TIMETRA-PORT-MIB

TEXTUAL-CONVENTION

A TmnxBundleID is a unique 32 bit number encoded as shown below. |32 30| 29 26 | 25 22 | 21 16 | 15 13 | 12 1| +-----+-------+-------+-------+-----------+-------+ |001 | slot | mda | 0 | bndl type | bndlid| +-----+-------+-------+-------+-----------+-------+ The bundle id is unique for a MDA. The bndlid must fall in one of the following ranges depending on MDA type: mda-type range m4-choc3-as-sfp 1-256 m1-choc12-as-sfp 1-256 m12-chds3-as 1-256 m4-chds3-as 1-112 m4-chds3 1-56 m12-chds3 1-56 m1-choc12-sfp 1-56 m4-choc3-sfp 1-56 c8-chds1 1-56 c8-atmds1 1-8 A slot value of 15 (Invalid slot) and mda value of 0 (invalid mda) represents a bundle protection group. Otherwise, the bundle is considered associated with a valid slot and mda. The following bundle types are supported: bndl type value MLPPP 000 IMA 001 MLFR 010

TEXTUAL-CONVENTION

The TmnxCoherentOpticalAlarm specifies the type of coherent optical alarm currently active on the port. The values are logical ORs of TmnxCoherentOpticalDefectPoint. moduleFault - logical OR of defect points 'overTemp(0)', 'hwPost(1)', 'pldFlashInit(2)', 'powerSupply(3)', 'chkSum(4)' module - logical OR of defect points 'refClkIn(5)', 'txJitPllLol(6)', 'txCmuLol(7)', 'txLossFunc(8)', 'hostRxCorr(25)', 'hostRxUncorr(26)' netRx - logical OR of defect points 'netRxLol(10)', 'netRxLos(15)', 'netRxFifoErr(16)', 'netRxTec(17)', 'netRxModemSyncDet(21)', 'netRxModemLock(22)' netTx - logical OR of defect points 'netTxTec(12)', 'netTxWaveUnlk(13)', 'netTxLosf(14)', 'netTxOutOfAlign(18)', 'netTxCmuLock(19)', 'netTxRefClk(20)' hostTx - logical OR of defect points 'hostTxLol(9)', 'hostTxSkewHigh(11)', 'hostTxLaneFifoErr(23)', 'hostTxDeskew(24)'

TEXTUAL-CONVENTION

The TmnxCoherentOpticalDefectPoint specifies the type of coherent optical defects currently active on the port. overTemp - Module over safe operating temperature. hwPost - Hardware fault detected during power-on self-test. pldFlashInit - PLD (Programmable Logic Device), CPLD (Complex Programmable Logic Device), or FPGA (Field Programmable Gate Array) initialization fault. powerSupply - Power supply is out of range. chkSum - CFP (C Form factor Pluggable) table checksum fault. refClkIn - Loss of reference clock. txJitPllLol - TX jitter PLL (Phase-Locked Loop) loss of lock. txCmuLol - TX CMU (Clock Multiplier Unit) loss of lock. txLossFunc - TX loss of signal functionality. hostTxLol - TX IC (Integrated Circuit) lock indicator. netRxLol - RX IC lock indicator. hostTxSkewHigh - Host lane skew out of alignment. netTxTec - Lane TX thermoelectric cooler fault. netTxWaveUnlk - Lane wavelength unlocked. netTxLosf - Lane TX loss of signal functionality netRxLos - Lane RX loss of signal. netRxFifoErr - Lane RX FIFO error. netRxTec - Lane RX thermoelectric cooler fault. netTxOutOfAlign - Out of alignment. netTxCmuLock - CMU lock fault. netTxRefClk - Reference clock fault. netRxModemSyncDet - Modem sync detect fault. netRxModemLock - Modem lock fault. hostTxLaneFifoErr - Lane TX FIFO error. hostTxDeskew - Deskew lock fault. hostRxCorr - Host Rx FEC corrected bits detected. hostRxUncorr - Host Rx FEC uncorrectable error detected.

TEXTUAL-CONVENTION

TmnxCrcPolynomial is enumerated integer type of polynomial options used in load balancing algorithm for distribution of packet flows under ECMP and LAG. poly1(1) - CRC16_0x8003 poly2(2) - CRC16_0x8011 poly3(3) - CRC16_0x8423 poly4(4) - CRC16_0x8101 poly5(5) - CRC16_0x84a1 poly6(6) - CRC16_0x9019.

TEXTUAL-CONVENTION

The TmnxDS1Loopback data type is an enumerated integer that indicates the type of loopback the DS1 port/channel currently is in. A 'line' loopback loops frames received on this port back to the remote system. A 'internal' loopback loops frames from the local system back at the framer. A 'fdlAnsi' requests a line loopback of type FDL ANSI T1.403. A 'fdlBellcore' requests a line loopback of type FDL Bellcore TR-TSY-000312. A 'payloadAnsi' requests a payload loopback of type FDL ANSI T1.403. A 'inbandAnsi' requests a line loopback of type inband ANSI T1.403. A 'inbandBellcore' requests a line loopback of type inband Bellcore TR-TSY-000312.

TEXTUAL-CONVENTION

The TmnxDS3Loopback data type is an enumerated integer that indicates the type of loopback the DS3 port/channel currently is in. A 'line' loopback loops frames received on this port back to the remote system. A 'internal' loopback loops the frames from the local system back at the framer. When the value is set to 'remote', a signal is sent to the remote system to provide a line loopback.

TEXTUAL-CONVENTION

The TmnxDSXBertOperStatus data type is an enumerated integer that indicates the status of Bit Error Rate Test (BERT). When BERT is activated, the status will be 'active'. Otherwise the status will be 'idle' or 'noMdaResources' if the last BERT test could not be executed because of an MDA concurrent BERT test limit.

TEXTUAL-CONVENTION

The TmnxDSXBertPattern data type is an enumerated integer that indicates the pattern used for the Bit Error Rate Test (BERT).

TEXTUAL-CONVENTION

The TmnxDSXClockSource data type is an enumerated type that indicates the clock for transmitted data on a DS3 or DS1 channel. loopTimed(1) - The clock is recovered from the line's receive data stream nodeTimed(2) - The clock is internal adaptive(3) - The clock is adaptively recovered from the rate at which data is received and not from the physical layer. differential(4) - The clock is recovered from differential RTP timestamp header.

TEXTUAL-CONVENTION

The TmnxDSXClockSyncState data type is an enumeration type that indicates the clock synchronization state on a DS3 or DS1 channel. unknown(0) - Unsupported or unknown state normal(1) - Normal (locked) state holdOver(2) - Synchronization with reference has been lost freeRun(3) - Synchronized with internal reference

TEXTUAL-CONVENTION

The TmnxDSXIdleCycleFlags data type is an enumerated integer that indicates the value that the DS3/DS1 port/channel or a DS0 channel group transmits during idle cycle. The value of 'none' is applicable to ATM and CEM ports/channels only, which transmit idle cells and not octets defined by the below values. If the value is set to 'flags', a value of 0x7E is used. If the value is set to 'ones', a value of 0xFF is used.

TEXTUAL-CONVENTION

The TmnxDSXIdleFillType data type is an enumerated integer that indicates the type of data fill that a CEM DS3/DS1 channel or a DS0 channel group plays out when the channel experiences underrun. - The value of 'notApplicable' indicates that this object is not applicable to the channel. - The value of 'allOnes' indicates that all 1's will be played out. - The value of 'userDefinedPattern' indicates that a user defined pattern will be played out.

TEXTUAL-CONVENTION

The TmnxDSXLoopback data type is an enumerated integer that indicates the type of loopback the DS3/DS1 port/channel currently is in.

TEXTUAL-CONVENTION

The TmnxDSXReportAlarm data type indicates the type of TDM alarm: ais - alarm indication signal errors. los - loss of signal errors. oof - out-of-frame errors. rai - resource availability indicator events. looped - far end wants the read end to loopback berSd - DSX bit error signal degradation berSf - DSX bit error signal failure

TEXTUAL-CONVENTION

The TmnxDigitalDiagnosticFailureBits specifies the state of the Digital Diagnostic Monitoring (DDM) SFF thresholds. For each monitored attribute a low-warning, low-alarm, high-warning, and high-alarm are recorded. A set bit indicates the object is in a failed state, a cleared bit indicates the object has not exceeded the threshold.

TEXTUAL-CONVENTION

A list of ds0 timeslots on a DS1 line. The list is specified as an OCTET STRING in which each ds0 timeslot is represented by a single bit, where timeslots 1 through 8 are represented by the bits in the first octet, timeslots 9 through 16 by the bits in the second octet, etc. In each octet, the lowest numbered timeslot is represented by the most significant bit, and the highest numbered timeslot by the least significant bit. A timeslot is present in the list when its bit is 1, and absent when its bit is 0. If the OCTET STRING value has more bits than required to represent the timeslots on a DS1, then the extra bits are ignored.

TEXTUAL-CONVENTION

The TmnxHoldTime specifies the hold-timer for link up/down event dampening. This guards against reporting excessive interface transitions. This is implemented by not advertising subsequent transitions of the interface to upper layer protocols until the configured timer has expired.

TEXTUAL-CONVENTION

The TmnxImaGrpClockModes lists the types of clock modes available to IMA Groups.

TEXTUAL-CONVENTION

The TmnxImaGrpFailState indicates the failure reason of an IMA group.

TEXTUAL-CONVENTION

The TmnxImaGrpState indicates the current state of the IMA Group State Machine.

TEXTUAL-CONVENTION

The TmnxImaGrpVersion lists the types of Ima versions available per IMA Groups.

TEXTUAL-CONVENTION

The TmnxImaLnkFailState indicates the local failure status of a link belonging to an IMA group.

TEXTUAL-CONVENTION

The TmnxImaLnkState indicates the current state of an IMA link.

TEXTUAL-CONVENTION

The TmnxImaTestState indicates the current state of the test pattern procedure.

TEXTUAL-CONVENTION

The TmnxMcMlpppClassIndex indicates the class of a Multiclass MLPPP bundle. For Multiclass MLPPP bundles with a non-zero tmnxBundleMlpppClassCount of classes, class index takes valid values from 0 to (tmnxBundleMlpppClassCount - 1) inclusive. For example a 4-class MLPPP bundle has 4 classes with indices 0, 1, 2, and 3.

TEXTUAL-CONVENTION

TmnxMlfrLinkDownReason indicates the reason code for marking a MLFR member link of a bundle to down. A 'none' down reason indicates that the link is active. An 'outOfService' down reason indicates that the link operational status is down. A 'redDiffDelayExceeded' down reason indicates that the differential delay of the link exceeded the configured value of red differential delay and the delay action was configured as 'down'. A 'loopback' down reason indicates that the link has been detected to be in a loopback condition. A 'negotiating' down reason indicates that the link has not successfully negotiated the link into a bundle. A 'noRxHelloAck' down reason indicates that the link has not received a hello ack response. A 'rxCause' down reason indicates that a peer failure has been detected on this link. A 'txCause' down reason indicates that a local failure has been detected on this link. A linkReset' down reason indicates that the link is being reset.

TEXTUAL-CONVENTION

TmnxMlpppEndpointIdClass indicates the MLPPP Endpoint Discriminator Class Field Type.

TEXTUAL-CONVENTION

The TmnxOpticalAmpAlarm specifies the alarms which are enabled or outstanding against an interface that is equipped with an optical amplifier. The valid alarms are as follows: - ampIld - Amplifier Pump over-current. - ampTmp - Amplifier Pump temperature. - ampMth - Amplifier Module Case temperature high. - ampMtl - Amplifier Module Case temperature low. - ampLos - Amplifier Loss of input optical power. - ampLop - Amplifier Loss of output power. - ampCom - Amplifier Module communication failure.

TEXTUAL-CONVENTION

The TmnxOpticalAmpCtrlState specifies the state of the control loop that optimizes the receive optical power of to the MSA optics.

TEXTUAL-CONVENTION

The TmnxOpticalDispCtrlMode specifies the operational control mode of the dispersion compensation module. The valid modes are as follows: - automatic - The software control loop automatically determines the dispersion using a FEC feedback algorithm to find the best operational dispersion compensation point - manual - The software control loop is disabled and the user manually configures the dispersion compensation.

TEXTUAL-CONVENTION

TmnxOpticalDwdmChannel is the DWDM ITU channel associated with an optical interface. It is expressed in a form that is derived from the laser's operational frequency. For example 193.40 THz corresponds to DWDM ITU channel 34 in the 100 GHz grid and 193.45 THz corresponds to DWDM ITU channel 345 in the 50 GHz grid. Range ITU Grid -------- ---------------------- 17-61 100 GHz Grid 170-610 50 GHz Grid For configurable attributes, the value 0 represents no channel. For read-only attributes, the value 0 represents no channel transmitted or the interface is not equipped with a laser.

TEXTUAL-CONVENTION

TmnxOpticalDwdmExtendedChannel is the extended DWDM ITU channel associated with an optical interface. It is expressed in a form that is derived from the laser's operational frequency. For example 193.40 THz corresponds to DWDM ITU channel 34 in the 100 GHz grid and 193.45 THz corresponds to DWDM ITU channel 345 in the 50 GHz grid. Range ITU Grid -------- ---------------------- 11-62 100 GHz Grid 115-615 50 GHz Grid For configurable attributes, the value 0 represents no channel. For read-only attributes, the value 0 represents no channel transmitted or the interface is not equipped with a laser.

TEXTUAL-CONVENTION

The TmnxOpticalTdcmAlarm specifies the alarms which are enabled or outstanding against an interface that is equipped with a tunable dispersion compensation module. The valid alarms are as follows: - tdcmNotRdy - Tdcm not ready. - tdcmMth - Tdcm module temperature high. - tdcmMtl - Tdcm module temperature low. - tdcmUnLck - Tdcm thermal control unlocked. - tdcmTmpLim - Tdcm thermal control temperature limit. - tdcmEprInv - Tdcm EEPROM invalid. - tdcmCom - Tdcm module communication failure.

TEXTUAL-CONVENTION

The TmnxOpticalTdcmCtrlState specifies the state of the control loop that optimizes the dispersion by tuning the dispersion compensation module to the set point at which the FEC corrected error rate is the lowest.

TEXTUAL-CONVENTION

The TmnxPortClass data type is an enumerated integer that describes the values used to identify the class of interface provided by this port.

TEXTUAL-CONVENTION

The TmnxPortCompatMode specifies the optical mode and rate of operation of the Coherent interface. Code points: longHaul - interface will operate in the native long haul mode metro - interface will operate in the native metro regional mode access - interface will operate in the native access mode - 80km reach interop - interface will operate in the third party interop mode interop2 - interface will operate in the third party interop mode with alternate differential encoding interop3 - interface will operate in the CFP2-DCO Rev A0 Staircase FEC interop mode longHaulNonDiff - interface will operate in the native long haul mode using non-differential encoding

TEXTUAL-CONVENTION

TmnxPortConnectorBreakoutType is an index into the tmnxPortConnBreakoutTypeTable used to identify a specific type of connector breakout.

TEXTUAL-CONVENTION

TmnxPortConnectorType is an index into the tmnxPortConnectTypeTable used to identify a specific type of port connector.

TEXTUAL-CONVENTION

The type of encapsulation protocol configured on a port's network interface. When the encap type has a value of 'nullEncap', frames received will not carry any tags or labels and as a result only one service can be configured on this port. Sometimes this is referred to as raw Ethernet packets. When the encap type has a value of 'qEncap', ingress frames carry 802.1q tags where each different tag can signify a different service. This is not a valid value if tmnxPortClass has a value of 'sonetPath'. When the encap type has a value of 'bcpNullEncap', BCP is used on the SONET path as the NCP control protocol. The BCP IEEE 802 Tagged Frame Configuration Option (type 8) is negotiated to 'enabled'. VLAN tagged frames are allowed into the SONET path. Only a single SAP can be associated with the SONET path. 'bcpNullEncap' is valid only if tmnxPortClass has a value of 'sonetPath'. When the encap type has a value of 'bcpDot1qEncap', BCP is used as the NCP control protocol. The BCP IEEE 802 Tagged Frame Configuration Option (type 8) is negotiated to 'enabled'. VLAN tagged frames are allowed on the SONET path. This encapsulation type is required when multiple SAPs are defined on the SONET path where each one is service delimited by a provisioned Dot1q tag. When 'bcpDot1qEncap' is specified, BCP does not enter the 'open' state unless the far end peer also supports 'bcpDot1qEncap'. This allows a LCP negotiation to transmit configuration request and confirmation messages to enable this feature. 'bcpDot1qEncap' is a valid value only if tmnxPortClass has a value of 'SONET'. When the encap type has a value of 'ipcpEncap', BCP will not be used on this SONET path. IPCP NCP is used instead. 'ipcpEncap' is a valid only if tmnxPortClass has a value of 'sonetPath'. When the encap type has a value of 'frEncap', Frame Relay is the expected encapsulation. When the encap type has a value of 'pppAutoEncap', IPCP is automatically enabled. This encap type is only valid on ports/paths in network mode. When the encap type has a value of 'atmEncap', the encapsulation on the port is ATM. The 'atmEncap' is also used when mirroring ATM ports. When the encap type has a value of 'wanMirrorEncap', the port is used for mirroring of frame relay and POS ports. On such ports no link management protocol would run. When the encap type has a value of 'ciscoHDLCEncap', the Cisco HDLC encapsulation is applied. This encap type is only valid if TmnxPortClass has a value of 'tdm' or 'sonet'. When the encap type has a value of 'cemEncap', encapsulation of frames will be circuit emulation. This is used to support transparent transmission of frames. This encap type is only valid if TmnxPortClass has a value of 'tdm' or 'sonet' in access mode. When the encap type has a value of 'rawEncap', data does not necessarily carry any tags, headers or any other form of delimiter. This encap type is only valid on access ports supporting serial data. When the encap type has a value of 'cellularEncap', packets on the port use cellular encapsulation. This encapsulation is only valid if the port's tmnxPortType indicates that the port is a 'Cellular' port.

TEXTUAL-CONVENTION

The TmnxPortEtherMonReportStatus is a bitmask that describes alarms that can be raised/cleared on an Ethernet Port used in Monitoring. The possible values are: sdThresholdExceeded (0)-- Signal Degradation exceeded the threshold. sfThresholdExceeded (1)-- Signal Failure exceeded the threshold.

TEXTUAL-CONVENTION

The TmnxPortEtherMonReportValue is an enumerated integer that describes the values used to identify the reason an alarm has been raised for a fault in Monitoring on an Ethernet Port. TmnxPortEtherMonReportStatus defines the valid alarm values.

TEXTUAL-CONVENTION

The TmnxPortEtherOperPhyTxClock data type is an enumerated integer that indicates the result of the master/slave resolution on copper based Ethernet ports running at 1 Gbps. - The value of 'notApplicable' indicates that this object is not applicable to this port. - The value of 'master' indicates that the port is the timing master for the link partner. - The value of 'slave' indicates that the port is timing slave to the link partner.

TEXTUAL-CONVENTION

The TmnxPortEtherReportStatus is a bitmask that describes alarms that can be raised/cleared on an Ethernet Port. The possible values are: notUsed (0) - not applicable signalFailure(1) - Ethernet signal lost alarm When the optic module declares a loss of signal, the MAC will declare localFault(3) and the PCS will declare noBlockLock(6). remoteFault (2) - Remote Fault See localFault(3). localFault (3) - Local Fault Defined in IEEE 802.3ba Clause 81.3.4. When the PCS detects a fault it generates a localFault(3) towards the MAC layer. The MAC layer responds by sending a remoteFault(2) to the far end. A local fault can get caused by any of the PCS layer defects below. noFrameLock (4) - Not locked on the Ethernet framing sequence Defined in IEEE 802.3ba Clause 82.2.13. The frame lock is obtained when all lanes have 64B/66B block sync, been deskewed, and alignment marker lock. highBer (5) - High Bit Error Rate Defined in IEEE 802.3ba Clause 82.2.18.2.2. Bit error ratio > 10^-4. noBlockLock (6) - 40G/100G PCS Lanes Not Block Locked Defined in IEEE 802.3ba Clause 82.2.11. Cleared once all lanes have 64B/66B block lock. noAmLock (7) - 40G/100G PCS Alignment Marker Loss of Lock Defined in IEEE 802.3ba Clause 82.2.12. Cleared once all lanes alignment marker lock. duplicateLane(8) - 40G/100G PCS Duplicate Lane Marker Not defined in the standard. Raised when two or more lanes are seen with the same alignment marker.

TEXTUAL-CONVENTION

The TmnxPortEtherReportValue is an enumerated integer that describes the values used to identify the reason an alarm has been raised on an Ethernet Port. The possible values are: notUsed (0) - not applicable signalFailure(1) - Ethernet signal lost alarm When the optic module declares a loss of signal, the MAC will declare localFault(3) and the Physical Coding Sublayer (PCS) will declare noBlockLock(6). remoteFault (2) - Remote Fault See localFault(3). localFault (3) - Local Fault Defined in IEEE 802.3ba Clause 81.3.4. When the PCS detects a fault it generates a localFault(3) towards the MAC layer. The MAC layer responds by sending a remoteFault(2) to the far end. A local fault can get caused by any of the PCS layer defects below. noFrameLock (4) - Not locked on the Ethernet framing sequence Defined in IEEE 802.3ba Clause 82.2.13. The frame lock is obtained when all lanes have 64B/66B block sync, been deskewed, and alignment marker lock. highBer (5) - High Bit Error Rate Defined in IEEE 802.3ba Clause 82.2.18.2.2. Bit error ratio > 10^-4. noBlockLock (6) - 40G/100G PCS Lanes Not Block Locked Defined in IEEE 802.3ba Clause 82.2.11. Cleared once all lanes have 64B/66B block lock. noAmLock (7) - 40G/100G PCS Alignment Marker Loss of Lock Defined in IEEE 802.3ba Clause 82.2.12. Cleared once all lanes alignment marker lock. duplicateLane(8) - 40G/100G PCS Duplicate Lane Marker Not defined in the standard. Raised when two or more lanes are seen with the same alignment marker.

TEXTUAL-CONVENTION

The TmnxPortLosReaction specifies the type of action that is taken in the event of a Loss Of Signal (LOS). The valid modes are as follows: - none - Specifies that the interface not be taken down on crossing the optical LOS threshold. - squelch - Specifies that the interface be taken down on crossing the optical LOS threshold.

TEXTUAL-CONVENTION

The current operational status of this port.

TEXTUAL-CONVENTION

The TmnxPortOptComplianceExtType is an enumerated integer that extends the tmnxPortOpticalCompliance field of of a small form factor (SFF) that is inserted into the port

TEXTUAL-CONVENTION

The state level of this port. A value of 'none' indicates the port is either in its initial creation state or is just about to be deleted. A value of 'ghost' represents a port that is not physically present. This state may represent a pre-provisioned port. A value of 'linkDown' represents a port that is physically present but does not have a link. The 'linkUp' state represents a port that is physically present and has physical link present. A port in 'up' state is ready to pass some kinds of traffic. The tmnxPortUpProtocols variable indicates the actual type(s) of traffic that can be passed on this 'up' link. The 'diagnose' state represents the port undergoing diagnostic test.

TEXTUAL-CONVENTION

TmnxPortType is an index into the tmnxPortTypeTable used to identify a specific type of hardware port.

TEXTUAL-CONVENTION

The programmed setting of a Serial control lead.

TEXTUAL-CONVENTION

The programmed monitor setting of a Serial control lead.

TEXTUAL-CONVENTION

The TmnxSFFStatus specifies the operational status of the small form factor (SFF) that is inserted into the port. If the SFF is removed from the port, the value of TmnxSFFStatus will be 'not-equipped (0)', otherwise 'operational (1)' if no failure is detected. A failure to read the SFF data will result in a 'read-error (2)', while corrupted information on the SFF will result in either 'data-corrupt (3)', or 'ddm-corrupt (4)' if an SFF read results in invalid data or DDM information respectively. An insertion of an unsupported SFF will result in 'unsupported (5)'. An insertion of an SFF device that is preventing other devices from being read will result in the state 'culprit (6)' for the offending device, and 'blocked (7)' for the other devices. A trap will be raised if the value of TmnxSFFStatus indicates a failure; that is the TmnxSFFStatus is neither 'not-equipped (0)', nor 'operational (1)'.

TEXTUAL-CONVENTION

The TmnxWaveTrackerAlarm specifies the alarms which are enabled or outstanding against a Wave Tracker enabled interface. The valid alarms are as follows: - encFail - Encoder Failure. - encDegr - Encoder Degrade. - pwrFail - Power Control Failure. - pwrDegr - Power Control Degrade. - pwrHigh - Power Control High limit reached. - pwrLow - Power Control Low limit reached. - missing - Missing pluggable VOA.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

The value of sysUpTime when the tmnxPortTable was last changed.

OBJECT-TYPE

The port table has an entry for each port on each IOM card in each chassis in the TMNX system.

OBJECT-TYPE

Each row entry represents a port on a IOM card in a chassis in the system. Entries cannot be created and deleted via SNMP SET operations. Before an IOM tmnxMDAEntry can be deleted from the tmnxMDATable, its supported tmnxPortEntry rows must be in the proper state for removal.

OBJECT-TYPE

tmnxPortPortID is an index into this table. It maps this port to its entry in the mib-2 interfaces table.

OBJECT-TYPE

The tmnxPortLastChangeTime variable contains the sysUpTime value of the most recently modified writable variable in the tmnxPortEntry row for this port.

OBJECT-TYPE

The type of port or optical pack installed.

OBJECT-TYPE

The class of port or optical pack installed. This can be derived from tmnxPortType.

OBJECT-TYPE

A textual string containing user supplied information about the interface.

OBJECT-TYPE

The textual name of the interface. The value of this object should be the name of the interface as assigned by the local device and should be suitable for use in commands entered at the device's `console'. This might be a text name, such as `le0' or 'sys171-2/1.

OBJECT-TYPE

This object is an 'alias' name for the interface as specified by a network manager, and provides a non-volatile 'handle' for the interface. On the first instantiation of an interface, the value of tmnxPortAlias associated with that interface is the zero-length string. As and when a value is written into an instance of tmnxPortAlias through a network management set operation, then the agent must retain the supplied value in the tmnxPortAlias instance associated with the same interface for as long as that interface remains instantiated, including across all re- initializations/reboots of the network management system.

OBJECT-TYPE

When tmnxPortUserAssignedMac has a value of 'true', the value of tmnxPortMacAddress has been explicitly assigned by a SNMP SET request. When tmnxPortUserAssignedMac is set to 'false', tmnxPortMacAddress returns the system assigned MAC address.

OBJECT-TYPE

When tmnxPortUserAssignedMac has a value of 'true', tmnxPortMacAddress has the value that has been explicitly assigned by a SNMP SET request. When tmnxPortUserAssignedMac has a value of 'false', tmnxPortMacAddress returns the same value as tmnxPortHwMacAddress, the hardware or system assigned MAC address. When tmnxPortMacAddress is modified by a SET request, the agent sets tmnxPortUserAssignedMac to 'true'. Setting tmnxPortMacAddress to all zeros causes the agent to revert to using the default tmnxPortHwMacAddress and also to return tmnxPortUserAssignedMac as 'false'.

OBJECT-TYPE

The interface's hardware or system assigned MAC address at its protocol sub-layer. When tmnxPortUserAssignedMac has a value of 'true', the value of tmnxPortMacAddress is used instead of tmnxPortHwMacAddress. In the case of a pre-provisioned port that is not yet physically in the system, the MAC address may not be known. In this case a MAC address of all zeros is returned.

OBJECT-TYPE

The tmnxPortMode variable indicates if the interface on this port is configured as a service access port, a network port or a hybrid port. Once the port's mode has been configured for 'access', 'network' or 'hybrid' mode, multiple services may be configured on the port. tmnxPortEncapType is defaulted based on MDA type and Port Mode according to the following table: MDA Type Port Mode tmnxPortEncapType --------------------------------------------------------- ATM access atmEncap CEM access cemEncap Ethernet access nullEncap network nullEncap hybrid qEncap ISA isa-aa network nullEncap isa-bb access qinqEncap network qEncap isa-ipsec access qEncap isa-video access qEncap Sonet/SDH access bcpNullEncap network pppAutoEncap TDM access bcpNullEncap network pppAutoEncap VSM vsm-cca access qEncap vsm-cca network qEncap

OBJECT-TYPE

The value of tmnxPortEncapType specifies the type of encapsulation protocol configured on this port's network interface. tmnxPortEncapType is set to 'unknown' for physical SONET/SDH and TDM ports. If the port mode equals 'hybrid', tmnxPortEncapType can only be set to 'qEncap' or 'qinqEncap'.

OBJECT-TYPE

The value of tmnxPortLagId specifies which LAG or multi-link trunk (MLT) this port is assigned to. If this port is not associated with any LAG, this value will be set to zero(0). The maximum value of this object is '64', when the value of TIMETRA-CHASSIS-MIB::tmnxChassisType is '5' (ESS-1/SR-1).

OBJECT-TYPE

The value of tmnxPortHoldTimeUp is used to configure the hold-timer for link up event dampening. A value of zero (0) indicates that an up transition is reported immediately. The value of tmnxPortHoldTimeUp is not applicable when tmnxPortClass has a value of 'sonet (5)' or tmnxPortType has a value of 'portTypeDS3E3'. In these cases, tmnxSonetHoldTimeUp and tmnxDS3HoldTimeUp are used, respectively. tmnxPortHoldTimeUp is measured in units as specified by tmnxPortHoldTimeUnits. If the value of tmnxPortHoldTimeUnits is 'centisenconds(1)', the value must be specified in multiples of 5. The maximum hold-time for this object is 10 hours, regardless of the units specified. Attempts to change the maximum value to a hold-time longer than 10 hours will result in an 'inconsistentValue' error.

OBJECT-TYPE

The value of tmnxPortHoldTimeDown is used to configure the hold-timer for link down event dampening. A value of zero (0) indicates that a down transition is reported immediately. The value of tmnxPortHoldTimeDown is not applicable when tmnxPortClass has a value of 'sonet (5)' or tmnxPortType has a value of 'portTypeDS3E3'. In these cases, tmnxSonetHoldTimeDown and tmnxDS3HoldTimeDown are used, respectively. tmnxPortHoldTimeDown is measured in units as specified by tmnxPortHoldTimeUnits. If the value of tmnxPortHoldTimeUnits is 'centisenconds(1)', the value must be specified in multiples of 5. The maximum hold-time for this object is 10 hours, regardless of the units specified. Attempts to change the maximum value to a hold-time longer than 10 hours will result in an 'inconsistentValue' error.

OBJECT-TYPE

The tmnxPortUpProtocols variable is a bitmap that indicates what protocols can be used on this port type.

OBJECT-TYPE

The type of connector installed on this port.

OBJECT-TYPE

Type of the transceiver.

OBJECT-TYPE

The code for the transmission media. tmnxPortOpticalCompliance is used instead of tmnxPortTransceiverCode.tmnxPortOpticalCompliance contains the same information and is defined by an industry standard.

OBJECT-TYPE

The light wavelength transmitted by the transceiver's laser. A value of zero indicates that the port is not equipped with the transceiver. A value in the range of 1 to 2000 indicates that the units are in nanometers (nm). A value in the range of 850000 to 2000000 indicates that the units are in picometers (pm).

OBJECT-TYPE

Indicates if the transceiver is capable of doing diagnostics.

OBJECT-TYPE

The value of tmnxPortTransceiverModelNumber indicates the model information for the transceiver, as read from the transceiver EEPROM. For example, the string may contain the Nokia part number and CLEI for the transceiver. The string is expected to contain printable ASCII characters, but unprintable ASCII characters read from the EEPROM are not filtered out.

OBJECT-TYPE

The external connector provided on the interface.

OBJECT-TYPE

The vendor organizationally unique identifier field (OUI) contains the IEEE company identifier for the vendor. A value of all zero indicates that the vendor OUI is unspecified.

OBJECT-TYPE

The vendor's date code.

OBJECT-TYPE

The value of tmnxPortSFPMedia indicates the media supported for the SFF (Small Form Factor).

OBJECT-TYPE

The value of tmnxPortSFPEquipped indicates if the SFF is equipped.

OBJECT-TYPE

Indicates if there is an optics pack installed in this port or not.

OBJECT-TYPE

Indicates whether or not the port has a physical link.

OBJECT-TYPE

The desired administrative status of this port. When tmnxPortType references a row in the tmnxPortTypeTable where tmnxPortTypeName is the octet string 'Application Assurance', an attempt to set tmnxPortAdminStatus to a value other than 'inService' results in an 'inconsistentValue' error.

OBJECT-TYPE

The current operational status of this port.

OBJECT-TYPE

The state level of this port. A value of 'none' indicates the port is either in its initial creation state or is just about to be deleted. A value of 'ghost' represents a port that is not physically present. This state may represent a pre-provisioned port. A value of 'linkDown' represents a port that is physically present but does not have a link. The 'linkUp' state represents a port that is physically present and has physical link present. A port in 'up' state is ready to pass some kinds of traffic. The tmnxPortUpProtocols variable indicates the actual type(s) of traffic can be passed on this 'up' link.

OBJECT-TYPE

The tmnxPortPrevState indicates the state level that the port transitioned from into the current tmnxPortState level.

OBJECT-TYPE

The number of alarms currently outstanding on this port.

OBJECT-TYPE

The value of tmnxPortAlarmState indicates the current alarm state for this port.

OBJECT-TYPE

The value of tmnxPortLastAlarmEvent indicates the object name and instance value that points to the row entry in the ALARM-MIB containing the most recent alarm associated with this port. If tmnxPortAlarmState has a value of 'alarmCleared(2)', the most recent alarm event will be in the cleared alarm table. If it has a value of 'alarmActive(1)', the most recent alarm event will be in the active alarm table. If the value of tmnxPortLastAlarmEvent is '0.0', either no port alarm events have occurred since the system was last booted, or the last port alarm event has aged out and its entry is no longer available in the ALARM-MIB tables.

OBJECT-TYPE

Setting this action variable causes all the alarms associated with this port to be moved from the current alarm log to the history alarm log. Primarily meant for use in development. This object will most likely be removed from the MIB before product release.

OBJECT-TYPE

The value of tmnxPortSFPVendorSerialNum indicates the transceiver's vendor serial number in ASCII characters, as read from the transceiver EEPROM. An empty string indicates the vendor serial number is unspecified. The string is expected to contain printable ASCII characters, but unprintable ASCII characters read from the EEPROM are not filtered out.

OBJECT-TYPE

The value of tmnxPortSFPVendorPartNum indicates the transceiver's vendor part number (or product name) in ASCII characters, as read from the transceiver EEPROM. An empty string indicates the vendor part number is unspecified. The string is expected to contain printable ASCII characters, but unprintable ASCII characters read from the EEPROM are not filtered out.

OBJECT-TYPE

The tmnxPortLastStateChanged variable contains the value of the sysUpTime the last time the operational status of the port changed state.

OBJECT-TYPE

For SONET/SDH paths or TDM channels, tmnxPortNumChannels contains the number of possible immediate children. For leaf paths or channels, the value of this object will be zero. For SONET/SDH or TDM physical ports, tmnxPortNumChannels contains the total number of channels on the physical port. For all other entries in the tmnxPortTable, the value of this object will be zero.

OBJECT-TYPE

tmnxPortNetworkEgrQueues contains the network egress queue policy if the tmnxPortMode is network. Otherwise this object has no significance.

OBJECT-TYPE

tmnxPortBundleNumber identifies the bundle for which this port is a member. If this port is not a member of any bundle, the value of tmnxPortBundleNumber will be zero.

OBJECT-TYPE

tmnxPortIsLeaf is applicable only when the 'isSonet' and/or 'isTDM' bits in TIMETRA-CHASSIS-MIB:tmnxMDACapabilities are set. When the value of this object is 'true', it indicates that the channel is capable of passing traffic. The value of this object is 'false' for: 1. Physical ports on SONET/TDM MDA's 2. Intermediate channels on a channelized MDA 3. Leaf channels which belong to a bundle For ports on Ethernet MDA's or for LAG ports, the value of this object will be 'false'.

OBJECT-TYPE

tmnxPortChanType is applicable only when the 'isSonet' and/or 'isTDM' bits in TIMETRA-CHASSIS-MIB:tmnxMDACapabilities are set. It indicates the type of the channel. For ports on Ethernet MDA's, the value of this object will be 'unknown'.

OBJECT-TYPE

tmnxPortParentPortID is applicable only when the 'isSonet' and/or 'isTDM' bits in TIMETRA-CHASSIS-MIB:tmnxMDACapabilities are set. For SONET or TDM channel, it indicates the port ID of its parent channel or port.

OBJECT-TYPE

The value of tmnxPortOpticalCompliance indicates the 8 bytes of optical compliance bits stored in SFF EEPROMs. tmnxPortOpticalCompliance is applicable only when the value of tmnxPortSFPEquipped is set to 'true'.

OBJECT-TYPE

The value of tmnxPortLoadBalanceAlgorithm specifies the load balancing algorithm to be used on this port. When the value is 'includeL4', the src and dst port are used in the hashing algorithm. When it's 'excludeL4', they are not included. When the value is 'default', the port inherits the global settings in tmnxL4LoadBalancing. The value is 'notApplicable' for ports that do not pass any traffic. An attempt to modify this object when it is set to 'notApplicable' will return an inconsistentValue error.

OBJECT-TYPE

The value of tmnxPortEgrPortSchedPlcy specifies the egress QoS port scheduler policy for this port. This object must correspond to the index of a row in TIMETRA-QOS-MIB::tPortSchedulerPlcyTable. A non-empty value for tmnxPortEgrPortSchedPlcy is only valid when the tmnxMDAAssignedType is a non-HSMDA MDA Type. Attempting to set tmnxPortEgrPortSchedPlcy to a non-empty string when the tmnxMDAAssignedType is a HSMDA MDA Type will return an 'inconsistentValue' error.

OBJECT-TYPE

The value of tmnxPortLastClearedTime indicates the sysUpTime when the counters in the IF-MIB:ifTable were last cleared.

OBJECT-TYPE

The value of tmnxPortEgrHsmdaSchedPlcy specifies the egress QoS HSMDA scheduler policy for this port. This object must correspond to the index of a row in TIMETRA-QOS-MIB::tHsmdaSchedulerPlcyTable, otherwise an 'inconsistentValue' error will be returned. When the tmnxMDAAssignedType is a non-HSMDA MDA Type, the value for tmnxPortEgrHsmdaSchedPlcy will be ignored. If the tmnxMDAAssignedType is a HSMDA MDA Type, the default for this object will be the string 'default'.

OBJECT-TYPE

The value of tmnxPortIngNamedPoolPlcy specifies a named pool policy associated with an port ingress context. The policy governs the way named pools are created at the port level. This object is obsoleted in 20.0 Release.

OBJECT-TYPE

The value of tmnxPortEgrNamedPoolPlcy specifies a named pool policy associated with an port egress context. The policy governs the way named pools are created at the port level. This object is obsoleted in 20.0 Release.

OBJECT-TYPE

The value of tmnxPortIngPoolPercentRate specifies increment or decrement of the active bandwidth associated with the ingress port. This active bandwidth affects the amount of ingress buffer space managed by the port.

OBJECT-TYPE

The value of tmnxPortEgrPoolPercentRate specifies increment or decrement of the active bandwidth associated with the egress port. This active bandwidth affects the amount of egress buffer space managed by the port. The table below summarizes cases when the default value of tmnxPortEgrPoolPercentRate differs from 100. port behavior default value ------------------------------------ ISA-AA /to-sub 1000 ISA-AA /fm-sub 500

OBJECT-TYPE

The value of tmnxPortDDMEventSuppression specifies whether or not an inserted SFF that supports Digital Diagnostic Monitoring raises traps and events (false) or suppresses all notifications (true).

OBJECT-TYPE

The value of tmnxPortSFPStatus indicates the operational status of the inserted SFF. If tmnxPortSFPEquipped is false, the tmnxPortSFPStatus will be 'not-equipped (0)', otherwise 'operational (1)' if no failure is detected.

OBJECT-TYPE

The tmnxPortReasonDownFlags indicates why a port may be in the operationally 'down' state. The following reasons are detected through this object: unknown(0) - Unspecified (or unknown) linklossFwd(1) - A sap using this port has an LLF operational status set to 'fault' lagMemberPortStandby(2) - A lag using this port as a member port has set the member port to 'standby' while configured to keep standby member ports down. ethCfmFault(3) - A facility MEP bound to this port has its dot1agCfmMepHighestPrDefect set to a value other than 'none (0)'. opticalTuning(4) - The DWDM optical receive signal is undergoing tuning and analysis by control algorithms to find the optimal settings. channelOutOfRange(5) - The configured DWDM optical channel is out of range for the equipped tunable optical interface. channelNotConfigured(6) - The DWDM optical channel is not configured for the equipped tunable optical interface. crcError(7) - CRC errors on the port exceeded the configured threshold. internalMacTxError(8) - An internal MAC tx error was detected on the port. efmOamDown(9) - dot3OamOperStatus is not 'operational'. symMonError(10) - Symbol Monitor Errors on the port exceeded the configured threshold. satHostPortDown(12) - The host port for this satellite uplink port is down. satUplinkPortDown(13) - The active satellite uplink port for this satellite client port is down.

OBJECT-TYPE

tmnxPortSSMRxQualityLevel indicates the SSM quality level of received SSM messages. On ports not supporting SSM, or not receiving SSM messages, the quality level will be 'unknown (0)'. The values 'prs (1)' through 'dus (9)' and 'pno (16)' correspond to quality levels defined in GR-253-CORE. The values 'prc (10)' through 'inv (15)' correspond to quality levels defined in G.781. The values 'eec1 (17)' and 'eec2 (18)' correspond to quality levels defines in G.8264. The value 'failed (19)' is used when there is a failure in the SSM channel.

OBJECT-TYPE

tmnxPortDwdmLaserChannel specifies the DWDM ITU channel at which a tunable optical interface will be configured to operate. A value of zero(0) can be specified only on an administratively disabled port or a port that is equipped with a non-tunable laser. To enable a port that is equipped with a tunable laser, tmnxPortDwdmLaserChannel must be changed to a valid DWDM ITU channel number in either the 50GHz, or 100GHz grid.

OBJECT-TYPE

The value of tmnxPortOtuCapable indicates whether or not the physical port supports the Optical Transport Unit (OTU) encapsulation.

OBJECT-TYPE

The value of tmnxPortWaveTrackerCapable indicates whether or not the physical port supports Wavelength Tracker. tmnxPortWaveTrackerCapable is equivalent to 'tnWtEncodePortCapabilityPresent' of the 1696-Roadm MIBs.

OBJECT-TYPE

The value of tmnxPortHybridIngAccessWeight specifies the increment or decrement of the ingress access weight associated with the port. This active weight affects the amount of ingress access buffer space managed by the port. This object only applies when tmnxPortMode is set to 'hybrid (3)'

OBJECT-TYPE

The value of tmnxPortHybridIngNetworkWeight specifies the increment or decrement of the ingress network weight associated with the port. This active weight affects the amount of ingress network buffer space managed by the port. This object only applies when tmnxPortMode is set to 'hybrid (3)'

OBJECT-TYPE

The value of tmnxPortHybridEgrAccessWeight specifies the increment or decrement of the egress access weight associated with the port. This active weight affects the amount of egress access buffer space managed by the port. This object only applies when tmnxPortMode is set to 'hybrid (3)'

OBJECT-TYPE

The value of tmnxPortHybridEgrNetworkWeight specifies the increment or decrement of the egress network weight associated with the port. This active weight affects the amount of egress network buffer space managed by the port. This object only applies when tmnxPortMode is set to 'hybrid (3)'

OBJECT-TYPE

The value of tmnxPortDwdmRxDtvAdjustEnable specifies whether or not the Receive Decision threshold voltage adjustment feedback loop should be enabled. When this value is set to false, the optical receiver's default receive decision threshold voltage will be used.

OBJECT-TYPE

The value of tmnxPortDwdmRxDtvDacPercent indicates the current relative adjustment of the receive decision threshold voltage in hundredths of a percent. 50.00% is the optical receiver's default decision threshold voltage.

OBJECT-TYPE

The value of tmnxPortInterfaceGroupHandlerIdx indicates whether or not the physical port is a member of an Interface Group Handler.

OBJECT-TYPE

The value of tmnxPortHoldTimeUnits specifies the measurable units of tmnxPortHoldTimeDown and tmnxPortHoldTimeUp.

OBJECT-TYPE

The value of tmnxPortLinkLengthInfo indicates the link length info stored in SFF EEPROMs. tmnxPortLinkLengthInfo is applicable only when tmnxPortSFPEquipped is 'true'; otherwise, all 6 bytes will have a value of '0'. See SFF Committee documents for details on the representation of the values in each byte. For SFP EEPROMs, the 6 bytes are bytes 14 to 19 of the A0 bank inclusive, described in SFF Committee document SFF-8472. For XFP EEPROMs, the first 5 bytes are bytes 142 to 146 of the 01 bank inclusive, described in SFF Committee document INF-8077i. For XFP EEPROMs, byte 6 will have a value of '0'.

OBJECT-TYPE

The value of tmnxPortSFPNumLanes indicates the total number of lanes supported by the CSFP/QSFP. If tmnxPortSFPEquipped is false, this object will have a value of '0'.

OBJECT-TYPE

The value of tmnxPortPhysStateChangeCount indicates the number of times a physical port state has changed from 'linkDown (3)' to either 'linkUp (4)' or 'up (5)' and from either 'linkUp (4)' or 'up (5)' to 'linkDown (3)'. The count does not include transitions between 'linkUp (4)' and 'up (5)'. This counter is applicable to physical Ethernet and Cellular ports only. All other ports maintain a count of 0. This object is automatically reset to zero, once the port enters the 'ghost (2)' state. To reset this object manually, one may use the tmnxClearTable entry whose tmnxClearName value is 'clearPortPhysStateChangeCount' by specifying the tmnxClearParams value with 'port-id=<ifIndex>'.

OBJECT-TYPE

The value of tmnxPortFarEndId indicates which port identifier is connected to tmnxPortPortID.

OBJECT-TYPE

The value of tmnxPortEgrMonitorPortSched specifies whether to enable monitoring of port scheduler specified by tmnxPortEgrPortSchedPlcy.

OBJECT-TYPE

The value of tmnxPortMonitorAggEgrQueueStats specifies whether to enable the monitoring of aggregate egress queue statistics on the port. All queues on the port are monitored, which includes SAP egress, network egress, subscriber egress, egress queue-group queues and system queues used for sending port related protocol packets.

OBJECT-TYPE

The value of tmnxPortOptComplianceExtension indicates the optical compliance extension stored in SFF EEPROMs. tmnxPortOptComplianceExtension is only applicable when the value of tmnxPortSFPEquipped is set to 'true' and extends the tmnxPortOpticalCompliance field of the SFF.

OBJECT-TYPE

The value of tmnxPortEgrHsSchedPlcy specifies the egress QoS HS scheduler policy for this port. This object must correspond to the index of a row in TIMETRA-QOS-MIB::tHsSchedPolicyTable, otherwise an 'inconsistentValue' error will be returned. When the tmnxMDAAssignedType is a non-HS MDA type, the value for tmnxPortEgrHsSchedPlcy will be ignored. If the tmnxMDAAssignedType is a HS MDA type, the default for this object will be the string 'default'.

OBJECT-TYPE

The value of tmnxPortEgrHsPortPoolPlcy specifies the egress QoS HS port pool policy for this port. This object must correspond to the index of a row in TIMETRA-QOS-MIB::tHsPoolPolicyTable, otherwise an 'inconsistentValue' error will be returned. When the tmnxMDAAssignedType is a non-HS MDA type, the value for tmnxPortEgrHsPortPoolPlcy will be ignored. If the tmnxMDAAssignedType is a HS MDA type, the default for this object will be the string 'default'.

OBJECT-TYPE

The tmnxPortTestTable has an entry for each port on each IOM card in each chassis in the TMNX system.

OBJECT-TYPE

Each row entry represents a port on a IOM card in a chassis in the system. Entries cannot be created and deleted via SNMP SET operations.

OBJECT-TYPE

The current testing status of this port.

OBJECT-TYPE

The type of test to be executed on this port.

OBJECT-TYPE

A parameter to be passed to the test program.

OBJECT-TYPE

The status of the last test executed on this port.

OBJECT-TYPE

The date and time the test started on this port. Returns 0 if tmnxPortTestState is notInTest.

OBJECT-TYPE

The date and time the last test completed. Returns 0 if a test is in progress or no tests have yet to be run on this port.

OBJECT-TYPE

The number of seconds the port test is anticipated to last.

OBJECT-TYPE

The operator sets this variable to perform the appropriate type of testing.

OBJECT-TYPE

The tmnxPortEtherTable has an entry for each Ethernet (faste, gige, xcme or xgige) port on each IOM card in each chassis in the TMNX system.

OBJECT-TYPE

Each row entry represents an Ethernet port on a IOM card in a chassis in the system. Entries cannot be created and deleted via SNMP SET operations. Before an IOM card entry can be deleted from the tmnxMDATable, its supported tmnxPortEntry and tmnxPortEtherEntry rows must be in the proper state for removal. The tmnxPortEtherEntry contains attributes that are unique to the Ethernet TmnxPortType.

OBJECT-TYPE

The size of the largest packet which can be sent/received on the Ethernet physical interface, specified in octets. For interfaces that are used for transmitting network datagrams, this is the size of the largest network datagram that can be sent on the interface. Setting tmnxPortEtherMTU to a value of zero (0), causes the agent to recalculate the default MTU size which can vary based on the current setting of tmnxPortMode and tmnxPortEncapType variables. Some typical default values are: 1514 with mode access and encap type null 1518 with mode access and encap type dot1q 1518 with mode access and encap type mpls 9198 with mode network

OBJECT-TYPE

The tmnxPortEtherDuplex variable specifies the duplex mode used by the Ethernet interface if tmnxPortEtherAutoNegotiate has a value of 'false' or 'limited'. If tmnxPortEtherAutoNegotiate has a value of 'true', the link parameters are negotiated with the far end and the tmnxPortEtherDuplex variable is ignored. A value of 'fullDuplex' sets the link to full duplex mode. A value of 'halfDuplex' sets the link to half duplex mode. tmnxPortEtherDuplex is only valid on Ethernet interfaces that support multiple duplex modes.

OBJECT-TYPE

The tmnxPortEtherSpeed variable specifies the link speed of the Ethernet interface. tmnxPortEtherSpeed is only valid on Ethernet interfaces where tmnxPortClass is 'faste(2)' or 'xcme(8)' or 'vspeede(14)'. If tmnxPortEtherAutoNegotiate has a value of 'true(1)', the link parameters are negotiated with the far end and the tmnxPortEtherSpeed variable is ignored.

OBJECT-TYPE

When the value of tmnxPortEtherAutoNegotiate is 'true', the Ethernet interface will automatically negotiate link parameters with the far end (including speed and duplex), and will advertise all speeds and duplex modes supported by the interface. When the value of tmnxPortEtherAutoNegotiate is 'limited', the Ethernet interface will automatically negotiate link parameters with the far end, but will only advertise the speed and duplex mode specified by tmnxPortEtherSpeed and tmnxPortEtherDuplex. If tmnxPortEtherAutoNegotiate is 'false', the Ethernet interface will not negotiate link parameters with the far end and will instead force the speed and duplex mode to the values specified by tmnxPortEtherSpeed and tmnxPortEtherDuplex respectively.

OBJECT-TYPE

The tmnxPortEtherOperDuplex variable indicates the operational duplex mode of the Ethernet interface. A value of 'fullDuplex' indicates that the link is in full duplex mode. A value of 'halfDuplex' indicates that the link is in half duplex mode. tmnxPortEtherOperDuplex is only valid if tmnxPortClass is 'faste' or 'xcme'.

OBJECT-TYPE

The tmnxPortEtherOperSpeed variable indicates the operational speed of the Ethernet interface in megabits per second (mbps). If the value of tmnxPortEtherAutoNegotiate is 'true', the link autonegotiates the link parameters with the far end side. The value of tmnxPortEtherOperSpeed is only valid if tmnxPortClass is one of the Ethernet classes.

OBJECT-TYPE

The value of the accounting policy must be defined prior to associating the policy with the ethernet port. Accounting policies can only be associated with network ports. A non-zero value indicates the tmnxLogApPolicyId index identifying the policy entry in the tmnxLogApTable from the TIMETRA-LOG-MIB which is associated with this port. A zero value indicates that there is no accounting policy associated with this port

OBJECT-TYPE

Enable/disable the collection of accounting and statistical data for the network ethernet port. When applying accounting policies the data by default will be collected in the appropriate records and written to the designated billing file. When the value is set to false, the statistics are still accumulated by the IOM cards, however, the CPU will not obtain the results and write them to the billing file.

OBJECT-TYPE

The tmnxPortEtherMDIMDIX variable indicates whether the Ethernet interface is of type 'mdi' (Media Dependent Interface) or 'mdix' (Media Dependent Interface with crossover). If the agent cannot identify the type of Ethernet interface the value 'unknown (0)' is indicated. tmnxPortEtherMDIMDIX is only valid if tmnxPortClass is 'faste' or 'xcme'.

OBJECT-TYPE

The tmnxPortEtherXGigMode variable specifies whether the Ethernet interface is in LAN or WAN mode. tmnxPortEtherXGigMode must be 'notApplicable' if tmnxPortClass is not 'xgige'.

OBJECT-TYPE

The tmnxPortEtherEgressRate variable specifies the maximum egress bandwidth (in kilobits per second) that the Ethernet interface can generate. A value of -1 means that the limit is the actual physical limit. If the provisioned subrate bandwidth is larger than the actual physical bandwidth of the interface, the latter applies.

OBJECT-TYPE

The tmnxPortEtherDot1qEtype variable specifies the ethertype expected when the port's encapsulation type is dot1qEncap.

OBJECT-TYPE

The tmnxPortEtherQinqEtype variable specifies the ethertype expected when the port's encapsulation type is qinqEncap.

OBJECT-TYPE

The tmnxPortEtherIngressRate variable specifies the maximum ingress bandwidth (in megabits per second) that the Ethernet interface can receive. A value of -1 means that the limit is the actual physical limit. If the provisioned subrate bandwidth is larger than the actual physical bandwidth of the interface, the latter applies. For interfaces that support more than 10Gbps, the configured value must be specified as a multiple of 10Mbps; otherwise, the configuration will be rejected with an inconsistentValue error.

OBJECT-TYPE

The value of tmnxPortEtherReportAlarm determines when and if to generate tmnxEqPortEtherAlarm and tmnxEqPortEtherAlarmClear.

OBJECT-TYPE

The value of tmnxPortEtherReportAlarmStatus indicates the alarms on this port.

OBJECT-TYPE

The total number of packets received that were longer than 1518 octets but less than the maximum frame size for the particular medium, usually 12287 octets (excluding framing bits, but including FCS octets) and were otherwise well formed.

OBJECT-TYPE

The number of times the associated tmnxPortEtherPkts1519toMax counter has overflowed.

OBJECT-TYPE

The total number of packets (including bad packets) received that were between 1519 octets in length and the maximum frame size, usually 12287 octets inclusive (excluding framing bits but including FCS octets). The lower 32-bits of this 64-bit counter will equal the value of tmnxPortEtherHCPkts1519toMax. The high 32-bits of this counter will equal the value of tmnxPortEtherHCOverPkts1519toMax.

OBJECT-TYPE

The value of tmnxPortEtherLacpTunnel specifies whether the LACP packet tunneling for the ethernet port is enabled or disabled. When tunneling is enabled, the port will not process any LACP packets but will tunnel them through instead. Also, the port cannot be added as a member to a LAG group, and vice versa.

OBJECT-TYPE

The value of tmnxPortEtherDownWhenLoopedEnabled specifies whether physical loop detection for the Ethernet port is enabled or disabled. When enabled, the port will periodically send out keep-alive PDUs with an EtherType of 0x9000. If the port receives a keep-alive that it transmitted, tmnxPortState will be set to 'linkUp' if it was previously 'up'. The port will not move back to tmnxPortState 'up' for a period of time defined by tmnxPortEtherDownWhenLoopedRetry, but will continue to periodically send out keep-alive PDUs. Every time the port receives a keep alive it sent while a loop has been detected, it will reset the time period that it will remain down as defined by tmnxPortEtherDownWhenLoopedRetry.

OBJECT-TYPE

The tmnxPortEtherDownWhenLoopedKeepAlive variable specifies the number of seconds between each keep alive PDU transmission.

OBJECT-TYPE

The tmnxPortEtherDownWhenLoopedRetry variable specifies the minimum number of seconds the port should wait after detecting a loop before tmnxPortState can be set to 'up'. A value of 0 specifies the the port should not set tmnxPortState to 'up' until the user administratively disables and re-enables the port by setting tmnxPortAdminStatus to 'outOfService' and then to 'inService'.

OBJECT-TYPE

The value of tmnxPortEtherDownWhenLoopedState indicates whether a physical loop has been detected on the port or not. If tmnxPortEtherDownWhenLoopedEnabled is set to 'false', this value will be 'noLoopDetected'.

OBJECT-TYPE

The tmnxPortEtherPBBEtype variable specifies the Ethertype expected for Provider Backbone Bridging Frames.

OBJECT-TYPE

The tmnxPortEtherReasonDownFlags indicates why an ethernet port may be in the operationally 'down' state. The following reasons are detected through this object: unknown(0) - Unspecified (or unknown) linklossFwd(1) - A sap using this port has the object 'sapEthernetLLFOperStatus' set to 'fault' lagMemberPortStandby(2) - A lag using this port as a member port has set the member port to 'standby' while configured to keep standby member ports down.

OBJECT-TYPE

tmnxPortEtherSingleFiber is used to enable/disable packet gathering and redirection of IP packets from a single fiber on RX port of the Ethernet interface and redistribute packets to other interfaces through either state routes or policy-based forwarding.

OBJECT-TYPE

tmnxPortEtherSSM specifies whether or not synchronous status messages (SSM) are enabled on the ethernet port.

OBJECT-TYPE

tmnxPortEtherDWLUseBroadcastAddr specifies whether or not the Down When Looped destination MAC address is the broadcast address, 'true (1)', or the local port mac address, as specified in tmnxPortMacAddress, 'false (2)'.

OBJECT-TYPE

The value of tmnxPortEtherSSMCodeType specifies the code-type used by the Synchronous Status Message (SSM) channel.

OBJECT-TYPE

The value of tmnxPortEtherSSMTxDus specifies whether or not the value 0xF (dus/dnu) is forced in the Synchronous Status Message (SSM) channel.

OBJECT-TYPE

The value of tmnxPortEtherSSMRxEsmc indicates the SSM code received on the Ethernet Synchronization Messaging Channel of the Ethernet port. The value returned for this object is only meaningful if tmnxPortEtherSSM is 'true', and tmnxPortSSMRxQualityLevel is not 'failed'.

OBJECT-TYPE

The value of tmnxPortEtherSSMTxQualityLevel indicates the quality level transmitted in the Ethernet Synchronization Messaging Channel.

OBJECT-TYPE

The value of tmnxPortEtherCrcMonSdThreshold specifies a packet error rate threshold used to determine when to send a tmnxEqPortEtherCrcAlarm notification for a CRC Signal Degradation (SD) failure and tmnxEqPortEtherCrcAlarmClear notification for a CRC SD failure clear. tmnxPortEtherCrcMonSdThreshold is the absolute value of the exponent of the rate expressed as 10e-n. The CRC SD error rate threshold is calculated as: tmnxPortEtherCrcMonSdTMultiplier * 10e-tmnxPortEtherCrcMonSdThreshold. A value of 0 disables CRC SD monitoring.

OBJECT-TYPE

The value of tmnxPortEtherCrcMonSdTMultiplier specifies the tmnxPortEtherCrcMonSdThreshold multiplier value. The CRC SD error rate threshold is calculated as: tmnxPortEtherCrcMonSdTMultiplier * 10e-tmnxPortEtherCrcMonSdThreshold.

OBJECT-TYPE

The value of tmnxPortEtherCrcMonSfThreshold specifies a packet error rate threshold used to determine when to send a tmnxEqPortEtherCrcAlarm notification for a CRC Signal Failure (SF) failure. Crossing the tmnxPortEtherCrcMonSfThreshold will result in the tmnxPortOperStatus being set to 'outOfService'. tmnxPortEtherCrcMonSfThreshold is the absolute value of the exponent of the rate expressed as 10e-n. The CRC SF error rate threshold is calculated as: tmnxPortEtherCrcMonSfTMultiplier * 10e-tmnxPortEtherCrcMonSfThreshold. A value of 0 disables CRC SF monitoring.

OBJECT-TYPE

The value of tmnxPortEtherCrcMonSfTMultiplier specifies the tmnxPortEtherCrcMonSfThreshold multiplier value. The CRC SF error rate threshold is calculated as: tmnxPortEtherCrcMonSfTMultiplier * 10e-tmnxPortEtherCrcMonSfThreshold.

OBJECT-TYPE

The value of tmnxPortEtherCrcMonWindowSize specifies the size of the sliding window in seconds over which the tmnxPortEtherCrcMonSdThreshold and tmnxPortEtherCrcMonSfThreshold are applied.

OBJECT-TYPE

The value of tmnxPortEtherCrcAlarmReason indicates the current status of the Ethernet CRC Monitored alarms on the port.

OBJECT-TYPE

The value of tmnxPortEtherDownOnInternalError specifies whether or not the port is monitored for excessive internal MAC tx errors. When enabled, excess Internal MAC tx errors results in the tmnxPortOperStatus being set to 'outOfService (3)' and a tmnxEqPortEtherInternalAlarm notification trap.

OBJECT-TYPE

The value of tmnxPortEtherMinFrameLength specifies the minimum length of any frame transmitted out of the port.

OBJECT-TYPE

The value of tmnxPortEtherPhysAcctPolicyId specifies the TIMETRA-LOG-MIB::tmnxLogApPolicyId that identifies the policy entry in TIMETRA-LOG-MIB::tmnxLogApTable which is associated with this ethernet port for the purpose of collecting physical layer ethernet statistics. A zero value indicates that there is no accounting policy associated with this ethernet port.

OBJECT-TYPE

The value of tmnxPortEtherPhysCollectStats specifies whether or not the collection of physical layer ethernet accounting and statistical data for the ethernet port is enabled. When a non-zero value is specified for tmnxPortEtherPhysAcctPolicyId and tmnxPortEtherPhysCollectStats is set to true, data will be collected in the appropriate records and written to the designated billing file. When a non-zero value is specified for tmnxPortEtherPhysAcctPolicyId and tmnxPortEtherPhysCollectStats is set to false, the statistics are still accumulated by the IOM cards; however, the CPM will not obtain the results and write them to the billing file.

OBJECT-TYPE

The value of tmnxPortEtherOperPhyTxClock indicates the result of Master/Slave resolution on copper based Ethernet ports. tmnxPortEtherOperPhyTxClock is 'notApplicable' if tmnxPortClass is not 'xcme' and tmnxPortType is not 'portTypeXcmeTx' and 'tmnxPortEtherOperSpeed' is not 1000.

OBJECT-TYPE

The value of tmnxPortEtherDwnOnIntlErrTxDisbl specifies whether or not a signal is sent to the remote transmitter to disable the laser before the port is brought out of service from excessive internal MAC tx errors. The value of this object is only valid when the value of tmnxPortEtherDownOnInternalError is 'true (1)', and the port is not fixed or pluggable copper.

OBJECT-TYPE

The value of tmnxPortEtherAccessBandwidth specifies the administrative bandwidth assigned to this port. The administrative bandwidth can be over or under booked using the value of tmnxPortEtherAccessBookingFactor.

OBJECT-TYPE

The value of tmnxPortEtherAccessBookingFactor specifies the booking factor, against the administrative bandwidth specified by tmnxPortEtherAccessBandwidth.

OBJECT-TYPE

The value of tmnxPortEtherAccessAvailableBW indicates the bandwidth that is still free for booking on this port.

OBJECT-TYPE

The value of tmnxPortEtherAccessBookedBW indicates the port bandwidth that has been booked.

OBJECT-TYPE

The value of tmnxPortEtherPTPAsymmetry specifies the path asymmetry correction value (in nanoseconds) that is used to specify the difference in transmission time between master-to-slave and slave-to-master. The user should compute the value using the following formula. Ingress and Egress are from the slave's point of view. asymmetry = (ingress propagation time - egress propagation time)/2.

OBJECT-TYPE

The value of tmnxPortEtherUtilStatsInterval specifies the time interval used to calculate the port utilization statistics.

OBJECT-TYPE

The value of tmnxPortEtherUtilStatsInput indicates the utilization of the port in relation to the data received and the port capacity. This utilization is measured over the interval indicated by tmnxPortEtherUtilStatsInterval.

OBJECT-TYPE

The value of tmnxPortEtherUtilStatsOutput indicates the utilization of the port in relation to the data transmitted and the port capacity. This utilization is measured over the interval indicated by tmnxPortEtherUtilStatsInterval.

OBJECT-TYPE

The value of tmnxPortEtherRsFecMode specifies the mode of Reed-Solomon Forward Error Correction (RS-FEC) to be used by this ethernet port. When the value of tmnxPortEtherRsFecMode is set to 'none', the port will transmit and receive using standard 64B/66B encoding.

OBJECT-TYPE

The value of tmnxPortEtherEthBnEgrRateChanges specifies whether or not the changes received in Eth-BN messages on a port based MEP are allowed to update the egress rate used on the port. The value 'true (1)' specifies that the egress rate on the port is allowed to be updated.

OBJECT-TYPE

The value of tmnxPortEtherEthBnEgressRate indicates the ETH-BN (Ethernet Bandwidth Notification) egress rate received from the ETH-CFM (Ethernet Connectivity Fault Management) subsystem. A value of '-1' indicates that the rate value is not available.

OBJECT-TYPE

The value of tmnxPortEtherOperEgressRate indicates the operational egress bandwidth (in kilobits per second) that the Ethernet interface can generate. The value is the minimum of the admin egress rate tmnxPortEtherEgressRate, the ETH-BN egress rate tmnxPortEtherEthBnEgressRate, and the port's maximum rate. A value of '-1' means that the limit is the actual physical limit.

OBJECT-TYPE

The tmnxPortEtherAccessBandwidthHi specifies the high 32-bit value of administrative bandwidth assigned to this port. Lower 32-bit value of administrative bandwidth is assigned using tmnxPortEtherAccessBandwidth. An 'inconsistentValue' error is returned when value of this object is changed to non-default and tmnxPortEtherAccessBandwidth is not set in the same request. The administrative bandwidth can be over or under booked using the value of tmnxPortEtherAccessBookingFactor.

OBJECT-TYPE

The value of tmnxPortEtherEgrQosPortQosPlcy specifies the name to associate with this port.

OBJECT-TYPE

The value of tmnxPortEtherLoopback specifies the loopback mode of the port. none(0) - Loopback is disabled. line(1) - Loopback loops frames received on this port back to the remote system. internal(2) - Loopback loops frames from the local system back at the framer.

OBJECT-TYPE

The value of tmnxPortEtherLoopbackSwapMac specifies if the source and destination MAC addresses in the packets are to be interchanged before being loopbacked to the sender. Setting tmnxPortEtherLoopbackSwapMac must be accompanied by setting tmnxPortEtherLoopback for the same port.

OBJECT-TYPE

The value of tmnxPortEtherAccessAcctPolicyId specifies the TIMETRA-LOG-MIB::tmnxLogApPolicyId that identifies the policy entry in TIMETRA-LOG-MIB::tmnxLogApTable which is associated with this ethernet access port queue for the purpose of collecting physical layer ethernet access port queue statistics. A zero value indicates that there is no accounting policy associated with this ethernet access port.

OBJECT-TYPE

The value of tmnxPortEtherAccessCollectStats specifies whether or not the collection of physical layer ethernet accounting and statistical data for the ethernet access port queue is enabled. When a non-zero value is specified for tmnxPortEtherAccessAcctPolicyId and tmnxPortEtherAccessCollectStats is set to true, data will be collected in the appropriate records and written to the designated billing file. When a non-zero value is specified for tmnxPortEtherAccessAcctPolicyId and tmnxPortEtherAccessCollectStats is set to false, the statistics are still accumulated by the IOM cards; however, the CPM will not obtain the results and write them to the billing file.

OBJECT-TYPE

The tmnxSonetTable has an entry for each packet over Sonet port on each IOM card in each chassis in the TMNX system.

OBJECT-TYPE

Each row entry represents a packet over Sonet port on a IOM card in a chassis in the system. Entries cannot be created and deleted via SNMP SET operations. Before an IOM tmnxMDAEntry can be deleted from the tmnxMDATable, its supported tmnxPortEntry rows must be in the proper state for removal. The tmnxSonetEntry contains attributes that are unique to the 'sonet' TmnxPortType. It also contains attributes that are common to all sonet paths configured on a sonet port. The tmnxPortPortID for a sonet port includes a sonet path number in the lower bits. If the sonet path number is zero, '0', it represents a single (clear) sonet path on the port that uses the full bandwidth of the sonet port. All entries in this table have the sonet path number part of their tmnxPortPortID index value set to zero.

OBJECT-TYPE

The rate of this optical facility.

OBJECT-TYPE

tmnxSonetClockSource configures the clock for transmitted data from either the internal clock ('nodeTimed') or from a clock recovered from the line's receive data stream ('loopTimed').

OBJECT-TYPE

The value of tmnxSonetFraming specifies the type of framing used on this interface.

OBJECT-TYPE

The value of tmnxSonetReportAlarm determines when and if to generate tmnxEqPortSonetAlarm and tmnxEqPortSonetAlarmClear notifications for this port: loc(1) Reports a loss of clock which causes the operational state of the port to be downed. Set by default. lais(2) Reports line alarm indication signal errors. Not set by default. lrdi(3) Reports line remote defect initiation errors. LRDIs are caused by remote LOF, LOC, and LOS. Set by default. ss1f(4) Reports section synchronization failure as reported by the S1 byte. Not set by default. sb1err(5) Reports section B1 errors. Not set by default. lb2erSd(6) Reports line signal degradation BER errors. Not set by default. lb2erSf(7) Reports line signal failure BER errors. Set by default. slof(8) Reports section loss of frame errors. Set by default slos(9) Reports section loss of signal errors. Set by default. stxptr(10) Reports a section synchronization error on the transmit side. Indicates if there is a positive or negative justification count per channel. Not set by default. srxptr(11) Reports a section synchronization error on the receive side. Indicates if there is a positive or negative justification count per path. Not set by default. lrei(12) Reports a line error condition raised by the remote as a result of B1 errors received from this node. Not set by default.

OBJECT-TYPE

The value of tmnxSonetBerSdThreshold specifies a bit error rate (BER) threshold used to determine when to send a tmnxEqPortSonetAlarm notification for a BER SD failure and tmnxEqPortSonetAlarmClear notification for a BER SD failure clear. tmnxSonetBerSdThreshold is the absolute value of the exponent of the rate expressed as 10e-n.

OBJECT-TYPE

The value of tmnxSonetBerSfThreshold specifies a bit error rate (BER) threshold used to determine when to send a tmnxEqPortSonetAlarm notification for a BER SF failure and tmnxEqPortSonetAlarmClear notification for a BER SF failure clear. tmnxSonetBerSdThreshold is the absolute value of the exponent of the rate expressed as 10e-n.

OBJECT-TYPE

Automatic Protection Switching (APS) is supported on 7x50 systems by the APS-MIB and TIMETRA-APS-MIB.

OBJECT-TYPE

Automatic Protection Switching (APS) is supported on 7x50 systems by the APS-MIB and TIMETRA-APS-MIB.

OBJECT-TYPE

Automatic Protection Switching (APS) is supported on 7x50 systems by the APS-MIB and TIMETRA-APS-MIB.

OBJECT-TYPE

Automatic Protection Switching (APS) is supported on 7x50 systems by the APS-MIB and TIMETRA-APS-MIB.

OBJECT-TYPE

Automatic Protection Switching (APS) is supported on 7x50 systems by the APS-MIB and TIMETRA-APS-MIB.

OBJECT-TYPE

Automatic Protection Switching (APS) is supported on 7x50 systems by the APS-MIB and TIMETRA-APS-MIB.

OBJECT-TYPE

Automatic Protection Switching (APS) is supported on 7x50 systems by the APS-MIB and TIMETRA-APS-MIB.

OBJECT-TYPE

Automatic Protection Switching (APS) is supported on 7x50 systems by the APS-MIB and TIMETRA-APS-MIB.

OBJECT-TYPE

Automatic Protection Switching (APS) is supported on 7x50 systems by the APS-MIB and TIMETRA-APS-MIB.

OBJECT-TYPE

Activate a loopback on the SONET port. The SONET port must be in a shutdown state to activate any type of loopback.

OBJECT-TYPE

The bits in this object are used for indicating the alarms. The bits are explained as follows: loc(1) Indicates a loss of clock which causes the operational state of the port to be downed. lais(2) Indicates line alarm indication signal errors. lrdi(3) Indicates line remote defect indication errors. LRDIs are caused by remote LOF, LOC, and LOS. ss1f(4) Indicates section synchronization failure as reported by the S1 byte. sb1err(5) Indicates section B1 errors. lb2erSd(6) Indicates line signal degradation BER errors. lb2erSf(7) Indicates line signal failure BER errors. slof(8) Indicates section loss of frame errors. slos(9) Indicates section loss of signal errors. stxptr(10) Indicates a section synchronization error on the transmit side. Indicates if there is a positive or negative justification count per channel. srxptr(11) Indicates a section synchronization error on the receive side. Indicates if there is a positive or negative justification count per sonet path. lrei(12) Indicates a line error condition raised by the remote as a result of B1 errors received from this node.

OBJECT-TYPE

The tmnxSonetSectionTraceMode variable along with the tmnxSonetJ0String object determines the contents of the section trace bytes (j0/z0) in the SONET Section Header. If the mode is set to 'increment-z0', then the j0 byte is 0x01, and the z0 byte increments. If the mode is set to 'byte', then the j0 byte is the first octet of the tmnxSonetJ0String object and the z0 byte is 0xcc. If the mode is set to 'string', then the J0 byte is set to the 16 values in the tmnxSonetJ0String object and the z0 byte is 0xcc.

OBJECT-TYPE

The tmnxSonetJ0String is used with the tmnxSonetSectionTraceMode variable to determine the contents of the j0 byte in the SONET Section Header. If the tmnxSonetSectionTraceMode is increment-z0, this object is ignored. If the mode is byte, then the first octet of this object is used for the J0 byte. The default J0 byte is 0. If the mode is string, then the 16 bytes in this object are used for the J0 byte. If set to less than 16 bytes it, will be padded out to 16 with zeros. The default value is 'Alcatel' appended with platform and product name (example: `Alcatel 7x50 SR` )

OBJECT-TYPE

The tmnxSonetMonS1Byte variable reports the Synchronization Status Message from the S1 byte in the Line Overhead Header. A value of 0x00 indicates unknown quality. A value of 0xF0 indicates `Do not use for synchronization`. Other values are documented in Telcordia GR253 and ITU G.707

OBJECT-TYPE

The tmnxSonetMonJ0String variable reports the contents of the j0 byte in the SONET Section Header.

OBJECT-TYPE

The tmnxSonetMonK1Byte variable reports the Automatic Protection Switching(APS) signalling status from the K1 byte in the SONET Line Overhead Header.

OBJECT-TYPE

The tmnxSonetMonK1Byte variable reports the Automatic Protection Switching(APS) signalling status from the K2 byte in the SONET Line Overhead Header.

OBJECT-TYPE

tmnxSonetSingleFiber is used to enable/disable packet gathering and redirection of IP packets from a single fiber on RX port of the SONET interface and redistribute packets to other interfaces through either state routes or policy-based forwarding.

OBJECT-TYPE

The value of tmnxSonetHoldTimeUp is used to configure the hold-timer for link up event dampening. A value of zero (0) indicates that an up transition is reported immediately.

OBJECT-TYPE

The value of tmnxSonetHoldTimeDown is used to configure the hold-timer for link down event dampening. A value of zero (0) indicates that a down transition is reported immediately.

OBJECT-TYPE

The value of tmnxSonetSuppressLoOrderAlarm specifies whether or not the lower order alarms on Sonet ports are suppressed.

OBJECT-TYPE

The value of tmnxSonetTxDus specifies whether or not the value 0xF (dus/dnu) is forced in the S1 overhead byte.

OBJECT-TYPE

The value of tmnxSonetTxS1Byte indicates the transmitted S1 Byte.

OBJECT-TYPE

The value of tmnxSonetResetPortOnPathDown specifies whether or not the port will be reset when the path transitions to the oper down state.

OBJECT-TYPE

The tmnxSonetPathTable has an entry for each sonet path configured in each packet over Sonet port on each IOM card in each chassis in the TMNX system.

OBJECT-TYPE

Each row entry represents a configured sonet path in a packet over Sonet port on a IOM card in a chassis in the system. The tmnxSonetPathEntry contains attributes that are unique to a sonet path of a 'sonet' TmnxPortType. The tmnxPortPortID for a sonet port includes a sonet path number in the lower bits. If the sonet path number is zero, '0', it represents a single (clear) sonet path on the port that uses the full bandwidth of the sonet port. Entries in this table that have the sonet path number part of their tmnxPortPortID index value set to zero cannot be created and deleted via SNMP SET operations. They are created by the SNMP agent when the corresponding entry in the tmnxSonetTable is created. Entries with non-zero sonet path numbers can be created and deleted via SNMP SET operations using tmnxSonetPathRowStatus. When a row is created in the tmnxSonetPathTable, the agent also creates a row with the same index values in the tmnxPortTable. In order to delete an entry, tmnxPortAdminStatus must first be set to 'outOfService'. When the tmnxSonetPathEntry is deleted, the agent also deletes the corresponding row in the tmnxPortTable.

OBJECT-TYPE

tmnxSonetPathRowStatus controls the creation and deletion of row entries in the tmnxSonetPathTable. The tmnxPortPortID for a sonet port includes a sonet path number in the lower bits. If the sonet path number is zero, '0', it represents a single (clear) sonet path on the port that uses the full bandwidth of the sonet port. Entries in this table that have the sonet path number part of their tmnxPortPortID index value set to zero cannot be created and deleted via SNMP SET operations. They are created by the SNMP agent when the corresponding entry in the tmnxSonetTable is created. Entries with non-zero sonet path numbers can be created and deleted via SNMP SET operations. When a row is created in the tmnxSonetPathTable, the agent also creates a row with the same index values in the tmnxPortTable. In order to delete an entry, tmnxPortAdminStatus must first be set to 'outOfService'. When the tmnxSonetPathEntry is deleted, the agent also deletes the corresponding row in the tmnxPortTable for this sonet path port.

OBJECT-TYPE

The tmnxSonetPathLastChangeTime variable contains the sysUpTime value of the most recently modified writable variable in the tmnxSonetPathEntry row for this sonet path.

OBJECT-TYPE

The size of the largest packet which can be sent/received on the sonet path, specified in octets. For paths that are used for transmitting network datagrams, this is the size of the largest network datagram that can be sent on the sonet path. Setting tmnxSonetPathMTU to a value of zero (0), causes the agent to recalculate the default MTU size which can vary based on the current setting of tmnxPortMode and tmnxPortEncapType variables. Some typical default values are: 1522 with mode access and encap type bcp-null 1526 with mode access and encap type bcp-dot1q 1502 with mode access and encap type ipcp 1506 with mode access and encap type mplscp 1524 with mode access and encap type atm 9208 with mode network

OBJECT-TYPE

If the tmnxSonetPathScramble variable is set to 'true', SONET (SDH) payload scrambling is enabled on this sonet path. Both ends of the connection must use the same scrambling algorithm. If tmnxSonetPathScramble is set to 'false', scrambling is disabled. The default value for non-ATM paths is 'false'. The default value for ATM paths is 'true' If the value of tmnxSonetPathC2Byte is set to the default for the currently configured tmnxSonetPathScramble, then changing the value of tmnxSonetPathScramble for non-ATM paths causes a change to tmnxSonetPathC2Byte to a default value for a new scrambling option. The default values are as follows: scrambled non-ATM sonet/sdh path - C2 Byte value is 0x16 unscrambled non-ATM sonet/sdh path - C2 Byte value is 0xCF

OBJECT-TYPE

The tmnxSonetPathC2Byte variable is used configure the value used in the SONET/SDH C2 header byte. For paths on an MDA that does not support channelization: Setting C2 equal to 0x16 indicates scrambled sonet. Setting C2 equal to 0xCF indicates unscrambled sonet. Setting C2 equal to 0x13 indicates ATM. For paths on an MDA that supports channelization, the default value is based on the value of tmnxMDAMaxChannelization. For 'pdhDs3' or 'pdhE3' channelization, the default value is 0x04. Setting tmnxSonetPathC2Byte to a value of zero(0) causes the agent to assign the default value to this object.

OBJECT-TYPE

The tmnxSonetPathJ1String variable is used to configure the sonet path trace string to be sent in the J1 Path Overhead bytes. The bytes must be printable ASCII. If the string is less than 62 bytes, it will be padded with NULLs. For SONET framing, an additional CR (0x0D) / LF (0x0A) pair will be added by the driver. For SDH framing only 16 bytes are sent in the J1 bytes. The driver will set the MSB of the first byte, and put the first 15 bytes of the user configured string as the following bytes. The driver will set the CRC-7 of the 16 bytes into the other 7 bits of the first byte. The default value is `Alcatel 7x50 SR`. Setting a 1-byte long string containing 0xFF will restore the default. Setting the string 'zeros' will send all-zeros (ASCII NULL characters without CR/LF or CRC-7) in the J1 bytes.

OBJECT-TYPE

The value of tmnxSonetPathCRC variable specifies the precision of the cyclic redundancy check. A value of 'crc16' is a 16-bit CRC calculation. A value of 'crc32' is a 32-bit CRC calculation. 32-bit CRC increases the error detection ability, but it also adds some performance overhead. For paths with encapsulation set to ATM the default and only supported value is crc32 and applies to AAL5 CRC calculations on that path.

OBJECT-TYPE

The negotiated size of the largest packet which can be sent on the sonet path, specified in octets. For sonet paths that are used for transmitting network datagrams, this is the size of the largest network datagram that can be sent on the sonet path.

OBJECT-TYPE

The negotiated size of the largest packet that can be received on the sonet path, specified in octets.

OBJECT-TYPE

The value of tmnxSonetPathReportAlarm determines when and if to generate tmnxEqPortSonetPathAlarm and tmnxEqPortSonetPathAlarmClear notifications for this port: pais(1) Reports path alarm indication signal errors. Not set by default. plop(2) Reports path loss of pointer (per tributary) errors. Set by default. prdi(3) Reports path remote defect indication errors. Not set by default. pb3err(4) Reports path B3 errors. Not set by default. pplm(5) Reports a path payload mismatch. As a result the path will be operationally downed. Set by default. prei(6) Reports a path error condition raised by the remote as a result of B3 errors received from this node. Not set by default. puneq(7) Reports unequipped path errors. Set by default. plcd(8) Reports path loss of codegroup delineation error. It is applicable only when the value of tmnxPortEtherXGigMode is set to 'wan'. Not set by default.

OBJECT-TYPE

The value of the accounting policy must be defined prior to associating the policy with the sonet path. Accounting policies can only be associated with network sonet path. A non-zero value indicates the tmnxLogApPolicyId index identifying the policy entry in the tmnxLogApTable from the TIMETRA-LOG-MIB which is associated with this port. A zero value indicates that there is no accounting policy associated with this port

OBJECT-TYPE

Enable/disable the collection of accounting and statistical data for the network sonet path. When applying accounting policies the data by default will be collected in the appropriate records and written to the designated billing file. When the value is set to false, the statistics are still accumulated by the IOM cards, however, the CPU will not obtain the results and write them to the billing file.

OBJECT-TYPE

The bits in this object are used for indicating the alarms. The bits are explained as follows: pais(1) Indicates path alarm indication signal errors. plop(2) Indicates path loss of pointer (per tributary) errors. prdi(3) Indicates path remote defect indication errors. pb3err(4) Indicates path B3 errors. pplm(5) Indicates a path payload mismatch. prei(6) Indicates a path error condition raised by the remote as a result of B3 errors received from this node. puneq(7) Indicates a far-end unequipped error. plcd(8) Indicates a path loss of codegroup delineation error. It is applicable only when the value of tmnxPortEtherXGigMode is set to 'wan'. Not set by default.

OBJECT-TYPE

The tmnxSonetPathC2Byte variable reports the value in the SONET/SDH C2 header byte.

OBJECT-TYPE

The tmnxSonetPathJ1String variable reports the sonet path trace string received in the J1 Path Overhead bytes.

OBJECT-TYPE

tmnxSonetPathType specifies if the associated SONET/SDH Path is an asynchronous circuit, a virtual tributary group or a tributary unit group. ds3 - Configures the port or channel as service access(ds3) e3 - Configures the port or channel as service access(e3) vtg - Configures the path as a virtual tributary group. tug-2 - Configures the path as a tributary unit group. tug-3 - Configures the port or channel for transport network use.

OBJECT-TYPE

tmnxSonetPathChildType is used to configure the type of this path. Some typical default values are: pdhDs3 for STS-1 paths pdhE3 for TU3 paths pdhE1 for VT2 paths pdhDs1 for VT15 paths Examples of valid child path types are sonetSts3, sdhTug3, pdhDs3, pdhE3, sonetVt15, sonetVt2, pdhDs1 and pdhE1.

OBJECT-TYPE

The Port type table has an entry for each SR OS port type. Some example port types are: '100Mb Ethernet FX', '100Mb Ethernet FX', 'OC-768 SONET/SDH', 'DS3/E3'.

OBJECT-TYPE

Each row entry represents an Nokia SROS series port model. Rows in this table are created by the agent at initialization and cannot be created or destroyed by SNMP Get or Set requests.

OBJECT-TYPE

The unique index value which identifies this type of Nokia SROS series port model.

OBJECT-TYPE

The administrative name that identifies this type of Nokia SROS series port model. This name string may be used in CLI commands to specify a particular Port model type.

OBJECT-TYPE

A detailed description of this Nokia SROS series port model.

OBJECT-TYPE

When tmnxPortTypeStatus has a value of 'true' it indicates that this port model is supported in this revision of the management software. When it has a value of 'false' there is no support.

OBJECT-TYPE

The Port Connector type table has an entry for each port connector type. Some example port connector types are: 'Small Form Factor Plugin (SFP)', 'SC Simplex'.

OBJECT-TYPE

Each row entry represents an Nokia SROS series port Connector model. Rows in this table are created by the agent at initialization and cannot be created or destroyed by SNMP Get or Set requests.

OBJECT-TYPE

The unique index value which identifies this type of Nokia SROS series port connector model.

OBJECT-TYPE

The administrative name that identifies this type of Nokia SROS series port connector model. This name string may be used in CLI commands to specify a particular port connector model type.

OBJECT-TYPE

A detailed description of this Nokia SROS series port connector model.

OBJECT-TYPE

When tmnxPortConnectTypeStatus has a value of 'true' it indicates that this port connector model is supported in this revision of the chassis management software. When it has a value of 'false' there is no support.

OBJECT-TYPE

The Network Port FC Stats table has an entry for each forwarding class defined on each network port.

OBJECT-TYPE

Each row entry represents a set of ingress and egress packet and octet statistics for the given network port and forwarding class. Rows in this table are created by the agent when the network port is provisioned and cannot be created or destroyed by SNMP Get or Set requests.

OBJECT-TYPE

The forwarding class associated with these stats on this network port.

OBJECT-TYPE

The number of in-profile packets (rate below CIR) forwarded by the ingress Qchip.

OBJECT-TYPE

The number of out-of-profile packets (rate above CIR) forwarded by the ingress Qchip.

OBJECT-TYPE

The number of in-profile octets (rate below CIR) forwarded by the ingress Qchip.

OBJECT-TYPE

The number of out-of-profile octets (rate above CIR) forwarded by the ingress Qchip.

OBJECT-TYPE

The number of in-profile packets (rate below CIR) dropped by the ingress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The number of out-of-profile packets (rate above CIR) dropped by the ingress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The number of in-profile octets (rate below CIR) dropped by the ingress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The number of out-of-profile octets (rate above CIR) dropped by the ingress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The number of in-profile packets (rate below CIR) forwarded by the egress Qchip.

OBJECT-TYPE

The number of out-of-profile packets (rate above CIR) forwarded by the egress Qchip.

OBJECT-TYPE

The number of in-profile octets (rate below CIR) forwarded by the egress Qchip.

OBJECT-TYPE

The number of out-of-profile octets (rate above CIR) forwarded by the egress Qchip.

OBJECT-TYPE

The number of in-profile packets (rate below CIR) dropped by the egress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The number of out-of-profile packets (rate above CIR) dropped by the egress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The number of in-profile octets (rate below CIR) dropped by the egress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The number of out-of-profile octets (rate above CIR) dropped by the egress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The tmnxDS3Table has an entry for a DS3 physical port.

OBJECT-TYPE

Each row entry represents a physical DS3 port on a IOM card in a chassis in the system. Entries cannot be created and deleted via SNMP SET operations. Entries in this table will be created automatically when the tmnxMDAAssignedType object is set to the DS3 MDA type The tmnxDS3Entry contains attributes that are unique to the 'ds3e3' TmnxPortType. The tmnxPortPortID contains the slot, mda and port numbers encoded into it. For each tmnxDS3Entry, there will be a corresponding entry in the tmnxPortTable and the ifTable.

OBJECT-TYPE

tmnxDS3Buildout configures the T3 line buildout. A T3 port has two settings for the T3 line buildout: a short setting, which is less than 225 feet, and a long setting, which is greater than 225 feet. This object applies to copper-cable-based T3 ports only.

OBJECT-TYPE

The tmnxDS3LastChangeTime variable contains the sysUpTime value of the most recently modified writable variable in the tmnxDS3Entry row for this port.

OBJECT-TYPE

tmnxDS3Type configures the type of the physical port to 'ds3' or 'e3'.

OBJECT-TYPE

The value of tmnxDS3HoldTimeUp is used to configure the hold-timer for link up event dampening. A value of zero (0) indicates that an up transition is reported immediately.

OBJECT-TYPE

The value of tmnxDS3HoldTimeDown is used to configure the hold-timer for link down event dampening. A value of zero (0) indicates that a down transition is reported immediately.

OBJECT-TYPE

The tmnxDS3ChannelTable has an entry for a DS3 channel.

OBJECT-TYPE

Each row entry represents a DS3 channel. Entries can be created and deleted via SNMP SET operations. The tmnxDS3ChannelEntry contains attributes that are applicable to a DS3 channel which can belong to the DS3 physical port or belong to a container on a sonet path. The tmnxPortPortID contains the slot, mda and port numbers encoded into it. For each tmnxDS3ChannelEntry, there will be a corresponding entry in the tmnxPortTable and the ifTable.

OBJECT-TYPE

tmnxDS3ChannelRowStatus controls the creation and deletion of row entries in the tmnxDS3ChannelTable. For row creation, the manager has to first calculate the tmnxPortPortID based on the TiMOS encoding scheme.

OBJECT-TYPE

The value of tmnxDS3ChannelType indicates whether the channel is in DS3 or E3 mode.

OBJECT-TYPE

The value of tmnxDS3ChannelFraming specifies the type of framing associated with the DS3 channel. If tmnxDS3ChannelType is set to 'ds3', the default framing is 'cbit'. If tmnxDS3ChannelType is set to 'e3', the default framing is 'g751'.

OBJECT-TYPE

tmnxDS3ChannelClockSource configures the clock for transmitted data from either the internal clock ('nodeTimed'), or from a clock recovered from the line's receive data stream ('loopTimed').

OBJECT-TYPE

tmnxDS3ChannelChannelized is used to create subchannels of type 'ds1' or 'e1' or 'j1' on the interface. Setting the value to 'none' removes the subchannels on the interface.

OBJECT-TYPE

tmnxDS3ChannelSubrateCSUMode configures the channel service unit (CSU) compatibility mode to interoperate with existing DS3 subrate standards. This configuration applies only for a non-channelized DS3. Changing the value of tmnxDS3ChannelSubrateCSUMode to notUsed resets the value of tmnxDS3ChannelScramble to 'false'. Changing the value of tmnxDS3ChannelSubrateCSUMode resets the value of tmnxDS3ChannelSubrate to default for the mode if tmnxDS3ChannelSubrate is not provided.

OBJECT-TYPE

tmnxDS3ChannelSubrate configures the subrate step. tmnxDS3ChannelSubrate multiplied by the granularity for a particular mode as defined by tmnxDS3ChannelSubrateCSUMode gives the absolute subrate in kbps. ----------------------------------------------------------------------- Subrate CSU Mode|Granularity|Default|Range |Subrate speed range ----------------------------------------------------------------------- notUsed | N/A | 0 | 0 |N/A digital-link | 301 kbps | 1 | 1 to 147 |301 kbps to 44.2 mbps larscom | 3158 kbps | 1 | 1 to 14 |3158 kbps to 44.2 mbps ----------------------------------------------------------------------

OBJECT-TYPE

tmnxDS3ChannelIdleCycleFlags configures the value that the DS3 port transmits during idle cycle. The default value applies to HDLC channels only. For ATM channels the object does not really apply so a default value of 'none' is used and cannot be changed.

OBJECT-TYPE

tmnxDS3ChannelLoopback is used to put the channel into a loopback mode. The value of tmnxPortAdminStatus should be set to 'outOfService' in order for the loopback to be enabled. A 'line' loopback loops frames received on this port back to the remote system. A 'internal' loopback loops the frames from the local system back at the framer. When the value is set to 'remote', a signal is sent to the remote system to provide a line loopback.

OBJECT-TYPE

tmnxDS3ChannelBitErrorInsertionRate is used to insert bit errors for a BERT test. The number of error corresponds to 10^(-rate). A rate of 7 will cause an error rate of 10^(-7), or 1 error in every 10 million bits transmitted. If the value is set to 0, it disables the insertion of bit errors into the BERT. Change in this value while the test is running is accepted but does not take effect until the test gets restarted.

OBJECT-TYPE

tmnxDS3ChannelBERTPattern specifies the pattern used for the Bit Error Rate Test (BERT). The value of tmnxDS3ChannelBERTDuration indicates the duration of the test. Setting the value of this object to 'none' terminates the test.

OBJECT-TYPE

tmnxDS3ChannelBERTDuration is used to set the duration of the BERT test.

OBJECT-TYPE

tmnxDS3ChannelMDLEicString configures the Equipment ID Code(EIC) of the Message Data Link (MDL).

OBJECT-TYPE

tmnxDS3ChannelMDLLicString configures the Location ID Code(LIC) of the Message Data Link (MDL).

OBJECT-TYPE

tmnxDS3ChannelMDLFicString configures the Frame ID Code(FIC) of the Message Data Link (MDL).

OBJECT-TYPE

tmnxDS3ChannelMDLUnitString configures the Unit ID Code(UIC) of the Message Data Link (MDL).

OBJECT-TYPE

tmnxDS3ChannelMDLPfiString configures the Facility ID Code sent in the Message Data Link (MDL) Path message.

OBJECT-TYPE

tmnxDS3ChannelMDLPortString configures the port number string sent in the Message Data Link (MDL) idle signal message.

OBJECT-TYPE

tmnxDS3ChannelMDLGenString configures the generator number string sent in the Message Data Link (MDL) test signal message.

OBJECT-TYPE

tmnxDS3ChannelMDLMessageType configures the type of MDL message that is transmitted over the DS3 interface. If the value of this object is set to 'none', MDL messages are not transmitted. ds3Path(0) - Enables transmission of the MDL path message. An MDL path message, as defined by ANSI T1.107, is distinguished from idle and test signal messages in that it contains a facility identification code as its final data element. idleSignal(1) - Enables transmission of the MDL idle signal message. An MDL idle signal message, as defined by ANSI T1.107, is distinguished from path and test signal messages in that it contains a port number as its final data element. testSignal(2) - Enables transmission of the MDL test signal message. An MDL test signal message, as defined by ANSI T1.107, is distinguished from path and idle signal messages in that it contains a generator number as its final data element.

OBJECT-TYPE

When tmnxDS3ChannelFEACLoopRespond has a value of 'true', the channel is enabled to respond to remote loop signals. When it has a value of 'false' the port will not respond.

OBJECT-TYPE

The value of tmnxDS3ChannelCRC variable specifies the precision of the cyclic redundancy check. A value of 'crc16' is a 16-bit CRC calculation. A value of 'crc32' is a 32-bit CRC calculation. 32-bit CRC increases the error detection ability, but it also adds some performance overhead. For ATM channels, crc32 is the default and the only value supported and applies to AAL5 CRC calculation on that channel.

OBJECT-TYPE

The size of the largest packet which can be sent/received on the port, specified in octets. For ports that are used for transmitting network datagrams, this is the size of the largest network datagram that can be sent on the sonet path. Setting tmnxDS3ChannelMTU to a value of zero (0), causes the agent to recalculate the default MTU size which can vary based on the current setting of tmnxPortMode and tmnxPortEncapType variables. Some typical default values are: 1522 with mode access and encap type bcp-null 1526 with mode access and encap type bcp-dot1q 1502 with mode access and encap type ipcp 4474 with mode access and encap type frame relay 1524 with mode access and encap type atm 2092 with mode access and encap type cem

OBJECT-TYPE

The negotiated size of the largest packet which can be sent on the channel, specified in octets. For channels that are used for transmitting network datagrams, this is the size of the largest network datagram that can be sent.

OBJECT-TYPE

The value of tmnxDS3ChannelReportAlarm determines when and if to generate notifications for this channel: ais - Reports alarm indication signal errors. ais alarms are issued by default. los - Reports loss of signal errors. los alarms are issued by default. oof - Reports out-of-frame errors. oof alarms are not issued by default. rai - Reports resource availability indicator events. rai alarms are not issued by default. looped - Reports if the far end has forced the near end to loopback. looped alarms are not issued by default. berSd - Reports DS3/E3 signal degradation bit errors. berSd alarms are not issued by default. berSf - Reports DS3/E3 signal failure bit errors. berSf alarms are not issued by default

OBJECT-TYPE

The value of tmnxDS3ChannelReportAlarmStatus indicates the current alarms on this port.

OBJECT-TYPE

The tmnxDS3ChannelLastChangeTime variable contains the sysUpTime value of the most recently modified writable variable in the tmnxDS3ChannelEntry row for this port.

OBJECT-TYPE

tmnxDS3ChannelInFEACLoop indicates whether the remote end has put this channel in FEAC(Far End Alarm Control) loopback.

OBJECT-TYPE

tmnxDS3ChannelMDLMonPortString indicates the port number string received in the Message Data Link (MDL) idle signal message.

OBJECT-TYPE

tmnxDS3ChannelMDLMonGenString indicates the generator number string received in the Message Data Link (MDL) test signal message.

OBJECT-TYPE

tmnxDS3ChannelBERTOperStatus indicates the status of the BERT test as specified by TmnxDSXBertOperStatus.

OBJECT-TYPE

tmnxDS3ChannelBERTSynched is the number of seconds for which the BERT hardware was synchronized. This will be less than or equal to the duration of the last BERT test. It is valid only after tmnxDS3ChannelBERTOperStatus transitioned from 'active' to 'idle' the last time BERT was activated.

OBJECT-TYPE

tmnxDS3ChannelBERTErrors is the number of bit errors detected during the last BERT test. It is valid only after tmnxDS3ChannelBERTOperStatus transitioned from 'active' to 'idle' the last time BERT was activated.

OBJECT-TYPE

tmnxDS3ChannelBERTTotalBits is the total number of bits received during the last BERT test. Bits are only counted when the BERT hardware is synchronized. It is valid only after tmnxDS3ChannelBERTOperStatus transitioned from 'active' to 'idle' the last time BERT was activated.

OBJECT-TYPE

When tmnxDS3ChannelScramble indicates whether scrambling is enabled on this channel. Both ends of the connection must use the same scrambling algorithm. The default value is 'true' if the tmnxPortEncapType is atmEncap for this channel and indicates ATM payload scrambling; otherwise (tmnxPortEncapType is not atmEncap) the default is 'false' and can only be changed to true if the value of tmnxDS3ChannelSubrateCSUMode is digital-link (1)

OBJECT-TYPE

The value of tmnxDS3ChannelAcctPolicyId specifies an existing accounting policy to use for the ds3 channel. Accounting policies can only be associated with network ports or channels. A non-zero value indicates the tmnxLogApPolicyId index identifying the policy entry in the tmnxLogApTable from the TIMETRA-LOG-MIB which is associated with this channel. A zero value indicates that there is no accounting policy associated with this channel

OBJECT-TYPE

The value of tmnxDS3ChannelCollectStats specifies whether or not the collection of accounting and statistical data for the network ds3 channel is collected. When the value is set to false, the statistics are still accumulated by the IOM cards, however, the CPM will not obtain the results and write them to the billing file. When applying accounting policies the data by default will be collected in the appropriate records and written to the designated billing file.

OBJECT-TYPE

The value of tmnxDS3ChannelClockSyncState indicates the current clock synchronization state if tmnxDS3ChannelClockSource is 'adaptive' or 'differential'.

OBJECT-TYPE

The value of tmnxDS3ChannelClockMasterPortId indicates the current clock synchronization master port id if tmnxDS3ChannelClockSource is 'adaptive' or 'differential'.

OBJECT-TYPE

The tmnxDS1Table has an entry for each DS1 channel.

OBJECT-TYPE

Each row entry represents a DS1 channel on a IOM card in a chassis in the system. DS1 channel entries for DS3 ports cannot be created and deleted via SNMP SET operations. Entries in this table will be created automatically when tmnxDS3ChannelChannelized is set to 'true'. DS1 channel entries for DS1 ports can be created and deleted via SNMP SET operations. For each tmnxDS1Entry, there will be a corresponding entry in the tmnxPortTable and the ifTable.

OBJECT-TYPE

tmnxDS1RowStatus controls the creation and deletion of row entries in the tmnxDS1Table. For row creation, the manager has to first calculate the tmnxPortPortID based on the TiMOS encoding scheme.

OBJECT-TYPE

The value of tmnxDS1Type indicates whether the DS1 channel is in DS1, E1 or J1 mode.

OBJECT-TYPE

The value of tmnxDS1Framing specifies the type of framing associated with the channel: esf ESF (extended super frame) mode for T1 interfaces. sf SF (super frame) mode for T1 interfaces. g704 G.704 framing format for E1 interfaces. g704-no-crc4 G.704 framing with no CRC4 for E1 interfaces. e1-unframed E1 Unframed (G.703) mode for E1 interfaces. ds1-unframed Unframed mode for T1 interfaces. If tmnxDS1Type is set to 'ds1', the default framing is 'esf'. If tmnxDS1Type is set to 'e1', the default framing is 'g704'. Changing the value of tmnxDS1Framing resets the values of tmnxDS1BerSdThreshold and tmnxDS1BerSfThreshold to defaults and turns off reporting of berSd and berSf alarms in tmnxDS1ReportAlarm.

OBJECT-TYPE

tmnxDS1IdleCycleFlags configures the value that the DS1 channel transmits during idle cycle.

OBJECT-TYPE

tmnxDS1Loopback is used to put the channel into a loopback mode. The value of tmnxPortAdminStatus should be set to 'outOfService' in order for the loopback to be enabled. A 'line' loopback loops frames received on this port back to the remote system. A 'internal' loopback loops frames from the local system back at the framer. A 'fdlAnsi' requests loopback of type FDL ANSI T1.403. This is valid with tmnxDS1Framing set to 'esf' framing. A 'fdlBellcore' requests loopback of type FDL Bellcore TR-TSY-000312. This is valid with tmnxDS1Framing set to 'esf'. A 'inbandAnsi' requests loopback of type inband ANSI T1.403. This is valid with tmnxDS1Framing set to 'sf'.

OBJECT-TYPE

Setting tmnxDS1InvertData to 'true' causes all data bits to be inverted, to guarantee ones density. It is typically used with AMI line encoding.

OBJECT-TYPE

tmnxDS1BitErrorInsertionRate is used to insert bit errors for a BERT test. The number of error corresponds to 10^(-rate). A rate of 7 will cause an error rate of 10^(-7), or 1 error in every 10 million bits transmitted. If the value is set to 0, disables the insertion of bit errors into the BERT. Change in this value while the test is running is accepted but does not take effect until the test gets restarted.

OBJECT-TYPE

tmnxDS1BERTPattern object specifies the pattern used for the Bit Error Rate Test (BERT). The value of tmnxDS1BERTDuration indicates the duration of the test. Setting the value to 'none' terminates the test.

OBJECT-TYPE

tmnxDS1BERTDuration is used to set the duration of the BERT test.

OBJECT-TYPE

The value of tmnxDS1ReportAlarm determines when and if to generate notifications for this channel: ais - Reports alarm indication signal errors. ais alarms are issued by default. los - Reports loss of signal errors. los alarms are issued by default. oof - Reports out-of-frame errors. oof alarms are not issued by default. rai - Reports resource availability indicator events. rai alarms are not issued by default. looped - Reports if the far end has forced the near end to loopback. looped alarms are not issued by default. berSd - Reports DS1/E1/J1 signal degradation bit errors. berSd alarms are not issued by default. berSf - Reports DS1/E1/J1 signal failure bit errors. berSf alarms are not issued by default

OBJECT-TYPE

The value of tmnxDS1ReportAlarmStatus indicates the current alarms on this channel.

OBJECT-TYPE

The tmnxDS1LastChangeTime variable contains the sysUpTime value of the most recently modified writable variable in the tmnxDS1Entry row for this channel.

OBJECT-TYPE

tmnxDS1ClockSource configures the clock for transmitted data from either the internal clock ('nodeTimed'), or from a clock recovered from the line's receive data stream ('loopTimed'), or recovered adaptively from the rate at which the data that is received and not from the physical layer ('adaptive'), or recovered from the differential timestamp in the RTP header ('differential').

OBJECT-TYPE

tmnxDS1BERTOperStatus indicates the status of the BERT test as specified by TmnxDSXBertOperStatus.

OBJECT-TYPE

tmnxDS1BERTSynched is the number of seconds for which the BERT hardware was synchronized. This will be less than or equal to the duration of the last BERT test. It is valid only after tmnxDS1BERTOperStatus transitioned from 'active' to 'idle' the last time BERT was activated.

OBJECT-TYPE

tmnxDS1BERTErrors is the number of bit errors detected during the last BERT test. It is valid only after tmnxDS1BERTOperStatus transitioned from 'active' to 'idle' the last time BERT was activated.

OBJECT-TYPE

tmnxDS1BERTTotalBits is the total number of bits received during the last BERT test. Bits are only counted when the BERT hardware is synchronized. It is valid only after tmnxDS1BERTOperStatus transitioned from 'active' to 'idle' the last time BERT was activated.

OBJECT-TYPE

When tmnxDS1RemoteLoopRespond has a value of 'true', the channel is enabled to respond to remote loop signals. When it has a value of 'false' the port will not respond.

OBJECT-TYPE

tmnxDS1InRemoteLoop indicates whether the remote end has put this channel in remote loopback.

OBJECT-TYPE

tmnxDS1InsertSingleBitError is used to insert a single bit error for a BERT test.

OBJECT-TYPE

The value of tmnxDS1SignalMode specifies the type of signalling associated with the channel: none - Indicates no signalling on this channel. cas - Indicates Channel Associated Signalling (CAS) on this channel. The default signalling is 'none'.

OBJECT-TYPE

The value of tmnxDS1ClockSyncState indicates the current clock synchronization state if tmnxDS1ClockSource is 'adaptive' or 'differential'.

OBJECT-TYPE

The value of tmnxDS1ClockMasterPortId indicates the current clock synchronization master port id if tmnxDS1ClockSource is 'adaptive' or 'differential'.

OBJECT-TYPE

The value of tmnxDS1BerSdThreshold specifies a bit error rate (BER) threshold used to determine when to send a tmnxEqPortDS1Alarm notification for a BER SD failure and a tmnxEqPortDS1AlarmClear notification for a BER SD failure clear. Bit error computed must reach/exceed threshold value over a predefined period of time for the tmnxEqPortSonetAlarm notification to be sent. The value of tmnxDS1Framing defines how the bit error is computed and what values of tmnxDS1BerSdThreshold are allowed. The following table defines this dependency: tmnxDS1Framing Bit error calculation and value supported -------------- ----------------------------------------- esf (1) each CRC error is counted as one bit error g704 (4) values supported are 1,5,10,50,100 other values bit error alarms not supported, value of tmnxDS1BerSdThreshold set to default and cannot be changed tmnxDS1BerSdThreshold value must not exceed the value of tmnxDS1BerSfThreshold.

OBJECT-TYPE

The value of tmnxDS1BerSfThreshold specifies a bit error rate (BER) threshold used to determine when to send a tmnxEqPortDS1Alarm notification for a BER SF failure and a tmnxEqPortDS1AlarmClear notification for a BER SF failure clear. Bit error computed must reach/exceed threshold value over a predefined period of time for the tmnxEqPortSonetAlarm notification to be sent. The value of tmnxDS1Framing defines how the bit errors are computed and what values of tmnxDS1BerSfThreshold are allowed. The following table defines this dependency: tmnxDS1Framing Bit error calculation and value supported -------------- ----------------------------------------- esf (1) each CRC error is counted as one bit error g704 (4) values supported are 1,5,10,50,100 other values bit error alarms not supported, value of tmnxDS1BerSfThreshold set to default and cannot be changed tmnxDS1BerSfThreshold value must not be smaller than tmnxDS1BerSdThreshold value

OBJECT-TYPE

The tmnxDS1NationalUseBits specifies the transmitted value for each of the E1 national use bits (Sa4 to Sa8). This object is only applicable on E1 channels with tmnxDS1Framing set to g704-no-crc (3), or g704 (4).

OBJECT-TYPE

The value of tmnxDS1HoldTimeUp specifies the hold-timer for link up event dampening. A value of zero (0) indicates that an up transition is reported immediately.

OBJECT-TYPE

The value of tmnxDS1HoldTimeDown specifies the hold-timer for link down event dampening. A value of zero (0) indicates that a down transition is reported immediately.

OBJECT-TYPE

The tmnxDS0ChanGroupTable has an entry for DS0 channels grouped together and belonging to a particular DS1 channel.

OBJECT-TYPE

Each row entry represents one or more DS0 channels on a DS1 interface. tmnxDS0ChanGroupTimeSlots object is used to add or remove DS0 channels from the group. Entries can be created and deleted via SNMP SET operations using the tmnxDS0ChanGroupRowStatus object. For each tmnxDS0ChanGroupEntry, there will be a corresponding entry in the tmnxPortTable and the ifTable.

OBJECT-TYPE

tmnxDS0ChanGroupRowStatus controls the creation and deletion of row entries in the tmnxDS0ChanGroupTable. The tmnxPortPortID for a channel group includes a group ID in the lower bits. The manager has to first calculate the tmnxPortPortID based on the TiMOS encoding scheme.

OBJECT-TYPE

tmnxDS0ChanGroupTimeSlots is a bitmap which is used to add/remove DS0 timeslots from a channel group. The description for TmnxDs0ChannelList contains details of the bitmap organization. When a channel group is created on unframed DS1/E1, all timeslots as applicable to a given speed are auto-allocated and cannot be changed. When a channel group is created on a framed DS1/E1 or existing channel group's encapsulation is changed from ATM, the default of no timeslots is auto-assigned to the group. When a channel group on a framed DS1/E1 is configured for ATM encapsulation, the ATM defaults of 0x00FFFFFF (DS1) and 0XFFFEFFFE (E1) are auto-assigned and cannot be changed.

OBJECT-TYPE

tmnxDS0ChanGroupSpeed configures the required link speed for all the time slots included in this channel group.

OBJECT-TYPE

The value of tmnxDS0ChanGroupCRC variable specifies the precision of the cyclic redundancy check. A value of 'crc16' is a 16-bit CRC calculation. A value of 'crc32' is a 32-bit CRC calculation. 32-bit CRC increases the error detection ability, but it also adds some performance overhead. For channel groups with encapsulation set to ATM, the default and only supported value is crc32 and applies to AAL5 CRC calculations on that channel group.

OBJECT-TYPE

The size of the largest packet which can be sent/received on the channel group, specified in octets. For groups that are used for transmitting network datagrams, this is the size of the largest network datagram that can be sent. Setting tmnxDS0ChanGroupMTU to a value of zero (0), causes the agent to recalculate the default MTU size which can vary based on the current setting of tmnxPortMode and tmnxPortEncapType variables. Some typical default values are: 1522 with mode access and encap type bcp-null 1526 with mode access and encap type bcp-dot1q 1502 with mode access and encap type ipcp 4474 with mode access and encap type frame relay 1524 with mode access and encap type atm 2092 with mode access and encap type cem

OBJECT-TYPE

The negotiated size of the largest packet which can be sent on the channel group, specified in octets. For channel groups that are used for transmitting network datagrams, this is the size of the largest network datagram that can be sent.

OBJECT-TYPE

The tmnxDS0ChanGroupLastChangeTime variable contains the sysUpTime value of the most recently modified writable variable in the tmnxDS0ChanGroupEntry row for this channel group.

OBJECT-TYPE

tmnxDS0ChanGroupIdleCycleFlags configures the value that the channel group transmits during idle cycle. The default value applies to HDLC channels only. For ATM and CEM channels the object does not really apply so a default value of 'none' is used and cannot be changed.

OBJECT-TYPE

tmnxDS0ChanGroupScramble indicates whether payload scrambling is enabled on this ATM channel. Both ends of the connection must use the same scrambling algorithm. The default value is 'true' if the tmnxPortEncapType is atmEncap for this channel, otherwise the default is 'false' and not allowed to change.

OBJECT-TYPE

The value of tmnxDS0ChanGroupAcctPolicyId specifies an existing accounting policy to use for the ds0 channel-group. Accounting policies can only be associated with network ports or channels. A non-zero value indicates the tmnxLogApPolicyId index identifying the policy entry in the tmnxLogApTable from the TIMETRA-LOG-MIB which is associated with this channel-group. A zero value indicates that there is no accounting policy associated with this channel

OBJECT-TYPE

The value of tmnxDS0ChanGroupCollectStats specifies whether or not the collection of accounting and statistical data for the network ds0 channel-group is collected. When the value is set to false, the statistics are still accumulated by the IOM cards, however, the CPM will not obtain the results and write them to the billing file. When applying accounting policies the data by default will be collected in the appropriate records and written to the designated billing file.

OBJECT-TYPE

The value of tmnxDS0ChanGroupPayloadFillType specifies the type of idle payload fill to be sent when the CEM channel group experiences an underrun. If the type is set to 'userDefinedPattern' then the value of tmnxDS0ChanGroupPayloadPattern is used to define the payload pattern. The default value depends on the encap type of the channel group: For CEM encap - 'allOnes' For all other encaps - 'notApplicable' For a ds1-unframed and e1-unframed CEM encap DS0 channel group the only supported value is 'allOnes'. For non-CEM encap channel groups the value cannot be changed.

OBJECT-TYPE

The value of tmnxDS0ChanGroupPayloadPattern specifies the idle payload fill pattern when the CEM channel group experiences an underrun and tmnxDS0ChanGroupPayloadFillType is set to 'userDefinedPattern'. The default value depends on the encap type of the channel group: For CEM encap channel group - 255 (Valid range 0..255) For non-CEM encap channel group - 0 (Valid range 0..0).

OBJECT-TYPE

The value of tmnxDS0ChanGroupSignalFillType specifies the type of idle signal fill to be sent when the CAS CEM channel group experiences an underrun. If the type is set to 'userDefinedPattern' then the value of tmnxDS0ChanGroupSignalPattern is used to define the signal pattern. The default value depends on the encap of the DS0 channel group and the signal mode of the DS1/E1: For CEM encap on DS1/E1 with CAS signal mode - 'allOnes' For all other encaps or non-CAS CEM DS1/E1 - 'notApplicable' For CEM channel groups on DS1/E1 with no CAS signalling and non-CEM encap channel groups the value cannot be changed.

OBJECT-TYPE

The value of tmnxDS0ChanGroupSignalPattern specifies the idle signal fill pattern when the CAS CEM channel group experiences an underrun and tmnxDS0ChanGroupSignalFillType is set to 'userDefinedPattern'. CAS ESF DS1 and CAS E1 support 4 signalling bits per timeslot (ABCD) CAS SF DS1 supports 2 signalling bits per timeslot (AB) The default value depends on the type of channel group: For CAS DS1 ESF or CAS E1 channel group - 15 (Valid range 0..15) For CAS DS1 SF channel group - 3 (Valid range 0..3) For non-CAS or non-CEM channel group - 0 (Valid range 0..0)

OBJECT-TYPE

The value of tmnxDS0ChanGroupBerSfLinkDown specifies whether or not the DS0 channel-group will become operationally down when a BER-SF alarm is raised. If tmnxDS0ChanGroupBerSfLinkDown is false then the channel-group will not operationally change state due to BER-SF alarms.

OBJECT-TYPE

The tmnxBundleTable has an entry for a bundle created on the system.

OBJECT-TYPE

Each row entry represents a multilink bundle on a MDA. Entries can be created and deleted via SNMP SET operations using the tmnxBundleRowStatus object. The tmnxBundleBundleID will contain the bundle number encoded in it. The bundle number is unique for a MDA. For each tmnxBundleEntry, there will be a corresponding entry in the tmnxPortTable and the ifTable.

OBJECT-TYPE

tmnxBundleBundleID identifies this multilink bundle. The value of this object is calculated using the TiMOS encoding scheme described in TmnxBundleID. tmnxBundleBundleID is used as an index into the ifTable and the tmnxPortTable to access an entry corresponding to this entry.

OBJECT-TYPE

tmnxBundleRowStatus controls the creation and deletion of row entries in the tmnxBundleTable. The manager has to first calculate the tmnxBundleBundleID based on the TiMOS encoding.

OBJECT-TYPE

tmnxBundleType specifies the type of this multilink bundle. It provides a reference as to the type of bundle this row refers to but does not map to the direct value of bundle type defined in TmnxBundleID.

OBJECT-TYPE

tmnxBundleMinimumLinks is the minimum number of links that must be active for a bundle to be active. If the number of links drop below the given minimum then the multilink bundle will transition to an operation down state.

OBJECT-TYPE

tmnxBundleNumLinks indicates the total number of links configured for this bundle.

OBJECT-TYPE

tmnxBundleNumActiveLinks indicates the current number of active links belonging to this bundle.

OBJECT-TYPE

tmnxBundleMRRU is used to configure the Max Received Reconstructed Unit (MRRU). This is the maximum frame that can be reconstructed from multilink fragments. This object is only applicable to tmnxBundleType value of mlppp. All non applicable types have a value of zero.

OBJECT-TYPE

tmnxBundleOperMRRU indicates the operational value of Max Received Reconstructed Unit (MRRU). This object is only applicable to tmnxBundleType value of mlppp. All non applicable types have a value of zero.

OBJECT-TYPE

tmnxBundlePeerMRRU indicates the MRRU value sent by the peer during negotiation. This object is only applicable to tmnxBundleType value of mlppp. All non applicable types have a value of zero.

OBJECT-TYPE

tmnxBundleOperMTU indicates the operational MTU of the bundle.

OBJECT-TYPE

tmnxBundleRedDiffDelay configures the maximum acceptable differential delay for individual circuits within this multilink bundle. If the delay exceeds this threshold, a tmnxEqPortBndlRedDiffExceeded trap is issued. For a tmnxBundleType value of 'imagrp' a range of 0 to 50 is supported, 0 to 25 otherwise.

OBJECT-TYPE

tmnxBundleRedDiffDelayAction specifies the action to be taken when the differential delay exceeds the threshold configured in tmnxBundleRedDiffDelay. For a tmnxBundleType value of 'imagrp', only the down action is supported.

OBJECT-TYPE

tmnxBundleYellowDiffDelay configures the yellow warning threshold for the differential delay for the circuits within a given multilink bundle. If the delay exceeds this threshold, a tmnxEqPortBndlYellowDiffExceeded trap is issued. This object is only applicable to tmnxBundleType values of 'mlppp' or 'mlfr'. All non applicable types have a value of zero.

OBJECT-TYPE

tmnxBundleShortSequence command specifies that the MLPPP bundle should use short (12 bit) sequence numbers. Instead of the standard long (24 bits) sequence number. This object is only applicable to tmnxBundleType value of mlppp.

OBJECT-TYPE

The tmnxBundleLastChangeTime variable contains the sysUpTime value of the most recently modified writable variable in the tmnxBundleEntry row for this channel group.

OBJECT-TYPE

The value of tmnxBundleFragmentThreshold specifies the maximum length of a fragment transmitted across the multilink bundle. Values supported within each bundle type are hardware dependent. The value of 0 specifies no fragmentation. Currently, the following values are supported depending upon the tmnxBundleType value: tmnxBundleType tmnxBundleFragmentThreshold values supported mlppp 0; 128 to 512 inclusive imagrp 128 mlfr 0; 128 to 512 inclusive

OBJECT-TYPE

tmnxBundleUpTime indicates the time since the bundle is operationally 'inService'.

OBJECT-TYPE

tmnxBundleInputDiscards indicates the number of LCP packets that were discarded. This object is only supported for a tmnxBundleType value of mlppp.

OBJECT-TYPE

tmnxBundlePrimaryMemberPortID indicates the TmnxPortID of the primary member of this bundle. The value of this object will be zero if there are no members configured in this bundle.

OBJECT-TYPE

tmnxBundleLFI specifies if Link Fragmentation and Interleaving is enabled on the multilink bundle. A value of 'false' indicates that Link Fragmentation and Interleaving is disabled on the multilink bundle while a value of 'true' indicates that Link Fragmentation and Interleaving is enabled on the multilink bundle. This object is only supported for tmnxBundleType value of mlppp. The value of tmnxBundleLFI may be modified only when no members are part of the bundle. This object cannot be set to true when tmnxBundleMlpppClassCount object value is set to enable Multiclass MLPPP on the bundle.

OBJECT-TYPE

tmnxBundleProtectedType identifies how this bundle is part of a tmnxBundleParentBundle. A value of 'none' identifies no protection, 'working' identifies it to be a working bundle of a tmnxBundleParentBundle and 'protection' identifies it to be a protection bundle of a tmnxBundleParentBundle. tmnxBundleProtectedType can only be set at row creation.

OBJECT-TYPE

tmnxBundleParentBundle specifies the parent to which this bundle belongs. A row for the given non zero value of tmnxBundleParentBundle must exist for this row to be successfully created. If a bundle has no parent, its value is zero. tmnxBundleParentBundle can only be set at row creation.

OBJECT-TYPE

The tmnxBundleMemberTable has an entry for a member port associated with a multilink bundle.

OBJECT-TYPE

Each row represents a port associated with a bundle. Entries can be added or removed from this table using SNMP SET operation.

OBJECT-TYPE

tmnxBundleMemberRowStatus controls the creation and deletion of row entries in the tmnxBundleMemberTable. tmnxPortPortID identifies the port to be associated with the bundle. A bundle entry with tmnxBundleBundleID has to exist in the tmnxBundleTable before creating an entry in this table.

OBJECT-TYPE

tmnxBundleMemberActive is set to 'false' for one of reasons in tmnxBundleMemberDownReason.

OBJECT-TYPE

tmnxBundleMemberDownReason contains the reason code for marking the member link of the bundle to down (i.e. tmnxBundleMemberActive will be set to false): none - The link is active and the value of tmnxBundleMemberActive is 'true'. outOfService - The link operational status is down. redDiffDelayExceeded - The differential delay of the link exceeded the configured value of red differential delay and tmnxBundleRedDiffDelayAction was configured as 'down'. mismatchEndPtDiscriminator - Detected inconsistent peer endpoint discriminator for the bundle. peerNotBundleMember - When the peer is either not added to the bundle or is removed from the bundle. underNegotiation - When the local end is trying to negotiate with the peer. peerInvalidMlHdrFmt - The peer does not support the required ML-PPP header format. The remote peer must support the same short/long sequence code, and at least as many classes as configured for the local bundle. other - Refer to the corresponding member table, if any, for more information based on the tmnxBundleType.

OBJECT-TYPE

tmnxBundleMemberUpTime indicates the time since the bundle member is active as indicated by tmnxBundleMemberActive.

OBJECT-TYPE

The tmnxPortToChannelTable is a mapping table. Given a chassis index, physical port index and channel string, it maps it to the index of the channel. This channel index can then be used as an index into the ifTable or the tmnxPortTable.

OBJECT-TYPE

Each row represents a mapping of the physical port index and the channel index string to the index of the channel.

OBJECT-TYPE

tmnxChannelIdxString is an index into the table. It contains a string identifying a channel on the physical port.

OBJECT-TYPE

tmnxChannelPortID contains the port ID of the channel. This value is used to identify the entry for this channel in the ifTable or the tmnxPortTable.

OBJECT-TYPE

The table tmnxPortIngrMdaQosStatTable contains a row for each ethernet or SONET/SDH port located on an oversubscribed MDA. Each object in a row refers to a QoS priority and forwarding class, which is a decimal value between 00 and 15 inclusive. The following table describes each decimal value: | Priority |------------------ Forwarding Class | High Low ---------------------------------------- NC (Network Control) | 00 01 H1 (Voice) | 02 03 EF (Premium) | 04 05 H2 (Video) | 06 07 L1 (Management) | 08 09 AF (Assured) | 10 11 L2 (Priority) | 12 13 BE (Best Effort) | 14 15

OBJECT-TYPE

Each row indicates the MDA QoS discard statistics on an ethernet or SONET/SDH port located on an oversubscribed MDA. For ethernet ports, the tmnxPortEtherIngressRate object indicates the ingress shaping rate configured.

OBJECT-TYPE

tmnxPortIngrMdaQos00StatDropPkts indicates the number of packets dropped on the oversubscribed MDA for QoS classifier result threshold 00 because of an overload condition on the MDA.

OBJECT-TYPE

tmnxPortIngrMdaQos00StatDropOcts indicates the number of octets dropped on the oversubscribed MDA for QoS classifier result threshold 00 because of an overload condition on the MDA.

OBJECT-TYPE

tmnxPortIngrMdaQos01StatDropPkts indicates the number of packets dropped on the oversubscribed MDA for QoS classifier result threshold 01 because of an overload condition on the MDA.

OBJECT-TYPE

tmnxPortIngrMdaQos01StatDropOcts indicates the number of octets dropped on the oversubscribed MDA for QoS classifier result threshold 01 because of an overload condition on the MDA.

OBJECT-TYPE

tmnxPortIngrMdaQos02StatDropPkts indicates the number of packets dropped on the oversubscribed MDA for QoS classifier result threshold 02 because of an overload condition on the MDA.

OBJECT-TYPE

tmnxPortIngrMdaQos02StatDropOcts indicates the number of octets dropped on the oversubscribed MDA for QoS classifier result threshold 02 because of an overload condition on the MDA.

OBJECT-TYPE

tmnxPortIngrMdaQos03StatDropPkts indicates the number of packets dropped on the oversubscribed MDA for QoS classifier result threshold 03 because of an overload condition on the MDA.

OBJECT-TYPE

tmnxPortIngrMdaQos03StatDropOcts indicates the number of octets dropped on the oversubscribed MDA for QoS classifier result threshold 03 because of an overload condition on the MDA.

OBJECT-TYPE

tmnxPortIngrMdaQos04StatDropPkts indicates the number of packets dropped on the oversubscribed MDA for QoS classifier result threshold 04 because of an overload condition on the MDA.

OBJECT-TYPE

tmnxPortIngrMdaQos04StatDropOcts indicates the number of octets dropped on the oversubscribed MDA for QoS classifier result threshold 04 because of an overload condition on the MDA.

OBJECT-TYPE

tmnxPortIngrMdaQos05StatDropPkts indicates the number of packets dropped on the oversubscribed MDA for QoS classifier result threshold 05 because of an overload condition on the MDA.

OBJECT-TYPE

tmnxPortIngrMdaQos05StatDropOcts indicates the number of octets dropped on the oversubscribed MDA for QoS classifier result threshold 05 because of an overload condition on the MDA.

OBJECT-TYPE

tmnxPortIngrMdaQos06StatDropPkts indicates the number of packets dropped on the oversubscribed MDA for QoS classifier result threshold 06 because of an overload condition on the MDA.

OBJECT-TYPE

tmnxPortIngrMdaQos06StatDropOcts indicates the number of octets dropped on the oversubscribed MDA for QoS classifier result threshold 06 because of an overload condition on the MDA.

OBJECT-TYPE

tmnxPortIngrMdaQos07StatDropPkts indicates the number of packets dropped on the oversubscribed MDA for QoS classifier result threshold 07 because of an overload condition on the MDA.

OBJECT-TYPE

tmnxPortIngrMdaQos07StatDropOcts indicates the number of octets dropped on the oversubscribed MDA for QoS classifier result threshold 07 because of an overload condition on the MDA.

OBJECT-TYPE

tmnxPortIngrMdaQos08StatDropPkts indicates the number of packets dropped on the oversubscribed MDA for QoS classifier result threshold 08 because of an overload condition on the MDA.

OBJECT-TYPE

tmnxPortIngrMdaQos08StatDropOcts indicates the number of octets dropped on the oversubscribed MDA for QoS classifier result threshold 08 because of an overload condition on the MDA.

OBJECT-TYPE

tmnxPortIngrMdaQos09StatDropPkts indicates the number of packets dropped on the oversubscribed MDA for QoS classifier result threshold 09 because of an overload condition on the MDA.

OBJECT-TYPE

tmnxPortIngrMdaQos09StatDropOcts indicates the number of octets dropped on the oversubscribed MDA for QoS classifier result threshold 09 because of an overload condition on the MDA.

OBJECT-TYPE

tmnxPortIngrMdaQos10StatDropPkts indicates the number of packets dropped on the oversubscribed MDA for QoS classifier result threshold 10 because of an overload condition on the MDA.

OBJECT-TYPE

tmnxPortIngrMdaQos10StatDropOcts indicates the number of octets dropped on the oversubscribed MDA for QoS classifier result threshold 10 because of an overload condition on the MDA.

OBJECT-TYPE

tmnxPortIngrMdaQos11StatDropPkts indicates the number of packets dropped on the oversubscribed MDA for QoS classifier result threshold 11 because of an overload condition on the MDA.

OBJECT-TYPE

tmnxPortIngrMdaQos11StatDropOcts indicates the number of octets dropped on the oversubscribed MDA for QoS classifier result threshold 11 because of an overload condition on the MDA.

OBJECT-TYPE

tmnxPortIngrMdaQos12StatDropPkts indicates the number of packets dropped on the oversubscribed MDA for QoS classifier result threshold 12 because of an overload condition on the MDA.

OBJECT-TYPE

tmnxPortIngrMdaQos12StatDropOcts indicates the number of octets dropped on the oversubscribed MDA for QoS classifier result threshold 12 because of an overload condition on the MDA.

OBJECT-TYPE

tmnxPortIngrMdaQos13StatDropPkts indicates the number of packets dropped on the oversubscribed MDA for QoS classifier result threshold 13 because of an overload condition on the MDA.

OBJECT-TYPE

tmnxPortIngrMdaQos13StatDropOcts indicates the number of octets dropped on the oversubscribed MDA for QoS classifier result threshold 13 because of an overload condition on the MDA.

OBJECT-TYPE

tmnxPortIngrMdaQos14StatDropPkts indicates the number of packets dropped on the oversubscribed MDA for QoS classifier result threshold 14 because of an overload condition on the MDA.

OBJECT-TYPE

tmnxPortIngrMdaQos14StatDropOcts indicates the number of octets dropped on the oversubscribed MDA for QoS classifier result threshold 14 because of an overload condition on the MDA.

OBJECT-TYPE

tmnxPortIngrMdaQos15StatDropPkts indicates the number of packets dropped on the oversubscribed MDA for QoS classifier result threshold 15 because of an overload condition on the MDA.

OBJECT-TYPE

tmnxPortIngrMdaQos15StatDropOcts indicates the number of octets dropped on the oversubscribed MDA for QoS classifier result threshold 15 because of an overload condition on the MDA.

OBJECT-TYPE

The tmnxSonetGroupTable has an entry for each Tributary Unit Group(TUG3) on a path. On a port which supports unchannelized STS-3's, rows in this table are created when a channelized STS-3 has its tmnxSonetPathChildType set to sdhTug3. On a port which does not support unchannelized STS-3's, the rows in this table are implicitly created when a STS-3 is created in the tmnxSonetPathTable. Entries in this table are implicitly deleted when the parent entry of this group is deleted from the tmnxSonetPathTable or if the tmnxSonetPathChildType of the parent is set to something other than sdhTug3.

OBJECT-TYPE

Each row entry represents a Tributary Unit Group(TUG3) on a path.

OBJECT-TYPE

tmnxSonetGroupType indicates the sonet group type of this entry. For STS-3/STM-1 channelization, the value of this object will be 'sdhTug3'.

OBJECT-TYPE

tmnxSonetGroupParentPortID indicates the TmnxPortID of the parent of this group.

OBJECT-TYPE

tmnxSonetGroupChildType is used to configure the type of the children of this group. Based on the value of this object, entries of a certain channel type can be created in the tmnxSonetPathTable. For example, if the value of this object is set to 'sonetVt15', then 28 entries of type 'sonetVt15' can be created in the tmnxSonetPathTable.

OBJECT-TYPE

tmnxSonetGroupName is the textual name for this sonet group.

OBJECT-IDENTITY

OBJECT-TYPE

The value of tmnxL4LoadBalancing specifies whether layer 4 information, src and dst ports, should be used in the LAG and ECMP hashing algorithm. This is the global system setting that all ports will inherit. When set to 'true', src and dst ports are used in the hashing algorithm. The per port setting of tmnxPortLoadBalanceAlgorithm can override tmnxL4LoadBalancing.

OBJECT-TYPE

The value of tmnxLsrIpLoadBalancing specifies whether the IP Header is used in the LAG and ECMP LSR hashing algorithm. This is the global system setting that all ports will inherit. When set to 'label-ip (2)', the IP Header is included in the hashing algorithm. When set to 'ip-only (3)' the IP Header is used exclusively in the hashing algorithm. When set to 'eth-encap-ip (4)' the IP SA/DA fields is used in the hashing Algorithm. When set to 'label-ip-l4-teid (5)' the hashing algorithm hashes based on label, IP header, L4 header, and GTP header (TEID) in order. The hashing algorithm will use all the supported headers that are found in the header fragment of incoming traffic.

OBJECT-TYPE

The value of tmnxIpLoadBalancing specifies whether or not this node's system IP address is used in the final stage of the load balancing (hashing) algorithm used to choose the LAG member or ECMP route for an outbound packet. If 'systemIp(2)' is selected, this node's system IP address (i.e. TIMETRA-VRTR-MIB::vRiaIpAddress.1.1.1) is used in the final stage of the LAG and ECMP load balancing algorithm. This selection makes it more likely that different SROS nodes in a network will make different load balancing decisions. 'systemIp(2)' is supported on iom3-xp IOMs, equivalent IMMs, and newer IOM and IMM types. When older IOMs/IMMs are present in a system which has 'systemIp(2)' configured, the older IOMs operate in 'standard(1)' mode. If 'standard(1)' is selected, this node's system IP address is not used in the final stage of the LAG and ECMP load balancing algorithm. 'standard(1)' is supported on all IOM and IMM types. The earlier stages of the load balancing algorithm are controlled by tmnxL4LoadBalancing and tmnxLsrIpLoadBalancing (when applicable).

OBJECT-TYPE

The value of tmnxMulticastEnhLoadBalancing specifies how the node distributes multicast traffic over LAG ports. The default value, 'false (1),' preserves the behaviour prior to the introduction of this object: multicast traffic hash uses internal system multicast identifiers. This allows per multicast (S,G) channel (IP replication) or per LSP (MPLS replication) traffic distribution over LAG. The value of 'true (2)' introduces an enhanced multicast distribution over LAG: multicast traffic hash uses packet header information and configuration of other system level hashing parameters like tmnxL4LoadBalancing, tmnxLsrIpLoadBalancing, or tmnxIpLoadBalancing. The functionality allows for a greater flexibility in defining how multicast is to be distributed over a LAG allowing, for example, per (S,G) channel distribution for both IP and MPLS replications.

OBJECT-TYPE

The value of tmnxServiceIdLagHashing specifies how the node distributes LAG link traffic in a VLL service when both ECMP and LAG load balancing are performed. The default value, 'false (1),' preserves the behaviour prior to the introduction of this object: the ingress IOM will select one ECMP interface and one LAG link for all packets on the VLL service based on a modulo of the service ID. The value of 'true (2)' introduces an enhanced distribution which hashes the service-id prior to the LAG link modulo operation. The default value, 'false (1),' preserves the behaviour prior to the introduction of this object: the ingress IOM will select one ECMP interface and one LAG link for all packets on the VLL service based on a modulo of the service ID. The value of 'true (2)' introduces an enhanced distribution for VLL services.

OBJECT-TYPE

The value of tmnxL2tpLoadBalancing specifies if the L2TP header is taken into account for the load-balancing hash.

OBJECT-TYPE

The value of tmnxLoadBalancingHashEcmpPoly specifies the CRC polynomial used in the ECMP hashing. This is the global system setting that would affect system wide ECMP hashing. The same polynomial value cannot be used by both tmnxLoadBalancingHashEcmpPoly and tmnxLoadBalancingHashLagPoly.

OBJECT-TYPE

The value of tmnxLoadBalancingHashLagPoly specifies the CRC polynomial used in the LAG hashing. This is the global system setting that affects system wide LAG hashing. The same polynomial value cannot be used by both tmnxLoadBalancingHashEcmpPoly and tmnxLoadBalancingHashLagPoly.

OBJECT-TYPE

The tmnxCiscoHDLCTable has an entry for each port in the system that is configured for Cisco HDLC. It contains the parameters related to Cisco HDLC protocol on this port.

OBJECT-TYPE

The tmnxCiscoHDLCEntry specifies parameters for a particular interfaces running Cisco HDLC encapsulation. Entries cannot be created and deleted via SNMP SET operations.

OBJECT-TYPE

tmnxCiscoHDLCKeepAliveInt specifies the interval in seconds used for sending periodic keepalive packets. The default value is set to 10 seconds. A value of 0 specifies that the keepalive function is turned off. It is expected that the nodes at the two endpoints of the Cisco HDLC link are provisioned with the same values.

OBJECT-TYPE

tmnxCiscoHDLCUpCount specifies the number of continual keepalive packets that has to be received to declare the link up. It is expected that the nodes at the two endpoints of the Cisco HDLC link are provisioned with the same values.

OBJECT-TYPE

tmnxCiscoHDLCDownCount specifies the number of 'tmnxCiscoHDLCKeepAliveInt' intervals that must pass without receiving a keepalive packet before the link is declared down. It is expected that the nodes at the two endpoints of the Cisco HDLC link are provisioned with the same values.

OBJECT-TYPE

The value of tmnxCiscoHDLCOperState indicates the operational status of the Cisco HDLC protocol for this port.

OBJECT-TYPE

The tmnxBundleImaGrpTable contains IMA Group data

OBJECT-TYPE

Each row entry contains data on an IMA Group.

OBJECT-TYPE

tmnxBundleImaGrpLnkActTimer specifies the Link Activation Timer used to clear an existing LIF, LODS and FRI-IMA alarm. The time specified determines how long is needed for member links to stabilize before being activated.

OBJECT-TYPE

tmnxBundleImaGrpLnkDeactTimer specifies the Link Deactivation Timer used to raise an LIF, LODS and FRI-IMA alarm. The time specified determines how long before a member link is declared in error and is deactivated.

OBJECT-TYPE

tmnxBundleImaGrpSymmetryMode specifies the type of cell rate transfer over the virtual link.

OBJECT-TYPE

tmnxBundleImaGrpTxId indicates the IMA Id generated at group creation time used by the near-end.

OBJECT-TYPE

tmnxBundleImaGrpRxId indicates the IMA ID generated at group creation time used by the far-end.

OBJECT-TYPE

tmnxBundleImaGrpTxRefLnk indicates the IMA bundle member that was selected to be the transmit timing reference link. If no member has been selected as the reference link a value of zero is returned.

OBJECT-TYPE

tmnxBundleImaGrpRxRefLnk indicates the IMA bundle member that was detected to be the receive timing reference link. If no member has been detected as the reference link a value of zero is returned.

OBJECT-TYPE

tmnxBundleImaGrpSmNeState indicates the current state of the IMA Group for the near-end.

OBJECT-TYPE

tmnxBundleImaGrpSmFeState indicates the current state of the IMA Group for the far-end.

OBJECT-TYPE

tmnxBundleImaGrpSmFailState indicates the current state of the IMA Group.

OBJECT-TYPE

tmnxBundleImaGrpSmDownSecs indicates the number of seconds that the IMA Group State Machine is not Operational.

OBJECT-TYPE

tmnxBundleImaGrpSmOperSecs indicates the number of seconds that the IMA Group State Machine has been in the Operational State.

OBJECT-TYPE

tmnxBundleImaGrpAvailTxCR indicates the available transmit bandwidth on this IMA group. It only considers members that are in the Active State.

OBJECT-TYPE

tmnxBundleImaGrpAvailRxCR indicates the available bandwidth on this IMA group in the receive direction. It only considers members that are in the Active State.

OBJECT-TYPE

tmnxBundleImaGrpNeFails indicates the number of reported IMA Group failures since boot time.

OBJECT-TYPE

tmnxBundleImaGrpFeFails indicates the number of reported IMA Group far-end failures since boot time.

OBJECT-TYPE

tmnxBundleImaGrpTxIcpCells indicates number of transmitted ICP cells for this IMA Group.

OBJECT-TYPE

tmnxBundleImaGrpRxIcpCells indicates number of received ICP cells for this IMA Group.

OBJECT-TYPE

tmnxBundleImaGrpErrorIcpCells indicates number of ICP cells with HEC or CRC-10 errors.

OBJECT-TYPE

tmnxBundleImaGrpLostRxIcpCells indicates the number of missing ICP cells at the expected offset.

OBJECT-TYPE

tmnxBundleImaGrpTxOamLablVal indicates near-end value to be transmitted.

OBJECT-TYPE

tmnxBundleImaGrpRxOamLablVal indicates far-end value received.

OBJECT-TYPE

tmnxBundleImaGrpAlphaValue specifies the number of consecutive ICP cells that need to be detected before moving from the IMA Sync State to the IMA Hunt State.

OBJECT-TYPE

tmnxBundleImaGrpBetaValue specifies the number of consecutive errored ICP cells that need to be detected before moving from the IMA Sync State to the IMA Hunt State

OBJECT-TYPE

tmnxBundleImaGrpGammaValue specifies the number of consecutive valid ICP cells that need to be detected before moving from the IMA pre-Sync State to the IMA Hunt State.

OBJECT-TYPE

tmnxBundleImaGrpNeClockMode specifies near-end transmit clock mode.

OBJECT-TYPE

tmnxBundleImaGrpFeClockMode specifies far-end transmit clock mode.

OBJECT-TYPE

tmnxBundleImaGrpVersion specifies the IMA Version for this group.

OBJECT-TYPE

tmnxBundleImaGrpMaxConfBw specifies the number of links that is used to determine the maximum configurable bandwidth that is allowed to be used for this IMA group.

OBJECT-TYPE

tmnxBundleImaGrpTestState specifies the current state of the test pattern procedure. A value of 'disabled' specifies that the group is currently not running. A value of 'operating' enables the test pattern procedure. The test pattern procedure continues until it is 'disabled'.

OBJECT-TYPE

tmnxBundleImaGrpTestMember specifies a member link to be used for the test pattern procedure. A value of zero indicates that no member link has been selected. When tmnxBundleImaGrpTestState does not have the value 'disabled', an attempt to set this object will be rejected with an inconsistentValue error.

OBJECT-TYPE

tmnxBundleImaGrpTestPattern specifies the Transmit Test Pattern in an IMA group loopback operation. This value may only be changed when tmnxBundleImaGrpTestState is 'disabled'.

OBJECT-TYPE

tmnxBundleImaGrpDiffDelayMaxObs indicates the latest maximum differential delay observed between links having the least and most link propagation delay among the received links configured in this IMA group.

OBJECT-TYPE

tmnxBundleImaGrpLeastDelayLink indicates a member link which has the smallest link propagation delay. If this delay has yet to be determined or no member link has been configured, a value of zero is returned.

OBJECT-TYPE

The tmnxBundleMemberImaTable has an entry for an IMA link associated with an IMA Group.

OBJECT-TYPE

Each row entry represents an IMA link associated with an IMA Group.

OBJECT-TYPE

tmnxBundleMemberImaNeTxState indicates the state of near-end transmit IMA link.

OBJECT-TYPE

tmnxBundleMemberImaNeRxState indicates the state of near-end receive IMA link.

OBJECT-TYPE

tmnxBundleMemberImaFeTxState indicates the state of far-end transmit IMA link.

OBJECT-TYPE

tmnxBundleMemberImaFeRxState indicates the state of far-end receive IMA link.

OBJECT-TYPE

tmnxBundleMemberImaNeRxFailState indicates the IMA link failure reason for the near-end.

OBJECT-TYPE

tmnxBundleMemberImaFeRxFailState indicates the IMA link failure reason for the far-end.

OBJECT-TYPE

tmnxBundleMemberImaTxLid indicates the Link Identifier assigned to the transmit IMA link.

OBJECT-TYPE

tmnxBundleMemberImaRxLid indicates the Link Identifier used on the receive IMA link.

OBJECT-TYPE

tmnxBundleMemberImaViolations indicates the number of ICP violations including errored, invalid or missing ICP cells.

OBJECT-TYPE

tmnxBundleMemberImaNeSevErrSecs indicates the number of one second intervals in which thirty percent or more of the near-end ICP cells are in violation, or link defects have occurred.

OBJECT-TYPE

tmnxBundleMemberImaFeSevErrSecs indicates the number of one second intervals in which the far-end contains IMA-RDI defects.

OBJECT-TYPE

tmnxBundleMemberImaNeUnavailSecs indicates the number of unavailable seconds at the near-end.

OBJECT-TYPE

tmnxBundleMemberImaFeUnavailSecs indicates the number of unavailable seconds at the near-end.

OBJECT-TYPE

tmnxBundleMemberImaNeTxUnuseSecs indicates the number of unavailable seconds at the near-end transmit link state machine.

OBJECT-TYPE

tmnxBundleMemberImaNeRxUnuseSecs indicates the number of unavailable seconds at the near-end receive link state machine.

OBJECT-TYPE

tmnxBundleMemberImaFeTxUnuseSecs indicates the number of unavailable seconds at the far-end transmit link state machine.

OBJECT-TYPE

tmnxBundleMemberImaFeRxUnuseSecs indicates the number of unavailable seconds at the far-end receive link state machine.

OBJECT-TYPE

tmnxBundleMemberImaNeTxNumFails indicates the number of times that a near-end transmit alarm is set on the IMA link.

OBJECT-TYPE

tmnxBundleMemberImaNeRxNumFails indicates the number of times that a near-end receive alarm is set on the IMA link.

OBJECT-TYPE

tmnxBundleMemberImaFeTxNumFails indicates the number of times that a far-end transmit alarm is set on the IMA link.

OBJECT-TYPE

tmnxBundleMemberImaFeRxNumFails indicates the number of times that a far-end receive alarm is set on the IMA link.

OBJECT-TYPE

tmnxBundleMemberImaTxIcpCells indicates the number of ICP cells that have been transmitted on the IMA link.

OBJECT-TYPE

tmnxBundleMemberImaRxIcpCells indicates the number of ICP cells that have been received on the IMA link.

OBJECT-TYPE

tmnxBundleMemberImaErrorIcpCells indicates the number of ICP cells with HEC or CRC-10 errors.

OBJECT-TYPE

tmnxBundleMemberImaLstRxIcpCells indicates the number of lost ICP cells at the expected offset.

OBJECT-TYPE

tmnxBundleMemberImaOifAnomalies indicates the number of OIF anomalies at the near-end.

OBJECT-TYPE

tmnxBundleMemberImaRxTestState indicates the current state of the test pattern on this link.

OBJECT-TYPE

tmnxBundleMemberImaRxTestPattern indicates the received test pattern value on this link.

OBJECT-TYPE

tmnxBundleMemberImaRelDelay indicates the latest measured delay on this member link relative to the member link with the least delay within the same IMA group

OBJECT-TYPE

The tmnxDS1PortTable has an entry for a DS1 physical port.

OBJECT-TYPE

Each row entry represents a physical DS1 port on a IOM card in a chassis in the system. Entries cannot be created and deleted via SNMP SET operations. Entries in this table will be created automatically when the tmnxMDAAssignedType object is set to the DS1 MDA type The tmnxDS1PortEntry contains attributes that are unique to the 'ds1e1' TmnxPortType. The tmnxPortPortID contains the slot, mda and port numbers encoded into it. For each tmnxDS1PortEntry, there will be a corresponding entry in the tmnxPortTable and the ifTable.

OBJECT-TYPE

tmnxDS1PortBuildout configures the cable buildout length. A ds1 port has two settings for the DS1 cable buildout: a 'short' setting, for cable lengths of less than or equal to 655 feet, and a 'long' setting for cable lengths of greater than 655 feet. This object applies to copper-cable-based DS1 ports only.

OBJECT-TYPE

The tmnxDS1PortLastChangeTime variable contains the sysUpTime value of the most recently modified writable variable in the tmnxDS1PortEntry row for this port.

OBJECT-TYPE

tmnxDS1PortType configures the type of the physical port to 'ds1', 'e1' or 'j1'.

OBJECT-TYPE

tmnxDS1PortLineLength configuration only applies to a ds1 port configured with a 'short' buildout. tmnxDS1PortLineLength configures the length of the line (in feet). For line lengths longer than 655 feet configure the ds1 port buildout as 'long'. For 'long' buildout the following values are valid: lengthNotApplicable - Not applicable For 'short' buildout the following values are valid: length0To133 - For line length from 0 to 133 feet length134To266 - For line length from 134 to 266 feet length267To399 - For line length from 267 to 399 feet length400To533 - For line length from 400 to 533 feet length534To655 - For line length from 534 to 655 feet The default for 'long' buildout is 'lengthNotApplicable' while the default for 'short' buildout is 'length0To133'.

OBJECT-TYPE

tmnxDS1PortLbo configuration only applies to a ds1 port configured with a 'long' buildout. tmnxDS1PortLbo configures the number of decibels(dB) the transmission signal decreases over the line. For 'short' buildout the following values are valid: lboNotApplicable - Not applicable For 'long' buildout the following values are valid: lbo0dB - For 0 dB lboNeg7p5dB - For -7.5 dB lboNeg15p0dB - For -15.0 dB lboNeg22p5dB - For -22.5 dB The default for 'short' build out is 'lboNotApplicable' while the default for 'long' buildout is 'lbo0dB'

OBJECT-TYPE

tmnxDS1PortDbGain only applies to a ds1 port configured with a 'long' buildout. tmnxDS1PortDbGain shows the number of decibels the received signal is increased to compensate for loss.

OBJECT-TYPE

The value of tmnxDS1PortLineImpedance specifies the line impedance set on the physical DS1/E1 port. A DS1 port can only be set to 100 Ohms. An E1 port can only be set to 75 Ohms or 120 Ohms. The default is 120 Ohms.

OBJECT-TYPE

The value of tmnxDS1PortLineEncoding specifies the line encoding standard set on the physical DS1/E1 port. The possible values are: b8zs (1) - Bipolar (or Binary) with 8-Zero Substitution. Only applies to a DS1 port. ami (2) - Alternate Mark Inversion. Only applies to a DS1 port. hdb3 (3) - High Density Bipolar (or Binary) 3. Only applies to an E1 port. The default for DS1 ports is 'b8zs (1)', and the default for E1 ports is 'hdb3 (3)'.

OBJECT-TYPE

The tmnxPortSchedOverrideTable has an entry for each port scheduler override configured on this system.

OBJECT-TYPE

Each row represents a particular port scheduler override. Entries are created and deleted by the user.

OBJECT-TYPE

The value of tmnxPortSchedOverrideRowStatus is used for the creation and deletion of port scheduler overrides. When tmnxPortEgrPortSchedPlcy of the tmnxPortEntry indexed by the same indices of this table is an empty string, creation will fail.

OBJECT-TYPE

The value of tmnxPortSchedOverrideSchedName indicates the name of the port scheduler policy that this row entry overrides.

OBJECT-TYPE

The value of tmnxPortSchedOverrideLastChanged indicates the value of sysUpTime at the time of the most recent management change to this row.

OBJECT-TYPE

The value of tmnxPortSchedOverrideMaxRate specifies the explicit maximum frame based bandwidth limit. This object overrides TIMETRA-QOS-MIB::tPortSchedulerPlcyMaxRate. This object is obsoleted in 13.0 release and replaced by tmnxPortSchedOvrMaxRate.

OBJECT-TYPE

The value of tmnxPortSchedOverrideLvl1PIR specifies the total bandwidth limit, PIR, for priority level 1. This object overrides TIMETRA-QOS-MIB::tPortSchedulerPlcyLvl1PIR. This object is obsoleted in 13.0 release and replaced by tmnxPortSchedOvrLvl1PIR.

OBJECT-TYPE

The value of tmnxPortSchedOverrideLvl1CIR specifies the within-cir bandwidth limit for priority level 1. This object overrides TIMETRA-QOS-MIB::tPortSchedulerPlcyLvl1CIR. This object is obsoleted in 13.0 release and replaced by tmnxPortSchedOvrLvl1CIR.

OBJECT-TYPE

The value of tmnxPortSchedOverrideLvl2PIR specifies the total bandwidth limit, PIR, for priority level 2. This object overrides TIMETRA-QOS-MIB::tPortSchedulerPlcyLvl2PIR. This object is obsoleted in 13.0 release and replaced by tmnxPortSchedOvrLvl2PIR.

OBJECT-TYPE

The value of tmnxPortSchedOverrideLvl2CIR specifies the within-cir bandwidth limit for priority level 2. This object overrides TIMETRA-QOS-MIB::tPortSchedulerPlcyLvl2CIR. This object is obsoleted in 13.0 release and replaced by tmnxPortSchedOvrLvl2CIR.

OBJECT-TYPE

The value of tmnxPortSchedOverrideLvl3PIR specifies the total bandwidth limit, PIR, for priority level 3. This object overrides TIMETRA-QOS-MIB::tPortSchedulerPlcyLvl3PIR. This object is obsoleted in 13.0 release and replaced by tmnxPortSchedOvrLvl3PIR.

OBJECT-TYPE

The value of tmnxPortSchedOverrideLvl3CIR specifies the within-cir bandwidth limit for priority level 3. This object overrides TIMETRA-QOS-MIB::tPortSchedulerPlcyLvl3CIR. This object is obsoleted in 13.0 release and replaced by tmnxPortSchedOvrLvl3CIR.

OBJECT-TYPE

The value of tmnxPortSchedOverrideLvl4PIR specifies the total bandwidth limit, PIR, for priority level 4. This object overrides TIMETRA-QOS-MIB::tPortSchedulerPlcyLvl4PIR. This object is obsoleted in 13.0 release and replaced by tmnxPortSchedOvrLvl4PIR.

OBJECT-TYPE

The value of tmnxPortSchedOverrideLvl4CIR specifies the within-cir bandwidth limit for priority level 4. This object overrides TIMETRA-QOS-MIB::tPortSchedulerPlcyLvl4CIR. This object is obsoleted in 13.0 release and replaced by tmnxPortSchedOvrLvl4CIR.

OBJECT-TYPE

The value of tmnxPortSchedOverrideLvl5PIR specifies the total bandwidth limit, PIR, for priority level 5. This object overrides TIMETRA-QOS-MIB::tPortSchedulerPlcyLvl5PIR. This object is obsoleted in 13.0 release and replaced by tmnxPortSchedOvrLvl5PIR.

OBJECT-TYPE

The value of tmnxPortSchedOverrideLvl5CIR specifies the within-cir bandwidth limit for priority level 5. This object overrides TIMETRA-QOS-MIB::tPortSchedulerPlcyLvl5CIR. This object is obsoleted in 13.0 release and replaced by tmnxPortSchedOvrLvl5CIR.

OBJECT-TYPE

The value of tmnxPortSchedOverrideLvl6PIR specifies the total bandwidth limit, PIR, for priority level 6. This object overrides TIMETRA-QOS-MIB::tPortSchedulerPlcyLvl6PIR. This object is obsoleted in 13.0 release and replaced by tmnxPortSchedOvrLvl6PIR.

OBJECT-TYPE

The value of tmnxPortSchedOverrideLvl6CIR specifies the within-cir bandwidth limit for priority level 6. This object overrides TIMETRA-QOS-MIB::tPortSchedulerPlcyLvl6CIR. This object is obsoleted in 13.0 release and replaced by tmnxPortSchedOvrLvl6CIR.

OBJECT-TYPE

The value of tmnxPortSchedOverrideLvl7PIR specifies the total bandwidth limit, PIR, for priority level 7. This object overrides TIMETRA-QOS-MIB::tPortSchedulerPlcyLvl7PIR. This object is obsoleted in 13.0 release and replaced by tmnxPortSchedOvrLvl7PIR.

OBJECT-TYPE

The value of tmnxPortSchedOverrideLvl7CIR specifies the within-cir bandwidth limit for priority level 7. This object overrides TIMETRA-QOS-MIB::tPortSchedulerPlcyLvl7CIR. This object is obsoleted in 13.0 release and replaced by tmnxPortSchedOvrLvl7CIR.

OBJECT-TYPE

The value of tmnxPortSchedOverrideLvl8PIR specifies the total bandwidth limit, PIR, for priority level 8. This object overrides TIMETRA-QOS-MIB::tPortSchedulerPlcyLvl8PIR. This object is obsoleted in 13.0 release and replaced by tmnxPortSchedOvrLvl8PIR.

OBJECT-TYPE

The value of tmnxPortSchedOverrideLvl8CIR specifies the within-cir bandwidth limit for priority level 8. This object overrides TIMETRA-QOS-MIB::tPortSchedulerPlcyLvl8CIR. This object is obsoleted in 13.0 release and replaced by tmnxPortSchedOvrLvl8CIR.

OBJECT-TYPE

The value of tmnxPortSchedOverrideFlags specifies the set of attributes whose values have been overridden via management on this port scheduler. Clearing a given flag will return the corresponding overridden attribute to the value defined in the port's port scheduler policy.

OBJECT-TYPE

The value of tmnxPortSchedOvrMaxRatePercent specifies the explicit maximum frame based bandwidth limit in percentage. This object overrides TIMETRA-QOS-MIB::tPortSchedPlcyMaxRatePercent.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl1PIRPercent specifies the total bandwidth percentage, PIR percentage, for priority level 1. This object overrides TIMETRA-QOS-MIB::tPortSchedPlcyLvl1PIRPercent.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl1CIRPercent specifies the within-cir bandwidth percentage for priority level 1. This object overrides TIMETRA-QOS-MIB::tPortSchedPlcyLvl1CIRPercent.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl2PIRPercent specifies the total bandwidth percentage, PIR percentage, for priority level 2. This object overrides TIMETRA-QOS-MIB::tPortSchedPlcyLvl2PIRPercent.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl2CIRPercent specifies the within-cir bandwidth percentage for priority level 2. This object overrides TIMETRA-QOS-MIB::tPortSchedPlcyLvl2CIRPercent.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl3PIRPercent specifies the total bandwidth percentage, PIR percentage, for priority level 3. This object overrides TIMETRA-QOS-MIB::tPortSchedPlcyLvl3PIRPercent.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl3CIRPercent specifies the within-cir bandwidth percentage for priority level 3. This object overrides TIMETRA-QOS-MIB::tPortSchedPlcyLvl3CIRPercent.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl4PIRPercent specifies the total bandwidth percentage, PIR percentage, for priority level 4. This object overrides TIMETRA-QOS-MIB::tPortSchedPlcyLvl4PIRPercent.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl4CIRPercent specifies the within-cir bandwidth percentage for priority level 4. This object overrides TIMETRA-QOS-MIB::tPortSchedPlcyLvl4CIRPercent.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl5PIRPercent specifies the total bandwidth percentage, PIR percentage, for priority level 5. This object overrides TIMETRA-QOS-MIB::tPortSchedPlcyLvl5PIRPercent.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl5CIRPercent specifies the within-cir bandwidth percentage for priority level 5. This object overrides TIMETRA-QOS-MIB::tPortSchedPlcyLvl5CIRPercent.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl6PIRPercent specifies the total bandwidth percentage, PIR percentage, for priority level 6. This object overrides TIMETRA-QOS-MIB::tPortSchedPlcyLvl6PIRPercent.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl6CIRPercent specifies the within-cir bandwidth percentage for priority level 6. This object overrides TIMETRA-QOS-MIB::tPortSchedPlcyLvl6CIRPercent.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl7PIRPercent specifies the total bandwidth percentage, PIR percentage, for priority level 7. This object overrides TIMETRA-QOS-MIB::tPortSchedPlcyLvl7PIRPercent.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl7CIRPercent specifies the within-cir bandwidth percentage for priority level 7. This object overrides TIMETRA-QOS-MIB::tPortSchedPlcyLvl7CIRPercent.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl8PIRPercent specifies the total bandwidth percentage, PIR percentage, for priority level 8. This object overrides TIMETRA-QOS-MIB::tPortSchedPlcyLvl8PIRPercent.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl8CIRPercent specifies the within-cir bandwidth percentage for priority level 8. This object overrides TIMETRA-QOS-MIB::tPortSchedPlcyLvl8CIRPercent.

OBJECT-TYPE

The value of tmnxPortSchedOvrMaxRateHi specifies the upper 32 bits of the explicit maximum frame based bandwidth limit. This object overrides TIMETRA-QOS-MIB::tPortSchedPlcyMaxRate. This value should always be set along with tmnxPortSchedOvrMaxRate, otherwise an 'inconsistentValue' error is returned. When the value of tmnxPortSchedOvrMaxRateHi along with the value of tmnxPortSchedOvrMaxRate is set to 4294967295 (0xFFFFFFFF), rate indicates maximum rate.

OBJECT-TYPE

The value of tmnxPortSchedOvrMaxRate specifies the explicit maximum frame based bandwidth limit. This object overrides TIMETRA-QOS-MIB::tPortSchedPlcyMaxRate. The value of 4294967295 (0xFFFFFFFF) indicates maximum rate. When the value of tmnxPortSchedOvrMaxRateHi along with the value of tmnxPortSchedOvrMaxRate is set to 4294967295 (0xFFFFFFFF), rate indicates maximum rate.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl1PIRHi specifies the upper 32 bits of the total bandwidth limit, PIR, for priority level 1. This object overrides TIMETRA-QOS-MIB::tPortSchedPolicyLevelPIR for priority level 1 specified by TIMETRA-QOS-MIB::tPortSchedPolicyLevel. This value should always be set along with tmnxPortSchedOvrLvl1PIR, otherwise an 'inconsistentValue' error is returned. When the value of tmnxPortSchedOvrLvl1PIRHi along with the value of tmnxPortSchedOvrLvl1PIR is set to 4294967295 (0xFFFFFFFF), rate indicates maximum rate.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl1PIR specifies the total bandwidth limit, PIR, for priority level 1. This object overrides TIMETRA-QOS-MIB::tPortSchedPolicyLevelPIR for priority level 1 specified by TIMETRA-QOS-MIB::tPortSchedPolicyLevel. The value of 4294967295 (0xFFFFFFFF) indicates maximum rate. When the value of tmnxPortSchedOvrLvl1PIRHi along with the value of tmnxPortSchedOvrLvl1PIR is set to 4294967295 (0xFFFFFFFF), rate indicates maximum rate.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl1CIRHi specifies the upper 32 bits of the within-cir bandwidth limit for priority level 1. This object overrides TIMETRA-QOS-MIB::tPortSchedPolicyLevelCIR for priority level 1 specified by TIMETRA-QOS-MIB::tPortSchedPolicyLevel. This value should always be set along with tmnxPortSchedOvrLvl1CIR, otherwise an 'inconsistentValue' error is returned. When the value of tmnxPortSchedOvrLvl1CIRHi along with the value of tmnxPortSchedOvrLvl1CIR is set to 4294967295 (0xFFFFFFFF), rate indicates maximum rate.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl1CIR specifies the within-cir bandwidth limit for priority level 1. This object overrides TIMETRA-QOS-MIB::tPortSchedPolicyLevelCIR for priority level 1 specified by TIMETRA-QOS-MIB::tPortSchedPolicyLevel. The value of 4294967295 (0xFFFFFFFF) indicates maximum rate. When the value of tmnxPortSchedOvrLvl1CIRHi along with the value of tmnxPortSchedOvrLvl1CIR is set to 4294967295 (0xFFFFFFFF), rate indicates maximum rate.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl2PIRHi specifies the upper 32 bits of the total bandwidth limit, PIR, for priority level 2. This object overrides TIMETRA-QOS-MIB::tPortSchedPolicyLevelPIR for priority level 2 specified by TIMETRA-QOS-MIB::tPortSchedPolicyLevel. This value should always be set along with tmnxPortSchedOvrLvl2PIR, otherwise an 'inconsistentValue' error is returned. When the value of tmnxPortSchedOvrLvl2PIRHi along with the value of tmnxPortSchedOvrLvl2PIR is set to 4294967295 (0xFFFFFFFF), rate indicates maximum rate.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl2PIR specifies the total bandwidth limit, PIR, for priority level 2. This object overrides TIMETRA-QOS-MIB::tPortSchedPolicyLevelPIR for priority level 2 specified by TIMETRA-QOS-MIB::tPortSchedPolicyLevel. The value of 4294967295 (0xFFFFFFFF) indicates maximum rate. When the value of tmnxPortSchedOvrLvl2PIRHi along with the value of tmnxPortSchedOvrLvl2PIR is set to 4294967295 (0xFFFFFFFF), rate indicates maximum rate.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl2CIRHi specifies the upper 32 bits of the within-cir bandwidth limit for priority level 2. This object overrides TIMETRA-QOS-MIB::tPortSchedPolicyLevelCIR for priority level 2 specified by TIMETRA-QOS-MIB::tPortSchedPolicyLevel. This value should always be set along with tmnxPortSchedOvrLvl2CIR, otherwise an 'inconsistentValue' error is returned. When the value of tmnxPortSchedOvrLvl2CIRHi along with the value of tmnxPortSchedOvrLvl2CIR is set to 4294967295 (0xFFFFFFFF), rate indicates maximum rate.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl2CIR specifies the within-cir bandwidth limit for priority level 2. This object overrides TIMETRA-QOS-MIB::tPortSchedPolicyLevelCIR for priority level 2 specified by TIMETRA-QOS-MIB::tPortSchedPolicyLevel. The value of 4294967295 (0xFFFFFFFF) indicates maximum rate. When the value of tmnxPortSchedOvrLvl2CIRHi along with the value of tmnxPortSchedOvrLvl2CIR is set to 4294967295 (0xFFFFFFFF), rate indicates maximum rate.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl3PIRHi specifies the upper 32 bits of the total bandwidth limit, PIR, for priority level 3. This object overrides TIMETRA-QOS-MIB::tPortSchedPolicyLevelPIR for priority level 3 specified by TIMETRA-QOS-MIB::tPortSchedPolicyLevel. This value should always be set along with tmnxPortSchedOvrLvl3PIR, otherwise an 'inconsistentValue' error is returned. When the value of tmnxPortSchedOvrLvl3PIRHi along with the value of tmnxPortSchedOvrLvl3PIR is set to 4294967295 (0xFFFFFFFF), rate indicates maximum rate.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl3PIR specifies the total bandwidth limit, PIR, for priority level 3. This object overrides TIMETRA-QOS-MIB::tPortSchedPolicyLevelPIR for priority level 3 specified by TIMETRA-QOS-MIB::tPortSchedPolicyLevel. The value of 4294967295 (0xFFFFFFFF) indicates maximum rate. When the value of tmnxPortSchedOvrLvl3PIRHi along with the value of tmnxPortSchedOvrLvl3PIR is set to 4294967295 (0xFFFFFFFF), rate indicates maximum rate.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl3CIRHi specifies the upper 32 bits of the within-cir bandwidth limit for priority level 3. This object overrides TIMETRA-QOS-MIB::tPortSchedPolicyLevelCIR for priority level 3 specified by TIMETRA-QOS-MIB::tPortSchedPolicyLevel. This value should always be set along with tmnxPortSchedOvrLvl3CIR, otherwise an 'inconsistentValue' error is returned. When the value of tmnxPortSchedOvrLvl3CIRHi along with the value of tmnxPortSchedOvrLvl3CIR is set to 4294967295 (0xFFFFFFFF), rate indicates maximum rate.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl3CIR specifies the within-cir bandwidth limit for priority level 3. This object overrides TIMETRA-QOS-MIB::tPortSchedPolicyLevelCIR for priority level 3 specified by TIMETRA-QOS-MIB::tPortSchedPolicyLevel. The value of 4294967295 (0xFFFFFFFF) indicates maximum rate. When the value of tmnxPortSchedOvrLvl3CIRHi along with the value of tmnxPortSchedOvrLvl3CIR is set to 4294967295 (0xFFFFFFFF), rate indicates maximum rate.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl4PIRHi specifies the upper 32 bits of the total bandwidth limit, PIR, for priority level 4. This object overrides TIMETRA-QOS-MIB::tPortSchedPolicyLevelPIR for priority level 4 specified by TIMETRA-QOS-MIB::tPortSchedPolicyLevel. This value should always be set along with tmnxPortSchedOvrLvl4PIR, otherwise an 'inconsistentValue' error is returned. When the value of tmnxPortSchedOvrLvl4PIRHi along with the value of tmnxPortSchedOvrLvl4PIR is set to 4294967295 (0xFFFFFFFF), rate indicates maximum rate.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl4PIR specifies the total bandwidth limit, PIR, for priority level 4. This object overrides TIMETRA-QOS-MIB::tPortSchedPolicyLevelPIR for priority level 4 specified by TIMETRA-QOS-MIB::tPortSchedPolicyLevel. The value of 4294967295 (0xFFFFFFFF) indicates maximum rate. When the value of tmnxPortSchedOvrLvl4PIRHi along with the value of tmnxPortSchedOvrLvl4PIR is set to 4294967295 (0xFFFFFFFF), rate indicates maximum rate.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl4CIRHi specifies the upper 32 bits of the within-cir bandwidth limit for priority level 4. This object overrides TIMETRA-QOS-MIB::tPortSchedPolicyLevelCIR for priority level 4 specified by TIMETRA-QOS-MIB::tPortSchedPolicyLevel. This value should always be set along with tmnxPortSchedOvrLvl4CIR, otherwise an 'inconsistentValue' error is returned. When the value of tmnxPortSchedOvrLvl4CIRHi along with the value of tmnxPortSchedOvrLvl4CIR is set to 4294967295 (0xFFFFFFFF), rate indicates maximum rate.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl4CIR specifies the within-cir bandwidth limit for priority level 4. This object overrides TIMETRA-QOS-MIB::tPortSchedPolicyLevelCIR for priority level 4 specified by TIMETRA-QOS-MIB::tPortSchedPolicyLevel. The value of 4294967295 (0xFFFFFFFF) indicates maximum rate. When the value of tmnxPortSchedOvrLvl4CIRHi along with the value of tmnxPortSchedOvrLvl4CIR is set to 4294967295 (0xFFFFFFFF), rate indicates maximum rate.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl5PIRHi specifies the upper 32 bits of the total bandwidth limit, PIR, for priority level 5. This object overrides TIMETRA-QOS-MIB::tPortSchedPolicyLevelPIR for priority level 5 specified by TIMETRA-QOS-MIB::tPortSchedPolicyLevel. This value should always be set along with tmnxPortSchedOvrLvl5PIR, otherwise an 'inconsistentValue' error is returned. When the value of tmnxPortSchedOvrLvl5PIRHi along with the value of tmnxPortSchedOvrLvl5PIR is set to 4294967295 (0xFFFFFFFF), rate indicates maximum rate.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl5PIR specifies the total bandwidth limit, PIR, for priority level 5. This object overrides TIMETRA-QOS-MIB::tPortSchedPolicyLevelPIR for priority level 5 specified by TIMETRA-QOS-MIB::tPortSchedPolicyLevel. The value of 4294967295 (0xFFFFFFFF) indicates maximum rate. When the value of tmnxPortSchedOvrLvl5PIRHi along with the value of tmnxPortSchedOvrLvl5PIR is set to 4294967295 (0xFFFFFFFF), rate indicates maximum rate.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl5CIRHi specifies the upper 32 bits of the within-cir bandwidth limit for priority level 5. This object overrides TIMETRA-QOS-MIB::tPortSchedPolicyLevelCIR for priority level 5 specified by TIMETRA-QOS-MIB::tPortSchedPolicyLevel. This value should always be set along with tmnxPortSchedOvrLvl5CIR, otherwise an 'inconsistentValue' error is returned. When the value of tmnxPortSchedOvrLvl5CIRHi along with the value of tmnxPortSchedOvrLvl5CIR is set to 4294967295 (0xFFFFFFFF), rate indicates maximum rate.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl5CIR specifies the within-cir bandwidth limit for priority level 5. This object overrides TIMETRA-QOS-MIB::tPortSchedPolicyLevelCIR for priority level 5 specified by TIMETRA-QOS-MIB::tPortSchedPolicyLevel. The value of 4294967295 (0xFFFFFFFF) indicates maximum rate. When the value of tmnxPortSchedOvrLvl5CIRHi along with the value of tmnxPortSchedOvrLvl5CIR is set to 4294967295 (0xFFFFFFFF), rate indicates maximum rate.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl6PIRHi specifies the upper 32 bits of the total bandwidth limit, PIR, for priority level 6. This object overrides TIMETRA-QOS-MIB::tPortSchedPolicyLevelPIR for priority level 6 specified by TIMETRA-QOS-MIB::tPortSchedPolicyLevel. This value should always be set along with tmnxPortSchedOvrLvl6PIR, otherwise an 'inconsistentValue' error is returned. When the value of tmnxPortSchedOvrLvl6PIRHi along with the value of tmnxPortSchedOvrLvl6PIR is set to 4294967295 (0xFFFFFFFF), rate indicates maximum rate.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl6PIR specifies the total bandwidth limit, PIR, for priority level 6. This object overrides TIMETRA-QOS-MIB::tPortSchedPolicyLevelPIR for priority level 6 specified by TIMETRA-QOS-MIB::tPortSchedPolicyLevel. The value of 4294967295 (0xFFFFFFFF) indicates maximum rate. When the value of tmnxPortSchedOvrLvl6PIRHi along with the value of tmnxPortSchedOvrLvl6PIR is set to 4294967295 (0xFFFFFFFF), rate indicates maximum rate.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl6CIRHi specifies the upper 32 bits of the within-cir bandwidth limit for priority level 6. This object overrides TIMETRA-QOS-MIB::tPortSchedPolicyLevelCIR for priority level 6 specified by TIMETRA-QOS-MIB::tPortSchedPolicyLevel. This value should always be set along with tmnxPortSchedOvrLvl6CIR, otherwise an 'inconsistentValue' error is returned. When the value of tmnxPortSchedOvrLvl6CIRHi along with the value of tmnxPortSchedOvrLvl6CIR is set to 4294967295 (0xFFFFFFFF), rate indicates maximum rate.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl6CIR specifies the within-cir bandwidth limit for priority level 6. This object overrides TIMETRA-QOS-MIB::tPortSchedPolicyLevelCIR for priority level 6 specified by TIMETRA-QOS-MIB::tPortSchedPolicyLevel. The value of 4294967295 (0xFFFFFFFF) indicates maximum rate. When the value of tmnxPortSchedOvrLvl6CIRHi along with the value of tmnxPortSchedOvrLvl6CIR is set to 4294967295 (0xFFFFFFFF), rate indicates maximum rate.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl7PIRHi specifies the upper 32 bits of the total bandwidth limit, PIR, for priority level 7. This object overrides TIMETRA-QOS-MIB::tPortSchedPolicyLevelPIR for priority level 7 specified by TIMETRA-QOS-MIB::tPortSchedPolicyLevel. This value should always be set along with tmnxPortSchedOvrLvl7PIR, otherwise an 'inconsistentValue' error is returned. When the value of tmnxPortSchedOvrLvl7PIRHi along with the value of tmnxPortSchedOvrLvl7PIR is set to 4294967295 (0xFFFFFFFF), rate indicates maximum rate.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl7PIR specifies the total bandwidth limit, PIR, for priority level 7. This object overrides TIMETRA-QOS-MIB::tPortSchedPolicyLevelPIR for priority level 7 specified by TIMETRA-QOS-MIB::tPortSchedPolicyLevel. The value of 4294967295 (0xFFFFFFFF) indicates maximum rate. When the value of tmnxPortSchedOvrLvl7PIRHi along with the value of tmnxPortSchedOvrLvl7PIR is set to 4294967295 (0xFFFFFFFF), rate indicates maximum rate.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl7CIRHi specifies the upper 32 bits of the within-cir bandwidth limit for priority level 7. This object overrides TIMETRA-QOS-MIB::tPortSchedPolicyLevelCIR for priority level 7 specified by TIMETRA-QOS-MIB::tPortSchedPolicyLevel. This value should always be set along with tmnxPortSchedOvrLvl7CIR, otherwise an 'inconsistentValue' error is returned. When the value of tmnxPortSchedOvrLvl7CIRHi along with the value of tmnxPortSchedOvrLvl7CIR is set to 4294967295 (0xFFFFFFFF), rate indicates maximum rate.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl7CIR specifies the within-cir bandwidth limit for priority level 7. This object overrides TIMETRA-QOS-MIB::tPortSchedPolicyLevelCIR for priority level 7 specified by TIMETRA-QOS-MIB::tPortSchedPolicyLevel. The value of 4294967295 (0xFFFFFFFF) indicates maximum rate. When the value of tmnxPortSchedOvrLvl7CIRHi along with the value of tmnxPortSchedOvrLvl7CIR is set to 4294967295 (0xFFFFFFFF), rate indicates maximum rate.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl8PIRHi specifies the upper 32 bits of the total bandwidth limit, PIR, for priority level 8. This object overrides TIMETRA-QOS-MIB::tPortSchedPolicyLevelPIR for priority level 8 specified by TIMETRA-QOS-MIB::tPortSchedPolicyLevel. This value should always be set along with tmnxPortSchedOvrLvl8PIR, otherwise an 'inconsistentValue' error is returned. When the value of tmnxPortSchedOvrLvl8PIRHi along with the value of tmnxPortSchedOvrLvl8PIR is set to 4294967295 (0xFFFFFFFF), rate indicates maximum rate.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl8PIR specifies the total bandwidth limit, PIR, for priority level 8. This object overrides TIMETRA-QOS-MIB::tPortSchedPolicyLevelPIR for priority level 8 specified by TIMETRA-QOS-MIB::tPortSchedPolicyLevel. The value of 4294967295 (0xFFFFFFFF) indicates maximum rate. When the value of tmnxPortSchedOvrLvl8PIRHi along with the value of tmnxPortSchedOvrLvl8PIR is set to 4294967295 (0xFFFFFFFF), rate indicates maximum rate.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl8CIRHi specifies the upper 32 bits of the within-cir bandwidth limit for priority level 8. This object overrides TIMETRA-QOS-MIB::tPortSchedPolicyLevelCIR for priority level 8 specified by TIMETRA-QOS-MIB::tPortSchedPolicyLevel. This value should always be set along with tmnxPortSchedOvrLvl8CIR, otherwise an 'inconsistentValue' error is returned. When the value of tmnxPortSchedOvrLvl8CIRHi along with the value of tmnxPortSchedOvrLvl8CIR is set to 4294967295 (0xFFFFFFFF), rate indicates maximum rate.

OBJECT-TYPE

The value of tmnxPortSchedOvrLvl8CIR specifies the within-cir bandwidth limit for priority level 8. This object overrides TIMETRA-QOS-MIB::tPortSchedPolicyLevelCIR for priority level 8 specified by TIMETRA-QOS-MIB::tPortSchedPolicyLevel. The value of 4294967295 (0xFFFFFFFF) indicates maximum rate. When the value of tmnxPortSchedOvrLvl8CIRHi along with the value of tmnxPortSchedOvrLvl8CIR is set to 4294967295 (0xFFFFFFFF), rate indicates maximum rate.

OBJECT-TYPE

The tmnxBPGrpAssocTable has an entry for each Bundle Protection Group created on the system.

OBJECT-TYPE

Each row displays the relationship between a Bundle Protection group and its working and protection bundle.

OBJECT-TYPE

tmnxBPGrpAssocWorkingBundleID identifies the working bundle. A value of zero is given if no working bundle is associated with the given tmnxBundleBundleID.

OBJECT-TYPE

tmnxBPGrpAssocProtectBundleID identifies the protection bundle. A value of zero is given if no protection bundle is associated with the given tmnxBundleBundleID.

OBJECT-TYPE

tmnxBPGrpAssocActiveBundleID identifies the bundle that is considered the active bundle. This bundle contains the members that are part of the active aps port. A value of zero is given if no bundle is considered active.

OBJECT-TYPE

The tmnxBundleMlpppTable contains MLPPP specific data.

OBJECT-TYPE

Each row entry contains data on an MLPPP Bundle.

OBJECT-TYPE

tmnxBundleMlpppEndpointID specifies the Endpoint Discriminator identifier value within the specified tmnxBundleMlpppEndpointIDClass. The object tmnxPortAdminStatus must be set to 'outOfService' to change this value.

OBJECT-TYPE

tmnxBundleMlpppEndpointIDClass specifies the Link Control Protocol Endpoint Discriminator Class field type of the tmnxBundleMlpppEndpointID. The object tmnxPortAdminStatus must be set to 'outOfService' to change this value. Bundle DEFVAL Physical MLPPP Bundle ieee802dot1GlobalMacAddress (3) MLPPP Bundle Protection Group ipAddress (2)

OBJECT-TYPE

The value of tmnxBundleMlpppClassCount specifies whether Multiclass MLPPP is enabled on a bundle with a tmnxBundleType of 'mlppp' and when enabled what is the number of classes to be negotiated/supported over the MLPPP bundle. The value of 0 disables multiclass MLPPP including negotiation in the PPP protocol. All other values specify the number of classes to be supported on a given multiclass bundle and enable Multiclass MLPPP negotiation on that bundle. Non-zero values supported are platform/MDA specific. The value of tmnxBundleMlpppClassCount must be set to 0 and cannot be changed when LFI is enabled on the bundle (see tmnxBundleLFI object in tmnxBundleTable). The value of tmnxBundleMlpppClassCount may be modified only when tmnxBundleNumLinks is zero. To set the value of tmnxBundleMlpppClassCount to a value greater than 4, the long sequence format must be enabled on the bundle (see tmnxBundleShortSequence object in tmnxBundleTable). Changing the value of tmnxBundleMlpppClassCount resets the values of tmnxBundleMlpppIngQoSProfId and tmnxBundleMlpppEgrQoSProfId to their defaults

OBJECT-TYPE

tmnxBundleMlpppIngQoSProfId specifies ingress QoS profile to be used for the incoming traffic over this MLPPP bundle. The value of tmnxBundleMlpppIngQoSProfId may be modified only when the value of tmnxBundleNumLinks is 0. The value of tmnxBundleMlpppIngQoSProfId of 0 indicates a default QoS profile is used as applicable to a given hardware and the configured value of tmnxBundleMlpppClassCount.

OBJECT-TYPE

tmnxBundleMlpppEgrQoSProfId specifies egresss QoS profile to be used for the outgoing traffic over this MLPPP bundle. The value of tmnxBundleMlpppEgrQoSProfId may be modified only when tmnxBundleNumLinks is zero. The value of tmnxBundleMlpppEgrQoSProfId of 0 indicates a default profile is used as applicable to a given hardware and the configured value of tmnxBundleMlpppClassCount.

OBJECT-TYPE

tmnxBundleMlpppMagicNumber specifies whether or not the bundle will detect a loopback scenario on member links and take a looped back member links out of service. A value of 'enabled (1)' will detect loopbacks.

OBJECT-TYPE

tmnxBundleMlpppStatelessApsSwo specifies whether the bundle will perform a stateful or a stateless APS switchover. The value of tmnxBundleMlpppStatelessApsSwo must be set to 'disabled (2)' and cannot be changed for normal mlppp bundles. The value of tmnxBundleMlpppStatelessApsSwo may be changed for APS bundle protection groups. A stateless switchover implies that PPP is renegotiated on each member link after the switchover. PPP negotiations may take a few seconds to complete. A stateful switchover implies that after an APS switchover the PPP state of the bundle will be restored based on the bpgrp bundle state before the switchover. A value of 'enabled (1)' will configure stateless APS switchovers.

OBJECT-TYPE

The value of tmnxHsmdaPortSchOvrTblLastChngd indicates the sysUpTime at the time of the last modification of tmnxHsmdaPortSchOvrTable. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The tmnxHsmdaPortSchOvrTable has an entry for each port-level HSMDA scheduler override configured on this system.

OBJECT-TYPE

Each row represents a particular port-level HSMDA scheduler override. Entries are created and deleted by the user.

OBJECT-TYPE

The value of tmnxHsmdaPortSchOvrRowStatus is used for the creation and deletion of port-level HSMDA scheduler overrides. When the tmnxMDAAssignedType of the tmnxPortEntry indexed by the same indices of this table is a non-HSMDA MDA Type, creation will fail and return a 'noCreation' error.

OBJECT-TYPE

The value of tmnxHsmdaPortSchOvrLastChanged indicates the sysUpTime at the time of the last modification of this entry. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The value of tmnxHsmdaPortSchOvrMaxRate specifies the explicit maximum frame based bandwidth limit for this HSMDA port scheduler. A value of -2 indicates no override. This object overrides TIMETRA-QOS-MIB::tHsmdaSchedulerPlcyMaxRate.

OBJECT-TYPE

The value of tmnxHsmdaPortSchOvrGrp1Rate specifies the explicit maximum frame based bandwidth limit, in megabits per second, for group 1 for this HSMDA port scheduler. A value of -2 indicates no override. This object overrides TIMETRA-QOS-MIB::tHsmdaSchedulerPlcyGrp1Rate.

OBJECT-TYPE

The value of tmnxHsmdaPortSchOvrGrp2Rate specifies the explicit maximum frame based bandwidth limit, in megabits per second, for group 2 for this HSMDA port scheduler. A value of -2 indicates no override. This object overrides TIMETRA-QOS-MIB::tHsmdaSchedulerPlcyGrp2Rate.

OBJECT-TYPE

The value of tmnxHsmdaPortSchOvrClass1Rate specifies the explicit maximum frame based bandwidth limit, in megabits per second, for this HSMDA port scheduler policy level. A value of -2 indicates no override. This object overrides TIMETRA-QOS-MIB::tHsmdaSchedulerPlcyLvl1Rate.

OBJECT-TYPE

The value of tmnxHsmdaPortSchOvrClass1WtInGp specifies the weight the HSMDA port scheduler policy should apply to this policy level within the group it belongs to. The value of tmnxHsmdaPortSchOvrClass1WtInGp will only be used if this policy level has been assigned to a group by setting tHsmdaSchedulerPlcyLvl1GrpId to a non-zero value. A value of -2 indicates no override. This object overrides TIMETRA-QOS-MIB::tHsmdaSchedulerPlcyLvl1WgtInGrp.

OBJECT-TYPE

The value of tmnxHsmdaPortSchOvrClass2Rate specifies the explicit maximum frame based bandwidth limit, in megabits per second, for this HSMDA port scheduler policy level. A value of -2 indicates no override. This object overrides TIMETRA-QOS-MIB::tHsmdaSchedulerPlcyLvl2Rate.

OBJECT-TYPE

The value of tmnxHsmdaPortSchOvrClass2WtInGp specifies the weight the HSMDA port scheduler policy should apply to this policy level within the group it belongs to. The value of tmnxHsmdaPortSchOvrClass2WtInGp will only be used if this policy level has been assigned to a group by setting tHsmdaSchedulerPlcyLvl2GrpId to a non-zero value. A value of -2 indicates no override. This object overrides TIMETRA-QOS-MIB::tHsmdaSchedulerPlcyLvl2WgtInGrp.

OBJECT-TYPE

The value of tmnxHsmdaPortSchOvrClass3Rate specifies the explicit maximum frame based bandwidth limit, in megabits per second, for this HSMDA port scheduler policy level. A value of -2 indicates no override. This object overrides TIMETRA-QOS-MIB::tHsmdaSchedulerPlcyLvl3Rate.

OBJECT-TYPE

The value of tmnxHsmdaPortSchOvrClass3WtInGp specifies the weight the HSMDA port scheduler policy should apply to this policy level within the group it belongs to. The value of tmnxHsmdaPortSchOvrClass3WtInGp will only be used if this policy level has been assigned to a group by setting tHsmdaSchedulerPlcyLvl3GrpId to a non-zero value. A value of -2 indicates no override. This object overrides TIMETRA-QOS-MIB::tHsmdaSchedulerPlcyLvl3WgtInGrp.

OBJECT-TYPE

The value of tmnxHsmdaPortSchOvrClass4Rate specifies the explicit maximum frame based bandwidth limit, in megabits per second, for this HSMDA port scheduler policy level. A value of -2 indicates no override. This object overrides TIMETRA-QOS-MIB::tHsmdaSchedulerPlcyLvl4Rate.

OBJECT-TYPE

The value of tmnxHsmdaPortSchOvrClass4WtInGp specifies the weight the HSMDA port scheduler policy should apply to this policy level within the group it belongs to. The value of tmnxHsmdaPortSchOvrClass4WtInGp will only be used if this policy level has been assigned to a group by setting tHsmdaSchedulerPlcyLvl4GrpId to a non-zero value. A value of -2 indicates no override. This object overrides TIMETRA-QOS-MIB::tHsmdaSchedulerPlcyLvl4WgtInGrp.

OBJECT-TYPE

The value of tmnxHsmdaPortSchOvrClass5Rate specifies the explicit maximum frame based bandwidth limit, in megabits per second, for this HSMDA port scheduler policy level. A value of -2 indicates no override. This object overrides TIMETRA-QOS-MIB::tHsmdaSchedulerPlcyLvl5Rate.

OBJECT-TYPE

The value of tmnxHsmdaPortSchOvrClass5WtInGp specifies the weight the HSMDA port scheduler policy should apply to this policy level within the group it belongs to. The value of tmnxHsmdaPortSchOvrClass5WtInGp will only be used if this policy level has been assigned to a group by setting tHsmdaSchedulerPlcyLvl5GrpId to a non-zero value. A value of -2 indicates no override. This object overrides TIMETRA-QOS-MIB::tHsmdaSchedulerPlcyLvl5WgtInGrp.

OBJECT-TYPE

The value of tmnxHsmdaPortSchOvrClass6Rate specifies the explicit maximum frame based bandwidth limit, in megabits per second, for this HSMDA port scheduler policy level. A value of -2 indicates no override. This object overrides TIMETRA-QOS-MIB::tHsmdaSchedulerPlcyLvl6Rate.

OBJECT-TYPE

The value of tmnxHsmdaPortSchOvrClass6WtInGp specifies the weight the HSMDA port scheduler policy should apply to this policy level within the group it belongs to. The value of tmnxHsmdaPortSchOvrClass6WtInGp will only be used if this policy level has been assigned to a group by setting tHsmdaSchedulerPlcyLvl6GrpId to a non-zero value. A value of -2 indicates no override. This object overrides TIMETRA-QOS-MIB::tHsmdaSchedulerPlcyLvl6WgtInGrp.

OBJECT-TYPE

The value of tmnxHsmdaPortSchOvrClass7Rate specifies the explicit maximum frame based bandwidth limit, in megabits per second, for this HSMDA port scheduler policy level. A value of -2 indicates no override. This object overrides TIMETRA-QOS-MIB::tHsmdaSchedulerPlcyLvl7Rate.

OBJECT-TYPE

The value of tmnxHsmdaPortSchOvrClass7WtInGp specifies the weight the HSMDA port scheduler policy should apply to this policy level within the group it belongs to. The value of tmnxHsmdaPortSchOvrClass7WtInGp will only be used if this policy level has been assigned to a group by setting tHsmdaSchedulerPlcyLvl7GrpId to a non-zero value. A value of -2 indicates no override. This object overrides TIMETRA-QOS-MIB::tHsmdaSchedulerPlcyLvl7WgtInGrp.

OBJECT-TYPE

The value of tmnxHsmdaPortSchOvrClass8Rate specifies the explicit maximum frame based bandwidth limit, in megabits per second, for this HSMDA port scheduler policy level. A value of -2 indicates no override. This object overrides TIMETRA-QOS-MIB::tHsmdaSchedulerPlcyLvl8Rate.

OBJECT-TYPE

The value of tmnxHsmdaPortSchOvrClass8WtInGp specifies the weight the HSMDA port scheduler policy should apply to this policy level within the group it belongs to. The value of tmnxHsmdaPortSchOvrClass8WtInGp will only be used if this policy level has been assigned to a group by setting tHsmdaSchedulerPlcyLvl8GrpId to a non-zero value. A value of -2 indicates no override. This object overrides TIMETRA-QOS-MIB::tHsmdaSchedulerPlcyLvl8WgtInGrp.

OBJECT-TYPE

The value of tmnxPortEgrShaperTblLastChanged indicates the sysUpTime at the time of the last modification of tmnxPortEgrShaperTable. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value. This object is obsoleted in 10.0 Release.

OBJECT-TYPE

The tmnxPortEgrShaperTable has an entry for each port-level egress secondary shaper configured on this system. This table is obsoleted in 10.0 Release.

OBJECT-TYPE

Each row represents a particular port-level egress secondary shaper. Entries are created and deleted by the user.

OBJECT-TYPE

The port egress shaper named is used an index to the table entry.

OBJECT-TYPE

The value of tmnxPortEgrShaperRowStatus is used for the creation and deletion of entries in the tmnxPortEgrShaperTable.

OBJECT-TYPE

The value of tmnxPortEgrShaperLastChanged indicates the sysUpTime at the time of the last modification of this entry. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The value of tmnxPortEgrShaperRate specifies the explicit maximum frame based bandwidth limit, in megabits per second, of this egress port secondary shaper policy.

OBJECT-TYPE

The tmnxDigitalDiagMonitorTable has an entry for each SFF in the system that supports Digital Diagnostic Monitoring (DDM). The table is indexed by TmnxPortID. Each row in this table is dynamically added and removed internally by the system based on the presence or absence of DDM capable SFF components.

OBJECT-TYPE

Each row represents a particular SFF that supports Digital Diagnostic Monitoring. Entries are created and deleted internally by the system.

OBJECT-TYPE

The value of tmnxDDMTemperature indicates the current temperature of the SFF in 1/256th degrees Celsius. If the SFF is externally calibrated, the objects tmnxDDMExtCalTemperatureSlope and tmnxDDMExtCalTemperatureOffset affect the temperature calculation. The formula for translating between the value of tmnxDDMTemperature and degrees Celsius is: Internally Calibrated only: tmnxDDMTemperature / 256 Externally Calibrated: (tmnxDDMTemperature * (tmnxDDMExtCalTemperatureSlope / 256) + tmnxDDMExtCalTemperatureOffset) / 256 For example (internally calibrated SFF): The SNMP value 5734 is 22.4 degrees Celsius.

OBJECT-TYPE

The value of tmnxDDMTempLowWarning indicates the temperature of the SFF that triggers a low-warning. See description of tmnxDDMTemperature for translating to degrees Celsius.

OBJECT-TYPE

The value of tmnxDDMTempLowAlarm indicates the temperature of the SFF that triggers a low-alarm. See description of tmnxDDMTemperature for translating to degrees Celsius.

OBJECT-TYPE

The value of tmnxDDMTempHiWarning indicates the temperature of the SFF that triggers a hi-warning. See description of tmnxDDMTemperature for translating to degrees Celsius.

OBJECT-TYPE

The value of tmnxDDMTempHiAlarm indicates the temperature of the SFF that triggers a hi-alarm. See description of tmnxDDMTemperature for translating to degrees Celsius.

OBJECT-TYPE

The value of tmnxDDMSupplyVoltage indicates the current supply voltage of the SFF. For 100G MSA Transponder, the supply voltage is in millivolts (mV). For all other types the voltage is in deci-millivolts (1/10th of a millivolt or 100 microvolt units). If the SFF is externally calibrated, the objects tmnxDDMExtCalVoltageSlope and tmnxDDMExtCalVoltageOffset affect the voltage calculation. The formula for translating between the value of tmnxDDMSupplyVoltage and Voltage is: Internally Calibrated only: tmnxDDMSupplyVoltage * conversion_factor Externally Calibrated: (tmnxDDMSupplyVoltage * (tmnxDDMExtCalVoltageSlope / 256) + tmnxDDMExtCalVoltageOffset) * conversion_factor where conversion_factor is 1/1000 for 100G MSA transponders and 1/10000 for all the others. For example (internally calibrated SFF): 1. For 100G MSA transponders, the SNMP value 32851 is 32.851 Volts (V). 2. For all others, the SNMP value 32851 is 3.2851 Volts (V).

OBJECT-TYPE

The value of tmnxDDMSupplyVoltageLowWarning indicates the supply voltage of the SFF that trigger a low-warning. See description of tmnxDDMSupplyVoltage for translating to Volts (V).

OBJECT-TYPE

The value of tmnxDDMSupplyVoltageLowAlarm indicates the supply voltage of the SFF that triggers a low-alarm. See description of tmnxDDMSupplyVoltage for translating to Volts (V).

OBJECT-TYPE

The value of tmnxDDMSupplyVoltageHiWarning indicates the supply voltage of the SFF that triggers a hi-warning. See description of tmnxDDMSupplyVoltage for translating to Volts (V).

OBJECT-TYPE

The value of tmnxDDMSupplyVoltageHiAlarm indicates the supply voltage of the SFF that triggers a hi-alarm. See description of tmnxDDMSupplyVoltage for translating to Volts (V).

OBJECT-TYPE

The value of tmnxDDMTxBiasCurrent indicates the current Transmit Bias Current of the SFF in 1/500 milliamperes (mA). If the SFF is externally calibrated, the objects tmnxDDMExtCalTxLaserBiasSlope and tmnxDDMExtCalTxLaserBiasOffset affect the ampere calculation. The formula for translating between the value of tmnxDDMTxBiasCurrent and milliamperes is: Internally Calibrated only: tmnxDDMTxBiasCurrent / 500 Externally Calibrated: (tmnxDDMTxBiasCurrent * (tmnxDDMExtCalTxLaserBiasSlope / 256) + tmnxDDMExtCalTxLaserBiasOffset) / 500 For example (internally calibrated SFF): The SNMP value 2565 is 5.1 milliamperes (mA).

OBJECT-TYPE

The value of tmnxDDMTxBiasCurrentLowWarning indicates the Transmit Bias Current of the SFF that triggers a low-warning. See description of tmnxDDMTxBiasCurrent for translating to milliamperes (mA).

OBJECT-TYPE

The value of tmnxDDMTxBiasCurrentLowAlarm indicates the Transmit Bias Current of the SFF that triggers a low-alarm. See description of tmnxDDMTxBiasCurrent for translating to milliamperes (mA).

OBJECT-TYPE

The value of tmnxDDMTxBiasCurrentHiWarning indicates the Transmit Bias Current of the SFF that triggers a hi-warning. See description of tmnxDDMTxBiasCurrent for translating to milliamperes (mA).

OBJECT-TYPE

The value of tmnxDDMTxBiasCurrentHiAlarm indicates the Transmit Bias Current of the SFF that triggers a hi-alarm. See description of tmnxDDMTxBiasCurrent for translating to milliamperes (mA).

OBJECT-TYPE

The value of tmnxDDMTxOutputPower indicates the current Output Power of the SFF in one tenths of a microwatt (uW). If the SFF is externally calibrated, the objects tmnxDDMExtCalTxPowerSlope and tmnxDDMExtCalTxPowerOffset affect the output power calculation. For example (internally calibrated SFF): Using the SNMP value of 790, and using units of tenths of microwatt, 790 becomes 79 microwatts or 0.079 milliwatts. Converting to dBm: 10 x log10(0.079) = -11.0 dBm

OBJECT-TYPE

The value of tmnxDDMTxOutputPowerLowWarning indicates the Output Power of the SFF in one tenths of a microwatt (uW) that triggers a low-warning.

OBJECT-TYPE

The value of tmnxDDMTxOutputPowerLowAlarm indicates the Output Power of the SFF in one tenths of a microwatt (uW) that triggers a low-alarm.

OBJECT-TYPE

The value of tmnxDDMTxOutputPowerHiWarning indicates the Output Power of the SFF in one tenths of a microwatt (uW) that triggers a hi-warning.

OBJECT-TYPE

The value of tmnxDDMTxOutputPowerHiAlarm indicates the Output Power of the SFF in one tenths of a microwatt (uW) that triggers a hi-alarm.

OBJECT-TYPE

The value of tmnxDDMRxOpticalPower indicates the current Received Optical Power of the SFF in one tenths of a microwatt (uW). If the SFF is externally calibrated, the objects tmnxDDMExtCalRxPower4, tmnxDDMExtCalRxPower3, tmnxDDMExtCalRxPower2, tmnxDDMExtCalRxPower1 and tmnxDDMExtCalRxPower0 affect the output power calculation. For example (internally calibrated SFF): Using the SNMP value of 790, and using units of tenths of microwatt, 790 becomes 79 microwatts or 0.079 milliwatts. Converting to dBm: 10 x log10(0.079) = -11.0 dBm

OBJECT-TYPE

The value of tmnxDDMRxOpticalPowerLowWarning indicates the Received Optical Power of the SFF in one tenths of a microwatt (uW) that triggers a low-warning.

OBJECT-TYPE

The value of tmnxDDMRxOpticalPowerLowAlarm indicates the Received Optical Power of the SFF in one tenths of a microwatt (uW) that triggers a low-alarm.

OBJECT-TYPE

The value of tmnxDDMRxOpticalPowerHiWarning indicates the Received Optical Power of the SFF in one tenths of a microwatt (uW) that triggers a hi-warning.

OBJECT-TYPE

The value of tmnxDDMRxOpticalPowerHiAlarm indicates the Received Optical Power of the SFF in one tenths of a microwatt (uW) that triggers a hi-alarm.

OBJECT-TYPE

The value of tmnxDDMRxOpticalPowerType indicates whether the tmnxDDMRxOpticalPower was taken as an average, or as an Optical Modulation Amplitude (OMA).

OBJECT-TYPE

The value of tmnxDDMAux1 indicates the Manufacturer specific Auxiliary 1 information of the XFP.

OBJECT-TYPE

The value of tmnxDDMAux1LowWarning indicates the Manufacturer specific Auxiliary 1 low-warning threshold for the XFP.

OBJECT-TYPE

The value of tmnxDDMAux1LowAlarm indicates the Manufacturer specific Auxiliary 1 low-alarm threshold for the XFP.

OBJECT-TYPE

The value of tmnxDDMAux1HiWarning indicates the Manufacturer specific Auxiliary 1 hi-warning threshold for the XFP.

OBJECT-TYPE

The value of tmnxDDMAux1HiAlarm indicates the Manufacturer specific Auxiliary 1 hi-alarm threshold for the XFP.

OBJECT-TYPE

The value of tmnxDDMAux1Type indicates the measurement type of the Manufacturer specific Auxiliary 1 information of the XFP: none (0) - not specified. adp-bias-voltage (1) - LSB is 10mV. reserved-2 (2) - reserved for future use. tec-current (3) - LSB is 100uA. laser-temp (4) - degrees Celsius(C). laser-wavelength (5) - LSB is 0.05 nm. voltage-50 (6) - 5.0 supply voltage, LSB=100uV. voltage-33 (7) - 3.3 supply voltage, LSB=100uV. voltage-18 (8) - 1.8 supply voltage, LSB=100uV, voltage-52 (9) - -5.2 supply voltage, LSB=100uV. current-50 (10) - 5.0V supply current, LSB=100uA. reserved-11 (11) - reserved for future use. reserved-12 (12) - reserved for future use. current-33 (13) - 3.3V supply current, LSB=100uA. current-18 (14) - 1.8V supply current, LSB=100uA. current-52 (15) - -5.2V supply current, LSB=100uA.

OBJECT-TYPE

The value of tmnxDDMAux2 indicates the Manufacturer specific Auxiliary 2 information of the SFF.

OBJECT-TYPE

The value of tmnxDDMAux2LowWarning indicates the Manufacturer specific Auxiliary 2 low-warning threshold for the XFP.

OBJECT-TYPE

The value of tmnxDDMAux2LowAlarm indicates the Manufacturer specific Auxiliary 2 low-alarm threshold for the XFP.

OBJECT-TYPE

The value of tmnxDDMAux2HiWarning indicates the Manufacturer specific Auxiliary 2 hi-warning threshold for the XFP.

OBJECT-TYPE

The value of tmnxDDMAux2HiAlarm indicates the Manufacturer specific Auxiliary 2 hi-alarm threshold for the XFP.

OBJECT-TYPE

The value of tmnxDDMAux2Type indicates the measurement type of the Manufacturer specific Auxiliary 2 information of the XFP: none (0) - not specified. adp-bias-voltage (1) - LSB is 10mV. reserved-2 (2) - reserved for future use. tec-current (3) - LSB is 100uA. laser-temp (4) - degrees Celsius(C). laser-wavelength (5) - LSB is 0.05 nm. voltage-50 (6) - 5.0 supply voltage, LSB=100uV. voltage-33 (7) - 3.3 supply voltage, LSB=100uV. voltage-18 (8) - 1.8 supply voltage, LSB=100uV, voltage-52 (9) - -5.2 supply voltage, LSB=100uV. current-50 (10) - 5.0V supply current, LSB=100uA. reserved-11 (11) - reserved for future use. reserved-12 (12) - reserved for future use. current-33 (13) - 3.3V supply current, LSB=100uA. current-18 (14) - 1.8V supply current, LSB=100uA. current-52 (15) - -5.2V supply current, LSB=100uA.

OBJECT-TYPE

The value of tmnxDDMFailedThresholds indicates which objects of the monitored SFF is in a failed or cleared threshold state. A set bit indicates that the specified threshold has been exceeded.

OBJECT-TYPE

The value of tmnxDDMExternallyCalibrated indicates whether the SFF was externally calibrated (true) or internally calibrated (false).

OBJECT-TYPE

The value of tmnxDDMExtCalRxPower4 indicates the Rx_PWR(4) value as specified in Table 3.16 in the SFF Committee Standard's document SFF-8472 Rev 10.2.

OBJECT-TYPE

The value of tmnxDDMExtCalRxPower3 indicates the Rx_PWR(3) value as specified in Table 3.16 in the SFF Committee Standard's document SFF-8462 Rev 10.2.

OBJECT-TYPE

The value of tmnxDDMExtCalRxPower2 indicates the Rx_PWR(2) value as specified in Table 3.16 in the SFF Committee Standard's document SFF-8472 Rev 10.2.

OBJECT-TYPE

The value of tmnxDDMExtCalRxPower1 indicates the Rx_PWR(1) value as specified in Table 3.16 in the SFF Committee Standard's document SFF-8472 Rev 10.2.

OBJECT-TYPE

The value of tmnxDDMExtCalRxPower0 indicates the Rx_PWR(0) value as specified in Table 3.16 in the SFF Committee Standard's document SFF-8472 Rev 10.2.

OBJECT-TYPE

The value of tmnxDDMExtCalTxLaserBiasSlope indicates the Tx_l(Slope) value as specified in Table 3.16 in the SFF Committee Standard's document SFF-8472 Rev 10.2.

OBJECT-TYPE

The value of tmnxDDMExtCalTxLaserBiasOffset indicates the Tx_l(Offset) value as specified in Table 3.16 in the SFF Committee Standard's document SFF-8472 Rev 10.2.

OBJECT-TYPE

The value of tmnxDDMExtCalTxPowerSlope indicates the Tx_PWR(Slope) value as specified in Table 3.16 in the SFF Committee Standard's document SFF-8472 Rev 10.2.

OBJECT-TYPE

The value of tmnxDDMExtCalTxPowerOffset indicates the Tx_PWR(Offset) value as specified in Table 3.16 in the SFF Committee Standard's document SFF-8472 Rev 10.2.

OBJECT-TYPE

The value of tmnxDDMExtCalTemperatureSlope indicates the T(Slope) value as specified in Table 3.16 in the SFF Committee Standard's document SFF-8472 Rev 10.2.

OBJECT-TYPE

The value of tmnxDDMExtCalTemperatureOffset indicates the T(Offset) value as specified in Table 3.16 in the SFF Committee Standard's document SFF-8472 Rev 10.2.

OBJECT-TYPE

The value of tmnxDDMExtCalVoltageSlope indicates the V(Slope) value as specified in Table 3.16 in the SFF Committee Standard's document SFF-8472 Rev 10.2.

OBJECT-TYPE

The value of tmnxDDMExtCalVoltageOffset indicates the V(Slope) value as specified in Table 3.16 in the SFF Committee Standard's document SFF-8472 Rev 10.2.

OBJECT-TYPE

The value of tPortAccIngQGrpTableLastChgd indicates the timestamp of last change to the tPortAccIngQGrpTable.

OBJECT-TYPE

The value of tPortAccIngQGrpTable defines access Ingress Queue Group Table for providing, via SNMP, the capability of defining the port specific queue groups from the queue-groups existing in the TIMETRA-QOS-MIB::tQosIngQGroupTable.

OBJECT-TYPE

The value of tPortAccIngQGrpEntry defines an entry in the tPortAccIngQGrpTable. Entries are created/deleted in this table by SNMP sets to tPortAccIngQGrpRowStatus.

OBJECT-TYPE

The value of tPortAccIngQGrpName defines the port Ingress Queue Group name. It uniquely identifies a port ingress queue group in the managed system.

OBJECT-TYPE

The value of tPortAccIngQGrpRowStatus allows entries to be created and deleted in the tPortAccIngQGrpTable. The creation of an entry in this table will succeed only if the queue-group being created exists in TIMETRA-QOS-MIB::tQosIngQGroupTable.

OBJECT-TYPE

The value of tPortAccIngQGrpLastChgd indicates the value of sysUpTime when the queue entry was last modified.

OBJECT-TYPE

The value of tPortAccIngQGrpSchedPol specifies the name of the scheduler policy to be used with this port ingress queue-group.

OBJECT-TYPE

The value of tPortAccIngQGrpAcctgPolId specifies the accounting-policy to be used with this port ingress queue-group. A non-zero value indicates the tmnxLogApPolicyId index identifying the policy entry in the tmnxLogApTable from the TIMETRA-LOG-MIB which is associated with this queue-group. The value zero indicates that the agent should use the default accounting policy, if one exists.

OBJECT-TYPE

The value of tPortAccIngQGrpCollectStats specifies whether statistics should be collected on this port ingress queue-group.

OBJECT-TYPE

The value of tPortAccIngQGrpDescr specifies the description for this port queue-group.

OBJECT-TYPE

The value of tPortAccIngQOverTableLastChgd indicates the timestamp of last change to the tPortAccIngQOverTable.

OBJECT-TYPE

The tPortAccIngQOverTable has an entry for each access port queue override configured on this system.

OBJECT-TYPE

Each row represents a particular port queue override. Entries are created and deleted by the user.

OBJECT-TYPE

The value of tPortAccIngQOverQueue specifies the queue ID which is used as the fourth index to the table entry.

OBJECT-TYPE

The value of tPortAccIngQOverRowStatus is used for the creation and deletion of port queue overrides. Row creation will fail if there is no entry in the TIMETRA-QOS-MIB::tQosIngQueueTable with the same index values as the last two indices of this table (tPortAccIngQGrpName.tPortAccIngQOverQueue).

OBJECT-TYPE

The value of tPortAccIngQOverLastChanged indicates the value of sysUpTime at the time of the most recent management change to this row.

OBJECT-TYPE

The value of tPortAccIngQOverCBS specifies the amount of reserved buffer space for the queue.

OBJECT-TYPE

The value of tPortAccIngQOverMBS specifies the maximum amount of buffer space allowed for the queue. This object is replaced with tPortAccIngQOverMBSBytes object.

OBJECT-TYPE

The value of tPortAccIngQOverHiPrioOnly specifies the percentage of buffer space for the queue, used exclusively by high priority packets. This object is obsoleted in 15.0 release and has been replaced with tPortAccIngQDrpTailLowReductnMbs object.

OBJECT-TYPE

The value of tPortAccIngQOverAdminPIR specifies the administrative PIR specified by the user.

OBJECT-TYPE

The value of tPortAccIngQOverAdminCIR specifies the administrative CIR specified by the user.

OBJECT-TYPE

The value of tPortAccIngQOverPIRAdaptation specifies the adaptation rule to be used while computing the operational PIR value. The adaptation rule specifies the rules to compute the operational values while maintaining minimum offset.

OBJECT-TYPE

The value of tPortAccIngQOverCIRAdaptation specifies the adaptation rule to be used while computing the operational CIR value. The adaptation rule specifies the rules to compute the operational values while maintaining minimum offset.

OBJECT-TYPE

The value of tPortAccIngQOverMBSBytes specifies the maximum amount of buffer space allowed for the queue.

OBJECT-TYPE

The value of tPortAccIngQOverMonitorDepth specifies whether to enable queue depth monitoring for this specified queue.

OBJECT-TYPE

The value of tPortAccIngQDrpTailLowReductnMbs specifies the percentage at which low drop tail is being reduced from the MBS specified by tPortAccIngQOverMBSBytes.

OBJECT-TYPE

The value of tPortAccEgrQGrpTableLastChgd indicates the timestamp of last change to the tPortAccEgrQGrpTable.

OBJECT-TYPE

The value of tPortAccEgrQGrpTable defines access Egress Queue Group Table for providing, via SNMP, the capability of defining the port specific queue groups from the queue-groups existing in the TIMETRA-QOS-MIB::tQosEgrQGroupTable.

OBJECT-TYPE

The value of tPortAccEgrQGrpEntry defines an entry in the tPortAccEgrQGrpTable. Entries are created/deleted in this table by SNMP sets to tPortAccEgrQGrpRowStatus.

OBJECT-TYPE

The value of tPortAccEgrQGrpName defines the port Egress Queue Group name. It, along with tPortAccEgrQGrpInstanceId, uniquely identifies a port egress queue group in the managed system.

OBJECT-TYPE

The value of tPortAccEgrQGrpRowStatus allows entries to be created and deleted in the tPortAccEgrQGrpTable. The creation of an entry in this table will succeed only if the queue-group being created exist in TIMETRA-QOS-MIB::tQosEgrQGroupTable.

OBJECT-TYPE

The value of tPortAccEgrQGrpLastChgd indicates the value of sysUpTime when the queue entry was last modified.

OBJECT-TYPE

The value of tPortAccEgrQGrpSchedPol specifies the name of the scheduler policy to be used with this port egress queue-group.

OBJECT-TYPE

The value of tPortAccEgrQGrpAggRateLimit specifies the maximum total rate of all egress queues in this queue-group. The value '-1' means that there is no limit. This object is obsoleted in 13.0 release and replaced by tPortAccEgrQGrpAggRateLmt.

OBJECT-TYPE

The value of tPortAccEgrQGrpAcctgPolId specifies the accounting-policy to be used with this port egress queue-group. A non-zero value indicates the tmnxLogApPolicyId index identifying the policy entry in the tmnxLogApTable from the TIMETRA-LOG-MIB which is associated with this queue-group. The value zero indicates that the agent should use the default accounting policy, if one exists.

OBJECT-TYPE

The value of tPortAccEgrQGrpCollectStats specifies whether statistics should be collected on this port egress queue-group.

OBJECT-TYPE

The value of tPortAccEgrQGrpFrameBaseActg specifies whether to use frame-based accounting for this port egress queue-group. If the value is 'false', the default packet-based accounting method will be used.

OBJECT-TYPE

The value of tPortAccEgrQGrpDescr specifies the description for this port queue-group.

OBJECT-TYPE

The value of tPortAccEgrQGrpInstanceId defines the unique instance of the port access egress Queue Group. It, along with tPortAccEgrQGrpName, uniquely identifies a port access egress queue group in the managed system.

OBJECT-TYPE

The value of tPortAccEgrQGrpHsmdaShaperOvr specifies the name of the secondary shaper for this queue-group instance. This value must correspond to an entry in the tmnxPortEgrShaperTable. If an empty string is specified, default secondary shaper will be used.

OBJECT-TYPE

The value of tPortAccEgrQGrpHsmdaPktOffOvr specifies the adjustment made to the size of each packet for HSMDA queue accounting for this queue-group instance.

OBJECT-TYPE

The value of tPortAccEgrQGrpHsmdaWrrPolicyOvr specifies the egress hsmda weighted round-robin policy override for this queue group instance. When no policy is given, the hsmda weighted round-robin policy specified in the queue-group template is honored. When a valid policy is given, it overrides the hsmda weighted round-robin policy given in the egress queue group template.

OBJECT-TYPE

The value of tPortAccEgrQGrpAggRateLUB specifies whether to limit the unused bandwidth and allow a tighter control in allocation of bandwidth by HQos. When the value of tPortAccEgrQGrpAggRateLUB is set to 'true', HQos algorithm distributes any unused aggregate bandwidth between queues operating below their fair share rates. This allows a simplified aggregate rate protection while allocating bandwidth by HQos scheduling algorithm.

OBJECT-TYPE

The value of tPortAccEgrQGrpAggRateLmt specifies the maximum total rate of all egress queues in this queue-group. The The value of 4294967295 (0xFFFFFFFF) means that there is no limit.

OBJECT-TYPE

The value of tPortAccEgrQGrpHsTurboQueues specifies whether to enable resource allocation of fast HS Queue-Group queues (set of 8 queues) which are capable of handling higher speeds. The value of this object has no effect on non-HS port.

OBJECT-TYPE

The value of tPortAccEgrQOverTableLastChgd indicates the timestamp of last change to the tPortAccEgrQOverTable.

OBJECT-TYPE

The tPortAccEgrQOverTable has an entry for each access port queue override configured on this system.

OBJECT-TYPE

Each row represents a particular port queue override. Entries are created and deleted by the user.

OBJECT-TYPE

The value of tPortAccEgrQOverQueue specifies the queue ID which is used as the fourth index to the table entry.

OBJECT-TYPE

The value of tPortAccEgrQOverRowStatus is used for the creation and deletion of port queue overrides. Row creation will fail if there is no entry in the TIMETRA-QOS-MIB::tQosEgrQueueTable with the same index values as the last two indices of this table (tPortAccEgrQGrpName.tPortAccEgrQOverQueue).

OBJECT-TYPE

The value of tPortAccEgrQOverLastChanged indicates the value of sysUpTime at the time of the most recent management change to this row.

OBJECT-TYPE

The value of tPortAccEgrQOverCBS specifies the amount of reserved buffer space for the queue.

OBJECT-TYPE

The value of tPortAccEgrQOverMBS specifies the maximum amount of buffer space allowed for the queue. This object is replaced with tPortAccEgrQOverMBSBytes object.

OBJECT-TYPE

The value of tPortAccEgrQOverHiPrioOnly specifies the percentage of buffer space for the queue, used exclusively by high priority packets. This object is obsoleted in 15.0 release and has been replaced with tPortAccEgrQDrpTailLowReductnMbs object.

OBJECT-TYPE

The value of tPortAccEgrQOverAdminPIR specifies the administrative PIR specified by the user. An 'inconsistentValue' error is returned if tPortAccEgrQOverAdminPIR is set to non-default value when the object tPortAccEgrQOverRateType is set to 'percent'.

OBJECT-TYPE

The value of tPortAccEgrQOverAdminCIR specifies the administrative CIR specified by the user. An 'inconsistentValue' error is returned if tPortAccEgrQOverAdminCIR is set to non-default value when the object tPortAccEgrQOverRateType is set to 'percent'.

OBJECT-TYPE

The value of tPortAccEgrQOverPIRAdaptation specifies the adaptation rule to be used while computing the operational PIR value. The adaptation rule specifies the rules to compute the operational values while maintaining minimum offset.

OBJECT-TYPE

The value of tPortAccEgrQOverCIRAdaptation specifies the adaptation rule to be used while computing the operational CIR value. The adaptation rule specifies the rules to compute the operational values while maintaining minimum offset.

OBJECT-TYPE

The value of tPortAccEgrQOverMBSBytes specifies the maximum amount of buffer space allowed for the queue.

OBJECT-TYPE

The value of tPortAccEgrQOverAdminPIRPercent specifies the administrative PIR percentage, in centipercent. An 'inconsistentValue' error is returned if tPortAccEgrQOverAdminPIRPercent is set to non-default value when the object tPortAccEgrQOverRateType is set to 'kbps'.

OBJECT-TYPE

The value of tPortAccEgrQOverAdminCIRPercent specifies the administrative CIR percentage, in centipercent. An 'inconsistentValue' error is returned if tPortAccEgrQOverAdminCIRPercent is set to non-default value when the object tPortAccEgrQOverRateType is set to 'kbps'.

OBJECT-TYPE

The value of tPortAccEgrQOverRateType specifies the type of Egress queue rate. When the value of the object is set to 'kbps', the egresss queue rates are specified in kbps. The objects tPortAccEgrQOverAdminPIRPercent and tPortAccEgrQOverAdminCIRPercent will be set to their default values. When the value of the object is set to 'percent', the egress queue rates are specified in percentage. The objects tPortAccEgrQOverAdminPIR and tPortAccEgrQOverAdminCIR will be set to their default values.

OBJECT-TYPE

The value of tPortAccEgrQOverWeight specifies the weight that needs to be used by the scheduler to which this queue would be feeding.

OBJECT-TYPE

The value of tPortAccEgrQOverCIRWeight specifies the weight that should be assigned to this queue by the parent scheduler among all the entities feeding into the parent, when the traffic is conforming to the committed rate. A value of '0' specifies that the queue will not receive bandwidth for the 'within-cir' pass on its parent scheduler.

OBJECT-TYPE

The value of tPortAccEgrQOverMonitorDepth specifies whether to enable queue depth monitoring for this specified queue.

OBJECT-TYPE

The value of tPortAccEgrQDrpTailLowReductnMbs specifies the percentage at which low drop tail is being reduced from the MBS specified by tPortAccEgrQOverMBSBytes.

OBJECT-TYPE

The value of tPortAccEgrQOverBurstLimit specifies the the explicit shaping burst size of a queue.

OBJECT-TYPE

The value of tPortNetEgrQGrpTableLastChgd indicates the timestamp of last change to the tPortNetEgrQGrpTable.

OBJECT-TYPE

The value of tPortNetEgrQGrpTable defines network Egress Queue Group Table for providing, via SNMP, the capability of defining the port specific queue groups from the queue-groups existing in the TIMETRA-QOS-MIB::tQosEgrQGroupTable.

OBJECT-TYPE

The value of tPortNetEgrQGrpEntry defines an entry in the tPortNetEgrQGrpTable. Entries are created/deleted in this table by SNMP sets to tPortNetEgrQGrpRowStatus.

OBJECT-TYPE

The value of tPortNetEgrQGrpName defines the port Egress Queue Group name. It, along with tPortNetEgrQGrpInstanceId uniquely identifies a port egress queue group in the managed system.

OBJECT-TYPE

The value of tPortNetEgrQGrpRowStatus allows entries to be created and deleted in the tPortNetEgrQGrpTable. The creation of an entry in this table will succeed only if the queue-group being created exist in TIMETRA-QOS-MIB::tQosEgrQGroupTable.

OBJECT-TYPE

The value of tPortNetEgrQGrpLastChgd indicates the value of sysUpTime when the queue entry was last modified.

OBJECT-TYPE

The value of tPortNetEgrQGrpSchedPol specifies the name of the scheduler policy to be used with this port egress queue-group.

OBJECT-TYPE

The value of tPortNetEgrQGrpAggRateLimit specifies the maximum total rate of all egress queues in this queue-group. The value '-1' means that there is no limit. This object is obsoleted in 13.0 release and replaced by tPortNetEgrQGrpAggRateLmt.

OBJECT-TYPE

The value of tPortNetEgrQGrpAcctgPolId specifies the accounting-policy to be used with this port egress queue-group. A non-zero value indicates the tmnxLogApPolicyId index identifying the policy entry in the tmnxLogApTable from the TIMETRA-LOG-MIB which is associated with this queue-group. The value zero indicates that the agent should use the default accounting policy, if one exists.

OBJECT-TYPE

The value of tPortNetEgrQGrpCollectStats specifies whether statistics should be collected on this port egress queue-group.

OBJECT-TYPE

The value of tPortNetEgrQGrpFrameBaseActg specifies whether to use frame-based accounting for this port egress queue-group. If the value is 'false', the default packet-based accounting method will be used.

OBJECT-TYPE

The value of tPortNetEgrQGrpDescr specifies the description for this port queue-group.

OBJECT-TYPE

The value of tPortNetEgrQGrpPlcrCntrlPolicy specifies the network egress policer control policy applicable to this port egress queue-group.

OBJECT-TYPE

The value of tPortNetEgrQGrpInstanceId defines the unique instance of the port Egress Queue Group. It, along with tPortNetEgrQGrpName, uniquely identifies a port egress queue group in the managed system.

OBJECT-TYPE

The value of tPortNetEgrQGrpAggRateLUB specifies whether to limit the unused bandwidth and allow a tighter control in allocation of bandwidth by HQos. When the value of tPortNetEgrQGrpAggRateLUB is set to 'true', HQos algorithm distributes any unused aggregate bandwidth between queues operating below their fair share rates. This allows a simplified aggregate rate protection while allocating bandwidth by HQos scheduling algorithm.

OBJECT-TYPE

The value of tPortNetEgrQGrpAggRateLmt specifies the maximum total rate of all egress queues in this queue-group. The The value of 4294967295 (0xFFFFFFFF) means that there is no limit.

OBJECT-TYPE

The value of tPortNetEgrQGrpHsTurboQueues specifies whether to enable resource allocation of fast HS Queue-Group queues (set of 8 queues) which are capable of handling higher speed. The value of this object has no effect on non-HS port.

OBJECT-TYPE

The value of tPortNetEgrQOverTableLastChgd indicates the timestamp of last change to the tPortNetEgrQOverTable.

OBJECT-TYPE

The tPortNetEgrQOverTable has an entry for each port queue override configured on this system.

OBJECT-TYPE

Each row represents a particular port queue override. Entries are created and deleted by the user.

OBJECT-TYPE

The value of tPortNetEgrQOverQueue specifies the queue ID which is used as the fourth index to the table entry.

OBJECT-TYPE

The value of tPortNetEgrQOverRowStatus is used for the creation and deletion of port queue overrides. Row creation will fail if there is no entry in the TIMETRA-QOS-MIB::tQosEgrQueueTable with the same index values as the last two indices of this table (tPortNetEgrQGrpName.tPortNetEgrQOverQueue).

OBJECT-TYPE

The value of tPortNetEgrQOverLastChanged indicates the value of sysUpTime at the time of the most recent management change to this row.

OBJECT-TYPE

The value of tPortNetEgrQOverCBS specifies the amount of reserved buffer space for the queue.

OBJECT-TYPE

The value of tPortNetEgrQOverMBS specifies the maximum amount of buffer space allowed for the queue. This object is replaced with tPortNetEgrQOverMBSBytes object.

OBJECT-TYPE

The value of tPortNetEgrQOverHiPrioOnly specifies the percentage of buffer space for the queue, used exclusively by high priority packets. This object is obsoleted in 15.0 release and has been replaced with tPortNetEgrQDrpTailLowReductnMbs object.

OBJECT-TYPE

The value of tPortNetEgrQOverAdminPIR specifies the administrative PIR specified by the user. An 'inconsistentValue' error is returned if tPortNetEgrQOverAdminPIR is set to non-default value when the object tPortNetEgrQOverRateType is set to 'percent'.

OBJECT-TYPE

The value of tPortNetEgrQOverAdminCIR specifies the administrative CIR specified by the user. An 'inconsistentValue' error is returned if tPortNetEgrQOverAdminCIR is set to non-default value when the object tPortNetEgrQOverRateType is set to 'percent'.

OBJECT-TYPE

The value of tPortNetEgrQOverPIRAdaptation specifies the adaptation rule to be used while computing the operational PIR value. The adaptation rule specifies the rules to compute the operational values while maintaining minimum offset.

OBJECT-TYPE

The value of tPortNetEgrQOverCIRAdaptation specifies the adaptation rule to be used while computing the operational CIR value. The adaptation rule specifies the rules to compute the operational values while maintaining minimum offset.

OBJECT-TYPE

The value of tPortNetEgrQOverMBSBytes specifies the maximum amount of buffer space allowed for the queue.

OBJECT-TYPE

The value of tPortNetEgrQOverAdminPIRPercent specifies the administrative PIR percentage, in centipercent. An 'inconsistentValue' error is returned if tPortNetEgrQOverAdminPIRPercent is set to non-default value when the object tPortNetEgrQOverRateType is set to 'kbps'.

OBJECT-TYPE

The value of tPortNetEgrQOverAdminCIRPercent specifies the administrative CIR percentage, in centipercent. An 'inconsistentValue' error is returned if tQosEgrQueueAdminCIRPercent is set to non-default value when the object tPortNetEgrQOverRateType is set to 'kbps'.

OBJECT-TYPE

The value of tPortNetEgrQOverRateType specifies the type of Egress queue rate. When the value of the object is set to 'kbps', the egresss queue rates are specified in kbps. The objects tPortNetEgrQOverAdminPIRPercent and tPortNetEgrQOverAdminCIRPercent will be set to their default values. When the value of the object is set to 'percent', the egress queue rates are specified in percentage. The objects tPortNetEgrQOverAdminPIR and tPortNetEgrQOverAdminCIR will be set to their default values.

OBJECT-TYPE

The value of tPortNetEgrQOverMonitorDepth specifies whether to enable queue depth monitoring for this specified queue.

OBJECT-TYPE

The value of tPortNetEgrQDrpTailLowReductnMbs specifies the percentage at which low drop tail is being reduced from the MBS specified by tPortNetEgrQOverMBSBytes.

OBJECT-TYPE

The tmnxBundleMlfrTable contains MLFR specific data.

OBJECT-TYPE

Each row entry contains data on an MLFR Bundle.

OBJECT-TYPE

The value of tmnxBundleMlfrBundleId is the Bundle Identifier sent with each Link Integrity Protocol message for each member of a tmnxBundleBundleID. The object tmnxPortAdminStatus must be set to 'outOfService' to change this value.

OBJECT-TYPE

The value of tmnxBundleMlfrIngQoSProfId specifies the ingress QoS profile to be used for the incoming traffic over this MLFR bundle. The value of tmnxBundleMlfrIngQoSProfId of 0 indicates a default QoS profile is used as applicable to given hardware.

OBJECT-TYPE

The value of tmnxBundleMlfrEgrQoSProfId specifies the egress QoS profile to be used for the outgoing traffic over this MLFR bundle. The value of tmnxBundleMlfrEgrQoSProfId of 0 indicates a default profile is used as applicable to given hardware.

OBJECT-TYPE

The value of tmnxBundleMlfrHelloTimer specifies the rate at which hello messages are sent across a member link.

OBJECT-TYPE

The value of tmnxBundleMlfrHelloRetryCount specifies the number of times to attempt to resend hello messages when the tmnxBundleMlfrAckTimer has expired before taking action.

OBJECT-TYPE

The value of tmnxBundleMlfrAckTimer specifies the length of time to wait for acknowledgment of a hello message before declaring the hello message has not been received.

OBJECT-TYPE

The value of tmnxBundleMlfrLastChanged indicates the value of sysUpTime at the time of the most recent management change to this row.

OBJECT-TYPE

A table that contains ingress QoS queue-group queue port statistics.

OBJECT-TYPE

Ingress statistics about a specific port's QoS queue-group queue.

OBJECT-TYPE

The value of tmnxPortIngQosQStatQueueId specifies the queue-group queue ID which is used as the fourth index to the table entry.

OBJECT-TYPE

The value of tmnxPortIngQosQStatOffHiPrioPkts indicates the number of high priority packets, as determined by the port ingress QoS policy, offered by the Pchip to the Qchip.

OBJECT-TYPE

The value of tmnxPortIngQosQStatDpdHiPrioPkts indicates the number of high priority packets, as determined by the port ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The value of tmnxPortIngQosQStatOffLoPrioPkts indicates the number of low priority packets, as determined by the port ingress QoS policy, offered by the Pchip to the Qchip.

OBJECT-TYPE

The value of tmnxPortIngQosQStatDpdLoPrioPkts indicates the number of low priority packets, as determined by the port ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The value of tmnxPortIngQosQStatOffHiPrioOcts indicates the number of high priority octets, as determined by the port ingress QoS policy, offered by the Pchip to the Qchip.

OBJECT-TYPE

The value of tmnxPortIngQosQStatDpdHiPrioOcts indicates the number of high priority octets, as determined by the port ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The value of tmnxPortIngQosQStatOffLoPrioOcts indicates the number of low priority octets, as determined by the port ingress QoS policy, offered by the Pchip to the Qchip.

OBJECT-TYPE

The value of tmnxPortIngQosQStatDpdLoPrioOcts indicates the number of low priority octets, as determined by the port ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The value of tmnxPortIngQosQStatFwdInProfPkts indicates the number of in-profile packets (rate below CIR) forwarded by the ingress Qchip.

OBJECT-TYPE

The value of tmnxPortIngQosQStatFwdOutProfPkts indicates the number of out-of-profile packets (rate above CIR) forwarded by the ingress Qchip.

OBJECT-TYPE

The value of tmnxPortIngQosQStatFwdInProfOcts indicates the number of in-profile octets (rate below CIR) forwarded by the ingress Qchip.

OBJECT-TYPE

The value of tmnxPortIngQosQStatFwdOutProfOcts indicates the number of out-of-profile octets (rate above CIR) forwarded by the ingress Qchip.

OBJECT-TYPE

The value of tmnxPortIngQosQStatUncolPktsOff indicates the number of uncolored packets offered to the ingress Qchip.

OBJECT-TYPE

The value of tmnxPortIngQosQStatUncolOctsOff indicates the number of uncolored octets offered to the ingress Qchip.

OBJECT-TYPE

A table that contains egress QoS queue-group queue port statistics.

OBJECT-TYPE

Egress statistics about a specific port's QoS queue-group queue. In release 11.0, tPortAccEgrQGrpInstanceId is added as another index before tmnxPortEgrQosQStatQueueId for this tmnxPortEgrQosQStatTable.

OBJECT-TYPE

The value of tmnxPortEgrQosQStatQueueId specifies the queue-group queue ID which is used as the fourth index to the table entry.

OBJECT-TYPE

The value of tmnxPortEgrQosQStatFwdInProfPkts indicates the number of in-profile packets (rate below CIR) forwarded by the egress Qchip.

OBJECT-TYPE

The value of tmnxPortEgrQosQStatDpdInProfPkts indicates the number of in-profile packets discarded by the egress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The value of tmnxPortEgrQosQStatFwdOutProfPkts indicates the number of out-of-profile packets (rate above CIR) forwarded by the egress Qchip.

OBJECT-TYPE

The value of tmnxPortEgrQosQStatDpdOutProfPkts indicates the number of out-of-profile packets discarded by the egress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The value of tmnxPortEgrQosQStatFwdInProfOcts indicates the number of in-profile octets (rate below CIR) forwarded by the egress Qchip.

OBJECT-TYPE

The value of tmnxPortEgrQosQStatDpdInProfOcts indicates the number of in-profile octets discarded by the egress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The value of tmnxPortEgrQosQStatFwdOutProfOcts indicates the number of out-of-profile octets (rate above CIR) forwarded by the egress Qchip.

OBJECT-TYPE

The value of tmnxPortEgrQosQStatDpdOutProfOcts indicates the number of out-of-profile octets discarded by the egress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The tmnxBundleMemberMlfrTable has an entry for a frame relay link associated with an MLFR Bundle.

OBJECT-TYPE

Each row entry represents an frame relay link associated with a MLFR Bundle.

OBJECT-TYPE

The value of tmnxBundleMemberMlfrDownReason indicates the reason code for marking the MLFR member link of the bundle to down (i.e. tmnxBundleMemberActive will be set to false).

OBJECT-TYPE

The tmnxWaveTrackerTable has an entry for each Wavelength Tracker port on each IOM card in each chassis in the TMNX system.

OBJECT-TYPE

Each row entry represents a Wave Tracker capable port on a IOM card in a chassis in the system. Entries cannot be created and deleted via SNMP SET operations. The tmnxWaveTrackerEntry contains attributes that are unique to the Wave Tracker capable ports.

OBJECT-TYPE

The value of tmnxWaveTrackerPowerCtrlEnable specifies whether or not the Wavelength Tracker Power Control loop that maintains the interface's transmitted optical signal average output power is enabled. tmnxWaveTrackerPowerCtrlEnable is equivalent to 'tnWtEncodePortCapabilityProgrammed' of the 1696-Roadm MIBs.

OBJECT-TYPE

the value of tmnxWaveTrackerEncodeEnable specifies whether or not the Wavelength Tracker Encoding of Wave Keys on the interface's transmitted optical signal is enabled. tmnxWaveTrackerEncodeEnable is equivalent to 'tnWaveKeyEncodeTransmitState' of the 1696-Roadm MIBs.

OBJECT-TYPE

The value of tmnxWaveTrackerInUse indicates whether or not the Wavelength Tracker feature is in use by the system for services. tmnxWaveTrackerInUse is equivalent to 'tnWtEncodePortCapabilityInUse' of the 1696-Roadm MIBs.

OBJECT-TYPE

The value of tmnxWaveTrackerTargetPower specifies the desired average output power of the interface's transmitted optical signal when tmnxWaveTrackerPowerCtrlEnable is set to 'true (1)'. The UNITS millibels (mBm) are units of 0.01 decibel relative to one milliwatt (0 dBm) or dBm multiplied by 100. The mBm is used when integers are required instead of floating point. For example: -5.21 dBm is equivalent to -521 mBm.

OBJECT-TYPE

The value of tmnxWaveTrackerWaveKey1 specifies the first Wavelength Tracker Key (or Identifier) to be transmitted on the interface's optical signal when tmnxWaveTrackerEncodeEnable is set to 'true (1)'. The following table describes the possible tmnxWaveTrackerWaveKey1 and tmnxWaveTrackerWaveKey2 values based on ITU channel. Key1 and Key2 must also match in modulo 2 with each other. Index ITU Key 1 Key 2 channel First Last First Last ------------------------------------------- 0 61 1548 1548 2032 2032 // 1696 Test Channel // Original Tropic Channels (index 1 to 32) 1 59 1 15 545 559 2 58 18 32 562 576 3 57 35 49 579 593 4 56 52 66 596 610 5 54 69 83 613 627 6 53 86 100 630 644 7 52 103 117 647 661 8 51 120 134 664 678 9 49 137 151 681 695 10 48 154 168 698 712 11 47 171 185 715 729 12 46 188 202 732 746 13 44 205 219 749 763 14 43 222 236 766 780 15 42 239 253 783 797 16 41 256 270 800 814 17 39 273 287 817 831 18 38 290 304 834 848 19 37 307 321 851 865 20 36 324 338 868 882 21 34 341 355 885 899 22 33 358 372 902 916 23 32 375 389 919 933 24 31 392 406 936 950 25 29 409 423 953 967 26 28 426 440 970 984 27 27 443 457 987 1001 28 26 460 474 1004 1018 29 24 477 491 1021 1035 30 23 494 508 1038 1052 31 22 511 525 1055 1069 32 21 528 542 1072 1086 // 1696 Extension 42 channels (index 33 to 42) 33 60 1089 1103 1573 1587 34 55 1106 1120 1590 1604 35 50 1123 1137 1607 1621 36 45 1140 1154 1624 1638 37 40 1157 1171 1641 1655 38 35 1174 1188 1658 1672 39 30 1191 1205 1675 1689 40 25 1208 1222 1692 1706 41 20 1225 1239 1709 1723 42 19 1242 1256 1726 1740 // 1830 Extension to 44 channels (index 43 and 44) 43 18 1259 1273 1743 1757 44 17 1276 1290 1760 1774 // 1830 Extension to 88 channels (index 45 to 88) 45 595 1293 1307 1777 1791 46 585 1310 1324 1794 1808 47 575 1327 1341 1811 1825 48 565 1344 1358 1828 1842 49 545 1361 1375 1845 1859 50 535 1378 1392 1862 1876 51 525 1395 1409 1879 1893 52 515 1412 1426 1896 1910 53 495 1429 1443 1913 1927 54 485 1446 1460 1930 1944 55 475 1463 1477 1947 1961 56 465 1480 1494 1964 1978 57 445 1497 1511 1981 1995 58 435 1514 1528 1998 2012 59 425 1531 1545 2015 2029 60 415 1548 1562 2032 2046 61 395 3585 3599 2049 2063 62 385 3602 3616 2066 2080 63 375 3619 3633 2083 2097 64 365 3636 3650 2100 2114 65 345 3653 3667 2117 2131 66 335 3670 3684 2134 2148 67 325 3687 3701 2151 2165 68 315 3704 3718 2168 2182 69 295 3721 3735 2185 2199 70 285 3738 3752 2202 2216 71 275 3755 3769 2219 2233 72 265 3772 3786 2236 2250 73 245 3789 3803 2253 2267 74 235 3806 3820 2270 2284 75 225 3823 3837 2287 2301 76 215 3840 3854 2304 2318 77 605 3857 3871 2321 2335 78 555 3874 3888 2338 2352 79 505 3891 3905 2355 2369 80 455 3908 3922 2372 2386 81 405 3434 3448 3946 3960 82 355 3451 3465 3963 3977 83 305 3468 3482 3980 3994 84 255 3485 3499 3997 4011 85 205 3502 3516 4014 4028 86 195 3519 3533 4031 4045 87 185 3536 3550 4048 4062 88 175 3553 3567 4065 4079 -------------------------------------------

OBJECT-TYPE

the value of tmnxWaveTrackerWaveKey2 specifies the second Wavelength Tracker Key (or Identifier) to be transmitted on the interface's optical signal when tmnxWaveTrackerEncodeEnable is set to 'true (1)'. Refer to the description of tmnxWaveTrackerWaveKey1 for the valid values based on the ITU channel.

OBJECT-TYPE

The value of tmnxWaveTrackerTrailName indicates the trail name of the encode point. This trail is usually transmitted in the OTU pm-tti. tmnxWaveTrackerTrailName is equivalent to 'tnWaveKeyEncodeTrailName' of the 1696-Roadm MIBs.

OBJECT-TYPE

The value of tmnxWaveTrackerCfgAlarms specifies the alarms that are to be monitored by the Wavelength Tracker interface. If an alarm bit is set, then the corresponding alarm will generate a raise or clear notification when its state changes. An unset bit specifies that the alarm corresponding with the bit will not report on its state transitions.

OBJECT-TYPE

The value of tmnxWaveTrackerAlarmState indicates which monitored alarms are raised against the Wavelength Tracker interface.

OBJECT-TYPE

tmnxWaveTrackerMeasuredPower indicates the current average output power of the interface's transmitted optical signal. The UNITS mBm are units of 0.01 dBm or dBm multiplied by 100. The mBm is used when integers are required instead of floating point. For example: -5.21 dBm is equivalent to -521 mBm.

OBJECT-TYPE

tmnxWaveTrackerMaxAttainablePwr indicates the maximum average output power of the interface's transmitted optical signal at end of life. The UNITS mBm are units of 0.01 dBm or dBm multiplied by 100. The mBm is used when integers are required instead of floating point. For example: -5.21 dBm is equivalent to -521 mBm.

OBJECT-TYPE

tmnxWaveTrackerMinAttainablePwr indicates the minimum average output power of the interface's transmitted optical signal at end of life. The UNITS mBm are units of 0.01 dBm or dBm multiplied by 100. The mBm is used when integers are required instead of floating point. For example: -5.21 dBm is equivalent to -521 mBm.

OBJECT-TYPE

tmnxWaveTrackerUpperPowerMargin indicates how much the average output power of the interface's transmitted optical signal can be increased. The UNITS millibels (mB) are units of 0.01 dB or dB multiplied by 100. The mB is used when integers are required instead of floating point. For example: 5.21 dB is equivalent to 521 mB.

OBJECT-TYPE

tmnxWaveTrackerLowerPowerMargin indicates how much the average output power of the interface's transmitted optical signal can be decreased. The UNITS mBm are units of 0.01 dB or dB multiplied by 100. The mB is used when integers are required instead of floating point. For example: 5.21 dB is equivalent to 521 mB.

OBJECT-TYPE

The value of tmnxWaveTrackerPortType indicates if the port is fixed or if it supports pluggable equipment.

OBJECT-TYPE

The value of tmnxWaveTrackerSfpVoaEquipped indicates whether or not an SFP VOA is present.

OBJECT-TYPE

The value of tmnxWaveTrackerSfpVoaType indicates if the SFP VOA is fast or slow.

OBJECT-TYPE

The value of tmnxWaveTrackerSfpVoaSerialNum indicates the serial number information for the SFP VOA. The string is expected to contain printable ASCII characters, but unprintable ASCII characters read from the EEPROM are not filtered out.

OBJECT-TYPE

The value of tmnxWaveTrackerSfpVoaModelNum indicates the model information for the SFP VOA. The string is expected to contain printable ASCII characters, but unprintable ASCII characters read from the EEPROM are not filtered out.

OBJECT-TYPE

The value of tPortAccEgrQGrpHMTableLastChgd indicates the timestamp of last change to the tPortAccEgrQGrpHostMatchTable.

OBJECT-TYPE

The value of tPortAccEgrQGrpHostMatchTable defines a set of string values optionally used by subscriber management to map subscriber's and subscriber host's policed traffic to a specific egress port queue group.

OBJECT-TYPE

The value of tPortAccEgrQGrpHostMatchEntry defines an entry in the tPortAccEgrQGrpHostMatchTable. Entries are created/deleted in this table by SNMP sets to tPortAccEgrQGrpHMRowStatus.

OBJECT-TYPE

The value of tPortAccEgrQGrpHMIntDestId defines the intermediate destination id to match on.

OBJECT-TYPE

The value of tPortAccEgrQGrpHMOrgString defines the organization string to match on. If tPortAccEgrQGrpHMOrgString is the empty string (''), every subscriber with an organization string will not match this entry. If tPortAccEgrQGrpHMOrgString is the wildcard symbol ('*'), every subscriber with an organization string will match this entry, if the tPortAccEgrQGrpHMIntDestId matches. Currently only the empty string ('') is accepted.

OBJECT-TYPE

The value of tPortAccEgrQGrpHMRowStatus allows entries to be created and deleted in the tPortAccEgrQGrpHostMatchTable. The creation of an entry in this table will succeed only if the queue-group being created exist in TIMETRA-QOS-MIB::tQosEgrQGroupTable.

OBJECT-TYPE

The value of tPortAccEgrQGrpHMLastChgd indicates the value of sysUpTime when the host match entry was last modified.

OBJECT-TYPE

The value of tPortAccIngSchedStatTable defines access Ingress Queue Group related statistics per scheduler.

OBJECT-TYPE

The value of tPortAccIngSchedStatEntry defines an entry in the tPortAccIngSchedStatTable. It represents statistics about a specific QoS ingress queue group scheduler on the port specified by tPortAccIngSchedStatName on the access side.

OBJECT-TYPE

The value of tPortAccIngSchedStatName indicates the scheduler associated with this queue group on this port.

OBJECT-TYPE

The value of tPortAccIngSchedStatFwdPkts indicates the number of forwarded packets by this port on this queue-group using this scheduler.

OBJECT-TYPE

The value of tPortAccIngSchedStatFwdPktsHi indicates upper 32 bits of tPortAccIngSchedStatFwdPkts object.

OBJECT-TYPE

The value of tPortAccIngSchedStatFwdPktsLo indicates lower 32 bits of tPortAccIngSchedStatFwdPkts object.

OBJECT-TYPE

The value of tPortAccIngSchedStatFwdOcts indicates the number of forwarded octets by this port on this queue-group using this scheduler.

OBJECT-TYPE

The value of tPortAccIngSchedStatFwdOctsHi indicates upper 32 bits of tPortAccIngSchedStatFwdOcts object.

OBJECT-TYPE

The value of tPortAccIngSchedStatFwdOctsLo indicates lower 32 bits of tPortAccIngSchedStatFwdOcts object.

OBJECT-TYPE

The value of tPortAccEgrSchedStatTable defines access Egress Queue Group related statistics per scheduler.

OBJECT-TYPE

The value of tPortAccEgrSchedStatEntry defines an entry in the tPortAccEgrSchedStatTable. It represents statistics about a specific QoS egress queue group scheduler on the port specified by tPortAccEgrSchedStatName on the access side. In release 11.0, tPortAccEgrQGrpInstanceId is added as another index before tPortAccEgrSchedStatName for this tPortAccEgrSchedStatTable.

OBJECT-TYPE

The value of tPortAccEgrSchedStatName indicates the scheduler associated with this queue group on this port.

OBJECT-TYPE

The value of tPortAccEgrSchedStatFwdPkts indicates the number of forwarded packets by this port on this queue-group using this scheduler.

OBJECT-TYPE

The value of tPortAccEgrSchedStatFwdPktsHi indicates upper 32 bits of tPortAccEgrSchedStatFwdPkts object.

OBJECT-TYPE

The value of tPortAccEgrSchedStatFwdPktsLo indicates lower 32 bits of tPortAccEgrSchedStatFwdPkts object.

OBJECT-TYPE

tPortAccEgrSchedStatFwdOcts indicates the number of forwarded octets by this port on this queue-group using this scheduler.

OBJECT-TYPE

The value of tPortAccEgrSchedStatFwdOctsHi indicates upper 32 bits of tPortAccEgrSchedStatFwdOcts object.

OBJECT-TYPE

The value of tPortAccEgrSchedStatFwdOctsLo indicates lower 32 bits of tPortAccEgrSchedStatFwdOcts object.

OBJECT-TYPE

The value of tPortNetEgrSchedStatTable defines network Egress Queue Group related statistics per scheduler.

OBJECT-TYPE

The value of tPortNetEgrSchedStatEntry defines an entry in the tPortNetEgrSchedStatTable. It represents statistics about a specific QoS egress queue group scheduler on the port specified by tPortNetEgrSchedStatName on the network side.

OBJECT-TYPE

The value of tPortNetEgrSchedStatName indicates the scheduler associated with this queue group on this port.

OBJECT-TYPE

The value of tPortNetEgrSchedStatFwdPkts indicates the number of forwarded packets by this port on this queue-group using this scheduler.

OBJECT-TYPE

The value of tPortNetEgrSchedStatFwdPktsHi indicates upper 32 bits of tPortNetEgrSchedStatFwdPkts object.

OBJECT-TYPE

tPortNetEgrSchedStatFwdPktsLo indicates lower 32 bits of tPortNetEgrSchedStatFwdPkts object.

OBJECT-TYPE

The value of tPortNetEgrSchedStatFwdOcts indicates the number of forwarded octets by this port on this queue-group using this scheduler.

OBJECT-TYPE

tPortNetEgrSchedStatFwdOctsHi indicates upper 32 bits of tPortNetEgrSchedStatFwdOcts object.

OBJECT-TYPE

The value of tPortNetEgrSchedStatFwdOctsLo indicates lower 32 bits of tPortNetEgrSchedStatFwdOcts object.

OBJECT-TYPE

The value of tPortEgrVPortTableLastChgd indicates the timestamp of last change to the tPortEgrVPortTable.

OBJECT-TYPE

The tPortEgrVPortTable has an entry for each virtual port defined on this port.

OBJECT-TYPE

Each row entry represents a virtual port defined on the port for the chassis in the system.

OBJECT-TYPE

The value of tPortEgrVPortName is the name of the virtual port on this port.

OBJECT-TYPE

The value of tPortEgrVPortRowStatus specifies the row status of this entry in this table.

OBJECT-TYPE

The value of tPortEgrVPortLastChanged indicates the time stamp of the last change in this entry.

OBJECT-TYPE

The value of tPortEgrVPortDescr specifies the description of the virtual port.

OBJECT-TYPE

The value of tPortEgrVPortSchedPol specifies the name of the port scheduler policy assigned to this virtual port.

OBJECT-TYPE

The value of tPortEgrVPortAggRateLimit specifies the maximum total rate of all subscribers for this virtual port. The value -1 means that there is no limit. This object is obsoleted in 13.0 release and replaced by tPortEgrVPortAggRateLmt.

OBJECT-TYPE

The value of tPortEgrVPortEgrRateModify specifies if egress-rate modification is enabled. Egress-rate-modification takes the egress bandwidth already in use for multicast traffic into account while performing rate limiting according to the values of tPortEgrVPortAggRateLimit or tPortEgrVPortSchedPol, in order to avoid that the sum of unicast and multicast bandwidths would exceed the egress aggregate rate limit.

OBJECT-TYPE

The value of tPortEgrVPortEgrRateModifyDelta indicates the actual bandwidth correction applied while the value of the object tPortEgrVPortEgrRateModify is 'enabled'.

OBJECT-TYPE

The value of tPortEgrVPortQosSchedPolicy specifies the QoS egress scheduler policy (from TIMETRA-QOS-MIB::tSchedulerPolicyTable) applicable to this virtual port.

OBJECT-TYPE

The value of tPortEgrVPortAggRateLUB specifies whether to limit the unused bandwidth and allow a tighter control in allocation of bandwidth by HQos. When the value of tPortEgrVPortAggRateLUB is set to 'true', HQos algorithm distributes any unused aggregate bandwidth between queues operating below their fair share rates. This allows a simplified aggregate rate protection while allocating bandwidth by HQos scheduling algorithm.

OBJECT-TYPE

The value of tPortEgrVPortAggRateLmtHi specifies the upper 32 bits of the maximum total rate of all subscribers for this virtual port. When the value of tPortEgrVPortAggRateLmtHi along with the value of tPortEgrVPortAggRateLmt is set to 4294967295 (0xFFFFFFFF), rate for this virtual port indicates maximum total rate.

OBJECT-TYPE

The value of tPortEgrVPortAggRateLmt specifies the maximum total rate of all subscribers for this virtual port. The value of 4294967295 (0xFFFFFFFF) means that there is no limit. When the value of tPortEgrVPortAggRateLmtHi along with the value of tPortEgrVPortAggRateLmt is set to 4294967295 (0xFFFFFFFF), rate for this virtual port indicates maximum total rate.

OBJECT-TYPE

The value of tPortEgrVPortMonitorPortSched specifies whether to enable monitoring of port scheduler specified by tPortEgrVPortSchedPol.

OBJECT-TYPE

The value of tPortEgrVPortHMTableLastChgd indicates the timestamp of last change to the tPortEgrVPortHostMatchTable.

OBJECT-TYPE

The value of tPortEgrVPortHostMatchTable defines a set of string values optionally used by subscriber management to map subscriber's and subscriber host's queued traffic to a specific egress port virtual port.

OBJECT-TYPE

The value of tPortEgrVPortHostMatchEntry defines an entry in the tPortEgrVPortHostMatchTable. Entries are created/deleted in this table by SNMP sets to tPortEgrVPortHMRowStatus.

OBJECT-TYPE

The value of tPortEgrVPortHMIntDestId defines the intermediate destination id to match on.

OBJECT-TYPE

The value of tPortEgrVPortHMOrgString defines the organization string to match on. If tPortEgrVPortHMOrgString is the empty string (''), every subscriber with an organization string will not match this entry. If tPortEgrVPortHMOrgString is the wildcard symbol ('*'), every subscriber with an organization string will match this entry, if the tPortEgrVPortHMIntDestId matches. Currently only the empty string ('') is accepted.

OBJECT-TYPE

The value of tPortEgrVPortHMRowStatus allows entries to be created and deleted in the tPortEgrVPortHostMatchTable.

OBJECT-TYPE

The value of tPortEgrVPortHMLastChgd indicates the value of sysUpTime when the host match entry was last modified.

OBJECT-TYPE

The tmnxOpticalPortCfgTable has an entry for each DWDM Optical port on each IOM card in each chassis in the Nokia SROS system. This table was marked obsolete in 15.1. There is no replacement table.

OBJECT-TYPE

Each row entry represents an Optical port on a IOM card in a chassis in the system. Entries cannot be created and deleted via SNMP SET operations. The tmnxOpticalPortCfgEntry contains attributes that are unique to the Optical ports.

OBJECT-TYPE

The value of tmnxOpticalPortAmpCfgAlarms specifies the alarms that are monitored by the optical amplifier interface. If an alarm bit is set, then the corresponding alarm will generate a raise or clear notification when its state changes. An unset bit specifies that the alarm corresponding with the bit will not report on its state transitions. This object was marked obsolete in 15.1. There is no replacement object.

OBJECT-TYPE

The value of tmnxOpticalPortTdcmCtrlMode specifies the current operational mode of the tunable dispersion compensation module. When tmnxOpticalPortTdcmCtrlMode is set to automatic, the dispersion setpoint can be retrieved from tmnxOpticalPortTdcmAutoDisp. When tmnxOpticalPortTdcmCtrlMode is set to manual, the dispersion setpoint can be configured with tmnxOpticalPortTdcmManCfgDisp. This object was marked obsolete in 15.1. There is no replacement object.

OBJECT-TYPE

The value of tmnxOpticalPortTdcmManCfgDisp specifies the manually configured dispersion of the tunable dispersion compensation module. This parameter is valid when the tmnxOpticalPortTdcmCtrlMode is manual. Dispersion is expressed in picoseconds per nanometer (ps/nm). This object was marked obsolete in 15.1. There is no replacement object.

OBJECT-TYPE

tmnxOpticalPortTdcmCfgRxChan specifies the DWDM ITU channel at which the tunable dispersion compensation module should operate. If a value of zero(0) has been specified, tmnxOpticalPortTdcmPresRxChan will be changed by the system to be equivalent to tmnxPortDwdmLaserChannel. tmnxOpticalPortTdcmCfgRxChan should be set to the same value as tmnxPortDwdmLaserChannel in most cases, but may be set to a different value when the received wavelength is different from the transmitted wavelength. This object was marked obsolete in 15.1. There is no replacement object.

OBJECT-TYPE

The value of tmnxOpticalPortTdcmCfgAlarms specifies the alarms that are monitored by the tunable dispersion compensation module's interface. If an alarm bit is set, then the corresponding alarm will generate a raise or clear notification when its state changes. An unset bit specifies that the alarm corresponding with the bit will not report on its state transitions. This object was marked obsolete in 15.1. There is no replacement object.

OBJECT-TYPE

The value of tmnxOpticalPortTdcmDispSwpStart specifies the the start value for dispersion sweeping on a tunable dispersion compensation module. Dispersion is expressed in picoseconds per nanometer (ps/nm). This object was marked obsolete in 15.1. There is no replacement object.

OBJECT-TYPE

The value of tmnxOpticalPortTdcmDispSwpEnd specifies the the end value for dispersion sweeping on a tunable dispersion compensation module. Dispersion is expressed in picoseconds per nanometer (ps/nm). This object was marked obsolete in 15.1. There is no replacement object.

OBJECT-TYPE

The tmnxOpticalPortOperTable has an entry for each DWDM Optical port on each IOM card in each chassis in the Nokia SROS system.

OBJECT-TYPE

Each row entry represents an Optical port on a IOM card in a chassis in the system. The tmnxOpticalPortOperEntry contains attributes that are unique to the Optical ports.

OBJECT-TYPE

The value of tmnxOpticalPortHasRxAmplifier indicates whether or not the port has an optical amplifier on the receive path. This object was marked obsolete in 15.1.0R1. There is no replacement object.

OBJECT-TYPE

The value of tmnxOpticalPortHasRxTdcm indicates whether or not the port has an optical tunable dispersion compensation module on the receive path. This object was marked obsolete in 15.1. There is no replacement object.

OBJECT-TYPE

The value of tmnxOpticalPortAmpPowerIn indicates the received average optical power at the input of the optical amplifier. The UNITS millibels (mBm) are units of 0.01 decibel relative to one milliwatt (0 dBm) or dBm multiplied by 100. The mBm is used when integers are required instead of floating point. For example: -5.21 dBm is equivalent to -521 mBm. This object was marked obsolete in 15.1. There is no replacement object.

OBJECT-TYPE

The value of tmnxOpticalPortAmpGain indicates the gain of the optical amplifier. The gain indicates how much the input signal is amplified. The UNITS millibels (mB) are units of 0.01 dB or dB multiplied by 100. The mB is used when integers are required instead of floating point. For example: 5.21 dB is equivalent to 521 mB. This object was marked obsolete in 15.1. There is no replacement object.

OBJECT-TYPE

The value of tmnxOpticalPortAmpPowerOut indicates the optical power at the output of the optical amplifier. The UNITS millibels (mBm) are units of 0.01 decibel relative to one milliwatt (0 dBm) or dBm multiplied by 100. The mBm is used when integers are required instead of floating point. For example: -5.21 dBm is equivalent to -521 mBm. This object was marked obsolete in 15.1. There is no replacement object.