TIMETRA-LOG-MIB

TEXTUAL-CONVENTION

TEXTUAL-CONVENTION

The value of TmnxCFlash uniquely identifies a compact flash module on the active CPM card. A value of zero (0) indicates none specified.

TEXTUAL-CONVENTION

Each log event type has a unique identifying number. This number is unique within a particular software application, such as IP, MPLS, OSPF, etc.; but it is not necessarily unique across different software applications. That is MPLS event #1001 may be different from OSPF event #1001.

TEXTUAL-CONVENTION

The value of TmnxLogExRbkOperationType specifies the type of operation being performed.

TEXTUAL-CONVENTION

The value of TmnxLogFileId uniquely identifies a file-id to be used when creating a log or accounting file. A value of zero (0) indicates none specified and is invalid when used as an index for the tmnxLogFileIdTable.

TEXTUAL-CONVENTION

The value of TmnxLogFileType indicates the type of information that will be written to this file.

TEXTUAL-CONVENTION

The value of TmnxLogFilterEntryId is the identification number of an event log filter entry.

TEXTUAL-CONVENTION

The value of TmnxLogFilterId is the identification number of an event log filter. The value of zero indicates none specified. The value of zero (0) is invalid when used as an index for the tmnxLogFilterTable. Filter entry 1001 is created by the agent.

TEXTUAL-CONVENTION

When TmnxLogFilterOperator has a value of 'off', the item is not matched. Otherwise the value of TmnxLogFilterOperator determines the comparison operator to be used as the parameter match criterion.

TEXTUAL-CONVENTION

The value of tmnxLogIdIndex uniquely identifies an event stream log. Note that 3 default TmnxLogIdEntry rows are created by the agent using TmnxLogIdIndex values 99, 100 and 101.

TEXTUAL-CONVENTION

ITU perceived severity values as per M.3100 and X.733

TEXTUAL-CONVENTION

The value of TmnxStgIndex uniquely identifies an event stream log. It is the same as an TmnxLogIdIndex but with a limited range.

TEXTUAL-CONVENTION

The value of TmnxSyslogId uniquely identifies an entry in the tmnxSyslogTargetTable to be used for the syslog collector target information when creating a log file where tmnxLogIdDestination has a value of 'syslog (2)'.

TEXTUAL-CONVENTION

The value of TmnxSyslogIdOrEmpty uniquely identifies an entry in the tmnxSyslogTargetTable to be used for the syslog collector target information when creating a log file where tmnxLogIdDestination has a value of 'syslog (2)'. The value of 0 is used when no entry exists in the tmnxSyslogTargetTable.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

The value of tmnxLogFileDeletedLogId indicates with which event log-id or accounting-policy-id the deleted file was associated. Note the corresponding entry in the tmnxLogIdTable or tmnxLogApTable may no longer exist.

OBJECT-TYPE

The value of tmnxLogFileDeletedFileId indicates with which event log-id or accounting-policy-id the deleted file was associated. Note that the corresponding entry in the tmnxLogFileIdTable may no longer exist.

OBJECT-TYPE

The value of tmnxLogFileDeletedLogType indicates whether the deleted file was an 'eventLog' or 'accountingPolicy'.

OBJECT-TYPE

The value of tmnxLogFileDeletedLocation indicates on which compact flash device the event log or accounting policy file that has been deleted was located.

OBJECT-TYPE

The value of tmnxLogFileDeletedName indicates the pathname of an event log or accounting policy file that has been deleted because of space contention on a compact flash device.

OBJECT-TYPE

The value of tmnxLogFileDeletedCreateTime indicates the date and time when the deleted file had been created.

OBJECT-TYPE

The value of tmnxLogTraceErrorTitle indicates the title string of the trace error event that generated the tmnxLogTraceError notification.

OBJECT-TYPE

The value of tmnxLogTraceErrorSubject indicates the subject string of the trace error event that generated the tmnxLogTraceError notification. The subject is the entity that originated the event, such as the Slot ID.

OBJECT-TYPE

The value of tmnxLogTraceErrorMessage indicates the message text string of the trace error event that generated the tmnxLogTraceError notification.

OBJECT-TYPE

tmnxLogThrottledEventID is used by the tmnxLogEventThrottled notification to indicate the NOTIFICATION-TYPE object identifier of the throttled event.

OBJECT-TYPE

tmnxLogThrottledEvents is used by the tmnxLogEventThrottled notification to indicate the number of events dropped because of event throttling during the last throttle interval.

OBJECT-TYPE

tmnxSysLogTargetId is used by the tmnxSysLogTargetProblem notification to indicate the involved TmnxSyslogId.

OBJECT-TYPE

The value of tmnxSysLogTargetProblemDescr indicates the type of error encountered when trying to deliver events to the destination specified in the TmnxSyslogId.

OBJECT-TYPE

The value of tmnxLogNotifyApInterval indicates how frequently the statistics are collected and written to their destination.

OBJECT-TYPE

The value of tmnxStdReplayStartEvent indicates the SNMP notification request ID of the first missed event that was replayed when an SNMP notification target address was readded to the RTM following a period when the target address had been removed. It is used by the tmnxStdEventsReplayed notification.

OBJECT-TYPE

The value of tmnxStdReplayEndEvent indicates the SNMP notification request ID of the last missed event that was replayed when an SNMP notification target address was readded to the RTM following a period when the target address had been removed. It is used by the tmnxStdEventsReplayed notification.

OBJECT-TYPE

The value of tmnxEhsHEntryMinDelayInterval indicates the difference between the current time and the time as mentioned in tmnxEhsHEntryLastExecuted.

OBJECT-TYPE

The maximum number of concurrent active Logs that are allowed. A value of zero (0) for this object implies that there is no limit for the number of concurrent active logs in effect. The maximum number of logs in the Base context is restricted to 30 and in the VPRN context to 30.

OBJECT-TYPE

Defines the Nokia SROS series Log File ID Table for providing, via SNMP, the capability of defining the characteristics for log and accounting files and associating them with a file-id. The actual file is not created until the file-id is used in a log or accounting file configuration.

OBJECT-TYPE

Defines an entry in the tmnxLogFileIdTable. Entries are created and deleted in this table by SNMP sets to tmnxLogFileIdRowStatus.

OBJECT-TYPE

The index value tmnxLogFileId uniquely identifies a file-id to be used when creating a log or accounting file.

OBJECT-TYPE

This object allows entries to be created and deleted in the tmnxLogFileIdTable. Deletion of an entry in this table will not succeed if it is currently used by any log or accounting file.

OBJECT-TYPE

The storage type for this conceptual row. Conceptual rows having the value 'permanent' need not allow write access to any columnar objects in the row.

OBJECT-TYPE

The value of tmnxLogFileIdRolloverTime specifies how often, in minutes, a new log or accounting file will be created. If the value of tmnxLogFileIdLogType is not 'rollover', then the value of this object is irrelevant.

OBJECT-TYPE

The value of tmnxLogFileIdRetainTime specifies the minimum time, in hours, that a file is retained on the media. Once this time period has expired the file is deleted.

OBJECT-TYPE

The value of tmnxLogFileIdAdminLocation specifies where the log or accounting file should be created. The file location should be a compact flash on the primary CPM. When the secondary CPM becomes the primary CPM after a failure, the same log file policies will be activated. Thus it is recommended that the same media is available to both secondary and primary CPMs. If no location is specified, 0, the compact flash cf1: is used to store the log files or cf2: is used to store accounting files.

OBJECT-TYPE

The value of tmnxLogFileIdOperLocation indicates where the log or accounting file has been created. The file location should be a compact flash on the primary CPM. When the secondary CPM becomes the primary CPM after a failure, the same log file policies will be activated. Thus it is recommended that the same media is available to both secondary and primary CPMs.

OBJECT-TYPE

The value of tmnxLogFileIdDescription is a user provided description string for this log file-id entry. It can consist of any printable, seven-bit ASCII characters up to 80 characters in length.

OBJECT-TYPE

The value of tmnxLogFileIdLogType indicates the type of information that will be written to this file.

OBJECT-TYPE

The value of tmnxLogFileIdLogId indicates the ID index of the log or accounting policy this file is attached to. A value of zero (0) indicates that this file definition is not currently used by any log or accounting policy.

OBJECT-TYPE

The value of tmnxLogFileIdPathName is the pathname of the currently opened file used by this file-id entry. The value of tmnxLogFileIdPathName is affected by the value of stiPreferLocalTime.

OBJECT-TYPE

The value of tmnxLogFileIdCreateTime is the time the currently opened file version used by this file-id entry was created. The value of tmnxLogFileIdCreateTime is affected by the value of stiPreferLocalTime.

OBJECT-TYPE

The value of tmnxLogFileIdBackupLoc specifies where the log or accounting file should be created if it cannot be created in the location specified by tmnxLogFileIdAdminLocation. The file location should be a compact flash on the primary CPM. When the secondary CPM becomes the primary CPM after a failure, the same log file policies will be activated. Thus it is recommended that the same media is available to both secondary and primary CPMs. If no backup location is specified, 0, and the log or accounting file could not be created in the location specified by tmnxLogFileIdAdminLocation or the file creation at the specified backup location fails, a file create failure trap is issued and the associated log or accounting policy is marked as operationally 'outOfService'.

OBJECT-TYPE

The Nokia SROS series Log Accounting Policy Table contains an entry for each accounting policy that specifies the characteristics of the accounting records associated with an accounting policy.

OBJECT-TYPE

Defines an entry in the tmnxLogApTable. Entries in the tmnxLogApTable are created and destroyed via SNMP Set requests to tmnxLogApRowStatus.

OBJECT-TYPE

The value of tmnxLogApPolicyId uniquely identifies an accounting policy to be used for creating accounting records. A specific accounting policy can be applied to one or more service access points (SAPs). Any changes made to an existing policy is applied immediately to all SAPs where this policy is applied.

OBJECT-TYPE

This object allows entries to be created and deleted in the tmnxLogApTable. Deletion of an entry in this table will not succeed if it is currently applied to any service access point (SAP).

OBJECT-TYPE

The storage type for this conceptual row. Conceptual rows having the value 'permanent' need not allow write access to any columnar objects in the row.

OBJECT-TYPE

The value of tmnxLogApAdminStatus specifies the desired administrative state for this accounting policy.

OBJECT-TYPE

The value of tmnxLogApOperStatus indicates the current operational status of this accounting policy.

OBJECT-TYPE

The value of tmnxLogApInterval determines how frequently the statistics are collected and written to their destination. If no record is specified, default value for tmnxLogApInterval is 5 minutes. For service and network types of record, default values are 5 minutes and 15 minutes respectively. For SAA and PM only, the minimum value of tmnxLogApInterval is 1 minute. Otherwise the minimum value is 5 minutes.

OBJECT-TYPE

The value of tmnxLogApDescription is a user provided description string for this accounting policy. It can consist of any printable, seven-bit ASCII characters up to 80 characters in length.

OBJECT-TYPE

When tmnxLogApDefault has a value of 'true', it specifies that this accounting policy is applied to all service access points (SAPs) that do not have an explicit accounting policy applied. If no accounting policy is associated with a SAP accounting records are produced in accordance with the default policy. Only one accounting policy entry in the tmnxLogApTable can have tmnxLogApDefault set to 'true'. If there is no entry in the tmnxLogApTable with tmnxLogApDefault set to 'true', then the only accounting records collected are those explicitly configured accounting policies.

OBJECT-TYPE

The value of tmnxLogApRecord specifies the type of predefined accounting record type to be written to the accounting file. The value 'bsxSubscriberAppGroup (22)' was made obsolete in release 7.0 and replaced by 'customRecordAa (25).'

OBJECT-TYPE

The value of tmnxLogApToFileId is the index to the entry in the tmnxLogFileIdTable that specifies the file characteristics to be used for the destination of the accounting policy records collected by this accounting policy. The file itself is created the first time this accounting policy is applied to a service access point (SAP). tmnxLogApToFileId must be set along with tmnxLogApToFileType to indicate whether the records will be stored in a file or not. When a destination file is specified, the value of the file is specified by tmnxLogApToFileId and the value of tmnxLogApToFileType should be 'fileId'. When the destination file is not specified, the value of tmnxLogApToFileId should be zero and the value of tmnxLogApToFileType should be 'noFile'.

OBJECT-TYPE

The value of tmnxLogApPortType indicates the type of facility associated with the specified accounting policy's record type (i.e. tmnxLogApRecord).

OBJECT-TYPE

When tmnxLogApDefaultInterval has a value of 'true', it specifies that tmnxLogApInterval will have a default value. When tmnxLogApDefaultInterval has a value of 'false', user can set the value of tmnxLogApInterval manually.

OBJECT-TYPE

The value of tmnxLogApDataLossCount indicates the number of times a tmnxLogAccountingDataLoss trap was raised against this application policy.

OBJECT-TYPE

The value of tmnxLogApLastDataLossTimeStamp indicates the last time, since system startup that a tmnxLogAccountingDataLoss trap was raised against this application policy.

OBJECT-TYPE

The value of tmnxLogApToFileType specifies where records of an accounting policy are stored. It should be set along with tmnxLogApToFileId which specifies the destination file index where the accounting records are stored. When the value of tmnxLogApToFileType is 'noFile', it indicates that the accounting records will not to be stored in a file and the value of tmnxLogApToFileId should be set to zero. When the value of tmnxLogApToFileType is 'fileId', it indicates that the accounting records will be stored in a file specified by tmnxLogApToFileId. tmnxLogApOperStatus will transition to 'inService' when the tmnxLogApToFileType is set to 'noFile' or 'fileId'.

OBJECT-TYPE

The value of tmnxLogApIncludeSystemInfo specifies whether or not to include system information at the top of each accounting file generated for a given accounting policy.

OBJECT-TYPE

If true generation of accounting statistics is aligned with absolute time. First statistics are generated when absolute time is dividable by collection-interval value. After that it continues with collection-interval. This is important for synchronization of statistics interval between various nodes in network. If false, generation of accounting statistis is triggered right after command execution and continues after configured collection-interval. type that do not have an accounting policy.

OBJECT-TYPE

The Nokia SROS series Log Identification Table contains an entry for each log that specifies the characteristics of that log associated with a log-id number.

OBJECT-TYPE

Defines an entry in the tmnxLogIdTable. Entries in the tmnxLogIdTable are created and destroyed via SNMP Set requests to tmnxLogIdRowStatus. Default log entries 99, and 100 are created by the agent.

OBJECT-TYPE

The value of tmnxLogIdIndex uniquely identifies an event stream log.

OBJECT-TYPE

This object allows entries to be created and deleted in the tmnxLogIdTable. Deletion of an entry in this table will not succeed if tmnxLogIdOperStatus is not 'outOfService'. tmnxLogIdOperStatus will not transition to 'inService' if tmnxLogIdSource and tmnxLogIdDestination and their associated objects have not been set to valid values.

OBJECT-TYPE

The storage type for this conceptual row. Conceptual rows having the value 'permanent' need not allow write access to any columnar objects in the row.

OBJECT-TYPE

The value of tmnxLogIdAdminStatus specifies the desired administrative state for this log.

OBJECT-TYPE

The value of tmnxLogIdOperStatus indicates the current operational status of this log.

OBJECT-TYPE

The value of tmnxLogIdDescription is a user provided description string for this log. It can consist of any printable, seven-bit ASCII characters up to 80 characters in length.

OBJECT-TYPE

The value of tmnxLogIdFilterId is the index into the tmnxLogFilterTable to the entry the defines a filter to be applied to this log's source event stream to limit the events output to this log's destination. If tmnxLogIdFilterId has a value of 0, then all events in the source log are forwarded to the destination.

OBJECT-TYPE

The value of tmnxLogIdSource is a bit mask that specifies the log event source stream(s) to be forwarded to the destination specified in tmnxLogIdDestination. Events from more than one source may be forwarded to the log destination. The 'main' event stream consists of all events that are not explicitly directed to any other event stream. The 'security' event stream contains all events that affect attempts to breach system security such as failed login attempts, attempts to access SNMP MIB tables to which the user has not been granted access, or attempts to enter a branch of the CLI for which the user is not authorized. The 'user' activity event stream contains all events that directly affect the configuration or operation of the system. The 'debugTrace' event stream contains all events configured for application or protocol tracing. The 'li' event stream contains all events configured for Lawful Intercept activities. An attempt to set the 'li' event stream will fail with an inconsistentValue error if the requestor does not have access to the 'li' context. An attempt to set the 'li' event stream will fail with an inconsistentValue error if tmnxLogIdDestination has the value 'syslog' or 'file'.

OBJECT-TYPE

The value of tmnxLogIdDestination specifies the event log stream destination. Once this object has been set to a value other than the default 'none' it cannot be modified and attempts to reset it to another value will fail with an INCONSISTENT VALUE error. The 'console' destination causes all selected log events to be directed to the system console. If the console is not connected then all entries are dropped. The 'syslog' destination sends all selected log events to the syslog address configured in tmnxSyslogTargetAddress and tmnxSyslogTargetUdpPort in the tmnxSyslogTargetTable row entry pointed to by the value of tmnxLogIdSyslogId. An attempt to set this object to 'syslog' will fail with an inconsistentValue error if tmnxLogIdSource has the value 'li' set. The 'snmpTraps' destination causes events defined as SNMP traps to be sent to the configured SNMP trap destinations and also to be logged in the NOTIFICATION-LOG-MIB tables. The allocated memory size for the log of transmitted traps is specified in tmnxLogIdMaxMemorySize. The events are logged to memory in a circular fashion. Once the space is full, the oldest entry is replaced with a new entry. The 'file' destination causes all selected log events to be directed to a file on one of the CPM's compact flash discs. Details of the file's configuration are in the tmnxLogFileIdTable entry pointed to by the value of tmnxLogIdFileId. An attempt to set this object to 'file' will fail with an inconsistentValue error if tmnxLogIdSource has the value 'li' set. The 'memory' destination causes all selected log events to be directed to an in memory storage area. The allocated memory size for the log is specified in tmnxLogIdMaxMemorySize. The events are logged to memory in a circular fashion. Once the space is full, the oldest entry is replaced with a new entry.

OBJECT-TYPE

The value of tmnxLogIdFileId is the index to the entry in the tmnxLogFileIdTable that specifies the file characteristics to be used for the destination of the log events written to this log. tmnxLogIdOperStatus will not transition to 'inService' until a valid value has been set for tmnxLogIdFileId. This object is valid only if tmnxLogIdDestination is set to 'file'.

OBJECT-TYPE

The value of tmnxLogIdSyslogId is the index into the tmnxSyslogTargetTable for the row entry with the information to format event messages to be sent to a specific syslog collector target. This object is valid only when tmnxLogIdDestination has a value of 'syslog'. If this object has a value of zero (0), then no collector is specified and no messages are sent.

OBJECT-TYPE

The value of tmnxLogIdMaxMemorySize specifies the amount of memory to allocate for this log. This object is valid only when tmnxLogIdDestination has a value of 'memory', 'snmpTraps' or 'subscribedCli'. For any other value of tmnxLogIdDestination, a read of this object will return zero (0). Once a memory size has been specified and the log created, any attempt to modify this object will fail with an INCONSISTENT VALUE error.

OBJECT-TYPE

This object exists for the convenience of the Nokia SROS CLI. When set to 'true' it indicates that the 'CONSOLE' log output should be printed to the Telnet session instead of the CONSOLE device. When a tmnxLogIdEntry is created directly via SNMP, setting this object has no meaning and the 'CONSOLE' log output will always be sent to the CONSOLE device. This object is obsoleted in 15.0 Release.

OBJECT-TYPE

The value of tmnxLogIdForwarded is the count of the number of events that have been forwarded to this log's destination. This counter is incremented after an event has been selected by the log filter defined in tmnxLogIdFilterId.

OBJECT-TYPE

The value of tmnxLogIdDropped is the count of the number of events that have been sent to this logs source(s) and that have not been forwarded to the log destination because they were filtered out by the log filter defined in tmnxLogIdFilterId.

OBJECT-TYPE

The value of tmnxLogIdTimeFormat specifies the type of timestamp format for events sent to logs where tmnxLogIdDestination has a value of either 'syslog (2)' or 'file (4)'. When tmnxLogIdTimeFormat has a value of 'utc (1)' timestamps are written using the Coordinated Universal Time value. When tmnxLogIdTimeFormat has a value of 'local (2)' timestamps are written in the system's local time.

OBJECT-TYPE

The value of tmnxLogIdPythonPolicy specifies the name of a Python policy. The name refers to a conceptual row in the TIMETRA-PYTHON-MIB::tmnxPythonPolicyTable. The Python policy should have Python scripts to modify the log message text. While the value of tmnxLogIdAdminStatus is equal to 'inService', a non-empty value for this object is only allowed if the value of tmnxLogIdDestination is equal to 'syslog'.

OBJECT-TYPE

The value of tmnxLogIdOperDestination indicates the operational value of event log stream destination. The 'console' destination indicates all selected log events will be directed to the system console. The 'syslog' destination indicates all selected log events will be directed to the syslog address configured in tmnxSyslogTargetAddress and tmnxSyslogTargetUdpPort in the tmnxSyslogTargetTable row entry pointed to by the value of tmnxLogIdSyslogId. The 'snmpTraps' destination indicates events defined as SNMP traps will be sent to the configured SNMP trap destinations and also to be logged in the NOTIFICATION-LOG-MIB tables. The 'file' destination indicates all selected log events will be directed to a file on one of the CPM's compact flash discs. The 'memory' destination indicates all selected log events will be directed to an in memory storage area. The 'cliSession' destination indicates all selected log events will be directed to a cli session. tmnxLogIdDestination will have a value 'none' in this case.

OBJECT-TYPE

The value of tmnxLogIdNetconfStream specifies the name of the NETCONF stream associated with this log. A non-empty value for this object is only allowed if the value of tmnxLogIdDestination is equal to 'netconf'.

OBJECT-TYPE

OBJECT-TYPE

Information about a particular Log Filter entry. Entries are created by user. Entries are deleted by user. Entry 1001 is created by the agent for default TmnxLogIdIndex 100. There is no StorageType object. Entries have a presumed StorageType of nonVolatile.

OBJECT-TYPE

The value of tmnxLogFilterId is a unique index that identifies a particular entry in the tmnxLogFilterTable.

OBJECT-TYPE

Row entries in this table are created and destroyed via SNMP set requests.

OBJECT-TYPE

The value of tmnxLogFilterDescription is a user provided description string for this log filter. It can consist of any printable, seven-bit ASCII characters up to 80 characters in length.

OBJECT-TYPE

The action to take for packets that do not match any filter entries. the values default(3), and nat(5) are not allowed.

OBJECT-TYPE

When tmnxLogFilterInUse has a value of 'true', this filter is attached to a log file configuration. The same tmnxLogFilterEntry can be attached to more than one log file.

OBJECT-TYPE

A table of all log filter match entries for all log filters.

OBJECT-TYPE

Information about a particular Log Filter Parameter entry. Every Log Filter can have zero or more Log Filter Parameter match entries. The Log Filter parameter entries are checked in ascending order by their index value, tmnxLogFilterParamsIndex. Upon the first successful match, the specified actions are applied as indicated by the value of tmnxLogFilterParamsAction. No further checking against remaining tmnxLogFilterParamsEntry rows is done. Therefore, entries in this table should be sequenced from most to least explicit match criterion. It is recommended that multiple parameter entries for a log filter should be created with gaps between their index values. This allows a new entry to be inserted into an existing filter policy without needing to renumber the already existing filter parameters entries. A log filter entry in the tmnxLogFilterTable with no entry in the tmnxLogFilterParamsTable to define its match criteria set will match every log event, and the default action specified by tmnxLogFilterDefaultAction will be taken. Entries are created by user. Entries are deleted by user. There is no StorageType object, entries have a presumed StorageType of nonVolatile.

OBJECT-TYPE

OBJECT-TYPE

Row Status for this Log filter's parameter entry.

OBJECT-TYPE

The value of tmnxLogFilterParamsDescription is a user provided description string for this log filter match entry. It can consist of any printable, seven-bit ASCII characters up to 80 characters in length.

OBJECT-TYPE

the action to take for log events that match this filter entry. the value default(3) is allowed. If tmnxLogFilterParamsAction has the value 'default', the action specified by the value of tmnxLogFilterDefaultAction is applied to events that match this filter entry. The value nat(5) is not allowed.

OBJECT-TYPE

Matches log events with the specified application name. An application is the software entity the reports the log event and includes IP, MPLS, OSPF, CLI, SERVICES, etc.

OBJECT-TYPE

The value of tmnxLogFilterParamsApplOperator is the comparison operator to use to determine if the log event matches the value of tmnxLogFilterParamsApplication. The only valid values from TmnxLogFilterOperator are 'off', 'equal', and 'notEqual'.

OBJECT-TYPE

The value of tmnxLogFilterParamsNumber is the log event number to be matched. Event numbers uniquely identify a certain event within an application but not across applications.

OBJECT-TYPE

The value of tmnxLogFilterParamsNumberOperator is the comparison operator to use to determine if the log event matches the value of tmnxLogFilterParamsNumber.

OBJECT-TYPE

The value of tmnxLogFilterParamsSeverity is the log event severity level to be matched.

OBJECT-TYPE

The value of tmnxLogFilterParamsSeverityOperator is the comparison operator to use to determine if the log event matches the value of tmnxLogFilterParamsSeverity.

OBJECT-TYPE

The value of tmnxLogFilterParamsSubject is the log event subject string to be matched. The subject is the entity that the event is reported for, such as a port ID.

OBJECT-TYPE

The value of tmnxLogFilterParamsSubjectOperator is the comparison operator to use to determine if the log event matches the value of tmnxLogFilterParamsSubject. The only valid values of TmnxLogFilterOperator to use for the subject string comparison are 'off', 'equal', and 'notEqual'.

OBJECT-TYPE

The value of tmnxLogFilterParamsSubjectRegexp specifies the type of string comparison to use to determine if the log event matches the value of tmnxLogFilterParamsSubject. When the value of tmnxLogFilterParamsSubjectRegexp is 'true', the string in tmnxLogFilterParamsSubject is a regular expression string to be matched against the subject string in the log event being filtered. When it has a value of 'false', the string in tmnxLogFilterParamsSubject is matched exactly by the event filter.

OBJECT-TYPE

The value of tmnxLogFilterParamsRouter is the log event router context name string to be matched.

OBJECT-TYPE

The value of tmnxLogFilterParamsRouterOperator is the comparison operator to use to determine if the log event matches the value of tmnxLogFilterParamsRouter. The only valid values of TmnxLogFilterOperator to use for the router name string comparison are 'off', 'equal', and 'notEqual'.

OBJECT-TYPE

The value of tmnxLogFilterParamsRouterRegexp specifies the type of string comparison to use to determine if the log event matches the value of tmnxLogFilterParamsRouter. When the value of tmnxLogFilterParamsRouterRegexp is 'true', the string in tmnxLogFilterParamsRouter is a regular expression string to be matched against the router name string in the log event being filtered. When it has a value of 'false', the string in tmnxLogFilterParamsRouter is matched exactly by the event filter.

OBJECT-TYPE

The value of tmnxLogFilterParamsMsg specifies the log event message string to be matched. Matching result is determined based on value of tmnxLogFilterParamsMsgOperator. Matching type is determined based on value of tmnxLogFilterParamsMsgRegexp

OBJECT-TYPE

The value of tmnxLogFilterParamsMsgOperator specifies the comparison operator used to determine if the log event matches the value of tmnxLogFilterParamsMsg. The only valid values of tmnxLogFilterParamsMsgOperator to use for the string comparison are 'off', 'equal', and 'notEqual'.

OBJECT-TYPE

The value of tmnxLogFilterParamsMsgRegexp specifies the type of string comparison to use to determine if the log event matches the value of tmnxLogFilterParamsMsg. When the value of tmnxLogFilterParamsMsgRegexp is 'true', the string in tmnxLogFilterParamsMsg is a regular expression string to be matched against the message string in the log event being filtered. When it has a value of 'false', the string in tmnxLogFilterParamsMsg is matched as substring by the event filter.

OBJECT-TYPE

A table of all remote syslog collectors that this agent is configured to send syslog messages to.

OBJECT-TYPE

Information about a particular Syslog Target entry. Entries are created by user. Entries are deleted by user. There is no StorageType object, entries have a presumed StorageType of nonVolatile.

OBJECT-TYPE

The value of tmnxSyslogTargetIndex is a unique arbitrary identifier for this syslog collector target. The maximum value of tmnxSyslogTargetIndex is limited to 10 for the Base router context and to 30 for the VPRN context.

OBJECT-TYPE

The tmnxSyslogTargetRowStatus object allows for dynamic creation and deletion of row entries in the tmnxSyslogTargetTable as well as the activation and deactivation of these entries. When this object's value is set to 'notInService (2)', no messages will be sent to this target collector and none of its counters will be incremented. Refer to the RowStatus convention for further details on the behavior of this object.

OBJECT-TYPE

The value of tmnxSyslogTargetDescription is an administratively assigned textual description of this syslog collector target.

OBJECT-TYPE

The value of tmnxSyslogTargetAddress is the IPv4 address for this syslog message collector target. If the value of this object is '0.0.0.0', then no messages will be sent, nor will any counters be incremented. This object was made obsolete in release 5.0. It is replaced by the InetAddress pair tmnxSyslogTargetAddrType and tmnxSyslogTargetAddr.

OBJECT-TYPE

The value of tmnxSyslogTargetUdpPort is the UDP port number that is used to send messages to this syslog collector target.

OBJECT-TYPE

The value of tmnxSyslogTargetFacility is the syslog facility number that will be encoded in messages sent to this syslog collector target.

OBJECT-TYPE

The value of tmnxSyslogTargetSeverity is the maximum severity level of the messages that SHOULD be forwarded to this syslog collector target. The higher the level, the lower the severity.

OBJECT-TYPE

The value of tmnxSyslogTargetMessagePrefix is a string of ABNF alphanumeric characters to be prepended as the MSG TAG to the syslog MSG CONTENT string and separated from it with a colon and space, ': '.

OBJECT-TYPE

The value of tmnxSyslogTargetMessagesDropped is a count of messages not sent to this syslog collector target because the severity level of the message was above tmnxSyslogTargetSeverity; the higher the level, the lower the severity.

OBJECT-TYPE

The value of tmnxSyslogTargetAddrType specifies the type of host address to be used for the syslog message collector target. This object indicates the type of address stored in the corresponding tmnxSyslogTargetAddr object. Only 'ipv4', 'ipv6', and 'ipv6z' address types are supported.

OBJECT-TYPE

The value of tmnxSyslogTargetAddr specifies the IP host address to be used for the syslog message collector target. If no address is specified, ''H, then no messages will be sent nor will any counters be incremented. The syslog target address type is determined by the value of the corresponding tmnxSyslogTargetAddrType object.

OBJECT-TYPE

A table of all applications that generate TiMOS logger events.

OBJECT-TYPE

Information about a particular application entry. Entries are created by the agent when the system initializes. There is no StorageType object, entries have a presumed StorageType of permanent.

OBJECT-TYPE

The value of tmnxEventAppIndex is a unique arbitrary identifier for this application event generator.

OBJECT-TYPE

The value of tmnxEventAppName is the name string that is used in TiMOS log messages as the application that generated the logged event.

OBJECT-TYPE

A table of all TiMOS events that can be generated.

OBJECT-TYPE

Information about a particular TiMOS event type entry. Entries are created by the agent when the system initializes. There is no StorageType object, entries have a presumed StorageType of permanent.

OBJECT-TYPE

The value of tmnxEventID is a unique arbitrary identifier for indexing event type entries within an event generator application as identified by the value of tmnxEventAppIndex.

OBJECT-TYPE

The value of tmnxEventName is a short name string used to describe this event type.

OBJECT-TYPE

The value of tmnxEventSeverity specifies the severity level that will be associated with this type of event when it is generated.

OBJECT-TYPE

The value of tmnxEventControl determines whether or not events of this type will be generated or suppressed. When it has a value of 'true', the event is generated and tmnxEventCounter is incremented. When it has a value of 'false', the event is suppressed and tmnxEventDropCount is incremented.

OBJECT-TYPE

The value of tmnxEventCounter is the number of times an event of this type has been generated.

OBJECT-TYPE

The value of tmnxEventDropCount is the number of times and event of this type has been suppressed because tmnxEventControl is set to 'false'. When tmnxEventControl is set to 'true', tmnxEventDropCount indicates the number of events dropped because of logger input queue size overrun or dropped because of throttling when tmnxEventThrottle is set to 'true'.

OBJECT-TYPE

Setting tmnxEventReset to 'doAction (1)' causes the agent to reset the values of tmnxEventSeverity and tmnxEventControl to the default values for this event type.

OBJECT-TYPE

The value of tmnxEventThrottle determines whether or not events of this type will be throttled. When it has a value of 'true', the event is throttled at the rate indicated by the value of tmnxEventThrottleLimit and tmnxEventThrottleInterval. When it has a value of 'false', no event throttling is applied.

OBJECT-TYPE

The value of tmnxEventSpecThrottle specifies if events of this type will be throttled using the parameters specific for this event. When the value of tmnxEventSpecThrottle is equal to 'true', the event is throttled at the rate indicated by the value of tmnxEventSpecThrottleLimit and tmnxEventSpecThrottleIntval. When it has a value of 'false', no event-specific throttling is applied. The default value depends on the event.

OBJECT-TYPE

The value of tmnxEventSpecThrottleLimit specifies the number of times that this event can be logged within the tmnxEventSpecThrottleIntval. Once this limit has been reached, any additional events of this type will be dropped, i.e. tmnxEventDropCount will be incremented. At the end of the specific throttle interval if any events have been dropped a tmnxLogEventThrottled notification will be sent if the rate is applied to the whole stream of log events of this type; otherwise, if the rate is applied to each source of this type of event, the TIMETRA-SYSTEM-MIB::tmnxTrapDropped will be sent. The value must be zero while the value of tmnxEventSpecThrottle is 'false'. The default value depends on the event type.

OBJECT-TYPE

The value of tmnxEventSpecThrottleIntval specifies the number of seconds that the event-specific throttling interval lasts. The value must be zero while the value of tmnxEventSpecThrottle is 'false'. The default value depends on the event type.

OBJECT-TYPE

The value of tmnxEventSpecThrottleDef indicates the default value of tmnxEventSpecThrottle.

OBJECT-TYPE

The value of tmnxEventSpecThrottleLimitDef indicates the default value of the object tmnxEventSpecThrottleLimit. The value zero indicates that there is by default no event-specific throttling for this event.

OBJECT-TYPE

The value of tmnxEventSpecThrottleIntvalDef indicates the default value of tmnxEventSpecThrottleIntval. The value zero indicates that there is by default no event-specific throttling for this type of event.

OBJECT-TYPE

repeat

OBJECT-TYPE

A table of all remote SNMP trap collectors to which this agent is configured to send SNMP notifications messages. This table was made obsolete in the 5.0 release and is replaced with tmnxSnmpTrapDestTable.

OBJECT-TYPE

Information about a particular SNMP trap destination entry. The first index instance creates and snmp trap group to be associated with the event log with the same value for tmnxLogIdIndex. The second and third indexes specify a remote SNMP trap destination that will be sent SNMP notification messages from the associated event log. Entries are created by user. Entries are deleted by user. There is no StorageType object, entries have a presumed StorageType of nonVolatile. This table was made obsolete in the 5.0 release and is replaced with the tmnxSnmpTrapDestTable.

OBJECT-TYPE

The value of tmnxStgIndex specifies an snmp trap group to be associated with the event log with the same value for tmnxLogIdIndex. This object was made obsolete in the 5.0 release. It is replaced by tmnxStdIndex.

OBJECT-TYPE

The value of tmnxStgDestAddress is the IPv4 address for this remote snmp notification destination. If the value of this object is '0.0.0.0', then no messages will be sent, nor will any counters be incremented. This object was made obsolete in the 5.0 release. It is replaced by the InetAddressType/InetAddress objects tmnxStdDestAddrType and tmnxStdDestAddr.

OBJECT-TYPE

The value of tmnxStgDestPort is the UDP port number that is used to send messages to this remote SNMP notification destination. This object was made obsolete in the 5.0 release. It is replaced by tmnxStdDestPort.

OBJECT-TYPE

The tmnxStgRowStatus object allows for dynamic creation and deletion of row entries in the tmnxSnmpTrapGroupTable as well as the activation and deactivation of these entries. When this object's value is set to 'notInService (2)', no messages will be sent to this snmp trap group and none of its counters will be incremented. Refer to the RowStatus convention for further details on the behavior of this object. This object was made obsolete in the 5.0 release. It is replaced by tmnxStdRowStatus.

OBJECT-TYPE

The value of tmnxStgDescription is an administratively assigned textual description of this snmp trap destination. This object was made obsolete in the 5.0 release. It is replaced by tmnxStdDescription.

OBJECT-TYPE

The value of tmnxStgVersion specifies the SNMP version that will be used to format notification messages sent to this snmp trap destination. The values supported by the Nokia SROS series SNMP agent are: 0 for SNMPv1 1 for SNMPv2c 3 for SNMPv3 This object was made obsolete in the 5.0 release. It is replaced by tmnxStdVersion.

OBJECT-TYPE

The value of tmnxStgNotifyCommunity specifies the SNMPv1 or SNMPv2c community name string or the SNMPv3 security name used when an SNMP notification message is sent to this trap destination. If the value of this object is the empty string, then no messages will be sent nor will any counters be incremented. This object was made obsolete in the 5.0 release. It is replaced by tmnxStdVersion.

OBJECT-TYPE

The value of tmnxStgSecurityLevel specifies the level of security at which SNMP notification messages will be sent to the SNMP trap destination when tmnxStgVersion has a value of '3' for SNMPv3. This object was made obsolete in the 5.0 release. It is replaced by tmnxStdSecurityLevel.

OBJECT-TYPE

Setting tmnxEventTest to 'doAction' causes the tmnxTestEvent notification to be generated.

OBJECT-TYPE

The value of tmnxEventThrottleLimit specifies the number of log events that can be logged within the tmnxEventThrottleInterval for a specific entry in the tmnxEventTable. Once the limit has been reached, any additional events of that type will be dropped, i.e. tmnxEventDropCount will be incremented. At the end of the throttle interval if any events have been dropped a tmnxLogEventThrottled notification will be sent.

OBJECT-TYPE

The value of tmnxEventThrottleInterval specifies the number of seconds that an event throttling interval lasts.

OBJECT-TYPE

The value of tmnxSnmpSetErrsMax indicates the maximum number of entries the agent will create in the tmnxSnmpSetErrsTable. Once the table is full the agent will delete the oldest entry in the table in order to add new entries.

OBJECT-TYPE

A table of recent SNMP SET failures. Only the SET errs from remote SNMP manager requests are saved in this table. Only SET errs detected by the SNMP engine in the test phase consistency check method functions are saved. SET errors that are caught by the preliminary access and ASN.1 decoding phase are not saved. These are errs such as noAccess, notWritable, wrongType, wrongLength and wrongEncoding. Note that notWritable, wrongType, and wrongLength errs may sometimes be generated by the consistency check; in this case they will be saved in this table. SET errs caused by local CLI sessions are not saved. The tmnxSnmpSetErrsTable is intended to provide an aide to Network Management Systems (NMS) developers. When an SNMP SET fails during the consistency checking test phase, this table may provide more detailed failure reason information than the simple SNMP error code value in the SNMP response PDU.

OBJECT-TYPE

Information about a particular SNMP SET error. The first two index instances identify the SNMP manager who sent the SNMP SET request that failed. The third index specifies the SNMP request ID (sequence number) of the SNMP SET request that failed. Entries are created by the agent. Entries are deleted by the agent. There is no StorageType object, entries have a presumed StorageType of volatile.

OBJECT-TYPE

The value of tmnxSseAddressType indicates the IP address type of address specified in tmnxSseAddress. 'ipv4' and 'ipv6' are the only address type values supported.

OBJECT-TYPE

The value of tmnxSseAddress is the IP address of the SNMP manager that sent the SNMP SET request that failed for this error reason.

OBJECT-TYPE

The value of tmnxSseSnmpPort is the UDP port number of the SNMP manager that sent the SNMP SET request that failed for this error reason.

OBJECT-TYPE

The value of tmnxSseRequestId indicates the request ID of the SNMP SNMP SET request that failed for this error reason.

OBJECT-TYPE

The value of tmnxSseVersion indicates the SNMP version of the SNMP SET request that failed. The values supported by the Nokia SROS series SNMP agent are: 0 for SNMPv1 1 for SNMPv2c 3 for SNMPv3

OBJECT-TYPE

The value of tmnxSseSeverityLevel indicates severity level that is associated with this type SNMP SET error.

OBJECT-TYPE

The value of tmnxSseModuleId indicates a unique arbitrary identified for the TiMOS application module that generated this SNMP SET error. NOTE: This is NOT the same value used for tmnxEventAppIndex.

OBJECT-TYPE

The value of tmnxSseModuleName indicates the name string of the TiMOS application module that generated this SNMP SET error. NOTE: This is NOT the same value used for tmnxEventAppName.

OBJECT-TYPE

The value of tmnxSseErrorCode indicates the error number associated with this SNMP SET error. The error numbers are unique within a tmnxSseModuleId. They are not unique across all modules so both the module name and error number are required to identify a particular error message.

OBJECT-TYPE

The value of tmnxSseErrorName indicates the error name associated with this SNMP SET error. The error names are unique within a tmnxSseModuleId. They are not unique across all modules so both the module name and error name are required to identify a particular error message.

OBJECT-TYPE

The value of tmnxSseErrorMsg indicates the fixed error message text associated with this SNMP SET error identified by the values of tmnxSseModuleId and tmnxSseErrorCode.

OBJECT-TYPE

The value of tmnxSseExtraText indicates the fixed run-time variable message text associated with this SNMP SET error identified by the values of tmnxSseModuleId and tmnxSseErrorCode. If the extra text was truncated to fit into buffer size allowed, the last character will be an asterisk (*).

OBJECT-TYPE

The value of tmnxSseTimestamp indicates the sysUpTime value when this tmnxSnmpSetErrsEntry was created by the agent.

OBJECT-TYPE

A table of all remote SNMP trap logs to which this agent is configured to send SNMP notifications messages.

OBJECT-TYPE

Each row entry in the tmnxSnmpTrapLogTable represents additional columns for attributes specific to the Nokia SROS series implementation of SNMP-NOTIFICATION-MIB::snmpNotifyTable.

OBJECT-TYPE

The value of tmnxSnmpTrapLogDescription is an administratively assigned textual description of this snmp trap log.

OBJECT-TYPE

A table of all remote SNMP IPv4/v6 trap collectors to which this agent is configured to send SNMP notification messages.

OBJECT-TYPE

Information about a particular SNMP notification destination entry. The first index instance creates an snmp notification group to be associated with the event log with the same value for tmnxLogIdIndex. The second index specifies an administrative name to identify a specific SNMP notification target. Entries are created by user. Entries are deleted by user. There is no StorageType object, entries have a presumed StorageType of nonVolatile.

OBJECT-TYPE

The value of tmnxStdIndex specifies an snmp notification group to be associated with the event log with the same value for tmnxLogIdIndex.

OBJECT-TYPE

The value of tmnxStdName specifies the name of an snmp notification destination within the snmp notification group specified by tmnxLogIdIndex.

OBJECT-TYPE

The tmnxStdRowStatus object allows for dynamic creation and deletion of row entries in the tmnxSnmpTrapDestTable as well as the activation and deactivation of these entries. In order for 'createAndGo' row creation to succeed or status to transition to 'active' a value must be set for tmnxStdNotifyCommunity. In order for 'createAndGo' row creation to succeed or status to transition to 'active' an entry must exist in the SNMP-NOTIFICATION-MIB::snmpNotifyTable with an snmpNotifyName index that is the ASCII string representation of the value of tmnxStdIndex. When this object's value is set to 'notInService (2)', no messages will be sent to this snmp notification collector and none of its counters will be incremented. Refer to the RowStatus convention for further details on the behavior of this object.

OBJECT-TYPE

The value of tmnxStdRowLastChanged indicates the sysUpTime when the value of a writable object in this row entry was modified.

OBJECT-TYPE

The value of tmnxStdDestAddrType specifies the type of host address to be used for the remote SNMP notification collector. This object indicates the type of address stored in the corresponding tmnxStdDestAddr object. If the value of this object is 'unknown', then no messages will be sent nor will any counters be incremented. If tmnxStdDestAddrType is not set in the same PDU with tmnxStdDestAddr, the set request will fail with an inconsistentValue error.

OBJECT-TYPE

The value of tmnxStdDestAddr specifies the IP host address to be used for the remote SNMP notification collector. The SNMP notification collector IP address type is determined by the value of the corresponding tmnxStdDestAddrType object. If the value of this object is empty or all NULLs, then no messages will be sent nor will any counters be incremented. If tmnxStdDestAddrType is not set in the same PDU with tmnxStdDestAddr, the set request will fail with an inconsistentValue error.

OBJECT-TYPE

The value of tmnxStdDestPort is the UDP port number that is used to send messages to this remote SNMP notification collector.

OBJECT-TYPE

The value of tmnxStdDescription is an administratively assigned textual description of this SNMP notification collector.

OBJECT-TYPE

The value of tmnxStdVersion specifies the SNMP version that will be used to format notification messages sent to this SNMP notification collector. The values supported by the Nokia SROS series SNMP agent are: 0 for SNMPv1 1 for SNMPv2c 3 for SNMPv3

OBJECT-TYPE

The value of tmnxStdNotifyCommunity specifies the SNMPv1 or SNMPv2c community name string or the SNMPv3 security name used when an SNMP notification message is sent to this SNMP notification collector. If the value of this object is the empty string, then no messages will be sent nor will any counters be incremented.

OBJECT-TYPE

The value of tmnxStdSecurityLevel specifies the level of security at which SNMP notification messages will be sent to the SNMP notification collector when tmnxStdVersion has a value of '3' for SNMPv3.

OBJECT-TYPE

The value of tmnxStdReplay specifies whether or not to resend notifications that were generated while this notification destination did not have a route installed for it in the route tables.

OBJECT-TYPE

The value of tmnxStdReplayStart indicates the SNMP notification request ID of the first event that could not be generated because there is no route to this notification target address. Events will be resent when this notification target address is readded to the route tables, on either an in-band or out-of-band interface. The agent searches backwards in the event log and begins resending events from the oldest event that has a timestamp <= 5 centiseconds less than the timestamp of the event with this request ID. Note that if the outage is long and a large number of events are generated in the meantime, it is possible that the log memory storage has wrapped and the event data for this request ID is no longer available. In that case, the oldest event saved in the log will be the first event resent. A value of 0 indicates that there are no missed events waiting to be resent.

OBJECT-TYPE

The value of tmnxStdReplayLastTime indicates the sysUpTime when missed events were last replayed to this SNMP notification target address. A value of 0 indicates that no missed events have been replayed to this SNMP notification target address.

OBJECT-TYPE

The maximum number of tmnxSnmpTrapDestTable row entries that can be created for a specific tmnxStdIndex that represents an snmp notification group.

OBJECT-TYPE

The Nokia SROS series tmnxLogApCustRecordTable augments tmnxLogApTable. The table allows to configure the layout and setting for a custom accounting record associated with this accounting policy.

OBJECT-TYPE

Defines an entry in the tmnxLogApCustRecordTable. Entries in this table are created and destroyed via SNMP Set requests to the tmnxLogApRowStatus object of the tmnxLogApTable.

OBJECT-TYPE

The value of tmnxLogApCrLastChanged indicates the sysUpTime when an object in this table was last modified. A Value 0 means that no change was made to this row since the box was last initialized.

OBJECT-TYPE

The value of tmnxLogApCrSignChangeDelta specifies the delta change (significant change) that is required for the custom record to be written to the xml file.

OBJECT-TYPE

The value of tmnxLogApCrSignChangeQueue specifies the reference queue to which the significant change defined in tmnxLogApCrSignChangeDelta applies.

OBJECT-TYPE

The value of tmnxLogApCrSignChangeOCntr specifies the counter-id that will be taken as reference to which the significant change defined in tmnxLogApCrSignChangeDelta applies.

OBJECT-TYPE

The value of tmnxLogApCrSignChangeQICounters specifies the ingress counter Ids in the queue defined by tmnxLogApCrSignChangeQueue to be taken as reference to which the significant change defined in tmnxLogApCrSignChangeDelta applies. A non-zero value of this object is only allowed if the object tmnxLogApCrSignChangeQueue has a non-zero value.

OBJECT-TYPE

The value of tmnxLogApCrSignChangeQECounters specifies the egress counter Ids in the queue defined by tmnxLogApCrSignChangeQueue to be taken as reference to which the significant change defined in tmnxLogApCrSignChangeDelta applies. A non-zero value of this object is only allowed if the object tmnxLogApCrSignChangeQueue has a non-zero value.

OBJECT-TYPE

The value of tmnxLogApCrSignChangeOICounters specifies the ingress counter Ids in the counter-group defined by tmnxLogApCrSignChangeOCntr to be taken as reference to which the significant change defined in tmnxLogApCrSignChangeDelta applies. A non-zero value of this object is only allowed if the object tmnxLogApCrSignChangeOCntr has a non-zero value.

OBJECT-TYPE

The value of tmnxLogApCrSignChangeOECounters specifies the egress counter Ids in the counter-group defined by tmnxLogApCrSignChangeOCntr to be taken as reference to which the significant change defined in tmnxLogApCrSignChangeDelta applies. A non-zero value of this object is only allowed if the object tmnxLogApCrSignChangeOCntr has a non-zero value.

OBJECT-TYPE

The value of tmnxLogApCrSignChangeAACounters specifies the AA (Application assurance) counter Ids to be taken as reference to which the significant change defined in tmnxLogApCrSignChangeDelta applies. A non-zero value of this object is only allowed if both the objects tmnxLogApCrSignChangeOCntr and tmnxLogApCrSignChangeQueue are zero. Also, a non-zero value for this object is only allowed if the object tmnxLogApCrSignChangeDelta is either 0 or 1.

OBJECT-TYPE

The value of tmnxLogApCrAACounters specifies the list of AA (Application Assurance) counters that need to be collected in this custom record.

OBJECT-TYPE

The value of tmnxLogApCrAASubAttributes specifies the list of AA (Application Assurance) subscriber attributes that must be included in this custom record.

OBJECT-TYPE

The value of tmnxLogApCrSignChangePolicer specifies the reference policer to which the significant change defined in tmnxLogApCrSignChangeDelta applies. A value of zero means that the significant change does not apply to any policer. A value of minus one means that the significant change applies to any policer.

OBJECT-TYPE

The value of tmnxLogApCrSignChangePICounters specifies the ingress counters in the policer defined by tmnxLogApCrSignChangePolicer to which the significant change defined in tmnxLogApCrSignChangeDelta applies. A non-empty value of this object is only allowed if the object tmnxLogApCrSignChangePolicer has a non-zero value.

OBJECT-TYPE

The value of tmnxLogApCrSignChangePECounters specifies the egress counters in the policer defined by tmnxLogApCrSignChangePolicer to which the significant change defined in tmnxLogApCrSignChangeDelta applies. A non-empty value of this object is only allowed if the object tmnxLogApCrSignChangeQueue has a non-zero value.

OBJECT-TYPE

The Nokia SROS series tmnxLogApCustRecordQueueTable allows to create custom record queue information for a given accounting policy. Rows can only be created for existing accounting policies (as defined in tmnxLogApTable).

OBJECT-TYPE

Defines an entry in the tmnxLogApCustRecordQueueTable. Entries in this table are created and destroyed via SNMP Set requests.

OBJECT-TYPE

The value of tmnxLogApCrQueueId specifies the queue ID for which counters will be collected in this custom record. The counters that will be collected are defined in tmnxLogApCrQueueICounters and tmnxLogApCrQueueECounters.

OBJECT-TYPE

Row Status of the entry. This allows creation/deletion of rows in this table.

OBJECT-TYPE

The value of tmnxLogApCrQueueLastChanged indicates the sysUpTime when an object in this table was last modified. A Value 0 means that no change was made to this row since it was created.

OBJECT-TYPE

The value of tmnxLogApCrQueueICounters specifies the list of ingress counters that need to be collected in this custom record. At least one of the objects tmnxLogApCrQueueICounters or tmnxLogApCrQueueECounters must have a non-zero value.

OBJECT-TYPE

The value of tmnxLogApCrQueueECounters specifies the list of egress counters that need to be collected in this custom record. At least one of the objects tmnxLogApCrQueueICounters or tmnxLogApCrQueueECounters must have a non-zero value.

OBJECT-TYPE

The Nokia SROS series tmnxLogApCrOverrideCntrTable allows to create custom record counter override information for a given accounting policy. Rows can only be created for existing accounting policies (as defined in tmnxLogApTable).

OBJECT-TYPE

Defines an entry in the tmnxLogApCrOverrideCntrTable. Entries in this table are created and destroyed via SNMP Set requests.

OBJECT-TYPE

The value of tmnxLogApCrOverrideCntrId specifies the counter group for which counters will be collected in this custom record. The counters that will be collected are defined in tmnxLogApCrOverrideCntrICounters and tmnxLogApCrOverrideCntrECounters.

OBJECT-TYPE

Row Status of the entry. This allows creation/deletion of rows in this table.

OBJECT-TYPE

The value of tmnxLogApCrOverrideCntrLastChngd indicates the sysUpTime when an object in this table was last modified. A Value 0 means that no change was made to this row since it was created.

OBJECT-TYPE

The value of tmnxLogApCrOverrideCntrICounters specifies the list of ingress counters that need to be collected in this custom record. At least one of the objects tmnxLogApCrOverrideCntrICounters or tmnxLogApCrOverrideCntrECounters must have a non-zero value.

OBJECT-TYPE

The value of tmnxLogApCrOverrideCntrECounters specifies the list of egress counters that need to be collected in this custom record. At least one of the objects tmnxLogApCrOverrideCntrICounters or tmnxLogApCrOverrideCntrECounters must have a non-zero value.

OBJECT-TYPE

The value of tmnxEventPrimaryRoutePref specifies the primary routing preference for traffic generated for SNMP notifications and syslog messages. A value of 'inband' specifies that the Logging utility will attempt to use the Base routing context to send SNMP notifications and syslog messages to remote destinations. A value of 'outband' specifies that the Logging utility will attempt to use the management routing context to send SNMP notifications and syslog messages to remote destinations. If the remote destination, as specified by tmnxStdDestAddr or tmnxSyslogTargetAddr, is not reachable via the routing context specified by tmnxEventPrimaryRoutePref, the secondary routing preference as specified by tmnxEventSecondaryRoutePref will be attempted.

OBJECT-TYPE

The value of tmnxEventSecondaryRoutePref specifies the secondary routing preference for traffic generated for SNMP notifications and syslog messages. The routing context specified by the tmnxEventSecondaryRoutePref will be attempted if the remote destination was not reachable by the primary routing preference, specified by tmnxEventPrimaryRoutePref. The value specified for tmnxEventSecondaryRoutePref must be distinct from the value for tmnxEventPrimaryRoutePref. A value of 'inband' specifies that the Logging utility will attempt to use the Base routing context to send SNMP notifications and syslog messages to remote destinations. A value of 'outband' specifies that the Logging utility will attempt to use the management routing context to send SNMP notifications and syslog messages to remote destinations. A value of 'none' specifies that no attempt will be made to send SNMP notifications and syslog messages to remote destinations. If the remote destination, as specified by tmnxStdDestAddr or tmnxSyslogTargetAddr, is not reachable via the routing contexts specified by tmnxEventPrimaryRoutePref and tmnxEventSecondaryRoutePref, the Log utility will fail to send SNMP notifications and syslog messages to the remote destination.

OBJECT-TYPE

The value of tmnxLogConfigEventsDamped specifies whether or not the module generating tmnxConfigCreate, tmnxConfigDelete, and tmnxConfigModify events applies a damping algorithm. WARNING: While this event damping is original behavior for some modules such as service manager, QoS, and filters it can result in the NMS system database being out of sync because of missed change events. On the other hand, if the damping is disabled, 'false', it may take much longer for a large CLI configuration file to be processed when manually 'exec'ed after system bootup.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

The value of the object tmnxLogExRbkOpTblLastChange indicates the value of sysUpTime at the time of the last modification of a row entry in the tmnxLogExecRollbackOpTable.

OBJECT-TYPE

The value of the object tmnxLogExRbkOpMaxEntries specifies the maximum number of row entries supported in the tmnxLogExecRollbackOpTable.

OBJECT-TYPE

The Nokia SROS series tmnxLogExecRollbackOpTable provides a history of up to the last number of 'exec', 'load', rollback revert, and 'vsd' operations specified by the value of tmnxLogExRbkOpMaxEntries. The tmnxLogExecRollbackOpTable is intended to provide an aide to Network Management Systems (NMS). The 'exec' or 'load' of a large configuration file via the system's CLI, a large rollback revert operation, or execution of 'vsd' configuration messages will generate so many configuration change and other events in a short time that neither the SROS's event logging utility nor the NMS can keep up with them. This results in the SROS and/or NMS dropping events and requires the NMS to perform a costly resynchronization of its management database.

OBJECT-TYPE

Defines a row entry in the tmnxLogExecRollbackOpTable. Entries in this table are created and deleted by the agent.

OBJECT-TYPE

The value of tmnxLogExRbkOpIndex is a unique value that indicates an instance of an exec, load, rollback revert, or vsd operation. Only the most recent instances are kept in this table. The maximum number of row entries supported in this table is specified by the value of tmnxLogExRbkOpMaxEntries.

OBJECT-TYPE

The value of tmnxLogExRbkOpLastChanged indicates the sysUpTime when an object in this table was last modified. A Value 0 means that no change was made to this row since it was created.

OBJECT-TYPE

The value of tmnxLogExRbkOpType indicates the type of operation this row entry represents.

OBJECT-TYPE

The value of tmnxLogExRbkOpStatus indicates the status of this exec, load, rollback revert, or vsd operation.

OBJECT-TYPE

The value of tmnxLogExRbkOpBegin indicates the sysUpTime when the exec, load, rollback revert, or vsd operation began.

OBJECT-TYPE

The value of tmnxLogExRbkOpEnd indicates the sysUpTime when the exec, load, rollback revert, or vsd operation ended. A value of zero (0) means that the operation has not completed.

OBJECT-TYPE

The value of tmnxLogExRbkOpFile indicates the location and name of the file used for the exec, load or rollback revert operation, otherwise the value of this object is an empty string.

OBJECT-TYPE

The value of tmnxLogExRbkOpUser indicates the user who initiated the exec or rollback revert operation.

OBJECT-TYPE

The value of tmnxLogExRbkOpNumEvents indicates the number of row entries in the associated tmnxLogExecRollbackEventTable for this exec, load, rollback revert, or vsd operation. It is updated only when the exec, load, rollback revert, or vsd operation ends. A value of zero (0) means that the operatio has not completed.

OBJECT-TYPE

The Nokia SROS series tmnxLogExecRollbackEventTable provides a history of mib tables modified or specific events generated during an exec, load, rollback revert, or vsd operation.

OBJECT-TYPE

Defines a row entry in the tmnxLogExecRollbackEventTable. Each row entry represents either an SNMP table that has been modified or a specific event generated during an exec, load, rollback revert, or vsd operation. Entries in this table are created and deleted by the agent.

OBJECT-TYPE

The value of tmnxLogExRbkEventIndex is a unique value that indicates an instance of an event generated during an exec, load, rollback revert, or vsd operation.

OBJECT-TYPE

The value of tmnxLogExRbkEventOID indicates the object identifier of either a mib table for which a generic change event was generated or the notification object identifier of a specific event notification generated during the the exec, load, rollback revert, or vsd operation. The generic change events are tmnxConfigCreate, tmnxConfigDelete, tmnxConfigModify, and tmnxStateChange notifications. For these event types, the value of tmnxLogExRbkEventOID is the object identifier specified by the tmnxNotifyEntryOID varbind. For specific events generated during an exec, load or rollback revert or vsd, the value of this object is the notification object identifier itself. An object identifier will appear only once in this table.

OBJECT-IDENTITY

OBJECT-TYPE

The value of tmnxLogExecRollbackOpIndex is a unique value that indicates a row entry instance of an exec, load, rollback revert, or vsd operation in the tmnxLogExecRollbackOpTable. It is included in the 'exec', 'load' and rollback revert start and end notifications.

OBJECT-TYPE

The value of tmnxLogExecRollbackOpType indicates the type of operation being performed. It is included in the 'exec', 'load' and rollback revert start and end notifications.

OBJECT-TYPE

The value of tmnxLogColdStartWaitTime specifies the time delay that must pass before notifying specific CPM applications that a route is available after a cold reboot.

OBJECT-TYPE

The value of tmnxLogRouteRecoveryWaitTime specifies the time delay that must pass before notifying specific CPM applications after the recovery or change of a route during normal operation.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

The value of the object tmnxEhsHandlerTblLastChange indicates the value of sysUpTime at the time of the last modification of a row in the tmnxEhsHandlerTable.

OBJECT-TYPE

The value of the object tmnxEhsHandlerMaxEntries specifies the maximum number of row entries supported in the tmnxEhsHandlerTable.

OBJECT-TYPE

The value of the object tmnxEhsHEntryTblLastChange indicates the value of sysUpTime at the time of the last modification of a row in the tmnxEhsHEntryTable.

OBJECT-TYPE

The value of the object tmnxEhsHEntryMaxEntries specifies the maximum number of row entries supported in the tmnxEhsHEntryTable.

OBJECT-TYPE

The value of the object tmnxEhsTriggerTblLastChange indicates the value of sysUpTime at the time of the last modification of a row in the tmnxEhsTriggerTable.

OBJECT-TYPE

The value of the object tmnxEhsTriggerMaxEntries specifies the maximum number of rows supported in the tmnxEhsTriggerTable.

OBJECT-TYPE

The value of the object tmnxEhsTEntryTblLastChange indicates the value of sysUpTime at the time of the last modification of a row entry in the tmnxEhsTEntryTable.

OBJECT-TYPE

The value of the object tmnxEhsTEntryMaxEntries specifies the maximum number of row entries supported in the tmnxEhsTEntryTable.

OBJECT-TYPE

The tmnxEhsHandlerTable contains a list of Event Handlers used by the Event Handling System (EHS) Event Triggers.

OBJECT-TYPE

Defines a row entry in the tmnxEhsHandlerTable. Each entry contains information about a specific Event Handling System (EHS) Event Handler. Rows are created and deleted via SNMP SET operations using tmnxEhsHandlerRowStatus.

OBJECT-TYPE

The value of tmnxEhsHandlerName specifies the name of an Event Handling System (EHS) Event Handler represented by this row in the tmnxEhsHandlerTable.

OBJECT-TYPE

The value of tmnxEhsHandlerRowStatus specifies the row status. It allows rows to be created and deleted in the tmnxEhsHandlerTable. If any associated rows exist in the tmnxEhsHEntryTable, 'destroy' will fail. All associated rows must be destroyed first.

OBJECT-TYPE

The value of tmnxEhsHandlerDescription specifies a user provided description string for an EHS Handler. It can consist of any printable, seven-bit ASCII characters up to 80 characters in length.

OBJECT-TYPE

The value of tmnxEhsHandlerLastChange indicates the time this row entry was last changed.

OBJECT-TYPE

The value of tmnxEhsHandlerAdminStatus specifies the administrative state of the EHS Event Handler.

OBJECT-TYPE

The value of tmnxEhsHandlerOperStatus indicates the operational state of the EHS Event Handler.

OBJECT-TYPE

The tmnxEhsHandlerStatsTable contains operational data for Event handlers used by the EHS Event Triggers.

OBJECT-TYPE

Defines a row in the tmnxEhsHandlerStatsTable. Each row contains operational information about a specific EHS Event Handler. Rows are created and deleted by the system as rows are created and deleted in the tmnxEhsHandlerTable.

OBJECT-TYPE

The value of tmnxEhsHandlerStatsSuccess indicates the number of times the EHS system triggers a handler, which can take corresponding action specified in handler's entries

OBJECT-TYPE

The value of tmnxEhsHandlerStatsErrNoEntry indicates the number of times the EHS system triggers a handler, which can not take corresponding action as there is no handler's entry specifying an operation to perform.

OBJECT-TYPE

The value of tmnxEhsHandlerStatsErrAdmStatus indicates the number of times the EHS system triggers a handler, which can not take corresponding action due to admin state of the handler. The handler may be out-of-service due to tmnxEhsHandlerAdminStatus being set to 'outOfService (3)'.

OBJECT-TYPE

The tmnxEhsHEntryTable contains a list of Event Handler Entries in an EHS Event Handler.

OBJECT-TYPE

Defines a row in the tmnxEhsHEntryTable. Each row contains information about a specific Handler Entry. Rows are created and deleted via SNMP SET operations using tmnxEhsHEntryRowStatus.

OBJECT-TYPE

The value of tmnxEhsHEntryId specifies the index of an Event Entry in the EHS Event Handler indicated by the value of tmnxEhsHandlerName.

OBJECT-TYPE

The value of tmnxEhsHEntryRowStatus specifies the row status. It allows rows to be created and deleted in the tmnxEhsHEntryTable. If an associated row does not exist in the tmnxEhsHandlerTable, a attempt to create a row will fail.

OBJECT-TYPE

The value of tmnxEhsHEntryDescription specifies a user provided description string for EHS Event Handler Entry. It can consist of any printable, seven-bit ASCII characters up to 80 characters in length.

OBJECT-TYPE

The value of tmnxEhsHEntryLastChange indicates the time this row was last changed.

OBJECT-TYPE

The value of tmnxEhsHEntryAdminStatus specifies the administrative state of the EHS Event Handler Entry.

OBJECT-TYPE

The value of tmnxEhsHEntryOperStatus indicates the operational state of the EHS Event Handler Entry.

OBJECT-TYPE

The value of tmnxEhsHEntryScriptPlcyName in combination with the value of tmnxEhsHEntryScriptPlcyOwner specifies the script policy that can be launched from this tmnxEhsHEntryTable row. The zero-length string may be used to point to a non-existing script policy.

OBJECT-TYPE

The value of tmnxEhsHEntryScriptPlcyOwner in combination with the value of tmnxEhsHEntryScriptPlcyName specifies the script policy that can be launched from this tmnxEhsHEntryTable row. The zero-length string may be used to point to a non-existing script policy.

OBJECT-TYPE

The value of tmnxEhsHEntryMinDelay specifies the minimum time, in seconds, between executions of the script policy specified by this EHS Event Handler Entry. A '0' value means no delay is imposed.

OBJECT-TYPE

The value of tmnxEhsHEntryLastExecuted indicates the time when handler entry launch execution of action.

OBJECT-TYPE

The tmnxEhsHEntryStatsTable contains operational data for Event Handler Entries used by an EHS Event Handler.

OBJECT-TYPE

Defines a row entry in the tmnxEhsHEntryStatsTable. Each row contains operational information about a specific EHS Event Handler Entry. Rows are created and deleted by the system as rows are created and deleted in the tmnxEhsHEntryTable.

OBJECT-TYPE

The value of tmnxEhsHEntryStatsLaunchSuccess indicates the number of successfully queued scripts by EHS handler entry.

OBJECT-TYPE

The value of tmnxEhsHEntryStatsErrMinDelay indicates the number of cancelled script executions due to tmnxEhsHEntryMinDelay.

OBJECT-TYPE

The value of tmnxEhsHEntryStatsErrLaunch indicates the number of cancelled script executions due to launch failure.

OBJECT-TYPE

The value of tmnxEhsHEntryStatsErrAdmStatus indicates the number of cancelled script executions due to admin state of the handler entry. The handler entry may be out-of-service due to tmnxEhsHEntryAdminStatus being set to 'outOfService (3)'.

OBJECT-TYPE

The tmnxEhsTriggerTable contains a list of Event Triggers used by the Event Handling System (EHS).

OBJECT-TYPE

Defines a row in the tmnxEhsTriggerTable. Each row contains information about a specific Event Handling system (EHS) Event Trigger. Rows are created and deleted via SNMP SET operations using tmnxEhsTriggerRowStatus.

OBJECT-TYPE

The value of tmnxEhsTriggerRowStatus specifies the row status. It allows rows to be created and deleted in the tmnxEhsTriggerTable. If any associated rows exist in the tmnxEhsTEntryTable, 'destroy' will fail with an 'inconsistentValue' error. All associated rows in the tmnxEhsTEntryTable must be destroyed first.

OBJECT-TYPE

The value of tmnxEhsTriggerDescription specifies a user provided description string for an EHS Event Trigger. It can consist of any printable, seven-bit ASCII characters up to 80 characters in length.

OBJECT-TYPE

The value of tmnxEhsTriggerLastChange indicates the time this row was last changed.

OBJECT-TYPE

The value of tmnxEhsTriggerAdminStatus specifies the administrative state of the EHS Event Trigger.

OBJECT-TYPE

The value of tmnxEhsTriggerOperStatus indicates the operational state of the EHS Event Trigger.

OBJECT-TYPE

The tmnxEhsTriggerStatsTable contains operational data for Event Triggers used by the Event Handling System (EHS).

OBJECT-TYPE

Defines a row in the tmnxEhsTriggerStatsTable. Each row contains operational information about a specific EHS Event Trigger. Rows are created and deleted by the system as rows are created and deleted in the tmnxEhsTriggerTable.

OBJECT-TYPE

The value of tmnxEhsTriggerStatsSuccess indicates the number of not ignored logger event occurrences associated with EHS trigger.

OBJECT-TYPE

The value of tmnxEhsTriggerStatsErrNoEntry indicates the number of ignored logger event occurrences associated with EHS trigger. Event is ignored due to no trigger entry configured for this trigger.

OBJECT-TYPE

The value of tmnxEhsTriggerStatsErrAdmStatus indicates the number of ignored logger event occurrences associated with EHS trigger. Event is ignored due to admin state of the trigger. The trigger may be out-of-service due to tmnxEhsTriggerAdminStatus being set to 'outOfService (3)'.

OBJECT-TYPE

The tmnxEhsTEntryTable contains a list of Event Trigger Entries in an EHS Event Trigger.

OBJECT-TYPE

Defines a row in the tmnxEhsTEntryTable. Each row contains information about a specific EHS Event Trigger Entry. Rows are created and deleted via SNMP SET operations using tmnxEhsTEntryRowStatus.

OBJECT-TYPE

The value of tmnxEhsTEntryId specifies the index of a Trigger Entry in the EHS Event Trigger indicated by the value of tmnxEventAppIndex and tmnxEventID.

OBJECT-TYPE

The value of tmnxEhsTEntryRowStatus specifies the row status. It allows entries to be created and deleted in the tmnxEhsTEntryTable. If an associated row does not exist in the tmnxEhsTriggerTable, an attempt to create this row entry will fail.

OBJECT-TYPE

The value of tmnxEhsTEntryDescription specifies a user provided description string for EHS Event Trigger Entry. It can consist of any printable, seven-bit ASCII characters up to 80 characters in length.

OBJECT-TYPE

The value of tmnxEhsTEntryLastChange indicates the time this row entry was last changed.

OBJECT-TYPE

The value of tmnxEhsTEntryAdminStatus specifies the administrative state of the EHS Event Trigger Entry.

OBJECT-TYPE

The value of tmnxEhsTEntryOperStatus indicates the operational state of the EHS Event Trigger Entry.

OBJECT-TYPE

The value of tmnxEhsTEntryLogFilterId specifies the logger filter to apply to a generated logger event. If the logger filter match succeeds, the actions indicated in the associated EHS Event Handler, indicated by the value of tmnxEhsTEntryHandlerName, are applied. A value of 0 indicates there is no associated logger filter and therefore the associated EHS Event Handler is always applied.

OBJECT-TYPE

The value of tmnxEhsTEntryHandlerName specifies the EHS Event Handler to be applied. The zero-length string may be used to point to a non-existing Event Handler.

OBJECT-TYPE

The value of tmnxEhsTEntryDebounceVal specifies the number of times an event has to occur within a specific time window given by tmnxEhsTEntryDebounceTime for EHS Event to trigger a response.

OBJECT-TYPE

The value of tmnxEhsTEntryDebounceTime specifies the time window within which a specific event must occur more than the value specified by tmnxEhsTEntryDebounceVal for EHS to trigger a response.

OBJECT-TYPE

The Nokia SROS series tmnxEhsTEntryStatsTable contains operational data for Event Trigger Entries used by an EHS Event Trigger.

OBJECT-TYPE

Defines a row in the tmnxEhsTEntryStatsTable. Each row contains operational information about a specific EHS Event Trigger Entry. Rows are created and deleted by the system as row are created and deleted in the tmnxEhsTEntryTable.

OBJECT-TYPE

The value of tmnxEhsTEntryStatsFilterMatch indicates the number of times a filter, for the specified trigger entry, matches an logger event.

OBJECT-TYPE

The value of tmnxEhsTEntryStatsFilterFail indicates the number of times a filter, for the specified trigger entry, does not match an logger event.

OBJECT-TYPE

The value of tmnxEhsTEntryStatsErrAdminStatus indicates the number of times the logger event will be ignored due to admin state of EHS trigger entry. The trigger entry may be out-of-service due to tmnxEhsTEntryAdminStatus being set to 'outOfService (3)'.

OBJECT-TYPE

The value of tmnxEhsTEntryStatsErrFilter indicates the number of times the logger event will be ignored due to filter is not operational or is not configured in EHS trigger entry.

OBJECT-TYPE

The value of tmnxEhsTEntryStatsErrHandler indicates the number of times the logger event will be ignored due to filter is not operational or is not configured in EHS trigger entry.

OBJECT-TYPE

The value of tmnxEhsTEntryStatsTriggerCount indicates the number of times script execution is triggered after filter match.

OBJECT-TYPE

The value of the tmnxEhsTEntryStatsDebounce indicates the number of times script is not executed due to debounce rule.

OBJECT-TYPE

The tmnxLogCliSubscrTable contains information about CLI user session subscriptions to logs.

OBJECT-TYPE

Each conceptual row represents information about a subscription of a particular CLI user session to a particular log. Entries in this table are created and destroyed automatically by the system.

OBJECT-TYPE

The value of the object tmnxLogCliSubscrSession indicates the unique identifier of a CLI user session.

OBJECT-TYPE

The value of tmnxLogCliSubscrLog indicates the unique identifier of an event stream log. It refers to a conceptual row in the tmnxLogIdTable.

OBJECT-TYPE

The value of the object tmnxLogCliSubscrType indicates the type of session.

OBJECT-TYPE

The value of the object tmnxLogCliSubscrUser indicates the name of the user associated with the CLI session.

OBJECT-TYPE

The value of tmnxLogCliSubscrUserLoginTime indicates the time the user logged in.

OBJECT-TYPE

The value of tmnxLogCliSubscrUserIpAddrType indicates the address type of tmnxLogCliSubscrUserIpAddr.

OBJECT-TYPE

The value of the object tmnxLogCliSubscrUserIpAddr indicates the IP address of the user.

OBJECT-TYPE

The Nokia SROS series tmnxLogApCustRecordPolicerTable allows to create custom record policer information for a given accounting policy. Rows can only be created for existing accounting policies (as defined in tmnxLogApTable).

OBJECT-TYPE

A conceptual row contains the specification of the counters that must be collected for a particular policer and accounting policy. A conceptual row can be created and destroyed by means of the tmnxLogApCrPolicerRowStatus object.

OBJECT-TYPE

The value of tmnxLogApCrPolicerId specifies the policer ID for which counters will be collected in this custom record. The counters that will be collected are defined in tmnxLogApCrPolicerICounters and tmnxLogApCrPolicerECounters.

OBJECT-TYPE

The value of tmnxLogApCrPolicerLastChanged indicates the sysUpTime when an object in this table was last modified. A value of zero means that no change was made to this row since it was created.

OBJECT-TYPE

Row Status of the entry. This allows creation/deletion of rows in this table.

OBJECT-TYPE

The value of tmnxLogApCrPolicerICounters specifies the list of ingress counters that need to be collected in this custom record.

OBJECT-TYPE

The value of tmnxLogApCrPolicerECounters specifies the list of egress counters that need to be collected in this custom record.

OBJECT-IDENTITY

OBJECT-IDENTITY