TIMETRA-LDP-MIB

TEXTUAL-CONVENTION

TmnxLabelSigStatus specifies the status of the pseudowire and attached circuit. The values are defined in draft-ietf-pwe3-iana-allocation-07.txt.

TEXTUAL-CONVENTION

TmnxLabelStatus bit flags specifies the status of an ingress or egress label. Flags marked dummy* are not used and MUST be 0. 'statusSignalingSupported' - indicates whether status signaling is enabled or not. 'inUsePush' - indicates that the label contains valid information that is currently being used as a 'push' label. 'inUseSwap' - indicates that the label contains valid information that is currently being used as a 'swap' label. 'inUsePop' - indicates that the label contains valid information that is currently being used as a 'pop' label. 'released' - indicates that the label is in the process of being freed. With this flag set, no other flags will be set. 'notInUse' - indicates that the label contains valid information but is currently not being used possibly because the service is temporarily down. 'withdrawn' - indicates that the label has not been sent (possibly due to a mismatch in control word or status signaling) 'controlWord' - indicates that the control word will be signaled 'withdrawPending' - indicates that the label withdrawal is pending 'alternateNextHop' - indicates that the label is programmed as alternate next-hop for fast reroute 'alternatePHop' - indicates that the label is programmed as alternate upstream for fast reroute. 'unnumIf' - indicates that the label is programmed using unnumbered interface. 'srIsisNextHop' - LDP binding is resolved to ISIS segment routing next-hop. 'srOspfNextHop' - LDP binding is resolved to OSPF segment routing next-hop. 'entLblCap' - entropy label capabilities. }

TEXTUAL-CONVENTION

TmnxLdpAdjacencyType describes the type of adjacency, either targeted or link, for a row in the vRtrLdpHelloAdjTable. It also describes the type of adjacencies in an LDP Session row in the vRtrLdpSessionTable.

TEXTUAL-CONVENTION

TmnxLdpBackoffTime specifies the backoff interval (initial and maximum). The backoff interval is the time, in seconds, that LDP waits after an LDP session setup has failed before it attempts to setup the session again. After the LDP session startup fails the first time, the backoff interval is set to an initial value. Thereafter, if session startup fails again the backoff interval increases exponentially until it reaches a maximum value specified by the maximum backoff interval. If the maximum backoff interval is set to zero (0), then the backoff interval does not increase exponentially after the first session startup attempt fails. Instead it remains constant and LDP will keep retrying to establish a session until it succeeds.

TEXTUAL-CONVENTION

TmnxLdpFECFlags bit flags define the characteristics of FEC. Flags marked dummy* are not used and MUST be 0. Flag 'egress': this node is an egress for this FEC. Flag 'ingress': this node is a potential ingress for this FEC. Flag 'installedSwap': the label for this FEC has been programmed as a 'swap' label. Flag 'installedPush': the label for this FEC has been programmed as a 'push' label. Flag 'installedPop': the label for this FEC has been programmed as a 'pop' label. Flag 'local': this FEC is local to this node. Flag 'nextHop': the nextHop for this FEC is known. Flag 'importPolicyRejected': global LDP import policy has rejected this FEC. Flag 'exportPolicyAccepted': global LDP export policy has accepted this FEC. Flag 'installedStaticFec': this FEC is created by static FEC configuration on this node. Flag 'vcSwitching': vcSwitching is enabled for the FEC. Flag 'importTargPolicyRejected': targeted LDP import policy has rejected this FEC. Flag 'exportTargPolicyRejected': targeted LDP export policy has rejected this FEC. Flag 'importPeerPolicyRejected': peer LDP import policy has rejected this FEC. Flag 'localMultihomedSecondary': this FEC is local to this node and is a multi-homed secondary ip address. Flag 'bgpNextHop' : LDP binding is resolved to BGP next-hop. Flag 'labelReqSent' : Label request to peer has been sent. Flag 'classBasedForwarding' : Label binding is using class-based-forwarding. Flag 'srIsisNextHop' : LDP binding is resolved to ISIS segment routing next-hop. Flag 'srOspfNextHop' : LDP binding is resolved to OSPF segment routing next-hop. Flag 'upperFec' : this upper FEC is stitched to lower FEC Flag 'lowerFec' : this lower FEC is stitched to upper FEC Flag 'communityMismatch' : targeted LDP community mismatch Flag 'bkpUpperFec' : backup upper FEC

TEXTUAL-CONVENTION

TmnxLdpFECPolicy determines whether the LSR should generate FECs and which FECs it should generate. system(1) - LDP will distribute label bindings only for the router's system IP address interface(2) - LDP will distribute label bindings for all LDP interfaces all(3) - LDP will distribute label bindings for all prefixes in the routing table none(4) - LDP will not distribute any label bindings.

TEXTUAL-CONVENTION

TmnxLdpFECTunnelType determines the type of tunnel that the label mapping messages are referring to.

TEXTUAL-CONVENTION

TmnxLdpFec129Tlv is a Type-Length-Value (Tlv) that specifies the value encoded as one byte Type followed by one byte Length followed by the 'Length' size Value used for FEC-129 attribute.

TEXTUAL-CONVENTION

TmnxLdpGenOperDownReasonCode is an enumerated integer that specifies the reason that the LDP instance is operationally down.

TEXTUAL-CONVENTION

TmnxLdpHelloFactor specifies the value by which the hello timeout should be divided to give the hello time i.e. the time interval, in seconds, between LDP Hello messages. LDP uses Hello messages to discover neighbors and to detect loss of connectivity with its neighbors.

TEXTUAL-CONVENTION

TmnxLdpHelloTimeout specifies the the time interval, in seconds, that LDP waits before declaring a neighbor to be down. Hello timeout is local to the system and is sent in the Hello messages to a neighbor. Hello timeout cannot be set to a value that is less than 3 times the hello time.

TEXTUAL-CONVENTION

TmnxLdpInLblWdrawalReasonCode is an enumerated integer that specifies the reason that the LDP ingress label is withdrawn. The value of 'none(0)' means no reason specified for the withdrawal of the ingress label. The value of 'noSwLabel(1)' means the ingress label is withdrawn because there is no vc switching label from upstream. The value of 'localFault(2)' means the ingress label is withdrawn because there is a local fault. The value of 'stackMismatch(3)' means the ingress label is withdrawn due to stack capability mismatch.

TEXTUAL-CONVENTION

TmnxLdpIntTargOperDownReasonCode is an enumerated integer that specifies the reason that the LDP interface and targeted peer is operationally down.

TEXTUAL-CONVENTION

TmnxLdpKeepAliveFactor specifies the value by which the keepalive timeout should be divided to give the keepalive time i.e. the time interval, in seconds, between LDP Keepalive messages. LDP Keepalive messages are sent to keep the LDP session from timing out when no other LDP traffic is being sent between the neighbors.

TEXTUAL-CONVENTION

TmnxLdpKeepAliveTimeout specifies the the time interval, in seconds, that LDP waits before tearing down a session. If no LDP messages are exchanged during this time interval, the LDP session is torn down. Generally the keepalive timeout interval should be configured to be 3 times the keepalive time (the time interval between successive LDP Keepalive messages).

TEXTUAL-CONVENTION

TmnxLdpLabelDistMethod describes the label distribution method used. When the value is 'downstreamOnDemand', label bindings are distributed to the upstream LSR only when a label request message is received. When the value is 'downstreamUnsolicited', label bindings are distributed to the upstream LSR, for each FEC, without requiring a request message for the FEC from the upstream LSR.

TEXTUAL-CONVENTION

TmnxLdpNewHelloTimeout specifies the the time interval, in seconds, that LDP waits before declaring a neighbor to be down. Hello timeout is local to the system and is sent in the Hello messages to a neighbor. Hello timeout cannot be set to a value that is less than 3 times the hello time. The minimum value TmnxLdpHelloTimeout can have is 1 whereas the minimum value TmnxLdpNewHelloTimeout can have is 3. This new textual convention prevents setting value for timeouts to be less than 3 seconds.

TEXTUAL-CONVENTION

TmnxLdpNewKeepAliveTimeout specifies the the time interval, in seconds, that LDP waits before tearing down a session. If no LDP messages are exchanged during this time interval, the LDP session is torn down. Generally the keepalive timeout interval should be configured to be 3 times the keepalive time (the time interval between successive LDP Keepalive messages). The minimum value TmnxLdpKeepAliveTimeout can have is 1 whereas the minimum value TmnxLdpNewKeepAliveTimeout can have is 3. This new textual convention prevents setting value for timeouts to be less than 3 seconds.

TEXTUAL-CONVENTION

TmnxVpnId specifies the value of a VPN (Virtual Private Network) identifier. This is a 10 byte value - the VPN 'type' is stored in the first two bytes the TmnxVpnId. The next four bytes store an 'AS (Autonomous System) number'. A 'local identifier' for the VPN is stored as the last four bytes.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

vRtrLdpGeneralTable has an entry for each virtual router in the system capable of supporting an instance of the Label Distribution Protocol (LDP). In 13.0 this table has been replaced by TIMETRA-LDP-NG-MIB::vRtrLdpNgGeneralTable, TIMETRA-LDP-NG-MIB::vRtrLdpNgCapabilityTable, TIMETRA-LDP-NG-MIB::vRtrLdpNgPolicyTable.

OBJECT-TYPE

Each row entry represents an instance of the Label Distribution Protocol (LDP) for a virtual router in the system. An entry in this table is created by the agent when vRtrLdpStatus in the vRtrConfTable is set to 'create'. The entry is destroyed when vRtrLdpStatus is set to 'delete' but only if vRtrLdpGenAdminState has a value of 'outOfService'.

OBJECT-TYPE

The value of vRtrLdpGenLastChange specifies the sysUpTime when this row was last modified. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenAdminState specifies the desired administrative state for this LDP instance. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenOperState specifies the current operational state of this LDP instance. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenLdpLsrId is the Label Switch Router (LSR) identifier which is used as the first 4 bytes or the Router Id component of the Label Distribution Protocol (LDP) identifier. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenProtocolVersion specifies the version of the LDP protocol instance. A value of zero (0) indicates that the version of the protocol is unknown. This object was obsoleted in release 13.0.

OBJECT-TYPE

When vRtrLdpGenDeaggregateFec has a value of 'false', LDP aggregates multiple prefixes into a single Forwarding Equivalence Class (FEC) and advertises a single label for the FEC. When the value is 'true', LDP deaggregates prefixes into multiple FECs. This value is only applicable to LDP interfaces and not for targeted sessions. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenKeepAliveFactor specifies the value by which the keepalive timeout (vRtrLdpGenKeepAliveTimeout) should be divided to give the keepalive time i.e. the time interval, in seconds, between LDP keepalive messages. LDP keepalive messages are sent to keep the LDP session from timing out when no other LDP traffic is being sent between the neighbors. This value is only applicable to LDP interfaces and not for targeted sessions. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenKeepAliveTimeout specifies the time interval, in seconds, that LDP waits before tearing down a session. If no LDP messages are exchanged during this time interval, the LDP session is torn down. Generally the value of vRtrLdpGenKeepAliveTimeout is configured to be 3 times the keepalive time (the time interval between successive LDP keepalive messages). This value is only applicable to LDP interfaces and not for targeted sessions. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenHelloFactor specifies the value by which the hello timeout (vRtrLdpGenHelloTimeout) should be divided to give the hello time i.e. the time interval, in seconds, between LDP Hello messages. LDP uses hello messages to discover neighbors and to detect loss of connectivity with its neighbors. This value is only applicable to LDP interfaces and not for targeted sessions. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenHelloTimeout specifies the hello time also known as hold time. It is the time interval, in seconds, that LDP waits before declaring a neighbor to be down. Hello timeout is local to the system and is sent in the hello messages to a neighbor. Hello timeout cannot be set to a value that is less than 3 times the hello time. This value is only applicable to LDP interfaces and not for targeted sessions. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenRoutePreference specifies the route preference assigned to LDP routes. When multiple routes are available to a destination, the route with the lowest preference will be used. This value is only applicable to LDP interfaces and not for targeted sessions. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenControlMode specifies the mode used for distributing labels in response to label binding requests. When vRtrLdpGenControlMode has a value of 'ordered', label bindings are not distributed in response to a label request until a label binding has been received from the next hop for the destination. When vRtrLdpGenControlMode has a value of 'independent', label bindings are distributed immediately in response to a label request even if a label binding has not yet been received from the next hop for the destination. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenDistMethod specifies the label distribution method used. When vRtrLdpGenDistMethod has a value of 'downstreamOnDemand', label bindings are distributed to the upstream LSR, for each FEC, without requiring a request message for the FEC from the upstream LSR. When vRtrLdpGenDistMethod has a value of 'downstreamUnsolicited', label bindings are distributed to the upstream LSR only when a label request message is received. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenRetentionMode specifies the label retention mode used. If the value of this object is 'conservative', then advertised label mappings are retained only if they will be used to forward packets, i.e. if the label came from a valid next hop. Label bindings received from non-nexthops for each FEC are discarded. If the value of this object is 'liberal', then all advertised label mappings are retained whether they are from a valid next hop or not. When vRtrLdpGenDistMethod has a value of 'downstreamUnsolicited', a LSR may receive label bindings for the same destination for all its neighbors. Labels for the non-nexthops for the FECs are retained in the software but not used. When a network topology change occurs where a non-nexthop becomes a true next hop, the label received earlier is then used. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenTransportAddrType specifies the source of the transport address to be used when setting up the LDP TCP sessions. The transport address can be configured globally (applied to all interfaces) or per interface. When the value of this object is 'interface', the interface's IP address is used to setup the LDP session between neighbors. If multiple interfaces exist between two neighbors, the 'interface' mode cannot be used since only one LDP session is actually set up between the two neighbors. When the value of this object is 'system', the system's IP address is used to set up the LDP session between neighbors. This value is only applicable to LDP interfaces and not for targeted sessions. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenPropagatePolicy determines whether the LSR should generate FECs and which FECs it should generate. When the value of this object is 'system', LDP will distribute label bindings only for the router's system IP address When the value of this object is 'interface', LDP will distribute label bindings for all LDP interfaces When the value of this object is 'all', LDP will distribute label bindings for all prefixes in the routing table When the value of this object is 'none', LDP will not distribute any label bindings. This value is only applicable to LDP interfaces and not for targeted sessions. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenLoopDetectCapable indicate whether this LSR supports loop detection and if so, what type of loop detection is supported. When the value is 'none' loop detection is not supported on this LSR. When the value is 'other' Loop Detection is supported but by a method other than those listed below. When the value is 'hopCount' Loop Detection is supported by Hop Count only. When the value is 'pathVector' Loop Detection is supported by Path Vector only. When the value is 'hopCountAndPathVector' Loop Detection is supported by both Hop Count and Path Vector. Since Loop Detection is determined during Session Initialization, an individual session may not be running with loop detection. This object simply gives an indication of whether or not the LSR has the ability to support Loop Detection and which types. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenHopLimit specifies the maximum allowable value for the hop count. The value of this object is valid and used only if vRtrLdpGenLoopDetectCapable has a value of either 'hopCount' or 'hopCountAndPathVector'. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenPathVectorLimit specifies the maximum allowable value for the path vector count. The value of this object is valid and used only if vRtrLdpGenLoopDetectCapable has a value of either 'pathVector' or 'hopCountAndPathVector'. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenBackoffTime specifies the initial value for the backoff interval. The backoff interval is the time, in seconds, that LDP waits after an LDP session setup has failed before it attempts to setup the session again. After the LDP session startup fails the first time, the backoff interval is set to the value of vRtrLdpGenBackoffTime. Thereafter, if session startup fails again the backoff interval increases exponentially. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenMaxBackoffTime specifies the maximum value for the backoff interval. For each successive failure of the LDP session startup, the backoff interval (the time for which the router waits before retrying) increases exponentially. If the backoff interval exceeds vRtrLdpGenMaxBackoffTime, the router will give up trying to establish the LDP session. If vRtrLdpGenMaxBackoffTime is set to zero (0), then the backoff interval does not increase exponentially after the first session startup attempt fails. Instead it remains constant and LDP will keep retrying to establish a session until it succeeds. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenTargKeepAliveFactor specifies the value by which the keepalive timeout (vRtrLdpGenTargKeepAliveTimeout) should be divided to give the keepalive time i.e. the time interval, in seconds, between LDP keepalive messages. LDP keepalive messages are sent to keep the LDP session from timing out when no other LDP traffic is being sent between the neighbors. This value is only applicable to targeted sessions and not to LDP interfaces. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenTargKeepAliveTimeout specifies the time interval, in seconds, that LDP waits before tearing down a session. If no LDP messages are exchanged during this time interval, the LDP session is torn down. Generally the value of vRtrLdpGenTargKeepAliveTimeout is configured to be 3 times the keepalive time (the time interval between successive LDP keepalive messages). This value is only applicable to targeted sessions and not to LDP interfaces. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenTargHelloFactor specifies the value by which the hello timeout (vRtrLdpGenTargHelloTimeout) should be divided to give the hello time i.e. the time interval, in seconds, between LDP Hello messages. LDP uses hello messages to discover neighbors and to detect loss of connectivity with its neighbors. This value is only applicable to targeted sessions and not to LDP interfaces. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenTargHelloTimeout specifies the hello time also known as hold time. It is the time interval, in seconds, that LDP waits before declaring a neighbor to be down. Hello timeout is local to the system and is sent in the hello messages to a neighbor. Hello timeout cannot be set to a value that is less than 3 times the hello time. This value is only applicable to targeted sessions and not to LDP interfaces. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenTargPassiveMode specifies the mode used for setting up LDP sessions. When it has a value of 'true', LDP responds only when it gets a connect request from a peer and will not attempt to actively connect to its neighbors. When it has a value of 'false', LDP actively tries to connect to its peers. This value is only applicable to targeted sessions and not to LDP interfaces. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenTargetedSessions specifies whether or not targeted sessions are allowed. Targeted sessions are LDP sessions between indirectly connected peers. The discovery messages for an indirect LDP session are addressed to the specified peer instead of to the multicast address. When this object has a value of 'true', targeted sessions are enabled. When its value is 'false', targeted sessions are disabled. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenCreateTime specifies the sysUpTime when this LDP instance was created. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenUpTime specifies the time, in hundreds of seconds, that the LDP instance has been in current operational state (vRtrLdpGenOperState). If the value of vRtrLdpGenOperState is 'inService (2)', then vRtrLdpGenUpTime specifies the time that the LDP instance has been operationally up. If the value of vRtrLdpGenOperState is 'outOfService (3)', then vRtrLdpGenUpTime specifies the time that the LDP instance has been operationally down. If the value of vRtrLdpGenOperState is 'transition (4)', then vRtrLdpGenUpTime specifies the time that the LDP instance has been operationally in transition. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenImportPolicy1 specifies the first import policy used to filter LDP label bindings received from LDP peers. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenImportPolicy2 specifies the second import policy used to filter LDP label bindings received from LDP peers. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenImportPolicy3 specifies the third import policy used to filter LDP label bindings received from LDP peers. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenImportPolicy4 specifies the fourth import policy used to filter LDP label bindings received from LDP peers. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenImportPolicy5 specifies the fifth import policy used to filter LDP label bindings received from LDP peers. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenExportPolicy1 specifies the first export policy used to filter LDP label bindings advertised to LDP peers. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenExportPolicy2 specifies the second export policy used to filter LDP label bindings advertised to LDP peers. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenExportPolicy3 specifies the third export policy used to filter LDP label bindings advertised to LDP peers. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenExportPolicy4 specifies the fourth export policy used to filter LDP label bindings advertised to LDP peers. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenExportPolicy5 specifies the fifth export policy used to filter LDP label bindings advertised to LDP peers. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenTunnelDownDampTime specifies the time interval, in seconds, that LDP waits before posting a tunnel down event to the Route Table Manager. If a tunnel up event is generated before the damping interval has elapsed, a tunnel modify event will be posted to the Route Table Manager (RTM). If this value is set to 0, then tunnel down events are not damped. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenOperDownReason specifies the reason that the LDP instance is operationally down. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenTrustList specifies the IP filter ID used to verify trusted T-LDP peers. The IP filter specified by this object should contain a list of src-ip matches. The value '0' is not a valid IP filter ID, but it is used to indicate that there is no trust list. This object was obsoleted in release 5.0.

OBJECT-TYPE

The value of vRtrLdpGenGracefulRestart specifies whether graceful restart helper is allowed. When this object has a value of 'true', graceful restart helper is enabled. When its value is 'false', graceful restart helper is disabled. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenGRNbrLiveTime specifies the value for neighbor liveness timer. The amount of time the Label Switching Router (LSR) keeps its stale label-FEC bindings is set to the lesser of the FT Reconnect Timeout, as was advertised by the neighbor, and this local timer, called the Neighbor Liveness Timer. The LSR waits for the specified time till a LDP session re-establishes itself. If within that time the LSR still does not establish an LDP session with the neighbor, all the stale bindings are deleted. This object has meaning only when vRtrLdpGenGracefulRestart is 'true'. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenGRMaxRecoveryTime specifies the local maximum recovery time. If the Label Switching Router (LSR) determines that the neighbor was able to preserve its MPLS forwarding state (as was indicated by the non-zero Recovery Time advertised by the neighbor), the LSR should further keep the stale label-FEC bindings, received from the neighbor, for as long as the lesser of the Recovery Time advertised by the neighbor, and a local configurable value, called Maximum Recovery Time, allows. This object has meaning only when vRtrLdpGenGracefulRestart is 'true'. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenLabelWithdrawalDelay specifies the time interval, in seconds, LDP will delay for the withdrawal of FEC-label binding it distributed to its neighbours when FEC is deactivated. When the timer expires, LDP then sends a label withdrawal for the FEC to all its neighbours. This is applicable only to LDP transport tunnels (ipv4 prefix FECs) and is not applicable to Pseudowires (service FECs). A value of 0 indicates that vRtrLdpGenLabelWithdrawalDelay is disabled. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenImplicitNull specifies whether or not to signal implicit null values for all LDP FECs for which this node is an egress Label Edge Router (LER). When the value is true implicit null values are signaled. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenShortTTLPropLocal specifies whether or not to enable the propagation of time to live (TTL) from the header of IP packet into the header of resulting MPLS packet for all local packets forwarded over a LDP shortcut. When the value is set to 'true' TTL is propagated from the header of IP packet into the header of the resulting MPLS packet for all local packets. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenShortTTLPropTransit specifies whether or not to enable the propagation of time to live (TTL) from the header of IP packet into the header of resulting MPLS packet for all transit packets forwarded over a LDP shortcut. When the value is set to 'true' TTL is propagated from the header of IP packet into the header of the resulting MPLS packet for all transit packets. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenMPMBBTime specifies the maximum time a Multi Point (MP) transit node must wait before switching over to a new path if the new node does not send Make Before Break (MBB) Tag Length Value (TLV) to inform of the availability of the data plane. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenTunlTblExportPolicy1 specifies the first tunnel table export policy used for exporting tunneled routes from the CPM tunnel table as LDP FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenTunlTblExportPolicy2 specifies the second tunnel table export policy used for exporting tunneled routes from the CPM tunnel table as LDP FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenTunlTblExportPolicy3 specifies the third tunnel table export policy used for exporting tunneled routes from the CPM tunnel table as LDP FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenTunlTblExportPolicy4 specifies the fourth tunnel table export policy used for exporting tunneled routes from the CPM tunnel table as LDP FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenTunlTblExportPolicy5 specifies the fifth tunnel table export policy used for exporting tunneled routes from the CPM tunnel table as LDP FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenP2MPCapability specifies whether Point-to-Multipoint (P2MP) FEC capability is supported in the LDP instance or not. When the value is 'true', the LDP instance is P2MP capable. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenMPMBBCapability specifies whether Multipoint(MP) Make-Before-Break (MBB) capability is supported in the LDP instance or not. When the value is 'true', the LDP instance is MP MBB capable. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenDynamicCapability specifies whether dynamic capability negotiation is supported or not in LDP sessions associated with the LDP instance. When 'true', the LDP instance supports dynamic capability negotiation. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenLdpFrr specifies whether fast reroute of LDP tunnel is enabled or disabled. When the value of vRtrLdpGenLdpFrr is set to 'true' fast reroute of LDP tunnel is enabled and when vRtrLdpGenLdpFrr is set to 'false' fast reroute of LDP tunnel is disabled. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenTargHelloReduction specifies whether hello reduction to this targeted peer is enabled or not. If enabled, the sender advertises further dampened vRtrLdpGenTargHelloTimeout, to the targeted peer after LDP session is established. The value of 'true' means targeted hello reduction is enabled. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenTargHelloReductionFctr specifies the number of hello messages that are sent at consistent vRtrLdpGenTargHelloTimeout, before advertising further dampened vRtrLdpGenTargHelloTimeout. An 'inconsistentValue' error is returned if this object is set when vRtrLdpGenTargHelloReduction is disabled. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenMcastUpstreamFrr specifies whether mLDP fast upstream switchover feature is enabled or not for the LDP instance. When 'true', the LDP instance supports mLDP fast upstream switchover. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpGenOverloadCapability indicates whether LSR Overload is supported or not in LDP sessions associated with the LDP instance. When 'true', the LDP instance is LSR overload capable. This object was obsoleted in release 13.0.

OBJECT-TYPE

vRtrLdpStatsTable is a read-only table. The purpose of this table is to keep statistical information about an LDP Instance. Use of AUGMENTS clause implies a one-to-one dependent relationship between the base table, vRtrLdpGeneralTable, and the augmenting table, vRtrLdpStatsTable. This in effect extends the vRtrLdpGeneralTable with additional columns. Creation or deletion of a row in the vRtrLdpGeneralTable results in the same fate for the row in the vRtrLdpStatsTable. In 13.0 this table has been replaced by TIMETRA-LDP-NG-MIB::vLdpNgStatsTable.

OBJECT-TYPE

A row in this table represents statistical information about an LDP instance.

OBJECT-TYPE

The value of vRtrLdpStatsOperDownEvents specifies the number of times the LDP instance has gone operationally down since the instance was created. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpStatsActiveSessions specifies the number of active sessions (i.e. session in some form of creation) associated with the LDP instance. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpStatsActiveAdjacencies specifies the number of active adjacencies (i.e. established sessions) associated with the LDP instance. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpStatsActiveInterfaces specifies the number of active (i.e. operationally up) interfaces associated with the LDP instance. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpStatsInactiveInterfaces specifies the number of inactive (i.e. operationally down) interfaces associated with the LDP instance. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpStatsActiveTargSessions specifies the number of configured targeted peers that are administratively up in an LDP instance. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpStatsInactiveTargSessions specifies the number of inactive (i.e. operationally down) targeted sessions associated with the LDP instance. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpStatsAddrFECRecv specifies the number of Address FECs received by the LDP instance from its neighbors. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpStatsAddrFECSent specifies the number of Address FECs sent by the LDP instance to its neighbors. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpStatsSvcFECRecv specifies the number of Service FECs received by the LDP instance from its neighbors. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpStatsSvcFECSent specifies the number of Service FECs sent by the LDP instance to its neighbors. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpStatsAttemptedSessions specifies the total number of attempted sessions for this LDP instance. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpStatsSessRejNoHelloErrors gives the total number of Session Rejected/No Hello Error Notification Messages sent or received by this LDP instance. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpStatsSessRejAdvErrors gives the total number of Session Rejected/Parameters Advertisement Mode Error Notification Messages sent or received by this LDP instance. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpStatsSessRejMaxPduErrors gives the total number of Session Rejected/Parameters Max Pdu Length Error Notification Messages sent or received by this LDP instance. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpStatsSessRejLabelRangeErrors gives the total number of Session Rejected/Parameters Label Range Error Notification Messages sent or received by this LDP instance. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpStatsBadLdpIdentifierErrors gives the number of Bad LDP Identifier Fatal Errors detected for sessions associated with this LDP instance. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpStatsBadPduLengthErrors gives the number of Bad Pdu Length Fatal Errors detected for sessions associated with this LDP instance. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpStatsBadMessageLengthErrors gives the number of Bad Message Length Fatal Errors detected for sessions associated with this LDP instance. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpStatsBadTlvLengthErrors gives the number of Bad TLV Length Fatal Errors detected for sessions associated with this LDP instance. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpStatsMalformedTlvValueErrors gives the number of Malformed TLV Value Fatal Errors detected for sessions associated with this LDP instance. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpStatsKeepAliveExpiredErrors gives the number of Session Keep Alive Timer Expired Errors detected for sessions associated with this LDP instance. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpStatsShutdownNotifRecv gives the number of Shutdown Notifications received related to sessions associated with this LDP instance. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpStatsShutdownNotifSent gives the number of Shutdown Notifications sent related to sessions associated with this LDP instance. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpStatsEgrFecPfxCount indicates the number of egress FEC prefix statistics configured for this LDP instance. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpStatsUnknownTlvErrors indicates the number of Unknown TLV Fatal Errors detected for sessions associated with this LDP instance. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpStatsP2MPFECSent specifies the number of P2MP FECs sent by the LDP instance to its neighbors. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpStatsP2MPFECRecv specifies the number of P2MP FECs received by the LDP instance from its neighbors. This object was obsoleted in release 13.0.

OBJECT-TYPE

vRtrLdpPolicyTable has an entry for each policy used by the LDP protocol instance running on the virtual router. This table is obsoleted in release 2.1.

OBJECT-TYPE

Each row entry represents a policy used by the LDP protocol instance. Entries can be created and deleted via SNMP SET operations to vRtrLdpPolicyRowStatus. This entry is obsoleted in release 2.1.

OBJECT-TYPE

The value of vRtrLdpPolicyType indicates the type of policy specified in this row entry. When vRtrLdpPolicyType has a value of 'import' this row entry represents the policy filter to be applied to the label binding received from a neighbor. When the value is 'export', this row entry represents the policy filter to determine the labels to be advertised to the neighbors. When the value is 'ingress', this row entry represents the policy filter to control the route prefixes that are advertised by LDP to the route table. LDP will advertise label bindings of prefixes that are advertised into it. When the value is 'egress', this row entry represents the policy filter to control the route prefixes that are advertised into LDP from the route table. LDP will advertise label bindings of prefixes that are advertised into it. This object is obsoleted in release 2.1.

OBJECT-TYPE

vRtrLdpPolicyIndex is used to control the order that the LDP policies are applied. If multiple entries exist in this table with the same vRtrID and vRtrLdpPolicyType indexes, they are evaluated in ascending numeric order of vRtrLdpPolicyIndex (gaps are allowed). The first policy that matches is applied. This object is obsoleted in release 2.1.

OBJECT-TYPE

vRtrLdpPolicyRowStatus controls the creation and deletion of rows in the vRtrLdpPolicyTable. This object is obsoleted in release 2.1.

OBJECT-TYPE

The value of vRtrLdpPolicyName is the name of the policy filter to be used. If this object has the value of the empty string, ''H, there is no policy specified at this level. This object is obsoleted in release 2.1.

OBJECT-TYPE

Voluntary serialization control for vRtrLdpIfTable. Primarily used by SNMP manager to coordinate changes to vRtrLdpIfInheritance.

OBJECT-TYPE

vRtrLdpIfTable provides an entry for each virtual router interface or targeted peer configured to be used with the Label Distribution Protocol (LDP). In 13.0 this table has been replaced by TIMETRA-LDP-NG-MIB::vRtrLdpNgIfTable, TIMETRA-LDP-NG-MIB::vRtrLdpNgInetIfTable.

OBJECT-TYPE

Each row entry represents an interface on this virtual router that participates in the LDP protocol. Row entries can be created or deleted via SNMP SET requests. A row with default attribute values is created by setting vRtrLdpIfRowStatus to 'createAndGo'. A row entry can be destroyed by setting vRtrLdpIfRowStatus to 'destroy'.

OBJECT-TYPE

vRtrLdpIfIndex is an index for the row entry and is used mutually exclusively with the vRtrLdpPeerAddress field. If the vRtrLdpPeerAddress field is 0.0.0.0, then vRtrLdpIfIndex is the index for the interface on the virtual router and must be non-zero. Otherwise, vRtrLdpPeerAddress refers to a targeted peer and its vRtrLdpIfIndex is 0. This object was obsoleted in release 13.0.

OBJECT-TYPE

vRtrLdpPeerAddress is an index for the row entry and is used mutually exclusively with the vRtrLdpIfIndex field. If the vRtrLdpIfIndex field is 0, then the vRtrLdpPeerAddress is the IP address of the targeted peer and must be non-zero. Otherwise, vRtrLdpIfIndex refers to the LDP interface index and its vRtrLdpPeerAddress is 0.0.0.0 This object was obsoleted in release 13.0.

OBJECT-TYPE

vRtrLdpIfRowStatus is used to control the creation and deletion of rows in the vRtrLdpIfTable. A row can be created by setting vRtrLdpIfRowStatus to 'createAndGo'. The agent should assign the default attribute values and change the row status to 'active'. A row entry can be destroyed by setting vRtrLdpIfRowStatus to 'destroy'. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpIfLastChange specifies the sysUpTime when this row was last modified. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpIfAdminState indicates the desired administrative state for LDP on this interface or targeted peer. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpIfOperState specifies the current operational state of LDP on this interface or targeted peer. This object was obsoleted in release 13.0.

OBJECT-TYPE

Some writable object in this row that can be configured to inherit its value from its corresponding object in the vRtrLdpGeneralTable for LDP interfaces or from the corresponding object in the vRtrLdpIfTable for targeted peers. vRtrLdpIfInheritance controls whether to inherit the operational value of that object, or use the administratively set value. Non mask bits will always have value of zero, and any attempt to change the value will be silently discarded. This object is a bit-mask, with the following positions: vRtrLdpIfKeepAliveFactor 0x1 vRtrLdpIfKeepAliveTimeout 0x2 vRtrLdpIfHelloFactor 0x4 vRtrLdpIfHelloTimeout 0x8 vRtrLdpIfBackoffTime 0x10 vRtrLdpIfMaxBackoffTime 0x20 vRtrLdpIfTransportAddrType 0x40 vRtrLdpIfPassiveMode 0x80 vRtrLdpIfHelloReduction 0x100 vRtrLdpIfHelloReductionFactor 0x200 When the bit for an object has value of one, then the object's administrative and operational value are whatever the DEFVAL or most recently SET value. The mask bit(s) will be set to one when set is performed on the inherited object(s). Any attempt to set the mask bit to one will be silently discarded. When the bit for an object is set to zero, then the object's administrative and operational value are inherited from the corresponding object in vRtrLdpGeneralTable for LDP interfaces or the vRtrLdpIfTable for targeted peers. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpIfKeepAliveFactor specifies the value by which the keepalive timeout (vRtrLdpIfKeepAliveTimeout) should be divided to give the keepalive time i.e. the time interval, in seconds, between LDP keepalive messages. LDP keepalive messages are sent to keep the LDP session from timing out when no other LDP traffic is being sent between the neighbors. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpIfKeepAliveTimeout specifies the time interval, in seconds, that LDP waits before tearing down a session. If no LDP messages are exchanged during this time interval, the LDP session is torn down. Generally the value of vRtrLdpIfKeepAliveTimeout is configured to be 3 times the keepalive time (the time interval between successive LDP keepalive messages). This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpIfHelloFactor specifies the value by which the hello timeout (vRtrLdpIfHelloTimeout) should be divided to give the hello time i.e. the time interval, in seconds, between LDP Hello messages. LDP uses hello messages to discover neighbors and to detect loss of connectivity with its neighbors. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpIfHelloTimeout specifies the hello time also known as hold time. It is the time interval, in seconds, that LDP waits before declaring a neighbor to be down. Hello timeout is local to the system and is sent in the hello messages to a neighbor. Hello timeout cannot be set to a value that is less than 3 times the hello time. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpIfBackoffTime specifies the initial value for the backoff interval. The backoff interval is the time, in seconds, that LDP waits after an LDP session setup has failed before it attempts to setup the session again. After the LDP session startup fails the first time, the backoff interval is set to the value of vRtrLdpIfBackoffTime. Thereafter, if session startup fails again the backoff interval increases exponentially. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpIfMaxBackoffTime specifies the maximum value for the backoff interval. For each successive failure of the LDP session startup, the backoff interval (the time for which the router waits before retrying) increases exponentially. If the backoff interval exceeds vRtrLdpIfMaxBackoffTime, the router will give up trying to establish the LDP session. If vRtrLdpIfMaxBackoffTime is set to zero (0), then the backoff interval does not increase exponentially after the first session startup attempt fails. Instead it remains constant and LDP will keep retrying to establish a session until it succeeds. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpIfTransportAddrType specifies the source of the transport address to be used when setting up the LDP TCP sessions. This value is meaningful only in case of LDP interfaces and not for targeted peers. When the value of this object is 'interface', the interface's IP address is used to setup the LDP session between neighbors. If multiple interfaces exist between two neighbors, the 'interface' mode cannot be used since only one LDP session is actually set up between the two neighbors. When the value of this object is 'system', the system's IP address is used to set up the LDP session between neighbors. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpIfPassiveMode specifies the mode used for setting up LDP sessions. This object is meaningful only in case of LDP targeted peers and not for interfaces. When it has a value of 'true', LDP responds only when it gets a connect request from a peer and will not attempt to actively connect to its neighbors. When it has a value of 'false', LDP actively tries to connect to its peers. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpIfAutoCreate specifies whether or not the row entry was automatically created. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpIfOperDownReason specifies the reason that the LDP interface or targeted peer is operationally down. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpIfTunneling specifies whether tunneling of LDP over tunnels is enabled. When this object has a value of 'true', tunneling is enabled. When its value is 'false', tunneling is disabled. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpIfBfdEnabled specifies whether BFD tracking of a LDP Session on this interface is enabled. When this object has a value of 'true', BFD tracking is enabled. When its value is 'false', BFD tracking is disabled. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpIfLinkLsrIfType specifies whether the local interface address or the system interface address should be used as source Label Switch Router identifier (LSR-ID) to establish a link LDP adjacency with a LDP peer. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpIfTargLsrIfIndex specifies the local interface index that is to be used as source LSR-ID to establish targeted hello adjacency with a LDP peer. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpIfMulticast specifies whether multicast traffic forwarding is enabled or disabled on the interface. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpIfHelloReduction specifies whether hello reduction to this targeted peer is enabled or not. If enabled, the sender advertises the dampened vRtrLdpIfHelloTimeout, to the targeted peer after LDP session is established. The value of this object is valid only for LDP targeted peers and not for interfaces. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpIfHelloReductionFactor specifies the number of hello messages that are sent at consistent vRtrLdpIfHelloTimeout, before advertising further dampened vRtrLdpIfHelloTimeout. An 'inconsistentValue' error is returned if this object is set when vRtrLdpIfHelloReduction is disabled. The object is set to '0' for LDP interfaces to indicate that the hello reduction feature is not applicable. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpIfOperHelloTimeout indicates the operational hello time also known as hold time used by the operational targeted peer or LDP interface. It is the time interval that LDP waits before declaring a neighbor to be down. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpIfLinkLsrIfIndex specifies the local interface index that is to be used as source LSR-ID to establish link hello adjacency with a LDP peer. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpIfCreator indicates the creator of this row. A value of 'manual(1)' indicates the entry is created manually by the user. A value of 'template(2)' indicates the entry is auto created by template configuration. A value of 'sdp(3)' indicates the entry is auto created by service manager. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpIfTemplName specifies the template name that created this row. This object has valid value when vRtrLdpIfCreator has value of template. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpIfUpTime indicates the time, in hundreds of seconds, that the LDP interface or targeted peer has been in current operational state vRtrLdpIfOperState. If the value of vRtrLdpIfOperState is 'inService (2)', then vRtrLdpIfUpTime specifies the time that the LDP interface or targeted peer has been operationally up. If the value of vRtrLdpIfOperState is 'outOfService (3)', then vRtrLdpIfUpTime specifies the time that the LDP interface or targeted peer has been operationally down. If the value of vRtrLdpIfOperState is 'transition (4)', then vRtrLdpIfUpTime specifies the time that the LDP instance has been operationally in transition. This object was obsoleted in release 13.0.

OBJECT-TYPE

vRtrLdpIfStatsTable is a read-only table. The purpose of this table is to keep statistical information about the LDP Interfaces and Targeted peers on the LSR. Use of AUGMENTS clause implies a one-to-one dependent relationship between the base table, vRtrLdpIfTable, and the augmenting table, vRtrLdpIfStatsTable. This in effect extends the vRtrLdpIfTable with additional columns. Creation or deletion of a row in the vRtrLdpIfTable results in the same fate for the row in the vRtrLdpIfStatsTable. In 13.0 this table has been replaced by TIMETRA-LDP-NG-MIB::vRtrLdpNgInetIfStatsTable.

OBJECT-TYPE

A row in this table contains statistical information about an LDP Interface or Targeted peer. Some counters contained in a row are for fatal errors received during a former LDP Session associated with this entry. For example, an LDP Pdu received on a TCP connection during an LDP Session contains a fatal error. That error is counted here, because the session is terminated. If the error is NOT fatal (i.e. and the Session remains), then the error is counted in the vRtrLdpSessionStatsEntry.

OBJECT-TYPE

The value of vRtrLdpIfExistingAdjacencies gives a count of the total active adjacencies on this LDP interface or with this targeted peer. This object was obsoleted in release 13.0.

OBJECT-TYPE

vRtrLdpHelloAdjTable is a read-only table. The purpose of this table is to keep information about Hello Adjacencies for Sessions. A hello adjacency can be associated with an LDP interface or with a targeted peer. The index includes both the interface index and the peer IP address thus referring to the LDP interface or targeted peer. In 13.0 this table has been replaced by TIMETRA-LDP-NG-MIB::vRtrLdpNgHelloAdjTable.

OBJECT-TYPE

Each row represents a single LDP Hello Adjacency. An LDP Session can have one or more Hello adjacencies.

OBJECT-TYPE

vRtrLdpPeerLdpId is an index for the row entry. It indicates the LDP identifier of the peer. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpHelloAdjLocalLdpId indicates the local LDP identifier for this specific adjacency. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpHelloAdjEntityIndex indicates the Entity index which is an index for the mplsLdpHelloAdjacencyEntry defined in MPLS-LDP-MIB. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpHelloAdjIndex indicates the Hello adjacency index which is an index for the mplsLdpHelloAdjacencyEntry defined in MPLS-LDP-MIB. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpHelloAdjHoldTimeRemaining indicates the hold time remaining for this Hello Adjacency. This interval will change when the next Hello message which corresponds to this Hello Adjacency is received. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpHelloAdjType indicates the type of this Hello Adjacency. If this value is 'link' then this adjacency is a result of a Link Hello. If this value is 'hello', then the adjacency is a result of a Targeted Hello. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpHelloAdjRemoteConfSeqNum indicates the Configuration sequence number that was in the Hello received when this adjacency started up. This configuration sequence number changes when there is a change of configuration. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpHelloAdjRemoteIpAddress indicates the peer IP address of the interface/targeted session that sent hellos for this specific adjacency. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpHelloAdjUpTime indicates the time, in hundreds of seconds, that this adjacency has been up. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpHelloAdjLocalConfSeqNum indicates the Configuration sequence number that was used in the Hello sent when this adjacency started up. This configuration sequence number changes when there is a change of configuration. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpHelloAdjLocalIpAddress indicates the local IP address of the interface/targeted session used in Hellos sent for this specific adjacency. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpHelloAdjInHelloMsgCount indicates the number of Hello messages that have been received for this adjacency. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpHelloAdjOutHelloMsgCount indicates the number of Hello messages that have been sent for this adjacency. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpHelloAdjLocalHelloTimeout indicates the hello timeout used in the Hellos sent for this specific adjacency. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpHelloAdjRemoteHelloTimeout indicates the hello timeout used by the remote end that sent Hellos for this specific adjacency. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpHelloAdjBfdStatus indicates the BFD operational status for LDP hello adjacency. If the value of vRtrLdpHelloAdjBfdStatus is 'noService', BFD is not enabled for LDP hello adjacency. If the value of the object is 'outOfService', BFD is enabled but it is down and not running. If the value of object is 'inService', BFD is enabled and it is running. This object was obsoleted in release 13.0.

OBJECT-TYPE

vRtrLdpHelloAdjMapTable is a read-only table which maps to the vRtrLdpHelloAdjTable. This table has the same indexes as the vRtrLdpHelloAdjTable but the order in which these indexes are specified is different for the two tables. In 13.0 this table has been replaced by TIMETRA-LDP-NG-MIB::vRtrLdpNgHelloAdjMapTable.

OBJECT-TYPE

Each row represents a single LDP Hello Adjacency. An LDP Session can have one or more Hello adjacencies.

OBJECT-TYPE

vRtrLdpHelloAdjMapLdpId is an index for the row entry. It specifies the LDP identifier of the peer. This object was obsoleted in release 13.0.

OBJECT-TYPE

vRtrLdpSessionTable is a read-only table which parallels the mplsLdpSessionTable in the MPLS-LDP-MIB. The purpose of this table is to keep information about a single session between an LDP entity and an LDP Peer. In 13.0 this table has been replaced by TIMETRA-LDP-NG-MIB::vRtrLdpNgSessionTable.

OBJECT-TYPE

A row in this table represents information about a single session between an LDP entity and an LDP Peer.

OBJECT-TYPE

The value of vRtrLdpSessLocalLdpId specifies the local LDP identifier for this LDP session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessEntityIndex specifies the Entity index for the LDP entity represented in this session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessLabelDistMethod specifies the label distribution method used for this LDP session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessLoopDetectForPV indicates whether loop detection based on path vectors is disabled or enabled for this LDP session. If this object has a value of disabled(0), then loop detection is disabled. Otherwise, if this object has a value of enabled(1), then loop detection based on path vectors is enabled. This object was obsoleted in release 13.0.

OBJECT-TYPE

If the value of vRtrLdpSessLoopDetectForPV for this entry is 'enabled', then the value of vRtrLdpSessPathVectorLimit represents the Path Vector Limit for this LDP Session. If the value of vRtrLdpSessLoopDetectForPV for this entry is 'disabled', then the value of vRtrLdpSessPathVectorLimit be 0 (zero). This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessState specifies the current state of the LDP session. All of the states 1 - 5 are based on the state machine for session negotiation behavior. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessAdjacencyType specifies the adjacency type(s) supporting this LDP Session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessProtocolVersion specifies the version of the LDP Protocol used by this session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessLocalUdpPort specifies the UDP port used locally for LDP discovery. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessPeerUdpPort specifies the UDP port used on the remote end for LDP discovery. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessLocalTcpPort specifies the TCP port used locally for the LDP Session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessPeerTcpPort specifies the TCP port used on the remote end for the LDP Session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessLocalAddress specifies the IP address used locally for the LDP Session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessPeerAddress specifies the IP address used on the remote end for the LDP Session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessKAHoldTimeRemaining specifies the keep alive hold time remaining, in hundredths of seconds, for this LDP session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessMaxPduLength specifies the maximum allowable length for LDP PDUs for this session. This value may have been negotiated during Session Initialization. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessUpTime specifies the time, in hundreds of seconds, since the session was established. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessLocalKATimeout specifies the keepalive timeout used locally for the LDP Session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessPeerKATimeout specifies the keepalive timeout used at the remote end of the LDP Session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessAdvertise indicates the type of FECs that will be transported by the session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessRestartHelperState indicates whether the entity session is capable of supporting graceful restart. This is negotiated between peers during the session initialization setup. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessPeerNumRestart indicates the number of times graceful restart helper was initiated for this session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessLastRestartTime indicates the last time graceful restart helper was initiated. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessFtReconnectTimeNego indicates the session's Fault Tolerant(FT) Reconnect Timeout, it is set to the lesser of the neighbor advertised FT Reconnect Timeout, vRtrLdpSessFtReconTimeRemaining and the local timer Neighbor Liveness Time, vRtrLdpGenGRNbrLiveTime. It is within this period that the transport session is expected to re-establish, failure to do so will cause the teardown of the LDP session and deletion of stale bindings. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessFtRecoveryTimeNego indicates the session's Fault Tolerant(FT) recovery timeout, it is set to the lesser of the neighbor advertised FT recovery timeout, vRtrLdpSessFtRecovTimeRemaining and the local timer maximum recovery time, vRtrLdpGenGRMaxRecoveryTime. It is within this period that label-FEC binding message exchanges are expected to complete. Any stale FEC entries left after this time will be deleted from the FEC table. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessFtReconTimeRemaining indicates the amount of time left before the session's Fault Tolerant(FT) reconnect timeout,vRtrLdpSessFtReconnectTimeNego expires. This object was obsoleted in release 13.0.

OBJECT-TYPE

This value indicates the amount of time left before session's Fault Tolerant(FT) recovery timeout, vRtrLdpSessFtRecoveryTimeNego expires. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessBfdStatus indicates the BFD operational status for the LDP session. If the value of vRtrLdpSessBfdStatus is 'noService', BFD is not enabled for the LDP session. If the value of the object is 'outOfService', BFD is enabled but it is down and not running. If the value of object is 'inService', BFD is enabled and it is running. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessP2MPCapabilityNego indicates whether the entity session is capable of exchanging P2MP FECs. This is negotiated between peers during the session initialization setup. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessMPMBBCapabilityNego indicates whether the entity session is capable of Multipoint MBB. This is negotiated between peers during the session initialization setup. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessDynamicCapabilityNego indicates whether the entity session supports negotiation of LDP session capabilities dynamically. This is negotiated between peers during the session initialization setup. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessOvrloadCapabltyNego indicates whether the entity session is capable of signaling LSR Overload Notification.This is negotiated between peers during the session initialization setup. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessAddrFecOverloadSent indicates whether LSR Overload Notification has been sent to the LDP peer for Address FEC Types. The value of 'true' indicates that Local LSR has set the LDP session as overloaded for Address FEC types and is not ready to receive new Label Mappings for Address FEC Types. In this state if a Label Mapping Message is received from peer for any Address FEC type then the Label is returned with a Label Release Message. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessAddrFecOverloadRecv indicates whether LSR Overload Notification has been received from the LDP peer for Address FEC Types. The value of 'true' indicates that Peer LSR has set the LDP session as overloaded for Address FEC types and is not ready to receive new Label Mappings for any Address FEC Type. In this state no new Label Mapping Message would be sent to peer for any Address FEC Type. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessMcastFecOverloadSent indicates whether LSR Overload Notification has been sent to the LDP peer for Multicast FEC Types. The value of 'true' indicates that Local LSR has set the LDP session as overloaded for Multicast FEC types and is not ready to receive new Label Mappings for Multicast FEC Types. In this state if a Label Mapping Message is received from peer for Multicast FEC types then the Label is returned with a Label Release Message. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessMcastFecOverloadRecv indicates whether LSR Overload Notification has been received from the LDP peer for Multicast FEC Types. The value of 'true' indicates that Peer LSR has set the LDP session as overloaded for Multicast FEC types and is not ready to receive new Label Mappings for any Multicast FEC Type. In this state no new Label Mapping Message would be sent to peer for any Multicast FEC Type. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessServFecOverloadSent indicates whether LSR Overload Notification has been sent to the LDP peer for Service FEC Types. The value of 'true' indicates that Local LSR has set the LDP session as overloaded for Service FEC types and is not ready to receive new Label Mappings for Service FEC Types. In this state if a Label Mapping Message is received from peer for Service FEC types then the Label is returned with a Label Release Message. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessServFecOverloadRecv indicates whether LSR Overload Notification has been received from the LDP peer for Service FEC Types. The value of 'true' indicates that Peer LSR has set the LDP session as overloaded for Service FEC types and is not ready to receive new Label Mappings for any Service FEC Type. In this state no new Label Mapping Message would be sent to peer for any Service FEC Type. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessOperMaxFecThreshold indicates the operational percentage of vRtrLdpPeerMaxFec. This object was obsoleted in release 13.0.

OBJECT-TYPE

vRtrLdpSessionStatsTable is a read-only table. The purpose of this table is to keep statistical information about a single session between an LDP entity and an LDP Peer. Use of AUGMENTS clause implies a one-to-one dependent relationship between the base table, vRtrLdpSessionTable, and the augmenting table, vRtrLdpSessionStatsTable. This in effect extends the vRtrLdpSessionTable with additional columns. Creation or deletion of a row in the vRtrLdpSessionTable results in the same fate for the row in the vRtrLdpSessionStatsTable. In 13.0 this table has been replaced by TIMETRA-LDP-NG-MIB::vRtrLdpNgSessionStatsTable.

OBJECT-TYPE

A row in this table represents statistical information about a single session between an LDP entity and an LDP Peer.

OBJECT-TYPE

The value of vRtrLdpSessStatsTargAdj specifies the number of targeted adjacencies for this session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessStatsLinkAdj specifies the number of link adjacencies for this session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessStatsFECRecv counts the number of FECs received for this session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessStatsFECSent counts the number of FECs sent for this session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessStatsHelloIn counts the number of Hello Messages that have been received during this session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessStatsHelloOut counts the number of Hello Messages that have been sent during this session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessStatsKeepaliveIn counts the number of Keepalive Messages that have been received during this session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessStatsKeepaliveOut counts the number of Keepalive Messages that have been sent during this session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessStatsInitIn counts the number of Init Messages that have been received during this session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessStatsInitOut counts the number of Init Messages that have been sent during this session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessStatsLabelMappingIn counts the number of Label Mapping Messages that have been received during this session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessStatsLabelMappingOut counts the number of Label Mapping Messages that have been sent during this session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessStatsLabelRequestIn counts the number of Label Request Messages that have been received during this session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessStatsLabelRequestOut counts the number of Label Request Messages that have been sent during this session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessStatsLabelReleaseIn counts the number of Label Release Messages that have been received during this session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessStatsLabelReleaseOut counts the number of Label Release Messages that have been sent during this session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessStatsLabelWithdrawIn counts the number of Label Withdraw Messages that have been received during this session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessStatsLabelWithdrawOut counts the number of Label Withdraw Messages that have been sent during this session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessStatsLabelAbortIn counts the number of Label Abort Messages that have been received during this session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessStatsLabelAbortOut counts the number of Label Abort Messages that have been sent during this session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessStatsAddrIn counts the number of Address Messages that have been received during this session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessStatsAddrOut counts the number of Address Messages that have been sent during this session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessStatsAddrWithdrawIn counts the number of Address Withdraw Messages that have been received during this session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessStatsAddrWithdrawOut counts the number of Address Withdraw Messages that have been sent during this session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessStatsNotificationIn counts the number of Notification Messages that have been received during this session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessStatsNotificationOut counts the number of Notification Messages that have been sent during this session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessStatsAddrRecv counts the number of local addresses received for this session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessStatsAddrSent counts the number of local addresses sent for this session. This object was obsoleted in release 13.0.

OBJECT-TYPE

vRtrLdpServFecTable is a read-only table that represents all service FECs either sent to or received from an LDP peer known to the Virtual Router. In 13.0 this table has been replaced by TIMETRA-LDP-NG-MIB::vLdpNgSvcFec128Table, TIMETRA-LDP-NG-MIB::vLdpNgSvcFec128InLblTable, TIMETRA-LDP-NG-MIB::vLdpNgSvcFec128OutLblTable.

OBJECT-TYPE

Each row entry represents an instance of a service FEC sent to or received from an LDP peer.

OBJECT-TYPE

The value of vRtrLdpServFecFecType specifies the FEC type. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecVcType specifies the VC type associated with this service FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecVcId specifies the VC identifier associated with this service FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecServType specifies the Service type associated with this service FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecServId specifies the Service identifier associated with this service FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecVpnId identifies the VPN associated with the FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

The bit flags of vRtrLdpServFecFlags specify the characteristics of the FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecNumInLabels gives the number of labels that have been sent to the peer associated with this FEC. This value also indicates which of the following vRtrLdpServFecInLabel1 thru vRtrLdpServFecInLabel5 entries contain valid information i.e. if the value of vRtrLdpServFecNumInLabels is 3 then vRtrLdpServFecInLabel1, vRtrLdpServFecInLabel2 and vRtrLdpServFecInLabel3 will contain valid label information. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecNumOutLabels gives the number of labels that have been received from the peer associated with this FEC. This value also indicates which of the following vRtrLdpServFecOutLabel1 thru vRtrLdpServFecOutLabel5 entries contain valid information i.e. if the value of vRtrLdpServFecNumOutLabels is 3, then vRtrLdpServFecOutLabel1, vRtrLdpServFecOutLabel2 and vRtrLdpServFecOutLabel3 will contain valid label information. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecInLabel1 specifies the first ingress label exchanged. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecInLabelStatus1 specifies the status of the ingress label 1. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecInLabel2 specifies the second ingress label (if at all) exchanged. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecInLabelStatus2 specifies the status of the ingress label 2. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecInLabel3 specifies the third ingress label (if at all) exchanged. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecInLabelStatus3 specifies the status of the ingress label 3. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecInLabel4 specifies the fourth ingress label (if at all) exchanged. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecInLabelStatus4 specifies the status of the ingress label 4. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecInLabel5 specifies the fifth ingress label (if at all) exchanged. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecInLabelStatus5 specifies the status of the ingress label 5. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecOutLabel1 specifies the first egress label exchanged. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecOutLabelStatus1 specifies the status of the egress label 1. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecOutLabel2 specifies the second egress label (if at all) exchanged. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecOutLabelStatus2 specifies the status of the egress label 2. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecOutLabel3 specifies the third egress label (if at all) exchanged. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecOutLabelStatus3 specifies the status of the egress label 3. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecOutLabel4 specifies the fourth egress label (if at all) exchanged. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecOutLabelStatus4 specifies the status of the egress label 4. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecOutLabel5 specifies the fifth egress label (if at all) exchanged. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecOutLabelStatus5 specifies the status of the egress label 5. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecSdpId identifies the SDP associated with this peer. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecLocalMTU specifies the largest service frame size (in octets) that can be handled by the local ESR. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecRemoteMTU specifies the largest service frame size (in octets) that can be handled by the remote ESR. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecLocalVlanTag specifies the local tag on a VLAN VC type SDP binding. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecRemoteVlanTag specifies the remote tag on a VLAN VC type SDP binding. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecLocalMaxCellConcat specifies the local maximum number of ATM cells to concatenate on a ATM cell-mode VC type SDP binding. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecRemoteMaxCellConcat specifies the remote maximum number of ATM cells to concatenate on a ATM cell-mode VC type SDP binding. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecInLabelSigStatus1 indicates the signaling status for vRtrLdpServFecInLabel1. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecInLabelSigStatus2 indicates the signaling status for vRtrLdpServFecInLabel2. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecInLabelSigStatus3 indicates the signaling status for vRtrLdpServFecInLabel3. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecInLabelSigStatus4 indicates the signaling status for vRtrLdpServFecInLabel4. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecInLabelSigStatus5 indicates the signaling status for vRtrLdpServFecInLabel5. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecOutLabelSigStatus1 indicates the signaling status for vRtrLdpServFecOutLabel1. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecOutLabelSigStatus2 indicates the signaling status for vRtrLdpServFecOutLabel2. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecOutLabelSigStatus3 indicates the signaling status for vRtrLdpServFecOutLabel3. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecOutLabelSigStatus4 indicates the signaling status for vRtrLdpServFecOutLabel4. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecOutLabelSigStatus5 indicates the signaling status for vRtrLdpServFecOutLabel5. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecMateEndpointVcId specifies the VC identifier associated with this service FEC mate endpoint for vc-switching. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecMateEndpointSdpId identifies the SDP associated with this service FEC mate endpoint for vc-switching. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecLocalIpv4Capblty indicates whether or not the local ipv4 stack capability is supported for this LDP peer. The value of vRtrLdpServFecLocalIpv4Capblty is 'true' when the local ipv4 stack capability is supported and the value is 'false' when the local ipv4 stack capability is not supported. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecRemoteIpv4Capblty indicates whether or not the remote ipv4 stack capability is supported for this LDP peer. The value of vRtrLdpServFecLocalIpv4Capblty is 'true' when the remote ipv4 stack capability is supported and the value is 'false' when the remote ipv4 stack capability is not supported. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecLocalIpv6Capblty indicates whether or not the local ipv6 stack capability is supported for this LDP peer. The value of vRtrLdpServFecLocalIpv6Capblty is 'true' when the local ipv6 stack capability is supported and the value is 'false' when the local ipv6 stack capability is not supported. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecRemoteIpv6Capblty indicates whether or not the remote ipv6 stack capability is supported for this LDP peer. The value of vRtrLdpServFecRemoteIpv6Capblty is 'true' when the remote ipv6 stack capability is supported and the value is 'false' when the remote ipv6 stack capability is not supported. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecLocalIpv4CeIpAddr indicates the local ipv4 CE Address. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecRemoteIpv4CeIpAddr indicates the remote ipv4 CE Address. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecInLbl1WdwReason indicates the reason of withdrawal of ingress label value in vRtrLdpServFecInLabel1. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecLocalFLTxCapblty indicates whether or not this LDP peer is capable of sending Flow Label in its pseudowire (PW) packet. The value of vRtrLdpServFecLocalFLTxCapblty is 'true' when this LDP peer is capable of sending Flow Label and the value is 'false' when the peer is not capable of sending Flow Label in pseudowire packet. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecLocalFLRxCapblty indicates whether or not this LDP peer is capable of receiving Flow Label in its pseudowire packet. The value of vRtrLdpServFecLocalFLRxCapblty is 'true' when this LDP peer is capable of receiving Flow Label and the value is 'false' when the peer is not capable of receiving Flow Label in pseudowire packet. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecRemoteFLTxCapblty indicates whether or not the remote LDP peer is capable of sending Flow Label in its pseudowire packet. The value of vRtrLdpServFecRemoteFLTxCapblty is 'true' when the remote LDP peer is capable of sending Flow Label and the value is 'false' when the peer is not capable of sending Flow Label in pseudowire packet. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpServFecRemoteFLRxCapblty indicates whether or not the remote LDP peer is capable of receiving Flow Label in its pseudowire packet. The value of vRtrLdpServFecRemoteFLRxCapblty is 'true' when the remote LDP peer is capable of receiving Flow Label and the value is 'false' when the peer is not capable of receiving Flow Label in pseudowire packet. This object was obsoleted in release 13.0.

OBJECT-TYPE

vRtrLdpServFecMapTable is a read-only table which maps to the vRtrLdpServFecTable. This table has the same indexes as the vRtrLdpServFecTable but the order in which these indexes are specified is different for the two tables.

OBJECT-TYPE

Each row entry represents an instance of a service FEC sent to or received from an LDP peer.

OBJECT-TYPE

The value of vRtrLdpServFecMapFecType specifies the FEC type.

OBJECT-TYPE

The value of vRtrLdpServFecMapVcType specifies the VC type associated with this service FEC.

OBJECT-TYPE

The value of vRtrLdpServFecMapVcId specifies the VC identifier associated with this service FEC.

OBJECT-TYPE

vRtrLdpAddrFecTable is a read-only table that represents all address FECs either sent to or received from an LDP peer known to the Virtual Router.

OBJECT-TYPE

Each row entry represents an instance of an address FEC sent to or received from an LDP peer.

OBJECT-TYPE

The value of vRtrLdpAddrFecFecType specifies the FEC type. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecIpPrefix specifies the IP Address Prefix for this address FEC. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecIpMask specifies the IP Address Mask for this address FEC. This object was obsoleted in release 10.0.

OBJECT-TYPE

The bit flags of vRtrLdpAddrFecFlags specify the characteristics of the FEC. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecNumInLabels gives the number of labels that have been sent to the peer associated with this FEC. This value also indicates which of the following vRtrLdpAddrFecInLabel1 thru vRtrLdpAddrFecInLabel5 entries contain valid information i.e. if the value of vRtrLdpAddrFecNumInLabels is 3 then vRtrLdpAddrFecInLabel1, vRtrLdpAddrFecInLabel2 and vRtrLdpAddrFecInLabel3 will contain valid label information. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecNumOutLabels gives the number of labels that have been received from the peer associated with this FEC. This value also indicates which of the following vRtrLdpAddrFecOutLabel1 thru vRtrLdpAddrFecOutLabel5 entries contain valid information i.e. if the value of vRtrLdpAddrFecNumOutLabels is 3, then vRtrLdpAddrFecOutLabel1, vRtrLdpAddrFecOutLabel2 and vRtrLdpAddrFecOutLabel3 will contain valid label information. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecInLabel1 specifies the first ingress label exchanged This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecInLabelStatus1 specifies the status of the ingress label 1 This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecInLabelIfIndex1 specifies the interface index for ingress label 1. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecInLabel2 specifies the second ingress label (if at all) exchanged. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecInLabelStatus2 specifies the status of the ingress label. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecInLabelIfIndex2 specifies the interface index for ingress label 2. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecInLabel3 specifies the third ingress label (if at all) exchanged. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecInLabelStatus3 specifies the status of the ingress label 3. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecInLabelIfIndex3 specifies the interface index for ingress label 3. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecInLabel4 specifies the fourth ingress label (if at all) exchanged. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecInLabelStatus4 specifies the status of the ingress label 4. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecInLabelIfIndex4 specifies the interface index for ingress label 4. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecInLabel5 specifies the fifth ingress label (if at all) exchanged. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecInLabelStatus5 specifies the status of the ingress label 5. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecInLabelIfIndex5 specifies the interface index for ingress label 5. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLabel1 specifies the first egress label exchanged. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLabelStatus1 specifies the status of the egress label 1. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLabelIfIndex1 specifies the interface index for egress label 1. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLabelNextHop1 specifies the IP address of the next hop for egress label 1. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLabel2 specifies the second egress label (if at all) exchanged. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLabelStatus2 specifies the status of the egress label 2. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLabelIfIndex2 specifies the interface index for egress label 2. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLabelNextHop2 specifies the IP address of the next hop for egress label 2. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLabel3 specifies the third egress label (if at all) exchanged. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLabelStatus3 specifies the status of the egress label 3. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLabelIfIndex3 specifies the interface index for egress label 3. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLabelNextHop3 specifies the IP address of the next hop for egress label 3. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLabel4 specifies the fourth egress label (if at all) exchanged. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLabelStatus4 specifies the status of the egress label 4. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLabelIfIndex4 specifies the interface index for egress label 4. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLabelNextHop4 specifies the IP address of the next hop for egress label 4. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLabel5 specifies the fifth egress label (if at all) exchanged. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLabelStatus5 specifies the status of the egress label 5. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLabelIfIndex5 specifies the interface index for egress label 5. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLabelNextHop5 specifies the IP address of the next hop for egress label 5. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecLspId indicates the LSP id of the LSP for the RSVP tunnel used by LDP in LDP over RSVP associated with egress label 1. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecLspId2 indicates the LSP id of the LSP for the RSVP tunnel used by LDP in LDP over RSVP associated with egress label 2. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecLspId3 indicates the LSP id of the LSP for the RSVP tunnel used by LDP in LDP over RSVP associated with egress label 3. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecLspId4 indicates the LSP id of the LSP for the RSVP tunnel used by LDP in LDP over RSVP associated with egress label 4. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecLspId5 indicates the LSP id of the LSP for the RSVP tunnel used by LDP in LDP over RSVP associated with egress label 5. This object was obsoleted in release 10.0.

OBJECT-TYPE

vRtrLdpAddrFecMapTable is a read-only table which maps to the vRtrLdpAddrFecTable. This table has the same indexes as the vRtrLdpAddrFecTable but the order in which these indexes are specified is different for the two tables.

OBJECT-TYPE

Each row entry represents an instance of an address FEC sent to or received from an LDP peer.

OBJECT-TYPE

The value of vRtrLdpAddrFecMapFecType specifies the FEC type. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecMapIpPrefix specifies the IP Address Prefix for this address FEC. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecMapIpMask specifies the IP Address Mask for this address FEC. This object was obsoleted in release 10.0.

OBJECT-TYPE

vRtrLdpAdjBackoffTable is a read-only table which augments the vRtrLdpHelloAdjTable. The purpose of this table is to keep backoff information about the LDP Hello Adjacencies on the virtual router. Use of AUGMENTS clause implies a one-to-one dependent relationship between the base table, vRtrLdpHelloAdjTable, and the augmenting table vRtrLdpAdjBackoffTable. This in effect extends the vRtrLdpHelloAdjTable with additional columns. Creation or deletion of a row in the vRtrLdpHelloAdjTable results in the same fate for the row in the vRtrLdpAdjBackoffTable.

OBJECT-TYPE

A row in this table contains backoff information about an LDP adjacency. When an LDP session startup fails for the first time, the LDP entity waits for a certain time interval before it tries to setup the session again. This interval is the backoff interval. The initial value for the backoff interval is set to the value of vRtrLdpAdjInitBackoff. After waiting for the backoff interval, LDP retries to setup the LDP session. If it fails again the backoff interval increases exponentially and this repeats for each successive LDP session startup failure. If the backoff interval exceeds vRtrLdpAdjMaxBackoff, LDP will not backoff anymore and will give up trying to establish the LDP session.

OBJECT-TYPE

The value of vRtrLdpAdjInitBackoff specifies the initial backoff time. After a LDP session setup has failed, the value of vRtrLdpAdjInitBackoff is the time interval, in seconds, that the LDP entity waits before attempting to setup the session again. This interval is the backoff interval. This variable indicates the initial value for backoff interval when the LDP session startup first fails. Thereafter, if session startup fails again the backoff interval increases exponentially. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpAdjMaxBackoff specifies the maximum backoff time. For each successive failure of the LDP session startup, the backoff interval (the time for which the router waits before retrying) increases exponentially. If the backoff interval exceeds vRtrLdpAdjMaxBackoff, the router will not backoff anymore and will give up trying to establish the LDP session. A value of 0 for vRtrLdpAdjMaxBackoff indicates that the backoff interval remains constant and will not increase exponentially. In effect the router will try to establish an LDP session till it succeeds. This object was obsoleted in release 13.0.

OBJECT-TYPE

This value of vRtrLdpAdjCurrentBackoff specifies the current value of the backoff interval. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpAdjWaitingTime specifies the time for which the entity has been waiting in backoff state. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpAdjBackoffStatus indicates whether or not the entity is in backoff state. If this value is 'true', then the entity is in a backoff state and if the value is 'false' then the entity is not in a backoff state. This object was obsoleted in release 13.0.

OBJECT-TYPE

vRtrLdpPeerParamsTable has an entry for an LDP peer. This table is used to configure parameters specific to the peer whether it is an interface or a targeted peer. In 13.0 this table has been replaced by TIMETRA-LDP-NG-MIB::vRtrLdpNgSessionParamsTable, TIMETRA-LDP-NG-MIB::vRtrLdpNgTcpSessParamsTable.

OBJECT-TYPE

Each row entry represents a peer that participates in the LDP protocol on this virtual router. Row entries can be created or deleted via SNMP SET requests. A row with default attribute values is created by setting vRtrLdpPeerRowStatus to 'createAndGo'. A row entry can be destroyed by setting vRtrLdpPeerRowStatus to 'destroy'. A row entry with vRtrLdpPeerAddress of 0.0.0.0 represents the default LDP parameters used for all peers that do not have a corresponding entry in this table.

OBJECT-TYPE

vRtrLdpPeerRowStatus is used to control the creation and deletion of rows in the vRtrLdpPeerParamsTable. A row can be created by setting vRtrLdpPeerRowStatus to 'createAndGo'. The agent should assign the default attribute values and change the row status to 'active'. A row entry can be destroyed by setting vRtrLdpPeerRowStatus to 'destroy'. This object was obsoleted in release 13.0.

OBJECT-TYPE

When the value of vRtrLdpPeerAuth is 'true', authentication using MD5 message based digest protocol is enabled. When 'false', no authentication is used. This object was obsoleted in release 13.0.

OBJECT-TYPE

The string specified in vRtrLdpPeerAuthKey is the authentication key to be used between LDP neighbors before establishing sessions. Authentication is done using the MD-5 message based digest protocol. The authentication key can be any combination of letters or numbers. Note that the string may contain embedded nulls. An SNMP Get request on this object should return an OCTET STRING of length 0. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpPeerMinTTLValue specifies the minimum TTL value for an incoming LDP packet. If vRtrLdpPeerMinTTLValue is set to zero (0), the TTL Security feature is disabled. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpPeerTTLLogId specifies the filter log to use for packets that fail TTL security check. The value zero indicates that logging is disabled. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpPeerAuthKeyChain specifies the keychain which will be used to sign and/or authenticate the LDP protocol stream. The keychain name is defined by tmnxKeyChainName and is the index for TIMETRA-SECURITY-MIB::tmnxKeyChainTable. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpPeerDODLabelDistribution specifies whether or not Downstream-On-Demand (DOD) has been enabled for the LDP session. When the value is set to 'true' DOD is enabled for the LDP session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpPeerImportPolicy1 specifies the first import policy used to determine which FEC prefixes received from other LDP and TLDP peers should be redistributed to this LDP peer. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpPeerImportPolicy2 specifies the second import policy used to determine which FEC prefixes received from other LDP and TLDP peers should be redistributed to this LDP peer. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpPeerImportPolicy3 specifies the third import policy used to determine which FEC prefixes received from other LDP and TLDP peers should be redistributed to this LDP peer. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpPeerImportPolicy4 specifies the fourth import policy used to determine which FEC prefixes received from other LDP and TLDP peers should be redistributed to this LDP peer. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpPeerImportPolicy5 specifies the fifth import policy used to determine which FEC prefixes received from other LDP and TLDP peers should be redistributed to this LDP peer. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpPeerExportPolicy1 specifies the first export policy used to determine which FEC prefixes received from this LDP peer should be redistributed to other LDP and TLDP peers. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpPeerExportPolicy2 specifies the second export policy used to determine which FEC prefixes received from this LDP peer should be redistributed to other LDP and TLDP peers. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpPeerExportPolicy3 specifies the third export policy used to determine which FEC prefixes received from this LDP peer should be redistributed to other LDP and TLDP peers. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpPeerExportPolicy4 specifies the fourth export policy used to determine which FEC prefixes received from this LDP peer should be redistributed to other LDP and TLDP peers. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpPeerExportPolicy5 specifies the fifth export policy used to determine which FEC prefixes received from this LDP peer should be redistributed to other LDP and TLDP peers. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpPeerFec129CiscoInterop specifies whether LDP will provide translation between non-compliant FEC 129 formats of Cisco. Peer LDP sessions must be manually configured towards the non-compliant Cisco PEs. When the value of vRtrLdpPeerFec129CiscoInterop is 'true', Cisco non-compliant format will be used to send and interpret received Label Release messages i.e. the FEC129 SAII and TAII fields will be reversed. When the value of vRtrLdpPeerFec129CiscoInterop is 'false', Cisco non-compliant format will not be used or supported. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpPeerPMTUDiscovery specifies whether path MTU discovery is enabled for this LDP peer. When the value is set to 'true', path MTU discovery is enabled for this LDP peer. When the value is set to 'false', path MTU discovery is disabled. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpPeerAdvAdjAddrOnly specifies whether to only distribute the local addresses used by hello adjacencies with this LDP peer. When the value is SET to 'true', local addresses that are used by hello adjacencies with this LDP peer are only distributed to the peer session . When the value is SET to 'false', all known local addresses are distributed to the peer session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpPeerPeIDMacFlushInterop specifies whether LDP will react to and send the non-standard PE-ID TLV (type 0x405) in an address withdraw message to effect 'flush-all-from-me' behavior. It is used to provide interoperability with other vendors that use this TLV for the MAC flush mechanism. Only FEC type 128 is currently supported. Peer LDP sessions must be manually configured towards the PEs requiring support for this TLV. When the value of vRtrLdpPeerPeIDMacFlushInterop is set to 'true', the receipt of an address withdraw message with empty MAC list including the non-standard TLV will trigger 'flush-all-from-me' behavior instead of the normal 'flush-all-but-mine'. The TLV will be included in any forwarding towards like-configured peers. When the value of vRtrLdpPeerPeIDMacFlushInterop is set to 'false', the non-standard TLV will be ignored and will not be included in any address withdraw messages sent to the peer. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpPeerMaxFec specifies the maximum number of FECs that will be accepted from this peer LSR. A value of zero specifies there is no limit to the number of FECs accepted from this peer LSR. The vRtrLdpSessMaxFecThresChanged notification is sent when the number of FECs receive from this peer LSR exceeds a percentage of this limit as specified by vRtrLdpPeerMaxFecThreshold. Furthermore, once the limit is exhausted, following actions are taken if vRtrLdpPeerMaxFecLogOnly has value of 'false'. (1) If LSR Overload capability is supported, this LSR will follow the LSR Overload procedure. (2) If LSR Overload capability is not supported, any further Label Mapping Message is returned with Label Release Message with LDP status code 'No_Label_Resources'. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpPeerMaxFecLogOnly specifies whether to only generate vRtrLdpSessMaxFecThresChanged notification or take further action when FECs received exceeds vRtrLdpPeerMaxFec limit. When this value is set to 'false', trap will be generated and one of the following action is taken: (1) If LSR Overload capability is supported, this LSR will follow the LSR Overload procedure. (2) If LSR Overload capability is not supported, any further Label Mapping Message is returned with Label Release Message with LDP status code 'No_Label_Resources'. When this value is set to 'true', trap will be generated only. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpPeerMaxFecThreshold specifies a percentage of vRtrLdpPeerMaxFec. This object was obsoleted in release 13.0.

OBJECT-IDENTITY

OBJECT-TYPE

Used by vRtrLdpInstanceStateChange, the value indicates the reason for the LDP instance state change.

OBJECT-TYPE

Used by vRtrLdpIfStateChange, the value indicates the reason for the LSP interface state change. This object was obsoleted in 7.0 as it is replaced by vRtrLdpIfOperDownReason in vRtrLdpIfStateChange.

OBJECT-TYPE

Used by vRtrLdpSvcIdMismatch, the value indicates the local Service ID.

OBJECT-TYPE

Used by vRtrLdpSvcIdMismatch, the value indicates the remote Service ID.

OBJECT-TYPE

Used by vRtrLdpGroupIdMismatch, the value indicates the local Group ID.

OBJECT-TYPE

Used by vRtrLdpGroupIdMismatch, the value indicates the remote Group ID.

OBJECT-TYPE

The value of vRtrLdpSessOverloadState indicates if session is overload or not. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessOverloadDirection indicates if Overload Notification is sent to peer or received from peer. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessOverloadFecType indicates the overloaded FEC type.

OBJECT-TYPE

The value of vRtrLdpSessOperThresLevel indicates whether the number of fec-bindings has exceeded or is below the configured fec threshold or has reached the configured fec limit.

OBJECT-TYPE

vRtrLdpStaticFecTable has an entry for each static prefix FEC configured on the virtual router. In 13.0 this table has been replaced by TIMETRA-LDP-NG-MIB::vRtrLdpNgStaticFecTable, TIMETRA-LDP-NG-MIB::vRtrLdpNgStaticFecInLabelTable.

OBJECT-TYPE

Each row entry represents a static prefix FEC configured on the virtual router. Entries can be created and deleted via SNMP SET operations to vRtrLdpStaticFecRowStatus. An entry is created by setting vRtrLdpStaticFecRowStatus to 'createAndWait'. The row status can be set to 'active' only after a next-hop entry corresponding to this prefix has been created in the vRtrLdpStaticFecNHTable. An entry is deleted by setting vRtrLdpStaticFecRowStatus to 'destroy'. For deletion to succeed, there must be no next-hop entries corresponding to this prefix in the vRtrLdpStaticFecNHTable i.e. vRtrLdpStaticFecNumNH must have a value of 0.

OBJECT-TYPE

The value of vRtrLdpStaticFecIpPrefix specifies the IP Address Prefix for this static FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpStaticFecIpMask specifies the IP Address Mask for this static FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

vRtrLdpStaticFecRowStatus is used to create, delete or control entries in the vRtrLdpStaticFecTable. To create a row entry, set vRtrLdpStaticFecRowStatus to 'createAndWait'. Before the row can be placed in the 'active' state, a next-hop entry corresponding to this prefix must exist in the vRtrLdpStaticFecNHTable. To delete a row entry, set vRtrLdpStaticFecRowStatus to 'destroy'. For deletion to succeed, no next-hop entry corresponding to this prefix must exist in the vRtrLdpStaticFecNHTable i.e. vRtrLdpStaticFecNumNH must have a value of 0. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpStaticFecNextNHIndex is used to assign values to vRtrLdpStaticFecNHIndex when creating rows in the vRtrLdpStaticFecNHTable. The network manager reads this object and uses it in the SET request that creates a new row entry in the vRtrLdpStaticFecNHTable. If the SET fails with the code 'inconsistentValue', the process must be repeated. If the SET succeeds, then this object will be incremented and the new instance is created according to the manager's directions. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpStaticFecIngLabel specifies the label that is advertised to the upstream peer. The range of vRtrLdpStaticFecIngLabel is dynamic and depends on the value of vRtrMplsLabelStaticLabelRange. The normal range of vRtrLdpStaticFecIngLabel starts at 32 and ends at the value of vRtrMplsLabelStaticLabelRange + 32. If this variable is set to the default value of 4294967295, the ingress label will be dynamically assigned by the label manager. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpStaticFecNumNH specifies the number of next-hops that are associated with the static prefix FEC represented by this row entry. This is also the number of row entries configured in the vRtrLdpStaticFecNHTable for this static prefix FEC. If the static FEC has no next-hops associated with it, this value will be 0 and the row entry will be placed in the 'notReady' state. Deletion of the row entry will be allowed only if vRtrLdpStaticFecNumNH is 0. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpStaticFecOperIngLabel specifies the actual or operational value of the label that was advertised to the upstream peer. This object was obsoleted in release 13.0.

OBJECT-TYPE

vRtrLdpStaticFecNHTable has an entry for each next-hop configured for a static prefix FEC on the virtual router. In 13.0 this table has been replaced by TIMETRA-LDP-NG-MIB::vRtrLdpNgStaticFecOutLabelTable.

OBJECT-TYPE

Each row entry represents a next-hop configured for a static prefix FEC on the virtual router. The static prefix FEC corresponding to a next-hop entry must exist as a row entry in the vRtrLdpStaticFecTable. Entries can be created and deleted via SNMP SET operations to vRtrLdpStaticFecNHRowStatus. An entry is created by setting vRtrLdpStaticFecNHRowStatus to 'createAndWait' or 'createAndGo'. Before the row can be placed in the 'active' state, vRtrLdpStaticFecNHType must be set to a valid value. An entry is deleted by setting vRtrLdpStaticFecNHRowStatus to 'destroy'.

OBJECT-TYPE

The value of vRtrLdpStaticFecNHIndex is used to identify the next-hop associated with a static prefix FEC. This value is unique amongst next-hop entries for the same static prefix FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

vRtrLdpStaticFecNHRowStatus is used to create, delete or control entries in the vRtrLdpStaticFecNHTable. An entry is created by setting vRtrLdpStaticFecNHRowStatus to 'createAndWait' or 'createAndGo'. Before the row can be placed in the 'active' state, vRtrLdpStaticFecNHType must be set to a valid value. An entry is deleted by setting vRtrLdpStaticFecNHRowStatus to 'destroy'. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpStaticFecNHType specifies the type of next-hop represented by this row entry. unknown (0) - the next-hop type has not been set. ipAddress (1) - the next-hop is an IP address. pop (2) - there is no next-hop i.e. pop the label and route ifName (3) - the next-hop is of this ifName ifNameAndIpAddress (4) - the next-hop is an IP address of this ifName This object was obsoleted in release 13.0.

OBJECT-TYPE

If vRtrLdpStaticFecNHType is set to 'ipAddress' or 'ifNameAndIpAddress', the value of vRtrLdpStaticFecNHIpAddr specifies the IP address of the next-hop. In this case, this variable must be set to a valid value before the row be placed in an active state. If vRtrLdpStaticFecNHType is set to 'pop', this value of vRtrLdpStaticFecNHIpAddr will be 0.0.0.0 This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpStaticFecNHEgrLabel specifies the egress label associated with this next-hop entry. The LSR will swap the incoming label with the configured egress label. If this egress label has a value of 4294967295, the LSR will pop the incoming label. This object was obsoleted in release 13.0.

OBJECT-TYPE

If vRtrLdpStaticFecNHType is set to 'ifName' or 'ifNameAndIpAddress', the value of vRtrLdpStaticFecNHIfName specifies the interface name to use for this static fec prefix. If vRtrLdpStaticFecNHType is set to 'pop', this value of vRtrLdpStaticFecNHIfName will be a null string. This object was obsoleted in release 13.0.

OBJECT-TYPE

vRtrLdpTargTable keeps information about the export and import prefixes for a targeted LDP session. Use of AUGMENTS clause implies a one-to-one dependent relationship between the base table, vRtrLdpGeneralTable, and the augmenting table, vRtrLdpTargTable. This in effect extends the vRtrLdpGeneralTable with additional columns. Creation or deletion of a row in the vRtrLdpGeneralTable results in the same fate for the row in the vRtrLdpTargTable. In 13.0 this table has been replaced by TIMETRA-LDP-NG-MIB::vRtrLdpNgTargTable.

OBJECT-TYPE

A row in this table represents information about the targeted LDP session.

OBJECT-TYPE

The value of vRtrLdpTargImportPolicy1 specifies the import route policy to determine which routes are accepted from targeted LDP neighbors. A maximum of 5 policies can be specified. vRtrLdpTargImportPolicy1 specifies the first policy. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpTargImportPolicy2 specifies the second import policy used to determine which routes are accepted from targeted LDP neighbors. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpTargImportPolicy3 specifies the third import policy used to determine which routes are accepted from targeted LDP neighbors. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpTargImportPolicy4 specifies the fourth import policy to determine which routes are accepted from targeted LDP neighbors. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpTargImportPolicy5 specifies the fifth import policy used to determine which routes are accepted from targeted LDP neighbors. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpTargExportPolicy1 specifies the export route policy used to determine which routes are exported to this targeted LDP session. A maximum of 5 policies can be specified. vRtrLdpTargExportPolicy1 specifies the first policy. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpTargExportPolicy2 specifies the second export policy used to determine which routes are exported to this targeted LDP session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpTargExportPolicy3 specifies the third export policy used to determine which routes are exported to this targeted LDP session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpTargExportPolicy4 specifies the fourth export policy used to determine which routes are exported to this targeted LDP session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpTargExportPolicy5 specifies the fifth export policy used to determine which routes are exported to this targeted LDP session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpTargTunnelPreference indicates whether LDP over tunnel is preferred when link-level LDP bindings are also available. If this value is 'true', then LDP tunnels are preferred and if the value is 'false' then LDP over tunnel is preferred. By default LDP tunnels are preferred. This object was obsoleted in release 13.0.

OBJECT-TYPE

vRtrLdpIfTunnelingLspTable keeps the list of LDP-over-RSVP LSP ids which are currently supported by the application. Each LSP ID in the list corresponds to the vRtrMplsLspIndex of the given MPLS LSP. In 13.0 this table has been replaced by TIMETRA-LDP-NG-MIB::vRtrLdpNgTargPeerTunnelLspTable.

OBJECT-TYPE

A row in this table contains the LSP id information about an LDP interface or targeted peer. Row entries can be created or deleted via SNMP SET requests. A row is created by setting vRtrLdpIfLspRowStatus to 'createAndGo' provided the corresponding LSP id exists as an MPLS lsp. A row entry can be destroyed by setting vRtrLdpIfLspRowStatus to 'destroy'.

OBJECT-TYPE

The value of vRtrLdpIfLspId specifies the LSP id of the LSP associated with the specified interface or targeted peer. This object was obsoleted in release 13.0.

OBJECT-TYPE

vRtrLdpIfLspRowStatus is used to create, delete or control entries in the vRtrLdpIfTunnelingLspTable. An entry is created by setting vRtrLdpIfLspRowStatus to 'createAndGo'. An entry is deleted by setting vRtrLdpIfLspRowStatus to 'destroy'. This object was obsoleted in release 13.0.

OBJECT-TYPE

vRtrLdpCepTdmFecTable is a read-only table that represents all CEP/TDM FECs either sent to or received from an LDP peer known to the Virtual Router. The CEP/TDM Sub-TLVs are defined in RFC 4446: Parameter Id Description 0x04 CEP/TDM Payload Bytes 0x07 CEP/TDM bit-rate 0x0B TDM Options In 13.0 this table has been replaced by TIMETRA-LDP-NG-MIB::vLdpNgCepTdmFec128InLblTable, TIMETRA-LDP-NG-MIB::vLdpNgCepTdmFec129InLblTable.

OBJECT-TYPE

Each row entry represents an instance of a service FEC sent to or received from an LDP peer. Use of AUGMENTS clause implies a one-to-one dependent relationship between the base table, vRtrLdpServFecTable, and the augmenting table, vRtrLdpCepTdmFecTable. This in effect extends the vRtrLdpServFecTable with additional columns. Creation or deletion of a row in the vRtrLdpServFecTable results in the same fate for the row in the VRtrLdpCepTdmFecEntry.

OBJECT-TYPE

The value of vRtrLdpCepTdmLocalPayloadSize indicates the local payload size. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpCepTdmRemotePayloadSize indicates the remote payload size. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpCepTdmLocalBitrate indicates the local bitrate. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpCepTdmRemoteBitrate indicates the remote bitrate. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpCepTdmLocalRtpHeader indicates the local RTP header usage bit. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpCepTdmRemoteRtpHeader indicates the remote RTP header usage bit. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpCepTdmLocalDiffTimestamp indicates the local differential (or dynamic) timestamping mode bit. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpCepTdmRemoteDiffTimestamp indicates the remote differential (or dynamic) timestamping mode bit. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpCepTdmLocalSigPkts indicates the local CE application signalling packets mode. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpCepTdmRemoteSigPkts indicates the remote CE application signalling packets mode. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpCepTdmLocalCasTrunk indicates the local CE application signalling packets mode. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpCepTdmRemoteCasTrunk indicates the remote CE application signalling packets mode. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpCepTdmLocalTimestampFreq indicates the local CE application signalling packets mode. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpCepTdmRemoteTimestampFreq indicates the remote CE application signalling packets mode. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpCepTdmLocalPayloadType indicates the local payload type. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpCepTdmRemotePayloadType indicates the remote payload type. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpCepTdmLocalSsrcId indicates the local value of SSRC ID. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpCepTdmRemoteSsrcId indicates the remote value of SSRC ID. This object was obsoleted in release 13.0.

OBJECT-TYPE

vLdpServFec129Table is a read-only table that represents all service FEC-129s either sent to or received from an LDP peer known to the Virtual Router. In 13.0 this table has been replaced by TIMETRA-LDP-NG-MIB::vLdpNgSvcFec129Table, TIMETRA-LDP-NG-MIB::vLdpNgSvcFec129InLblTable, TIMETRA-LDP-NG-MIB::vLdpNgSvcFec129OutLblTable.

OBJECT-TYPE

Each row entry represents an instance of a service FEC-129 sent to or received from an LDP peer.

OBJECT-TYPE

The value of vLdpServFec129AgiTlv specifies the Attachment Group Identifier TLV associated with this service FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpServFec129SrcAiiTlv specifies the Source Attachment Individual Identifier TLV associated with this service FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpServFec129TgtAiiTlv specifies the Target Attachment Individual Identifier TLV associated with this service FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpServFec129ServType specifies the Service type associated with this service FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpServFec129ServId specifies the Service identifier associated with this service FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpServFec129VpnId identifies the VPN associated with the FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

The bit flags of vLdpServFec129Flags specify the characteristics of the FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpServFec129NumInLabels gives the number of labels that have been sent to the peer associated with this FEC. This value also indicates whether vLdpServFec129InLabel1 entry contain valid information i.e. if the value of vLdpServFec129NumInLabels is 1 then vLdpServFec129InLabel1 will contain valid label information. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpServFec129NumOutLabels gives the number of labels that have been received from the peer associated with this FEC. This value also indicates whether vLdpServFec129OutLabel1 entry contain valid information i.e. if the value of vLdpServFec129NumOutLabels is 1, then vLdpServFec129OutLabel1 will contain valid label information. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpServFec129InLabel1 specifies the first ingress label exchanged. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpServFec129InLabelStatus1 specifies the status of the ingress label 1. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpServFec129OutLabel1 specifies the first egress label exchanged. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpServFec129OutLabelStatus1 specifies the status of the egress label 1. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpServFec129SdpId identifies the SDP associated with this peer. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpServFec129LocalMTU specifies the largest service frame size (in octets) that can be handled by the local ESR. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpServFec129RemoteMTU specifies the largest service frame size (in octets) that can be handled by the remote ESR. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpServFec129LocalVlanTag specifies the local tag on a VLAN VC type SDP binding. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpServFec129RemoteVlanTag specifies the remote tag on a VLAN VC type SDP binding. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpServFec129LocalMaxCellConcat specifies the local maximum number of ATM cells to concatenate on a ATM cell-mode VC type SDP binding. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpServFec129RemoteMaxCellConcat specifies the remote maximum number of ATM cells to concatenate on a ATM cell-mode VC type SDP binding. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpServFec129InLabelSigStatus1 indicates the signaling status for vLdpServFec129InLabel1. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpServFec129OutLabelSigStatus1 indicates the signaling status for vLdpServFec129OutLabel1. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpServFec129LocalIpv4Capblty indicates whether or not the local ipv4 stack capability is supported for this LDP peer. The value of vLdpServFec129LocalIpv4Capblty is 'true' when the local ipv4 stack capability is supported and the value is 'false' when the local ipv4 stack capability is not supported. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpServFec129RemoteIpv4Capblty indicates whether or not the remote ipv4 stack capability is supported for this LDP peer. The value of vLdpServFec129RemoteIpv4Capblty is 'true' when the remote ipv4 stack capability is supported and the value is 'false' when the remote ipv4 stack capability is not supported. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpServFec129LocalIpv6Capblty indicates whether or not the local ipv6 stack capability is supported for this LDP peer. The value of vLdpServFec129LocalIpv6Capblty is 'true' when the local ipv6 stack capability is supported and the value is 'false' when the local ipv6 stack capability is not supported. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpServFec129RemoteIpv6Capblty indicates whether or not the remote ipv6 stack capability is supported for this LDP peer. The value of vLdpServFec129RemoteIpv6Capblty is 'true' when the remote ipv6 stack capability is supported and the value is 'false' when the remote ipv6 stack capability is not supported. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpServFec129LocalIpv4CeIpAddr indicates the local ipv4 CE Address. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpServFec129RemoteIpv4CeIpAddr indicates the remote ipv4 CE Address. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpServFec129InLbl1WdwReason indicates the reason of withdrawal of ingress label value in vLdpServFec129InLabel1. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpServFec129LocalFLTxCapblty indicates whether or not this LDP peer is capable of sending Flow Label in its pseudowire (PW) packet. The value of vLdpServFec129LocalFLTxCapblty is 'true' when this LDP peer is capable of sending Flow Label and the value is 'false' when the peer is not capable of sending Flow Label in pseudowire packet. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpServFec129LocalFLRxCapblty indicates whether or not this LDP peer is capable of receiving Flow Label in its pseudowire packet. The value of vLdpServFec129LocalFLRxCapblty is 'true' when this LDP peer is capable of receiving Flow Label and the value is 'false' when the peer is not capable of receiving Flow Label in pseudowire packet. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpServFec129RemoteFLTxCapblty indicates whether or not the remote LDP peer is capable of sending Flow Label in its pseudowire packet. The value of vLdpServFec129RemoteFLTxCapblty is 'true' when the remote LDP peer is capable of sending Flow Label and the value is 'false' when the peer is not capable of sending Flow Label in pseudowire packet. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpServFec129RemoteFLRxCapblty indicates whether or not the remote LDP peer is capable of receiving Flow Label in its pseudowire packet. The value of vLdpServFec129RemoteFLRxCapblty is 'true' when the remote LDP peer is capable of receiving Flow Label and the value is 'false' when the peer is not capable of receiving Flow Label in pseudowire packet. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpServFec129MateAgiTlv identifies the Attachment Group Identifier TLV switched with this service FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpServFec129MateSrcAiiTlv identifies the Source Attachment Individual Identifier TLV switched with this service FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpServFec129MateTgtAiiTlv identifies the Target Attachment Individual Identifier TLV switched with this service FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpServFec129MateSdpId identifies the SDP switched with this peer. This object was obsoleted in release 13.0.

OBJECT-TYPE

vLdpServFec129MapTable is a read-only table which maps to the vLdpServFec129Table. This table has the same indexes as the vLdpServFec129Table but the order in which these indexes are specified is different for the two tables.

OBJECT-TYPE

Each row entry represents an instance of a service FEC sent to or received from an LDP peer.

OBJECT-TYPE

The value of vLdpServFec129MapVcType specifies the VC type associated with this service FEC.

OBJECT-TYPE

The value of vLdpServFec129MapAgiTlv specifies the Attachment Group Identifier TLV associated with this service FEC.

OBJECT-TYPE

The value of vLdpServFec129MapSrcAiiTlv specifies the Source Attachment Individual Identifier TLV associated with this service FEC.

OBJECT-TYPE

The value of vLdpServFec129MapTgtAiiTlv specifies the Target Attachment Individual Identifier TLV associated with this service FEC.

OBJECT-TYPE

vLdpCepTdmFec129Table is a read-only table that represents all CEP/TDM FECs either sent to or received from an LDP peer known to the Virtual Router. The CEP/TDM Sub-TLVs are defined in RFC 4446: Parameter Id Description 0x04 CEP/TDM Payload Bytes 0x07 CEP/TDM bit-rate 0x0B TDM Options In 13.0 this table has been replaced by TIMETRA-LDP-NG-MIB::vLdpNgCepTdmFec129InLblTable, TIMETRA-LDP-NG-MIB::vLdpNgCepTdmFec129OutLblTable.

OBJECT-TYPE

Each row entry represents an instance of a service FEC sent to or received from an LDP peer. Use of AUGMENTS clause implies a one-to-one dependent relationship between the base table, vRtrLdpServFecTable, and the augmenting table, vLdpCepTdmFec129Table. This in effect extends the vRtrLdpServFecTable with additional columns. Creation or deletion of a row in the vRtrLdpServFecTable results in the same fate for the row in the VLdpCepTdmFec129Entry.

OBJECT-TYPE

The value of vLdpCepTdmFec129LocalPayloadSize indicates the local payload size. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpCepTdmFec129RemotePayloadSize indicates the remote payload size. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpCepTdmFec129LocalBitrate indicates the local bitrate. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpCepTdmFec129RemoteBitrate indicates the remote bitrate. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpCepTdmFec129LocalRtpHeader indicates the local RTP header usage bit. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpCepTdmFec129RemoteRtpHeader indicates the remote RTP header usage bit. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpCepTdmFec129LocalDiffTimestamp indicates the local differential (or dynamic) timestamping mode bit. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpCepTdmFec129RemoteDiffTimestamp indicates the remote differential (or dynamic) timestamping mode bit. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpCepTdmFec129LocalSigPkts indicates the local CE application signalling packets mode. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpCepTdmFec129RemoteSigPkts indicates the remote CE application signalling packets mode. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpCepTdmFec129LocalCasTrunk indicates the local CE application signalling packets mode. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpCepTdmFec129RemoteCasTrunk indicates the remote CE application signalling packets mode. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpCepTdmFec129LocalTimestampFreq indicates the local CE application signalling packets mode. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpCepTdmFec129RemoteTimestampFreq indicates the remote CE application signalling packets mode. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpCepTdmFec129LocalPayloadType indicates the local payload type. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpCepTdmFec129RemotePayloadType indicates the remote payload type. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpCepTdmFec129LocalSsrcId indicates the local value of SSRC ID. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vLdpCepTdmFec129RemoteSsrcId indicates the remote value of SSRC ID. This object was obsoleted in release 13.0.

OBJECT-TYPE

vRtrLdpAggrPreMatchTable keeps information about aggregate prefix match procedures. Use of AUGMENTS clause implies a one-to-one dependent relationship between the base table, vRtrLdpGeneralTable, and the augmenting table, vRtrLdpAggrPreMatchTable. This in effect extends the vRtrLdpGeneralTable with additional columns. Creation or deletion of a row in the vRtrLdpGeneralTable results in the same fate for the row in the vRtrLdpAggrPreMatchTable. In 13.0 this table has been replaced by TIMETRA-LDP-NG-MIB::vRtrLdpNgAggrPreMatchTable.

OBJECT-TYPE

A row in this table represents information about the aggregate prefix match procedures.

OBJECT-TYPE

The value of vRtrLdpAggrPreMatchEnabled specifies whether aggregate prefix match procedures are enabled. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpAggrPreMatchPreExcPolicy1 specifies the policy name containing the prefixes to be excluded from the aggregate prefix match procedures. A maximum of 5 policies can be specified. vRtrLdpAggrPreMatchPreExcPolicy1 specifies the first policy. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpAggrPreMatchPreExcPolicy2 specifies the second policy name containing the prefixes to be excluded from the aggregate prefix match procedures. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpAggrPreMatchPreExcPolicy3 specifies the third policy name containing the prefixes to be excluded from the aggregate prefix match procedures. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpAggrPreMatchPreExcPolicy4 specifies the fourth policy name containing the prefixes to be excluded from the aggregate prefix match procedures. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpAggrPreMatchPreExcPolicy5 specifies the fifth policy name containing the prefixes to be excluded from the aggregate prefix match procedures. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpAggrPreMatchAdminState specifies whether the aggregate prefix procedures will be used by LDP. This object was obsoleted in release 13.0.

OBJECT-TYPE

Timestamp of the last change to the vRtrLdpEgrStatFecPfxTable either from adding a row or removing a row.

OBJECT-TYPE

vRtrLdpEgrStatFecPfxTable controls statistics in the egress data path at the ingress Label Switched Path (LSP) for an LDP FEC.

OBJECT-TYPE

A row in this table represents information about the statistics collection per FEC prefix.

OBJECT-TYPE

The IP address type of vRtrLdpEgrStatFecPfxAddr.

OBJECT-TYPE

The index value vRtrLdpEgrStatFecPfxAddr identifies the IP prefix for the LDP FEC.

OBJECT-TYPE

The index value vRtrLdpEgrStatFecPfxMaskLen identifies the prefix mask length of vRtrLdpEgrStatFecPfxAddr.

OBJECT-TYPE

vRtrLdpEgrStatFecPfxRowStatus is used for the creation or deletion of entries in the vRtrLdpEgrStatFecPfxTable.

OBJECT-TYPE

The value of vRtrLdpEgrStatFecPfxLastChgd indicates the time stamp of the last change to this row of this table.

OBJECT-TYPE

The value of vRtrLdpEgrStatFecPfxCollStats specifies whether to collect statistics for this prefix.

OBJECT-TYPE

The value of vRtrLdpEgrStatFecPfxActgPol specifies the accounting policy to be used for this prefix. A value of zero indicates that the default accounting policy should be used.

OBJECT-TYPE

The value of vRtrLdpEgrStatFecPfxAdminState specifies whether egress statistics are enabled for this prefix.

OBJECT-TYPE

The vRtrLdpEgrStatisticsTable has an entry for each Labeled Switch Path (LSP) configured for a virtual router in the system.

OBJECT-TYPE

Each row entry represents a collection of statistics for a Labeled Switch Path (LSP) configured for a virtual router in the system. Entries cannot be created and deleted via SNMP SET operations.

OBJECT-TYPE

The value of vRtrLdpInProfilePktsFc0 indicates the number of in profile packets received for Forwarding Class 0.

OBJECT-TYPE

The value of vRtrLdpInProfilePktsFc0Low32 indicates the lower 32 bits of the value of vRtrLdpInProfilePktsFc0.

OBJECT-TYPE

The value of vRtrLdpInProfilePktsFc0High32 indicates the higher 32 bits of the value of vRtrLdpInProfilePktsFc0.

OBJECT-TYPE

The value of vRtrLdpInProfilePktsFc1 indicates the number of in profile packets received for Forwarding Class 1.

OBJECT-TYPE

The value of vRtrLdpInProfilePktsFc1Low32 indicates the lower 32 bits of the value of vRtrLdpInProfilePktsFc1.

OBJECT-TYPE

The value of vRtrLdpInProfilePktsFc1High32 indicates the higher 32 bits of the value of vRtrLdpInProfilePktsFc1.

OBJECT-TYPE

The value of vRtrLdpInProfilePktsFc2 indicates the number of in profile packets received for Forwarding Class 2.

OBJECT-TYPE

The value of vRtrLdpInProfilePktsFc2Low32 indicates the lower 32 bits of the value of vRtrLdpInProfilePktsFc2.

OBJECT-TYPE

The value of vRtrLdpInProfilePktsFc2High32 indicates the higher 32 bits of the value of vRtrLdpInProfilePktsFc2.

OBJECT-TYPE

The value of vRtrLdpInProfilePktsFc3 indicates the number of in profile packets received for Forwarding Class 3.

OBJECT-TYPE

The value of vRtrLdpInProfilePktsFc3Low32 indicates the lower 32 bits of the value of vRtrLdpInProfilePktsFc3.

OBJECT-TYPE

The value of vRtrLdpInProfilePktsFc3High32 indicates the higher 32 bits of the value of vRtrLdpInProfilePktsFc3.

OBJECT-TYPE

The value of vRtrLdpInProfilePktsFc4 indicates the number of in profile packets received for Forwarding Class 4.

OBJECT-TYPE

The value of vRtrLdpInProfilePktsFc4Low32 indicates the lower 32 bits of the value of vRtrLdpInProfilePktsFc4.

OBJECT-TYPE

The value of vRtrLdpInProfilePktsFc4High32 indicates the higher 32 bits of the value of vRtrLdpInProfilePktsFc4.

OBJECT-TYPE

The value of vRtrLdpInProfilePktsFc5 indicates the number of in profile packets received for Forwarding Class 5.

OBJECT-TYPE

The value of vRtrLdpInProfilePktsFc5Low32 indicates the lower 32 bits of the value of vRtrLdpInProfilePktsFc5.

OBJECT-TYPE

The value of vRtrLdpInProfilePktsFc5High32 indicates the higher 32 bits of the value of vRtrLdpInProfilePktsFc5.

OBJECT-TYPE

The value of vRtrLdpInProfilePktsFc6 indicates the number of in profile packets received for Forwarding Class 6.

OBJECT-TYPE

The value of vRtrLdpInProfilePktsFc6Low32 indicates the lower 32 bits of the value of vRtrLdpInProfilePktsFc6.

OBJECT-TYPE

The value of vRtrLdpInProfilePktsFc6High32 indicates the higher 32 bits of the value of vRtrLdpInProfilePktsFc6.

OBJECT-TYPE

The value of vRtrLdpInProfilePktsFc7 indicates the number of in profile packets received for Forwarding Class 7.

OBJECT-TYPE

The value of vRtrLdpInProfilePktsFc7Low32 indicates the lower 32 bits of the value of vRtrLdpInProfilePktsFc7.

OBJECT-TYPE

The value of vRtrLdpInProfilePktsFc7High32 indicates the higher 32 bits of the value of vRtrLdpInProfilePktsFc7.

OBJECT-TYPE

The value of vRtrLdpInProfileOctetsFc0 indicates the number of in profile octets received for Forwarding Class 0.

OBJECT-TYPE

The value of vRtrLdpInProfileOctetsFc0Low32 indicates the lower 32 bits of the value of vRtrLdpInProfileOctetsFc0.

OBJECT-TYPE

The value of vRtrLdpInProfileOctetsFc0High32 indicates the higher 32 bits of the value of vRtrLdpInProfileOctetsFc0.

OBJECT-TYPE

The value of vRtrLdpInProfileOctetsFc1 indicates the number of in profile octets received for Forwarding Class 1.

OBJECT-TYPE

The value of vRtrLdpInProfileOctetsFc1Low32 indicates the lower 32 bits of the value of vRtrLdpInProfileOctetsFc1.

OBJECT-TYPE

The value of vRtrLdpInProfileOctetsFc1High32 indicates the higher 32 bits of the value of vRtrLdpInProfileOctetsFc1.

OBJECT-TYPE

The value of vRtrLdpInProfileOctetsFc2 indicates the number of in profile octets received for Forwarding Class 2.

OBJECT-TYPE

The value of vRtrLdpInProfileOctetsFc2Low32 indicates the lower 32 bits of the value of vRtrLdpInProfileOctetsFc2.

OBJECT-TYPE

The value of vRtrLdpInProfileOctetsFc2High32 indicates the higher 32 bits of the value of vRtrLdpInProfileOctetsFc2.

OBJECT-TYPE

The value of vRtrLdpInProfileOctetsFc3 indicates the number of in profile octets received for Forwarding Class 3.

OBJECT-TYPE

The value of vRtrLdpInProfileOctetsFc3Low32 indicates the lower 32 bits of the value of vRtrLdpInProfileOctetsFc3.

OBJECT-TYPE

The value of vRtrLdpInProfileOctetsFc3High32 indicates the higher 32 bits of the value of vRtrLdpInProfileOctetsFc3.

OBJECT-TYPE

The value of vRtrLdpInProfileOctetsFc4 indicates the number of in profile octets received for Forwarding Class 4.

OBJECT-TYPE

The value of vRtrLdpInProfileOctetsFc4Low32 indicates the lower 32 bits of the value of vRtrLdpInProfileOctetsFc4.

OBJECT-TYPE

The value of vRtrLdpInProfileOctetsFc4High32 indicates the higher 32 bits of the value of vRtrLdpInProfileOctetsFc4.

OBJECT-TYPE

The value of vRtrLdpInProfileOctetsFc5 indicates the number of in profile octets received for Forwarding Class 5.

OBJECT-TYPE

The value of vRtrLdpInProfileOctetsFc5Low32 indicates the lower 32 bits of the value of vRtrLdpInProfileOctetsFc5.

OBJECT-TYPE

The value of vRtrLdpInProfileOctetsFc5High32 indicates the higher 32 bits of the value of vRtrLdpInProfileOctetsFc5.

OBJECT-TYPE

The value of vRtrLdpInProfileOctetsFc6 indicates the number of in profile octets received for Forwarding Class 6.

OBJECT-TYPE

The value of vRtrLdpInProfileOctetsFc6Low32 indicates the lower 32 bits of the value of vRtrLdpInProfileOctetsFc6.

OBJECT-TYPE

The value of vRtrLdpInProfileOctetsFc6High32 indicates the higher 32 bits of the value of vRtrLdpInProfileOctetsFc6.

OBJECT-TYPE

The value of vRtrLdpInProfileOctetsFc7 indicates the number of in profile octets received for Forwarding Class 7.

OBJECT-TYPE

The value of vRtrLdpInProfileOctetsFc7Low32 indicates the lower 32 bits of the value of vRtrLdpInProfileOctetsFc7.

OBJECT-TYPE

The value of vRtrLdpInProfileOctetsFc7High32 indicates the higher 32 bits of the value of vRtrLdpInProfileOctetsFc7.

OBJECT-TYPE

The value of vRtrLdpOutOfProfPktsFc0 indicates the number of out of profile packets received for Forwarding Class 0.

OBJECT-TYPE

The value of vRtrLdpOutOfProfPktsFc0Low32 indicates the lower 32 bits of the value of vRtrLdpOutOfProfPktsFc0.

OBJECT-TYPE

The value of vRtrLdpOutOfProfPktsFc0High32 indicates the higher 32 bits of the value of vRtrLdpOutOfProfPktsFc0.

OBJECT-TYPE

The value of vRtrLdpOutOfProfPktsFc1 indicates the number of out of profile packets received for Forwarding Class 1.

OBJECT-TYPE

The value of vRtrLdpOutOfProfPktsFc1Low32 indicates the lower 32 bits of the value of vRtrLdpOutOfProfPktsFc1.

OBJECT-TYPE

The value of vRtrLdpOutOfProfPktsFc1High32 indicates the higher 32 bits of the value of vRtrLdpOutOfProfPktsFc1.

OBJECT-TYPE

The value of vRtrLdpOutOfProfPktsFc2 indicates the number of out of profile packets received for Forwarding Class 2.

OBJECT-TYPE

The value of vRtrLdpOutOfProfPktsFc2Low32 indicates the lower 32 bits of the value of vRtrLdpOutOfProfPktsFc2.

OBJECT-TYPE

The value of vRtrLdpOutOfProfPktsFc2High32 indicates the higher 32 bits of the value of vRtrLdpOutOfProfPktsFc2.

OBJECT-TYPE

The value of vRtrLdpOutOfProfPktsFc3 indicates the number of out of profile packets received for Forwarding Class 3.

OBJECT-TYPE

The value of vRtrLdpOutOfProfPktsFc3Low32 indicates the lower 32 bits of the value of vRtrLdpOutOfProfPktsFc3.

OBJECT-TYPE

The value of vRtrLdpOutOfProfPktsFc3High32 indicates the higher 32 bits of the value of vRtrLdpOutOfProfPktsFc3.

OBJECT-TYPE

The value of vRtrLdpOutOfProfPktsFc4 indicates the number of out of profile packets received for Forwarding Class 4.

OBJECT-TYPE

The value of vRtrLdpOutOfProfPktsFc4Low32 indicates the lower 32 bits of the value of vRtrLdpOutOfProfPktsFc4.

OBJECT-TYPE

The value of vRtrLdpOutOfProfPktsFc4High32 indicates the higher 32 bits of the value of vRtrLdpOutOfProfPktsFc4.

OBJECT-TYPE

The value of vRtrLdpOutOfProfPktsFc5 indicates the number of out of profile packets received for Forwarding Class 5.

OBJECT-TYPE

The value of vRtrLdpOutOfProfPktsFc5Low32 indicates the lower 32 bits of the value of vRtrLdpOutOfProfPktsFc5.

OBJECT-TYPE

The value of vRtrLdpOutOfProfPktsFc5High32 indicates the higher 32 bits of the value of vRtrLdpOutOfProfPktsFc5.

OBJECT-TYPE

The value of vRtrLdpOutOfProfPktsFc6 indicates the number of out of profile packets received for Forwarding Class 6.

OBJECT-TYPE

The value of vRtrLdpOutOfProfPktsFc6Low32 indicates the lower 32 bits of the value of vRtrLdpOutOfProfPktsFc6.

OBJECT-TYPE

The value of vRtrLdpOutOfProfPktsFc6High32 indicates the higher 32 bits of the value of vRtrLdpOutOfProfPktsFc6.

OBJECT-TYPE

The value of vRtrLdpOutOfProfPktsFc7 indicates the number of out of profile packets received for Forwarding Class 7.

OBJECT-TYPE

The value of vRtrLdpOutOfProfPktsFc7Low32 indicates the lower 32 bits of the value of vRtrLdpOutOfProfPktsFc7.

OBJECT-TYPE

The value of vRtrLdpOutOfProfPktsFc7High32 indicates the higher 32 bits of the value of vRtrLdpOutOfProfPktsFc7.

OBJECT-TYPE

The value of vRtrLdpOutOfProfOctetsFc0 indicates the number of out of profile octets received for Forwarding Class 0.

OBJECT-TYPE

The value of vRtrLdpOutOfProfOctetsFc0Low32 indicates the lower 32 bits of the value of vRtrLdpOutOfProfOctetsFc0.

OBJECT-TYPE

The value of vRtrLdpOutOfProfOctetsFc0High32 indicates the higher 32 bits of the value of vRtrLdpOutOfProfOctetsFc0.

OBJECT-TYPE

The value of vRtrLdpOutOfProfOctetsFc1 indicates the number of out of profile octets received for Forwarding Class 1.

OBJECT-TYPE

The value of vRtrLdpOutOfProfOctetsFc1Low32 indicates the lower 32 bits of the value of vRtrLdpOutOfProfOctetsFc1.

OBJECT-TYPE

The value of vRtrLdpOutOfProfOctetsFc1High32 indicates the higher 32 bits of the value of vRtrLdpOutOfProfOctetsFc1.

OBJECT-TYPE

The value of vRtrLdpOutOfProfOctetsFc2 indicates the number of out of profile octets received for Forwarding Class 2.

OBJECT-TYPE

The value of vRtrLdpOutOfProfOctetsFc2Low32 indicates the lower 32 bits of the value of vRtrLdpOutOfProfOctetsFc2.

OBJECT-TYPE

The value of vRtrLdpOutOfProfOctetsFc2High32 indicates the higher 32 bits of the value of vRtrLdpOutOfProfOctetsFc2.

OBJECT-TYPE

The value of vRtrLdpOutOfProfOctetsFc3 indicates the number of out of profile octets received for Forwarding Class 3.

OBJECT-TYPE

The value of vRtrLdpOutOfProfOctetsFc3Low32 indicates the lower 32 bits of the value of vRtrLdpOutOfProfOctetsFc3.

OBJECT-TYPE

The value of vRtrLdpOutOfProfOctetsFc3High32 indicates the higher 32 bits of the value of vRtrLdpOutOfProfOctetsFc3.

OBJECT-TYPE

The value of vRtrLdpOutOfProfOctetsFc4 indicates the number of out of profile octets received for Forwarding Class 4.

OBJECT-TYPE

The value of vRtrLdpOutOfProfOctetsFc4Low32 indicates the lower 32 bits of the value of vRtrLdpOutOfProfOctetsFc4.

OBJECT-TYPE

The value of vRtrLdpOutOfProfOctetsFc4High32 indicates the higher 32 bits of the value of vRtrLdpOutOfProfOctetsFc4.

OBJECT-TYPE

The value of vRtrLdpOutOfProfOctetsFc5 indicates the number of out of profile octets received for Forwarding Class 5.

OBJECT-TYPE

The value of vRtrLdpOutOfProfOctetsFc5Low32 indicates the lower 32 bits of the value of vRtrLdpOutOfProfOctetsFc5.

OBJECT-TYPE

The value of vRtrLdpOutOfProfOctetsFc5High32 indicates the higher 32 bits of the value of vRtrLdpOutOfProfOctetsFc5.

OBJECT-TYPE

The value of vRtrLdpOutOfProfOctetsFc6 indicates the number of out of profile octets received for Forwarding Class 6.

OBJECT-TYPE

The value of vRtrLdpOutOfProfOctetsFc6Low32 indicates the lower 32 bits of the value of vRtrLdpOutOfProfOctetsFc6.

OBJECT-TYPE

The value of vRtrLdpOutOfProfOctetsFc6High32 indicates the higher 32 bits of the value of vRtrLdpOutOfProfOctetsFc6.

OBJECT-TYPE

The value of vRtrLdpOutOfProfOctetsFc7 indicates the number of out of profile octets received for Forwarding Class 7.

OBJECT-TYPE

The value of vRtrLdpOutOfProfOctetsFc7Low32 indicates the lower 32 bits of the value of vRtrLdpOutOfProfOctetsFc7.

OBJECT-TYPE

The value of vRtrLdpOutOfProfOctetsFc7High32 indicates the higher 32 bits of the value of vRtrLdpOutOfProfOctetsFc7.

OBJECT-TYPE

The value of vRtrLdpAggregatePkts indicates the number of packets sent for the FEC.

OBJECT-TYPE

The value of vRtrLdpAggregatePktsLow32 indicates the lower 32 bits of the value of vRtrLdpAggregatePkts.

OBJECT-TYPE

The value of vRtrLdpAggregatePktsHigh32 indicates the higher 32 bits of the value of vRtrLdpAggregatePkts.

OBJECT-TYPE

The value of vRtrLdpAggregateOctets indicates the number of octets sent for the FEC.

OBJECT-TYPE

The value of vRtrLdpAggregateOctetsLow32 indicates the lower 32 bits of the value of vRtrLdpAggregateOctets.

OBJECT-TYPE

The value of vRtrLdpAggregateOctetsHigh32 indicates the higher 32 bits of the value of vRtrLdpAggregateOctets.

OBJECT-TYPE

The vRtrLdpAddrFecExtTable has an entry with few fields which are extensions for all address FECs either sent to or received from an LDP peer known to the Virtual Router.

OBJECT-TYPE

Each row entry represents an instance of an extension to address FEC sent to or received from an LDP peer. Entries cannot be created and deleted via SNMP SET operations.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLbl6 specifies the sixth egress label exchanged. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblStatus6 specifies the status of the egress label 6. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblIfIndex6 specifies the interface index for egress label 6. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblNxtHopType6 specifies the address type of vRtrLdpAddrFecOutLblNxtHopAddr6. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblNxtHopAddr6 specifies the IP address of the next hop for egress label 6. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecLspId6 indicates the LSP id of the LSP for the RSVP tunnel used by LDP in LDP over RSVP associated with egress label 6. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLbl7 specifies the seventh egress label exchanged. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblStatus7 specifies the status of the egress label 7. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblIfIndex7 specifies the interface index for egress label 7. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblNxtHopType7 specifies the address type of vRtrLdpAddrFecOutLblNxtHopAddr7. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblNxtHopAddr7 specifies the IP address of the next hop for egress label 7. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecLspId7 indicates the LSP id of the LSP for the RSVP tunnel used by LDP in LDP over RSVP associated with egress label 7. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLbl8 specifies the eighth egress label exchanged. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblStatus8 specifies the status of the egress label 8. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblIfIndex8 specifies the interface index for egress label 8. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblNxtHopType8 specifies the address type of vRtrLdpAddrFecOutLblNxtHopAddr8. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblNxtHopAddr8 specifies the IP address of the next hop for egress label 8. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecLspId8 indicates the LSP id of the LSP for the RSVP tunnel used by LDP in LDP over RSVP associated with egress label 8. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLbl9 specifies the ninth egress label exchanged. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblStatus9 specifies the status of the egress label 9. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblIfIndex9 specifies the interface index for egress label 9. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblNxtHopType9 specifies the address type of vRtrLdpAddrFecOutLblNxtHopAddr9. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblNxtHopAddr9 specifies the IP address of the next hop for egress label 9. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecLspId9 indicates the LSP id of the LSP for the RSVP tunnel used by LDP in LDP over RSVP associated with egress label 9. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLbl10 specifies the tenth egress label exchanged. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblStatus10 specifies the status of the egress label 10. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblIfIndex10 specifies the interface index for egress label 10. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblNxtHopType10 specifies the address type of vRtrLdpAddrFecOutLblNxtHopAddr10. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblNxtHopAddr10 specifies the IP address of the next hop for egress label 10. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecLspId10 indicates the LSP id of the LSP for the RSVP tunnel used by LDP in LDP over RSVP associated with egress label 10. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLbl11 specifies the eleventh egress label exchanged. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblStatus11 specifies the status of the egress label 11. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblIfIndex11 specifies the interface index for egress label 11. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblNxtHopType11 specifies the address type of vRtrLdpAddrFecOutLblNxtHopAddr11. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblNxtHopAddr11 specifies the IP address of the next hop for egress label 11. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecLspId11 indicates the LSP id of the LSP for the RSVP tunnel used by LDP in LDP over RSVP associated with egress label 11. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLbl12 specifies the twelfth egress label exchanged. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblStatus12 specifies the status of the egress label 12. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblIfIndex12 specifies the interface index for egress label 12. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblNxtHopType12 specifies the address type of vRtrLdpAddrFecOutLblNxtHopAddr12. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblNxtHopAddr12 specifies the IP address of the next hop for egress label 12. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecLspId12 indicates the LSP id of the LSP for the RSVP tunnel used by LDP in LDP over RSVP associated with egress label 12. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLbl13 specifies the thirteenth egress label exchanged. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblStatus13 specifies the status of the egress label 13. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblIfIndex13 specifies the interface index for egress label 13. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblNxtHopType13 specifies the address type of vRtrLdpAddrFecOutLblNxtHopAddr13. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblNxtHopAddr13 specifies the IP address of the next hop for egress label 13. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecLspId13 indicates the LSP id of the LSP for the RSVP tunnel used by LDP in LDP over RSVP associated with egress label 13. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLbl14 specifies the fourteenth egress label exchanged. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblStatus14 specifies the status of the egress label 14. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblIfIndex14 specifies the interface index for egress label 14. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblNxtHopType14 specifies the address type of vRtrLdpAddrFecOutLblNxtHopAddr14. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblNxtHopAddr14 specifies the IP address of the next hop for egress label 14. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecLspId14 indicates the LSP id of the LSP for the RSVP tunnel used by LDP in LDP over RSVP associated with egress label 14. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLbl15 specifies the fifteenth egress label exchanged. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblStatus15 specifies the status of the egress label 15. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblIfIndex15 specifies the interface index for egress label 15. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblNxtHopType15 specifies the address type of vRtrLdpAddrFecOutLblNxtHopAddr15. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblNxtHopAddr15 specifies the IP address of the next hop for egress label 15. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecLspId15 indicates the LSP id of the LSP for the RSVP tunnel used by LDP in LDP over RSVP associated with egress label 15. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLbl16 specifies the sixteenth egress label exchanged. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblStatus16 specifies the status of the egress label 16. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblIfIndex16 specifies the interface index for egress label 16. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblNxtHopType16 specifies the address type of vRtrLdpAddrFecOutLblNxtHopAddr16. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblNxtHopAddr16 specifies the IP address of the next hop for egress label 16. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecLspId16 indicates the LSP id of the LSP for the RSVP tunnel used by LDP in LDP over RSVP associated with egress label 16. This object was obsoleted in release 10.0.

OBJECT-TYPE

vRtrLdpP2MPFecTable is a read-only table that represents operational information of P2MP FECs either sent to or received from an LDP peer known to the Virtual Router.

OBJECT-TYPE

Each row entry represents an instance of operational information of a P2MP FEC sent to or received from an LDP peer.

OBJECT-TYPE

The value of vRtrLdpP2MPFecTunnelType indicates the tunnel type of P2MP FEC. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpP2MPFecTunnelId indicates the tunnel identifier for this P2MP FEC. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpP2MPFecRootAddrType indicates the type of ip address of the root for this P2MP FEC. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpP2MPFecRootAddress indicates the ip address of the root for this P2MP FEC. This object was obsoleted in release 10.0.

OBJECT-TYPE

The bit flags of vRtrLdpP2MPFecFlags indicates the characteristics of the FEC. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpP2MPFecNumInLabels indicates the number of labels that have been sent to the peer associated with this FEC. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpP2MPFecNumOutLabels indicates the number of labels that have been received from the peer associated with this FEC. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpP2MPFecTunnelIfId indicates the tunnel interface identifier for this P2MP FEC. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpP2MPFecMetric indicates the relative cost of the tunnel represented by this P2MP FEC. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpP2MPFecMTU indicates the maximum transfer unit for payloads represented by this P2MP FEC. This object was obsoleted in release 10.0.

OBJECT-TYPE

vRtrLdpP2MPFecInLabelTable is a read-only table that represents all P2MP FECs received from an LDP peer known to the virtual router.

OBJECT-TYPE

Each row entry represents an instance of a P2MP FEC received from an LDP peer.

OBJECT-TYPE

The value of vRtrLdpP2MPFecInLblId indicates the label number of the ingress label exchanged. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpP2MPFecInLbl indicates the ingress label exchanged. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpP2MPFecInLblStatus indicates the status of the ingress label. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpP2MPFecInLblIfIndex indicates the interface index for ingress label. This object was obsoleted in release 10.0.

OBJECT-TYPE

vRtrLdpP2MPFecTable is a read-only table that represents all P2MP FECs sent to an LDP peer known to the Virtual Router.

OBJECT-TYPE

Each row entry represents an instance of a P2MP FEC sent to a LDP peer.

OBJECT-TYPE

The value of vRtrLdpP2MPFecOutLblId indicates the label number of the egress label exchanged. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpP2MPFecOutLbl indicates the egress label exchanged. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpP2MPFecOutLblStatus indicates the status of the egress label. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpP2MPFecOutLblNxtHopType indicates the address type of vRtrLdpP2MPFecOutLblNxtHopAddr. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpP2MPFecOutLblNxtHopAddr indicates the IP address of the next hop for egress label. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpP2MPFecOutLblIfIndex indicates the interface index for egress label. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpP2MPFecOutLblLspId indicates the LSP id of the LSP for the RSVP tunnel used by LDP in LDP over RSVP associated with egress label. This object was obsoleted in release 10.0.

OBJECT-TYPE

vRtrLdpP2MPFecMapTable is a read-only table which maps to the vRtrLdpP2MPFecTable. This table has the same indexes as the vRtrLdpP2MPFecTable but the order in which these indexes are specified is different for the two tables.

OBJECT-TYPE

Each row entry represents an instance of a P2MP FEC sent to or received from an LDP peer.

OBJECT-TYPE

The value of vRtrLdpP2MPFecMapFecType indicates the tunnel type of P2MP FEC. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpP2MPFecMapId indicates the tunnel identifier for this P2MP FEC. This object was obsoleted in release 10.0.

OBJECT-TYPE

vRtrLdpAddrFecOutLblInfoTable is a read-only table that contains the information related to an egress label of an address FEC sent to or received from an LDP peer.

OBJECT-TYPE

Each row entry represents an instance of an egress label of an address FEC sent to or received from an LDP peer.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblId indicates the egress label exchanged. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblMetric indicates the relative cost of the tunnel represented by this address FEC egress label. This object was obsoleted in release 10.0.

OBJECT-TYPE

The value of vRtrLdpAddrFecOutLblMtu indicates the maximum transfer unit for payloads represented by this address FEC egress label. This object was obsoleted in release 10.0.

OBJECT-TYPE

vRtrLdpNgP2MPFecTable is a read-only table that represents operational information of P2MP FECs either sent to or received from an LDP peer known to the Virtual Router. In 13.0 this table has been replaced by TIMETRA-LDP-NG-MIB::vRtrLdpNgExtP2MPFecTable.

OBJECT-TYPE

Each row entry represents an instance of operational information of a P2MP FEC sent to or received from an LDP peer.

OBJECT-TYPE

The value of vRtrLdpNgP2MPFecOpaqueType indicates the type of a Multi-Point Opaque Value Element. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpNgP2MPFecOpaqueLength indicates the length of a Multi-Point Opaque Value Element. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpNgP2MPFecOpaqueValue indicates the value of a Multi-Point Opaque Value Element. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpNgP2MPFecRootAddrType indicates the type of ip address of the root for this P2MP FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpNgP2MPFecRootAddress indicates the ip address of the root for this P2MP FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

The bit flags of vRtrLdpNgP2MPFecFlags indicates the characteristics of the FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpNgP2MPFecNumInLabels indicates the number of labels that have been sent to the peer associated with this FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpNgP2MPFecNumOutLabels indicates the number of labels that have been received from the peer associated with this FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpNgP2MPFecTunnelIfId indicates the tunnel interface identifier for this P2MP FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpNgP2MPFecMetric indicates the relative cost of the tunnel represented by this P2MP FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpNgP2MPFecMTU indicates the maximum transfer unit for payloads represented by this P2MP FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

vRtrLdpNgP2MPFecInLabelTable is a read-only table that represents all P2MP FECs received from an LDP peer known to the virtual router. In 13.0 this table has been replaced by TIMETRA-LDP-NG-MIB::vRtrLdpNgExtP2MPFecInLblTable.

OBJECT-TYPE

Each row entry represents an instance of a P2MP FEC received from an LDP peer.

OBJECT-TYPE

The value of vRtrLdpNgP2MPFecInLblId indicates the label number of the ingress label exchanged. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpNgP2MPFecInLbl indicates the ingress label exchanged. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpNgP2MPFecInLblStatus indicates the status of the ingress label. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpNgP2MPFecInLblIfIndex indicates the interface index for ingress label. This object was obsoleted in release 13.0.

OBJECT-TYPE

vRtrLdpNgP2MPFecTable is a read-only table that represents all P2MP FECs sent to an LDP peer known to the Virtual Router. In 13.0 this table has been replaced by TIMETRA-LDP-NG-MIB::vRtrLdpNgExtP2MPFecOutLblTable.

OBJECT-TYPE

Each row entry represents an instance of a P2MP FEC sent to a LDP peer.

OBJECT-TYPE

The value of vRtrLdpNgP2MPFecOutLblId indicates the label number of the egress label exchanged. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpNgP2MPFecOutLbl indicates the egress label exchanged. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpNgP2MPFecOutLblStatus indicates the status of the egress label. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpNgP2MPFecOutLblNxtHopType indicates the address type of vRtrLdpNgP2MPFecOutLblNxtHopAddr. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpNgP2MPFecOutLblNxtHopAddr indicates the IP address of the next hop for egress label. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpNgP2MPFecOutLblIfIndex indicates the interface index for egress label. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpNgP2MPFecOutLblLspId indicates the LSP id of the LSP for the RSVP tunnel used by LDP in LDP over RSVP associated with egress label. This object was obsoleted in release 13.0.

OBJECT-TYPE

vRtrLdpNgP2MPFecMapTable is a read-only table which maps to the vRtrLdpNgP2MPFecTable. This table has the same indexes as the vRtrLdpNgP2MPFecTable but the order in which these indexes are specified is different for the two tables. In 13.0 this table has been replaced by TIMETRA-LDP-NG-MIB::vRtrLdpNgExtP2MPFecMapTable.

OBJECT-TYPE

Each row entry represents an instance of a P2MP FEC sent to or received from an LDP peer.

OBJECT-TYPE

The bit flags of vRtrLdpNgP2MPFecMapFlags indicates the characteristics of the FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpNgP2MPFecMapNumInLabels indicates the number of labels that have been sent to the peer associated with this FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpNgP2MPFecMapNumOutLabels indicates the number of labels that have been received from the peer associated with this FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpNgP2MPFecMapTunnelIfId indicates the tunnel interface identifier for this P2MP FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpNgP2MPFecMapMetric indicates the relative cost of the tunnel represented by this P2MP FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpNgP2MPFecMapMTU indicates the maximum transfer unit for payloads represented by this P2MP FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

vRtrLdpAddressFecTable is a read-only table that represents all address FECs either sent to or received from an LDP peer known to the Virtual Router. In 13.0 this table has been replaced by TIMETRA-LDP-NG-MIB::vRtrLdpNgAddrFecTable.

OBJECT-TYPE

Each row entry represents an instance of an address FEC sent to or received from an LDP peer.

OBJECT-TYPE

The value of vRtrLdpAddressFecFecType specifies the FEC type. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpAddressFecIpPrefixType indicates the address type of vRtrLdpAddressFecIpPrefix. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpAddressFecIpPrefix specifies the IP Address Prefix for this address FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpAddressFecIpPrefixLen indicates the prefix length of the subnet associated with vRtrLdpAddressFecIpPrefix. This object was obsoleted in release 13.0.

OBJECT-TYPE

The bit flags of vRtrLdpAddressFecFlags specify the characteristics of the FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpAddressFecNumInLabels gives the number of labels that have been sent to the peer associated with this FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpAddressFecNumOutLabels gives the number of labels that have been received from the peer associated with this FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

vRtrLdpAddressFecInLabelTable is a read-only table that represents all address FECs received from an LDP peer known to the Virtual Router. In 13.0 this table has been replaced by TIMETRA-LDP-NG-MIB::vRtrLdpNgAddrFecInLblTable.

OBJECT-TYPE

Each row entry represents an instance of an address FEC received from an LDP peer.

OBJECT-TYPE

The value of vRtrLdpAddressFecInLblId indicates the label number of the ingress label exchanged. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpAddressFecInLbl specifies the ingress label exchanged. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpAddressFecInLblStatus specifies the status of the ingress label. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpAddressFecInLblIfIndex specifies the interface index for ingress label. This object was obsoleted in release 13.0.

OBJECT-TYPE

vRtrLdpAddressFecOutLabelTable is a read-only table that represents all address FECs received from an LDP peer known to the Virtual Router. In 13.0 this table has been replaced by TIMETRA-LDP-NG-MIB::vRtrLdpNgAddrFecOutLblTable.

OBJECT-TYPE

Each row entry represents an instance of an address FEC received from an LDP peer.

OBJECT-TYPE

The value of vRtrLdpAddressFecOutLblId indicates the label number of the egress label exchanged. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpAddressFecOutLbl specifies the egress label exchanged. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpAddressFecOutLblStatus specifies the status of the egress label. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpAddressFecOutLblIfIndex specifies the interface index for egress label. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpAddressFecOutLblNHType specifies the address type of vRtrLdpAddressFecOutLblNHAddr. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpAddressFecOutLblNHAddr specifies the IP address of the next hop for egress label. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpAddressFecOutLblMetric indicates the relative cost of the tunnel represented by this address FEC egress label. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpAddressFecOutLblMtu indicates the maximum transfer unit for payloads represented by this address FEC egress label. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpAddressFecOutLblLspId indicates the LSP id of the LSP for the RSVP tunnel used by LDP in LDP over RSVP associated with egress label. This object was obsoleted in release 13.0.

OBJECT-TYPE

vRtrLdpAddressFecMapTable is a read-only table which maps to the vRtrLdpAddressFecTable. This table has the same indexes as the vRtrLdpAddressFecTable but the order in which these indexes are specified is different for the two tables. In 13.0 this table has been replaced by TIMETRA-LDP-NG-MIB::vRtrLdpNgAddrFecMapTable.

OBJECT-TYPE

Each row entry represents an instance of an address FEC sent to or received from an LDP peer.

OBJECT-TYPE

The bit flags of vRtrLdpAddressFecMapFlags specify the characteristics of the FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpAddressFecMapNumInLabels gives the number of labels that have been sent to the peer associated with this FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpAddressFecMapNumOutLabels gives the number of labels that have been received from the peer associated with this FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

vRtrLdpAddrActiveFecTable is a read-only table that represents all active in data plane address FECs either sent to or received from an LDP peer known to the Virtual Router. In 13.0 this table has been replaced by TIMETRA-LDP-NG-MIB::vLdpNgAddrActiveFecTable.

OBJECT-TYPE

Each row entry represents an instance of an active in data plane address FEC sent to or received from an LDP peer.

OBJECT-TYPE

The value of vRtrLdpAddrActiveFecOpType indicates operation type of this FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

The bit flags of vRtrLdpAddrActiveFecFecFlags indicates the characteristics of the FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpAddrActiveFecNumInLbls indicates the number of labels that have been sent to the peer associated with this FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpAddrActiveFecNumOutLbls indicates the number of labels that have been received from the peer associated with this FEC. This object was obsoleted in release 13.0.

OBJECT-TYPE

vRtrLdpAddrActiveFecInLblTable is a read-only table that represents all active in data plane address FECs received from an LDP peer known to the Virtual Router. In 13.0 this table has been replaced by TIMETRA-LDP-NG-MIB::vLdpNgAddrActiveFecInLblTable.

OBJECT-TYPE

Each row entry represents an instance of an active in data plane address FEC received from an LDP peer.

OBJECT-TYPE

The value of vRtrLdpAddrActiveFecInLblId indicates the label number of the ingress label exchanged. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpAddrActiveFecInLbl indicates the ingress label exchanged. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpAddrActiveFecInLblIfIndex indicates the interface index for ingress label. This object was obsoleted in release 13.0.

OBJECT-TYPE

vRtrLdpAddrActiveFecOutLblTable is a read-only table that represents all active in data plane address FECs received from an LDP peer known to the Virtual Router. In 13.0 this table has been replaced by TIMETRA-LDP-NG-MIB::vLdpNgAddrActiveFecOutLblTable.

OBJECT-TYPE

Each row entry represents an instance of an active in data plane address FEC received from an LDP peer.

OBJECT-TYPE

The value of vRtrLdpAddrActiveFecOutLblId indicates the label number of the egress label exchanged. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpAddrActiveFecOutLbl indicates the egress label exchanged. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpAddrActiveFecOutLblStatus indicates the status of the egress label. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpAddrActiveFecOutLblIfIdx indicates the interface index for egress label. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpAddrActiveFecOutLblNHType indicates the address type of vRtrLdpAddrActiveFecOutLblNHAddr. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpAddrActiveFecOutLblNHAddr indicates the IP address of the next hop for egress label. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpAddrActiveFecOutLblMetric indicates the relative cost of the tunnel represented by this address FEC egress label. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpAddrActiveFecOutLblMtu indicates the maximum transfer unit for payloads represented by this address FEC egress label. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpAddrActiveFecOutLblLspId indicates the LSP id of the LSP for the RSVP tunnel used by LDP in LDP over RSVP associated with egress label. This object was obsoleted in release 13.0.

OBJECT-TYPE

vRtrLdpSessionInAddrTable is a read-only table that represents all local addresses either sent to or received from an LDP peer for a single session between an LDP entity and an LDP Peer. In 13.0 this table has been replaced by TIMETRA-LDP-NG-MIB::vRtrLdpNgSessionAddrTable.

OBJECT-TYPE

Each row entry represents an instance of all local addresses sent to or received from an LDP peer.

OBJECT-TYPE

The value of vRtrLdpSessionAddrLocalLdpId indicates the local LDP identifier for this LDP session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessionAddrNumInAddrs indicates the number of local addresses that have been received from the peer for this session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessionAddrNumOutAddrs indicates the number of local addresses that have been sent to the peer for this session. This object was obsoleted in release 13.0.

OBJECT-TYPE

vRtrLdpSessionInAddrTable is a read-only table that represents all local addresses received from an LDP peer for a single session between an LDP entity and an LDP Peer. In 13.0 this table has been replaced by TIMETRA-LDP-NG-MIB::vRtrLdpNgSessionInAddrTable.

OBJECT-TYPE

Each row entry represents an instance of a local address received from an LDP peer.

OBJECT-TYPE

The value of vRtrLdpSessionInAddrAddrType indicates the address type of vRtrLdpSessionInAddrAddress. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessionInAddrAddress indicates the IP address received from the peer for this LDP session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessionInAddrLocalLdpId indicates the local LDP identifier for this LDP session. This object was obsoleted in release 13.0.

OBJECT-TYPE

vRtrLdpSessionOutAddrTable is a read-only table that represents all local addresses sent to an LDP peer for a single session between an LDP entity and an LDP Peer. In 13.0 this table has been replaced by TIMETRA-LDP-NG-MIB::vRtrLdpNgSessionOutAddrTable.

OBJECT-TYPE

Each row entry represents an instance of a local address sent to an LDP peer.

OBJECT-TYPE

The value of vRtrLdpSessionOutAddrAddrType indicates the address type of vRtrLdpSessionOutAddrAddress. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessionOutAddrAddress indicates the IP address sent to the peer for this LDP session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpSessionOutAddrLocalLdpId indicates the local LDP identifier for this LDP session. This object was obsoleted in release 13.0.

OBJECT-TYPE

The value of vRtrLdpPeerTemplTableLstChanged indicates the last timestamp when an entry in the vRtrLdpPeerTemplTable was last changed.

OBJECT-TYPE

vRtrLdpPeerTemplTable provides an entry for each virtual router targeted peer template configuration to be used with LDP.

OBJECT-TYPE

Each row entry represents an targeted peer template on this virtual router that participates in the LDP protocol. Row entries can be created or deleted via SNMP SET requests. A row with default attribute values is created by setting vRtrLdpPeerTemplRowStatus to 'createAndGo'. A row entry can be destroyed by setting vRtrLdpPeerTemplRowStatus to 'destroy'.

OBJECT-TYPE

The value of vRtrLdpPeerTemplName uniquely identifies the name of the targeted peer template within a virtual router instance.

OBJECT-TYPE

The value of vRtrLdpPeerTemplLastChanged indicates the sysUpTime when this row was last modified.

OBJECT-TYPE

The value of vRtrLdpPeerTemplRowStatus specifies the row status of an entry in vRtrLdpPeerTemplTable.It is used to control the creation and deletion of rows. A row can be created by setting vRtrLdpPeerTemplRowStatus to 'createAndGo'. A row entry can be destroyed by setting vRtrLdpPeerTemplRowStatus to 'destroy'.

OBJECT-TYPE

The value of vRtrLdpPeerTemplAdminState specifies administrative state of the targeted peer template.

OBJECT-TYPE

The value of vRtrLdpPeerTemplInheritance specifies if the peer template entry in this row, should inherit the operational value of an object, or use the administratively set value. Non mask bits will always have value of zero, and any attempt to change the value will be silently discarded. This object is a bit-mask, with the following positions: vRtrLdpPeerTemplKeepAliveFactor 0x01 vRtrLdpPeerTemplKeepAliveTimeout 0x02 vRtrLdpPeerTemplHelloFactor 0x04 vRtrLdpPeerTemplHelloTimeout 0x08 vRtrLdpPeerTemplHelloReduction 0x10 vRtrLdpPeerTemplHelloReductnFctr 0x20 When the bit for an object has value of one, then the object's administrative and operational value are whatever the DEFVAL or most recently SET value. The mask bit(s) will be set to one when set is performed on the inherited object(s). Any attempt to set the mask bit to one will be silently discarded. When the bit for an object is set to zero, then the object's administrative and operational value are inherited from the corresponding targeted peer object in vRtrLdpGeneralTable.

OBJECT-TYPE

The value of vRtrLdpPeerTemplKeepAliveFactor specifies the value by which the keepalive timeout (vRtrLdpPeerTemplKeepAliveTimeout) should be divided to give the keepalive time i.e. the time interval, in seconds, between LDP keepalive messages. LDP keepalive messages are sent to keep the LDP session from timing out when no other LDP traffic is being sent between the neighbors.

OBJECT-TYPE

The value of vRtrLdpPeerTemplKeepAliveTimeout specifies the time interval, in seconds, that LDP waits before tearing down a session. If no LDP messages are exchanged during this time interval, the LDP session is torn down. Generally the value of vRtrLdpPeerTemplKeepAliveTimeout is configured to be three times the keepalive time (the time interval between successive LDP keepalive messages).

OBJECT-TYPE

The value of vRtrLdpPeerTemplHelloFactor specifies the value by which the hello timeout (vRtrLdpPeerTemplHelloTimeout) should be divided to give the hello time i.e. the time interval, in seconds, between LDP Hello messages. LDP uses hello messages to discover neighbors and to detect loss of connectivity with its neighbors.

OBJECT-TYPE

The value of vRtrLdpPeerTemplHelloTimeout specifies the hello time also known as hold time. It is the time interval, in seconds, that LDP waits before declaring a neighbor to be down. Hello timeout is local to the system and is sent in the hello messages to a neighbor. Hello timeout cannot be set to a value that is less than three times the hello time.

OBJECT-TYPE

The value of vRtrLdpPeerTemplTunneling specifies whether tunneling of LDP over tunnels is enabled. When this object has a value of 'true', tunneling is enabled. When its value is 'false', tunneling is disabled.

OBJECT-TYPE

The value of vRtrLdpPeerTemplBfdEnabled specifies whether BFD tracking of a LDP Session is enabled for this template. When this object has a value of 'true', BFD tracking is enabled. When its value is 'false', BFD tracking is disabled.

OBJECT-TYPE

The value of vRtrLdpPeerTemplLsrIfIndex specifies the local interface index that is to be used as source LSR-ID to establish targeted hello adjacency with a LDP peer.

OBJECT-TYPE

The value of vRtrLdpPeerTemplHelloReduction specifies whether hello reduction is enabled or not for this targeted peer template.If enabled, the sender advertises the dampened vRtrLdpPeerTemplHelloTimeout to the targeted peer after LDP session is established. The value of 'true' means targeted hello reduction is enabled.

OBJECT-TYPE

The value of vRtrLdpPeerTemplHelloReductnFctr specifies the number of hello messages that are sent at consistent vRtrLdpPeerTemplHelloTimeout, before advertising further dampened vRtrLdpPeerTemplHelloTimeout. An 'inconsistentValue' error is returned if this object is set when vRtrLdpPeerTemplHelloReduction is disabled.

OBJECT-TYPE

The value of vRtrLdpPeerTemplCreateTime indicates the sysUpTime when this LDP peer template was created.

OBJECT-TYPE

The value of vRtrLdpPeerTemplIndex indicates a unique value greater than zero which identifies this template for this virtual router in the Nokia SROS system. It is a unique value among entries within the same value of vRtrID. The value of vRtrLdpPeerTemplIndex represents the order in which the templates are created. This is also the order in which configuration will be saved. In the running system, this value may have gaps as templates are added and deleted. This is volatile object; hence, it is not persistent across reboot.

OBJECT-TYPE

The value of vRtrLdpPeerTemplLsrIdAdvert specifies whether or not advertisement of a local-LSR ID is sent over a given T-LDP session. When this object has a value of 'true', advertising is enabled, otherwise it is disabled.

OBJECT-TYPE

The value of vRtrLdpPeerTemplLsrIdCommunity defines a community string associated with a session to a given peer

OBJECT-TYPE

The value of vRtrLdpPeerTmplPlcyMpTblLstChgd indicates the last timestamp when an entry in the vRtrLdpPeerTemplPlcyMapTable was last changed.

OBJECT-TYPE

vRtrLdpPeerTemplPlcyMapTable maps targeted peer template entry to peer policy to be used with the Label Distribution Protocol (LDP).

OBJECT-TYPE

Each row entry maps a targeted peer template configuration to a set of policies for a virtual router in system. Row entries can be created or deleted via SNMP SET requests. A row is created by setting vRtrLdpPeerTemplPlcyMapRowStatus to 'createAndGo' provided the corresponding LSP id exists as an MPLS lsp. A row entry can be destroyed by setting vRtrLdpPeerTemplPlcyMapRowStatus to 'destroy'.

OBJECT-TYPE

The value of vRtrLdpPeerTemplPlcyMapLstChange indicates the sysUpTime when this row was last modified.

OBJECT-TYPE

The value of vRtrLdpPeerTemplPlcyMapRowStatus specifies the row status of an entry in vRtrLdpPeerTemplPlcyMapTable. A row can be created by setting vRtrLdpPeerTemplPlcyMapRowStatus to 'createAndGo'. A row entry can be destroyed by setting vRtrLdpPeerTemplPlcyMapRowStatus to 'destroy'.

OBJECT-TYPE

The value of vRtrLdpPeerTemplPlcyMapPolicy1 specifies the first targeted peer template policy.

OBJECT-TYPE

The value of vRtrLdpPeerTemplPlcyMapPolicy2 specifies the second targeted peer template policy.

OBJECT-TYPE

The value of vRtrLdpPeerTemplPlcyMapPolicy3 specifies the third targeted peer template policy.

OBJECT-TYPE

The value of vRtrLdpPeerTemplPlcyMapPolicy4 specifies the fourth targeted peer template policy.

OBJECT-TYPE

The value of vRtrLdpPeerTemplPlcyMapPolicy5 specifies the fifth targeted peer template policy.

OBJECT-TYPE

The value of vRtrLdpPeerTemplPlcyMapIndex indicates a unique value greater than zero which identifies this template policy map for this virtual router in the Nokia SROS system. It is a unique value among entries within the same value of vRtrID. The value of vRtrLdpPeerTemplPlcyMapIndex represents the order in which the template policy map are created. This is also the order in which configuration will be saved. In the running system, this value may have gaps as template policy maps are added and deleted. This is volatile object; hence, it is not persistent across reboot.

OBJECT-TYPE

The value of vRtrLdpPeerTemplPlcyMapCreateTim indicates the sysUpTime when this LDP peer template policy map was created.

OBJECT-TYPE

vRtrLdpPeerTemplPeerTable is a read-only table that represents all auto discovered peers for a peer template.

OBJECT-TYPE

Each row entry represents an auto discovered peer for a peer template.

OBJECT-TYPE

The value of vRtrLdpPeerTemplPeerAddrType indicates the address type of vRtrLdpPeerTemplPeerAddress.

OBJECT-TYPE

The value of vRtrLdpPeerTemplPeerAddress indicates the peer IP address.

OBJECT-TYPE

The value of vRtrLdpPeerTemplPeerCreateTime indicates the peer create time.

OBJECT-IDENTITY

OBJECT-IDENTITY