MIBs Depot

IPADv2-MIB

Registered at
1.3.6.1.4.1.321.100.1
Last updated
1900-11-21 00:00
Organization
Verilink Corporation
Namespace
zhone
Source file
IPADv2-MIB
Digest
sha256:129d4a75cdd8a7d7d37af0644b14c19fa1a7f6387a6f7a5716c2f5c92b91adcd

Description

IPADv2.MIB updated for SNMPv2.

Contact

support@verilink.com + 1 800 285 2755

Imports

FromSymbols
DS8200v2-MIBddsNetBPVCount, ddsNetFDLCount, ddsNetLOSCount, ddsNetOOFCount, ddsNetOOSCount, serialDteDTRAlarmStatus, t1e1AISCount, t1e1BPVSCount, t1e1CSSCount, t1e1ESCount, t1e1LOSSCount, t1e1OOFSCount, t1e1RASCount, t1e1SESCount, t1e1UASCount
DS8200v2-TC-MIBhbu, verilink
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP
SNMPv2-SMIIpAddress, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, enterprises, iso
SNMPv2-TCDisplayString, TEXTUAL-CONVENTION

Imported by

6 module(s) in this corpus import this one.

Load order

Every file a consumer needs in order to load this module, dependencies first.

DS8200v2-MIB
DS8200v2-TC-MIB
IPADv2-MIB
SNMPv2-CONF
SNMPv2-SMI
SNMPv2-TC

Under this module's arcs

Where the registration tree carries on below this module.

ArcNameModule
1.3.6.1.4.1.321.100.1.7ipadPPP
1.3.6.1.4.1.321.100.1.13ipadRouterIPAD-ROUTER-MIB
1.3.6.1.4.1.321.100.1.25ipadAtmIPAD-ATM-MIB
1.3.6.1.4.1.321.100.1.26ipadNatIPAD-NAT-MIB
1.3.6.1.4.1.321.100.1.27ipadDhcpIPAD-DHCP-MIB
1.3.6.1.4.1.321.100.1.28ipadBridgeIPAD-BRIDGE-MIB

Objects

NameOIDSyntaxAccessStatus
ipadFrPort
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.1.1
ipadFrPortTable
OBJECT-TYPE
Table of frame relay port parameters.
1.3.6.1.4.1.321.100.1.1.1not-accessiblecurrent
ipadFrPortTableEntry
OBJECT-TYPE
An entry in the ipad frame relay port table.
1.3.6.1.4.1.321.100.1.1.1.1not-accessiblecurrent
ipadFrPortService
OBJECT-TYPE
Index into the ipad frame relay port table; an entry in the ipad service table.
1.3.6.1.4.1.321.100.1.1.1.1.1INTEGERread-onlycurrent
ipadFrPortActive
OBJECT-TYPE
Specifies if the port is active.
1.3.6.1.4.1.321.100.1.1.1.1.2INTEGER {other(1), no(2), yes(3)}read-onlycurrent
ipadFrPortLMIType
OBJECT-TYPE
Specifies the link management information type used on this port.
1.3.6.1.4.1.321.100.1.1.1.1.3INTEGER {other(1), ccitt(2), ansi(3), lmi(4), none(5)}read-onlycurrent
ipadFrPortLMIMode
OBJECT-TYPE
Specifies the link management information mode used on this port.
1.3.6.1.4.1.321.100.1.1.1.1.4INTEGER {other(1), sourcing(2), monitoring(3)}read-onlycurrent
ipadFrPortRxInvAlmThreshold
OBJECT-TYPE
Sets the rx invalid frames alarm threshold. Setting this field to 0 disables the alarm.
1.3.6.1.4.1.321.100.1.1.1.1.5INTEGERread-writecurrent
ipadFrPortRxInvAlmAlarm
OBJECT-TYPE
Reports if the invalid frames threshold has been exceeded.
1.3.6.1.4.1.321.100.1.1.1.1.6INTEGER {other(1), noAlarm(2), thresholdExceeded(3)}read-onlycurrent
ipadFrPortTxAlmThreshold
OBJECT-TYPE
Sets the tx throughput alarm threshold (in bits/second). Setting this field to 0 disables the alarm.
1.3.6.1.4.1.321.100.1.1.1.1.7INTEGERread-writecurrent
ipadFrPortTxAlmAlarm
OBJECT-TYPE
Reports if the tx throughput threshold has been exceeded.
1.3.6.1.4.1.321.100.1.1.1.1.8INTEGER {other(1), noAlarm(2), thresholdExceeded(3)}read-onlycurrent
ipadFrPortRxAlmThreshold
OBJECT-TYPE
Sets the rx throughput alarm threshold (in bits/second). Setting this field to 0 disables the alarm.
1.3.6.1.4.1.321.100.1.1.1.1.9INTEGERread-writecurrent
ipadFrPortRxAlmAlarm
OBJECT-TYPE
Reports if the rx throughput threshold has been exceeded.
1.3.6.1.4.1.321.100.1.1.1.1.10INTEGER {other(1), noAlarm(2), thresholdExceeded(3)}read-onlycurrent
ipadFrPortAlarmReset
OBJECT-TYPE
This is used to clear the current alarm counts.
1.3.6.1.4.1.321.100.1.1.1.1.11INTEGER {frPortAlarmResetOther(1), frPortAlarmResetClearAlarms(2), frPortAlarmResetClearStats(3)}read-writecurrent
ipadService
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.1.2
ipadServiceTable
OBJECT-TYPE
The ipad service table.
1.3.6.1.4.1.321.100.1.2.1not-accessiblecurrent
ipadServiceTableEntry
OBJECT-TYPE
An entry in the ipad service table.
1.3.6.1.4.1.321.100.1.2.1.1not-accessiblecurrent
ipadServiceIndex
OBJECT-TYPE
The index for the ipad service table.
1.3.6.1.4.1.321.100.1.2.1.1.1INTEGERread-onlycurrent
ipadServiceifIndex
OBJECT-TYPE
The MIB-II ifIndex for this service.
1.3.6.1.4.1.321.100.1.2.1.1.2INTEGER {disabled(0), supervisor(1), network1(2), network2(3), user1(4), user2(5), ethernet(6), auxiliary(7), network3(8), atmCES(9), modem(10), virtual(100)}read-writecurrent
ipadServiceType
OBJECT-TYPE
The type of this service.
1.3.6.1.4.1.321.100.1.2.1.1.3INTEGER {other(1), tdm(2), ppp(3), pppMonitor(4), frameRelay(5), frameRelayMonitor(6), ip(7), serial(8), tty(9), scada(10), parallelIO(11), atm(12), hdlcPPP(13), atmCES(14), modem(15)}read-writecurrent
ipadServicePair
OBJECT-TYPE
An entry in this table, which establishes a service pairing.
1.3.6.1.4.1.321.100.1.2.1.1.4INTEGERread-writecurrent
ipadServiceStatus
OBJECT-TYPE
This parameter indicates the status of the service. idle - The service is not doing anything or has not been configured for use. down - The physical layer for the service is not ready. training - The physical layer is not ready but is attempting to come up. connecting - The physical layer is not ready but is attempting to come up. physicalUp - The physical layer is ready the service is not ready. protocolUp - The service is able to pass data. dead - The service is inactive because no resources are available to support it. changed - Service parameters were changed and require a save and restart to take effect.
1.3.6.1.4.1.321.100.1.2.1.1.5INTEGER {other(1), idle(2), down(3), physicalUp(4), protocolUp(5), dead(6), changed(7), training(8), connecting(9)}read-onlycurrent
ipadServiceAddService
OBJECT-TYPE
Adds a row to the Service Table.
1.3.6.1.4.1.321.100.1.2.2INTEGER {addService(1)}read-writecurrent
ipadServiceDeleteService
OBJECT-TYPE
Identifies a Service to be deleted; an index into the Service Table.
1.3.6.1.4.1.321.100.1.2.3INTEGERread-writecurrent
ipadChannel
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.1.3
ipadChannelTable
OBJECT-TYPE
The ipad channel table.
1.3.6.1.4.1.321.100.1.3.1not-accessiblecurrent
ipadChannelTableEntry
OBJECT-TYPE
An entry in the ipad channel table.
1.3.6.1.4.1.321.100.1.3.1.1not-accessiblecurrent
ipadChannelifIndex
OBJECT-TYPE
Primary index into ipad channel table, MIB-II ifIndex.
1.3.6.1.4.1.321.100.1.3.1.1.1INTEGERread-onlycurrent
ipadChannelIndex
OBJECT-TYPE
Channel index for the physical interface.
1.3.6.1.4.1.321.100.1.3.1.1.2INTEGERread-onlycurrent
ipadChannelService
OBJECT-TYPE
Index into service table for this channel.
1.3.6.1.4.1.321.100.1.3.1.1.3INTEGERread-writecurrent
ipadChannelPair
OBJECT-TYPE
Pair for this channel; an entry in the channel table. Use service pair in service table to determine which service contains this channel.
1.3.6.1.4.1.321.100.1.3.1.1.4INTEGERread-writecurrent
ipadChannelRate
OBJECT-TYPE
Rate for this channel.
1.3.6.1.4.1.321.100.1.3.1.1.5INTEGER {other(1), rate56(2), rate64(3), rate8(4)}read-writecurrent
ipadChannelIdlePattern
OBJECT-TYPE
Idle pattern for this channel.
1.3.6.1.4.1.321.100.1.3.1.1.6INTEGERread-onlycurrent
ipadDLCI
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.1.4
ipadDLCITable
OBJECT-TYPE
The ipad DLCI table.
1.3.6.1.4.1.321.100.1.4.1not-accessiblecurrent
ipadDLCITableEntry
OBJECT-TYPE
An entry in the ipad DLCI table.
1.3.6.1.4.1.321.100.1.4.1.1not-accessiblecurrent
ipadDLCIservice
OBJECT-TYPE
An index into the ipad service table.
1.3.6.1.4.1.321.100.1.4.1.1.1INTEGERread-onlycurrent
ipadDLCInumber
OBJECT-TYPE
The DLCI number for this entry.
1.3.6.1.4.1.321.100.1.4.1.1.2INTEGERread-onlycurrent
ipadDLCIactive
OBJECT-TYPE
Specifies if the DLCI is active.
1.3.6.1.4.1.321.100.1.4.1.1.3INTEGER {other(1), no(2), yes(3), pending(4)}read-onlycurrent
ipadDLCIcongestion
OBJECT-TYPE
Specifies if the dlci is receiving frames with FECN or BECN bit set.
1.3.6.1.4.1.321.100.1.4.1.1.4INTEGER {other(1), no(2), yes(3)}read-onlycurrent
ipadDLCIremote
OBJECT-TYPE
Remote DLCI number.
1.3.6.1.4.1.321.100.1.4.1.1.5INTEGERread-onlycurrent
ipadDLCIremoteUnit
OBJECT-TYPE
Name of the remote DLCI.
1.3.6.1.4.1.321.100.1.4.1.1.6DisplayString (SIZE(0..11))read-onlycurrent
ipadDLCIremoteEquipActive
OBJECT-TYPE
Reports if the equipment attached to the remote unit is active.
1.3.6.1.4.1.321.100.1.4.1.1.7INTEGER {other(1), inactive(2), active(3), sosAlarm(4)}read-onlycurrent
ipadDLCIencapsulation
OBJECT-TYPE
Type of protocol encapsulation used on this DLCI.
1.3.6.1.4.1.321.100.1.4.1.1.8INTEGER {other(1), rfc1490(2), proprietary(3), rfc1490withEncryption(4), rfc1490withCompression(5)}read-writecurrent
ipadDLCIproprietary
OBJECT-TYPE
When the encapsulation is proprietary, the traffic type must be configured to gather protocol specific statistics.
1.3.6.1.4.1.321.100.1.4.1.1.9INTEGER {other(1), ip(2), ipx(3), ethertype(4), none(5)}read-writecurrent
ipadDLCIpropOffset
OBJECT-TYPE
When the encapsulation is proprietary, this is the number of bytes after the frame relay header to look for the specified protocol decode.
1.3.6.1.4.1.321.100.1.4.1.1.10INTEGERread-writecurrent
ipadDLCIinBand
OBJECT-TYPE
Determines if frames on this DLCI will be parsed to look for management frames destined for the unit itself.
1.3.6.1.4.1.321.100.1.4.1.1.11INTEGER {other(1), no(2), yes(3)}read-writecurrent
ipadDLCICIR
OBJECT-TYPE
Default committed information rate in bits per second.
1.3.6.1.4.1.321.100.1.4.1.1.12INTEGERread-writecurrent
ipadDLCIBe
OBJECT-TYPE
Default excess burst rate in bits per second.
1.3.6.1.4.1.321.100.1.4.1.1.13INTEGERread-writecurrent
ipadDLCIminBC
OBJECT-TYPE
If the corresponding interface is configured to enable congestion management, the minimum transfer rate at which the unit will throttle back offering data to the network.
1.3.6.1.4.1.321.100.1.4.1.1.14INTEGERread-writecurrent
ipadDLCIrxMon
OBJECT-TYPE
Determines if the SLA parameters will be monitored for received frames.
1.3.6.1.4.1.321.100.1.4.1.1.15INTEGER {other(1), no(2), yes(3)}read-writecurrent
ipadDLCIdEctrl
OBJECT-TYPE
Determines if the Rx monitor will set the DE bit on all frames received in excess of the CIR before they are switched to their destination port.
1.3.6.1.4.1.321.100.1.4.1.1.16INTEGER {other(1), no(2), yes(3)}read-writecurrent
ipadDLCIenableDelay
OBJECT-TYPE
Enable or disable delay.
1.3.6.1.4.1.321.100.1.4.1.1.17INTEGER {other(1), disable(2), enable(3)}read-writecurrent
ipadDLCItxExCIRThreshold
OBJECT-TYPE
Sets the Tx over CIR alarm threshold. This threshold is the number of bits per second in excess of CIR. Setting this field to 0 disables the alarm.
1.3.6.1.4.1.321.100.1.4.1.1.18INTEGERread-writecurrent
ipadDLCItxExCIRAlarm
OBJECT-TYPE
Reports if the Tx over CIR threshold has been exceeded.
1.3.6.1.4.1.321.100.1.4.1.1.19INTEGER {other(1), noAlarm(2), thresholdExceeded(3)}read-onlycurrent
ipadDLCItxExBeThreshold
OBJECT-TYPE
Sets the Tx over Be alarm threshold. This threshold is the number of bits per second in excess of Be. Setting this field to 0 disables the alarm.
1.3.6.1.4.1.321.100.1.4.1.1.20INTEGERread-writecurrent
ipadDLCItxExBeAlarm
OBJECT-TYPE
Reports if the Tx over Be threshold has been exceeded.
1.3.6.1.4.1.321.100.1.4.1.1.21INTEGER {other(1), noAlarm(2), thresholdExceeded(3)}read-onlycurrent
ipadDLCIrxCongThreshold
OBJECT-TYPE
Sets the Rx congestion alarm threshold. This threshold is the number of frames received with BECN/FECN. Setting this field to 0 disables the alarm.
1.3.6.1.4.1.321.100.1.4.1.1.22INTEGERread-writecurrent
ipadDLCIrxCongAlarm
OBJECT-TYPE
Reports if the Rx congestion threshold has been exceeded.
1.3.6.1.4.1.321.100.1.4.1.1.23INTEGER {other(1), noAlarm(2), thresholdExceeded(3)}read-onlycurrent
ipadDLCIrxBECNinCIR
OBJECT-TYPE
Reports if BECN has been received within CIR.
1.3.6.1.4.1.321.100.1.4.1.1.24INTEGER {other(1), noAlarm(2), alarmCondition(3)}read-onlycurrent
ipadDLCIUASThreshold
OBJECT-TYPE
Sets the UAS (unavailable seconds) alarm threshold. This threshold is the number of seconds passed that the DLCI is unavailable. Setting this field to 0 disables the alarm.
1.3.6.1.4.1.321.100.1.4.1.1.25INTEGERread-writecurrent
ipadDLCIUASAlarm
OBJECT-TYPE
Reports if the UAS threshold has been exceeded.
1.3.6.1.4.1.321.100.1.4.1.1.26INTEGER {other(1), noAlarm(2), thresholdExceeded(3)}read-onlycurrent
ipadDLCIAlarmReset
OBJECT-TYPE
This is used to clear the current alarm counts.
1.3.6.1.4.1.321.100.1.4.1.1.27INTEGER {dlciAlarmResetOther(1), dlciAlarmResetClearAlarms(2), dlciAlarmResetClearStats(3)}read-writecurrent
ipadDLCIRoundTripDelaySize
OBJECT-TYPE
Specifies the packet size in octets used to calculate round trip delay.
1.3.6.1.4.1.321.100.1.4.1.1.28INTEGER (16..1500)read-writecurrent
ipadDLCIRoundTripDelayRate
OBJECT-TYPE
Specifies the packet rate in seconds used to calculate round trip delay.
1.3.6.1.4.1.321.100.1.4.1.1.29INTEGER (1..900)read-writecurrent
ipadDLCIRemoteFramesOfferedWithinCIR
OBJECT-TYPE
Count of frames sent within CIR from the remote end of the DLCI.
1.3.6.1.4.1.321.100.1.4.1.1.30INTEGERread-onlycurrent
ipadDLCIRemoteFramesOfferedWithinBE
OBJECT-TYPE
Count of frames sent within BE, but over CIR, from the remote end of the DLCI.
1.3.6.1.4.1.321.100.1.4.1.1.31INTEGERread-onlycurrent
ipadDLCIFramesReceived
OBJECT-TYPE
Count of frames received by the local device on this DLCI.
1.3.6.1.4.1.321.100.1.4.1.1.32INTEGERread-onlycurrent
ipadDLCIRemoteDataOfferedWithinCIR
OBJECT-TYPE
Count of data octets sent within CIR from the remote end of the DLCI.
1.3.6.1.4.1.321.100.1.4.1.1.33INTEGERread-onlycurrent
ipadDLCIRemoteDataOfferedWithinBE
OBJECT-TYPE
Count of data octets sent within BE, but over CIR, from the remote end of the DLCI.
1.3.6.1.4.1.321.100.1.4.1.1.34INTEGERread-onlycurrent
ipadDLCIDataReceived
OBJECT-TYPE
Count of data octets received by the local device on this DLCI.
1.3.6.1.4.1.321.100.1.4.1.1.35INTEGERread-onlycurrent
ipadDLCIRemoteIPAddress
OBJECT-TYPE
The IP Address of the device on the remote end of this DLCI. This information is only valid when the remote device supports Verilink's proprietary message exchange.
1.3.6.1.4.1.321.100.1.4.1.1.36IpAddressread-onlycurrent
ipadDLCICompressionStatus
OBJECT-TYPE
This is the current status of the compression engine for this DLCI. disabled(2) indicates that the compression engine is disabled. enabledAndNegotiated(3) indicates that compression is enabled, and has been successfully negotiated with the device at the other end. enabledButNotNegotiated(4) indicated that compression is enabled, but has not been successfully negotiated with the device at the other end. This may be due to the DLCI being down, the other device not having compression enabled or other factors which would inhibit communication.
1.3.6.1.4.1.321.100.1.4.1.1.37INTEGER {other(1), disabled(2), enabledAndNegotiated(3), enabledButNotNegotiated(4)}read-onlycurrent
ipadDLCICompressionTxOctetsIn
OBJECT-TYPE
This is a rolling counter of the number of octets given to the compression engine.
1.3.6.1.4.1.321.100.1.4.1.1.38INTEGERread-onlycurrent
ipadDLCICompressionTxOctetsOut
OBJECT-TYPE
This is a rolling counter of the number of octets output from the compression engine.
1.3.6.1.4.1.321.100.1.4.1.1.39INTEGERread-onlycurrent
ipadDLCICompressionRxOctetsIn
OBJECT-TYPE
This is a rolling counter of the number of octets given to the compression engine.
1.3.6.1.4.1.321.100.1.4.1.1.40INTEGERread-onlycurrent
ipadDLCICompressionRxOctetsOut
OBJECT-TYPE
This is a rolling counter of the number of octets given to the compression engine.
1.3.6.1.4.1.321.100.1.4.1.1.41INTEGERread-onlycurrent
ipadDLCILastChange
OBJECT-TYPE
Time of the last change in the DLCI table.
1.3.6.1.4.1.321.100.1.4.2TimeTicksread-onlycurrent
ipadEndpoint
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.1.5
ipadEndpointTable
OBJECT-TYPE
The ipad endpoint table.
1.3.6.1.4.1.321.100.1.5.1not-accessiblecurrent
ipadEndpointTableEntry
OBJECT-TYPE
An entry in the ipad endpoint table.
1.3.6.1.4.1.321.100.1.5.1.1not-accessiblecurrent
ipadEndpointIndex
OBJECT-TYPE
The index into the ipad endpoint table.
1.3.6.1.4.1.321.100.1.5.1.1.1INTEGERread-onlycurrent
ipadEndpointName
OBJECT-TYPE
The name for the endpoint.
1.3.6.1.4.1.321.100.1.5.1.1.2DisplayString (SIZE(0..11))read-writecurrent
ipadEndpointService
OBJECT-TYPE
An index into the ipad service table.
1.3.6.1.4.1.321.100.1.5.1.1.3INTEGERread-writecurrent
ipadEndpointDLCInumber
OBJECT-TYPE
Data link connection identifier for this endpoint; The DLCI number for this entry.
1.3.6.1.4.1.321.100.1.5.1.1.4INTEGERread-writecurrent
ipadEndpointType
OBJECT-TYPE
Endpoint type.
1.3.6.1.4.1.321.100.1.5.1.1.5INTEGER {other(1), frLocal(2), frSwitched(3), ipRoute(4)}read-writecurrent
ipadEndpointForward
OBJECT-TYPE
Index into the endpoint names table. This is the endpoint on which data should be forwarded for switched endpoints.
1.3.6.1.4.1.321.100.1.5.1.1.6INTEGERread-writecurrent
ipadEndpointBackup
OBJECT-TYPE
Index into the endpoint table. This is the endpoint on which data should be forwarded in the case where the endpoint becomes inactive.
1.3.6.1.4.1.321.100.1.5.1.1.7INTEGERread-writecurrent
ipadEndpointRefSLP
OBJECT-TYPE
Index into the endpoint table. The service level parameters can be copied from another configured endpoint.
1.3.6.1.4.1.321.100.1.5.1.1.8INTEGERread-writecurrent
ipadEndpointRemoteIpAddr
OBJECT-TYPE
IP address for remote.
1.3.6.1.4.1.321.100.1.5.1.1.9IpAddressread-writecurrent
ipadEndpointRemoteIpMask
OBJECT-TYPE
IP address mask for remote.
1.3.6.1.4.1.321.100.1.5.1.1.10IpAddressread-writecurrent
ipadEndpointAddEndpoint
OBJECT-TYPE
Identifies an Endpoint to be added.
1.3.6.1.4.1.321.100.1.5.2DisplayString (SIZE(0..11))read-writecurrent
ipadEndpointDeleteEndpoint
OBJECT-TYPE
Identifies an Endpoint to be deleted.
1.3.6.1.4.1.321.100.1.5.3DisplayString (SIZE(0..11))read-writecurrent
ipadEndpointLastChange
OBJECT-TYPE
Time of the last change in the Endpoint table.
1.3.6.1.4.1.321.100.1.5.4TimeTicksread-onlycurrent
ipadUser
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.1.6
ipadUserTable
OBJECT-TYPE
Table of user selected parameters.
1.3.6.1.4.1.321.100.1.6.1not-accessiblecurrent
ipadUserTableEntry
OBJECT-TYPE
An entry in the ipad user table.
1.3.6.1.4.1.321.100.1.6.1.1not-accessiblecurrent
ipadUserIndex
OBJECT-TYPE
Index into the ipad user table.
1.3.6.1.4.1.321.100.1.6.1.1.1INTEGERread-onlycurrent
ipadUserFilterByDLCI
OBJECT-TYPE
Enables Service+DLCI filtering for this user statistic.
1.3.6.1.4.1.321.100.1.6.1.1.2INTEGER {disabled(1), enabled(2)}read-writecurrent
ipadUserService
OBJECT-TYPE
Specifies the service for this user type; identifies an entry in the ipad DLCI table when combined with ipadUserDLCI. Meaningful when ipadUserFilterByDLCI is enabled. Meaningless when collecting PPP statistics.
1.3.6.1.4.1.321.100.1.6.1.1.3INTEGERread-writecurrent
ipadUserDLCI
OBJECT-TYPE
Specifies the DLCI for this user type; identifies an entry in the ipad DLCI table when combined with ipadUserService. Meaningful when ipadUserFilterByDLCI is enabled. Meaningless when collecting PPP statistics.
1.3.6.1.4.1.321.100.1.6.1.1.4INTEGERread-writecurrent
ipadUserFilterByIPAddress
OBJECT-TYPE
Enables IP address filtering for this user statistic. A packet is counted towards the user statistics if the result of a bitwise-and of an IP address in a transmitted packet with ipadUserIPMask equals ipadUserIPAddress.
1.3.6.1.4.1.321.100.1.6.1.1.5INTEGER {disabled(1), enabled(2)}read-writecurrent
ipadUserIPAddress
OBJECT-TYPE
Specifies the IP address for this user type.
1.3.6.1.4.1.321.100.1.6.1.1.6IpAddressread-writecurrent
ipadUserIPMask
OBJECT-TYPE
Specifies the IP address mask for this user type.
1.3.6.1.4.1.321.100.1.6.1.1.7IpAddressread-writecurrent
ipadUserFilterByIPPort
OBJECT-TYPE
Enables IP Port filtering for this user statistic.
1.3.6.1.4.1.321.100.1.6.1.1.8INTEGER {disabled(1), enabled(2)}read-writecurrent
ipadUserIPPort
OBJECT-TYPE
Specifies the IP port for this user type.
1.3.6.1.4.1.321.100.1.6.1.1.9INTEGER {rje(5), echo(7), systat(11), qotd(17), ftpdata(20), ftp(21), telnet(23), smtp(25), msgauth(31), time(37), nameserver(42), domain(53), sqlnet(66), tftp(69), gopher(70), finger(79), http(80), kerberos(88), npp(92), hostname(101), rtelnet(107), pop2(109), pop3(110), sunrpc(111), auth(113), nntp(119), netbiosns(137), netbiosdgm(138), netbiosssn(139), sgmp(153), snmp(161), snmptrap(162), cmipman(163), cmipagent(164), send(169), bgp(179), irc(194), atrtmp(201), atnbp(202), atecho(204), atzis(206), ipx(213), netcp(395), netwareip(396), snpp(444), povray(494), netwall(533), uucp(540), uucprlogin(541), ipcserver(600), kerberosadm(749)}read-writecurrent
ipadUserTxAlmThreshold
OBJECT-TYPE
Sets the tx throughput alarm threshold in bits per second. Setting this field to 0 disables the alarm.
1.3.6.1.4.1.321.100.1.6.1.1.10INTEGERread-writecurrent
ipadUserTxAlmAlarm
OBJECT-TYPE
Reports if the tx throughput threshold has been exceeded.
1.3.6.1.4.1.321.100.1.6.1.1.11INTEGER {other(1), noAlarm(2), thresholdExceeded(3)}read-onlycurrent
ipadUserAlarmReset
OBJECT-TYPE
This is used to clear the current alarm counts.
1.3.6.1.4.1.321.100.1.6.1.1.12INTEGER {userAlarmResetOther(1), userAlarmResetClearAlarms(2), userAlarmResetClearStats(3)}read-writecurrent
ipadUserVpi
OBJECT-TYPE
Specifies the Vpi for this user type; identifies a VC when combined with the ipadUserService and ipadUserVci objects. Meaningful when ipadUserFilterByVpiVci is enabled. Meaningless when collecting PPP or Frame Relay statistics.
1.3.6.1.4.1.321.100.1.6.1.1.13INTEGERread-writecurrent
ipadUserVci
OBJECT-TYPE
Specifies the Vci for this user type; identifies a VC when combined with the ipadUserService and ipadUserVpi objects. Meaningful when ipadUserFilterByVpiVci is enabled. Meaningless when collecting PPP or Frame Relay statistics.
1.3.6.1.4.1.321.100.1.6.1.1.14INTEGERread-writecurrent
ipadUserFilterByVpiVci
OBJECT-TYPE
Enables Vpi/Vci filtering for this user statistic. A packet is counted towards the user statistics if the packet is transmitted on the service/Vpi/Vci combindation specified by ipadUserService, ipadUserVpi, and ipadUserVci.
1.3.6.1.4.1.321.100.1.6.1.1.15INTEGER {disabled(1), enabled(2)}read-writecurrent
ipadUserIPStatTimeRemaining
OBJECT-TYPE
Specifies seconds until the next IP TopN report is generated.
1.3.6.1.4.1.321.100.1.6.2INTEGERread-writecurrent
ipadUserIPStatTimeDuration
OBJECT-TYPE
The value of TimeRemaining when TimeRemaining was last set. Indicates the number of seconds that the next IP TopN report will cover.
1.3.6.1.4.1.321.100.1.6.3INTEGERread-onlycurrent
ipadUserIPStatStartTime
OBJECT-TYPE
The value of SysUpTime when TimeRemaining was last set.
1.3.6.1.4.1.321.100.1.6.4TimeTicksread-onlycurrent
ipadUserIPStatRequestedReportSize
OBJECT-TYPE
Determines the requested maximum number of entries in the topN report.
1.3.6.1.4.1.321.100.1.6.5INTEGERread-writecurrent
ipadUserIPStatGrantedReportSize
OBJECT-TYPE
Determines the granted number of entries in the topN report. This is by definition less than or equal to requested report size.
1.3.6.1.4.1.321.100.1.6.6INTEGERread-onlycurrent
ipadUserIPStatReportNumber
OBJECT-TYPE
Specifies the number of reports that have been generated. This value resets to zero when the unit is restarted.
1.3.6.1.4.1.321.100.1.6.7INTEGERread-onlycurrent
ipadUserIPStatDiscardType
OBJECT-TYPE
The internal table used to track TopN statistics is finite in size. On the condition when the internal table is full and a new IP address is encountered, an element already existing in the table must be removed. This variable determines the manner of selection. Writing byTime(1) will cause the entry with the least recent frame to be discarded. That is, all other entries in the table will have transmitted or received at least one packet more recently. Writing byFrames(2) will select the entry with the fewest transmitted or received frames. Writing byOctets(3) will select the entry with the fewest transmitted or received octets. The default is byTime(1).
1.3.6.1.4.1.321.100.1.6.8INTEGER {byTime(1), byFrames(2), byOctets(3)}read-writecurrent
ipadPPP
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.1.7
ipadPPPCfgTable
OBJECT-TYPE
The ipad PPP configuration table.
1.3.6.1.4.1.321.100.1.7.1not-accessiblecurrent
ipadPPPCfgTableEntry
OBJECT-TYPE
An entry in the ipad PPP configuration table.
1.3.6.1.4.1.321.100.1.7.1.1not-accessiblecurrent
ipadPPPCfgService
OBJECT-TYPE
The index into the PPP configuration table; an entry in the ipad service table.
1.3.6.1.4.1.321.100.1.7.1.1.1INTEGERread-onlycurrent
ipadPPPCfgDialMode
OBJECT-TYPE
Determines the permancency of a communications connection.
1.3.6.1.4.1.321.100.1.7.1.1.2INTEGER {other(1), direct(2), dialup(3), demanddial(4)}read-writecurrent
ipadPPPCfgInactivityTimer
OBJECT-TYPE
Determines when a dial-up or demand-dial connection will be disconnected due to inactivity in both directions. When this parameter is set to zero then the timer is disabled.
1.3.6.1.4.1.321.100.1.7.1.1.3INTEGERread-writecurrent
ipadPPPCfgNegotiationInit
OBJECT-TYPE
Determines if the port waits for the other end to initiate parameter negotiations.
1.3.6.1.4.1.321.100.1.7.1.1.4INTEGER {other(1), no(2), yes(3)}read-writecurrent
ipadPPPCfgMRU
OBJECT-TYPE
The maximum receive unit the interface will accept. Valid values are in the range 128 - 4096, default is 1500.
1.3.6.1.4.1.321.100.1.7.1.1.5INTEGERread-writecurrent
ipadPPPCfgACCM
OBJECT-TYPE
Sets the async control character map used when generating async HDLC frames. Setting a bit in the map causes the corresponding character to be mapped for transparency.
1.3.6.1.4.1.321.100.1.7.1.1.6INTEGERread-writecurrent
ipadPPPCfgNegMRU
OBJECT-TYPE
Determines if MRU size is negotiated.
1.3.6.1.4.1.321.100.1.7.1.1.7INTEGER {other(1), no(2), yes(3)}read-writecurrent
ipadPPPCfgNegACCM
OBJECT-TYPE
Determines if ACCM is negotiated.
1.3.6.1.4.1.321.100.1.7.1.1.8INTEGER {other(1), no(2), yes(3)}read-writecurrent
ipadPPPCfgNegMagic
OBJECT-TYPE
Determines if the magic number is negotiated.
1.3.6.1.4.1.321.100.1.7.1.1.9INTEGER {other(1), no(2), yes(3)}read-writecurrent
ipadPPPCfgNegCompression
OBJECT-TYPE
Determines if the PPP protocol header compression is negotiated.
1.3.6.1.4.1.321.100.1.7.1.1.10INTEGER {other(1), no(2), yes(3)}read-writecurrent
ipadPPPCfgNegAddress
OBJECT-TYPE
Determines if the PPP HDLC header compression is negotiated.
1.3.6.1.4.1.321.100.1.7.1.1.11INTEGER {other(1), no(2), yes(3)}read-writecurrent
ipadPPPCfgNegPAP
OBJECT-TYPE
Determines if PAP is negotiated with the peer when a more secure authentication protocol is rejected.
1.3.6.1.4.1.321.100.1.7.1.1.12INTEGER {other(1), no(2), yes(3)}read-writecurrent
ipadPPPCfgNegCHAP
OBJECT-TYPE
Determines if CHAP is negotiated with the peer when a more secure authentication protocol is rejected.
1.3.6.1.4.1.321.100.1.7.1.1.13INTEGER {other(1), no(2), yes(3)}read-writecurrent
ipadPPPCfgAllowPAP
OBJECT-TYPE
Determines if PAP is allowed to be negotiated by the peer.
1.3.6.1.4.1.321.100.1.7.1.1.14INTEGER {other(1), no(2), yes(3)}read-writecurrent
ipadPPPCfgAllowCHAP
OBJECT-TYPE
Determines if CHAP is allowed to be negotiated by the peer.
1.3.6.1.4.1.321.100.1.7.1.1.15INTEGER {other(1), no(2), yes(3)}read-writecurrent
ipadPPPCfgPAPUsername
OBJECT-TYPE
Identification string to determine the user identity.
1.3.6.1.4.1.321.100.1.7.1.1.16DisplayString (SIZE(0..30))read-writecurrent
ipadPPPCfgPAPPassword
OBJECT-TYPE
Password string to validate the user identity.
1.3.6.1.4.1.321.100.1.7.1.1.17DisplayString (SIZE(0..30))read-writecurrent
ipadPPPCfgCHAPUsername
OBJECT-TYPE
Identification string to determine the user identity.
1.3.6.1.4.1.321.100.1.7.1.1.18DisplayString (SIZE(0..30))read-writecurrent
ipadPPPCfgCHAPSecret
OBJECT-TYPE
Password string to validate the user identity.
1.3.6.1.4.1.321.100.1.7.1.1.19DisplayString (SIZE(0..30))read-writecurrent
ipadPPPCfgPortIpAddress
OBJECT-TYPE
Sets the IP address of the unit's port.
1.3.6.1.4.1.321.100.1.7.1.1.20IpAddressread-writecurrent
ipadPPPCfgPeerIpAddress
OBJECT-TYPE
Sets the IP address of the unit's peer.
1.3.6.1.4.1.321.100.1.7.1.1.21IpAddressread-writecurrent
ipadPPPCfgNegIpAddress
OBJECT-TYPE
Determines if IP addresses are dynamically negotiated.
1.3.6.1.4.1.321.100.1.7.1.1.22INTEGER {other(1), no(2), yes(3)}read-writecurrent
ipadPPPCfgNegIPCPCompression
OBJECT-TYPE
Determines if Van Jacobson TCPIP header compression is negotiated.
1.3.6.1.4.1.321.100.1.7.1.1.23INTEGER {other(1), no(2), yes(3)}read-writecurrent
ipadPPPCfgSubnetMask
OBJECT-TYPE
Specifies the subnet mask.
1.3.6.1.4.1.321.100.1.7.1.1.24IpAddressread-writecurrent
ipadPPPCfgAuthChallengeInterval
OBJECT-TYPE
Specifies the authentication challenge interval.
1.3.6.1.4.1.321.100.1.7.1.1.25INTEGERread-writecurrent
ipadPPPCfgEndpoint
OBJECT-TYPE
Endpoint name to run PPP over another protocol.
1.3.6.1.4.1.321.100.1.7.1.1.26DisplayString (SIZE(0..11))read-writecurrent
ipadPPPCfgNegIpMask
OBJECT-TYPE
Determines if the subnet Mask is negotiated.
1.3.6.1.4.1.321.100.1.7.1.1.27INTEGER {other(1), no(2), yes(3)}read-writecurrent
ipadPPPCfgNegDNSAddress
OBJECT-TYPE
Determines if the DNS address is negotiated.
1.3.6.1.4.1.321.100.1.7.1.1.28INTEGER {other(1), no(2), yes(3)}read-writecurrent
ipadPPPPAPTable
OBJECT-TYPE
Table of PAP authentication parameters.
1.3.6.1.4.1.321.100.1.7.2not-accessiblecurrent
ipadPPPPAPTableEntry
OBJECT-TYPE
An entry in the ipad PPP PAP table.
1.3.6.1.4.1.321.100.1.7.2.1not-accessiblecurrent
ipadPPPPAPTableIndex
OBJECT-TYPE
The index into the PPP PAP association table.
1.3.6.1.4.1.321.100.1.7.2.1.1INTEGERread-onlycurrent
ipadPPPPAPTableUsername
OBJECT-TYPE
Identification string to identify the user.
1.3.6.1.4.1.321.100.1.7.2.1.2DisplayString (SIZE(0..30))read-writecurrent
ipadPPPPAPTablePassword
OBJECT-TYPE
Password string to validate the user identity.
1.3.6.1.4.1.321.100.1.7.2.1.3DisplayString (SIZE(0..30))read-writecurrent
ipadPPPCHAPTable
OBJECT-TYPE
Table of CHAP authentication parameters.
1.3.6.1.4.1.321.100.1.7.3not-accessiblecurrent
ipadPPPCHAPTableEntry
OBJECT-TYPE
An entry in the ipad PPP CHAP table.
1.3.6.1.4.1.321.100.1.7.3.1not-accessiblecurrent
ipadPPPCHAPTableIndex
OBJECT-TYPE
The index into the PPP CHAP association table.
1.3.6.1.4.1.321.100.1.7.3.1.1INTEGERread-onlycurrent
ipadPPPCHAPTableUsername
OBJECT-TYPE
Identification string to identify the user.
1.3.6.1.4.1.321.100.1.7.3.1.2DisplayString (SIZE(0..30))read-writecurrent
ipadPPPCHAPTableSecret
OBJECT-TYPE
Password string to validate the user identity.
1.3.6.1.4.1.321.100.1.7.3.1.3DisplayString (SIZE(0..30))read-writecurrent
ipadModem
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.1.8
ipadModemDialTable
OBJECT-TYPE
Table of modem dialing parameters.
1.3.6.1.4.1.321.100.1.8.1not-accessiblecurrent
ipadModemDialTableEntry
OBJECT-TYPE
An entry in the ipad modem dialing parameters table.
1.3.6.1.4.1.321.100.1.8.1.1not-accessiblecurrent
ipadModemDialTableIndex
OBJECT-TYPE
The index into the ipad modem dialing parameters table. Equivalent to MIB-II ifIndex.
1.3.6.1.4.1.321.100.1.8.1.1.1INTEGERread-onlycurrent
ipadModemDialDataIndex
OBJECT-TYPE
An index into the Modem Data Table, which selects a modem.
1.3.6.1.4.1.321.100.1.8.1.1.2INTEGERread-writecurrent
ipadModemDialNumber
OBJECT-TYPE
Specifies the telephone number to dial.
1.3.6.1.4.1.321.100.1.8.1.1.3DisplayString (SIZE(0..60))read-writecurrent
ipadModemDialAbortTimer
OBJECT-TYPE
Aborts a connection attempt if a dial-up connection has failed to connect within the specified number of seconds. Range is 1..255.
1.3.6.1.4.1.321.100.1.8.1.1.4INTEGERread-writecurrent
ipadModemDialRedialAttempts
OBJECT-TYPE
Determines how many attempts to initiate a dial-up connection after the initial failure. Range is 0..10.
1.3.6.1.4.1.321.100.1.8.1.1.5INTEGERread-writecurrent
ipadModemDialDelayBeforeRedial
OBJECT-TYPE
Specifies the number of seconds to wait before redialing. Range is 1..255.
1.3.6.1.4.1.321.100.1.8.1.1.6INTEGERread-writecurrent
ipadModemDialLoginScript
OBJECT-TYPE
Script string interpreted after an originated dial-up connection is first established.
1.3.6.1.4.1.321.100.1.8.1.1.7DisplayString (SIZE(0..60))read-writecurrent
ipadModemDialUsername
OBJECT-TYPE
Identification string to determine the user identity.
1.3.6.1.4.1.321.100.1.8.1.1.8DisplayString (SIZE(0..30))read-writecurrent
ipadModemDialPassword
OBJECT-TYPE
Password string to validate the user identity.
1.3.6.1.4.1.321.100.1.8.1.1.9DisplayString (SIZE(0..30))read-writecurrent
ipadModemDialChallengeScript
OBJECT-TYPE
Script string interpreted after an answered dial-up connection is first established.
1.3.6.1.4.1.321.100.1.8.1.1.10DisplayString (SIZE(0..60))read-writecurrent
ipadModemDialAnswerRings
OBJECT-TYPE
Answers an incoming call on the given number of rings. A value of zero disables answering. Range is 0..255.
1.3.6.1.4.1.321.100.1.8.1.1.11INTEGERread-writecurrent
ipadModemDialCommand
OBJECT-TYPE
The set values perform the following actions: setupNow - Execute the modem setup scripts dialNow - Initiate dialing procedures answerNow - Initiate answering procedures disconnectNow - Initiate disconnect procedures
1.3.6.1.4.1.321.100.1.8.1.1.12INTEGER {other(1), setupNow(2), dialNow(3), answerNow(4), disconnectNow(5)}read-writecurrent
ipadModemDialStatus
OBJECT-TYPE
This object reports the current activity of the modem control feature disabled - The feature is not enabled setup - The feature is configuring the modem error - The feature could not setup the modem idle - The feature is ready to operate dialing - The feature is placing a call dialWait - The feature is between call attempts ringing - The feature is waiting for an incoming call to connect or go away answering - The feature is answering a call negotiating - The feature is negotiating the login security online - The feature data path is connected disconnecting - The feature is disconnecting a call awaitingCallback - The feature is waiting for a security callback
1.3.6.1.4.1.321.100.1.8.1.1.13INTEGER {other(1), disabled(2), idle(3), dialing(4), answering(5), negotiating(6), online(7), disconnecting(8), error(9), setup(10), awaitingCallback(11), dialWait(12), ringing(13)}read-onlycurrent
ipadModemDialSecurity
OBJECT-TYPE
disable - Dial-up security not enabled password - Challenge/Login password scripts used callback - Password security followed by answerer calling back callbackVerify - Callback and verify using the callback challenge/response scripts
1.3.6.1.4.1.321.100.1.8.1.1.14INTEGER {other(1), disable(2), password(3), callback(4), callbackVerify(5)}read-writecurrent
ipadModemDialCallbackRedialDelay
OBJECT-TYPE
Specifies the number of seconds to wait before redialing. Range is 1..255.
1.3.6.1.4.1.321.100.1.8.1.1.15INTEGERread-writecurrent
ipadModemDialCallbackTimeout
OBJECT-TYPE
This object sets the number of seconds to wait for a security callback before failing the connection attempt.
1.3.6.1.4.1.321.100.1.8.1.1.16INTEGERread-writecurrent
ipadModemDialCallbackChalScript
OBJECT-TYPE
Callback security challenge script interpreted after originating a callback dial-up connection.
1.3.6.1.4.1.321.100.1.8.1.1.17DisplayString (SIZE(0..60))read-writecurrent
ipadModemDialCallbackRspScript
OBJECT-TYPE
Callback security challenge response script interpreted after answering a callback dial-up connection.
1.3.6.1.4.1.321.100.1.8.1.1.18DisplayString (SIZE(0..60))read-writecurrent
ipadModemDataTable
OBJECT-TYPE
Table of modem database parameters.
1.3.6.1.4.1.321.100.1.8.2not-accessiblecurrent
ipadModemDataTableEntry
OBJECT-TYPE
An entry in the ipad modem database parameters table.
1.3.6.1.4.1.321.100.1.8.2.1not-accessiblecurrent
ipadModemDataTableIndex
OBJECT-TYPE
The index into the ipad modem database parameters table.
1.3.6.1.4.1.321.100.1.8.2.1.1INTEGERread-onlycurrent
ipadModemDataModemName
OBJECT-TYPE
Identification string for the modem database.
1.3.6.1.4.1.321.100.1.8.2.1.2DisplayString (SIZE(0..10))read-writecurrent
ipadModemDataSetupScript
OBJECT-TYPE
First script interpreted when a modem port is initialized.
1.3.6.1.4.1.321.100.1.8.2.1.3DisplayString (SIZE(0..60))read-writecurrent
ipadModemDataDialingScript
OBJECT-TYPE
Script interpreted when a dial-up connection is initiated.
1.3.6.1.4.1.321.100.1.8.2.1.4DisplayString (SIZE(0..60))read-writecurrent
ipadModemDataAnswerScript
OBJECT-TYPE
Script interpreted when a modem port decides to answer an incoming call.
1.3.6.1.4.1.321.100.1.8.2.1.5DisplayString (SIZE(0..60))read-writecurrent
ipadModemDataHangupScript
OBJECT-TYPE
Script interpreted when a dial-up connection is no longer needed.
1.3.6.1.4.1.321.100.1.8.2.1.6DisplayString (SIZE(0..60))read-writecurrent
ipadModemDataSyncScript
OBJECT-TYPE
Script interpreted to configure the modem to pass synchronous data.
1.3.6.1.4.1.321.100.1.8.2.1.7DisplayString (SIZE(0..60))read-writecurrent
ipadModemDataSyncMethod
OBJECT-TYPE
This object specifies how synchronous user data is passed to the modem. none - The modem does not support synchronous user data. sync - The modem directly supports synchronous user data. v80 - Synchronous user data is exchanged using ITU-T V.80 procedures without CRC. v80crc - Synchronous user data is exchanged using ITU-T V.80 procedures with CRC. rfc1662 - Synchronous user data is exchanged using the method described by RFC1662.
1.3.6.1.4.1.321.100.1.8.2.1.8INTEGER {other(1), none(2), sync(3), v80(4), rfc1662(5), v80crc(6)}read-writecurrent
ipadModemDataSetupScript2
OBJECT-TYPE
Second script interpreted when a modem port is initialized.
1.3.6.1.4.1.321.100.1.8.2.1.9DisplayString (SIZE(0..60))read-writecurrent
ipadModemDataSetupScript3
OBJECT-TYPE
Third script interpreted when a modem port is initialized.
1.3.6.1.4.1.321.100.1.8.2.1.10DisplayString (SIZE(0..60))read-writecurrent
ipadModemDataSetupScript4
OBJECT-TYPE
Fourth script interpreted when a modem port is initialized.
1.3.6.1.4.1.321.100.1.8.2.1.11DisplayString (SIZE(0..60))read-writecurrent
ipadModemDataSetupScript5
OBJECT-TYPE
Fifth script interpreted when a modem port is initialized.
1.3.6.1.4.1.321.100.1.8.2.1.12DisplayString (SIZE(0..60))read-writecurrent
ipadDbuTable
OBJECT-TYPE
The Dial Backup configuration table.
1.3.6.1.4.1.321.100.1.8.3not-accessiblecurrent
ipadDbuTableEntry
OBJECT-TYPE
An entry in the Dial Backup configuration table.
1.3.6.1.4.1.321.100.1.8.3.1not-accessiblecurrent
ipadDbuIndex
OBJECT-TYPE
An index into the Dial Backup configuration table. Equivalent to MIB-II ifIndex.
1.3.6.1.4.1.321.100.1.8.3.1.1INTEGERread-onlycurrent
ipadDbuOperation
OBJECT-TYPE
This object specifes the basic operation of the Dial Backup feature. disable - Dial Backup is not to operate automatic - Dial Backup will start and end automatically automaticDaily - Dial Backup will operate automatically within the specified times in the Daily Dial Backup Table forceBackup - The unit will operate in backup mode unconditionally testOriginate - The unit will start backup procedures and hold the dial-up connection testAnswer - The unit will await a call, establish, and hold the dial-up connection
1.3.6.1.4.1.321.100.1.8.3.1.2INTEGER {other(1), disable(2), automatic(3), automaticDaily(4), forceBackup(5), testOriginate(6), testAnswer(7)}read-writecurrent
ipadDbuMonitoredifIndex
OBJECT-TYPE
Network MIB-II ifIndex monitored by Dial Backup.
1.3.6.1.4.1.321.100.1.8.3.1.7INTEGERread-writecurrent
ipadDbuActivator1
OBJECT-TYPE
This object specifies what will trigger a dial backup activation. disable - No alarm will trigger any - Trigger on any active alarm listed here carrier - Trigger on LOS, OOF, or OOS alarms es - Trigger on the Errored Seconds alarm ses - Trigger on the Severely Errored Seconds alarm uas - Trigger on the Unavailable Seconds alarm los - Trigger on the Loss Of Signal alarm cs - Trigger on the Controlled Slip alarm bpv - Trigger on the Bipolar Violation alarm oof - Trigger on the Out Of Frame alarm ais - Trigger on the Alarm Indication Signal alarm ras - Trigger on the Remote Alarm Signal alarm oos - Trigger on the Out Of Service alarm
1.3.6.1.4.1.321.100.1.8.3.1.8INTEGER {other(1), disable(2), any(3), carrier(4), es(5), ses(6), uas(7), los(8), cs(9), bpv(10), oof(11), ais(12), ras(13), oos(14)}read-writecurrent
ipadDbuActivator2
OBJECT-TYPE
This object specifies what will trigger a dial backup activation. disable - No alarm will trigger any - Trigger on any active alarm listed here carrier - Trigger on LOS, OOF, or OOS alarms es - Trigger on the Errored Seconds alarm ses - Trigger on the Severely Errored Seconds alarm uas - Trigger on the Unavailable Seconds alarm los - Trigger on the Loss Of Signal alarm cs - Trigger on the Controlled Slip alarm bpv - Trigger on the Bipolar Violation alarm oof - Trigger on the Out Of Frame alarm ais - Trigger on the Alarm Indication Signal alarm ras - Trigger on the Remote Alarm Signal alarm oos - Trigger on the Out Of Service alarm
1.3.6.1.4.1.321.100.1.8.3.1.9INTEGER {other(1), disable(2), any(3), carrier(4), es(5), ses(6), uas(7), los(8), cs(9), bpv(10), oof(11), ais(12), ras(13), oos(14)}read-writecurrent
ipadDbuRevertDelay
OBJECT-TYPE
This object specifies the number of seconds the dial backup activators must be continuously gone before the normal connection is restored.
1.3.6.1.4.1.321.100.1.8.3.1.10INTEGERread-writecurrent
ipadDbuTrapDelay
OBJECT-TYPE
This object specifies the number of seconds after entering the active state before sending the Dial Backup trap.
1.3.6.1.4.1.321.100.1.8.3.1.11INTEGERread-writecurrent
ipadDbuStatus
OBJECT-TYPE
This object reports the current activity of the Dial Backup feature disabled - The feature is not enabled setup - The feature is configuring the modem error - The feature could not setup the modem standby - The feature is ready to operate disallowed - The Dial Backup Daily table prevents activation dialing - The feature is placing a call dialWait - The feature is between call attempts ringing - The feature is waiting for an incoming call to connect or go away answering - The feature is answering a call negotiating - The feature is negotiating the login security awaitingCallback - The feature is waiting for a security callback active - The feature backup path is connected disconnecting - The feature is disconnecting a call testWaiting - The feature is waiting for a link test call testPassed - The feature has successfully tested the backup link testFailed - The feature could not establish the backup link
1.3.6.1.4.1.321.100.1.8.3.1.12INTEGER {other(1), disabled(2), standby(3), disallowed(4), dialing(5), answering(6), negotiating(7), awaitingCallback(8), active(9), disconnecting(10), testWaiting(11), testPassed(12), testFailed(13), error(14), setup(15), dialWait(16), ringing(17)}read-onlycurrent
ipadDbuTrap
OBJECT-TYPE
Enable or disable the Dial Backup trap.
1.3.6.1.4.1.321.100.1.8.3.1.13INTEGER {other(1), disable(2), enable(3)}read-writecurrent
ipadDbuDailyTable
OBJECT-TYPE
The Daily Dial Backup Times Table.
1.3.6.1.4.1.321.100.1.8.4not-accessiblecurrent
ipadDbuDailyTableEntry
OBJECT-TYPE
An entry in the Daily Dial Backup Times Table.
1.3.6.1.4.1.321.100.1.8.4.1not-accessiblecurrent
ipadDbuDailyIndex
OBJECT-TYPE
An index into the Daily Dial Backup Times Table. Equivalent to MIB-II ifIndex.
1.3.6.1.4.1.321.100.1.8.4.1.1INTEGERread-onlycurrent
ipadDbuDailyDayOfWeek
OBJECT-TYPE
This is the day of the week index into the Daily Dial Backup Times Table.
1.3.6.1.4.1.321.100.1.8.4.1.2INTEGER {sunday(1), monday(2), tuesday(3), wednesday(4), thursday(5), friday(6), saturday(7)}read-onlycurrent
ipadDbuDailyStart
OBJECT-TYPE
This object is the beginning of a window for Dial Backup activation.
1.3.6.1.4.1.321.100.1.8.4.1.3INTEGER {hour00(1), hour01(2), hour02(3), hour03(4), hour04(5), hour05(6), hour06(7), hour07(8), hour08(9), hour09(10), hour10(11), hour11(12), hour12(13), hour13(14), hour14(15), hour15(16), hour16(17), hour17(18), hour18(19), hour19(20), hour20(21), hour21(22), hour22(23), hour23(24)}read-writecurrent
ipadDbuDailyLength
OBJECT-TYPE
This object is the size of a window for Dial Backup activation.
1.3.6.1.4.1.321.100.1.8.4.1.4INTEGER {disable(1), hour01(2), hour02(3), hour03(4), hour04(5), hour05(6), hour06(7), hour07(8), hour08(9), hour09(10), hour10(11), hour11(12), hour12(13), hour13(14), hour14(15), hour15(16), hour16(17), hour17(18), hour18(19), hour19(20), hour20(21), hour21(22), hour22(23), hour23(24), hour24(25)}read-writecurrent
ipadSvcAware
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.1.9
ipadFrPortStatsTable
OBJECT-TYPE
Port statistics.
1.3.6.1.4.1.321.100.1.9.1not-accessiblecurrent
ipadFrPortStatsEntry
OBJECT-TYPE
An entry in the service aware ports statistics table.
1.3.6.1.4.1.321.100.1.9.1.1not-accessiblecurrent
ipadFrPortStatsService
OBJECT-TYPE
Port index in the ipadFrPortStats table; an entry in the ipad service table.
1.3.6.1.4.1.321.100.1.9.1.1.1INTEGERread-onlycurrent
ipadFrPortStatsPeriod
OBJECT-TYPE
The index into the port stats 24-hour table.
1.3.6.1.4.1.321.100.1.9.1.1.2INTEGER {portStatsSummary(1), portStatsCurrent(2), portStatsperiod1(3), portStatsperiod2(4), portStatsperiod3(5), portStatsperiod4(6), portStatsperiod5(7), portStatsperiod6(8), portStatsperiod7(9), portStatsperiod8(10), portStatsperiod9(11), portStatsperiod10(12), portStatsperiod11(13), portStatsperiod12(14), portStatsperiod13(15), portStatsperiod14(16), portStatsperiod15(17), portStatsperiod16(18), portStatsperiod17(19), portStatsperiod18(20), portStatsperiod19(21), portStatsperiod20(22), portStatsperiod21(23), portStatsperiod22(24), portStatsperiod23(25), portStatsperiod24(26), portStatsperiod25(27), portStatsperiod26(28), portStatsperiod27(29), portStatsperiod28(30), portStatsperiod29(31), portStatsperiod30(32), portStatsperiod31(33), portStatsperiod32(34), portStatsperiod33(35), portStatsperiod34(36), portStatsperiod35(37), portStatsperiod36(38), portStatsperiod37(39), portStatsperiod38(40), portStatsperiod39(41), portStatsperiod40(42), portStatsperiod41(43), portStatsperiod42(44), portStatsperiod43(45), portStatsperiod44(46), portStatsperiod45(47), portStatsperiod46(48), portStatsperiod47(49), portStatsperiod48(50), portStatsperiod49(51), portStatsperiod50(52), portStatsperiod51(53), portStatsperiod52(54), portStatsperiod53(55), portStatsperiod54(56), portStatsperiod55(57), portStatsperiod56(58), portStatsperiod57(59), portStatsperiod58(60), portStatsperiod59(61), portStatsperiod60(62), portStatsperiod61(63), portStatsperiod62(64), portStatsperiod63(65), portStatsperiod64(66), portStatsperiod65(67), portStatsperiod66(68), portStatsperiod67(69), portStatsperiod68(70), portStatsperiod69(71), portStatsperiod70(72), portStatsperiod71(73), portStatsperiod72(74), portStatsperiod73(75), portStatsperiod74(76), portStatsperiod75(77), portStatsperiod76(78), portStatsperiod77(79), portStatsperiod78(80), portStatsperiod79(81), portStatsperiod80(82), portStatsperiod81(83), portStatsperiod82(84), portStatsperiod83(85), portStatsperiod84(86), portStatsperiod85(87), portStatsperiod86(88), portStatsperiod87(89), portStatsperiod88(90), portStatsperiod89(91), portStatsperiod90(92), portStatsperiod91(93), portStatsperiod92(94), portStatsperiod93(95), portStatsperiod94(96), portStatsperiod95(97), portStatsperiod96(98)}read-onlycurrent
ipadFrPortStatsTxFrames
OBJECT-TYPE
Number of transmitted frames for the period.
1.3.6.1.4.1.321.100.1.9.1.1.3INTEGERread-onlycurrent
ipadFrPortStatsRxFrames
OBJECT-TYPE
Number of received frames for the period.
1.3.6.1.4.1.321.100.1.9.1.1.4INTEGERread-onlycurrent
ipadFrPortStatsTxOctets
OBJECT-TYPE
Number of transmitted octets for the period.
1.3.6.1.4.1.321.100.1.9.1.1.5INTEGERread-onlycurrent
ipadFrPortStatsRxOctets
OBJECT-TYPE
Number of received octets for the period.
1.3.6.1.4.1.321.100.1.9.1.1.6INTEGERread-onlycurrent
ipadFrPortStatsTxMgmtFrames
OBJECT-TYPE
Number of transmitted management frames for the period.
1.3.6.1.4.1.321.100.1.9.1.1.7INTEGERread-onlycurrent
ipadFrPortStatsRxMgmtFrames
OBJECT-TYPE
Number of received management frames for the period.
1.3.6.1.4.1.321.100.1.9.1.1.8INTEGERread-onlycurrent
ipadFrPortStatsTxMgmtOctets
OBJECT-TYPE
Number of transmitted management octets for the period.
1.3.6.1.4.1.321.100.1.9.1.1.9INTEGERread-onlycurrent
ipadFrPortStatsRxMgmtOctets
OBJECT-TYPE
Number of received management octets for the period.
1.3.6.1.4.1.321.100.1.9.1.1.10INTEGERread-onlycurrent
ipadFrPortStatsRxFECN
OBJECT-TYPE
Number of received frames with FECN set for the period.
1.3.6.1.4.1.321.100.1.9.1.1.11INTEGERread-onlycurrent
ipadFrPortStatsRxBECN
OBJECT-TYPE
Number of received frames with BECN set for the period.
1.3.6.1.4.1.321.100.1.9.1.1.12INTEGERread-onlycurrent
ipadFrPortStatsRxInvalid
OBJECT-TYPE
Number of invalid received frames for the period.
1.3.6.1.4.1.321.100.1.9.1.1.13INTEGERread-onlycurrent
ipadFrPortStatsTxStatInq
OBJECT-TYPE
Number of transmitted status inquiry frames for the period.
1.3.6.1.4.1.321.100.1.9.1.1.14INTEGERread-onlycurrent
ipadFrPortStatsRxStatInq
OBJECT-TYPE
Number of received status inquiry frames for the period.
1.3.6.1.4.1.321.100.1.9.1.1.15INTEGERread-onlycurrent
ipadFrPortStatsTxStatResp
OBJECT-TYPE
Number of transmitted status response frames for the period.
1.3.6.1.4.1.321.100.1.9.1.1.16INTEGERread-onlycurrent
ipadFrPortStatsRxStatResp
OBJECT-TYPE
Number of received status response frames for the period.
1.3.6.1.4.1.321.100.1.9.1.1.17INTEGERread-onlycurrent
ipadFrPortStatsRxInvLMI
OBJECT-TYPE
Number of received frames with an invalid LMI for the period.
1.3.6.1.4.1.321.100.1.9.1.1.18INTEGERread-onlycurrent
ipadFrPortStatsPeak
OBJECT-TYPE
Peak throughput rate for the period (in bits/second).
1.3.6.1.4.1.321.100.1.9.1.1.19INTEGERread-onlycurrent
ipadFrPortStatsAverage
OBJECT-TYPE
Average throughput rate for the period (in bits/second).
1.3.6.1.4.1.321.100.1.9.1.1.20INTEGERread-onlycurrent
ipadFrPortStatsTimeStamp
OBJECT-TYPE
The value of sysUpTime the last time the statistics were updated.
1.3.6.1.4.1.321.100.1.9.1.1.21TimeTicksread-onlycurrent
ipadFrPortStatsTxAvgPercent
OBJECT-TYPE
Average Tx throughput percent for the period.
1.3.6.1.4.1.321.100.1.9.1.1.22INTEGERread-onlycurrent
ipadFrPortStatsTxMaxPercent
OBJECT-TYPE
Maximum Tx throughput percent for the period.
1.3.6.1.4.1.321.100.1.9.1.1.23INTEGERread-onlycurrent
ipadFrPortStatsTxInstantPercent
OBJECT-TYPE
Instantaneous Tx throughput percent for the period.
1.3.6.1.4.1.321.100.1.9.1.1.24INTEGERread-onlycurrent
ipadFrPortStatsTx20PercentSec
OBJECT-TYPE
Number of seconds Tx throughput was 0-20% of bandwidth.
1.3.6.1.4.1.321.100.1.9.1.1.25INTEGERread-onlycurrent
ipadFrPortStatsTx40PercentSec
OBJECT-TYPE
Number of seconds Tx throughput was 21-40% of bandwidth.
1.3.6.1.4.1.321.100.1.9.1.1.26INTEGERread-onlycurrent
ipadFrPortStatsTx60PercentSec
OBJECT-TYPE
Number of seconds Tx throughput was 41-60% of bandwidth.
1.3.6.1.4.1.321.100.1.9.1.1.27INTEGERread-onlycurrent
ipadFrPortStatsTx80PercentSec
OBJECT-TYPE
Number of seconds Tx throughput was 61-80% of bandwidth.
1.3.6.1.4.1.321.100.1.9.1.1.28INTEGERread-onlycurrent
ipadFrPortStatsTx100PercentSec
OBJECT-TYPE
Number of seconds Tx throughput was 81-100% of bandwidth.
1.3.6.1.4.1.321.100.1.9.1.1.29INTEGERread-onlycurrent
ipadFrPortStatsRxAvgPercent
OBJECT-TYPE
Average Rx throughput percent for the period.
1.3.6.1.4.1.321.100.1.9.1.1.30INTEGERread-onlycurrent
ipadFrPortStatsRxMaxPercent
OBJECT-TYPE
Maximum Rx throughput percent for the period.
1.3.6.1.4.1.321.100.1.9.1.1.31INTEGERread-onlycurrent
ipadFrPortStatsRxInstantPercent
OBJECT-TYPE
Instantaneous Rx throughput percent for the period.
1.3.6.1.4.1.321.100.1.9.1.1.32INTEGERread-onlycurrent
ipadFrPortStatsRx20PercentSec
OBJECT-TYPE
Number of seconds Rx throughput was 0-20% of bandwidth.
1.3.6.1.4.1.321.100.1.9.1.1.33INTEGERread-onlycurrent
ipadFrPortStatsRx40PercentSec
OBJECT-TYPE
Number of seconds Rx throughput was 21-40% of bandwidth.
1.3.6.1.4.1.321.100.1.9.1.1.34INTEGERread-onlycurrent
ipadFrPortStatsRx60PercentSec
OBJECT-TYPE
Number of seconds Rx throughput was 41-60% of bandwidth.
1.3.6.1.4.1.321.100.1.9.1.1.35INTEGERread-onlycurrent
ipadFrPortStatsRx80PercentSec
OBJECT-TYPE
Number of seconds Rx throughput was 61-80% of bandwidth.
1.3.6.1.4.1.321.100.1.9.1.1.36INTEGERread-onlycurrent
ipadFrPortStatsRx100PercentSec
OBJECT-TYPE
Number of seconds Rx throughput was 81-100% of bandwidth.
1.3.6.1.4.1.321.100.1.9.1.1.37INTEGERread-onlycurrent
ipadFrPortStatsValidIntervals
OBJECT-TYPE
Number of valid intervals in the table excluding the Summary and Current entries.
1.3.6.1.4.1.321.100.1.9.1.1.38INTEGER (0..96)read-onlycurrent
ipadDLCIstatsTable
OBJECT-TYPE
Port statistics.
1.3.6.1.4.1.321.100.1.9.2not-accessiblecurrent
ipadDLCIstatsEntry
OBJECT-TYPE
An entry in the service aware DLCI statistics table.
1.3.6.1.4.1.321.100.1.9.2.1not-accessiblecurrent
ipadDLCIstatsService
OBJECT-TYPE
The service index for the service aware stats table; identifies an entry in the ipad DLCI table when combined with ipadDLCIstatsDLCI.
1.3.6.1.4.1.321.100.1.9.2.1.1INTEGERread-onlycurrent
ipadDLCIstatsDLCI
OBJECT-TYPE
The DLCI index for the service aware stats table; identifies an entry in the ipad DLCI table when combined with ipadDLCIstatsService.
1.3.6.1.4.1.321.100.1.9.2.1.2INTEGERread-onlycurrent
ipadDLCIstatsPeriod
OBJECT-TYPE
The index into the DLCI stats 24-hour table.
1.3.6.1.4.1.321.100.1.9.2.1.3INTEGER {dlciStatsSummary(1), dlciStatsCurrent(2), dlciStatsperiod1(3), dlciStatsperiod2(4), dlciStatsperiod3(5), dlciStatsperiod4(6), dlciStatsperiod5(7), dlciStatsperiod6(8), dlciStatsperiod7(9), dlciStatsperiod8(10), dlciStatsperiod9(11), dlciStatsperiod10(12), dlciStatsperiod11(13), dlciStatsperiod12(14), dlciStatsperiod13(15), dlciStatsperiod14(16), dlciStatsperiod15(17), dlciStatsperiod16(18), dlciStatsperiod17(19), dlciStatsperiod18(20), dlciStatsperiod19(21), dlciStatsperiod20(22), dlciStatsperiod21(23), dlciStatsperiod22(24), dlciStatsperiod23(25), dlciStatsperiod24(26), dlciStatsperiod25(27), dlciStatsperiod26(28), dlciStatsperiod27(29), dlciStatsperiod28(30), dlciStatsperiod29(31), dlciStatsperiod30(32), dlciStatsperiod31(33), dlciStatsperiod32(34), dlciStatsperiod33(35), dlciStatsperiod34(36), dlciStatsperiod35(37), dlciStatsperiod36(38), dlciStatsperiod37(39), dlciStatsperiod38(40), dlciStatsperiod39(41), dlciStatsperiod40(42), dlciStatsperiod41(43), dlciStatsperiod42(44), dlciStatsperiod43(45), dlciStatsperiod44(46), dlciStatsperiod45(47), dlciStatsperiod46(48), dlciStatsperiod47(49), dlciStatsperiod48(50), dlciStatsperiod49(51), dlciStatsperiod50(52), dlciStatsperiod51(53), dlciStatsperiod52(54), dlciStatsperiod53(55), dlciStatsperiod54(56), dlciStatsperiod55(57), dlciStatsperiod56(58), dlciStatsperiod57(59), dlciStatsperiod58(60), dlciStatsperiod59(61), dlciStatsperiod60(62), dlciStatsperiod61(63), dlciStatsperiod62(64), dlciStatsperiod63(65), dlciStatsperiod64(66), dlciStatsperiod65(67), dlciStatsperiod66(68), dlciStatsperiod67(69), dlciStatsperiod68(70), dlciStatsperiod69(71), dlciStatsperiod70(72), dlciStatsperiod71(73), dlciStatsperiod72(74), dlciStatsperiod73(75), dlciStatsperiod74(76), dlciStatsperiod75(77), dlciStatsperiod76(78), dlciStatsperiod77(79), dlciStatsperiod78(80), dlciStatsperiod79(81), dlciStatsperiod80(82), dlciStatsperiod81(83), dlciStatsperiod82(84), dlciStatsperiod83(85), dlciStatsperiod84(86), dlciStatsperiod85(87), dlciStatsperiod86(88), dlciStatsperiod87(89), dlciStatsperiod88(90), dlciStatsperiod89(91), dlciStatsperiod90(92), dlciStatsperiod91(93), dlciStatsperiod92(94), dlciStatsperiod93(95), dlciStatsperiod94(96), dlciStatsperiod95(97), dlciStatsperiod96(98)}read-onlycurrent
ipadDLCIstatsTxFrames
OBJECT-TYPE
The number of transmitted frames for the period.
1.3.6.1.4.1.321.100.1.9.2.1.4INTEGERread-onlycurrent
ipadDLCIstatsRxFrames
OBJECT-TYPE
The number of received frames for the period.
1.3.6.1.4.1.321.100.1.9.2.1.5INTEGERread-onlycurrent
ipadDLCIstatsTxOctets
OBJECT-TYPE
The number of transmitted octets for the period.
1.3.6.1.4.1.321.100.1.9.2.1.6INTEGERread-onlycurrent
ipadDLCIstatsRxOctets
OBJECT-TYPE
The number of received octets for the period.
1.3.6.1.4.1.321.100.1.9.2.1.7INTEGERread-onlycurrent
ipadDLCIstatsRxFECN
OBJECT-TYPE
The number of received frames with FECN set for the period.
1.3.6.1.4.1.321.100.1.9.2.1.8INTEGERread-onlycurrent
ipadDLCIstatsRxBECN
OBJECT-TYPE
The number of received frames with BECN set for the period.
1.3.6.1.4.1.321.100.1.9.2.1.9INTEGERread-onlycurrent
ipadDLCIstatsRxDE
OBJECT-TYPE
The number of received frames with DE bit set for the period.
1.3.6.1.4.1.321.100.1.9.2.1.10INTEGERread-onlycurrent
ipadDLCIstatsTxExcessCIR
OBJECT-TYPE
The number of transmitted octets in excess of CIR for the period.
1.3.6.1.4.1.321.100.1.9.2.1.11INTEGERread-onlycurrent
ipadDLCIstatsTxExcessBe
OBJECT-TYPE
The number of transmitted octets in excess of Be for the period.
1.3.6.1.4.1.321.100.1.9.2.1.12INTEGERread-onlycurrent
ipadDLCIstatsTxMgmtFrames
OBJECT-TYPE
The number of transmitted management frames for the period.
1.3.6.1.4.1.321.100.1.9.2.1.13INTEGERread-onlycurrent
ipadDLCIstatsRxMgmtFrames
OBJECT-TYPE
The number of received management frames for the period.
1.3.6.1.4.1.321.100.1.9.2.1.14INTEGERread-onlycurrent
ipadDLCIstatsTxMgmtOctets
OBJECT-TYPE
The number of transmitted management octets for the period.
1.3.6.1.4.1.321.100.1.9.2.1.15INTEGERread-onlycurrent
ipadDLCIstatsRxMgmtOctets
OBJECT-TYPE
The number of received management octets for the period.
1.3.6.1.4.1.321.100.1.9.2.1.16INTEGERread-onlycurrent
ipadDLCIstatsPeak
OBJECT-TYPE
Peak throughput rate for the period (in bits/second).
1.3.6.1.4.1.321.100.1.9.2.1.17INTEGERread-onlycurrent
ipadDLCIstatsAverage
OBJECT-TYPE
Average throughput rate for the period (in bits/second).
1.3.6.1.4.1.321.100.1.9.2.1.18INTEGERread-onlycurrent
ipadDLCIstatsDelayPeak
OBJECT-TYPE
Peak roundtrip delay for the period.
1.3.6.1.4.1.321.100.1.9.2.1.19INTEGERread-onlycurrent
ipadDLCIstatsDelayAverage
OBJECT-TYPE
Average roundtrip delay for the period.
1.3.6.1.4.1.321.100.1.9.2.1.20INTEGERread-onlycurrent
ipadDLCIstatsRoundTripTimeouts
OBJECT-TYPE
Number of timeouts on roundtrip delay for the period.
1.3.6.1.4.1.321.100.1.9.2.1.21INTEGERread-onlycurrent
ipadDLCIstatsUAS
OBJECT-TYPE
Number of seconds the DLCI is unavailable.
1.3.6.1.4.1.321.100.1.9.2.1.22INTEGERread-onlycurrent
ipadDLCIstatsFdrCir
OBJECT-TYPE
1.3.6.1.4.1.321.100.1.9.2.1.23INTEGERread-onlycurrent
ipadDLCIstatsDdrCir
OBJECT-TYPE
1.3.6.1.4.1.321.100.1.9.2.1.24INTEGERread-onlycurrent
ipadDLCIstatsFdrBe
OBJECT-TYPE
1.3.6.1.4.1.321.100.1.9.2.1.25INTEGERread-onlycurrent
ipadDLCIstatsDdrBe
OBJECT-TYPE
1.3.6.1.4.1.321.100.1.9.2.1.26INTEGERread-onlycurrent
ipadDLCIstatsTimeStamp
OBJECT-TYPE
The value of sysUpTime the last time the statistics were updated.
1.3.6.1.4.1.321.100.1.9.2.1.27TimeTicksread-onlycurrent
ipadDLCIstatsRemoteFramesOfferedWithinCIR
OBJECT-TYPE
Count of frames sent within CIR from the remote end of the DLCI.
1.3.6.1.4.1.321.100.1.9.2.1.28INTEGERread-onlycurrent
ipadDLCIstatsRemoteFramesOfferedWithinBE
OBJECT-TYPE
Count of frames sent within BE, but over CIR, from the remote end of the DLCI.
1.3.6.1.4.1.321.100.1.9.2.1.29INTEGERread-onlycurrent
ipadDLCIstatsFramesReceived
OBJECT-TYPE
Count of frames received by the local device on this DLCI.
1.3.6.1.4.1.321.100.1.9.2.1.30INTEGERread-onlycurrent
ipadDLCIstatsFDRCIR
OBJECT-TYPE
Frame Delivery Ratio calculated within CIR.
1.3.6.1.4.1.321.100.1.9.2.1.31DisplayStringread-onlycurrent
ipadDLCIstatsFDRBE
OBJECT-TYPE
Frame Delivery Ratio caclulated within BE.
1.3.6.1.4.1.321.100.1.9.2.1.32DisplayStringread-onlycurrent
ipadDLCIstatsRemoteDataOfferedWithinCIR
OBJECT-TYPE
Count of data octets sent within CIR from the remote end of the DLCI.
1.3.6.1.4.1.321.100.1.9.2.1.33INTEGERread-onlycurrent
ipadDLCIstatsRemoteDataOfferedWithinBE
OBJECT-TYPE
Count of data octets sent within BE, but over CIR, from the remote end of the DLCI.
1.3.6.1.4.1.321.100.1.9.2.1.34INTEGERread-onlycurrent
ipadDLCIstatsDataReceived
OBJECT-TYPE
Count of data octets received by the local device on this DLCI.
1.3.6.1.4.1.321.100.1.9.2.1.35INTEGERread-onlycurrent
ipadDLCIstatsDDRCIR
OBJECT-TYPE
Data Delivery Ratio calculated within CIR.
1.3.6.1.4.1.321.100.1.9.2.1.36DisplayStringread-onlycurrent
ipadDLCIstatsDDRBE
OBJECT-TYPE
Data Delivery Ratio caclulated within BE.
1.3.6.1.4.1.321.100.1.9.2.1.37DisplayStringread-onlycurrent
ipadDLCIstatsAvgPercent
OBJECT-TYPE
Average throughput percent for the period.
1.3.6.1.4.1.321.100.1.9.2.1.38INTEGERread-onlycurrent
ipadDLCIstatsMaxPercent
OBJECT-TYPE
Maximum throughput percent for the period.
1.3.6.1.4.1.321.100.1.9.2.1.39INTEGERread-onlycurrent
ipadDLCIstatsInstantPercent
OBJECT-TYPE
Instantaneous throughput percent for the period.
1.3.6.1.4.1.321.100.1.9.2.1.40INTEGERread-onlycurrent
ipadDLCIstats20PercentSec
OBJECT-TYPE
Number of seconds throughput was 0-20% of bandwidth.
1.3.6.1.4.1.321.100.1.9.2.1.41INTEGERread-onlycurrent
ipadDLCIstats40PercentSec
OBJECT-TYPE
Number of seconds throughput was 21-40% of bandwidth.
1.3.6.1.4.1.321.100.1.9.2.1.42INTEGERread-onlycurrent
ipadDLCIstats60PercentSec
OBJECT-TYPE
Number of seconds throughput was 41-60% of bandwidth.
1.3.6.1.4.1.321.100.1.9.2.1.43INTEGERread-onlycurrent
ipadDLCIstats80PercentSec
OBJECT-TYPE
Number of seconds throughput was 61-80% of bandwidth.
1.3.6.1.4.1.321.100.1.9.2.1.44INTEGERread-onlycurrent
ipadDLCIstats100PercentSec
OBJECT-TYPE
Number of seconds throughput was 81-100% of bandwidth.
1.3.6.1.4.1.321.100.1.9.2.1.45INTEGERread-onlycurrent
ipadDLCIstatsValidIntervals
OBJECT-TYPE
Number of valid intervals in the table excluding the Summary and Current entries.
1.3.6.1.4.1.321.100.1.9.2.1.46INTEGER (0..96)read-onlycurrent
ipadDLCIstatsCompressionTxOctetsIn
OBJECT-TYPE
Number of octets passed into the compression engine.
1.3.6.1.4.1.321.100.1.9.2.1.47INTEGERread-onlycurrent
ipadDLCIstatsCompressionTxOctetsOut
OBJECT-TYPE
Number of octets passed out of the compression engine.
1.3.6.1.4.1.321.100.1.9.2.1.48INTEGERread-onlycurrent
ipadDLCIstatsCompressionRxOctetsIn
OBJECT-TYPE
Number of octets passed into the compression engine.
1.3.6.1.4.1.321.100.1.9.2.1.49INTEGERread-onlycurrent
ipadDLCIstatsCompressionRxOctetsOut
OBJECT-TYPE
Number of octets passed out of the compression engine.
1.3.6.1.4.1.321.100.1.9.2.1.50INTEGERread-onlycurrent
ipadDLCIstatsCompressionTxRatio
OBJECT-TYPE
Compression Ratio calculated in the transmit direction.
1.3.6.1.4.1.321.100.1.9.2.1.51DisplayStringread-onlycurrent
ipadDLCIstatsCompressionRxRatio
OBJECT-TYPE
Compression Ratio calculation in the receive direction.
1.3.6.1.4.1.321.100.1.9.2.1.52DisplayStringread-onlycurrent
ipadUserStatsTable
OBJECT-TYPE
User-selected protocol statistics.
1.3.6.1.4.1.321.100.1.9.3not-accessiblecurrent
ipadUserStatsEntry
OBJECT-TYPE
An entry in the user statistics table.
1.3.6.1.4.1.321.100.1.9.3.1not-accessiblecurrent
ipadUserStatsIndex
OBJECT-TYPE
Index into the user statistics table.
1.3.6.1.4.1.321.100.1.9.3.1.1INTEGERread-onlycurrent
ipadUserStatsPeriod
OBJECT-TYPE
The index into the user stats 24-hour table.
1.3.6.1.4.1.321.100.1.9.3.1.2INTEGER {userStatsSummary(1), userStatsCurrent(2), userStatsperiod1(3), userStatsperiod2(4), userStatsperiod3(5), userStatsperiod4(6), userStatsperiod5(7), userStatsperiod6(8), userStatsperiod7(9), userStatsperiod8(10), userStatsperiod9(11), userStatsperiod10(12), userStatsperiod11(13), userStatsperiod12(14), userStatsperiod13(15), userStatsperiod14(16), userStatsperiod15(17), userStatsperiod16(18), userStatsperiod17(19), userStatsperiod18(20), userStatsperiod19(21), userStatsperiod20(22), userStatsperiod21(23), userStatsperiod22(24), userStatsperiod23(25), userStatsperiod24(26), userStatsperiod25(27), userStatsperiod26(28), userStatsperiod27(29), userStatsperiod28(30), userStatsperiod29(31), userStatsperiod30(32), userStatsperiod31(33), userStatsperiod32(34), userStatsperiod33(35), userStatsperiod34(36), userStatsperiod35(37), userStatsperiod36(38), userStatsperiod37(39), userStatsperiod38(40), userStatsperiod39(41), userStatsperiod40(42), userStatsperiod41(43), userStatsperiod42(44), userStatsperiod43(45), userStatsperiod44(46), userStatsperiod45(47), userStatsperiod46(48), userStatsperiod47(49), userStatsperiod48(50), userStatsperiod49(51), userStatsperiod50(52), userStatsperiod51(53), userStatsperiod52(54), userStatsperiod53(55), userStatsperiod54(56), userStatsperiod55(57), userStatsperiod56(58), userStatsperiod57(59), userStatsperiod58(60), userStatsperiod59(61), userStatsperiod60(62), userStatsperiod61(63), userStatsperiod62(64), userStatsperiod63(65), userStatsperiod64(66), userStatsperiod65(67), userStatsperiod66(68), userStatsperiod67(69), userStatsperiod68(70), userStatsperiod69(71), userStatsperiod70(72), userStatsperiod71(73), userStatsperiod72(74), userStatsperiod73(75), userStatsperiod74(76), userStatsperiod75(77), userStatsperiod76(78), userStatsperiod77(79), userStatsperiod78(80), userStatsperiod79(81), userStatsperiod80(82), userStatsperiod81(83), userStatsperiod82(84), userStatsperiod83(85), userStatsperiod84(86), userStatsperiod85(87), userStatsperiod86(88), userStatsperiod87(89), userStatsperiod88(90), userStatsperiod89(91), userStatsperiod90(92), userStatsperiod91(93), userStatsperiod92(94), userStatsperiod93(95), userStatsperiod94(96), userStatsperiod95(97), userStatsperiod96(98)}read-onlycurrent
ipadUserStatsTxFrames
OBJECT-TYPE
Number of transmitted frames for the period.
1.3.6.1.4.1.321.100.1.9.3.1.3INTEGERread-onlycurrent
ipadUserStatsRxFrames
OBJECT-TYPE
Number of received frames for the period.
1.3.6.1.4.1.321.100.1.9.3.1.4INTEGERread-onlycurrent
ipadUserStatsTxOctets
OBJECT-TYPE
Number of transmitted octets for the period.
1.3.6.1.4.1.321.100.1.9.3.1.5INTEGERread-onlycurrent
ipadUserStatsRxOctets
OBJECT-TYPE
Number of received octets for the period.
1.3.6.1.4.1.321.100.1.9.3.1.6INTEGERread-onlycurrent
ipadUserStatsTxRatePeak
OBJECT-TYPE
Peak throughput rate for the period (in bits/second).
1.3.6.1.4.1.321.100.1.9.3.1.7INTEGERread-onlycurrent
ipadUserStatsTxRateAverage
OBJECT-TYPE
Average throughput rate for the period (in bits/second).
1.3.6.1.4.1.321.100.1.9.3.1.8INTEGERread-onlycurrent
ipadUserStatsTimeStamp
OBJECT-TYPE
The value of sysUpTime the last time the statistics were updated.
1.3.6.1.4.1.321.100.1.9.3.1.9TimeTicksread-onlycurrent
ipadIPTopNStatsTable
OBJECT-TYPE
IP TopN statistics.
1.3.6.1.4.1.321.100.1.9.4not-accessiblecurrent
ipadIPTopNStatsEntry
OBJECT-TYPE
An entry in the user statistics table.
1.3.6.1.4.1.321.100.1.9.4.1not-accessiblecurrent
ipadIPTopNStatsIndex
OBJECT-TYPE
Index into the IP TopN statistics table.
1.3.6.1.4.1.321.100.1.9.4.1.1INTEGERread-onlycurrent
ipadIPTopNStatsAddress
OBJECT-TYPE
IP address of this entry.
1.3.6.1.4.1.321.100.1.9.4.1.2OCTET STRING (SIZE(1..16))read-onlycurrent
ipadIPTopNStatsTimestamp
OBJECT-TYPE
Time of last IP frame for this entry.
1.3.6.1.4.1.321.100.1.9.4.1.3TimeTicksread-onlycurrent
ipadIPTopNStatsRxFrames
OBJECT-TYPE
Number of received IP frames for this entry.
1.3.6.1.4.1.321.100.1.9.4.1.4INTEGERread-onlycurrent
ipadIPTopNStatsRxOctets
OBJECT-TYPE
Number of received IP octets for this entry.
1.3.6.1.4.1.321.100.1.9.4.1.5INTEGERread-onlycurrent
ipadIPTopNStatsTxFrames
OBJECT-TYPE
Number of transmitted IP frames for this entry.
1.3.6.1.4.1.321.100.1.9.4.1.6INTEGERread-onlycurrent
ipadIPTopNStatsTxOctets
OBJECT-TYPE
Number of transmitted IP octets for this entry.
1.3.6.1.4.1.321.100.1.9.4.1.7INTEGERread-onlycurrent
ipadPktSwitch
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.1.10
ipadPktSwOperatingMode
OBJECT-TYPE
Selects overall mode of operation.
1.3.6.1.4.1.321.100.1.10.1INTEGER {other(1), tdm(2), monitor(3), packet(4), remoteConfig(5), profile2(6), profile3(7), profile4(8), profile5(9), profile6(10), profile7(11), profile8(12), profile9(13), profile10(14), profile11(15), profile12(16), profile13(17), profile14(18), profile15(19), profile16(20), profile17(21), profile18(22), profile19(23), profile20(24), profile21(25)}read-writecurrent
ipadPktSwCfgTable
OBJECT-TYPE
The ipad packet switch configuration table.
1.3.6.1.4.1.321.100.1.10.2not-accessiblecurrent
ipadPktSwCfgTableEntry
OBJECT-TYPE
An entry in the ipad packet switch configuration table.
1.3.6.1.4.1.321.100.1.10.2.1not-accessiblecurrent
ipadPktSwCfgService
OBJECT-TYPE
The index into the packet switch configuration table; an entry in the ipad Service table.
1.3.6.1.4.1.321.100.1.10.2.1.1INTEGERread-onlycurrent
ipadPktSwCfgInterfaceType
OBJECT-TYPE
Network ports should be set to User Network Interface (uni) and user ports should be set to Network Interface (ni).
1.3.6.1.4.1.321.100.1.10.2.1.2INTEGER {uni(1), ni(2), nni(3)}read-writecurrent
ipadPktSwCfgLnkMgmtType
OBJECT-TYPE
If set to auto, the frame relay LMI type will be learned from the network side. If set to none, all DLCI must be configured.
1.3.6.1.4.1.321.100.1.10.2.1.3INTEGER {other(1), auto(2), ccitt(3), ansi(4), lmi(5), none(6)}read-writecurrent
ipadPktSwCfgMaxFrameSize
OBJECT-TYPE
This is the maximum frame size configured in the frame relay network.
1.3.6.1.4.1.321.100.1.10.2.1.4INTEGERread-writecurrent
ipadPktSwCfgnN1
OBJECT-TYPE
Number of keep alive requests between full status request.
1.3.6.1.4.1.321.100.1.10.2.1.5INTEGERread-writecurrent
ipadPktSwCfgnN2
OBJECT-TYPE
Number of errors from FRAD before alarm.
1.3.6.1.4.1.321.100.1.10.2.1.6INTEGERread-writecurrent
ipadPktSwCfgnN3
OBJECT-TYPE
Number of events to sample nN2.
1.3.6.1.4.1.321.100.1.10.2.1.7INTEGERread-writecurrent
ipadPktSwCfgnT1
OBJECT-TYPE
Delay before issuing a poll sequence.
1.3.6.1.4.1.321.100.1.10.2.1.8INTEGERread-writecurrent
ipadPktSwCfgDefCIR
OBJECT-TYPE
Default committed information rate in bits per second.
1.3.6.1.4.1.321.100.1.10.2.1.9INTEGERread-writecurrent
ipadPktSwCfgDefExBurst
OBJECT-TYPE
Default excess burst rate in bits per second.
1.3.6.1.4.1.321.100.1.10.2.1.10INTEGERread-writecurrent
ipadPktSwCfgCIREE
OBJECT-TYPE
Determines if the interface will enforce CIR and excess burst configured values.
1.3.6.1.4.1.321.100.1.10.2.1.11INTEGER {other(1), no(2), yes(3)}read-writecurrent
ipadPktSwCfgLinkInjection
OBJECT-TYPE
Indicates how to process frames in excess of the CIR when congestion exists.
1.3.6.1.4.1.321.100.1.10.2.1.12INTEGER {other(1), standard(2), buffered(3), forced(4)}read-writecurrent
ipadPktSwCfgAutoDiagnostic
OBJECT-TYPE
Determines if the unit will put itself into diagnostic mode everytime it determines that there are no LMI received on a network service.
1.3.6.1.4.1.321.100.1.10.2.1.13INTEGER {other(1), no(2), yes(3)}read-writecurrent
ipadPktSwCfgAutoDiscovery
OBJECT-TYPE
Determines if the unit will learn the DLCIs from the LMMI received on this service.
1.3.6.1.4.1.321.100.1.10.2.1.14INTEGER {other(1), no(2), yes(3)}read-writecurrent
ipadPktSwCfgMgmtDLCI
OBJECT-TYPE
Specifies the DLCI that will be used by the unit for management information. Specifying a 0 disables this feature.
1.3.6.1.4.1.321.100.1.10.2.1.15INTEGER (0..4096)read-writecurrent
ipadPktSwCfgRoundTripDelaySize
OBJECT-TYPE
Specifies the packet size in octets used to calculate round trip delay.
1.3.6.1.4.1.321.100.1.10.2.1.16INTEGER (16..1500)read-writecurrent
ipadPktSwCfgRoundTripDelayRate
OBJECT-TYPE
Specifies the packet rate in seconds used to calculate round trip delay.
1.3.6.1.4.1.321.100.1.10.2.1.17INTEGER (1..900)read-writecurrent
ipadPktSwCfgAutoIPMgmtAddr
OBJECT-TYPE
Look for DLCI (980-995) and uses its IP address.
1.3.6.1.4.1.321.100.1.10.2.1.18INTEGER {other(1), no(2), yes(3)}read-writecurrent
ipadPktSwCfgNormalTxQueueSize
OBJECT-TYPE
The depth of the normal priority tx queue. This size determines the max number of low priority packets that can be queued in front of high priority traffic.
1.3.6.1.4.1.321.100.1.10.2.1.19INTEGER (1..32)read-writecurrent
ipadPktSwCfgAddDLCI
OBJECT-TYPE
Identifies a DLCI number to be added.
1.3.6.1.4.1.321.100.1.10.2.1.20INTEGERread-writecurrent
ipadPktSwCfgDeleteDLCI
OBJECT-TYPE
Identifies a DLCI number to be deleted.
1.3.6.1.4.1.321.100.1.10.2.1.21INTEGERread-writecurrent
ipadTrapDest
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.1.11
ipadTrapDestTable
OBJECT-TYPE
The ipad trap destination table.
1.3.6.1.4.1.321.100.1.11.1not-accessiblecurrent
ipadTrapDestTableEntry
OBJECT-TYPE
An entry in the ipad trap destination table.
1.3.6.1.4.1.321.100.1.11.1.1not-accessiblecurrent
ipadTrapDestIndex
OBJECT-TYPE
Index into the ipad trap destination table.
1.3.6.1.4.1.321.100.1.11.1.1.1INTEGERread-onlycurrent
ipadTrapDestination
OBJECT-TYPE
Trap destination.
1.3.6.1.4.1.321.100.1.11.1.1.2IpAddressread-writecurrent
ipadMisc
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.1.12
ipadMiscPortSettings
OBJECT-TYPE
The ipad miscellaneous port settings table.
1.3.6.1.4.1.321.100.1.12.1not-accessiblecurrent
ipadMiscPortSettingsEntry
OBJECT-TYPE
An entry in the ipad miscellaneous port settings table.
1.3.6.1.4.1.321.100.1.12.1.1not-accessiblecurrent
ipadMiscPortSettingsIndex
OBJECT-TYPE
The MIB-II ifIndex for this port.
1.3.6.1.4.1.321.100.1.12.1.1.1INTEGERread-onlycurrent
ipadMiscPortSettingsSerialType
OBJECT-TYPE
The type of this serial port.
1.3.6.1.4.1.321.100.1.12.1.1.2INTEGER {other(1), dce(2), dte(3)}read-writecurrent
ipadMiscPortSettingsModemControl
OBJECT-TYPE
Request the attached service to use the modem dialing control feature.
1.3.6.1.4.1.321.100.1.12.1.1.3INTEGER {other(1), disable(2), enable(3)}read-writecurrent
ipadMiscClearStatusCounts
OBJECT-TYPE
Writing a 2 to this field will clear all status counts.
1.3.6.1.4.1.321.100.1.12.2INTEGER {other(1), clearAll(2)}read-writecurrent
ipadMiscEnableServiceAware
OBJECT-TYPE
Writing a 3 to this field will enable service aware statistics gathering.
1.3.6.1.4.1.321.100.1.12.3INTEGER {other(1), disable(2), enable(3)}read-writecurrent
ipadMiscShdslConfigTable
OBJECT-TYPE
The ipad miscellaneous SHDSL configuration table.
1.3.6.1.4.1.321.100.1.12.4not-accessiblecurrent
ipadMiscShdslConfigEntry
OBJECT-TYPE
An entry in the ipad miscellaneous SHDSL configuration table.
1.3.6.1.4.1.321.100.1.12.4.1not-accessiblecurrent
ipadMiscShdslConfigIndex
OBJECT-TYPE
This object is the index into the SHDSL configuration table.
1.3.6.1.4.1.321.100.1.12.4.1.1INTEGERread-onlycurrent
ipadMiscShdslTerminalType
OBJECT-TYPE
Selects whether the tu is a central or remote site terminal unit. Applicable to HDSL2/SHDSL only.
1.3.6.1.4.1.321.100.1.12.4.1.2INTEGER {other(1), isXtuC(2), isXtuR(3)}read-writecurrent
ipadMiscShdslTiming
OBJECT-TYPE
Sets the timing source to synchronize the unit's internal timing generators.
1.3.6.1.4.1.321.100.1.12.4.1.3INTEGER {shdslTimingOther(1), shdslTimingInternal(2), shdslTimingNetwork(3), shdslTimingEqDTE(4), shdslTimingStation(5), shdslTimingPort1(6), shdslTimingPort2(7)}read-writecurrent
ipadMiscShdslStationInTiming
OBJECT-TYPE
Selects the input timing if SHDSLTiming is set to Station.
1.3.6.1.4.1.321.100.1.12.4.1.4INTEGER {shdslStationInTimingOther(1), shdslStationInTimingNX64(2), shdslStationInTiming1544(3), shdslStationInTiming2048(4)}read-writecurrent
ipadMiscShdslStationTimingNxMultiple
OBJECT-TYPE
Selects the N-multiple when Station Input Timing is set to either NX56 or NX65.
1.3.6.1.4.1.321.100.1.12.4.1.5INTEGERread-writecurrent
ipadMiscShdslAutomaticRetrain
OBJECT-TYPE
Enable or disable automatic line retraining when needed. Enable is the default. Disable is used for PSD measurement.
1.3.6.1.4.1.321.100.1.12.4.1.6INTEGER {other(1), disable(2), enable(3)}read-writecurrent
ipadMiscShdslStatusTable
OBJECT-TYPE
The ipad miscellaneous SHDSL status table.
1.3.6.1.4.1.321.100.1.12.5not-accessiblecurrent
ipadMiscShdslStatusEntry
OBJECT-TYPE
An entry in the ipad miscellaneous SHDSL status table.
1.3.6.1.4.1.321.100.1.12.5.1not-accessiblecurrent
ipadMiscShdslStatusIndex
OBJECT-TYPE
This object is the index into the SHDSL configuration table.
1.3.6.1.4.1.321.100.1.12.5.1.1INTEGERread-onlycurrent
ipadMiscShdslConnectionStatus
OBJECT-TYPE
This object displays the connection status of Wire Pair 1 of an SHDSL connection.
1.3.6.1.4.1.321.100.1.12.5.1.2INTEGER {idle(1), handshake(2), training(3), data(4)}read-onlycurrent
ipadMiscShdslDetailedConnectionStatus
OBJECT-TYPE
This object displays the detailed connection status of Wire Pair 1 of an SHDSL connection.
1.3.6.1.4.1.321.100.1.12.5.1.3DisplayString (SIZE(0..20))read-onlycurrent
ipadMiscShdslEOCInMessages
OBJECT-TYPE
This object displays the number of EOC messages received.
1.3.6.1.4.1.321.100.1.12.5.1.4INTEGERread-onlycurrent
ipadMiscShdslEOCOutMessages
OBJECT-TYPE
This object displays the number of EOC messages transmitted.
1.3.6.1.4.1.321.100.1.12.5.1.5INTEGERread-onlycurrent
ipadMiscShdslConnectionStatusPair2
OBJECT-TYPE
This object displays the connection status of Wire Pair 2 of an SHDSL connection.
1.3.6.1.4.1.321.100.1.12.5.1.6INTEGER {idle(1), handshake(2), training(3), data(4)}read-onlycurrent
ipadMiscShdslDetailedConnectionStatusPair2
OBJECT-TYPE
This object displays the detailed connection status of Wire Pair 2 of an SHDSL connection.
1.3.6.1.4.1.321.100.1.12.5.1.7DisplayString (SIZE(0..20))read-onlycurrent
ipadMiscEnableSupervisoryPort
OBJECT-TYPE
Writing a 2 to this field will disable VT100 and telnet. Writing a 3 to this field will enable VT100 and telnet.
1.3.6.1.4.1.321.100.1.12.6INTEGER {other(1), disable(2), enable(3)}read-writecurrent
ipadMiscEnableButtons
OBJECT-TYPE
Writing a 2 to this field will disable the buttons. Writing a 3 to this field will enable the buttons.
1.3.6.1.4.1.321.100.1.12.7INTEGER {other(1), disable(2), enable(3)}read-writecurrent
ipadMiscBootupConsoleAvail
OBJECT-TYPE
Writing a 2 to this field will disable the console port for diagnostic messages. Writing a 3 to this field will enable these messages.
1.3.6.1.4.1.321.100.1.12.8INTEGER {other(1), disable(2), enable(3)}read-writecurrent
ipadMiscEnableLEDs
OBJECT-TYPE
Writing a 2 to this field will disable the LEDs. Writing a 3 to this field will enable the LEDs.
1.3.6.1.4.1.321.100.1.12.9INTEGER {other(1), disable(2), enable(3)}read-writecurrent
ipadMiscDisableLAN
OBJECT-TYPE
This parameter defines the setup of the Ethernet LAN port. disable(2) - Disable the Ethernet LAN Port. enable(3) - Enable the Ethernet LAN port and auto-negotiate speed and duplex. half10(4) - Enable the Ethernet LAN port and manually set to 10 Mbps and half-duplex. full10(5) - Enable the Ethernet LAN port and manually set to 10 Mbps and full-duplex. half100(6) - Enable the Ethernet LAN port and manually set to 100 Mbps and half-duplex. full100(7) - Enable the Ethernet LAN port and manually set to 100 Mbps and full-duplex.
1.3.6.1.4.1.321.100.1.12.10INTEGER {other(1), disable(2), enable(3), half10(4), full10(5), half100(6), full100(7)}read-writecurrent
ipadMiscLANStatus
OBJECT-TYPE
This parameter defines the setup of the Ethernet LAN port. down(1) - Port has not negotiated. half10(2) - Port negotiated 10 Mbps and half-duplex. full10(3) - Port negotiated 10 Mbps and full-duplex. half100(4) - Port negotiated 100 Mbps and half-duplex. full100(5) - Port negotiated 100 Mbps and full-duplex. na(6) - Not Applicable (speed/duplex manually set).
1.3.6.1.4.1.321.100.1.12.11INTEGER {down(1), half10(2), full10(3), half100(4), full100(5), na(6)}read-onlycurrent
ipadRouter
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.1.13
ipadSoftKey
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.1.14
ipadSoftKeyTable
OBJECT-TYPE
Table of software keys.
1.3.6.1.4.1.321.100.1.14.1not-accessiblecurrent
ipadSoftKeyTableEntry
OBJECT-TYPE
An entry in the software key table.
1.3.6.1.4.1.321.100.1.14.1.1not-accessiblecurrent
ipadSoftKeyIndex
OBJECT-TYPE
Index into the ipad software key table.
1.3.6.1.4.1.321.100.1.14.1.1.1INTEGERread-onlycurrent
ipadSoftKeyAcronym
OBJECT-TYPE
Three-letter acronym for software key.
1.3.6.1.4.1.321.100.1.14.1.1.2DisplayString (SIZE(0..3))read-onlycurrent
ipadSoftKeyDescription
OBJECT-TYPE
Description, if available, of this software key.
1.3.6.1.4.1.321.100.1.14.1.1.3DisplayString (SIZE(0..80))read-onlycurrent
ipadSoftKeyExpirationDate
OBJECT-TYPE
Expiration date of this software key in the format YY/MM/DD.
1.3.6.1.4.1.321.100.1.14.1.1.4DisplayString (SIZE(0..8))read-onlycurrent
ipadSoftKeyEntry
OBJECT-TYPE
Writing a software key will enable that feature (assuming a correct and valid key is entered).
1.3.6.1.4.1.321.100.1.14.2DisplayString (SIZE(0..80))read-writecurrent
ipadTCPServer
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.1.15
ipadTCPServerEnable
OBJECT-TYPE
Enables/disables the TCP Server.
1.3.6.1.4.1.321.100.1.15.1INTEGER {other(1), disable(2), enable(3)}read-writecurrent
ipadTCPServerConnTable
OBJECT-TYPE
Table of TCP Server connections.
1.3.6.1.4.1.321.100.1.15.2not-accessiblecurrent
ipadTCPServerConnTableEntry
OBJECT-TYPE
An entry in the TCP Server connection table.
1.3.6.1.4.1.321.100.1.15.2.1not-accessiblecurrent
ipadTCPServerConnIndex
OBJECT-TYPE
Index into the ipad TCP Server Connection table.
1.3.6.1.4.1.321.100.1.15.2.1.1INTEGERread-onlycurrent
ipadTCPServerConnEndpoint
OBJECT-TYPE
Identifies the endpoint for this connection.
1.3.6.1.4.1.321.100.1.15.2.1.2DisplayString (SIZE(0..11))read-writecurrent
ipadTCPServerConnLocalPort
OBJECT-TYPE
Identifies the TCP port for this connection (default: 2000).
1.3.6.1.4.1.321.100.1.15.2.1.3INTEGER (1..65535)read-writecurrent
ipadTCPServerConnEnableEntry
OBJECT-TYPE
Enables or disables this entry.
1.3.6.1.4.1.321.100.1.15.2.1.4INTEGER {other(1), disable(2), enable(3)}read-writecurrent
ipadTCPServerAddConnEntry
OBJECT-TYPE
Writing addnew(2) to this field causes a new (blank) connection to be appended to the TCP Server Table.
1.3.6.1.4.1.321.100.1.15.3INTEGER {other(1), addnew(2)}read-writecurrent
ipadTCPServerDeleteConnEntry
OBJECT-TYPE
Identifies a connection table entry to be deleted.
1.3.6.1.4.1.321.100.1.15.4INTEGERread-writecurrent
ipadTCPServerHostAccessTable
OBJECT-TYPE
Table of TCP Server IP Host Access List.
1.3.6.1.4.1.321.100.1.15.5not-accessiblecurrent
ipadTCPServerHostAccessTableEntry
OBJECT-TYPE
An entry in the TCP Server Host Access List table.
1.3.6.1.4.1.321.100.1.15.5.1not-accessiblecurrent
ipadTCPServerHostAccessIndex
OBJECT-TYPE
Index into the ipad trap destination table.
1.3.6.1.4.1.321.100.1.15.5.1.1INTEGERread-onlycurrent
ipadTCPServerHostAccessIPAddr
OBJECT-TYPE
Trap destination.
1.3.6.1.4.1.321.100.1.15.5.1.2IpAddressread-writecurrent
ipadSCADAConfig
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.1.16
ipadSCADAConfigTable
OBJECT-TYPE
The SCADA config table.
1.3.6.1.4.1.321.100.1.16.1not-accessiblecurrent
ipadSCADAConfigTableEntry
OBJECT-TYPE
An entry in the SCADA config table.
1.3.6.1.4.1.321.100.1.16.1.1not-accessiblecurrent
ipadSCADACfgIndex
OBJECT-TYPE
The index for SCADA config table.
1.3.6.1.4.1.321.100.1.16.1.1.1INTEGERread-onlycurrent
ipadSCADACfgMessageSize
OBJECT-TYPE
The SCADA message size.
1.3.6.1.4.1.321.100.1.16.1.1.2INTEGERread-writecurrent
ipadSCADACfgIdleCharDelay
OBJECT-TYPE
The SCADA idle character delay.
1.3.6.1.4.1.321.100.1.16.1.1.3INTEGERread-writecurrent
ipadSCADACfgInputTerminator
OBJECT-TYPE
The SCADA input message terminator.
1.3.6.1.4.1.321.100.1.16.1.1.4INTEGERread-writecurrent
ipadSCADACfgAddDevLst
OBJECT-TYPE
Appends an entry to the SCADA device list table.
1.3.6.1.4.1.321.100.1.16.1.1.5INTEGER {other(1), addnew(2)}read-writecurrent
ipadSCADACfgDeleteDevLst
OBJECT-TYPE
Deletes an entry in the SCADA device list table.
1.3.6.1.4.1.321.100.1.16.1.1.6INTEGERread-writecurrent
ipadSCADACfgDataDirection
OBJECT-TYPE
Data Direction enables for SCADA configuration.
1.3.6.1.4.1.321.100.1.16.1.1.7INTEGER {other(1), both(2), output(3), input(4)}read-writecurrent
ipadSCADACfgProtocol
OBJECT-TYPE
Configured SCADA Protocol.
1.3.6.1.4.1.321.100.1.16.1.1.8INTEGER {other(1), async(2), syncVancommHost(3), syncVancommRTU(4)}read-writecurrent
ipadSCADACfgLoopback
OBJECT-TYPE
Loopback allows user to loop data to either Network, Serial Port or both.
1.3.6.1.4.1.321.100.1.16.1.1.9INTEGER {none(1), network(2), port(3), both(4)}read-writecurrent
ipadSCADAStats
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.1.17
ipadSCADAStatsTable
OBJECT-TYPE
The SCADA statistics table.
1.3.6.1.4.1.321.100.1.17.1not-accessiblecurrent
ipadSCADAStatsTableEntry
OBJECT-TYPE
An entry in the SCADA statistics table.
1.3.6.1.4.1.321.100.1.17.1.1not-accessiblecurrent
ipadSCADAStatsIndex
OBJECT-TYPE
The index for SCADA Statistics Table.
1.3.6.1.4.1.321.100.1.17.1.1.1INTEGERread-onlycurrent
ipadSCADAStatsTxChars
OBJECT-TYPE
The number of chracters transmitted through SCADA port.
1.3.6.1.4.1.321.100.1.17.1.1.2INTEGERread-onlycurrent
ipadSCADAStatsRxChars
OBJECT-TYPE
The number of chracters received through SCADA port.
1.3.6.1.4.1.321.100.1.17.1.1.3INTEGERread-onlycurrent
ipadSCADAStatsTxMsgs
OBJECT-TYPE
The number of messages transmitted through SCADA port.
1.3.6.1.4.1.321.100.1.17.1.1.4INTEGERread-onlycurrent
ipadSCADAStatsRxMsgs
OBJECT-TYPE
The number of messages received through SCADA port.
1.3.6.1.4.1.321.100.1.17.1.1.5INTEGERread-onlycurrent
ipadSCADAStatsRxParityErrors
OBJECT-TYPE
The number of parity errors received from SCADA port.
1.3.6.1.4.1.321.100.1.17.1.1.6INTEGERread-onlycurrent
ipadSCADAStatsRxFramingErrors
OBJECT-TYPE
The number of framming errors received from SCADA port.
1.3.6.1.4.1.321.100.1.17.1.1.7INTEGERread-onlycurrent
ipadSCADAStatsClear
OBJECT-TYPE
Writing a value of ipadSCADAStatsClearNow(2) to this field causes all existing stats to be cleared immediately.
1.3.6.1.4.1.321.100.1.17.1.1.8INTEGER {ipadSCADAStatsClearOther(1), ipadSCADAStatsClearNow(2)}read-writecurrent
ipadSCADADevLst
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.1.18
ipadSCADADevLstTable
OBJECT-TYPE
The SCADA device list table.
1.3.6.1.4.1.321.100.1.18.1not-accessiblecurrent
ipadSCADADevLstTableEntry
OBJECT-TYPE
An entry in the SCADA device list table.
1.3.6.1.4.1.321.100.1.18.1.1not-accessiblecurrent
ipadSCADADevLstIndex
OBJECT-TYPE
The index for SCADA device list table.
1.3.6.1.4.1.321.100.1.18.1.1.1INTEGERread-onlycurrent
ipadSCADADevLstDevIndex
OBJECT-TYPE
The index of device.
1.3.6.1.4.1.321.100.1.18.1.1.2INTEGERread-onlycurrent
ipadSCADADevLstEndpointName
OBJECT-TYPE
The name of the endpoint.
1.3.6.1.4.1.321.100.1.18.1.1.3DisplayString (SIZE(0..11))read-writecurrent
ipadSCADADevLstEntryStatus
OBJECT-TYPE
The disabled or dnabled status of the entry.
1.3.6.1.4.1.321.100.1.18.1.1.4INTEGER {other(1), disable(2), enable(3)}read-writecurrent
ipadDS0Config
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.1.19
ipadDS0ConfigTable
OBJECT-TYPE
The ipad DS0 Utilization Monitor Config table.
1.3.6.1.4.1.321.100.1.19.1not-accessiblecurrent
ipadDS0ConfigTableEntry
OBJECT-TYPE
An entry in the ipad DS0 Utilization Monitor Config table.
1.3.6.1.4.1.321.100.1.19.1.1not-accessiblecurrent
ipadDS0ConfigIndex
OBJECT-TYPE
Index into the DS0 Utilization Monitor Config table.
1.3.6.1.4.1.321.100.1.19.1.1.1INTEGERread-onlycurrent
ipadDS0ConfigNumberDS0
OBJECT-TYPE
Number of DS0's monitored by this table entry.
1.3.6.1.4.1.321.100.1.19.1.1.2INTEGERread-onlycurrent
ipadDS0ConfigResetTimer
OBJECT-TYPE
Number of contiguous seconds a utilization alarm must not be present before the alarm condition is automatically reset.
1.3.6.1.4.1.321.100.1.19.1.1.3INTEGERread-writecurrent
ipadDS0ConfigHighUtil
OBJECT-TYPE
What the user considers a high DS0 utilization for this entry. Utilization is expressed as a percentage.
1.3.6.1.4.1.321.100.1.19.1.1.4INTEGERread-writecurrent
ipadDS0ConfigHighUtilThreshold
OBJECT-TYPE
Number of seconds a high utilization condition must be present within 15 minutes before an alarm condition is declared.
1.3.6.1.4.1.321.100.1.19.1.1.5INTEGERread-writecurrent
ipadDS0ConfigHighUtilStatus
OBJECT-TYPE
Indicates if a high utilization condition exists.
1.3.6.1.4.1.321.100.1.19.1.1.6INTEGER {other(1), notExist(2), exists(3)}read-onlycurrent
ipadDS0ConfigHighUtilCount
OBJECT-TYPE
The number of seconds in the past 15 minutes that have been greater than or equal to the high utilization parameter. The value is calculated from a sliding window of 15 one-minute buckets.
1.3.6.1.4.1.321.100.1.19.1.1.7INTEGERread-onlycurrent
ipadDS0ConfigHighUtilAlarm
OBJECT-TYPE
Indicates if the high utilization alarm threshold is exceeded.
1.3.6.1.4.1.321.100.1.19.1.1.8INTEGER {other(1), noAlarm(2), thresholdExceeded(3)}read-onlycurrent
ipadDS0ConfigLowUtil
OBJECT-TYPE
What the user considers an end-of-day low DS0 utilization for this entry. Utilization is expressed as a percentage. When the utilization is set to zero the low utilization alarm is disabled.
1.3.6.1.4.1.321.100.1.19.1.1.9INTEGERread-writecurrent
ipadDS0ConfigLowUtilAlarm
OBJECT-TYPE
Indicates if the low utilization alarm is declared.
1.3.6.1.4.1.321.100.1.19.1.1.10INTEGER {other(1), noAlarm(2), thresholdExceeded(3)}read-onlycurrent
ipadDS0ConfigReset
OBJECT-TYPE
The set values perform the following actions: clearAlarms(2) - Clears any active DS0 utilization alarms and counts clearHistory(3) - Clears DS0 utilization history tables.
1.3.6.1.4.1.321.100.1.19.1.1.11INTEGER {none(1), clearAlarms(2), clearHistory(3)}read-writecurrent
ipadDS0Hist24
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.1.20
ipadDS0Hist24Table
OBJECT-TYPE
The ipad DS0 Utilization Monitor 24-Hour History table.
1.3.6.1.4.1.321.100.1.20.1not-accessiblecurrent
ipadDS0Hist24TableEntry
OBJECT-TYPE
An entry in the ipad DS0 Utilization Monitor 24-Hour History table.
1.3.6.1.4.1.321.100.1.20.1.1not-accessiblecurrent
ipadDS0Hist24Index
OBJECT-TYPE
Index into the DS0 Utilization Monitor 24-Hour History table.
1.3.6.1.4.1.321.100.1.20.1.1.1INTEGERread-onlycurrent
ipadDS0Hist24HistoricalIndex
OBJECT-TYPE
Historical index into the DS0 Utilization Monitor 24-Hour History table.
1.3.6.1.4.1.321.100.1.20.1.1.2INTEGER {statSummary(1), statCurrent(2), statPeriod1(3), statPeriod2(4), statPeriod3(5), statPeriod4(6), statPeriod5(7), statPeriod6(8), statPeriod7(9), statPeriod8(10), statPeriod9(11), statPeriod10(12), statPeriod11(13), statPeriod12(14), statPeriod13(15), statPeriod14(16), statPeriod15(17), statPeriod16(18), statPeriod17(19), statPeriod18(20), statPeriod19(21), statPeriod20(22), statPeriod21(23), statPeriod22(24), statPeriod23(25), statPeriod24(26), statPeriod25(27), statPeriod26(28), statPeriod27(29), statPeriod28(30), statPeriod29(31), statPeriod30(32), statPeriod31(33), statPeriod32(34), statPeriod33(35), statPeriod34(36), statPeriod35(37), statPeriod36(38), statPeriod37(39), statPeriod38(40), statPeriod39(41), statPeriod40(42), statPeriod41(43), statPeriod42(44), statPeriod43(45), statPeriod44(46), statPeriod45(47), statPeriod46(48), statPeriod47(49), statPeriod48(50), statPeriod49(51), statPeriod50(52), statPeriod51(53), statPeriod52(54), statPeriod53(55), statPeriod54(56), statPeriod55(57), statPeriod56(58), statPeriod57(59), statPeriod58(60), statPeriod59(61), statPeriod60(62), statPeriod61(63), statPeriod62(64), statPeriod63(65), statPeriod64(66), statPeriod65(67), statPeriod66(68), statPeriod67(69), statPeriod68(70), statPeriod69(71), statPeriod70(72), statPeriod71(73), statPeriod72(74), statPeriod73(75), statPeriod74(76), statPeriod75(77), statPeriod76(78), statPeriod77(79), statPeriod78(80), statPeriod79(81), statPeriod80(82), statPeriod81(83), statPeriod82(84), statPeriod83(85), statPeriod84(86), statPeriod85(87), statPeriod86(88), statPeriod87(89), statPeriod88(90), statPeriod89(91), statPeriod90(92), statPeriod91(93), statPeriod92(94), statPeriod93(95), statPeriod94(96), statPeriod95(97), statPeriod96(98)}read-onlycurrent
ipadDS0Hist24Timestamp
OBJECT-TYPE
SysUpTime when the utilization interval completed.
1.3.6.1.4.1.321.100.1.20.1.1.3TimeTicksread-onlycurrent
ipadDS0Hist24HighUtilSeconds
OBJECT-TYPE
The number of seconds in the interval that have been greater than or equal to the high utilization parameter.
1.3.6.1.4.1.321.100.1.20.1.1.4INTEGERread-onlycurrent
ipadDS0Hist24Utilization
OBJECT-TYPE
The percent of DS0's utilized over the given interval.
1.3.6.1.4.1.321.100.1.20.1.1.5INTEGERread-onlycurrent
ipadDS0Hist30
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.1.21
ipadDS0Hist30Table
OBJECT-TYPE
The ipad DS0 Utilization Monitor 30-Day History table.
1.3.6.1.4.1.321.100.1.21.1not-accessiblecurrent
ipadDS0Hist30TableEntry
OBJECT-TYPE
An entry in the ipad DS0 Utilization Monitor 30-Day History table.
1.3.6.1.4.1.321.100.1.21.1.1not-accessiblecurrent
ipadDS0Hist30Index
OBJECT-TYPE
Index into the DS0 Utilization Monitor 30-Day History table.
1.3.6.1.4.1.321.100.1.21.1.1.1INTEGERread-onlycurrent
ipadDS0Hist30HistoricalIndex
OBJECT-TYPE
Historical index into the DS0 Utilization Monitor 30-Day History table.
1.3.6.1.4.1.321.100.1.21.1.1.2INTEGER {statSummary(1), statDay1(2), statDay2(3), statDay3(4), statDay4(5), statDay5(6), statDay6(7), statDay7(8), statDay8(9), statDay9(10), statDay10(11), statDay11(12), statDay12(13), statDay13(14), statDay14(15), statDay15(16), statDay16(17), statDay17(18), statDay18(19), statDay19(20), statDay20(21), statDay21(22), statDay22(23), statDay23(24), statDay24(25), statDay25(26), statDay26(27), statDay27(28), statDay28(29), statDay29(30), statDay30(31)}read-onlycurrent
ipadDS0Hist30Timestamp
OBJECT-TYPE
SysUpTime when the utilization interval completed.
1.3.6.1.4.1.321.100.1.21.1.1.3TimeTicksread-onlycurrent
ipadDS0Hist30HighUtilSeconds
OBJECT-TYPE
The number of seconds in the interval that have been greater than or equal to the high utilization parameter.
1.3.6.1.4.1.321.100.1.21.1.1.4INTEGERread-onlycurrent
ipadDS0Hist30Utilization
OBJECT-TYPE
The percent of DS0's utilized over the given interval.
1.3.6.1.4.1.321.100.1.21.1.1.5INTEGERread-onlycurrent
ipadHDLCConfig
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.1.22
ipadHDLCConfigTable
OBJECT-TYPE
The ipad HDLC Utilization Monitor Config table.
1.3.6.1.4.1.321.100.1.22.1not-accessiblecurrent
ipadHDLCConfigTableEntry
OBJECT-TYPE
An entry in the ipad HDLC Utilization Monitor Config table.
1.3.6.1.4.1.321.100.1.22.1.1not-accessiblecurrent
ipadHDLCConfigIndex
OBJECT-TYPE
Index into the HDLC Utilization Monitor Config table.
1.3.6.1.4.1.321.100.1.22.1.1.1INTEGERread-onlycurrent
ipadHDLCConfigService
OBJECT-TYPE
Service the HDLC utilization monitor is attached. 0 = Disabled.
1.3.6.1.4.1.321.100.1.22.1.1.2INTEGERread-writecurrent
ipadHDLCConfigServiceBPS
OBJECT-TYPE
Service bit rate.
1.3.6.1.4.1.321.100.1.22.1.1.3INTEGERread-onlycurrent
ipadHDLCConfigResetTimer
OBJECT-TYPE
Number of contiguous seconds a utilization alarm must not be present before the alarm condition is automatically reset.
1.3.6.1.4.1.321.100.1.22.1.1.4INTEGERread-writecurrent
ipadHDLCConfigRxHighUtil
OBJECT-TYPE
What the user considers a high Rx HDLC utilization for this entry. Utilization is expressed as a percentage.
1.3.6.1.4.1.321.100.1.22.1.1.5INTEGERread-writecurrent
ipadHDLCConfigRxHighUtilThreshold
OBJECT-TYPE
Number of seconds a Rx high utilization condition must be present within 15 minutes before an alarm condition is declared.
1.3.6.1.4.1.321.100.1.22.1.1.6INTEGERread-writecurrent
ipadHDLCConfigRxHighUtilStatus
OBJECT-TYPE
Indicates if a Rx high utilization condition exists.
1.3.6.1.4.1.321.100.1.22.1.1.7INTEGER {other(1), notExist(2), exists(3)}read-onlycurrent
ipadHDLCConfigRxHighUtilCount
OBJECT-TYPE
The number of seconds in the past 15 minutes that have been greater than or equal to the Rx high utilization parameter. The value is calculated from a sliding window of 15 one-minute buckets.
1.3.6.1.4.1.321.100.1.22.1.1.8INTEGERread-onlycurrent
ipadHDLCConfigRxHighUtilAlarm
OBJECT-TYPE
Indicates if the Rx high utilization alarm threshold is exceeded.
1.3.6.1.4.1.321.100.1.22.1.1.9INTEGER {other(1), noAlarm(2), thresholdExceeded(3)}read-onlycurrent
ipadHDLCConfigRxLowUtil
OBJECT-TYPE
What the user considers an end-of-day low Rx HDLC utilization for this entry. Utilization is expressed as a percentage. When the utilization is set to zero the Rx low utilization alarm is disabled.
1.3.6.1.4.1.321.100.1.22.1.1.10INTEGERread-writecurrent
ipadHDLCConfigRxLowUtilAlarm
OBJECT-TYPE
Indicates if the Rx low utilization alarm is declared.
1.3.6.1.4.1.321.100.1.22.1.1.11INTEGER {other(1), noAlarm(2), thresholdExceeded(3)}read-onlycurrent
ipadHDLCConfigTxHighUtil
OBJECT-TYPE
What the user considers a high Tx HDLC utilization for this entry. Utilization is expressed as a percentage.
1.3.6.1.4.1.321.100.1.22.1.1.12INTEGERread-writecurrent
ipadHDLCConfigTxHighUtilThreshold
OBJECT-TYPE
Number of seconds a Tx high utilization condition must be present within 15 minutes before an alarm condition is declared.
1.3.6.1.4.1.321.100.1.22.1.1.13INTEGERread-writecurrent
ipadHDLCConfigTxHighUtilStatus
OBJECT-TYPE
Indicates if a Tx high utilization condition exists.
1.3.6.1.4.1.321.100.1.22.1.1.14INTEGER {other(1), notExist(2), exists(3)}read-onlycurrent
ipadHDLCConfigTxHighUtilCount
OBJECT-TYPE
The number of seconds in the past 15 minutes that have been greater than or equal to the Tx high utilization parameter. The value is calculated from a sliding window of 15 one-minute buckets.
1.3.6.1.4.1.321.100.1.22.1.1.15INTEGERread-onlycurrent
ipadHDLCConfigTxHighUtilAlarm
OBJECT-TYPE
Indicates if the Tx high utilization alarm threshold is exceeded.
1.3.6.1.4.1.321.100.1.22.1.1.16INTEGER {other(1), noAlarm(2), thresholdExceeded(3)}read-onlycurrent
ipadHDLCConfigTxLowUtil
OBJECT-TYPE
What the user considers an end-of-day low Tx HDLC utilization for this entry. Utilization is expressed as a percentage. When the utilization is set to zero the Tx low utilization alarm is disabled.
1.3.6.1.4.1.321.100.1.22.1.1.17INTEGERread-writecurrent
ipadHDLCConfigTxLowUtilAlarm
OBJECT-TYPE
Indicates if the Tx low utilization alarm is declared.
1.3.6.1.4.1.321.100.1.22.1.1.18INTEGER {other(1), noAlarm(2), thresholdExceeded(3)}read-onlycurrent
ipadHDLCConfigReset
OBJECT-TYPE
The set values perform the following actions: clearAlarms(2) - Clears any active HDLC utilization alarms and counts clearHistory(3) - Clears HDLC utilization history tables.
1.3.6.1.4.1.321.100.1.22.1.1.19INTEGER {none(1), clearAlarms(2), clearHistory(3)}read-writecurrent
ipadHDLCHist24
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.1.23
ipadHDLCHist24Table
OBJECT-TYPE
The ipad HDLC Utilization Monitor 24-Hour History table.
1.3.6.1.4.1.321.100.1.23.1not-accessiblecurrent
ipadHDLCHist24TableEntry
OBJECT-TYPE
An entry in the ipad HDLC Utilization Monitor 24-Hour History table.
1.3.6.1.4.1.321.100.1.23.1.1not-accessiblecurrent
ipadHDLCHist24Index
OBJECT-TYPE
Index into the HDLC Utilization Monitor 24-Hour History table.
1.3.6.1.4.1.321.100.1.23.1.1.1INTEGERread-onlycurrent
ipadHDLCHist24HistoricalIndex
OBJECT-TYPE
Historical index into the HDLC Utilization Monitor 24-Hour History table.
1.3.6.1.4.1.321.100.1.23.1.1.2INTEGER {statSummary(1), statCurrent(2), statPeriod1(3), statPeriod2(4), statPeriod3(5), statPeriod4(6), statPeriod5(7), statPeriod6(8), statPeriod7(9), statPeriod8(10), statPeriod9(11), statPeriod10(12), statPeriod11(13), statPeriod12(14), statPeriod13(15), statPeriod14(16), statPeriod15(17), statPeriod16(18), statPeriod17(19), statPeriod18(20), statPeriod19(21), statPeriod20(22), statPeriod21(23), statPeriod22(24), statPeriod23(25), statPeriod24(26), statPeriod25(27), statPeriod26(28), statPeriod27(29), statPeriod28(30), statPeriod29(31), statPeriod30(32), statPeriod31(33), statPeriod32(34), statPeriod33(35), statPeriod34(36), statPeriod35(37), statPeriod36(38), statPeriod37(39), statPeriod38(40), statPeriod39(41), statPeriod40(42), statPeriod41(43), statPeriod42(44), statPeriod43(45), statPeriod44(46), statPeriod45(47), statPeriod46(48), statPeriod47(49), statPeriod48(50), statPeriod49(51), statPeriod50(52), statPeriod51(53), statPeriod52(54), statPeriod53(55), statPeriod54(56), statPeriod55(57), statPeriod56(58), statPeriod57(59), statPeriod58(60), statPeriod59(61), statPeriod60(62), statPeriod61(63), statPeriod62(64), statPeriod63(65), statPeriod64(66), statPeriod65(67), statPeriod66(68), statPeriod67(69), statPeriod68(70), statPeriod69(71), statPeriod70(72), statPeriod71(73), statPeriod72(74), statPeriod73(75), statPeriod74(76), statPeriod75(77), statPeriod76(78), statPeriod77(79), statPeriod78(80), statPeriod79(81), statPeriod80(82), statPeriod81(83), statPeriod82(84), statPeriod83(85), statPeriod84(86), statPeriod85(87), statPeriod86(88), statPeriod87(89), statPeriod88(90), statPeriod89(91), statPeriod90(92), statPeriod91(93), statPeriod92(94), statPeriod93(95), statPeriod94(96), statPeriod95(97), statPeriod96(98)}read-onlycurrent
ipadHDLCHist24Timestamp
OBJECT-TYPE
SysUpTime when the utilization interval completed.
1.3.6.1.4.1.321.100.1.23.1.1.3TimeTicksread-onlycurrent
ipadHDLCHist24RxHighUtilSeconds
OBJECT-TYPE
The number of seconds in the interval that have been greater than or equal to the Rx high utilization parameter.
1.3.6.1.4.1.321.100.1.23.1.1.4INTEGERread-onlycurrent
ipadHDLCHist24RxUtilization
OBJECT-TYPE
The percent of Rx HDLC bandwidth utilized over the given interval.
1.3.6.1.4.1.321.100.1.23.1.1.5INTEGERread-onlycurrent
ipadHDLCHist24TxHighUtilSeconds
OBJECT-TYPE
The number of seconds in the interval that have been greater than or equal to the Tx high utilization parameter.
1.3.6.1.4.1.321.100.1.23.1.1.6INTEGERread-onlycurrent
ipadHDLCHist24TxUtilization
OBJECT-TYPE
The percent of Tx HDLC bandwidth utilized over the given interval.
1.3.6.1.4.1.321.100.1.23.1.1.7INTEGERread-onlycurrent
ipadHDLCHist30
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.1.24
ipadHDLCHist30Table
OBJECT-TYPE
The ipad HDLC Utilization Monitor 30-Day History table.
1.3.6.1.4.1.321.100.1.24.1not-accessiblecurrent
ipadHDLCHist30TableEntry
OBJECT-TYPE
An entry in the ipad HDLC Utilization Monitor 30-Day History table.
1.3.6.1.4.1.321.100.1.24.1.1not-accessiblecurrent
ipadHDLCHist30Index
OBJECT-TYPE
Index into the HDLC Utilization Monitor 30-Day History table.
1.3.6.1.4.1.321.100.1.24.1.1.1INTEGERread-onlycurrent
ipadHDLCHist30HistoricalIndex
OBJECT-TYPE
Historical index into the HDLC Utilization Monitor 30-Day History table.
1.3.6.1.4.1.321.100.1.24.1.1.2INTEGER {statSummary(1), statDay1(2), statDay2(3), statDay3(4), statDay4(5), statDay5(6), statDay6(7), statDay7(8), statDay8(9), statDay9(10), statDay10(11), statDay11(12), statDay12(13), statDay13(14), statDay14(15), statDay15(16), statDay16(17), statDay17(18), statDay18(19), statDay19(20), statDay20(21), statDay21(22), statDay22(23), statDay23(24), statDay24(25), statDay25(26), statDay26(27), statDay27(28), statDay28(29), statDay29(30), statDay30(31)}read-onlycurrent
ipadHDLCHist30Timestamp
OBJECT-TYPE
SysUpTime when the utilization interval completed.
1.3.6.1.4.1.321.100.1.24.1.1.3TimeTicksread-onlycurrent
ipadHDLCHist30RxHighUtilSeconds
OBJECT-TYPE
The number of seconds in the interval that have been greater than or equal to the Rx high utilization parameter.
1.3.6.1.4.1.321.100.1.24.1.1.4INTEGERread-onlycurrent
ipadHDLCHist30RxUtilization
OBJECT-TYPE
The percent of Rx HDLC bandwidth utilized over the given interval.
1.3.6.1.4.1.321.100.1.24.1.1.5INTEGERread-onlycurrent
ipadHDLCHist30TxHighUtilSeconds
OBJECT-TYPE
The number of seconds in the interval that have been greater than or equal to the Tx high utilization parameter.
1.3.6.1.4.1.321.100.1.24.1.1.6INTEGERread-onlycurrent
ipadHDLCHist30TxUtilization
OBJECT-TYPE
The percent of Tx HDLC bandwidth utilized over the given interval.
1.3.6.1.4.1.321.100.1.24.1.1.7INTEGERread-onlycurrent
ipadAtm
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.1.25
ipadNat
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.1.26
ipadDhcp
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.1.27
ipadBridge
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.1.28
ipadSmtp
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.1.29
ipadSmtpMailServer
OBJECT-TYPE
IP Address of the .
1.3.6.1.4.1.321.100.1.29.1IpAddressread-writecurrent
ipadSmtpDomainName
OBJECT-TYPE
Domain Name of the SMTP client.
1.3.6.1.4.1.321.100.1.29.2DisplayStringread-writecurrent
ipadSmtpMailFrom
OBJECT-TYPE
Name of the SMTP client, is used in the From section of the email.
1.3.6.1.4.1.321.100.1.29.3DisplayStringread-writecurrent
ipadSmtpRecipient1
OBJECT-TYPE
Destination for the email.
1.3.6.1.4.1.321.100.1.29.4DisplayStringread-writecurrent
ipadSmtpRecipient2
OBJECT-TYPE
Destination for the email.
1.3.6.1.4.1.321.100.1.29.5DisplayStringread-writecurrent
ipadSmtpRecipient3
OBJECT-TYPE
Destination for the email.
1.3.6.1.4.1.321.100.1.29.6DisplayStringread-writecurrent
ipadSmtpRecipient4
OBJECT-TYPE
Destination for the email.
1.3.6.1.4.1.321.100.1.29.7DisplayStringread-writecurrent
ipadSmtpRecipient5
OBJECT-TYPE
Destination for the email.
1.3.6.1.4.1.321.100.1.29.8DisplayStringread-writecurrent
ipadEncryption
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.1.30
ipadEncryptionEnable
OBJECT-TYPE
Allow disabling encryption.
1.3.6.1.4.1.321.100.1.30.1INTEGER {other(1), disable(2), enable(3)}read-writecurrent
ipadEncryptionStartupKey
OBJECT-TYPE
1.3.6.1.4.1.321.100.1.30.2DisplayString (SIZE(0..56))read-writecurrent
ipadEncryptionStartupKeyConfirm
OBJECT-TYPE
1.3.6.1.4.1.321.100.1.30.3DisplayString (SIZE(0..56))read-writecurrent
ipadEncryptionType
OBJECT-TYPE
1.3.6.1.4.1.321.100.1.30.4INTEGER {blowfish(1), des(2), triple-des(3)}read-writecurrent
ipadEncryptionKey1
OBJECT-TYPE
1.3.6.1.4.1.321.100.1.30.5DisplayString (SIZE(0..56))read-writecurrent
ipadEncryptionKey2
OBJECT-TYPE
1.3.6.1.4.1.321.100.1.30.6DisplayString (SIZE(0..56))read-writecurrent
ipadEncryptionKey3
OBJECT-TYPE
1.3.6.1.4.1.321.100.1.30.7DisplayString (SIZE(0..56))read-writecurrent
ipadEncryptionKey4
OBJECT-TYPE
1.3.6.1.4.1.321.100.1.30.8DisplayString (SIZE(0..56))read-writecurrent
ipadEncryptionKey5
OBJECT-TYPE
1.3.6.1.4.1.321.100.1.30.9DisplayString (SIZE(0..56))read-writecurrent
ipadEncryptionKey6
OBJECT-TYPE
1.3.6.1.4.1.321.100.1.30.10DisplayString (SIZE(0..56))read-writecurrent
ipadEncryptionKey7
OBJECT-TYPE
1.3.6.1.4.1.321.100.1.30.11DisplayString (SIZE(0..56))read-writecurrent
ipadEncryptionKey8
OBJECT-TYPE
1.3.6.1.4.1.321.100.1.30.12DisplayString (SIZE(0..56))read-writecurrent
ipadEncryptionKey9
OBJECT-TYPE
1.3.6.1.4.1.321.100.1.30.13DisplayString (SIZE(0..56))read-writecurrent
ipadEncryptionKey10
OBJECT-TYPE
1.3.6.1.4.1.321.100.1.30.14DisplayString (SIZE(0..56))read-writecurrent
ipadEncryptionKeyLife
OBJECT-TYPE
1.3.6.1.4.1.321.100.1.30.15INTEGERread-writecurrent
ipadAutoLearnDS0
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.1.31
ipadAutoLearnDS0Table
OBJECT-TYPE
The ipad Auto Learn DS0 Config table.
1.3.6.1.4.1.321.100.1.31.1not-accessiblecurrent
ipadAutoLearnDS0TableEntry
OBJECT-TYPE
An entry in the ipad Auto Learn DS0 Config table.
1.3.6.1.4.1.321.100.1.31.1.1not-accessiblecurrent
ipadAutoLearnDS0Index
OBJECT-TYPE
The MIB-II ifIndex into the Auto Learn DS0 Config table.
1.3.6.1.4.1.321.100.1.31.1.1.1INTEGERread-onlycurrent
ipadAutoLearnDS0Boot
OBJECT-TYPE
Select when to automatically learn DS0 assignments: disable - Do not automatically learn DS0s enable - Learn on boot carrierDown - Learn on boot and while the ifIndex carrier is down serviceDown - Learn on boot and while the first service on ifIndex is down
1.3.6.1.4.1.321.100.1.31.1.1.2INTEGER {other(1), disable(2), enable(3), carrierDown(4), serviceDown(5)}read-writecurrent
ipadAutoLearnDS0Rate
OBJECT-TYPE
Select the rate of the learned DS0's.
1.3.6.1.4.1.321.100.1.31.1.1.3INTEGER {other(1), auto(2), learnAs56K(3), learnAs64K(4), learnAsVoice(5)}read-writecurrent
ipadAutoLearnDS0Command
OBJECT-TYPE
The set values perform the following actions: learnNow(2) - Attempt to learn the active DS0's now.
1.3.6.1.4.1.321.100.1.31.1.1.4INTEGER {none(1), learnNow(2)}read-writecurrent
ipadUnitAccess
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.1.32
ipadUnitAccessTable
OBJECT-TYPE
The ipad Unit Access table.
1.3.6.1.4.1.321.100.1.32.1not-accessiblecurrent
ipadUnitAccessTableEntry
OBJECT-TYPE
An entry in the ipad Unit Access table.
1.3.6.1.4.1.321.100.1.32.1.1not-accessiblecurrent
ipadUnitAccessIndex
OBJECT-TYPE
The MIB-II Index into the Unit Access table.
1.3.6.1.4.1.321.100.1.32.1.1.1INTEGERread-onlycurrent
ipadUnitAccessIpa
OBJECT-TYPE
IP Address of Source to allow Unit Access.
1.3.6.1.4.1.321.100.1.32.1.1.2IpAddressread-writecurrent
ipadUnitAccessMask
OBJECT-TYPE
Mask of Source to allow Unit Access.
1.3.6.1.4.1.321.100.1.32.1.1.3IpAddressread-writecurrent
ipadTFTPDownload
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.1.33
ipadTFTPDownloadServerIpa
OBJECT-TYPE
TFTP Server IP Address.
1.3.6.1.4.1.321.100.1.33.1IpAddressread-writecurrent
ipadTFTPDownloadFileName
OBJECT-TYPE
TFTP Filename to Download or Upload.
1.3.6.1.4.1.321.100.1.33.2DisplayString (SIZE(0..80))read-writecurrent
ipadTFTPDownloadAction
OBJECT-TYPE
TFTP Action to be performed.
1.3.6.1.4.1.321.100.1.33.3INTEGER {getfile(1), putfile(2), abort(3), idle(4)}read-writecurrent
ipadTFTPDownloadStatus
OBJECT-TYPE
TFTP current status of action.
1.3.6.1.4.1.321.100.1.33.4INTEGER {idle(1), gettingfile(2), puttingfile(3), aborting(4), successful(5), invalidFileName(6), fileAccessFailed(7), invalidFile(8)}read-onlycurrent
ipadDataLineMonitor
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.1.34
ipadDLMConfig
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.1.34.1
ipadDLMConfigMode
OBJECT-TYPE
Data Link Monitor on/off switch. Toggles mode from analyze (static) to live (capture).
1.3.6.1.4.1.321.100.1.34.1.1INTEGER {other(1), analyze(2), live(3)}read-writecurrent
ipadDLMConfigBufferManagement
OBJECT-TYPE
The DLM has a buffer of n messages. Settings this object to wrap(2) allows the buffer to wrap around and be a continous buffer. stopOnFull(3) forces the capture of packets to stop once the end of the buffer is reached.
1.3.6.1.4.1.321.100.1.34.1.2INTEGER {other(1), wrap(2), stopOnFull(3)}read-writecurrent
ipadDLMTable
OBJECT-TYPE
The ipad Data Line Monitor configuration table.
1.3.6.1.4.1.321.100.1.34.2not-accessiblecurrent
ipadDLMTableEntry
OBJECT-TYPE
An entry in the ipad DLM config table.
1.3.6.1.4.1.321.100.1.34.2.1not-accessiblecurrent
ipadDLMServiceIndex
OBJECT-TYPE
The service index into the DLM table.
1.3.6.1.4.1.321.100.1.34.2.1.1INTEGERread-onlycurrent
ipadDLMEnable
OBJECT-TYPE
Enable/Disable the DLM on the specified service.
1.3.6.1.4.1.321.100.1.34.2.1.2INTEGER {other(1), disable(2), enable(3)}read-writecurrent
ipadDLMTxRxFilter
OBJECT-TYPE
Allows the user to capture only received, transmit, or both.
1.3.6.1.4.1.321.100.1.34.2.1.3INTEGER {other(1), all(2), transmitOnly(3), receiveOnly(4)}read-writecurrent
ipadDLMPatternEnable
OBJECT-TYPE
Enable/Disable the search for a specific pattern.
1.3.6.1.4.1.321.100.1.34.2.1.4INTEGER {other(1), disable(2), enable(3)}read-writecurrent
ipadDLMPattern
OBJECT-TYPE
The pattern to search for in the captured packets.
1.3.6.1.4.1.321.100.1.34.2.1.5INTEGERread-writecurrent
ipadDLMPatternMask
OBJECT-TYPE
The mask to use with ipadDLMPattern to search for in the captured packets.
1.3.6.1.4.1.321.100.1.34.2.1.6INTEGERread-writecurrent
ipadDLMPatternOffset
OBJECT-TYPE
The offset into the packet to search for the pattern.
1.3.6.1.4.1.321.100.1.34.2.1.7INTEGER (0..32)read-writecurrent
ipadDLMPacketTable
OBJECT-TYPE
The ipad Data Link Monitor packet table.
1.3.6.1.4.1.321.100.1.34.3not-accessiblecurrent
ipadDLMPacketTableEntry
OBJECT-TYPE
An entry in the ipad DLM packet table.
1.3.6.1.4.1.321.100.1.34.3.1not-accessiblecurrent
ipadDLMPacketIndex
OBJECT-TYPE
The service index into the DLM table.
1.3.6.1.4.1.321.100.1.34.3.1.1INTEGERread-onlycurrent
ipadDLMPacketServiceIndex
OBJECT-TYPE
The service index the packet was captured on.
1.3.6.1.4.1.321.100.1.34.3.1.2INTEGERread-onlycurrent
ipadDLMPacketTimestamp
OBJECT-TYPE
The time that the packet was captured.
1.3.6.1.4.1.321.100.1.34.3.1.3TimeTicksread-onlycurrent
ipadDLMPacketDataDirection
OBJECT-TYPE
The direction the data was goin in respect to the interface.
1.3.6.1.4.1.321.100.1.34.3.1.4INTEGER {other(1), transmit(2), receive(3)}read-onlycurrent
ipadDLMPacketSize
OBJECT-TYPE
The size of the captured packet.
1.3.6.1.4.1.321.100.1.34.3.1.5INTEGERread-onlycurrent
ipadDLMPacketData
OBJECT-TYPE
The contents of the first 32 bytes of the captured packet.
1.3.6.1.4.1.321.100.1.34.3.1.6OCTET STRING (SIZE(0..32))read-onlycurrent
ipadOrigPing
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.1.35
ipadOrigPingCommand
OBJECT-TYPE
Action command to start/stop sending PING messages.
1.3.6.1.4.1.321.100.1.35.1INTEGER {other(1), stop(2), start(3), clearStats(4)}read-writecurrent
ipadOrigPingDestIPAddr
OBJECT-TYPE
Destination IP address of sent PING request messages.
1.3.6.1.4.1.321.100.1.35.2IpAddressread-writecurrent
ipadOrigPingTimeout
OBJECT-TYPE
Number of seconds to wait for a reply to a PING request message.
1.3.6.1.4.1.321.100.1.35.3INTEGERread-writecurrent
ipadOrigPingSize
OBJECT-TYPE
Number of bytes in a PING request message data field.
1.3.6.1.4.1.321.100.1.35.4INTEGERread-writecurrent
ipadOrigPingToSend
OBJECT-TYPE
Number of PING request messages to send.
1.3.6.1.4.1.321.100.1.35.5INTEGERread-writecurrent
ipadOrigPingSent
OBJECT-TYPE
Number of PING request messages sent.
1.3.6.1.4.1.321.100.1.35.6INTEGERread-onlycurrent
ipadOrigPingReplies
OBJECT-TYPE
Number of PING response messages received.
1.3.6.1.4.1.321.100.1.35.7INTEGERread-onlycurrent
ipadOrigPingDelayMin
OBJECT-TYPE
Minimum PING round trip delay in milliseconds.
1.3.6.1.4.1.321.100.1.35.8INTEGERread-onlycurrent
ipadOrigPingDelayAvg
OBJECT-TYPE
Average PING round trip delay in milliseconds.
1.3.6.1.4.1.321.100.1.35.9INTEGERread-onlycurrent
ipadOrigPingDelayMax
OBJECT-TYPE
Maximum PING round trip delay in milliseconds.
1.3.6.1.4.1.321.100.1.35.10INTEGERread-onlycurrent
ipadOrigPingReport
OBJECT-TYPE
ASCII status report of originate PING activity.
1.3.6.1.4.1.321.100.1.35.11DisplayString (SIZE(0..80))read-onlycurrent
ipadOrigPingExceptReport
OBJECT-TYPE
ASCII status report of last originate PING exception received.
1.3.6.1.4.1.321.100.1.35.12DisplayString (SIZE(0..80))read-onlycurrent
ipadTraps
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.1.999
ipadTrapsPrefix
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.1.999.0

Notifications

NameOIDStatus
ipadFrPortRxInvalidFramesExceeded
NOTIFICATION-TYPE
This trap is sent out when an ipad frame relay port receive invalid frames alarm threshold has been exceeded.
1.3.6.1.4.1.321.100.1.999.0.25000current
ipadFrPortRxThroughputExceeded
NOTIFICATION-TYPE
This trap is sent out when an ipad frame relay port receive throughput threshold has been exceeded.
1.3.6.1.4.1.321.100.1.999.0.25001current
ipadFrPortTxThroughputExceeded
NOTIFICATION-TYPE
This trap is sent out when an ipad frame relay port transmit throughput threshold has been exceeded.
1.3.6.1.4.1.321.100.1.999.0.25002current
ipadDLCItxCIRexceeded
NOTIFICATION-TYPE
This trap is sent out when the Tx over CIR threshold has been exceeded. This threshold is the number of frames in excess of CIR.
1.3.6.1.4.1.321.100.1.999.0.25003current
ipadDLCItxBEexceeded
NOTIFICATION-TYPE
This trap is sent out when the Tx over Be threshold has been exceeded. This threshold is the number of frames in excess of Be.
1.3.6.1.4.1.321.100.1.999.0.25004current
ipadDLCIRxCongestionExceeded
NOTIFICATION-TYPE
This trap is sent out when the Rx congestion threshold has been exceeded. This threshold is the number of frames received with BECN/FECN.
1.3.6.1.4.1.321.100.1.999.0.25005current
ipadUserTxExceeded
NOTIFICATION-TYPE
This trap is sent out when the Tx throughput threshold in bits per second has been exceeded. This threshold represents the number of bits for the user-selected protocol.
1.3.6.1.4.1.321.100.1.999.0.25006current
ipadDlciRxBECNinCIRAlarm
NOTIFICATION-TYPE
This trap is sent out when a frame with BECN set has been received within CIR.
1.3.6.1.4.1.321.100.1.999.0.25007current
ipadDlciUASExceeded
NOTIFICATION-TYPE
This trap is sent out when the UAS (unavailable seconds) threshold for the DLCI has been exceeded.
1.3.6.1.4.1.321.100.1.999.0.25008current
ipadserialDteDTRAlarmExists
NOTIFICATION-TYPE
This trap is sent out when a DTR Loss alarm is declared.
1.3.6.1.4.1.321.100.1.999.0.25009current
ipadt1e1ESAlarmDeclared
NOTIFICATION-TYPE
This trap is sent out when an Errored Seconds alarm is declared.
1.3.6.1.4.1.321.100.1.999.0.25010current
ipadt1e1SESAlarmDeclared
NOTIFICATION-TYPE
This trap is sent out when a Severely Errored Seconds alarm is declared.
1.3.6.1.4.1.321.100.1.999.0.25011current
ipadt1e1LOSSAlarmDeclared
NOTIFICATION-TYPE
This trap is sent out when a Loss of Signal Seconds alarm is declared.
1.3.6.1.4.1.321.100.1.999.0.25012current
ipadt1e1UASAlarmDeclared
NOTIFICATION-TYPE
This trap is sent out when an Unavailable Seconds alarm is declared.
1.3.6.1.4.1.321.100.1.999.0.25013current
ipadt1e1CSSAlarmDeclared
NOTIFICATION-TYPE
This trap is sent out when a Controlled Slip Seconds alarm is declared.
1.3.6.1.4.1.321.100.1.999.0.25014current
ipadt1e1BPVSAlarmDeclared
NOTIFICATION-TYPE
This trap is sent out when a Bipolar Violation Seconds alarm is declared.
1.3.6.1.4.1.321.100.1.999.0.25015current
ipadt1e1OOFSAlarmDeclared
NOTIFICATION-TYPE
This trap is sent out when an Out of Frame Seconds alarm is declared.
1.3.6.1.4.1.321.100.1.999.0.25016current
ipadt1e1AISAlarmExists
NOTIFICATION-TYPE
This trap is sent out when an Alarm Indication Signal alarm is declared.
1.3.6.1.4.1.321.100.1.999.0.25017current
ipadt1e1RASAlarmExists
NOTIFICATION-TYPE
This trap is sent out when a Remote Alarm Signal alarm is declared.
1.3.6.1.4.1.321.100.1.999.0.25018current
ipadDLCIremoteSOSAlarm
NOTIFICATION-TYPE
This trap is sent when the remote unit for a DLCI senses and reports an SOS condition.
1.3.6.1.4.1.321.100.1.999.0.25019current
ipadDdsLOSSAlarmDeclared
NOTIFICATION-TYPE
This trap is sent out when a Loss of Signal Seconds alarm is declared.
1.3.6.1.4.1.321.100.1.999.0.25020current
ipadDdsOOFSAlarmDeclared
NOTIFICATION-TYPE
This trap is sent out when an Out of Frame Seconds alarm is declared.
1.3.6.1.4.1.321.100.1.999.0.25021current
ipadDdsOOSSAlarmDeclared
NOTIFICATION-TYPE
This trap is sent out when an Out of Service Seconds alarm is declared.
1.3.6.1.4.1.321.100.1.999.0.25022current
ipadDdsFDLSAlarmDeclared
NOTIFICATION-TYPE
This trap is sent out when a FDL error Seconds alarm is declared.
1.3.6.1.4.1.321.100.1.999.0.25023current
ipadDdsBPVSAlarmDeclared
NOTIFICATION-TYPE
This trap is sent out when a Bipolar Violation Seconds alarm is declared.
1.3.6.1.4.1.321.100.1.999.0.25024current
ipadDS0HighAlarmDeclared
NOTIFICATION-TYPE
This trap is sent out when a high utilization alarm is declared.
1.3.6.1.4.1.321.100.1.999.0.25025current
ipadDS0LowAlarmDeclared
NOTIFICATION-TYPE
This trap is sent out when a low utilization alarm is declared.
1.3.6.1.4.1.321.100.1.999.0.25026current
ipadHDLCRxHighAlarmDeclared
NOTIFICATION-TYPE
This trap is sent out when a high Rx utilization alarm is declared.
1.3.6.1.4.1.321.100.1.999.0.25027current
ipadHDLCRxLowAlarmDeclared
NOTIFICATION-TYPE
This trap is sent out when a low Rx utilization alarm is declared.
1.3.6.1.4.1.321.100.1.999.0.25028current
ipadHDLCTxHighAlarmDeclared
NOTIFICATION-TYPE
This trap is sent out when a high Tx utilization alarm is declared.
1.3.6.1.4.1.321.100.1.999.0.25029current
ipadHDLCTxLowAlarmDeclared
NOTIFICATION-TYPE
This trap is sent out when a low Tx utilization alarm is declared.
1.3.6.1.4.1.321.100.1.999.0.25030current
ipadDbuActivated
NOTIFICATION-TYPE
This trap is sent out when Dial Backup becomes active.
1.3.6.1.4.1.321.100.1.999.0.25031current