RAPID-CITY

TEXTUAL-CONVENTION

An identifier that identifies the Bridge Id

TEXTUAL-CONVENTION

Possible values returned in the egress action field

TEXTUAL-CONVENTION

Possible values returned in the ingress action field.

TEXTUAL-CONVENTION

Possible values the Relay action field can take.

TEXTUAL-CONVENTION

Standard card states for slotted chassis based products

TEXTUAL-CONVENTION

802.1p Values

TEXTUAL-CONVENTION

QOS Drop Precedence

TEXTUAL-CONVENTION

DSCP Values

TEXTUAL-CONVENTION

Enable/Disable value.

TEXTUAL-CONVENTION

An identifier for a list of Ids.

TEXTUAL-CONVENTION

Port IfIndex.

TEXTUAL-CONVENTION

This textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits the additional value of zero. the value zero is object-specific and must therefore be defined as part of the description of any object which uses this syntax. Examples of the usage of zero might include situations where interface was unknown, or when none or all interfaces need to be referenced.

TEXTUAL-CONVENTION

The origin of the address. manual(2) indicates that the address was manually configured to a specified address, e.g. by user configuration. dhcp(4) indicates an address that was assigned to this system by a DHCP server. linklayer(5) indicates an address created by IPv6 stateless auto-configuration. random(6) indicates an address chosen by the system at random, e.g. an IPv4 address within 169.254/16, or an RFC 3041 privacy address.

TEXTUAL-CONVENTION

The status of an address. Most of the states correspond to states from the IPv6 Stateless Address Autoconfiguration protocol [5]. The preferred(1) state indicates that this is a valid address that can appear as the destination or source address of a packet. The deprecated(2) state indicates that this is a valid but deprecated address that should no longer be used as a source address in new communications, but packets addressed to such an address are processed as expected. The invalid(3) state indicates that this isn't a valid address and it shouldn't appear as the destination or source address of a packet. The inaccessible(4) state indicates that the address is not accessible because the interface to which this address is assigned is not operational. The unknown(5) state indicates that the status can not be determined for some reason. The tentative(6) state indicates the uniqueness of the address on the link is being verified. Addresses in this state should not be used for general communication and should only be used to determine the uniqueness of the address. The duplicate(7) state indicates the address has been determined to be non-unique on the link and so must not be used. In the absence of other information, an IPv4 address is always preferred(1).

TEXTUAL-CONVENTION

Plsb Node Nick name.

TEXTUAL-CONVENTION

The ipv6 next header to look for.

TEXTUAL-CONVENTION

Integer sub-range for default metric for single hop. ISO 10589 provides for 4 types of metric. Only the 'default' metric is used in practice.

TEXTUAL-CONVENTION

ISIS B-VLAN ID.

TEXTUAL-CONVENTION

ISIS B-VLAN tie breaking algorithm.

TEXTUAL-CONVENTION

Plsb Node Nick name.

TEXTUAL-CONVENTION

A system ID.

TEXTUAL-CONVENTION

Wide Metric for IS Neighbors. ISO 10589 provides a 6 bit metric. Traffic Engineering extensions provide 24 bit metrics.

TEXTUAL-CONVENTION

The string is 8 octets long, for a total of 64 bits. Each bit corresponds to a lane. Each I/O slot can have 4 or 6 lanes based on the card type. When a bit has the value one(1), the corresponding lane is a member of the set. When a bit has the value zero(0), the corresponding lane is not a member of the set. The encoding is such that the most significant bit of octet #1 corresponds to laneId 0, while the least significant bit of octet #8 corresponds to laneId 63. LaneIds 60, 61, 62, and 63 are not used for CB release 1.

TEXTUAL-CONVENTION

The set of lanes that are members of this Global Policer. The string is 4 octets long, for a total of 32 bits. Each bit corresponds to a laneId. Each I/O slot has 4 laneIds. When a bit has the value one(1), the corresponding laneId is a member of the set. When a bit has the value zero(0), the corresponding laneId is not a member of the set. The encoding is such that the most significant bit of octet #1 corresponds to laneId 0, while the least significant bit of octet #4 corresponds to laneId 31.

TEXTUAL-CONVENTION

Mpls Exp Values

TEXTUAL-CONVENTION

The string is 88 octets long, for a total of 704 bits. Each bit corresponds to a port, as represented by its ifIndex value . When a bit has the value one(1), the corresponding port is a member of the set. When a bit has the value zero(0), the corresponding port is not a member of the set. The encoding is such that the most significant bit of octet #1 corresponds to ifIndex 0, while the least significant bit of octet #88 corresponds to ifIndex 703. In order to accommodate future uses of this the string has a max size of 255 bytes.

TEXTUAL-CONVENTION

QOS Levels

TEXTUAL-CONVENTION

The representation of a BGP AFI

TEXTUAL-CONVENTION

The representation of a BGP Identifier. BGP Identifiers are presented in the received network byte order. The BGP Identifier is displayed as if it is an IP address, even if it would be an illegal one.

TEXTUAL-CONVENTION

The representation of a BGP SAFI

TEXTUAL-CONVENTION

The semantics are identical to the standard DisplayString in RFC1213 and RFC2579, except for the longer length that is allowed with this TC.

TEXTUAL-CONVENTION

Range of VLAN IDs supported for application

TEXTUAL-CONVENTION

Each VLAN ID is stored as a bit in a mask. The most-significant (left-most) bit represents Vlan ID 1.

TEXTUAL-CONVENTION

The range of intervals in seconds that a routers hello must have not been seen before a neighbor declares the router down

TEXTUAL-CONVENTION

Mode of given Fast SE Device either BME or SE

TEXTUAL-CONVENTION

An identifier that identifies the timeout value.

TEXTUAL-CONVENTION

The values one might be able to configure for variables bounded by the Refresh Interval

TEXTUAL-CONVENTION

The purpose of a VPN-ID is to uniquely identify a VPN. The Global VPN Identifier format is: 3 octet VPN Authority, Organizationally Unique Identifier followed by 4 octet VPN index identifying VPN according to OUI

TEXTUAL-CONVENTION

Virtual Router Identifier. VRFID 0 is reserved for the Administrative VRF and cannot be used to create VRF's.

TEXTUAL-CONVENTION

This object represents Routing Protocol (RP) Triggers on a Virtual Router. The BITS represent an Action-code that specifies the action on the Routing Protocols. The actions are: initiate or shutdown. When encoding the RP using the BITS construct, the value is encoded as an OCTET STRING where the first bit (bit 0) is the highest bit of the octet. Bits 0-3 may be specified in any combination to allow multiple Routing Protocols to be acted on simultaneously or individually.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

This entity's IP address.

OBJECT-TYPE

This entity's subnet mask.

OBJECT-TYPE

This entity's broadcast address.

OBJECT-TYPE

When an SNMP message is received by this entity, the community string in the message is compared with this string first. If it matches, read-write access is granted to all items in the MIB. If it doesn't match, the rcSysCommReadWrite string is compared next.

OBJECT-TYPE

When an SNMP message is received by this entity, the community string in the message is compared with this string second. If it matches, read-write access is granted to all items in the MIB except community strings. (Community strings appear empty when read and return a no such name error when an attempt is made to write them.) If it doesn't match, the rcSysCommReadWriteLayer3 string is compared next.

OBJECT-TYPE

When an SNMP message is received by this entity, the community string in the message is compared with this string third. If it matches, read-only access is granted to all items in the MIB except community strings. (Community strings appear empty when read.) If it doesn't match, no access is granted, no response is sent back to the SNMP requester, and SNMP traps are sent to the SNMP trap receiver(s) if configured.

OBJECT-TYPE

Software version running on device

OBJECT-TYPE

Initiate a system action.

OBJECT-TYPE

Result from the last system action.

OBJECT-TYPE

Last management initiated configuration change since sysUpTime.

OBJECT-TYPE

Last management initiated VLAN configuration change since sysUpTime.

OBJECT-TYPE

Last management initiated statistics reset since sysUpTime.

OBJECT-TYPE

Buffer utilization as a percentage of the total amount of buffer space in the system. A high value indicates congestion.

OBJECT-TYPE

The largest buffer utilization since sysUpTime

OBJECT-TYPE

Timestamp for rcSysPeakBandwidth

OBJECT-TYPE

Total Non-volatile RAM in Kbytes

OBJECT-TYPE

Non-volatile RAM in use in Kbytes

OBJECT-TYPE

SysUpTime of the last time when NVRAM was written to. This could be a save of the system configuration or via a file transfer of a configuration file.

OBJECT-TYPE

SysUpTime of the last time when the standby NVRAM (on the back-up CPU board) was written to.

OBJECT-TYPE

Percentage of CPU utilization. This object is not supported on VSP. VSP uses rcKhiSlotCpuCurrentUtil

OBJECT-TYPE

Percentage of Switching Fabric utilization. Object is not support on VSP

OBJECT-TYPE

Amount of RAM in bytes to allocate for RMON to use when rcSysRmonEnable is TRUE.

OBJECT-TYPE

Control whether the RMON feature should be enabled. To enable the RMON feature, set this variable to true. The RMON agent in the device will get started immediately if the amount of memory specified by rcSysRmonMemSize is currently available in the device. To disable the RMON feature, set this variable to false, save the new setting to NVRAM, and reboot the device. After the device is rebooted the RMON agent will not be operational.

OBJECT-TYPE

Control whether RMON configuration information should be saved to NVRAM so RMON settings can be automatically reinstalled after a system reboot. Setting rcSysRmonSaveConfig to true does not immediately save the configuration information. The save happens when the rcSysAction variable is set to 'saveToNVRAM(4)'. This option is only meaningful when the rcSysRmonEnable variable is set to true.

OBJECT-TYPE

Used to indicate whether RMON traps should be sent to only the owner of the RMON alarm (i.e., the manager that created the alarm entry) or all trap recipients in the system trap receiver table.

OBJECT-TYPE

Used to indicate whether routing is supported in this product.

OBJECT-TYPE

Used to indicate whether WebServer is supported in this product.

OBJECT-TYPE

Last management initiated IP address change since sysUpTime. Any addition or deletion of an IP address to a single routable port or a VLAN is time-stamped by this variable.

OBJECT-TYPE

When an SNMP message is received by this entity, the community string in the message is compared with this string third. If it matches, read-write access is granted to all Layer-3 items in the MIB except community strings. (Community strings appear empty when read and return a no such name error when an attempt is made to write them.) If it doesn't match, the rcSysCommReadWriteLayer2 string is compared next.

OBJECT-TYPE

When an SNMP message is received by this entity, the community string in the message is compared with this string fourth. If it matches, read-write access is granted to all Layer-2 items in the MIB except community strings. (Community strings appear empty when read and return a no such name error when an attempt is made to write them.) If it doesn't match, the rcSysCommReadOnly string is compared next.

OBJECT-TYPE

Used to configure the system access policy feature. if 'true', the rcSysAccessPolicyTable is examined to determine which packets should be allowed or denied access to this device.

OBJECT-TYPE

default config.

OBJECT-TYPE

default boot config.

OBJECT-TYPE

File name used in conjunction with rcSysAction. If rcSysAction is set to 'saveRuntimeConfig' or 'saveRuntimeConfigToSlave' then this file name will be used instead of the file name specified in rcSysDefaultRuntimeConfigFileName. If rcSysAction is set to 'saveBootConfig' or 'saveBootConfigToSlave' then this file name will be used insteaad of the file name specified in rcSysDefaultBootConfigFileName. If the file name is blank (i.e., nothing is entered) then the default file name will be used.

OBJECT-TYPE

SysUpTime of the last time when the run time configuration was written to.

OBJECT-TYPE

SysUpTime of the last time when the run time configuration was written to slave NVRAM.

OBJECT-TYPE

SysUpTime of the last time when the boot configuration was written to.

OBJECT-TYPE

SysUpTime of the last time when the boot configuration was written on the slave NVRAM.

OBJECT-TYPE

Used to control whether RMON should use a half-duplex or full-duplex formula to calculate port utilization. When set to 'halfDuplex', RMON will use InOctets and the port's speed to calculate port utilization (this is the standard RMON rfc1271 convention). When set to 'fullDuplex', RMON will use InOctets and OutOctets and 2X the port's speed to calculate port utilization. Furthermore, if this variable is set to 'fullDuplex', but the port is operating in a half-duplex mode, the calculation defaults back to the rfc1271 convention.

OBJECT-TYPE

read-write L1 access

OBJECT-TYPE

bw currently consumed

OBJECT-TYPE

peak bw since reset

OBJECT-TYPE

timestamp for rcSysPeakBw

OBJECT-TYPE

% cpu utilization

OBJECT-TYPE

% switch fabric util

OBJECT-TYPE

Dram size in mega-bytes. It is not supported on VSP

OBJECT-TYPE

Dram used in percentage. It is not supported on VSP

OBJECT-TYPE

Dram free size in kilo-bytes. It is not supported on VSP

OBJECT-TYPE

Dram max block free size in kilo-bytes. it is not supported on VSP

OBJECT-TYPE

Virtual IP is an IP address that owned and advertised only by the master CPU. So whichever CPU is master registers this IP address. Unlike the management IP address, this address goes in the switch config file and not the boot config

OBJECT-TYPE

Net mask of the management virtual Ip address

OBJECT-TYPE

The status of the read/write level

OBJECT-TYPE

This is the maximum transmission size of frames that all the ports on the chassis support.

OBJECT-TYPE

Time interval at which RTC and system clocks are synchronized.Not supported in VSP 3.3

OBJECT-TYPE

This is a flag that if user wants to configured CLIP (Circuit Less IP) as trap originator.

OBJECT-TYPE

enable or disable mroute stream limit in system.

OBJECT-TYPE

The trap receiver table (0 to 25 entries). This table lists the addresses of Network Management Stations that should receive trap messages from this entity when an exception condition occurs.

OBJECT-TYPE

A trap receiver table entry.

OBJECT-TYPE

IP address for trap receiver.

OBJECT-TYPE

The version of trap receiver.

OBJECT-TYPE

Community string used for trap messages to this trap receiver.

OBJECT-TYPE

Source IP address to use when sending traps. This IP address will be inserted into the source IP address field in the UDP trap packet.

OBJECT-TYPE

Used to create/delete entries

OBJECT-TYPE

Management access policy table. This table is used to permit or deny access to this device via the specified source Id.

OBJECT-TYPE

An access policy table entry.

OBJECT-TYPE

Policy Id.

OBJECT-TYPE

Name of this policy.

OBJECT-TYPE

Indicate whether this policy is currently active.

OBJECT-TYPE

Used to indicate whether a packet having a source IP address that matches this entry should be permitted to enter the device or denied access.

OBJECT-TYPE

Is represented as bitset to indicate which protocol this entry should be applied to. Value is one of multiple(logical 'OR') of the following values: telnet(1), snmp(2), tftp(4), ftp(8), http(16), rlogin(32), ssh(64), snmp-v3(128) telnet(1): enables telnet service snmp(2): enables snmp service tftp(4): enables tftp service ftp(8): enables ftp service http(16): enables http service rlogin(32): enables rlogin service ssh(64): enables ssh service snmp-v3(128): enables snmp service for v3 groups Value 0 means no service enabled.

OBJECT-TYPE

Used to indicate the precedence of this policy. The Lower the number the higher the precedence.

OBJECT-TYPE

Source network IP address.

OBJECT-TYPE

Source network mask.

OBJECT-TYPE

Trusted IP address of host performing a rlogin into the device.

OBJECT-TYPE

User name on the trusted host performing a rlogin into the device.

OBJECT-TYPE

Access level of trusted host.

OBJECT-TYPE

Used to indicate whether logging should be performed if this policy was applied.

OBJECT-TYPE

Usage Counter

OBJECT-TYPE

Used to create/delete an entry

OBJECT-TYPE

Used to restrict the access level specified in the system access policy table to exactly the same access level as specified by user. If TRUE then only the access level in the policy table is allowed access. If FALSE, then the default behavior is to assume the access level specified in policy table as the floor.

OBJECT-TYPE

Source network Inet Address Type.

OBJECT-TYPE

Source network Inet Address (prefix/network).

OBJECT-TYPE

Source network Inet Address Prefix-Length/Mask.

OBJECT-TYPE

Trusted Inet address of host performing a rlogin into the device.

OBJECT-TYPE

The trap sender table (0 to 25 entries). This table lists the addresses of Network Management Stations and the Source Address that should receive trap messages from this entity when an exception condition occurs.

OBJECT-TYPE

A trap sender table entry.

OBJECT-TYPE

IP address for trap receiver.

OBJECT-TYPE

IP address for trap sender.

OBJECT-TYPE

DNS serever list table used to store the details of the DNS server configured.

OBJECT-TYPE

table entry.

OBJECT-TYPE

Type of the DNS server

OBJECT-TYPE

IP address of the DNS server

OBJECT-TYPE

Status of DNS server

OBJECT-TYPE

Number of request send to this server

OBJECT-TYPE

Number of request send to this server which are successful

OBJECT-TYPE

Used to create/delete DNS server entries in rcSysDnsServerListTable.

OBJECT-TYPE

The address type of DNS Server.

OBJECT-TYPE

The address of the DNS Server

OBJECT-TYPE

DNS Host table.

OBJECT-TYPE

table entry.

OBJECT-TYPE

Host Name or Host IP Address.

OBJECT-TYPE

Host Name.

OBJECT-TYPE

Host IP Address.

OBJECT-TYPE

DNS Server IP or /etc/host file.

OBJECT-TYPE

Address Type of the Host.

OBJECT-TYPE

Address of the Host.

OBJECT-TYPE

Used to specify the maximum frequency/count of the occurence of the Log Message.

OBJECT-TYPE

A textual string containing the first four characters of the Log Message.

OBJECT-TYPE

Flag to decide if IP header source address will be matched with SNMP header sender networks.

OBJECT-TYPE

Default domain used for querying the DNS Server.

OBJECT-TYPE

DNS server's IP address

OBJECT-TYPE

DNS Type: Whether it was Dns Request or a Response

OBJECT-TYPE

This object indicates the current spanning-tree mode of the system. The meaning of specific values is: nortelStpg(1) .. The older proprietary mode which supports multiple spanning tree groups. pvst(2) ..Emulation of C***O spanning tree mode rstp(3) ..IEEE 802.1w mode mstp(4) ..IEEE 802.1s mode .

OBJECT-TYPE

This object indicates the desired spanning-tree mode of the system. The meaning of specific values is: nortelStpg(1) .. The older proprietary mode which supports multiple spanning tree groups. pvst(2) ..Emulation of C***O spanning tree mode rstp(3) ..IEEE 802.1w mode mstp(4) ..IEEE 802.1s mode . Note that depending on the current value of rcSysSpanningTreeOperMode and the value to which this object is set, the operational mode may be immediately changed, or the change may not take effect until the next system reboot.

OBJECT-TYPE

Time interval in seconds after which auto-recovery runs on ports to clear action taken by cp-limit, link flap or loop detect

OBJECT-TYPE

Time limit in milliseconds for MAC flapping for loop-detect feature

OBJECT-TYPE

Number of times mac flapping can happen for loop-detect feature

OBJECT-TYPE

enable or disable extended CP-LIMIT in system.

OBJECT-TYPE

Minimum time for which System octapid should be congested to trigger congestion algorithm for extended CP-LIMIT in mSecs

OBJECT-TYPE

Maximum number of ports which need to be monitored for congestion in Extended CP-LIMIT

OBJECT-TYPE

Minimum time for which ingress traffic utilization rate of a monitored port should stay more than the allowed limits in order to disable the port for extended CP-LIMIT in Secs

OBJECT-TYPE

Indicates the trap level for extended CP-LIMIT

OBJECT-TYPE

Indicates whether system octapid congestion detected for extended cp-limit

OBJECT-TYPE

Indicates whether ports has been shutdown due to extended cp-limit

OBJECT-TYPE

Indicates whether ports has been shutdown due to extended Cp-limit

OBJECT-TYPE

Initiate a system action for layer1 user

OBJECT-TYPE

Initiate a system action for layer2 user

OBJECT-TYPE

Initiate a system action for layer3 user

OBJECT-TYPE

Initiate a system action.

OBJECT-TYPE

The current power usage for the whole chassis.

OBJECT-TYPE

The current power available for the whole chassis.

OBJECT-TYPE

Management Force-msg Control table. This table is used to specify the pattern for Force-msg Control

OBJECT-TYPE

A Force-msg Control table entry.

OBJECT-TYPE

Pattern Id.

OBJECT-TYPE

Pattern for filtering the force-msg for msg control

OBJECT-TYPE

Used to create/delete an entry

OBJECT-TYPE

SNMP group list for access policy

OBJECT-TYPE

The table entry which covers the groups under snmp service.

OBJECT-TYPE

The snmp-v3 group name

OBJECT-TYPE

The snmp model

OBJECT-TYPE

Row status

OBJECT-TYPE

Virtual IP is an IP address that owned and advertised only by the master CPU. So whichever CPU is master registers this IP address.

OBJECT-TYPE

The length of the virtual ipv6 addr prefix (in bits).

OBJECT-TYPE

This is used in conjunction with rcSysAction inorder to decide the mode in which the config file is going to be saved in.

OBJECT-TYPE

This indicates days left before License Trial Period will expire.

OBJECT-TYPE

File name used in conjunction with rcSysAction. This file name will be used to specify a PLDS License file

OBJECT-TYPE

The total power for the whole chassis.

OBJECT-TYPE

Used to indicate the redundant power on the chassis. The redundant power is per power supply unit

OBJECT-TYPE

Used to enable/disable the trap send for authenticaion success trap rcnAuthenticationSuccess. It only allow to be set when snmpEnableAuthenTraps is enabled. I will be set to disable when snmpEnableAuthenTraps is disabled

OBJECT-TYPE

Used to enable/disable virtual ip as udp source.

OBJECT-TYPE

A list of software releases added to the switch. Maximum of 6 added releases can be present in the switch.

OBJECT-TYPE

Defines a row of rcSysSoftware Table using RcSysSoftwareEntry Type.

OBJECT-TYPE

Software Release Name

OBJECT-TYPE

Software Release Added Date and Time

OBJECT-TYPE

Software Release Activated Date and Time

OBJECT-TYPE

Software Release Committed Date and Time

OBJECT-TYPE

Software Release Committed Type

OBJECT-TYPE

Software Release Type. This element tells whether the release is a primary release for the switch or a backup release or that the release has been added to the switch but is not being used currently.

OBJECT-TYPE

Used to enable/disable data path fault shutdown.

OBJECT-TYPE

DNS server's IP address . Used by trap rcnDNSv6RequestResponseTrap

OBJECT-TYPE

Used to indicate the amount of power currently reserved on the system for critical cards that are present and other system critical modules such as cooling units.

OBJECT-TYPE

Used to indicate the maximum amount of power required on the system for all reserved and any additional cards that are present on the system to be powered on.

OBJECT-IDENTITY

OBJECT-TYPE

Name of source/destination host for the TFTP transfer.

OBJECT-TYPE

Name of file for the TFTP transfer.

OBJECT-TYPE

The action for the TFTP transfer.

OBJECT-TYPE

Contains result of the last Tftp action request.

OBJECT-IDENTITY

OBJECT-TYPE

The number of VLANs currently defined in the switch.

OBJECT-TYPE

A list of Virtual LAN entries. The number of entries is given by rcVlanNumVlans.

OBJECT-TYPE

Entry containing configuration information for a particular Virtual LAN. The relationship between the various port sets in a VLAN Entry are : o The set of ports defined by PortMembers must be a subset of the set of ports in the underlying STG of the VLAN. o The bitwise AND of PortMembers and NotAllowToJoin must be the empty set. o The bitwise OR of PortMembers and NotAllowToJoin must be the set of ports in the underlying STG of the VLAN. o The set of ports defined by StaticMembers must be a subset of the set of ports defined by PortMembers. o The bitwise XOR of PortMembers and StaticMembers defines the set of dynamic (potential) members of the VLAN. o The set of ports defined by ActiveMembers must be a subset of the set of ports defined by PortMembers.

OBJECT-TYPE

A value that uniquely identifies the Virtual LAN associated with this entry. This value corresponds to the lower 12 bits in the IEEE 802.1Q VLAN Tag.

OBJECT-TYPE

An administratively-assigned name for this VLAN.

OBJECT-TYPE

An administratively-assigned color code for this VLAN. The value of this object is used by the VLAN Manager GUI tool to select a color when it draws this VLAN on the screen.

OBJECT-TYPE

A flag to note whether frames in this VLAN should be assigned a high switching priority.

OBJECT-TYPE

A flag to note whether IP routing is enabled in this VLAN.

OBJECT-TYPE

When rcVlanRoutingEnable is set to true(1), this value indicates the 'logical' ifIndex assigned to this VLAN. Otherwise, this value is meaningless and should be set to zero.

OBJECT-TYPE

VLAN related actions.

OBJECT-TYPE

The result from the last VLAN action.

OBJECT-TYPE

Indicates the Spanning Tree Group (STG) used by this VLAN to determine the state of its ports. If this VLAN is not associated with any STG, this value should be set to zero.

OBJECT-TYPE

The type of VLAN, distinguished according to the policy used to define its port membership. VSP9000 does not support bySvlan(6) and ByIds(7).

OBJECT-TYPE

The set of ports that are members (static or dynamic) of this VLAN.

OBJECT-TYPE

The set of ports that are currently active in this VLAN. Active ports include all static ports and any dynamic ports where the VLAN policy was met.

OBJECT-TYPE

The set of ports that are static members of this VLAN. A static member of a VLAN is always active and is never aged out.

OBJECT-TYPE

The set of ports that are not allowed to become members of this VLAN.

OBJECT-TYPE

The protocol identifier of this VLAN. This value is meaningful only if rcVlanType is equal to byProtocolId(3). For other VLAN types it should have the value none(0).

OBJECT-TYPE

The IP subnet address of this VLAN. This value is meaningful only if rcVlanType is equal to byIpSubnet(2). For other VLAN types it should have the value 0.0.0.0.

OBJECT-TYPE

The IP subnet mask of this VLAN. This value is meaningful only if rcVlanType is equal to byIpSubnet(2). For other VLAN types it should have the value 0.0.0.0.

OBJECT-TYPE

The timeout period (in seconds) used for aging out dynamic members of this VLAN. This field is only relevant for policy-based VLANs.

OBJECT-TYPE

The MAC address assigned to the virtual router interface of this VLAN. This field is meaningful only if rcVlanRoutingEnable is equal to true(1).

OBJECT-TYPE

Used to create/delete entries in the rcVlanTable.

OBJECT-TYPE

A flag to note whether IGMP Snooping is enabled on this VLAN.

OBJECT-TYPE

A flag to note whether IGMP Report Proxy is enabled on this VLAN.

OBJECT-TYPE

This variable allows tuning for the expected packet loss on a subnet. If a subnet is expected to be lossy, the Robustness variable may be increased. IGMP is robust to (Robustness - 1) packet losses.

OBJECT-TYPE

The interval (in seconds) between IGMP Host-Query packets transmitted on this interface.

OBJECT-TYPE

The set of ports in this VLAN that provide connectivity to an IP Multicast router.

OBJECT-TYPE

When rcVlanProtocolId is set to usrDefined(15) in a protocol-based VLAN, this field represents the 16-bit user defined protocol identifier.

OBJECT-TYPE

Active ports.

OBJECT-TYPE

Bitfield of protocol ids.

OBJECT-TYPE

IP address of multicast querier router.

OBJECT-TYPE

Multicast querier router aging time out.

OBJECT-TYPE

The port on which the multicast querier router was heard.

OBJECT-TYPE

User priority level.

OBJECT-TYPE

Used to specify the Qos level packets, carried in this VLAN, should be processed with.

OBJECT-TYPE

Tos value.

OBJECT-TYPE

This is the encapsulation type for userdefined protocol based vlans. This is not meaningful for other types of vlan. The default value is null.

OBJECT-TYPE

This is the firewall vlan type for port based vlans.

OBJECT-TYPE

The timeout period (in seconds) used for aging out fdb entries of this VLAN.

OBJECT-TYPE

Firewall cluster Id

OBJECT-TYPE

The set of ports in the vlan that are designated as ospf passive

OBJECT-TYPE

NLB mode set on a VLAN.

OBJECT-TYPE

Indicates the Virtual Router to which the VLAN belongs

OBJECT-TYPE

The Name of the Virtual Router to which the VLAN belongs

OBJECT-TYPE

List of nodal Meps assigned to this vlan. A mep consists of Domain Name, Association name and Mep Id separated by '.'. Each meps is separated by ',': <md1>.<ma1>.<mepid1>,<md2>.<ma2>.<mepid2>,... The maximum number of nodal Mep for each vlan is 8.

OBJECT-TYPE

Number of nodal meps assigned to this vlan

OBJECT-TYPE

List of nodal Mip levels assigned to this vlan that allows Mip functionality to be enabled on a per level per vlan basis. A mip level is represented by an integer ranging from 0 to 7. The mip levels are separated by ',': <0...7>,<0...7>,... The maximum number of nodal Mip levels for each vlan is 8.

OBJECT-TYPE

Number of nodal mip levels assigned to this vlan that allows MIP functionality to be enabled on a per level per vlan basis.

OBJECT-TYPE

Plsb i-sid number assigned to a C-vlan or the i-sid value for primary private VLAN. Default 0 value indicates that no i-sid has been assigned.

OBJECT-TYPE

Indicate if the vlan is enabled for Remote Monitoring

OBJECT-TYPE

Indicate if the vlan is enabled for IPSEC. at place of this value use RcIpConfEntry for IPV4 and use RcIpv6InterfaceEntry for IPV6. This field changed to deprecated

OBJECT-TYPE

Enable/disable SPB multicast on Vlan

OBJECT-TYPE

A value that uniquely identifies the secondary Virtual LAN associated with the primary private VLAN. This value corresponds to the lower 12 bits in the IEEE 802.1Q VLAN Tag.

OBJECT-TYPE

Enable/disable PIM Gateway on Vlan

OBJECT-TYPE

Indicate if IPv6 DHCP snooping is enabled on the vlan

OBJECT-TYPE

Indicate if ND inspection is enabled on the vlan

OBJECT-TYPE

Enable/disable DVR on Vlan

OBJECT-TYPE

Gateway IPv4 address for this DVR enabled node on Vlan.

OBJECT-TYPE

The set of untagged ports that are members of this VLAN.

OBJECT-TYPE

A table used to maintain VLAN port related information.

OBJECT-TYPE

Entry containing VLAN information regarding a particular port.

OBJECT-TYPE

An unique index used to identify a particular port in the system. This index is equal to the ifIndex of the port.

OBJECT-TYPE

Used to indicate the number of VLAN IDs that are stored in the rcVlanPortVlanIds variable.

OBJECT-TYPE

An array used to identify which VLANs this port is assigned to. Each VLAN ID is stored as a two octet value. The first octet in the pair holds bits 15-8 of the VLAN ID, while the second octet holds bits 7-0 of the VLAN ID. This object is now replaced by rcVlanPortVlanIdList.

OBJECT-TYPE

The type of port: access(1) or trunk(2).

OBJECT-TYPE

A flag used to determine how to process tagged frames received on this access port. When the flag is set, these frames are discarded by the forwarding process. When the flag is reset, these frames are processed normally. This field is meaningless when the port is not an access port and should be set to false(2).

OBJECT-TYPE

A flag used to determine how to process untagged frames received on this trunk port. When the flag is set, these frames are discarded by the forwarding process. When the flag is reset, these frames are assigned to the VLAN specified by rcVlanPortDefaultVlanId. This field is meaningless when the port is not a trunk port and should be set to false(2).

OBJECT-TYPE

The VLAN ID assigned to untagged frames received on this trunk port. This field is meaningless when the port is not a trunk port.

OBJECT-TYPE

Enable/disable the port on the current vlan to perform tagging on the incoming and outgoing traffic.

OBJECT-TYPE

The type of port.

OBJECT-TYPE

Enable/disable loop detection on this port

OBJECT-TYPE

This value gives the IfIndex of the first port in the octapid. This value is used to generate an error message when changing port type from normal to uni/nni and viceversa

OBJECT-TYPE

This value gives the IfIndex of the first port in the octapid. This value is used to generate an error message when changing port type from normal to uni/nni and viceversa

OBJECT-TYPE

enable/disable Egress Tagging on the Default Vlan of the port.

OBJECT-TYPE

This value is used to specify the action which needs to be taken once a loop is detected on a specific port. VlanBlock is not supported in VSP9000.

OBJECT-TYPE

Enable/disable Arp detection on this port

OBJECT-TYPE

Enable/disable spoof detection on this port

OBJECT-TYPE

Enable/disable Subnet based Vlan packets on this port.

OBJECT-TYPE

Enable/disable Protocol based Vlan packets on this port.

OBJECT-TYPE

Sets the precedence for vlan classification. A value of 1 puts classification of packets to source mac vlans ahead of subnet based vlans. A value of 2 puts subnet based vlans ahead of source mac vlans. Classification to other types of vlans is unaffected as it occurs following source mac and subnet based vlans.

OBJECT-TYPE

This bitfield is used to identify which VLANs this port is assigned to. Each VLAN ID is stored as a bit. The most-significant (left-most) bit represents Vlan Id 1.

OBJECT-TYPE

Enable/disable SourceMac based Vlan packets on this port.

OBJECT-TYPE

The type of port associated with private VLAN. If the VLAN is not private then this is ignored. If the VLAN is private then the value must be either trunk, isolated, or promiscuous. Setting the value to trunk will enable tagging. Setting the value to isolated or promiscuous will remove non-private VLANs from the port.

OBJECT-TYPE

This object is used to identify which VLANs this port is associated with as untagged.

OBJECT-TYPE

A table used to maintain MAC addresses assigned to a particular VLAN by MAC address.

OBJECT-TYPE

Entry containing VLAN information regarding a particular port.

OBJECT-TYPE

An unique index used to identify a VLAN (by MAC address) in the system.

OBJECT-TYPE

An unique index used to identify a MAC address assigned to a particular VLAN.

OBJECT-TYPE

Row status for this entry.

OBJECT-TYPE

The number of entries (rows) in the rcVlanIgmpSnoopTable.

OBJECT-TYPE

The (conceptual) table listing the IP multicast groups for which there are members on a particular interface on a particular VLAN (i.e., a list known multicast receivers). A row is created by the system when it receives an IGMP Join messages on a port.

OBJECT-TYPE

An entry (row) in the rcVlanIgmpSnoopTable.

OBJECT-TYPE

The VLAN for which this entry contains information.

OBJECT-TYPE

The IP multicast group address for which this entry contains information.

OBJECT-TYPE

The interface for which this entry contains information for this IP multicast group address (i.e., the port the Join message was received).

OBJECT-TYPE

The IP Address of the source of the membership report received for this IP Multicast group address on this interface (i.e., the address of the host sending the Join message).

OBJECT-TYPE

The minimum amount of time remaining before this entry will be aged out.

OBJECT-TYPE

The type of entry: dynamic(1) entries are created by snooping IGMP messages, static(2) entries are created via management.

OBJECT-TYPE

The (conceptual) table listing the statically- defined IP multicast groups for which there are members on a particular interface on a particular VLAN.

OBJECT-TYPE

An entry (row) in the rcVlanIgmpSnoopStaticTable.

OBJECT-TYPE

The VLAN for which this entry contains information.

OBJECT-TYPE

The IP multicast group address for which this entry contains information. The address must fall within 224.0.1.0 to 239.255.255.255.

OBJECT-TYPE

The set of ports in this VLAN multicast traffic for the rcVlanIgmpSnoopStaticIpAddress is to be forwarded to.

OBJECT-TYPE

Used to create/delete entries in the rcVlanIgmpSnoopStaticTable.

OBJECT-TYPE

Not allowed to join

OBJECT-TYPE

Table used to specify which host(s) can send and/or receive IP Multicast traffic.

OBJECT-TYPE

An entry (row) in the rcVlanIgmpSnoopAccessTable.

OBJECT-TYPE

The VLAN for which this entry contains information.

OBJECT-TYPE

The IP multicast group address for which this entry contains information.

OBJECT-TYPE

The IP address of a host for which this entry contains information.

OBJECT-TYPE

The IP netmask of a host for which this entry contains information.

OBJECT-TYPE

Used to specify whether the host identified by rcVlanIgmpSnoopAccessHostAddr should be denied IP multicast transmit, receive, or both.

OBJECT-TYPE

Row status

OBJECT-TYPE

The (conceptual) table listing the IP multicast groups for which there are members on a particular interface on a particular VLAN (i.e., a list known multicast senders). A row is created by the system when it receives an IGMP Join messages on a port.

OBJECT-TYPE

An entry (row) in the rcVlanIgmpSnoopSenderTable.

OBJECT-TYPE

The VLAN for which this entry contains information.

OBJECT-TYPE

The IP multicast group address for which this entry contains information.

OBJECT-TYPE

The interface for which this entry contains information for this IP multicast group address (i.e., the port the multicast traffic was received).

OBJECT-TYPE

The IP Address of the host sending the multicast traffic.

OBJECT-TYPE

Used to specify an action to perform on this group.

OBJECT-TYPE

A list of Vlans the port belongs to and the corresponding loop detected status.

OBJECT-TYPE

Loop-Detected Entry.

OBJECT-TYPE

Port Number.

OBJECT-TYPE

Gives the VlanId to which the port belongs.

OBJECT-TYPE

Gives the Loop Detected status of the port in a vlan.

OBJECT-TYPE

A table used to maintain DSAP/SSAP values assigned to a sna802dot2 or userdefined vlan.

OBJECT-TYPE

An entry in the rcVlanDsapSsap table.

OBJECT-TYPE

A unique index to identify a vlan.

OBJECT-TYPE

Values of DSAP/SSAP assigned to a particular vlan.

OBJECT-TYPE

Row Status.

OBJECT-TYPE

A list of Vlans the port belongs to and the corresponding loop detected status.

OBJECT-TYPE

Loop-Detected Entry.

OBJECT-TYPE

Port Number.

OBJECT-TYPE

Gives the VlanId to which the port belongs.

OBJECT-TYPE

Mac address

OBJECT-TYPE

This value is used to specify the action which needs to be taken once a loop is detected on a specific port.

OBJECT-TYPE

A MAC address indicate for remote learnt, either local or remote.

OBJECT-TYPE

A table that can be used to map the Virtual LAN Id to IfIndex and Name for display. It is informational only.

OBJECT-TYPE

Each entry has mapping information for a particular Virtual LAN. This in intended for display purposes only.

OBJECT-TYPE

A value that uniquely identifies the Virtual LAN associated with this entry. This value corresponds to the lower 12 bits in the IEEE 802.1Q VLAN Tag.

OBJECT-TYPE

The assigned name for this VLAN.

OBJECT-TYPE

When rcVlanRoutingEnable is set to true(1), this value indicates the 'logical' ifIndex assigned to this VLAN. Otherwise, this value is meaningless and will be set to zero.

OBJECT-TYPE

A table contains a list of Spoof blocked MAC address information.

OBJECT-TYPE

Entry containing a spoof blocked MAC address

OBJECT-TYPE

Port interface number of the Spoof detect is enabled. Spoof mac is detected

OBJECT-TYPE

A vlan entry which the port intreface belong to. And the spoof MAC is detected

OBJECT-TYPE

A Local Ip address on this interface

OBJECT-TYPE

A spoofing Mac address that is detected in this interface

OBJECT-TYPE

Clear/delete this spoof detect mac entry when it is true. It always return false when query

OBJECT-IDENTITY

OBJECT-TYPE

Chassis Type

OBJECT-TYPE

Unique serial number for this chassis.

OBJECT-TYPE

Device hardware revision level

OBJECT-TYPE

The number of slots in the chassis available for plug-in cards.

OBJECT-TYPE

The total number of ports currently installed in the chassis.

OBJECT-TYPE

Chassis start-up diagnostic tests.

OBJECT-IDENTITY

OBJECT-TYPE

This table contains information about Fans

OBJECT-TYPE

Contains information regarding a Fan Unit

OBJECT-TYPE

The chassis fan Id.

OBJECT-TYPE

Actual status of the Fan: - unknown(1) - status can not be determined. - up(2) - present and supplying power. - down(3) - present, but failure indicated.

OBJECT-TYPE

Used to indicate the temperature in celsius of the air entering the fan.

OBJECT-TYPE

Type of the Fan: - unknown(1) - type can not be determined. - regularSpeed(2) - regular speed fan is present. - highSpeed(3) - high speed fan is present.

OBJECT-TYPE

Direction of the Fan Flow: - unknown(1) - Flow can not be determined. - fronttoback(2) - Front to back flow. - backtofront(3) - Back to front flow.

OBJECT-IDENTITY

OBJECT-TYPE

This table contains information about power supplies.

OBJECT-TYPE

Contains information regarding a power supply unit.

OBJECT-TYPE

The power supply Id.

OBJECT-TYPE

Actual status of the power supply: - unknown(1) - status can not be determined. - empty(2) - power supply not installed. - up(3) - present and supplying power. - down(4) - present, but failure indicated.

OBJECT-TYPE

This table contains detailed information about power supplies.

OBJECT-TYPE

Contains detailed info regarding a power supply unit.

OBJECT-TYPE

The power supply Id.

OBJECT-TYPE

The power supply type.

OBJECT-TYPE

The power supply serial number.

OBJECT-TYPE

The hardware revision of the power supply.

OBJECT-TYPE

The power supply part number.

OBJECT-TYPE

The detail description of power supply.

OBJECT-TYPE

The power supply Input Line voltage.

OBJECT-TYPE

The power supply Line voltage considered for Power Management calculation.

OBJECT-TYPE

The output power of this power supply

OBJECT-TYPE

The power supply Fan Flow Type.

OBJECT-IDENTITY

OBJECT-TYPE

A table that contains information about the cards in this chassis. For those slots that do not contain a physical card, the table may be implemented to contain a conceptual row with the type of physical module set to 'chasCardEmpty', or it may be implemented to have no conceptual row instance.

OBJECT-TYPE

Card attributes

OBJECT-TYPE

A unique value for each module within the chassis. This value is determined by the chassis slot number where the module is inserted. Valid entries are 1 to the value of rcChasNumSlots

OBJECT-TYPE

Used to indicate the card type. The value returned is defined by the description in rc2kCardTable.

OBJECT-TYPE

Unique serial number for this card.

OBJECT-TYPE

Hardware Version

OBJECT-TYPE

Used to indicate the administrative status of this card

OBJECT-TYPE

Used to indicate the operational status of this card.

OBJECT-TYPE

Used to indicate the type of PCMCIA card currently installed in this CPU card, if any. For non-CPU cards, this variable has no meaning and will always be set to none.

OBJECT-TYPE

Card Part Number

OBJECT-TYPE

Oxate CPLD version for CP card

OBJECT-TYPE

Oxide FGPA version for CP card

OBJECT-TYPE

Catskill FPGA version for CP card

OBJECT-TYPE

QE version for CP card

OBJECT-TYPE

K2 FPGA version for IO card

OBJECT-TYPE

IO Date DC CPLD for IO card

OBJECT-TYPE

IO Date BaseBoard CPLD for IO card

OBJECT-TYPE

IO PIM CPLD for IO card

OBJECT-TYPE

LED0 CPLD for IO card

OBJECT-TYPE

LED1 CPLD for IO card

OBJECT-TYPE

Zagros FPGA for IO card

OBJECT-TYPE

RSP for IO card

OBJECT-TYPE

BCM Mac for IO card

OBJECT-TYPE

Phosphide FPGA for IO card

OBJECT-TYPE

Sulfide FPGA for IO card

OBJECT-TYPE

Fluorate Cpld for SF card

OBJECT-TYPE

BME for SF card

OBJECT-IDENTITY

OBJECT-TYPE

Port table

OBJECT-TYPE

Entry containing info. for a particular port

OBJECT-TYPE

An index value that uniquely identifies a port. This value is similar to ifIndex in MIB2.

OBJECT-TYPE

Port type

OBJECT-TYPE

Type of connector installed on this port.

OBJECT-TYPE

Indicate whether this port should perform routing

OBJECT-TYPE

Indicate whether this port should be treated with high priority

OBJECT-TYPE

Port related actions.

OBJECT-TYPE

Result from the last Vlan action.

OBJECT-TYPE

For ports configured with redundant connectors, this value is used to indicate which connector should be used as the 'active' connector on this port the next time the port is placed into the ifAdminStatus=Up.

OBJECT-TYPE

For ports configured with redundant connectors, this value is used to indicate which connector is currently the active one. Only one connector can be active an anytime.

OBJECT-TYPE

Indicate the status of the link attached to the back-up (non-active) connector.

OBJECT-TYPE

Indicate whether this port enabled for auto negotiations or not.

OBJECT-TYPE

Indicates the port duplex type

OBJECT-TYPE

Indicate this port's current duplex value.

OBJECT-TYPE

Indicate this port's speed.

OBJECT-TYPE

Indicate this port's current speed value.

OBJECT-TYPE

Indicate which multi-link trunk (MLT) this port is assigned to. If this port is not associated with any MLT, this value will be set to zero(0).

OBJECT-TYPE

Indicate whether this port is locked.

OBJECT-TYPE

Indicate whether this port can support auto-negotiation.

OBJECT-TYPE

Indicate whether this port is a single routable port. If this value is true, the port functions like a traditional router port.

OBJECT-TYPE

If rcUnknownMacDiscard is set to True, then a packet with an unknown source MAC address is dropped on that port, and other ports then will discard any packets with this MAC address in the destination field. For example, suppose 11:22:33:44:55:66 is an unknown source MAC, packets with source MAC 11:22:33:44:55 coming from this port is discarded, further more, packets with destination MAC 11:22:33:44:55:66 coming from other ports are also discarded, unless this address is later learned on another port or the restriction ages out.

OBJECT-TYPE

# state transitions.

OBJECT-TYPE

User priority level.

OBJECT-TYPE

Used to specify whether over-size frames should be processed or dropped.

OBJECT-TYPE

Used to specify the Qos level packets, carried on this port, should be processed with.

OBJECT-TYPE

Used to enable/disable the Differentiated Service feature on this port.

OBJECT-TYPE

Used to specify the Differentiated Service type for this port.

OBJECT-TYPE

Used to enable/disable the Differentiated Service IEEE 802.1P over-ride feature.

OBJECT-TYPE

Used to show the name of the vendor of this port's connector. Only applicable to ports on a GBIC cards.

OBJECT-TYPE

This port's name.

OBJECT-TYPE

The octapid id of the mirrored port.

OBJECT-TYPE

Indicatie this port's current WAN/LAN mode. Valid for 10 GE only

OBJECT-TYPE

Indicatie this port's current tranport layer. Valid for 10 GE only

OBJECT-TYPE

Used to enable/disable the Telephony device selected on this port

OBJECT-TYPE

Used to set/get the selected Multimedia & Telephony Devices on this port. The String is the name of the device in the rcIpFilterMediaDevTable

OBJECT-TYPE

Indicate whether the port is routable.

OBJECT-TYPE

The status of the port whether is routable.

OBJECT-TYPE

The pid of the mirrored port.

OBJECT-TYPE

Used to enable/disable IEEE 802.1P override. If it is enabled, 802.1p value from a tagged frame may not be honored.

OBJECT-TYPE

A TRUE value indicates if CP Limit shut down the interface.

OBJECT-TYPE

Enable/Disable high secure feature.

OBJECT-TYPE

maximum number of multicast streams that are allowed to ingress to CPU through this port.

OBJECT-TYPE

sampling period to check number of multicast streams that has ingressed CPU through this port in seconds.

OBJECT-TYPE

enable or disable mroute stream limit on port.

OBJECT-TYPE

This object is used to specify the port speed and duplex abilities to be advertised during link negotiation. bit 0 - 10 half duplex advertised bit 1 - 10 full duplex advertised bit 2 - 100 half duplex advertised bit 3 - 100 full duplex advertised bit 4 - 1000 half duplex advertised bit 5 - 1000 full duplex advertised bit 6 - Mac PAUSE frame support advertised bit 7 - Asymmetric PAUSE frame support advertised bit 8 - No advertisements bit 9 - 10G full duplex advertisement bit 10 - Set advertise to default setting based on the hardware capability. bit 11 - 2,5G full duplex advertisement bit 12 - 5G full duplex advertisement The abilities specified in this object are only used when auto-negotiation is enabled on the port. If all bits in this object are disabled, and auto-negotiation is enabled on the port, then the physical link process on the port will be disabled (if hardware supports this ability). Any change in the value of this bit map will force the PHY to restart the auto-negotiation process. This will have the same effect as physically unplugging and reattaching the cable plant attached to this port. The capabilities being advertised are either all the capabilities supported by the hardware or the user- configured capabilities which is a subset of all the capability supported by hardware. The default value for this object will be all the capabilities supported by the hardware. Bit 10, default allowed user to set advertise to default. 'default' will take precedence if 'default' bit is combined with other bits. Note that bit 6 and bit 7 are currently not supported in ERS8600.

OBJECT-TYPE

enable or disable auto recovery of port from action taken by cp-limit, link flap or loop detect features

OBJECT-TYPE

Indicates the port configuration for extended CP-LIMIT

OBJECT-TYPE

Threshold for Ingress traffic utilization rate of the port for extended CP-LIMIT

OBJECT-TYPE

Egress Rate Limit. Different platform has different valid range. For VOSS product, Valid range is 1000..100000000, 0 means disabled. The maximum value is based on the port capability. Value of qos if-shaper

OBJECT-TYPE

Used to enable/disable shape/egress-rate-limit functionality. WHen it is disabled, rcPortEgressRateLimit will be set to 0

OBJECT-TYPE

The remaining time the port will be disabled due to a BPDU received when BPDU filtering is enabled.

OBJECT-TYPE

The time the port will be disabled when a BPDU is received when BPDU filtering is enabled.

OBJECT-TYPE

Used to enable/disable BPDU filtering.

OBJECT-TYPE

Indicates whether BPDU filtering is actually enabled or disabled.

OBJECT-TYPE

Used to enable/disable the control packet rate limit. Specifies whether or not rate limiting is currently in operation for multicast and broadcast packets for the specified port.

OBJECT-TYPE

Used to limit Multicast traffic on the specified port. Sets the limit in packets per second.

OBJECT-TYPE

Used to limit Broadcast traffic on the specified port. Sets the limit in packets per second.

OBJECT-TYPE

Indicates this port's current WAN clock source. Valid for 10 GE WAN only

OBJECT-TYPE

Limits the amount of traffic from this Ingress port. Value of qos if-rate-limite setting

OBJECT-TYPE

Used to enable/disable police/ingress-rate-limit functionality.

OBJECT-TYPE

The set of VRF ids to which this port belongs.

OBJECT-TYPE

User provided field. Used to give extra management information/data

OBJECT-TYPE

User provided additional field. Used to give extra management information/data

OBJECT-TYPE

The set of VRF names to which this port belongs.

OBJECT-TYPE

Gives the VRF Id for this Brouter port.

OBJECT-TYPE

Gives the VRF Name for this Brouter port.

OBJECT-TYPE

The total number of VRFs this port is associated to.

OBJECT-TYPE

Peak rate limit for this port. 0 means disable

OBJECT-TYPE

Service rate limit for this port. 0 mean disable

OBJECT-TYPE

Used to limit Control packets on the port to qos-levels 6 and 7. Sets the limit in packets per second.

OBJECT-TYPE

Used to indicate if the port should be shutdown when the CpLimitPktRate is exceeded.

OBJECT-TYPE

Used to set Remote Monitoring enable/disable

OBJECT-TYPE

Used to set IPSEC enable/disable. at place of this value use RcIpConfEntry for IPV4 and use RcIpv6InterfaceEntry for IPV6. This field changed to deprecated

OBJECT-TYPE

The port shutdown can happen due to many reason. It indicates the reason for the port state change.

OBJECT-TYPE

Used to set FLEX UNI enable/disable on port

OBJECT-TYPE

The remaining time the port will be disabled due to a BPDU received when BPDU guard is enabled.

OBJECT-TYPE

The time the port will be disabled when a BPDU is received when BPDU Guard is enabled.

OBJECT-TYPE

Used to enable/disable BPDU guard.

OBJECT-TYPE

This object show the license conrol status of a port. It is only applicable to a port which reuqires PORT license file to be adminstratively enabled (ifAdminStatus). 'locked' means the port requires PORT license file and PORT license file is absent 'unlocked' means the port requires PORT license file and PORT license file is present. 'notApplicable' means the port doesn't require PORT license file

OBJECT-TYPE

Used to enable/disable Tx flow control.

OBJECT-TYPE

Used to indicate the Tx flow control operational state.

OBJECT-TYPE

Port pcap Table

OBJECT-TYPE

Entry containing pcap info. for a particular port

OBJECT-TYPE

An index value that uniquely identifies a port. This value is similar to ifIndex in MIB2.

OBJECT-TYPE

To enable pcap for the port

OBJECT-TYPE

Mode in which pcap is enabled

OBJECT-TYPE

Used to indicate the number of filter list(s) that are assigned to this port.

OBJECT-TYPE

Used to indicate zero or more filter lists that are associated with this port for pcap. Each filter list identifier is stored as two bytes in this array starting from offset zero. Any unused bytes should be set to zero.

OBJECT-TYPE

Used to indicate the number of ACL filter(s) that are assigned to this port which has mirror set as global-action.

OBJECT-TYPE

Used to indicate zero or more ACL filter lists that are associated with this port for pcap (has mirror set as global-action). Each ACL filter list identifier is stored as two bytes in this array starting from offset zero. Any unused bytes should be set to zero.

OBJECT-TYPE

Port LACP table

OBJECT-TYPE

Entry containing info. for a particular port

OBJECT-TYPE

Administratively enable/disable LACP on a port

OBJECT-TYPE

Indicates if LACP is operationally enabled or disabled on a port

OBJECT-TYPE

The number of miliseconds between periodic transmissions using Short Timeouts.

OBJECT-TYPE

The number of miliseconds between periodic transmissions using LONG Timeouts.

OBJECT-TYPE

Scalar value used to calculate timeout time from periodic time. Timeout = PeriodicTime * TimeoutScale

OBJECT-TYPE

The number of mili seconds to delay aggregation to allow multiple links to aggregate simultaneously.

OBJECT-TYPE

The operating value of fast periodic timer on the port.

OBJECT-TYPE

The operating value of slow periodic timer on the port.

OBJECT-TYPE

The operating value of timeout scale on the port.

OBJECT-TYPE

The operating value of aggreagate wait time on port.

OBJECT-TYPE

Port Virtual LACP table

OBJECT-TYPE

Entry containing info. for a particular port

OBJECT-TYPE

Administratively enable/disable Virtual LACP on a port

OBJECT-TYPE

Indicates if Virtual LACP is operationally enabled or disabled on a port

OBJECT-TYPE

The number of miliseconds between periodic transmissions using Short Timeouts

OBJECT-TYPE

The number of miliseconds between periodic transmissions using LONG Timeouts.

OBJECT-TYPE

Timeout control value. Long or Short Timeout

OBJECT-TYPE

Scalar value used to calculate timeout time from periodic time. Timeout = PeriodicTime * TimeoutScale

OBJECT-TYPE

VLACP Protocol Identification. The id value is in Hex. Range in hex (0x600..0xffff)

OBJECT-TYPE

Multicast Mac Address exclusively used for VLACPDU's

OBJECT-TYPE

Display the Vlacp Port State.

OBJECT-TYPE

Port Remote Mirroring Table

OBJECT-TYPE

Entry containing remote mirroring info. for a particular port

OBJECT-TYPE

An index value that uniquely identifies a port. This value is similar to ifIndex in MIB2.

OBJECT-TYPE

To enable remote Mirroring for the port

OBJECT-TYPE

Mode in which remote mirroring is enabled

OBJECT-TYPE

Source Mac of the remote mirrored packet. Remote mirroring packet will be send with this source mac address

OBJECT-TYPE

Destination Mac of the remote mirrored packet. Packets will be bridged to this mac address. Remote mirroring packet will be send to this mac address

OBJECT-TYPE

Ethertype of the remote mirrored packet. Packets will be send with this ethertype

OBJECT-TYPE

Used to indicate the number of VLAN IDs that are assigned to this port.

OBJECT-TYPE

This field is used only if the port is assigned as remote mirroring termination port. Represents zero or more filter lists vlan in which the Destination Mac address resides. Each VLAN ID is stored as two bytes in this array starting from offset zero. Any unused bytes should be set to zero.

OBJECT-TYPE

RowStatus

OBJECT-TYPE

Port card mgmt port link table

OBJECT-TYPE

Entry containing info. for a particular mgmt port in I/O card

OBJECT-TYPE

IfIndex of the port.

OBJECT-TYPE

Port description

OBJECT-TYPE

admin status of the mgmt port

OBJECT-TYPE

Auto-negotiation status of the port

OBJECT-TYPE

duplex setting for the port

OBJECT-TYPE

speed setting for this port.

OBJECT-TYPE

Port Lossless Ethernet Table

OBJECT-TYPE

Entry containing lossless Ethernet information for a particular port.

OBJECT-TYPE

An index value that uniquely identifies a port. This value is similar to ifIndex in MIB2. Lossless Ethernet will be limited to 10Gig ports.

OBJECT-TYPE

To enable lossless mode for the port

OBJECT-TYPE

Pause frame type. fc - Pause, pfc - priority-based flow control.

OBJECT-TYPE

Guaranteed bandwidth in Gbps when rcPortLosslessEnetPauseType is set to pfc(2).

OBJECT-TYPE

Port table for all channelized capable ports.

OBJECT-TYPE

Entry containing info for a key port of channelized capable port.

OBJECT-TYPE

An index value that uniquely identifies a port which is channelized capable.

OBJECT-TYPE

port channelized type. Either 40G or 100G.

OBJECT-TYPE

Administratively enable/disable the port channelized mode.

OBJECT-TYPE

Port extend table.

OBJECT-TYPE

Entry containing info for a key port.

OBJECT-TYPE

The port format to display.

OBJECT-TYPE

A table that contains VLACP information about every port that is associated with this device. A row appears in this table for each physical port.

OBJECT-TYPE

A list of Virtual Link Aggregation Control Protocol statistics for each port on this device.

OBJECT-TYPE

The ifIndex of VLACP ports

OBJECT-TYPE

The number of valid VLACPDUs received on this Port. This value is read-only.

OBJECT-TYPE

The number of VLACPDUs transmitted on this Port. This value is read-only.

OBJECT-TYPE

The number of mismatched VLACPDUs in terms of seq-num RX'ed on this Port. This value is read-only.

OBJECT-IDENTITY

OBJECT-TYPE

Indicate whether the port lock feature is enabled.

OBJECT-TYPE

The set of ports that are administratively locked. Locked ports cannot be modified in anyway until the port is unlocked first.

OBJECT-TYPE

The ARU mode the chassis is operating in.

OBJECT-TYPE

The Quid mode the chassis is operating in.

OBJECT-TYPE

Used to specify the Enforce Operational Configuration Mode(EOC) of the system. When a device is configured with hardware of different revisions, the system will initialize in some deterministic manner (e.g., the lowest common denominator that makes sense based on the hardware configuration). This is the 'default(0)' mode. The user can override this behavior by manually specifying the EOC Mode they would like.

OBJECT-TYPE

Used to indicate the Enforce Operational Configuration Mode(EOC) of the system.

OBJECT-TYPE

Agents in a chassis table

OBJECT-TYPE

Entry containing info. for a particular agent

OBJECT-TYPE

entry id

OBJECT-TYPE

slot agent is in.

OBJECT-TYPE

agent's ip address.

OBJECT-TYPE

Used to indicate which ports in the system are configured as Brouter ports.

OBJECT-TYPE

Used to enable/disable global filters in the system. This variable is currently not supported.

OBJECT-TYPE

Used to enable/disable source MAC based VLANs in the system.

OBJECT-TYPE

Enhanced operational mode.

OBJECT-TYPE

This configuration is for enabling/disabling 128K mode. The change will take effect upon reboot.

OBJECT-TYPE

Used to indicate the Em-mode error status

OBJECT-TYPE

Enhanced Operational mode the switch currently has booted and will remain the same until the next reboot.

OBJECT-TYPE

EM mode the switch currently has booted and will remain the same until the next reboot.

OBJECT-TYPE

Used to enable/disable FTP daemon in 2nd cpu.

OBJECT-TYPE

Enable SMLT on single CP feature in the switch Not supported in VSP 3.3

OBJECT-TYPE

Vlan Optimization mode.

OBJECT-TYPE

Vlan Optimization mode the switch currently has booted and will remain the same until the next reboot.

OBJECT-IDENTITY

OBJECT-TYPE

Launch Pad in a chassis table

OBJECT-TYPE

Entry containing Launch pad card info

OBJECT-TYPE

Launch Pad card id

OBJECT-TYPE

Launch pad mini card id.

OBJECT-TYPE

Launch Pad application type.

OBJECT-TYPE

Launch Pad mini card's ip address.

OBJECT-TYPE

Enable/Disable naap Ip state.

OBJECT-TYPE

Launch Pad mini card's SW version.

OBJECT-TYPE

for identifying the ISD

OBJECT-TYPE

Launch Pad Cluster Table

OBJECT-TYPE

Entry containing Launch pad cluster info

OBJECT-TYPE

Launch pad cluster id.

OBJECT-TYPE

Launch Pad cluster type.

OBJECT-TYPE

Launch pad cluster size.

OBJECT-TYPE

Launch pad cluster members

OBJECT-TYPE

Launch pad cluster Row Status

OBJECT-TYPE

Launch pad cluster management vlan Id.

OBJECT-TYPE

Launch pad cluster cp sync vlan Id.

OBJECT-TYPE

Launch pad cluster TPS size.

OBJECT-TYPE

Launch pad cluster TPS members

OBJECT-TYPE

IS cluster user port list that needs to be monitored

OBJECT-TYPE

To enable/disbale to napp feature.

OBJECT-TYPE

Global Filter ordering in the system.

OBJECT-TYPE

This configuration is for enabling/disabling global filter ordering. The change will take effect upon reboot.

OBJECT-TYPE

This configuration is for enabling/disabling 256K mode. The change will take effect upon reboot.

OBJECT-TYPE

R-mode the switch currently has booted and will remain the same until the next reboot.

OBJECT-TYPE

Used to indicate the r-mode error status

OBJECT-TYPE

Used to enable/disable Multicast check packet in the system. This change will take effect upon reboot.

OBJECT-TYPE

Enable/Disable System monitoring in the switch

OBJECT-TYPE

Dyanamically Enable/Disable SystemMonitor monitoring engine in the switch

OBJECT-TYPE

System Monitor Detection time in seconds

OBJECT-TYPE

Used to reserve MGIDs for IP Multicast. The change will take effect upon reboot.

OBJECT-TYPE

MGIDs the switch currently has reserved for IP Multicast; will remain the same until the next reboot.

OBJECT-TYPE

A mode where all MGIDs are reserved for VLAN use only; no IPMC. The change will take effect upon reboot.

OBJECT-TYPE

Tells if all MGIDs are reserved for VLAN use. Will remain the same until the next reboot.

OBJECT-TYPE

Number of MGIDs currently used for VLAN, including SMLT

OBJECT-TYPE

Number of MGIDs remaining allocated for VLAN

OBJECT-TYPE

Number of MGIDs currently used for IPMC

OBJECT-TYPE

Number of MGIDs remaining allocated for IPMC

OBJECT-TYPE

Used to enable/disable flag which is used to set the CLIP-ip as topology ip

OBJECT-TYPE

The Clip-Id set by the user to be used as Topology-ip. 0' means no circuitless IP id while '1..256' is valid circuitless Id

OBJECT-TYPE

On or off value of Chassis Power Management which the switch has currently booted. It will remain the same until the next reboot.

OBJECT-TYPE

Turn on or off the Fan Check functionility of Chassis Power Management. The value takes effect only on reboot.

OBJECT-TYPE

The on or off value of fan check which the switch has booted with. The value does not take effect till the next reboot.

OBJECT-TYPE

Used to default the system

OBJECT-TYPE

Used to enable/disable flag which is used for Security Console.When it is enabled, the console connection works only with the null modem cable

OBJECT-IDENTITY

OBJECT-TYPE

This table contains information about LEDs of the chassis

OBJECT-TYPE

Contains information regarding a LED Unit

OBJECT-TYPE

The chassis LED Id.

OBJECT-TYPE

The LED's label name.

OBJECT-TYPE

Type of the Led: - unknown(1) - type can not be determined. - greenSteady(2), - greenBlinking(3), - amberSteady(4), - amberBlinking(5), - off(6), - redSteady(7), - redBlinking(8) For different LED, the meaning of each status is different.

OBJECT-TYPE

Device part number or PEC code

OBJECT-TYPE

Chassis model name. For APLS platform, it is model name which is in teh seeprom

OBJECT-TYPE

Chassis brand name. For APLS platform, it is programmed in the seeprom

OBJECT-IDENTITY

OBJECT-TYPE

Control whether Mirror configuration information should be saved to NVRAM so mirror settings can be automatically reinstalled after a system reboot. Setting rcMirrorSaveConfig to true does not immediately save the configuration information. The save happens when the rcSysAction variable is set to 'saveToNVRAM(4)'.

OBJECT-IDENTITY

OBJECT-TYPE

Used to indicate whether the mirror by port feature is active. The system can only support mirroring on two ports. When this feature is active, all packets received on the port(s) specified by rcMirrorSrcPortOne and/or rcMirrorSrcPortTwo are copied to rcMirrorDstPort. The mirroring operation is non-intrusive.

OBJECT-TYPE

The ifIndex of the port to forward mirrored frames to.

OBJECT-TYPE

Used to indicate whether the port specified in rcMirrorByPortMirroredPortOne should be mirrored.

OBJECT-TYPE

The ifIndex of the port to be mirrored. That is, traffic received on this port will be sent to the mirror port.

OBJECT-TYPE

Used to indicate whether the port specified in rcMirrorByPortMirroredPortTwo should be mirrored.

OBJECT-TYPE

The ifIndex of the port to be mirrored. That is, traffic received on this port will be sent to the mirror port.

OBJECT-IDENTITY

OBJECT-TYPE

Used to indicate whether ports that are unconfigured should be assigned to the 'isolated' VLAN. Ports assigned to the 'isolated' VLAN can only communicate with the CP port. If this option is not specified, unconfigured ports will be assigned to the 'default' VLAN

OBJECT-TYPE

Used to indicate whether the system should ignore the configuration information stored in NVRAM when the system is booted.

OBJECT-TYPE

Used to indicate whether the system is configured to operate in a high priority mode. The switch can operate in either a 'best effort' or 'high priority' mode. In the 'best effort' setting, the maximum queue thresholds for the QUIDs are set to 768/768 buffers. In the 'high priority' mode the setting is 512/768. This means that in 'high priority' mode the normal priority queue can't have more than 512 buffers, while the high priority queue can have up to 768.

OBJECT-IDENTITY

OBJECT-TYPE

Used to indicate the current size of the RMON Statistic table.

OBJECT-TYPE

Used to indicate the current size of the RMON History Control table.

OBJECT-TYPE

Used to indicate the current size of the RMON History Ethernet table.

OBJECT-TYPE

Used to indicate the current size of the RMON Alarm table.

OBJECT-TYPE

Used to indicate the current size of the RMON Event table.

OBJECT-TYPE

Used to indicate the current size of the RMON Log table.

OBJECT-TYPE

Used to indicate the size of the Address Translation (AR) table.

OBJECT-TYPE

Used to indicate the number of free entries that are available in the Address Translation (AR) table.

OBJECT-TYPE

Used to indicate the number of entries that could not be added to the Address Translation (AR) table due to lack of space.

OBJECT-TYPE

Used to indicate the number of entries added to the Address Translation (AR) table.

OBJECT-TYPE

Used to indicate the number of entries deleted to the Address Translation (AR) table.

OBJECT-TYPE

Used to indicate the number of MAC entries added to the Address Translation (AR) table.

OBJECT-TYPE

Used to indicate the number of MAC entries deleted to the Address Translation (AR) table.

OBJECT-TYPE

Used to indicate the number of MAC entries moved in the Address Translation (AR) table.

OBJECT-TYPE

Used to indicate the number of IP entries added to the Address Translation (AR) table.

OBJECT-TYPE

Used to indicate the number of IP entries deleted to the Address Translation (AR) table.

OBJECT-TYPE

Used to indicate the size of the Multicast Address Translation (AR) table.

OBJECT-TYPE

Used to indicate the number of free multicast groups availabe in the Address Translation (AR) table.

OBJECT-TYPE

Used to indicate the number of Ip multicast entries that are added to the Address Translation (AR) table.

OBJECT-TYPE

Used to indicate the number of Ip multicast entries that are deleted from the Address Translation (AR) table.

OBJECT-TYPE

Used to indicate the number of VLAN by port entries that are added to the Address Translation (AR) table.

OBJECT-TYPE

Used to indicate the number of VLAN by port entries that are deleted from the Address Translation (AR) table.

OBJECT-TYPE

Used to indicate the number of Vlans by Protocol Type entries that are added to the Address Translation (AR) table.

OBJECT-TYPE

Used to indicate the number of Vlans by Protocol Type entries that are deleted from the Address Translation (AR) table.

OBJECT-TYPE

Used to indicate the number of VLAN by Ip entries that are added to the Address Translation (AR) table.

OBJECT-TYPE

Used to indicate the number of VLAN by Ip entries that are deleted from the Address Translation (AR) table.

OBJECT-TYPE

Used to indicate the number of Ip subnet entries that are added to the Address Translation (AR) table.

OBJECT-TYPE

Used to indicate the number of Ip subnet entries that are deleted from the Address Translation (AR) table.

OBJECT-TYPE

Used to indicate the number of RSVP entries that are added to the Address Translation (AR) table.

OBJECT-TYPE

Used to indicate the number of RSVP entries that are deleted from the Address Translation (AR) table.

OBJECT-TYPE

Used to indicate the number of entries in the dot1d forwarding database table.

OBJECT-TYPE

Used to indicate the number of entries in the dot1d Static Address Filtering table.

OBJECT-TYPE

Used to indicate the number of entries in the IP Address table.

OBJECT-TYPE

Used to indicate the number of entries in the IP Forwarding/Best Route table.

OBJECT-TYPE

Used to indicate the number of entries in the IP Net-to-media table.

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

A table used to maintain IP routing information for a particular interface.

OBJECT-TYPE

Entry containing IP routing information. An entry is automatically created in this table when routing is enabled for an interface -or- when an ip address is configured on an interface.

OBJECT-TYPE

An unique value to identify a physical interface or a logical interface (VLAN).

OBJECT-TYPE

Used to indicate whether this interface should advertize a RIP default route.

OBJECT-TYPE

Used to indicate whether this interface should accept a RIP default route.

OBJECT-TYPE

Row status for this entry.

OBJECT-TYPE

Enable or disable RIP routing on the specified interface.

OBJECT-TYPE

Enable or disable OSPF routing on the specified interface.

OBJECT-TYPE

Enable or disable IGMP on the specified interface.

OBJECT-TYPE

Indicate whether IpAddress has been assigned for this interface.

OBJECT-TYPE

Enable or disable DHCP on the specified interface.

OBJECT-TYPE

Used to indicate whether the RIP triggered update feature should be enabled on this interface.

OBJECT-TYPE

Used to indicate whether the auto aggregation feature should be enabled on this interface.

OBJECT-TYPE

Used to indicate whether to generate a default RIP route on this interface.

OBJECT-TYPE

The value is used indicated whether vlan state change should be notified to layer 3 or not, provided the vlan is configured as routable interface. Also used for single routable ports, in that case the criteria for state is PortOperStatus. Vlan is considered as UP if atleast one member of the port based vlan has link up, or atleast one port member of the policy based has an entry in the MGID or atleast one static member of the policy based vlan has link up. Otherwise, vlan is considered as DOWN. If the value is 'true' then the interface state change will not be notified to layer 3. (i.e., it always stays up). If the value is 'false' then the vlan state change will be notified to layer 3 so that IP related status reflects routable interface state.

OBJECT-TYPE

Used to indicate whether this interface should forward direct broadcast traffic

OBJECT-TYPE

Used to indicate whether this interface should advertize a RIP default route.

OBJECT-TYPE

Used to indicate whether this interface should accept a RIP default route.

OBJECT-TYPE

OSPF Interface Type.

OBJECT-TYPE

Used to indicate the rip cost for this interface.

OBJECT-TYPE

Used to indicate the rip holddown timer for this interface

OBJECT-TYPE

Used to indicate the rip timeout interval for this interface

OBJECT-TYPE

Used to enable Route Smlt feature.

OBJECT-TYPE

Used to indicate whether this interface should perform Reverse Path Check

OBJECT-TYPE

Reverse Path Checking mode.

OBJECT-TYPE

Enable or disable ipvpn-lite capability on the specified circuitless ip interface.

OBJECT-TYPE

Enable or disable spb-multicast on this port

OBJECT-TYPE

Set the VRRP version for IPv4 on the specified interface. It does not impact the use of IPv6 VRRPv3

OBJECT-TYPE

Enable or disable PIM Gateway on this port

OBJECT-TYPE

Set the IPv4 VRRPv3 checksum computation method on the specified interface.

OBJECT-TYPE

Used to enable ipsec feature.

OBJECT-TYPE

A table used to maintain OSPF information for a particular interface.

OBJECT-TYPE

Entry containing OSPF information. An entry is automatically created in this table when routing is enabled for an interface -or- when an ip address is configured on an interface.

OBJECT-TYPE

An unique value to identify a physical interface or a logical interface (VLAN).

OBJECT-TYPE

The priority of this interface. Used in multi- access networks, this field is used in the designated router election algorithm. The value 0 signifies that the router is not eligible to become the designated router on this particular network. In the event of a tie in this value, routers will use their router id as a tie breaker.

OBJECT-TYPE

The metric for this type of service (TOS) on this interface. The default value of the TOS 0 Metric is (10^9 / ifSpeed). The value FFFF means 'no route via this TOS'. A value of 0 means the interface speed (rcIpConfOspfDefaultMetric) will be used as metric value, when the state of the interface is up.

OBJECT-TYPE

The Authentication Key. If the Area's Authorization Type is simplePassword, and the key length is shorter than 8 octets, the agent will left adjust and zero fill to 8 octets. Note that unauthenticated interfaces need no authentication key, and simple password authen- tication cannot use a key of more than 8 oc- tets. Larger keys are useful only with authen- tication mechanisms not specified in this docu- ment. When read, ospfIfAuthKey always returns an Octet String of length zero.

OBJECT-TYPE

Row status for this entry.

OBJECT-TYPE

The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for all routers attached to a common network.

OBJECT-TYPE

The number of seconds that a router's Hello packets have not been seen before it's neighbors declare the router down. This should be some multiple of the Hello interval. This value must be the same for all routers attached to a common network.

OBJECT-TYPE

A 32-bit integer uniquely identifying the area to which the interface connects. Area ID 0.0.0.0 is used for the OSPF backbone.

OBJECT-TYPE

The authentication type specified for an interface. Additional authentication types may be assigned locally.

OBJECT-TYPE

OSPF NBMA Interface Poll Interval.

OBJECT-TYPE

Mtu-ignore flag is for ignoring the mtu checking in ospf bdb

OBJECT-IDENTITY

OBJECT-TYPE

Used to indicate the cost associated with 10Meg Interface(Port).

OBJECT-TYPE

Used to indicate the cost associated with 100Meg Interface(Port).

OBJECT-TYPE

Used to indicate the cost associated with 1000Meg Interface(Port).

OBJECT-TYPE

Used to indicate the cost associated with 10000Meg Interface(Port).

OBJECT-TYPE

Used to indicate the cost associated with 40000Meg Interface(Port).

OBJECT-TYPE

Used to indicate the cost associated with Vlan Interface

OBJECT-TYPE

Used to indicate the cost associated with 100000Meg Interface(Port).

OBJECT-TYPE

Used to indicate the cost associated with 25000Meg Interface(Port).

OBJECT-IDENTITY

OBJECT-TYPE

Used to indicate whether Ospf Traps should be sent.

OBJECT-TYPE

Used to indicate whether auto virtual link creation is enabled or not. If set to true OSPF will create virtual links between ABRs whether it is needed or not, but adjacency will established only when one of the ABR losses connection to backbone area. If set to false then it is user resposibity to create virtual link whenever needed.

OBJECT-TYPE

The SPF Hold Down Timer value. The SPF will run at most once per hold down timer value.

OBJECT-TYPE

OBJECT-TYPE

Controls the preference rules used when choosing among multiple AS-External-LSAs advertising the same destination. When this is enabled, the preference rule will be same as specified by RFC1583. When disabled, the new preference rule as described in RFC2328 will be applicable, which potentially prevents the routing loops when AS-External-LSAs for the same destination have been originated from different areas.

OBJECT-TYPE

Disables Graceful Restart Helper Mode feature. The feature is enabled by default (so this flag is disabled by default).

OBJECT-IDENTITY

OBJECT-TYPE

Used to set the system-wide RIP hold down time in seconds.

OBJECT-TYPE

Used to set the icmp net unreach feature enable/disable.

OBJECT-TYPE

Used to set the ecmp enable/disable.

OBJECT-TYPE

Used to globally configure maximum ECMP paths number.

OBJECT-TYPE

Used to globally configure alternative enable.

OBJECT-TYPE

Enable/disable ICMP Route Discovery feature

OBJECT-TYPE

Rip TimeOut Interval in seconds

OBJECT-TYPE

Rip def import metric

OBJECT-TYPE

Routes to networks specified in this prefix-list can have upto 1 ECMP path, irrespective of ecmp-max-path configuration

OBJECT-TYPE

Routes to networks specified in this prefix-list can have upto 2 ECMP path, irrespective of ecmp-max-path configuration.

OBJECT-TYPE

Routes to networks specified in this prefix-list can have upto 3 ECMP path, irrespective of ecmp-max-path configuration.

OBJECT-TYPE

Routes to networks specified in this prefix-list can have upto 4 ECMP path, irrespective of ecmp-max-path configuration.

OBJECT-TYPE

This is to apply any changes in ECMP path list configuration or in the prefix-lists configured to be used as path list

OBJECT-TYPE

OBJECT-TYPE

Defines the maximum number of outstanding arp request a switch can generate.

OBJECT-TYPE

Used to determine whether more specific non local routes will go into the routing table.

OBJECT-TYPE

Enable/disable UDP checksum calculation

OBJECT-TYPE

Used to globally enable Supernetting/ CIDR routing for IP

OBJECT-TYPE

Routes to networks specified in this prefix-list can have upto 5 ECMP path, irrespective of ecmp-max-path configuration.

OBJECT-TYPE

Routes to networks specified in this prefix-list can have upto 6 ECMP path, irrespective of ecmp-max-path configuration.

OBJECT-TYPE

Routes to networks specified in this prefix-list can have upto 7 ECMP path, irrespective of ecmp-max-path configuration.

OBJECT-TYPE

Routes to networks specified in this prefix-list can have upto 8 ECMP path, irrespective of ecmp-max-path configuration.

OBJECT-TYPE

Used to set the gratuitous-arp enable/disable.

OBJECT-TYPE

Enable/disable Ip Arp Multicast Mac Flooding feature.

OBJECT-TYPE

Used to globally enable/disable ip source routing feature.

OBJECT-TYPE

Used to globally enable/disable ip icmp echo broadcast request feature.

OBJECT-TYPE

A table used to maintain OSPF information for a particular Area.

OBJECT-TYPE

Entry containing OSPF Area configuration information. An entry is automatically created in this table when an area is configured through ospfAreaTable in (rfc1253rcc.mib).

OBJECT-TYPE

An unique value to identify an area. Area ID 0.0.0.0 is used for the OSPF backbone.

OBJECT-TYPE

The area's support for importing Summary advertisements into a stub area. This field should be used only if ospfImportASExtern is set to FALSE

OBJECT-TYPE

This variable displays the number of active interfaces configured in this area. An area cannot be deleted if this value is > 0.

OBJECT-TYPE

A table used to maintain IP routing information for a particular interface.

OBJECT-TYPE

Entry containing IP routing information. An entry is automatically created in this table when routing is enabled for an interface -or- when an ip address is configured on an interface.

OBJECT-TYPE

An unique value to identify a physical interface or a logical interface (VLAN).

OBJECT-TYPE

Ip interface address.

OBJECT-TYPE

Row status for this entry.

OBJECT-TYPE

Used to indicate whether this interface should advertize a RIP default route.

OBJECT-TYPE

Used to indicate whether this interface should accept a RIP default route.

OBJECT-TYPE

Enable or disable RIP routing on the specified interface.

OBJECT-TYPE

Enable or disable OSPF routing on the specified interface.

OBJECT-TYPE

Enable or disable IGMP on the specified interface.

OBJECT-TYPE

Indicate whether IpAddress has been assigned for this interface.

OBJECT-TYPE

Used to indicate whether the RIP triggered update feature should be enabled on this interface.

OBJECT-TYPE

Used to indicate whether the auto aggregation feature should be enabled on this interface.

OBJECT-TYPE

Used to indicate whether to generate a default RIP route on this interface.

OBJECT-TYPE

The value is used indicated whether vlan state change should be notified to layer 3 or not, provided the vlan is configured as routable interface. Also used for single routable ports, in that case the criteria for state is PortOperStatus. Vlan is considered as UP if atleast one member of the port based vlan has link up, or atleast one port member of the policy based has an entry in the MGID or atleast one static member of the policy based vlan has link up. Otherwise, vlan is considered as DOWN. If the value is 'true' then the interface state change will not be notified to layer 3. (i.e., it always stays up). If the value is 'false' then the vlan state change will be notified to layer 3 so that IP related status reflects routable interface state.

OBJECT-TYPE

A table used to maintain OSPF information for a particular interface.

OBJECT-TYPE

Entry containing OSPF information. An entry is automatically created in this table when routing is enabled for an interface -or- when an ip address is configured on an interface.

OBJECT-TYPE

An unique value to identify a physical interface or a logical interface (VLAN).

OBJECT-TYPE

IpAddress of the IP interface.

OBJECT-TYPE

The priority of this interface. Used in multi- access networks, this field is used in the designated router election algorithm. The value 0 signifies that the router is not eligible to become the designated router on this particular network. In the event of a tie in this value, routers will use their router id as a tie breaker.

OBJECT-TYPE

The metric for this type of service (TOS) on this interface. The default value of the TOS 0 Metric is (10^9 / ifSpeed). The value FFFF means 'no route via this TOS'. A value of 0 means the interface speed (rcIpConfOspfV2DefaultMetric) will be used as metric value, when the state of the interface is up.

OBJECT-TYPE

The Authentication Key. If the Area's Authorization Type is simplePassword, and the key length is shorter than 8 octets, the agent will left adjust and zero fill to 8 octets. When read, ospfIfAuthKey always returns an Octet String of length zero.

OBJECT-TYPE

Row status for this entry.

OBJECT-TYPE

The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for all routers attached to a common network.

OBJECT-TYPE

The number of seconds that a router's Hello packets have not been seen before it's neighbors declare the router down. This should be some multiple of the Hello interval. This value must be the same for all routers attached to a common network.

OBJECT-TYPE

A 32-bit integer uniquely identifying the area to which the interface connects. Area ID 0.0.0.0 is used for the OSPF backbone.

OBJECT-TYPE

The authentication type specified for an interface. Additional authentication types may be assigned locally.

OBJECT-TYPE

A table used to maintain OSPF summary route metric parameter for a particular Area range.

OBJECT-TYPE

Entry containing OSPF summary route metric parameter for a particular Area range. An entry is automatically created in this table when an area range is configured through ospfAreaAggregateTable in rfc1850rcc.mib

OBJECT-TYPE

The Area the Address Aggregate is to be found within.

OBJECT-TYPE

The type of the Address Aggregate. This field specifies the Lsdb type that this Address Ag- gregate applies to.

OBJECT-TYPE

The IP Address of the Net or Subnet indicated by the range.

OBJECT-TYPE

The Subnet Mask that pertains to the Net or Subnet.

OBJECT-TYPE

Used to specify a metric for a Summary LSA (type 3) generated by OSPF through an area range. If this metric is set to 0, OSPF uses the cost to the farthest point in the networks being summarized as the metric.

OBJECT-TYPE

Subnets subsumed by ranges either trigger the advertisement of the indicated aggregate (ad- vertiseMatching), or result in the subnet's not being advertised at all outside the area.

OBJECT-TYPE

A table used to maintain OSPF summary route metric parameter for a particular Area range.

OBJECT-TYPE

Entry containing OSPF summary route metric parameter for a particular Area range. An entry is automatically created in this table when an area range is configured through ospfAreaAggregateTable in rfc1850rcc.mib

OBJECT-TYPE

Interface Index, this is an index of the table.

OBJECT-TYPE

Timer value, the range of value is from 0 to 3600.

OBJECT-TYPE

The range of value 0 to 3600 or 9999. 9999 means infinity.

OBJECT-TYPE

Row Status.

OBJECT-TYPE

The table of addressing information relevant to this entity's IP addresses. This table is identical to the ipAddrTable in MIB2 except the columns rcIpAdEntIfIndex and rcIpAdEntAddr are reversed. Also, the table is indexed by both these variables.

OBJECT-TYPE

The addressing information for one of this entity's IP addresses.

OBJECT-TYPE

The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.

OBJECT-TYPE

The IP address to which this entry's addressing information pertains.

OBJECT-TYPE

The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0.

OBJECT-TYPE

The IP broadcast address format used on this interface.

OBJECT-TYPE

The size of the largest IP datagram which this entity can re-assemble from incoming IP fragmented datagrams received on this interface.

OBJECT-TYPE

Used to create/delete entries

OBJECT-TYPE

A value that uniquely identifies the Virtual LAN associated with this entry. This value corresponds to the lower 12 bits in the IEEE 802.1Q VLAN Tag.

OBJECT-TYPE

Used to indicate whether this entry correponds to a brouter port (as oppose to a routable VLAN). This value cannot be changed after the row is created.

OBJECT-TYPE

Used to translate the ip address into mac address. The system has 512 mac addresses of which 0-507 are reserved for Boardwalk box. 508-511 is reserved for MG. One can either mention a mac offset while configuring an ip on the vlan or it can be alloted by the system within the above range.

OBJECT-TYPE

The address entry IfType indicates the type of the interface. In the case of circuit-less-IP there is no association with any ports. In other words, it can be thought of as a virtual interface. The value 'brouter port' indicates this interface is associated with a specific physical port. The value 'vlan' indicates a logical port that contains one or physical ports/MLT ports.

OBJECT-TYPE

The VrfId used in this table is to associate VLANs or Brouter ports to a VRF after the creation of VLANs or Brouter ports. VRFID 0 is reserved for the Administrative VRF.

OBJECT-TYPE

IpFlow Table. This table contain entries that correspond to RSVP records in the switching fabric Address Resolution table. A connection that has a matching entry in this table will be processed with a higher priority than connections that do not have an entry.

OBJECT-TYPE

Proprietary flow control variables.

OBJECT-TYPE

The source IP address of an IP packet.

OBJECT-TYPE

The source port of an IP packet. A zero value in this field is used as a wildcard value.

OBJECT-TYPE

The destination IP address of an IP packet.

OBJECT-TYPE

The destination port of an IP packet. A zero value in this field is used as a wildcard value.

OBJECT-TYPE

The protocol type of an IP packet. A zero value in this field is used as a wildcard value.

OBJECT-TYPE

Status of entry.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

Used to indicate whether or not to Redistribute RIP routes to OSPF.

OBJECT-TYPE

Value of metric that is used to translate the RIP route to OSPF.

OBJECT-TYPE

Used to indicate whether or not to use the user specified default metric for redistributing RIP routes to OSPF.

OBJECT-TYPE

Used to configure the metric type of the distributed routes to OSPF domain. type1 means the metric is comparable directly to the link state metric (cost = internal cost + external cost). type2 means the metric is considered larger than any link state metric (cost = external cost).

OBJECT-IDENTITY

OBJECT-TYPE

Used to indicate whether or not to redistribute OSPF routes to RIP.

OBJECT-TYPE

Value of metric that is used to translate the OSPF route to RIP.

OBJECT-TYPE

Used to indicate whether or not to use the user specified default metric for redistributing OSPF routes to RIP.

OBJECT-IDENTITY

OBJECT-TYPE

Used to indicate whether directly connected networks through non-ospf interfaces are distributed to OSPF database or not. If set to true all the static routes will be added as external routes to OSPF routing domain, provided the router is configured as AS Border router. Also originates asExtern link LSA.

OBJECT-TYPE

Used to indicate whether or not to use the user specified default metric for redistributing direct routes to OSPF.

OBJECT-TYPE

Value of metric that is used to translate the routes to directly connected networks to OSPF.

OBJECT-TYPE

Used to configure the metric type of the distributed routes to OSPF domain. type1 means the metric is comparable directly to the link state metric (cost = internal cost + external cost). type2 means the metric is considered larger than any link state metric (cost = external cost).

OBJECT-IDENTITY

OBJECT-TYPE

Used to indicate whether static routes (that are configured locally through management protocol) are distributed to OSPF database or not. If set to true all the static routes will be added as external routes to OSPF routing domain, provided the router is configured as AS Border router. Also originates asExtern link LSA.

OBJECT-TYPE

Value of metric that is used to translate the static routes to OSPF.

OBJECT-TYPE

Used to indicate whether or not to use the user specified default metric for redistributing static routes to OSPF.

OBJECT-TYPE

Used to configure the metric type of the distributed routes to OSPF domain. type1 means the metric is comparable directly to the link state metric (cost = internal cost + external cost). type2 means the metric is considered larger than any link state metric (cost = external cost).

OBJECT-TYPE

Used to indicate whether default route (that are configured locally through management protocol) should be distributed to OSPF database or not. If set to true then the default route will be added as external route to OSPF routing domain, provided the router is configured as AS Border router. Also originates asExtern link LSA.

OBJECT-IDENTITY

OBJECT-TYPE

Used to indicate whether directly connected networks through non-rip interfaces are distributed to RIP or not.

OBJECT-IDENTITY

OBJECT-TYPE

Used to indicate whether static routes (that are configured locally through management protocol) are distributed to RIP database or not. If set to true all the static routes will be added as external routes to RIP routing domain.

OBJECT-TYPE

A table used to maintain IGMP information for a particular interface.

OBJECT-TYPE

Entry containing IGMP information. An entry is automatically created in this table when routing is enabled for an interface -or- when an ip address is configured on an interface.

OBJECT-TYPE

An unique value to identify a physical interface or a logical interface (VLAN).

OBJECT-TYPE

The frequency at which IGMP Host-Query packets are transmitted on this interface.

OBJECT-TYPE

The version of IGMP which is running on this interface. This object can be used to configure a router capable of running either value. For IGMP to function correctly, all routers on a LAN must be configured to run the same version of IGMP on that LAN.

OBJECT-TYPE

The maximum query response time advertised in IGMPv2 queries on this interface. Smaller values allow a router to prune groups faster.

OBJECT-TYPE

A timeout interval. If no IGMPv2 queries are heard on this interface within this timeout interval, the local router will take over the Querier on the IP subnet to which this interface is attached.

OBJECT-TYPE

An indication of whether the processing of IGMPv2 Leave messages is enabled on this interface.

OBJECT-TYPE

Status of entry.

OBJECT-TYPE

lossiness of network.

OBJECT-TYPE

max response in GrpSpec Query.

OBJECT-TYPE

Enable snoop.

OBJECT-TYPE

Enable proxy snoop.

OBJECT-TYPE

The (conceptual) table listing the multicast groups configured in the device.

OBJECT-TYPE

An entry (conceptual row) representing an Igmp group.

OBJECT-TYPE

Multicast group Address (Class D) that others want to join. A group address can be the same for many incoming ports.

OBJECT-TYPE

IP Address of a source that has sent group report wishing to join this group.

OBJECT-TYPE

An unique value to identify a physical interface or a logical interface (VLAN), which has received Group reports from various sources.

OBJECT-TYPE

Time left before the group report expired on this port. Only one of this variable port. This variable is updated upon receiving a group report.

OBJECT-TYPE

An unique value to identify a physical interface or a logical interface (VLAN), which has received Group reports from various sources.

OBJECT-TYPE

User-id sending this group

OBJECT-TYPE

Used for IGAP, to indicated member state.

OBJECT-TYPE

Used for IGAP, to indicated the session time in seconds for the member. Session time is started after traffic is available to member. It can be also called AccountingTime since its values correspondes to the accounting duration of IGAP user session.

OBJECT-TYPE

This entity's IP Routing table.

OBJECT-TYPE

A route to a particular destination.

OBJECT-TYPE

The destination IP address of this route. An entry with a value of 0.0.0.0 is considered a default route. Multiple routes to a single destination can appear in the table, but access to such multiple entries is dependent on the table- access mechanisms defined by the network management protocol in use.

OBJECT-TYPE

Indicate the mask to be logical-ANDed with the destination address before being compared to the value in the rcIpRouteDest field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the rcIpRouteMask by determining whether the value of the correspondent rcIpRouteDest field belong to a class-A, B, or C network, and then using one of: mask network 255.0.0.0 class-A 255.255.0.0 class-B 255.255.255.0 class-C If the value of the rcIpRouteDest is 0.0.0.0 (a default route), then the mask value is also 0.0.0.0. It should be noted that all IP routing subsystems implicitly use this mechanism.

OBJECT-TYPE

The IP address of the next hop of this route. (In the case of a route bound to an interface which is realized via a broadcast media, the value of this field is the agent's IP address on that interface).

OBJECT-TYPE

The primary routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's rcIpRouteProto value. If this metric is not used, its value should be set to -1.

OBJECT-TYPE

The index value which uniquely identifies the local interface through which the next hop of this route should be reached. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.

OBJECT-TYPE

The type of route.

OBJECT-TYPE

The routing mechanism via which this route was learned. Inclusion of values for gateway routing protocols is not intended to imply that hosts should support those protocols.

OBJECT-TYPE

The number of seconds since this route was last updated or otherwise determined to be correct. Note that no semantics of `too old' can be implied except through knowledge of the routing protocol by which the route was learned.

OBJECT-TYPE

Used to create/delete entries

OBJECT-TYPE

OBJECT-TYPE

Alternative Route Sequence. 0 denotes Best Route.

OBJECT-TYPE

The type of route. It is a combination of direct, indirect, best, alternative and ECMP path.

OBJECT-TYPE

srcVrfId of the next-hop address

OBJECT-TYPE

Identifier of the next-hop, hostname or mac adress.

OBJECT-TYPE

Identifies type for value specified in the rcIpRouteLayer3VirtualInterface field.

OBJECT-TYPE

Identifier of the Layer3 Virtual Interface. When the value is an SPB I-SID, 0 denotes GlobalRouter and -1 denotes not applicable to route.

OBJECT-TYPE

DHCP configuration table

OBJECT-TYPE

Used to configure DHCP on a particular port. An entry is created automatically when the variable rcIpConfDhcpEnable is set to TRUE. Once created this entry will only be deleted if the rcIpConfDhcpRowStatus is set to 'destroy(6)'. In which case, the rcIpConfDhcpEnable is automatically reset to the FALSE setting.

OBJECT-TYPE

Interface number. The number can represent either a physical or logical(VLAN) interface.

OBJECT-TYPE

Used to indicate the maximum number of hops a DHCP packet can take from the source device to the destination device (i.e., DHCP client to DHCP server).

OBJECT-TYPE

Used to indicate the minimum number of seconds to wait between receiving a DHCP packet and actually forwarding the DHCP packet to the destination device. A value of zero(0) indicates forwarding should be done immediately without any delay.

OBJECT-TYPE

Used to indicate what type of DHCP packets this interface should support. A value of none(1) will result in all incoming DHCP and BOOTP packets to be dropped.

OBJECT-TYPE

An entry is created automatically when the variable rcIpConfDhcpEnable is set to TRUE. Once created this entry will only be deleted if the rcIpConfDhcpRowStatus is set to 'destroy(6)'. In which case, the rcIpConfDhcpEnable is automatically reset to the FALSE setting.

OBJECT-TYPE

The total number of DHCP requests seen on this interface.

OBJECT-TYPE

The total number of DHCP replies seen on this interface.

OBJECT-TYPE

Used to indicate if DHCP Reply packets should be broadcast to the DHCP client on this interface.

OBJECT-TYPE

This object is used to clear the DHCP counters in an entry. When set to clear(1), the values of the counter objects in the entry will be reset to 0. When read, the value of this object is always dummy(2).

OBJECT-TYPE

Used to indicate if DHCP packets should have option82 circuitId info inserted before sent to servers, for this interface.

OBJECT-TYPE

Used to indicate if DHCP packets should have option82 remoteId info inserted before sent to servers, for this interface.

OBJECT-TYPE

Used to indicate if DHCP packets come through a trusted dhcp circuit. This means that packets with giaddr set to 0 having option82 in it, will be forwarded if the circuit is trusted.

OBJECT-TYPE

The IP address configured as relay on this interface; it is either the IP of the physical interface or the IP of the VRRP address

OBJECT-TYPE

DHCP forwarding table.

OBJECT-TYPE

An entry used represents a DHCP forwarding directive.

OBJECT-TYPE

The IP address configured on an interface (i.e., a locally configured IP address).

OBJECT-TYPE

The IP address of the DHCP server. If this IP address corresponds to a locally configured IP network, the DHCP packet is broadcasted out the interface the IP address is assigned to. This behavior is known as 'relay agent' mode. If this IP address is a remote address, the DHCP packet is sent via unicast to the remote device. This behavior is known as 'preferred server' mode.

OBJECT-TYPE

Used to indicate whether this entry should be used.

OBJECT-TYPE

Used to indicate whether this entry pertains to BOOTP packets, DHCP packets, or both.

OBJECT-TYPE

Row status of this entry.

OBJECT-IDENTITY

OBJECT-TYPE

Used to indicate the number of entries in the rcIpFilterTable.

OBJECT-TYPE

Used to indicate the number of entries in the rcIpFilterGlobalListTable.

OBJECT-TYPE

Used to indicate the number of entries in the rcIpFilterBaseListTable.

OBJECT-TYPE

Used to indicate the number of entries in the rcIpFilterPortTable.

OBJECT-TYPE

next available filter-id in the rcIpFilterPortTable.

OBJECT-TYPE

A table containing IP filters.

OBJECT-TYPE

IP filter attributes. The system supports a vast array of filter options. Each of these options are supported in this entry. If a particular option is not used, the column should be set to zero.

OBJECT-TYPE

Used to indicate a particular type of filter. A 'global' filter is a filter that is applied to all packets irregardless of the packet's source or destination IP address. A 'destination' filter is used to match the destination IP address field of incoming packets. When a match is found, this filter is applied to the packet. A 'source' filter is used to match the source IP address field of incoming packets. When a match is found, this filter is applied to the packet.

OBJECT-TYPE

Destination IP address to filter on.

OBJECT-TYPE

Destination IP subnet mask to filter on.

OBJECT-TYPE

Source IP address to filter on.

OBJECT-TYPE

Source IP subnet mask to filter on.

OBJECT-TYPE

This filter's unique identifier(id). This id is automatically generated by the system when a filter is created. This id is used in the 'rcIpFilterGlobalListTable' and 'rcIpFilterBaseListTable' when grouping one or more filters into a filter list.

OBJECT-TYPE

This filter's name.

OBJECT-TYPE

Type of protocol to filter on.

OBJECT-TYPE

TCP/UDP source port to filter on.

OBJECT-TYPE

Type of matching to perform on the field 'rcIpFilterSrcPort'. For 'source' and 'destination' filters, this value can only be 'equal(1)'.

OBJECT-TYPE

TCP/UDP destination port to filter on.

OBJECT-TYPE

Type of matching to perform on the field 'rcIpFilterDstPort'. For 'source' and 'destination' filters, this value can only be 'equal(1)'.

OBJECT-TYPE

Used to specify whether a packet matching this filter should be copied to the CPU.

OBJECT-TYPE

Used to specify whether a packet matching this filter should be mirrored to the port specified by 'rcMirrorByPortMirrorPort'.

OBJECT-TYPE

Used to specify whether a packet matching this filter should be forwarded with high priority.

OBJECT-TYPE

Used to specify whether a TCP packet matching this filter should be accepted. Pass only those matching TCP packets with either the ACK bit or RST bit set. Apply only if the IP Protocol is set to TCP.

OBJECT-TYPE

Used to specify the priority bits for explicit IEEE VLAN tag for a packet matching this filter. If this priority bit field is greater than the priority field currently in the IEEE tag in the Packet Header, this priority field will be loaded into the Packet Header.

OBJECT-TYPE

Used to specify whether the 'rcIpFilterPktLimit' field in this entry should be used when applying this filter.

OBJECT-TYPE

The maximum packet size limit to filter against.

OBJECT-TYPE

Row status of this entry.