TIMETRA-FILTER-MIB

TEXTUAL-CONVENTION

Uniquely identifies an entry in a policy or filter table.

TEXTUAL-CONVENTION

Represents a filter Id. Any value greater than 65535 indicates a filter that was created (auto-generated) by the system. - The range 0x01000000 through 0x0100FFFF indicates a filter used for BGP Flow-Spec. In this case, the last 15 bits indicate the value of the vRtrID where the filter is active. Values higher than 0x01008000 represent flowspec group filters. - The range 0x03000000 through 0x0300FFFF indicates a filter used for Open-Flow. - The range 0x20000000 .. 0x3FFFFFFF is used for handling filter rules (received from RADIUS) that are to be shared between users. The Id is encoded as follows: - the highest 3 bits (0b001) indicate that it is an auto-generated shared filter - the subsequent 13 bits indicate which combination of filter rules are inserted; this corresponds to the second number in the filter Id as displayed in CLI: the '1' in the example '9:1' - the subsequent 16 bits indicate the base filter Id; this corresponds to the first number ('9') in '9:1' - The range 0x10000000 .. 0x1FFFFFFF is used for handling filter flow-rules (received from DIAMETER) that are to be shared between users. The Id is encoded as follows: - the highest 4 bits (0b0001) indicate that it is an auto-generated flow-rule filter - the subsequent 12 bits indicate which combination of flow-rules are inserted; this corresponds to the second number in the filter Id as displayed in CLI: the '2' in the example '9:P2' - the subsequent 16 bits indicate the base filter Id; this corresponds to the first number ('9') in the example '9:P2' - The range 0x04000001 .. 0x0400FFFF (67108865..67174399) indicates a filter managed by a VSD controller. In this case the last 16 bits indicate the ID of the VSD filter.

TEXTUAL-CONVENTION

The identification number of a filter. Any value greater than 0x0000FFFF (65535) indicates a filter that was dynamically created (auto-generated) by the system and as such cannot be used as part of any SNMP SET operation. - The range 0x00000001 .. 0x0000FFFF (1 .. 65535) indicates a regular configuration originated filter. - The range 0x04000001 .. 0x0400FFFF (67108865 .. 67174399) indicates a filter managed by a VSD controller. In this case the last 16 bits indicate the ID of the VSD filter. - The value 0 indicates an invalid filter-id (e.g. no filter applied on a particular endpoint).

TEXTUAL-CONVENTION

The identification number of a DHCP filter.

TEXTUAL-CONVENTION

TEXTUAL-CONVENTION

Action to take on DHCP host creation when the filter entry matches. When set to none(1), host creation proceeds as normal. When set to bypass-host-creation(2), host creation is bypassed. When set to drop(3), the DHCP message is dropped.

TEXTUAL-CONVENTION

Match condition for a DHCP option in a DHCP filter entry When set to present(1) the related DHCP option must be present, when set to absent(2) the related DHCP option must be absent. When set to string(3) the option must (partially) match a specified ASCII string, setting string-exact(4) requires an exact match, setting string-invert(5) requires the option not to (partially) match, setting string-exact-invert(6) requires the option not to match exact. Setting hex(7), hex-exact(8), hex-invert(9) or hex-exact-invert(10) will use a hex octet string for the matching.

TEXTUAL-CONVENTION

Defines size of block used for filter entries insertion.

TEXTUAL-CONVENTION

Uniquely identifies an entry in a policy or filter table. To facilitate insertion of entries in the tables, we recommend assigning entry IDs by 10s: 10, 20, 30, etc.

TEXTUAL-CONVENTION

Uniquely identifies an entry in a policy or filter table. To facilitate insertion of entries in the tables, we recommend assigning entry IDs by 10s: 10, 20, 30, etc. The value 0, means that the object does not refer to a filter entry at this time.

TEXTUAL-CONVENTION

Action to take on a packet: - drop (1): packets matching the filter entry are dropped. - forward (2): packets matching the filter entry are forwarded. - httpRedirect(4): packets matching the filter entry are redirected. - nat (5): packets matching the filter entry are forwarded to the NAT function in the system. - reassemble (6): packets matching the filter entry are forwarded to the packet REASSEMBLE function in the system. - gtpLclBrkout(7): packets matching the filter entry are broken out locally from a GTP tunnel (and thereby bypass the mobile packet core). For packets that are not sent in the context of a GTP tunnel, this action is equivalent to 'forward'. - forwardEsiL2(8): packets matching the filter entry are forwarded to ESI identified first appliance in Nuage service chain using EVPN-resolved VXLAN tunnel in the specified VPLS service. - forwardEsiL3(9): packets matching the filter entry are forwarded to ESI/SF-IP identified first appliance in Nuage service chain using EVPN-resolved VXLAN tunnel over the configured VAS interface in the specified VPRN service. - unrecognized(11): Tables tMacFilterParamsTable, tIPFilterParamsTable, tIPv6FilterParamsTable and their augment tables can only be used to configure actions which were available before introducing tMacFltrEntryActionTable and tIPvXFltrEntryActionTable. All actions (including action related functionality) can be configured via tables tMacFltrEntryActionTable and tIPvXFltrEntryActionTable. The value 'unrecognized' indicates that the currently configured action was added after introduction of tMacFltrEntryActionTable and tIPvXFltrEntryActionTable and can't be interpreted in the tables tMacFilterParamsTable, tIPFilterParamsTable, tIPv6FilterParamsTable and their augment tables.

TEXTUAL-CONVENTION

Action to take on a packet: - drop (1): packets matching the filter entry are dropped. - forward (2): packets matching the filter entry are forwarded. - default (3): packets matching the filter entry get the applicable default behavior. Note: the value 'default' is currently not supported. - httpRedirect(4): packets matching the filter entry are redirected. - nat (5): packets matching the filter entry are forwarded to the NAT function in the system. - reassemble (6): packets matching the filter entry are forwarded to the packet REASSEMBLE function in the system. - gtpLclBrkout(7): packets matching the filter entry are broken out locally from a GTP tunnel (and thereby bypass the mobile packet core). For packets that are not sent in the context of a GTP tunnel, this action is equivalent to 'forward'. - forwardEsiL2(8): packets matching the filter entry are forwarded to ESI identified first appliance in Nuage service chain using EVPN-resolved VXLAN tunnel in the specified VPLS service. - forwardEsiL3(9): packets matching the filter entry are forwarded to ESI/SF-IP identified first appliance in Nuage service chain using EVPN-resolved VXLAN tunnel over the configured VAS interface in the specified VPRN service. - unrecognized(11): Tables tMacFilterParamsTable, tIPFilterParamsTable, tIPv6FilterParamsTable and their augment tables can only be used to configure actions which were available before introducing tMacFltrEntryActionTable and tIPvXFltrEntryActionTable. All actions (including action related functionality) can be configured via tables tMacFltrEntryActionTable and tIPvXFltrEntryActionTable. The value 'unrecognized' indicates that the currently configured action was added after introduction of tMacFltrEntryActionTable and tIPvXFltrEntryActionTable and can't be interpreted in the tables tMacFilterParamsTable, tIPFilterParamsTable, tIPv6FilterParamsTable and their augment tables. - ignoreMatch(30): Match criteria are skipped.

TEXTUAL-CONVENTION

Filter action downloaded to IOM: - none (1): No filter entry action is downloaded to IOM. Entry is inactive or filter is not applied. - primary (2): Primary filter entry action is downloaded to IOM. - secondary (3): Secondary filter entry action is downloaded to IOM. - forward (4): Neither primary nor secondary action is downloaded to IOM. Action forward is downloaded to IOM. - drop (5): Neither primary nor secondary action is downloaded to IOM. Action drop is downloaded to IOM. - notDisplayed (6): Field is not supported for configured action.

TEXTUAL-CONVENTION

disable - 0: policy based routing has no effect when applied on egress enable - 1: egress policy based routing is allowed and default load-balancing based on hash of source/destination address of the packet is applied enableWithL4LB - 2: egress policy based routing is allowed and l4-load-balancing is applied (if available include TCP/UDP port in hash.

TEXTUAL-CONVENTION

Insertion offset of entries of an embedded filter into an embedding filter. An entry at position x in the embedded filter is inserted at position x + offset in the embedding filter.

TEXTUAL-CONVENTION

The textual convention TFilterEntryActionId specifies the unique identifier and also the priority of the action within the filter entry.

TEXTUAL-CONVENTION

A limiting rate in kilobits per second for traffic matching the filter entry. The value -1 means max rate.

TEXTUAL-CONVENTION

Ethernet Segment Identifier (ESI) as defined in IETF draft BGP MPLS Based Ethernet VPN. ESI is a unique non-zero identifier that identifies an Ethernet Segment. ESI is encoded as a ten octets integer in line format with the most significant octet sent first. The following two ESI values are reserved: - ESI 0 denotes a single-homed CE. - ESI 0xFF repeated 10 times is known as MAX-ESI. In a network with managed and not-managed CEs, the ESI has the following format: +---+---+---+---+---+---+---+---+---+---+ | T | ESI Value | +---+---+---+---+---+---+---+---+---+---+ Where: T (ESI Type) is a 1-octet field (most significant octet) that specifies the format of the remaining nine octets (ESI Value). ESI type can be one of the values 0x00-0x05.

TEXTUAL-CONVENTION

The identification number of a flowspec group. 65535 indicates an invalid group id (when used in embedding it means embed rules from all groups)

TEXTUAL-CONVENTION

The identification number of a filter. 0 indicates an invalid filter-id.

TEXTUAL-CONVENTION

The TFilterPacketLength textual convention is used to specify the total length value of a packet

TEXTUAL-CONVENTION

Determines the location where filtered packets are logged.

TEXTUAL-CONVENTION

Uniquely identifies an entry in the filter log table. 0 indicates an invalid log-id.

TEXTUAL-CONVENTION

Indicates the field on which log summarization will be done. - when set to srcAddr, received log packets are summarized based on the src ip/mac-addr - when set to dstAddr, received log packets are summarized based on the dst ip/mac-addr

TEXTUAL-CONVENTION

The TFilterPacketLength textual convention is used to specify the 'Total Length' value of packet's IPv4 header or the 'Payload Length' value of packet's IPv6 header.

TEXTUAL-CONVENTION

The textual convention TFilterPbrDownActionOvr specifies an override of default PBR down action: - none (0): default PBR down action is applied to packets matching the filter entry. Default PBR down action is either drop or forward based on PBR action type. - drop (1): packets matching the filter entry are dropped. - forward (2): packets matching the filter entry are forwarded. - filterDefaultAction (3): packets matching the filter entry are handled according to filter default action configured using tIPFilterDefaultAction for IP filter, tIPv6FilterDefaultAction for IPv6 filter and tMacFilterDefaultAction for MAC filter.

TEXTUAL-CONVENTION

Status of PBR target : - unknown (0): Status of PBR target is not tracked - doesNotExist (1): The system does not know the PBR target. - up (2): PBR target is known by the system and can be used for forwarding the traffic. - down (3): PBR target is known by the system but can't be used for forwarding the traffic. - routerSpecific (4): PBR target status depends on service where filter is applied.

TEXTUAL-CONVENTION

This textual convention specifies how the destinations in filter redirect policy binding are combined to form the operational state of the whole binding.

TEXTUAL-CONVENTION

This textual convention determines some aspects of an item's behavior regarding creation and use, unused entry garbage collection, and automated promulgation by Element Management System to other systems in the service domain. TFilterScope is an extension of the textual convention TItemScope. exclusive: When the scope of an item is defined as exclusive, the item can only be applied once, for example to a single SAP. Attempting to assign the policy to a second SAP is not allowed and will result in an error. If the item is removed from the exclusive SAP, it will become available for assignment to another exclusive SAP. A non-applied exclusive scope policy is a candidate to be removed from the system by a TBD garbage collection command. The system default policies cannot be put into the exclusive scope. An error will be generated if scope exclusive is executed in any policies with a policy-id equal to 1. template: When the scope of an item is defined as template, the item can be applied any number of times. Policies with template scope will not be considered for deletion by a TBD garbage collection command; all items of scope 'template' must be deleted explicitly. The system default policies will always be scope template. An error will occur if a policy-id 1 is attempted to be set to scope exclusive. embedded: When the scope of a filter is defined as embedded, this indicates that the filter may be embedded in other non-embedded filters. An embedded filter may not be applied anywhere in the system. Attempting to set scope to embedded for a filter which is already applied will be rejected by the system. system: When the scope of a filter policy is defined as system, the filter policy can be used as a common system filter policy only. The policy cannot be applied directly anywhere in the system. In order to activate the policy it must be configured as the active system filter policy in tFilterSystemFilterTable. All other 'exclusive' and 'template' IP / IPv6 filter policies may be chained to the active system policy by setting the tIPFilterChainToSystemFilter or tIPv6FilterChainToSystemFilter object to 'true(1)'. When an IP / IPv6 filter policy is chained to the system filter policy, system filter policy's rules are executed first before any rules of the activating filter policy are executed. The scope of a filter policy can be set to/from this value only when the policy does not contain any entry.

TEXTUAL-CONVENTION

Owner of a range of filter entries related to subscribers in an existing filter

TEXTUAL-CONVENTION

The TFilterTTL textual convention is used to specify a Time To Live (IPv4) or Hop Limit (IPv6) value.

TEXTUAL-CONVENTION

Type of filter.

TEXTUAL-CONVENTION

Application capable of inserting filter entries into an existing filter that supports regrouping of inserted entries

TEXTUAL-CONVENTION

This textual convention specifies how the source port and destination port filter objects are combined to form the filter match criterion. - If the selector takes the value and-port(0) then the source port and destination port objects (if set) are combined into 1 filter condition that fires if both conditions are met (i.e. a logical and-operation of both is done). If one of them is not set (default values) then only the other one is taken into account for the match condition. - If the selector takes the value or-port(1) then the source port objects are used as match condition for either source port or destination port (i.e. a logical or-operation is done). In this case, non-default values must be set for the source port objects. In this case the destination port objects are (silently) copied from the source port objects by the system; any other values set by the user are overwritten by the system.

TEXTUAL-CONVENTION

The type TFltrPrefixListType enumerates all possible prefix list types.

TEXTUAL-CONVENTION

when set to off, the item is not matched. when set to false, packets without the item match the filter entry. when set to true, packets with the item match the filter entry. when set to first-only, packets with first fragment match the filter entry. when set to non-first-only, packets with non-first fragment match the filter entry.

TEXTUAL-CONVENTION

The identification number of an IP filter.

TEXTUAL-CONVENTION

Action to take on a packet: - drop (1): A packet matching the entry will be dropped. - forward (2): A packet matching the entry will be forwarded using regular routing. - httpRedirect (4): An HTTP GET packet matching the entry is forwarded to CPM for HTTP captive portal processing. - nat (5): A packet matching the entry will be forwarded to NAT. - reassemble (6): Packets matching the entry are forwarded to the packet REASSEMBLE function in the system. - gtpLclBrkout (7): A packet matching the entry is broken out locally from a GTP tunnel (and thereby bypass the mobile packet core). For packets that are not sent in the context of a GTP tunnel, this action is equivalent to forward. - forwardEsiL2 (8): A packet matching the entry will be forwarded to ESI identified first appliance in Nuage service chain using EVPN-resolved VXLAN tunnel in the specified VPLS service. - forwardEsiL3 (9): A packet matching the entry will be forwarded to ESI/SF-IP identified first appliance in Nuage service chain using EVPN-resolved VXLAN tunnel over the configured VAS interface in the specified VPRN service. - ofPacketIn (10): Packets are sent to controller configured for this H-OFS instance on a dedicated packet-in channel part of the main or auxiliary connection. - dropTtl (12): A packet matching the entry will be dropped only if 'Time-to-live' field of packet's IPv4 header or 'Hop-Limit' field of packet's IPv6 header meets the configured condition. - dropPktLen (13): A packet matching the entry will be dropped only if 'Total Length' field of packet's IPv4 header or 'Payload Length' field of packet's IPv6 header field meets the configured condition. - forwardRtr (14): A packet matching the entry will be forwarded in the configured routing context. - forwardNextHop (15): A packet matching the entry will be forwarded in the routing context of the incoming interface using direct or indirect IP address in the routing lookup. - forwardNextHopRtr (16): A packet matching the entry will be forwarded in the configured routing context using direct or indirect IP address in the routing lookup. - forwardNHInterface (17): A packet matching the entry will be forwarded using the configured local interface. - forwardLsp (18): A packet matching the entry will be forwarded using the specified LSP. - forwardSdp (19): A packet matching the entry will be forwarded using the configured SDP. - forwardSap (20): A packet matching the entry will be forwarded using the configured SAP. - forwardRPlcy (21): A packet matching the entry will be forwarded using forward next-hop or forward next-hop router and the IP address of destination selected by the configured redirect policy. If no destination is selected packets are subject to action forward. - rateLimit (22): Traffic matching the entry will be limited to the value specified by the object tIPvXFltrEntryActRateLimit. - tcpMssAdjust (23): The value of TCP Maximum Segment Size (MSS) option of packets matching the entry will be set to the value specified by TIMETRA-VRTR-MIB.mib::tmnxVrtrMssAdjSegmentSize if the value of the option exceeds that value or the option is not present at all. - remarkDscp (24): DSCP value of packets matching the entry will be remarked. - rateLimitPktLen (25): Packet rate of packets matching the entry and having value of 'Total Length' field of packet's IPv4 header or value of 'Payload Length' field of packet's IPv6 header meeting the configured condition is limited to value specified by tIPvXFltrEntryActRateLimit. - rateLimitTtl (26): Packet rate of packets matching the entry and having value of 'Time-to-live' field of packet's IPv4 header or value of 'Hop-Limit' field of packet's IPv6 header meeting the configured condition is limited to value specified by tIPvXFltrEntryActRateLimit. - dropExtractedTraffic (27): Traffic extracted to CPM will be dropped. - forwardVprnTarget (28): A packet matching the filter entry will be forwarded using specified tunnel. - forwardBondingConnection (29):In a bonding context indicates the packet should be forwarded over the given connection if that connection is available. Outside a bonding context this is equivalent to an unqualified forward action. - ignoreMatch (30): Match criteria are skipped. - forwardGreTunnel (31):A packet matching the entry will be encapsulated in GRE an transported to a locations defined in GRE tunnel template. - dropPattern (32):A packet matching the entry and containing the specified pattern will be dropped. - rateLimitPattern (33):Packet rate of packets matching the entry and containing the specified pattern is limited to value specified by tIPvXFltrEntryActRateLimit. - forwardPattern (34):A packet matching the entry and containing the specified pattern will be forwarded. - forwardMplsPlcyEndpt (35): A packet matching the entry will be forwarded using a tunnel associated with the MPLS forawarding policy endpoint. - forwardSrtePlcyEndptColor (36): A packet matching the entry will be forwarded using a tunnel associated with the SR-TE policy endpoint and color.

TEXTUAL-CONVENTION

Action to take on a packet: - none (0) : This value indicates that no action is specified. - remarkDscp (24): DSCP value of packets will be remarked.

TEXTUAL-CONVENTION

Specifies the set of available match criteria for a filter policy. - normal (0): Allows all match criteria except of: - Source MAC, Packet length. - srcMac (1): Allows matching Source MAC and all match criteria for type normal except of: - Source IP, DSCP and all IP Options in IPv4 filters. - Source IP in IPv6 filters. - pktLen (2): Allows matching Packet length and all match criteria for type normal except of: - DSCP and IP Options in IPv4 filters. - Flow Label in IPv6 filters.

TEXTUAL-CONVENTION

when set to off, the item is not matched. when set to false, packets without the item match the filter. when set to true, packets with the item match the filter.

TEXTUAL-CONVENTION

Uniquely identifies an entry in a policy or filter table. To facilitate insertion of entries in the tables, we recommend assigning entry IDs by 10s: 10, 20, 30, etc.

TEXTUAL-CONVENTION

Action to take on a packet matching the filter entry: - drop (1) : A packet matching the entry will be dropped. - forward (2) : A packet matching the entry will be forwarded using regular routing. - httpRedirect (4): An HTTP GET packet matching the entry is forwarded to CPM for HTTP captive portal processing. - forwardEsiL2 (8): A packet matching the entry will be forwarded to ESI identified first appliance in Nuage service chain using EVPN-resolved VXLAN tunnel in the specified VPLS service. - forwardSdp (19): A packet matching the entry will be forwarded using the configured SDP. - forwardSap (20): A packet matching the entry will be forwarded using the configured SAP. - rateLimit (22): Traffic matching the entry will be limited to the value specified by the object tIPvXFltrEntryActRateLimit. - ignoreMatch (30): Match criteria are skipped.

TEXTUAL-CONVENTION

The textual convention TTimeRangeState is used to indicate the state of an object that is controlled by a time range. - timeRangeNotApplic: no time range is applicable for this entry. - timeRangeNotActive: A time range is defined but is not active at this moment. - timeRangeActive. A time range is defined, and is activated successfully. - timeRangeActiveDownloadFailed: A time range is defined and is activated, but the corresponding object could not be installed due to resource problems.

TEXTUAL-CONVENTION

The identification number of a filter managed by a VSD controller. The value of the upper 16 bits is always equal to 0x0400. The value of the lower 16 bits corresponds to the last segment of the name used for the filter in CLI (_tmnx_vsd_<lower_16_bits>).

TEXTUAL-CONVENTION

The TmnxEmbeddedFltrAdminState data type is an enumerated integer that describes the current administrative state of a filter embedding request.

TEXTUAL-CONVENTION

The TmnxEmbeddedFltrOperState data type is an enumerated integer that describes the current operational state of a filter embedding request.

TEXTUAL-CONVENTION

The TmnxFilterApplyPathSource data type is an enumerated integer that describes the source of the apply-path imported prefixes

TEXTUAL-CONVENTION

The TmnxFilterRPlcyTestLastAction textual convention is used to indicate the last impact of a test assigned to a destination of a redirect policy on an operational state of the destination. Value 'enable' indicates the operational state of the destination has been set to 'inService'. Value 'disable' indicates the operational state of the destination has been set to 'outOfService'. Value 'none' indicates the operational state of the destination has not been changed yet.

TEXTUAL-CONVENTION

The TmnxFilterRPlcyTestRespAction textual convention is used to indicate the action of a test assigned to a destination of a redirect policy on a operational priority of the destination. Value 'increase' indicates that if the response passes the test the operational priority of the destination will be increased. Value 'decrease' indicates that if the response passes the test the operational priority of the destination will be decreased. Value 'disable' indicates the test wont have impact on the operational priority of the destination.

TEXTUAL-CONVENTION

The TmnxFltrEmbeddedEntryState data type is an enumerated integer that describes the current operational state of an embedded filter entry.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

Contains a List of all ip filters configured on this system.

OBJECT-TYPE

Information about a particular IP Filter entry. Entries are created/deleted by user. Entries have a presumed StorageType of nonVolatile.

OBJECT-TYPE

The value of the object tIPFilterId uniquely identifies an ip filter. User-configured filters have values between (1..65535). Other values are reserved for filters that are created (auto-generated) by the system. Refer to the description of the textual convention TAnyFilterID for more details.

OBJECT-TYPE

This object allows entries to be created and deleted in the tIPFilterTable.

OBJECT-TYPE

This object specifies the scope of this filter definition.

OBJECT-TYPE

User-provided description for this filter.

OBJECT-TYPE

The action to take for packets that do not match any filter entries. The only allowed values for this field are drop(1) and forward(2).

OBJECT-TYPE

The value of tIPFilterRadiusInsertPt specifies at what place the host specific filter entries received from Radius will be inserted in the filter. The area defined here will be dedicated to those entries, no other entries will be allowed. The value 0 means that no Radius provided host specific filter entries can be inserted in the filter. If tIPFilterRadiusInsertSize is set to 0, then this object will be put to 0 as well. Any change attempts will result in error.

OBJECT-TYPE

The value of tIPFilterRadiusInsertSize specifies how many host specific filter entries received from Radius for subscriber hosts can be inserted in the filter. If tIPFilterRadiusInsertPt is set to 0, then this object will be put to 0 as well. Any change attempts will result in error.

OBJECT-TYPE

The value of tIPFilterCreditCntrlInsertPt specifies at what place the filter entries received from Credit Control for a particular subscriber host will be inserted in the filter. The area defined here will be dedicated to those entries, no other entries will be allowed. The value 0 means that no Credit Control provided filter entries can be inserted in the filter. If tIPFilterCreditCntrlInsertSize is set to 0, then this object will be put to 0 as well. Any change attempts will result in error.

OBJECT-TYPE

The value of tIPFilterCreditCntrlInsertSize specifies how many filter entries received from Credit Control can be inserted in the filter. If tIPFilterCreditCntrlInsertPt is set to 0, then this object will be put to 0 as well. Any change attempts will result in error

OBJECT-TYPE

The value of the object tIPFilterSubInsertHighWmark specifies the utilization of the filter ranges for filter entry insertion, at which a table full alarm will be raised by the agent. The value 0 indicates that no alarm will be generated.

OBJECT-TYPE

The value of the object tIPFilterSubInsertLowWmark specifies the utilization of the filter ranges for filter entry insertion, at which a table full alarm will be cleared by the agent.

OBJECT-TYPE

The value of the object tIpFilterCreditCntrlNbrInsertd indicates how many filter entries are currently inserted in the filter on request of credit control.

OBJECT-TYPE

The value of the object tIpFilterRadiusNbrInsertd indicates how many host specific filter entries are currently inserted in the filter on request of RADIUS.

OBJECT-TYPE

The value of tIpFilterName specifies the name to associate with this filter.

OBJECT-TYPE

The value of tIPFilterHostSharedInsertPt specifies at what place the filter entries received from Radius that are shared between several hosts (host common rules) will be inserted in the filter. The area defined here will be dedicated to those entries, no other entries will be allowed. The value 0 means that no Radius provided host common filter entries can be inserted in the filter. If tIPFilterHostSharedInsertSize is set to 0, then this object will be put to 0 as well. Any change attempts will result in error.

OBJECT-TYPE

The value of tIPFilterHostSharedInsertSize specifies how many host common filter entries received from Radius for subscriber hosts can be inserted in the filter. If tIPFilterHostSharedInsertPt is set to 0, then this object will be put to 0 as well. Any change attempts will result in error.

OBJECT-TYPE

The value of the object tIpFilterHostSharedNbrInsertd indicates how many Radius Shared Filter rules are inserted in the filter.

OBJECT-TYPE

The value of the object tIPFilterHostSharedHighWmark specifies the number of Radius Shared Filters that can be dynamically created in the system before an high watermark notification is generated by the system. The value -1 specifies that no notifications are sent. If any of the watermarks (high or low) is set to -1, both watermarks will be set to -1 by the system.

OBJECT-TYPE

The value of the object tIPFilterHostSharedLowWmark specifies the number of Radius Shared Filters that are still dynamically created in the system before an high watermark notification is cleared by the system. The value -1 specifies that no notifications are sent. If any of the watermarks (high or low) is set to -1, both watermarks will be set to -1 by the system.

OBJECT-TYPE

The value of the object tIPFilterNbrHostSharedFltrs indicates how many filters are currently created by Radius or Diameter based on this filter. (Both host shared or flow-rule filters.)

OBJECT-TYPE

The value of tIPFilterSharedPccRuleInsrtPt specifies at what place the flow-rule filter entries that are received from Diameter and that are shared across several hosts will be inserted in the filter. The range defined here will be reserved for those entries; no other entries will be allowed in this range. The value 0 means that no flow-rule filter entries can be inserted in the filter by Diameter. If tIPFilterSharedPccRuleInsrtSize is set to 0 then tIPFilterSharedPccRuleInsrtPt is also set to 0 by the system. Note that the range reserved for shared flow-rule entries must not overlap with that of either tIPFilterRadiusInsertPt/tIPFilterRadiusInsertSize, tIPFilterCreditCntrlInsertPt/tIPFilterCreditCntrlInsertSize, or tIPFilterHostSharedInsertPt/tIPFilterHostSharedInsertSize

OBJECT-TYPE

The value of tIPFilterSharedPccRuleInsrtSize specifies how many flow-rule filter entries that are received from Diameter and that are shared across several hosts can be inserted in the filter. The range defined here will be reserved for those entries; no other entries will be allowed in this range. The value 0 means that no flow-rule filter entries can be inserted in the filter by Diameter. If tIPFilterSharedPccRuleInsrtPt is set to 0 then tIPFilterSharedPccRuleInsrtSize is also set to 0 by the system. Note that the range reserved for shared flow-rule entries must not overlap with that of either tIPFilterRadiusInsertPt/tIPFilterRadiusInsertSize, tIPFilterCreditCntrlInsertPt/tIPFilterCreditCntrlInsertSize, or tIPFilterHostSharedInsertPt/tIPFilterHostSharedInsertSize

OBJECT-TYPE

The value of the object tIPFilterSharedPccRuleNbrInsrtd indicates how many flow-rule filter entries received from Diameter have been inserted in this filter

OBJECT-TYPE

The value of the object tIPFilterChainToSystemFilter specifies whether this filter policy is chained to the active IP system filter policy. The active IP system filter policy is defined as a row in tFilterSystemFilterTable that have the value of the object tFilterSystemFilterType set to 'fltrtypeselIp(1)'. The value 'true(1)' means this filter policy is chained to the active IP system filter policy. The system filter policy's rules are executed first before any rules of this filter policy are executed. The value of this object can be set to 'true(1)' only when the scope of this policy (value of the object tIPFilterScope) is 'exclusive(1)' or 'template(2)'. The value 'false(2)' means this filter policy is not chained to the active IP system filter policy.

OBJECT-TYPE

The value of the object tIPFilterType specifies the type of IP filter.

OBJECT-TYPE

A table of all IP filter match entries for all IP filters.

OBJECT-TYPE

Information about a particular IP Filter entry. Every IP Filter can have zero or more IP Filter match entries. A filter entry with no match criteria set will match every packet, and the entry action will be taken. Entries are created/deleted by user. Additional parameters can be found in tIPFilterParamsExtTable. There is no StorageType object, entries have a presumed StorageType of nonVolatile.

OBJECT-TYPE

This is the secondary index for the entry. Every ip filter can have multiple entries, therefore every ip filter entry is identified by the tIPFilterId and tIPFilterParamsIndex.

OBJECT-TYPE

This object allows entries to be created and deleted in the tIPFilterParamsTable.

OBJECT-TYPE

This object specifies the log to use for packets that match this entry. The value zero indicates that logging is disabled.

OBJECT-TYPE

User-provided description for this filter entry.

OBJECT-TYPE

The action to take for packets that match this filter entry. The value default(3) specifies this entry to inherit the behavior defined as the default for the filter. Setting the values 'forwardEsiL2' and 'forwardEsiL3' explicitly is ignored by the system. The values 'forwardEsiL2'(8) and 'forwardEsiL3'(9) can be set only implicitly by specifying non default values of objects specifying parameters for these actions. In such case the value of tIPFilterParamsAction will be set to 'forwardEsiL2'(8) or 'forwardEsiL3'(9) automatically by system. The object tIPFilterParamsAction supports only subset of filter actions. The object tIPvXFltrEntryActAction supports all actions. It's recommended to use tIPvXFltrEntryActAction instead of tIPFilterParamsAction.

OBJECT-TYPE

The IP address of the nexthop to which the packet should be forwarded if it hits this filter entry. The action of this entry should be 'forward' in such a case. Note that the value of tIPFilterParamsForwardNH is silently cleared by the system if tIPFilterParamsAction is set to value other than 'forward'(2), or any object related to 'forward' other than tIPFilterParamsForwardNH, tIPFilterParamsForwardNHIndirect or tIPFilterParamsFwdRtrId is set.

OBJECT-TYPE

tIPFilterParamsForwardNHIndirect specifies if the nexthop is directly/ indirectly reachable. Note that the value of tIPFilterParamsForwardNHIndirect is silently cleared by the system if tIPFilterParamsAction is set to value other than 'forward'(2), or any object related to 'forward' other than tIPFilterParamsForwardNH, tIPFilterParamsForwardNHIndirect or tIPFilterParamsFwdRtrId is set.

OBJECT-TYPE

The DSCP value that should be remarked in case a packet hits this filter entry.

OBJECT-TYPE

tIPFilterParamsRemarkDSCPMask specifies the care bits while remarking with the DSCP value.

OBJECT-TYPE

tIPFilterParamsRemarkDot1p specifies the Dot1p value that needs to be remarked on the packet if it hits this filter entry.

OBJECT-TYPE

IP address to match the source IP address of the packet.

OBJECT-TYPE

If different from 0, the object tIPFilterParamsSourceIpMask specifies the IP Mask value for this policy IP Filter entry. The mask is ANDed with the received source IP address to match the tIPFilterParamsSourceIpAddr. If the value of tIPFilterParamsSourceIpMask is 0, and the value of tIPFilterParamsSrcIpFullMask is non zero then the value of tIPFilterParamsSrcIpFullMask is used as mask. If the value of tIPFilterParamsSourceIpMask is non zero, it will be equal to the mask expressed the object tIPFilterParamsSrcIpFullMask. If both tIPFilterParamsSourceIpMask and tIPFilterParamsSrcIpFullMask are set to 0, no matching is done on the source IP address. If a value is specified for this object, then the value of the object tIPFilterParamsSrcIpFullMask will be set to reflect this same mask.

OBJECT-TYPE

IP address to match the destination IP address of the packet.

OBJECT-TYPE

If different from 0, the object tIPFilterParamsDestinationIpMask specifies the IP Mask value for this policy IP Filter entry. The mask is ANDed with the received Destination IP address to match the tIPFilterParamsDestinationIpAddr. If the value of tIPFilterParamsDestinationIpMask is 0, and the value of tIPFilterParamsDestIpFullMask is non zero then the value of tIPFilterParamsDestIpFullMask is used as mask. If the value of tIPFilterParamsDestinationIpMask is non zero, it will be equal to the mask expressed the object tIPFilterParamsDestIpFullMask. If both tIPFilterParamsDestinationIpMask and tIPFilterParamsDestIpFullMask are set to 0, no matching is done on the Destination IP address. If a value is specified for this object, then the value of the object tIPFilterParamsDestIpFullMask will be set to reflect this same mask.

OBJECT-TYPE

IP protocol to match. Set to -1 to disable matching IP protocol.

OBJECT-TYPE

TCP/UDP port value1. The value of this object is used as per the description for tIPFilterParamsSourcePortOperator.

OBJECT-TYPE

TCP/UDP port value2. The value of this object is used as per the description for tIPFilterParamsSourcePortOperator.

OBJECT-TYPE

The operator specifies the manner in which tIPFilterParamsSourcePortValue1 and tIPFilterParamsSourcePortValue2 are to be used. The value of these latter 2 objects and tIPFilterParamsSourcePortOperator is used as described in TTcpUdpPortOperator.

OBJECT-TYPE

TCP/UDP port value1. The value of this object is used as per the description for tIPFilterParamsDestPortOperator.

OBJECT-TYPE

TCP/UDP port value2. The value of this object is used as per the description for tIPFilterParamsDestPortOperator.

OBJECT-TYPE

The operator specifies the manner in which tIPFilterParamsDestPortValue1 and tIPFilterParamsDestPortValue2 are to be used. The value of these latter 2 objects and tIPFilterParamsDestPortOperator is used as described in TTcpUdpPortOperator.

OBJECT-TYPE

DSCP to be matched on the packet.

OBJECT-TYPE

If enabled, this object matches fragmented/unfragmented packets as per the value of the object.

OBJECT-TYPE

If enabled, this object matches packets if they have options present or not as per the value of the object.

OBJECT-TYPE

The value of the specific IP option to match.

OBJECT-TYPE

Mask is ANDed with the IP option before being compared to tIPFilterParamsIpOptionValue.

OBJECT-TYPE

If enabled, matches multiple options as per the value of the object.

OBJECT-TYPE

If Enabled, matches a TCP Syn as per value of the object.

OBJECT-TYPE

If Enabled, matches a TCP Ack as per value of the object.

OBJECT-TYPE

ICMP code to be matched. The value -1 means ICMP code matching is not enabled.

OBJECT-TYPE

ICMP type to be matched. The value -1 means ICMP type matching is not enabled.

OBJECT-TYPE

When tIPFilterParamsCflowdSample has a value of 'true', Cflowd sampling and analysis is performed on those packet streams where this filter has been applied. Only packets matching this IP filter entry are subjected to Cflowd sampling and analysis. A Cflowd profile controls the sampling and analysis of data flows through the router.

OBJECT-TYPE

When tIPFilterParamsCflowdIfSample has a value of 'true', Cflowd sampling and analysis is performed on those packet streams where this filter has been applied. Only packets matching this IP filter entry are subjected to Cflowd sampling and analysis. A Cflowd profile controls the sampling and analysis of data flows through the router.

OBJECT-TYPE

The interface name for the nexthop to which the packet should be forwarded if it hits this filter entry. The action of this entry should be 'forward' in such a case. Note that the value of tIPFilterParamsForwardNHInterface is silently cleared by the system if tIPFilterParamsAction is set to value other than 'forward'(2) or any object related to 'forward' other than this one is set.

OBJECT-TYPE

This object indicates the number of times an ingress packet matched this entry.

OBJECT-TYPE

This object indicates the number of times an egress packet matched this entry.

OBJECT-TYPE

tIPFilterParamsLogInstantiated indicates if the filter log for this filter entry has been instantiated or not.

OBJECT-TYPE

tIPFilterParamsForwardRedPlcy specifies the redirect policy to be used to determine the nexthop. Note that the value of tIPFilterParamsForwardRedPlcy is silently cleared by the system if tIPFilterParamsAction is set to value other than 'forward'(2) or any object related to 'forward' other than this one is set.

OBJECT-TYPE

tIPFilterParamsActiveDest indicates the IP address of the active destination for this IP filter. A value of 0 indicates that there is currently no active destination.

OBJECT-TYPE

tIPFilterParamsFwdSvcId indicates the service id of the destination for this IP filter entry. A value of 0 indicates that there is currently no active SAP or SDP destination.

OBJECT-TYPE

tIPFilterParamsFwdSapPortId specifies the sap port identity of the destination for this IP filter entry. A value of 0 indicates that there is currently no SAP destination defined. A value different from 0 can only be specified if the value of the tIPFilterParamsAction object of this entry is 'forward'. In addition a non-zero value can only be given if the object tIPFilterParamsFwdSdpBind has a zero value. Note that the value of tIPFilterParamsFwdSapPortId is silently cleared by the system if tIPFilterParamsAction is set to value other than 'forward'(2) or any object related to 'forward' other than tIPFilterParamsFwdSapPortId, tIPFilterParamsFwdSapEncapVal is set.

OBJECT-TYPE

tIPFilterParamsFwdSapEncapVal specifies the sap port encap value of the destination SAP for this IP filter entry. A value different from 0 can only be specified if the value of the tIPFilterParamsAction object of this entry is 'forward'. In addition a non-zero value can only be given if the object tIPFilterParamsFwdSdpBind has a zero value. A value of 0 indicates that either 1) the sap encapsulation value is not specified when tIPFilterParamsFwdSapPortId and tIPFilterParamsFwdSvcId have valid values; or 2) that there is no SAP destination. Note that the value of tIPFilterParamsFwdSapEncapVal is silently cleared by the system if tIPFilterParamsAction is set to value other than 'forward'(2) or any object related to 'forward' other than tIPFilterParamsFwdSapPortId or tIPFilterParamsFwdSapEncapVal is set.

OBJECT-TYPE

tIPFilterParamsFwdSdpBind specifies the sdp bind identity of the destination for this IP filter entry. A value of 0 indicates that there is currently no SDP binding defined. A value different from 0 can only be specified if the value of the tIPFilterParamsAction object of this entry is 'forward'. In addition a non-zero value can only be given if the objects tIPFilterParamsFwdSapPortId and tIPFilterParamsFwdSapEncapVal have a zero value. Note that the value of tIPFilterParamsFwdSdpBind is silently cleared by the system if tIPFilterParamsAction is set to value other than 'forward'(2) or any object related to 'forward' other than this one is set.

OBJECT-TYPE

tIPFilterParamsTimeRangeName specifies the tmnxTimeRangeEntry to be associated with this filter entry. A value for this object can only be specified during row creation, and cannot be altered later on. Also, a value is accepted only if the tmnxTimeRangeEntry is defined in the TIMETRA-SCHEDULER-MIB::tmnxTimeRangeTable.tTimeRangeName. This object is obsoleted in release 14.0.

OBJECT-TYPE

tIPFilterParamsTimeRangeState indicates whether or not the entry is currently in effect. - timeRangeNotApplic: no time range is applicable for this entry. - timeRangeNotActive: A time range is defined in tIPFilterParamsTimeRangeName, but is not active at this moment. Consequently the filter entry is not installed. - timeRangeActive. A time range is defined in tIPFilterParamsTimeRangeName, and is activated successfully. - timeRangeActiveDownloadFailed: A time range is defined in tIPFilterParamsTimeRangeName, and is activated, but the corresponding filter entry could not be installed due to resource problems. This object is obsoleted in release 14.0.

OBJECT-TYPE

The value of tIPFilterParamsRedirectURL specifies the URL to redirect to, when the value of tIPFilterParamsAction is 'httpRedirect'. The following macro substitutions are applicable in this context: $URL, $MAC, $IP, $SUB, $SAP, $SAPDESC, $CID, and $RID. Note that the value of tIPFilterParamsRedirectURL is silently cleared by the system if tIPFilterParamsAction is set to any value other than httpRedirect.

OBJECT-TYPE

If different from 0, the object tIPFilterParamsSrcIpFullMask specifies the IP Mask value for this policy IP Filter entry. The mask is ANDed with the received Source IP address to match the tIPFilterParamsSourceIpAddr. If the value of tIPFilterParamsSourceIpMask is non zero, it will be equal to the mask expressed the object tIPFilterParamsSrcIpFullMask. If both tIPFilterParamsSourceIpMask and tIPFilterParamsSrcIpFullMask are set to 0, no matching is done on the Source IP address. This object should contain consecutive ones and zeros. Both a regular and an inverse mask is allowed (i.e. the sequence of consecutive ones can appear at the front or at the end of the mask). If a regular mask is specified for tIPFilterParamsSrcIpFullMask then the value of tIPFilterParamsSourceIpMask will be changed to reflect this value. If an inverse is specified, the value of tIPFilterParamsSourceIpMask will be set to 0.

OBJECT-TYPE

If different from 0, the object tIPFilterParamsDestIpFullMask specifies the IP Mask value for this policy IP Filter entry. The mask is ANDed with the received Destination IP address to match the tIPFilterParamsDestinationIpAddr. If the value of tIPFilterParamsDestinationIpMask is non zero, it will be equal to the mask expressed the object tIPFilterParamsDestIpFullMask. If both tIPFilterParamsDestinationIpMask and tIPFilterParamsDestIpFullMask are set to 0, no matching is done on the Destination IP address. This object should contain consecutive ones and zeros. Both a regular and an inverse mask is allowed (i.e. the sequence of consecutive ones can appear at the front or at the end of the mask). If a regular mask is specified for tIPFilterParamsDestIpFullMask then the value of tIPFilterParamsDestinationIpMask will be changed to reflect this value. If an inverse is specified, the value of tIPFilterParamsDestinationIpMask will be set to 0.

OBJECT-TYPE

The value of tIPFilterParamsIngrHitByteCount indicates the number of bytes of all ingress packets that matched this entry.

OBJECT-TYPE

The value of tIPFilterParamsEgrHitByteCount indicates the number of bytes of all egress packets that matched this entry.

OBJECT-TYPE

tIPFilterParamsFwdRtrId specifies, if different from '0', the router id into which the packet should be forwarded if it hits this filter entry. The action of this entry should be 'forward' in such a case. Note that the value of tIPFilterParamsFwdRtrId is silently cleared by the system if tIPFilterParamsAction is set to value other than 'forward'(2) or any object related to 'forward' other than tIPFilterParamsFwdRtrId, tIPFilterParamsForwardNH or tIPFilterParamsForwardNHIndirect is set.

OBJECT-TYPE

tIPFilterParamsSrcRouteOption specifies, when enabled, that this filter should match if a (strict or loose) source route option is present/not present at any location within the IP header, as per the value of this object.

OBJECT-TYPE

The value of this object specifies the IP prefix list used as match criterion for the source IP address. The value specified for this object must correspond to a prefix list defined in tFilterPrefixListTable. If the value of this object is empty then the values of the objects tIPFilterParamsSourceIpAddr and tIPFilterParamsSourceIpMask are used as source IP address match criterion. When this object is set to a non-empty value then the objects tIPFilterParamsSourceIpAddr and tIPFilterParamsSourceIpMask are reset to their default values by the system. Vice versa, when a new (non-default) value is provided for the objects tIPFilterParamsSourceIpAddr and tIPFilterParamsSourceIpMask then this object is reset to its default (empty) value by the system. An attempt to set tIPFilterParamsSrcIpPrefixList to a non-default value in combination with setting any of tIPFilterParamsSourceIpAddr or tIPFilterParamsSourceIpMask to (a) non-default value(s) is rejected by the system

OBJECT-TYPE

The value of this object specifies the IP prefix list used as match criterion for the destination IP address. The value specified for this object must correspond to a prefix list defined in tFilterPrefixListTable. If the value of this object is empty then the values of the objects tIPFilterParamsDestinationIpAddr and tIPFilterParamsDestinationIpMask are used as destination IP address match criterion. When this object is set to a non-empty value then the objects tIPFilterParamsDestinationIpAddr and tIPFilterParamsDestinationIpMask are reset to their default values by the system. Vice versa, when a new (non-default) value is provided for the objects tIPFilterParamsDestinationIpAddr and tIPFilterParamsDestinationIpMask then this object is reset to its default (empty) value by the system. An attempt to set tIPFilterParamsDstIpPrefixList to a non-default value in combination with setting any of tIPFilterParamsDestinationIpAddr or tIPFilterParamsDestinationIpMask to (a) non-default value(s) is rejected by the system

OBJECT-TYPE

This object specifies how the source port objects (tIPFilterParamsSourcePortValue1, tIPFilterParamsSourcePortValue2, tIPFilterParamsSourcePortOperator, tIPFilterParamsSrcPortList) and destination port objects (tIPFilterParamsDestPortValue1, tIPFilterParamsDestPortValue2, tIPFilterParamsDestPortOperator, tIPFilterParamsDstPortList) are combined to form the filter match criterion. See description of TFltrPortSelector.

OBJECT-TYPE

The value of this object specifies the port-list used as match criterion for the source port. The value specified for this object must correspond to a port-list defined in tFilterPortListTable. If the value of this object is empty then the values of the objects tIPFilterParamsSourcePortValue1, tIPFilterParamsSourcePortValue2, and tIPFilterParamsSourcePortOperator are used as source port match criterion. When this object is set to a non-empty value then the objects tIPFilterParamsSourcePortValue1, tIPFilterParamsSourcePortValue2, and tIPFilterParamsSourcePortOperator are reset to their default values by the system. Vice versa, when a new (non-default) value is provided for one of the objects tIPFilterParamsSourcePortValue1, tIPFilterParamsSourcePortValue2, or tIPFilterParamsSourcePortOperator then tIPFilterParamsSrcPortList is reset to its default (empty) value by the system. Setting any one of the objects tIPFilterParamsSourcePortValue1, tIPFilterParamsSourcePortValue2, or tIPFilterParamsSourcePortOperator to a non-default value in combination with a non-default value for the object tIPFilterParamsSrcPortList is rejected by the system.

OBJECT-TYPE

The value of this object specifies the port-list used as match criterion for the destination port. The value specified for this object must correspond to a port-list defined in tFilterPortListTable. If the value of this object is empty then the values of the objects tIPFilterParamsDestPortValue1, tIPFilterParamsDestPortValue2, and tIPFilterParamsDestPortOperator are used as destination port match criterion. When this object is set to a non-empty value then the objects tIPFilterParamsDestPortValue1, tIPFilterParamsDestPortValue2, and tIPFilterParamsDestPortOperator are reset to their default values by the system. Vice versa, when a new (non-default) value is provided for one of the objects tIPFilterParamsDestPortValue1, tIPFilterParamsDestPortValue2, or tIPFilterParamsDestPortOperator then tIPFilterParamsDstPortList is reset to its default (empty) value by the system. Setting any one of the objects tIPFilterParamsDestPortValue1, tIPFilterParamsDestPortValue2, or tIPFilterParamsDestPortOperator to a non-default value in combination with a non-default value for the object tIPFilterParamsDstPortList is rejected by the system.

OBJECT-TYPE

The value of this object specifies whether or not the value of tIPFilterParamsRedirectURL can be overridden by a Radius VSA. The default value is false (i.e. the URL cannot be overridden by Radius). The value of tIPFilterParamsRdirAllwRadOvrd is relevant only if the value of tIPFilterParamsAction is httpRedirect. Setting the value of tIPFilterParamsRdirAllwRadOvrd to true is ignored by the system if the value of tIPFilterParamsAction is not httpRedirect. Furthermore, the value of tIPFilterParamsRdirAllwRadOvrd is silently reset to false by the system if tIPFilterParamsAction is set to any value other than httpRedirect.

OBJECT-TYPE

The value of this object specifies the name of the NAT policy to be used when the value of tIPFilterParamsAction is nat. If the value is empty then a default policy is used. If the value is non-empty then it must correspond to a policy defined in tmnxNatPlcyTable. The value of tIPFilterParamsNatPolicyName is relevant only if the value of tIPFilterParamsAction is nat. Setting the value of tIPFilterParamsNatPolicyName to a non-empty string is ignored by the system if the value of tIPFilterParamsAction is not nat. Furthermore, the value of tIPFilterParamsNatPolicyName is silently reset to an empty string by the system if tIPFilterParamsAction is set to any value other than nat.

OBJECT-TYPE

If different from zero the value of the object tIPFilterParamsFwdLsp together with the value of the object tIPFilterParamsFwdLspRtrId specifies the LSP into which a packet should be forwarded if it hits this filter entry. The value of the object tIPFilterParamsAction of this entry must be 'forward' in such case. Otherwise the value of the object tIPFilterParamsFwdLsp is ignored by the system. Note that the value of tIPFilterParamsFwdLsp is reset to '0' by the system if tIPFilterParamsAction is set to value other than 'forward'(2) or any object related to 'forward' other than tIPFilterParamsFwdLsp or tIPFilterParamsFwdLspRtrId is set. The value of the object tIPFilterParamsFwdLsp cannot be set to a non-zero value if other destinations are already specified. The value has to be '0' if the value of the object tIPFilterParamsFwdLspRtrId is not set (i.e. is '0'). If a non-zero value is set, the value of the object tIPFilterParamsFwdLspRtrId has to be set as well.

OBJECT-TYPE

The value of the object tIPFilterParamsFwdLspRtrId specifies the router ID that the LSP ID defined by the value of the object tIPFilterParamsFwdLsp belongs to. The value of the object tIPFilterParamsAction of this entry must be 'forward' in such case. Otherwise the value of the object tIPFilterParamsFwdLspRtrId is ignored by the system. Note that the value of tIPFilterParamsFwdLspRtrId is reset to '0' by the system if tIPFilterParamsAction is set to value other than 'forward'(2) or any object related to 'forward' other than tIPFilterParamsFwdLsp or tIPFilterParamsFwdLspRtrId is set. The value of this object cannot be set to a non-zero value if other destinations are already specified. The value has to be '0' if the value of the object tIPFilterParamsFwdLsp is not set (i.e. is '0'). If a non-zero value is set, the value of the object tIPFilterParamsFwdLsp has to be set as well. The ID of the base router or '0' are the only allowed value with this version of the product.

OBJECT-TYPE

Contains a List of all mac filters configured on this system.

OBJECT-TYPE

Information about a particular MAC Filter. Entries are created/deleted by user. Entries have a presumed StorageType of nonVolatile.

OBJECT-TYPE

Uniquely identifies a mac filter as configures on this system. Values outside of range 1..65535 are reserved for entries dynamically created by the system and cannot be used in any SNMP SET operation.

OBJECT-TYPE

This object allows entries to be created and deleted in the tMacFilterTable.

OBJECT-TYPE

This object specifies the scope of this filter definition. The value 'system(4)' is not supported.

OBJECT-TYPE

User-provided description for this filter.

OBJECT-TYPE

The action to take for packets that do not match any filter entries. The only allowed values for this field are drop(1) and forward(2).

OBJECT-TYPE

tMacFilterType specifies which type of entries this mac filter can contain. If tMacFilterType is set to 'normal(1)', all match criteria are accepted except the criteria mentioned below that belong to type isid(2) and vid(3). If tMacFilterType is set to 'isid(2)' the only accepted match criteria for the filter entries are: - tMacFilterParamsLowISID - tMacFilterParamsHighISID If tMacFilterType is set to vid(3) the only accepted match criteria for the filter entries are: - tMacFilterParamsInnerTagValue - tMacFilterParamsInnerTagMask - tMacFilterParamsOuterTagValue - tMacFilterParamsOuterTagMask tMacFilterType can only be changed if the filter is not applied and has no entries.

OBJECT-TYPE

The value of tMacFilterName specifies the name to associate with this filter.

OBJECT-TYPE

A table of all MAC filter match entries for all MAC filters.

OBJECT-TYPE

Information about a particular MAC Filter entry. Every MAC Filter can have zero or more MAC Filter match entries. A filter entry with no match criteria set will match every packet, and the entry action will be taken. Entries are created/deleted by user. There is no StorageType object, entries have a presumed StorageType of nonVolatile.

OBJECT-TYPE

This is the secondary index for the entry. Every mac filter can have multiple entries, therefore every mac filter entry is identified by the tMacFilterId and tMacFilterParamsIndex.

OBJECT-TYPE

This object allows entries to be created and deleted in the tMacFilterParamsTable.

OBJECT-TYPE

This object specifies the log to use for packets that match this entry. The value zero indicates that logging is disabled.

OBJECT-TYPE

User-provided description for this filter entry.

OBJECT-TYPE

The action to take for packets that match this filter entry. The value default(3) specifies this entry to inherit the behavior defined as the default for the filter. The values nat(5), reassemble(6), gtpLclBrkout(7) and forwardEsiL3(9) are not allowed. The object tMacFilterParamsAction supports only subset of filter actions. The object tMacFltrEntryActAction supports all actions. It's recommended to use tMacFltrEntryActAction instead of tMacFilterParamsAction.

OBJECT-TYPE

The type of mac frame for which we are defining this match criteria. For filter entries in a MAC filter of type tMacFilterType = dot1q or tMacFilterType qinq the default value for this object is set to ethernetII (3), and no changes are allowed. In all other cases the default value is set to e802dot3 (0)

OBJECT-TYPE

Source MAC to match for this policy MAC filter entry.

OBJECT-TYPE

Source MAC mask value for this policy MAC filter entry. The mask is ANDed with the MAC to match tMacFilterParamsSrcMAC. A cleared bit means ignore this bit, do not match. A set bit means match this bit with tMacFilterParamsSrcMAC. Use the value 00-00-00-00-00-00 to disable this filter criteria.

OBJECT-TYPE

Destination MAC mask value for this policy MAC filter entry.

OBJECT-TYPE

Destination MAC mask value for this policy MAC filter entry. The mask is ANDed with the MAC to match tMacFilterParamsDstMAC. A cleared bit means ignore this bit, do not match. A set bit means match this bit with tMacFilterParamsDstMAC. Use the value 00-00-00-00-00-00 to disable this filter criteria.

OBJECT-TYPE

IEEE 802.1p priority value for this policy MAC filter entry. Use -1 to disable matching this filter criteria.

OBJECT-TYPE

IEEE 802.1p priority mask value for this policy MAC filter entry. Use zero to disable matching, use 7 to match everything.

OBJECT-TYPE

Ethertype for this policy MAC filter entry. Use -1 to disable matching by this criteria. This object has no significance if the object tMacFilterParamsFrameType is not set to Ethernet_II.

OBJECT-TYPE

MAC DSAP to match for this policy MAC filter entry. This object has no significance if the object tMacFilterParamsFrameType is not set to 802dot2LLC. In order to reset the value to the default value, both objects tMacFilterParamsDsap and tMacFilterParamsDsapMask need to be modified together to the default value.

OBJECT-TYPE

MAC DSAP mask for this policy MAC filter entry. Use 0 to disable matching by this criteria. This object has no significance if the object tMacFilterParamsFrameType is not set to 802dot2LLC. In order to reset the value to the default value, both objects tMacFilterParamsDsap and tMacFilterParamsDsapMask need to be modified together to the default value.

OBJECT-TYPE

MAC SSAP to match for this policy MAC filter entry. This object has no significance if the object tMacFilterParamsFrameType is not set to 802dot2LLC. In order to reset the value to the default value, both objects tMacFilterParamsSsap and tMacFilterParamsSsapMask need to be modified together to the default value.

OBJECT-TYPE

MAC SSAP mask for this policy MAC filter entry. Use 0 to disable matching by this criteria. This object has no significance if the object tMacFilterParamsFrameType is not set to 802dot2LLC. In order to reset the value to the default value, both objects tMacFilterParamsSsap and tMacFilterParamsSsapMask need to be modified together to the default value.

OBJECT-TYPE

MAC SNAP PID to match for this policy MAC filter entry. Use -1 to disable matching by this criteria. This object has no significance if object tMacFilterParamsFrameType is not set to 802dot2SNAP.

OBJECT-TYPE

MAC SNAP OUI to match. The values zero(2) and nonZero(3) specify what to match. Matching can be disabled by the use of the value off(1). This object has no significance if the object tMacFilterParamsFrameType is not set to 802dot2SNAP.

OBJECT-TYPE

This object indicates the number of times an ingress packet matched this entry.

OBJECT-TYPE

This object indicates the number of times an egress packet matched this entry.

OBJECT-TYPE

tMacFilterParamsLogInstantiated indicates if the filter log for this filter entry has been instantiated or not.

OBJECT-TYPE

tMacFilterParamsFwdSvcId indicates the service id of the destination for this MAC filter entry. A value of 0 indicates that there is currently no active SAP or SDP destination.

OBJECT-TYPE

tMacFilterParamsFwdSapPortId specifies the sap port identity of the destination for this MAC filter entry. A value of 0 indicates that there is currently no SAP destination defined. A value different from 0 can only be specified if the value of the tMacFilterParamsAction object of this entry is 'forward'. In addition a non-zero value can only be given if the object tMacFilterParamsFwdSdpBind has a zero value. Note that the value of tMacFilterParamsFwdSapPortId is silently cleared by the system if tMacFilterParamsAction is set to value other than 'forward'(2), or any object related to 'forward' other than tMacFilterParamsFwdSvcId, tMacFilterParamsFwdSapPortId or tMacFilterParamsFwdSapEncapVal is set.

OBJECT-TYPE

tMacFilterParamsFwdSapEncapVal specifies the sap port encap value of the destination SAP for this MAC filter entry. A value different from 0 can only be specified if the tMacFilterParamsFwdSapPortId object has a non zero value, and if the value of the tMacFilterParamsAction object of this entry is 'forward'. In addition a non-zero value can only be given if the object tMacFilterParamsFwdSdpBind has a zero value. A value of 0 indicates that either 1) the sap encapsulation value is not specified when tMacFilterParamsFwdSapPortId and tMacFilterParamsFwdSvcId have valid values; or 2) that there is no SAP destination. Note that the value of tMacFilterParamsFwdSapEncapVal is silently cleared by the system if tMacFilterParamsAction is set to value other than 'forward'(2), or any object related to 'forward' other than tMacFilterParamsFwdSvcId, tMacFilterParamsFwdSapPortId or tMacFilterParamsFwdSapEncapVal is set.

OBJECT-TYPE

tMacFilterParamsFwdSdpBind specifies the sdp bind identity of the destination for this MAC filter entry. A value of 0 indicates that there is currently no SDP binding defined. A value different from 0 can only be specified if the value of the tMacFilterParamsAction object of this entry is 'forward'. In addition a non-zero value can only be given if the objects tMacFilterParamsFwdSapPortId and tMacFilterParamsFwdSapEncapVal have a zero value. Note that the value of tMacFilterParamsFwdSdpBind is silently cleared by the system if tMacFilterParamsAction is set to value other than 'forward'(2), or any object related to 'forward' other than tMacFilterParamsFwdSvcId or tMacFilterParamsFwdSdpBind is set.

OBJECT-TYPE

tMacFilterParamsTimeRangeName specifies the tmnxTimeRangeEntry to be associated with this filter entry. A value for this object can only be specified during row creation, and cannot be altered later on. Also, a value is accepted only if the tmnxTimeRangeEntry is defined in the TIMETRA-SCHEDULER-MIB::tmnxTimeRangeTable.tTimeRangeName. This object is obsoleted in release 14.0.

OBJECT-TYPE

tMacFilterParamsTimeRangeState indicates whether or not the entry is currently in effect. - timeRangeNotApplic: no time range is applicable for this entry. - timeRangeNotActive: A time range is defined in tMacFilterParamsTimeRangeName, but is not active at this moment. Consequently the filter entry is not installed. - timeRangeActive. A time range is defined in tMacFilterParamsTimeRangeName, and is activated successfully. - timeRangeActiveDownloadFailed: A time range is defined in tMacFilterParamsTimeRangeName, and is activated, but the corresponding filter entry could not be installed due to resource problems. This object is obsoleted in release 14.0.

OBJECT-TYPE

The value of tMacFilterParamsRedirectURL specifies the URL to redirect to, when the value of tMacFilterParamsAction is 'httpRedirect'. Note that the value of tMacFilterParamsRedirectURL is silently cleared by the system if tMacFilterParamsAction is set to any value other than 'httpRedirect'.

OBJECT-TYPE

The value of tMacFilterParamsIngrHitByteCount indicates the number of bytes of all ingress packets that matched this entry.

OBJECT-TYPE

The value of tMacFilterParamsEgrHitByteCount indicates the number of bytes of all egress packets that matched this entry.

OBJECT-TYPE

The value of tMacFilterParamsLowISID specifies the lowest value of the 24 bit (0..16777215) service instance identifier for this service that matches this entry. The default value of -1 indicates no ISID matching will be performed. The value of this field can be equal to but not lower than the value of the tMacFilterParamsHighISID field. Changing the value of this field might also change the value of tMacFilterParamsHighISID: A value of -1 will change the value of tMacFilterParamsHighISID to -1. Changing the value of this field from -1 to any other value will change the value of tMacFilterParamsHighISID to this same value. Note that tMacFilterParamsLowISID and tMacFilterParamsHighISID can only be set if tMacFilterType is set to 'isid(1)'.

OBJECT-TYPE

The value of tMacFilterParamsHighISID specifies the highest value of the 24 bit (0..16777215) service instance identifier for this service that matches this entry. The default value of -1 indicates no ISID matching will be performed. The value of this field can be equal to but not higher than the value of the tMacFilterParamsLowISID field. Changing the value of this field might also change the value of tMacFilterParamsLowISID: A value of -1 will change the value of tMacFilterParamsLowISID to -1. Changing the value of this field from -1 to any other value will change the value of tMacFilterParamsLowISID to this same value. Note that tMacFilterParamsLowISID and tMacFilterParamsHighISID can only be set if tMacFilterType is set to 'isid(1)'.

OBJECT-TYPE

The value of tMacFilterParamsInnerTagValue specifies the value to match against the VID of the second VLAN tag in the packet that is carried transparently through the service (the second vlan tag after the service delimiting tags). This object can only be set if tMacFilterType is set to 'vid(3)'. The (default) value of '-1' indicates no inner VLAN tag matching will be performed.

OBJECT-TYPE

The value of tMacFilterParamsInnerTagMask is applied as a mask to VID of the inner VLAN tag of the packet prior to comparing it with tMacFilterParamsInnerTagValue. The inner tag is the second tag in the packet that is carried transparently through the service (the second tag after the service delimiting tags). This object can only be set if tMacFilterType is set to 'vid(3)'.

OBJECT-TYPE

The value of tMacFilterParamsOuterTagValue specifies the value to match against the VID of the first VLAN tag in the packet that is carried transparently through the service (the first vlan tag after the service delimiting tags). This object can only be set if tMacFilterType is set to 'vid(3)'. The (default) value of '-1' indicates no outer VLAN tag matching will be performed.

OBJECT-TYPE

The value of tMacFilterParamsOuterTagMask is applied as a mask to VID of the outer VLAN tag of the packet prior to comparing it with tMacFilterParamsOuterTagValue. The outer tag is the first tag in the packet that is carried transparently through the service (the first tag after the service delimiting tags). This object can only be set if tMacFilterType is set to 'vid(3)'.

OBJECT-TYPE

The value of the object tMacFilterParamsEsi specifies the ethernet segment identifier (ESI) of the first ESI identified appliance in Nuage service chain. When the value of tMacFilterParamsAction is 'forwardEsiL2' packets matching the filter entry are forwarded to the appliance using EVPN-resolved VXLAN tunnel in the specified VPLS service (tMacFilterParamsFwdEsiSvcId). The value '0' indicates that there is no ESI specified. The value of tMacFilterParamsEsi is ignored by the system if the value of tMacFilterParamsAction is different from 'forwardEsiL2'. The value of tMacFilterParamsAction can be set to 'forwardEsiL2' only if tMacFilterParamsEsi and tMacFilterParamsFwdEsiSvcId are set to non zero values.

OBJECT-TYPE

The value of the object tMacFilterParamsFwdEsiSvcId specifies the identifier of the VPLS used for VPN/DC connectivity. The value '0' indicates that no VPLS identifier is specified. The value of tMacFilterParamsFwdEsiSvcId is ignored by the system if the value of tMacFilterParamsAction is different from 'forwardEsiL2'. The value of tMacFilterParamsAction can be set to 'forwardEsiL2' only if tMacFilterParamsEsi and tMacFilterParamsFwdEsiSvcId are set to non zero values.

OBJECT-TYPE

The value of the object tMacFilterParamsPbrDwnActOvr specifies the filter action which will be performed when the PBR/PBF target for this entry is not available. If the value of tMacFltrEntryActAction is not one of the following values then tMacFilterParamsPbrDwnActOvr must be set to the value 'none': - forwardEsiL2 - forwardSap - forwardSdp If the value of tMacFilterParamsPbrDwnActOvr is different from 'none' then PBF destination availability checking for an entry is turned on. There is a limit to the number of filter entries with the destination availability checking turned on. Entries with the value of tMacFltrEntryActAction equal to 'forwardEsiL2' are not counted against this limit. Refer to the description of the textual convention TFilterPbrDownActionOvr for more details.

OBJECT-TYPE

The value of the object tMacFilterParamsStickyDst specifies how long the system will wait (in seconds) until it activates the best action (action with available PBF destination and the highest priority). Until then the action specified by tMacFilterParamsPbrDwnActOvr will be taken on a packet matching the filter entry. After the value of the active destination is fixed it will remain unchanged until the active PBF destination becomes unreachable. The value of -1 indicates that the property of PBF destination stickiness is turned off. When the property of stickiness is turned off the active PBF destination is always the one which is available and has the highest priority. The countdown starts when there was no PBR/PBF destination reachable and any PBR/PBF destination becomes reachable. tMacFilterParamsStickyDst can be set to value other than -1 only if the value of tMacFltrEntryActAction is 'forwardSap' or 'forwardSdp'.

OBJECT-TYPE

The value of the object tMacFilterParamsHoldRemain indicates the remaining time in seconds, until the best action will become active and will be fixed. Best action is: - primary action if PBR target status of primary action is up. - secondary action if PBR target status of secondary action is up and PBR target status of primary action is down. - none if both PBR targets are down

OBJECT-TYPE

The value of the object tMacFilterParamsDownloadAct indicates the filter entry action downloaded to IOM. Refer to the description of the textual convention TFilterDownloadedAction for more information.

OBJECT-TYPE

A table of all filter logs.

OBJECT-TYPE

Information about a particular Filter Log entry.

OBJECT-TYPE

This is the index for the entry. An entry cannot be created with an id of 0.

OBJECT-TYPE

This object allows entries to be created and deleted in the tFilterLogTable.

OBJECT-TYPE

This object specifies the destination of the log.

OBJECT-TYPE

User-provided description for this filter log entry.

OBJECT-TYPE

The object tFilterLogMaxNumEntries specifies the maximum number of entries that the log can store. The value of tFilterLogMaxNumEntries can be set to any value other than zero only if tFilterLogDestination is 'memory'.

OBJECT-TYPE

The object tFilterLogSysLogId specifies the syslog Id to be used as destination. The value of tFilterLogSysLogId can be set to any value other than zero only if tFilterLogDestination is 'syslog'.

OBJECT-TYPE

The object tFilterLogFileId specifies the File Id to be used as destination. The value of tFilterLogFileId can be set to any value other than zero only if tFilterLogDestination is 'file'.

OBJECT-TYPE

The value of the object tFilterLogStopOnFull specifies what should happen when tFilterLogMaxNumEntries is reached. The value true, specifies that logging will stop. The value false specifies that wrap-around will be used.

OBJECT-TYPE

The value of the object tFilterLogEnabled specifies whether the logging is enabled or disabled

OBJECT-TYPE

The value of tFilterLogSummaryEnabled specifies whether or not summarization of filter log entries is performed. Summarization is only allowed in case tFilterLogDestination is set to syslog.

OBJECT-TYPE

The value of tFilterLogSummaryCrit1 specifies how filter log entries will be summarized. This field is only meaningful if the object tFilterLogSummaryEnabled is set to true.

OBJECT-IDENTITY

OBJECT-TYPE

tFilterLogMaxInstances maintains the maximum allowed instances of filter logs allowed on the system

OBJECT-TYPE

tFilterLogInstances maintains the instances of filter logs presently existing on the system

OBJECT-TYPE

tFilterLogBindings maintains the count of the configured filter log bindings presently existing on the system. The bindings get instantiated when the filter is instantiated

OBJECT-IDENTITY

OBJECT-TYPE

Used by tIPFilterPBRPacketsDrop to report the failure reason code.

OBJECT-TYPE

The value of the object tFilterParmRow indicates the OID of the row status of the applicable filter parameter table. This can be a row from either one of the following tables: - tIPFilterParamsTable; - tMacFilterParamsTable; or - tIPv6FilterParamsTable

OBJECT-TYPE

The value of the object tFilterAlarmDescription is a printable character string which contains information about the cause of the problem.

OBJECT-TYPE

The value of the object tFilterId, together with the object tFilterType uniquely defines the filter for which this notification is generated.

OBJECT-TYPE

The value of the object tFilterType, together with the object tFilterId uniquely defines the filter for which this notification is generated.

OBJECT-TYPE

The value of the object tFilterSubInsSpaceOwner, specifies for which application, capable of inserting filter entries, this notification is generated.

OBJECT-TYPE

The value of the object tFilterThresholdReached, specifies the threshold reached at the moment this notification was generated.

OBJECT-TYPE

The value of the object tFltrFlowSpecProblem, indicates which problem has occurred while processing a BGP flowspec NLRI in the filter module.

OBJECT-TYPE

The value of the object tFltrFlowSpecProblemDescription may contain a more detailed problem description then as given by tFltrFlowSpecProblem.

OBJECT-TYPE

The value of the object tFltrFLowSpecNLRI contains at most the first 30 octets of the NLRI causing the problem.

OBJECT-TYPE

The value of the object tFltrFlowSpecVrtrId indicates the virtual router Id to which the NLRI belongs.

OBJECT-TYPE

The value of the object tFltrPrefixListType indicates the type of prefix list.

OBJECT-TYPE

The value of the object tFltrPrefixListName indicates the name of the prefix list.

OBJECT-TYPE

The value of tFltrApplyPathSource indicates the source of the apply-path rule.

OBJECT-TYPE

The value of tFltrApplyPathIndex indicates the index of the apply-path rule.

OBJECT-TYPE

The value of the object tFltrNotifDescription may contain a description text.

OBJECT-TYPE

The value of the object tFltrMdaId contains the MDA-id of the mda on which an filter event is being reported.

OBJECT-IDENTITY

OBJECT-TYPE

timestamp of last change to tFilterObjects.

OBJECT-TYPE

Contains a List of all redirect policies configured on this system.

OBJECT-TYPE

Information about a particular redirect policy. Entries are created/deleted by user.

OBJECT-TYPE

tFilterRedirectPolicy uniquely identifies each redirect policy configured on this system.

OBJECT-TYPE

tFilterRPRowStatus allows entries to be created and deleted in the tFilterRedirectPolicyTable.

OBJECT-TYPE

User-provided description for this redirect policy is maintained in the object tFilterRPDescription.

OBJECT-TYPE

tFilterRPAdminState holds the admin state of the policy. If the admin state is 'outOfService', the tests will not be conducted.

OBJECT-TYPE

tFilterRPActiveDest indicates the IP address of the active destination. A value of 0 indicates that there is currently no active destination. This object is obsoleted in release 13.0.

OBJECT-TYPE

The value of the object tFilterRPVrtrId specifies the target routing instance as part of the redirect policy. When the target routing instance is configured (not equal to 0), the following applies: - Ping and unicast-reachability tests configured in a redirect policy are now executed in the routing instance specified by the redirect policy regardless of what routing instance is the filter using this redirect policy deployed in. - When packets are routed to a destination configured in a redirect policy with router instance specified (as result of filter match), routing is executed in the router instance context configured in the redirect policy regardless of the routing context for the interface on which the packet arrived. Note that if all destinations are down, the forward action is still executed in the routing instance of the incoming interface and not the routing instance of the redirect policy. If PBR specifies action forward router, then deploying the policy on card not supporting such action will result in action forward using incoming interface routing context. - If the H/W does not support the next-hop router PBR action, action forward is executed (even if the router instance in the action is the same as the router instance of the incoming interface). If the target routing instance is not configured (equal to 0), the following applies: - Redirect policy can be deployed in any VPRN or GRT routing context but a test will only run in GRT context regardless of where the policy is deployed. - The PBR will execute in the routing context of the ingress interface. SNMP and URL tests can be configured only if the target routing instance is not configured.

OBJECT-TYPE

The value of the object tFilterRPActiveDestAddrType indicates the context in which the values of the objects tFilterRPActiveDestAddr are interpreted. Only following values are supported: unknown(0) ipv4(1) ipv6(2)

OBJECT-TYPE

The value of the object tFilterRPActiveDestAddr indicates the IP address of the active destination. A value of 0 indicates that there is currently no active destination. The value must be consistent with the IP version value of the associated tFilterRPActiveDestAddrType object.

OBJECT-TYPE

The value of the object tFilterRPDstStickiness specifies the time in seconds, how long the system will wait until it sets and fixes the current best destination as active destination. After the value of active destination is fixed it will remain unchanged until the active destination becomes unreachable. When the value of tFilterRPDstStickiness is -1 the property of destination stickiness is turned off. That means that active destination is always the best one. The countdown starts when there was no destination reachable and any destination becomes reachable.

OBJECT-TYPE

The value of the object tFilterRPBestDstAddrType indicates the context in which the values of the objects tFilterRPActiveDestAddr are interpreted. Only following values are supported: unknown(0) ipv4(1) ipv6(2)

OBJECT-TYPE

The value of the object tFilterRPBestDstAddr indicates the IP address of the available destination with the highest priority. A value of 0 indicates that currently there is no reachable destination. The value must be consistent with the IP version value of the associated tFilterRPActiveDestAddrType object.

OBJECT-TYPE

The value of the object tFilterRPStickinessHoldRemain indicates the remaining time in seconds, until the best destination becomes the active destination and will become fixed.

OBJECT-TYPE

The value of the object tFilterRPNotifyDestChange indicates whether to send tFilterRPActiveDestChangeEvent notification for this redirect policy active destination changes.

OBJECT-TYPE

Contains a List of all redirect destinations configured on this system. This table is obsoleted in release 13.0 and replaced by tFilterRPlcyDstTable.

OBJECT-TYPE

Information about a particular Redirect destination. Entries are created/deleted by user. This object is obsoleted in release 13.0.

OBJECT-TYPE

tFilterRedirectDest holds the IP address of the destination entry. This object is obsoleted in release 13.0.

OBJECT-TYPE

tFilterRDRowStatus allows entries to be created and deleted in the tFilterRedirectDestTable. This object is obsoleted in release 13.0.

OBJECT-TYPE

User-provided description for this destination is maintained in the object tFilterRDDescription. This object is obsoleted in release 13.0.

OBJECT-TYPE

tFilterRDAdminPriority holds the configured base priority for the destination. This object is obsoleted in release 13.0.

OBJECT-TYPE

tFilterRDAdminPriority maintains the operational value of the priority for this destination. The highest operational priority across multiple destinations is used as the preferred destination. A value of '0' is maintained if the destination if tFilterRDOperState is 'outOfService'. This object is obsoleted in release 13.0.

OBJECT-TYPE

tFilterRDAdminState maintains the configured state of the destination. If the admin state is 'outOfService', the tests for this destination will not be conducted. This object is obsoleted in release 13.0.

OBJECT-TYPE

The value of tFilterRDOperState indicates the operational state of the destination. This object is obsoleted in release 13.0.

OBJECT-TYPE

Contains a List of all redirect SNMP tests configured on this system. This table is obsoleted in release 13.0 and replaced by tFilterRPlcySNMPTestTable.

OBJECT-TYPE

Information about a specific SNMP test configured for a destination. Entries are created/deleted by user. This object is obsoleted in release 13.0.

OBJECT-TYPE

tFilterRedirectSNMPTest specifies the name of the SNMP test. This object is obsoleted in release 13.0.

OBJECT-TYPE

tFilterRSTRowStatus allows tests to be created and deleted in the tFilterRedirectSNMPTestTable. This object is obsoleted in release 13.0.

OBJECT-TYPE

tFilterRSTOID stores the OID of the object to be fetched from the destination. The value of this object can only be changed if the object tFilterRSTCommunity is changed at the same time. This object is obsoleted in release 13.0.

OBJECT-TYPE

The value of tFilterRSTCommunity is the SNMPv1 or SNMPv2c Community String or the SNMPv3 Context Name used to conduct this SNMP test as described in RFC2571 and RFC2737. When the value of tFilterRSTSNMPVersion is 'snmpv1' or 'snmpv2c' this object represents a community string. When the value of tFilterRSTSNMPVersion is 'snmpv3' this object represents a SNMPv3 context name. The value of this object can only be changed if the object tFilterRSTOID is changed at the same time. This object is obsoleted in release 13.0.

OBJECT-TYPE

tFilterRSTSNMPVersion specifies the SNMP PDU format to be used while conducting the test. Currently only snmpv2c is supported. This object is obsoleted in release 13.0.

OBJECT-TYPE

The value of tFilterRSTInterval specifies the amount of time in seconds between consecutive requests sent to the far end host. This object is obsoleted in release 13.0.

OBJECT-TYPE

The value of tFilterRSTTimeout specifies the amount of time in seconds that is allowed for receiving a response from the far end host. If a reply is not received within this time the far end host is considered unresponsive. This object is obsoleted in release 13.0.

OBJECT-TYPE

The value of tFilterRSTDropCount specifies the number of consecutive requests that must fail for the destination to declared unreachable. This object is obsoleted in release 13.0.

OBJECT-TYPE

The value of tFilterRSTHoldDown specifies the amount of time in seconds that the system should be held down if any of the test has marked it unreachable. This object is obsoleted in release 13.0.

OBJECT-TYPE

The value of tFilterRSTHoldDownRemain indicates the amount of time in seconds that the system will remain in held down state before being used again. This object is obsoleted in release 13.0.

OBJECT-TYPE

tFilterRSTLastActionTime maintains the time stamp when this test received a response for a probe sent out. This object is obsoleted in release 13.0.

OBJECT-TYPE

The object tFilterRSTLastOID holds the OID received in the response. This object is obsoleted in release 13.0.

OBJECT-TYPE

tFilterRSTLastType maintains the type of the value received. A value of none(0) indicated that no value has been received. This object is obsoleted in release 13.0.

OBJECT-TYPE

The value tFilterRSTLastType is 'counter32'. This object is obsoleted in release 13.0.

OBJECT-TYPE

The value tFilterRSTLastType is 'unsigned32'. This object is obsoleted in release 13.0.

OBJECT-TYPE

The value tFilterRSTLastType is 'timeTicks'. This object is obsoleted in release 13.0.

OBJECT-TYPE

The value tFilterRSTLastType is 'integer32'. This object is obsoleted in release 13.0.

OBJECT-TYPE

The value tFilterRSTLastType is 'octetString'. This object is obsoleted in release 13.0.

OBJECT-TYPE

The value tFilterRSTLastType is 'ipAddress'. Although this seems to be unfriendly for IPv6, we have to recognize that there are a number of older MIBs that do contain an IPv4 format address, known as IpAddress. IPv6 addresses are represented using TAddress or InetAddress, and so the underlying datatype is OCTET STRING, and their value would be stored in the tFilterRSTLastOctetStringVal column. This object is obsoleted in release 13.0.

OBJECT-TYPE

The value tFilterRSTLastType is 'objectId'. This object is obsoleted in release 13.0.

OBJECT-TYPE

The value tFilterRSTLastType is 'counter64'. This object is obsoleted in release 13.0.

OBJECT-TYPE

The value tFilterRSTLastType is 'opaque'. This object is obsoleted in release 13.0.

OBJECT-TYPE

tFilterRSTLastAction maintains impact that the last test probe made on the operational status of the destination as maintained in tFilterRDOperState. If the last action was 'disable', the destination may not be used for tFilterRSTHoldDown seconds. This object is obsoleted in release 13.0.

OBJECT-TYPE

If the last action on the operational state of the destination i.e. tFilterRSTLastAction is 'enable', tFilterRSTLastPrioChange maintains the impact that the last test probe made on the operational priority of the destination. In other cases, this object has no significance and hence should be holding the value '0'. This object is obsoleted in release 13.0.

OBJECT-TYPE

The value of tFilterRSTNextRespIndex indicates the next response index to be used while creating a row in the tFilterRedirectSNMPRespTable. The value of '-1' means that the maximum number of return values for this OID are already configured. This object is obsoleted in release 13.0.

OBJECT-TYPE

Each row in this table holds the effect of the test on the destination for a specific return value. Each row is created once and cannot be modified after creation. Any change attempts will be silently discarded. This table is obsoleted in release 13.0 and replaced by tFilterRPlcySNMPRespTable.

OBJECT-TYPE

Information about action to be taken for a specific destination when a specific response is received. Each row is created once and cannot be modified after creation. Any change attempts will be silently discarded. This object is obsoleted in release 13.0.

OBJECT-TYPE

tFilterRSTRespId holds the response value received from the destination. This object is obsoleted in release 13.0.

OBJECT-TYPE

This object allows response strings to be specified for a specific test and the change it will cause to the priority of the destination. This object is obsoleted in release 13.0.

OBJECT-TYPE

tFilterRSTRespAction specifies the type of change that should be made to the destination priority tFilterRDOperPriority, if the return value is same as tFilterRSTRespId. If tFilterRSTRespPrioChange is 0 this field will be set to 'disable'. This field cannot be modified after creation. Any change attempts will be silently discarded. This object is obsoleted in release 13.0.

OBJECT-TYPE

tFilterRSTRespPrioChange specifies the amount of change to be made to the priority of the destination if the tFilterRSTRespAction is either 'increase' or 'decrease'. If tFilterRSTRespAction is 'disable', this field will be set to 0. This field cannot be modified after creation. Any change attempts will be silently discarded. This object is obsoleted in release 13.0.

OBJECT-TYPE

The object tFilterRSTRespOID holds the OID to be received in the response. This field cannot be modified after creation. Any change attempts will be silently discarded. This object is obsoleted in release 13.0.

OBJECT-TYPE

tFilterRSTRespType maintains the type of the value to be received. Note: types 'objectId' and 'counter64' are not supported for now, and will be rejected when used. This field cannot be modified after creation. Any change attempts will be silently discarded. This object is obsoleted in release 13.0.

OBJECT-TYPE

The value tFilterRSTRespType is 'counter32'. This field cannot be modified after creation. Any change attempts will be silently discarded. This object is obsoleted in release 13.0.

OBJECT-TYPE

The value tFilterRSTRespType is 'unsigned32'. This field cannot be modified after creation. Any change attempts will be silently discarded. This object is obsoleted in release 13.0.

OBJECT-TYPE

The value tFilterRSTRespType is 'timeTicks'. This field cannot be modified after creation. Any change attempts will be silently discarded. This object is obsoleted in release 13.0.

OBJECT-TYPE

The value tFilterRSTRespType is 'integer32'. This field cannot be modified after creation. Any change attempts will be silently discarded. This object is obsoleted in release 13.0.

OBJECT-TYPE

The value tFilterRSTRespType is 'octetString'. This field cannot be modified after creation. Any change attempts will be silently discarded. This object is obsoleted in release 13.0.

OBJECT-TYPE

The value tFilterRSTRespType is 'ipAddress'. Although this seems to be unfriendly for IPv6, we have to recognize that there are a number of older MIBs that do contain an IPv4 format address, known as IpAddress. IPv6 addresses are represented using TAddress or InetAddress, and so the underlying datatype is OCTET STRING, and their value would be stored in the tFilterRSTOctetStringVal column. This field cannot be modified after creation. Any change attempts will be silently discarded. This object is obsoleted in release 13.0.

OBJECT-TYPE

The response value if tFilterRSTRespType is set to 'objectId'. This field cannot be modified after creation. Any change attempts will be silently discarded. This object is obsoleted in release 13.0.

OBJECT-TYPE

The response value if tFilterRSTRespType is set to 'counter64'. This field cannot be modified after creation. Any change attempts will be silently discarded. This object is obsoleted in release 13.0.

OBJECT-TYPE

The value tFilterRSTRespType is 'opaque'. This field cannot be modified after creation. Any change attempts will be silently discarded. This object is obsoleted in release 13.0.

OBJECT-TYPE

Contains a List of all redirect snmp tests configured on this system. This table is obsoleted in release 13.0 and replaced by tFilterRPlcyURLTestTable.

OBJECT-TYPE

Information about a specific URL test configured for a destination. Entries are created/deleted by user. Entries have a presumed StorageType of nonVolatile. This object is obsoleted in release 13.0.

OBJECT-TYPE

tFilterRedirectURLTest holds the name of the URL test. This object is obsoleted in release 13.0.

OBJECT-TYPE

tFilterRUTRowStatus allows tests to be created and deleted in the tFilterRedirectURLTestTable. This object is obsoleted in release 13.0.

OBJECT-TYPE

This object holds the URL to be probed. This object is obsoleted in release 13.0.

OBJECT-TYPE

The HTTP Version to be used while performing the URL test. The system by default uses HTTP Version 1.1 until explicitly specified. This object is obsoleted in release 13.0.

OBJECT-TYPE

The value of tFilterRUTInterval specifies the amount of time in seconds between consecutive requests sent to the far end host. This object is obsoleted in release 13.0.

OBJECT-TYPE

The value of tFilterRUTTimeout specifies the amount of time in seconds that is allowed for receiving a response from the far end host. If a reply is not received within this time the far end host is considered unresponsive. This object is obsoleted in release 13.0.

OBJECT-TYPE

The value of tFilterRUTDropCount specifies the number of consecutive requests that must fail for the destination to declared unreachable. This object is obsoleted in release 13.0.

OBJECT-TYPE

The value of tFilterRUTHoldDown specifies the amount of time in seconds that the system should be held down if any of the test has marked it unreachable. This object is obsoleted in release 13.0.

OBJECT-TYPE

The value of tFilterRUTHoldDownRemain indicates the amount of time in seconds that the system will remain in held down state before being used again. This object is obsoleted in release 13.0.

OBJECT-TYPE

tFilterRUTLastActionTime maintains the time stamp when this test received a response for a probe sent out. This object is obsoleted in release 13.0.

OBJECT-TYPE

tFilterRUTLastRetCode holds the return code received in the last response. This object is obsoleted in release 13.0.

OBJECT-TYPE

tFilterRUTLastAction maintains impact that the last test probe made on the operational status of the destination as maintained in tFilterRDOperState. If the last action was 'disable', the destination may not be used for tFilterRUTHoldDown seconds. This object is obsoleted in release 13.0.

OBJECT-TYPE

If the last action on the operational state of the destination i.e. tFilterRUTLastAction is 'enable', tFilterRUTLastPrioChange maintains the impact that the last test probe made on the operational priority of the destination. In other cases, this object has no significance and hence should be holding the value '0'. This object is obsoleted in release 13.0.

OBJECT-TYPE

Each row in this table holds the effect of the test on the destination for a range of return values. This table is obsoleted in release 13.0 and replaced by tFilterRPlcyURLRespTable.

OBJECT-TYPE

Information about action to be taken for a specific destination when a return value within the range specified between tFilterRedirectURLLowRespCode and tFilterRedirectURLHighRespCode is received. This object is obsoleted in release 13.0.

OBJECT-TYPE

tFilterRedirectURLLowRespCode specifies the lower return code of the range specified by this entry. This object is obsoleted in release 13.0.

OBJECT-TYPE

tFilterRedirectURLHighRespCode specifies the higher return code of the range specified by this entry. This object is obsoleted in release 13.0.

OBJECT-TYPE

tFilterRUTRespRowStatus allows the mapping of a range of return codes returned from a specific test to the change it will cause to the priority of the destination. This object is obsoleted in release 13.0.

OBJECT-TYPE

If the tFilterRUTRespAction is either 'increase(1)' or 'decrease(2)' tFilterRUTRespPrioChange specifies the offset to be applied to the destination base priority (tFilterRDAdminPriority) in order to compute the tFilterRDOperPriority as a result of this test. If the tFilterRUTRespAction is set to 'disable(3)', on the reception of the specified response, the destination will be deemed unusable and the tFilterRDOperPriority will be set to '0'. The value of tFilterRUTRespAction will be forced by the system to the value 'disable(3)' if the tFilterRUTRespPrioChange has the value '0'. Any change attempts will be silently discarded in this case. This object is obsoleted in release 13.0.

OBJECT-TYPE

tFilterRUTRespPrioChange specifies the amount of change to be made to the priority of the destination if the tFilterRUTRespAction is either 'increase' or 'decrease'. If tFilterRUTRespAction is 'disable', tFilterRUTRespPrioChange will be forced to 0. Any change to tFilterRUTRespPrioChange will be silently discarded in this case. Setting the object tFilterRUTRespPrioChange to 0 will cause the value of tFilterRUTRespAction to be set to 'disable'. This object is obsoleted in release 13.0.

OBJECT-TYPE

Contains a List of all redirect Ping tests configured on this system. This table is obsoleted in release 13.0 and replaced by tFilterRPlcyPingTestTable.

OBJECT-TYPE

Information about a specific Ping test configured for a destination. Entries are created/deleted by user. Entries have a presumed StorageType of nonVolatile. This object is obsoleted in release 13.0.

OBJECT-TYPE

This object allows tests to be created and deleted in the tFilterRedirectPingTestTable. This object is obsoleted in release 13.0.

OBJECT-TYPE

The value of tFilterRPTInterval specifies the amount of time in seconds between consecutive requests sent to the far end host. Note that the value of tFilterRPTInterval can only be modified if the value of the corresponding tFilterRPAdminState and/or tFilterRDAdminState object is outOfService. This object is obsoleted in release 13.0.

OBJECT-TYPE

The value of tFilterRPTTimeout specifies the amount of time in seconds that is allowed for receiving a response from the far end host. If a reply is not received within this time the far end host is considered unresponsive. Note that the value of tFilterRPTTimeout can only be modified if the value of the corresponding tFilterRPAdminState and/or tFilterRDAdminState object is outOfService. This object is obsoleted in release 13.0.

OBJECT-TYPE

The value of tFilterRPTDropCount specifies the number of consecutive requests that must fail for the destination to declared unreachable. This object is obsoleted in release 13.0.

OBJECT-TYPE

The value of tFilterRPTHoldDown specifies the amount of time in seconds that the system should be held down if any of the test has marked it unreachable. This object is obsoleted in release 13.0.

OBJECT-TYPE

The value of tFilterRPTHoldDownRemain indicates the amount of time in seconds that the system will remain in held down state before being used again. This object is obsoleted in release 13.0.

OBJECT-TYPE

tFilterRPTLastActionTime maintains the time stamp when this test received a response for a probe sent out. This object is obsoleted in release 13.0.

OBJECT-TYPE

tFilterRPTLastAction maintains impact that the last test probe made on the operational status of the destination as maintained in tFilterRDOperState. If the last action was 'disable', the destination may not be used for tFilterRPTHoldDown seconds. This object is obsoleted in release 13.0.

OBJECT-TYPE

Defines the Nokia SROS series automatic IP filters for providing, via SNMP, the capability of gathering information regarding the same. tAutoIPFilterEntryTable holds a list of all automatic filter entries being used for filtering. This table is obsoleted in release 3.0.

OBJECT-TYPE

Defines an entry in the tAutoIPFilterEntryTable. Entries are created and deleted in this table by the system. Each entry provides information about a single active automatic filter entry. This entry is obsoleted in release 3.0.

OBJECT-TYPE

tAutoIPFilterId serves as a primary index and uniquely identifies an application point such as a routed interface or a SAP. This object is obsoleted in release 3.0.

OBJECT-TYPE

tAutoIPFilterEntrySourceIpAddr specifies the source IP address and also serves as the secondary index to this table. This object is obsoleted in release 3.0.

OBJECT-TYPE

The value of tAutoIPFilterEntrySourceIpMask indicates the number of bits to be matched in the source IP address. This object is obsoleted in release 3.0.

OBJECT-TYPE

Contains a List of all IPv6 filters configured on this system.

OBJECT-TYPE

Information about a particular IPv6 Filter entry. Entries are created/deleted by user. Entries have a presumed StorageType of nonVolatile.

OBJECT-TYPE

The value of the object tIPv6FilterId uniquely identifies an ip filter. User-configured filters have values between (1..65535). Other values are reserved for filters that are created (auto-generated) by the system. Refer to the description of the textual convention TAnyFilterID for more details.

OBJECT-TYPE

The value of the object tIPv6FilterRowStatus specifies the status of the IPv6 filter. The object allows entries to be created and deleted in the tIPv6FilterTable.

OBJECT-TYPE

The value of the object tIPv6FilterScope specifies the scope of this filter definition.

OBJECT-TYPE

The value of the object tIPv6FilterDescription specifies a user-provided description for this filter.

OBJECT-TYPE

The value of the object tIPv6FilterDefaultAction specifies the action to be taken for packets that do not match any of the filter entries. The only allowed values for this field are drop(1) and forward(2).

OBJECT-TYPE

The value of tIPv6FilterRadiusInsertPt specifies at what place the host specific filter entries received from Radius will be inserted in the filter. The area defined here will be dedicated to those entries, no other entries will be allowed. The value 0 means that no Radius provided host specific filter entries can be inserted in the filter. If tIPv6FilterRadiusInsertSize is set to 0, then this object will be put to 0 as well. Any change attempts will result in error.

OBJECT-TYPE

The value of tIPv6FilterRadiusInsertSize specifies how many host specific filter entries received from Radius for subscriber hosts can be inserted in the filter. If tIPv6FilterRadiusInsertPt is set to 0, then this object will be put to 0 as well. Any change attempts will result in error.

OBJECT-TYPE

The value of tIPv6FilterCreditCntrlInsertPt specifies at what place the filter entries received from Credit Control for a particular subscriber host will be inserted in the filter. The area defined here will be dedicated to those entries, no other entries will be allowed. The value 0 means that no Credit Control provided filter entries can be inserted in the filter. If tIPv6FilterCreditCntrlInsertSize is set to 0, then this object will be put to 0 as well. Any change attempts will result in error.

OBJECT-TYPE

The value of tIPv6FilterCreditCntrlInsertSize specifies how many filter entries received from Credit Control can be inserted in the filter. If tIPv6FilterCreditCntrlInsertPt is set to 0, then this object will be put to 0 as well. Any change attempts will result in error.

OBJECT-TYPE

The value of the object tIPv6FilterSubInsertHighWmark specifies the utilization of the filter ranges for filter entry insertion, at which a table full alarm will be raised by the agent. The value 0 indicates that no alarm will be generated.

OBJECT-TYPE

The value of the object tIPv6FilterSubInsertLowWmark specifies the utilization of the filter ranges for filter entry insertion, at which a table full alarm will be cleared by the agent.

OBJECT-TYPE

The value of the object tIpv6FilterCreditCntrlNbrInsertd indicates how many filter entries are currently inserted in the filter on request of credit control.

OBJECT-TYPE

The value of the object tIpv6FilterRadiusNbrInsertd indicates how many host specific filter entries are currently inserted in the filter on request of RADIUS.

OBJECT-TYPE

The value of tIpv6FilterName specifies the name to associate with this filter.

OBJECT-TYPE

The value of tIPv6FilterHostSharedInsertPt specifies at what place the filter entries received from Radius that are shared between several hosts (host common rules) will be inserted in the filter. The area defined here will be dedicated to those entries, no other entries will be allowed. The value 0 means that no Radius provided host common filter entries can be inserted in the filter. If tIPv6FilterHostSharedInsertSize is set to 0, then this object will be put to 0 as well. Any change attempts will result in error.

OBJECT-TYPE

The value of tIPv6FilterHostSharedInsertSize specifies how many host common filter entries received from Radius for subscriber hosts can be inserted in the filter. If tIPv6FilterHostSharedInsertPt is set to 0, then this object will be put to 0 as well. Any change attempts will result in error.

OBJECT-TYPE

The value of the object tIpv6FilterHostSharedNbrInsertd indicates how many host common filter entries are currently inserted in the filter on request of Radius.

OBJECT-TYPE

The value of the object tIPv6FilterHostSharedHighWmark specifies the number of Radius Shared Filters that can be dynamically created in the system before an high watermark notification is generated by the system. The value -1 specifies that no notifications are sent. If any of the watermarks (high or low) is set to -1, both watermarks will be set to -1 by the system.

OBJECT-TYPE

The value of the object tIPv6FilterHostSharedLowWmark specifies the number of Radius Shared Filters that are still dynamically created in the system before an high watermark notification is cleared by the system. The value -1 specifies that no notifications are sent. If any of the watermarks (high or low) is set to -1, both watermarks will be set to -1 by the system.

OBJECT-TYPE

The value of the object tIPv6FilterNbrHostSharedFltrs indicates how many filters are currently created by Radius or Diameter based on this filter. (Both host shared or flow-rule filters.)

OBJECT-TYPE

The value of tIPv6FilterSharedPccRuleInsrtPt specifies at what place the flow-rule filter entries that are received from Diameter and that are shared across several hosts will be inserted in the filter. The range defined here will be reserved for those entries; no other entries will be allowed in this range. The value 0 means that no flow-rule filter entries can be inserted in the filter by Diameter. If tIPv6FilterSharedPccRuleInsrtSiz is set to 0 then tIPv6FilterSharedPccRuleInsrtPt is also set to 0 by the system. Note that the range reserved for shared flow-rule entries must not overlap with that of either tIPv6FilterRadiusInsertPt/tIPv6FilterRadiusInsertSize, tIPv6FilterCreditCntrlInsertPt/tIPv6FilterCreditCntrlInsertSize, or tIPv6FilterHostSharedInsertPt/tIPv6FilterHostSharedInsertSize

OBJECT-TYPE

The value of tIPv6FilterSharedPccRuleInsrtSiz specifies how many flow-rule filter entries that are received from Diameter and that are shared across several hosts can be inserted in the filter. The range defined here will be reserved for those entries; no other entries will be allowed in this range. The value 0 means that no flow-rule filter entries can be inserted in the filter by Diameter. If tIPv6FilterSharedPccRuleInsrtPt is set to 0 then tIPv6FilterSharedPccRuleInsrtSiz is also set to 0 by the system. Note that the range reserved for shared flow-rule entries must not overlap with that of either tIPv6FilterRadiusInsertPt/tIPv6FilterRadiusInsertSize, tIPv6FilterCreditCntrlInsertPt/tIPv6FilterCreditCntrlInsertSize, or tIPv6FilterHostSharedInsertPt/tIPv6FilterHostSharedInsertSize

OBJECT-TYPE

The value of the object tIPv6FilterSharedPccRuleNbrInsrt indicates how many flow-rule filter entries received from Diameter have been inserted in this filter

OBJECT-TYPE

The value of the object tIPv6FilterChainToSystemFilter specifies whether this filter policy is chained to the active IPv6 system filter policy. The active IPv6 system filter policy is defined as a row in tFilterSystemFilterTable that have the value of the object tFilterSystemFilterType set to 'fltrtypeselIpv6(4)'. The value 'true(1)' means this filter policy is chained to the active IPv6 system filter policy. The system filter policy's rules are executed first before any rules of this filter policy are executed. The value of this object can be set to 'true(1)' only when the scope of this policy (value of the object tIPv6FilterScope) is 'exclusive(1)' or 'template(2)'. The value 'false(2)' means this filter policy is not chained to the system filter policy.

OBJECT-TYPE

The value of the object tIPv6FilterType specifies the type of IPv6 filter.

OBJECT-TYPE

A table of all IPv6 filter match entries for all IPv6 filters

OBJECT-TYPE

Information about a particular IPv6 Filter entry. Every IPv6 Filter can have zero or more IPv6 Filter match entries. A filter entry with no match criteria set will match every packet, and the entry action will be taken. Entries are created/deleted by user. Additional match criteria can be found in tIPv6FilterParamsExtTable. There is no StorageType object, entries have a presumed StorageType of nonVolatile.

OBJECT-TYPE

This is the secondary index for the entry. Every IPv6 filter can have multiple entries, therefore every IPv6 filter entry is identified by the tIPv6FilterId and tIPv6FilterParamsIndex.

OBJECT-TYPE

This object allows entries to be created and deleted in the tIPv6FilterParamsTable.

OBJECT-TYPE

This object specifies the log to use for packets that match this entry. The value zero indicates that logging is disabled.

OBJECT-TYPE

User-provided description for this filter entry.

OBJECT-TYPE

The action to take for packets that match this filter entry. The value default(3) specifies this entry to inherit the behavior defined as the default for the filter. Setting the values 'forwardEsiL2' and 'forwardEsiL3' explicitly is ignored by the system. The values 'forwardEsiL2'(8) and 'forwardEsiL3'(9) can be set only implicitly by specifying non default values of objects specifying parameters for these actions. In such case the value of tIPFilterParamsAction will be set to 'forwardEsiL2'(8) or 'forwardEsiL3'(9) automatically by system. The object tIPv6FilterParamsAction supports only subset of filter actions. The object tIPvXFltrEntryActAction supports all actions. It's recommended to use tIPvXFltrEntryActAction instead of tIPv6FilterParamsAction. The following value(s) is(are) not supported: - reassemble

OBJECT-TYPE

The IPv6 address of the nexthop to which the packet should be forwarded if it hits this filter entry. The action of this entry should be 'forward' in such a case. Note that the value of tIPv6FilterParamsForwardNH is silently cleared by the system if tIPv6FilterParamsAction is set to value other than 'forward'(2), or any object related to 'forward' other than tIPv6FilterParamsForwardNH or tIPv6FilterParamsForwardNHIndirect or tIPv6FilterParamsFwdRtrId is set.

OBJECT-TYPE

tIPv6FilterParamsForwardNHIndirect specifies if the nexthop is directly or indirectly reachable. Note that the value of tIPv6FilterParamsForwardNHIndirect is silently cleared by the system if tIPv6FilterParamsAction is set to value other than 'forward'(2), or any object related to 'forward' other than tIPv6FilterParamsForwardNH, tIPv6FilterParamsForwardNHIndirect or tIPv6FilterParamsFwdRtrId is set.

OBJECT-TYPE

The DSCP value that should be remarked in case a packet hits this filter entry.

OBJECT-TYPE

tIPv6FilterParamsRemarkDSCPMask specifies the care bits while remarking with the DSCP value.

OBJECT-TYPE

tIPv6FilterParamsRemarkDot1p specifies the Dot1p value that needs to be remarked on the packet if it hits this filter entry.

OBJECT-TYPE

IPv6 address to match the source IPv6 address of the packet.

OBJECT-TYPE

If different from 0, the object tIPv6FilterParamsSourceIpMask specifies the IPv6 prefix length value for this policy IPv6 Filter entry. The mask generated from the prefix length value is ANDed with the received source IPv6 address to match the tIPv6FilterParamsSourceIpAddr. If the value of tIPv6FilterParamsSourceIpMask is 0, and the value of tIPv6FilterParamsSrcIpFullMask is non zero then the value of tIPv6FilterParamsSrcIpFullMask is used as a mask. If the value of tIPv6FilterParamsSourceIpMask is non zero, it will be equal to the mask expressed in the object tIPv6FilterParamsSrcIpFullMask. If both tIPv6FilterParamsSourceIpMask and tIPv6FilterParamsSrcIpFullMask are set to 0, no matching is done on the source IPv6 address. If a value is specified for this object, then the value of the object tIPv6FilterParamsSrcIpFullMask will be set to reflect this same mask.

OBJECT-TYPE

IPv6 address to match the destination IPv6 address of the packet.

OBJECT-TYPE

If different from 0, the object tIPv6FilterParamsDestinationIpMask specifies the IPv6 prefix length value for this policy IPv6 Filter entry. The mask generated from the prefix length value is ANDed with the received destination IPv6 address to match the tIPv6FilterParamsDestinationIpAddr. If the value of tIPv6FilterParamsDestinationIpMask is 0, and the value of tIPv6FilterParamsDstIpFullMask is non zero then the value of tIPv6FilterParamsDstIpFullMask is used as a mask. If the value of tIPv6FilterParamsDestinationIpMask is non zero, it will be equal to the mask expressed in the object tIPv6FilterParamsDstIpFullMask. If both tIPv6FilterParamsDestinationIpMask and tIPv6FilterParamsDstIpFullMask are set to 0, no matching is done on the destination IPv6 address. If a value is specified for this object, then the value of the object tIPv6FilterParamsDstIpFullMask will be set to reflect this same mask.

OBJECT-TYPE

IPv6 next header to match. Set to -1 to disable matching IPv6 next header. Because the match criteria only pertains to the last next-header, the following values are not accepted: 0, 43, 44, 50, 51, and 60.

OBJECT-TYPE

TCP/UDP port value1. The value of this object is used as per the description for tIPv6FilterParamsSourcePortOperator.

OBJECT-TYPE

TCP/UDP port value2. The value of this object is used as per the description for tIPv6FilterParamsSourcePortOperator.

OBJECT-TYPE

The operator specifies the manner in which tIPFilterParamsSourcePortValue1 and tIPFilterParamsSourcePortValue2 are to be used.

OBJECT-TYPE

TCP/UDP port value1. The value of this object is used as per the description for tIPv6FilterParamsDestPortOperator.

OBJECT-TYPE

TCP/UDP port value2. The value of this object is used as per the description for tIPv6FilterParamsDestPortOperator.

OBJECT-TYPE

The operator specifies the manner in which tIPFilterParamsDestPortValue1 and tIPFilterParamsDestPortValue2 are to be used.

OBJECT-TYPE

DSCP to be matched on the packet.

OBJECT-TYPE

If Enabled, matches a TCP Syn as per value of the object.

OBJECT-TYPE

If Enabled, matches a TCP Ack as per value of the object.

OBJECT-TYPE

ICMP code to be matched. The value -1 means ICMP code matching is not enabled.

OBJECT-TYPE

ICMP type to be matched. The value -1 means ICMP type matching is not enabled.

OBJECT-TYPE

When tIPFilterParamsCflowdSample has a value of 'true', Cflowd sampling and analysis is performed on those packet streams where this filter has been applied. Only packets matching this IPv6 filter entry are subjected to Cflowd sampling and analysis. A Cflowd profile controls the sampling and analysis of data flows through the router.

OBJECT-TYPE

When tIPv6FilterParamsCflowdIfSample has a value of 'true', Cflowd sampling and analysis is performed on those packet streams where this filter has been applied. Only packets matching this IPv6 filter entry are subjected to Cflowd sampling and analysis. A Cflowd profile controls the sampling and analysis of data flows through the router.

OBJECT-TYPE

The interface name for the nexthop to which the packet should be forwarded if it hits this filter entry. The action of this entry should be 'forward' in such a case. Note that the value of tIPv6FilterParamsForwardNHInterface is silently cleared by the system if tIPv6FilterParamsAction is set to value other than 'forward'(2), or any object related to 'forward' other than this one is set.

OBJECT-TYPE

This object indicates the number of times an ingress packet matched this entry.

OBJECT-TYPE

This object indicates the number of times an egress packet matched this entry.

OBJECT-TYPE

tIPv6FilterParamsLogInstantiated indicates if the filter log for this filter entry has been instantiated or not.

OBJECT-TYPE

tIPv6FilterParamsForwardRedPlcy specifies the redirect policy to be used to determine the nexthop. Note that the value of tIPv6FilterParamsForwardRedPlcy is silently cleared by the system if tIPv6FilterParamsAction is set to value other than 'forward'(2), or any object related to 'forward' other than this one is set.

OBJECT-TYPE

tIPv6FilterParamsActiveDest indicates the IPv6 address of the active destination for this IPv6 filter. A value of 0 indicates that there is currently no active destination.

OBJECT-TYPE

tIPv6FilterParamsTimeRangeName specifies the tmnxTimeRangeEntry to be associated with this filter entry. A value for this object can only be specified during row creation, and cannot be altered later on. Also, a value is accepted only if the tmnxTimeRangeEntry is defined in the TIMETRA-SCHEDULER-MIB::tmnxTimeRangeTable.tTimeRangeName. This object is obsoleted in release 14.0.

OBJECT-TYPE

tIPv6FilterParamsTimeRangeState indicates whether or not the entry is currently in effect. - timeRangeNotApplic: no time range is applicable for this entry. - timeRangeNotActive: A time range is defined in tIPv6FilterParamsTimeRangeName, but is not active at this moment. Consequently the filter entry is not installed. - timeRangeActive. A time range is defined in tIPv6FilterParamsTimeRangeName, and is activated successfully. - timeRangeActiveDownloadFailed: A time range is defined in tIPv6FilterParamsTimeRangeName, and is activated, but the corresponding filter entry could not be installed due to resource problems. This object is obsoleted in release 14.0.

OBJECT-TYPE

The value of tIPv6FilterParamsIngrHitByteCount indicates the number of bytes of all ingress packets that matched this entry.

OBJECT-TYPE

This tIPv6FilterParamsEgrHitByteCount indicates the number of bytes of all egress packets that matched this entry.

OBJECT-TYPE

tIPv6FilterParamsFwdSvcId indicates the service id of the destination for this filter entry. The value 0 indicates that there is no active SAP or SDP destination.

OBJECT-TYPE

tIPv6FilterParamsFwdSapPortId specifies the sap port id of the destination for this filter entry. The value 0 indicates that there is no SAP destination defined. A value different from 0 can only be specified if the value of the tIPv6FilterParamsAction object of this entry is 'forward'. In addition a non-zero value can only be given if the object tIPv6FilterParamsFwdSdpBind is '0'. Note that the value of tIPv6FilterParamsFwdSapPortId is silently cleared by the system if tIPv6FilterParamsAction is set to value other than 'forward'(2), or any object related to 'forward' other than tIPv6FilterParamsFwdSapPortId or tIPv6FilterParamsFwdSapEncapVal is set.

OBJECT-TYPE

tIPv6FilterParamsFwdSapEncapVal specifies the sap port encap value of the destination SAP for this filter entry. A value different from 0 can only be specified if the value of the tIPv6FilterParamsAction object of this entry is 'forward'. In addition a non-zero value can only be given if the object tIPv6FilterParamsFwdSdpBind has value '0'. The value 0 indicates that either 1) the sap encapsulation value is not specified when tIPv6FilterParamsFwdSapPortId and tIPv6FilterParamsFwdSvcId have valid values; or 2) that there is no SAP destination. Note that the value of tIPv6FilterParamsFwdSapEncapVal is silently cleared by the system if tIPv6FilterParamsAction is set to value other than 'forward'(2), or any object related to 'forward' other than tIPv6FilterParamsFwdSapPortId or tIPv6FilterParamsFwdSapEncapVal is set.

OBJECT-TYPE

tIPv6FilterParamsFwdSdpBind specifies the sdp bind id of the destination for this filter entry. The value '0' indicates that there is currently no SDP binding defined. A value different from '0' can only be specified if the value of the tIPv6FilterParamsAction object of this entry is 'forward'. In addition a non-zero value can only be given if the objects tIPv6FilterParamsFwdSapPortId and tIPv6FilterParamsFwdSapEncapVal have value 0. Note that the value of tIPv6FilterParamsFwdSdpBind is silently cleared by the system if tIPv6FilterParamsAction is set to value other than 'forward'(2), or any object related to 'forward' other than this one is set.

OBJECT-TYPE

The value of tIPv6FilterParamsRedirectURL specifies the URL to redirect to, when the value of tIPv6FilterParamsAction is 'httpRedirect'. The following macro substitutions are applicable in this context: $URL, $MAC, $IP, $SUB, $SAP, $SAPDESC, $CID, and $RID. Note that the value of tIPv6FilterParamsRedirectURL is silently cleared by the system if tIPv6FilterParamsAction is set to any value other than httpRedirect.

OBJECT-TYPE

The value of this object specifies the IPv6 prefix list used as match criterion for the source IPv6 address. The value specified for this object must correspond to a prefix list defined in tFilterPrefixListTable. If the value of this object is empty then the values of the objects tIPv6FilterParamsSourceIpAddr and tIPv6FilterParamsSourceIpMask are used as source IPv6 address match criterion. When this object is set to a non-empty value then the objects tIPv6FilterParamsSourceIpAddr and tIPv6FilterParamsSourceIpMask are reset to their default values by the system. Vice versa, when a new (non-default) value is provided for the objects tIPv6FilterParamsSourceIpAddr and tIPv6FilterParamsSourceIpMask then this object is reset to its default (empty) value by the system.

OBJECT-TYPE

The value of this object specifies the IPv6 prefix list used as match criterion for the destination IPv6 address. The value specified for this object must correspond to a prefix list defined in tFilterPrefixListTable. If the value of this object is empty then the values of the objects tIPv6FilterParamsDestinationIpAddr and tIPv6FilterParamsDestinationIpMask are used as destination ipv6 address match criterion. When this object is set to a non-empty value then the objects tIPv6FilterParamsDestinationIpAddr and tIPv6FilterParamsDestinationIpMask are reset to their default values by the system. Vice versa, when a new (non-default) value is provided for the objects tIPv6FilterParamsDestinationIpAddr and tIPv6FilterParamsDestinationIpMask then this object is reset to its default (empty) value by the system.

OBJECT-TYPE

If Enabled, matches fragmented/unfragmented packets as per value of the object.

OBJECT-TYPE

If Enabled, matches a Hop-By-Hop options Extension Header as per value of the object.

OBJECT-TYPE

If Enabled, matches a Routing Extension Header as per value of the object.

OBJECT-TYPE

This object specifies how the source port objects (tIPv6FilterParamsSourcePortValue1, tIPv6FilterParamsSourcePortValue2, tIPv6FilterParamsSourcePortOperator, tIPv6FilterParamsSrcPortList) and destination port objects (tIPv6FilterParamsDestPortValue1, tIPv6FilterParamsDestPortValue2, tIPv6FilterParamsDestPortOperator, tIPv6FilterParamsDstPortList) are combined to form the filter match criterion. See description of TFltrPortSelector.

OBJECT-TYPE

The value of this object specifies the port-list used as match criterion for the source port. The value specified for this object must correspond to a port-list defined in tFilterPortListTable. If the value of this object is empty then the values of the objects tIPFilterParamsSourcePortValue1, tIPFilterParamsSourcePortValue2, and tIPFilterParamsSourcePortOperator are used as source port match criterion. When this object is set to a non-empty value then the objects tIPFilterParamsSourcePortValue1, tIPFilterParamsSourcePortValue2, and tIPFilterParamsSourcePortOperator are reset to their default values by the system. Vice versa, when a new (non-default) value is provided for one of the objects tIPFilterParamsSourcePortValue1, tIPFilterParamsSourcePortValue2, or tIPFilterParamsSourcePortOperator then tIPv6FilterParamsSrcPortList is reset to its default (empty) value by the system. Setting any one of the objects tIPFilterParamsSourcePortValue1, tIPFilterParamsSourcePortValue2, or tIPFilterParamsSourcePortOperator to a non-default value in combination with a non-default value for the object tIPv6FilterParamsSrcPortList is rejected by the system

OBJECT-TYPE

The value of this object specifies the port-list used as match criterion for the destination port. The value specified for this object must correspond to a port-list defined in tFilterPortListTable. If the value of this object is empty then the values of the objects tIPFilterParamsDestPortValue1, tIPFilterParamsDestPortValue2, and tIPFilterParamsDestPortOperator are used as destination port match criterion. When this object is set to a non-empty value then the objects tIPFilterParamsDestPortValue1, tIPFilterParamsDestPortValue2, and tIPFilterParamsDestPortOperator are reset to their default values by the system. Vice versa, when a new (non-default) value is provided for one of the objects tIPFilterParamsDestPortValue1, tIPFilterParamsDestPortValue2, or tIPFilterParamsDestPortOperator then tIPv6FilterParamsDstPortList is reset to its default (empty) value by the system. Setting any one of the objects tIPFilterParamsDestPortValue1, tIPFilterParamsDestPortValue2, or tIPFilterParamsDestPortOperator to a non-default value in combination with a non-default value for the object tIPv6FilterParamsDstPortList is rejected by the system

OBJECT-TYPE

The value of this object specifies whether or not the value of tIPv6FilterParamsRedirectURL can be overridden by a Radius VSA. The default value is false (i.e. the URL cannot be overridden by Radius). The value of tIPv6FilterParamsRdirAllwRadOvrd is relevant only if the value of tIPv6FilterParamsAction is httpRedirect. Setting the value of tIPv6FilterParamsRdirAllwRadOvrd to true is ignored by the system if the value of tIPv6FilterParamsAction is not httpRedirect. Furthermore, the value of tIPv6FilterParamsRdirAllwRadOvrd is silently reset to false by the system if tIPv6FilterParamsAction is set to any value other than httpRedirect.

OBJECT-TYPE

tIPv6FilterParamsFwdRtrId specifies, if different from '0', the router id into which the packet should be forwarded if it hits this filter entry. The action of this entry should be 'forward' in such a case. Note that the value of tIPv6FilterParamsFwdRtrId is silently cleared by the system if tIPv6FilterParamsAction is set to value other than 'forward'(2), or any object related to 'forward' other than tIPv6FilterParamsFwdRtrId, tIPv6FilterParamsForwardNH or tIPv6FilterParamsForwardNHIndirect is set.

OBJECT-TYPE

If different from 0, the object tIPv6FilterParamsSrcIpFullMask specifies the IPv6 Mask value for this policy IPv6 Filter entry. The mask is ANDed with the received Source IPv6 address to match the tIPv6FilterParamsSourceIpAddr. If the value of tIPv6FilterParamsSourceIpMask is 0, and the value of tIPv6FilterParamsSrcIpFullMask is non zero then the value of tIPv6FilterParamsSrcIpFullMask is used as a mask. If the value of tIPv6FilterParamsSourceIpMask is non zero, it will be equal to the mask expressed in the object tIPv6FilterParamsSrcIpFullMask. If both tIPv6FilterParamsSourceIpMask and tIPv6FilterParamsSrcIpFullMask are set to 0, no matching is done on the Source IPv6 address. If a regular mask is specified for tIPv6FilterParamsSrcIpFullMask then the value of tIPv6FilterParamsSourceIpMask will be changed to reflect this value.

OBJECT-TYPE

If different from 0, the object tIPv6FilterParamsDstIpFullMask specifies the IPv6 Mask value for this policy IPv6 Filter entry. The mask is ANDed with the received Destination IPv6 address to match the tIPv6FilterParamsDestinationIpAddr. If the value of tIPv6FilterParamsDestinationIpMask is 0, and the value of tIPv6FilterParamsDstIpFullMask is non zero then the value of tIPv6FilterParamsDstIpFullMask is used as a mask. If the value of tIPv6FilterParamsDestinationIpMask is non zero, it will be equal to the mask expressed in the object tIPv6FilterParamsDstIpFullMask. If both tIPv6FilterParamsDestinationIpMask and tIPv6FilterParamsDstIpFullMask are set to 0, no matching is done on the Destination IPv6 address. If a regular mask is specified for tIPv6FilterParamsDstIpFullMask then the value of tIPv6FilterParamsDestinationIpMask will be changed to reflect this value.

OBJECT-TYPE

The value of this object specifies the name of the NAT policy to be used when the value of tIPv6FilterParamsAction is nat. If the value is empty then a default policy is used. If the value is non-empty then it must correspond to a policy defined in tmnxNatPlcyTable. The value of tIPv6FilterParamsNatPolicyName is relevant only if the value of tIPv6FilterParamsAction is nat. Setting the value of tIPv6FilterParamsNatPolicyName to a non-empty string is ignored by the system if the value of tIPv6FilterParamsAction is not nat. Furthermore, the value of tIPv6FilterParamsNatPolicyName is silently reset to an empty string by the system if tIPv6FilterParamsAction is set to any value other than nat.

OBJECT-TYPE

If different from -1 the value of the object tIPv6FilterParamsFlowLabel specifies the flow label to be used as a match criterion.

OBJECT-TYPE

The value of the object tIPv6FilterParamsFlowLabelMask specifies the flow label mask value for this policy IP Filter entry. The mask is ANDed with the received flow label to match the value of the object tIPv6FilterParamsFlowLabel. The value is only significant if the value of the object tIPv6FilterParamsFlowLabel is different from -1.

OBJECT-TYPE

If different from zero the value of the object tIPv6FilterParamsFwdLsp together with the value of the object tIPv6FilterParamsFwdLspRtrId specifies the LSP into which a packet should be forwarded if it hits this filter entry. The value of the object tIPv6FilterParamsAction of this entry must be 'forward' in such case. Otherwise the value of the object tIPv6FilterParamsFwdLsp is ignored by the system. The value is reset to '0' if the value of the object tIPv6FilterParamsAction is set to value other than 'forward'(2), or any object related to 'forward' other than tIPv6FilterParamsFwdLspRtrId or tIPv6FilterParamsFwdLsp is set. The value of the object tIPv6FilterParamsFwdLsp cannot be set to a non-zero value if other destinations are already specified. The value has to be '0' if the value of the object tIPv6FilterParamsFwdLspRtrId is not set (i.e. is '0'). If a non-zero value is set, the value of the object tIPv6FilterParamsFwdLspRtrId has to be set as well.

OBJECT-TYPE

The value of the object tIPv6FilterParamsFwdLspRtrId specifies the router ID that the LSP ID defined by the value of the object tIPv6FilterParamsFwdLsp belongs to. The value of the object tIPv6FilterParamsAction of this entry must be 'forward' in such case. Otherwise the value of the object tIPv6FilterParamsFwdLspRtrId is ignored by the system. The value is reset to '0' if the value of the object tIPv6FilterParamsAction is set to other value than 'forward'(2), or any object related to 'forward' other than tIPv6FilterParamsFwdLspRtrId or tIPv6FilterParamsFwdLsp is set. The value of this object cannot be set to a non-zero value if other destinations are already specified. The value has to be '0' if the value of the object tIPv6FilterParamsFwdLsp is not set (i.e. is '0'). If a non-zero value is set, the value of the object tIPv6FilterParamsFwdLsp has to be set as well. The ID of the base router and '0' are the only allowed values with this version of the product.

OBJECT-IDENTITY

OBJECT-TYPE

tFltrGrpInsrtdEntriesFilterType specifies the type of the filter referred to by tFltrGrpInsrtdEntriesFilterId. Inserted entries can only occur in 'fltrtypeselIp' and 'fltrtypeselIpv6'

OBJECT-TYPE

tFltrGrpInsrtdEntriesFilterId specifies for which filter the inserted entries must be grouped.

OBJECT-TYPE

tFltrGrpInsrtdEntriesApplication specifies for which application the inserted entries must be grouped.

OBJECT-TYPE

tFltrGrpInsrtdEntriesLocation specifies at what location the inserted entries must be grouped.

OBJECT-TYPE

tFltrGrpInsrtdEntriesResult indicates the success or failure of the last requested grouping request on inserted entries.

OBJECT-TYPE

tFltrGrpInsrtdEntriesFeedback may indicate additional info on the last inserted filter entries grouping action performed.

OBJECT-TYPE

Setting the object tFltrGrpInsrtdEntriesExecute to 'true' will cause the system to attempt to execute the grouping command as specified by the other MIB objects in the tFilterGroupInsertedEntries mibgroup. When read the value will always indicate 'false'. The result of the command can be found in tFltrGrpInsrtdEntriesResult and tFltrGrpInsrtdEntriesFeedback

OBJECT-TYPE

The value of tDhcpFilterTableLastChanged indicates the sysUpTime at the time of the last modification to tDhcpFilterTable by adding, deleting an entry or change to a writable object in the table. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

Contains a list of all DHCP filters configured on this system.

OBJECT-TYPE

Information about a particular DHCP filter. Entries are created/deleted by user. Entries have a presumed StorageType of nonVolatile.

OBJECT-TYPE

Uniquely identifies a DHCP filter as configures on this system.

OBJECT-TYPE

This object allows entries to be created and deleted in the tDhcpFilterTable.

OBJECT-TYPE

The value of tDhcpFilterLastChanged indicates the timestamp of last change to this row in tDhcpFilterTable.

OBJECT-TYPE

User-provided description for this filter.

OBJECT-TYPE

The default action to take for DHCP host creation requests that do not match any of this filter's entries. The value none(1) specifies normal host creation behaviour, the value bypass-host-creation(2) specifies to bypass host creation, the value drop(3) specifies to drop the DHCP message.

OBJECT-TYPE

The value of tDhcpFilterParamsTblLastChanged indicates the sysUpTime at the time of the last modification to tDhcpFilterParamsTable by adding, deleting an entry or change to a writable object in the table. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

A table of all DHCP filter match entries for all DHCP filters

OBJECT-TYPE

Information about a particular DHCP filter entry. Every DHCP filter can have zero or more DHCP filter match entries. A filter entry with no match criteria set will match every packet, and the entry action will be taken. Entries are created/deleted by user. There is no StorageType object, entries have a presumed StorageType of nonVolatile.

OBJECT-TYPE

This is the secondary index for the entry. Every DHCP filter can have multiple entries, therefore every DHCP filter entry is identified by the tDhcpFilterId and tDhcpFilterParamsId.

OBJECT-TYPE

This object allows entries to be created and deleted in the tDhcpFilterParamsTable.

OBJECT-TYPE

The value of tDhcpFilterParamsLastChanged indicates the timestamp of last change to this row in tDhcpFilterParamsTable.

OBJECT-TYPE

The value of tDhcpFilterParamsOptionNumber specifies the number of the DHCP option to filter on.

OBJECT-TYPE

The value of tDhcpFilterParamsOptionMatch specifies the criteria that the DHCP option must match to trigger this filter entry. The value present(1) specifies that the DHCP option must be present, the value absent(2) specifies that the DHCP option must be absent. In these cases tDhcpFilterParamsOptionValue will be reset to an empty string. A value string(3), string-exact(4), string-invert(5), string-exact-invert(6), hex(7), hex-exact(8), hex-invert(9) or hex-exact-invert(10) requires an octet string to be present in tDhcpFilterParamsOptionValue to match against.

OBJECT-TYPE

The action to take for DHCP host creation requests that match this filter entry. The value none(1) specifies normal host creation behaviour, the value bypass-host-creation(2) specifies to bypass host creation, the value drop(3) specifies to drop the DHCP message.

OBJECT-TYPE

The value of the object tDhcpFilterParamsOptionValue specifies the matching pattern for the filtered DHCP option. This object is mandatory at creation time. A zero length value is only allowed when the value of tDhcpFilterParamsOptionMatch is present(1) or absent(2).

OBJECT-TYPE

The value of tMacFilterNameTableLastChgd indicates the sysUpTime at the time of the last modification of tMacFilterNameTable. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

A table that contains MAC filter name information. Entries are created automatically by the system when tMacFilterName object is set for the MAC filter.

OBJECT-TYPE

Basic information about a specific MAC filter name.

OBJECT-TYPE

The value of the object tMacFilterNameId indicates the filter name associated with this MAC filter.

OBJECT-TYPE

This value of the object tMacFilterNameRowStatus indicates the status of this row.

OBJECT-TYPE

The value of tMacFilterNameLastChanged indicates the sysUpTime at the time of the last modification of this entry. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The value of tIpFilterNameTableLastChgd indicates the sysUpTime at the time of the last modification of tIpFilterNameTable. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

A table that contains IP filter name information. Entries are created automatically by the system when tIpFilterName object is set for the IP filter.

OBJECT-TYPE

Basic information about a specific IP filter name.

OBJECT-TYPE

The value of the object tIpFilterNameId indicates the filter name associated with this IP filter.

OBJECT-TYPE

This value of the object tIpFilterNameRowStatus indicates the status of this row.

OBJECT-TYPE

The value of tIpFilterNameLastChanged indicates the sysUpTime at the time of the last modification of this entry. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The value of tIpv6FilterNameTableLastChgd indicates the sysUpTime at the time of the last modification of tIpv6FilterNameTable. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

A table that contains IPv6 filter name information. Entries are created automatically by the system when tIpv6FilterName object is set for the IPv6 filter.

OBJECT-TYPE

Basic information about a specific IPv6 filter name.

OBJECT-TYPE

The value of the object tIpv6FilterNameId indicates the filter name associated with this IPv6 filter.

OBJECT-TYPE

This value of the object tIpv6FilterNameRowStatus indicates the status of this row.

OBJECT-TYPE

The value of tIpv6FilterNameLastChanged indicates the sysUpTime at the time of the last modification of this entry. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-IDENTITY

OBJECT-TYPE

The object tLiReservedBlockTableLastChanged indicates the sysUpTime at the time of the last modification of tLiReservedBlockTable. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The table tLiReservedBlockTable describes LI reserved blocks. In this release this table can have at most one entry.

OBJECT-TYPE

Information about an LI reserved block. This block can be associated with one or more filters to reserve a number of entries in those filters for LI.

OBJECT-TYPE

The object tLiReservedBlockName uniquely identifies an LI reserved block.

OBJECT-TYPE

The object tLiReservedBlockRowStatus specifies the status of this row.

OBJECT-TYPE

The object tLiReservedBlockLastChanged indicates the sysUpTime at the time of the last modification of this entry. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The object tLiReservedBlockDescription specifies a description for this LI reserved block.

OBJECT-TYPE

The object tLiReservedBlockStart specifies the starting entry of the LI reserved block. If set to '0' no block is reserved. In this case the value of the object tLiReservedBlockSize will be set to '0' by the system.

OBJECT-TYPE

The object tLiReservedBlockSize specifies the size of the LI reserved block. If set to '0' no block is reserved. In this case the value of the object tLiReservedBlockStart will be set to '0' by the system. The maximum value of this object may be limited depending on hardware variants.

OBJECT-TYPE

The value of tLiReservedBlockFltrTableLastChg indicates the sysUpTime at the time of the last modification of tLiReservedBlockFltrTable. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The table tLiReservedBlockFltrTable contains associations between normal filters and LI block reservations. Setting the value of TIMETRA_SYSTEM_MIB:tmnxSysMgmtIfWriteMode to VAL_tmnxSysMgmtIfWriteOperMode_mixed won't be allowed if this table contains reference to non existing filter. Before enabling mixed mode the loose references should be removed or replaced by name references in tLiRsvdBlockFltrAssocTable

OBJECT-TYPE

An association of a normal filter with an LI block reservation. In this release MAC and IP/IPv6 filters are supported. Entries can be created and deleted via SNMP SET operations to tLiReservedBlockFltrRowStatus.

OBJECT-TYPE

The object tLiReservedBlockFltrType specifies the type of filter this LI block reservation applies to. In this release MAC and IP/IPv6 filters are supported: fltrtypeselIp (1) fltrtypeselMac (2) fltrtypeselIpv6 (4)

OBJECT-TYPE

The object tLiReservedBlockFltrIdStart specifies the ID of the first filter to apply an LI block reservation. If the value of the object tLiReservedBlockFltrType is equal to 1 or 4 (IP or IPv6 filter) then the scope of any filter (defined by the value of the object tIPFilterScope or tIPv6FilterScope) inside of the range defined by the values of the objects tLiReservedBlockFltrIdStart and tLiReservedBlockFltrIdEnd must not be equal to embedded (3). In this release, tLiReservedBlockFltrIdStart must be equal to tLiReservedBlockFltrIdEnd.

OBJECT-TYPE

The object tLiReservedBlockFltrIdEnd specifies the ID of the last filter to apply an LI block reservation. If the value of the object tLiReservedBlockFltrType is equal to 1 or 4 (IP or IPv6 filter) then the scope of any filter (defined by the value of the object tIPFilterScope or tIPv6FilterScope) inside of the range defined by the values of the objects tLiReservedBlockFltrIdStart and tLiReservedBlockFltrIdEnd must not be equal to embedded (3). In this release, tLiReservedBlockFltrIdEnd must be equal to tLiReservedBlockFltrIdStart.

OBJECT-TYPE

The object tLiReservedBlockFltrRowStatus specifies the status of this row.

OBJECT-TYPE

The object tLiReservedBlockFltrLastChanged indicates the sysUpTime at the time of the last modification of this entry. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The object tLiFilterTableLastChanged indicates the sysUpTime at the time of the last modification of tLiFilterTable. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The table tLiFilterTable contains information about all LI filters. In this release MAC and IP/IPv6 filters are supported.

OBJECT-TYPE

Each entry represents an LI filter. In this release MAC and IP/IPv6 filters are supported. Entries can be created and deleted via SNMP SET operations to tLiFilterRowStatus.

OBJECT-TYPE

The object tLiFilterType specifies the type of this LI filter. In this release MAC and IP/IPv6 filters are supported.

OBJECT-TYPE

The object tLiFilterName indicates the unique name of this LI Filter.

OBJECT-TYPE

The object tLiFilterRowStatus specifies the status of this row.

OBJECT-TYPE

The object tLiFilterLastChanged indicates the sysUpTime at the time of the last modification of this entry. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The object tLiFilterDescription specifies a description for this LI filter.

OBJECT-TYPE

The object tLiFilterAssociationTableLastChg indicates the sysUpTime at the time of the last modification of tLiFilterAssociationTable. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The table tLiFilterAssociationTable contains information about the associations between LI filters and normal filters.

OBJECT-TYPE

An association between an LI filter and a normal filter.

OBJECT-TYPE

The object tLiFilterAssociationFltrId indicates the id of the normal filter in the association described by this entry.

OBJECT-TYPE

The object tLiFilterAssociationRowStatus specifies the status of this row.

OBJECT-TYPE

The object tLiFilterAssociationLastChg indicates the sysUpTime at the time of the last modification of this entry. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The object tLiMacFilterParamsTableLastChg indicates the sysUpTime at the time of the last modification of tLiMacFilterParamsTable. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The table tLiMacFilterParamsTable contains all LI MAC filter match entries for all LI MAC filters.

OBJECT-TYPE

An LI MAC filter match entry.

OBJECT-TYPE

The object tLiMacFilterParamsId indicates the secondary index for this entry. Every LI MAC filter may have multiple match entries, therefore every LI MAC filter match entry is identified by the tLiFilterName and tLiMacFilterParamsId.

OBJECT-TYPE

The object tLiMacFilterParamsRowStatus specifies the status of this row.

OBJECT-TYPE

The object tLiMacFilterParamsLastChanged indicates the sysUpTime at the time of the last modification of this entry. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The object tLiMacFilterParamsDescription specifies a description for this entry.

OBJECT-TYPE

The object tLiMacFilterParamsFrameType specifies the type of mac frame for which we are defining this match criterion.

OBJECT-TYPE

The object tLiMacFilterParamsSrcMAC specifies the source MAC address to match for this LI MAC filter entry.

OBJECT-TYPE

The object tLiMacFilterParamsSrcMACMask specifies the source MAC mask value for this LI MAC filter match entry. The mask is ANDed with the MAC to match tLiMacFilterParamsSrcMAC. A cleared bit means ignore this bit, do not match. A set bit means match this bit with tLiMacFilterParamsSrcMAC. Use the value 00-00-00-00-00-00 to disable this filter criterion. If set to all zero, the value of tLiMacFilterParamsSrcMAC will be set to all zero by the system, and any attempt to change this value will be ignored.

OBJECT-TYPE

The object tLiMacFilterParamsDstMAC specifies the destination MAC to match for this LI MAC filter entry.

OBJECT-TYPE

The object tLiMacFilterParamsDstMACMask specifies the destination MAC mask value for this LI MAC filter match entry. The mask is ANDed with the MAC to match tLiMacFilterParamsDstMAC. A cleared bit means ignore this bit, do not match. A set bit means match this bit with tLiMacFilterParamsDstMAC. Use the value 00-00-00-00-00-00 to disable this filter criteria. If set to all zero, the value of tLiMacFilterParamsDstMAC will be set to all zero by the system, and any attempt to change this value will be ignored.

OBJECT-TYPE

The object tLiMacFilterParamsIngrHitCount indicates the number of times an ingress packet matched this entry.

OBJECT-TYPE

This object tLiMacFilterParamsEgrHitCount indicates the number of times an egress packet matched this entry.

OBJECT-TYPE

The value of tLiMacFilterParamsIngrHitBytes indicates the number of bytes of all ingress packets that matched this entry.

OBJECT-TYPE

The value of tLiMacFilterParamsEgrHitBytes indicates the number of bytes of all egress packets that matched this entry.

OBJECT-TYPE

The value of the object tLiIpFilterParamsTableLastChg indicates the sysUpTime at the time of the last modification of tLiIpFilterParamsTable. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The table tLiIpFilterParamsTable contains information pertaining to match entries of LI IP/IPv6 filters.

OBJECT-TYPE

Each entry represents a configuration of an LI IP/IPv6 filter entry. Entries can be created and deleted via SNMP SET operations to tLiIpFilterParamsRowStatus.

OBJECT-TYPE

The value of the object tLiIpFilterParamsId indicates the tertiary index for tLiIpFilterParamsEntry. Every LI IP filter may have multiple match entries therefore every entry is identified by the values of tLiFilterType, tLiFilterName and tLiIpFilterParamsId.

OBJECT-TYPE

The value of the object tLiIpFilterParamsLastChanged indicates the sysUpTime at the time of the last modification of this entry. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The value of the object tLiIpFilterParamsRowStatus specifies the status of this row in tLiIpFilterParamsTable.

OBJECT-TYPE

The value of the object tLiIpFilterParamsDescription specifies the description for this LI IP filter entry.

OBJECT-TYPE

The value of the object tLiIpFilterParamsSrcIpAddrType specifies the context in which the values of the objects tLiIpFilterParamsSrcIpAddr and tLiIpFilterParamsSrcIpFullMask are interpreted. Only following values are supported: unknown(0) ipv4(1) ipv6(2) Furthermore the value must be consistent with the filter type given by the value of the index object tLiFilterType. If the value of this object is set to 'unknown' then the values of the objects tLiIpFilterParamsSrcIpAddr and tLiIpFilterParamsSrcIpFullMask are automatically set to their default values.

OBJECT-TYPE

The value of the object tLiIpFilterParamsSrcIpAddr specifies the source IP address to be matched by this LI IP filter entry. The value must be consistent with the IP version value of the associated tLiIpFilterParamsSrcIpAddrType object. If the value of the object tLiIpFilterParamsSrcIpAddrType is set to 'unknown' then the value of this object is automatically set to the default value.

OBJECT-TYPE

The value of the object tLiIpFilterParamsSrcIpFullMask specifies the IP mask value that is ANDed with the received source IP address to match the value in tLiIpFilterParamsSrcIpAddr. The value must be consistent with the IP version value of the associated tLiIpFilterParamsSrcIpAddrType object and must not be equal to zero. If the value of the object tLiIpFilterParamsSrcIpAddrType is set to 'unknown' then the value of this object is automatically set to the default value.

OBJECT-TYPE

The value of the object tLiIpFilterParamsDstIpAddrType specifies the context in which the values of the objects tLiIpFilterParamsDstIpAddr and tLiIpFilterParamsDstIpFullMask are interpreted. Only following values are supported: unknown(0) ipv4(1) ipv6(2) Furthermore the value must always be consistent with the filter type given by the value of the index object tLiFilterType. If the value of this object is set to 'unknown' then the values of the objects tLiIpFilterParamsDstIpAddr and tLiIpFilterParamsDstIpFullMask are automatically set to their default values.

OBJECT-TYPE

The value of the object tLiIpFilterParamsDstIpAddr specifies the destination IP address to be matched by this LI IP filter entry. The value must be consistent with the IP version value of the associated tLiIpFilterParamsDstIpAddrType object. If the value of the object tLiIpFilterParamsDstIpAddrType is set to 'unknown' then the value of this object is automatically set to the default value.

OBJECT-TYPE

The value of the object tLiIpFilterParamsDstIpFullMask specifies the IP mask value that is ANDed with the received destination IP address to match the value in tLiIpFilterParamsDstIpAddr. The value must be consistent with the IP version value of the associated tLiIpFilterParamsDstIpAddrType object and must not be equal to zero. If the value of the object tLiIpFilterParamsDstIpAddrType is set to 'unknown' then the value of this object is automatically set to the default value.

OBJECT-TYPE

The value of the object tLiIpFilterParamsProtocolNextHdr specifies (depending on the filter type defined by the value of the object tLiFilterType) the IP protocol / IPv6 next-header value to be matched by this LI IP filter entry. The value must be set to -1 to disable the protocol / next-header matching. Because the match criteria only pertains to the last next-header, the following values are not accepted as IPv6 next-header values: 0, 43, 44, 50, 51, and 60.

OBJECT-TYPE

The value of the object tLiIpFilterParamsSrcPortValue1 specifies the TCP/UDP source port value1. It is used as per the description of tLiIpFilterParamsSrcPortOper.

OBJECT-TYPE

The value of the object tLiIpFilterParamsSrcPortValue2 specifies the TCP/UDP source port value2. It is used as per the description of tLiIpFilterParamsSrcPortOper.

OBJECT-TYPE

The value of the object tLiIpFilterParamsSrcPortOper specifies the manner in which tLiIpFilterParamsSrcPortValue1 and tLiIpFilterParamsSrcPortValue2 are to be used. The values of these latter 2 objects and tLiIpFilterParamsSrcPortOper are used as per the description of TTcpUdpPortOperator.

OBJECT-TYPE

The value of the object tLiIpFilterParamsDstPortValue1 specifies the TCP/UDP destination port value1. It is used as per the description of tLiIpFilterParamsDstPortOper.

OBJECT-TYPE

The value of the object tLiIpFilterParamsDstPortValue2 specifies the TCP/UDP destination port value2. It is used as per the description of tLiIpFilterParamsDstPortOper.

OBJECT-TYPE

The value of the object tLiIpFilterParamsDstPortOper specifies the manner in which tLiIpFilterParamsDstPortValue1 and tLiIpFilterParamsDstPortValue2 are to be used. The values of these latter 2 objects and tLiIpFilterParamsDstPortOper are used as per the description in TTcpUdpPortOperator.

OBJECT-TYPE

If enabled, matches fragmented/unfragmented packets as per value of the object. The fragment match criterion is not supported for IPv6 filter.

OBJECT-TYPE

The table tLiIpFilterParamsInfoTable contains read-only information pertaining to LI IP filter match entries of LI IP filters.

OBJECT-TYPE

This row complements the corresponding row in the tLiIpFilterParamsTable with read-only operational info. Entries are created and deleted automatically by the system when a corresponding entry in tLiIpFilterParamsTable is created / deleted.

OBJECT-TYPE

The value of the object tLiIpFltrParamsInfIngrHitCount indicates the number of times an ingress packet matched this entry.

OBJECT-TYPE

The value of the object tLiIpFltrParamsInfEgrHitCount indicates the number of times an egress packet matched this entry.

OBJECT-TYPE

The value of the object tLiIpFltrParamsInfIngrHitBytes indicates the number of bytes of all ingress packets that matched this entry.

OBJECT-TYPE

The value of the object tLiIpFltrParamsInfEgrHitBytes indicates the number of bytes of all egress packets that matched this entry.

OBJECT-TYPE

The value of tLiRsvdBlockFltrAssocTableLChg indicates the sysUpTime at the time of the last modification of tLiRsvdBlockFltrAssocTable. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The table tLiRsvdBlockFltrAssocTable contains associations between normal filters and LI block reservations. The tLiRsvdBlockFltrAssocTable associates filters by filter name in the contrast with tLiReservedBlockFltrTable which contains associations via filter id.

OBJECT-TYPE

An association of a normal filter with an LI block reservation. In this release MAC, IP and IPv6 filters are supported.

OBJECT-TYPE

The object tLiRsvdBlockFltrAssocFltrType specifies the type of filter this LI block reservation applies to. In this release MAC and IP/IPv6 filters are supported: fltrtypeselIp (1) fltrtypeselMac (2) fltrtypeselIpv6 (4)

OBJECT-TYPE

The object tLiRsvdBlockFltrAssocFltrName specifies the ID of the filter associated with this LI reserved block. The scope of associated filter (tIPFilterScope, tIPv6FilterScope, tMacFilterScope) must not equal to embedded(3).

OBJECT-TYPE

The object tLiRsvdBlockFltrAssocRowStatus specifies the status of this row.

OBJECT-TYPE

The object tLiRsvdBlockFltrAssocLastChanged indicates the sysUpTime at the time of the last modification of this entry. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The object tLiFilterAssociationTableLastChg indicates the sysUpTime at the time of the last modification of tLiFltrAssocFltrNameTable. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The table tLiFltrAssocFltrNameTable contains information about the associations between LI filters and normal filters.

OBJECT-TYPE

An association between an LI filter and a normal filter.

OBJECT-TYPE

The object tLiFltrAssocFltrName indicates the name of the normal filter in the association described by this entry.

OBJECT-TYPE

The object tLiFltrAssocFltrNameRowStatus specifies the status of this row.

OBJECT-TYPE

The object tLiFltrAssocFltrNameLastChg indicates the sysUpTime at the time of the last modification of this entry. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The object tFilterPrefixListTableLstChng indicates the sysUpTime at the time of the last modification of tFilterPrefixListTable. If no changes were made to the table since the last re-initialization of the local network management subsystem, this object contains the value zero.

OBJECT-TYPE

The table tFilterPrefixListTable contains an entry for each prefix list defined in the filter area.

OBJECT-TYPE

An entry in the tFilterPrefixListTable.

OBJECT-TYPE

The object tFilterPrefixListType specifies the type of prefix list for the prefix list tFilterPrefixListName.

OBJECT-TYPE

The object tFilterPrefixListName specifies the name given to this prefix list.

OBJECT-TYPE

The object tFilterPrefixListRowStatus specifies the status of this row.

OBJECT-TYPE

The object tFilterPrefixListLastChanged indicates the sysUpTime at the time of the last modification of this row. If no changes were made to the row since the last re-initialization of the local network management subsystem, then this object contains the value zero.

OBJECT-TYPE

The object tFilterPrefixListDescription specifies a description for this row.

OBJECT-TYPE

The object tFilterPrefixListEntryTblLstChg indicates the sysUpTime at the time of the last modification of tFilterPrefixListEntryTable. If no changes were made to the table since the last re-initialization of the local network management subsystem, this object contains the value zero.

OBJECT-TYPE

The table tFilterPrefixListEntryTable contains information pertaining to explicitly created prefixes in any prefix list defined in the filter area.

OBJECT-TYPE

An entry in the tFilterPrefixListEntryTable.

OBJECT-TYPE

The object tFilterPrefixListEntryPrefixType specifies whether the prefix specified in tFilterPrefixListEntryPrefix is an IPv4 or IPv6 prefix. The value of tFilterPrefixListEntryPrefixType must match the value of the object tFilterPrefixListType.

OBJECT-TYPE

The value of tFilterPrefixListEntryPrefix specifies the IP prefix of this prefix list entry.

OBJECT-TYPE

The value of tFilterPrefixListEntryPrefixLen specifies the IP prefix length of this prefix list entry.

OBJECT-TYPE

The object tFilterPrefixListEntryRowStatus specifies the status of this row.

OBJECT-TYPE

The object tFilterEmbeddedRefTableLstChg indicates the sysUpTime at the time of the last modification of tFilterEmbeddedRefTable. If no changes were made to the table since the last re-initialization of the local network management subsystem, this object contains the value zero.

OBJECT-TYPE

The table tFilterEmbeddedRefTable contains an entry for each embedded filter inserted in a filter with scope other than 'embedded'.

OBJECT-TYPE

An entry in the tFilterEmbeddedRefTable.

OBJECT-TYPE

The object tFilterEmbeddedRefFilterType specifies the type of filter for the filters specified by tFilterEmbeddedRefEmbeddedFltrId and tFilterEmbeddedRefInsertFltrId.

OBJECT-TYPE

The value of tFilterEmbeddedRefInsertFltrId specifies the filter where the filter specified by tFilterEmbeddedRefEmbeddedFltrId is to be inserted.

OBJECT-TYPE

The value of tFilterEmbeddedRefEmbeddedFltrId specifies the id of the filter to be inserted in the filter specified by tFilterEmbeddedRefInsertFltrId.

OBJECT-TYPE

The value of tFilterEmbeddedRefOffset specifies the offset of inserted entries.

OBJECT-TYPE

The object tFilterEmbeddedRefRowStatus specifies the status of this row.

OBJECT-TYPE

The value of tFilterEmbeddedRefAdminState specifies the administrative state of the embed request defined by this row. If an active embedding cannot be fulfilled due to dynamic events, this object will be set to 'inactive' automatically by the system. In those cases, the object tFilterEmbeddedRefOperState will indicate the failure reason.

OBJECT-TYPE

The value of tFilterEmbeddedRefOperState indicates the operational state of the embed request defined by this row.

OBJECT-TYPE

The value of tFilterEmbeddedRefLastChanged indicates the sysUpTime at the time of last change to this row in tFilterEmbeddedRefTable.

OBJECT-TYPE

The object tFilterPortListTableLstChng indicates the sysUpTime at the time of the last modification of tFilterPortListTable. If no changes were made to the table since the last re-initialization of the local network management subsystem, this object contains the value zero.

OBJECT-TYPE

The table tFilterPortListTable contains an entry for each port list defined in the filter area.

OBJECT-TYPE

An entry in the tFilterPortListTable.

OBJECT-TYPE

The object tFilterPortListName specifies the name given to this port list.

OBJECT-TYPE

The object tFilterPortListRowStatus specifies the status of this row.

OBJECT-TYPE

The object tFilterPortListLastChanged indicates the sysUpTime at the time of the last modification of this row. If no changes were made to the row since the last re-initialization of the local network management subsystem, then this object contains the value zero.

OBJECT-TYPE

The object tFilterPortListDescription specifies a description for this row.

OBJECT-TYPE

The object tFilterPortListEntryTblLstChg indicates the sysUpTime at the time of the last modification of tFilterPortListEntryTable. If no changes were made to the table since the last re-initialization of the local network management subsystem, this object contains the value zero.

OBJECT-TYPE

The table tFilterPortListEntryTable contains an entry for each port defined in any port list defined in the filter area.

OBJECT-TYPE

Specifies an entry in the tFilterPortListEntryTable. Two entries for the same port list must not overlap.

OBJECT-TYPE

This object specifies the lower value for the TCP/UDP port range. A value assigned to this object must be less than or equal to the value assigned to the corresponding object tFilterPortListEntryPortHigh.

OBJECT-TYPE

This object specifies the higher value for the TCP/UDP port range. A value assigned to this object must be greater than or equal to the value assigned to the corresponding object tFilterPortListEntryPortLow.

OBJECT-TYPE

The object tFilterPortListEntryRowStatus specifies the status of this row.

OBJECT-TYPE

The object tFilterApplyPathTableLstChng indicates the sysUpTime at the time of the last modification of tFilterApplyPathTable. If no changes were made to the table since the last re-initialization of the local network management subsystem, this object contains the value zero.

OBJECT-TYPE

The table tFilterApplyPathTable contains an entry for each apply-path rule defined in a prefix list.

OBJECT-TYPE

An entry in the tFilterApplyPathTable describing an apply-path rule. If an address or prefix configured by the source specified by tFilterApplyPathSource matches the conditions specified by tFilterApplyPathMatch1 and tFilterApplyPathMatch2, a prefix is inserted into the prefix list where this apply-path rule refers to.

OBJECT-TYPE

The object tFilterApplyPathSource specifies the source of the prefixes that will be generated by this apply-path rule.

OBJECT-TYPE

The object tFilterApplyPathIndex specifies an index for this row.

OBJECT-TYPE

The object tFilterApplyPathRowStatus specifies the status of this row.

OBJECT-TYPE

The object tFilterApplyPathLastChanged indicates the timestamp of the last change to this row.

OBJECT-TYPE

The object tFilterApplyPathMatch1 specifies a regular expression. The usage of this object depends on the source specified by tFilterApplyPathSource. If tFilterApplyPathSource is 'bgp-peers', this object specifies a match condition on the group-name of configured bgp peers.

OBJECT-TYPE

The object tFilterApplyPathMatch2 specifies a regular expression. The usage of this object depends on the source specified by tFilterApplyPathSource. If tFilterApplyPathSource is 'bgp-peers', this object specifies a match condition on the ip or IPv6 address of configured bgp peers.

OBJECT-TYPE

The value of the object tFilterApplyPathVRtrId specifies virtual router instance. The usage of this object depends on the source specified by tFilterApplyPathSource. If tFilterApplyPathSource is 'bgp-peers' then prefixes generated by apply-path rule will consist of bgp-peers pertaining to virtual router instance specified by this object.

OBJECT-TYPE

The table tFilterEmbeddedRefInfoTable contains an entry for each embedded filter inserted in a filter with scope other than 'embedded'. This row complements the corresponding row in the tFilterEmbeddedRefTable with read-only operational info.

OBJECT-TYPE

An entry in the tFilterEmbeddedRefInfoTable.

OBJECT-TYPE

The value of tFltrEmbedRefInfEntryCnt indicates how many entries are present in the embedded filter as specified in tFilterEmbeddedRefEmbeddedFltrId.

OBJECT-TYPE

The value of tFltrEmbedRefInfEntryCntInsrtd indicates how many entries of the embedded filter (specified by tFilterEmbeddedRefEmbeddedFltrId) are actually placed inside the filter (specified by tFilterEmbeddedRefInsertFltrId). If the object tFilterEmbeddedRefOperState is different from 'in-service' this object will always be zero. Else, the difference between the value of this object and the value of tFltrEmbedRefInfEntryCnt indicates how many entries of the embedded filter were overwritten by local entries in the embedding filter.

OBJECT-TYPE

The table tFilterEmbeddedEntryRefInfoTable contains an entry for each embedded filter entry inserted in a filter with scope other than 'embedded'.

OBJECT-TYPE

An entry in the tFilterEmbeddedEntryRefInfoTable. Rows in the tFilterEmbeddedEntryRefInfoTable are created by the SYSTEM when an embedded filter is inserted into a filter with scope other than 'embedded'. They are destroyed by the SYSTEM when an embedded filter is removed from a filter with scope other than 'embedded'.

OBJECT-TYPE

The object tFltrEmbedEntryFilterType specifies a filter type for the filters specified by tFltrEmbedEntryInsertFltrId and tFltrEmbedEntryEmbeddedFltrId.

OBJECT-TYPE

The value of tFltrEmbedEntryInsertFltrId specifies the filter where the filter specified by tFltrEmbedEntryEmbeddedFltrId is inserted.

OBJECT-TYPE

The value of tFltrEmbedEntryEmbeddedFltrId specifies the ID of the filter inserted in the filter specified by tFltrEmbedEntryInsertFltrId.

OBJECT-TYPE

The value of tFltrEmbedEntryEmbeddedEntryId specifies the ID of the entry inside of the filter specified by tFltrEmbedEntryEmbeddedFltrId.

OBJECT-TYPE

The value of tFltrEmbedEntryInsrtEntryId indicates which entry in the filter specified by tFltrEmbedEntryInsertFltrId corresponds to the entry specified by tFltrEmbedEntryEmbeddedEntryId in the filter specified by tFltrEmbedEntryEmbeddedFltrId.

OBJECT-TYPE

The value of tFltrEmbedEntryRefOperState indicates the current status of the entry identified by tFltrEmbedEntryEmbeddedEntryId of the filter identified by tFltrEmbedEntryEmbeddedFltrId that is embedded into the filter identified by tFltrEmbedEntryInsertFltrId.

OBJECT-TYPE

The value of tIPv6FilterParamsExtTbleLstChgd indicates the sysUpTime at the time of the last modification of tIPv6FilterParamsExtTable. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The table tIPv6FilterParamsExtTable contains, together with the table tIPv6FilterParamsTable info about every IPv6 filter entry in any of the configured IPv6 filters in the system. The table tIPv6FilterParamsExtTable was introduced due to the big size of the tIPv6FilterParamsTable.

OBJECT-TYPE

Information about a particular IPv6 Filter entry. Every IPv6 Filter can have zero or more IPv6 Filter match entries. A filter entry with no match criteria set will match every packet, and the entry action will be taken. Rows are created/deleted by user. Additional match criteria can be found in tIPv6FilterParamsTable.

OBJECT-TYPE

The value of tIPv6FilterParamsExtLastChanged indicates the timestamp of last change to this row in tIPv6FilterParamsExtTable.

OBJECT-TYPE

If Enabled, matches the Authentication Extension Header (51) as per value of the object.

OBJECT-TYPE

If Enabled, matches the Encapsulation Security Payload Extension Header (50) as per value of the object.

OBJECT-TYPE

This object specifies the NAT type to be used when the value of the corresponding tIPv6FilterParamsNatPolicyName object is nat. The value of tIPv6FilterParamsExtNatType is relevant only if the value of tIPv6FilterParamsAction is nat. Setting the value of tIPv6FilterParamsExtNatType to a non-default value is ignored by the system if the value of tIPv6FilterParamsAction is not nat. Furthermore, the value of tIPv6FilterParamsExtNatType is silently reset to the default value by the system if tIPv6FilterParamsAction is set to any value other than nat.

OBJECT-TYPE

The value of the object tIPv6FilterParamsExtPktLenVal1 specifies the packet length value1 to be compared to the value of the Payload Length field of an IPv6 packet header that has hit this filter's entry. The way how the value of this object is used depends on the value of the object tIPv6FilterParamsExtPktLenOper. The value of this object is evaluated only if the value of the object tIPv6FilterParamsExtPktLenOper is other than 'none (0)'. If the value of tIPv6FilterParamsExtPktLenOper is 'range (2)' then the value of this object must be less than the value of tIPv6FilterParamsExtPktLenVal2. If the value of tIPv6FilterParamsExtPktLenOper is 'lt (3)' then the value of this object can be set in range 1..65535. If the value of tIPv6FilterParamsExtPktLenOper is 'gt (4)' then the value of this object can be set in range 0..65534. If both the values of the objects tIPv6FilterParamsExtPktLenOper and tIPv6FilterParamsExtPktLenVal1 need to be changed then it must be done in the same SET SNMP request. Note that the value of this object is silently cleared by the system if tIPv6FilterParamsAction is set to a value other than 'drop (1)' or if tIPv6FilterParamsExtPktLenOper is set to 'none (0)' or if tIPv6FilterParamsExtHopLimitOper is set to a value other than 'none (0)'.

OBJECT-TYPE

The value of the object tIPv6FilterParamsExtPktLenVal2 specifies the packet length value2 to be compared to the value of the Payload Length field of an IPv6 packet header that has hit this filter's entry. The way how the value of this object is used depends on the value of the object tIPv6FilterParamsExtPktLenOper. The value of this object is evaluated only if the value of the object tIPv6FilterParamsExtPktLenOper is 'range (2)'. The value of this object must be greater than the value of tIPv6FilterParamsExtPktLenVal1. If both the values of the objects tIPv6FilterParamsExtPktLenOper and tIPv6FilterParamsExtPktLenVal2 need to be changed then it must be done in the same SET SNMP request. Note that the value of this object is silently cleared by the system if tIPv6FilterParamsAction is set to a value other than 'drop (1)' or if tIPv6FilterParamsExtPktLenOper is set to a value other than 'range (2)' or if tIPv6FilterParamsExtHopLimitOper is set to a value other than 'none (0)'.

OBJECT-TYPE

The value of the object tIPv6FilterParamsExtPktLenOper specifies the way how the values of the objects tIPv6FilterParamsExtPktLenVal1 and tIPv6FilterParamsExtPktLenVal2 are used to form a condition that must be fulfilled in order to execute the action specified by the value of tIPv6FilterParamsAction. Otherwise the opposite action is executed. The value of this object can be set to a non-default value only if the value of the object tIPv6FilterParamsAction is 'drop (1)'. If the value of this object is being changed from the default value to any non-default value the values of the objects tIPv6FilterParamsExtPktLenVal1 and tIPv6FilterParamsExtPktLenVal2 (if applicable) must be sent in the same SET SNMP request. If the value of this object is 'none (0)' than the values of the objects tIPv6FilterParamsExtPktLenVal1 and tIPv6FilterParamsExtPktLenVal2 are ignored and TRUE case action is always executed (see table below). If the value of this object is 'eq (1)' then the value of the Payload Length field of the IPv6 header of the packet that has matched this filter's entry must be equal to the value of the object tIPv6FilterParamsExtPktLenVal1 in order to execute the TRUE case action (see table below). Otherwise the FALSE case action is executed. The value of the object tIPv6FilterParamsExtPktLenVal2 is ignored. If the value of this object is 'range (2)' then the value of the Payload Length field of the IPv6 header of the packet that has matched this filter's entry must be greater than or equal to the value of the object tIPv6FilterParamsExtPktLenVal1 and less than or equal to the value of the object tIPv6FilterParamsExtPktLenVal2 in order to execute the TRUE case action (see table below). Otherwise the FALSE case action is executed. If the value of this object is 'lt (3)' then the value of the Payload Length field of the IPv6 header of the packet that has matched this filter's entry must be less than the value of the object tIPv6FilterParamsExtPktLenVal1 in order to execute the TRUE case action (see table below). Otherwise the FALSE case action is executed. The value of the object tIPv6FilterParamsExtPktLenVal2 is ignored. If the value of this object is 'gt (4)' then the value of the Payload Length field of the IPv6 header of the packet that has matched this filter's entry must be greater than the value of the object tIPv6FilterParamsExtPktLenVal1 in order to execute the TRUE case action (see table below). Otherwise the FALSE case action is executed. The value of the object tIPv6FilterParamsExtPktLenVal2 is ignored. tIPFilterParamsAction | TRUE case action | FALSE case action ------------------------------------------------------------------ drop | drop | forward Allowed ranges for the values of tIPv6FilterParamsExtPktLenVal1 and tIPv6FilterParamsExtPktLenVal2 are: Operator |Packet Length Value 1|Packet Length Value 2 -------------------------------------------------------------------- none (0) | N/A | N/A eq(1) | 0..65535 | N/A range(2) | 0..65534 | (Value1 + 1)..65535 lt(3) | 1..65535 | N/A gt(4) | 0..65534 | N/A The values of the objects tIPv6FilterParamsExtPktLenVal1 and tIPv6FilterParamsExtPktLenVal2 are silently cleared if the value of this object is set to default. Note that the value of this object is silently cleared by the system if tIPv6FilterParamsAction is set to a value other than 'drop (1)' or if tIPv6FilterParamsExtHopLimitOper is set to a value other than 'none (0)'.

OBJECT-TYPE

The value of the object tIPv6FilterParamsExtHopLimitVal1 specifies the Hop Limit value1 to be compared to the value of the Hop Limit field of an IPv6 packet header that has hit this filter's entry. The way how the value of this object is used depends on the value of the object tIPv6FilterParamsExtHopLimitOper. The value of this object can be set to a non-default value only if the value of the object tIPv6FilterParamsExtHopLimitOper is other than 'none (0)'. If the value of tIPv6FilterParamsExtHopLimitOper is 'range (2)' then the value of this object must be less than the value of tIPv6FilterParamsExtHopLimitVal2. If the value of tIPv6FilterParamsExtHopLimitOper is 'lt (3)' then the value of this object can be set in range 1..255. If the value of tIPv6FilterParamsExtHopLimitOper is 'gt (4)' then the value of this object can be set in range 0..254. If both the values of the objects tIPv6FilterParamsExtHopLimitOper and tIPv6FilterParamsExtHopLimitVal1 need to be changed then it must be done in the same SET SNMP request. Note that the value of this object is silently cleared by the system if tIPv6FilterParamsAction is set to a value other than 'drop (1)' or if tIPv6FilterParamsExtHopLimitOper is set to 'none (0)' or if tIPv6FilterParamsExtPktLenOper is set to a value other than 'none (0)'.

OBJECT-TYPE

The value of the object tIPv6FilterParamsExtHopLimitVal2 specifies the Hop Limit value2 to be compared to the value of the Hop Limit field of an IPv6 packet header that has hit this filter's entry. The way how the value of this object is used depends on the value of the object tIPv6FilterParamsExtHopLimitOper. The value of this object can be set to a non-default value only if the value of the object tIPv6FilterParamsExtHopLimitOper is 'range (2)'. The value of this object must be greater than the value of tIPv6FilterParamsExtHopLimitVal1. If both the values of the objects tIPv6FilterParamsExtHopLimitOper and tIPv6FilterParamsExtHopLimitVal2 need to be changed then it must be done in the same SET SNMP request. Note that the value of this object is silently cleared by the system if tIPv6FilterParamsAction is set to a value other than 'drop (1)' or if tIPv6FilterParamsExtHopLimitOper is set to a value other than 'range (2)' or if tIPv6FilterParamsExtPktLenOper is set to a value other than 'none (0)'.

OBJECT-TYPE

The value of the object tIPv6FilterParamsExtHopLimitOper specifies the way how the values of the objects tIPv6FilterParamsExtHopLimitVal1 and tIPv6FilterParamsExtHopLimitVal2 are used to form a condition that must be fulfilled in order to execute the action specified by the value of tIPv6FilterParamsAction. Otherwise the opposite action is executed. The value of this object can be set to a non-default value only if the value of the object tIPv6FilterParamsAction is 'drop (1)'. If the value of this object is being changed from the default value to any non-default value the values of the objects tIPv6FilterParamsExtHopLimitVal1 and tIPv6FilterParamsExtHopLimitVal2 (if applicable) must be sent in the same SET SNMP request. If the value of this object is 'none (0)' than the values of the objects tIPv6FilterParamsExtHopLimitVal1 and tIPv6FilterParamsExtHopLimitVal2 are ignored and TRUE case action is always executed (see table below). If the value of this object is 'eq (1)' then the value of the Hop Limit field of the IPv6 header of the packet that has matched this filter's entry must be equal to the value of the object tIPv6FilterParamsExtHopLimitVal1 in order to execute the TRUE case action (see table below). Otherwise the FALSE case action is executed. The value of the object tIPv6FilterParamsExtHopLimitVal2 is ignored. If the value of this object is 'range (2)' then the value of the Hop Limit field of the IPv6 header of the packet that has matched this filter's entry must be greater than or equal to the value of the object tIPv6FilterParamsExtHopLimitVal1 and less than or equal to the value of the object tIPv6FilterParamsExtHopLimitVal2 in order to execute the TRUE case action (see table below). Otherwise the FALSE case action is executed. If the value of this object is 'lt (3)' then the value of the Hop Limit field of the IPv6 header of the packet that has matched this filter's entry must be less than the value of the object tIPv6FilterParamsExtHopLimitVal1 in order to execute the TRUE case action (see table below). Otherwise the FALSE case action is executed. The value of the object tIPv6FilterParamsExtHopLimitVal2 is ignored. If the value of this object is 'gt (4)' then the value of the Hop Limit field of the IPv6 header of the packet that has matched this filter's entry must be greater than the value of the object tIPv6FilterParamsExtHopLimitVal1 in order to execute the TRUE case action (see table below). Otherwise the FALSE case action is executed. The value of the object tIPv6FilterParamsExtHopLimitVal2 is ignored. tIPv6FilterParamsAction | TRUE case action | FALSE case action ------------------------------------------------------------------ drop | drop | forward Allowed ranges for the values of tIPv6FilterParamsExtHopLimitVal1 and tIPv6FilterParamsExtHopLimitVal2 are: Operator | Hop Limit Value 1 | Hop Limit Value 2 -------------------------------------------------------------------- none (0) | N/A | N/A eq(1) | 0..255 | N/A range(2) | 0..254 | (Value1 + 1)..255 lt(3) | 1..255 | N/A gt(4) | 0..254 | N/A The values of the objects tIPv6FilterParamsExtHopLimitVal1 and tIPv6FilterParamsExtHopLimitVal2 are silently cleared if the value of this object is set to default. Note that the value of this object is silently cleared by the system if tIPv6FilterParamsAction is set to a value other than 'drop (1)' or if tIPv6FilterParamsExtPktLenOper is set to a value other than 'none (0)'.

OBJECT-TYPE

The value of the object tIPv6FilterParamsExtEgressPBR specifies if PBR specified by tIPv6FilterParamsExtEntry will have effect when the filter is applied on egress. tIPv6FilterParamsExtEgressPBR is applicable with these configured actions and action state: - no action - action forward redirect-policy <policy-name> - action forward esi <esi> sf-ip <ipv6-address> vas-interface <interface-name> router <router-instance> - action forward esi <esi> sf-ip <ipv6-address> vas-interface <interface-name> router service-name <service-name> - action forward next-hop <ipv6-address> - action forward next-hop <ipv6-address> router <router-instance> - action forward next-hop <ipv6-address> router service-name <service-name> - action forward next-hop indirect <ipv6-address> - action forward next-hop indirect <ipv6-address> router <router-instance> - action forward next-hop indirect <ipv6-address> router service-name <service-name>

OBJECT-TYPE

The value of the object tIPv6FilterParamsExtEsi specifies the ethernet segment identifier (ESI). ESI is mapped by BGP EVPN to an L2 or L3 capable appliance based on the value of tIPv6FilterParamsAction. Packets matching this entry are steered toward the L2 or L3 appliance. The value '0' indicates that there is no ESI specified. There are two options how to set the value of tIPv6FilterParamsExtEsi: 1. Non zero value of tIPv6FilterParamsExtEsi is set together with non zero values of tIPv6FilterParamsExtFwdEsiVRtrId, tIPv6FilterParamsExtFwdEsiVasIf and tIPv6FilterParamsExtFwdEsiSFIp. In this case value of tIPv6FilterParamsAction is set to 'forwardEsiL3' by the system. 2. Non zero value of tIPv6FilterParamsExtEsi is set together with a non zero value of tIPv6FilterParamsExtFwdEsiSvcId. In this case value of tIPv6FilterParamsAction is set to 'forwardEsiL2' by the system. Note: The value of tIPv6FilterParamsExtEsi is set to '0' by the system if the value of tIPv6FilterParamsAction is set to any value other than 'forwardEsiL2' or 'forwardEsiL3'.

OBJECT-TYPE

The value of the object tIPv6FilterParamsExtFwdEsiSvcId specifies the identifier of VPLS used for VPN/DC connectivity. The value '0' indicates that there is no VPLS identifier specified. The non zero value of tIPv6FilterParamsExtFwdEsiSvcId must be set together with a non zero value of tIPv6FilterParamsExtEsi. Note: The value of tIPv6FilterParamsExtFwdEsiSvcId is set to '0' by the system if the value of the object tIPv6FilterParamsAction is set to any value other than 'forwardEsiL2'.

OBJECT-TYPE

The value of the object tIPv6FilterParamsExtFwdEsiVRtrId specifies the VPRN/rVPLS virtual router identifier used for VPN/DC connectivity. The value '0' indicates that there is no VPRN/rVPLS virtual router identifier specified. The non zero value of tIPv6FilterParamsExtFwdEsiVRtrId must be set together with non zero values of tIPv6FilterParamsExtEsi, tIPv6FilterParamsExtFwdEsiVasIf and tIPv6FilterParamsExtFwdEsiSFIp. Note: The value of tIPv6FilterParamsExtFwdEsiVRtrId is set to '0' by the system if the value of tIPv6FilterParamsAction is set to any value other than 'forwardEsiL3'.

OBJECT-TYPE

The value of the object tIPv6FilterParamsExtFwdEsiSFIp specifies the IPv6 address of the service function toward which traffic is steered. The value '0' indicates that no service function IP address is specified. The non zero value of tIPv6FilterParamsExtFwdEsiSFIp must be set together with non zero values of tIPv6FilterParamsExtFwdEsiVRtrId, tIPv6FilterParamsExtFwdEsiVasIf and tIPv6FilterParamsExtEsi. Note: The value of tIPv6FilterParamsExtFwdEsiSFIp is set to '0' by the system if the value of tIPv6FilterParamsAction is set to any value other than 'forwardEsiL3'.

OBJECT-TYPE

The value of the object tIPv6FilterParamsExtPbrDwnActOvr specifies the filter action which will be performed when the PBR/PBF target for this entry is not available. If the value of tIPvXFltrEntryActAction is not one of the following values then tIPv6FilterParamsExtPbrDwnActOvr must be set to the value 'none': - forwardEsiL2 - forwardEsiL3 - forwardSap - forwardSdp - forwardNextHopRtr If the value of tIPFilterParamsExtPbrDwnActOvr is different from 'none' then PBR/PBF destination availability checking for an entry is turned on. There is a limit to the number of filter entries with the destination availability checking turned on. Entries with the value of tIPvXFltrEntryActAction equal to 'forwardEsiL2' or 'forwardEsiL3' are not counted against this limit. Refer to the description of the textual convention TFilterPbrDownActionOvr for more details.

OBJECT-TYPE

The value of the object tIPv6FilterParamsExtFwdEsiVasIf specifies the virtual router interface index of VPRN RVPLS interface used for VPN/DC connectivity. The value '0' indicates that no interface id is specified. The non zero value of tIPv6FilterParamsExtFwdEsiVasIf must be set together with non zero values of tIPv6FilterParamsExtFwdEsiVRtrId, tIPv6FilterParamsExtFwdEsiSFIp and tIPv6FilterParamsExtEsi. Note: The value of tIPv6FilterParamsExtFwdEsiVasIf is set to '0' by the system if the value of tIPv6FilterParamsAction is set to any value other than 'forwardEsiL3'.

OBJECT-TYPE

The value of the object tIPv6FilterParamsExtStickyDst specifies how long will system wait (in seconds) until it activates the best action (action with available PBR/PBF destination and the highest priority). Until then the action specified by tIPv6FilterParamsExtPbrDwnActOvr will be taken on a packet matching the filter entry. After the value of the active destination is fixed it will remain unchanged until the active PBR/PBF destination becomes unreachable. The value of -1 indicates that the property of PBR destination stickiness is turned off. When the property of stickiness is turned off the active PBR/PBF destination is always the one which is available and has the highest priority. The countdown starts when there was no PBR/PBF destination reachable and any PBR/PBF destination becomes reachable. tIPv6FilterParamsExtStickyDst can be set to value other than -1 only if the value of tIPvXFltrEntryActAction is one of the following values: - forwardSap - forwardSdp - forwardNextHopRtr

OBJECT-TYPE

The value of the object tIPv6FilterParamsExtHoldRemain indicates the remaining time in seconds, until the best action will become active and will be fixed. Best action is: - primary action if PBR target status of primary action is up. - secondary action if PBR target status of secondary action is up and PBR target status of primary action is down. - none if both PBR targets are down

OBJECT-TYPE

The value of the object tIPv6FilterParamsExtDownloadAct indicates the filter entry action downloaded to IOM. Refer to the description of the textual convention TFilterDownloadedAction for more information.

OBJECT-TYPE

If Enabled, matches a TCP Fin as per value of the object.

OBJECT-TYPE

If Enabled, matches a TCP Rst as per value of the object.

OBJECT-TYPE

If Enabled, matches a TCP Psh as per value of the object.

OBJECT-TYPE

If Enabled, matches a TCP Urg as per value of the object.

OBJECT-TYPE

If Enabled, matches a TCP Ece as per value of the object.

OBJECT-TYPE

If Enabled, matches a TCP Cwr as per value of the object.

OBJECT-TYPE

If Enabled, matches a TCP Ns as per value of the object.

OBJECT-TYPE

Source MAC to match for this policy filter entry.

OBJECT-TYPE

Source MAC mask value for this policy MAC filter entry. The mask is ANDed with the MAC to match tIPv6FilterParamsExtSrcMac. A cleared bit means ignore this bit, do not match. A set bit means match this bit with tIPv6FilterParamsExtSrcMac. Use the value 00-00-00-00-00-00 to disable this filter criteria.

OBJECT-TYPE

The value of the object tIPv6FilterParamsExtMxPktLenVal1 specifies the value1 to be compared to total length of the packet including header. The way how the value of this object is used depends on the value of the object tIPv6FilterParamsExtMxPktLenOper. The value of this object can be set to a non-default value only if the value of the object tIPv6FilterParamsExtMxPktLenOper is other than 'none (0)'. If the value of tIPv6FilterParamsExtMxPktLenOper is 'range (2)' then the value of this object must be less than the value of tIPv6FilterParamsExtMxPktLenVal2. If the value of tIPv6FilterParamsExtMxPktLenOper is 'lt (3)' then the value of this object can be set in range 41..65535. If the value of tIPv6FilterParamsExtMxPktLenOper is 'gt (4)' then the value of this object can be set in range 40..65574. If both the values of the objects tIPv6FilterParamsExtMxPktLenOper and tIPv6FilterParamsExtMxPktLenVal1 need to be changed then it must be done in the same SET SNMP request.

OBJECT-TYPE

The value of the object tIPv6FilterParamsExtMxPktLenVal2 specifies the value2 to be compared to total length of the packet including header. The way how the value of this object is used depends on the value of the object tIPv6FilterParamsExtMxPktLenOper. The value of this object can be set to a non-default value only if the value of the object tIPv6FilterParamsExtMxPktLenOper is 'range (2)'. The value of this object must be greater than the value of tIPv6FilterParamsExtMxPktLenVal1. If both the values of the objects tIPv6FilterParamsExtMxPktLenOper and tIPv6FilterParamsExtMxPktLenVal2 need to be changed then it must be done in the same SET SNMP request.

OBJECT-TYPE

The value of the object tIPv6FilterParamsExtMxPktLenOper specifies the way how the values of the objects tIPv6FilterParamsExtMxPktLenVal1 and tIPv6FilterParamsExtMxPktLenVal2 are used. If the value of this object is 'eq (1)' then the value of the Total Length field of the IP header of the packet that has matched this filter's entry must be equal to the value of the object tIPv6FilterParamsExtMxPktLenVal1 (see table below). The value of the object tIPv6FilterParamsExtMxPktLenVal2 is ignored. If the value of this object is 'range (2)' then the value of the Total Length field of the IP header of the packet that has matched this filter's entry must be greater than or equal to the value of the object tIPv6FilterParamsExtMxPktLenVal1 and less than or equal to the value of the object tIPv6FilterParamsExtMxPktLenVal2. If the value of this object is 'lt (3)' then the value of the Total Length field of the IP header of the packet that has matched this filter's entry must be less than the value of the object tIPv6FilterParamsExtMxPktLenVal1 (see table below). The value of the object tIPv6FilterParamsExtMxPktLenVal2 is ignored. If the value of this object is 'gt (4)' then the value of the Total Length field of the IP header of the packet that has matched this filter's entry must be greater than the value of the object tIPv6FilterParamsExtMxPktLenVal1 (see table below). The value of the object tIPv6FilterParamsExtMxPktLenVal2 is ignored. Allowed ranges for the values of tIPv6FilterParamsExtMxPktLenVal1 and tIPv6FilterParamsExtMxPktLenVal2 are: Operator |Packet Length Value 1|Packet Length Value 2 -------------------------------------------------------------------- none (0) | N/A | N/A eq(1) | 0..65535 | N/A range(2) | 0..65534 | (Value1 + 1)..65535 lt(3) | 1..65535 | N/A gt(4) | 0..65534 | N/A

OBJECT-TYPE

The object tFilterEmbedOpenflowTableLstChg indicates the sysUpTime at the time of the last modification of tFilterEmbedOpenflowTable. If no changes were made to the table since the last re-initialization of the local network management subsystem, this object contains the value zero.

OBJECT-TYPE

The table tFilterEmbedOpenflowTable contains an entry for each open-flow flowtable embedded in a filter with scope other than 'embedded'.

OBJECT-TYPE

An entry in the tFilterEmbedOpenflowTable.

OBJECT-TYPE

The value of tFilterEmbedOpenflowOfsName specifies the name of the open-flow switch which contains the flowtable to be inserted in the filter specified by tFilterEmbedOpenflowInsertFltrId.

OBJECT-TYPE

The object tFilterEmbedOpenflowFilterType specifies the type of filter for the filter specified by tFilterEmbedOpenflowInsertFltrId.

OBJECT-TYPE

The value of tFilterEmbedOpenflowInsertFltrId specifies the filter where the open-flow switch specified by tFilterEmbedOpenflowOfsName is to be embedded. Values outside of range 1..65535 are reserved for entries dynamically created by the system and cannot be used in any SNMP SET operation.

OBJECT-TYPE

The value of tFilterEmbedOpenflowOffset specifies the offset of inserted entries.

OBJECT-TYPE

The value of the object tFilterEmbedOpenflowRowStatus specifies the status of a row in tFilterEmbedOpenflowTable. Rows are created and destroyed by SNMP SET operations on this object. Only values 'active (1)', 'createAndGo(4)', and 'destroy (6)' are supported.

OBJECT-TYPE

The value of tFilterEmbedOpenflowAdminState specifies the administrative state of the embed request defined by this row. If an active embedding cannot be fulfilled due to dynamic events, this object will be set to 'inactive' automatically by the system. In those cases, the object tFilterEmbedOpenflowOperState will indicate the failure reason.

OBJECT-TYPE

The value of tFilterEmbedOpenflowOperState indicates the operational state of the embed request defined by this row.

OBJECT-TYPE

The value of tFilterEmbedOflowSvcContext specifies the service context of this open-flow embedding. When no service context is present, this object is equal to default value.

OBJECT-TYPE

The value of tFilterEmbedOflowSapContextPort specifies the port-id of the sap context of this open-flow embedding. When no sap context is present, this object is set to default value.

OBJECT-TYPE

The value of tFilterEmbedOflowSapContextEncap specifies the encap value of the sap context of this open-flow embedding. When no sap context is present, this object is set to default value.

OBJECT-TYPE

The value of tFilterEmbedOflowContextType specifies the context in which the open-flow embedding is inserted into filter. When no context is present, this object is set to grt value.

OBJECT-TYPE

The table tFilterEmbedOpenflowInfoTable contains an entry for each open-flow switch embedded in a filter with scope other than 'embedded'. This row complements the corresponding row in the tFilterEmbedOpenflowTable with read-only operational info.

OBJECT-TYPE

An entry in the tFilterEmbedOpenflowInfoTable.

OBJECT-TYPE

The value of tFltrEmbedOfInfoEntryCnt indicates how many entries are eligible for embedding from the open-flow switch specified by tFilterEmbedOpenflowOfsName.

OBJECT-TYPE

The value of tFltrEmbedOfInfoEntryCntInsrtd indicates how many entries are actually placed inside the filter by the open-flow switch specified by tFilterEmbedOpenflowOfsName. If the object tFilterEmbedOpenflowOperState is different from 'in-service' this object will always be zero. Else, the difference between the value of this object and the value of tFltrEmbedOfInfoEntryCnt indicates how many entries were overwritten by local entries in the embedding filter.

OBJECT-TYPE

The table tFilterOpenflowEntryInfoTable contains an entry for each open-flow filter entry inserted in a filter with scope other than 'embedded'.

OBJECT-TYPE

An entry in the tFilterOpenflowEntryInfoTable. Rows in the tFilterOpenflowEntryInfoTable are created by the SYSTEM when an open-flow switch is embedded into a filter. They are destroyed by the SYSTEM when an open-flow switch embedding is removed from a filter.

OBJECT-TYPE

The value of tFltrEmbedOfEntryOfsName specifies the name of the open-flow switch which contains the flowtable to be inserted in the filter specified by tFltrEmbedOfEntryInsertFltrId.

OBJECT-TYPE

The object tFltrEmbedOfEntryFilterType specifies the type of filter for the filter specified by tFltrEmbedOfEntryInsertFltrId.

OBJECT-TYPE

The value of tFltrEmbedOfEntryInsertFltrId specifies the filter where the open-flow switch specified by tFltrEmbedOfEntryOfsName is to be embedded. Values outside of range 1..65535 are reserved for entries dynamically created by the system.

OBJECT-TYPE

The value of tFltrEmbedOfEntryOfEntryId specifies the base ID of the entry as determined by the priority of the corresponding flow-rule in the open-flow switch specified by tFltrEmbedOfEntryOfsName.

OBJECT-TYPE

The value of tFltrEmbedOfEntryInsrtEntryId indicates the position of the filter entry in the filter specified by tFltrEmbedOfEntryInsertFltrId.

OBJECT-TYPE

The value of tFltrEmbedOfEntryInsrtEntryState indicates the current status of the embedding of the entry identified by tFltrEmbedOfEntryOfEntryId from the open-flow switch identified by tFltrEmbedOfEntryOfsName that is embedded into the filter identified by tFltrEmbedOfEntryInsertFltrId.

OBJECT-TYPE

The value of tIPFilterParamsExtTbleLstChgd indicates the sysUpTime at the time of the last modification of tIPFilterParamsExtTable. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The table tIPFilterParamsExtTable contains, together with the table tIPFilterParamsTable info about every IP filter entry in any of the configured IP filters in the system. The table tIPFilterParamsExtTable was introduced due to the big size of the tIPFilterParamsTable.

OBJECT-TYPE

Information about a particular IP Filter entry. Every IP Filter can have zero or more IP Filter match entries. A filter entry with no match criteria set will match every packet, and the entry action will be taken. Entries are created/deleted by the system when a corresponding tIPFilterParamsEntry is created/deleted. Additional match criteria can be found in tIPFilterParamsTable.

OBJECT-TYPE

The value of the object tIPFilterParamsExtLastChanged indicates the timestamp of last change of this row in tIPFilterParamsExtTable.

OBJECT-TYPE

The value of the object tIPFilterParamsExtPktLenVal1 specifies the packet length value1 to be compared to the value of the Total Length field of an IP packet header that has hit this filter's entry. The way how the value of this object is used depends on the value of the object tIPFilterParamsExtPktLenOper. The value of this object can be set to a non-default value only if the value of the object tIPFilterParamsExtPktLenOper is other than 'none (0)'. If the value of tIPFilterParamsExtPktLenOper is 'range (2)' then the value of this object must be less than the value of tIPFilterParamsExtPktLenVal2. If the value of tIPFilterParamsExtPktLenOper is 'lt (3)' then the value of this object can be set in range 1..65535. If the value of tIPFilterParamsExtPktLenOper is 'gt (4)' then the value of this object can be set in range 0..65534. If both the values of the objects tIPFilterParamsExtPktLenOper and tIPFilterParamsExtPktLenVal1 need to be changed then it must be done in the same SET SNMP request. Note that the value of this object is silently cleared by the system if tIPFilterParamsAction is set to a value other than 'drop (1)' or if tIPFilterParamsExtPktLenOper is set to 'none (0)' or if tIPFilterParamsExtTTLOper is set to a value other than 'none (0)'.

OBJECT-TYPE

The value of the object tIPFilterParamsExtPktLenVal2 specifies the packet length value2 to be compared to the value of the Total Length field of an IP packet header that has hit this filter's entry. The way how the value of this object is used depends on the value of the object tIPFilterParamsExtPktLenOper. The value of this object can be set to a non-default value only if the value of the object tIPFilterParamsExtPktLenOper is 'range (2)'. The value of this object must be greater than the value of tIPFilterParamsExtPktLenVal1. If both the values of the objects tIPFilterParamsExtPktLenOper and tIPFilterParamsExtPktLenVal2 need to be changed then it must be done in the same SET SNMP request. Note that the value of this object is silently cleared by the system if tIPFilterParamsAction is set to a value other than 'drop (1)' or if tIPFilterParamsExtPktLenOper is set to value other than 'range (2)' or if tIPFilterParamsExtTTLOper is set to a value other than 'none (0)'.

OBJECT-TYPE

The value of the object tIPFilterParamsExtPktLenOper specifies the way how the values of the objects tIPFilterParamsExtPktLenVal1 and tIPFilterParamsExtPktLenVal2 are used to form a condition that must be fulfilled in order to execute the action specified by the value of tIPFilterParamsAction. Otherwise the opposite action is executed. The value of this object can be set to a non-default value only if the value of the object tIPFilterParamsAction is 'drop (1)'. If the value of this object is being changed from the default value to any non-default value the values of the objects tIPFilterParamsExtPktLenVal1 and tIPFilterParamsExtPktLenVal2 (if applicable) must be sent in the same SET SNMP request. If the value of this object is 'none (0)' than the values of the objects tIPFilterParamsExtPktLenVal1 and tIPFilterParamsExtPktLenVal2 are ignored and TRUE case action is always executed (see table below). If the value of this object is 'eq (1)' then the value of the Total Length field of the IP header of the packet that has matched this filter's entry must be equal to the value of the object tIPFilterParamsExtPktLenVal1 in order to execute the TRUE case action (see table below). Otherwise the FALSE case action is executed. The value of the object tIPFilterParamsExtPktLenVal2 is ignored. If the value of this object is 'range (2)' then the value of the Total Length field of the IP header of the packet that has matched this filter's entry must be greater than or equal to the value of the object tIPFilterParamsExtPktLenVal1 and less than or equal to the value of the object tIPFilterParamsExtPktLenVal2 in order to execute the TRUE case action (see table below). Otherwise the FALSE case action is executed. If the value of this object is 'lt (3)' then the value of the Total Length field of the IP header of the packet that has matched this filter's entry must be less than the value of the object tIPFilterParamsExtPktLenVal1 in order to execute the TRUE case action (see table below). Otherwise the FALSE case action is executed. The value of the object tIPFilterParamsExtPktLenVal2 is ignored. If the value of this object is 'gt (4)' then the value of the Total Length field of the IP header of the packet that has matched this filter's entry must be greater than the value of the object tIPFilterParamsExtPktLenVal1 in order to execute the TRUE case action (see table below). Otherwise the FALSE case action is executed. The value of the object tIPFilterParamsExtPktLenVal2 is ignored. tIPFilterParamsAction | TRUE case action | FALSE case action ------------------------------------------------------------------ drop | drop | forward Allowed ranges for the values of tIPFilterParamsExtPktLenVal1 and tIPFilterParamsExtPktLenVal2 are: Operator |Packet Length Value 1|Packet Length Value 2 -------------------------------------------------------------------- none (0) | N/A | N/A eq(1) | 0..65535 | N/A range(2) | 0..65534 | (Value1 + 1)..65535 lt(3) | 1..65535 | N/A gt(4) | 0..65534 | N/A The values of the objects tIPFilterParamsExtPktLenVal1 and tIPFilterParamsExtPktLenVal2 are silently cleared if the value of this object is set to default. Note that the value of this object is silently cleared by the system if tIPFilterParamsAction is set to a value other than 'drop (1)' or if tIPFilterParamsExtTTLOper is set to a value other than 'none (0)'.

OBJECT-TYPE

The value of the object tIPFilterParamsExtTTLVal1 specifies the Time-To-Live value1 to be compared to the value of the Time-To-Live field of an IP packet header that has hit this filter's entry. The way how the value of this object is used depends on the value of the object tIPFilterParamsExtTTLOper. The value of this object can be set to a non-default value only if the value of the object tIPFilterParamsExtTTLOper is other than 'none (0)'. If the value of tIPFilterParamsExtTTLOper is 'range (2)' then the value of this object must be less than the value of tIPFilterParamsExtTTLVal2. If the value of tIPFilterParamsExtTTLOper is 'lt (3)' then the value of this object can be set in range 1..255. If the value of tIPFilterParamsExtTTLOper is 'gt (4)' then the value of this object can be set in range 0..254. If both the values of the objects tIPFilterParamsExtTTLOper and tIPFilterParamsExtTTLVal1 need to be changed then it must be done in the same SET SNMP request. Note that the value of this object is silently cleared by the system if tIPFilterParamsAction is set to a value other than 'drop (1)' or if tIPFilterParamsExtTTLOper is set to 'none (0)' or if tIPFilterParamsExtPktLenOper is set to a value other than 'none (0)'.

OBJECT-TYPE

The value of the object tIPFilterParamsExtTTLVal2 specifies the Time-To-Live value2 to be compared to the value of the Time-To-Live field of an IP packet header that has hit this filter's entry. The way how the value of this object is used depends on the value of the object tIPFilterParamsExtTTLOper. The value of this object can be set to a non-default value only if the value of the object tIPFilterParamsExtTTLOper is 'range (2)'. The value of this object must be greater than the value of tIPFilterParamsExtTTLVal1. If both the values of the objects tIPFilterParamsExtTTLOper and tIPFilterParamsExtTTLVal2 need to be changed then it must be done in the same SET SNMP request. Note that the value of this object is silently cleared by the system if tIPFilterParamsAction is set to a value other than 'drop (1)' or if tIPFilterParamsExtTTLOper is set to a value other than 'range (2)' or if tIPFilterParamsExtPktLenOper is set to a value other than 'none (0)'.

OBJECT-TYPE

The value of the object tIPFilterParamsExtTTLOper specifies the way how the values of the objects tIPFilterParamsExtTTLVal1 and tIPFilterParamsExtTTLVal2 are used to form a condition that must be fulfilled in order to execute the action specified by the value of tIPFilterParamsAction. Otherwise the opposite action is executed. The value of this object can be set to a non-default value only if the value of the object tIPFilterParamsAction is 'drop (1)'. If the value of this object is being changed from the default value to any non-default value the values of the objects tIPFilterParamsExtTTLVal1 and tIPFilterParamsExtTTLVal2 (if applicable) must be sent in the same SET SNMP request. If the value of this object is 'none (0)' than the values of the objects tIPFilterParamsExtTTLVal1 and tIPFilterParamsExtTTLVal2 are ignored and TRUE case action is always executed (see table below). If the value of this object is 'eq (1)' then the value of the Time-To-Live field of the IP header of the packet that has matched this filter's entry must be equal to the value of the object tIPFilterParamsExtTTLVal1 in order to execute the TRUE case action (see table below). Otherwise the FALSE case action is executed. The value of the object tIPFilterParamsExtTTLVal2 is ignored. If the value of this object is 'range (2)' then the value of the Time-To-Live field of the IP header of the packet that has matched this filter's entry must be greater than or equal to the value of the object tIPFilterParamsExtTTLVal1 and less than or equal to the value of the object tIPFilterParamsExtTTLVal2 in order to execute the TRUE case action (see table below). Otherwise the FALSE case action is executed. If the value of this object is 'lt (3)' then the value of the Time-To-Live field of the IP header of the packet that has matched this filter's entry must be less than the value of the object tIPFilterParamsExtTTLVal1 in order to execute the TRUE case action (see table below). Otherwise the FALSE case action is executed. The value of the object tIPFilterParamsExtTTLVal2 is ignored. If the value of this object is 'gt (4)' then the value of the Time-To-Live field of the IP header of the packet that has matched this filter's entry must be greater than the value of the object tIPFilterParamsExtTTLVal1 in order to execute the TRUE case action (see table below). Otherwise the FALSE case action is executed. The value of the object tIPFilterParamsExtTTLVal2 is ignored. tIPFilterParamsAction | TRUE case action | FALSE case action ------------------------------------------------------------------ drop | drop | forward Allowed ranges for the values of tIPFilterParamsExtTTLVal1 and tIPFilterParamsExtTTLVal2 are: Operator | Time-To-Live Value 1| Time-To-Live Value 2 -------------------------------------------------------------------- none (0) | N/A | N/A eq(1) | 0..255 | N/A range(2) | 0..254 | (Value1 + 1)..255 lt(3) | 1..255 | N/A gt(4) | 0..254 | N/A The values of the objects tIPFilterParamsExtTTLVal1 and tIPFilterParamsExtTTLVal2 are silently cleared if the value of this object is set to default. Note that the value of this object is silently cleared by the system if tIPFilterParamsAction is set to a value other than 'drop (1)' or if tIPFilterParamsExtPktLenOper is set to a value other than 'none (0)'.

OBJECT-TYPE

The value of the object tIPFilterParamsExtEgressPBR specifies if PBR specified by tIPFilterParamsExtEntry will have effect when the filter is applied on egress. tIPFilterParamsExtEgressPBR is applicable with these configured actions and action state: - no action - action forward redirect-policy <policy-name> - action forward esi <esi> sf-ip <ip-address> vas-interface <interface-name> router <router-instance> - action forward esi <esi> sf-ip <ip-address> vas-interface <interface-name> router service-name <service-name> - action forward next-hop <ip-address> - action forward next-hop <ip-address> router <router-instance> - action forward next-hop <ip-address> router service-name <service-name> - action forward next-hop indirect <ip-address> - action forward next-hop indirect <ip-address> router <router-instance> - action forward next-hop indirect <ip-address> router service-name <service-name>

OBJECT-TYPE

The value of the object tIPFilterParamsExtEsi specifies the ethernet segment identifier (ESI). ESI is mapped by BGP EVPN to an L2 or L3 capable appliance based on the value of tIPFilterParamsAction. Packets matching this entry are steered toward the L2 or L3 appliance. The value '0' indicates that there is no ESI specified. There are two options how to set the value of tIPFilterParamsExtEsi: 1. Non zero value of tIPFilterParamsExtEsi is set together with non zero values of tIPFilterParamsExtFwdEsiVRtrId, tIPFilterParamsExtFwdEsiVasIf and tIPFilterParamsExtFwdEsiSFIp. In this case value of tIPFilterParamsAction is set to 'forwardEsiL3' by the system. 2. Non zero value of tIPFilterParamsExtEsi is set together with a non zero value of tIPFilterParamsExtFwdEsiSvcId. In this case value of tIPFilterParamsAction is set to 'forwardEsiL2' by the system. Note: The value of tIPFilterParamsExtEsi is set to '0' by the system if the value of tIPFilterParamsAction is set to any value other than 'forwardEsiL2' or 'forwardEsiL3'.

OBJECT-TYPE

The value of the object tIPFilterParamsExtFwdEsiSvcId specifies the identifier of a VPLS used for VPN/DC connectivity. The value '0' indicates that there is no VPLS identifier specified. The non zero value of tIPFilterParamsExtFwdEsiSvcId must be set together with a non zero value of tIPFilterParamsExtEsi. Note: The value of tIPFilterParamsExtFwdEsiSvcId is set to '0' by the system if the value of tIPFilterParamsAction is set to any value other than 'forwardEsiL2'.

OBJECT-TYPE

The value of the object tIPFilterParamsExtFwdEsiVRtrId specifies the VPRN/rVPLS virtual router identifier used for VPN/DC connectivity. The value '0' indicates that there is no VPRN/rVPLS virtual router identifier specified. The non zero value of tIPFilterParamsExtFwdEsiVRtrId must be set together with non zero values of tIPFilterParamsExtEsi, tIPFilterParamsExtFwdEsiVasIf and tIPFilterParamsExtFwdEsiSFIp. Note: The value of tIPFilterParamsExtFwdEsiVRtrId is set to '0' by the system if the value of tIPFilterParamsAction is set to any value other than 'forwardEsiL3'.

OBJECT-TYPE

The value of the object tIPFilterParamsExtFwdEsiSFIp specifies the IP address of the service function toward which traffic is steered. The value '0' indicates that no service function IP address is specified. The non zero value of tIPFilterParamsExtFwdEsiSFIp must be set together with a non zero values of tIPFilterParamsExtFwdEsiVRtrId, tIPFilterParamsExtFwdEsiVasIf and tIPFilterParamsExtEsi. Note: The value of tIPFilterParamsExtFwdEsiSFIp is set to default by the system if the value of tIPFilterParamsAction is set to any value other than 'forwardEsiL3'.

OBJECT-TYPE

The value of the object tIPFilterParamsExtPbrDwnActOvr specifies the filter action which will be performed when the PBR/PBF target for this entry is not available. If the value of tIPvXFltrEntryActAction is not one of the following values then tIPFilterParamsExtPbrDwnActOvr must be set to the value 'none': - forwardEsiL2 - forwardEsiL3 - forwardSap - forwardSdp - forwardNextHopRtr If the value of tIPFilterParamsExtPbrDwnActOvr is different from 'none' then PBR/PBF destination availability checking for an entry is turned on. There is a limit to the number of filter entries with the destination availability checking turned on. Entries with the value of tIPvXFltrEntryActAction equal to 'forwardEsiL2' or 'forwardEsiL3' are not counted against this limit. Refer to the description of the textual convention TFilterPbrDownActionOvr for more details.

OBJECT-TYPE

The value of the object tIPFilterParamsExtFwdEsiVasIf specifies the virtual router interface index of VPRN RVPLS interface used for VPN/DC connectivity. The value '0' indicates that no interface id is specified. The non zero value of tIPFilterParamsExtFwdEsiVasIf must be set together with a non zero values of tIPFilterParamsExtFwdEsiVRtrId, tIPFilterParamsExtFwdEsiSFIp and tIPFilterParamsExtEsi. Note: The value of tIPFilterParamsExtFwdEsiVasIf is set to '0' by the system if the value of tIPFilterParamsAction is set to any value other than 'forwardEsiL3'.

OBJECT-TYPE

The value of the object tIPFilterParamsExtStickyDst specifies how long the system will wait (in seconds) until it activates the best action (action with available PBR/PBF destination and the highest priority). Until then the action specified by tIPFilterParamsExtPbrDwnActOvr will be taken on a packet matching the filter entry. After the value of the active destination is fixed it will remain unchanged until the active PBR/PBF destination becomes unreachable. The value of -1 indicates that the property of PBR destination stickiness is turned off. When the property of stickiness is turned off the active PBR/PBF destination is always the one which is available and has the highest priority. The countdown starts when there was no PBR/PBF destination reachable and any PBR/PBF destination becomes reachable. tIPFilterParamsExtStickyDst can be set to value other than -1 only if the value of tIPvXFltrEntryActAction is one of following values: - forwardSap - forwardSdp - forwardNextHopRtr

OBJECT-TYPE

The value of the object tIPFilterParamsExtHoldRemain indicates the remaining time in seconds, until the best action will become active and will be fixed. Best action is: - primary action if PBR target status of primary action is up. - secondary action if PBR target status of secondary action is up and PBR target status of primary action is down. - none if both PBR targets are down

OBJECT-TYPE

The value of the object tIPFilterParamsExtDownloadAct indicates the filter entry action downloaded to IOM. Refer to the description of the textual convention TFilterDownloadedAction for more information.

OBJECT-TYPE

If Enabled, matches a TCP Fin as per value of the object.

OBJECT-TYPE

If Enabled, matches a TCP Rst as per value of the object.

OBJECT-TYPE

If Enabled, matches a TCP Psh as per value of the object.

OBJECT-TYPE

If Enabled, matches a TCP Urg as per value of the object.

OBJECT-TYPE

If Enabled, matches a TCP Ece as per value of the object.

OBJECT-TYPE

If Enabled, matches a TCP Cwr as per value of the object.

OBJECT-TYPE

If Enabled, matches a TCP Ns as per value of the object.

OBJECT-TYPE

Source MAC to match for this policy filter entry.

OBJECT-TYPE

Source MAC mask value for this policy MAC filter entry. The mask is ANDed with the MAC to match tIPFilterParamsExtSrcMac. A cleared bit means ignore this bit, do not match. A set bit means match this bit with tIPFilterParamsExtSrcMac. Use the value 00-00-00-00-00-00 to disable this filter criteria.

OBJECT-TYPE

The value of the object tIPFilterParamsExtMxPktLenVal1 specifies the value1 to be compared to the value of 'Total Length' field of IPv4 header of the packet that has hit this filter's entry. The way how the value of this object is used depends on the value of the object tIPFilterParamsExtMxPktLenOper. The value of this object can be set to a non-default value only if the value of the object tIPFilterParamsExtMxPktLenOper is other than 'none (0)'. If the value of tIPFilterParamsExtMxPktLenOper is 'range (2)' then the value of this object must be less than the value of tIPFilterParamsExtMxPktLenVal2. If the value of tIPFilterParamsExtMxPktLenOper is 'lt (3)' then the value of this object can be set in range 1..65535. If the value of tIPFilterParamsExtMxPktLenOper is 'gt (4)' then the value of this object can be set in range 0..65534. If both the values of the objects tIPFilterParamsExtMxPktLenOper and tIPFilterParamsExtMxPktLenVal1 need to be changed then it must be done in the same SET SNMP request.

OBJECT-TYPE

The value of the object tIPFilterParamsExtMxPktLenVal2 specifies the value2 to be compared to the value of 'Total Length' field of IPv4 header of the packet that has hit this filter's entry. The way how the value of this object is used depends on the value of the object tIPFilterParamsExtMxPktLenOper. The value of this object can be set to a non-default value only if the value of the object tIPFilterParamsExtMxPktLenOper is 'range (2)'. The value of this object must be greater than the value of tIPFilterParamsExtMxPktLenVal1. If both the values of the objects tIPFilterParamsExtMxPktLenOper and tIPFilterParamsExtMxPktLenVal2 need to be changed then it must be done in the same SET SNMP request.

OBJECT-TYPE

The value of the object tIPFilterParamsExtMxPktLenOper specifies the way how the values of the objects tIPFilterParamsExtMxPktLenVal1 and tIPFilterParamsExtMxPktLenVal2 are used. If the value of this object is 'eq (1)' then the value of the Total Length field of the IP header of the packet that has matched this filter's entry must be equal to the value of the object tIPFilterParamsExtMxPktLenVal1 (see table below). The value of the object tIPFilterParamsExtMxPktLenVal2 is ignored. If the value of this object is 'range (2)' then the value of the Total Length field of the IP header of the packet that has matched this filter's entry must be greater than or equal to the value of the object tIPFilterParamsExtMxPktLenVal1 and less than or equal to the value of the object tIPFilterParamsExtMxPktLenVal2. If the value of this object is 'lt (3)' then the value of the Total Length field of the IP header of the packet that has matched this filter's entry must be less than the value of the object tIPFilterParamsExtMxPktLenVal1 (see table below). The value of the object tIPFilterParamsExtMxPktLenVal2 is ignored. If the value of this object is 'gt (4)' then the value of the Total Length field of the IP header of the packet that has matched this filter's entry must be greater than the value of the object tIPFilterParamsExtMxPktLenVal1 (see table below). The value of the object tIPFilterParamsExtMxPktLenVal2 is ignored. Allowed ranges for the values of tIPFilterParamsExtMxPktLenVal1 and tIPFilterParamsExtMxPktLenVal2 are: Operator |Packet Length Value 1|Packet Length Value 2 -------------------------------------------------------------------- none (0) | N/A | N/A eq(1) | 0..65535 | N/A range(2) | 0..65534 | (Value1 + 1)..65535 lt(3) | 1..65535 | N/A gt(4) | 0..65534 | N/A

OBJECT-TYPE

The value of the object tFilterRPlcyDstTableLastChg indicates the sysUpTime at the time of the last modification of tFilterRPlcyDstTable. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The table tFilterRPlcyDstTable contains information pertaining to Redirect Policy destinations configured on this system.

OBJECT-TYPE

Entry contains information about a particular Redirect Policy destination. Rows in the table tFilterRPlcyDstTable are created and destroyed by SNMP SET operations on the object tFltrRPDstRowStatus.

OBJECT-TYPE

The value of the object tFltrRPDstAddrType specifies the context in which the value of the object tFltrRPDstAddr is interpreted. Only the following values are supported: ipv4(1) ipv6(2) The value of this object must be the same for all destinations in a Redirect Policy.

OBJECT-TYPE

The value of the object tFltrRPDstAddr specifies the IP address of the destination. The value must be consistent with the IP version value of the associated tFltrRPDstAddrType object.

OBJECT-TYPE

The value of the object tFltrRPDstLastChanged indicates the timestamp of last change of this row in tFilterRPlcyDstTable.

OBJECT-TYPE

The value of the object tFltrRPDstRowStatus specifies the status of the conceptual row in tFilterRPlcyDstTable. Rows can be created and destroyed by SNMP SET operations on this object.

OBJECT-TYPE

The value of the object tFltrRPDstAdminState specifies the configured administrative state of the destination. If the administrative state is 'outOfService' then all tests for this destination will not be conducted.

OBJECT-TYPE

The value of the object tFltrRPDstOperState indicates the operational state of the destination.

OBJECT-TYPE

The value of the object tFltrRPDstDescription specifies the user-provided description for this destination.

OBJECT-TYPE

The value of the object tFltrRPDstAdminPriority specifies the configured priority for this destination. The value is used as a base value for the calculation of the operational priority indicated by the value of the object tFltrRPDstOperPriority.

OBJECT-TYPE

The value of the object tFltrRPDstOperPriority indicates the current dynamic priority of this destination. It is derived from the base priority indicated by the value of the object tFltrRPDstAdminPriority and results of tests assigned to the destination. A destination with the highest operational priority across multiple destinations in a Redirect Policy is used as the preferred destination. If the value of the object tFltrRPDstOperState is 'outOfService' then the value of this object is '0'.

OBJECT-TYPE

The value of the object tFilterRPlcySNMPTestTableLastChg indicates the sysUpTime at the time of the last modification of tFilterRPlcySNMPTestTable. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The object tFilterRPlcySNMPTestTable contains a list of all redirect policies' SNMP tests configured on this system.

OBJECT-TYPE

The object tFilterRPlcySNMPTestEntry contains information about a specific SNMP test. Entries are created/deleted by user. The entry can be created only if the value of the object tFltrRPDstAddrType is ipv4(1). Entries have a presumed StorageType of nonVolatile.

OBJECT-TYPE

The value of the object tFltrRPSnmpTest specifies the name of the SNMP test.

OBJECT-TYPE

The value of the object tFltrRPSnmpTLastChanged indicates the timestamp of last change of this row in tFilterRPlcySNMPTestTable.

OBJECT-TYPE

The value of the object tFltrRPSnmpTRowStatus specifies the status of the conceptual row in tFilterRPlcySNMPTestTable. Rows can be created and destroyed by SNMP SET operations on this object.

OBJECT-TYPE

The value of the object tFltrRPSnmpTOID specifies the OID of the object to be fetched from the destination.

OBJECT-TYPE

The value of the object tFltrRPSnmpTCommunity specifies the SNMPv1 or SNMPv2c Community String or the SNMPv3 Context Name used to conduct this SNMP test as described in RFC2571 and RFC2737. When the value of tFltrRPSnmpTSnmpVersion is 'snmpv1' or 'snmpv2c' this object represents a community string. When the value of tFltrRPSnmpTSnmpVersion is 'snmpv3' this object represents a SNMPv3 context name.

OBJECT-TYPE

The value of the object tFltrRPSnmpTSnmpVersion specifies the SNMP PDU format to be used while conducting the test. Currently only snmpv2c is supported.

OBJECT-TYPE

The value of the object tFltrRPSnmpTInterval specifies the amount of time in seconds between consecutive requests sent to the far end host.

OBJECT-TYPE

The value of the object tFltrRPSnmpTTimeout specifies the amount of time in seconds that is allowed for receiving a response from the far end host. If the response is not received within this time the far end host is considered unresponsive.

OBJECT-TYPE

The value of the object tFltrRPSnmpTDropCount specifies the number of consecutive requests that must fail for the destination to be declared unreachable.

OBJECT-TYPE

The value of the object tFltrRPSnmpTHoldDown specifies the amount of time in seconds that the system should be held down if this test has marked it unreachable.

OBJECT-TYPE

The value of the object tFltrRPSnmpTHoldDownRemain indicates the amount of time in seconds that the system will remain in held down state before being used again.

OBJECT-TYPE

The value of the object tFltrRPSnmpTLastActionTime indicates the time stamp when this test received a response for a probe sent out.

OBJECT-TYPE

The value of the object tFltrRPSnmpTLastOID indicates the OID received in the response.

OBJECT-TYPE

The value of the object tFltrRPSnmpTLastType indicates the type of the last received SNMP object. Value none(0) indicates that no object was received. Value 'counter32' indicates that the value of SNMP object is of type Counter32. Value 'unsigned32' indicates that the value of SNMP object is of type Unsigned32. Value 'timeTicks' indicates that the value of SNMP object is of type timeTicks. Value 'integer32' indicates that the value of SNMP object is of type integer32. Value 'ipAddress' indicates that the value of SNMP object is of type ipAddress. Value 'octetString' indicates that the value of SNMP object is of type OCTET STRING. Value 'objectId' indicates that the value of SNMP object is of type OBJECT IDENTIFIER. Value 'counter64' indicates that the value of SNMP object is of type Counter64. Value 'unsigned32' indicates that the value of SNMP object is of type Unsigned32. Value 'opaque' indicates that the value of SNMP object is of type Opaque.

OBJECT-TYPE

The value of the object tFltrRPSnmpTLastCounter32Val indicates the value of an object received in the last test response, if the type of the received object is 'counter32'. When this object is set the value of the object tFltrRPSnmpTLastType is 'counter32'.

OBJECT-TYPE

The value of the object tFltrRPSnmpTLastUnsigned32Val indicates the value of an object received in the last test response, if the type of the received object is 'unsigned32'. When this object is set the value of the object tFltrRPSnmpTLastType is 'unsigned32'.

OBJECT-TYPE

The value of the object tFltrRPSnmpTLastTimeTicksVal indicates the value of an object received in the last test response, if the type of the received object is 'timeTicks'. When this object is set the value of the object tFltrRPSnmpTLastType is 'timeTicks'.

OBJECT-TYPE

The value of the object tFltrRPSnmpTLastInt32Val indicates the value of an object received in the last test response, if the type of the received object is 'integer32'. When this object is set the value of the object tFltrRPSnmpTLastType is 'integer32'.

OBJECT-TYPE

The value of the object tFltrRPSnmpTLastOctetStringVal indicates the value of an object received in the last test response, if the type of the received object is 'octetString'. When this object is set the value of the object tFltrRPSnmpTLastType is 'octetString'.

OBJECT-TYPE

The value of the object tFltrRPSnmpTLastIpAddressVal indicates the value of an object received in the last test response, if the type of the received object is 'ipAddress'. When this object is set the value of the object tFltrRPSnmpTLastType is 'ipAddress'. This object is used only for IPv4 addresses. IPv6 addresses are represented using TAddress or InetAddress, and so the underlying datatype is OCTET STRING, and their value would be stored in the tFltrRPSnmpTLastOctetStringVal column.

OBJECT-TYPE

The value of the object tFltrRPSnmpTLastOidVal indicates the value of an object received in the last test response, if the type of the received object is 'objectId'. When this object is set the value of the object tFltrRPSnmpTLastType is 'objectId'.

OBJECT-TYPE

The value of the object tFltrRPSnmpTLastCounter64Val indicates that the value of an object received in the last test response, if the type of the received object is 'counter64'. When this object is set the value of the object tFltrRPSnmpTLastType is 'counter64'.

OBJECT-TYPE

The value of the object tFltrRPSnmpTLastOpaqueVal indicates the value of an object received in the last test response, if the type of the received object is 'opaque'. When this object is set the value of the object tFltrRPSnmpTLastType is 'opaque'.

OBJECT-TYPE

The value of the object tFltrRPSnmpTLastAction indicates an impact that the last test probe had on the value of the object tFltrRPDstOperState. If the value is 'disable', the destination may not be used for tFltrRPSnmpTHoldDown seconds.

OBJECT-TYPE

The value of the object tFltrRPSnmpTLastPrioChange indicates the priority change that the last test probe made to the operational priority of the destination. This object is significant only if the value of the object tFltrRPSnmpTLastAction is 'enable'. Otherwise it has no significance and it's holding the value '0'.

OBJECT-TYPE

The value of the object tFltrRPSnmpTNextRespIndex indicates the next response index to be used while creating a row in the tFilterRPlcySNMPRespTable. The value of '-1' means that the maximum number of return values for this OID is already configured.

OBJECT-TYPE

The value of the object tFilterRPlcySNMPRespTableLastChg indicates the sysUpTime at the time of the last modification of tFilterRPlcySNMPRespTable. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

Each row in this table holds the effect of the test on the destination for a specific return value. Each row is created once and cannot be modified after creation. Any change attempts will be silently discarded.

OBJECT-TYPE

Information about action to be taken for a specific destination when a specific response is received. Each row is created once and cannot be modified after creation. Any change attempts will be silently discarded.

OBJECT-TYPE

The value of the object tFltrRPSnmpRspId indicates the ID of the response entry.

OBJECT-TYPE

The value of the object tFltrRPSnmpRspLastChanged indicates the timestamp of last change of this row in tFilterRPlcySNMPRespTable.

OBJECT-TYPE

The value of the object tFltrRPSnmpRspRowStatus specifies the status of the conceptual row in tFilterRPlcySNMPRespTable. Rows can be created and destroyed by SNMP SET operations on this object.

OBJECT-TYPE

The value of the object tFltrRPSnmpRspAction specifies the action which will be taken on the operational priority of a destination (tFilterRDOperPriority), if the received object OID and value matches the values defined in TFilterRPlcySNMPRespEntry. This object cannot be modified after creation.

OBJECT-TYPE

The value of the object tFltrRPSnmpRspPrioChange specifies the offset to be applied to the destination base priority (tFilterRDAdminPriority) in order to compute the tFilterRDOperPriority as a result of this test, if the tFltrRPSnmpRspAction is either 'increase' or 'decrease'. This object cannot be modified after creation.

OBJECT-TYPE

The value of the object tFltrRPSnmpRspOID specifies the OID to be received in the response. This field cannot be modified after creation.

OBJECT-TYPE

The value of the object tFltrRPSnmpRspType specifies the type of the SNMP object to be received. Note: types 'objectId' and 'counter64' are not supported for now, and will be rejected when used. This object cannot be modified after creation. Any change attempts will be silently discarded. Value 'counter32' indicates that the value of SNMP object is of type Counter32. Value 'unsigned32' indicates that the value of SNMP object is of type Unsigned32. Value 'timeTicks' indicates that the value of SNMP object is of type timeTicks. Value 'integer32' indicates that the value of SNMP object is of type integer32. Value 'ipAddress' indicates that the value of SNMP object is of type ipAddress. Value 'octetString' indicates that the value of SNMP object is of type OCTET STRING. Value 'objectId' indicates that the value of SNMP object is of type OBJECT IDENTIFIER. Value 'counter64' indicates that the value of SNMP object is of type Counter64. Value 'unsigned32' indicates that the value of SNMP object is of type Unsigned32. Value 'opaque' indicates that the value of SNMP object is of type Opaque.

OBJECT-TYPE

The value of the object tFltrRPSnmpRspCounter32Val specifies the value of type Counter32 which the object received in the test response should have in order to pass the test. When this value is specified the value of the object tFltrRPSnmpRspType should be set to 'counter32'. This field cannot be modified after creation. Any change attempts will be silently discarded.

OBJECT-TYPE

The value of the object tFltrRPSnmpRspUnsigned32Val specifies the value of type Unsigned32 which the object received in the test response should have in order to pass the test. When this value is specified the value of the object tFltrRPSnmpRspType should be set to 'unsigned32'. This field cannot be modified after creation. Any change attempts will be silently discarded.

OBJECT-TYPE

The value of the object tFltrRPSnmpRspTimeTicksVal specifies the value of type TimeTicks which the object received in the test response should have in order to pass the test. When this value is specified the value of the object tFltrRPSnmpRspType should be set to 'timeTicks'. This field cannot be modified after creation. Any change attempts will be silently discarded.

OBJECT-TYPE

The value of the object tFltrRPSnmpRspInt32Val specifies the value of type Integer32 which the object received in the test response should have in order to pass the test. When this value is specified the value of the object tFltrRPSnmpRspType should be set to 'integer32'. This field cannot be modified after creation. Any change attempts will be silently discarded.

OBJECT-TYPE

The value of the object tFltrRPSnmpRspOctetStringVal specifies the value of type OCTET STRING which the object received in the test response should have in order to pass the test. When this value is specified the value of the object tFltrRPSnmpRspType should be set to 'octetString'. This field cannot be modified after creation. Any change attempts will be silently discarded.

OBJECT-TYPE

The value of the object tFltrRPSnmpRspIpAddressVal specifies the IPv4 address which the object received in the test response should have in order to pass the test. When this value is specified the value of the object tFltrRPSnmpRspType should be set to 'ipAddress'. IPv6 addresses are represented using TAddress or InetAddress, and so the underlying data type is OCTET STRING, and their value would be stored in the tFltrRPSnmpRspOctetStringVal column. This field cannot be modified after creation. Any change attempts will be silently discarded.

OBJECT-TYPE

The value of the object tFltrRPSnmpRspOidVal specifies the OID which the object received in the test response should have in order to pass the test. When this value is specified the value of the object tFltrRPSnmpRspType should be set to 'objectId'. This field cannot be modified after creation. Any change attempts will be silently discarded.

OBJECT-TYPE

The value of the object tFltrRPSnmpRspCounter64Val specifies the value of type Counter64 which the object received in the test response should have in order to pass the test. When this value is specified the value of the object tFltrRPSnmpRspType should be set to 'counter64'. This field cannot be modified after creation. Any change attempts will be silently discarded.

OBJECT-TYPE

The value of the object tFltrRPSnmpRspOpaqueVal specifies the value of type Opaque which the object received in the test response should have in order to pass the test. When this value is specified the value of the object tFltrRPSnmpRspType should be set to 'opaque'. This field cannot be modified after creation. Any change attempts will be silently discarded.

OBJECT-TYPE

The value of the object tFilterRPlcyURLTestTableLastChg indicates the sysUpTime at the time of the last modification of tFilterRPlcyURLTestTable. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

This table contains a list of all redirect URL tests configured on this system.

OBJECT-TYPE

Information about a specific URL test configured for a destination. Entries are created/deleted by user. The entry can be created only if the value of the object tFltrRPDstAddrType is ipv4(1). Entries have a presumed StorageType of nonVolatile.

OBJECT-TYPE

The value of the object tFltrRPUrlTest specifies the name of the URL test.

OBJECT-TYPE

The value of the object tFltrRPUrlTLastChanged indicates the timestamp of last change of this row in tFilterRPlcyURLTestTable.

OBJECT-TYPE

The value of the object tFltrRPUrlTRowStatus specifies the status of the conceptual row in tFilterRPlcyURLTestTable. Rows in tFilterRPlcyURLTestTable can be created and destroyed by SNMP SET operations on this object.

OBJECT-TYPE

The value of the object tFltrRPUrlTUrl specifies the URL to be probed.

OBJECT-TYPE

The value of the object tFltrRPUrlTHttpVersion specifies HTTP Version to be used while performing the URL test. The system by default uses HTTP Version 1.1 until explicitly specified.

OBJECT-TYPE

The value of the object tFltrRPUrlTInterval specifies the amount of time in seconds between consecutive requests sent to the far end host.

OBJECT-TYPE

The value of the object tFltrRPUrlTTimeout specifies the amount of time in seconds that is allowed for receiving a response from the far end host. If the response is not received within this time the far end host is considered unresponsive.

OBJECT-TYPE

The value of the object tFltrRPUrlTDropCount specifies the number of consecutive requests that must fail for the destination to be declared unreachable.

OBJECT-TYPE

The value of the object tFltrRPUrlTHoldDown specifies the amount of time in seconds that the system should be held down this test has marked it unreachable.

OBJECT-TYPE

The value of the object tFltrRPUrlTHoldDownRemain indicates the amount of time in seconds that the system will remain in held down state before being used again.

OBJECT-TYPE

The value of the object tFltrRPUrlTLastActionTime indicates the time stamp when this test received a response for a probe sent out.

OBJECT-TYPE

The value of the object tFltrRPUrlTLastRetCode indicates the return code received in the last response.

OBJECT-TYPE

The value of the object tFltrRPUrlTLastAction indicates impact that the last test probe had on the operational status of the destination as maintained in tFilterRDOperState. If the last action was 'disable', the destination may not be used for tFltrRPUrlTHoldDown seconds.

OBJECT-TYPE

The value of the object tFltrRPUrlTLastPrioChange indicates the priority change that the last test probe made to the operational priority of the destination. This object is significant only if the value of the object tFltrRPUrlTLastAction is 'enable'. Otherwise it has no significance and it's holding the value '0'.

OBJECT-TYPE

The value of the object tFilterRPlcyURLRespTableLastChg indicates the sysUpTime at the time of the last modification of tFilterRPlcyURLRespTable. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

Each row in this table specifies the effect of the test on the destination for a range of return values.

OBJECT-TYPE

Entry contains information about an action to be taken for a specific destination when a return value within the range specifies by tFltrRPUrlTRspLowRspCode and tFltrRPUrlTRspHighRspCode is received.

OBJECT-TYPE

The value of the object tFltrRPUrlTRspLowRspCode specifies the lower return code of the range specified by this entry.

OBJECT-TYPE

The value of the object tFltrRPUrlTRspHighRspCode specifies the higher return code of the range specified by this entry.

OBJECT-TYPE

The value of the object tFltrRPUrlTRspLastChanged indicates the timestamp of last change of this row in tFilterRPlcyURLRespTable.

OBJECT-TYPE

The value of the object tFltrRPUrlTRspRowStatus specifies the status of the conceptual row in tFilterRPlcyURLRespTable. Rows can be created and destroyed by SNMP SET operations on this object.

OBJECT-TYPE

The value of the object tFltrRPUrlTRspAction specifies the action which will be taken on the operational priority of a destination (tFilterRDOperPriority), if the received object OID and value matches the values defined in TFilterRPlcySNMPRespEntry.

OBJECT-TYPE

If the tFltrRPUrlTRspAction is either 'increase' or 'decrease', the value of the object tFltrRPUrlTRspPrioChange specifies the offset to be applied to the destination base priority (tFilterRDAdminPriority) in order to compute the tFilterRDOperPriority as a result of this test.

OBJECT-TYPE

The value of the object tFilterRPlcyPingTestTableLastChg indicates the sysUpTime at the time of the last modification of tFilterRPlcyPingTestTable. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The table tFilterRPlcyPingTestTable contains a list of all redirect Ping tests configured on this system.

OBJECT-TYPE

Entry contains information about a specific Ping test. Entries are created/deleted by user and have a presumed StorageType of nonVolatile.

OBJECT-TYPE

The value of the object tFltrRPPingTLastChanged indicates the timestamp of last change of this row in tFilterRPlcyPingTestTable.

OBJECT-TYPE

The value of the object tFltrRPPingTRowStatus specifies the status of the conceptual row in tFilterRPlcyPingTestTable. Rows are created and destroyed by SNMP SET operations on this object.

OBJECT-TYPE

The value of the object tFltrRPPingTInterval specifies the amount of time in seconds between consecutive requests sent to the far end host. Note that the value of tFltrRPPingTInterval can only be modified if the value of the corresponding tFilterRPAdminState and/or tFltrRPDstAdminState object is outOfService.

OBJECT-TYPE

The value of the object tFltrRPPingTTimeout specifies the amount of time in seconds that is allowed for receiving a response from the far end host. If a reply is not received within this time the far end host is considered unresponsive. Note that the value of tFltrRPPingTTimeout can only be modified if the value of the corresponding tFilterRPAdminState and/or tFltrRPDstAdminState object is outOfService.

OBJECT-TYPE

The value of the object tFltrRPPingTDropCount specifies the number of consecutive requests that must fail for the destination to be declared unreachable.

OBJECT-TYPE

The value of the object tFltrRPPingTHoldDown specifies the amount of time in seconds that the system should be held down if any of the test has marked it unreachable.

OBJECT-TYPE

The value of the object tFltrRPPingTHoldDownRemain indicates the amount of time in seconds that the system will remain in held down state before being used again.

OBJECT-TYPE

The value of the object tFltrRPPingTLastActionTime maintains the time stamp when this test received a response for a probe sent out.

OBJECT-TYPE

The value of the object tFltrRPPingTLastAction maintains impact that the last test probe made on the operational status of the destination as maintained in tFltrRPDstOperState. If the last action was 'disable', the destination may not be used for tFilterRPTHoldDown seconds.

OBJECT-TYPE

The value of the object tFilterRPPingSrcAddressAddrType indicates the context in which the values of the objects tFilterRPPingSrcAddressAddr are interpreted. Only following values are supported: unknown(0) ipv4(1) ipv6(2) The value 'unknown' indicates IP address type is not specified. The non zero value of tFilterRPPingSrcAddressAddrType must be set together with non zero values of tFilterRPPingSrcAddressAddr.

OBJECT-TYPE

The value of the object tFilterRPPingSrcAddressAddr indicates the source IP address to use in the ping test. The value should be a router local address to make sure the reply reaches the CPM. The value must be consistent with the IP version value of the associated tFilterRPActiveDestAddrType object.

OBJECT-TYPE

The value of the object tFilterRPlcyUcastRtTTableLastChg indicates the sysUpTime at the time of the last modification of tFilterRPlcyUnicastRtTestTable. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The table tFilterRPlcyUnicastRtTestTable contains list of all Unicast Route Reachability tests configured on this system.

OBJECT-TYPE

Entry contains information about a specific Unicast Route Reachability test configured for a destination in a Redirect Policy. There can be only one Unicast Route Reachability test configured per destination. Upon creation of the entry the IP address of the destination specified by the values of the objects tFltrRPDstAddrType and tFltrRPDstAddr and optionally (if not equal to the default value) the virtual router instance ID specified by the value of the object tFilterRPVrtrId is registered with RTM module. Redirect policy is then informed about any change of the reachability of the destination (based on availability of a route in a particular routing table) and modifies the value of the object tFltrRPDstOperState accordingly. An entry in the table tFilterRPlcyUnicastRtTestTable is created and destroyed by SNMP SET operations on the object tFltrRPUcastRtTRowStatus.

OBJECT-TYPE

The value of the object tFltrRPUcastRtTLastChanged indicates the timestamp of last change of this row in tFilterRPlcyUnicastRtTestTable.

OBJECT-TYPE

The value of the object tFltrRPUcastRtTRowStatus specifies the status of the conceptual row in tFilterRPlcyUnicastRtTestTable. Rows are created and destroyed by SNMP SET operations on this object.

OBJECT-TYPE

The value of the object tFltrRPUcastRtTLastActionTime indicates the time stamp when the last update from RTM module for this destination was received.

OBJECT-TYPE

The value of the object tFltrRPUcastRtTLastAction indicates an impact that the last message from RTM module had on the value of the object tFltrRPDstOperState.

OBJECT-TYPE

The value of the object tFilterSystemFilterTableLastChg indicates the sysUpTime at the time of the last modification of tFilterSystemFilterTable. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The table tFilterSystemFilterTable contains information pertaining to active IP and IPv6 system filter policies.

OBJECT-TYPE

An entry contains details about an active system filter policy. Only one active system filter policy per filter type can be configured in release 0.0. Upon creation of the entry the system filter policy identified by the values of the objects tFilterSystemFilterType and tFilterSystemFilterId is activated and downloaded to all line cards. Regular IP or IPv6 filter policies that have the value of the object tIPFilterChainToSystemFilter or tIPv6FilterChainToSystemFilter set to 'true(1)' are then chained to the active system filter policy. The system filter policy's rules are executed first before any rules of the regular filter policy are executed. An entry in the table tFilterSystemFilterTable is created and destroyed by SNMP SET operations on the object tFilterSystemFilterRowStatus. Furthermore an entry in the table tFilterSystemFilterTable is destroyed by the system if an entry with the same value of the object tFilterSystemFilterType is created so that there is always at most one entry for a given value of tFilterSystemFilterType.

OBJECT-TYPE

The value of the object tFilterSystemFilterType specifies the filter type of the system filter policy to be selected as the active system filter policy. Only values 'fltrtypeselIp(1)' and 'fltrtypeselIpv6(4)' are supported.

OBJECT-TYPE

The value of the object tFilterSystemFilterId specifies the ID of the filter policy to be selected as the active system filter policy. Values outside of range 1..65535 are reserved for entries dynamically created by the system and cannot be used in any SNMP SET operation. If the value of the object tFilterSystemFilterType is 'fltrtypeselIp(1)' then the filter policy with the specified ID must exist in tIPFilterTable and must have scope 'system(4)' configured as the value of the object tIPFilterScope. If the value of the object tFilterSystemFilterType is 'fltrtypeselIpv6(4)' then the filter policy with the specified ID must exist in tIPv6FilterTable and must have scope 'system(4)' configured as the value of the object tIPv6FilterScope.

OBJECT-TYPE

The value of the object tFilterSystemFilterLastChanged indicates the timestamp of the last change of this row in tFilterSystemFilterTable.

OBJECT-TYPE

The value of the object tFilterSystemFilterRowStatus specifies the status of the conceptual row in tFilterSystemFilterTable. Rows are created and destroyed by SNMP SET operations on this object. Only values 'active(1)', 'createAndGo(4)' and 'destroy(6)' are supported. If a row for the same filter type specified by the value of the object tFilterSystemFilterType already exists in the table and a new row with a different value of the object tFilterSystemFilterId is being created the original row is removed by the system.

OBJECT-TYPE

The value of tDhcp6FilterTblLastChanged indicates the sysUpTime at the time of the last modification to tDhcp6FilterTable by adding, deleting an entry or change to a writable object in the table. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

Contains a list of all DHCP6 filters configured on this system.

OBJECT-TYPE

Information about a particular DHCP6 filter. Entries are created/deleted by user. Entries have a presumed StorageType of nonVolatile.

OBJECT-TYPE

Uniquely identifies a DHCP6 filter as configures on this system.

OBJECT-TYPE

This object allows entries to be created and deleted in the tDhcp6FilterTable.

OBJECT-TYPE

Indicates the timestamp of the last change to this row.

OBJECT-TYPE

User-provided description for this filter.

OBJECT-TYPE

The default action to take for DHCP6 host creation requests that do not match any of this filter's entries. The value none(1) specifies normal host creation behaviour, the value bypass-host-creation(2) specifies to bypass host creation, the value drop(3) specifies to drop the DHCP6 message.

OBJECT-TYPE

The value of the object tDhcp6FilterDefActionFlags specifies for which types of DHCPv6 IAs the bypass-host-creation action is applied.

OBJECT-TYPE

The value of tDhcp6FilterParamsTblLastChanged indicates the sysUpTime at the time of the last modification to tDhcp6FilterParamsTable by adding, deleting an entry or change to a writable object in the table. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

A table of all DHCP6 filter match entries for all DHCP6 filters

OBJECT-TYPE

Information about a particular DHCP6 filter entry. Every DHCP6 filter can have zero or more DHCP6 filter match entries. A filter entry with no match criteria set will match every packet, and the entry action will be taken. Entries are created/deleted by user. There is no StorageType object, entries have a presumed StorageType of nonVolatile.

OBJECT-TYPE

This is the secondary index for the entry. Every DHCP6 filter can have multiple entries, therefore every DHCP6 filter entry is identified by the tDhcp6FilterId and tDhcp6FilterParamsId.

OBJECT-TYPE

This object allows entries to be created and deleted in the tDhcp6FilterParamsTable.

OBJECT-TYPE

Indicates the timestamp of the last change to this row.

OBJECT-TYPE

The value of tDhcp6FilterParamsOptionNumber specifies the number of the DHCP6 option to filter on.

OBJECT-TYPE

The value of tDhcp6FilterParamsOptionMatch specifies the criteria that the DHCP6 option must match to trigger this filter entry. The value present(1) specifies that the DHCP6 option must be present, the value absent(2) specifies that the DHCP6 option must be absent. In these cases tDhcp6FilterParamsOptionValue will be reset to an empty string. A value string(3), string-exact(4), string-invert(5), string-exact-invert(6), hex(7), hex-exact(8), hex-invert(9) or hex-exact-invert(10) requires an octet string to be present in tDhcp6FilterParamsOptionValue to match against.

OBJECT-TYPE

The action to take for DHCP6 host creation requests that match this filter entry. The value none(1) specifies normal host creation behaviour, the value bypass-host-creation(2) specifies to bypass host creation, the value drop(3) specifies to drop the DHCP6 message.

OBJECT-TYPE

The value of the object tDhcp6FilterParamsOptionValue specifies the matching pattern for the filtered DHCP6 option. This object is mandatory at creation time. A zero length value is only allowed when the value of tDhcp6FilterParamsOptionMatch is present(1) or absent(2).

OBJECT-TYPE

The value of the object tDhcp6FilterParamsActionFlags specifies for which types of DHCPv6 IAs the bypass-host-creation action is applied.

OBJECT-TYPE

The value of the object tFilterEmbedFlowspecTableLstChg indicates the sysUpTime at the time of the last modification of tFilterEmbedFlowspecTable. If no changes were made to the table since the last re-initialization of the local network management subsystem, this object contains the value zero.

OBJECT-TYPE

The table tFilterEmbedFlowspecTable contains an entry for each set of flowspec rules embedded in an IP or IPv6 filter with scope other than 'embedded'.

OBJECT-TYPE

An entry in the table tFilterEmbedFlowspecTable. Entries in this table can be created and deleted via SNMP SET operations to tFilterEmbedFlowspecRowStatus. Moreover entries are automatically created and deleted by the system when a set of flowspec rules is embedded into a filter managed by a VSD controller.

OBJECT-TYPE

The value of the object tFilterEmbedFlowspecFilterType specifies the type of filter, either IPv4 or IPv6, for the filter specified by tFilterEmbedFlowspecInsertFltrId.

OBJECT-TYPE

The value of the object tFilterEmbedFlowspecInsertFltrId specifies the filter where the set of flowspec rules configured for the virtual router specified by tFilterEmbedFlowspecRtrId is to be embedded. Values outside of range 1..65535 are reserved for entries dynamically created by the system and cannot be used in any SNMP SET operation.

OBJECT-TYPE

The value of the object tFilterEmbedFlowspecOffset specifies the offset of inserted flowspec entries.

OBJECT-TYPE

The value of the object tFilterEmbedFlowspecRowStatus specifies the status of a row in tFilterEmbedFlowspecTable. Rows are created and destroyed by SNMP SET operations on this object. Only values 'active (1)', 'createAndGo(4)', and 'destroy (6)' are supported.

OBJECT-TYPE

The value of tFilterEmbedFlowspecLastChanged indicates the sysUpTime at the time of last change to this row in tFilterEmbedFlowspecEntry.

OBJECT-TYPE

The value of the object tFilterEmbedFlowspecRtrId specifies a virtual router for which a set of flowspec rules have been configured by an external system. Such flowspec rules will be embedded into the embedding filter specified by tFilterEmbedFlowspecFilterType and tFilterEmbedFlowspecInsertFltrId. At the time of creation of a row via SNMP you can either specify or not specify a value for tFilterEmbedFlowspecRtrId. If you do not specify the value of tFilterEmbedFlowspecRtrId then the system will try to obtain it. This corresponds to the situation when the embedding filter has already been assigned to any endpoint. If you do not specify the value of tFilterEmbedFlowspecRtrId and the embedding filter has not been assigned to any endpoint yet then the creation of the row will fail. If you specify the value of tFilterEmbedFlowspecRtrId then the system will check if the embedding filter has already been assigned to any endpoint. If this is not the case it will not be possible to assign the embedding filter outside the scope of the virtual router specified by tFilterEmbedFlowspecRtrId. If this is the case then the creation of the row may be successful only if the value of the virtual router specified by tFilterEmbedFlowspecRtrId matches with the value already stored in the system. In any case the value of tFilterEmbedFlowspecRtrId cannot be changed after creation of the row.

OBJECT-TYPE

The value of the object tFilterEmbedFlowspecAdminState specifies the administrative state of the embed request defined by this row. If an active embedding cannot be fulfilled due to dynamic events, this object will be set to 'inactive' automatically by the system. In those cases, the value of the object tFilterEmbedFlowspecOperState will indicate the failure reason.

OBJECT-TYPE

The value of tFilterEmbedFlowspecOperState indicates the operational state of the embed request defined by this row.

OBJECT-TYPE

The value of the object tFilterEmbedFlowspecGroupId specifies the group id that is used to select subset of flowspec rules and embed only those rules. Value of 65535 means insert all rules irregardless of their group id

OBJECT-TYPE

The table tFltrEmbFlowspecInfoTable contains an entry for each auto-created embedded filter for flowspec rules inserted in an IP or IPv6 filter with scope other than 'embedded'. This row complements the corresponding row in the tFilterEmbedFlowspecTable with read-only operational info.

OBJECT-TYPE

An entry in the tFltrEmbFlowspecInfoTable.

OBJECT-TYPE

The value of the object tFltrEmbFlowSpecInfoFltrId indicates the ID of the auto-created embedded filter for flowspec rules related to the virtual router specified by tFilterEmbedFlowspecRtrId.

OBJECT-TYPE

The value of the object tFltrEmbFlowSpecInfoEntryCnt indicates how many entries are present in the embedded filter specified by tFltrEmbFlowSpecInfoFltrId.

OBJECT-TYPE

The value of the object tFltrEmbFlowSpecInfoEntryCntIns indicates how many entries of the embedded filter (specified by tFltrEmbFlowSpecInfoFltrId) are actually inserted into the embedding filter (specified by tFilterEmbedFlowspecInsertFltrId). If the object tFilterEmbedFlowspecOperState is different from 'active' this object will always be zero. Otherwise the difference between tFltrEmbFlowSpecInfoEntryCnt and the value of this object indicates how many entries of the embedded filter were overwritten by local entries in the embedding filter.

OBJECT-TYPE

The table tFltrEmbFlowspecEntryInfoTable contains an entry for each entry of an auto-created embedded filter for flowspec rules inserted in an IP or IPv6 filter with scope other than 'embedded'. This table shows only basic flowspec embeddings (no support for groups). Will be obsoleted in the next release. Please use tFilterEmbFlowspecEntryInfoTable instead.

OBJECT-TYPE

An entry in the tFltrEmbFlowspecEntryInfoTable. Rows in the tFltrEmbFlowspecEntryInfoTable are created by the SYSTEM when an auto-created embedded filter for flowspec rules is inserted into an IP or IPv6 filter with scope other than 'embedded'. They are destroyed by the SYSTEM when such auto-created embedded filter is removed from an IP or IPv6 filter with scope other than 'embedded'.

OBJECT-TYPE

The value of the object tFltrEmbFlowspecEntryId specifies the ID of the entry inside of the auto-created embedded filter for flowspec rules specified by tFltrEmbFlowSpecInfoFltrId.

OBJECT-TYPE

The value of the object tFltrEmbFlowspecEntryInsEntryId indicates which entry in the IP or IPv6 filter with scope other than 'embedded' specified by tFilterEmbedFlowspecInsertFltrId corresponds to the entry specified by tFltrEmbFlowspecEntryId in the auto-created embedded filter for flowspec rules specified by tFltrEmbFlowSpecInfoFltrId.

OBJECT-TYPE

The value of the object tFltrEmbFlowspecEntryOperState indicates the current operational state of the entry identified by tFltrEmbFlowspecEntryId of the embedded filter identified by tFltrEmbFlowSpecInfoFltrId that is embedded into the filter identified by tFilterEmbedFlowspecInsertFltrId.

OBJECT-TYPE

The value of the object tFilterEmbedVsdTableLstChg indicates the sysUpTime at the time of the last modification of tFilterEmbedVsdTable. If no changes were made to the table since the last re-initialization of the local network management subsystem, this object contains the value zero.

OBJECT-TYPE

The table tFilterEmbedVsdTable contains an entry for each filter managed by a VSD controller embedded in a filter with scope other than 'embedded'. A dedicated embedded filter under the management of the VSD controller contains all required dynamic steering rules. This set of rules is inserted into a filter (that has scope other than 'embedded') created by an administrator containing static (security) rules that is applied on interfaces. This way the administrator has full control of the position (offset) at which the rules are inserted in order not to compromise security while the VSD controller can dynamically alter the steering rules as necessary.

OBJECT-TYPE

An entry in the table tFilterEmbedVsdTable. Entries in this table can be created and deleted via SNMP SET operations to tFilterEmbedVsdRowStatus. Moreover entries are automatically created and deleted by the system when one filter managed by a VSD controller is embedded into another filter managed by a VSD controller.

OBJECT-TYPE

The value of the object tFilterEmbedVsdFilterType specifies the type of filter for the filters specified by tFilterEmbedVsdEmbeddedFltrId and tFilterEmbedVsdInsertFltrId. In release 14.0 only values 'fltrtypeselIp (1)', 'fltrtypeselMac (2)' and 'fltrtypeselIpv6 (4)' are supported.

OBJECT-TYPE

The value of the object tFilterEmbedVsdInsertFltrId specifies the ID of the filter with scope other than 'embedded' where the filter managed by a VSD controller specified by tFilterEmbedVsdEmbeddedFltrId is to be inserted. Values outside of range 1..65535 are reserved for entries dynamically created by the system and cannot be used in any SNMP SET operation.

OBJECT-TYPE

The value of the object tFilterEmbedVsdEmbeddedFltrId specifies the ID of the filter managed by a VSD controller to be inserted in the filter with scope other than 'embedded' specified by tFilterEmbedVsdInsertFltrId.

OBJECT-TYPE

The value of the object tFilterEmbedVsdOffset specifies the offset of inserted entries.

OBJECT-TYPE

The value of the object tFilterEmbedVsdRowStatus specifies the status of a row in tFilterEmbedVsdTable. Rows are created and destroyed by SNMP SET operations on this object. Only values 'active (1)', 'createAndGo(4)', and 'destroy (6)' are supported.

OBJECT-TYPE

The value of tFilterEmbedVsdLastChanged indicates the sysUpTime at the time of last change to this row in tFilterEmbedVsdTable.

OBJECT-TYPE

The value of the object tFilterEmbedVsdAdminState specifies the administrative state of the embed request defined by this row. If an active embedding cannot be fulfilled due to dynamic events, this object will be set to 'inactive' automatically by the system. In those cases, the value of the object tFilterEmbedVsdOperState will indicate the failure reason.

OBJECT-TYPE

The value of the object tFilterEmbedVsdOperState indicates the operational state of the embed request defined by this row.

OBJECT-TYPE

The table tFilterEmbedVsdInfoTable contains an entry for each embedded filter managed by a VSD controller inserted in a filter with scope other than 'embedded'. This row complements the corresponding row in the tFilterEmbedVsdTable with read-only operational info.

OBJECT-TYPE

An entry in the tFilterEmbedVsdInfoTable.

OBJECT-TYPE

The value of the object tFltrEmbedVsdInfoEntryCnt indicates how many entries are present in the embedded filter managed by a VSD controller (specified by tFilterEmbedVsdEmbeddedFltrId).

OBJECT-TYPE

The value of the object tFltrEmbedVsdInfoEntryCntInsrtd indicates how many entries of the embedded filter managed by a VSD controller (specified by tFilterEmbedVsdEmbeddedFltrId) are actually inserted into the embedding filter (specified by tFilterEmbedVsdInsertFltrId). If the object tFilterEmbedVsdOperState is different from 'active' this object will always be zero. Otherwise the difference between the value of this object and the value of tFltrEmbedVsdInfoEntryCnt indicates how many entries of the embedded filter were overwritten by local entries in the embedding filter.

OBJECT-TYPE

The table tFilterEmbedVsdEntryInfoTable contains an entry for each entry of an embedded filter managed by a VSD controller inserted in a filter with scope other than 'embedded'

OBJECT-TYPE

An entry in the tFilterEmbedVsdEntryInfoTable. Rows in the tFilterEmbedVsdEntryInfoTable are created by the SYSTEM when an embedded filter managed by a VSD controller is inserted into a filter with scope other than 'embedded'. They are destroyed by the SYSTEM when an embedded filter managed by a VSD controller is removed from a filter with scope other than 'embedded'.

OBJECT-TYPE

The value of the object tFilterEmbedVsdEntryId specifies the ID of the entry inside of the embedded filter managed by a VSD controller specified by tFilterEmbedVsdEmbeddedFltrId.

OBJECT-TYPE

The value of the object tFilterEmbedVsdEntryInsrtEntryId indicates which entry in the filter with scope other than 'embedded' specified by tFilterEmbedVsdInsertFltrId corresponds to the entry specified by tFilterEmbedVsdEntryId in the filter managed by a VSD controller specified by tFilterEmbedVsdEmbeddedFltrId.

OBJECT-TYPE

The value of the object tFilterEmbedVsdEntryOperState indicates the current operational state of the entry identified by tFilterEmbedVsdEntryId of the embedded filter identified by tFilterEmbedVsdEmbeddedFltrId that is embedded into the filter identified by tFilterEmbedVsdInsertFltrId.

OBJECT-TYPE

The value of the object tMacFltrEntryActionTblLChg indicates the sysUpTime at the time of the last modification of tMacFltrEntryActionTable. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The table tMacFltrEntryActionTable contains information pertaining to redundant MAC filter entry actions. Prior to introduction of tMacFltrEntryActionTable MAC filter actions were configured via tMacFilterParamsTable. Via tMacFilterParamsTable it is possible to configure only one action per filter entry. tMacFltrEntryActionTable is introduced to override the functionality of tMacFilterParamsTable regarding the action configuration. tMacFltrEntryActionTable supports configuration of redundant filter actions. Functionality related to actions added after introduction of tMacFltrEntryActionTable is supported only via tMacFltrEntryActionTable. Filter actions available prior to introduction of tMacFltrEntryActionTable can be configured via specifying action parameters in tMacFilterParamsTable or via tMacFltrEntryActionTable. It's recommended to use tMacFltrEntryActionTable. Configuration via tMacFilterParamsTable: - only actions available prior to introduction of tMacFltrEntryActionTable are allowed: When an entry is created in tMacFilterParamsTable then an entry with the value of tMacFltrEntryActActionId equal to 'primary' is created in tMacFltrEntryActionTable by the system. If an action is configured via tMacFilterParamsTable, then this new system created entry in tMacFltrEntryActionTable will contain interpretation of values pertaining to configured action in tMacFilterParamsEntry. Configuration via tMacFltrEntryActionTable: - action available prior to introduction of tMacFltrEntryActionTable: If an action which was available prior to introduction of tMacFltrEntryActionTable is configured via tMacFltrEntryActionTable and the value of tMacFltrEntryActActionId for that action is equal to 'primary' then the action related objects in the table tMacFilterParamsAction will be automatically set by the system to the interpretation of the values in tMacFltrEntryActionTable pertaining to that action. - action not available prior to introduction of tMacFltrEntryActionTable: If an action not available prior to introduction of tMacFltrEntryActionTable is configured then the value of tMacFilterParamsAction is set to 'unrecognized' by the system. The value 'unrecognized' indicates that functionality not supported by tMacFilterParamsTable was configured and therefore action related objects in the tMacFilterParamsTable are not valid and shouldn't be used for configuration.

OBJECT-TYPE

The entry contains information pertaining to an action for a particular MAC filter entry (object corresponding to MAC filter entry is tMacFilterParamsEntry). Per one filter entry up to two actions can be configured (primary and secondary). Entries with the value of tMacFltrEntryActActionId equal to 'primary' are created and destroyed by SNMP SET operations on the object tMacFilterParamsRowStatus. Entries with the value of tMacFltrEntryActActionId equal to 'secondary' are created by SNMP SET operation on the object tMacFltrEntryActRowStatus and destroyed by SNMP SET operation on the objects tMacFltrEntryActRowStatus or tMacFilterParamsRowStatus.

OBJECT-TYPE

The value of the object tMacFltrEntryActActionId specifies a unique identifier of an action within the filter entry. Per one filter entry up to two actions can be configured (the primary and the secondary). PBF destination availability checking for an entry is turned on when both actions (the primary and the secondary) are configured for an entry. This is allowed only for the following combinations of actions: - both actions are PBF to SAP - both actions are PBF to SDP - the primary action is PBF to SAP and the secondary action is PBF to SDP or vice versa If the PBF destination of the primary action is available, then the primary action will be taken on a packet matching the filter entry. If the PBF destination of the primary action is not available and the PBF destination of the secondary action is available then the secondary action will be taken on a packet matching the filter entry. If none of the actions for the entry has an available PBF destination then the action specified by the object tMacFilterParamsPbrDwnActOvr will be taken on a packet matching the filter entry. There is a limit to the number of filter entries with the destination availability checking turned on.

OBJECT-TYPE

The value of the object tMacFltrEntryActLastChanged indicates the sysUpTime at the time of the last modification of tMacFltrEntryActionEntry. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The value of the object tMacFltrEntryActRowStatus specifies the status of the conceptual row in tMacFltrEntryActionTable. Rows with value of tMacFltrEntryActActionId equal to 'primary' are created and destroyed by SNMP SET operations on the object tMacFilterParamsRowStatus. Rows with value of tMacFltrEntryActActionId equal to 'secondary' are created by SNMP SET operation on the object tMacFltrEntryActRowStatus and destroyed by SNMP SET operation on the objects tMacFltrEntryActRowStatus or tMacFilterParamsRowStatus.

OBJECT-TYPE

The value of the object tMacFltrEntryActAction specifies the action to be taken on a packet matching the filter entry. Refer to the description of the textual convention TMacFilterEntryAction for more information.

OBJECT-TYPE

The value of the object tMacFltrEntryActFwdSapPortId specifies the sap port identity of the destination for this MAC filter entry. A value of 0 indicates that there is currently no SAP destination specified. A value different from 0 can only be specified if the value of tMacFltrEntryActAction is 'forwardSap' and the value of tMacFltrEntryActFwdSdpBind has a zero value. Note that the value of tMacFltrEntryActFwdSapPortId is silently cleared by the system if tMacFltrEntryActAction is set to value other than 'forwardSap'.

OBJECT-TYPE

The value of the object tMacFltrEntryActFwdSapEncapVal specifies the sap port encap value of the destination SAP for this MAC filter entry. A value different from 0 can only be specified when the tMacFltrEntryActFwdSapPortId object has a non zero value, and the value of the tMacFltrEntryActAction object of this entry is 'forwardSap'. A value of 0 indicates that either 1) the sap encapsulation value is not specified when tMacFltrEntryActFwdSapPortId and tMacFilterParamsFwdSvcId have valid values; or 2) that there is no SAP destination. Note that the value of tMacFltrEntryActFwdSapEncapVal is silently cleared by the system if tMacFltrEntryActAction is set to value other than 'forwardSap'.

OBJECT-TYPE

The value of the object tMacFltrEntryActFwdSdpBind specifies the sdp bind identity of the destination for this MAC filter entry. A value of 0 indicates that there is currently no SDP binding defined. A value different from 0 can only be specified if the value of tMacFltrEntryActAction is 'forwardSdp' and tMacFltrEntryActFwdSapPortId and tMacFltrEntryActFwdSapEncapVal have a zero value. Note that the value of tMacFltrEntryActFwdSdpBind is silently cleared by the system if tMacFltrEntryActAction is set to value other than 'forwardSdp'.

OBJECT-TYPE

The value of the object tMacFltrEntryActRedirectURL specifies the URL to redirect to, when the value of tMacFltrEntryActAction is 'httpRedirect'. Note that the value of tMacFltrEntryActRedirectURL is silently cleared by the system if tMacFltrEntryActAction is set to value other than 'httpRedirect'.

OBJECT-TYPE

The value of the object tMacFltrEntryActEsi specifies the ethernet segment identifier (ESI) of the first ESI identified appliance in Nuage service chain. When the value of tMacFilterParamsAction is 'forwardEsiL2' packets matching the filter entry are forwarded to the appliance using EVPN-resolved VXLAN tunnel in the specified VPLS service (tMacFltrEntryActFwdEsiSvcId). The value '0' indicates that there is no ESI specified. The non zero value of tMacFltrEntryActEsi must be set together with a non zero value of tMacFltrEntryActFwdEsiSvcId and value of tMacFltrEntryActAction set to 'forwardEsiL2'. Note that the value of tMacFltrEntryActEsi is silently cleared by the system if the value of tMacFltrEntryActAction is set to any value other than 'forwardEsiL2'.

OBJECT-TYPE

The value of the object tMacFltrEntryActFwdEsiSvcId specifies the identifier of the VPLS used for VPN/DC connectivity. The value '0' indicates that no VPLS identifier is specified. The non zero value of tMacFltrEntryActFwdEsiSvcId must be set together with a non zero value of tMacFltrEntryActEsi and value of tMacFltrEntryActAction set to 'forwardEsiL2'. Note that the value of tMacFltrEntryActFwdEsiSvcId is silently cleared by the system if the value of tMacFltrEntryActAction is set to any value other than 'forwardEsiL2'.

OBJECT-TYPE

The value of the object tMacFltrEntryActRateLimit specifies the rate to which the traffic matching the filter entry will be limited. The value of tMacFltrEntryActRateLimit can be set to non default value only if the value of tMacFltrEntryActAction is set to 'rateLimit'. Note that the value of tMacFltrEntryActRateLimit is silently cleared by the system if the value of tMacFltrEntryActAction is set to any value other than 'rateLimit'.

OBJECT-TYPE

The value of the object tMacFltrEntryActPbrTargetStatus indicates the PBR target status. Refer to the description of the textual convention TFilterPbrTargetStatus for more information.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActionTblLChg indicates the sysUpTime at the time of the last modification of tIPvXFltrEntryActionTable. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The table tIPvXFltrEntryActionTable contains information pertaining to redundant IPv4 and IPv6 filter entry actions. Prior to introduction of tIPvXFltrEntryActionTable IPv4 filter actions were configured via tIPFilterParamsTable and tIPFilterParamsExtTable. IPv6 filter actions were configured via tIPv6FilterParamsTable and tIPv6FilterParamsExtTable. Via these original tables it is possible to configure only one action per filter entry. tIPvXFltrEntryActionTable is introduced to override the functionality of the original tables regarding the action configuration. tIPvXFltrEntryActionTable supports configuration of redundant filter actions. Functionality related to actions added after introduction of tIPvXFltrEntryActionTable is supported only via tIPvXFltrEntryActionTable. Filter actions available prior to introduction of tIPvXFltrEntryActionTable can be configured via specifying action parameters in the original tables or via tIPvXFltrEntryActionTable. It's recommended to use tIPvXFltrEntryActionTable. Configuration via the original tables: - only actions available prior to introduction of tIPvXFltrEntryActionTable are allowed: When an entry is created in tIPFilterParamsTable then an entry with the value of tIPvXFltrEntryActActionId equal to 'primary' and the value of tIPvXFltrEntryActFltrType equal to 'fltrtypeselIp' is created in tIPvXFltrEntryActionTable by the system. When an entry is created in tIPv6FilterParamsTable then an entry with the value of tIPvXFltrEntryActActionId equal to 'primary' and the value of tIPvXFltrEntryActFltrType equal to 'fltrtypeselIpv6' is created in tIPvXFltrEntryActionTable by the system. This new system created entry in tIPvXFltrEntryActionTable will contain interpretation of values pertaining to configured action in tIPFilterParamsEntry or tIPv6FilterParamsEntry and their augment tables. Configuration via tIPvXFltrEntryActionTable: - action available prior to introduction of tIPvXFltrEntryActionTable: If an action which was available prior to introduction of tIPvXFltrEntryActionTable is configured via tIPvXFltrEntryActionTable and the value of tIPvXFltrEntryActActionId for that action is equal to 'primary' then the action related objects in the original tables will be automatically set by the system to the interpretation of the values in tIPvXFltrEntryActionTable pertaining to that action. - action not available prior to introduction of tIPvXFltrEntryActionTable: If an action not available prior to introduction of tIPvXFltrEntryActionTable is configured via tIPvXFltrEntryActionTable then the value of tIPFilterParamsAction (in case of IPv4 filter) or tIPv6FilterParamsAction (in case of IPv6 filter) is set to 'unrecognized' by the system. The value 'unrecognized' indicates that the functionality not supported by the original tables was configured and therefore action related objects in the original tables are not valid and shouldn't be used for configuration.

OBJECT-TYPE

The entry contains information pertaining to an action for a particular IPv4 or IPv6 filter entry (information pertaining to IPv4 filter entry is in tIPFilterParamsTable and tIPFilterParamsExtTable and information pertaining to IPv6 filter entry is in tIPv6FilterParamsTable and tIPv6FilterParamsExtTable). Per one filter entry up to two actions can be configured (primary and secondary). Entries with the value of tIPvXFltrEntryActActionId equal to 'primary' are created and destroyed by SNMP SET operations on the object tIPFilterParamsRowStatus or tIPv6FilterParamsRowStatus. Entries with the value of tIPvXFltrEntryActActionId equal to 'secondary' are created by SNMP SET operation on the object tIPvXFltrEntryActRowStatus and destroyed by SNMP SET operation on the object tIPvXFltrEntryActRowStatus, tIPFilterParamsRowStatus or tIPv6FilterParamsRowStatus.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActFltrType specifies the type of the filter to which this action belongs. Only values 'fltrtypeselIp' and 'fltrtypeselIpv6' are supported. Refer to the description of the textual convention TFilterType for more information.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActFltrId specifies the filter id of the filter to which this action belongs. The filter must exist in tIPFilterTable, if the value of tIPvXFltrEntryActFltrType is 'ipv4' or it must exist in tIPv6FilterTable if the value of tIPvXFltrEntryActFltrType is 'ipv6'. Refer to the description of the textual convention TAnyFilterID for more information.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActEntryId specifies the entry id of the entry to which this filter action belongs. The filter entry must exist in tIPFilterParamsTable, if the value of tIPvXFltrEntryActFltrType is 'ipv4' or it must exist in tIPv6FilterParamsTable if the value of tIPvXFltrEntryActFltrType is 'ipv6'.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActActionId specifies a unique identifier of an action within the filter entry. Per one filter entry up to two actions can be configured (the primary and the secondary). Destination availability checking is turned on when both actions (the primary and the secondary) are configured for an entry. This is allowed only for the following combinations of actions: - both actions are PBF to SAP - both actions are PBF to SDP - the primary action is PBF to SAP and the secondary action is forward SDP or vice versa - both actions are PBR to next-hop router If the PBR/PBF destination of the primary action is available, then the primary action will be taken on a packet matching the filter entry. If the PBR/PBF destination of the primary action is not available and the PBR/PBF destination of the secondary action is available then the secondary action will be taken on a packet matching the filter entry. If none of the actions for the entry has an available PBR/PBF destination then the action specified by the object tIPFilterParamsExtPbrDwnActOvr(for IPv4 filters) or tIPv6FilterParamsExtPbrDwnActOvr(for IPv6 filters) will be taken on a packet matching the filter entry. There is a limit to the number of entries with the destination availability checking turned on.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActLastChanged indicates the sysUpTime at the time of the last modification of tIPvXFltrEntryActionEntry. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActRowStatus specifies the status of the conceptual row in tIPvXFltrEntryActionTable. Rows with the value of tIPvXFltrEntryActActionId equal to 'primary' are created and destroyed by SNMP SET operations on the object tIPFilterParamsRowStatus or tIPv6FilterParamsRowStatus. Rows with the value of tIPvXFltrEntryActActionId equal to 'secondary' are created by SNMP SET operation on the object tIPvXFltrEntryActRowStatus and destroyed by SNMP SET operation on the object tIPvXFltrEntryActRowStatus, tIPFilterParamsRowStatus or tIPv6FilterParamsRowStatus.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActAction specifies the action to be taken on a packet matching the filter entry. Refer to the description of the textual convention TIPvXFilterEntryAction for more information.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActFwdNHIpAddrType specifies the context in which the value of the object tIPvXFltrEntryActFwdNHIpAddr is interpreted. Only following values are supported: unknown(0) ipv4(1) ipv6(2) The value of tIPvXFltrEntryActFwdNHIpAddrType must be consistent with the value of tIPvXFltrEntryActFltrType. Note that the value of tIPvXFltrEntryActFwdNHIpAddrType is silently cleared by the system if tIPvXFltrEntryActAction is set to value other than 'forwardNextHop' or 'forwardNextHopRtr'.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActFwdNHIpAddr specifies the IP/IPv6 address of the nexthop to which the packet should be forwarded if it hits this filter entry. The action of this entry should be 'forwardNextHop' or 'forwardNextHopRtr' in such a case. Note that the value of tIPvXFltrEntryActFwdNHIpAddr is silently cleared by the system if tIPvXFltrEntryActAction is set to value other than 'forwardNextHop' or 'forwardNextHopRtr'.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActFwdNHIndirect specifies if the nexthop is directly or indirectly reachable. The action of this entry should be 'forwardNextHop' or 'forwardNextHopRtr' in such a case. Note that the value of tIPvXFltrEntryActFwdNHIndirect is silently cleared by the system if tIPvXFltrEntryActAction is set to value other than 'forwardNextHop' or 'forwardNextHopRtr'.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActFwdNHInterface specifies the interface name for the nexthop to which the packet should be forwarded if it hits this filter entry. The action of this entry should be 'forwardNHInterface' in such a case. Note that the value of tIPvXFltrEntryActFwdNHInterface is silently cleared by the system if tIPvXFltrEntryActAction is set to value other than 'forwardNHInterface'.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActFwdRedPlcy specifies the redirect policy to be used to determine the nexthop. The action of this entry should be 'forwardRPlcy' in such a case. Note that the value of tIPvXFltrEntryActFwdRedPlcy is silently cleared by the system if tIPvXFltrEntryActAction is set to value other than 'forwardRPlcy'.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActFwdSapPortId specifies the sap port id of the destination for this filter entry. The value 0 indicates that there is no SAP destination defined. A value different from 0 can only be specified if the value of the tIPvXFltrEntryActAction object of this entry is 'forwardSap'. In addition a non-zero value can only be given if the object tIPvXFltrEntryActFwdSdpBind is '0'. Note that the value of tIPvXFltrEntryActFwdSapPortId is silently cleared by the system if tIPvXFltrEntryActAction is set to value other than 'forwardSap'.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActFwdSapEncapVal specifies the sap port encap value of the destination SAP for this filter entry. A value different from 0 can only be specified if the value of the tIPvXFltrEntryActAction object of this entry is 'forwardSap'. In addition a non-zero value can only be given if the object tIPvXFltrEntryActFwdSdpBind has value '0'. The value 0 indicates that either 1) the sap encapsulation value is not specified when tIPvXFltrEntryActFwdSapPortId and based on the filter type tIPFilterParamsFwdSvcId or tIPv6FilterParamsFwdSvcId have valid values; or 2) that there is no SAP destination. Note that the value of tIPvXFltrEntryActFwdSapEncapVal is silently cleared by the system if tIPvXFltrEntryActAction is set to value other than 'forwardSap'.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActFwdSdpBind specifies the sdp bind id of the destination for this filter entry. The value '0' indicates that there is currently no SDP binding defined. A value different from '0' can only be specified if the value of the tIPvXFltrEntryActAction object of this entry is 'forwardSdp'. In addition a non-zero value can only be given if the objects tIPvXFltrEntryActFwdSapPortId and tIPvXFltrEntryActFwdSapEncapVal have value 0. Note that the value of tIPvXFltrEntryActFwdSdpBind is silently cleared by the system if tIPvXFltrEntryActAction is set to value other than 'forwardSdp', or any object related to 'forward' other than this one is set.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActRedirectURL specifies the URL to redirect to, when the value of tIPvXFltrEntryActAction is 'httpRedirect'. The following macro substitutions are applicable in this context: $URL, $MAC, $IP, $SUB, $SAP, $SAPDESC, $CID, and $RID. Note that the value of tIPvXFltrEntryActRedirectURL is silently cleared by the system if tIPvXFltrEntryActAction is set to any value other than 'httpRedirect'.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActRdirAllwRadOvr specifies whether or not the value of tIPvXFltrEntryActRedirectURL can be overridden by a Radius VSA. The default value is false (i.e. the URL cannot be overridden by Radius). The value of tIPvXFltrEntryActRdirAllwRadOvr is relevant only if the value of tIPvXFltrEntryActAction is 'httpRedirect'. The value of tIPvXFltrEntryActRdirAllwRadOvr can't be set to true if the value of tIPvXFltrEntryActAction is not 'httpRedirect'. Furthermore, the value of tIPvXFltrEntryActRdirAllwRadOvr is silently reset to false by the system if tIPvXFltrEntryActAction is set to any value other than 'httpRedirect'.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActFwdRtrId specifies, if different from '0', the routing context in which the packet will be forwarded if it hits this filter entry. The action of this entry should be 'forwardRtr' or 'forwardNextHopRtr' in such a case. Note that the value of tIPvXFltrEntryActFwdRtrId is silently cleared by the system if tIPvXFltrEntryActAction is set to value other than 'forwardRtr' or 'forwardNextHopRtr'.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActNatPolicyName specifies the name of the NAT policy to be used when the value of tIPvXFltrEntryActAction is 'nat'. If the value is empty then a default policy is used. If the value is non-empty then it must correspond to a policy defined in tmnxNatPlcyTable. The value of tIPvXFltrEntryActNatPolicyName is relevant only if the value of tIPvXFltrEntryActAction is 'nat'. Setting the value of tIPvXFltrEntryActNatPolicyName to a non-empty string is allowed only if the value of tIPvXFltrEntryActAction is 'nat'. Furthermore, the value of tIPvXFltrEntryActNatPolicyName is silently reset to an empty string by the system if tIPvXFltrEntryActAction is set to any value other than 'nat'.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActNatType specifies the NAT type to be used when the value of tIPvXFltrEntryActAction is 'nat'. The object tIPvXFltrEntryActNatType is applicable only for IPv6 filters. The only supported value for ipv4 filters is value 'none'. Note that the value of tIPvXFltrEntryActNatType is silently cleared by the system if tIPvXFltrEntryActAction is set to value other than 'nat'.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActFwdLsp if different from '0' together with the value of the object tIPvXFltrEntryActFwdLspRtrId specifies the LSP into which a packet should be forwarded if it hits this filter entry. The value of the object tIPvXFltrEntryActAction of this entry must be 'forwardLsp' in such case. The value is reset to '0' if the value of the object tIPvXFltrEntryActAction is set to value other than 'forwardLsp'. The value has to be '0' if the value of the object tIPvXFltrEntryActFwdLspRtrId is not set (i.e. is '0'). If a non-zero value is set, the value of the object tIPvXFltrEntryActFwdLspRtrId has to be set as well.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActFwdLspRtrId specifies the router ID that the LSP ID defined by the value of the object tIPvXFltrEntryActFwdLsp belongs to. The value of the object tIPvXFltrEntryActAction of this entry must be 'forwardLsp' in such case. The value is reset to '0' if the value of the object tIPvXFltrEntryActAction is set to other value than 'forwardLsp'. The value has to be '0' if the value of the object tIPvXFltrEntryActFwdLsp is not set (i.e. is '0'). If a non-zero value is set, the value of the object tIPvXFltrEntryActFwdLsp has to be set as well. The ID of the base router and '0' are the only allowed values with this version of the product.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActPktLenVal1 specifies the value1 to be compared to the value of 'Total Length' field of IPv4 header or 'Payload Length' field of IPv6 header of an IP packet that has hit this filter's entry. The way how the value of this object is used depends on the value of the object tIPvXFltrEntryActPktLenOper. The value of this object can be set to a non-default value only if the value of the object tIPvXFltrEntryActPktLenOper is other than 'none (0)'. If the value of tIPvXFltrEntryActPktLenOper is 'range (2)' then the value of this object must be less than the value of tIPvXFltrEntryActPktLenVal2. If the value of tIPvXFltrEntryActPktLenOper is 'lt (3)' then the value of this object can be set in range 1..65535. If the value of tIPvXFltrEntryActPktLenOper is 'gt (4)' then the value of this object can be set in range 0..65534. If both the values of the objects tIPvXFltrEntryActPktLenOper and tIPvXFltrEntryActPktLenVal1 need to be changed then it must be done in the same SET SNMP request. Note that the value of this object is silently cleared by the system if tIPvXFltrEntryActAction is set to a value other than 'dropPktLen' or 'rateLimitPktLen'.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActPktLenVal2 specifies the value2 to be compared to the value of 'Total Length' field of IPv4 header or 'Payload Length' field of IPv6 header of an IP packet that has hit this filter's entry. The way how the value of this object is used depends on the value of the object tIPvXFltrEntryActPktLenOper. The value of this object can be set to a non-default value only if the value of the object tIPvXFltrEntryActPktLenOper is 'range (2)'. The value of this object must be greater than the value of tIPvXFltrEntryActPktLenVal1. If both the values of the objects tIPvXFltrEntryActPktLenOper and tIPvXFltrEntryActPktLenVal2 need to be changed then it must be done in the same SET SNMP request. Note that the value of this object is silently cleared by the system if tIPvXFltrEntryActAction is set to a value other than 'dropPktLen' or 'rateLimitPktLen'.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActPktLenOper specifies the way how the values of the objects tIPvXFltrEntryActPktLenVal1 and tIPvXFltrEntryActPktLenVal2 are used to form a condition that must be fulfilled in order to execute the action specified by the value of tIPvXFltrEntryActAction. Otherwise the opposite action is executed. The value of this object can be set to a non-default value only if the value of the object tIPvXFltrEntryActAction is 'dropPktLen' or 'rateLimitPktLen'. If the value of this object is being changed from the default value to any non-default value the value of the object tIPvXFltrEntryActAction must be sent in the same SET SNMP request. If the value of this object is 'eq (1)' then the value of the Total Length field of the IP header of the packet that has matched this filter's entry must be equal to the value of the object tIPvXFltrEntryActPktLenVal1 in order to execute the TRUE case action (see table below). Otherwise the FALSE case action is executed. The value of the object tIPvXFltrEntryActPktLenVal2 is ignored. If the value of this object is 'range (2)' then the value of the Total Length field of the IP header of the packet that has matched this filter's entry must be greater than or equal to the value of the object tIPvXFltrEntryActPktLenVal1 and less than or equal to the value of the object tIPvXFltrEntryActPktLenVal2 in order to execute the TRUE case action (see table below). Otherwise the FALSE case action is executed. If the value of this object is 'lt (3)' then the value of the Total Length field of the IP header of the packet that has matched this filter's entry must be less than the value of the object tIPvXFltrEntryActPktLenVal1 in order to execute the TRUE case action (see table below). Otherwise the FALSE case action is executed. The value of the object tIPvXFltrEntryActPktLenVal2 is ignored. If the value of this object is 'gt (4)' then the value of the Total Length field of the IP header of the packet that has matched this filter's entry must be greater than the value of the object tIPvXFltrEntryActPktLenVal1 in order to execute the TRUE case action (see table below). Otherwise the FALSE case action is executed. The value of the object tIPvXFltrEntryActPktLenVal2 is ignored. tIPvXFltrEntryActAction | TRUE case action | FALSE case action ------------------------------------------------------------------ dropPktLen | drop | forward ------------------------------------------------------------------ rateLimitPktLen | rateLimit | forward Allowed ranges for the values of tIPvXFltrEntryActPktLenVal1 and tIPvXFltrEntryActPktLenVal2 are: Operator |Packet Length Value 1|Packet Length Value 2 -------------------------------------------------------------------- none (0) | N/A | N/A eq(1) | 0..65535 | N/A range(2) | 0..65534 | (Value1 + 1)..65535 lt(3) | 1..65535 | N/A gt(4) | 0..65534 | N/A Note that the value of this object is silently cleared by the system if tIPvXFltrEntryActAction is set to a value other than 'dropPktLen' or 'rateLimitPktLen'.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActTTLVal1 specifies the value1 to be compared to the value of 'Time-to-live' field of IPv4 header or 'Hop-Limit' field of IPv6 header of an IP packet that has hit this filter's entry. The way how the value of this object is used depends on the value of the object tIPvXFltrEntryActTTLOper. The value of this object can be set to a non-default value only if the value of the object tIPvXFltrEntryActTTLOper is other than 'none (0)'. If the value of tIPvXFltrEntryActTTLOper is 'range (2)' then the value of this object must be less than the value of tIPvXFltrEntryActTTLVal2. If the value of tIPvXFltrEntryActTTLOper is 'lt (3)' then the value of this object can be set in range 1..255. If the value of tIPvXFltrEntryActTTLOper is 'gt (4)' then the value of this object can be set in range 0..254. If both the values of the objects tIPvXFltrEntryActTTLOper and tIPvXFltrEntryActTTLVal1 need to be changed then it must be done in the same SET SNMP request. Note that the value of this object is silently cleared by the system if tIPvXFltrEntryActAction is set to a value other than 'dropTtl' or 'rateLimitTtl'.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActTTLVal2 specifies value2 to be compared to the value of 'Time-to-live' field of IPv4 header or 'Hop-Limit' field of IPv6 header of an IP packet that has hit this filter's entry. The way how the value of this object is used depends on the value of the object tIPvXFltrEntryActTTLOper. The value of this object can be set to a non-default value only if the value of the object tIPvXFltrEntryActTTLOper is 'range (2)'. The value of this object must be greater than the value of tIPvXFltrEntryActTTLVal1. If both the values of the objects tIPvXFltrEntryActTTLOper and tIPvXFltrEntryActTTLVal2 need to be changed then it must be done in the same SET SNMP request. Note that the value of this object is silently cleared by the system if tIPvXFltrEntryActAction is set to a value other than 'dropTtl' or 'rateLimitTtl'.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActTTLOper specifies the way how the values of the objects tIPvXFltrEntryActTTLVal1 and tIPvXFltrEntryActTTLVal2 are used to form a condition that must be fulfilled in order to execute the action specified by the value of tIPvXFltrEntryActAction. Otherwise the opposite action is executed. The value of this object can be set to a non-default value only if the value of the object tIPvXFltrEntryActAction is 'dropTtl' or 'rateLimitTtl'. If the value of this object is being changed from the default value to any non-default value the value of the object tIPvXFltrEntryActAction must be sent in the same SET SNMP request. If the value of this object is 'eq (1)' then the value of the Time-To-Live field of the IP header of the packet that has matched this filter's entry must be equal to the value of the object tIPvXFltrEntryActTTLVal1 in order to execute the TRUE case action (see table below). Otherwise the FALSE case action is executed. The value of the object tIPvXFltrEntryActTTLVal2 is ignored. If the value of this object is 'range (2)' then the value of the Time-To-Live field of the IP header of the packet that has matched this filter's entry must be greater than or equal to the value of the object tIPvXFltrEntryActTTLVal1 and less than or equal to the value of the object tIPvXFltrEntryActTTLVal2 in order to execute the TRUE case action (see table below). Otherwise the FALSE case action is executed. If the value of this object is 'lt (3)' then the value of the Time-To-Live field of the IP header of the packet that has matched this filter's entry must be less than the value of the object tIPvXFltrEntryActTTLVal1 in order to execute the TRUE case action (see table below). Otherwise the FALSE case action is executed. The value of the object tIPvXFltrEntryActTTLVal2 is ignored. If the value of this object is 'gt (4)' then the value of the Time-To-Live field of the IP header of the packet that has matched this filter's entry must be greater than the value of the object tIPvXFltrEntryActTTLVal1 in order to execute the TRUE case action (see table below). Otherwise the FALSE case action is executed. The value of the object tIPvXFltrEntryActTTLVal2 is ignored. tIPvXFltrEntryActAction | TRUE case action | FALSE case action ------------------------------------------------------------------ dropTtl | drop | forward ------------------------------------------------------------------ rateLimitTtl | rateLimit | forward Allowed ranges for the values of tIPvXFltrEntryActTTLVal1 and tIPvXFltrEntryActTTLVal2 are: Operator | Time-To-Live Value 1| Time-To-Live Value 2 -------------------------------------------------------------------- none (0) | N/A | N/A eq(1) | 0..255 | N/A range(2) | 0..254 | (Value1 + 1)..255 lt(3) | 1..255 | N/A gt(4) | 0..254 | N/A Note that the value of this object is silently cleared by the system if tIPvXFltrEntryActAction is set to a value other than 'dropTtl' or 'rateLimitTtl'.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActEsi specifies the ethernet segment identifier (ESI) of the first ESI identified appliance in Nuage service chain. When the value of tMacFilterParamsAction is 'forwardEsiL2' or 'forwardEsiL3' packets matching the filter entry are forwarded to the appliance using EVPN-resolved VXLAN tunnel in the specified VPLS/VPRN service (tIPvXFltrEntryActFwdEsiSvcId/tIPvXFltrEntryActFwdEsiVRtrId). The value '0' indicates that there is no ESI specified. There are two options how to set the value of tIPvXFltrEntryActEsi: 1. Non zero value of tIPvXFltrEntryActEsi is set together with non zero values of tIPvXFltrEntryActFwdEsiVRtrId, tIPvXFltrEntryActFwdEsiSFIpType and tIPvXFltrEntryActFwdEsiSFIp. In this case value of tIPvXFltrEntryActAction is set to 'forwardEsiL3' by the system. 2. Non zero value of tIPvXFltrEntryActEsi is set together with a non zero value of tIPvXFltrEntryActFwdEsiSvcId. In this case value of tIPvXFltrEntryActAction is set to 'forwardEsiL2' by the system. Note that the value of tIPvXFltrEntryActEsi is silently cleared by the system if the value of tIPvXFltrEntryActAction is set to any value other than 'forwardEsiL2' or 'forwardEsiL3'.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActFwdEsiSvcId specifies the identifier of a VPLS used for VPN/DC connectivity. The value '0' indicates that there is no VPLS identifier specified. The non zero value of tIPvXFltrEntryActFwdEsiSvcId must be set together with a non zero value of tIPvXFltrEntryActEsi. Note that the value of tIPvXFltrEntryActFwdEsiSvcId is silently cleared by the system if the value of tIPvXFltrEntryActAction is set to any value other than 'forwardEsiL2'.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActFwdEsiVRtrId specifies the VPRN/rVPLS virtual router identifier used for VPN/DC connectivity. The value '0' indicates that there is no VPRN/rVPLS virtual router identifier specified. The non zero value of tIPvXFltrEntryActFwdEsiVRtrId must be set together with non zero values of tIPvXFltrEntryActEsi, tIPvXFltrEntryActFwdEsiSFIpType and tIPvXFltrEntryActFwdEsiSFIp. Note that the value of tIPvXFltrEntryActFwdEsiVRtrId is silently cleared by the system if the value of tIPvXFltrEntryActAction is set to any value other than 'forwardEsiL3'.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActFwdEsiSFIpType specifies the context in which the value of tIPvXFltrEntryActFwdEsiSFIp is interpreted. Only following values are supported: unknown(0) ipv4(1) ipv6(2) The value 'unknown' indicates that service function IP address type is not specified. If the value is different from 'unknown' it must be consistent with filter type given by the value of the object tIPvXFltrEntryActFltrType. The non zero value of tIPvXFltrEntryActFwdEsiSFIpType must be set together with a non zero values of tIPvXFltrEntryActFwdEsiSFIp, tIPvXFltrEntryActFwdEsiVRtrId and tIPvXFltrEntryActEsi. Note that the value of tIPvXFltrEntryActFwdEsiSFIpType is silently cleared by the system if the value of tIPvXFltrEntryActAction is set to any value other than 'forwardEsiL3'.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActFwdEsiSFIp specifies the IP address of the service function toward which traffic is steered. The value '0' indicates that no service function IP address is specified. The non zero value of tIPvXFltrEntryActFwdEsiSFIp must be set together with a non zero values of tIPvXFltrEntryActFwdEsiSFIpType, tIPvXFltrEntryActFwdEsiVRtrId and tIPvXFltrEntryActEsi. Note that the value of tIPvXFltrEntryActFwdEsiSFIp is silently cleared by the system if the value of tIPvXFltrEntryActAction is set to any value other than 'forwardEsiL3'.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActFwdEsiVasIf specifies the virtual router interface index of VPRN RVPLS interface used for VPN/DC connectivity. The value '0' indicates that no interface id is specified. The non zero value of tIPvXFltrEntryActFwdEsiVasIf must be set together with a non zero values of tIPvXFltrEntryActFwdEsiVRtrId, tIPvXFltrEntryActFwdEsiSFIp, tIPvXFltrEntryActFwdEsiSFIpType and tIPvXFltrEntryActEsi. Note: The value of tIPvXFltrEntryActFwdEsiVasIf is set to '0' by the system if the value of tIPvXFltrEntryActAction is set to any value other than 'forwardEsiL3'.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActRateLimit specifies the rate to which the traffic matching the filter entry will be limited. The value of tIPvXFltrEntryActRateLimit can be set to non default value only if the value of tIPvXFltrEntryActAction is set to 'rateLimit'. Note that the value of tIPvXFltrEntryActRateLimit is silently cleared by the system if the value of tIPvXFltrEntryActAction is set to any value other than 'rateLimit'.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActPbrTargetStatus indicates the PBR target status. Refer to the description of the textual convention TFilterPbrTargetStatus for more information.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActRemarkDSCP specifies the value which remarks the DSCP value of packet matching the filter entry. The value of tIPvXFltrEntryActRemarkDSCP can be set to non default value only if the value of tIPvXFltrEntryActAction is set to 'remarkDscp' or the value of tIPvXFltrEntryActActionExt is set to 'remarkDscp' and the value of tIPvXFltrEntryActAction is set to one of the following values: forwardEsiL3 forwardRtr forwardNextHop forwardNextHopRtr forwardNHInterface forwardLsp forwardRPlcy Note that the value of tIPvXFltrEntryActRemarkDSCP is silently cleared by the system if the value of tIPvXFltrEntryActAction is changed from 'remarkDscp' to any other value or if tIPvXFltrEntryActActionExt is changed from 'remarkDscp' to any other value.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActActionExt specifies the action to be taken on a packet along with action specified by tIPvXFltrEntryActAction. Refer to the description of the textual convention TIPvXFilterEntryActionExt for more information.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActFwdVprnTgtBgNHT specifies the context in which the value of tIPvXFltrEntryActFwdVprnTgtBgNH is interpreted. Only following values are supported: unknown(0) ipv4(1) The value 'unknown' indicates IP address type is not specified. The non zero value of tIPvXFltrEntryActFwdVprnTgtBgNHT must be set together with non zero values of tIPvXFltrEntryActFwdVprnTgtBgNH, tIPvXFltrEntryActFwdVprnTgtRtrId and tIPvXFltrEntryActAction value 'forwardVprnTarget'. Note that the value of tIPvXFltrEntryActFwdVprnTgtBgNHT is silently cleared by the system if the value of tIPvXFltrEntryActAction is set to any value other than 'forwardVprnTarget'.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActFwdVprnTgtBgNH specifies the target BGP next-hop IP address. The value '0' indicates that no IP address is specified. The non zero value of tIPvXFltrEntryActFwdVprnTgtBgNH must be set together with non zero values of tIPvXFltrEntryActFwdVprnTgtBgNHT, tIPvXFltrEntryActFwdVprnTgtRtrId and tIPvXFltrEntryActAction value 'forwardVprnTarget'. Note that the value of tIPvXFltrEntryActFwdVprnTgtBgNH is silently cleared by the system if the value of tIPvXFltrEntryActAction is set to any value other than 'forwardVprnTarget'.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActFwdVprnTgtRtrId specifies the virtual router used for route lookup. The value '0' indicates that no virtual router is specified. The non zero value of tIPvXFltrEntryActFwdVprnTgtRtrId must be set together with non zero values of tIPvXFltrEntryActFwdVprnTgtBgNHT, tIPvXFltrEntryActFwdVprnTgtBgNH and tIPvXFltrEntryActAction value 'forwardVprnTarget'. Note that the value of tIPvXFltrEntryActFwdVprnTgtRtrId is silently cleared by the system if the value of tIPvXFltrEntryActAction is set to any value other than 'forwardVprnTarget'.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActFwdVprnTgtAdPxT specifies the context in which the value of tIPvXFltrEntryActFwdVprnTgtAdPx is interpreted. Only following values are supported: unknown(0) ipv4(1) ipv6(2) The value 'unknown' indicates that IP address type is not specified. If the value is different from 'unknown' it must be consistent with filter type given by the value of the object tIPvXFltrEntryActFltrType. The non zero value of tIPvXFltrEntryActFwdVprnTgtAdPxT must be set together with a non zero value of tIPvXFltrEntryActFwdVprnTgtAdPx. In such case the values of tIPvXFltrEntryActFwdVprnTgtBgNHT, tIPvXFltrEntryActFwdVprnTgtBgNH and tIPvXFltrEntryActFwdVprnTgtRtrId must have non default value and the value of tIPvXFltrEntryActAction must be 'forwardVprnTarget'. Note that the value of tIPvXFltrEntryActFwdVprnTgtAdPxT is silently cleared by the system if the value of tIPvXFltrEntryActAction is set to any value other than 'forwardVprnTarget'.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActFwdVprnTgtAdPx specifies the IP address of the service function toward which traffic is steered. The value '0' indicates that no prefix is specified. The non zero value of tIPvXFltrEntryActFwdVprnTgtAdPx must be set together with non zero value of tIPvXFltrEntryActFwdVprnTgtAdPxT. In such case the values of tIPvXFltrEntryActFwdVprnTgtBgNHT, tIPvXFltrEntryActFwdVprnTgtBgNH and tIPvXFltrEntryActFwdVprnTgtRtrId must have non default values and the value of tIPvXFltrEntryActAction must be 'forwardVprnTarget'. Note that the value of tIPvXFltrEntryActFwdVprnTgtAdPx is silently cleared by the system if the value of tIPvXFltrEntryActAction is set to any value other than 'forwardVprnTarget'.

OBJECT-TYPE

The value of tIPvXFltrEntryActFwdVprnTgtAdPxL specifies the IP prefix length of this prefix list entry.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActFwdVprnTgtLspId specifies LSP used for forwarding the packet. The value '0' indicates that no prefix is specified. The non zero value of tIPvXFltrEntryActFwdVprnTgtLspId can be set only when values of tIPvXFltrEntryActFwdVprnTgtBgNHT, tIPvXFltrEntryActFwdVprnTgtBgNH and tIPvXFltrEntryActFwdVprnTgtRtrId have non default values and the value of tIPvXFltrEntryActAction is 'forwardVprnTarget'. Note that the value of tIPvXFltrEntryActFwdVprnTgtAdPx is silently cleared by the system if the value of tIPvXFltrEntryActAction is set to any value other than 'forwardVprnTarget'.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActFwdBondingConn specifies the bonding connection ID.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActFcName specifies the forwarding class name.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActFwdGreTun specifies the GRE tunnel template to be used. The action of this entry should be 'forwardGreTunnel' in such a case. Note that the value of tIPvXFltrEntryActFwdGreTun is silently cleared by the system if tIPvXFltrEntryActAction is set to value other than 'forwardGreTunnel'.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActCondExpression specifies the expression to be matched. tIPvXFltrEntryActCondExpression has to be set together with tIPvXFltrEntryActCondExpMask, tIPvXFltrEntryActCondOffsetType, tIPvXFltrEntryActCondOffsetVal and tIPvXFltrEntryActAction. The value of tIPvXFltrEntryActAction has to be set to one of the following values: 'dropPattern', 'rateLimitPattern', 'forwardPattern'. Note that the value of tIPvXFltrEntryActCondExpression is silently cleared by the system if the value of tIPvXFltrEntryActAction is set to any value other than 'dropPattern', 'rateLimitPattern', 'forwardPattern'.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActCondExpMask specifies the expression mask. tIPvXFltrEntryActCondExpMask has to be set together with tIPvXFltrEntryActCondExpression, tIPvXFltrEntryActCondOffsetType, tIPvXFltrEntryActCondOffsetVal and tIPvXFltrEntryActAction. The value of tIPvXFltrEntryActAction has to be set to one of the following values: 'dropPattern', 'rateLimitPattern', 'forwardPattern'. Note that the value of tIPvXFltrEntryActCondExpMask is silently cleared by the system if the value of tIPvXFltrEntryActAction is set to any value other than 'dropPattern', 'rateLimitPattern', 'forwardPattern'.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActCondOffsetType specifies the offset type of the expression. tIPvXFltrEntryActCondOffsetType has to be set together with tIPvXFltrEntryActCondExpression, tIPvXFltrEntryActCondExpMask, tIPvXFltrEntryActCondOffsetVal and tIPvXFltrEntryActAction. The value of tIPvXFltrEntryActAction has to be set to one of the following values: 'dropPattern', 'rateLimitPattern', 'forwardPattern'. Note that the value of tIPvXFltrEntryActCondOffsetType is silently cleared by the system if the value of tIPvXFltrEntryActAction is set to any value other than 'dropPattern', 'rateLimitPattern', 'forwardPattern'.

OBJECT-TYPE

The value of the object tIPvXFltrEntryActCondOffsetVal specifies the offset of the expression. -1 indicates offset is not set. tIPvXFltrEntryActCondOffsetVal has to be set together with tIPvXFltrEntryActCondExpression, tIPvXFltrEntryActCondOffsetType, tIPvXFltrEntryActCondExpMask and tIPvXFltrEntryActAction. The value of tIPvXFltrEntryActAction has to be set to one of the following values: 'dropPattern', 'rateLimitPattern', 'forwardPattern'. Note that the value of tIPvXFltrEntryActCondOffsetVal is silently cleared by the system if the value of tIPvXFltrEntryActAction is set to any value other than 'dropPattern', 'rateLimitPattern', 'forwardPattern'.

OBJECT-TYPE

The name of the MPLS forwarding policy endpoint to be used when the value of tIPvXFltrEntryActAction is 'forwardMplsPlcyEndpt' Only following values are supported: unknown(0) ipv4(1) ipv6(2) The value 'unknown' indicates IP address type is not specified. The non zero value of tIPvXFltrFwdMplsPlcyEndptAddrTp must be set together with non zero values of tIPvXFltrFwdMplsPlcyEndptAddr, and tIPvXFltrEntryActAction value 'forwardMplsPlcyEndpt'. Note that the value of tIPvXFltrFwdMplsPlcyEndptAddrTp is silently cleared by the system if the value of tIPvXFltrEntryActAction is set to any value other than 'forwardMplsPlcyEndpt'.

OBJECT-TYPE

The value specifies the MPLS forwarding policy endpoint address to be used when the value of tIPvXFltrEntryActAction is 'forwardMplsPlcyEndpt'. The value '0' indicates that no IP address is specified. The non zero value of tIPvXFltrFwdMplsPlcyEndptAddr must be set together with non zero values of tIPvXFltrFwdMplsPlcyEndptAddrTp, and tIPvXFltrEntryActAction value 'forwardMplsPlcyEndpt'. Note that the value of tIPvXFltrFwdMplsPlcyEndptAddr is silently cleared by the system if the value of tIPvXFltrEntryActAction is set to any value other than 'forwardMplsPlcyEndpt'.

OBJECT-TYPE

The name of the SR-TE policy endpoint to be used when the value of tIPvXFltrEntryActAction is 'forwardSrtePlcyEndptColor' Only following values are supported: unknown(0) ipv4(1) ipv6(2) The value 'unknown' indicates IP address type is not specified. The non zero value of tIPvXFltrFwdSrtePlcyEndptAddrTp must be set together with non zero values of tIPvXFltrFwdSrtePlcyEndptAddr, and tIPvXFltrEntryActAction value 'forwardSrtePlcyEndptColor'. Note that the value of tIPvXFltrFwdSrtePlcyEndptAddrTp is silently cleared by the system if the value of tIPvXFltrEntryActAction is set to any value other than 'forwardSrtePlcyEndptColor'.

OBJECT-TYPE

The value specifies the SR-TE policy endpoint address to be used when the value of tIPvXFltrEntryActAction is 'forwardSrtePlcyEndptColor'. The value '0' indicates that no IP address is specified. The non zero value of tIPvXFltrFwdSrtePlcyEndptAddr must be set together with non zero values of tIPvXFltrFwdSrtePlcyEndptAddrTp, and tIPvXFltrEntryActAction value 'forwardSrtePlcyEndptColor'. Note that the value of tIPvXFltrFwdSrtePlcyEndptAddr is silently cleared by the system if the value of tIPvXFltrEntryActAction is set to any value other than 'forwardSrtePlcyEndptColor'.

OBJECT-TYPE

The value of the SR-TE policy color to be used when the value of tIPvXFltrEntryActAction is 'forwardSrtePlcyEndptColor'.

OBJECT-TYPE

The table tFltrEntryStatTable contains statistics and counters pertaining to IPv4, IPv6 and MAC ACL filter entries.

OBJECT-TYPE

The entry contains statistics pertaining to a particular IPv4, IPv6 or MAC ACL filter entry. Entries in this table are created by the system.

OBJECT-TYPE

The value of the object tFltrEntryStatFltrType specifies the type of ACL filter. Refer to the description of the textual convention TFilterType for more information.

OBJECT-TYPE

The value of the object tFltrEntryStatFltrId specifies the filter id of an IP, IPv6 or MAC ACL filter based on the value of tFltrEntryStatFltrType. Refer to the description of the textual convention TAnyFilterID for more information.

OBJECT-TYPE

The value of the object tFltrEntryStatFltrEntryId specifies the entry id of filter of type IP, IPv6 or MAC based on the value of tFltrEntryStatFltrType.

OBJECT-TYPE

The value of the object tFltrEntryStatIngHitCnt indicates the number of times an ingress packet matched the filter entry.

OBJECT-TYPE

The value of tFltrEntryStatIngHitCntB indicates the number of bytes of all ingress packets that matched this entry.

OBJECT-TYPE

The value of the object tFltrEntryStatEgrHitCnt indicates the number of times an egress packet matched the filter entry.

OBJECT-TYPE

The value of tFltrEntryStatEgrHitCntB indicates the number of bytes of all egress packets that matched this entry.

OBJECT-TYPE

The value of the object tFltrEntryStatRateLmtIngHitCnt indicates how many ingress packets were subjected to rate-limiting filter action.

OBJECT-TYPE

The value of the object tFltrEntryStatRateLmtIngHitCntB indicates the number of bytes of all ingress packets that were subjected to rate-limiting filter action.

OBJECT-TYPE

The value of the object tFltrEntryStatRateLmtIngDrop indicates how many ingress packets which were subjected to rate-limiting filter action were dropped.

OBJECT-TYPE

The value of the object tFltrEntryStatRateLmtIngDropB indicates the number of bytes of all ingress packets which were subjected to rate-limiting filter action were dropped.

OBJECT-TYPE

The value of the object tFltrEntryStatRateLmtIngFwd indicates how many ingress packets which were subjected to rate-limiting filter action were forwarded.

OBJECT-TYPE

The value of the object tFltrEntryStatRateLmtIngFwdB indicates the number of bytes of all ingress packets which were subjected to rate-limiting filter action were forwarded.

OBJECT-TYPE

The value of the object tFltrEntryStatRateLmtEgrHitCnt indicates how many egress packets were subjected to rate-limiting filter action.

OBJECT-TYPE

The value of the object tFltrEntryStatRateLmtEgrHitCntB indicates the number of bytes of all egress packets that were subjected to rate-limiting filter action.

OBJECT-TYPE

The value of the object tFltrEntryStatRateLmtEgrDrop indicates how many egress packets which were subjected to rate-limiting filter action were dropped.

OBJECT-TYPE

The value of the object tFltrEntryStatRateLmtEgrDropB indicates the number of bytes of all egress packets which were subjected to rate-limiting filter action were dropped.