1.2544.1.12.8.1.7.1.19Unsigned32read-onlycurrent
esaProbeStatsMaxRoundTripDelay
OBJECT-TYPE
The maximum round-trip delay(in microseconds) across all packets received in the current interval. The reflector's processing time is excluded from the value.
1.3.6.1.4.1.2544.1.12.8.1.7.1.20Unsigned32read-onlycurrent
esaProbeStatsAvgRoundTripDelay
OBJECT-TYPE
The average round-trip delay(in microseconds) across all packets received in the current interval. The reflector's processing time is excluded from the value.
1.3.6.1.4.1.2544.1.12.8.1.7.1.21Unsigned32read-onlycurrent
esaProbeStatsSumRoundTripDelay
OBJECT-TYPE
The total sum of round trip delay(in microseconds) in the current interval. The reflector's processing time is excluded from the value.
1.3.6.1.4.1.2544.1.12.8.1.7.1.22PerfCounter64read-onlycurrent
esaProbeStatsSumOfSqRoundTripDelay
OBJECT-TYPE
The sum of square of round trip delays in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.7.1.23PerfCounter64read-onlycurrent
esaProbeStatsMinOnewayP2RDelay
OBJECT-TYPE
The minimum one-way source to destination delay(in microseconds) across all packets received in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.7.1.24Unsigned32read-onlycurrent
esaProbeStatsMaxOnewayP2RDelay
OBJECT-TYPE
The maximum one-way source to destination delay(in microseconds) across all packets received in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.7.1.25Unsigned32read-onlycurrent
esaProbeStatsAvgOnewayP2RDelay
OBJECT-TYPE
The average one-way source to destination delay(in microseconds) across all packets received in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.7.1.26Unsigned32read-onlycurrent
esaProbeStatsSumOnewayP2RDelay
OBJECT-TYPE
The total sum of one-way delay from source to destination in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.7.1.27PerfCounter64read-onlycurrent
esaProbeStatsSumOfSqOnewayP2RDelay
OBJECT-TYPE
The sum of square of one-way delay from source to destination in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.7.1.28PerfCounter64read-onlycurrent
esaProbeStatsMinOnewayR2PDelay
OBJECT-TYPE
The minimum one-way destination to source delay(in microseconds) across all packets received in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.7.1.29Unsigned32read-onlycurrent
esaProbeStatsMaxOnewayR2PDelay
OBJECT-TYPE
The maximum one-way destination to source delay(in microseconds) across all packets received in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.7.1.30Unsigned32read-onlycurrent
esaProbeStatsAvgOnewayR2PDelay
OBJECT-TYPE
The average one-way destination to source delay(in microseconds) across all packets received in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.7.1.31Unsigned32read-onlycurrent
esaProbeStatsSumOnewayR2PDelay
OBJECT-TYPE
The total sum of one-way delay from destination to source in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.7.1.32PerfCounter64read-onlycurrent
esaProbeStatsSumOfSqOnewayR2PDelay
OBJECT-TYPE
The sum of square of one-way delay from destination to source in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.7.1.33PerfCounter64read-onlycurrent
esaProbeStatsMinPosP2RJitter
OBJECT-TYPE
The minimum positive one-way jitter from source to destination in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.7.1.34Unsigned32read-onlycurrent
esaProbeStatsMaxPosP2RJitter
OBJECT-TYPE
The maximum positive one-way jitter from source to destination in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.7.1.35Unsigned32read-onlycurrent
esaProbeStatsNumPosP2RJitter
OBJECT-TYPE
The total number of positive one-way jitters from source to destination in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.7.1.36PerfCounter64read-onlycurrent
esaProbeStatsSumPosP2RJitter
OBJECT-TYPE
The total sum of positive one-way jitters from source to destination in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.7.1.37PerfCounter64read-onlycurrent
esaProbeStatsSumOfSqPosP2RJitter
OBJECT-TYPE
The sum of square of positive one-way jitters from source to destination in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.7.1.38PerfCounter64read-onlycurrent
esaProbeStatsMinNegP2RJitter
OBJECT-TYPE
The minimum negative one-way jitter from source to destination in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.7.1.39Unsigned32read-onlycurrent
esaProbeStatsMaxNegP2RJitter
OBJECT-TYPE
The maximum negative one-way jitter from source to destination in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.7.1.40Unsigned32read-onlycurrent
esaProbeStatsNumNegP2RJitter
OBJECT-TYPE
The total number of negative one-way jitters from source to destination in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.7.1.41PerfCounter64read-onlycurrent
esaProbeStatsSumNegP2RJitter
OBJECT-TYPE
The total sum of negative one-way jitters from source to destination in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.7.1.42PerfCounter64read-onlycurrent
esaProbeStatsSumOfSqNegP2RJitter
OBJECT-TYPE
The sum of square of negative one-way jitters from source to destination in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.7.1.43PerfCounter64read-onlycurrent
esaProbeStatsMinPosR2PJitter
OBJECT-TYPE
The minimum positive one-way jitter from destination to source in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.7.1.44Unsigned32read-onlycurrent
esaProbeStatsMaxPosR2PJitter
OBJECT-TYPE
The maximum positive one-way jitter from destination to source in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.7.1.45Unsigned32read-onlycurrent
esaProbeStatsNumPosR2PJitter
OBJECT-TYPE
The total number of positive one-way jitters from destination to source in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.7.1.46PerfCounter64read-onlycurrent
esaProbeStatsSumPosR2PJitter
OBJECT-TYPE
The total sum of positive one-way jitters from destination to source in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.7.1.47PerfCounter64read-onlycurrent
esaProbeStatsSumOfSqPosR2PJitter
OBJECT-TYPE
The sum of square of positive one-way jitters from destination to source in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.7.1.48PerfCounter64read-onlycurrent
esaProbeStatsMinNegR2PJitter
OBJECT-TYPE
The minimum negative one-way jitter from destination to source in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.7.1.49Unsigned32read-onlycurrent
esaProbeStatsMaxNegR2PJitter
OBJECT-TYPE
The maximum negative one-way jitter from destination to source in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.7.1.50Unsigned32read-onlycurrent
esaProbeStatsNumNegR2PJitter
OBJECT-TYPE
The total number of negative one-way jitters from destination to source in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.7.1.51PerfCounter64read-onlycurrent
esaProbeStatsSumNegR2PJitter
OBJECT-TYPE
The total sum of negative one-way jitters from destination to source in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.7.1.52PerfCounter64read-onlycurrent
esaProbeStatsSumOfSqNegR2PJitter
OBJECT-TYPE
The sum of square of negative one-way jitters from destination to source in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.7.1.53PerfCounter64read-onlycurrent
esaProbeStatsY1731P2RNegLossOccurrences
OBJECT-TYPE
This attribute is only applicable to Y.1731 probes. This is the number of occurences of negative frame loss from Source MEP (Probe) to Destination MEP (Reflector). If these counts are non-zero then there could be some kind of provisioning mismatch between the Probe MEP and Reflector MEP. Here are some scenarios this can happen: - Probe MEP is configured to count in-profile frames only and the Reflector MEP is configured to count all frames with a mismatch in value for the attribute cfmMepLmCountInProfileFrames. - Probe MEP is configured to count data frames for specific VLAN priority and the Reflector MEP is configured to count data frames for all the priorities with a mismatch in values for the attributes cfmMepLmTxCountAllPrios or cfmMepLmRxCountAllPrios. NOTE: This could possibly happen due to reasons not related to configuration such as frame reordering in the network.
1.3.6.1.4.1.2544.1.12.8.1.7.1.54PerfCounter64read-onlycurrent
esaProbeStatsY1731R2PNegLossOccurrences
OBJECT-TYPE
This attribute is only applicable to Y.1731 probes. This is the number of occurences of negative frame loss from to Destination MEP (Reflector) to Source MEP (Probe). If these counts are non-zero then there could be some kind of provisioning mismatch between the Probe MEP and Reflector MEP. Here are some scenarios this can happen: - Probe MEP is configured to count in-profile frames only and the Reflector MEP is configured to count all frames with a mismatch in value for the attribute cfmMepLmCountInProfileFrames. - Probe MEP is configured to count data frames for specific VLAN priority and the Reflector MEP is configured to count data frames for all the priorities with a mismatch in values for the attributes cfmMepLmTxCountAllPrios or cfmMepLmRxCountAllPrios. NOTE: This could possibly happen due to reasons not related to configuration such as frame reordering in the network.
1.3.6.1.4.1.2544.1.12.8.1.7.1.55PerfCounter64read-onlycurrent
esaProbeStatsY1731RxLmSamples
OBJECT-TYPE
This attribute is only applicable to Y.1731 probes. This flag indicates that at least one loss measurement sample was received for this bin period (LMRs received). This is used by the user to differentiate between valid zero frame loss and not receiving any LMRs.
1.3.6.1.4.1.2544.1.12.8.1.7.1.56TruthValueread-onlycurrent
esaProbeStatsY1731RxDmSamples
OBJECT-TYPE
This attribute is only applicable to Y.1731 probes. This flag indicates that at least one delay measurement sample was received for this bin period (DMRs received).
1.3.6.1.4.1.2544.1.12.8.1.7.1.57TruthValueread-onlycurrent
esaProbeStatsY1731P2RFrames
OBJECT-TYPE
This attribute is only applicable to Y.1731 probes. This is the number of data frames counted by the Source MEP (Probe) that are transmitted towards the Destination MEP (Reflector). Based on the configuration the MEP counts the data frames with: - MEP's LM TX priority or all the priorities - All the VLAN IDs belonging the MEP's MA VID list.
1.3.6.1.4.1.2544.1.12.8.1.7.1.58PerfCounter64read-onlycurrent
esaProbeStatsY1731R2PFrames
OBJECT-TYPE
This attribute is only applicable to Y.1731 probes. This is the number of data frames counted by the Destination MEP (Reflector) that are transmitted towards the Source MEP (Probe). Based on the configuration the MEP counts the data frames with: - MEP's LM RX priority or all the priorities - All the VLAN IDs belonging the MEP's MA VID list.
1.3.6.1.4.1.2544.1.12.8.1.7.1.59PerfCounter64read-onlycurrent
esaProbeStatsAvgAbsP2RJitter
OBJECT-TYPE
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the average absolute P2R Jitter value. .
1.3.6.1.4.1.2544.1.12.8.1.7.1.60Unsigned32read-onlycurrent
esaProbeStatsAvgAbsR2PJitter
OBJECT-TYPE
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the average absolute R2P Jitter value. .
1.3.6.1.4.1.2544.1.12.8.1.7.1.61Unsigned32read-onlycurrent
esaProbeStatsMinAbsP2RJitter
OBJECT-TYPE
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the minimum absolute P2R Jitter value. .
1.3.6.1.4.1.2544.1.12.8.1.7.1.62Unsigned32read-onlycurrent
esaProbeStatsMinAbsR2PJitter
OBJECT-TYPE
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the minimum absolute R2P Jitter value. .
1.3.6.1.4.1.2544.1.12.8.1.7.1.63Unsigned32read-onlycurrent
esaProbeStatsMaxAbsP2RJitter
OBJECT-TYPE
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the maximum absolute P2R Jitter value. .
1.3.6.1.4.1.2544.1.12.8.1.7.1.64Unsigned32read-onlycurrent
esaProbeStatsMaxAbsR2PJitter
OBJECT-TYPE
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the maximum absolute R2P Jitter value. .
1.3.6.1.4.1.2544.1.12.8.1.7.1.65Unsigned32read-onlycurrent
esaProbeStatsNumAbsP2RJitter
OBJECT-TYPE
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the number of absolute P2R Jitters.
1.3.6.1.4.1.2544.1.12.8.1.7.1.66PerfCounter64read-onlycurrent
esaProbeStatsNumAbsR2PJitter
OBJECT-TYPE
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the number of absolute R2P Jitters.
1.3.6.1.4.1.2544.1.12.8.1.7.1.67PerfCounter64read-onlycurrent
esaProbeStatsSumAbsP2RJitter
OBJECT-TYPE
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the sum of absolute P2R Jitter values.
1.3.6.1.4.1.2544.1.12.8.1.7.1.68PerfCounter64read-onlycurrent
esaProbeStatsSumAbsR2PJitter
OBJECT-TYPE
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the sum of absolute R2P Jitter values.
1.3.6.1.4.1.2544.1.12.8.1.7.1.69PerfCounter64read-onlycurrent
esaProbeStatsSumOfSqAbsP2RJitter
OBJECT-TYPE
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the sum of squares of absolute P2R Jitter values.
1.3.6.1.4.1.2544.1.12.8.1.7.1.70PerfCounter64read-onlycurrent
esaProbeStatsSumOfSqAbsR2PJitter
OBJECT-TYPE
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the sum of squares of absolute R2P Jitter values.
1.3.6.1.4.1.2544.1.12.8.1.7.1.71PerfCounter64read-onlycurrent
esaProbeHistoryTable
OBJECT-TYPE
A collection of ESA Probe related history kept for a particular ESA Probe entity. These reflect the current data.
1.3.6.1.4.1.2544.1.12.8.1.8not-accessiblecurrent
esaProbeHistoryEntry
OBJECT-TYPE
A conceptual row in the esaProbeHistoryTable. An entry exists in this table for each ESA Probe.
1.3.6.1.4.1.2544.1.12.8.1.8.1not-accessiblecurrent
esaProbeHistoryDestinationIndex
OBJECT-TYPE
An integer index value used to uniquely identify a destination (Reflector) Index, in a point-to-multi point SLA. For Release 4.1 GE206, this value is 1, since only point-to-point SLA is supported.
1.3.6.1.4.1.2544.1.12.8.1.8.1.1Integer32read-onlycurrent
esaProbeHistoryCOSIndex
OBJECT-TYPE
An integer index value used to uniquely identify SLA for a specific Class of Service. For Release 4.1 GE206, this value is 1, since the COS is explicitly specified in the Probe parameters.
1.3.6.1.4.1.2544.1.12.8.1.8.1.2Integer32read-onlycurrent
esaProbeHistoryIndex
OBJECT-TYPE
An arbitrary integer index value used to uniquely identify this ESA Probe statistics history entry.
1.3.6.1.4.1.2544.1.12.8.1.8.1.3Integer32read-onlycurrent
esaProbeHistoryTime
OBJECT-TYPE
Indicates the time of history bin creation.
1.3.6.1.4.1.2544.1.12.8.1.8.1.4DateAndTimeread-onlycurrent
esaProbeHistoryValid
OBJECT-TYPE
Indicates the validity of the bin.
1.3.6.1.4.1.2544.1.12.8.1.8.1.5TruthValueread-onlycurrent
esaProbeHistoryAction
OBJECT-TYPE
Allows the Manager to clear the bin.
1.3.6.1.4.1.2544.1.12.8.1.8.1.6CmPmBinActionread-writecurrent
esaProbeHistoryCOS
OBJECT-TYPE
The Class of Service. For Release 4.1 GE206, this value is cos-not-applicable, since multi COS SLA is not supported.
1.3.6.1.4.1.2544.1.12.8.1.8.1.7ClassOfServiceTyperead-onlycurrent
esaProbeHistoryP2RPkts
OBJECT-TYPE
The total number of Transmitted Packets in the current interval. In the case of Y.1731 probes, this reflects the number of DMRs (Delay Measurement Replies) received and this will always be the same as the esaProbeHistoryR2PPkts.
1.3.6.1.4.1.2544.1.12.8.1.8.1.8PerfCounter64read-onlycurrent
esaProbeHistoryP2RErredPkts
OBJECT-TYPE
The total number of Packets in the current interval, for which there was a problem in transmission. This error is counted when there is a failure in packet transmission due to resource limitations (buffers). This can happen if the Probe Configuration was changed to send in a large number of packets in a time interval. NOTE: This is not applicable for Y.1731 probes.
1.3.6.1.4.1.2544.1.12.8.1.8.1.9PerfCounter64read-onlycurrent
esaProbeHistoryP2RSyncErrs
OBJECT-TYPE
The number of (time) Synchronization Errors from probe to reflector in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.8.1.10PerfCounter64read-onlycurrent
esaProbeHistoryP2RLostPkts
OBJECT-TYPE
The number of Lost Pkts from probe to reflector in the current interval. For Y.1731 probes, these are the actual data frames lost.
1.3.6.1.4.1.2544.1.12.8.1.8.1.11PerfCounter64read-onlycurrent
esaProbeHistoryR2PPkts
OBJECT-TYPE
The total number of Received Packets in the current interval. In the case of Y.1731 probes, this reflects the number of DMRs (Delay Measurement Replies) received and this will always be the same as the esaProbeHistoryP2RPkts.
1.3.6.1.4.1.2544.1.12.8.1.8.1.12PerfCounter64read-onlycurrent
esaProbeHistoryR2PErredPkts
OBJECT-TYPE
The total number of Received Packets in the current interval, which had errors such as length of received packet is less than the protocol header length, packet was received after it was marked as lost (i.e.beyond timeout). NOTE: This is not applicable for Y.1731 probes.
1.3.6.1.4.1.2544.1.12.8.1.8.1.13PerfCounter64read-onlycurrent
esaProbeHistoryR2PSyncErrs
OBJECT-TYPE
The number of (time) Synchronization Errors from reflector to probe in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.8.1.14PerfCounter64read-onlycurrent
esaProbeHistoryR2PLostPkts
OBJECT-TYPE
The number of Lost Pkts from reflector to probe in the current interval. For Y.1731 probes, these are the actual data frames lost.
1.3.6.1.4.1.2544.1.12.8.1.8.1.15PerfCounter64read-onlycurrent
esaProbeHistoryLostPkts
OBJECT-TYPE
The total number of Lost Packets in the current interval. Packets which are not received from the reflector end beyond the configured timeout value are termed as lost. NOTE: This is not applicable for Y.1731 probes.
1.3.6.1.4.1.2544.1.12.8.1.8.1.16PerfCounter64read-onlycurrent
esaProbeHistorySeqGaps
OBJECT-TYPE
The total number of sequence gaps across all packets received in the current interval. If (Received Seq Number) is greater than or equal to (Last Received Seq Number + 2)) it is termed as a sequence gap. NOTE: This is not applicable for Y.1731 probes.
1.3.6.1.4.1.2544.1.12.8.1.8.1.17PerfCounter64read-onlycurrent
esaProbeHistoryOutOfSeqErrs
OBJECT-TYPE
The total number of out of sequence errors across all packets received in the current interval. If (Received Seq Number) is less than or equal to (Last Received Seq Number), it is termed as out of sequence error. NOTE: This is not applicable for Y.1731 probes.
1.3.6.1.4.1.2544.1.12.8.1.8.1.18PerfCounter64read-onlycurrent
esaProbeHistoryMinRoundTripDelay
OBJECT-TYPE
The minimum round-trip delay(in microseconds) across all packets received in the current interval. The reflector's processing time is excluded from the value.
1.3.6.1.4.1.2544.1.12.8.1.8.1.19Unsigned32read-onlycurrent
esaProbeHistoryMaxRoundTripDelay
OBJECT-TYPE
The maximum round-trip delay(in microseconds) across all packets received in the current interval. The reflector's processing time is excluded from the value.
1.3.6.1.4.1.2544.1.12.8.1.8.1.20Unsigned32read-onlycurrent
esaProbeHistoryAvgRoundTripDelay
OBJECT-TYPE
The average round-trip delay(in microseconds) across all packets received in the current interval. The reflector's processing time is excluded from the value.
1.3.6.1.4.1.2544.1.12.8.1.8.1.21Unsigned32read-onlycurrent
esaProbeHistorySumRoundTripDelay
OBJECT-TYPE
The total sum of round trip delay(in microseconds) in the current interval. The reflector's processing time is excluded from the value.
1.3.6.1.4.1.2544.1.12.8.1.8.1.22PerfCounter64read-onlycurrent
esaProbeHistorySumOfSqRoundTripDelay
OBJECT-TYPE
The sum of square of round trip delays in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.8.1.23PerfCounter64read-onlycurrent
esaProbeHistoryMinOnewayP2RDelay
OBJECT-TYPE
The minimum one-way source to destination delay(in microseconds) across all packets received in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.8.1.24Unsigned32read-onlycurrent
esaProbeHistoryMaxOnewayP2RDelay
OBJECT-TYPE
The maximum one-way source to destination delay(in microseconds) across all packets received in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.8.1.25Unsigned32read-onlycurrent
esaProbeHistoryAvgOnewayP2RDelay
OBJECT-TYPE
The average one-way source to destination delay(in microseconds) across all packets received in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.8.1.26Unsigned32read-onlycurrent
esaProbeHistorySumOnewayP2RDelay
OBJECT-TYPE
The total sum of one-way delay from source to destination in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.8.1.27PerfCounter64read-onlycurrent
esaProbeHistorySumOfSqOnewayP2RDelay
OBJECT-TYPE
The sum of square of one-way delay from source to destination in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.8.1.28PerfCounter64read-onlycurrent
esaProbeHistoryMinOnewayR2PDelay
OBJECT-TYPE
The minimum one-way destination to source delay(in microseconds) across all packets received in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.8.1.29Unsigned32read-onlycurrent
esaProbeHistoryMaxOnewayR2PDelay
OBJECT-TYPE
The maximum one-way destination to source delay(in microseconds) across all packets received in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.8.1.30Unsigned32read-onlycurrent
esaProbeHistoryAvgOnewayR2PDelay
OBJECT-TYPE
The average one-way destination to source delay(in microseconds) across all packets received in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.8.1.31Unsigned32read-onlycurrent
esaProbeHistorySumOnewayR2PDelay
OBJECT-TYPE
The total sum of one-way delay from destination to source in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.8.1.32PerfCounter64read-onlycurrent
esaProbeHistorySumOfSqOnewayR2PDelay
OBJECT-TYPE
The sum of square of one-way delay from destination to source in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.8.1.33PerfCounter64read-onlycurrent
esaProbeHistoryMinPosP2RJitter
OBJECT-TYPE
The minimum positive one-way jitter from source to destination in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.8.1.34Unsigned32read-onlycurrent
esaProbeHistoryMaxPosP2RJitter
OBJECT-TYPE
The maximum positive one-way jitter from source to destination in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.8.1.35Unsigned32read-onlycurrent
esaProbeHistoryNumPosP2RJitter
OBJECT-TYPE
The total number of positive one-way jitters from source to destination in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.8.1.36PerfCounter64read-onlycurrent
esaProbeHistorySumPosP2RJitter
OBJECT-TYPE
The total sum of positive one-way jitters from source to destination in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.8.1.37PerfCounter64read-onlycurrent
esaProbeHistorySumOfSqPosP2RJitter
OBJECT-TYPE
The sum of square of positive one-way jitters from source to destination in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.8.1.38PerfCounter64read-onlycurrent
esaProbeHistoryMinNegP2RJitter
OBJECT-TYPE
The minimum negative one-way jitter from source to destination in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.8.1.39Unsigned32read-onlycurrent
esaProbeHistoryMaxNegP2RJitter
OBJECT-TYPE
The maximum negative one-way jitter from source to destination in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.8.1.40Unsigned32read-onlycurrent
esaProbeHistoryNumNegP2RJitter
OBJECT-TYPE
The total number of negative one-way jitters from source to destination in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.8.1.41PerfCounter64read-onlycurrent
esaProbeHistorySumNegP2RJitter
OBJECT-TYPE
The total sum of negative one-way jitters from source to destination in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.8.1.42PerfCounter64read-onlycurrent
esaProbeHistorySumOfSqNegP2RJitter
OBJECT-TYPE
The sum of square of negative one-way jitters from source to destination in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.8.1.43PerfCounter64read-onlycurrent
esaProbeHistoryMinPosR2PJitter
OBJECT-TYPE
The minimum positive one-way jitter from destination to source in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.8.1.44Unsigned32read-onlycurrent
esaProbeHistoryMaxPosR2PJitter
OBJECT-TYPE
The maximum positive one-way jitter from destination to source in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.8.1.45Unsigned32read-onlycurrent
esaProbeHistoryNumPosR2PJitter
OBJECT-TYPE
The total number of positive one-way jitters from destination to source in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.8.1.46PerfCounter64read-onlycurrent
esaProbeHistorySumPosR2PJitter
OBJECT-TYPE
The total sum of positive one-way jitters from destination to source in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.8.1.47PerfCounter64read-onlycurrent
esaProbeHistorySumOfSqPosR2PJitter
OBJECT-TYPE
The sum of square of positive one-way jitters from destination to source in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.8.1.48PerfCounter64read-onlycurrent
esaProbeHistoryMinNegR2PJitter
OBJECT-TYPE
The minimum negative one-way jitter from destination to source in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.8.1.49Unsigned32read-onlycurrent
esaProbeHistoryMaxNegR2PJitter
OBJECT-TYPE
The maximum negative one-way jitter from destination to source in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.8.1.50Unsigned32read-onlycurrent
esaProbeHistoryNumNegR2PJitter
OBJECT-TYPE
The total number of negative one-way jitters from destination to source in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.8.1.51PerfCounter64read-onlycurrent
esaProbeHistorySumNegR2PJitter
OBJECT-TYPE
The total sum of negative one-way jitters from destination to source in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.8.1.52PerfCounter64read-onlycurrent
esaProbeHistorySumOfSqNegR2PJitter
OBJECT-TYPE
The sum of square of negative one-way jitters from destination to source in the current interval.
1.3.6.1.4.1.2544.1.12.8.1.8.1.53PerfCounter64read-onlycurrent
esaProbeHistoryY1731P2RNegLossOccurrences
OBJECT-TYPE
This attribute is only applicable to Y.1731 probes. This is the number of occurences of negative frame loss from Source MEP (Probe) to Destination MEP (Reflector). If these counts are non-zero then there could be some kind of provisioning mismatch between the Probe MEP and Reflector MEP. Here are some scenarios this can happen: - Probe MEP is configured to count in-profile frames only and the Reflector MEP is configured to count all frames with a mismatch in value for the attribute cfmMepLmCountInProfileFrames. - Probe MEP is configured to count data frames for specific VLAN priority and the Reflector MEP is configured to count data frames for all the priorities with a mismatch in values for the attributes cfmMepLmTxCountAllPrios or cfmMepLmRxCountAllPrios. NOTE: This could possibly happen due to reasons not related to configuration such as frame reordering in the network.
1.3.6.1.4.1.2544.1.12.8.1.8.1.54PerfCounter64read-onlycurrent
esaProbeHistoryY1731R2PNegLossOccurrences
OBJECT-TYPE
This attribute is only applicable to Y.1731 probes. This is the number of occurences of negative frame loss from to Destination MEP (Reflector) to Source MEP (Probe). If these counts are non-zero then there could be some kind of provisioning mismatch between the Probe MEP and Reflector MEP. Here are some scenarios this can happen: - Probe MEP is configured to count in-profile frames only and the Reflector MEP is configured to count all frames with a mismatch in value for the attribute cfmMepLmCountInProfileFrames. - Probe MEP is configured to count data frames for specific VLAN priority and the Reflector MEP is configured to count data frames for all the priorities with a mismatch in values for the attributes cfmMepLmTxCountAllPrios or cfmMepLmRxCountAllPrios. NOTE: This could possibly happen due to reasons not related to configuration such as frame reordering in the network.
1.3.6.1.4.1.2544.1.12.8.1.8.1.55PerfCounter64read-onlycurrent
esaProbeHistoryY1731RxLmSamples
OBJECT-TYPE
This attribute is only applicable to Y.1731 probes. This flag indicates that at least one loss measurement sample was received for this bin period (LMRs received). This is used by the user to differentiate between valid zero frame loss and not receiving any LMRs.
1.3.6.1.4.1.2544.1.12.8.1.8.1.56TruthValueread-onlycurrent
esaProbeHistoryY1731RxDmSamples
OBJECT-TYPE
This attribute is only applicable to Y.1731 probes. This flag indicates that at least one delay measurement sample was received for this bin period (DMRs received).
1.3.6.1.4.1.2544.1.12.8.1.8.1.57TruthValueread-onlycurrent
esaProbeHistoryY1731P2RFrames
OBJECT-TYPE
This attribute is only applicable to Y.1731 probes. This is the number of data frames counted by the Source MEP (Probe) that are transmitted towards the Destination MEP (Reflector). Based on the configuration the MEP counts the data frames with: - MEP's LM TX priority or all the priorities - All the VLAN IDs belonging the MEP's MA VID list.
1.3.6.1.4.1.2544.1.12.8.1.8.1.58PerfCounter64read-onlycurrent
esaProbeHistoryY1731R2PFrames
OBJECT-TYPE
This attribute is only applicable to Y.1731 probes. This is the number of data frames counted by the Destination MEP (Reflector) that are transmitted towards the Source MEP (Probe). Based on the configuration the MEP counts the data frames with: - MEP's LM RX priority or all the priorities - All the VLAN IDs belonging the MEP's MA VID list.
1.3.6.1.4.1.2544.1.12.8.1.8.1.59PerfCounter64read-onlycurrent
esaProbeHistoryAvgAbsP2RJitter
OBJECT-TYPE
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the average absolute P2R Jitter value. .
1.3.6.1.4.1.2544.1.12.8.1.8.1.60Unsigned32read-onlycurrent
esaProbeHistoryAvgAbsR2PJitter
OBJECT-TYPE
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the average absolute R2P Jitter value. .
1.3.6.1.4.1.2544.1.12.8.1.8.1.61Unsigned32read-onlycurrent
esaProbeHistoryMinAbsP2RJitter
OBJECT-TYPE
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the minimum absolute P2R Jitter value. .
1.3.6.1.4.1.2544.1.12.8.1.8.1.62Unsigned32read-onlycurrent
esaProbeHistoryMinAbsR2PJitter
OBJECT-TYPE
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the minimum absolute R2P Jitter value. .
1.3.6.1.4.1.2544.1.12.8.1.8.1.63Unsigned32read-onlycurrent
esaProbeHistoryMaxAbsP2RJitter
OBJECT-TYPE
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the maximum absolute P2R Jitter value. .
1.3.6.1.4.1.2544.1.12.8.1.8.1.64Unsigned32read-onlycurrent
esaProbeHistoryMaxAbsR2PJitter
OBJECT-TYPE
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the maximum absolute R2P Jitter value. .
1.3.6.1.4.1.2544.1.12.8.1.8.1.65Unsigned32read-onlycurrent
esaProbeHistoryNumAbsP2RJitter
OBJECT-TYPE
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the number of absolute P2R Jitters.
1.3.6.1.4.1.2544.1.12.8.1.8.1.66PerfCounter64read-onlycurrent
esaProbeHistoryNumAbsR2PJitter
OBJECT-TYPE
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the number of absolute R2P Jitters.
1.3.6.1.4.1.2544.1.12.8.1.8.1.67PerfCounter64read-onlycurrent
esaProbeHistorySumAbsP2RJitter
OBJECT-TYPE
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the sum of absolute P2R Jitter values.
1.3.6.1.4.1.2544.1.12.8.1.8.1.68PerfCounter64read-onlycurrent
esaProbeHistorySumAbsR2PJitter
OBJECT-TYPE
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the sum of absolute R2P Jitter values.
1.3.6.1.4.1.2544.1.12.8.1.8.1.69PerfCounter64read-onlycurrent
esaProbeHistorySumOfSqAbsP2RJitter
OBJECT-TYPE
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the sum of squares of absolute P2R Jitter values.
1.3.6.1.4.1.2544.1.12.8.1.8.1.70PerfCounter64read-onlycurrent
esaProbeHistorySumOfSqAbsR2PJitter
OBJECT-TYPE
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the sum of squares of absolute R2P Jitter values.
1.3.6.1.4.1.2544.1.12.8.1.8.1.71PerfCounter64read-onlycurrent
esaProbeDistStatsConfigTable
OBJECT-TYPE
A list of entries that need to be configured in order to obtain statistical distribution of ESA Probe collected data.
1.3.6.1.4.1.2544.1.12.8.1.9not-accessiblecurrent
esaProbeDistStatsConfigEntry
OBJECT-TYPE
A row in the esaProbeDistStatsConfigTable.
1.3.6.1.4.1.2544.1.12.8.1.9.1not-accessiblecurrent
esaProbeDistStatsConfigIndex
OBJECT-TYPE
A unique index for each row. Each row corresponds to each enumeration type specified in EsaProbeDistStatsType.
1.3.6.1.4.1.2544.1.12.8.1.9.1.1Integer32 (1..11)read-onlycurrent
esaProbeDistStatsConfigType
OBJECT-TYPE
Indicates whether the statistical distribution is for round-trip delay (rt-delay), one-way probe to reflector delay (oneway-p2rdelay), one-way reflector to probe delay(oneway-r2pdelay), probe to reflector jitter (oneway-p2rjitter) or one-way reflector to probe jitter (oneway-r2pjitter).
1.3.6.1.4.1.2544.1.12.8.1.9.1.2EsaProbeDistStatsTyperead-onlycurrent
esaProbeDistStatsConfigMinVal
OBJECT-TYPE
Minimum sample value in distribution.
1.3.6.1.4.1.2544.1.12.8.1.9.1.3Integer32read-writecurrent
esaProbeDistStatsConfigMaxVal
OBJECT-TYPE
Maximum sample value in distribution.
1.3.6.1.4.1.2544.1.12.8.1.9.1.4Integer32read-writecurrent
esaProbeDistStatsConfigNumBins
OBJECT-TYPE
Number of distribution bins.
1.3.6.1.4.1.2544.1.12.8.1.9.1.5Unsigned32read-writecurrent
esaProbeDistStatsConfigLowBoundOfBin1
OBJECT-TYPE
The lower bound of the 1st bin.
1.3.6.1.4.1.2544.1.12.8.1.9.1.6Integer32read-writecurrent
esaProbeDistStatsConfigLowBoundOfBin2
OBJECT-TYPE
The lower bound of the 2nd bin.
1.3.6.1.4.1.2544.1.12.8.1.9.1.7Integer32read-writecurrent
esaProbeDistStatsConfigLowBoundOfBin3
OBJECT-TYPE
The lower bound of the 3rd bin.
1.3.6.1.4.1.2544.1.12.8.1.9.1.8Integer32read-writecurrent
esaProbeDistStatsConfigLowBoundOfBin4
OBJECT-TYPE
The lower bound of the 4th bin.
1.3.6.1.4.1.2544.1.12.8.1.9.1.9Integer32read-writecurrent
esaProbeDistStatsConfigLowBoundOfBin5
OBJECT-TYPE
The lower bound of the 5th bin.
1.3.6.1.4.1.2544.1.12.8.1.9.1.10Integer32read-writecurrent
esaProbeDistStatsConfigLowBoundOfBin6
OBJECT-TYPE
The lower bound of the 6th bin.
1.3.6.1.4.1.2544.1.12.8.1.9.1.11Integer32read-writecurrent
esaProbeDistStatsConfigLowBoundOfBin7
OBJECT-TYPE
The lower bound of the 7th bin.
1.3.6.1.4.1.2544.1.12.8.1.9.1.12Integer32read-writecurrent
esaProbeDistStatsConfigLowBoundOfBin8
OBJECT-TYPE
The lower bound of the 8th bin.
1.3.6.1.4.1.2544.1.12.8.1.9.1.13Integer32read-writecurrent
esaProbeDistStatsConfigLowBoundOfBin9
OBJECT-TYPE
The lower bound of the 9th bin.
1.3.6.1.4.1.2544.1.12.8.1.9.1.14Integer32read-writecurrent
esaProbeDistStatsTable
OBJECT-TYPE
A list of entries that provide statistical distribution of ESA Probe collected data.
1.3.6.1.4.1.2544.1.12.8.1.10not-accessiblecurrent
esaProbeDistStatsEntry
OBJECT-TYPE
A row in the esaProbeDistStatsTable.
1.3.6.1.4.1.2544.1.12.8.1.10.1not-accessiblecurrent
esaProbeDistStatsDestinationIndex
OBJECT-TYPE
An integer index value used to uniquely identify a destination (Reflector) Index, in a point-to-multi point SLA. For Release 4.1 GE206, this value is 1, since only point-to-point SLA is supported.
1.3.6.1.4.1.2544.1.12.8.1.10.1.1Integer32read-onlycurrent
esaProbeDistStatsCOSIndex
OBJECT-TYPE
An integer index value used to uniquely identify SLA for a specific Class of Service. For Release 4.1 GE206, this value is 1, since the COS is explicitly specified in the Probe parameters.
1.3.6.1.4.1.2544.1.12.8.1.10.1.2Integer32read-onlycurrent
esaProbeDistStatsAction
OBJECT-TYPE
Allows the Manager to clear the bin.
1.3.6.1.4.1.2544.1.12.8.1.10.1.3CmPmBinActionread-writecurrent
esaProbeDistStatsCOS
OBJECT-TYPE
The Class of Service. For Release 4.1 GE206, this value is cos-not-applicable, since multi COS SLA is not supported.
1.3.6.1.4.1.2544.1.12.8.1.10.1.4ClassOfServiceTyperead-onlycurrent
esaProbeDistStatsNumBins
OBJECT-TYPE
Number of bins over which the statistical data is distributed.
1.3.6.1.4.1.2544.1.12.8.1.10.1.5Integer32read-onlycurrent
esaProbeDistStatsLTMin
OBJECT-TYPE
Number of sample data points which are less than the minimum value specified.
1.3.6.1.4.1.2544.1.12.8.1.10.1.6PerfCounter64read-onlycurrent
esaProbeDistStatsGTMax
OBJECT-TYPE
Number of sample data points which are greater than the maximum value specified.
1.3.6.1.4.1.2544.1.12.8.1.10.1.7PerfCounter64read-onlycurrent
esaProbeDistStatsBinTable
OBJECT-TYPE
A list of entries that provide statistical distribution of ESA Probe collected data for specific BINs.
1.3.6.1.4.1.2544.1.12.8.1.11not-accessiblecurrent
esaProbeDistStatsBinEntry
OBJECT-TYPE
A row in the esaProbeDistStatsBinTable.
1.3.6.1.4.1.2544.1.12.8.1.11.1not-accessiblecurrent
esaProbeDistStatsBinIndex
OBJECT-TYPE
An index for each row that uniquely provides statistical data for a range.
1.3.6.1.4.1.2544.1.12.8.1.11.1.1Integer32 (1..65535)read-onlycurrent
esaProbeDistStatsBinLower
OBJECT-TYPE
The lower limit of values collected in this bin.
1.3.6.1.4.1.2544.1.12.8.1.11.1.2Integer32read-onlycurrent
esaProbeDistStatsBinUpper
OBJECT-TYPE
The upper limit of values collected in this bin.
1.3.6.1.4.1.2544.1.12.8.1.11.1.3Integer32read-onlycurrent
esaProbeDistStatsBinNumSamples
OBJECT-TYPE
Number of sample data points which fall between the lower and upper limits.
1.3.6.1.4.1.2544.1.12.8.1.11.1.4PerfCounter64read-onlycurrent
esaProbeDistHistoryTable
OBJECT-TYPE
A list of entries that provide statistical distribution history of ESA Probe collected data.
1.3.6.1.4.1.2544.1.12.8.1.12not-accessiblecurrent
esaProbeDistHistoryEntry
OBJECT-TYPE
A row in the esaProbeDistHistoryTable.
1.3.6.1.4.1.2544.1.12.8.1.12.1not-accessiblecurrent
esaProbeDistHistoryDestinationIndex
OBJECT-TYPE
An integer index value used to uniquely identify a destination (Reflector) Index, in a point-to-multi point SLA. For Release 4.1 GE206, this value is 1, since only point-to-point SLA is supported.
1.3.6.1.4.1.2544.1.12.8.1.12.1.1Integer32read-onlycurrent
esaProbeDistHistoryCOSIndex
OBJECT-TYPE
An integer index value used to uniquely identify SLA for a specific Class of Service. For Release 4.1 GE206, this value is 1, since the COS is explicitly specified in the Probe parameters.
1.3.6.1.4.1.2544.1.12.8.1.12.1.2Integer32read-onlycurrent
esaProbeDistHistoryIndex
OBJECT-TYPE
An arbitrary integer index value used to uniquely identify this ESA Probe Distribution History entry.
1.3.6.1.4.1.2544.1.12.8.1.12.1.3Integer32 (1..65535)read-onlycurrent
esaProbeDistHistoryTime
OBJECT-TYPE
Indicates the time of history bin creation.
1.3.6.1.4.1.2544.1.12.8.1.12.1.4DateAndTimeread-onlycurrent
esaProbeDistHistoryAction
OBJECT-TYPE
Allows the Manager to clear the bin.
1.3.6.1.4.1.2544.1.12.8.1.12.1.5CmPmBinActionread-writecurrent
esaProbeDistHistoryCOS
OBJECT-TYPE
The Class of Service. For Release 4.1 GE206, this value is cos-not-applicable, since multi COS SLA is not supported.
1.3.6.1.4.1.2544.1.12.8.1.12.1.6ClassOfServiceTyperead-onlycurrent
esaProbeDistHistoryNumBins
OBJECT-TYPE
Number of bins over which the statistical data is distributed.
1.3.6.1.4.1.2544.1.12.8.1.12.1.7Integer32read-onlycurrent
esaProbeDistHistoryLTMin
OBJECT-TYPE
Number of sample data points which are less than the minimum value specified.
1.3.6.1.4.1.2544.1.12.8.1.12.1.8PerfCounter64read-onlycurrent
esaProbeDistHistoryGTMax
OBJECT-TYPE
Number of sample data points which are greater than the maximum value specified.
1.3.6.1.4.1.2544.1.12.8.1.12.1.9PerfCounter64read-onlycurrent
esaProbeDistHistoryBinTable
OBJECT-TYPE
A list of entries that provide historical statistical distribution of ESA Probe collected data for specific BINs.
1.3.6.1.4.1.2544.1.12.8.1.13not-accessiblecurrent
esaProbeDistHistoryBinEntry
OBJECT-TYPE
A row in the esaProbeDistHistoryBinTable.
1.3.6.1.4.1.2544.1.12.8.1.13.1not-accessiblecurrent
esaProbeDistHistoryBinIndex
OBJECT-TYPE
An index for each row that uniquely provides statistical data for a range.
1.3.6.1.4.1.2544.1.12.8.1.13.1.1Integer32 (1..65535)read-onlycurrent
esaProbeDistHistoryBinLower
OBJECT-TYPE
The lower limit of values collected in this bin.
1.3.6.1.4.1.2544.1.12.8.1.13.1.2Integer32read-onlycurrent
esaProbeDistHistoryBinUpper
OBJECT-TYPE
The upper limit of values collected in this bin.
1.3.6.1.4.1.2544.1.12.8.1.13.1.3Integer32read-onlycurrent
esaProbeDistHistoryBinNumSamples
OBJECT-TYPE
Number of sample data points which fall between the lower and upper limits.
1.3.6.1.4.1.2544.1.12.8.1.13.1.4PerfCounter64read-onlycurrent
esaProbeStatsThresholdTable
OBJECT-TYPE
A table of entries that allow manageability of ESA Probe Thresholds.
1.3.6.1.4.1.2544.1.12.8.1.14not-accessiblecurrent
esaProbeStatsThresholdEntry
OBJECT-TYPE
A conceptual row in the esaProbeStatsThresholdTable.
1.3.6.1.4.1.2544.1.12.8.1.14.1not-accessiblecurrent
esaProbeStatsThresholdIndex
OBJECT-TYPE
An index that uniquely identifies an entry in the esaProbeStatsThresholdTable.
1.3.6.1.4.1.2544.1.12.8.1.14.1.1Integer32 (1..65535)read-onlycurrent
esaProbeStatsThresholdVariable
OBJECT-TYPE
The object identifier of the particular variable to be sampled. Objects of the esaProbeStatsTable table are monitored. Only variables that resolve to an ASN.1 primitive type of INTEGER (INTEGER, Integer32, Counter32, PerfCounter64, Gauge, or TimeTicks) may be sampled.
1.3.6.1.4.1.2544.1.12.8.1.14.1.2VariablePointerread-onlycurrent
esaProbeStatsThresholdAbsValueLo
OBJECT-TYPE
Lower 32 bits of the absolute value of the threshold.
1.3.6.1.4.1.2544.1.12.8.1.14.1.3Unsigned32read-writecurrent
esaProbeStatsThresholdAbsValueHi
OBJECT-TYPE
Higher 32 bits of the absolute value of the threshold.
1.3.6.1.4.1.2544.1.12.8.1.14.1.4Unsigned32read-writecurrent
esaProbeStatsThresholdMonValue
OBJECT-TYPE
Monitored value corresponding to esaProbeStatsThresholdVariable.
1.3.6.1.4.1.2544.1.12.8.1.14.1.5PerfCounter64read-onlycurrent
esaProbeCOSConfigTable
OBJECT-TYPE
A list of entries corresponding to ESA Probes COS Configuration Levels.
1.3.6.1.4.1.2544.1.12.8.1.15not-accessiblecurrent
esaProbeCOSConfigEntry
OBJECT-TYPE
A row in the esaProbeCOSConfigTable. Entries can be created in this table by management application action.
1.3.6.1.4.1.2544.1.12.8.1.15.1not-accessiblecurrent
esaProbeCOSConfigIndex
OBJECT-TYPE
An integer index value used to uniquely identify SLA (Service Level Agreement) for a specific Class of Service. Index 1 is associated with cos-0, index 2 with cos-1, index 3 with cos-2 and so on.
1.3.6.1.4.1.2544.1.12.8.1.15.1.1Integer32 (1..8)read-createcurrent
esaProbeCOSConfigType
OBJECT-TYPE
This is the Class of Service Type for Y.1731/SLM-SLR Probes, associated with the row.
1.3.6.1.4.1.2544.1.12.8.1.15.1.2ClassOfServiceTyperead-createcurrent
esaProbeCOSConfigInterval
OBJECT-TYPE
This is the Class of Service Y.1731/SLM-SLR packet interval type.
1.3.6.1.4.1.2544.1.12.8.1.15.1.3EsaProbePktIntervalTyperead-createcurrent
esaProbeCOSConfigPktSize
OBJECT-TYPE
This is the Class of Service Y.1731/SLM-SLR Packet Size. This object enables specification of the TLV size for Delay Measurement Measures(DMMs) as well as Synthetic Loss Measurement Frames (SLMs).
1.3.6.1.4.1.2544.1.12.8.1.15.1.4Integer32 (64..9612)read-createcurrent
esaProbeCOSConfigStorageType
OBJECT-TYPE
The type of storage configured for this entry.
1.3.6.1.4.1.2544.1.12.8.1.15.1.5StorageTyperead-createcurrent
esaProbeCOSConfigRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of esaProbeCOSConfigRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with esaProbeCOSConfigRowStatus value as createAndGo(4). Upon successful row creation, this variable has a value of active(1). The esaProbeCOSConfigRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.8.1.15.1.6RowStatusread-createcurrent
esaProbeCOSConfigslmInterval
OBJECT-TYPE
This allows specification of the interval between subsequent SLM packets.
1.3.6.1.4.1.2544.1.12.8.1.15.1.7EsaProbePktIntervalTyperead-createcurrent
esaProbeCOSConfigslmPktSize
OBJECT-TYPE
This allows specification of the SLM Packet Size.
1.3.6.1.4.1.2544.1.12.8.1.15.1.8Integer32read-createcurrent
esaProbeCOSConfigSoamPmExtAvailFlrThreshold
OBJECT-TYPE
Frame loss ratio threshold for Availability (m%).
1.3.6.1.4.1.2544.1.12.8.1.15.1.9Unsigned32 (0..100000)read-writecurrent
esaProbeCOSConfigSoamPmExtFlrDeltaTNumLmPdus
OBJECT-TYPE
This is the number of loss measurement PDUs. delta_t is this attribute multiplied by the loss measurement message period. For example, if SLM message period is 100ms and this attribute is 10, then the delta_t is 1second.
1.3.6.1.4.1.2544.1.12.8.1.15.1.10Unsigned32 (1..1000000)read-writecurrent
esaProbeCOSConfigSoamPmExtConDeltaTsForAvail
OBJECT-TYPE
This is the number of consecutive delta_ts used in the computation of availability/unavailability (n).
1.3.6.1.4.1.2544.1.12.8.1.15.1.11Unsigned32 (1..1000)read-writecurrent
esaProbeMultiDestinationTable
OBJECT-TYPE
A list of entries corresponding to ESA Probes Multi Destinations.
1.3.6.1.4.1.2544.1.12.8.1.16not-accessiblecurrent
esaProbeMultiDestinationEntry
OBJECT-TYPE
A row in the esaProbeMultiDestinationTable. Entries can be created in this table by management application action. Entries in this table represent destinations in a point-to-multipoint ESA Probe.
1.3.6.1.4.1.2544.1.12.8.1.16.1not-accessiblecurrent
esaProbeDestinationIndex
OBJECT-TYPE
An integer index value used to uniquely identify a destination.
1.3.6.1.4.1.2544.1.12.8.1.16.1.1Integer32read-createcurrent
esaProbeDestinationMepType
OBJECT-TYPE
This attribute is applicable only for point-to-multipoint probes. This indicates if the destination MEP is specified using the MEP ID object esaProbeDestinationMepId.
1.3.6.1.4.1.2544.1.12.8.1.16.1.2MepDestinationTyperead-createcurrent
esaProbeDestinationMepMacAddr
OBJECT-TYPE
This attribute is applicable only for point-to-multipoint probes. It identifies the destination MEP. This MAC address will be the destination MAC address for frames if esaProbeDestinationMepType is 'macaddress'. If CC protocol is not enabled between source and destination MEP then this is the only choice to identify the remote MEP.
1.3.6.1.4.1.2544.1.12.8.1.16.1.3MacAddressread-createcurrent
esaProbeDestinationMepId
OBJECT-TYPE
This attribute is applicable only for point-to-multipoint probes. It identifies the destination MEP. The MAC address of this RMEP ID from RMEP database will be the destination MAC address. This value is used only if the esaProbeDestinationMepType is 'mepid'. CC protocol must be enabled between source and destination MEP if the RMEP ID is used to identify the Remote MEP.
1.3.6.1.4.1.2544.1.12.8.1.16.1.4Dot1agCfmMepIdOrZeroread-createcurrent
esaProbeDestinationStorageType
OBJECT-TYPE
The type of storage configured for this entry.
1.3.6.1.4.1.2544.1.12.8.1.16.1.5StorageTyperead-createcurrent
esaProbeDestinationRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of esaProbeDestinationRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with esaProbeDestinationRowStatus value as createAndGo(4). Upon successful row creation, this variable has a value of active(1). The esaProbeDestinationRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.8.1.16.1.6RowStatusread-createcurrent
bertControlTable
OBJECT-TYPE
A list of entries for the control of BERT Streams.
1.3.6.1.4.1.2544.1.12.8.1.17not-accessiblecurrent
bertControlEntry
OBJECT-TYPE
A conceptual row in the bertControlTable.
1.3.6.1.4.1.2544.1.12.8.1.17.1not-accessiblecurrent
bertControlIndex
OBJECT-TYPE
An arbitrary integer index value used to uniquely identify this BERT Control.
1.3.6.1.4.1.2544.1.12.8.1.17.1.1Integer32not-accessiblecurrent
bertControlSourceEntity
OBJECT-TYPE
Pointer to the entity on which the BERT will be started within a card.
1.3.6.1.4.1.2544.1.12.8.1.17.1.2VariablePointerread-writecurrent
bertControlTestMode
OBJECT-TYPE
The mode of BERT to be performed.
1.3.6.1.4.1.2544.1.12.8.1.17.1.3BerTestModeread-writecurrent
bertControlDuration
OBJECT-TYPE
This object enables specification of the time in seconds for BERT. BERT will be stopped after the specified time interval is exhausted.
1.3.6.1.4.1.2544.1.12.8.1.17.1.4Integer32 (0..259200)read-writecurrent
bertControlStream
OBJECT-TYPE
This object specifies which stream should be included in the BERT execution. Value of 0 indicates that no streams is selected by bertControlStream. Non 0 value indicates the selected BERT stream.
1.3.6.1.4.1.2544.1.12.8.1.17.1.5Integer32read-writecurrent
bertControlAction
OBJECT-TYPE
This object enables starting/stopping of traffic generation as well as resetting of monitored streams. This object may not be specified at configuration creation time - in this case it will take the value of `none'. This allows manager to explicitly control the start and stop of traffic generation/monitoring activity. Value of `stop' is invalid if the activity is specified but not started. Value of `start' is valid during creation time, as well as when activity is already stopped. Specification of `reset' resets the specified streams to default values, as well as clears the control specification. Get on this variable gives the most recent SNMP set specification.
1.3.6.1.4.1.2544.1.12.8.1.17.1.6BertControlActionread-writecurrent
bertControlTestStatus
OBJECT-TYPE
This object reflects the current status of test set configuration entry. Upon creation, the status has a value of `initial'; the status changes to `in-progress' upon ecpaControlAction indicating `start'; the status changes to `completed' upon ecpaControlAction indicating stop, as well as when the specified test generation completes autonomously upon completion of number of frames or completion of specified time interval.
1.3.6.1.4.1.2544.1.12.8.1.17.1.7BerTestStatusread-onlycurrent
bertConfigStreamTable
OBJECT-TYPE
A list of entries for the configuration of BERT Config Stream Specifications.
1.3.6.1.4.1.2544.1.12.8.1.18not-accessiblecurrent
bertConfigStreamEntry
OBJECT-TYPE
A conceptual row in the bertConfigStreamTable.
1.3.6.1.4.1.2544.1.12.8.1.18.1not-accessiblecurrent
bertConfigStreamIndex
OBJECT-TYPE
An arbitrary integer index value used to uniquely identify this BERT configStream.
1.3.6.1.4.1.2544.1.12.8.1.18.1.1Integer32not-accessiblecurrent
bertConfigStreamName
OBJECT-TYPE
Symbolic Stream Name that can be associated with an BERT Config stream.
1.3.6.1.4.1.2544.1.12.8.1.18.1.2DisplayString (SIZE(0..64))read-writecurrent
bertConfigStreamTxPattern
OBJECT-TYPE
Allows specification of the Tx pattern of this BERT Config stream.
1.3.6.1.4.1.2544.1.12.8.1.18.1.3BertPatternread-writecurrent
bertConfigStreamErrInjectEnabled
OBJECT-TYPE
This object allows specification of whether Bit Error be injected.
1.3.6.1.4.1.2544.1.12.8.1.18.1.4TruthValueread-writecurrent
bertConfigStreamErrInjectRate
OBJECT-TYPE
Bit Error Rate, applicable when Error Injection is enabled.
1.3.6.1.4.1.2544.1.12.8.1.18.1.5BitErrRateread-writecurrent
bertConfigStreamErrInjectRateMultiplier
OBJECT-TYPE
BER value with 0.1 Step, in this release is fixed 10, only applicable when Error Injection is enabled.
1.3.6.1.4.1.2544.1.12.8.1.18.1.6Integer32read-writecurrent
bertConfigStreamUserPatternLength
OBJECT-TYPE
User defined testing pattern length.
1.3.6.1.4.1.2544.1.12.8.1.18.1.7BertUserPatternLengthread-writecurrent
bertConfigStreamUserPattern
OBJECT-TYPE
User defined testing pattern in a HEX format display string, applicable when test pattern is user defined.
1.3.6.1.4.1.2544.1.12.8.1.18.1.8DisplayStringread-writecurrent
bertTestStreamTable
OBJECT-TYPE
A list of entries containing results of a previous test.
1.3.6.1.4.1.2544.1.12.8.1.19not-accessiblecurrent
bertTestStreamEntry
OBJECT-TYPE
A conceptual row in the bertTestStreamTable. Entries in this table show results of the current BERT.
1.3.6.1.4.1.2544.1.12.8.1.19.1not-accessiblecurrent
bertTestStreamIndex
OBJECT-TYPE
An integer index value corresponding to the stream index for which the BERT was initiated.
1.3.6.1.4.1.2544.1.12.8.1.19.1.1Integer32not-accessiblecurrent
bertTestStreamName
OBJECT-TYPE
Symbolic Stream Name that can be associated with an BERT stream.
1.3.6.1.4.1.2544.1.12.8.1.19.1.2DisplayString (SIZE(0..64))read-writecurrent
bertTestStreamTxPattern
OBJECT-TYPE
Allows specification of the Tx pattern of this BERT Test stream.
1.3.6.1.4.1.2544.1.12.8.1.19.1.3BertPatternread-onlycurrent
bertTestStreamErrInjectEnabled
OBJECT-TYPE
This object allows specification of whether Bit Error be injected.
1.3.6.1.4.1.2544.1.12.8.1.19.1.4TruthValueread-onlycurrent
bertTestStreamErrInjectRate
OBJECT-TYPE
Bit Error Rate, applicable when Error Injection is enabled.
1.3.6.1.4.1.2544.1.12.8.1.19.1.5BitErrRateread-onlycurrent
bertTestStreamErrInjectRateMultiplier
OBJECT-TYPE
BER value with 0.1 Step, in this release is fixed 10, only applicable when Error Injection is enabled.
1.3.6.1.4.1.2544.1.12.8.1.19.1.6Integer32read-onlycurrent
bertTestStreamUserPatternLength
OBJECT-TYPE
User defined testing pattern length.
1.3.6.1.4.1.2544.1.12.8.1.19.1.7BertUserPatternLengthread-onlycurrent
bertTestStreamUserPattern
OBJECT-TYPE
User defined testing pattern in a HEX format display string, applicable when test pattern is user defined.
1.3.6.1.4.1.2544.1.12.8.1.19.1.8DisplayStringread-onlycurrent
bertTestStreamMonStartTime
OBJECT-TYPE
The start time of the BERT for this stream.
1.3.6.1.4.1.2544.1.12.8.1.19.1.9DateAndTimeread-onlycurrent
bertTestStreamMonEndTime
OBJECT-TYPE
The end time of the BERT for this stream.
1.3.6.1.4.1.2544.1.12.8.1.19.1.10DateAndTimeread-onlycurrent
bertTestStreamMonElapsedTime
OBJECT-TYPE
The elapsed time of BERT for this stream in seconds.
1.3.6.1.4.1.2544.1.12.8.1.19.1.11Integer32read-onlycurrent
bertTestStreamMonSyncState
OBJECT-TYPE
The Sync State of the BERT.
1.3.6.1.4.1.2544.1.12.8.1.19.1.12BertSyncStateread-onlycurrent
bertTestStreamMonRxPattern
OBJECT-TYPE
Allows specification of the Rx pattern of this BERT Test stream.
1.3.6.1.4.1.2544.1.12.8.1.19.1.13BertPatternread-onlycurrent
bertTestStreamMonSyncCounts
OBJECT-TYPE
Allows specification of the Sync counts from test start.
1.3.6.1.4.1.2544.1.12.8.1.19.1.14Unsigned32read-onlycurrent
bertTestStreamMonRxBitErrsSinceStart
OBJECT-TYPE
Allows specification of the Received Errors since test start.
1.3.6.1.4.1.2544.1.12.8.1.19.1.15PerfCounter64read-onlycurrent
bertTestStreamMonRxBitsSinceStart
OBJECT-TYPE
Allows specification of the Received Bits since test start.
1.3.6.1.4.1.2544.1.12.8.1.19.1.16PerfCounter64read-onlycurrent
bertTestStreamMonRxESsSinceStart
OBJECT-TYPE
Allows specification of the Error seconds since test start.
1.3.6.1.4.1.2544.1.12.8.1.19.1.17Unsigned32read-onlycurrent
bertTestStreamMonRxErrRateSinceStart
OBJECT-TYPE
Allows specification of the Received BER Unit since test start.
1.3.6.1.4.1.2544.1.12.8.1.19.1.18BitErrRateread-onlycurrent
bertTestStreamMonRxErrRateMultiplierSinceStart
OBJECT-TYPE
Allows specification of the Received BER value with 0.1 Step since test start.
1.3.6.1.4.1.2544.1.12.8.1.19.1.19Integer32read-onlycurrent
bertTestStreamMonRxBitErrsSinceLastSync
OBJECT-TYPE
Allows specification of the Received Errors since last sync.
1.3.6.1.4.1.2544.1.12.8.1.19.1.20PerfCounter64read-onlycurrent
bertTestStreamMonRxBitsSinceLastSync
OBJECT-TYPE
Allows specification of the Received Bits since last sync.
1.3.6.1.4.1.2544.1.12.8.1.19.1.21PerfCounter64read-onlycurrent
bertTestStreamMonRxESsSinceLastSync
OBJECT-TYPE
Allows specification of the Received Error seconds since last sync.
1.3.6.1.4.1.2544.1.12.8.1.19.1.22Unsigned32read-onlycurrent
bertTestStreamMonRxErrRateSinceLastSync
OBJECT-TYPE
Allows specification of the Received BER Unit since last sync.
1.3.6.1.4.1.2544.1.12.8.1.19.1.23BitErrRateread-onlycurrent
bertTestStreamMonRxErrRateMultiplierSinceLastSync
OBJECT-TYPE
Allows specification of the Received BER value with 0.1 Step since last sync.
1.3.6.1.4.1.2544.1.12.8.1.19.1.24Unsigned32read-onlycurrent
bertTestStreamConfigChangedFlag
OBJECT-TYPE
This object provides information on whether the associated bertConfigStream is changed.
1.3.6.1.4.1.2544.1.12.8.1.19.1.25TruthValueread-onlycurrent
bertTestStreamMonOOSSsSinceStart
OBJECT-TYPE
This object means the Out of Sync Seconds since start.
1.3.6.1.4.1.2544.1.12.8.1.19.1.26Unsigned32read-onlycurrent
f3EsaProbeCOSConfigSoamPmExtTable
OBJECT-TYPE
A list of entries corresponding to ESA Probe Cos Configurations MEF 35.
1.3.6.1.4.1.2544.1.12.8.1.20not-accessiblecurrent
f3EsaProbeCOSConfigSoamPmExtEntry
OBJECT-TYPE
A row in the esaProbeCOSConfigTable MEF 35. Entries can be created in this table by management application action.
1.3.6.1.4.1.2544.1.12.8.1.20.1not-accessiblecurrent
f3EsaProbeCOSConfigSoamPmExtAvailFlrThreshold
OBJECT-TYPE
Frame loss ratio threshold for Availability (m%).
1.3.6.1.4.1.2544.1.12.8.1.20.1.1Unsigned32 (0..100000)read-writecurrent
f3EsaProbeCOSConfigSoamPmExtFlrDeltaTNumLmPdus
OBJECT-TYPE
This is the number of loss measurement PDUs. delta_t is this attribute multiplied by the loss measurement message period. For example, if SLM message period is 100ms and this attribute is 10, then the delta_t is 1second.
1.3.6.1.4.1.2544.1.12.8.1.20.1.2Unsigned32 (1..1000000)read-writecurrent
f3EsaProbeCOSConfigSoamPmExtConDeltaTsForAvail
OBJECT-TYPE
This is the number of consecutive delta_ts used in the computation of availability/unavailability (n).
1.3.6.1.4.1.2544.1.12.8.1.20.1.3Unsigned32 (1..1000)read-writecurrent
f3EsaProbeStatsSoamPmExtTable
OBJECT-TYPE
A collection of ESA Probe MEF 35 related statistics kept for a particular ESA Probe entity. These reflect the current data.
1.3.6.1.4.1.2544.1.12.8.1.21not-accessiblecurrent
f3EsaProbeStatsSoamPmExtEntry
OBJECT-TYPE
A conceptual row in the f3EsaProbeStatsSoamPmExtTable.
1.3.6.1.4.1.2544.1.12.8.1.21.1not-accessiblecurrent
f3EsaProbeStatsSoamPmExtMinP2RFlr
OBJECT-TYPE
This is the minimum probe to reflector FLR (m%).
1.3.6.1.4.1.2544.1.12.8.1.21.1.1PerfCounter64read-onlycurrent
f3EsaProbeStatsSoamPmExtMaxP2RFlr
OBJECT-TYPE
This is the maximum probe to reflector FLR (m%).
1.3.6.1.4.1.2544.1.12.8.1.21.1.2PerfCounter64read-onlycurrent
f3EsaProbeStatsSoamPmExtAvgP2RFlr
OBJECT-TYPE
This is the average probe to reflector FLR (m%).
1.3.6.1.4.1.2544.1.12.8.1.21.1.3PerfCounter64read-onlycurrent
f3EsaProbeStatsSoamPmExtMinR2PFlr
OBJECT-TYPE
This is the minimum reflector to probe FLR (m%).
1.3.6.1.4.1.2544.1.12.8.1.21.1.4PerfCounter64read-onlycurrent
f3EsaProbeStatsSoamPmExtMaxR2PFlr
OBJECT-TYPE
This is the maximum reflector to probe FLR (m%).
1.3.6.1.4.1.2544.1.12.8.1.21.1.5PerfCounter64read-onlycurrent
f3EsaProbeStatsSoamPmExtAvgR2PFlr
OBJECT-TYPE
This is the average reflector to probe FLR (m%).
1.3.6.1.4.1.2544.1.12.8.1.21.1.6PerfCounter64read-onlycurrent
f3EsaProbeStatsSoamPmExtP2rSeverelyErroredDeltaTs
OBJECT-TYPE
This is the number of delta_ts in which the FLR is greater than availability threshold in the probe to reflector direction.
1.3.6.1.4.1.2544.1.12.8.1.21.1.7PerfCounter64read-onlycurrent
f3EsaProbeStatsSoamPmExtR2PSeverelyErroredDeltaTs
OBJECT-TYPE
This is the number of delta_ts in which the FLR is greater than availability threshold in the reflector to probe direction.
1.3.6.1.4.1.2544.1.12.8.1.21.1.8PerfCounter64read-onlycurrent
f3EsaProbeStatsSoamPmExtP2rAvailableTime
OBJECT-TYPE
This is the probe to reflector available delta_ts which begins to increment when FLR is less than or equal to availability threshold for 'n' consecutive delta_ts. It is incremented until FLR is greater than availability threshold for 'n' consecutive delta_ts.
1.3.6.1.4.1.2544.1.12.8.1.21.1.9PerfCounter64read-onlycurrent
f3EsaProbeStatsSoamPmExtR2PAvailableTime
OBJECT-TYPE
This is the reflector to probe available delta_ts which begins to increment when FLR is less than or equal to availability threshold for 'n' consecutive delta_ts. It is incremented until FLR is greater than availability threshold for 'n' consecutive delta_ts.
1.3.6.1.4.1.2544.1.12.8.1.21.1.10PerfCounter64read-onlycurrent
f3EsaProbeStatsSoamPmExtP2rUnavailableTime
OBJECT-TYPE
This is the probe to reflector unavailable delta_ts which begins to increment when FLR is greater than availability threshold for 'n' consecutive delta_ts. It is incremented until FLR is less than or equal to availability threshold for 'n' consecutive delta_ts.
1.3.6.1.4.1.2544.1.12.8.1.21.1.11PerfCounter64read-onlycurrent
f3EsaProbeStatsSoamPmExtR2PUnavailableTime
OBJECT-TYPE
This is the reflector to probe unavailable delta_ts which begins to increment when FLR is greater than availability threshold for 'n' consecutive delta_ts. It is incremented until FLR is less than or equal to availability threshold for 'n' consecutive delta_ts.
1.3.6.1.4.1.2544.1.12.8.1.21.1.12PerfCounter64read-onlycurrent
f3EsaProbeStatsSoamPmExtMinAbsRTJitter
OBJECT-TYPE
Minimum absolute round-trip (two-way) jitter in a measurement interval (microseconds).
1.3.6.1.4.1.2544.1.12.8.1.21.1.13PerfCounter64read-onlycurrent
f3EsaProbeStatsSoamPmExtMaxAbsRTJitter
OBJECT-TYPE
Maximum absolute round-trip (two-way) jitter in a measurement interval (microseconds).
1.3.6.1.4.1.2544.1.12.8.1.21.1.14PerfCounter64read-onlycurrent
f3EsaProbeStatsSoamPmExtAvgAbsRTJitter
OBJECT-TYPE
Average absolute round-trip (two-way) jitter in a measurement interval (microseconds).
1.3.6.1.4.1.2544.1.12.8.1.21.1.15PerfCounter64read-onlycurrent
f3EsaProbeStatsSoamPmExtNumAbsRTJitter
OBJECT-TYPE
Number of absolute round-trip (two-way) jitter samples (microseconds).
1.3.6.1.4.1.2544.1.12.8.1.21.1.16PerfCounter64read-onlycurrent
f3EsaProbeStatsSoamPmExtSumAbsRTJitter
OBJECT-TYPE
Sum of absolute round-trip (two-way) jitter samples (microseconds).
1.3.6.1.4.1.2544.1.12.8.1.21.1.17PerfCounter64read-onlycurrent
f3EsaProbeStatsSoamPmExtSumOfSqAbsRTJitter
OBJECT-TYPE
Sum of squares of absolute round-trip (two-way) jitter samples (microseconds^2).
1.3.6.1.4.1.2544.1.12.8.1.21.1.18PerfCounter64read-onlycurrent
f3EsaProbeStatsSoamPmExtMaxP2RFDR
OBJECT-TYPE
Maximum P2R (Forward) FDR in a measurement interval (microseconds).
1.3.6.1.4.1.2544.1.12.8.1.21.1.19PerfCounter64read-onlycurrent
f3EsaProbeStatsSoamPmExtAvgP2RFDR
OBJECT-TYPE
Average P2R (Forward) FDR in a measurement interval (microseconds).
1.3.6.1.4.1.2544.1.12.8.1.21.1.20PerfCounter64read-onlycurrent
f3EsaProbeStatsSoamPmExtNumP2RFDR
OBJECT-TYPE
Number of P2R (Forward) FDR samples (microseconds).
1.3.6.1.4.1.2544.1.12.8.1.21.1.21PerfCounter64read-onlycurrent
f3EsaProbeStatsSoamPmExtSumP2RFDR
OBJECT-TYPE
Sum of P2R (Forward) FDR samples (microseconds).
1.3.6.1.4.1.2544.1.12.8.1.21.1.22PerfCounter64read-onlycurrent
f3EsaProbeStatsSoamPmExtSumOfSqP2RFDR
OBJECT-TYPE
Sum of squares of P2R (Forward) FDR samples (microseconds^2).
1.3.6.1.4.1.2544.1.12.8.1.21.1.23PerfCounter64read-onlycurrent
f3EsaProbeStatsSoamPmExtMaxR2PFDR
OBJECT-TYPE
Maximum R2P (Backward) FDR in a measurement interval (microseconds).
1.3.6.1.4.1.2544.1.12.8.1.21.1.24PerfCounter64read-onlycurrent
f3EsaProbeStatsSoamPmExtAvgR2PFDR
OBJECT-TYPE
Average R2P (Backward) FDR in a measurement interval (microseconds).
1.3.6.1.4.1.2544.1.12.8.1.21.1.25PerfCounter64read-onlycurrent
f3EsaProbeStatsSoamPmExtNumR2PFDR
OBJECT-TYPE
Number of R2P (Backward) FDR samples (microseconds).
1.3.6.1.4.1.2544.1.12.8.1.21.1.26PerfCounter64read-onlycurrent
f3EsaProbeStatsSoamPmExtSumR2PFDR
OBJECT-TYPE
Sum of R2P (Backward) FDR samples (microseconds).
1.3.6.1.4.1.2544.1.12.8.1.21.1.27PerfCounter64read-onlycurrent
f3EsaProbeStatsSoamPmExtSumOfSqR2PFDR
OBJECT-TYPE
Sum of squares of R2P (Backward) FDR samples (microseconds^2).
1.3.6.1.4.1.2544.1.12.8.1.21.1.28PerfCounter64read-onlycurrent
f3EsaProbeStatsSoamPmExtMaxRTFDR
OBJECT-TYPE
Maximum round-trip (two-way) FDR in a measurement interval (microseconds).
1.3.6.1.4.1.2544.1.12.8.1.21.1.29PerfCounter64read-onlycurrent
f3EsaProbeStatsSoamPmExtAvgRTFDR
OBJECT-TYPE
Average round-trip (two-way) FDR in a measurement interval (microseconds).
1.3.6.1.4.1.2544.1.12.8.1.21.1.30PerfCounter64read-onlycurrent
f3EsaProbeStatsSoamPmExtNumRTFDR
OBJECT-TYPE
Number of round-trip (two-way) FDR samples (microseconds).
1.3.6.1.4.1.2544.1.12.8.1.21.1.31PerfCounter64read-onlycurrent
f3EsaProbeStatsSoamPmExtSumRTFDR
OBJECT-TYPE
Sum of round-trip (two-way) FDR samples (microseconds).
1.3.6.1.4.1.2544.1.12.8.1.21.1.32PerfCounter64read-onlycurrent
f3EsaProbeStatsSoamPmExtSumOfSqRTFDR
OBJECT-TYPE
Sum of squares of round-trip (two-way) FDR samples (microseconds^2).
1.3.6.1.4.1.2544.1.12.8.1.21.1.33PerfCounter64read-onlycurrent
f3EsaProbeStatsSoamPmExtP2rAvailableDeltaTs
OBJECT-TYPE
Probe to reflector available delta_ts which begins to increment when FLR is less than or equal to availability threshold for 'n' consecutive delta_ts.
1.3.6.1.4.1.2544.1.12.8.1.21.1.34PerfCounter64read-onlycurrent
f3EsaProbeStatsSoamPmExtR2pAvailableDeltaTs
OBJECT-TYPE
Reflector to probe available delta_ts which begins to increment when FLR is less than or equal to availability threshold for 'n' consecutive delta_ts.
1.3.6.1.4.1.2544.1.12.8.1.21.1.35PerfCounter64read-onlycurrent
f3EsaProbeStatsSoamPmExtP2rUnavailableDeltaTs
OBJECT-TYPE
Probe to reflector unavailable delta_ts which begins to increment when FLR is greater than availability threshold for 'n' consecutive delta_ts.
1.3.6.1.4.1.2544.1.12.8.1.21.1.36PerfCounter64read-onlycurrent
f3EsaProbeStatsSoamPmExtR2pUnavailableDeltaTs
OBJECT-TYPE
Reflector to probe unavailable delta_ts which begins to increment when FLR is greater than availability threshold for 'n' consecutive delta_ts.
1.3.6.1.4.1.2544.1.12.8.1.21.1.37PerfCounter64read-onlycurrent
f3EsaProbeStatsSoamPmExtElapsedTime
OBJECT-TYPE
The elapsed time (monotonic time) for the interval which could be less or more than measurement interval based on which the Time of Day was moved forward or backwards respectively (miliseconds).
1.3.6.1.4.1.2544.1.12.8.1.21.1.38PerfCounter64read-onlycurrent
f3EsaProbeHistorySoamPmExtTable
OBJECT-TYPE
A collection of ESA Probe MEF 35 related history kept for a particular ESA Probe entity. These reflect the history data.
1.3.6.1.4.1.2544.1.12.8.1.22not-accessiblecurrent
f3EsaProbeHistorySoamPmExtEntry
OBJECT-TYPE
A conceptual row in the f3EsaProbeHistorySoamPmExtTable.
1.3.6.1.4.1.2544.1.12.8.1.22.1not-accessiblecurrent
f3EsaProbeHistorySoamPmExtMinP2RFlr
OBJECT-TYPE
This is the minimum probe to reflector FLR.
1.3.6.1.4.1.2544.1.12.8.1.22.1.1PerfCounter64read-onlycurrent
f3EsaProbeHistorySoamPmExtMaxP2RFlr
OBJECT-TYPE
This is the maximum probe to reflector FLR.
1.3.6.1.4.1.2544.1.12.8.1.22.1.2PerfCounter64read-onlycurrent
f3EsaProbeHistorySoamPmExtAvgP2RFlr
OBJECT-TYPE
This is the average probe to reflector FLR.
1.3.6.1.4.1.2544.1.12.8.1.22.1.3PerfCounter64read-onlycurrent
f3EsaProbeHistorySoamPmExtMinR2PFlr
OBJECT-TYPE
This is the minimum reflector to probe FLR.
1.3.6.1.4.1.2544.1.12.8.1.22.1.4PerfCounter64read-onlycurrent
f3EsaProbeHistorySoamPmExtMaxR2PFlr
OBJECT-TYPE
This is the maximum reflector to probe FLR.
1.3.6.1.4.1.2544.1.12.8.1.22.1.5PerfCounter64read-onlycurrent
f3EsaProbeHistorySoamPmExtAvgR2PFlr
OBJECT-TYPE
This is the average reflector to probe FLR.
1.3.6.1.4.1.2544.1.12.8.1.22.1.6PerfCounter64read-onlycurrent
f3EsaProbeHistorySoamPmExtP2rSeverelyErroredDeltaTs
OBJECT-TYPE
This is the number of delta_ts in which the FLR is greater than availability threshold in the probe to reflector direction.
1.3.6.1.4.1.2544.1.12.8.1.22.1.7PerfCounter64read-onlycurrent
f3EsaProbeHistorySoamPmExtR2PSeverelyErroredDeltaTs
OBJECT-TYPE
This is the number of delta_ts in which the FLR is greater than availability threshold in the reflector to probe direction.
1.3.6.1.4.1.2544.1.12.8.1.22.1.8PerfCounter64read-onlycurrent
f3EsaProbeHistorySoamPmExtP2rAvailableTime
OBJECT-TYPE
This is the probe to reflector available delta_ts which begins to increment when FLR is less than or equal to availability threshold for 'n' consecutive delta_ts. It is incremented until FLR is greater than availability threshold for 'n' consecutive delta_ts.
1.3.6.1.4.1.2544.1.12.8.1.22.1.9PerfCounter64read-onlycurrent
f3EsaProbeHistorySoamPmExtR2PAvailableTime
OBJECT-TYPE
This is the reflector to probe available delta_ts which begins to increment when FLR is less than or equal to availability threshold for 'n' consecutive delta_ts. It is incremented until FLR is greater than availability threshold for 'n' consecutive delta_ts.
1.3.6.1.4.1.2544.1.12.8.1.22.1.10PerfCounter64read-onlycurrent
f3EsaProbeHistorySoamPmExtP2rUnavailableTime
OBJECT-TYPE
This is the probe to reflector unavailable delta_ts which begins to increment when FLR is greater than availability threshold for 'n' consecutive delta_ts. It is incremented until FLR is less than or equal to availability threshold for 'n' consecutive delta_ts.
1.3.6.1.4.1.2544.1.12.8.1.22.1.11PerfCounter64read-onlycurrent
f3EsaProbeHistorySoamPmExtR2PUnavailableTime
OBJECT-TYPE
This is the reflector to probe unavailable delta_ts which begins to increment when FLR is greater than availability threshold for 'n' consecutive delta_ts. It is incremented until FLR is less than or equal to availability threshold for 'n' consecutive delta_ts.
1.3.6.1.4.1.2544.1.12.8.1.22.1.12PerfCounter64read-onlycurrent
f3EsaProbeHistorySoamPmExtMinAbsRTJitter
OBJECT-TYPE
Minimum absolute round-trip (two-way) jitter in a measurement interval.
1.3.6.1.4.1.2544.1.12.8.1.22.1.13PerfCounter64read-onlycurrent
f3EsaProbeHistorySoamPmExtMaxAbsRTJitter
OBJECT-TYPE
Maximum absolute round-trip (two-way) jitter in a measurement interval.
1.3.6.1.4.1.2544.1.12.8.1.22.1.14PerfCounter64read-onlycurrent
f3EsaProbeHistorySoamPmExtAvgAbsRTJitter
OBJECT-TYPE
Average absolute round-trip (two-way) jitter in a measurement interval.
1.3.6.1.4.1.2544.1.12.8.1.22.1.15PerfCounter64read-onlycurrent
f3EsaProbeHistorySoamPmExtNumAbsRTJitter
OBJECT-TYPE
Number of absolute round-trip (two-way) jitter samples.
1.3.6.1.4.1.2544.1.12.8.1.22.1.16PerfCounter64read-onlycurrent
f3EsaProbeHistorySoamPmExtSumAbsRTJitter
OBJECT-TYPE
Sum of absolute round-trip (two-way) jitter samples.
1.3.6.1.4.1.2544.1.12.8.1.22.1.17PerfCounter64read-onlycurrent
f3EsaProbeHistorySoamPmExtSumOfSqAbsRTJitter
OBJECT-TYPE
Sum of squares of absolute round-trip (two-way) jitter samples.
1.3.6.1.4.1.2544.1.12.8.1.22.1.18PerfCounter64read-onlycurrent
f3EsaProbeHistorySoamPmExtMaxP2RFDR
OBJECT-TYPE
Maximum P2R (Forward) FDR in a measurement interval.
1.3.6.1.4.1.2544.1.12.8.1.22.1.19PerfCounter64read-onlycurrent
f3EsaProbeHistorySoamPmExtAvgP2RFDR
OBJECT-TYPE
Average P2R (Forward) FDR in a measurement interval.
1.3.6.1.4.1.2544.1.12.8.1.22.1.20PerfCounter64read-onlycurrent
f3EsaProbeHistorySoamPmExtNumP2RFDR
OBJECT-TYPE
Number of P2R (Forward) FDR samples.
1.3.6.1.4.1.2544.1.12.8.1.22.1.21PerfCounter64read-onlycurrent
f3EsaProbeHistorySoamPmExtSumP2RFDR
OBJECT-TYPE
Sum of P2R (Forward) FDR samples.
1.3.6.1.4.1.2544.1.12.8.1.22.1.22PerfCounter64read-onlycurrent
f3EsaProbeHistorySoamPmExtSumOfSqP2RFDR
OBJECT-TYPE
Sum of squares of P2R (Forward) FDR samples.
1.3.6.1.4.1.2544.1.12.8.1.22.1.23PerfCounter64read-onlycurrent
f3EsaProbeHistorySoamPmExtMaxR2PFDR
OBJECT-TYPE
Maximum R2P (Backward) FDR in a measurement interval.
1.3.6.1.4.1.2544.1.12.8.1.22.1.24PerfCounter64read-onlycurrent
f3EsaProbeHistorySoamPmExtAvgR2PFDR
OBJECT-TYPE
Average R2P (Backward) FDR in a measurement interval.
1.3.6.1.4.1.2544.1.12.8.1.22.1.25PerfCounter64read-onlycurrent
f3EsaProbeHistorySoamPmExtNumR2PFDR
OBJECT-TYPE
Number of R2P (Backward) FDR samples.
1.3.6.1.4.1.2544.1.12.8.1.22.1.26PerfCounter64read-onlycurrent
f3EsaProbeHistorySoamPmExtSumR2PFDR
OBJECT-TYPE
Sum of R2P (Backward) FDR samples.
1.3.6.1.4.1.2544.1.12.8.1.22.1.27PerfCounter64read-onlycurrent
f3EsaProbeHistorySoamPmExtSumOfSqR2PFDR
OBJECT-TYPE
Sum of squares of R2P (Backward) FDR samples.
1.3.6.1.4.1.2544.1.12.8.1.22.1.28PerfCounter64read-onlycurrent
f3EsaProbeHistorySoamPmExtMaxRTFDR
OBJECT-TYPE
Maximum round-trip (two-way) FDR in a measurement interval.
1.3.6.1.4.1.2544.1.12.8.1.22.1.29PerfCounter64read-onlycurrent
f3EsaProbeHistorySoamPmExtAvgRTFDR
OBJECT-TYPE
Average round-trip (two-way) FDR in a measurement interval.
1.3.6.1.4.1.2544.1.12.8.1.22.1.30PerfCounter64read-onlycurrent
f3EsaProbeHistorySoamPmExtNumRTFDR
OBJECT-TYPE
Number of round-trip (two-way) FDR samples.
1.3.6.1.4.1.2544.1.12.8.1.22.1.31PerfCounter64read-onlycurrent
f3EsaProbeHistorySoamPmExtSumRTFDR
OBJECT-TYPE
Sum of round-trip (two-way) FDR samples.
1.3.6.1.4.1.2544.1.12.8.1.22.1.32PerfCounter64read-onlycurrent
f3EsaProbeHistorySoamPmExtSumOfSqRTFDR
OBJECT-TYPE
Sum of squares of round-trip (two-way) FDR samples.
1.3.6.1.4.1.2544.1.12.8.1.22.1.33PerfCounter64read-onlycurrent
f3EsaProbeHistorySoamPmExtP2rAvailableDeltaTs
OBJECT-TYPE
Probe to reflector available delta_ts which begins to increment when FLR is less than or equal to availability threshold for 'n' consecutive delta_ts.
1.3.6.1.4.1.2544.1.12.8.1.22.1.34PerfCounter64read-onlycurrent
f3EsaProbeHistorySoamPmExtR2pAvailableDeltaTs
OBJECT-TYPE
Reflector to probe available delta_ts which begins to increment when FLR is less than or equal to availability threshold for 'n' consecutive delta_ts.
1.3.6.1.4.1.2544.1.12.8.1.22.1.35PerfCounter64read-onlycurrent
f3EsaProbeHistorySoamPmExtP2rUnavailableDeltaTs
OBJECT-TYPE
Probe to reflector unavailable delta_ts which begins to increment when FLR is greater than availability threshold for 'n' consecutive delta_ts.
1.3.6.1.4.1.2544.1.12.8.1.22.1.36PerfCounter64read-onlycurrent
f3EsaProbeHistorySoamPmExtR2pUnavailableDeltaTs
OBJECT-TYPE
Reflector to probe unavailable delta_ts which begins to increment when FLR is greater than availability threshold for 'n' consecutive delta_ts.
1.3.6.1.4.1.2544.1.12.8.1.22.1.37PerfCounter64read-onlycurrent
f3EsaProbeHistorySoamPmExtElapsedTime
OBJECT-TYPE
The elapsed time (monotonic time) for the interval which could be less or more than measurement interval based on which the Time of Day was moved forward or backwards respectively (miliseconds).
1.3.6.1.4.1.2544.1.12.8.1.22.1.38PerfCounter64read-onlycurrent
cmServAssuranceNotifications
OBJECT-IDENTITY
1.3.6.1.4.1.2544.1.12.8.2
cmServAssuranceConformance
OBJECT-IDENTITY
1.3.6.1.4.1.2544.1.12.8.3
cmServAssuranceCompliances
OBJECT-IDENTITY
1.3.6.1.4.1.2544.1.12.8.3.1
cmServAssuranceGroups
OBJECT-IDENTITY
1.3.6.1.4.1.2544.1.12.8.3.2

Notifications

NameOIDStatus
cmOperateLoopbackTrap
NOTIFICATION-TYPE
This is the Operate Loopback Notification sent by the agent. The actual attribute value is sent by the agent in the form of a varbind list, as additional objects, as per SMIv2 (RFC2578, Section 8.1).
1.3.6.1.4.1.2544.1.12.8.2.1current
cmReleaseLoopbackTrap
NOTIFICATION-TYPE
This is the Release Loopback Notification sent by the agent. The actual attribute value is sent by the agent in the form of a varbind list, as additional objects, as per SMIv2 (RFC2578, Section 8.1).
1.3.6.1.4.1.2544.1.12.8.2.2current
esaProbeThresholdCrossingAlert
NOTIFICATION-TYPE
This trap is sent each time a threshold on a PM condition on ESA Probe is crossed.
1.3.6.1.4.1.2544.1.12.8.2.3current

Conformance

NameOIDStatus
cmServAssuranceCompliance
MODULE-COMPLIANCE
Describes the requirements for conformance to the CM ServAssurance group.
1.3.6.1.4.1.2544.1.12.8.3.1.1current
cmServAssuranceObjectGroup
OBJECT-GROUP
***************** THIS OBJECT GROUP IS NOW DEPRECATED *************** A collection of objects used to manage the CM ServAssurance group.
1.3.6.1.4.1.2544.1.12.8.3.2.1deprecated
cmServAssuranceNotifGroup
NOTIFICATION-GROUP
***************** THIS OBJECT GROUP IS NOW DEPRECATED ****************** A collection of notifications used in the CM ServAssurance group.
1.3.6.1.4.1.2544.1.12.8.3.2.2deprecated
cmEcpaGroup
OBJECT-GROUP
A collection of objects used to manage the CM ServAssurance ECPA functionality.
1.3.6.1.4.1.2544.1.12.8.3.2.3current
cmEsaGroup
OBJECT-GROUP
A collection of objects used to manage the CM ServAssurance ESA functionality.
1.3.6.1.4.1.2544.1.12.8.3.2.4current
cmServAssuranceGenNotifGroup
NOTIFICATION-GROUP
A collection of notifications used in the generic CM ServAssurance functionality.
1.3.6.1.4.1.2544.1.12.8.3.2.5current
cmServAssuranceEsaNotifGroup
NOTIFICATION-GROUP
A collection of notifications used in the CM ServAssurance ESA functionality.
1.3.6.1.4.1.2544.1.12.8.3.2.6current
cmBertGroup
OBJECT-GROUP
A collection of objects used to manage the CM ServAssurance BERT functionality.
1.3.6.1.4.1.2544.1.12.8.3.2.7current