MIBs Depot

DS8200v2-MIB

Registered at
1.3.6.1.4.1.321.100.2
Last updated
1900-08-18 00:00
Organization
Verilink Corporation
Namespace
zhone
Source file
DS8200v2-MIB
Digest
sha256:af9e6727f4ad1335dff3c2ea1bfa78638b92d0f2fca880e39337ac903aaef747

Description

DS8200v2 MIB.

Contact

support@verilink.com + 1 800 285 2755

Imports

FromSymbols
DS8200v2-TC-MIBhbu, verilink
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP
SNMPv2-SMIMODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, enterprises, iso
SNMPv2-TCDisplayString, TEXTUAL-CONVENTION

Imported by

1 module(s) in this corpus import this one.

Load order

Every file a consumer needs in order to load this module, dependencies first.

DS8200v2-MIB
DS8200v2-TC-MIB
SNMPv2-CONF
SNMPv2-SMI
SNMPv2-TC

Objects

NameOIDSyntaxAccessStatus
mgmtPorts
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.2.1
mgmtPortsTable
OBJECT-TYPE
The Management Ports table.
1.3.6.1.4.1.321.100.2.1.1not-accessiblecurrent
mgmtPortsTableEntry
OBJECT-TYPE
An entry in the Management Ports table.
1.3.6.1.4.1.321.100.2.1.1.1not-accessiblecurrent
mgmtPortsTableIndex
OBJECT-TYPE
The index into the Management Ports table.
1.3.6.1.4.1.321.100.2.1.1.1.1INTEGERread-onlycurrent
mgmtPortsDescription
OBJECT-TYPE
Contains a textual description of the port.
1.3.6.1.4.1.321.100.2.1.1.1.2DisplayString (SIZE(0..40))read-onlycurrent
mgmtPortsElementID
OBJECT-TYPE
This object signifies the name of the device.
1.3.6.1.4.1.321.100.2.1.1.1.3DisplayString (SIZE(0..27))read-writecurrent
mgmtPortsMode
OBJECT-TYPE
This object signifies the method used by the port to report alarms.
1.3.6.1.4.1.321.100.2.1.1.1.4INTEGER {other(1), disabled(2), coadial(3), coadirect(4), extAlarmOnOpen(5), extAlarmOnClosed(6), slipdial(7), slipdirect(8)}read-writecurrent
mgmtPortsDialPrefix
OBJECT-TYPE
This object contains the dial string prefix for a modem connected to the port.
1.3.6.1.4.1.321.100.2.1.1.1.5DisplayString (SIZE(0..38))read-writecurrent
mgmtPortsPrimaryDialString
OBJECT-TYPE
This object contains the primary dial string for a modem connected to the port.
1.3.6.1.4.1.321.100.2.1.1.1.6DisplayString (SIZE(0..30))read-writecurrent
mgmtPortsSecondaryDialString
OBJECT-TYPE
This object contains the secondary dial string for a modem connected to the port.
1.3.6.1.4.1.321.100.2.1.1.1.7DisplayString (SIZE(0..30))read-writecurrent
mgmtPortsExtInitString
OBJECT-TYPE
This object contains the init string for a modem connected to the port.
1.3.6.1.4.1.321.100.2.1.1.1.8DisplayString (SIZE(0..38))read-writecurrent
mgmtPortsCompressedSlip
OBJECT-TYPE
This object specifies if SLIP compression is to be used.
1.3.6.1.4.1.321.100.2.1.1.1.9INTEGER {other(1), enabled(2), disabled(3), auto(4)}read-writecurrent
mgmtPortsInternalModem
OBJECT-TYPE
This object signifies if the internal modem (when present) is enabled.
1.3.6.1.4.1.321.100.2.1.1.1.10INTEGER {other(1), notPresent(2), enabled(3), disabled(4)}read-writecurrent
dbu
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.2.2
dbuConfigTable
OBJECT-TYPE
The Dial Backup Configuration Table.
1.3.6.1.4.1.321.100.2.2.1not-accessiblecurrent
dbuConfigTableEntry
OBJECT-TYPE
An entry in the Dial Backup Configuration table.
1.3.6.1.4.1.321.100.2.2.1.1not-accessiblecurrent
dbuNearIndex
OBJECT-TYPE
Selects the near device.
1.3.6.1.4.1.321.100.2.2.1.1.1INTEGERread-onlycurrent
dbuFarIndex
OBJECT-TYPE
Selects the far device.
1.3.6.1.4.1.321.100.2.2.1.1.2INTEGERread-onlycurrent
dbuConfigTableIndex
OBJECT-TYPE
The index into the Dial Backup table.
1.3.6.1.4.1.321.100.2.2.1.1.3INTEGERread-onlycurrent
dbuDescription
OBJECT-TYPE
Contains a textual description of the dbu.
1.3.6.1.4.1.321.100.2.2.1.1.4DisplayString (SIZE(0..40))read-onlycurrent
dbuRate
OBJECT-TYPE
This object is the identifier of the current DDS DBU rate. The values mean: dbuRate2400 the DBU interface is operating at 2400bps dbuRate4800 the DBU interface is operating at 4800bps dbuRate9600 the DBU interface is operating at 9600bps dbuRate19200 the DBU interface is operating at 19200bps dbuRate38400 the DBU interface is operating at 38400bps dbuRate56000 the DBU interface is operating at 56000bps dbuRate57600 the DBU interface is operating at 57600bps dbuRate64000 the DBU interface is operating at 64000bps
1.3.6.1.4.1.321.100.2.2.1.1.5INTEGER {dbuRateOther(1), dbuRate2400(2), dbuRate4800(3), dbuRate9600(4), dbuRate19200(5), dbuRate38400(6), dbuRate56000(7), dbuRate57600(8), dbuRate64000(9)}read-writecurrent
dbuMode
OBJECT-TYPE
This object is the identifier of the current mode that the Dial Backup Unit is operating in. The values mean: dbuModeOrig The dial backup unit is operating in the originate mode dbuModeAnsw The dial backup unit is operating in the answer mode dbuModeNotAvail The dial backup unit's mode is not available dbuModeCallbackOrig The dial backup unit is operating in the callback originate mode dbuModeCallbackAnsw The dial backup unit is operating in the callback mode dbuModeMaster The dial backup unit is configured as a master unit dbuModeSlave The dial backup unit is configured as a slave unit
1.3.6.1.4.1.321.100.2.2.1.1.6INTEGER {dbuModeOther(1), dbuModeOrig(2), dbuModeAnsw(3), dbuModeNotAvail(4), dbuModeCallbackOrig(5), dbuModeCallbackAnsw(6), dbuModeMaster(7), dbuModeSlave(8)}read-writecurrent
dbuFormat
OBJECT-TYPE
This object is the identifier of the current format that the Dial Backup Unit is operating in. The values mean: dbuFormatSync The dial backup unit is operating in the synchronous format dbuFormatAsync The dial backup unit is operating in the asynchronous format dbuFormatNotAvail The dial backup unit's format is not available
1.3.6.1.4.1.321.100.2.2.1.1.7INTEGER {dbuFormatOther(1), dbuFormatSync(2), dbuFormatAsync(3), dbuFormatNotAvail(4)}read-writecurrent
dbuNumber
OBJECT-TYPE
This string is the currently programmed number for the dial backup unit to call
1.3.6.1.4.1.321.100.2.2.1.1.8DisplayString (SIZE(0..100))read-writecurrent
dbuStatus
OBJECT-TYPE
This object is the identifier of the current Dial Backup Unit operating status. The values mean: dbuStatusDisabled The dial backup unit is either not installed or disabled dbuStatusEnabled The dial backup unit is installed and enabled dbuStatusActive The dial backup unit is currently active dbuStatusLocked The dial backup unit is in a locked state dbuStatusConnecting The dial backup unit is in the process of connecting dbuStatusDisallowed The dial backup unit is currently not allowed to activate due to the Time Of Day Enable settings dbuStatusAwaitingCall The dial backup unit is in the process of waiting for an incoming call dbuStatusDialing The dial backup unit is in the process of placing a call dbuStatusDisconnecting The dial backup unit is in the process of disconnecting dbuStatusTesting The dial backup unit is in the process of testing dbuStatusTestPassed The dial backup unit has passed a self-test dbuStatusTestFailed The dial backup unit has failed a self-test
1.3.6.1.4.1.321.100.2.2.1.1.9INTEGER {dbuStatusOther(1), dbuStatusDisabled(2), dbuStatusEnabled(3), dbuStatusActive(4), dbuStatusLocked(5), dbuStatusConnecting(6), dbuStatusDisallowed(7), dbuStatusAwaitingCall(8), dbuStatusDialing(9), dbuStatusDisconnecting(10), dbuStatusTesting(11), dbuStatusTestPassed(12), dbuStatusTestFailed(13)}read-onlycurrent
dbuCommand
OBJECT-TYPE
This object is the identifier of the current setting that the Dial Backup Unit is operating in. The values mean: dbuCommandDisable The dial backup unit is not to operate dbuCommandEnable The dial backup unit is to operate, subject to Activator and line conditions only dbuCommandActivate The dial backup unit is to operate, irregardless of line conditions dbuCommandLock The dial backup unit is to continue operating, irregardless of line conditions dbuCommandEnableDaily The dial backup unit is to operate, subject to Activator, line conditions, and the Time Of Day Enable fields dbuCommandTest The dial backup unit is commanded to test the link.
1.3.6.1.4.1.321.100.2.2.1.1.10INTEGER {dbuCommandOther(1), dbuCommandDisable(2), dbuCommandEnable(3), dbuCommandActivate(4), dbuCommandLock(5), dbuCommandEnableDaily(6), dbuCommandTest(7)}read-writecurrent
dbuActivator1
OBJECT-TYPE
This object is the identifier of the current trigger that will activate the Dial Backup Unit. The values mean: dbuActivatorLOS The dial backup unit is activated by a LOS alarm condition dbuActivatorOOS The dial backup unit is activated by an OOS alarm condition dbuActivatorOOF The dial backup unit is activated by an OOF alarm condition dbuActivatorAny The dial backup unit is activated by a LOS, OOS, or OOF alarm condition dbuActivatorES The dial backup unit is activated by an ES alarm condition dbuActivatorSES The dial backup unit is activated by an SES alarm condition dbuActivatorUAS The dial backup unit is activated by an UAS alarm condition dbuActivatorLOF The dial backup unit is activated by an LOF alarm condition dbuActivatorRAS The dial backup unit is activated by an RAS alarm condition dbuActivatorAIS The dial backup unit is activated by an AIS alarm condition dbuActivatorBPV The dial backup unit is activated by an BPV alarm condition
1.3.6.1.4.1.321.100.2.2.1.1.11INTEGER {dbuActivatorOther(1), dbuActivatorLOS(2), dbuActivatorOOS(3), dbuActivatorOOF(4), dbuActivatorAny(5), dbuActivatorES(6), dbuActivatorSES(7), dbuActivatorUAS(8), dbuActivatorLOF(9), dbuActivatorRAS(10), dbuActivatorAIS(11), dbuActivatorBPV(12)}read-writecurrent
dbuActivator2
OBJECT-TYPE
This object is the identifier of the current trigger that will activate the Dial Backup Unit. The values mean: dbuActivatorLOS The dial backup unit is activated by a LOS alarm condition dbuActivatorOOS The dial backup unit is activated by a OOS alarm condition dbuActivatorOOF The dial backup unit is activated by a OOF alarm condition dbuActivatorAny The dial backup unit is activated by a LOS, OOS, or OOF alarm condition dbuActivatorES The dial backup unit is activated by an ES alarm condition dbuActivatorSES The dial backup unit is activated by an SES alarm condition dbuActivatorUAS The dial backup unit is activated by an UAS alarm condition dbuActivatorLOF The dial backup unit is activated by an LOF alarm condition dbuActivatorRAS The dial backup unit is activated by an RAS alarm condition dbuActivatorAIS The dial backup unit is activated by an AIS alarm condition dbuActivatorBPV The dial backup unit is activated by an BPV alarm condition
1.3.6.1.4.1.321.100.2.2.1.1.12INTEGER {dbuActivatorOther(1), dbuActivatorLOS(2), dbuActivatorOOS(3), dbuActivatorOOF(4), dbuActivatorAny(5), dbuActivatorES(6), dbuActivatorSES(7), dbuActivatorUAS(8), dbuActivatorLOF(9), dbuActivatorRAS(10), dbuActivatorAIS(11), dbuActivatorBPV(12)}read-writecurrent
dbuDialStr
OBJECT-TYPE
This string is the dial string sent to the dial backup unit during every connection attempt
1.3.6.1.4.1.321.100.2.2.1.1.13DisplayString (SIZE(0..50))read-writecurrent
dbuInitStr
OBJECT-TYPE
This string is the initialization string sent to the dial backup unit before every connection attempt
1.3.6.1.4.1.321.100.2.2.1.1.14DisplayString (SIZE(0..50))read-writecurrent
dbuHangupStr
OBJECT-TYPE
This string is the hangup command string sent to the dial backup unit after every successful call
1.3.6.1.4.1.321.100.2.2.1.1.15DisplayString (SIZE(0..50))read-writecurrent
dbuPasswordStr
OBJECT-TYPE
This string is the prompt character and password string for the dial backup unit in Callback DBU
1.3.6.1.4.1.321.100.2.2.1.1.16DisplayString (SIZE(0..8))read-writecurrent
dbuSecurity
OBJECT-TYPE
Enables security on dial backup unit.
1.3.6.1.4.1.321.100.2.2.1.1.17INTEGER {dbuSecurityOther(1), dbuSecurityDisable(2), dbuSecurityEnable(3)}read-writecurrent
dbuDtrDial
OBJECT-TYPE
Enables DTR dial feature on dial backup unit.
1.3.6.1.4.1.321.100.2.2.1.1.18INTEGER {dbuDtrDialOther(1), dbuDtrDialDisable(2), dbuDtrDialEnable(3)}read-writecurrent
dbuISDNSwitchType
OBJECT-TYPE
Specifies the switch type for the ISDN DBU.
1.3.6.1.4.1.321.100.2.2.1.1.19INTEGERread-writecurrent
dbuISDNSwitchVersion
OBJECT-TYPE
Specifies the switch version for the ISDN DBU.
1.3.6.1.4.1.321.100.2.2.1.1.20INTEGER {dbuISDNSwitchVersionOther(1), dbuISDNSwitchVersionNational1(2), dbuISDNSwitchVersionATTP2P(3), dbuISDNSwitchVersionATTMP(4), dbuISDNSwitchVersionDMS100PVCIC0(5), dbuISDNSwitchVersionDMS100PVCIC1(6)}read-writecurrent
dbuISDNTEI
OBJECT-TYPE
Specifies the ISDN DBU TEI.
1.3.6.1.4.1.321.100.2.2.1.1.21INTEGER {dbuISDNTEIOther(1), dbuISDNTEIDisable(2), dbuISDNTEIAuto(3), dbuISDNTEI0(4), dbuISDNTEI1(5), dbuISDNTEI2(6), dbuISDNTEI3(7), dbuISDNTEI4(8), dbuISDNTEI5(9), dbuISDNTEI6(10), dbuISDNTEI7(11), dbuISDNTEI8(12), dbuISDNTEI9(13), dbuISDNTEI10(14), dbuISDNTEI11(15), dbuISDNTEI12(16), dbuISDNTEI13(17), dbuISDNTEI14(18), dbuISDNTEI15(19), dbuISDNTEI16(20), dbuISDNTEI17(21), dbuISDNTEI18(22), dbuISDNTEI19(23), dbuISDNTEI20(24), dbuISDNTEI21(25), dbuISDNTEI22(26), dbuISDNTEI23(27), dbuISDNTEI24(28), dbuISDNTEI25(29), dbuISDNTEI26(30), dbuISDNTEI27(31), dbuISDNTEI28(32), dbuISDNTEI29(33), dbuISDNTEI30(34), dbuISDNTEI31(35), dbuISDNTEI32(36), dbuISDNTEI33(37), dbuISDNTEI34(38), dbuISDNTEI35(39), dbuISDNTEI36(40), dbuISDNTEI37(41), dbuISDNTEI38(42), dbuISDNTEI39(43), dbuISDNTEI40(44), dbuISDNTEI41(45), dbuISDNTEI42(46), dbuISDNTEI43(47), dbuISDNTEI44(48), dbuISDNTEI45(49), dbuISDNTEI46(50), dbuISDNTEI47(51), dbuISDNTEI48(52), dbuISDNTEI49(53), dbuISDNTEI50(54), dbuISDNTEI51(55), dbuISDNTEI52(56), dbuISDNTEI53(57), dbuISDNTEI54(58), dbuISDNTEI55(59), dbuISDNTEI56(60), dbuISDNTEI57(61), dbuISDNTEI58(62), dbuISDNTEI59(63), dbuISDNTEI60(64), dbuISDNTEI61(65), dbuISDNTEI62(66), dbuISDNTEI63(67)}read-writecurrent
dbuISDNSPID
OBJECT-TYPE
Specifies the SPID for the ISDN DBU.
1.3.6.1.4.1.321.100.2.2.1.1.22DisplayString (SIZE(0..20))read-writecurrent
dbuISDNDDNUM
OBJECT-TYPE
Specifies the Data Directory Number for the ISDN DBU.
1.3.6.1.4.1.321.100.2.2.1.1.23DisplayString (SIZE(0..20))read-writecurrent
dbuResetStringsTable
OBJECT-TYPE
A table of COLD START reprogramming strings for the dial backup unit.
1.3.6.1.4.1.321.100.2.2.2not-accessiblecurrent
dbuResetStringsEntry
OBJECT-TYPE
An entry in the dbuResetStringsTable.
1.3.6.1.4.1.321.100.2.2.2.1not-accessiblecurrent
dbuResetNearIndex
OBJECT-TYPE
Selects the near device.
1.3.6.1.4.1.321.100.2.2.2.1.1INTEGERread-onlycurrent
dbuResetFarIndex
OBJECT-TYPE
Selects the far device.
1.3.6.1.4.1.321.100.2.2.2.1.2INTEGERread-onlycurrent
dbuResetConfigEntryIndex
OBJECT-TYPE
The index into the Dial Backup table.
1.3.6.1.4.1.321.100.2.2.2.1.3INTEGERread-onlycurrent
dbuResetStringsIndex
OBJECT-TYPE
The index into the dbuResetStringsTable.
1.3.6.1.4.1.321.100.2.2.2.1.4INTEGERread-onlycurrent
dbuResetString
OBJECT-TYPE
This string is one of the dial backup unit's COLD START reprogramming strings
1.3.6.1.4.1.321.100.2.2.2.1.5DisplayString (SIZE(0..50))read-writecurrent
dbuStartStopTable
OBJECT-TYPE
The Dial Backup StartStop Table.
1.3.6.1.4.1.321.100.2.2.3not-accessiblecurrent
dbuStartStopTableEntry
OBJECT-TYPE
An entry in the Dial Backup Start Stop table.
1.3.6.1.4.1.321.100.2.2.3.1not-accessiblecurrent
dbuStartStopNearIndex
OBJECT-TYPE
Selects the near device.
1.3.6.1.4.1.321.100.2.2.3.1.1INTEGERread-onlycurrent
dbuStartStopFarIndex
OBJECT-TYPE
Selects the far device.
1.3.6.1.4.1.321.100.2.2.3.1.2INTEGERread-onlycurrent
dbuStartStopConfigEntryIndex
OBJECT-TYPE
The index into the Dial Backup table.
1.3.6.1.4.1.321.100.2.2.3.1.3INTEGERread-onlycurrent
dbuStartStopDayOfWeek
OBJECT-TYPE
The index into the Dial Backup Start Stop times table.
1.3.6.1.4.1.321.100.2.2.3.1.4INTEGER {dbuStartStopSunday(1), dbuStartStopMonday(2), dbuStartStopTuesday(3), dbuStartStopWednesday(4), dbuStartStopThursday(5), dbuStartStopFriday(6), dbuStartStopSaturday(7)}read-onlycurrent
dbuStart
OBJECT-TYPE
This object is the beginning of an allowable window for Dial Backup Activation.
1.3.6.1.4.1.321.100.2.2.3.1.5INTEGER {dbuStartHour00(1), dbuStartHour01(2), dbuStartHour02(3), dbuStartHour03(4), dbuStartHour04(5), dbuStartHour05(6), dbuStartHour06(7), dbuStartHour07(8), dbuStartHour08(9), dbuStartHour09(10), dbuStartHour10(11), dbuStartHour11(12), dbuStartHour12(13), dbuStartHour13(14), dbuStartHour14(15), dbuStartHour15(16), dbuStartHour16(17), dbuStartHour17(18), dbuStartHour18(19), dbuStartHour19(20), dbuStartHour20(21), dbuStartHour21(22), dbuStartHour22(23), dbuStartHour23(24)}read-writecurrent
dbuStop
OBJECT-TYPE
This object is the end of an allowable window for Dial Backup Activation.
1.3.6.1.4.1.321.100.2.2.3.1.6INTEGER {dbuStopHour00(1), dbuStopHour01(2), dbuStopHour02(3), dbuStopHour03(4), dbuStopHour04(5), dbuStopHour05(6), dbuStopHour06(7), dbuStopHour07(8), dbuStopHour08(9), dbuStopHour09(10), dbuStopHour10(11), dbuStopHour11(12), dbuStopHour12(13), dbuStopHour13(14), dbuStopHour14(15), dbuStopHour15(16), dbuStopHour16(17), dbuStopHour17(18), dbuStopHour18(19), dbuStopHour19(20), dbuStopHour20(21), dbuStopHour21(22), dbuStopHour22(23), dbuStopHour23(24)}read-writecurrent
t1e1
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.2.3
t1e1ConfigTable
OBJECT-TYPE
The T1 and E1 Configuration Table.
1.3.6.1.4.1.321.100.2.3.1not-accessiblecurrent
t1e1ConfigTableEntry
OBJECT-TYPE
An entry in the t1e1Table.
1.3.6.1.4.1.321.100.2.3.1.1not-accessiblecurrent
t1e1ConfigNearIndex
OBJECT-TYPE
Selects the near device.
1.3.6.1.4.1.321.100.2.3.1.1.1INTEGERread-onlycurrent
t1e1ConfigFarIndex
OBJECT-TYPE
Selects the far device.
1.3.6.1.4.1.321.100.2.3.1.1.2INTEGERread-onlycurrent
t1e1ConfigIndex
OBJECT-TYPE
This object is the index into the t1e1Table.
1.3.6.1.4.1.321.100.2.3.1.1.3INTEGERread-onlycurrent
t1e1Description
OBJECT-TYPE
Contains a textual description of the port.
1.3.6.1.4.1.321.100.2.3.1.1.4DisplayString (SIZE(0..40))read-onlycurrent
t1e1Mode
OBJECT-TYPE
This object identifies the port as either a Network (long-haul) or DTE (short-haul) port.
1.3.6.1.4.1.321.100.2.3.1.1.5INTEGER {t1e1ModeOther(1), t1e1ModeDTE(2), t1e1ModeNetwork(3)}read-writecurrent
t1e1FrameType
OBJECT-TYPE
Selects the framing for the network side of the DSU/CSU.
1.3.6.1.4.1.321.100.2.3.1.1.6INTEGER {t1e1FrameTypeOther(1), t1e1FrameTypeESF(2), t1e1FrameTypeD4(3), t1e1FrameTypeCCSCRC(4), t1e1FrameTypeCCS(5), t1e1FrameTypeCAS(6), t1e1FrameTypeCASCRC(7), t1e1FrameTypeUnframed(8), t1e1FrameTypeV3(9), t1e1FrameTypeT1Unframed(10)}read-writecurrent
t1e1LineCode
OBJECT-TYPE
Selects the network side line coding.
1.3.6.1.4.1.321.100.2.3.1.1.7INTEGER {t1e1LineCodeOther(1), t1e1LineCodeAMI(2), t1e1LineCodeB8ZS(3), t1e1LineCodeHDB3(4)}read-writecurrent
t1e1LineBuildOut
OBJECT-TYPE
Selects the line build out for the network interface. The options are: t1e1LineBuildOut0db indicates a line build out of 0db t1e1LineBuildOut75db indicates a line build out of -7.5db t1e1LineBuildOut15db indicates a line build out of -15db t1e1LineBuildOut225db indicates a line build out of -22.5db
1.3.6.1.4.1.321.100.2.3.1.1.8INTEGER {t1e1LineBuildOutOther(1), t1e1LineBuildOut0db(2), t1e1LineBuildOut75db(3), t1e1LineBuildOut15db(4), t1e1LineBuildOut225db(5)}read-writecurrent
t1e1Timing
OBJECT-TYPE
Sets the timing source to synchronize the unit's internal timing generators.
1.3.6.1.4.1.321.100.2.3.1.1.9INTEGER {t1e1TimingOther(1), t1e1TimingInternal(2), t1e1TimingNetwork(3), t1e1TimingT1DTE(4), t1e1TimingStation(5), t1e1TimingStaClock(6), t1e1TimingPort1(7), t1e1TimingPort2(8), t1e1TimingPort3(9), t1e1TimingPort4(10), t1e1TimingPort5(11), t1e1TimingPort6(12), t1e1TimingPort7(13), t1e1TimingPort8(14), t1e1TimingPort9(15), t1e1TimingPort10(16), t1e1TimingPort11(17), t1e1TimingPort12(18), t1e1TimingPort13(19), t1e1TimingPort14(20), t1e1TimingPort15(21), t1e1TimingPort16(22), t1e1TimingPort17(23), t1e1TimingPort18(24), t1e1TimingPort19(25), t1e1TimingPort20(26), t1e1TimingPort21(27), t1e1TimingPort22(28), t1e1TimingPort23(29), t1e1TimingPort24(30), t1e1TimingPort25(31), t1e1TimingPort26(32), t1e1TimingPort27(33), t1e1TimingPort28(34), t1e1TimingPort29(35), t1e1TimingPort30(36), t1e1TimingPort31(37), t1e1TimingPort32(38), t1e1TimingSlot2PortA(39), t1e1TimingSlot2PortB(40), t1e1TimingSlot3PortA(41), t1e1TimingSlot3PortB(42), t1e1TimingSlot4PortA(43), t1e1TimingSlot4PortB(44), t1e1TimingSlot5PortA(45), t1e1TimingSlot5PortB(46), t1e1TimingSlot6PortA(47), t1e1TimingSlot6PortB(48), t1e1TimingSlot2Dsu1PortA(49), t1e1TimingSlot2Dsu1PortB(50), t1e1TimingSlot2Dsu2PortA(51), t1e1TimingSlot2Dsu2PortB(52), t1e1TimingSlot2Dsu3PortA(53), t1e1TimingSlot2Dsu3PortB(54), t1e1TimingSlot2Dsu4PortA(55), t1e1TimingSlot2Dsu4PortB(56), t1e1TimingSlot2Dsu5PortA(57), t1e1TimingSlot2Dsu5PortB(58), t1e1TimingSlot2Dsu6PortA(59), t1e1TimingSlot2Dsu6PortB(60), t1e1TimingSlot3Dsu1PortA(61), t1e1TimingSlot3Dsu1PortB(62), t1e1TimingSlot3Dsu2PortA(63), t1e1TimingSlot3Dsu2PortB(64), t1e1TimingSlot3Dsu3PortA(65), t1e1TimingSlot3Dsu3PortB(66), t1e1TimingSlot3Dsu4PortA(67), t1e1TimingSlot3Dsu4PortB(68), t1e1TimingSlot3Dsu5PortA(69), t1e1TimingSlot3Dsu5PortB(70), t1e1TimingSlot3Dsu6PortA(71), t1e1TimingSlot3Dsu6PortB(72), t1e1TimingSlot4Dsu1PortA(73), t1e1TimingSlot4Dsu1PortB(74), t1e1TimingSlot4Dsu2PortA(75), t1e1TimingSlot4Dsu2PortB(76), t1e1TimingSlot4Dsu3PortA(77), t1e1TimingSlot4Dsu3PortB(78), t1e1TimingSlot4Dsu4PortA(79), t1e1TimingSlot4Dsu4PortB(80), t1e1TimingSlot4Dsu5PortA(81), t1e1TimingSlot4Dsu5PortB(82), t1e1TimingSlot4Dsu6PortA(83), t1e1TimingSlot4Dsu6PortB(84), t1e1TimingSlot5Dsu1PortA(85), t1e1TimingSlot5Dsu1PortB(86), t1e1TimingSlot5Dsu2PortA(87), t1e1TimingSlot5Dsu2PortB(88), t1e1TimingSlot5Dsu3PortA(89), t1e1TimingSlot5Dsu3PortB(90), t1e1TimingSlot5Dsu4PortA(91), t1e1TimingSlot5Dsu4PortB(92), t1e1TimingSlot5Dsu5PortA(93), t1e1TimingSlot5Dsu5PortB(94), t1e1TimingSlot5Dsu6PortA(95), t1e1TimingSlot5Dsu6PortB(96), t1e1TimingSlot6Dsu1PortA(97), t1e1TimingSlot6Dsu1PortB(98), t1e1TimingSlot6Dsu2PortA(99), t1e1TimingSlot6Dsu2PortB(100), t1e1TimingSlot6Dsu3PortA(101), t1e1TimingSlot6Dsu3PortB(102), t1e1TimingSlot6Dsu4PortA(103), t1e1TimingSlot6Dsu4PortB(104), t1e1TimingSlot6Dsu5PortA(105), t1e1TimingSlot6Dsu5PortB(106), t1e1TimingSlot6Dsu6PortA(107), t1e1TimingSlot6Dsu6PortB(108)}read-writecurrent
t1e1StationInTiming
OBJECT-TYPE
Selects the input timing if t1e1Timing is set to Station.
1.3.6.1.4.1.321.100.2.3.1.1.10INTEGER {t1e1StationInTimingOther(1), t1e1StationInTimingNX56(2), t1e1StationInTimingNX64(3), t1e1StationInTiming1544(4), t1e1StationInTiming2048(5)}read-writecurrent
t1e1StationTiming
OBJECT-TYPE
Selects the N-multiple when Station Input Timing is set to either NX56 or NX65. The N range is 1..24
1.3.6.1.4.1.321.100.2.3.1.1.11INTEGERread-writecurrent
t1e1PRM
OBJECT-TYPE
Enables the ANSI T1.403 Performance Report Message functions.
1.3.6.1.4.1.321.100.2.3.1.1.12INTEGER {t1e1PRMOther(1), t1e1PRMDisable(2), t1e1PRMEnable(3)}read-writecurrent
t1e1ZeroSuppress
OBJECT-TYPE
Determines whether ones density insertion is activated after 15 zeros . To ensure compliance with TR54016, this field must be enabled.
1.3.6.1.4.1.321.100.2.3.1.1.13INTEGER {t1e1ZeroOther(1), t1e1ZeroDisable(2), t1e1ZeroEnable(3)}read-writecurrent
t1e1NationalBit
OBJECT-TYPE
Selects a national bit to create a 4-kbps datalink between the endpoint units.
1.3.6.1.4.1.321.100.2.3.1.1.14INTEGER {t1e1NationalOther(1), t1e1NationalNone(2), t1e1NationalSA4(3), t1e1NationalSA5(4), t1e1NationalSA6(5), t1e1NationalSA7(6), t1e1NationalSA8(7)}read-writecurrent
t1e1KeepAlive
OBJECT-TYPE
Selects keep alive framed and unframed ones when the unit detects LOS or OOF.
1.3.6.1.4.1.321.100.2.3.1.1.15INTEGER {t1e1KeepAliveOther(1), t1e1KeepAliveUnframedOnes(2), t1e1KeepAliveFramedOnes(3), t1e1KeepAliveLoop(4)}read-writecurrent
t1e1CRC4Mode
OBJECT-TYPE
Selects whether CRC4 is enabled or disabled.
1.3.6.1.4.1.321.100.2.3.1.1.16INTEGER {t1e1CRC4Other(1), t1e1CRC4Disabled(2), t1e1CRC4Enabled(3)}read-writecurrent
t1e1DSXLevel
OBJECT-TYPE
Selects the DSX1 interface output level.
1.3.6.1.4.1.321.100.2.3.1.1.17INTEGER {t1e1DSXOther(1), t1e1DSX0110(2), t1e1DSX111220(3), t1e1DSX221330(4), t1e1DSX331440(5), t1e1DSX441550(6), t1e1DSX551660(7), t1e1DSX661up(8)}read-writecurrent
t1e1CRC
OBJECT-TYPE
Determines whether received CRC data is passed through or regenerated.
1.3.6.1.4.1.321.100.2.3.1.1.18INTEGER {t1e1CRCOther(1), t1e1CRCPass(2), t1e1CRCRegenerate(3)}read-writecurrent
t1e1FDLPassThrough
OBJECT-TYPE
Determines whether the ESF FDL passes through the CSU or terminates.
1.3.6.1.4.1.321.100.2.3.1.1.19INTEGER {t1e1FDLPassThroughOther(1), t1e1FDLPassThroughPass(2), t1e1FDLPassThroughTerminate(3)}read-writecurrent
t1e1AudibleAlarm
OBJECT-TYPE
If applicable, Enables or Disables the CSU's internal buzzer which alerts users of an alarm condition.
1.3.6.1.4.1.321.100.2.3.1.1.20INTEGER {t1e1AudibleAlarmOther(1), t1e1AudibleAlarmDisabled(2), t1e1AudibleAlarmEnabled(3)}read-writecurrent
t1e1Function
OBJECT-TYPE
Specifies the function the network port will perform in the unit. The options are: t1e1FunctionNetwork (Independent network port) t1e1FunctionSlaved (Slaved to another network port) t1e1FunctionBackup (Automatic Protection Switching Backup for another network port)
1.3.6.1.4.1.321.100.2.3.1.1.21INTEGER {t1e1FunctionOther(1), t1e1FunctionNetwork(2), t1e1FunctionSlaved(3), t1e1FunctionBackup(4)}read-writecurrent
t1e1EBitGeneration
OBJECT-TYPE
1.3.6.1.4.1.321.100.2.3.1.1.22INTEGER {other(1), disabled(2), enabled(3)}read-writecurrent
t1e1RAIGeneration
OBJECT-TYPE
1.3.6.1.4.1.321.100.2.3.1.1.23INTEGER {other(1), disabled(2), enabled(3)}read-writecurrent
t1e1SpareBitInsertion
OBJECT-TYPE
1.3.6.1.4.1.321.100.2.3.1.1.24INTEGER {other(1), disabled(2), enabled(3)}read-writecurrent
t1e1Sa4In
OBJECT-TYPE
1.3.6.1.4.1.321.100.2.3.1.1.25OCTET STRING (SIZE(8))read-onlycurrent
t1e1Sa5In
OBJECT-TYPE
1.3.6.1.4.1.321.100.2.3.1.1.26OCTET STRING (SIZE(8))read-onlycurrent
t1e1Sa6In
OBJECT-TYPE
1.3.6.1.4.1.321.100.2.3.1.1.27OCTET STRING (SIZE(8))read-onlycurrent
t1e1Sa7In
OBJECT-TYPE
1.3.6.1.4.1.321.100.2.3.1.1.28OCTET STRING (SIZE(8))read-onlycurrent
t1e1Sa8In
OBJECT-TYPE
1.3.6.1.4.1.321.100.2.3.1.1.29OCTET STRING (SIZE(8))read-onlycurrent
t1e1Sa4Out
OBJECT-TYPE
1.3.6.1.4.1.321.100.2.3.1.1.30OCTET STRING (SIZE(8))read-writecurrent
t1e1Sa5Out
OBJECT-TYPE
1.3.6.1.4.1.321.100.2.3.1.1.31OCTET STRING (SIZE(8))read-writecurrent
t1e1Sa6Out
OBJECT-TYPE
1.3.6.1.4.1.321.100.2.3.1.1.32OCTET STRING (SIZE(8))read-writecurrent
t1e1Sa7Out
OBJECT-TYPE
1.3.6.1.4.1.321.100.2.3.1.1.33OCTET STRING (SIZE(8))read-writecurrent
t1e1Sa8Out
OBJECT-TYPE
1.3.6.1.4.1.321.100.2.3.1.1.34OCTET STRING (SIZE(8))read-writecurrent
t1e1AlarmTable
OBJECT-TYPE
The T1 and E1 Alarm Table.
1.3.6.1.4.1.321.100.2.3.2not-accessiblecurrent
t1e1AlarmTableEntry
OBJECT-TYPE
An entry in the t1e1Table.
1.3.6.1.4.1.321.100.2.3.2.1not-accessiblecurrent
t1e1AlarmNearIndex
OBJECT-TYPE
Selects the near device.
1.3.6.1.4.1.321.100.2.3.2.1.1INTEGERread-onlycurrent
t1e1AlarmFarIndex
OBJECT-TYPE
Selects the far device.
1.3.6.1.4.1.321.100.2.3.2.1.2INTEGERread-onlycurrent
t1e1AlarmIndex
OBJECT-TYPE
This object is the index into the t1e1Table.
1.3.6.1.4.1.321.100.2.3.2.1.3INTEGERread-onlycurrent
t1e1StatusSummary
OBJECT-TYPE
This object provides a summary of the port status.
1.3.6.1.4.1.321.100.2.3.2.1.4DisplayString (SIZE(0..80))read-onlycurrent
t1e1AlarmSummary
OBJECT-TYPE
This object provides a summary of the port alarms.
1.3.6.1.4.1.321.100.2.3.2.1.5DisplayString (SIZE(0..80))read-onlycurrent
t1e1ESStatus
OBJECT-TYPE
Reports if an Errored Second condition exists.
1.3.6.1.4.1.321.100.2.3.2.1.6INTEGER {t1e1StatusOther(1), t1e1StatusNoES(2), t1e1StatusES(3)}read-onlycurrent
t1e1ESCount
OBJECT-TYPE
This count contains the number of consecutive seconds an Errored Second condition has existed.
1.3.6.1.4.1.321.100.2.3.2.1.7INTEGERread-onlycurrent
t1e1ESThreshold
OBJECT-TYPE
Sets the Errored Seconds alarm threshold. Setting this field to 0 disables the alarm. The threshold can be set to any value in the range 0 to 900.
1.3.6.1.4.1.321.100.2.3.2.1.8INTEGERread-writecurrent
t1e1ESAlarm
OBJECT-TYPE
This status indicates if the Errors Seconds threshold is exceeded.
1.3.6.1.4.1.321.100.2.3.2.1.9INTEGER {t1e1ESAlarmOther(1), t1e1ESAlarmNone(2), t1e1ESAlarmThresholdExceeded(3)}read-onlycurrent
t1e1SESStatus
OBJECT-TYPE
Reports if a Severely Errored condition exists.
1.3.6.1.4.1.321.100.2.3.2.1.10INTEGER {t1e1StatusOther(1), t1e1StatusNoSES(2), t1e1StatusSES(3)}read-onlycurrent
t1e1SESCount
OBJECT-TYPE
This count contains the number of consecutive seconds a Severely Errored condition has existed.
1.3.6.1.4.1.321.100.2.3.2.1.11INTEGERread-onlycurrent
t1e1SESThreshold
OBJECT-TYPE
Sets the Severely Errored seconds alarm threshold. Setting this field to 0 disables the alarm. The threshold can be set to any value in the range 0 to 900.
1.3.6.1.4.1.321.100.2.3.2.1.12INTEGERread-writecurrent
t1e1SESAlarm
OBJECT-TYPE
This status indicates if the Severely Errors Seconds threshold is exceeded.
1.3.6.1.4.1.321.100.2.3.2.1.13INTEGER {t1e1SESAlarmOther(1), t1e1SESAlarmNone(2), t1e1SESAlarmThresholdExceeded(3)}read-onlycurrent
t1e1LOSSStatus
OBJECT-TYPE
Reports if a Loss of Signal condition exists.
1.3.6.1.4.1.321.100.2.3.2.1.14INTEGER {t1e1StatusOther(1), t1e1StatusNoLOSS(2), t1e1StatusLOSS(3)}read-onlycurrent
t1e1LOSSCount
OBJECT-TYPE
This count contains the number of consecutive seconds a Loss of Signal condition has existed.
1.3.6.1.4.1.321.100.2.3.2.1.15INTEGERread-onlycurrent
t1e1LOSSThreshold
OBJECT-TYPE
Sets the Loss of Signal seconds alarm threshold. Setting this field to 0 disables the alarm. The threshold can be set to any value in the range 0 to 900.
1.3.6.1.4.1.321.100.2.3.2.1.16INTEGERread-writecurrent
t1e1LOSSAlarm
OBJECT-TYPE
This status indicates if the Loss of Signal Seconds threshold is exceeded.
1.3.6.1.4.1.321.100.2.3.2.1.17INTEGER {t1e1LOSSAlarmOther(1), t1e1LOSSAlarmNone(2), t1e1LOSSAlarmThresholdExceeded(3)}read-onlycurrent
t1e1UASStatus
OBJECT-TYPE
Reports if an Unavailable condition exists.
1.3.6.1.4.1.321.100.2.3.2.1.18INTEGER {t1e1StatusOther(1), t1e1StatusNoUAS(2), t1e1StatusUAS(3)}read-onlycurrent
t1e1UASCount
OBJECT-TYPE
This count contains the number of consecutive seconds an Unavailable condition has existed.
1.3.6.1.4.1.321.100.2.3.2.1.19INTEGERread-onlycurrent
t1e1UASThreshold
OBJECT-TYPE
Sets the unavailable seconds alarm threshold. Setting this field to 0 disables the alarm. The threshold can be set to any value in the range 0 to 900.
1.3.6.1.4.1.321.100.2.3.2.1.20INTEGERread-writecurrent
t1e1UASAlarm
OBJECT-TYPE
This status indicates if the Unavailable Seconds threshold is exceeded.
1.3.6.1.4.1.321.100.2.3.2.1.21INTEGER {t1e1UASAlarmOther(1), t1e1UASAlarmNone(2), t1e1UASAlarmThresholdExceeded(3)}read-onlycurrent
t1e1CSSStatus
OBJECT-TYPE
Reports if a Controlled Slip condition exists.
1.3.6.1.4.1.321.100.2.3.2.1.22INTEGER {t1e1StatusOther(1), t1e1StatusNoCSS(2), t1e1StatusCSS(3)}read-onlycurrent
t1e1CSSCount
OBJECT-TYPE
This count contains the number of consecutive seconds in which at least one Controlled Slip occurred.
1.3.6.1.4.1.321.100.2.3.2.1.23INTEGERread-onlycurrent
t1e1CSSThreshold
OBJECT-TYPE
Sets the Controlled Slip seconds alarm threshold. Setting this field to 0 disables the alarm. The threshold can be set to any value in the range 0 to 900.
1.3.6.1.4.1.321.100.2.3.2.1.24INTEGERread-writecurrent
t1e1CSSAlarm
OBJECT-TYPE
This status indicates if the Controlled Slip seconds threshold is exceeded.
1.3.6.1.4.1.321.100.2.3.2.1.25INTEGER {t1e1CSSAlarmOther(1), t1e1CSSAlarmNone(2), t1e1CSSAlarmThresholdExceeded(3)}read-onlycurrent
t1e1BPVSStatus
OBJECT-TYPE
Reports if a Bipolar Violation Error condition exists.
1.3.6.1.4.1.321.100.2.3.2.1.26INTEGER {t1e1StatusOther(1), t1e1StatusNoBPVS(2), t1e1StatusBPVS(3)}read-onlycurrent
t1e1BPVSCount
OBJECT-TYPE
This count contains the number of consecutive seconds a Bipolar Violation Error condition has existed.
1.3.6.1.4.1.321.100.2.3.2.1.27INTEGERread-onlycurrent
t1e1BPVSThreshold
OBJECT-TYPE
Sets the Bipolar Violation Error seconds alarm threshold. Setting this field to 0 disables the alarm. The threshold can be set to any value in the range 0 to 900.
1.3.6.1.4.1.321.100.2.3.2.1.28INTEGERread-writecurrent
t1e1BPVSAlarm
OBJECT-TYPE
This status indicates if the Bipolar Violation Error seconds threshold is exceeded.
1.3.6.1.4.1.321.100.2.3.2.1.29INTEGER {t1e1BPVSAlarmOther(1), t1e1BPVSAlarmNone(2), t1e1BPVSAlarmThresholdExceeded(3)}read-onlycurrent
t1e1OOFSStatus
OBJECT-TYPE
Indicates that the unit is unable to synchronize on the incoming framing pattern.
1.3.6.1.4.1.321.100.2.3.2.1.30INTEGER {t1e1StatusOther(1), t1e1StatusNoOOF(2), t1e1StatusOOF(3)}read-onlycurrent
t1e1OOFSCount
OBJECT-TYPE
This count contains the number of consecutive seconds an OOF condition has existed.
1.3.6.1.4.1.321.100.2.3.2.1.31INTEGERread-onlycurrent
t1e1OOFSThreshold
OBJECT-TYPE
Sets the OOF seconds alarm threshold. Setting this field to 0 disables the alarm. The threshold can be set to any value in the range 0 to 900.
1.3.6.1.4.1.321.100.2.3.2.1.32INTEGERread-writecurrent
t1e1OOFSAlarm
OBJECT-TYPE
Indicates if an OOF seconds alarm condition exists.
1.3.6.1.4.1.321.100.2.3.2.1.33INTEGER {t1e1OOFSAlarmOther(1), t1e1OOFSAlarmNone(2), t1e1OOFSAlarmExists(3)}read-onlycurrent
t1e1AISStatus
OBJECT-TYPE
Indicates that the unit is receiving an unframed all ones pattern.
1.3.6.1.4.1.321.100.2.3.2.1.34INTEGER {t1e1StatusOther(1), t1e1StatusNoAIS(2), t1e1StatusAIS(3)}read-onlycurrent
t1e1AISCount
OBJECT-TYPE
This count contains the number of consecutive seconds an Unframed All Ones condition has existed.
1.3.6.1.4.1.321.100.2.3.2.1.35INTEGERread-onlycurrent
t1e1AISThreshold
OBJECT-TYPE
Sets the AIS seconds alarm threshold. Setting this field to 0 disables the alarm. The threshold can be set to any value in the range 0 to 900.
1.3.6.1.4.1.321.100.2.3.2.1.36INTEGERread-writecurrent
t1e1AISAlarm
OBJECT-TYPE
Indicates if an Unframed All Ones alarm condition exists.
1.3.6.1.4.1.321.100.2.3.2.1.37INTEGER {t1e1AISAlarmOther(1), t1e1AISAlarmNone(2), t1e1AISAlarmExists(3)}read-onlycurrent
t1e1RASStatus
OBJECT-TYPE
Reports if a Remote (Yellow) Alarm condition exists.
1.3.6.1.4.1.321.100.2.3.2.1.38INTEGER {t1e1RASStatusOther(1), t1e1RASStatusNoRAS(2), t1e1RASStatusRAS(3)}read-onlycurrent
t1e1RASCount
OBJECT-TYPE
This count contains the number of consecutive seconds a Remote (Yellow) Alarm condition has existed.
1.3.6.1.4.1.321.100.2.3.2.1.39INTEGERread-onlycurrent
t1e1RASThreshold
OBJECT-TYPE
Sets the RAS seconds alarm threshold. Setting this field to 0 disables the alarm. The threshold can be set to any value in the range 0 to 900.
1.3.6.1.4.1.321.100.2.3.2.1.40INTEGERread-writecurrent
t1e1RASAlarm
OBJECT-TYPE
This status indicates if a Remote (Yellow) Alarm exists.
1.3.6.1.4.1.321.100.2.3.2.1.41INTEGER {t1e1RASAlarmOther(1), t1e1RASAlarmNone(2), t1e1RASAlarmExists(3)}read-onlycurrent
t1e1AlarmResetTimer
OBJECT-TYPE
Sets the Alarm Reset Timer, this field can be set to any value in the range 0 to 900.
1.3.6.1.4.1.321.100.2.3.2.1.42INTEGERread-writecurrent
t1e1AlarmReset
OBJECT-TYPE
This is used to clear the current alarm counts.
1.3.6.1.4.1.321.100.2.3.2.1.43INTEGER {t1e1AlarmResetOther(1), t1e1AlarmResetClearAlarms(2)}read-writecurrent
ddsNet
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.2.4
ddsNetConfigTable
OBJECT-TYPE
The dds Network Interface Configuration Table.
1.3.6.1.4.1.321.100.2.4.1not-accessiblecurrent
ddsNetConfigTableEntry
OBJECT-TYPE
An entry in the Network Interface Table.
1.3.6.1.4.1.321.100.2.4.1.1not-accessiblecurrent
ddsNetConfigNearIndex
OBJECT-TYPE
Selects the near device.
1.3.6.1.4.1.321.100.2.4.1.1.1INTEGERread-onlycurrent
ddsNetConfigFarIndex
OBJECT-TYPE
Selects the far device.
1.3.6.1.4.1.321.100.2.4.1.1.2INTEGERread-onlycurrent
ddsNetConfigIndex
OBJECT-TYPE
Index into the ddsNetConfigTable.
1.3.6.1.4.1.321.100.2.4.1.1.3INTEGERread-onlycurrent
ddsNetDescription
OBJECT-TYPE
Contains a textual description of the port.
1.3.6.1.4.1.321.100.2.4.1.1.4DisplayString (SIZE(0..40))read-writecurrent
ddsNetRate
OBJECT-TYPE
This object is the identifier of the current DDS network rate. The values mean: ddsNetRate2400 the DDS network interface is operating at 2400bps ddsNetRate4800 the DDS network interface is operating at 4800bps ddsNetRate9600 the DDS network interface is operating at 9600bps ddsNetRate19200 the DDS network interface is operating at 19200bps ddsNetRate38400 the DDS network interface is operating at 38400bps ddsNetRate56000 the DDS network interface is operating at 56000bps ddsNetRate64000 the DDS network interface is operating at 64000bps
1.3.6.1.4.1.321.100.2.4.1.1.5INTEGER {ddsNetRate2400(1), ddsNetRate4800(2), ddsNetRate9600(3), ddsNetRate19200(4), ddsNetRate38400(5), ddsNetRate56000(6), ddsNetRate64000(7)}read-writecurrent
ddsNetMode
OBJECT-TYPE
This variable describes mode in which data is being sent from the DDS unit back towards the network. Changing the value of this variable can cause a loss of remote communications. The values mean: ddsNetModeNormal (DDS-I) normal data mode of operation ddsNetModeProprietaryTXPI (DDS-I) data being sent out on the DDS network is in a proprietary mode to allow for remote communications, rate adaption, and SYNC to ASYNC modes ddsNetMode64KClearChannel (DDS-II) A special case of DDS-II, where the line rate is 72K, the data rate is 64K, and there is no secondary channel. ddsNetMode64KCCProprietaryTXPII (DDS-II) A special case of DDS-II, where the line rate is 72K, the data rate is 64K, and there is no secondary channel. In addition, the data being sent out on the DDS network is in a proprietary mode to allow for remote communications, rate adaption, SYNC to ASYNC, and/or TDM modes.
1.3.6.1.4.1.321.100.2.4.1.1.6INTEGER {ddsNetModeNormal(1), ddsNetModeProprietaryTXPI(2), ddsNetMode64KClearChannel(3), ddsNetMode64KCCProprietaryTXPII(4)}read-writecurrent
ddsNetTimingSource
OBJECT-TYPE
This variable describes the current timing source for the DDS network interface. The values mean: ddsNetTimingNet unit dependant upon network for DDS network interface timing ddsNetTimingInt unit supplying timing for DDS network interface ddsNetTimingDTE unit dependant upon DTE device for network interface timing ddsNetTimingPort1 unit dependant upon serial port 1 device for network interface timing ddsNetTimingPort2 unit dependant upon serial port 2 device for network interface timing
1.3.6.1.4.1.321.100.2.4.1.1.7INTEGER {ddsNetTimingNet(1), ddsNetTimingInt(2), ddsNetTimingDTE(3), ddsNetTimingPort1(4), ddsNetTimingPort2(5)}read-writecurrent
ddsNetRemComm
OBJECT-TYPE
This variable describes the current setting for the remote communications link. The values mean: ddsNetRemCommEnabled remote communications can be carried out end to end ddsNetRemCommDisabled remote communications are not allowed ddsNetRemCommNotAvailable this unit does not support remote communications
1.3.6.1.4.1.321.100.2.4.1.1.8INTEGER {ddsNetRemCommEnabled(1), ddsNetRemCommDisabled(2), ddsNetRemCommNotAvailable(3)}read-onlycurrent
ddsNetCircuitAssur
OBJECT-TYPE
This variable describes the current setting for the circuit assurance option. The values mean: ddsNetCircuitAssurEnabled Circuit Assurance is enabled and the integrity of the DDS loop will be maintained ddsNetCircuitAssurDisabled Circuit Assurance is disabled ddsNetCircuitAssurNotAvailable this unit does not support Circuit Assurance
1.3.6.1.4.1.321.100.2.4.1.1.9INTEGER {ddsNetCircuitAssurEnabled(1), ddsNetCircuitAssurDisabled(2), ddsNetCircuitAssurNotAvailable(3)}read-writecurrent
ddsNetAntiStrTimer
OBJECT-TYPE
This variable describes the current setting for the anti streaming timer. The values mean: ddsNetAntiStrTimerOff the AntiStreaming Timer is off ddsNetAntiStrTimer10 the AntiStreaming Timer is set to 10 seconds ddsNetAntiStrTimer30 the AntiStreaming Timer is set to 30 seconds ddsNetAntiStrTimer60 the AntiStreaming Timer is set to 60 seconds
1.3.6.1.4.1.321.100.2.4.1.1.10INTEGER {ddsNetAntiStrTimerOff(1), ddsNetAntiStrTimer10(2), ddsNetAntiStrTimer30(3), ddsNetAntiStrTimer60(4)}read-writecurrent
ddsNetAlarmTable
OBJECT-TYPE
The dds Network Interface Alarm Table.
1.3.6.1.4.1.321.100.2.4.2not-accessiblecurrent
ddsNetAlarmTableEntry
OBJECT-TYPE
An entry in the ddsNetAlarmTable.
1.3.6.1.4.1.321.100.2.4.2.1not-accessiblecurrent
ddsNetAlarmNearIndex
OBJECT-TYPE
Selects the near device.
1.3.6.1.4.1.321.100.2.4.2.1.1INTEGERread-onlycurrent
ddsNetAlarmFarIndex
OBJECT-TYPE
Selects the far device.
1.3.6.1.4.1.321.100.2.4.2.1.2INTEGERread-onlycurrent
ddsNetAlarmIndex
OBJECT-TYPE
Index into the ddsNetAlarmTable.
1.3.6.1.4.1.321.100.2.4.2.1.3INTEGERread-onlycurrent
ddsNetStatusSummary
OBJECT-TYPE
This object provides a summary of the port status.
1.3.6.1.4.1.321.100.2.4.2.1.4DisplayString (SIZE(0..80))read-onlycurrent
ddsNetAlarmSummary
OBJECT-TYPE
This object provides a summary of the port alarms.
1.3.6.1.4.1.321.100.2.4.2.1.5DisplayString (SIZE(0..80))read-onlycurrent
ddsNetLOSStatus
OBJECT-TYPE
Reports if a Loss of Signal condition exists.
1.3.6.1.4.1.321.100.2.4.2.1.6INTEGER {ddsNetStatusLOSOther(1), ddsNetStatusNoLOS(2), ddsNetStatusLOS(3)}read-onlycurrent
ddsNetLOSCount
OBJECT-TYPE
This count contains the number of consecutive seconds the unit received signal has been interrupted.
1.3.6.1.4.1.321.100.2.4.2.1.7INTEGERread-onlycurrent
ddsNetLOSThreshold
OBJECT-TYPE
A period, measured in seconds, in which the DDS received signal is interrupted.
1.3.6.1.4.1.321.100.2.4.2.1.8INTEGER {ddsNetLOSThresholdOther(1), ddsNetLOSThresholdNone(2), ddsNetLOSThreshold1(3), ddsNetLOSThreshold2(4), ddsNetLOSThreshold3(5), ddsNetLOSThreshold4(6), ddsNetLOSThreshold5(7), ddsNetLOSThreshold10(8), ddsNetLOSThreshold20(9), ddsNetLOSThreshold30(10)}read-writecurrent
ddsNetLOSAlarm
OBJECT-TYPE
This status indicates if the Loss of Signal Seconds threshold is exceeded.
1.3.6.1.4.1.321.100.2.4.2.1.9INTEGER {ddsNetLOSAlarmOther(1), ddsNetLOSAlarmNone(2), ddsNetLOSAlarmThresholdExceeded(3)}read-onlycurrent
ddsNetOOFStatus
OBJECT-TYPE
Reports if an Out of Frame condition exists.
1.3.6.1.4.1.321.100.2.4.2.1.10INTEGER {ddsNetStatusOOFOther(1), ddsNetStatusNoOOF(2), ddsNetStatusOOF(3)}read-onlycurrent
ddsNetOOFCount
OBJECT-TYPE
This count contains the number of consecutive seconds the unit has received the out of frame code.
1.3.6.1.4.1.321.100.2.4.2.1.11INTEGERread-onlycurrent
ddsNetOOFThreshold
OBJECT-TYPE
A period, measured in seconds, in which the Out Of Frame code is received or a frame sync loss occurred.
1.3.6.1.4.1.321.100.2.4.2.1.12INTEGER {ddsNetOOFThresholdOther(1), ddsNetOOFThresholdNone(2), ddsNetOOFThreshold1(3), ddsNetOOFThreshold2(4), ddsNetOOFThreshold3(5), ddsNetOOFThreshold4(6), ddsNetOOFThreshold5(7), ddsNetOOFThreshold10(8), ddsNetOOFThreshold20(9), ddsNetOOFThreshold30(10)}read-writecurrent
ddsNetOOFAlarm
OBJECT-TYPE
This status indicates if the Out of Frame Seconds threshold is exceeded.
1.3.6.1.4.1.321.100.2.4.2.1.13INTEGER {ddsNetOOFSAlarmOther(1), ddsNetOOFSAlarmNone(2), ddsNetOOFSAlarmThresholdExceeded(3)}read-onlycurrent
ddsNetOOSStatus
OBJECT-TYPE
Reports if Out of Service codes are received.
1.3.6.1.4.1.321.100.2.4.2.1.14INTEGER {ddsNetStatusOOSOther(1), ddsNetStatusNoOOS(2), ddsNetStatusOOS(3)}read-onlycurrent
ddsNetOOSCount
OBJECT-TYPE
This count contains the number of consecutive seconds the unit has received the out of service code.
1.3.6.1.4.1.321.100.2.4.2.1.15INTEGERread-onlycurrent
ddsNetOOSThreshold
OBJECT-TYPE
A period, measured in seconds, in which the Out Of Service code is received.
1.3.6.1.4.1.321.100.2.4.2.1.16INTEGER {ddsNetOOSThresholdOther(1), ddsNetOOSThresholdNone(2), ddsNetOOSThreshold1(3), ddsNetOOSThreshold2(4), ddsNetOOSThreshold3(5), ddsNetOOSThreshold4(6), ddsNetOOSThreshold5(7), ddsNetOOSThreshold10(8), ddsNetOOSThreshold20(9), ddsNetOOSThreshold30(10)}read-writecurrent
ddsNetOOSAlarm
OBJECT-TYPE
This status indicates if the Out of Service Seconds threshold is exceeded.
1.3.6.1.4.1.321.100.2.4.2.1.17INTEGER {ddsNetOOSAlarmOther(1), ddsNetOOSAlarmNone(2), ddsNetOOSAlarmThresholdExceeded(3)}read-onlycurrent
ddsNetFDLStatus
OBJECT-TYPE
Reports if Facility Data Link errors have occurred.
1.3.6.1.4.1.321.100.2.4.2.1.18INTEGER {ddsNetStatusFDLOther(1), ddsNetStatusNoFDL(2), ddsNetStatusFDL(3)}read-onlycurrent
ddsNetFDLCount
OBJECT-TYPE
This count contains the number of consecutive seconds in which FDL errors have occurred.
1.3.6.1.4.1.321.100.2.4.2.1.19INTEGERread-onlycurrent
ddsNetFDLThreshold
OBJECT-TYPE
A period, measured in seconds, in which FDL errors have occurred.
1.3.6.1.4.1.321.100.2.4.2.1.20INTEGER {ddsNetFDLThresholdOther(1), ddsNetFDLThresholdNone(2), ddsNetFDLThreshold1(3), ddsNetFDLThreshold2(4), ddsNetFDLThreshold3(5), ddsNetFDLThreshold4(6), ddsNetFDLThreshold5(7), ddsNetFDLThreshold10(8), ddsNetFDLThreshold20(9), ddsNetFDLThreshold30(10)}read-writecurrent
ddsNetFDLAlarm
OBJECT-TYPE
This status indicates if the Facility Data Link threshold is exceeded.
1.3.6.1.4.1.321.100.2.4.2.1.21INTEGER {ddsNetFDLAlarmOther(1), ddsNetFDLAlarmNone(2), ddsNetFDLAlarmThresholdExceeded(3)}read-onlycurrent
ddsNetAlarmResetTimer
OBJECT-TYPE
Sets the Alarm Reset Timer, this field can be set to any value in the range 0 to 900.
1.3.6.1.4.1.321.100.2.4.2.1.22INTEGERread-writecurrent
ddsNetAlarmReset
OBJECT-TYPE
This is used to clear the current alarm counts.
1.3.6.1.4.1.321.100.2.4.2.1.23INTEGER {ddsNetAlarmResetOther(1), ddsNetAlarmResetClearAlarms(2)}read-writecurrent
ddsNetBPVStatus
OBJECT-TYPE
Reports if a Bipolar violation event occurred in the last second.
1.3.6.1.4.1.321.100.2.4.2.1.24INTEGER {ddsNetStatusBPVOther(1), ddsNetStatusNoBPV(2), ddsNetStatusBPV(3)}read-onlycurrent
ddsNetBPVCount
OBJECT-TYPE
This count contains the number of consecutive seconds the unit received bipolar violations.
1.3.6.1.4.1.321.100.2.4.2.1.25INTEGERread-onlycurrent
ddsNetBPVThreshold
OBJECT-TYPE
A period, measured in seconds, in which the unit receives bipolar violations before an alarm is triggered.
1.3.6.1.4.1.321.100.2.4.2.1.26INTEGER {ddsNetBPVThresholdOther(1), ddsNetBPVThresholdNone(2), ddsNetBPVThreshold1(3), ddsNetBPVThreshold2(4), ddsNetBPVThreshold3(5), ddsNetBPVThreshold4(6), ddsNetBPVThreshold5(7), ddsNetBPVThreshold10(8), ddsNetBPVThreshold20(9), ddsNetBPVThreshold30(10)}read-writecurrent
ddsNetBPVAlarm
OBJECT-TYPE
This status indicates if the Bipolar violation Seconds threshold is exceeded.
1.3.6.1.4.1.321.100.2.4.2.1.27INTEGER {ddsNetBPVAlarmOther(1), ddsNetBPVAlarmNone(2), ddsNetBPVAlarmThresholdExceeded(3)}read-onlycurrent
serialDte
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.2.5
serialDteConfigTable
OBJECT-TYPE
The Serial DTE Config Table.
1.3.6.1.4.1.321.100.2.5.1not-accessiblecurrent
serialDteConfigTableEntry
OBJECT-TYPE
An entry in the serial DTE Config Table.
1.3.6.1.4.1.321.100.2.5.1.1not-accessiblecurrent
serialDteConfigNearIndex
OBJECT-TYPE
Selects the near device.
1.3.6.1.4.1.321.100.2.5.1.1.1INTEGERread-onlycurrent
serialDteConfigFarIndex
OBJECT-TYPE
Selects the far device.
1.3.6.1.4.1.321.100.2.5.1.1.2INTEGERread-onlycurrent
serialDteConfigIndex
OBJECT-TYPE
Index into the DteTable.
1.3.6.1.4.1.321.100.2.5.1.1.3INTEGERread-onlycurrent
serialDteDescription
OBJECT-TYPE
Contains a textual description of the port.
1.3.6.1.4.1.321.100.2.5.1.1.4DisplayString (SIZE(0..40))read-onlycurrent
serialDteType
OBJECT-TYPE
Selects the DTE port type if applicable.
1.3.6.1.4.1.321.100.2.5.1.1.5INTEGER {serialDteTypeOther(1), serialDteTypeV35(2), serialDteTypeRS232(3), serialDteTypeEIA530(4), serialDteTypeX21(5), serialDteTypeV36(6), serialDteTypeEIA530A(7)}read-writecurrent
serialDteRate
OBJECT-TYPE
Selects the DTE port bit.
1.3.6.1.4.1.321.100.2.5.1.1.6INTEGER {serialDteRateOther(1), serialDteRate2400(2), serialDteRate4800(3), serialDteRate9600(4), serialDteRate19200(5), serialDteRate38400(6), serialDteRate52000(7), serialDteRate56000(8), serialDteRate57600(9), serialDteRate60000(10), serialDteRate64000(11), serialDteRate112000(12), serialDteRate128000(13), serialDteRate168000(14), serialDteRate192000(15), serialDteRate224000(16), serialDteRate256000(17), serialDteRate280000(18), serialDteRate320000(19), serialDteRate336000(20), serialDteRate384000(21), serialDteRate392000(22), serialDteRate448000(23), serialDteRate504000(24), serialDteRate512000(25), serialDteRate560000(26), serialDteRate576000(27), serialDteRate616000(28), serialDteRate640000(29), serialDteRate672000(30), serialDteRate704000(31), serialDteRate728000(32), serialDteRate768000(33), serialDteRate784000(34), serialDteRate832000(35), serialDteRate840000(36), serialDteRate896000(37), serialDteRate952000(38), serialDteRate960000(39), serialDteRate1008000(40), serialDteRate1024000(41), serialDteRate1064000(42), serialDteRate1088000(43), serialDteRate1120000(44), serialDteRate1152000(45), serialDteRate1176000(46), serialDteRate1216000(47), serialDteRate1232000(48), serialDteRate1280000(49), serialDteRate1288000(50), serialDteRate1344000(51), serialDteRate1400000(52), serialDteRate1408000(53), serialDteRate1456000(54), serialDteRate1472000(55), serialDteRate1512000(56), serialDteRate1536000(57), serialDteRate1568000(58), serialDteRate1600000(59), serialDteRate1624000(60), serialDteRate1664000(61), serialDteRate1680000(62), serialDteRate1728000(63), serialDteRate1736000(64), serialDteRate1792000(65), serialDteRate1856000(66), serialDteRate1920000(67), serialDteRate1984000(68), serialDteRate2048000(69), serialDteRate1200(70), serialDteRate14400(71), serialDteRate28800(72), serialDteRate48000(73), serialDteRate31200(74), serialDteRate115200(75), serialDteRate2112000(76), serialDteRate2176000(77), serialDteRate2240000(78), serialDteRate2304000(79), serialDteRate300(80), serialDteRate600(81), serialDteRate3072000(82), serialDteRate4096000(83)}read-writecurrent
serialDteInvertData
OBJECT-TYPE
Specifies whether transmit and receive are inverted at the port.
1.3.6.1.4.1.321.100.2.5.1.1.7INTEGER {serialDteInvertDataOther(1), serialDteInvertDataDisabled(2), serialDteInvertDataEnabled(3)}read-writecurrent
serialDteFormat
OBJECT-TYPE
This variable describes the current operations format of the DTE interface. The values mean: serialDteFormatSync The DTE interface is currently set to operate in Synchronous clocking format serialDteFormatAsync The DTE interface is currently set to operate in the Asynchronous clocking format serialDteFormatNotAvail The DTE interface operating format is not available
1.3.6.1.4.1.321.100.2.5.1.1.8INTEGER {serialDteFormatOther(1), serialDteFormatSync(2), serialDteFormatAsync(3), serialDteFormatNotAvail(4)}read-writecurrent
serialDteParity
OBJECT-TYPE
This variable describes the current parity selected for the DTE interface. This variable is only valid when the DTE Mode is set to ASYNC. The values mean: serialDteParityNone The DTE interface is currently set for no parity bit checking or generation serialDteParityOdd The DTE interface is currently set for odd parity serialDteParityEven The DTE interface is currently set for even parity serialDteParityMark The DTE interface is currently set for mark parity serialDteParitySpace The DTE interface is currently set for space parity serialDteParityNotAvail The parity setting on the DTE interface is not available.
1.3.6.1.4.1.321.100.2.5.1.1.9INTEGER {serialDteParityOther(1), serialDteParityNone(2), serialDteParityOdd(3), serialDteParityEven(4), serialDteParityMark(5), serialDteParitySpace(6), serialDteParityNotAvail(7)}read-writecurrent
serialDteStopBit
OBJECT-TYPE
This variable describes the stop bit setting for the DTE interface. This variable is only valid when the DTE interface is set to ASYNC. The values mean: serialDteStopBit1 The DTE interface is configured to operate in the ASYNC mode with 1 stop bit serialDteStopBit2 The DTE interface is configured to operate in the ASYNC mode with 2 stop bits serialDteStopBitNotAvail The stop bit information is not available. The DTE interface is probably configured for synchronous operation.
1.3.6.1.4.1.321.100.2.5.1.1.10INTEGER {serialDteStopBitOther(1), serialDteStopBit1(2), serialDteStopBit2(3), serialDteStopBitNotAvail(4)}read-writecurrent
serialDteMode
OBJECT-TYPE
This variable describes mode in which data is being sent from the DDS unit back towards the network.
1.3.6.1.4.1.321.100.2.5.1.1.11INTEGER {serialDteModeOther(1), serialDteModeDDSI(2), serialDteModeDDSII(3), serialDteModeTxpINormal(4), serialDteModeTxpITDM(5), serialDteModeTxpIINormal(6), serialDteModeTxpIITDM(7)}read-writecurrent
serialDteDSR
OBJECT-TYPE
Selects DSR behavior.
1.3.6.1.4.1.321.100.2.5.1.1.12INTEGER {serialDteDSROther(1), serialDteDSRTestOff(2), serialDteDSRForcedOn(3), serialDteDSRForcedOff(4), serialDteDSRInternal(5)}read-writecurrent
serialDteDCD
OBJECT-TYPE
Selects DCD behavior.
1.3.6.1.4.1.321.100.2.5.1.1.13INTEGER {serialDteDCDOther(1), serialDteDCDIdleOff(2), serialDteDCDForcedOn(3), serialDteDCDForcedOff(4), serialDteDCDInternal(5), serialDteDCDFarRTS(6)}read-writecurrent
serialDteRTS
OBJECT-TYPE
Selects RTS behavior.
1.3.6.1.4.1.321.100.2.5.1.1.14INTEGER {serialDteRTSOther(1), serialDteRTSNormal(2), serialDteRTSForcedOn(3), serialDteRTSExternal(4)}read-writecurrent
serialDteRTSDelay
OBJECT-TYPE
Selects RTS to CTS transition delay.
1.3.6.1.4.1.321.100.2.5.1.1.15INTEGER {serialDteRTSDelayOther(1), serialDteRTSDelayNormal(2), serialDteRTSDelayLong(3)}read-writecurrent
serialDteDTR
OBJECT-TYPE
Reports if DTR from the DTE device is false.
1.3.6.1.4.1.321.100.2.5.1.1.16INTEGER {serialDteDTROther(1), serialDteDTRFalse(2), serialDteDTRTrue(3)}read-onlycurrent
serialDteCTS
OBJECT-TYPE
Specifies the control of the CTS signal at the port.
1.3.6.1.4.1.321.100.2.5.1.1.17INTEGER {serialDteCTSOther(1), serialDteCTSForceTrue(2), serialDteCTSForceFalse(3), serialDteCTSInternal(4)}read-writecurrent
serialDteV54
OBJECT-TYPE
Specifies if the unit should respond to inband V.54 loop commands.
1.3.6.1.4.1.321.100.2.5.1.1.18INTEGER {serialDteV54Other(1), serialDteV54Disable(2), serialDteV54Enable(3)}read-writecurrent
serialDteLL
OBJECT-TYPE
Specifies if the unit should respond to local loop activation by the local loopback signal (EIA530 or RS-232 pin 18).
1.3.6.1.4.1.321.100.2.5.1.1.19INTEGER {serialDteLLOther(1), serialDteLLDisable(2), serialDteLLEnable(3)}read-writecurrent
serialDteRL
OBJECT-TYPE
Specifies if the unit should respond to remote loop activation by the remote loopback signal (EIA530 or RS-232 pin 21).
1.3.6.1.4.1.321.100.2.5.1.1.20INTEGER {serialDteRLOther(1), serialDteRLDisable(2), serialDteRLEnable(3)}read-writecurrent
serialDteStartChannel
OBJECT-TYPE
Specifies the starting channel for the interface.
1.3.6.1.4.1.321.100.2.5.1.1.21INTEGERread-writecurrent
serialDteNumberOfChannels
OBJECT-TYPE
Specifies the number of channels allocated to the interface.
1.3.6.1.4.1.321.100.2.5.1.1.22INTEGERread-writecurrent
serialDteTxClock
OBJECT-TYPE
Specifies how the interface derives its transmit clock.
1.3.6.1.4.1.321.100.2.5.1.1.23INTEGER {serialDteTxClockOther(1), serialDteTxClockInternal(2), serialDteTxClockExternal(3), serialDteTxClockOversample(4)}read-writecurrent
serialDteBundle
OBJECT-TYPE
Specifies the allocation pattern of channels assigned to the serial port.
1.3.6.1.4.1.321.100.2.5.1.1.24INTEGER {other(1), contiguous(2), alternate(3)}read-writecurrent
serialDteChannelRate
OBJECT-TYPE
Specifies the rate of all channels assigned to the serial port.
1.3.6.1.4.1.321.100.2.5.1.1.25INTEGER {other(1), nx56k(2), nx64k(3)}read-writecurrent
serialDteInvertClock
OBJECT-TYPE
Specifies if an inverted clock is used to send data from the serial port.
1.3.6.1.4.1.321.100.2.5.1.1.26INTEGER {other(1), disabled(2), enabled(3)}read-writecurrent
serialDteCharSize
OBJECT-TYPE
Specifies the number of bits per character. This variable is valid in ASYNC mode.
1.3.6.1.4.1.321.100.2.5.1.1.27INTEGER {other(1), five(2), six(3), seven(4), eight(5)}read-writecurrent
serialDteFlowControl
OBJECT-TYPE
Specifies the Flow control to use. This variable is valid only in ASYNC mode.
1.3.6.1.4.1.321.100.2.5.1.1.28INTEGER {other(1), none(2), xonXoff(3), rtsCts(4)}read-writecurrent
serialDtePinStatus
OBJECT-TYPE
This object provides a summary of the Serial port pin status.
1.3.6.1.4.1.321.100.2.5.1.1.29DisplayString (SIZE(0..80))read-onlycurrent
serialDteInInvertClock
OBJECT-TYPE
Specifies to use the inverted clock edge for data clocked into the serial port.
1.3.6.1.4.1.321.100.2.5.1.1.30INTEGER {other(1), disabled(2), enabled(3)}read-writecurrent
serialDteAlarmTable
OBJECT-TYPE
The Serial DTE Alarm Table.
1.3.6.1.4.1.321.100.2.5.2not-accessiblecurrent
serialDteAlarmTableEntry
OBJECT-TYPE
An entry in the serial DTE Alarm Table.
1.3.6.1.4.1.321.100.2.5.2.1not-accessiblecurrent
serialDteAlarmNearIndex
OBJECT-TYPE
Selects the near device.
1.3.6.1.4.1.321.100.2.5.2.1.1INTEGERread-onlycurrent
serialDteAlarmFarIndex
OBJECT-TYPE
Selects the far device.
1.3.6.1.4.1.321.100.2.5.2.1.2INTEGERread-onlycurrent
serialDteAlarmIndex
OBJECT-TYPE
Index into the serialDteAlarmTable.
1.3.6.1.4.1.321.100.2.5.2.1.3INTEGERread-onlycurrent
serialDteDTRAlarmControl
OBJECT-TYPE
Specifies if the unit should alarm on loss of DTR.
1.3.6.1.4.1.321.100.2.5.2.1.4INTEGER {serialDteDTRAlarmOther(1), serialDteDTRAlarmDisable(2), serialDteDTRAlarmEnable(3)}read-writecurrent
serialDteDTRAlarmStatus
OBJECT-TYPE
This status indicates a DTR Loss alarm is active.
1.3.6.1.4.1.321.100.2.5.2.1.5INTEGER {serialDteDTRAlarmOther(1), serialDteDTRAlarmNone(2), serialDteDTRAlarmActive(3)}read-onlycurrent
serialDteStatusSummary
OBJECT-TYPE
This object provides a summary of the port status.
1.3.6.1.4.1.321.100.2.5.2.1.6DisplayString (SIZE(0..80))read-onlycurrent
serialDteAlarmSummary
OBJECT-TYPE
This object provides a summary of the port alarms.
1.3.6.1.4.1.321.100.2.5.2.1.7DisplayString (SIZE(0..80))read-onlycurrent
serialDteASCStatus
OBJECT-TYPE
Reports if an ASC condition exists on the interface.
1.3.6.1.4.1.321.100.2.5.2.1.8INTEGER {serialDteStatusASCOther(1), serialDteStatusNoASC(2), serialDteStatusASC(3)}read-onlycurrent
serialDteASCCount
OBJECT-TYPE
This count contains the number of ASC seconds received by the interface.
1.3.6.1.4.1.321.100.2.5.2.1.9INTEGERread-onlycurrent
serialDteASCThreshold
OBJECT-TYPE
The number of ASC seconds that must be received before an alarm is declared.
1.3.6.1.4.1.321.100.2.5.2.1.10INTEGERread-writecurrent
serialDteASCAlarm
OBJECT-TYPE
This status indicates if the ASC Seconds threshold is exceeded.
1.3.6.1.4.1.321.100.2.5.2.1.11INTEGER {serialDteASCAlarmOther(1), serialDteASCAlarmNone(2), serialDteASCAlarmThresholdExceeded(3)}read-onlycurrent
serialDteFDLStatus
OBJECT-TYPE
Reports if an FDL error condition exists on the interface.
1.3.6.1.4.1.321.100.2.5.2.1.12INTEGER {serialDteStatusFDLOther(1), serialDteStatusNoFDL(2), serialDteStatusFDL(3)}read-onlycurrent
serialDteFDLCount
OBJECT-TYPE
This count contains the number of FDL errored seconds received by the interface.
1.3.6.1.4.1.321.100.2.5.2.1.13INTEGERread-onlycurrent
serialDteFDLThreshold
OBJECT-TYPE
The number of FDL errored seconds that must be received before an alarm is declared.
1.3.6.1.4.1.321.100.2.5.2.1.14INTEGERread-writecurrent
serialDteFDLAlarm
OBJECT-TYPE
This status indicates if the FDL Errored Seconds threshold is exceeded.
1.3.6.1.4.1.321.100.2.5.2.1.15INTEGER {serialDteFDLAlarmOther(1), serialDteFDLAlarmNone(2), serialDteFDLAlarmThresholdExceeded(3)}read-onlycurrent
serialDteLOSStatus
OBJECT-TYPE
Reports if an LOS condition exists on the interface.
1.3.6.1.4.1.321.100.2.5.2.1.16INTEGER {serialDteStatusLOSOther(1), serialDteStatusNoLOS(2), serialDteStatusLOS(3)}read-onlycurrent
serialDteLOSCount
OBJECT-TYPE
This count contains the number of LOS seconds received by the interface.
1.3.6.1.4.1.321.100.2.5.2.1.17INTEGERread-onlycurrent
serialDteLOSThreshold
OBJECT-TYPE
The number of LOS seconds that must be received before an alarm is declared.
1.3.6.1.4.1.321.100.2.5.2.1.18INTEGERread-writecurrent
serialDteLOSAlarm
OBJECT-TYPE
This status indicates if the LOS Seconds threshold is exceeded.
1.3.6.1.4.1.321.100.2.5.2.1.19INTEGER {serialDteLOSAlarmOther(1), serialDteLOSAlarmNone(2), serialDteLOSAlarmThresholdExceeded(3)}read-onlycurrent
analogDte
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.2.6
analogDteTable
OBJECT-TYPE
The Analog DTE Table.
1.3.6.1.4.1.321.100.2.6.1not-accessiblecurrent
analogDteTableEntry
OBJECT-TYPE
An entry in the Analog DTE Table.
1.3.6.1.4.1.321.100.2.6.1.1not-accessiblecurrent
analogDteNearIndex
OBJECT-TYPE
Selects the near device.
1.3.6.1.4.1.321.100.2.6.1.1.1INTEGERread-onlycurrent
analogDteFarIndex
OBJECT-TYPE
Selects the far device.
1.3.6.1.4.1.321.100.2.6.1.1.2INTEGERread-onlycurrent
analogDteIndex
OBJECT-TYPE
Index into the analogDteTable.
1.3.6.1.4.1.321.100.2.6.1.1.3INTEGERread-onlycurrent
analogDteDescription
OBJECT-TYPE
Contains a textual description of the port.
1.3.6.1.4.1.321.100.2.6.1.1.4DisplayString (SIZE(0..40))read-onlycurrent
analogDteCardType
OBJECT-TYPE
Identifies the analog DTE card type.
1.3.6.1.4.1.321.100.2.6.1.1.5INTEGER {analogDteCardTypeOther(1), analogDteCardTypeFXS(2), analogDteCardTypeFXO(3), analogDteCardType4WEM(4)}read-onlycurrent
analogDteMode
OBJECT-TYPE
Selects whether the port is actively assigned to a network channel or not used.
1.3.6.1.4.1.321.100.2.6.1.1.6INTEGER {analogDteModeOther(1), analogDteModeSpare(2), analogDteModeActive(3)}read-writecurrent
analogDteState
OBJECT-TYPE
Displays the port status as either in the Busy or Idle state.
1.3.6.1.4.1.321.100.2.6.1.1.7INTEGER {analogDteStateOther(1), analogDteStateIdle(2), analogDteStateBusy(3)}read-onlycurrent
analogDteElementID
OBJECT-TYPE
This object signifies the name of the device.
1.3.6.1.4.1.321.100.2.6.1.1.8DisplayString (SIZE(0..20))read-writecurrent
analogDteSignalling
OBJECT-TYPE
Selects the supervisory operation of the port.
1.3.6.1.4.1.321.100.2.6.1.1.9INTEGER {analogDteSignallingOther(1), analogDteSignallingFXSLS(2), analogDteSignallingFXSGS(3), analogDteSignallingUVG(4), analogDteSignallingMEGLS(5), analogDteSignallingMEGGS(6), analogDteSignallingMEGRLS(7), analogDteSignallingMEGRGS(8), analogDteSignallingPLAR(9), analogDteSignallingSLC96(10), analogDteSignallingDIDDNIS(11), analogDteSignallingDNISWLS(12), analogDteSignallingDNISDLS(13), analogDteSignallingDNISWRLS(14), analogDteSignallingDNISDRLS(15), analogDteSignallingDNISWGS(16), analogDteSignallingDNISDGS(17), analogDteSignallingDNISWRGS(18), analogDteSignallingDNISDRGS(19), analogDteSignallingFXOLS(20), analogDteSignallingFXOGS(21), analogDteSignallingFXOUVG(22), analogDteSignallingFXOUVGR(23), analogDteSignalling4WEMTYPE1(24), analogDteSignalling4WEMTYPE2(25), analogDteSignalling4WEMTYPE3(26), analogDteSignalling4WEMTYPE4(27), analogDteSignalling4WEMTYPE5(28), analogDteSignalling4WEMTO(29)}read-writecurrent
analogDteDNISDelay
OBJECT-TYPE
If the signalling mode has a delay, it can be set from 1 to 5 seconds.
1.3.6.1.4.1.321.100.2.6.1.1.10INTEGER {analogDteDNISDelayOther(1), analogDteDNISDelay1Second(2), analogDteDNISDelay2Seconds(3), analogDteDNISDelay3Seconds(4), analogDteDNISDelay4Seconds(5), analogDteDNISDelay5Seconds(6)}read-writecurrent
analogDteTxGain
OBJECT-TYPE
Selects the transmit gain. Values prefixed with m are negative.
1.3.6.1.4.1.321.100.2.6.1.1.11INTEGER {analogDteTxGainOther(1), analogDteTxGain3DB(2), analogDteTxGain2DB(3), analogDteTxGain1DB(4), analogDteTxGain0DB(5), analogDteTxGainm1DB(6), analogDteTxGainm2DB(7), analogDteTxGainm3DB(8), analogDteTxGainm4DB(9), analogDteTxGainm5DB(10), analogDteTxGainm6DB(11), analogDteTxGainm7DB(12), analogDteTxGainm8DB(13), analogDteTxGainm9DB(14), analogDteTxGainm10DB(15)}read-writecurrent
analogDteRxGain
OBJECT-TYPE
Selects the receive gain. Values prefixed with m are negative.
1.3.6.1.4.1.321.100.2.6.1.1.12INTEGER {analogDteRxGainOther(1), analogDteRxGain2DB(2), analogDteRxGain1DB(3), analogDteRxGain0DB(4), analogDteRxGainm1DB(5), analogDteRxGainm2DB(6), analogDteRxGainm3DB(7), analogDteRxGainm4DB(8), analogDteRxGainm5DB(9), analogDteRxGainm6DB(10), analogDteRxGainm7DB(11), analogDteRxGainm8DB(12), analogDteRxGainm9DB(13), analogDteRxGainm10DB(14), analogDteRxGainm11DB(15), analogDteRxGainm12DB(16), analogDteRxGainm13DB(17), analogDteRxGainm14DB(18), analogDteRxGainm15DB(19), analogDteRxGainm16DB(20)}read-writecurrent
connection
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.2.7
connectionTable
OBJECT-TYPE
The connection table.
1.3.6.1.4.1.321.100.2.7.1not-accessiblecurrent
connectionTableEntry
OBJECT-TYPE
An entry in the connection table.
1.3.6.1.4.1.321.100.2.7.1.1not-accessiblecurrent
connectionNearIndex
OBJECT-TYPE
Selects the near device.
1.3.6.1.4.1.321.100.2.7.1.1.1INTEGERread-onlycurrent
connectionFarIndex
OBJECT-TYPE
Selects the far device.
1.3.6.1.4.1.321.100.2.7.1.1.2INTEGERread-onlycurrent
connectionTableIndex
OBJECT-TYPE
The index into the connection table.
1.3.6.1.4.1.321.100.2.7.1.1.3INTEGERread-onlycurrent
connectionTableDescription
OBJECT-TYPE
A description of the connection.
1.3.6.1.4.1.321.100.2.7.1.1.4DisplayString (SIZE(0..60))read-onlycurrent
connectionChannelTable
OBJECT-TYPE
The channel-level connection table.
1.3.6.1.4.1.321.100.2.7.2not-accessiblecurrent
connectionChannelEntry
OBJECT-TYPE
An entry in the connectionChannelTable.
1.3.6.1.4.1.321.100.2.7.2.1not-accessiblecurrent
connectionChannelNearIndex
OBJECT-TYPE
Selects the near device.
1.3.6.1.4.1.321.100.2.7.2.1.1INTEGERread-onlycurrent
connectionChannelFarIndex
OBJECT-TYPE
Selects the far device.
1.3.6.1.4.1.321.100.2.7.2.1.2INTEGERread-onlycurrent
connectionChannelLineIndex
OBJECT-TYPE
Selects instance of line.
1.3.6.1.4.1.321.100.2.7.2.1.3INTEGERread-onlycurrent
connectionChannelIndex
OBJECT-TYPE
The index into the connection table.
1.3.6.1.4.1.321.100.2.7.2.1.4INTEGERread-onlycurrent
channelInterfaceAssignment
OBJECT-TYPE
The channel assignment.
1.3.6.1.4.1.321.100.2.7.2.1.5INTEGER {other(1), unassigned(2), dTE(3), remComm(4), port1(5), port2(6), port3(7), port4(8), port5(9), port6(10), port7(11), port8(12), port9(13), port10(14), port11(15), port12(16), port13(17), port14(18), port15(19), port16(20), port17(21), port18(22), port19(23), port20(24), port21(25), port22(26), port23(27), port24(28), port25(29), port26(30), port27(31), port28(32), port29(33), port30(34), port31(35), port32(36), slot2PortA(37), slot2PortB(38), slot3PortA(39), slot3PortB(40), slot4PortA(41), slot4PortB(42), slot5PortA(43), slot5PortB(44), slot6PortA(45), slot6PortB(46), slot2Dsu1PortA(47), slot2Dsu1PortB(48), slot2Dsu2PortA(49), slot2Dsu2PortB(50), slot2Dsu3PortA(51), slot2Dsu3PortB(52), slot2Dsu4PortA(53), slot2Dsu4PortB(54), slot2Dsu5PortA(55), slot2Dsu5PortB(56), slot2Dsu6PortA(57), slot2Dsu6PortB(58), slot3Dsu1PortA(59), slot3Dsu1PortB(60), slot3Dsu2PortA(61), slot3Dsu2PortB(62), slot3Dsu3PortA(63), slot3Dsu3PortB(64), slot3Dsu4PortA(65), slot3Dsu4PortB(66), slot3Dsu5PortA(67), slot3Dsu5PortB(68), slot3Dsu6PortA(69), slot3Dsu6PortB(70), slot4Dsu1PortA(71), slot4Dsu1PortB(72), slot4Dsu2PortA(73), slot4Dsu2PortB(74), slot4Dsu3PortA(75), slot4Dsu3PortB(76), slot4Dsu4PortA(77), slot4Dsu4PortB(78), slot4Dsu5PortA(79), slot4Dsu5PortB(80), slot4Dsu6PortA(81), slot4Dsu6PortB(82), slot5Dsu1PortA(83), slot5Dsu1PortB(84), slot5Dsu2PortA(85), slot5Dsu2PortB(86), slot5Dsu3PortA(87), slot5Dsu3PortB(88), slot5Dsu4PortA(89), slot5Dsu4PortB(90), slot5Dsu5PortA(91), slot5Dsu5PortB(92), slot5Dsu6PortA(93), slot5Dsu6PortB(94), slot6Dsu1PortA(95), slot6Dsu1PortB(96), slot6Dsu2PortA(97), slot6Dsu2PortB(98), slot6Dsu3PortA(99), slot6Dsu3PortB(100), slot6Dsu4PortA(101), slot6Dsu4PortB(102), slot6Dsu5PortA(103), slot6Dsu5PortB(104), slot6Dsu6PortA(105), slot6Dsu6PortB(106)}read-writecurrent
channelInterfaceDescription
OBJECT-TYPE
Contains a description of the interface channel connection.
1.3.6.1.4.1.321.100.2.7.2.1.6DisplayString (SIZE(0..40))read-onlycurrent
channelInterfaceChannel
OBJECT-TYPE
Displays the corresponding channel of the interface channel connection.
1.3.6.1.4.1.321.100.2.7.2.1.7INTEGERread-writecurrent
channelSignalling
OBJECT-TYPE
Allows a selection of Clear Channel or Robbed Bit signalling for each DS0.
1.3.6.1.4.1.321.100.2.7.2.1.8INTEGER {other(1), clearChannel(2), robbedBit(3)}read-writecurrent
maintenance
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.2.8
bertTable
OBJECT-TYPE
BERT control table.
1.3.6.1.4.1.321.100.2.8.1not-accessiblecurrent
bertTableEntry
OBJECT-TYPE
An entry in the BERT control table.
1.3.6.1.4.1.321.100.2.8.1.1not-accessiblecurrent
bertNearIndex
OBJECT-TYPE
Selects the near device.
1.3.6.1.4.1.321.100.2.8.1.1.1INTEGERread-onlycurrent
bertFarIndex
OBJECT-TYPE
Selects the far device.
1.3.6.1.4.1.321.100.2.8.1.1.2INTEGERread-onlycurrent
bertIndex
OBJECT-TYPE
The index into the BERT control table. Selects which BERT chip to use.
1.3.6.1.4.1.321.100.2.8.1.1.3INTEGERread-onlycurrent
bertPattern
OBJECT-TYPE
Selects the test pattern to be used.
1.3.6.1.4.1.321.100.2.8.1.1.4INTEGER {bertPatternOther(1), bertPatternQRSS(2), bertPattern63(3), bertPattern511(4), bertPattern2047(5), bertPattern215(6), bertPattern220(7), bertPattern223(8), bertPattern1in8(9), bertPattern3in24(10), bertPatternALT(11), bertPatternCLEAR(12)}read-writecurrent
bertLength
OBJECT-TYPE
Specifies how long the test should run.
1.3.6.1.4.1.321.100.2.8.1.1.5INTEGER {bertLengthOther(1), bertLength15minutes(2), bertLength30minutes(3), bertLength60minutes(4), bertLength24hours(5), bertLengthContinuous(6)}read-writecurrent
bertPatternSync
OBJECT-TYPE
Displays the current state of pattern sync during a test.
1.3.6.1.4.1.321.100.2.8.1.1.6INTEGER {bertPatternSyncOther(1), bertPatternSyncNoTest(2), bertPatternSyncNoSync(3), bertPatternSyncInsync(4)}read-onlycurrent
bertElapsedTime
OBJECT-TYPE
Displays the amount of time elapsed since a timed test began in seconds.
1.3.6.1.4.1.321.100.2.8.1.1.7INTEGERread-onlycurrent
bertBitErrors
OBJECT-TYPE
Displays the total number of bit errors detected since the test began.
1.3.6.1.4.1.321.100.2.8.1.1.8INTEGERread-onlycurrent
bertErroredSeconds
OBJECT-TYPE
Displays the number of asynchronous errored seconds that have been detected since the test began.
1.3.6.1.4.1.321.100.2.8.1.1.9INTEGERread-onlycurrent
bertPercentEFS
OBJECT-TYPE
Displays a ratio derived from the number of error free seconds divided by the number of seconds accumulated in elapsed time.
1.3.6.1.4.1.321.100.2.8.1.1.10INTEGERread-onlycurrent
bertCommand
OBJECT-TYPE
Issues a test command for the interface.
1.3.6.1.4.1.321.100.2.8.1.1.11INTEGER {bertCommandOther(1), bertCommandStart(2), bertCommandStop(3), bertCommandResetErrors(4), bertCommandInjectError(5)}read-writecurrent
bertInterfaceTable
OBJECT-TYPE
BERT control interface table.
1.3.6.1.4.1.321.100.2.8.2not-accessiblecurrent
bertInterfaceTableEntry
OBJECT-TYPE
An entry in the BERT control interface table.
1.3.6.1.4.1.321.100.2.8.2.1not-accessiblecurrent
bertInterfaceNearIndex
OBJECT-TYPE
Selects the near device.
1.3.6.1.4.1.321.100.2.8.2.1.1INTEGERread-onlycurrent
bertInterfaceFarIndex
OBJECT-TYPE
Selects the far device.
1.3.6.1.4.1.321.100.2.8.2.1.2INTEGERread-onlycurrent
bertChipIndex
OBJECT-TYPE
Selects which BERT chip to use.
1.3.6.1.4.1.321.100.2.8.2.1.3INTEGERread-onlycurrent
bertInterfaceIndex
OBJECT-TYPE
An index into the MIB-II interfaces table; the interface for the BERT settings.
1.3.6.1.4.1.321.100.2.8.2.1.4INTEGERread-onlycurrent
bertInterfaceSetting
OBJECT-TYPE
Specifies where to send the BERT pattern.
1.3.6.1.4.1.321.100.2.8.2.1.5INTEGER {bertInterfaceSettingOther(1), bertInterfaceSettingIdle(2), bertInterfaceSettingChannel1(3), bertInterfaceSettingChannel2(4), bertInterfaceSettingChannel3(5), bertInterfaceSettingChannel4(6), bertInterfaceSettingChannel5(7), bertInterfaceSettingChannel6(8), bertInterfaceSettingChannel7(9), bertInterfaceSettingChannel8(10), bertInterfaceSettingChannel9(11), bertInterfaceSettingChannel10(12), bertInterfaceSettingChannel11(13), bertInterfaceSettingChannel12(14), bertInterfaceSettingChannel13(15), bertInterfaceSettingChannel14(16), bertInterfaceSettingChannel15(17), bertInterfaceSettingChannel16(18), bertInterfaceSettingChannel17(19), bertInterfaceSettingChannel18(20), bertInterfaceSettingChannel19(21), bertInterfaceSettingChannel20(22), bertInterfaceSettingChannel21(23), bertInterfaceSettingChannel22(24), bertInterfaceSettingChannel23(25), bertInterfaceSettingChannel24(26), bertInterfaceSettingChannel25(27), bertInterfaceSettingChannel26(28), bertInterfaceSettingChannel27(29), bertInterfaceSettingChannel28(30), bertInterfaceSettingChannel29(31), bertInterfaceSettingChannel30(32), bertInterfaceSettingChannel31(33), bertInterfaceSettingChannel32(34), bertInterfaceSettingNet(35), bertInterfaceSettingDTE(36), bertInterfaceSettingNotEnabled(37), bertInterfaceSettingUseService(38)}read-writecurrent
bertInterfaceService
OBJECT-TYPE
Specifies the service (see ipadv2.mib) to BERT. The bandwidth associated with the service will get the BERT pattern.
1.3.6.1.4.1.321.100.2.8.2.1.6INTEGERread-writecurrent
bertInterfaceChannelRate
OBJECT-TYPE
Specifies the network channel rate for all channels involved in a network BERT.
1.3.6.1.4.1.321.100.2.8.2.1.7INTEGER {other(1), nx56k(2), nx64k(3)}read-writecurrent
testTable
OBJECT-TYPE
Test control table.
1.3.6.1.4.1.321.100.2.8.3not-accessiblecurrent
testTableEntry
OBJECT-TYPE
An entry in the testTable.
1.3.6.1.4.1.321.100.2.8.3.1not-accessiblecurrent
testNearIndex
OBJECT-TYPE
Selects the near device.
1.3.6.1.4.1.321.100.2.8.3.1.1INTEGERread-onlycurrent
testFarIndex
OBJECT-TYPE
Selects the far device.
1.3.6.1.4.1.321.100.2.8.3.1.2INTEGERread-onlycurrent
testTableIndex
OBJECT-TYPE
The index into the testTable, one entry for each interface.
1.3.6.1.4.1.321.100.2.8.3.1.3INTEGERread-onlycurrent
testType
OBJECT-TYPE
Identifies the test type for the interface.
1.3.6.1.4.1.321.100.2.8.3.1.4INTEGER {testTypeOther(1), testTypeNoTest(2), testTypePLB(3), testTypeLLB(4), testtypeMLB(5), testTypeFarPLB(6), testTypeFarLLB(7), testTypeFarMLB(8), testTypePortLoop(9), testTypeV54Loop(10), testTypeFarV54Loop(11), testTypeFarPortLoop(12), testTypeTDM(13), testTypeFarPortUnloop(14), testTypeFarV54Unloop(15), testTypeDualLoop(16), testTypeNetworkSideTransparent(17), testTypeNetworkSideNonTransparent(18), testTypeCustomerSideTransparent(19), testTypeCustomerSideNonTransparent(20)}read-writecurrent
testLoopDirection
OBJECT-TYPE
This object is the identifier of the current unit loop mode. The values mean: testLoopUnidirectional Line, Data, and V54 loops will be unidirectional Local loop will be bidirectional testLoopBidirectional All loops will be bidirectional
1.3.6.1.4.1.321.100.2.8.3.1.5INTEGER {testLoopOther(1), testLoopUnidirectional(2), testLoopBidirectional(3)}read-writecurrent
testFarLLBFraming
OBJECT-TYPE
This setting, for Far LLB tests on T1 lines, must match the far end unit loop code framing.
1.3.6.1.4.1.321.100.2.8.3.1.6INTEGER {testFarLLBFramingOther(1), testFarLLBFramingUnframed(2), testFarLLBFramingFramed(3)}read-writecurrent
testLoopInitiator
OBJECT-TYPE
Indicates who started the loop.
1.3.6.1.4.1.321.100.2.8.3.1.7INTEGER {testLoopInitiatorOther(1), testLoopInitiatorLMP(2), testLoopInitiatorSNMP(3), testLoopInitiatorWeb(4), testLoopInitiatorEOC(5), testLoopInitiatorButtons(6), testLoopInitiatorDCEControl(7), testLoopInitiatorISDNPRAV3(8)}read-onlycurrent
testDefaultLoopType
OBJECT-TYPE
Identifies the default loop type.
1.3.6.1.4.1.321.100.2.8.3.1.8INTEGER {testDefaultLoopTypeOther(1), testDefaultLoopTypeTransparent(2), testDefaultLoopTypeNonTransparent(3), testDefaultLoopTypeDual(4)}read-writecurrent
performance
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.2.9
performance24Table
OBJECT-TYPE
Performance table, contains TR54016 standard and enhanced data.
1.3.6.1.4.1.321.100.2.9.1not-accessiblecurrent
performance24TableEntry
OBJECT-TYPE
An entry in the performance24Table.
1.3.6.1.4.1.321.100.2.9.1.1not-accessiblecurrent
performance24NearIndex
OBJECT-TYPE
Selects the near device.
1.3.6.1.4.1.321.100.2.9.1.1.1INTEGERread-onlycurrent
performance24FarIndex
OBJECT-TYPE
Selects the far device.
1.3.6.1.4.1.321.100.2.9.1.1.2INTEGERread-onlycurrent
performance24InterfaceIndex
OBJECT-TYPE
Selects the interface.
1.3.6.1.4.1.321.100.2.9.1.1.3INTEGERread-onlycurrent
performance24Index
OBJECT-TYPE
The index into the 24-hour performance table.
1.3.6.1.4.1.321.100.2.9.1.1.4INTEGER {performance24Summary(1), performance24Current(2), performance24period1(3), performance24period2(4), performance24period3(5), performance24period4(6), performance24period5(7), performance24period6(8), performance24period7(9), performance24period8(10), performance24period9(11), performance24period10(12), performance24period11(13), performance24period12(14), performance24period13(15), performance24period14(16), performance24period15(17), performance24period16(18), performance24period17(19), performance24period18(20), performance24period19(21), performance24period20(22), performance24period21(23), performance24period22(24), performance24period23(25), performance24period24(26), performance24period25(27), performance24period26(28), performance24period27(29), performance24period28(30), performance24period29(31), performance24period30(32), performance24period31(33), performance24period32(34), performance24period33(35), performance24period34(36), performance24period35(37), performance24period36(38), performance24period37(39), performance24period38(40), performance24period39(41), performance24period40(42), performance24period41(43), performance24period42(44), performance24period43(45), performance24period44(46), performance24period45(47), performance24period46(48), performance24period47(49), performance24period48(50), performance24period49(51), performance24period50(52), performance24period51(53), performance24period52(54), performance24period53(55), performance24period54(56), performance24period55(57), performance24period56(58), performance24period57(59), performance24period58(60), performance24period59(61), performance24period60(62), performance24period61(63), performance24period62(64), performance24period63(65), performance24period64(66), performance24period65(67), performance24period66(68), performance24period67(69), performance24period68(70), performance24period69(71), performance24period70(72), performance24period71(73), performance24period72(74), performance24period73(75), performance24period74(76), performance24period75(77), performance24period76(78), performance24period77(79), performance24period78(80), performance24period79(81), performance24period80(82), performance24period81(83), performance24period82(84), performance24period83(85), performance24period84(86), performance24period85(87), performance24period86(88), performance24period87(89), performance24period88(90), performance24period89(91), performance24period90(92), performance24period91(93), performance24period92(94), performance24period93(95), performance24period94(96), performance24period95(97), performance24period96(98)}read-onlycurrent
performance24ES
OBJECT-TYPE
The number of Errored Seconds for the 15-minute period.
1.3.6.1.4.1.321.100.2.9.1.1.5INTEGERread-onlycurrent
performance24BES
OBJECT-TYPE
The number of Bursty Errored Seconds for the 15-minute period.
1.3.6.1.4.1.321.100.2.9.1.1.6INTEGERread-onlycurrent
performance24SES
OBJECT-TYPE
The number of Severely Errored Seconds for the 15-minute period.
1.3.6.1.4.1.321.100.2.9.1.1.7INTEGERread-onlycurrent
performance24UAS
OBJECT-TYPE
The number of Unavailable Seconds for the 15-minute period.
1.3.6.1.4.1.321.100.2.9.1.1.8INTEGERread-onlycurrent
performance24LOFC
OBJECT-TYPE
The number of Loss of Frame Counts for the 15-minute period.
1.3.6.1.4.1.321.100.2.9.1.1.9INTEGERread-onlycurrent
performance24CSS
OBJECT-TYPE
The number of Controlled Slip Seconds for the 15-minute period.
1.3.6.1.4.1.321.100.2.9.1.1.10INTEGERread-onlycurrent
performance24CRCES
OBJECT-TYPE
The number of CRC Errored Seconds for the 15-minute period.
1.3.6.1.4.1.321.100.2.9.1.1.11INTEGERread-onlycurrent
performance24OOFS
OBJECT-TYPE
The number of Out of Frame Seconds for the 15-minute period.
1.3.6.1.4.1.321.100.2.9.1.1.12INTEGERread-onlycurrent
performance24LOSS
OBJECT-TYPE
The number of Loss of Signal Seconds for the 15-minute period.
1.3.6.1.4.1.321.100.2.9.1.1.13INTEGERread-onlycurrent
performance24AISS
OBJECT-TYPE
The number of Alarm Indication Signal Seconds for the 15-minute period.
1.3.6.1.4.1.321.100.2.9.1.1.14INTEGERread-onlycurrent
performance24RAS
OBJECT-TYPE
The number of Remote Alarm (Yellow) Seconds for the 15-minute period.
1.3.6.1.4.1.321.100.2.9.1.1.15INTEGERread-onlycurrent
performance24BPVS
OBJECT-TYPE
The number of Bipolar Violation Seconds for the 15-minute period.
1.3.6.1.4.1.321.100.2.9.1.1.16INTEGERread-onlycurrent
performance24timestamp
OBJECT-TYPE
The value of sysUpTime when the statistics were last updated.
1.3.6.1.4.1.321.100.2.9.1.1.17TimeTicksread-onlycurrent
performance30Table
OBJECT-TYPE
Performance table, contains TR54016 standard and enhanced 30-day data.
1.3.6.1.4.1.321.100.2.9.2not-accessiblecurrent
performance30TableEntry
OBJECT-TYPE
An entry in the performance30Table.
1.3.6.1.4.1.321.100.2.9.2.1not-accessiblecurrent
performance30NearIndex
OBJECT-TYPE
Selects the near device.
1.3.6.1.4.1.321.100.2.9.2.1.1INTEGERread-onlycurrent
performance30FarIndex
OBJECT-TYPE
Selects the far device.
1.3.6.1.4.1.321.100.2.9.2.1.2INTEGERread-onlycurrent
performance30InterfaceIndex
OBJECT-TYPE
Selects the interface.
1.3.6.1.4.1.321.100.2.9.2.1.3INTEGERread-onlycurrent
performance30Index
OBJECT-TYPE
The index into the 30-day performance table.
1.3.6.1.4.1.321.100.2.9.2.1.4INTEGER {performance30Summary(1), performance30day1(2), performance30day2(3), performance30day3(4), performance30day4(5), performance30day5(6), performance30day6(7), performance30day7(8), performance30day8(9), performance30day9(10), performance30day10(11), performance30day11(12), performance30day12(13), performance30day13(14), performance30day14(15), performance30day15(16), performance30day16(17), performance30day17(18), performance30day18(19), performance30day19(20), performance30day20(21), performance30day21(22), performance30day22(23), performance30day23(24), performance30day24(25), performance30day25(26), performance30day26(27), performance30day27(28), performance30day28(29), performance30day29(30), performance30day30(31)}read-onlycurrent
performance30ES
OBJECT-TYPE
The number of Errored Seconds for the 1-day period.
1.3.6.1.4.1.321.100.2.9.2.1.5INTEGERread-onlycurrent
performance30BES
OBJECT-TYPE
The number of Bursty Errored Seconds for the 1-day period.
1.3.6.1.4.1.321.100.2.9.2.1.6INTEGERread-onlycurrent
performance30SES
OBJECT-TYPE
The number of Severely Errored Seconds for the 1-day period.
1.3.6.1.4.1.321.100.2.9.2.1.7INTEGERread-onlycurrent
performance30UAS
OBJECT-TYPE
The number of Unavailable Seconds for the 1-day period.
1.3.6.1.4.1.321.100.2.9.2.1.8INTEGERread-onlycurrent
performance30LOFC
OBJECT-TYPE
The number of Loss of Frame Counts for the 1-day period.
1.3.6.1.4.1.321.100.2.9.2.1.9INTEGERread-onlycurrent
performance30CSS
OBJECT-TYPE
The number of Controlled Slip Seconds for the 1-day period.
1.3.6.1.4.1.321.100.2.9.2.1.10INTEGERread-onlycurrent
performance30CRCES
OBJECT-TYPE
The number of CRC Errored Seconds for the 1-day period.
1.3.6.1.4.1.321.100.2.9.2.1.11INTEGERread-onlycurrent
performance30OOFS
OBJECT-TYPE
The number of Out of Frame Seconds for the 1-day period.
1.3.6.1.4.1.321.100.2.9.2.1.12INTEGERread-onlycurrent
performance30LOSS
OBJECT-TYPE
The number of Loss of Signal Seconds for the 1-day period.
1.3.6.1.4.1.321.100.2.9.2.1.13INTEGERread-onlycurrent
performance30AISS
OBJECT-TYPE
The number of Alarm Indication Signal Seconds for the 1-day period.
1.3.6.1.4.1.321.100.2.9.2.1.14INTEGERread-onlycurrent
performance30RAS
OBJECT-TYPE
The number of Remote Alarm (Yellow) Seconds for the 1-day period.
1.3.6.1.4.1.321.100.2.9.2.1.15INTEGERread-onlycurrent
performance30BPVS
OBJECT-TYPE
The number of Bipolar Violation Seconds for the 1-day period.
1.3.6.1.4.1.321.100.2.9.2.1.16INTEGERread-onlycurrent
performance30timestamp
OBJECT-TYPE
The value of sysUpTime when the statistics were last updated.
1.3.6.1.4.1.321.100.2.9.2.1.17TimeTicksread-onlycurrent
itable
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.2.10
iTable
OBJECT-TYPE
The interface table.
1.3.6.1.4.1.321.100.2.10.1not-accessiblecurrent
iTableEntry
OBJECT-TYPE
An entry in the interface table.
1.3.6.1.4.1.321.100.2.10.1.1not-accessiblecurrent
iTableNearIndex
OBJECT-TYPE
Selects the near device.
1.3.6.1.4.1.321.100.2.10.1.1.1INTEGERread-onlycurrent
iTableFarIndex
OBJECT-TYPE
Selects the far device.
1.3.6.1.4.1.321.100.2.10.1.1.2INTEGERread-onlycurrent
iTableIndex
OBJECT-TYPE
The index into the interface table, used for addressing in above tables.
1.3.6.1.4.1.321.100.2.10.1.1.3INTEGERread-onlycurrent
iDescription
OBJECT-TYPE
Description of the interface.
1.3.6.1.4.1.321.100.2.10.1.1.4DisplayString (SIZE(0..80))read-onlycurrent
iType
OBJECT-TYPE
Enumerated interface type.
1.3.6.1.4.1.321.100.2.10.1.1.5INTEGER {disabled(0), v35(1), eia530(2), rs232(3), voice(4), hsdata(5), dualt1dte(6), dualddsv1(7), hexdds(8), ocudp(9), x21(10), dualddsv2(11), rfdl(128), alt(129), t1dte(130), didte(131), t1ntw(132), e1ntw(133), ddsntw(134), ddsdte(135), ddsdbu(136), fxs(137), fxo(138), eandm(139), e1sig(192)}read-onlycurrent
iSlot
OBJECT-TYPE
Device-dependent slot in which the interface resides.
1.3.6.1.4.1.321.100.2.10.1.1.6INTEGERread-onlycurrent
iPort
OBJECT-TYPE
Device-dependent port in which the interface resides.
1.3.6.1.4.1.321.100.2.10.1.1.7INTEGERread-onlycurrent
iStatus
OBJECT-TYPE
Status of the interface.
1.3.6.1.4.1.321.100.2.10.1.1.8INTEGER {iStatusOther(1), iStatusOK(2), iStatusErrored(3), iStatusAlarmed(4), iStatusTesting(5), iStatusUnassigned(6), iStatusLoopDetected(7)}read-onlycurrent
traplog
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.2.11
traplogTable
OBJECT-TYPE
The traplog table.
1.3.6.1.4.1.321.100.2.11.1not-accessiblecurrent
traplogEntry
OBJECT-TYPE
An entry in the traplog table.
1.3.6.1.4.1.321.100.2.11.1.1not-accessiblecurrent
traplogIndex
OBJECT-TYPE
The index into the traplog table.
1.3.6.1.4.1.321.100.2.11.1.1.1INTEGERread-onlycurrent
traplogNearIndex
OBJECT-TYPE
Specifies the near device.
1.3.6.1.4.1.321.100.2.11.1.1.2INTEGERread-onlycurrent
traplogFarIndex
OBJECT-TYPE
Specifies the far device.
1.3.6.1.4.1.321.100.2.11.1.1.3INTEGERread-onlycurrent
traplogInterfaceIndex
OBJECT-TYPE
Specifies the interface.
1.3.6.1.4.1.321.100.2.11.1.1.4INTEGERread-onlycurrent
traplogTrapNum
OBJECT-TYPE
The SNMP trap id.
1.3.6.1.4.1.321.100.2.11.1.1.5INTEGERread-onlycurrent
traplogTimeStamp
OBJECT-TYPE
Time the SNMP was generated.
1.3.6.1.4.1.321.100.2.11.1.1.6DisplayString (SIZE(0..40))read-onlycurrent
traplogDeviceType
OBJECT-TYPE
Specifies the device type for the trap.
1.3.6.1.4.1.321.100.2.11.1.1.7INTEGER {other(1), none(2), t12000(3), e12048(4), e13021(5), t13000(6), t13001(7), t13002(8), t13030(9), t13060(10), t13101(11), t13102(12), t13111(13), t13112(14), dds4001(15), dds4101(16), dds4051(17), dds4151(18), dds41TDM(19), generic54016(20), wanSuite(21)}read-onlycurrent
traplogOID1
OBJECT-TYPE
SNMP Object ID of 1st varbind.
1.3.6.1.4.1.321.100.2.11.1.1.8DisplayString (SIZE(0..80))read-onlycurrent
traplogDescription1
OBJECT-TYPE
Description of 1st varbind.
1.3.6.1.4.1.321.100.2.11.1.1.9DisplayString (SIZE(0..80))read-onlycurrent
traplogValue1
OBJECT-TYPE
Value of of 1st varbind.
1.3.6.1.4.1.321.100.2.11.1.1.10DisplayString (SIZE(0..80))read-onlycurrent
traplogOID2
OBJECT-TYPE
SNMP Object ID of 2nd varbind.
1.3.6.1.4.1.321.100.2.11.1.1.11DisplayString (SIZE(0..80))read-onlycurrent
traplogDescription2
OBJECT-TYPE
Description of 2nd varbind.
1.3.6.1.4.1.321.100.2.11.1.1.12DisplayString (SIZE(0..80))read-onlycurrent
traplogValue2
OBJECT-TYPE
Value of of 2nd varbind.
1.3.6.1.4.1.321.100.2.11.1.1.13DisplayString (SIZE(0..80))read-onlycurrent
traplogOID3
OBJECT-TYPE
SNMP Object ID of 3rd varbind.
1.3.6.1.4.1.321.100.2.11.1.1.14DisplayString (SIZE(0..80))read-onlycurrent
traplogDescription3
OBJECT-TYPE
Description of 3rd varbind.
1.3.6.1.4.1.321.100.2.11.1.1.15DisplayString (SIZE(0..80))read-onlycurrent
traplogValue3
OBJECT-TYPE
Value of of 3rd varbind.
1.3.6.1.4.1.321.100.2.11.1.1.16DisplayString (SIZE(0..80))read-onlycurrent
traplogDeleteEntry
OBJECT-TYPE
Writing the index of a trap to this object will delete the trap entry. Writing an index value of 0 will delete all entries.
1.3.6.1.4.1.321.100.2.11.2INTEGERread-writecurrent
traplogSortOption
OBJECT-TYPE
Determines the order in which traps are presented.
1.3.6.1.4.1.321.100.2.11.3INTEGER {other(1), ascendingtimestamp(2), ascendingunit(3)}read-writecurrent
traplogLastTimeStamp
OBJECT-TYPE
The timestamp of the newest trap in the trap log.
1.3.6.1.4.1.321.100.2.11.4TimeTicksread-onlycurrent
unitUtilities
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.2.12
unitUtilitiesTable
OBJECT-TYPE
The unit utilities table.
1.3.6.1.4.1.321.100.2.12.1not-accessiblecurrent
unitUtilitiesTableEntry
OBJECT-TYPE
An entry in the unit utilities table.
1.3.6.1.4.1.321.100.2.12.1.1not-accessiblecurrent
unitUtilitiesNearIndex
OBJECT-TYPE
Selects the near device.
1.3.6.1.4.1.321.100.2.12.1.1.1INTEGERread-onlycurrent
unitUtilitiesFarIndex
OBJECT-TYPE
Selects the far device.
1.3.6.1.4.1.321.100.2.12.1.1.2INTEGERread-onlycurrent
unitUtilitiesLocalPassword
OBJECT-TYPE
The password for local access to a device (VT100, front panel).
1.3.6.1.4.1.321.100.2.12.1.1.3DisplayStringread-writecurrent
unitUtilitiesTime
OBJECT-TYPE
This string is the current time as known to the device. The current time may be entered in this field using the HHMMSS format. For example, 3:45AM is entered as 034500 and 3:45PM is entered as 154500.
1.3.6.1.4.1.321.100.2.12.1.1.4DisplayString (SIZE(0..8))read-writecurrent
unitUtilitiesDate
OBJECT-TYPE
This string is the current date as known to the device. The current date may be entered in this field using the MMDDYY format. For example, July 4, 1997 is entered as 070497.
1.3.6.1.4.1.321.100.2.12.1.1.5DisplayString (SIZE(0..8))read-writecurrent
unitUtilitiesMaintenanceReset
OBJECT-TYPE
This field allows resetting the device to default values by reloading the start-up default configuration parameters.
1.3.6.1.4.1.321.100.2.12.1.1.6INTEGER {other(1), reset(2), restart(3), resetProfile1(4), resetProfile2(5), resetProfile3(6), resetProfile4(7), resetProfile5(8), resetProfile6(9), resetProfile7(10), resetProfile8(11), resetProfile9(12), resetProfile10(13), resetProfile11(14), resetProfile12(15), resetProfile13(16), resetProfile14(17), resetProfile15(18), resetProfile16(19), resetProfile17(20), resetProfile18(21), resetProfile19(22), resetProfile20(23), resetProfile21(24)}read-writecurrent
unitUtilitiesAlarmResetTimer
OBJECT-TYPE
This field allows setting a timer which will cause all existing alarms on the device to be cleared upon expiration. The counter is in seconds.
1.3.6.1.4.1.321.100.2.12.1.1.7INTEGERread-writecurrent
unitUtilitiesAlarmClear
OBJECT-TYPE
Writing a value of utilitiesAlarmClearNow(2) to this field causes all existing alarms to be cleared immediately.
1.3.6.1.4.1.321.100.2.12.1.1.8INTEGER {utilitiesAlarmClearOther(1), utilitiesAlarmClearNow(2)}read-writecurrent
unitUtilitiesSaveConfig
OBJECT-TYPE
This field commands the unit to save its configuration.
1.3.6.1.4.1.321.100.2.12.1.1.9INTEGER {other(1), saveConfig(2)}read-writecurrent
unitUtilitiesRestartStatus
OBJECT-TYPE
This parameter indicates if the unit configuration needs to be saved and restarted. notNeeded - A save and restart is not needed at this time. recommended - A save and restart is recommended for optimal performance but not required. required - A save and restart is required for the unit to implement the altered configuration.
1.3.6.1.4.1.321.100.2.12.1.1.10INTEGER {other(1), notNeeded(2), recommended(3), required(4)}read-onlycurrent
unitUtilitiesReadOnlyPassword
OBJECT-TYPE
The password for read only access to a device (VT100, front panel).
1.3.6.1.4.1.321.100.2.12.1.1.11DisplayStringread-writecurrent
unitUtilitiesPasswordLockoutEnable
OBJECT-TYPE
This parameter is used to enable or disable the password lockout feature.
1.3.6.1.4.1.321.100.2.12.1.1.12INTEGER {other(1), disabled(2), enabled(3)}read-writecurrent
unitUtilitiesPasswordLockoutStatus
OBJECT-TYPE
This parameter indicates if the password lockout feature is enabled or disabled, and if it is enabled this parameter may reflect if the password is indeed locked.
1.3.6.1.4.1.321.100.2.12.1.1.13INTEGER {other(1), disabled(2), enabled(3), locked(4)}read-onlycurrent
unitUtilitiesPasswordLockoutClear
OBJECT-TYPE
This parameter is used to unlock a locked password.
1.3.6.1.4.1.321.100.2.12.1.1.14INTEGER {other(1), unlock(2)}read-writecurrent
productInfo
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.2.13
productModelNumber
OBJECT-TYPE
This string displays the units model number
1.3.6.1.4.1.321.100.2.13.1DisplayString (SIZE(0..100))read-onlycurrent
productModelDescr
OBJECT-TYPE
This string displays a brief description of the unit
1.3.6.1.4.1.321.100.2.13.2DisplayString (SIZE(0..100))read-onlycurrent
productElementId
OBJECT-TYPE
This string is the same information that is in the element id field located in the utilities Screen of the unit's user interface. This field can be set from either location.
1.3.6.1.4.1.321.100.2.13.3DisplayString (SIZE(0..100))read-writecurrent
productSoftwareRev
OBJECT-TYPE
This string reports the units current software revision
1.3.6.1.4.1.321.100.2.13.4DisplayString (SIZE(0..100))read-onlycurrent
productHardwareRev
OBJECT-TYPE
This string reports the units hardware revision
1.3.6.1.4.1.321.100.2.13.5DisplayString (SIZE(0..100))read-onlycurrent
productSerialNum
OBJECT-TYPE
This string displays the unit's serial number
1.3.6.1.4.1.321.100.2.13.6DisplayString (SIZE(0..100))read-onlycurrent
productPhysicalAddress
OBJECT-TYPE
This string displays the unit's physical ethernet address
1.3.6.1.4.1.321.100.2.13.7DisplayString (SIZE(0..100))read-onlycurrent
productNmsAddress
OBJECT-TYPE
This string displays the unit's NMS address which is used to identify it to the TxPORT management products
1.3.6.1.4.1.321.100.2.13.8DisplayString (SIZE(0..100))read-onlycurrent
productLabelTable
OBJECT-TYPE
The Product Label Table.
1.3.6.1.4.1.321.100.2.13.9not-accessiblecurrent
productLabelTableEntry
OBJECT-TYPE
An entry in the product label table.
1.3.6.1.4.1.321.100.2.13.9.1not-accessiblecurrent
labelTableIndex
OBJECT-TYPE
The index into the ProductLabelTable.
1.3.6.1.4.1.321.100.2.13.9.1.1INTEGER (1..3)not-accessiblecurrent
labelTableLabel
OBJECT-TYPE
A product label.
1.3.6.1.4.1.321.100.2.13.9.1.2DisplayString (SIZE(0..20))read-writecurrent
labelTableValue
OBJECT-TYPE
The data associated with the label.
1.3.6.1.4.1.321.100.2.13.9.1.3DisplayString (SIZE(0..50))read-writecurrent
netAPS
OBJECT-IDENTITY
1.3.6.1.4.1.321.100.2.14
netAPSConfigTable
OBJECT-TYPE
One to One network Automatic Protection Switching (APS) configuration parameters table.
1.3.6.1.4.1.321.100.2.14.1not-accessiblecurrent
netAPSConfigTableEntry
OBJECT-TYPE
An entry in the netAPSConfigTable.
1.3.6.1.4.1.321.100.2.14.1.1not-accessiblecurrent
netAPSConfigNearIndex
OBJECT-TYPE
Selects the near device.
1.3.6.1.4.1.321.100.2.14.1.1.1INTEGERread-onlycurrent
netAPSConfigFarIndex
OBJECT-TYPE
Selects the far device.
1.3.6.1.4.1.321.100.2.14.1.1.2INTEGERread-onlycurrent
netAPSConfigifIndex
OBJECT-TYPE
Selects the MIB-II ifIndex.
1.3.6.1.4.1.321.100.2.14.1.1.3INTEGERread-onlycurrent
netAPSConfigOtherifIndex
OBJECT-TYPE
MIB-II ifIndex of the other interface involved with the APS.
1.3.6.1.4.1.321.100.2.14.1.1.4INTEGERread-writecurrent
netAPSConfigMode
OBJECT-TYPE
tr54017 - Implements TR54017 autoABswitch - Implements a single ended A/B switch between two independent lines masterAltCarrier - Master side of alternate carrier APS slaveAltCarrier - Slave side of alternate carrier APS
1.3.6.1.4.1.321.100.2.14.1.1.5INTEGER {other(1), tr54017(2), autoABswitch(3), masterAltCarrier(4), slaveAltCarrier(5)}read-writecurrent
netAPSConfigRevert
OBJECT-TYPE
disabled - Service does not return to the primary line until the backup line fails. enabled - Service automatically returns to the primary line when the primary line is able to carry service again.
1.3.6.1.4.1.321.100.2.14.1.1.6INTEGER {other(1), disabled(2), enabled(3)}read-writecurrent
netAPSConfigManualInhibit
OBJECT-TYPE
Disabled - Neither line is manually inhibited from carrying service. ThisLine - This line is manually inhibited from carrying service. OtherLine - The other line is manually inhibited from carrying service.
1.3.6.1.4.1.321.100.2.14.1.1.7INTEGER {other(1), disabled(2), thisLine(3), otherLine(4)}read-writecurrent
netAPSConfigAvailabilityTimer
OBJECT-TYPE
The line availability timer represents the minimum amount of time that is free of errors in active events that must expire before this line is returned to service availability. The timer is in seconds ranging from 0 - 900 seconds.
1.3.6.1.4.1.321.100.2.14.1.1.8INTEGERread-writecurrent
netAPSConfigESThreshold
OBJECT-TYPE
This parameter is the number of erred seconds in a 15-minute period needed before a transfer request is triggered. A setting of zero disables this trigger.
1.3.6.1.4.1.321.100.2.14.1.1.9INTEGERread-writecurrent
netAPSConfigESCount
OBJECT-TYPE
This parameter is the number of erred seconds in the current 15-minute interval. This count is reset at the beginning of a new 15-minute interval.
1.3.6.1.4.1.321.100.2.14.1.1.10INTEGERread-onlycurrent
netAPSConfigESSwitchEvent
OBJECT-TYPE
This status indicates if exceeding the ES threshold caused a transfer to the other line.
1.3.6.1.4.1.321.100.2.14.1.1.11INTEGER {other(1), normal(2), triggered(3)}read-onlycurrent
netAPSConfigCSESThreshold
OBJECT-TYPE
This parameter is the number of consecutive SES needed before a transfer request is triggered. A setting of zero disables this trigger.
1.3.6.1.4.1.321.100.2.14.1.1.12INTEGERread-writecurrent
netAPSConfigCSESCount
OBJECT-TYPE
This parameter is the number of consecutive SES detected. This count stops when 900 is reached and is reset when a non-SES is detected.
1.3.6.1.4.1.321.100.2.14.1.1.13INTEGERread-onlycurrent
netAPSConfigCSESSwitchEvent
OBJECT-TYPE
This status indicates if exceeding the consecutive SES threshold caused a transfer to the other line.
1.3.6.1.4.1.321.100.2.14.1.1.14INTEGER {other(1), normal(2), triggered(3)}read-onlycurrent
netAPSConfigStatusBitmap
OBJECT-TYPE
TR54017 defined bitmap status for this line interface: Value is 1 if this line is carrying service. Value is 2 if this line is in a failed state. Value is 4 if this line is in an inhibit state. Value is 8 if this line is looped back. Value is 16 if the other line is in a failed state. Value is 32 if the other line is in an inhibit state. Value is 64 if the other line is looped back. Value is 128 if the manual inhibit is active Note that multiple status conditions may exist at the same time. The failed state is determined when carrier fails, or the ES threshold is reached, or the consecutive SES threshold is reached. The inhibit state is set when the manual inhibit setting affects this line or the line is inhibited by the remote end.
1.3.6.1.4.1.321.100.2.14.1.1.15INTEGERread-onlycurrent
netAPSConfigStatusString
OBJECT-TYPE
ASCII string version of netAPSConfigStatusBitmap for this line status bits
1.3.6.1.4.1.321.100.2.14.1.1.16DisplayString (SIZE(0..80))read-onlycurrent
netAPSConfigTimeInInterval
OBJECT-TYPE
The number of seconds into the netAPSHist24Table current interval.
1.3.6.1.4.1.321.100.2.14.1.1.17INTEGERread-onlycurrent
netAPSConfigValidIntervals
OBJECT-TYPE
The number of valid intervals in the netAPSHist24Table
1.3.6.1.4.1.321.100.2.14.1.1.18INTEGERread-onlycurrent
netAPSConfigValidDays
OBJECT-TYPE
The number of valid days in the netAPSHist30Table
1.3.6.1.4.1.321.100.2.14.1.1.19INTEGERread-onlycurrent
netAPSConfigReset
OBJECT-TYPE
This action parameter does the following when the given value is set: other - Does nothing clearAlarms - Clear the APS events and counts clearHistory - Clear the APS history table statistics
1.3.6.1.4.1.321.100.2.14.1.1.20INTEGER {other(1), clearAlarms(2), clearHistory(3)}read-writecurrent
netAPSHist24Table
OBJECT-TYPE
History table, contains Network APS historical data.
1.3.6.1.4.1.321.100.2.14.2not-accessiblecurrent
netAPSHist24TableEntry
OBJECT-TYPE
An entry in the netAPSHist24Table.
1.3.6.1.4.1.321.100.2.14.2.1not-accessiblecurrent
netAPSHist24NearIndex
OBJECT-TYPE
Selects the near device.
1.3.6.1.4.1.321.100.2.14.2.1.1INTEGERread-onlycurrent
netAPSHist24FarIndex
OBJECT-TYPE
Selects the far device.
1.3.6.1.4.1.321.100.2.14.2.1.2INTEGERread-onlycurrent
netAPSHist24ifIndex
OBJECT-TYPE
Selects the MIB-II ifIndex.
1.3.6.1.4.1.321.100.2.14.2.1.3INTEGERread-onlycurrent
netAPSHist24Index
OBJECT-TYPE
The index into the 24-hour history table.
1.3.6.1.4.1.321.100.2.14.2.1.4INTEGER {statSummary(1), statCurrent(2), statPeriod1(3), statPeriod2(4), statPeriod3(5), statPeriod4(6), statPeriod5(7), statPeriod6(8), statPeriod7(9), statPeriod8(10), statPeriod9(11), statPeriod10(12), statPeriod11(13), statPeriod12(14), statPeriod13(15), statPeriod14(16), statPeriod15(17), statPeriod16(18), statPeriod17(19), statPeriod18(20), statPeriod19(21), statPeriod20(22), statPeriod21(23), statPeriod22(24), statPeriod23(25), statPeriod24(26), statPeriod25(27), statPeriod26(28), statPeriod27(29), statPeriod28(30), statPeriod29(31), statPeriod30(32), statPeriod31(33), statPeriod32(34), statPeriod33(35), statPeriod34(36), statPeriod35(37), statPeriod36(38), statPeriod37(39), statPeriod38(40), statPeriod39(41), statPeriod40(42), statPeriod41(43), statPeriod42(44), statPeriod43(45), statPeriod44(46), statPeriod45(47), statPeriod46(48), statPeriod47(49), statPeriod48(50), statPeriod49(51), statPeriod50(52), statPeriod51(53), statPeriod52(54), statPeriod53(55), statPeriod54(56), statPeriod55(57), statPeriod56(58), statPeriod57(59), statPeriod58(60), statPeriod59(61), statPeriod60(62), statPeriod61(63), statPeriod62(64), statPeriod63(65), statPeriod64(66), statPeriod65(67), statPeriod66(68), statPeriod67(69), statPeriod68(70), statPeriod69(71), statPeriod70(72), statPeriod71(73), statPeriod72(74), statPeriod73(75), statPeriod74(76), statPeriod75(77), statPeriod76(78), statPeriod77(79), statPeriod78(80), statPeriod79(81), statPeriod80(82), statPeriod81(83), statPeriod82(84), statPeriod83(85), statPeriod84(86), statPeriod85(87), statPeriod86(88), statPeriod87(89), statPeriod88(90), statPeriod89(91), statPeriod90(92), statPeriod91(93), statPeriod92(94), statPeriod93(95), statPeriod94(96), statPeriod95(97), statPeriod96(98)}read-onlycurrent
netAPSHist24Timestamp
OBJECT-TYPE
The value of sysUpTime when the statistics were last updated.
1.3.6.1.4.1.321.100.2.14.2.1.5TimeTicksread-onlycurrent
netAPSHist24StatusBitmap
OBJECT-TYPE
TR54017 defined bitmap status for this line interface: Value is 1 if this line is carrying service. Value is 2 if this line is in a failed state. Value is 4 if this line is in an inhibit state. Value is 8 if this line is looped back. Value is 16 if the other line is in a failed state. Value is 32 if the other line is in an inhibit state. Value is 64 if the other line is looped back. Value is 128 if the manual inhibit is active Note that multiple status conditions may exist at the same time. The failed state is determined when carrier fails, or the ES threshold is reached, or the consecutive SES threshold is reached. The inhibit state is set when the manual inhibit setting affects this line or the line is inhibited by the remote end.
1.3.6.1.4.1.321.100.2.14.2.1.6INTEGERread-onlycurrent
netAPSHist24StatusString
OBJECT-TYPE
ASCII string version of netAPSHist24StatusBitmap for this line status bits
1.3.6.1.4.1.321.100.2.14.2.1.7DisplayString (SIZE(0..80))read-onlycurrent
netAPSHist24Occurrences
OBJECT-TYPE
This parameter is the total number of times the service was transferred between lines.
1.3.6.1.4.1.321.100.2.14.2.1.8INTEGERread-onlycurrent
netAPSHist24Duration
OBJECT-TYPE
This parameter is the number of seconds the service was provided on this line.
1.3.6.1.4.1.321.100.2.14.2.1.9INTEGERread-onlycurrent
netAPSHist30Table
OBJECT-TYPE
History table, contains Network APS 30-day historical data.
1.3.6.1.4.1.321.100.2.14.3not-accessiblecurrent
netAPSHist30TableEntry
OBJECT-TYPE
An entry in the netAPSHist30Table.
1.3.6.1.4.1.321.100.2.14.3.1not-accessiblecurrent
netAPSHist30NearIndex
OBJECT-TYPE
Selects the near device.
1.3.6.1.4.1.321.100.2.14.3.1.1INTEGERread-onlycurrent
netAPSHist30FarIndex
OBJECT-TYPE
Selects the far device.
1.3.6.1.4.1.321.100.2.14.3.1.2INTEGERread-onlycurrent
netAPSHist30ifIndex
OBJECT-TYPE
Selects the MIB-II ifIndex.
1.3.6.1.4.1.321.100.2.14.3.1.3INTEGERread-onlycurrent
netAPSHist30Index
OBJECT-TYPE
The index into the 30-day history table.
1.3.6.1.4.1.321.100.2.14.3.1.4INTEGER {statSummary(1), statDay1(2), statDay2(3), statDay3(4), statDay4(5), statDay5(6), statDay6(7), statDay7(8), statDay8(9), statDay9(10), statDay10(11), statDay11(12), statDay12(13), statDay13(14), statDay14(15), statDay15(16), statDay16(17), statDay17(18), statDay18(19), statDay19(20), statDay20(21), statDay21(22), statDay22(23), statDay23(24), statDay24(25), statDay25(26), statDay26(27), statDay27(28), statDay28(29), statDay29(30), statDay30(31)}read-onlycurrent
netAPSHist30Timestamp
OBJECT-TYPE
The value of sysUpTime when the statistics were last updated.
1.3.6.1.4.1.321.100.2.14.3.1.5TimeTicksread-onlycurrent
netAPSHist30StatusBitmap
OBJECT-TYPE
TR54017 defined bitmap status for this line interface: Value is 1 if this line is carrying service. Value is 2 if this line is in a failed state. Value is 4 if this line is in an inhibit state. Value is 8 if this line is looped back. Value is 16 if the other line is in a failed state. Value is 32 if the other line is in an inhibit state. Value is 64 if the other line is looped back. Value is 128 if the manual inhibit is active Note that multiple status conditions may exist at the same time. The failed state is determined when carrier fails, or the ES threshold is reached, or the consecutive SES threshold is reached. The inhibit state is set when the manual inhibit setting affects this line or the line is inhibited by the remote end.
1.3.6.1.4.1.321.100.2.14.3.1.6INTEGERread-onlycurrent
netAPSHist30StatusString
OBJECT-TYPE
ASCII string version of netAPSHist30StatusBitmap for this line status bits
1.3.6.1.4.1.321.100.2.14.3.1.7DisplayString (SIZE(0..80))read-onlycurrent
netAPSHist30Occurrences
OBJECT-TYPE
This parameter is the total number of times the service was transferred between lines.
1.3.6.1.4.1.321.100.2.14.3.1.8INTEGERread-onlycurrent
netAPSHist30Duration
OBJECT-TYPE
This parameter is the number of seconds the service was provided on this line.
1.3.6.1.4.1.321.100.2.14.3.1.9INTEGERread-onlycurrent