MIBs Depot

CM-SAT-MIB

Registered at
1.3.6.1.4.1.2544.1.12.28
Last updated
2017-04-05 00:00
Organization
ADVA Optical Networking SE
Revisions
2017-04-05 00:00
Namespace
adva
Source file
CM-SAT-MIB
Digest
sha256:a43cf77e3c67dfa373a130a99e225ee395d8aa79651118e688c9ced431560501

Description

This module defines the Service Activation MIB definitions used by the F3 (FSP150CM/CC) product lines. Copyright (C) ADVA.

Contact

Web URL: http://adva.com/ E-mail: support@adva.com Postal: ADVA Optical Networking SE Campus Martinsried Fraunhoferstrasse 9a 82152 Martinsried/Munich Germany Phone: +49 089 89 06 65 0 Fax: +49 089 89 06 65 199

Imports

FromSymbols
ADVA-MIBfsp150cm
CM-COMMON-MIBAdminState, CmPmBinAction, MepDestinationType, OperationalState, SecondaryState, VlanId, VlanPriority
CM-ENTITY-MIBneIndex, networkElementEntry, shelfIndex, slotIndex
CM-FACILITY-MIBPolicerColorMode
CM-SA-MIBEsaProbePktIntervalType
IEEE8021-CFM-MIBDot1agCfmMepIdOrZero, dot1agCfmMepEntry
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP
SNMPv2-SMICounter64, Integer32, IpAddress, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, Unsigned32, iso
SNMPv2-TCDateAndTime, DisplayString, MacAddress, RowStatus, StorageType, TEXTUAL-CONVENTION, TruthValue, VariablePointer

Imported by

Nothing in this corpus imports this module.

Load order

Every file a consumer needs in order to load this module, dependencies first.

ADVA-MIB
BRIDGE-MIB
CM-COMMON-MIB
CM-ENTITY-MIB
CM-FACILITY-MIB
CM-REDUNDANCY-MIB
CM-SA-MIB
CM-SAT-MIB
CM-SYSTEM-MIB
ENTITY-MIB
F3-LAG-MIB
F3-SYNC-MIB
IANA-ADDRESS-FAMILY-NUMBERS-MIB
IANA-ENTITY-MIB
IANAifType-MIB
IEEE8021-CFM-MIB
IEEE8021-TC-MIB
IF-MIB
IPV6-TC
LLDP-MIB
LLDP-V2-MIB
LLDP-V2-TC-MIB
P-BRIDGE-MIB
Q-BRIDGE-MIB
RFC1158-MIB
RFC1271-MIB
RMON-MIB
RMON2-MIB
SNMP-FRAMEWORK-MIB
SNMP-TARGET-MIB
SNMPv2-CONF
SNMPv2-MIB
SNMPv2-SMI
SNMPv2-TC
TOKEN-RING-RMON-MIB
UUID-TC-MIB

Textual conventions

NameOIDSyntaxAccessStatus
SatDirection
TEXTUAL-CONVENTION
The direction of Service Activation Test.
current
SatFramePayloadType
TEXTUAL-CONVENTION
This object describes the Payload type of Service Activation Test frame.
current
SatProceduresList
TEXTUAL-CONVENTION
Bit Mask that specifies all the Service Activation Test procedure.
current
SatProceduresType
TEXTUAL-CONVENTION
All procedures type of the Service Activation Test.
current
SatResult
TEXTUAL-CONVENTION
This object describes the result of Service Activation Test.
current
SatStatus
TEXTUAL-CONVENTION
The status of the overall Service Activation Test.
current
SatTestAction
TEXTUAL-CONVENTION
This object describes the operation on Service Activation Test frame Payload type.
current
ServiceActivationTestMode
TEXTUAL-CONVENTION
The test mode of Service Activation Test.
current

Objects

NameOIDSyntaxAccessStatus
cmServActivationObjects
OBJECT-IDENTITY
1.3.6.1.4.1.2544.1.12.28.1
satControlTable
OBJECT-TYPE
A list of entries for the control of SAT Control.
1.3.6.1.4.1.2544.1.12.28.1.1not-accessiblecurrent
satControlEntry
OBJECT-TYPE
A conceptual row in the satControlTable.
1.3.6.1.4.1.2544.1.12.28.1.1.1not-accessiblecurrent
satControlIndex
OBJECT-TYPE
The index of the Service Activation Test.
1.3.6.1.4.1.2544.1.12.28.1.1.1.1Integer32not-accessiblecurrent
satControlName
OBJECT-TYPE
The alias of the Service Activation Test.
1.3.6.1.4.1.2544.1.12.28.1.1.1.2DisplayString (SIZE(0..16))read-writecurrent
satControlTestMode
OBJECT-TYPE
The mode of the Service Activation Test.
1.3.6.1.4.1.2544.1.12.28.1.1.1.3ServiceActivationTestModeread-writecurrent
satControlTestProcedures
OBJECT-TYPE
A List of Service Activation Test procedures.
1.3.6.1.4.1.2544.1.12.28.1.1.1.4SatProceduresListread-writecurrent
satControlConfigTestDuration
OBJECT-TYPE
The duration of CIR step test, expressed in seconds.
1.3.6.1.4.1.2544.1.12.28.1.1.1.5Integer32read-writecurrent
satControlConfigCIRTestStepNum
OBJECT-TYPE
The number of steps in CIR step test.
1.3.6.1.4.1.2544.1.12.28.1.1.1.6Integer32 (1..10)read-writecurrent
satControlConfigCIRTestStepDuration
OBJECT-TYPE
The duration of each CIR step test.
1.3.6.1.4.1.2544.1.12.28.1.1.1.7Integer32 (1..60)read-writecurrent
satControlPerfTestDuration
OBJECT-TYPE
The duration of the SAT Performance Test, expressed in minutes.
1.3.6.1.4.1.2544.1.12.28.1.1.1.8Integer32read-writecurrent
satControlStatus
OBJECT-TYPE
The overall SAT Control Test Status.
1.3.6.1.4.1.2544.1.12.28.1.1.1.9SatStatusread-onlycurrent
satControlAction
OBJECT-TYPE
The start/stop action of the SAT Control.
1.3.6.1.4.1.2544.1.12.28.1.1.1.10SatTestActionread-writecurrent
satControlStorageType
OBJECT-TYPE
The type of storage configured for this entry.
1.3.6.1.4.1.2544.1.12.28.1.1.1.11StorageTyperead-createcurrent
satControlRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of satControlRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with satControlRowStatus value as createAndGo(4). Upon successful row creation, this variable has a value of active(1). The satControlRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.28.1.1.1.12RowStatusread-createcurrent
satControlFailCause
OBJECT-TYPE
The information about the reason of the Test failure.
1.3.6.1.4.1.2544.1.12.28.1.1.1.13DisplayStringread-onlycurrent
satControlTestStartTime
OBJECT-TYPE
The start time of this SAT Control.
1.3.6.1.4.1.2544.1.12.28.1.1.1.14DateAndTimeread-onlycurrent
satControlFlpduTagOverride
OBJECT-TYPE
Whether permit user to configure FLPDU explicitly. Disabled: FLPDUs tag is inherited from SCM of MEP. Enabled: User can configure FLPDUs tag explicitly, which will override the VLAN tags from MEP.
1.3.6.1.4.1.2544.1.12.28.1.1.1.15TruthValueread-writecurrent
satStreamTable
OBJECT-TYPE
A list of entries for the control of SAT Streams.
1.3.6.1.4.1.2544.1.12.28.1.2not-accessiblecurrent
satStreamEntry
OBJECT-TYPE
A conceptual row in the satStreamTable.
1.3.6.1.4.1.2544.1.12.28.1.2.1not-accessiblecurrent
satStreamIndex
OBJECT-TYPE
The index of the Service Activation Test Stream.
1.3.6.1.4.1.2544.1.12.28.1.2.1.1Integer32not-accessiblecurrent
satStreamName
OBJECT-TYPE
The alias of the Service Activation Test Stream.
1.3.6.1.4.1.2544.1.12.28.1.2.1.2DisplayString (SIZE(0..64))read-writecurrent
satStreamTestPort
OBJECT-TYPE
The related port of the Service Activation Test Stream.
1.3.6.1.4.1.2544.1.12.28.1.2.1.3VariablePointerread-writecurrent
satStreamTestDirection
OBJECT-TYPE
The direction of the Service Activation Test Stream.
1.3.6.1.4.1.2544.1.12.28.1.2.1.4SatDirectionread-writecurrent
satStreamDestMacAddress
OBJECT-TYPE
This object describes the destination MAC address of FLPDU.
1.3.6.1.4.1.2544.1.12.28.1.2.1.5MacAddressread-writecurrent
satStreamFramePayloadType
OBJECT-TYPE
The type of Payload of the Frame Loss PDU.
1.3.6.1.4.1.2544.1.12.28.1.2.1.6SatFramePayloadTyperead-writecurrent
satStreamCustomFramePayload
OBJECT-TYPE
This object describes the customized frame payload.
1.3.6.1.4.1.2544.1.12.28.1.2.1.7DisplayString (SIZE(0..16))read-writecurrent
satStreamFrameSizeList
OBJECT-TYPE
This object describes a list of Frame Sizes used in FLPDU.
1.3.6.1.4.1.2544.1.12.28.1.2.1.8DisplayStringread-writecurrent
satStreamSacProfileId
OBJECT-TYPE
This object describes the related Service Acceptance Criteria (SAC) Profile Id.
1.3.6.1.4.1.2544.1.12.28.1.2.1.9VariablePointerread-writecurrent
satStreamSrcMepId
OBJECT-TYPE
This object describes the Local MEP related with SAT Test Stream.
1.3.6.1.4.1.2544.1.12.28.1.2.1.10VariablePointerread-writecurrent
satStreamDestMepType
OBJECT-TYPE
This object describes the type of Destination MEP, which can be based on MEP id or MAC Address. This is applicable only if satStreamDestMepEnabled is true.
1.3.6.1.4.1.2544.1.12.28.1.2.1.11MepDestinationTyperead-writecurrent
satStreamDestMepId
OBJECT-TYPE
This object describes the destination MEP id. This is applicable only if satStreamDestMepEnabled is true.
1.3.6.1.4.1.2544.1.12.28.1.2.1.12Integer32read-writecurrent
satStreamDestMepMacAddr
OBJECT-TYPE
This object describes the Destination MEP's MAC Address. This is applicable only if satStreamDestMepEnabled is true.
1.3.6.1.4.1.2544.1.12.28.1.2.1.13MacAddressread-writecurrent
satStreamDmmPacketSize
OBJECT-TYPE
This object describes the Delay Measurement Message (DMM) frame size.
1.3.6.1.4.1.2544.1.12.28.1.2.1.14Integer32read-writecurrent
satStreamDmmPacketInterval
OBJECT-TYPE
This object describes the Delay Measurement Message (DMM) frame generation interval.
1.3.6.1.4.1.2544.1.12.28.1.2.1.15EsaProbePktIntervalTyperead-writecurrent
satStreamOverallResult
OBJECT-TYPE
This object describes the test result.
1.3.6.1.4.1.2544.1.12.28.1.2.1.16SatResultread-onlycurrent
satStreamAction
OBJECT-TYPE
This object describes the operation on this test.
1.3.6.1.4.1.2544.1.12.28.1.2.1.17SatTestActionread-writecurrent
satStreamStatus
OBJECT-TYPE
This object describes the test status of this Test Stream.
1.3.6.1.4.1.2544.1.12.28.1.2.1.18SatStatusread-onlycurrent
satStreamCurrentTestProcedure
OBJECT-TYPE
This object describes the current test procedure.
1.3.6.1.4.1.2544.1.12.28.1.2.1.19SatProceduresTyperead-onlycurrent
satStreamCurrentConfigCirTestStep
OBJECT-TYPE
This object describes the current step number of CIR Test.
1.3.6.1.4.1.2544.1.12.28.1.2.1.20Integer32read-onlycurrent
satStreamInner1VlanId
OBJECT-TYPE
This object describes the Inner1 VLAN Id.
1.3.6.1.4.1.2544.1.12.28.1.2.1.21VlanIdread-writecurrent
satStreamInner1VlanPri
OBJECT-TYPE
This object describes the Inner1 VLAN Priority.
1.3.6.1.4.1.2544.1.12.28.1.2.1.22VlanPriorityread-writecurrent
satStreamInner1VlanEnabled
OBJECT-TYPE
This object describes whether the Inner1 VLAN enabled.
1.3.6.1.4.1.2544.1.12.28.1.2.1.23TruthValueread-writecurrent
satStreamInner1ValnEtherType
OBJECT-TYPE
This object describes the Inner2 VLAN EtherType.
1.3.6.1.4.1.2544.1.12.28.1.2.1.24Integer32read-writecurrent
satStreamInner2VlanId
OBJECT-TYPE
This object describes the Inner2 VLAN Id.
1.3.6.1.4.1.2544.1.12.28.1.2.1.25VlanIdread-writecurrent
satStreamInner2VlanPri
OBJECT-TYPE
This object describes the Inner2 VLAN Priority.
1.3.6.1.4.1.2544.1.12.28.1.2.1.26VlanPriorityread-writecurrent
satStreamInner2VlanEnabled
OBJECT-TYPE
This object describes whether the Inner2 VLAN enabled.
1.3.6.1.4.1.2544.1.12.28.1.2.1.27TruthValueread-writecurrent
satStreamInner2VlanEtherType
OBJECT-TYPE
This object describes whether the Inner2 VLAN ether type.
1.3.6.1.4.1.2544.1.12.28.1.2.1.28Integer32read-writecurrent
satStreamOuterVlanId
OBJECT-TYPE
This object describes the Outer VLAN Id.
1.3.6.1.4.1.2544.1.12.28.1.2.1.29VlanIdread-writecurrent
satStreamOuterVlanPri
OBJECT-TYPE
This object describes the Outer VLAN Priority.
1.3.6.1.4.1.2544.1.12.28.1.2.1.30VlanPriorityread-writecurrent
satStreamOuterVlanEnabled
OBJECT-TYPE
This object describes whether the Outer VLAN enabled.
1.3.6.1.4.1.2544.1.12.28.1.2.1.31TruthValueread-writecurrent
satStreamOuterVlanEtherType
OBJECT-TYPE
This object describes whether the Outer VLAN Ethertype.
1.3.6.1.4.1.2544.1.12.28.1.2.1.32Integer32read-writecurrent
satStreamDeiEnabled
OBJECT-TYPE
This object describes whether the DEI enabled.
1.3.6.1.4.1.2544.1.12.28.1.2.1.33TruthValueread-writecurrent
satStreamGreenPcp
OBJECT-TYPE
This object describes the PCP value for Green Packets.
1.3.6.1.4.1.2544.1.12.28.1.2.1.34Integer32read-writecurrent
satStreamYellowPcp
OBJECT-TYPE
This object describes the PCP value for Yellow Packets.
1.3.6.1.4.1.2544.1.12.28.1.2.1.35Integer32read-writecurrent
satStreamColorMode
OBJECT-TYPE
This object describes the color mode for Policing test.
1.3.6.1.4.1.2544.1.12.28.1.2.1.36PolicerColorModeread-writecurrent
satStreamCirLo
OBJECT-TYPE
This object describes CIR low 32 bits.
1.3.6.1.4.1.2544.1.12.28.1.2.1.37Unsigned32read-writecurrent
satStreamCirHi
OBJECT-TYPE
This object describes CIR high 32 bits.
1.3.6.1.4.1.2544.1.12.28.1.2.1.38Unsigned32read-writecurrent
satStreamEirLo
OBJECT-TYPE
This object describes EIR low 32 bits.
1.3.6.1.4.1.2544.1.12.28.1.2.1.39Unsigned32read-writecurrent
satStreamEirHi
OBJECT-TYPE
This object describes EIR high 32 bits.
1.3.6.1.4.1.2544.1.12.28.1.2.1.40Unsigned32read-writecurrent
satStreamCbs
OBJECT-TYPE
This object describes CBS.
1.3.6.1.4.1.2544.1.12.28.1.2.1.41Unsigned32read-writecurrent
satStreamEbs
OBJECT-TYPE
This object describes CBS.
1.3.6.1.4.1.2544.1.12.28.1.2.1.42Unsigned32read-writecurrent
satStreamStorageType
OBJECT-TYPE
The type of storage configured for this entry.
1.3.6.1.4.1.2544.1.12.28.1.2.1.43StorageTyperead-createcurrent
satStreamRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of satStreamRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with satStreamRowStatus value as createAndGo(4). Upon successful row creation, this variable has a value of active(1). The satStreamRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.28.1.2.1.44RowStatusread-createcurrent
satStreamDmmPktPriority
OBJECT-TYPE
This object describes the Dmm packet priority.
1.3.6.1.4.1.2544.1.12.28.1.2.1.45VlanPriorityread-writecurrent
satStreamMFactor
OBJECT-TYPE
The M factor is used in test result validation. It is added to allow for the effect of the traffic policer's CBS and EBS settings and test time. Roughly, it equals to EBS/Test Duration, user should configure its value based on experience test.
1.3.6.1.4.1.2544.1.12.28.1.2.1.46Unsigned32read-writecurrent
satStreamDestMepEnabled
OBJECT-TYPE
For a SAT two-way test, the remote end is expected to have a loopback for FLPDUs, but it may or may not have a Responder MEP to process DMMs. This object indicates whether the remote end has a Responder MEP or not. If the Responder MEP is present, two-way delay is computed by the Controller MEP once DMR is received, if the Responder MEP is not present, the two-way delay is computed when the Controller MEP receives the looped back DMM.
1.3.6.1.4.1.2544.1.12.28.1.2.1.47TruthValueread-writecurrent
satStreamLlActivateEnabled
OBJECT-TYPE
This attribute specifies whether Latching Loopback needs to be activated for the SAT stream during a SAT test. It is only applicable for two way test.
1.3.6.1.4.1.2544.1.12.28.1.2.1.48TruthValueread-writecurrent
satResultStatsTable
OBJECT-TYPE
A list of entries for the control of SAT Result Statistics.
1.3.6.1.4.1.2544.1.12.28.1.3not-accessiblecurrent
satResultStatsEntry
OBJECT-TYPE
A conceptual row in the satResultStatsTable.
1.3.6.1.4.1.2544.1.12.28.1.3.1not-accessiblecurrent
satResultStatsTestType
OBJECT-TYPE
The Test Type of the Service Activation Test.
1.3.6.1.4.1.2544.1.12.28.1.3.1.1SatProceduresTypenot-accessiblecurrent
satResultStatsStepNumber
OBJECT-TYPE
The Test step number of the Service Activation Test.
1.3.6.1.4.1.2544.1.12.28.1.3.1.2Integer32not-accessiblecurrent
satResultStatsSessionId
OBJECT-TYPE
The session id of the Service Activation Test.
1.3.6.1.4.1.2544.1.12.28.1.3.1.3Unsigned32read-onlycurrent
satResultStatsStartTime
OBJECT-TYPE
The start time of the Service Activation Test.
1.3.6.1.4.1.2544.1.12.28.1.3.1.4DateAndTimeread-onlycurrent
satResultStatsEndTime
OBJECT-TYPE
The end time of the Service Activation Test.
1.3.6.1.4.1.2544.1.12.28.1.3.1.5DateAndTimeread-onlycurrent
satResultStatsStatus
OBJECT-TYPE
The Status of the Service Activation Test.
1.3.6.1.4.1.2544.1.12.28.1.3.1.6SatStatusread-onlycurrent
satResultStatsResult
OBJECT-TYPE
This object describes SAT whether pass.
1.3.6.1.4.1.2544.1.12.28.1.3.1.7SatResultread-onlycurrent
satResultStatsMinIRGMeasured
OBJECT-TYPE
This object describes the minimum Information Rate (IR) for Green Packets.
1.3.6.1.4.1.2544.1.12.28.1.3.1.8Counter64read-onlycurrent
satResultStatsAvgIRGMeasured
OBJECT-TYPE
This object describes the average Information Rate (IR) for Green Packets.
1.3.6.1.4.1.2544.1.12.28.1.3.1.9Counter64read-onlycurrent
satResultStatsMaxIRGMeasured
OBJECT-TYPE
This object describes the maximum Information Rate (IR) for Green Packets.
1.3.6.1.4.1.2544.1.12.28.1.3.1.10Counter64read-onlycurrent
satResultStatsMinIRYMeasured
OBJECT-TYPE
This object describes the minimum Information Rate (IR) for Yellow Packets.
1.3.6.1.4.1.2544.1.12.28.1.3.1.11Counter64read-onlycurrent
satResultStatsAvgIRYMeasured
OBJECT-TYPE
This object describes the average Information Rate (IR) for Yellow Packets.
1.3.6.1.4.1.2544.1.12.28.1.3.1.12Counter64read-onlycurrent
satResultStatsMaxIRYMeasured
OBJECT-TYPE
This object describes the maximum Information Rate (IR) for Yellow Packets.
1.3.6.1.4.1.2544.1.12.28.1.3.1.13Counter64read-onlycurrent
satResultStatsFlrGMeasured
OBJECT-TYPE
This object describes the Frame Loss Ratio (FLR) for Green Packets. From the EGX8.2 and GE110 7.1, If its value is 26000001, it means 26.000001% frame lost. For the earlier release, If its value is 260001, it means 26.0001% frame lost.
1.3.6.1.4.1.2544.1.12.28.1.3.1.14Integer32read-onlycurrent
satResultStatsFlrYMeasured
OBJECT-TYPE
This object describes the Frame Loss Ratio (FLR) for Yellow Packets. From the EGX8.2 and GE110 7.1, If its value is 26000001, it means 26.000001% frame lost. For the earlier release, If its value is 260001, it means 26.0001% frame lost.
1.3.6.1.4.1.2544.1.12.28.1.3.1.15Integer32read-onlycurrent
satResultStatsFlrGCounts
OBJECT-TYPE
This object describes the Frame Loss (FL) count for Green Packets.
1.3.6.1.4.1.2544.1.12.28.1.3.1.16Counter64read-onlycurrent
satResultStatsFlrYCounts
OBJECT-TYPE
This object describes the Frame Loss (FL) count for Yellow Packets.
1.3.6.1.4.1.2544.1.12.28.1.3.1.17Counter64read-onlycurrent
satResultStatsMinFTDGMeasured
OBJECT-TYPE
This object describes the minimum Frame Transfer Delay (FTD) for Green Packets.
1.3.6.1.4.1.2544.1.12.28.1.3.1.18Unsigned32read-onlycurrent
satResultStatsAvgFTDGMeasured
OBJECT-TYPE
This object describes the average Frame Transfer Delay (FTD) for Green Packets.
1.3.6.1.4.1.2544.1.12.28.1.3.1.19Unsigned32read-onlycurrent
satResultStatsMaxFTDGMeasured
OBJECT-TYPE
This object describes the maximum Frame Transfer Delay (FTD) for Green Packets.
1.3.6.1.4.1.2544.1.12.28.1.3.1.20Unsigned32read-onlycurrent
satResultStatsIMinFDVGMeasured
OBJECT-TYPE
This object describes the minimum Frame Delay Variation (FDV) for Green Packets.
1.3.6.1.4.1.2544.1.12.28.1.3.1.21Unsigned32read-onlycurrent
satResultStatsIAvgFDVGMeasured
OBJECT-TYPE
This object describes the average Frame Delay Variation (FDV) for Green Packets.
1.3.6.1.4.1.2544.1.12.28.1.3.1.22Unsigned32read-onlycurrent
satResultStatsIMaxFDVGMeasured
OBJECT-TYPE
This object describes the maximum Frame Delay Variation (FDV) for Green Packets.
1.3.6.1.4.1.2544.1.12.28.1.3.1.23Unsigned32read-onlycurrent
satResultStatsISyncErrorsNum
OBJECT-TYPE
The number of (time) Synchronization Errors between SAT Control and SAT Responder in the current Test.
1.3.6.1.4.1.2544.1.12.28.1.3.1.24Unsigned32read-onlycurrent
satResultStatsIfNegFLG
OBJECT-TYPE
This object means whether negative green frame loss. True: negative loss of green packets occurs, which means receiving more green packets than expected. False: negative loss of green packets doesn't occur, which means not receiving more green packets than expected.
1.3.6.1.4.1.2544.1.12.28.1.3.1.25TruthValueread-onlycurrent
satResultStatsIfNegFLY
OBJECT-TYPE
This object means whether negative yellow frame loss. True: negative loss of yellow packets occurs, which means receiving more yellow packets than expected. False: negative loss of yellow packets doesn't occur, which means not receiving more yellow packets than expected.
1.3.6.1.4.1.2544.1.12.28.1.3.1.26TruthValueread-onlycurrent
satResultStatsAvgIRT
OBJECT-TYPE
This object describes Average IR of total packets, non distinguishing green or yellow. Only valid for color blind test.
1.3.6.1.4.1.2544.1.12.28.1.3.1.27Counter64read-onlycurrent
satResultStatsFlrTMeasured
OBJECT-TYPE
This object describes the Frame Loss Ratio (FLR) for Total Packets. No distinguish color, negative value means receiving much more packets than expected. Only valid for color blind test. If its value is 26000001, it means 26.000001% frame lost.
1.3.6.1.4.1.2544.1.12.28.1.3.1.28Integer32read-onlycurrent
satResultStatsFlTCounts
OBJECT-TYPE
This object describes the Frame Loss (FL) count for Total Packets.
1.3.6.1.4.1.2544.1.12.28.1.3.1.29Counter64read-onlycurrent
satResultStatsIfNegFLT
OBJECT-TYPE
This object means whether negative total frame loss. True: negative loss of green packets occurs, which means receiving more green packets than expected. False: negative loss of green packets doesn't occur, which means not receiving more green packets than expected.
1.3.6.1.4.1.2544.1.12.28.1.3.1.30TruthValueread-onlycurrent
satSacProfileTable
OBJECT-TYPE
A list of entries for the control of SAT Service Acceptance Criteria (SAC) Profile.
1.3.6.1.4.1.2544.1.12.28.1.4not-accessiblecurrent
satSacProfileEntry
OBJECT-TYPE
A conceptual row in the satSacProfileTable.
1.3.6.1.4.1.2544.1.12.28.1.4.1not-accessiblecurrent
satSacProfileIndex
OBJECT-TYPE
The index of SAT Service Acceptance Criteria (SAC) Profile.
1.3.6.1.4.1.2544.1.12.28.1.4.1.1Integer32not-accessiblecurrent
satSacProfileAlias
OBJECT-TYPE
The alias of SAT Service Acceptance Criteria (SAC) Profile.
1.3.6.1.4.1.2544.1.12.28.1.4.1.2DisplayString (SIZE(0..64))read-writecurrent
satSacProfileFLR
OBJECT-TYPE
The Frame Loss Ratio (FLR) acceptance criteria of this SAC Profile. From the EGX8.2 and GE110 7.1, If its value is 26000001, it means 26.000001% frame lost. For the earlier release, If its value is 260001, it means 26.0001% frame lost.
1.3.6.1.4.1.2544.1.12.28.1.4.1.3Integer32read-writecurrent
satSacProfileFTD
OBJECT-TYPE
The Frame Transfer Delay (FTD) acceptance criteria of this SAC Profile.
1.3.6.1.4.1.2544.1.12.28.1.4.1.4Unsigned32read-writecurrent
satSacProfileFDV
OBJECT-TYPE
The frame transfer delay variation of SAT Service Acceptance Criteria (SAC) Profile.
1.3.6.1.4.1.2544.1.12.28.1.4.1.5Unsigned32read-writecurrent
satSacProfileStorageType
OBJECT-TYPE
The type of storage configured for this entry.
1.3.6.1.4.1.2544.1.12.28.1.4.1.6StorageTyperead-createcurrent
satSacProfileRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of satSacProfileRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with satSacProfileRowStatus value as createAndGo(4). Upon successful row creation, this variable has a value of active(1). The satSacProfileRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.28.1.4.1.7RowStatusread-createcurrent
satResponderSessionTable
OBJECT-TYPE
A list of entries for the control of SAT Responder Session.
1.3.6.1.4.1.2544.1.12.28.1.5not-accessiblecurrent
satResponderSessionEntry
OBJECT-TYPE
A conceptual row in the satResponderSessionTable.
1.3.6.1.4.1.2544.1.12.28.1.5.1not-accessiblecurrent
satResponderSessionIndex
OBJECT-TYPE
The index of the entry.
1.3.6.1.4.1.2544.1.12.28.1.5.1.1Unsigned32not-accessiblecurrent
satResponderSessionId
OBJECT-TYPE
The id of active test session negotiated between SAT Responder and SAT Control.
1.3.6.1.4.1.2544.1.12.28.1.5.1.2Unsigned32read-onlycurrent
satResponderSessionControlMepMacAddr
OBJECT-TYPE
This object describes the Control MEP's MAC Address.
1.3.6.1.4.1.2544.1.12.28.1.5.1.3MacAddressread-onlycurrent
satResponderSessionMepId
OBJECT-TYPE
The local MEP Id.
1.3.6.1.4.1.2544.1.12.28.1.5.1.4VariablePointerread-onlycurrent
satResponderSessionStorageType
OBJECT-TYPE
The type of storage configured for this entry.
1.3.6.1.4.1.2544.1.12.28.1.5.1.5StorageTyperead-createcurrent
satResponderSessionRowStatus
OBJECT-TYPE
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of satResponderSessionRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with satResponderSessionRowStatus value as createAndGo(4). Upon successful row creation, this variable has a value of active(1). The satResponderSessionRowStatus object may be modified if the associated instance of this object is equal to active(1).
1.3.6.1.4.1.2544.1.12.28.1.5.1.6RowStatusread-createcurrent
networkElementSatParamsTable
OBJECT-TYPE
Entries may be auto discovered, or can be explicitly created by SNMP Manager. Each remotely discovered shelf is represented as a row in this table.
1.3.6.1.4.1.2544.1.12.28.1.6not-accessiblecurrent
networkElementSatParamsEntry
OBJECT-TYPE
A conceptual row in the networkElementSatParamsTable.
1.3.6.1.4.1.2544.1.12.28.1.6.1not-accessiblecurrent
neSatParamsEtherType
OBJECT-TYPE
This object describes the SAT System EtherType.
1.3.6.1.4.1.2544.1.12.28.1.6.1.1Unsigned32read-writecurrent
satCfmMepExtTable
OBJECT-TYPE
This objects describe the SAT responder whether enabled on the MEP.
1.3.6.1.4.1.2544.1.12.28.1.7not-accessiblecurrent
satCfmMepExtEntry
OBJECT-TYPE
A conceptual row in the satCfmMepExtTable.
1.3.6.1.4.1.2544.1.12.28.1.7.1not-accessiblecurrent
satCfmMepSatResponderEnabled
OBJECT-TYPE
This objects describes the SAT Responder whether enabled on the MEP.
1.3.6.1.4.1.2544.1.12.28.1.7.1.1TruthValueread-writecurrent
cmServActivationNotifications
OBJECT-IDENTITY
1.3.6.1.4.1.2544.1.12.28.2
cmServActivationConformance
OBJECT-IDENTITY
1.3.6.1.4.1.2544.1.12.28.3
cmServActivationCompliances
OBJECT-IDENTITY
1.3.6.1.4.1.2544.1.12.28.3.1
cmServActivationGroups
OBJECT-IDENTITY
1.3.6.1.4.1.2544.1.12.28.3.2

Conformance

NameOIDStatus
cmServActivationCompliance
MODULE-COMPLIANCE
Describes the requirements for conformance to the CM SAT group.
1.3.6.1.4.1.2544.1.12.28.3.1.1current
cmSatGroup
OBJECT-GROUP
A collection of objects used to manage the CM SAT functionality.
1.3.6.1.4.1.2544.1.12.28.3.2.1current