MAU-MIB
- Registered at
- 1.3.6.1.2.1.26
- Last updated
- 2007-04-21 00:00
- Organization
- IETF Ethernet Interfaces and Hub MIB Working Group
- Revisions
- 2007-04-21 00:00, 2003-09-19 00:00, 1999-08-24 04:00, 1997-10-31 00:00, 1993-09-30 00:00
- Namespace
- standard
- Source file
MAU-MIB- Digest
sha256:ab043b1bd7caff2f295f001be20a620d8bdd6ab5827253442284594855fbe696
Description
Management information for 802.3 MAUs. The following reference is used throughout this MIB module: [IEEE802.3] refers to: IEEE Std 802.3, 2005 Edition: 'IEEE Standard for Information technology - Telecommunications and information exchange between systems - Local and metropolitan area networks - Specific requirements - Part 3: Carrier sense multiple access with collision detection (CSMA/CD) access method and physical layer specifications'. Of particular interest is Clause 30, 'Management'. Copyright (C) The IETF Trust (2007). This version of this MIB module is part of RFC 4836; see the RFC itself for full legal notices.
Contact
WG charter: http://www.ietf.org/html.charters/hubmib-charter.html Mailing Lists: General Discussion: hubmib@ietf.org To Subscribe: hubmib-request@ietf.org In Body: subscribe your_email_address Chair: Bert Wijnen Postal: Alcatel-Lucent Schagen 33 3461 GL Linschoten Netherlands Phone: +31-348-407-775 EMail: bwijnen@alcatel-lucent.com Editor: Edward Beili Postal: Actelis Networks Inc. 25 Bazel St., P.O.B. 10173 Petach-Tikva 10173 Israel Tel: +972-3-924-3491 EMail: edward.beili@actelis.com
Imports
| From | Symbols |
|---|---|
| IANA-MAU-MIB | IANAifJackType, IANAifMauAutoNegCapBits, IANAifMauMediaAvailable, IANAifMauTypeListBits |
| IF-MIB | InterfaceIndex |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP |
| SNMPv2-SMI | Counter32, Counter64, Integer32, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, iso, mib-2 |
| SNMPv2-TC | AutonomousType, DisplayString, TEXTUAL-CONVENTION, TruthValue |
Imported by
6 module(s) in this corpus import this one.
Load order
Every file a consumer needs in order to load this module, dependencies first.
IANA-MAU-MIB IANAifType-MIB IF-MIB MAU-MIB SNMPv2-CONF SNMPv2-MIB SNMPv2-SMI SNMPv2-TC
Under this module's arcs
Where the registration tree carries on below this module.
| Arc | Name | Module |
|---|---|---|
| 1.3.6.1.2.1.26.4 | dot3MauType | IANA-MAU-MIB |
Textual conventions
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| JackType TEXTUAL-CONVENTION ********* THIS TC IS DEPRECATED ********** This TC has been deprecated in favour of IANAifJackType. Common enumeration values for repeater and interface MAU jack types. | deprecated |
Objects
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| snmpDot3MauMgt OBJECT-IDENTITY | 1.3.6.1.2.1.26 | |||
| snmpDot3MauTraps OBJECT-IDENTITY | 1.3.6.1.2.1.26.0 | |||
| dot3RpMauBasicGroup OBJECT-IDENTITY | 1.3.6.1.2.1.26.1 | |||
| rpMauTable OBJECT-TYPE Table of descriptive and status information about the MAU(s) attached to the ports of a repeater. | 1.3.6.1.2.1.26.1.1 | not-accessible | current | |
| rpMauEntry OBJECT-TYPE An entry in the table, containing information about a single MAU. | 1.3.6.1.2.1.26.1.1.1 | not-accessible | current | |
| rpMauGroupIndex OBJECT-TYPE This variable uniquely identifies the group containing the port to which the MAU described by this entry is connected. Note: In practice, a group will generally be a field-replaceable unit (i.e., module, card, or board) that can fit in the physical system enclosure, and the group number will correspond to a number marked on the physical enclosure. The group denoted by a particular value of this object is the same as the group denoted by the same value of rptrGroupIndex. | 1.3.6.1.2.1.26.1.1.1.1 | Integer32 (1..2147483647) | read-only | current |
| rpMauPortIndex OBJECT-TYPE This variable uniquely identifies the repeater port within group rpMauGroupIndex to which the MAU described by this entry is connected. | 1.3.6.1.2.1.26.1.1.1.2 | Integer32 (1..2147483647) | read-only | current |
| rpMauIndex OBJECT-TYPE This variable uniquely identifies the MAU described by this entry from among other MAUs connected to the same port (rpMauPortIndex). | 1.3.6.1.2.1.26.1.1.1.3 | Integer32 (1..2147483647) | read-only | current |
| rpMauType OBJECT-TYPE This object identifies the MAU type. Values for standard IEEE 802.3 MAU types are defined in the IANA maintained IANA-MAU-MIB module, as OBJECT-IDENTITIES of dot3MauType. If the MAU type is unknown, the object identifier zeroDotZero is returned. | 1.3.6.1.2.1.26.1.1.1.4 | AutonomousType | read-only | current |
| rpMauStatus OBJECT-TYPE The current state of the MAU. This object MAY be implemented as a read-only object by those agents and MAUs that do not implement software control of the MAU state. Some agents may not support setting the value of this object to some of the enumerated values. The value other(1) is returned if the MAU is in a state other than one of the states 2 through 6. The value unknown(2) is returned when the MAU's true state is unknown; for example, when it is being initialized. A MAU in the operational(3) state is fully functional; it operates, and passes signals to its attached DTE or repeater port in accordance to its specification. A MAU in standby(4) state forces DI and CI to idle, and the media transmitter to idle or fault, if supported. Standby(4) mode only applies to link type MAUs. The state of rpMauMediaAvailable is unaffected. A MAU in shutdown(5) state assumes the same condition on DI, CI, and the media transmitter, as though it were powered down or not connected. The MAU MAY return other(1) value for the rpMauJabberState and rpMauMediaAvailable objects when it is in this state. For an AUI, this state will remove power from the AUI. Setting this variable to the value reset(6) resets the MAU in the same manner as a power-off, power-on cycle of at least one-half second would. The agent is not required to return the value reset(6). Setting this variable to the value operational(3), standby(4), or shutdown(5) causes the MAU to assume the respective state, except that setting a mixing-type MAU or an AUI to standby(4) will cause the MAU to enter the shutdown state. | 1.3.6.1.2.1.26.1.1.1.5 | INTEGER {other(1), unknown(2), operational(3), standby(4), shutdown(5), reset(6)} | read-write | current |
| rpMauMediaAvailable OBJECT-TYPE This object identifies Media Available state of the MAU, complementary to the rpMauStatus. Values for the standard IEEE 802.3 Media Available states are defined in the IANA maintained IANA-MAU-MIB module, as IANAifMauMediaAvailable TC. | 1.3.6.1.2.1.26.1.1.1.6 | IANAifMauMediaAvailable | read-only | current |
| rpMauMediaAvailableStateExits OBJECT-TYPE A count of the number of times that rpMauMediaAvailable for this MAU instance leaves the state available(3). Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times, as indicated by the value of rptrMonitorPortLastChange. | 1.3.6.1.2.1.26.1.1.1.7 | Counter32 | read-only | current |
| rpMauJabberState OBJECT-TYPE The value other(1) is returned if the jabber state is not 2, 3, or 4. The agent MUST always return other(1) for MAU type dot3MauTypeAUI. The value unknown(2) is returned when the MAU's true state is unknown; for example, when it is being initialized. If the MAU is not jabbering the agent returns noJabber(3). This is the 'normal' state. If the MAU is in jabber state the agent returns the jabbering(4) value. | 1.3.6.1.2.1.26.1.1.1.8 | INTEGER {other(1), unknown(2), noJabber(3), jabbering(4)} | read-only | current |
| rpMauJabberingStateEnters OBJECT-TYPE A count of the number of times that mauJabberState for this MAU instance enters the state jabbering(4). For MAUs of type dot3MauTypeAUI, dot3MauType100BaseT4, dot3MauType100BaseTX, dot3MauType100BaseFX, and all 1000Mbps types, this counter will always indicate zero. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times, as indicated by the value of rptrMonitorPortLastChange. | 1.3.6.1.2.1.26.1.1.1.9 | Counter32 | read-only | current |
| rpMauFalseCarriers OBJECT-TYPE A count of the number of false carrier events during IDLE in 100BASE-X links. This counter does not increment at the symbol rate. It can increment after a valid carrier completion at a maximum rate of once per 100 ms until the next carrier event. This counter increments only for MAUs of type dot3MauType100BaseT4, dot3MauType100BaseTX, dot3MauType100BaseFX, and all 1000Mbps types. For all other MAU types, this counter will always indicate zero. The approximate minimum time for rollover of this counter is 7.4 hours. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times, as indicated by the value of rptrMonitorPortLastChange. | 1.3.6.1.2.1.26.1.1.1.10 | Counter32 | read-only | current |
| rpJackTable OBJECT-TYPE Information about the external jacks attached to MAUs attached to the ports of a repeater. | 1.3.6.1.2.1.26.1.2 | not-accessible | current | |
| rpJackEntry OBJECT-TYPE An entry in the table, containing information about a particular jack. | 1.3.6.1.2.1.26.1.2.1 | not-accessible | current | |
| rpJackIndex OBJECT-TYPE This variable uniquely identifies the jack described by this entry from among other jacks attached to the same MAU (rpMauIndex). | 1.3.6.1.2.1.26.1.2.1.1 | Integer32 (1..2147483647) | not-accessible | current |
| rpJackType OBJECT-TYPE The jack connector type, as it appears on the outside of the system. | 1.3.6.1.2.1.26.1.2.1.2 | IANAifJackType | read-only | current |
| dot3IfMauBasicGroup OBJECT-IDENTITY | 1.3.6.1.2.1.26.2 | |||
| ifMauTable OBJECT-TYPE Table of descriptive and status information about MAU(s) attached to an interface. | 1.3.6.1.2.1.26.2.1 | not-accessible | current | |
| ifMauEntry OBJECT-TYPE An entry in the table, containing information about a single MAU. | 1.3.6.1.2.1.26.2.1.1 | not-accessible | current | |
| ifMauIfIndex OBJECT-TYPE This variable uniquely identifies the interface to which the MAU described by this entry is connected. | 1.3.6.1.2.1.26.2.1.1.1 | InterfaceIndex | read-only | current |
| ifMauIndex OBJECT-TYPE This variable uniquely identifies the MAU described by this entry from among other MAUs connected to the same interface (ifMauIfIndex). | 1.3.6.1.2.1.26.2.1.1.2 | Integer32 (1..2147483647) | read-only | current |
| ifMauType OBJECT-TYPE This object identifies the MAU type. Values for standard IEEE 802.3 MAU types are defined in the IANA maintained IANA-MAU-MIB module, as OBJECT-IDENTITIES of dot3MauType. If the MAU type is unknown, the object identifier zeroDotZero is returned. This object represents the operational type of the MAU, as determined by either 1) the result of the auto-negotiation function or 2) if auto-negotiation is not enabled or is not implemented for this MAU, by the value of the object ifMauDefaultType. In case 2), a set to the object ifMauDefaultType will force the MAU into the new operating mode. | 1.3.6.1.2.1.26.2.1.1.3 | AutonomousType | read-only | current |
| ifMauStatus OBJECT-TYPE The current state of the MAU. This object MAY be implemented as a read-only object by those agents and MAUs that do not implement software control of the MAU state. Some agents may not support setting the value of this object to some of the enumerated values. The value other(1) is returned if the MAU is in a state other than one of the states 2 through 6. The value unknown(2) is returned when the MAU's true state is unknown; for example, when it is being initialized. A MAU in the operational(3) state is fully functional; it operates, and passes signals to its attached DTE or repeater port in accordance to its specification. A MAU in standby(4) state forces DI and CI to idle and the media transmitter to idle or fault, if supported. Standby(4) mode only applies to link type MAUs. The state of ifMauMediaAvailable is unaffected. A MAU in shutdown(5) state assumes the same condition on DI, CI, and the media transmitter, as though it were powered down or not connected. The MAU MAY return other(1) value for the ifMauJabberState and ifMauMediaAvailable objects when it is in this state. For an AUI, this state will remove power from the AUI. Setting this variable to the value reset(6) resets the MAU in the same manner as a power-off, power-on cycle of at least one-half second would. The agent is not required to return the value reset(6). Setting this variable to the value operational(3), standby(4), or shutdown(5) causes the MAU to assume the respective state, except that setting a mixing-type MAU or an AUI to standby(4) will cause the MAU to enter the shutdown state. | 1.3.6.1.2.1.26.2.1.1.4 | INTEGER {other(1), unknown(2), operational(3), standby(4), shutdown(5), reset(6)} | read-write | current |
| ifMauMediaAvailable OBJECT-TYPE This object identifies Media Available state of the MAU, complementary to the ifMauStatus. Values for the standard IEEE 802.3 Media Available states are defined in the IANA maintained IANA-MAU-MIB module, as IANAifMauMediaAvailable TC. | 1.3.6.1.2.1.26.2.1.1.5 | IANAifMauMediaAvailable | read-only | current |
| ifMauMediaAvailableStateExits OBJECT-TYPE A count of the number of times that ifMauMediaAvailable for this MAU instance leaves the state available(3). Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times, as indicated by the value of ifCounterDiscontinuityTime. | 1.3.6.1.2.1.26.2.1.1.6 | Counter32 | read-only | current |
| ifMauJabberState OBJECT-TYPE The value other(1) is returned if the jabber state is not 2, 3, or 4. The agent MUST always return other(1) for MAU type dot3MauTypeAUI. The value unknown(2) is returned when the MAU's true state is unknown; for example, when it is being initialized. If the MAU is not jabbering the agent returns noJabber(3). This is the 'normal' state. If the MAU is in jabber state the agent returns the jabbering(4) value. | 1.3.6.1.2.1.26.2.1.1.7 | INTEGER {other(1), unknown(2), noJabber(3), jabbering(4)} | read-only | current |
| ifMauJabberingStateEnters OBJECT-TYPE A count of the number of times that mauJabberState for this MAU instance enters the state jabbering(4). This counter will always indicate zero for MAUs of type dot3MauTypeAUI and those of speeds above 10Mbps. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times, as indicated by the value of ifCounterDiscontinuityTime. | 1.3.6.1.2.1.26.2.1.1.8 | Counter32 | read-only | current |
| ifMauFalseCarriers OBJECT-TYPE A count of the number of false carrier events during IDLE in 100BASE-X and 1000BASE-X links. For all other MAU types, this counter will always indicate zero. This counter does not increment at the symbol rate. It can increment after a valid carrier completion at a maximum rate of once per 100 ms for 100BASE-X and once per 10us for 1000BASE-X until the next CarrierEvent. This counter can roll over very quickly. A management station is advised to poll the ifMauHCFalseCarriers instead of this counter in order to avoid loss of information. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times, as indicated by the value of ifCounterDiscontinuityTime. | 1.3.6.1.2.1.26.2.1.1.9 | Counter32 | read-only | current |
| ifMauTypeList OBJECT-TYPE ********* THIS OBJECT IS DEPRECATED ********** This object has been deprecated in favour of ifMauTypeListBits. A value that uniquely identifies the set of possible IEEE 802.3 types that the MAU could be. The value is a sum that initially takes the value zero. Then, for each type capability of this MAU, 2 raised to the power noted below is added to the sum. For example, a MAU that has the capability to be only 10BASE-T would have a value of 512 (2**9). In contrast, a MAU that supports both 10Base-T (full duplex) and 100BASE-TX (full duplex) would have a value of ((2**11) + (2**16)), or 67584. The powers of 2 assigned to the capabilities are these: Power Capability 0 other or unknown 1 AUI 2 10BASE-5 3 FOIRL 4 10BASE-2 5 10BASE-T duplex mode unknown 6 10BASE-FP 7 10BASE-FB 8 10BASE-FL duplex mode unknown 9 10BROAD36 10 10BASE-T half duplex mode 11 10BASE-T full duplex mode 12 10BASE-FL half duplex mode 13 10BASE-FL full duplex mode 14 100BASE-T4 15 100BASE-TX half duplex mode 16 100BASE-TX full duplex mode 17 100BASE-FX half duplex mode 18 100BASE-FX full duplex mode 19 100BASE-T2 half duplex mode 20 100BASE-T2 full duplex mode If auto-negotiation is present on this MAU, this object will map to ifMauAutoNegCapability. | 1.3.6.1.2.1.26.2.1.1.10 | Integer32 | read-only | deprecated |
| ifMauDefaultType OBJECT-TYPE This object identifies the default administrative baseband MAU type to be used in conjunction with the operational MAU type denoted by ifMauType. The set of possible values for this object is the same as the set defined for the ifMauType object. This object represents the administratively-configured type of the MAU. If auto-negotiation is not enabled or is not implemented for this MAU, the value of this object determines the operational type of the MAU. In this case, a set to this object will force the MAU into the specified operating mode. If auto-negotiation is implemented and enabled for this MAU, the operational type of the MAU is determined by auto-negotiation, and the value of this object denotes the type to which the MAU will automatically revert if/when auto-negotiation is later disabled. NOTE TO IMPLEMENTORS: It may be necessary to provide for underlying hardware implementations which do not follow the exact behavior specified above. In particular, when ifMauAutoNegAdminStatus transitions from enabled to disabled, the agent implementation MUST ensure that the operational type of the MAU (as reported by ifMauType) correctly transitions to the value specified by this object, rather than continuing to operate at the value earlier determined by the auto-negotiation function. | 1.3.6.1.2.1.26.2.1.1.11 | AutonomousType | read-write | current |
| ifMauAutoNegSupported OBJECT-TYPE This object indicates whether or not auto-negotiation is supported on this MAU. | 1.3.6.1.2.1.26.2.1.1.12 | TruthValue | read-only | current |
| ifMauTypeListBits OBJECT-TYPE A value that uniquely identifies the set of possible IEEE 802.3 types that the MAU could be. If auto-negotiation is present on this MAU, this object will map to ifMauAutoNegCapabilityBits. Note that this MAU may be capable of operating as a MAU type that is beyond the scope of this MIB. This is indicated by returning the bit value bOther in addition to any bit values for standard capabilities that are listed in the IANAifMauTypeListBits TC. | 1.3.6.1.2.1.26.2.1.1.13 | IANAifMauTypeListBits | read-only | current |
| ifMauHCFalseCarriers OBJECT-TYPE A count of the number of false carrier events during IDLE in 100BASE-X and 1000BASE-X links. For all other MAU types, this counter will always indicate zero. This counter does not increment at the symbol rate. This counter is a 64-bit version of ifMauFalseCarriers. Since the 32-bit version of this counter can roll over very quickly, management stations are advised to poll the 64-bit version instead, in order to avoid loss of information. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times, as indicated by the value of ifCounterDiscontinuityTime. | 1.3.6.1.2.1.26.2.1.1.14 | Counter64 | read-only | current |
| ifJackTable OBJECT-TYPE Information about the external jacks attached to MAUs attached to an interface. | 1.3.6.1.2.1.26.2.2 | not-accessible | current | |
| ifJackEntry OBJECT-TYPE An entry in the table, containing information about a particular jack. | 1.3.6.1.2.1.26.2.2.1 | not-accessible | current | |
| ifJackIndex OBJECT-TYPE This variable uniquely identifies the jack described by this entry from among other jacks attached to the same MAU. | 1.3.6.1.2.1.26.2.2.1.1 | Integer32 (1..2147483647) | not-accessible | current |
| ifJackType OBJECT-TYPE The jack connector type, as it appears on the outside of the system. | 1.3.6.1.2.1.26.2.2.1.2 | IANAifJackType | read-only | current |
| dot3BroadMauBasicGroup OBJECT-IDENTITY | 1.3.6.1.2.1.26.3 | |||
| broadMauBasicTable OBJECT-TYPE ********* THIS OBJECT IS DEPRECATED ********** This entire table has been deprecated. There have been no reported implementations of this table, and it is unlikely that there ever will be. IEEE recommends that broadband MAU types should not be used for new installations. Table of descriptive and status information about the broadband MAUs connected to interfaces. | 1.3.6.1.2.1.26.3.1 | not-accessible | deprecated | |
| broadMauBasicEntry OBJECT-TYPE ********* THIS OBJECT IS DEPRECATED ********** An entry in the table, containing information about a single broadband MAU. | 1.3.6.1.2.1.26.3.1.1 | not-accessible | deprecated | |
| broadMauIfIndex OBJECT-TYPE ********* THIS OBJECT IS DEPRECATED ********** This variable uniquely identifies the interface to which the MAU described by this entry is connected. | 1.3.6.1.2.1.26.3.1.1.1 | InterfaceIndex | read-only | deprecated |
| broadMauIndex OBJECT-TYPE ********* THIS OBJECT IS DEPRECATED ********** This variable uniquely identifies the MAU connected to interface broadMauIfIndex that is described by this entry. | 1.3.6.1.2.1.26.3.1.1.2 | Integer32 (1..2147483647) | read-only | deprecated |
| broadMauXmtRcvSplitType OBJECT-TYPE ********* THIS OBJECT IS DEPRECATED ********** This object indicates the type of frequency multiplexing/cabling system used to separate the transmit and receive paths for the 10BROAD36 MAU. The value other(1) is returned if the split type is not either single or dual. The value single(2) indicates a single cable system. The value dual(3) indicates a dual cable system, offset normally zero. | 1.3.6.1.2.1.26.3.1.1.3 | INTEGER {other(1), single(2), dual(3)} | read-only | deprecated |
| broadMauXmtCarrierFreq OBJECT-TYPE ********* THIS OBJECT IS DEPRECATED ********** This variable indicates the transmit carrier frequency of the 10BROAD36 MAU in MHz/4; that is, in units of 250 kHz. | 1.3.6.1.2.1.26.3.1.1.4 | Integer32 | read-only | deprecated |
| broadMauTranslationFreq OBJECT-TYPE ********* THIS OBJECT IS DEPRECATED ********** This variable indicates the translation offset frequency of the 10BROAD36 MAU in MHz/4; that is, in units of 250 kHz. | 1.3.6.1.2.1.26.3.1.1.5 | Integer32 | read-only | deprecated |
| dot3IfMauAutoNegGroup OBJECT-IDENTITY | 1.3.6.1.2.1.26.5 | |||
| ifMauAutoNegTable OBJECT-TYPE Configuration and status objects for the auto-negotiation function of MAUs attached to interfaces. The ifMauAutoNegTable applies to systems in which auto-negotiation is supported on one or more MAUs attached to interfaces. Note that if auto-negotiation is present and enabled, the ifMauType object reflects the result of the auto-negotiation function. | 1.3.6.1.2.1.26.5.1 | not-accessible | current | |
| ifMauAutoNegEntry OBJECT-TYPE An entry in the table, containing configuration and status information for the auto-negotiation function of a particular MAU. | 1.3.6.1.2.1.26.5.1.1 | not-accessible | current | |
| ifMauAutoNegAdminStatus OBJECT-TYPE Setting this object to enabled(1) will cause the interface that has the auto-negotiation signaling ability to be enabled. If the value of this object is disabled(2) then the interface will act as it would if it had no auto-negotiation signaling. Under these conditions, an IEEE 802.3 MAU will immediately be forced to the state indicated by the value of the object ifMauDefaultType. NOTE TO IMPLEMENTORS: When ifMauAutoNegAdminStatus transitions from enabled to disabled, the agent implementation MUST ensure that the operational type of the MAU (as reported by ifMauType) correctly transitions to the value specified by the ifMauDefaultType object, rather than continuing to operate at the value earlier determined by the auto-negotiation function. | 1.3.6.1.2.1.26.5.1.1.1 | INTEGER {enabled(1), disabled(2)} | read-write | current |
| ifMauAutoNegRemoteSignaling OBJECT-TYPE A value indicating whether the remote end of the link is using auto-negotiation signaling. It takes the value detected(1) if and only if, during the previous link negotiation, FLP Bursts were received. | 1.3.6.1.2.1.26.5.1.1.2 | INTEGER {detected(1), notdetected(2)} | read-only | current |
| ifMauAutoNegConfig OBJECT-TYPE A value indicating the current status of the auto-negotiation process. The enumeration parallelDetectFail(5) maps to a failure in parallel detection as defined in 28.2.3.1 of [IEEE802.3]. | 1.3.6.1.2.1.26.5.1.1.4 | INTEGER {other(1), configuring(2), complete(3), disabled(4), parallelDetectFail(5)} | read-only | current |
| ifMauAutoNegCapability OBJECT-TYPE ********* THIS OBJECT IS DEPRECATED ********** This object has been deprecated in favour of ifMauAutoNegCapabilityBits. A value that uniquely identifies the set of capabilities of the local auto-negotiation entity. The value is a sum that initially takes the value zero. Then, for each capability of this interface, 2 raised to the power noted below is added to the sum. For example, an interface that has the capability to support only 100Base-TX half duplex would have a value of 32768 (2**15). In contrast, an interface that supports both 100Base-TX half duplex and 100Base-TX full duplex would have a value of 98304 ((2**15) + (2**16)). The powers of 2 assigned to the capabilities are these: Power Capability 0 other or unknown (1-9) (reserved) 10 10BASE-T half duplex mode 11 10BASE-T full duplex mode 12 (reserved) 13 (reserved) 14 100BASE-T4 15 100BASE-TX half duplex mode 16 100BASE-TX full duplex mode 17 (reserved) 18 (reserved) 19 100BASE-T2 half duplex mode 20 100BASE-T2 full duplex mode Note that interfaces that support this MIB may have capabilities that extend beyond the scope of this MIB. | 1.3.6.1.2.1.26.5.1.1.5 | Integer32 | read-only | deprecated |
| ifMauAutoNegCapAdvertised OBJECT-TYPE ********* THIS OBJECT IS DEPRECATED ********** This object has been deprecated in favour of ifMauAutoNegCapAdvertisedBits. A value that uniquely identifies the set of capabilities advertised by the local auto-negotiation entity. Refer to ifMauAutoNegCapability for a description of the possible values of this object. Capabilities in this object that are not available in ifMauAutoNegCapability cannot be enabled. | 1.3.6.1.2.1.26.5.1.1.6 | Integer32 | read-write | deprecated |
| ifMauAutoNegCapReceived OBJECT-TYPE ********* THIS OBJECT IS DEPRECATED ********** This object has been deprecated in favour of ifMauAutoNegCapReceivedBits. A value that uniquely identifies the set of capabilities received from the remote auto-negotiation entity. Refer to ifMauAutoNegCapability for a description of the possible values of this object. Note that interfaces that support this MIB may be attached to remote auto-negotiation entities that have capabilities beyond the scope of this MIB. | 1.3.6.1.2.1.26.5.1.1.7 | Integer32 | read-only | deprecated |
| ifMauAutoNegRestart OBJECT-TYPE If the value of this object is set to restart(1) then this will force auto-negotiation to begin link renegotiation. If auto-negotiation signaling is disabled, a write to this object has no effect. Setting the value of this object to norestart(2) has no effect. | 1.3.6.1.2.1.26.5.1.1.8 | INTEGER {restart(1), norestart(2)} | read-write | current |
| ifMauAutoNegCapabilityBits OBJECT-TYPE A value that uniquely identifies the set of capabilities of the local auto-negotiation entity. Note that interfaces that support this MIB may have capabilities that extend beyond the scope of this MIB. Note that the local auto-negotiation entity may support some capabilities beyond the scope of this MIB. This is indicated by returning the bit value bOther in addition to any bit values for standard capabilities that are listed in the IANAifMauAutoNegCapBits TC. | 1.3.6.1.2.1.26.5.1.1.9 | IANAifMauAutoNegCapBits | read-only | current |
| ifMauAutoNegCapAdvertisedBits OBJECT-TYPE A value that uniquely identifies the set of capabilities advertised by the local auto-negotiation entity. Capabilities in this object that are not available in ifMauAutoNegCapabilityBits cannot be enabled. Note that the local auto-negotiation entity may advertise some capabilities beyond the scope of this MIB. This is indicated by returning the bit value bOther in addition to any bit values for standard capabilities that are listed in the IANAifMauAutoNegCapBits TC. | 1.3.6.1.2.1.26.5.1.1.10 | IANAifMauAutoNegCapBits | read-write | current |
| ifMauAutoNegCapReceivedBits OBJECT-TYPE A value that uniquely identifies the set of capabilities received from the remote auto-negotiation entity. Note that interfaces that support this MIB may be attached to remote auto-negotiation entities that have capabilities beyond the scope of this MIB. This is indicated by returning the bit value bOther in addition to any bit values for standard capabilities that are listed in the IANAifMauAutoNegCapBits TC. | 1.3.6.1.2.1.26.5.1.1.11 | IANAifMauAutoNegCapBits | read-only | current |
| ifMauAutoNegRemoteFaultAdvertised OBJECT-TYPE A value that identifies any local fault indications that this MAU has detected and will advertise at the next auto-negotiation interaction for 1000Mbps MAUs. | 1.3.6.1.2.1.26.5.1.1.12 | INTEGER {noError(1), offline(2), linkFailure(3), autoNegError(4)} | read-write | current |
| ifMauAutoNegRemoteFaultReceived OBJECT-TYPE A value that identifies any fault indications received from the far end of a link by the local auto-negotiation entity for 1000Mbps MAUs. | 1.3.6.1.2.1.26.5.1.1.13 | INTEGER {noError(1), offline(2), linkFailure(3), autoNegError(4)} | read-only | current |
| mauModConf OBJECT-IDENTITY | 1.3.6.1.2.1.26.6.1 | |||
| mauModCompls OBJECT-IDENTITY | 1.3.6.1.2.1.26.6.1.1 | |||
| mauModObjGrps OBJECT-IDENTITY | 1.3.6.1.2.1.26.6.1.2 | |||
| mauModNotGrps OBJECT-IDENTITY | 1.3.6.1.2.1.26.6.1.3 |
Notifications
| Name | OID | Status |
|---|---|---|
| rpMauJabberTrap NOTIFICATION-TYPE This trap is sent whenever a managed repeater MAU enters the jabber state. The agent MUST throttle the generation of consecutive rpMauJabberTraps so that there is at least a five-second gap between them. | 1.3.6.1.2.1.26.0.1 | current |
| ifMauJabberTrap NOTIFICATION-TYPE This trap is sent whenever a managed interface MAU enters the jabber state. The agent MUST throttle the generation of consecutive ifMauJabberTraps so that there is at least a five-second gap between them. | 1.3.6.1.2.1.26.0.2 | current |
Conformance
| Name | OID | Status |
|---|---|---|
| mauModRpCompl MODULE-COMPLIANCE ******** THIS COMPLIANCE IS DEPRECATED ******** Compliance for MAUs attached to repeater ports. This compliance is deprecated and replaced by mauModRpCompl2, which corrects an oversight by allowing rpMauStatus to be implemented read-only. | 1.3.6.1.2.1.26.6.1.1.1 | deprecated |
| mauModIfCompl MODULE-COMPLIANCE ******** THIS COMPLIANCE IS DEPRECATED ******** Compliance for MAUs attached to interfaces. This compliance is deprecated and replaced by mauModIfCompl2. | 1.3.6.1.2.1.26.6.1.1.2 | deprecated |
| mauModIfCompl2 MODULE-COMPLIANCE ******** THIS COMPLIANCE IS DEPRECATED ******** Compliance for MAUs attached to interfaces. This compliance is deprecated and replaced by mauModIfCompl3. | 1.3.6.1.2.1.26.6.1.1.3 | deprecated |
| mauModRpCompl2 MODULE-COMPLIANCE Compliance for MAUs attached to repeater ports. Note that compliance with this compliance statement requires compliance with the snmpRptrModCompl MODULE-COMPLIANCE statement of the SNMP-REPEATER-MIB (RFC 2108). | 1.3.6.1.2.1.26.6.1.1.4 | current |
| mauModIfCompl3 MODULE-COMPLIANCE Compliance for MAUs attached to interfaces. Note that compliance with this compliance statement requires compliance with the ifCompliance3 MODULE-COMPLIANCE statement of the IF-MIB (RFC 2863) and the dot3Compliance2 MODULE-COMPLIANCE statement of the EtherLike-MIB (RFC3635). | 1.3.6.1.2.1.26.6.1.1.5 | current |
| mauRpGrpBasic OBJECT-GROUP Basic conformance group for MAUs attached to repeater ports. This group is also the conformance specification for RFC 1515 implementations. | 1.3.6.1.2.1.26.6.1.2.1 | current |
| mauRpGrp100Mbs OBJECT-GROUP Conformance group for MAUs attached to repeater ports with 100 Mb/s or greater capability. | 1.3.6.1.2.1.26.6.1.2.2 | current |
| mauRpGrpJack OBJECT-GROUP Conformance group for MAUs attached to repeater ports with managed jacks. | 1.3.6.1.2.1.26.6.1.2.3 | current |
| mauIfGrpBasic OBJECT-GROUP Basic conformance group for MAUs attached to interfaces. This group also provides a conformance specification for RFC 1515 implementations. | 1.3.6.1.2.1.26.6.1.2.4 | current |
| mauIfGrp100Mbs OBJECT-GROUP ********* THIS GROUP IS DEPRECATED ********** Conformance group for MAUs attached to interfaces with 100 Mb/s capability. This object group has been deprecated in favor of mauIfGrpHighCapacity. | 1.3.6.1.2.1.26.6.1.2.5 | deprecated |
| mauIfGrpJack OBJECT-GROUP Conformance group for MAUs attached to interfaces with managed jacks. | 1.3.6.1.2.1.26.6.1.2.6 | current |
| mauIfGrpAutoNeg OBJECT-GROUP ********* THIS GROUP IS DEPRECATED ********** Conformance group for MAUs attached to interfaces with managed auto-negotiation. This object group has been deprecated in favor of mauIfGrpAutoNeg2. | 1.3.6.1.2.1.26.6.1.2.7 | deprecated |
| mauBroadBasic OBJECT-GROUP ********* THIS GROUP IS DEPRECATED ********** Conformance group for broadband MAUs attached to interfaces. This object group is deprecated. There have been no reported implementations of this group, and it was felt to be unlikely that there will be any future implementations. | 1.3.6.1.2.1.26.6.1.2.8 | deprecated |
| mauIfGrpHighCapacity OBJECT-GROUP Conformance group for MAUs attached to interfaces with 100 Mb/s or greater capability. | 1.3.6.1.2.1.26.6.1.2.9 | current |
| mauIfGrpAutoNeg2 OBJECT-GROUP Conformance group for MAUs attached to interfaces with managed auto-negotiation. | 1.3.6.1.2.1.26.6.1.2.10 | current |
| mauIfGrpAutoNeg1000Mbps OBJECT-GROUP Conformance group for 1000Mbps MAUs attached to interfaces with managed auto-negotiation. | 1.3.6.1.2.1.26.6.1.2.11 | current |
| mauIfGrpHCStats OBJECT-GROUP Conformance for high capacity statistics for MAUs attached to interfaces. | 1.3.6.1.2.1.26.6.1.2.12 | current |
| rpMauNotifications NOTIFICATION-GROUP Notifications for repeater MAUs. | 1.3.6.1.2.1.26.6.1.3.1 | current |
| ifMauNotifications NOTIFICATION-GROUP Notifications for interface MAUs. | 1.3.6.1.2.1.26.6.1.3.2 | current |