MIBs Depot

CAMBIUM-PTP670-MIB

Registered at
1.3.6.1.4.1.17713
Last updated
2018-09-04 23:49
Organization
Cambium Networks Ltd.
Revisions
2018-09-04 23:49, 2018-05-25 18:14, 2017-11-24 09:19, 2017-09-06 16:59, 2017-06-15 18:31, 2017-02-24 11:59
Namespace
cambium
Source file
CAMBIUM-PTP670-MIB
Digest
sha256:e057827237ded4afa8f474f9b5daf05e40120af3e2337d7a574cbcba50841341

Description

MIB for non-line-of-sight (NLOS) wireless ethernet bridge.

Contact

Post: Simon Whitaker Cambium Networks Ltd. Unit B2, Linhay Business Park, Eastern Road, Ashburton, Devon. TQ13 7UP United Kingdom Phone: +44 (0) 1364 655 500 Email: simon.whitaker@cambiumnetworks.com

Imports

FromSymbols
INET-ADDRESS-MIBInetAddress, InetAddressType
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP
SNMPv2-SMICounter64, Integer32, IpAddress, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, enterprises, iso
SNMPv2-TCDisplayString, TEXTUAL-CONVENTION

Imported by

Nothing in this corpus imports this module.

Load order

Every file a consumer needs in order to load this module, dependencies first.

CAMBIUM-PTP670-MIB
INET-ADDRESS-MIB
SNMPv2-CONF
SNMPv2-SMI
SNMPv2-TC

Under this module's arcs

Where the registration tree carries on below this module.

ArcNameModule
1.3.6.1.4.1.17713.5ptp500CAMBIUM-PTP500-MIB
1.3.6.1.4.1.17713.6ptp600CAMBIUM-PTP600-MIB
1.3.6.1.4.1.17713.7ptp650CAMBIUM-PTP650-MIB
1.3.6.1.4.1.17713.8ptp800CAMBIUM-PTP800-MIB
1.3.6.1.4.1.17713.21pmpMibTreeCAMBIUM-PMP80211-MIB
1.3.6.1.4.1.17713.22cnPilotMIBCAMBIUM-MIB
1.3.6.1.4.1.17713.250ptp250CAMBIUM-PTP250-MIB

Objects

NameOIDSyntaxAccessStatus
ptp
OBJECT-IDENTITY
1.3.6.1.4.1.17713.1
ptmp
OBJECT-IDENTITY
1.3.6.1.4.1.17713.2
ptp670
OBJECT-IDENTITY
1.3.6.1.4.1.17713.11
dfs
OBJECT-IDENTITY
1.3.6.1.4.1.17713.11.3
dfsTableNumber
OBJECT-TYPE
Number of entries in the dfsTable
1.3.6.1.4.1.17713.11.3.1INTEGER (1..305)read-onlycurrent
dfsTable
OBJECT-TYPE
A table storing a snapshot of various DFS measurements for each channel
1.3.6.1.4.1.17713.11.3.2not-accessiblecurrent
dfsTableEntry
OBJECT-TYPE
Table DfsTable
1.3.6.1.4.1.17713.11.3.2.1not-accessiblecurrent
dfsTableIndex
OBJECT-TYPE
used to index values in the dfsTable.
1.3.6.1.4.1.17713.11.3.2.1.1INTEGER (1..305)not-accessiblecurrent
dfsMeans
OBJECT-TYPE
Snapshot of DFS means
1.3.6.1.4.1.17713.11.3.2.1.2Integer32read-onlycurrent
dfsNineNinePointNinePercentiles
OBJECT-TYPE
Snapshot of DFS 99.9 percentiles
1.3.6.1.4.1.17713.11.3.2.1.3Integer32read-onlycurrent
dfsPeaks
OBJECT-TYPE
Snapshot of DFS peaks
1.3.6.1.4.1.17713.11.3.2.1.4Integer32read-onlycurrent
extendedSpectrumScanning
OBJECT-TYPE
Enables Extended Spectrum Scanning
1.3.6.1.4.1.17713.11.3.3INTEGER {disabled(0), enabled(1)}read-onlycurrent
bridge
OBJECT-IDENTITY
1.3.6.1.4.1.17713.11.4
localPacketFiltering
OBJECT-TYPE
When Local Packet Filtering is Enabled, the unit keeps track of the port (Main, SFP, Aux or Wireless) on which a packet with a given MAC source address destined to the management agent has been received. This MAC address to port mapping is then used in order to route any response from the management agent to the right port. When Local Packet Filtering is Disabled, any Ethernet packet from the management agent is sent to all ports.
1.3.6.1.4.1.17713.11.4.1INTEGER {disabled(0), enabled(1)}read-writecurrent
packetsToInternalStack
OBJECT-TYPE
Total number of good packets the bridge has transmitted to the internal TCP/IP stack.
1.3.6.1.4.1.17713.11.4.2Counter64read-onlycurrent
packetsFromInternalStack
OBJECT-TYPE
Total number of good packets the bridge has received from the internal TCP/IP stack.
1.3.6.1.4.1.17713.11.4.3Counter64read-onlycurrent
configuration
OBJECT-IDENTITY
1.3.6.1.4.1.17713.11.5
iPv4Address
OBJECT-TYPE
Internet protocol (IPv4) address. This address is used by the family of Internet protocols to uniquely identify the unit on a network.
1.3.6.1.4.1.17713.11.5.1IpAddressread-writecurrent
subnetMask
OBJECT-TYPE
A subnet allows the flow of network traffic between hosts to be segregated based on a network configuration. By organizing hosts into logical groups, subnetting can improve network security and performance.
1.3.6.1.4.1.17713.11.5.2IpAddressread-writecurrent
gatewayIPAddress
OBJECT-TYPE
The IPv4 address of a device on the current network that acts as an IPv4 network gateway. A gateway acts as an entrance / exit to packets from / to other networks
1.3.6.1.4.1.17713.11.5.3IpAddressread-writecurrent
targetMACAddress
OBJECT-TYPE
MAC address of the unit forming the other end of the link
1.3.6.1.4.1.17713.11.5.4OCTET STRING (SIZE(6))read-onlycurrent
masterSlaveMode
OBJECT-TYPE
The wireless link operates using a master and slave relationship
1.3.6.1.4.1.17713.11.5.5INTEGER {master(0), slave(1)}read-writecurrent
maximumTransmitPower
OBJECT-TYPE
Maximum transmit power the wireless unit is permitted to use when establishing and maintaining the wireless link. This may be reduced during installation
1.3.6.1.4.1.17713.11.5.6INTEGER (-15..30)read-onlycurrent
antennaGain
OBJECT-TYPE
Antenna Gain. Expressed in 10ths of dBi.
1.3.6.1.4.1.17713.11.5.7INTEGER (100..610)read-writecurrent
cableLoss
OBJECT-TYPE
Loss in the cable between the ODU and the antenna. Expressed in 10ths of dB. NB: This attribute is ignored for variants with an integral antenna.
1.3.6.1.4.1.17713.11.5.8INTEGER (0..255)read-writecurrent
eIRP
OBJECT-TYPE
Effective Isotropic Radiated Power (EIRP) describes the strength of the radio signal leaving the wireless unit. Expressed in 10ths of dBm
1.3.6.1.4.1.17713.11.5.9Integer32read-onlycurrent
channelBandwidth
OBJECT-TYPE
This control sets the bandwidth of the transmit and receive radio channels
1.3.6.1.4.1.17713.11.5.11INTEGER {bw30MHz(0), bw15MHz(1), bw10MHz(2), bw5MHz(3), bw20MHz(4), bw56MHz(5), bw50MHz(6), bw40MHz(7), bw45MHz(8)}read-onlycurrent
linkName
OBJECT-TYPE
Name of the link allocated by the System Administrator. Used to establish a connection with the correct wireless unit at the other end of the link. NOTE: The link name MUST be the same at both ends of the link.
1.3.6.1.4.1.17713.11.5.14DisplayString (SIZE(0..63))read-writecurrent
siteName
OBJECT-TYPE
This field contains a user-provided description of the site name together with any additional notes
1.3.6.1.4.1.17713.11.5.15DisplayString (SIZE(0..63))read-writecurrent
accessMethod
OBJECT-TYPE
ODUs must be configured in pairs before a link can be established. The Access Method attribute determines how the paired ODUs will recognise each other. For the Link Access method, each ODU must be configured with Target MAC Address equal to the MAC Address of the other unit. For the Link Name Access method, both units must be configured with the same Link Name. For the Group Access method, both units must be configured with the same Group ID.
1.3.6.1.4.1.17713.11.5.16INTEGER {linkAccess(0), linkNameAccess(1), groupAccess(2)}read-onlycurrent
groupID
OBJECT-TYPE
When Access Method is set to Group Access, the Group ID identifies all the units belonging to the same group
1.3.6.1.4.1.17713.11.5.17INTEGER (0..255)read-writecurrent
iPv6Address
OBJECT-TYPE
Internet protocol (IPv6) address. This address is used by the family of Internet protocols to uniquely identify the unit on a network.
1.3.6.1.4.1.17713.11.5.18DisplayString (SIZE(0..39))read-writecurrent
iPVersion
OBJECT-TYPE
IP protocol selection. Choice of IPv4, IPv6 or Dual.
1.3.6.1.4.1.17713.11.5.20INTEGER {iPv4(0), iPv6(1), dualIPv4andIPv6(2)}read-writecurrent
iPv6AutoConfiguredLinkLocalAddress
OBJECT-TYPE
The auto configured link local IPv6 address
1.3.6.1.4.1.17713.11.5.21DisplayString (SIZE(0..39))read-onlycurrent
iPv6PrefixLength
OBJECT-TYPE
IPv6 prefix length
1.3.6.1.4.1.17713.11.5.22INTEGER (0..128)read-writecurrent
iPv6GatewayAddress
OBJECT-TYPE
The IPv6 address of a device on the current network that is currently acting as an IPv6 network gateway. A gateway acts as an entrance / exit to packets from / to other networks.
1.3.6.1.4.1.17713.11.5.23DisplayString (SIZE(0..39))read-writecurrent
remoteInternetAddressTypeLinked
OBJECT-TYPE
The type of Internet address specified by the associated remoteInternetAddressType.
1.3.6.1.4.1.17713.11.5.24INTEGER {unknown(0), ipv4(1), ipv6(2), ipv4z(3), ipv6z(4), unknown6(5), unknown7(6), unknown8(7), unknown9(8), unknown10(9), unknown11(10), unknown12(11), unknown13(12), unknown14(13), unknown15(14), unknown16(15), dns(16)}read-onlycurrent
remoteInternetAddressLinked
OBJECT-TYPE
INET address used to identify the peer wireless unit
1.3.6.1.4.1.17713.11.5.25InetAddressread-onlycurrent
subbandLowestFrequency
OBJECT-TYPE
Lowest center frequency of the subset of channels.
1.3.6.1.4.1.17713.11.5.26Integer32read-onlycurrent
subbandHighestFrequency
OBJECT-TYPE
Highest center frequency of the subset of channels.
1.3.6.1.4.1.17713.11.5.27Integer32read-onlycurrent
enableTransmission
OBJECT-TYPE
Control for enabling/disabling the radio transmitter of the Master. Note: Use Web Properties to control this feature.
1.3.6.1.4.1.17713.11.5.28INTEGER {enabled(0), muted(1)}read-writecurrent
antennaSelection
OBJECT-TYPE
Antenna Selection. Choice of Integrated or Connectorized
1.3.6.1.4.1.17713.11.5.29INTEGER {integrated(0), connectorized(1)}read-onlycurrent
transmitterChannels
OBJECT-TYPE
To select transmitter channel(s) (H,V)
1.3.6.1.4.1.17713.11.5.30INTEGER {handV(0), hOnly(1), vOnly(2)}read-writecurrent
wirelessTopology
OBJECT-TYPE
This attribute determines whether the device operates as part of a PTP or an HCMP network topology.
1.3.6.1.4.1.17713.11.5.31INTEGER {pointToPoint(0), highCapacityMultiPoint(1)}read-onlycurrent
configurationInstancedTableNumber
OBJECT-TYPE
Number of entries in the ConfigurationInstancedTable.
1.3.6.1.4.1.17713.11.5.32INTEGER (1..8)read-onlycurrent
configurationInstancedTable
OBJECT-TYPE
Instanced Public stats table.
1.3.6.1.4.1.17713.11.5.33not-accessiblecurrent
configurationInstancedTableEntry
OBJECT-TYPE
Table ConfigurationInstancedTable
1.3.6.1.4.1.17713.11.5.33.1not-accessiblecurrent
configurationInstancedTableIndex
OBJECT-TYPE
Used to index the ConfigurationInstancedTable.
1.3.6.1.4.1.17713.11.5.33.1.1INTEGER (1..8)not-accessiblecurrent
remoteInternetAddressType
OBJECT-TYPE
The type of Internet address specified by the associated remoteInternetAddressType.
1.3.6.1.4.1.17713.11.5.33.1.2INTEGER {unknown(0), ipv4(1), ipv6(2), ipv4z(3), ipv6z(4), unknown6(5), unknown7(6), unknown8(7), unknown9(8), unknown10(9), unknown11(10), unknown12(11), unknown13(12), unknown14(13), unknown15(14), unknown16(15), dns(16)}read-onlycurrent
remoteInternetAddress
OBJECT-TYPE
INET address used to identify the peer wireless unit
1.3.6.1.4.1.17713.11.5.33.1.3InetAddressread-onlycurrent
remoteUnitName
OBJECT-TYPE
This field contains user-provided name of the peer received over the wireless link
1.3.6.1.4.1.17713.11.5.33.1.4DisplayString (SIZE(0..63))read-onlycurrent
unitName
OBJECT-TYPE
This field contains user-provided name for this unit
1.3.6.1.4.1.17713.11.5.34DisplayString (SIZE(0..63))read-writecurrent
authorizationMethod
OBJECT-TYPE
Authorization Method to be used - Whitelist or Blacklist
1.3.6.1.4.1.17713.11.5.35INTEGER {whitelist(0), blacklist(1)}read-onlycurrent
remoteUnitNameLinked
OBJECT-TYPE
This field contains user-provided name of the peer received over the wireless link
1.3.6.1.4.1.17713.11.5.36DisplayString (SIZE(0..63))read-onlycurrent
ethernet
OBJECT-IDENTITY
1.3.6.1.4.1.17713.11.6
mainPSUPortAutoNegotiation
OBJECT-TYPE
This controls whether the local Ethernet interface configuration is automatically negotiated or forced. Do not use a forced setting together with auto negotiation at the Ethernet link partner. If you want to run your Ethernet link at a fixed speed and duplex then you would normally leave auto negotiation enabled and only enable the single Auto Neg Advertisement option that you want the link to run in - FORCING ETHERNET CONFIGURATION IS A LAST RESORT WHICH SHOULD ONLY BE PERFORMED IF YOU ARE HAVING PROBLEMS WITH AUTO NEGOTIATION - AND YOU MUST ENSURE THAT YOU CONFIGURE BOTH THIS UNIT AND THE ETHERNET LINK PARTNER TO WHICH IT IS CONNECTED IDENTICALLY (THE LINK PARTNER MUST NOT HAVE AUTO NEGOTIATION ENABLED EITHER, OTHERWISE A DUPLEX MISMATCH WILL OCCUR). NB: The new setting will only take effect after a system reboot.
1.3.6.1.4.1.17713.11.6.1INTEGER {disabled(0), enabled(1)}read-onlycurrent
mainPSUPortAutoNegAdvertisement
OBJECT-TYPE
This sets the different Ethernet configurations that will be advertised during auto negotiation. Note the new setting will only take effect after a system reboot. WARNING: Duplex mismatch may result if both ends of the Ethernet link do not have the same settings. Do not auto negotiation together with a fixed setting at the Ethernet link partner. WARNING: Make sure that you select option(s) that you know your connected equipment can cater for!
1.3.6.1.4.1.17713.11.6.2Bits {negInvalid(2), neg10MbpsHalfDuplex(3), neg10MbpsFullDuplex(4), neg100MbpsHalfDuplex(5), neg100MbpsFullDuplex(6), neg1000MbpsFullDuplex(7)}read-onlycurrent
mainPSUPortAutoMdix
OBJECT-TYPE
This enables/disables the Auto MDI/MDIX capability. NB: The new setting will only take effect after a system reboot
1.3.6.1.4.1.17713.11.6.3INTEGER {disabled(0), enabled(1)}read-onlycurrent
mainPSUPortStatus
OBJECT-TYPE
Current status of the Main PSU Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert
1.3.6.1.4.1.17713.11.6.4INTEGER {down(0), copperLinkUp(1), fiberLinkUp(2)}read-onlycurrent
mainPSUPortSpeedAndDuplex
OBJECT-TYPE
The current speed and duplex of the Main PSU Ethernet link
1.3.6.1.4.1.17713.11.6.5INTEGER {speed1000MbpsFullDuplex(0), speed100MbpsFullDuplex(1), speed100MbpsHalfDuplex(2), speed10MbpsFullDuplex(3), speed10MbpsHalfDuplex(4), speedUnknown6(5)}read-onlycurrent
dataPortWirelessDownAlert
OBJECT-TYPE
When enabled, this causes the Ethernet link to be dropped briefly when the wireless link drops. This is so that spanning tree algorithms can quickly detect that there is a problem.
1.3.6.1.4.1.17713.11.6.6INTEGER {disabled(0), enabled(1)}read-writecurrent
useVLANForManagementInterfaces
OBJECT-TYPE
This controls whether the management interfaces (WWW/SNMP/SMTP/SNTP) use VLAN tags or not. NB: The new setting will only take effect after a system reboot
1.3.6.1.4.1.17713.11.6.7INTEGER {noVLANTagging(0), iEEE8021QTaggedCTagType8100(1), iEEE8021adTaggedSTagorBTagType88a8(2)}read-writecurrent
vLANManagementPriority
OBJECT-TYPE
This VLAN Priority (0-7) will be included in packets generated by the management interfaces
1.3.6.1.4.1.17713.11.6.8INTEGER {p0(0), p1(1), p2(2), p3(3), p4(4), p5(5), p6(6), p7(7)}read-writecurrent
vLANManagementVID
OBJECT-TYPE
This VLAN VID (0-4094) will be included in packets generated by the management interfaces. Note the new setting will only take effect after a system reboot
1.3.6.1.4.1.17713.11.6.11INTEGER (0..4094)read-writecurrent
auxPortStatus
OBJECT-TYPE
Current status of the Aux Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert
1.3.6.1.4.1.17713.11.6.12INTEGER {down(0), copperLinkUp(1)}read-onlycurrent
auxPortSpeedAndDuplex
OBJECT-TYPE
The current speed and duplex of the Aux Ethernet link
1.3.6.1.4.1.17713.11.6.13INTEGER {speed1000MbpsFullDuplex(0), speed100MbpsFullDuplex(1), speed100MbpsHalfDuplex(2), speed10MbpsFullDuplex(3), speed10MbpsHalfDuplex(4), speedUnknown6(5)}read-onlycurrent
ethernetPriorityTableNumber
OBJECT-TYPE
Number of entries in the vLANPriorityTable.
1.3.6.1.4.1.17713.11.6.14INTEGER (9)read-onlycurrent
ethernetPriorityTable
OBJECT-TYPE
A priority queue mapping table. This is a list of packet queues indexed by Ethernet priority.
1.3.6.1.4.1.17713.11.6.15not-accessiblecurrent
ethernetPriorityTableEntry
OBJECT-TYPE
Table EthernetPriorityTable
1.3.6.1.4.1.17713.11.6.15.1not-accessiblecurrent
ethernetPriorityTableIndex
OBJECT-TYPE
Ethernet priority flag, used to index values in the ethernetPriorityTable
1.3.6.1.4.1.17713.11.6.15.1.1INTEGER {p0(1), p1(2), p2(3), p3(4), p4(5), p5(6), p6(7), p7(8), untagged(9)}not-accessiblecurrent
ethernetPriorityQueueMapping
OBJECT-TYPE
Configures the classification of this Ethernet priority (also known as IEEE 802.1p value) to an egress queue at the wireless port
1.3.6.1.4.1.17713.11.6.15.1.2INTEGER {q0(0), q1(1), q2(2), q3(3), q4(4), q5(5), q6(6), q7(7)}read-writecurrent
l2CPPriorityTableNumber
OBJECT-TYPE
Number of entries in the l2CPPriorityTable.
1.3.6.1.4.1.17713.11.6.16INTEGER (5)read-onlycurrent
l2CPPriorityTable
OBJECT-TYPE
A priority queue mapping table. This is a list of packet queues indexed by L2CP priority.
1.3.6.1.4.1.17713.11.6.17not-accessiblecurrent
l2CPPriorityTableEntry
OBJECT-TYPE
Table L2CPPriorityTable
1.3.6.1.4.1.17713.11.6.17.1not-accessiblecurrent
l2CPPriorityTableIndex
OBJECT-TYPE
L2CP priority flag, used to index values in the l2CPPriorityTable
1.3.6.1.4.1.17713.11.6.17.1.1INTEGER {bridge(1), mRP(2), cFM(3), rAPS(4), eAPS(5), pPPoEDiscoveryLCP(6)}not-accessiblecurrent
l2CPPriorityQueueMapping
OBJECT-TYPE
Configures the classification of this layer two control protocol (L2CP) to an egress queue at the wireless port
1.3.6.1.4.1.17713.11.6.17.1.2INTEGER {q0(0), q1(1), q2(2), q3(3), q4(4), q5(5), q6(6), q7(7)}read-writecurrent
iPDSCPPriorityTableNumber
OBJECT-TYPE
Number of entries in the iPDSCPPriorityTable.
1.3.6.1.4.1.17713.11.6.18INTEGER (64)read-onlycurrent
iPDSCPPriorityTable
OBJECT-TYPE
A priority queue mapping table. This is a list of packet queues indexed by L3 IP DSCP priority.
1.3.6.1.4.1.17713.11.6.19not-accessiblecurrent
iPDSCPPriorityTableEntry
OBJECT-TYPE
Table IPDSCPPriorityTable
1.3.6.1.4.1.17713.11.6.19.1not-accessiblecurrent
iPDSCPPriorityTableIndex
OBJECT-TYPE
IP DSCP priority flag, used to index values in the iPDSCPPriorityTable
1.3.6.1.4.1.17713.11.6.19.1.1INTEGER (1..64)not-accessiblecurrent
iPDSCPPriorityQueueMapping
OBJECT-TYPE
Configures the classification of this IP differentiated services code point (DSCP) value to an egress queue at the wireless port
1.3.6.1.4.1.17713.11.6.19.1.2INTEGER {q0(0), q1(1), q2(2), q3(3), q4(4), q5(5), q6(6), q7(7)}read-writecurrent
mPLSTCPriorityTableNumber
OBJECT-TYPE
Number of entries in the mPLSTCPriorityTable.
1.3.6.1.4.1.17713.11.6.20INTEGER (8)read-onlycurrent
mPLSTCPriorityTable
OBJECT-TYPE
A priority queue mapping table. This is a list of priority queues indexed by MPLS TC priority.
1.3.6.1.4.1.17713.11.6.21not-accessiblecurrent
mPLSTCPriorityTableEntry
OBJECT-TYPE
Table MPLSTCPriorityTable
1.3.6.1.4.1.17713.11.6.21.1not-accessiblecurrent
mPLSTCPriorityTableIndex
OBJECT-TYPE
MPLS TC priority flag, used to index values in the mPLSTCPriorityTable
1.3.6.1.4.1.17713.11.6.21.1.1INTEGER (1..8)not-accessiblecurrent
mPLSTCPriorityQueueMapping
OBJECT-TYPE
Configures the classification of this MPLS traffic class (the field formerly known as EXP) to an egress queue at the wireless port
1.3.6.1.4.1.17713.11.6.21.1.2INTEGER {q0(0), q1(1), q2(2), q3(3), q4(4), q5(5), q6(6), q7(7)}read-writecurrent
managementPortWirelessDownAlert
OBJECT-TYPE
When enabled, this causes the management link to be dropped briefly when the wireless link drops. This is so that spanning tree algorithms can quickly detect that there is a problem.
1.3.6.1.4.1.17713.11.6.23INTEGER {disabled(0), enabled(1)}read-writecurrent
qOSPriorityScheme
OBJECT-TYPE
Selects classification based on fields in the Ethernet header (Layer 2) or in the Network header (Layer 3). The unit recognises two network layer protocols: IP and MPLS
1.3.6.1.4.1.17713.11.6.24INTEGER {ethernet(0), iPMPLS(1)}read-writecurrent
unknownNetworkPriorityQueueMapping
OBJECT-TYPE
Configures the classification of unknown network protocols to an egress queue at the wireless port. Unknown means something other than IP and MPLS
1.3.6.1.4.1.17713.11.6.25INTEGER {q0(0), q1(1), q2(2), q3(3), q4(4), q5(5), q6(6), q7(7)}read-writecurrent
dSCPManagementPriority
OBJECT-TYPE
This Differentiated Services Code Point value will be inserted in the IP Header of all IP Datagrams transmitted by the management interfaces
1.3.6.1.4.1.17713.11.6.26INTEGER (0..63)read-onlycurrent
dataBridgingStatusLinked
OBJECT-TYPE
Current status of Ethernet Data traffic bridging over the wireless link
1.3.6.1.4.1.17713.11.6.27INTEGER {disabled(0), enabled(1)}read-onlycurrent
mainPSUPortAllocation
OBJECT-TYPE
Indicates the service or services supported by the Main PSU Ethernet port
1.3.6.1.4.1.17713.11.6.28INTEGER {disabled(0), dataOnly(1), dataandInBandManagement(2), outofBandLocalManagement(3), outofBandRemoteManagement(4)}read-onlycurrent
auxPortAllocation
OBJECT-TYPE
Indicates the service or services supported by the Aux Ethernet port
1.3.6.1.4.1.17713.11.6.29INTEGER {disabled(0), dataOnly(1), dataandInBandManagement(2), outofBandLocalManagement(3), outofBandRemoteManagement(4)}read-onlycurrent
sFPPortAllocation
OBJECT-TYPE
Indicates the service or services supported by the SFP Ethernet port
1.3.6.1.4.1.17713.11.6.30INTEGER {disabled(0), dataOnly(1), dataandInBandManagement(2), outofBandLocalManagement(3), outofBandRemoteManagement(4)}read-onlycurrent
dataPortPauseFrames
OBJECT-TYPE
Controls whether the bridge tunnels or discards Layer 2 PAUSE frames arriving at the Data Port. Such frames are identified by the destination MAC Address being equal to 01-80-C2-00-00-01
1.3.6.1.4.1.17713.11.6.31INTEGER {tunnel(0), discard(1)}read-onlycurrent
sFPPortAutoNegotiation
OBJECT-TYPE
This controls whether the local SFP Ethernet interface configuration is automatically negotiated or forced. Do not use a forced setting together with auto negotiation at the Ethernet link partner. If you want to run your Ethernet link at a fixed speed and duplex then you would normally leave auto negotiation enabled and only enable the single Auto Neg Advertisement option that you want the link to run in - FORCING ETHERNET CONFIGURATION IS A LAST RESORT WHICH SHOULD ONLY BE PERFORMED IF YOU ARE HAVING PROBLEMS WITH AUTO NEGOTIATION - AND YOU MUST ENSURE THAT YOU CONFIGURE BOTH THIS UNIT AND THE ETHERNET LINK PARTNER TO WHICH IT IS CONNECTED IDENTICALLY (THE LINK PARTNER MUST NOT HAVE AUTO NEGOTIATION ENABLED EITHER, OTHERWISE A DUPLEX MISMATCH WILL OCCUR). NB: The new setting will only take effect after a system reboot.
1.3.6.1.4.1.17713.11.6.32INTEGER {disabled(0), enabled(1)}read-onlycurrent
sFPPortAutoNegAdvertisement
OBJECT-TYPE
This sets the different SFP Ethernet configurations that will be advertised during auto negotiation. Note the new setting will only take effect after a system reboot. WARNING: Duplex mismatch may result if both ends of the Ethernet link do not have the same settings. Do not auto negotiation together with a fixed setting at the Ethernet link partner. WARNING: Make sure that you select option(s) that you know your connected equipment can cater for!
1.3.6.1.4.1.17713.11.6.33Bits {negInvalid(2), neg10MbpsHalfDuplex(3), neg10MbpsFullDuplex(4), neg100MbpsHalfDuplex(5), neg100MbpsFullDuplex(6), neg1000MbpsFullDuplex(7)}read-onlycurrent
sFPPortAutoMdix
OBJECT-TYPE
This enables/disables the Auto MDI/MDIX capability. NB: The new setting will only take effect after a system reboot
1.3.6.1.4.1.17713.11.6.34INTEGER {disabled(0), enabled(1)}read-onlycurrent
sFPPortStatus
OBJECT-TYPE
Current status of the SFP Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert
1.3.6.1.4.1.17713.11.6.35INTEGER {down(0), copperLinkUp(1), fiberLinkUp(2)}read-onlycurrent
sFPPortSpeedAndDuplex
OBJECT-TYPE
The current speed and duplex of the SFP Ethernet link
1.3.6.1.4.1.17713.11.6.36INTEGER {speed1000MbpsFullDuplex(0), speed100MbpsFullDuplex(1), speed100MbpsHalfDuplex(2), speed10MbpsFullDuplex(3), speed10MbpsHalfDuplex(4), speedUnknown6(5)}read-onlycurrent
auxPortPowerOverEthernetOutput
OBJECT-TYPE
The state of the Power Over Ethernet (PoE) output of the Aux port. Enabling PoE output may lead to system instability; please refer to the User Guide before enabling this control
1.3.6.1.4.1.17713.11.6.37INTEGER {disabled(0), enabled(1)}read-onlycurrent
auxPortPowerOverEthernetOutputStatus
OBJECT-TYPE
Current status of the Power Over Ethernet (PoE) output of the Aux port
1.3.6.1.4.1.17713.11.6.38INTEGER {poEOutputOn(0), poEOutputDisabled(1), poEOutputEnabledbutNotActiveErrororNoLoadPresent(2), poEOutputOverloadError(3), poEOutputOverTempError(4), poEOutputErrorDetected(5)}read-onlycurrent
syncETracking
OBJECT-TYPE
Controls whether Synchronous Ethernet (SyncE) network synchronization is enabled.
1.3.6.1.4.1.17713.11.6.39INTEGER {disabled(0), enabled(1), internalTDMUseOnly(2)}read-writecurrent
syncEEquipmentClock
OBJECT-TYPE
EEC-Option 1 applies to synchronous Ethernet equipments that are designed to interwork with networks optimized for the 2048-kbit/s hierarchy. Corresponds to ITU-T G.813 Option 1; EEC-Option 2 applies to synchronous Ethernet equipments that are designed to interwork with networks optimized for the 1544-kbit/s hierarchy. Corresponds to Type IV clock from ITU-T G.812.
1.3.6.1.4.1.17713.11.6.40INTEGER {eECOption1(0), eECOption2(1)}read-writecurrent
mainPSUPortQLRxOverwrite
OBJECT-TYPE
Override for the Synchronous Ethernet (SyncE) received Quality Level (QL) on the main PSU port.
1.3.6.1.4.1.17713.11.6.41INTEGER {disabled(0), qLPRS(1), qLSTU(2), qLPRC(3), qLST2(4), qLSSUAQLTNC(5), qLSSUB(6), qLST3E(7), qLEEC2QLST3(8), qLEEC1QLSEC(9), qLSMC(10), qLPROV(11), qLDNUQLDUS(12)}read-writecurrent
mainPSUPortSSMTx
OBJECT-TYPE
Controls whether the Synchronous Ethernet (SyncE) Quality Level (QL) is transmitted on the Main PSU port
1.3.6.1.4.1.17713.11.6.42INTEGER {disabled(0), enabled(1)}read-writecurrent
sFPPortSSMTx
OBJECT-TYPE
Controls whether the Synchronous Ethernet (SyncE) Quality Level (QL) is transmitted on the SFP port
1.3.6.1.4.1.17713.11.6.43INTEGER {disabled(0), enabled(1)}read-writecurrent
auxPortSSMTx
OBJECT-TYPE
Controls whether the Synchronous Ethernet (SyncE) Quality Level (QL) is transmitted on the Aux port
1.3.6.1.4.1.17713.11.6.44INTEGER {disabled(0), enabled(1)}read-writecurrent
syncETrackingState
OBJECT-TYPE
The current state of Synchronous Ethernet (SyncE) network synchronization.
1.3.6.1.4.1.17713.11.6.45INTEGER {disabled(0), acquiringWirelessLock(1), freeRunning(2), lockedLocalAcquiringHoldover(3), lockedLocalHoldoverAcquired(4), holdover(5), lockedRemoteAcquiringHoldover(6), lockedRemoteHoldoverAcquired(7)}read-onlycurrent
mainPSUPortQLRx
OBJECT-TYPE
The Synchronous Ethernet (SyncE) Quality Level (QL) currently being received on the main PSU port.
1.3.6.1.4.1.17713.11.6.46INTEGER {none(0), qLPRS(1), qLSTU(2), qLPRC(3), qLST2(4), qLSSUAQLTNC(5), qLSSUB(6), qLST3E(7), qLEEC2QLST3(8), qLEEC1QLSEC(9), qLSMC(10), qLPROV(11), qLDNUQLDUS(12), qLFAILED(13)}read-onlycurrent
auxPortQLRx
OBJECT-TYPE
The Synchronous Ethernet (SyncE) Quality Level (QL) currently being received on the auxiliary port.
1.3.6.1.4.1.17713.11.6.47INTEGER {none(0), qLPRS(1), qLSTU(2), qLPRC(3), qLST2(4), qLSSUAQLTNC(5), qLSSUB(6), qLST3E(7), qLEEC2QLST3(8), qLEEC1QLSEC(9), qLSMC(10), qLPROV(11), qLDNUQLDUS(12), qLFAILED(13)}read-onlycurrent
sFPPortQLRx
OBJECT-TYPE
The Synchronous Ethernet (SyncE) Quality Level (QL) currently being received on the SFP port.
1.3.6.1.4.1.17713.11.6.48INTEGER {none(0), qLPRS(1), qLSTU(2), qLPRC(3), qLST2(4), qLSSUAQLTNC(5), qLSSUB(6), qLST3E(7), qLEEC2QLST3(8), qLEEC1QLSEC(9), qLSMC(10), qLPROV(11), qLDNUQLDUS(12), qLFAILED(13)}read-onlycurrent
mainPSUPortQLTx
OBJECT-TYPE
The Synchronous Ethernet (SyncE) transmit Quality Level (QL) of the main PSU port.
1.3.6.1.4.1.17713.11.6.49INTEGER {none(0), qLPRS(1), qLSTU(2), qLPRC(3), qLST2(4), qLSSUAQLTNC(5), qLSSUB(6), qLST3E(7), qLEEC2QLST3(8), qLEEC1QLSEC(9), qLSMC(10), qLPROV(11), qLDNUQLDUS(12)}read-onlycurrent
auxPortQLTx
OBJECT-TYPE
The Synchronous Ethernet (SyncE) transmit Quality Level (QL) of the auxiliary port.
1.3.6.1.4.1.17713.11.6.50INTEGER {none(0), qLPRS(1), qLSTU(2), qLPRC(3), qLST2(4), qLSSUAQLTNC(5), qLSSUB(6), qLST3E(7), qLEEC2QLST3(8), qLEEC1QLSEC(9), qLSMC(10), qLPROV(11), qLDNUQLDUS(12)}read-onlycurrent
sFPPortQLTx
OBJECT-TYPE
The Synchronous Ethernet (SyncE) transmit Quality Level (QL) of the SFP port.
1.3.6.1.4.1.17713.11.6.51INTEGER {none(0), qLPRS(1), qLSTU(2), qLPRC(3), qLST2(4), qLSSUAQLTNC(5), qLSSUB(6), qLST3E(7), qLEEC2QLST3(8), qLEEC1QLSEC(9), qLSMC(10), qLPROV(11), qLDNUQLDUS(12)}read-onlycurrent
mainPSUPortSyncEMasterSlaveStatus
OBJECT-TYPE
The main PSU port Synchronous Ethernet (SyncE) Master/Slave status
1.3.6.1.4.1.17713.11.6.52INTEGER {master(0), slave(1)}read-onlycurrent
auxPortSyncEMasterSlaveStatus
OBJECT-TYPE
The auxiliary port Synchronous Ethernet (SyncE) Master/Slave status
1.3.6.1.4.1.17713.11.6.53INTEGER {master(0), slave(1)}read-onlycurrent
sFPPortSyncEMasterSlaveStatus
OBJECT-TYPE
The SFP port Synchronous Ethernet (SyncE) Master/Slave status
1.3.6.1.4.1.17713.11.6.54INTEGER {master(0), slave(1)}read-onlycurrent
mainPSUPortGigabitMasterSlaveStatus
OBJECT-TYPE
The main PSU port Gigabit Ethernet Master/Slave status
1.3.6.1.4.1.17713.11.6.55INTEGER {master(0), slave(1), notApplicable(2)}read-onlycurrent
auxPortGigabitMasterSlaveStatus
OBJECT-TYPE
The auxiliary port Gigabit Ethernet Master/Slave status
1.3.6.1.4.1.17713.11.6.56INTEGER {master(0), slave(1), notApplicable(2)}read-onlycurrent
sFPPortGigabitMasterSlaveStatus
OBJECT-TYPE
The SFP port Gigabit Ethernet Master/Slave status
1.3.6.1.4.1.17713.11.6.57INTEGER {master(0), slave(1), notApplicable(2)}read-onlycurrent
transparentClock
OBJECT-TYPE
This control enables the Precision Time Protocol (IEEE-1588) Transparent Clock. Once enabled the unit will modify the correction field in PTP event messages to take account of the time these frames have been resident in this system. This will happen for all PTP frames at Layer 2 & Layer 3 (IPv4 & IPv6) unless a transparent clock VLAN is enabled.
1.3.6.1.4.1.17713.11.6.58INTEGER {disabled(0), enabled(1)}read-writecurrent
transparentClockVLAN
OBJECT-TYPE
If All is selected then all PTP frames will have their correction fields modified with the residence time. If an S-TAG or C-TAG is selected, only frames with this VLAN tag and matching the VLAN ID in the Transparent Clock VID will have their correction fields modified.
1.3.6.1.4.1.17713.11.6.59INTEGER {all(0), sTagged(1), cTagged(2)}read-writecurrent
transparentClockVID
OBJECT-TYPE
The VLAN ID which frames must match if they are to be corrected. Only valid when an S-TAG or C-TAG has been selected.
1.3.6.1.4.1.17713.11.6.60INTEGER (0..4094)read-writecurrent
mainPSUPortAcceptedQLRx
OBJECT-TYPE
The Synchronous Ethernet (SyncE) Quality Level (QL) currently accepted (validated) on the main PSU port.
1.3.6.1.4.1.17713.11.6.61INTEGER {none(0), qLPRS(1), qLSTU(2), qLPRC(3), qLST2(4), qLSSUAQLTNC(5), qLSSUB(6), qLST3E(7), qLEEC2QLST3(8), qLEEC1QLSEC(9), qLSMC(10), qLPROV(11), qLDNUQLDUS(12), qLFAILED(13)}read-onlycurrent
auxPortAcceptedQLRx
OBJECT-TYPE
The Synchronous Ethernet (SyncE) Quality Level (QL) currently accepted (validated) on the auxiliary port.
1.3.6.1.4.1.17713.11.6.62INTEGER {none(0), qLPRS(1), qLSTU(2), qLPRC(3), qLST2(4), qLSSUAQLTNC(5), qLSSUB(6), qLST3E(7), qLEEC2QLST3(8), qLEEC1QLSEC(9), qLSMC(10), qLPROV(11), qLDNUQLDUS(12), qLFAILED(13)}read-onlycurrent
sFPPortAcceptedQLRx
OBJECT-TYPE
The Synchronous Ethernet (SyncE) Quality Level (QL) currently accepted (validated) on the SFP port.
1.3.6.1.4.1.17713.11.6.63INTEGER {none(0), qLPRS(1), qLSTU(2), qLPRC(3), qLST2(4), qLSSUAQLTNC(5), qLSSUB(6), qLST3E(7), qLEEC2QLST3(8), qLEEC1QLSEC(9), qLSMC(10), qLPROV(11), qLDNUQLDUS(12), qLFAILED(13)}read-onlycurrent
mainPSUPortSyncERxStatus
OBJECT-TYPE
The Synchronous Ethernet (SyncE) Receive Status of the main PSU port
1.3.6.1.4.1.17713.11.6.64INTEGER {good(0), waittoRestore(1), failed(2)}read-onlycurrent
auxPortSyncERxStatus
OBJECT-TYPE
The Synchronous Ethernet (SyncE) Receive Status of the auxiliary port
1.3.6.1.4.1.17713.11.6.65INTEGER {good(0), waittoRestore(1), failed(2)}read-onlycurrent
sFPPortSyncERxStatus
OBJECT-TYPE
The Synchronous Ethernet (SyncE) Receive Status of the SFP port
1.3.6.1.4.1.17713.11.6.66INTEGER {good(0), waittoRestore(1), failed(2)}read-onlycurrent
nIDULanPortStatus
OBJECT-TYPE
Current status of the NIDU LAN Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert
1.3.6.1.4.1.17713.11.6.67INTEGER {down(0), copperLinkUp(1), fiberLinkUp(2)}read-onlycurrent
nIDULanPortSpeedAndDuplex
OBJECT-TYPE
The current speed and duplex of the Ethernet link to the NIDU LAN Port
1.3.6.1.4.1.17713.11.6.68INTEGER {speed1000MbpsFullDuplex(0), speed100MbpsFullDuplex(1), speed100MbpsHalfDuplex(2), speed10MbpsFullDuplex(3), speed10MbpsHalfDuplex(4), speedUnknown6(5)}read-onlycurrent
oOBPriorityQueueMapping
OBJECT-TYPE
Configures the classification of traffic to an egress queue at the wireless port
1.3.6.1.4.1.17713.11.6.69INTEGER {q0(0), q1(1), q2(2), q3(3), q4(4), q5(5), q6(6), q7(7)}read-writecurrent
nIDULanPortAutoNegotiation
OBJECT-TYPE
This controls whether the local Ethernet interface configuration is automatically negotiated or forced. Do not use a forced setting together with auto negotiation at the Ethernet link partner. If you want to run your Ethernet link at a fixed speed and duplex then you would normally leave auto negotiation enabled and only enable the single Auto Neg Advertisement option that you want the link to run in - FORCING ETHERNET CONFIGURATION IS A LAST RESORT WHICH SHOULD ONLY BE PERFORMED IF YOU ARE HAVING PROBLEMS WITH AUTO NEGOTIATION - AND YOU MUST ENSURE THAT YOU CONFIGURE BOTH THIS UNIT AND THE ETHERNET LINK PARTNER TO WHICH IT IS CONNECTED IDENTICALLY (THE LINK PARTNER MUST NOT HAVE AUTO NEGOTIATION ENABLED EITHER, OTHERWISE A DUPLEX MISMATCH WILL OCCUR). NB: The new setting will only take effect after a system reboot.
1.3.6.1.4.1.17713.11.6.70INTEGER {disabled(0), enabled(1)}read-onlycurrent
nIDULanPortAutoNegAdvertisement
OBJECT-TYPE
This sets the different Ethernet configurations that will be advertised during auto negotiation. Note the new setting will only take effect after a system reboot. WARNING: Duplex mismatch may result if both ends of the Ethernet link do not have the same settings. Do not auto negotiation together with a fixed setting at the Ethernet link partner. WARNING: Make sure that you select option(s) that you know your connected equipment can cater for!
1.3.6.1.4.1.17713.11.6.71Bits {negInvalid(2), neg10MbpsHalfDuplex(3), neg10MbpsFullDuplex(4), neg100MbpsHalfDuplex(5), neg100MbpsFullDuplex(6), neg1000MbpsFullDuplex(7)}read-onlycurrent
nIDULanPortAutoMdix
OBJECT-TYPE
This enables/disables the Auto MDI/MDIX capability. NB: The new setting will only take effect after a system reboot
1.3.6.1.4.1.17713.11.6.72INTEGER {disabled(0), enabled(1)}read-onlycurrent
nIDULanPortGigabitMasterSlaveStatus
OBJECT-TYPE
The NIDU LAN port Gigabit Ethernet Master/Slave status
1.3.6.1.4.1.17713.11.6.73INTEGER {master(0), slave(1), notApplicable(2)}read-onlycurrent
txMABFrames
OBJECT-TYPE
Number of MAB frames transmitted
1.3.6.1.4.1.17713.11.6.74Integer32read-onlycurrent
managementNetworkAccessEnabled
OBJECT-TYPE
When enabled the local Out-of-Band interface can be used to access the remote management network. If not enabled the local management agent can still be accessed from the remote management network and the local Out-of-Band interface
1.3.6.1.4.1.17713.11.6.75INTEGER {no(0), yes(1)}read-writecurrent
transparentClockPort
OBJECT-TYPE
IEEE 1588 Transparent Clock source
1.3.6.1.4.1.17713.11.6.81INTEGER {mainPSU(0), aux(1), sFP(2), mainPSUplusAux(3), mainPSUplusSFP(4), auxplusSFP(5), mainPSUplusAuxplusSFP(6)}read-writecurrent
syncESlavePort
OBJECT-TYPE
Select a Sync E Slave Port
1.3.6.1.4.1.17713.11.6.82INTEGER {mainPSUPort(0), sFPPort(1)}read-writecurrent
sFPPortQLRxOverwrite
OBJECT-TYPE
Override for the Synchronous Ethernet (SyncE) received Quality Level (QL) on the SFP Port.
1.3.6.1.4.1.17713.11.6.83INTEGER {disabled(0), qLPRS(1), qLSTU(2), qLPRC(3), qLST2(4), qLSSUAQLTNC(5), qLSSUB(6), qLST3E(7), qLEEC2QLST3(8), qLEEC1QLSEC(9), qLSMC(10), qLPROV(11), qLDNUQLDUS(12)}read-writecurrent
ethernetInstancedTableNumber
OBJECT-TYPE
Number of entries in the ethernetInstancedTable.
1.3.6.1.4.1.17713.11.6.84INTEGER (1..8)read-onlycurrent
ethernetInstancedTable
OBJECT-TYPE
Instanced table showing the ethernet status
1.3.6.1.4.1.17713.11.6.85not-accessiblecurrent
ethernetInstancedTableEntry
OBJECT-TYPE
Table EthernetInstancedTable
1.3.6.1.4.1.17713.11.6.85.1not-accessiblecurrent
ethernetInstancedTableIndex
OBJECT-TYPE
Used to index the ethernetInstancedTable.
1.3.6.1.4.1.17713.11.6.85.1.1INTEGER (1..8)not-accessiblecurrent
dataBridgingStatus
OBJECT-TYPE
Current status of Ethernet Data traffic bridging over the wireless link
1.3.6.1.4.1.17713.11.6.85.1.2INTEGER {disabled(0), enabled(1)}read-onlycurrent
ethernetStatisticsTableNumber
OBJECT-TYPE
Number of entries in the ethernetStatisticsTable.
1.3.6.1.4.1.17713.11.6.86INTEGER (1..3)read-onlycurrent
ethernetStatisticsTable
OBJECT-TYPE
Instanced table showing the ethernet statistics
1.3.6.1.4.1.17713.11.6.87not-accessiblecurrent
ethernetStatisticsTableEntry
OBJECT-TYPE
Table EthernetStatisticsTable
1.3.6.1.4.1.17713.11.6.87.1not-accessiblecurrent
ethernetStatisticsTableIndex
OBJECT-TYPE
Used to index the ethernetStatisticsTable.
1.3.6.1.4.1.17713.11.6.87.1.1INTEGER (1..3)not-accessiblecurrent
ethernetStatisticsDataSource
OBJECT-TYPE
This object identifies the ethernet interface that this ethernetStatistics entry is configured to report. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in RFC 2233 [17], for the desired interface. For example, if an entry were to receive data from interface #1, this object would be set to ifIndex.1.
1.3.6.1.4.1.17713.11.6.87.1.2OBJECT IDENTIFIERread-onlycurrent
ethernetStatisticsRxOctets
OBJECT-TYPE
Total number of octets (excluding framing bits but including FCS octets) received from the LAN in good packets
1.3.6.1.4.1.17713.11.6.87.1.3Counter64read-onlycurrent
ethernetStatisticsRxFrames
OBJECT-TYPE
Total number of packets (including bad packets, broadcast packets, and multicast packets) received
1.3.6.1.4.1.17713.11.6.87.1.4Counter64read-onlycurrent
ethernetStatisticsRxBroadcasts
OBJECT-TYPE
Number of good and bad broadcast packets received from the LAN. Note that this does not include multicast packets.
1.3.6.1.4.1.17713.11.6.87.1.5Counter64read-onlycurrent
ethernetStatisticsRxFramesWithError
OBJECT-TYPE
Number of frames received with errors. The errors can be a frame check sequence (CRC) error, an alignment error or an incorrect frame length
1.3.6.1.4.1.17713.11.6.87.1.6Counter64read-onlycurrent
ethernetStatisticsRxFramesUndersize
OBJECT-TYPE
Number of short frames (<64 Bytes) received from the LAN with or without a valid CRC
1.3.6.1.4.1.17713.11.6.87.1.7Counter64read-onlycurrent
ethernetStatisticsRxFramesOversize
OBJECT-TYPE
Number of oversize frames received from the LAN with or without a valid CRC
1.3.6.1.4.1.17713.11.6.87.1.8Counter64read-onlycurrent
ethernetStatisticsTxOctets
OBJECT-TYPE
Total number of octets transmitted to the LAN
1.3.6.1.4.1.17713.11.6.87.1.9Counter64read-onlycurrent
ethernetStatisticsTxFrames
OBJECT-TYPE
Total number of frames transmitted to the LAN
1.3.6.1.4.1.17713.11.6.87.1.10Counter64read-onlycurrent
ethernetStatisticsTxBroadcasts
OBJECT-TYPE
Number of broadcast frames transmitted to the LAN. Note that this does not include multicast packets.
1.3.6.1.4.1.17713.11.6.87.1.11Counter64read-onlycurrent
tDM
OBJECT-IDENTITY
1.3.6.1.4.1.17713.11.7
tDMInterfaceControl
OBJECT-TYPE
The line interface type. If this is set to 'None' then the TDM interfaces are disabled, and the TDM settings will be ignored.
1.3.6.1.4.1.17713.11.7.1INTEGER {none(0), e1(1), t1(2)}read-onlycurrent
tDMInterfaceStatus
OBJECT-TYPE
@Current status of the connection to the TDM Box. A state of 'Up' on a green background indicates that the TDM Box is connected OK. When connecting a TDM Box only the Main Ethernet port should be used
1.3.6.1.4.1.17713.11.7.2INTEGER {ok(0), connectedNotConfigured(1), notConnected(2), nIDUdetectedonAUXport(3), error(4), codeDownloadInProgress(5)}read-onlycurrent
tDMEnabledChannels
OBJECT-TYPE
The number of TDM channels enabled in the system
1.3.6.1.4.1.17713.11.7.3INTEGER (0..8)read-onlycurrent
tdmTableNumber
OBJECT-TYPE
Number of entries in the TdmTable
1.3.6.1.4.1.17713.11.7.4INTEGER (1..8)read-onlycurrent
tdmTable
OBJECT-TYPE
A table storing a configuration and status for each TDM channel
1.3.6.1.4.1.17713.11.7.5not-accessiblecurrent
tdmTableEntry
OBJECT-TYPE
Table TdmTable
1.3.6.1.4.1.17713.11.7.5.1not-accessiblecurrent
tdmTableIndex
OBJECT-TYPE
TDM Channel flag, used to index channels in the TdmTable
1.3.6.1.4.1.17713.11.7.5.1.1INTEGER (1..8)not-accessiblecurrent
tDMChannelStatus
OBJECT-TYPE
Current status of the TDM channels. A value of 0 indicates that a TDM channel is established
1.3.6.1.4.1.17713.11.7.5.1.2INTEGER {up(0), noSignalLocal(1), noSignalRemote(2), noSignalLocalandRemote(3), remoteTiming(4), noSignalLocalandRemoteTiming(5), disabled(6)}read-onlycurrent
tDMChannelLineCode
OBJECT-TYPE
The line code setting of the TDM interfaces. This must match the setting of the device connected to an interface
1.3.6.1.4.1.17713.11.7.5.1.3INTEGER {aMI(0), b8ZSorHDB3(1)}read-onlycurrent
tDMChannelCableLength
OBJECT-TYPE
The lengths of the cables connected to the TDM interfaces, measured in feet
1.3.6.1.4.1.17713.11.7.5.1.4INTEGER {feet133(0), feet266(1), feet399(2), feet533(3), feet655(4)}read-onlycurrent
tDMChannelLoopback
OBJECT-TYPE
The loopback status of TDM channels. This is intended for installation testing and should be set to 'None' for normal operation. The wire connections to a unit can be tested by applying a 'Copper' loopback to the local unit. The wireless connection to the remote unit can be tested by applying a 'Wireless' loopback to the remote unit with no loopback on the local unit. NB: a change of state may generate an SNMP trap and/or SMTP email alert
1.3.6.1.4.1.17713.11.7.5.1.5INTEGER {none(0), copper(1), wireless(2)}read-onlycurrent
tDMConfigurationMismatch
OBJECT-TYPE
Current status of the configuration of the TDM Box. A state of 'Ok' on a green background indicates that the TDM Box configuration is matched OK with the remote end.
1.3.6.1.4.1.17713.11.7.6INTEGER {ok(0), linetypemismatch(1), enabledchannelsmismatch(2), linetypeandenabledchannelsmismatch(3)}read-onlycurrent
lowestTDMModulationMode
OBJECT-TYPE
The lowest modulation mode at which tdm data will be sent. The effective lowest modulation mode is displayed in the TDM Configuration page
1.3.6.1.4.1.17713.11.7.7INTEGER {modAcquisition(0), modBpsk63percent(1), modQpsk63percentSingle(2), modTransient1(3), modQpsk87percentSingle(4), modTransient2(5), mod16qam63percentSingleA(6), modTransient3(7), mod16qam87percentSingle(8), modTransient4(9), mod64qam75percentSingle(10), modTransient5(11), mod64qam92percentSingle(12), modTransient6(13), mod256qam81percentSingle(14), mod16qam63percentSingleB(15), mod16qam63percentDual(16), modTransient7(17), mod16qam87percentDual(18), modTransient8(19), mod64qam75percentDual(20), modTransient9(21), mod64qam92percentDual(22), modTransient10(23), mod256qam81percentDual(24)}read-onlycurrent
license
OBJECT-IDENTITY
1.3.6.1.4.1.17713.11.8
regulatoryBand
OBJECT-TYPE
The Regulatory Band prohibits the wireless unit from operating outside the regulated limits. An invalid Regulatory Band may be caused by a missing or incorrect License Key, a corrupt MAC Address or an attempt to configure a Regulatory Band not allowed by the License Key or an execution of Reset Configuration. NB: a change of state may generate an SNMP trap and/or SMTP email alert.
1.3.6.1.4.1.17713.11.8.1INTEGER {regInvalid(0), reg158GHz(1), reg258GHz(2), reg358GHz(3), reg458GHzWithRTTT(4), reg558GHz(5), reg658GHz(6), reg754GHz(7), reg854GHz(8), reg954GHz(9), reg1058GHz(10), reg1158GHz(11), reg1254GHz(12), reg1354GHz(13), reg1449GHzPublicSafety(14), reg15(15), reg1659GHz(16), reg1759GHz(17), reg1849GHzPublicSafety(18), reg1958GHz(19), reg2054GHz(20), reg2154GHz(21), reg2258GHz(22), reg23(23), reg2458GHz(24), reg2558GHz(25), reg2654GHz(26), reg2758GHz(27), reg2858GHz(28), reg2958GHz(29), reg3054GHz(30), reg3158GHz(31), reg3249GHzLicensed(32), reg3349GHzETSIBroadbandDisasterRelief(33), reg3458GHz(34), reg3558GHz(35), reg3654GHz(36), reg3758GHz(37), reg3852GHz(38), reg3951GHzETSIBroadbandDisasterRelief(39), reg4054GHz(40), reg4154GHz(41), reg4254GHz(42), reg4354GHz(43), reg4458GHz(44), reg4558GHz(45), reg4658GHz(46), reg4758GHz(47), reg4858GHz(48), reg4958GHz(49), reg5058GHz(50), reg5158GHz(51), reg5258GHz(52), reg5358GHz(53), reg5458GHz(54), reg5558GHz(55), reg5654GHz(56), reg5754GHz(57), reg5858GHz(58), reg5958GHz(59), reg6058GHz(60), reg6149GHz(61), reg6251GHz52GHz(62), reg6352GHz(63), reg6451GHz(64), reg6551GHz(65), reg6651GHz(66), reg6752GHz(67), reg6852GHz(68), reg6952GHz(69), reg7052GHz(70), reg7152GHz(71), reg7252GHz(72), reg7352GHz(73), reg7452GHz(74), reg7552GHz(75), reg7652GHz(76), reg7752GHz(77), reg7849GHz(78), reg7954GHz(79), reg8049GHz(80), reg8147GHz(81), reg8247GHz(82), reg8352GHz(83), reg8451GHz(84), reg8551GHz52GHz(85), reg8652GHz54GHz(86), reg8758GHz(87), reg8849GHz(88), reg8949GHz(89), reg9054GHzParabolicantenna(90), reg9152GHzParabolicantenna(91), reg9251GHzParabolicantenna(92), reg9349GHz(93), reg9449GHz(94), reg9545GHz(95), reg9648GHz(96), reg9752GHz(97), reg9849GHz27dBiantenna(98), reg9949GHz29dBiantenna(99), reg10048GHz(100), reg10158GHz(101), reg102(102), reg103(103), reg10458GHzNoRTTT(104), reg105(105), reg106(106), reg107(107), reg108(108), reg109(109), reg110(110), reg111(111), reg112(112), reg113(113), reg114(114), reg115(115), reg116(116), reg117(117), reg118(118), reg119(119), reg120(120), reg121(121), reg122(122), reg123(123), reg124(124), reg125(125), reg126(126), reg127(127), reg128(128), reg129(129), reg130(130), reg131(131), reg132(132), reg133(133), reg134(134), reg135(135), reg136(136), reg137(137), reg138(138), reg139(139), reg140(140), reg141(141), reg142(142), reg143(143), reg144(144), reg145(145), reg146(146), reg147(147), reg148(148), reg149(149), reg150(150), reg151(151), reg152(152), reg153(153), reg154(154), reg155(155), reg156(156), reg157(157), reg158(158), reg159(159), reg160(160), reg161(161), reg162(162), reg163(163), reg164(164), reg165(165), reg166(166), reg167(167), reg168(168), reg169(169), reg170(170), reg171(171), reg172(172), reg173(173), reg174(174), reg175(175), reg176(176), reg177(177), reg178(178), reg179(179), reg180(180), reg181(181), reg182(182), reg183(183), reg184(184), reg185(185), reg186(186), reg187(187), reg188(188), reg189(189), reg190(190), reg191(191), reg192(192), reg193(193), reg194(194), reg195(195), reg196(196), reg197(197), reg198(198), reg199(199), reg200(200), reg201(201), reg202(202), reg203(203), reg204(204), reg205(205), reg206(206), reg207(207), reg208(208), reg209(209), reg210(210), reg211(211), reg212(212), reg213(213), reg214(214), reg215(215), reg216(216), reg217(217), reg218(218), reg219(219), reg220(220), reg221(221), reg222(222), reg223(223), reg224(224), reg225(225), reg226(226), reg227(227), reg228(228), reg229(229), reg230(230), reg231(231), reg232(232), reg233(233), reg234(234), reg235(235), reg236(236), reg237(237), reg238(238), reg239(239), reg240(240), reg241(241), reg242(242), reg243(243), reg244(244), reg245(245), reg246(246), reg247(247), reg248(248), reg249(249), reg250(250), reg251(251), reg252(252), reg253(253), reg254(254), reg255(255)}read-onlycurrent
productVariant
OBJECT-TYPE
The product variant
1.3.6.1.4.1.17713.11.8.2INTEGER {pTPxx400Full(0), pTPxx400Deprecated1(1), pTPxx400Deprecated2(2), pTPxx400Lite(3), spare1(4), pTPxx300(5), spare2(6), spare3(7), pTPxx500FullDeprecated(8), pTPxx500LiteDeprecated(9), pTPxx500(10), pTPxx600Lite(11), pTPxx600Full(12), pTPxx650(13), pMP455(14), pTP800(15), pMPMedusa(16), pTPxx700(17), pTP50670(18), pTP50670ATEX(19), pTP48670(20)}read-onlycurrent
productName
OBJECT-TYPE
Name of the product variant
1.3.6.1.4.1.17713.11.8.3DisplayString (SIZE(0..63))read-onlycurrent
frequencyVariant
OBJECT-TYPE
The hardware frequency variant
1.3.6.1.4.1.17713.11.8.5INTEGER {freq50XXX(0), freq45XXX(1), freq48XXX(2)}read-onlycurrent
sNMPv3Enable
OBJECT-TYPE
SNMPv3 availability control
1.3.6.1.4.1.17713.11.8.9INTEGER {disabled(0), enabled(1)}read-onlycurrent
licenseVersion
OBJECT-TYPE
The license key version.
1.3.6.1.4.1.17713.11.8.12INTEGER (1)read-onlycurrent
licenseUnitSerialNumber
OBJECT-TYPE
The unit serial number.
1.3.6.1.4.1.17713.11.8.13DisplayString (SIZE(0..11))read-onlycurrent
licenseIssueNumber
OBJECT-TYPE
The license key issue number for this unit.
1.3.6.1.4.1.17713.11.8.15INTEGER (0..2147483647)read-onlycurrent
licenseCountry
OBJECT-TYPE
The country in which this unit is licensed to operate.
1.3.6.1.4.1.17713.11.8.16DisplayString (SIZE(0..103))read-onlycurrent
licenseNumberOfRegulatoryBands
OBJECT-TYPE
The number of regulatory bands for which the unit is licensed to operate.
1.3.6.1.4.1.17713.11.8.17INTEGER (0..32)read-onlycurrent
licenseRegulatoryBandsTable
OBJECT-TYPE
1.3.6.1.4.1.17713.11.8.18not-accessiblecurrent
licenseRegulatoryBandsTableEntry
OBJECT-TYPE
Table LicenseRegulatoryBandsTable
1.3.6.1.4.1.17713.11.8.18.1not-accessiblecurrent
licenseRegulatoryBandsTableIndex
OBJECT-TYPE
License regulatory bands, used to index the LicenseRegulatoryBandsTable.
1.3.6.1.4.1.17713.11.8.18.1.1INTEGER (1..32)not-accessiblecurrent
licenseRegulatoryBandsList
OBJECT-TYPE
The list of regulatory bands for which the unit is licensed to operate. A regulatory band prohibits the wireless unit from operating outside the regulated limits. An invalid regulatory band indicates a corrupted license key. NB: a change of state may generate an SNMP trap and/or SMTP email alert.
1.3.6.1.4.1.17713.11.8.18.1.2INTEGER {regInvalid(0), reg158GHz(1), reg258GHz(2), reg358GHz(3), reg458GHzWithRTTT(4), reg558GHz(5), reg658GHz(6), reg754GHz(7), reg854GHz(8), reg954GHz(9), reg1058GHz(10), reg1158GHz(11), reg1254GHz(12), reg1354GHz(13), reg1449GHzPublicSafety(14), reg15(15), reg1659GHz(16), reg1759GHz(17), reg1849GHzPublicSafety(18), reg1958GHz(19), reg2054GHz(20), reg2154GHz(21), reg2258GHz(22), reg23(23), reg2458GHz(24), reg2558GHz(25), reg2654GHz(26), reg2758GHz(27), reg2858GHz(28), reg2958GHz(29), reg3054GHz(30), reg3158GHz(31), reg3249GHzLicensed(32), reg3349GHzETSIBroadbandDisasterRelief(33), reg3458GHz(34), reg3558GHz(35), reg3654GHz(36), reg3758GHz(37), reg3852GHz(38), reg3951GHzETSIBroadbandDisasterRelief(39), reg4054GHz(40), reg4154GHz(41), reg4254GHz(42), reg4354GHz(43), reg4458GHz(44), reg4558GHz(45), reg4658GHz(46), reg4758GHz(47), reg4858GHz(48), reg4958GHz(49), reg5058GHz(50), reg5158GHz(51), reg5258GHz(52), reg5358GHz(53), reg5458GHz(54), reg5558GHz(55), reg5654GHz(56), reg5754GHz(57), reg5858GHz(58), reg5958GHz(59), reg6058GHz(60), reg6149GHz(61), reg6251GHz52GHz(62), reg6352GHz(63), reg6451GHz(64), reg6551GHz(65), reg6651GHz(66), reg6752GHz(67), reg6852GHz(68), reg6952GHz(69), reg7052GHz(70), reg7152GHz(71), reg7252GHz(72), reg7352GHz(73), reg7452GHz(74), reg7552GHz(75), reg7652GHz(76), reg7752GHz(77), reg7849GHz(78), reg7954GHz(79), reg8049GHz(80), reg8147GHz(81), reg8247GHz(82), reg8352GHz(83), reg8451GHz(84), reg8551GHz52GHz(85), reg8652GHz54GHz(86), reg8758GHz(87), reg8849GHz(88), reg8949GHz(89), reg9054GHzParabolicantenna(90), reg9152GHzParabolicantenna(91), reg9251GHzParabolicantenna(92), reg9349GHz(93), reg9449GHz(94), reg9545GHz(95), reg9648GHz(96), reg9752GHz(97), reg9849GHz27dBiantenna(98), reg9949GHz29dBiantenna(99), reg10048GHz(100), reg10158GHz(101), reg102(102), reg103(103), reg10458GHzNoRTTT(104), reg105(105), reg106(106), reg107(107), reg108(108), reg109(109), reg110(110), reg111(111), reg112(112), reg113(113), reg114(114), reg115(115), reg116(116), reg117(117), reg118(118), reg119(119), reg120(120), reg121(121), reg122(122), reg123(123), reg124(124), reg125(125), reg126(126), reg127(127), reg128(128), reg129(129), reg130(130), reg131(131), reg132(132), reg133(133), reg134(134), reg135(135), reg136(136), reg137(137), reg138(138), reg139(139), reg140(140), reg141(141), reg142(142), reg143(143), reg144(144), reg145(145), reg146(146), reg147(147), reg148(148), reg149(149), reg150(150), reg151(151), reg152(152), reg153(153), reg154(154), reg155(155), reg156(156), reg157(157), reg158(158), reg159(159), reg160(160), reg161(161), reg162(162), reg163(163), reg164(164), reg165(165), reg166(166), reg167(167), reg168(168), reg169(169), reg170(170), reg171(171), reg172(172), reg173(173), reg174(174), reg175(175), reg176(176), reg177(177), reg178(178), reg179(179), reg180(180), reg181(181), reg182(182), reg183(183), reg184(184), reg185(185), reg186(186), reg187(187), reg188(188), reg189(189), reg190(190), reg191(191), reg192(192), reg193(193), reg194(194), reg195(195), reg196(196), reg197(197), reg198(198), reg199(199), reg200(200), reg201(201), reg202(202), reg203(203), reg204(204), reg205(205), reg206(206), reg207(207), reg208(208), reg209(209), reg210(210), reg211(211), reg212(212), reg213(213), reg214(214), reg215(215), reg216(216), reg217(217), reg218(218), reg219(219), reg220(220), reg221(221), reg222(222), reg223(223), reg224(224), reg225(225), reg226(226), reg227(227), reg228(228), reg229(229), reg230(230), reg231(231), reg232(232), reg233(233), reg234(234), reg235(235), reg236(236), reg237(237), reg238(238), reg239(239), reg240(240), reg241(241), reg242(242), reg243(243), reg244(244), reg245(245), reg246(246), reg247(247), reg248(248), reg249(249), reg250(250), reg251(251), reg252(252), reg253(253), reg254(254), reg255(255)}read-onlycurrent
licenseBandwidthCap
OBJECT-TYPE
The wireless link bandwidth cap in MHz. Zero indicates no bandwidth cap.
1.3.6.1.4.1.17713.11.8.20INTEGER (0..2147483647)read-onlycurrent
licenseEncryption
OBJECT-TYPE
The license key encryption algorithms available.
1.3.6.1.4.1.17713.11.8.21INTEGER {none(0), aES128bit(1), aES192bit(2), aES256bit(3)}read-onlycurrent
licenseSecurityLevel
OBJECT-TYPE
The license key security level.
1.3.6.1.4.1.17713.11.8.22INTEGER {normal(0), fIPS(1), uCAPL(2)}read-onlycurrent
licenseGroupAccess
OBJECT-TYPE
The license key group access setting. Note that for HCMP topology, license group access must be enabled.
1.3.6.1.4.1.17713.11.8.23INTEGER {disabled(0), enabled(1)}read-onlycurrent
licenseOOBManagementSupport
OBJECT-TYPE
The license key Out-Of-Band (OOB) support setting.
1.3.6.1.4.1.17713.11.8.24INTEGER {disabled(0), enabled(1)}read-onlycurrent
licenseSFPPortSupport
OBJECT-TYPE
The license key Ethernet SFP Port support setting.
1.3.6.1.4.1.17713.11.8.25INTEGER {disabled(0), enabled(1)}read-onlycurrent
licenseAuxiliaryPortSupport
OBJECT-TYPE
The license key Ethernet Auxiliary Port support setting.
1.3.6.1.4.1.17713.11.8.26INTEGER {disabled(0), enabled(1)}read-onlycurrent
licenseCapacity
OBJECT-TYPE
The license key capacity. Note that for HCMP topology, license capacity must be full.
1.3.6.1.4.1.17713.11.8.27INTEGER {full(0), mid(1), lite(2)}read-onlycurrent
licenseMaxNumberOfTDMChannels
OBJECT-TYPE
The license key maximum TDM channels setting. Zero indicates TDM not available.
1.3.6.1.4.1.17713.11.8.28INTEGER (0..8)read-onlycurrent
licenseIEEE1588Support
OBJECT-TYPE
The license key IEEE-1588 support setting.
1.3.6.1.4.1.17713.11.8.29INTEGER {disabled(0), enabled(1)}read-onlycurrent
licenseSyncESupport
OBJECT-TYPE
The license key SyncE support setting.
1.3.6.1.4.1.17713.11.8.30INTEGER {disabled(0), enabled(1)}read-onlycurrent
licenseIPv6Support
OBJECT-TYPE
The license key IPv6 support setting.
1.3.6.1.4.1.17713.11.8.31INTEGER {disabled(0), enabled(1)}read-onlycurrent
licenseMinimumFirmwareVersion
OBJECT-TYPE
The minimum firmware version required to support this license key.
1.3.6.1.4.1.17713.11.8.32DisplayString (SIZE(0..23))read-onlycurrent
licenseFullCapabilityTrialStatus
OBJECT-TYPE
The license key full capability trial period status.
1.3.6.1.4.1.17713.11.8.33INTEGER {available(0), active(1), inactive(2), expired(3), unavailable(4)}read-onlycurrent
licenseRemainingTrialPeriod
OBJECT-TYPE
The remaining time for the license key full capability trial period.
1.3.6.1.4.1.17713.11.8.34INTEGER (0..31536000)read-onlycurrent
licenseRemainingTrialPeriodAlarm
OBJECT-TYPE
If the full capability trial license period is about to expire then purchase a license upgrade from your reseller.
1.3.6.1.4.1.17713.11.8.35INTEGER {fullCapabilityTrialNotActiveOrMoreThan7DaysRemaining(0), fullCapabilityTrialExpiringInLessThan7Days(1), fullCapabilityTrialExpiringInLessThan6Days(2), fullCapabilityTrialExpiringInLessThan5Days(3), fullCapabilityTrialExpiringInLessThan4Days(4), fullCapabilityTrialExpiringInLessThan3Days(5), fullCapabilityTrialExpiringInLessThan2Days(6), fullCapabilityTrialExpiringInLessThan1Day(7), fullCapabilityTrialHasExpired(8)}read-onlycurrent
capacityVariantMismatchLinked
OBJECT-TYPE
The remote node of this link has a lower link capacity. Operating with a reduced effective link capacity.
1.3.6.1.4.1.17713.11.8.36INTEGER {noError(0), mismatchDetected(1)}read-onlycurrent
licenseTDDSyncSupport
OBJECT-TYPE
The license key TDD Synchronization support setting.
1.3.6.1.4.1.17713.11.8.37INTEGER {disabled(0), enabled(1)}read-onlycurrent
licenseMaxLinkRange
OBJECT-TYPE
Maximum licensed range for the wireless link in tenths of km. A value of zero indicates that the maximum link range is not limited by the license.
1.3.6.1.4.1.17713.11.8.38INTEGER (0..2499)read-onlycurrent
licenseTrialPeriod
OBJECT-TYPE
The license key maximum trial period, in days.
1.3.6.1.4.1.17713.11.8.39INTEGER (0..365)read-onlycurrent
licenseRARSupport
OBJECT-TYPE
The license key Radio Aware Routing support setting.
1.3.6.1.4.1.17713.11.8.40INTEGER {disabled(0), mAB(1), dLEP(2), mABandDLEP(3)}read-onlycurrent
licenseGasGroup
OBJECT-TYPE
The HAZLOC/ATEX Configuration of this unit. The Gas Group is configured by the license key.
1.3.6.1.4.1.17713.11.8.41INTEGER {nonHAZLOCUnit(0), gasGroupA(1), gasGroupB(2), gasGroupC(3), gasGroupD(4)}read-onlycurrent
licenseLongMinimumFirmwareVersion
OBJECT-TYPE
The minimum long firmware version required to support this license key.
1.3.6.1.4.1.17713.11.8.42DisplayString (SIZE(0..15))read-onlycurrent
licenseHCMPSupport
OBJECT-TYPE
The license High Capacity MultiPoint support setting
1.3.6.1.4.1.17713.11.8.43INTEGER {disabled(0), slaveEnabled(1), masterEnabled(2), masterandSlaveEnabled(3)}read-onlycurrent
licenseInstancedTableNumber
OBJECT-TYPE
Number of entries in the licenseInstancedTable.
1.3.6.1.4.1.17713.11.8.44INTEGER (1..8)read-onlycurrent
licenseInstancedTable
OBJECT-TYPE
Instanced license table
1.3.6.1.4.1.17713.11.8.45not-accessiblecurrent
licenseInstancedTableEntry
OBJECT-TYPE
Table LicenseInstancedTable
1.3.6.1.4.1.17713.11.8.45.1not-accessiblecurrent
licenseInstancedTableIndex
OBJECT-TYPE
Used to index the LicenseInstancedTable.
1.3.6.1.4.1.17713.11.8.45.1.1INTEGER (1..8)not-accessiblecurrent
capacityVariantMismatch
OBJECT-TYPE
The remote node of this link has a lower link capacity. Operating with a reduced effective link capacity.
1.3.6.1.4.1.17713.11.8.45.1.2INTEGER {noError(0), mismatchDetected(1)}read-onlycurrent
licenseTLSRekey
OBJECT-TYPE
The license TLS Rekey support setting
1.3.6.1.4.1.17713.11.8.46INTEGER {disabled(0), enabled(1)}read-onlycurrent
licenseAdvanceHCMPSupport
OBJECT-TYPE
The license Advance High Capacity MultiPoint support setting
1.3.6.1.4.1.17713.11.8.47INTEGER {disabled(0), slaveEnabled(1), masterEnabled(2), masterandSlaveEnabled(3)}read-onlycurrent
licenseMinFirmwareVersionPTP650Emulation
OBJECT-TYPE
The minimum long firmware version of 650-Emulation required to support this license key.
1.3.6.1.4.1.17713.11.8.48DisplayString (SIZE(0..15))read-onlycurrent
management
OBJECT-IDENTITY
1.3.6.1.4.1.17713.11.9
targetRange
OBJECT-TYPE
Initial target range used in installation +/-1, expressed in tenths of a kilometer. When Auto-Ranging this must be set to 0
1.3.6.1.4.1.17713.11.9.1INTEGER (0..2500)read-onlycurrent
rangingMode
OBJECT-TYPE
Type of ranging to use during installation, either Auto-Ranging or use a selectable Target Range
1.3.6.1.4.1.17713.11.9.2INTEGER {auto0to40km(0), auto0to100km(1), auto0to200km(2), auto0to250km(3), targetRange(4)}read-onlycurrent
installStatusLinked
OBJECT-TYPE
A non-zero value indicates that signalling was received with the wrong MAC address or a mismatched link name. NB: It is very unusual to detect this, because units with mis-configured Target MAC Address will normally fail to establish a wireless link. However, rare circumstances may establish a partial wireless link and detect this situation. NB: A non-zero value on start-up, or a change of value during operation, may generate an SNMP trap and/or SMTP email alert
1.3.6.1.4.1.17713.11.9.3INTEGER {ok(0), wrongPeer(1)}read-onlycurrent
installArmState
OBJECT-TYPE
Indicates if the unit is being installed. NB: a change of state may generate an SNMP trap and/or SMTP email alert
1.3.6.1.4.1.17713.11.9.4INTEGER {disarmed(0), armed(1)}read-writecurrent
tFTPServerPortNumber
OBJECT-TYPE
The port number of the TFTP Server from which the TFTP Software Upgrade File Name will be retrieved
1.3.6.1.4.1.17713.11.9.6INTEGER (0..65535)read-writecurrent
tFTPSoftwareUpgradeFileName
OBJECT-TYPE
Filename of the Software Upgrade to be loaded from the TFTP Server
1.3.6.1.4.1.17713.11.9.7DisplayString (SIZE(0..127))read-writecurrent
tFTPStartSoftwareUpgrade
OBJECT-TYPE
Write '1' to this attribute to start the TFTP software upgrade process. The attribute will be reset to 0 when the upgrade process has finished. Continuing with the software upgrade will cause spectrum management (DSO) channel metrics collection to stop. The wireless unit will no longer search for the optimal operational radio channel. The performance of this wireless link may deterioate over time. If operating in a regulatory band where RADAR detection is mandatory you must complete the software upgrade and reboot the unit. Channel metrics collection will only be restarted after the wireless unit has been rebooted
1.3.6.1.4.1.17713.11.9.8Integer32read-writecurrent
tFTPSoftwareUpgradeStatus
OBJECT-TYPE
The current status of the TFTP Software upgrade process
1.3.6.1.4.1.17713.11.9.9INTEGER {idle(0), uploadinprogress(1), uploadsuccessfulprogrammingFLASH(2), upgradesuccessfulreboottorunthenewsoftwareimage(3), upgradefailed(4), upgradewarning(5)}read-onlycurrent
tFTPSoftwareUpgradeStatusText
OBJECT-TYPE
Descriptive text describing the status of the TFTP Software upgrade process, including any error details
1.3.6.1.4.1.17713.11.9.10DisplayString (SIZE(0..127))read-onlycurrent
tFTPSoftwareUpgradeStatusAdditionalText
OBJECT-TYPE
Any additional text describing the status of the TFTP Software upgrade process, including any error details
1.3.6.1.4.1.17713.11.9.11DisplayString (SIZE(0..127))read-onlycurrent
hTTPAccessEnabled
OBJECT-TYPE
This controls whether or not HTTP access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the HTTP port. Remote management via HTTPS is not affected by this setting. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = Enabled)
1.3.6.1.4.1.17713.11.9.12INTEGER {no(0), yes(1)}read-writecurrent
telnetAccessEnabled
OBJECT-TYPE
This controls whether or not Telnet access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the TELNET port. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = Disabled)
1.3.6.1.4.1.17713.11.9.13INTEGER {no(0), yes(1)}read-writecurrent
hTTPPortNumber
OBJECT-TYPE
This controls the port number for HTTP access. A value of zero will use the default port number. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = 80)
1.3.6.1.4.1.17713.11.9.14INTEGER (0..65535)read-writecurrent
hTTPSPortNumber
OBJECT-TYPE
This controls the port number for HTTPS access. A value of zero will use the default port number. Availability of HTTPS is controlled via the License Key. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = 443)
1.3.6.1.4.1.17713.11.9.15INTEGER (0..65535)read-writecurrent
telnetPortNumber
OBJECT-TYPE
This controls the port number for TELNET access. A value of zero will use the default port number. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = 23)
1.3.6.1.4.1.17713.11.9.16INTEGER (0..65535)read-writecurrent
hTTPSAccessEnabled
OBJECT-TYPE
This controls whether or not HTTPS access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the HTTPS port. Remote management via HTTP is not affected by this setting. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = Disabled)
1.3.6.1.4.1.17713.11.9.17INTEGER {no(0), yes(1)}read-writecurrent
tFTPServerInternetAddressType
OBJECT-TYPE
The type of Internet address specified by the associated tFTPServerInternetAddress.
1.3.6.1.4.1.17713.11.9.18INTEGER {unknown(0), ipv4(1), ipv6(2), ipv4z(3), ipv6z(4), unknown6(5), unknown7(6), unknown8(7), unknown9(8), unknown10(9), unknown11(10), unknown12(11), unknown13(12), unknown14(13), unknown15(14), unknown16(15), dns(16)}read-onlycurrent
tFTPServerInternetAddress
OBJECT-TYPE
INET address of the TFTP Server from which the TFTP Software Upgrade File Name will be retrieved
1.3.6.1.4.1.17713.11.9.19InetAddressread-writecurrent
lowestDataModulationMode
OBJECT-TYPE
The lowest modulation mode at which Ethernet Data traffic will be bridged over the wireless link
1.3.6.1.4.1.17713.11.9.20INTEGER {modAcquisition(0), modBpsk63percent(1), modQpsk63percentSingle(2), modTransient1(3), modQpsk87percentSingle(4), modTransient2(5), mod16qam63percentSingleA(6), modTransient3(7), mod16qam87percentSingle(8), modTransient4(9), mod64qam75percentSingle(10), modTransient5(11), mod64qam92percentSingle(12), modTransient6(13), mod256qam81percentSingle(14), mod16qam63percentSingleB(15), mod16qam63percentDual(16), modTransient7(17), mod16qam87percentDual(18), modTransient8(19), mod64qam75percentDual(20), modTransient9(21), mod64qam92percentDual(22), modTransient10(23), mod256qam81percentDual(24)}read-onlycurrent
tFTPClient
OBJECT-TYPE
This controls whether or not TFTP client is enabled, i.e. if this is disabled (0) then the unit will not respond to any TFTP software download requests. (Factory default = Enabled)
1.3.6.1.4.1.17713.11.9.22INTEGER {disabled(0), enabled(1)}read-onlycurrent
mgmtInstancedTableNumber
OBJECT-TYPE
Number of entries in the mgmtInstancedTable.
1.3.6.1.4.1.17713.11.9.23INTEGER (1..8)read-onlycurrent
mgmtInstancedTable
OBJECT-TYPE
Instanced management table.
1.3.6.1.4.1.17713.11.9.24not-accessiblecurrent
mgmtInstancedTableEntry
OBJECT-TYPE
Table MgmtInstancedTable
1.3.6.1.4.1.17713.11.9.24.1not-accessiblecurrent
mgmtInstancedTableIndex
OBJECT-TYPE
Used to index values in the mgmtInstancedTable
1.3.6.1.4.1.17713.11.9.24.1.1INTEGER (1..8)not-accessiblecurrent
installStatus
OBJECT-TYPE
A non-zero value indicates that signalling was received with the wrong MAC address or a mismatched link name. NB: It is very unusual to detect this, because units with mis-configured Target MAC Address will normally fail to establish a wireless link. However, rare circumstances may establish a partial wireless link and detect this situation. NB: A non-zero value on start-up, or a change of value during operation, may generate an SNMP trap and/or SMTP email alert
1.3.6.1.4.1.17713.11.9.24.1.2INTEGER {ok(0), wrongPeer(1)}read-onlycurrent
tFTPServerResolvedInternetAddress
OBJECT-TYPE
IP Address of the TFTP Server.
1.3.6.1.4.1.17713.11.9.25DisplayString (SIZE(0..63))read-onlycurrent
installationMode
OBJECT-TYPE
Determines whether the unit is armed for antenna alignment, and whether it emits audible installation tones to indicate the state and strength of the received signal. Alternatively, configuration changes may be made without arming the unit (typically once a link has already been established). Note: while armed, a unit will have reduced link performance and functionality.
1.3.6.1.4.1.17713.11.9.26INTEGER {armWithTones(0), armWithoutTones(1), changeConfigWithoutArming(2)}read-writecurrent
phyControl
OBJECT-IDENTITY
1.3.6.1.4.1.17713.11.10
linkSymmetry
OBJECT-TYPE
Provides configuration options for sharing the available wireless capacity between the transmit and receive directions. Fixed link symmetry is defined by a ratio of the burst duration for the transmit direction to the burst duration for the receive direction. Permitted settings are 5:1, 3:1, 2:1, 1:1, 1:2, 1:3, 1:5. The 1:1 option provides fixed symmetric operation. The adaptive option selects transmit and receive burst durations automatically in response to the offered Ethernet traffic in each link direction. This attribute is valid only for a unit configured as a TDD Master
1.3.6.1.4.1.17713.11.10.1INTEGER {symmetryAdaptive(0), symmetry2to1(1), symmetry1to1(2), symmetry1to2(3), symmetry3to1(4), symmetry1to3(5), symmetry5to1(6), symmetry1to5(7)}read-onlycurrent
userConfiguredMaxModulationMode
OBJECT-TYPE
The maximum receive modulation mode controls the MAX mode used for adaptive modulation. NOTE: This attribute is automatically disabled when the installation agent is armed. To disarm the installation agent use the installation wizard
1.3.6.1.4.1.17713.11.10.2INTEGER {modBpsk63percent(0), modQpsk63percent(1), modQpsk87percent(2), mod16qam63percent(3), mod16qam87percent(4), mod64qam75percent(5), mod64qam92percent(6), mod256qam81percent(7)}read-writecurrent
linkModeOptimization
OBJECT-TYPE
Optimizes the wireless link behavior for the type of traffic to be carried. In 'IP Traffic' mode, the wireless link will minimize transmission errors by automatically adapting the modulation mode. In 'TDM Traffic' mode, the wireless link will minimize transmission latency and preserve throughput by maintaining a higher modulation mode in the presence of a limited number of errors. The 'TDM Traffic' mode is recommended for E1/T1 applications and connectionless protocols.
1.3.6.1.4.1.17713.11.10.3INTEGER {iPTraffic(0), tDMTraffic(1)}read-onlycurrent
txColorCode
OBJECT-TYPE
Transmit Color Code. This attribute need only be considered when the unit is installed in a network of wireless units and where some of the units are operating on the same frequency. In this case, the value would normally be derived by a network planner. In all other cases, it is recommended that this attribute is left at the default value. NOTE: For the link to operate, the value of this parameter must in all cases match the value of the Rx Color Code parameter at the far end of the link.
1.3.6.1.4.1.17713.11.10.4INTEGER {a(0), b(1), c(2), d(3), e(4)}read-onlycurrent
rxColorCode
OBJECT-TYPE
Receive Color Code. This attribute need only be considered when the unit is installed in a network of wireless units and where some of the units are operating on the same frequency. In this case, the value would normally be derived by a network planner. In all other cases, it is recommended that this attribute is left at the default value. NOTE: For the link to operate, the value of this parameter must in all cases match the value of the Tx Color Code parameter at the far end of the link.
1.3.6.1.4.1.17713.11.10.5INTEGER {a(0), b(1), c(2), d(3), e(4)}read-onlycurrent
remoteMaximumTransmitPowerLinked
OBJECT-TYPE
Maximum transmit power the remote wireless unit is permitted to use when establishing and maintaining the wireless link
1.3.6.1.4.1.17713.11.10.6INTEGER (-15..30)read-onlycurrent
phyControlInstancedTableNumber
OBJECT-TYPE
Number of entries in the PhyControlInstancedTable.
1.3.6.1.4.1.17713.11.10.7INTEGER (1..8)read-onlycurrent
phyControlInstancedTable
OBJECT-TYPE
1.3.6.1.4.1.17713.11.10.8not-accessiblecurrent
phyControlInstancedTableEntry
OBJECT-TYPE
Table PhyControlInstancedTable
1.3.6.1.4.1.17713.11.10.8.1not-accessiblecurrent
phyControlInstancedTableIndex
OBJECT-TYPE
Used to index the PhyControlInstancedTable.
1.3.6.1.4.1.17713.11.10.8.1.1INTEGER (1..8)not-accessiblecurrent
remoteMaximumTransmitPower
OBJECT-TYPE
Maximum transmit power the remote wireless unit is permitted to use when establishing and maintaining the wireless link
1.3.6.1.4.1.17713.11.10.8.1.2INTEGER (-15..30)read-onlycurrent
phyStatus
OBJECT-IDENTITY
1.3.6.1.4.1.17713.11.12
linkLossLinked
OBJECT-TYPE
The wireless link loss expressed in tenths of a dB
1.3.6.1.4.1.17713.11.12.1INTEGER (-500..500)read-onlycurrent
receivePowerLinked
OBJECT-TYPE
Receive power expressed in tenths of a dBm
1.3.6.1.4.1.17713.11.12.2Integer32read-onlycurrent
vectorErrorLinked
OBJECT-TYPE
The vector error measurement compares the received signal's IQ modulation characteristics to an ideal signal to determine the composite error vector magnitude. The value represented by this attribute is the average vector error over the previous second expressed in tenths of a dB
1.3.6.1.4.1.17713.11.12.3Integer32read-onlycurrent
transmitPowerLinked
OBJECT-TYPE
Transmit power expressed in tenths of a dBm
1.3.6.1.4.1.17713.11.12.4Integer32read-onlycurrent
receiveChannel
OBJECT-TYPE
Current active receive channel
1.3.6.1.4.1.17713.11.12.5INTEGER (0..305)read-onlycurrent
transmitChannel
OBJECT-TYPE
Current active transmit channel
1.3.6.1.4.1.17713.11.12.6INTEGER (0..305)read-onlycurrent
receiveFreqMHz
OBJECT-TYPE
Current receive frequency expressed in integer MHz
1.3.6.1.4.1.17713.11.12.7INTEGER (0..6050)read-onlycurrent
transmitFreqMHz
OBJECT-TYPE
Current transmit frequency expressed in integer MHz
1.3.6.1.4.1.17713.11.12.8INTEGER (0..6050)read-onlycurrent
signalStrengthRatioLinked
OBJECT-TYPE
Signal strength ratio (Vertical / Horizontal) : the number of dB larger the Vertical antenna input is than the Horizontal antenna input expressed in tenths of a dB
1.3.6.1.4.1.17713.11.12.9Integer32read-onlycurrent
receiveFreqKHz
OBJECT-TYPE
Current receive frequency expressed as KHz
1.3.6.1.4.1.17713.11.12.10INTEGER (0..6050000)read-onlycurrent
transmitFreqKHz
OBJECT-TYPE
Current transmit frequency expressed as KHz
1.3.6.1.4.1.17713.11.12.11INTEGER (0..6050000)read-onlycurrent
rawReceivePowerLinked
OBJECT-TYPE
Raw receive power expressed in tenths of a dBm
1.3.6.1.4.1.17713.11.12.12Integer32read-onlycurrent
rangeLinked
OBJECT-TYPE
Distance between the two peer wireless units expressed in tenths of a kilometer
1.3.6.1.4.1.17713.11.12.13Integer32read-onlycurrent
receiveModulationModeLinked
OBJECT-TYPE
Current active receive modulation mode
1.3.6.1.4.1.17713.11.12.14INTEGER (0..28)read-onlycurrent
transmitModulationModeLinked
OBJECT-TYPE
Current active transmit modulation mode
1.3.6.1.4.1.17713.11.12.15INTEGER (0..28)read-onlycurrent
searchStateLinked
OBJECT-TYPE
Search status of the wireless modem. 'Registering' means that the modem has locked to an OFDM signal, and the wireless link is up. 'Searching' means that no wireless signal has been detected. 'Acquiring' means that a wireless signal has been detected, but the modem has not locked to an OFDM signal.
1.3.6.1.4.1.17713.11.12.16INTEGER {registering(0), searching(1), acquiring(2)}read-onlycurrent
remoteMACAddressLinked
OBJECT-TYPE
MAC Address of the peer wireless unit
1.3.6.1.4.1.17713.11.12.17OCTET STRING (SIZE(6))read-onlycurrent
phyInstancedStatusTableNumber
OBJECT-TYPE
Number of entries in the phyInstancedStatusTable.
1.3.6.1.4.1.17713.11.12.18INTEGER (1..8)read-onlycurrent
phyInstancedStatusTable
OBJECT-TYPE
Instanced PHY status table.
1.3.6.1.4.1.17713.11.12.19not-accessiblecurrent
phyInstancedStatusTableEntry
OBJECT-TYPE
Table PhyInstancedStatusTable
1.3.6.1.4.1.17713.11.12.19.1not-accessiblecurrent
phyInstancedStatusTableIndex
OBJECT-TYPE
Used to index the phyInstancedStatusTable.
1.3.6.1.4.1.17713.11.12.19.1.1INTEGER (1..8)not-accessiblecurrent
linkLoss
OBJECT-TYPE
The link loss measurement = Peer Tx_Power(dBm) - Local Rx_Power(dBm) + 2 x Antenna_Pattern(dBi)
1.3.6.1.4.1.17713.11.12.19.1.2INTEGER (-500..500)read-onlycurrent
receivePower
OBJECT-TYPE
Receive power histogram
1.3.6.1.4.1.17713.11.12.19.1.3Integer32read-onlycurrent
vectorError
OBJECT-TYPE
The vector error measurement compares the received signal's IQ modulation characteristics to an ideal signal to determine the composite error vector magnitude
1.3.6.1.4.1.17713.11.12.19.1.4Integer32read-onlycurrent
signalStrengthRatio
OBJECT-TYPE
Signal strength ratio (Vertical / Horizontal) : the number of dB larger the Vertical antenna input is than the Horizontal antenna input
1.3.6.1.4.1.17713.11.12.19.1.5Integer32read-onlycurrent
range
OBJECT-TYPE
Distance between the two peer wireless units
1.3.6.1.4.1.17713.11.12.19.1.6Integer32read-onlycurrent
receiveModulationMode
OBJECT-TYPE
Current active receive modulation mode
1.3.6.1.4.1.17713.11.12.19.1.7INTEGER {modAcquisition(0), modBpsk63percent(1), modQpsk63percentSingle(2), modTransient1(3), modQpsk87percentSingle(4), modTransient2(5), mod16qam63percentSingleA(6), modTransient3(7), mod16qam87percentSingle(8), modTransient4(9), mod64qam75percentSingle(10), modTransient5(11), mod64qam92percentSingle(12), modTransient6(13), mod256qam81percentSingle(14), mod16qam63percentSingleB(15), mod16qam63percentDual(16), modTransient7(17), mod16qam87percentDual(18), modTransient8(19), mod64qam75percentDual(20), modTransient9(21), mod64qam92percentDual(22), modTransient10(23), mod256qam81percentDual(24)}read-onlycurrent
transmitModulationMode
OBJECT-TYPE
Current active transmit modulation mode
1.3.6.1.4.1.17713.11.12.19.1.8INTEGER {modAcquisition(0), modBpsk63percent(1), modQpsk63percentSingle(2), modTransient1(3), modQpsk87percentSingle(4), modTransient2(5), mod16qam63percentSingleA(6), modTransient3(7), mod16qam87percentSingle(8), modTransient4(9), mod64qam75percentSingle(10), modTransient5(11), mod64qam92percentSingle(12), modTransient6(13), mod256qam81percentSingle(14), mod16qam63percentSingleB(15), mod16qam63percentDual(16), modTransient7(17), mod16qam87percentDual(18), modTransient8(19), mod64qam75percentDual(20), modTransient9(21), mod64qam92percentDual(22), modTransient10(23), mod256qam81percentDual(24)}read-onlycurrent
searchState
OBJECT-TYPE
Search status of the wireless modem. 'Registering' means that the modem has locked to an OFDM signal, and the wireless link is up. 'Searching' means that no wireless signal has been detected. 'Acquiring' means that a wireless signal has been detected, but the modem has not locked to an OFDM signal.
1.3.6.1.4.1.17713.11.12.19.1.9INTEGER {registering(0), searching(1), acquiring(2)}read-onlycurrent
remoteMACAddress
OBJECT-TYPE
MAC Address of the peer wireless unit
1.3.6.1.4.1.17713.11.12.19.1.10OCTET STRING (SIZE(6))read-onlycurrent
rawReceivePower
OBJECT-TYPE
Raw receive power
1.3.6.1.4.1.17713.11.12.19.1.11Integer32read-onlycurrent
transmitPower
OBJECT-TYPE
Transmit power histogram
1.3.6.1.4.1.17713.11.12.19.1.12Integer32read-onlycurrent
tempPcb
OBJECT-TYPE
PCB temperature expressed in Celsius
1.3.6.1.4.1.17713.11.12.20INTEGER (-100..200)read-onlycurrent
alarms
OBJECT-IDENTITY
1.3.6.1.4.1.17713.11.13
unitOutOfCalibration
OBJECT-TYPE
The unit is out of calibration
1.3.6.1.4.1.17713.11.13.1INTEGER {calibrated(0), partialCalibration(1), invalidCalibration(2), bandwidthvariantunsupportedPAsShutdown(3), outOfCalibrationPAsShutdown(4)}read-onlycurrent
incompatibleRegulatoryBandsLinked
OBJECT-TYPE
The master and slave units have incompatible regulatory bands. NB: Both units must have compatible license keys
1.3.6.1.4.1.17713.11.13.4INTEGER {regOK(0), regIncompatibleLicenseKeys(1)}read-onlycurrent
noWirelessChannelAvailable
OBJECT-TYPE
Spectrum Management was unable to locate a suitable wireless channel to operate on
1.3.6.1.4.1.17713.11.13.5INTEGER {ok(0), noWirelessChannelAvailable(1)}read-onlycurrent
wirelessLinkDisabledWarning
OBJECT-TYPE
The SNMP ifAdminStatus of the wireless interface has disabled wireless traffic
1.3.6.1.4.1.17713.11.13.6INTEGER {ok(0), disabledBySNMPifAdminStatus(1)}read-onlycurrent
mainPSUPortDisabledWarning
OBJECT-TYPE
The SNMP ifAdminStatus of the interface has disabled Ethernet traffic
1.3.6.1.4.1.17713.11.13.7INTEGER {ok(0), disabledBySNMPifAdminStatus(1)}read-onlycurrent
sFPError
OBJECT-TYPE
If the SFP link is not OK, there are five possible causes: Either a SFP has been installed but the license key does not include SFP fiber support, a fiber link could not be established even though no LOS was detected (i.e. an optical carrier was detected, which could be due to a broken TX fiber, or because the link is disabled at the fiber link partner), a fiber link could not be established and LOS is detected (i.e. no optical carrier is detected), the installed SFP is not supported or the installed SFP failed to initialize correctly. NB: a change of status may generate an SNMP trap and/or SMTP email alert
1.3.6.1.4.1.17713.11.13.8INTEGER {ok(0), installedSFPNotLicensed(1), fiberLinkNotEstablishedButLOSNotDetected(2), fiberLinkNotEstablishedAndLOSDetected(3), installedSFPNotSupported(4), sFPInitializationFailed(5)}read-onlycurrent
mainPSUPortConfigurationMismatch
OBJECT-TYPE
The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch
1.3.6.1.4.1.17713.11.13.9INTEGER {noError(0), mismatchDetected(1)}read-onlycurrent
incompatibleMasterAndSlaveLinked
OBJECT-TYPE
A non-zero value indicates that the master and slave ends of a link are different hardware products, or have different software versions, or have different TDD Frame Configuraton Modes (Standard/Expert) in HCMP topology. NB: It is very unusual to detect this, because incompatible units will normally fail to establish a wireless link. However, some combinations may establish a partial wireless link and detect this situation. NB: A non-zero value may generate an SNMP trap and/or SMTP email alert
1.3.6.1.4.1.17713.11.13.10INTEGER {ok(0), incompatibleProductVariants(1), differentSoftwareVersionsRunning(2), tDDFrameConfigurationModeMismatch(3)}read-onlycurrent
tDDSynchronizationStatus
OBJECT-TYPE
An alarm value (displayed in red) indicates that one of the following conditions has not been met (i) An external timing system is connected or internal timing has been configured. (ii) The timing system is providing a useable reference. (iii) The ODU is locked to this reference.
1.3.6.1.4.1.17713.11.13.11INTEGER {locked(0), holdover(1), holdoverNoGPSSyncIn(2), notSynchronized(3), notSynchronizedNoGPSSyncIn(4), pTPSYNCNotConnected(5), initialising(6), clusterTimingMaster(7), acquiringLock(8), inactive(9)}read-onlycurrent
auxPortDisabledWarning
OBJECT-TYPE
The SNMP ifAdminStatus of the interface has disabled Ethernet traffic
1.3.6.1.4.1.17713.11.13.12INTEGER {ok(0), disabledBySNMPifAdminStatus(1)}read-onlycurrent
tDDSynchronizationAlarm
OBJECT-TYPE
Not Synchronized indicates failure of the external timing system for a period greater than the holdover timer. TDD frame timing will have drifted, and this link may cause interference with other links in a synchronized network. Timing System Failure is an early warning, indicating that 80% of the holdover period has expired.
1.3.6.1.4.1.17713.11.13.13INTEGER {ok(0), synchronizationLost(1), referenceSignalLost(2)}read-onlycurrent
linkModeOptimizationMismatchLinked
OBJECT-TYPE
The remote node of this link has been configured with a different link mode optimization
1.3.6.1.4.1.17713.11.13.14INTEGER {ok(0), linkModeOptimizationMismatch(1)}read-onlycurrent
auxPortConfigurationMismatch
OBJECT-TYPE
The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch. This alarm is only raised if an Out-of-Band Management Mode has been configured.
1.3.6.1.4.1.17713.11.13.15INTEGER {noError(0), mismatchDetected(1)}read-onlycurrent
secureModeAlarm
OBJECT-TYPE
The secure mode (e.g. FIPS, UC-APL) state of the unit. The secure mode is not configured(1) state indicates that the unit is capable of secure mode operation, and one or more of the following security materials has not been configured: Key Of Keys, Private Key, Public Certificate, DRNG Entropy Status, Wireless Encryption Key. The secure mode mode is configured but not active(2) state indicates that the unit is capable of secure mode operation, and the security material has been configured, but the configuration of interfaces is not consistent with secure mode operation. The secure mode is not supported(3) state indicates that the unit is not capable of secure mode operation. The secure mode capability requires appropriate hardware compatibility, license key and software image.
1.3.6.1.4.1.17713.11.13.16INTEGER {secureModeIsActive(0), secureModeIsNotConfigured(1), secureModeIsConfiguredButNotActive(2), secureModeIsNotSupported(3)}read-onlycurrent
dataBridgingStatusAlarmLinked
OBJECT-TYPE
Ethernet Data traffic bridging is disabled because the wireless link is not operating at the configured Lowest Data Modulation Mode
1.3.6.1.4.1.17713.11.13.17INTEGER {bridgingEnabled(0), bridgingDisabled(1)}read-onlycurrent
sFPPortDisabledWarning
OBJECT-TYPE
The SNMP ifAdminStatus of the interface has disabled Ethernet traffic
1.3.6.1.4.1.17713.11.13.18INTEGER {ok(0), disabledBySNMPifAdminStatus(1)}read-onlycurrent
sFPPortConfigurationMismatch
OBJECT-TYPE
The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch. This alarm is only raised if an Out-of-Band Management Mode has been configured.
1.3.6.1.4.1.17713.11.13.19INTEGER {noError(0), mismatchDetected(1)}read-onlycurrent
maxLinkRangeExceededLinked
OBJECT-TYPE
The measured link range is greater than the maximum allowed by the license key. The link will operate at a reduced capacity while this condition applies. This alarm is only raised if the license specifies a maximum link range and the trial license is not active.
1.3.6.1.4.1.17713.11.13.20INTEGER {maxLinkRangeOK(0), maxLinkRangeExceeded(1)}read-onlycurrent
nIDULanPortDisabledWarning
OBJECT-TYPE
The SNMP ifAdminStatus of the interface has disabled Ethernet traffic
1.3.6.1.4.1.17713.11.13.21INTEGER {ok(0), disabledBySNMPifAdminStatus(1)}read-onlycurrent
nIDULanPortConfigurationMismatch
OBJECT-TYPE
The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch.
1.3.6.1.4.1.17713.11.13.22INTEGER {noError(0), mismatchDetected(1)}read-onlycurrent
portAllocationMismatchLinked
OBJECT-TYPE
The local and remote ODUs have different services configured.
1.3.6.1.4.1.17713.11.13.23INTEGER {portAllocationOK(0), mismatchinOutofBandRemoteManagementService(1)}read-onlycurrent
transparentClockSourcePortAlarm
OBJECT-TYPE
Transparent Clock will not function properly because SFP, the selected clock source port is not FIBER
1.3.6.1.4.1.17713.11.13.25INTEGER {ok(0), invalidTransparentClockSourcePort(1)}read-onlycurrent
alarmInstancedTableNumber
OBJECT-TYPE
Number of entries in the alarmInstancedTable.
1.3.6.1.4.1.17713.11.13.26INTEGER (1..8)read-onlycurrent
alarmInstancedTable
OBJECT-TYPE
Instanced alarm table.
1.3.6.1.4.1.17713.11.13.27not-accessiblecurrent
alarmInstancedTableEntry
OBJECT-TYPE
Table AlarmInstancedTable
1.3.6.1.4.1.17713.11.13.27.1not-accessiblecurrent
alarmInstancedTableIndex
OBJECT-TYPE
Used to index values in the alarmInstancedTable
1.3.6.1.4.1.17713.11.13.27.1.1INTEGER (1..8)not-accessiblecurrent
incompatibleMasterAndSlave
OBJECT-TYPE
A non-zero value indicates that the master and slave ends of a link are different hardware products, or have different software versions, or have different TDD Frame Configuraton Modes (Standard/Expert) in HCMP topology. NB: It is very unusual to detect this, because incompatible units will normally fail to establish a wireless link. However, some combinations may establish a partial wireless link and detect this situation. NB: A non-zero value may generate an SNMP trap and/or SMTP email alert
1.3.6.1.4.1.17713.11.13.27.1.2INTEGER {ok(0), incompatibleProductVariants(1), differentSoftwareVersionsRunning(2), tDDFrameConfigurationModeMismatch(3)}read-onlycurrent
linkModeOptimizationMismatch
OBJECT-TYPE
The remote node of this link has been configured with a different link mode optimization
1.3.6.1.4.1.17713.11.13.27.1.3INTEGER {ok(0), linkModeOptimizationMismatch(1)}read-onlycurrent
dataBridgingStatusAlarm
OBJECT-TYPE
Ethernet Data traffic bridging is disabled because the wireless link is not operating at the configured Lowest Data Modulation Mode
1.3.6.1.4.1.17713.11.13.27.1.4INTEGER {bridgingEnabled(0), bridgingDisabled(1)}read-onlycurrent
maxLinkRangeExceeded
OBJECT-TYPE
The measured link range is greater than the maximum allowed by the license key. The link will operate at a reduced capacity while this condition applies. This alarm is only raised if the license specifies a maximum link range and the trial license is not active.
1.3.6.1.4.1.17713.11.13.27.1.5INTEGER {maxLinkRangeOK(0), maxLinkRangeExceeded(1)}read-onlycurrent
portAllocationMismatch
OBJECT-TYPE
The local and remote ODUs have different services configured.
1.3.6.1.4.1.17713.11.13.27.1.6INTEGER {portAllocationOK(0), mismatchinOutofBandRemoteManagementService(1)}read-onlycurrent
wirelessLinkStatusAlarm
OBJECT-TYPE
Current status of the wireless link. A state of Up on a green background indicates that a wireless link is established
1.3.6.1.4.1.17713.11.13.27.1.7INTEGER {up(0), down(1)}read-onlycurrent
incompatibleRegulatoryBands
OBJECT-TYPE
The master and slave units have incompatible regulatory bands. NB: Both units must have compatible license keys
1.3.6.1.4.1.17713.11.13.27.1.8INTEGER {regOK(0), regIncompatibleLicenseKeys(1)}read-onlycurrent
secureLicenseSignatureAlarm
OBJECT-TYPE
Alarm condition indicates that the unit's license is not secure enough for FIPS approved mode.
1.3.6.1.4.1.17713.11.13.28INTEGER {licenseisDSA2048signed(0), licenseisDSA1024signed(1), licensesignaturealarmisnotrelevant(2)}read-onlycurrent
apc
OBJECT-IDENTITY
1.3.6.1.4.1.17713.11.14
atpcHcmpMasterTargetRxPower
OBJECT-TYPE
The target Rx power level (dBm) at the HCMP Master that the HCMP Slaves try to reach by automatically adjusting their transmit power. The same value must be set in both the HCMP Master and Slaves as it used by the Slave to set its transmit power accurately before the wireless link is established.
1.3.6.1.4.1.17713.11.14.1INTEGER (-80..-30)read-onlycurrent
atpcHcmpMasterTxPower
OBJECT-TYPE
This must be set to the same value as the Maximum Transmit Power attribute on the HCMP Master. This is required by the HCMP Slave for initial transmit power estimation.
1.3.6.1.4.1.17713.11.14.2INTEGER (-15..30)read-onlycurrent
smtp
OBJECT-IDENTITY
1.3.6.1.4.1.17713.11.15
sMTPEmailAlert
OBJECT-TYPE
Simple Mail Transfer Protocol is used to send equipment alerts via email to a specified email address
1.3.6.1.4.1.17713.11.15.1INTEGER {disabled(0), enabled(1)}read-writecurrent
sMTPServerPortNumber
OBJECT-TYPE
Port number of the SMTP server
1.3.6.1.4.1.17713.11.15.3INTEGER (0..65535)read-writecurrent
sMTPSourceEmailAddress
OBJECT-TYPE
The 'from' email address used when constructing the automatically generated e-mail message
1.3.6.1.4.1.17713.11.15.4DisplayString (SIZE(0..63))read-writecurrent
sMTPDestinationEmailAddress
OBJECT-TYPE
The 'to' email address used when constructing the automatically generated e-mail message
1.3.6.1.4.1.17713.11.15.5DisplayString (SIZE(0..63))read-writecurrent
sMTPEnabledMessages
OBJECT-TYPE
This controls which SMTP messages the unit will send
1.3.6.1.4.1.17713.11.15.6Bits {nIDULanPortUpDown(0), sFPPortUpDown(1), auxPortUpDown(2), mainPSUPortUpDown(3), enabledDiagnosticAlarms(4), dFSImpulseInterference(5), channelChange(6), wirelessPortUpDown(7), listenBeforeTalk(15)}read-writecurrent
sMTPServerInternetAddressType
OBJECT-TYPE
The type of Internet address specified by the associated sMTPServerInternetAddress.
1.3.6.1.4.1.17713.11.15.7INTEGER {unknown(0), ipv4(1), ipv6(2), ipv4z(3), ipv6z(4), unknown6(5), unknown7(6), unknown8(7), unknown9(8), unknown10(9), unknown11(10), unknown12(11), unknown13(12), unknown14(13), unknown15(14), unknown16(15), dns(16)}read-onlycurrent
sMTPServerInternetAddress
OBJECT-TYPE
Internet address of the SMTP server
1.3.6.1.4.1.17713.11.15.8InetAddressread-writecurrent
sMTPServerResolvedInternetAddress
OBJECT-TYPE
IP Address of the SMTP Server.
1.3.6.1.4.1.17713.11.15.9DisplayString (SIZE(0..63))read-onlycurrent
snmpControl
OBJECT-IDENTITY
1.3.6.1.4.1.17713.11.16
sNMPPortNumber
OBJECT-TYPE
The IP port number used to access the SNMP MIB (i.e. Gets and Sets) (default = 161). NB: A system reboot is required to activate changes to this attribute
1.3.6.1.4.1.17713.11.16.1INTEGER (0..65535)read-writecurrent
sNMPCommunityString
OBJECT-TYPE
The SNMP community string. NB: A system reboot is required to activate changes to this attribute
1.3.6.1.4.1.17713.11.16.2DisplayString (SIZE(0..63))read-writecurrent
sNMPTrapTableNumber
OBJECT-TYPE
Number of entries in the sNMPTrapTable.
1.3.6.1.4.1.17713.11.16.3INTEGER (2)read-onlycurrent
sNMPTrapTable
OBJECT-TYPE
SNMP trap configuration table.
1.3.6.1.4.1.17713.11.16.4not-accessiblecurrent
sNMPTrapTableEntry
OBJECT-TYPE
Table SNMPTrapTable
1.3.6.1.4.1.17713.11.16.4.1not-accessiblecurrent
sNMPTrapTableIndex
OBJECT-TYPE
SNMP trap value, used to index the SNMPTrapTable.
1.3.6.1.4.1.17713.11.16.4.1.1INTEGER (1..2)not-accessiblecurrent
sNMPTrapPortNumber
OBJECT-TYPE
Destination port for SNMP Traps (default=162). NB: A system reboot is required to activate changes to this attribute.
1.3.6.1.4.1.17713.11.16.4.1.3INTEGER (0..65535)read-writecurrent
sNMPTrapInternetAddressType
OBJECT-TYPE
The type of Internet address specified by the associated sNMPTrapInternetAddress.
1.3.6.1.4.1.17713.11.16.4.1.4INTEGER {unknown(0), ipv4(1), ipv6(2), ipv4z(3), ipv6z(4), unknown6(5), unknown7(6), unknown8(7), unknown9(8), unknown10(9), unknown11(10), unknown12(11), unknown13(12), unknown14(13), unknown15(14), unknown16(15), dns(16)}read-onlycurrent
sNMPTrapInternetAddress
OBJECT-TYPE
The Internet address to which all SNMP Traps are sent.
1.3.6.1.4.1.17713.11.16.4.1.5InetAddressread-writecurrent
sNMPTrapReceiverEnabled
OBJECT-TYPE
A value of 0 disables the sending of SNMP trap to corresponding receiver. A value of 1 enables the sending of SNMP trap to corresponding receiver.
1.3.6.1.4.1.17713.11.16.4.1.6INTEGER {disabled(0), enabled(1)}read-writecurrent
sNMPTrapResolvedInternetAddress
OBJECT-TYPE
IP Address(es) of the SNMP Trap Server.
1.3.6.1.4.1.17713.11.16.4.1.7DisplayString (SIZE(0..127))read-onlycurrent
sNMPTrapVersion
OBJECT-TYPE
The SNMP protocol version to use for SNMP Traps. NB: A system reboot is required to activate changes to this attribute
1.3.6.1.4.1.17713.11.16.5INTEGER {v1(0), v2c(1)}read-writecurrent
sNMPEnabledTraps
OBJECT-TYPE
This controls which SNMP Traps the unit will send
1.3.6.1.4.1.17713.11.16.6Bits {auxPortUpDown(0), mainPSUPortUpDown(1), authenticationFailure(2), enabledDiagnosticAlarms(3), dFSImpulseInterference(4), channelChange(5), wirelessPortUpDown(6), coldStart(7), listenBeforeTalk(13), nIDULanPortUpDown(14), sFPPortUpDown(15)}read-writecurrent
enabledDiagnosticAlarms
OBJECT-TYPE
Controls which individual diagnostic alarms are enabled. The unit may be configured to generate SNMP traps and/or SMTP email alerts for these enabled alarms by selecting 'Enabled Diagnostic Alarms' on the 'SNMP Enabled Traps' and/or 'SMTP Enabled Messages' attributes
1.3.6.1.4.1.17713.11.16.7Bits {portState(0), incompatibleMasterAndSlave(1), incompatibleRegulatoryBands(2), maximumLinkRangeExceeded(3), unitOutOfCalibration(4), installArmState(5), installStatus(6), regulatoryBand(7), syslogLocalWrapped(8), syslogLocalNearlyFull(9), syslogDisabledWarning(10), linkModeOptimizationMismatch(11), tDDSynchronizationAlarm(12), wirelessLinkDisabledWarning(13), sNTPSynchronizationFailed(14), noWirelessChannelAvailable(15), licenseSignatureLengthAlarm(16), wirelessLinkStatus(17), tDMAlarms(18), capacityVariantMismatch(19), remainingFullCapacityTrialTime(20), dataBridgingStatus(21), secureModeAlarm(22), syslogClientDisabledWarning(23)}read-writecurrent
sNMPSendAllTrapsAtStartup
OBJECT-TYPE
Controls whether cleared traps are reported at start-up as well as raised traps. Only enabled traps will be reported. NB: Traps corresponding to transient events (i.e. not associated with an alarm or status value) are only sent when required and not at start-up.
1.3.6.1.4.1.17713.11.16.8INTEGER {disabled(0), enabled(1)}read-writecurrent
sntp
OBJECT-IDENTITY
1.3.6.1.4.1.17713.11.17
sNTPState
OBJECT-TYPE
SNTP control state
1.3.6.1.4.1.17713.11.17.1INTEGER {disabled(0), enabled(1)}read-writecurrent
sNTPPollInterval
OBJECT-TYPE
The SNTP server polling interval
1.3.6.1.4.1.17713.11.17.4INTEGER (60..43200)read-writecurrent
sNTPSync
OBJECT-TYPE
If SNTP Sync fails then check the server settings in the Remote Management page, or disable SNTP
1.3.6.1.4.1.17713.11.17.5INTEGER {noSync(0), inSync(1)}read-onlycurrent
sNTPLastSync
OBJECT-TYPE
Last SNTP sync time
1.3.6.1.4.1.17713.11.17.6Integer32read-onlycurrent
systemClock
OBJECT-TYPE
System clock presented as local time
1.3.6.1.4.1.17713.11.17.7Integer32read-onlycurrent
timeZone
OBJECT-TYPE
Time zone offsets from Greenwich Mean Time (GMT)
1.3.6.1.4.1.17713.11.17.8INTEGER {gmtMinus1200(0), gmtMinus1130(1), gmtMinus1100(2), gmtMinus1030(3), gmtMinus1000(4), gmtMinus0930(5), gmtMinus0900(6), gmtMinus0830(7), gmtMinus0800(8), gmtMinus0730(9), gmtMinus0700(10), gmtMinus0630(11), gmtMinus0600(12), gmtMinus0530(13), gmtMinus0500(14), gmtMinus0430(15), gmtMinus0400(16), gmtMinus0330(17), gmtMinus0300(18), gmtMinus0230(19), gmtMinus0200(20), gmtMinus0130(21), gmtMinus0100(22), gmtMinus0030(23), gmtZero(24), gmtPlus0030(25), gmtPlus0100(26), gmtPlus0130(27), gmtPlus0200(28), gmtPlus0230(29), gmtPlus0300(30), gmtPlus0330(31), gmtPlus0400(32), gmtPlus0430(33), gmtPlus0500(34), gmtPlus0530(35), gmtPlus0600(36), gmtPlus0630(37), gmtPlus0700(38), gmtPlus0730(39), gmtPlus0800(40), gmtPlus0830(41), gmtPlus0900(42), gmtPlus0930(43), gmtPlus1000(44), gmtPlus1030(45), gmtPlus1100(46), gmtPlus1130(47), gmtPlus1200(48), gmtPlus1230(49), gmtPlus1300(50)}read-writecurrent
daylightSaving
OBJECT-TYPE
Daylight Saving Time
1.3.6.1.4.1.17713.11.17.9INTEGER {disabled(0), enabled(1)}read-writecurrent
sNTPPrimaryServer
OBJECT-TYPE
Specifies the primary SNTP server, determining the order in which the servers are tried.
1.3.6.1.4.1.17713.11.17.10INTEGER {server1(0), server2(1)}read-writecurrent
sNTPPrimaryServerDeadTime
OBJECT-TYPE
Time (in seconds) to wait before retrying communications with an unresponsive primary SNTP server. Setting the value to 0 disables the timer.
1.3.6.1.4.1.17713.11.17.11INTEGER (0..86400)read-writecurrent
sNTPServerRetries
OBJECT-TYPE
Number of times the device will retry after an SNTP server fails to respond.
1.3.6.1.4.1.17713.11.17.12INTEGER (0..10)read-writecurrent
sNTPServerTimeout
OBJECT-TYPE
Time (in seconds) the device will wait for a response from an SNTP server.
1.3.6.1.4.1.17713.11.17.13INTEGER (1..15)read-writecurrent
sNTPServerTableNumber
OBJECT-TYPE
Number of entries in the SNTPServerTable.
1.3.6.1.4.1.17713.11.17.14INTEGER (2)read-onlycurrent
sNTPServerTable
OBJECT-TYPE
1.3.6.1.4.1.17713.11.17.15not-accessiblecurrent
sNTPServerTableEntry
OBJECT-TYPE
Table SNTPServerTable
1.3.6.1.4.1.17713.11.17.15.1not-accessiblecurrent
sNTPServerTableIndex
OBJECT-TYPE
Index range for the SNTPServerTable.
1.3.6.1.4.1.17713.11.17.15.1.1INTEGER (1..2)not-accessiblecurrent
sNTPServerPortNumber
OBJECT-TYPE
The IP port number of the SNTP server. Defaults to port 123.
1.3.6.1.4.1.17713.11.17.15.1.3INTEGER (0..65535)read-writecurrent
sNTPServerStatus
OBJECT-TYPE
Status message reflecting the result of communications with the SNTP server when last polled
1.3.6.1.4.1.17713.11.17.15.1.4DisplayString (SIZE(0..127))read-onlycurrent
sNTPServerInternetAddressType
OBJECT-TYPE
The type of Internet address specified by the associated sNTPServerInternetAddress.
1.3.6.1.4.1.17713.11.17.15.1.5INTEGER {unknown(0), ipv4(1), ipv6(2), ipv4z(3), ipv6z(4), unknown6(5), unknown7(6), unknown8(7), unknown9(8), unknown10(9), unknown11(10), unknown12(11), unknown13(12), unknown14(13), unknown15(14), unknown16(15), dns(16)}read-onlycurrent
sNTPServerInternetAddress
OBJECT-TYPE
The Internet address of a valid SNTP server
1.3.6.1.4.1.17713.11.17.15.1.6InetAddressread-writecurrent
sNTPServerResolvedInternetAddress
OBJECT-TYPE
IP Address of the SNTP Server.
1.3.6.1.4.1.17713.11.17.15.1.7DisplayString (SIZE(0..63))read-onlycurrent
sNTPServerAuthenticationProtocol
OBJECT-TYPE
Authentication protocol to be used for this SNTP server. Options are None (default) or MD5.
1.3.6.1.4.1.17713.11.17.15.1.8INTEGER {none(0), mD5(1), sHA1(2)}read-onlycurrent
sNTPServerKeyIdentifier
OBJECT-TYPE
SNTP key identifier. Note: Key 0 is reserved for testing using the well-known key all zeroes.
1.3.6.1.4.1.17713.11.17.15.1.9Integer32read-onlycurrent
reset
OBJECT-IDENTITY
1.3.6.1.4.1.17713.11.18
systemReset
OBJECT-TYPE
Setting this attribute to '1' will cause a system reboot. NB: a system reboot will apply any pending new settings held in memory
1.3.6.1.4.1.17713.11.18.1INTEGER {running(0), consoleReboot(1)}read-writecurrent
versions
OBJECT-IDENTITY
1.3.6.1.4.1.17713.11.19
softwareVersion
OBJECT-TYPE
Current software version
1.3.6.1.4.1.17713.11.19.1DisplayString (SIZE(0..63))read-onlycurrent
hardwareVersion
OBJECT-TYPE
Hardware platform version
1.3.6.1.4.1.17713.11.19.2DisplayString (SIZE(0..63))read-onlycurrent
secondarySoftwareVersion
OBJECT-TYPE
Secondary software version, used when the primary software image is invalid or erased
1.3.6.1.4.1.17713.11.19.3DisplayString (SIZE(0..63))read-onlycurrent
bootVersion
OBJECT-TYPE
Boot code software version
1.3.6.1.4.1.17713.11.19.4DisplayString (SIZE(0..63))read-onlycurrent
pubStats
OBJECT-IDENTITY
1.3.6.1.4.1.17713.11.20
receiveDataRateLinked
OBJECT-TYPE
Average data rate over the last one second interval (kbps)
1.3.6.1.4.1.17713.11.20.1Integer32read-onlycurrent
transmitDataRateLinked
OBJECT-TYPE
Average data rate over the last one second interval (kbps)
1.3.6.1.4.1.17713.11.20.2Integer32read-onlycurrent
aggregateDataRateLinked
OBJECT-TYPE
Average data rate over the last one second interval (kbps)
1.3.6.1.4.1.17713.11.20.3Integer32read-onlycurrent
wirelessLinkAvailabilityLinked
OBJECT-TYPE
Link availability calculated since the last reset of the system counters, as a percentage multiplied by 10000 to give four decimal places of precision
1.3.6.1.4.1.17713.11.20.4INTEGER (0..1000000)read-onlycurrent
wirelessLinkStatusLinked
OBJECT-TYPE
Current status of the wireless link
1.3.6.1.4.1.17713.11.20.5INTEGER {up(0), registering(1), searching(2), acquiring(3), radarCAC(4), initialising(5)}read-onlycurrent
byteErrorRatioLinked
OBJECT-TYPE
Reciprocal of the byte error ratio calculated since the last reset of the system counters
1.3.6.1.4.1.17713.11.20.6Integer32read-onlycurrent
receiveModulationModeDetailLinked
OBJECT-TYPE
The reason for the current receive modulation mode
1.3.6.1.4.1.17713.11.20.7INTEGER {runningAtMaximumReceiveMode(0), runningAtUserConfiguredMaxModulationMode(1), restrictedBecauseInstallationIsArmed(2), restrictedBecauseOfByteErrorsOnTheWirelessLink(3), restrictedBecauseTheLinkParametersAreUpdating(4), restrictedBecauseChannelChangeIsInProgress(5), restrictedDueToTheLowEthernetLinkSpeed(6), runningAtMaximumReceiveModeForChannelBandwidth(7), limitedByTheWirelessConditions(8), restrictedBecauseFullCapabilityTrialLicenseExpired(9)}read-onlycurrent
dataBridgingAvailabilityLinked
OBJECT-TYPE
Link availability bridging Ethernet Data traffic calculated since the last reset of the system counters, as a percentage multiplied by 10000 to give four decimal places of precision
1.3.6.1.4.1.17713.11.20.8INTEGER (0..1000000)read-onlycurrent
pubInstancedStatsTableNumber
OBJECT-TYPE
Number of entries in the pubInstancedStatsTable.
1.3.6.1.4.1.17713.11.20.9INTEGER (1..8)read-onlycurrent
pubInstancedStatsTable
OBJECT-TYPE
Instanced Public stats table.
1.3.6.1.4.1.17713.11.20.10not-accessiblecurrent
pubInstancedStatsTableEntry
OBJECT-TYPE
Table PubInstancedStatsTable
1.3.6.1.4.1.17713.11.20.10.1not-accessiblecurrent
pubInstancedStatsTableIndex
OBJECT-TYPE
Used to index the pubInstancedStatsTable.
1.3.6.1.4.1.17713.11.20.10.1.1INTEGER (1..8)not-accessiblecurrent
receiveDataRate
OBJECT-TYPE
Histogram of the average link receive data rate.
1.3.6.1.4.1.17713.11.20.10.1.2Integer32read-onlycurrent
transmitDataRate
OBJECT-TYPE
Histogram of the average link transmit data rate.
1.3.6.1.4.1.17713.11.20.10.1.3Integer32read-onlycurrent
aggregateDataRate
OBJECT-TYPE
Histogram of the link aggregate data rate.
1.3.6.1.4.1.17713.11.20.10.1.4Integer32read-onlycurrent
wirelessLinkAvailability
OBJECT-TYPE
Link availability calculated since the last reset of the system counters
1.3.6.1.4.1.17713.11.20.10.1.5INTEGER (0..1000000)read-onlycurrent
wirelessLinkStatus
OBJECT-TYPE
Current status of the wireless link. A state of 'Up' on a green background indicates that a wireless link is established
1.3.6.1.4.1.17713.11.20.10.1.6INTEGER {up(0), registering(1), searching(2), acquiring(3), radarCAC(4), initialising(5)}read-onlycurrent
receiveModulationModeDetail
OBJECT-TYPE
A brief description of the reason for the current receive modulation mode
1.3.6.1.4.1.17713.11.20.10.1.7INTEGER {runningAtMaximumReceiveMode(0), runningAtUserConfiguredMaxModulationMode(1), restrictedBecauseInstallationIsArmed(2), restrictedBecauseOfByteErrorsOnTheWirelessLink(3), restrictedBecauseTheLinkParametersAreUpdating(4), restrictedBecauseChannelChangeIsInProgress(5), restrictedDueToTheLowEthernetLinkSpeed(6), runningAtMaximumReceiveModeForChannelBandwidth(7), limitedByTheWirelessConditions(8), restrictedBecauseFullCapabilityTrialLicenseExpired(9), acquiringLink(10)}read-onlycurrent
dataBridgingAvailability
OBJECT-TYPE
Link availability for bridging Ethernet Data traffic calculated since the last reset of the system counters
1.3.6.1.4.1.17713.11.20.10.1.8INTEGER (0..1000000)read-onlycurrent
byteErrorRatio
OBJECT-TYPE
Reciprocal of the byte error ratio calculated since the last reset of the system counters
1.3.6.1.4.1.17713.11.20.10.1.9Integer32read-onlycurrent
wirelessOutEthernetOctets
OBJECT-TYPE
Cumulative total of octets transmitted in data or management service at the wireless interface. This excludes wireless MAC headers, MAC management messages, and Null bytes.
1.3.6.1.4.1.17713.11.20.10.1.10Counter64read-onlycurrent
wirelessOutAllOctets
OBJECT-TYPE
Cumulative total of octets transmitted at the wireless interface. This includes data service, management service, wireless MAC headers, MAC management messages, and Null bytes.
1.3.6.1.4.1.17713.11.20.10.1.11Counter64read-onlycurrent
wirelessOutOctets
OBJECT-TYPE
Cumulative total of octets including wireless MAC headers transmitted in data or management service at the wireless interface. This excludes MAC management messages and Null bytes.
1.3.6.1.4.1.17713.11.20.10.1.12Counter64read-onlycurrent
erroredSeconds
OBJECT-TYPE
erroredSeconds count for any second period containing one or more codeword errors since the last reset of the system counters.
1.3.6.1.4.1.17713.11.20.10.1.13Integer32read-onlycurrent
severelyErroredSeconds
OBJECT-TYPE
severelyErroredSeconds count for any second period containing ten or more codeword errors since the last reset of the system counters.
1.3.6.1.4.1.17713.11.20.10.1.14Integer32read-onlycurrent
unavailableSeconds
OBJECT-TYPE
unavailableSeconds count for any second when Data Bridging Status = Disabled since the last reset of the system counters. Note erroredSeconds and severelyErroredSeconds are not incremented when the link is unavailable.
1.3.6.1.4.1.17713.11.20.10.1.15Integer32read-onlycurrent
encryption
OBJECT-IDENTITY
1.3.6.1.4.1.17713.11.22
encryptionAlgorithm
OBJECT-TYPE
The Encryption Algorithm used by the wireless link. NB: A system reboot is required to activate changes to this attribute. NB: The same Encryption Algorithm must be configured at BOTH ends of the link for it to function correctly. TLS RSA Encryption Algorithm is not compatible with Link Name access method.
1.3.6.1.4.1.17713.11.22.1INTEGER {none(0), pSKAES128bit(1), pSKAES192bit(2), pSKAES256bit(3), tLSRSA(4), tLSPSK128bit(5), tLSPSK256bit(6)}read-onlycurrent
tLSMinimumSecurityLevel
OBJECT-TYPE
The minimum level of security that is supported on the device
1.3.6.1.4.1.17713.11.22.2INTEGER {none(0), aES128bitTLSRSA(1), aES256bitTLSRSA(2)}read-onlycurrent
tDDControl
OBJECT-IDENTITY
1.3.6.1.4.1.17713.11.23
tDDSynchronizationMode
OBJECT-TYPE
TDD Synchronization Mode selection
1.3.6.1.4.1.17713.11.23.1INTEGER {disabled(0), enabled(1)}read-onlycurrent
hCMPMaximumLinkRange
OBJECT-TYPE
The maximum link range between the HCMP Master and any HCMP Slave. The same value must be used on both the HCMP Master and its Slaves.
1.3.6.1.4.1.17713.11.23.2INTEGER (50..1000)read-onlycurrent
maximumNumberOfSlaves
OBJECT-TYPE
The maximum number of HCMP Slaves that an HCMP Master can simultaneously connect to. The same value has to be used in both the HCMP Master and its Slaves.
1.3.6.1.4.1.17713.11.23.3INTEGER (1..8)read-onlycurrent
hCMPLinkSymmetry
OBJECT-TYPE
Provides configuration options for sharing the available wireless capacity among all Slaves between the transmit and receive directions. Option x to y is the ratio of Total Downlink capacity to Total Uplink Capacity. The same value has to be used in both the HCMP Master and its Slaves.
1.3.6.1.4.1.17713.11.23.4INTEGER {symmetry4to1(0), symmetry3to1(1), symmetry2to1(2), symmetry1to1(3), symmetry1to2(4), symmetry1to3(5), symmetry1to4(6)}read-onlycurrent
syslogControl
OBJECT-IDENTITY
1.3.6.1.4.1.17713.11.24
syslogClient
OBJECT-TYPE
Enable or disable the syslog client
1.3.6.1.4.1.17713.11.24.1INTEGER {disabled(0), enabled(1)}read-onlycurrent
syslogState
OBJECT-TYPE
The syslog service has been enabled or disabled
1.3.6.1.4.1.17713.11.24.2INTEGER {disabled(0), enabled(1)}read-onlycurrent
aAAControl
OBJECT-IDENTITY
1.3.6.1.4.1.17713.11.25
userTableNumber
OBJECT-TYPE
Number of entries in the userTable
1.3.6.1.4.1.17713.11.25.1INTEGER (1..10)read-onlycurrent
userTable
OBJECT-TYPE
The User Table Control group contains objects specifically for user account management.
1.3.6.1.4.1.17713.11.25.2not-accessiblecurrent
userTableEntry
OBJECT-TYPE
Table UserTable
1.3.6.1.4.1.17713.11.25.2.1not-accessiblecurrent
userTableIndex
OBJECT-TYPE
used to index values in the userTable.
1.3.6.1.4.1.17713.11.25.2.1.1INTEGER (1..10)not-accessiblecurrent
userName
OBJECT-TYPE
User name which must be entered, along with the appropriate password, in order to gain access to the system.
1.3.6.1.4.1.17713.11.25.2.1.2DisplayString (SIZE(0..67))read-onlycurrent
userRole
OBJECT-TYPE
Role of the selected user. A Security Officer has access to and can modify all settings. A System Administrator has access to and can modify all non-security settings. A Read Only user can view settings, but cannot make any changes.
1.3.6.1.4.1.17713.11.25.2.1.3INTEGER {readOnly(0), systemAdministrator(1), securityOfficer(2)}read-onlycurrent
userEnabled
OBJECT-TYPE
Enable / Disable the selected user
1.3.6.1.4.1.17713.11.25.2.1.4INTEGER {disabled(0), enabled(1)}read-onlycurrent
userPassword
OBJECT-TYPE
User password, which must be entered in order to gain access to the system.
1.3.6.1.4.1.17713.11.25.2.1.5DisplayString (SIZE(0..67))read-writecurrent
routerProtocols
OBJECT-IDENTITY
1.3.6.1.4.1.17713.11.26
microwaveAdaptiveBandwidth
OBJECT-TYPE
Enable support of Microwave Adaptive Bandwidth Protocol. MAB is disabled if link symmetry is configured as Adaptive
1.3.6.1.4.1.17713.11.26.1INTEGER {disabled(0), enabled(1)}read-onlycurrent
mABNominalModulationMode
OBJECT-TYPE
The Nominal modulation mode is the desired modulation mode. MAB VSM packets are generated when the current modulation mode falls below the nominal modulation.
1.3.6.1.4.1.17713.11.26.2INTEGER {modAcquisition(0), modBpsk63percent(1), modQpsk63percentSingle(2), modTransient1(3), modQpsk87percentSingle(4), modTransient2(5), mod16qam63percentSingleA(6), modTransient3(7), mod16qam87percentSingle(8), modTransient4(9), mod64qam75percentSingle(10), modTransient5(11), mod64qam92percentSingle(12), modTransient6(13), mod256qam81percentSingle(14), mod16qam63percentSingleB(15), mod16qam63percentDual(16), modTransient7(17), mod16qam87percentDual(18), modTransient8(19), mod64qam75percentDual(20), modTransient9(21), mod64qam92percentDual(22), modTransient10(23), mod256qam81percentDual(24)}read-onlycurrent
mABTransmissionInterval
OBJECT-TYPE
The minimum interval (in seconds) between successive MAB vendor specific messages (VSM). These VSM are sent when the current transmit capacity falls below the configured MAB Nominal Modulation Mode.
1.3.6.1.4.1.17713.11.26.3INTEGER {transmissionInterval1s(0), transmissionInterval10s(1), transmissionInterval60s(2)}read-onlycurrent
mABHoldoffPeriod
OBJECT-TYPE
The period (in seconds) over which transmit capacity is averaged over to determine when the wireless link has degraded
1.3.6.1.4.1.17713.11.26.4INTEGER (10..60)read-onlycurrent
mABMaintenanceLevel
OBJECT-TYPE
Maintenance Levels (0-7) determines the destination MAC address of MAB vendor specific messages.
1.3.6.1.4.1.17713.11.26.5INTEGER (0..7)read-onlycurrent
useVLANForMABProtocol
OBJECT-TYPE
This controls whether MAB vendor specific messages (VSM) packets use VLAN tags or not.
1.3.6.1.4.1.17713.11.26.6INTEGER {noVLANTagging(0), iEEE8021QTaggedCTagType8100(1)}read-onlycurrent
mABProtocolVID
OBJECT-TYPE
This VLAN VID (0-4094) will be included in MAB vendor specific messages (VSM) packets.
1.3.6.1.4.1.17713.11.26.7INTEGER (0..4094)read-onlycurrent
mABProtocolVLANPriority
OBJECT-TYPE
This VLAN Priority (0-7) will be included in MAB vendor specific messages (VSM) packets.
1.3.6.1.4.1.17713.11.26.8INTEGER (0..7)read-onlycurrent
mABState
OBJECT-TYPE
Current state of MAB Protocol. A state of 'Normal' on a green background indicates that a wireless link is operating at nominal capacity
1.3.6.1.4.1.17713.11.26.9INTEGER {normal(0), degraded(1)}read-onlycurrent
mABNominalTransmitCapacity
OBJECT-TYPE
The nominal Tx capacity used in MAB Vendor Specific Messages for the selected nominal modulation mode
1.3.6.1.4.1.17713.11.26.10INTEGER (0..1000)read-onlycurrent
mABCurrentTransmitCapacity
OBJECT-TYPE
The current Tx capacity of the wireless link used in the last MAB Vendor Specific Message transmitted.
1.3.6.1.4.1.17713.11.26.11INTEGER (0..1000)read-onlycurrent
cableDiagnostics
OBJECT-IDENTITY
1.3.6.1.4.1.17713.11.27
cableDiagnosticsPorts
OBJECT-TYPE
Select ports on which Cable Diagnostics must be executed
1.3.6.1.4.1.17713.11.27.1Bits {auxPort(6), mainPSUPort(7)}read-writecurrent
cableDiagnosticsControl
OBJECT-TYPE
Set this attribute to 'Test in Progress' to start a Cable Diagnostics test
1.3.6.1.4.1.17713.11.27.2INTEGER {startTest(0), testInProgress(1)}read-writecurrent
cableDiagnosticsWarning
OBJECT-TYPE
Normal Ethernet operation is disrupted when a Cable Diagnostics test is in progress
1.3.6.1.4.1.17713.11.27.3INTEGER {idle(0), testInProgress(1)}read-onlycurrent
cableDiagnosticsResultTableNumber
OBJECT-TYPE
Number of rows in the Cable Diagnostics Result Table.
1.3.6.1.4.1.17713.11.27.4INTEGER (1..2)read-onlycurrent
cableDiagnosticsResultTable
OBJECT-TYPE
1.3.6.1.4.1.17713.11.27.5not-accessiblecurrent
cableDiagnosticsResultTableEntry
OBJECT-TYPE
Table CableDiagnosticsResultTable
1.3.6.1.4.1.17713.11.27.5.1not-accessiblecurrent
cableDiagnosticsResultTableIndex
OBJECT-TYPE
Cable Diagnostics Port value used to index into the result table.
1.3.6.1.4.1.17713.11.27.5.1.1INTEGER (1..2)not-accessiblecurrent
cableDiagnosticsResultsDateTime
OBJECT-TYPE
The Date and Time when a Cable Diagnostics test was last executed
1.3.6.1.4.1.17713.11.27.5.1.2Integer32read-onlycurrent
cableDiagPair1Results
OBJECT-TYPE
The result of the most recent execution of Cable Diagnostics on cable pair 1. According to the T658B wiring scheme, pair 1 is pins 4 & 5 on the RJ45 socket on the ODU. Open Circuit is reported when the impedance is greater than 330 ohms. Short Circuit is reported when the impedance is less than 33 ohms. Unknown is reported when a continuous signal is received from the link partner for 125 ms, preventing start of the test.
1.3.6.1.4.1.17713.11.27.5.1.3INTEGER {ok(0), unknown(1), inProgress(2), notTested(3), openCircuit(4), shortCircuit(5)}read-onlycurrent
cableDiagPair1Distance
OBJECT-TYPE
The distance in meters from the ODU to the fault detected on the cable pair during the most recent execution of Cable Diagnostics. Faults in cables longer than 160 meters (525 feet) may not be detected. The error margin is +/-2 meters (6.5 feet).
1.3.6.1.4.1.17713.11.27.5.1.4Integer32read-onlycurrent
cableDiagPair2Results
OBJECT-TYPE
The result of the most recent execution of Cable Diagnostics on cable pair 2. According to the T658B wiring scheme, pair 2 is pins 1 & 2 on the RJ45 socket on the ODU. Open Circuit is reported when the impedance is greater than 330 ohms. Short Circuit is reported when the impedance is less than 33 ohms. Unknown is reported when a continuous signal is received from the link partner for 125 ms, preventing start of the test.
1.3.6.1.4.1.17713.11.27.5.1.5INTEGER {ok(0), unknown(1), inProgress(2), notTested(3), openCircuit(4), shortCircuit(5)}read-onlycurrent
cableDiagPair2Distance
OBJECT-TYPE
The distance in meters from the ODU to the fault detected on the cable pair during the most recent execution of Cable Diagnostics. Faults in cables longer than 160 meters (525 feet) may not be detected. The error margin is +/-2 meters (6.5 feet).
1.3.6.1.4.1.17713.11.27.5.1.6Integer32read-onlycurrent
cableDiagPair3Results
OBJECT-TYPE
The result of the most recent execution of Cable Diagnostics on cable pair 3. According to the T658B wiring scheme, pair 3 is pins 3 & 6 on the RJ45 socket on the ODU. Open Circuit is reported when the impedance is greater than 330 ohms. Short Circuit is reported when the impedance is less than 33 ohms. Unknown is reported when a continuous signal is received from the link partner for 125 ms, preventing start of the test.
1.3.6.1.4.1.17713.11.27.5.1.7INTEGER {ok(0), unknown(1), inProgress(2), notTested(3), openCircuit(4), shortCircuit(5)}read-onlycurrent
cableDiagPair3Distance
OBJECT-TYPE
The distance in meters from the ODU to the fault detected on the cable pair during the most recent execution of Cable Diagnostics. Faults in cables longer than 160 meters (525 feet) may not be detected. The error margin is +/-2 meters (6.5 feet).
1.3.6.1.4.1.17713.11.27.5.1.8Integer32read-onlycurrent
cableDiagPair4Results
OBJECT-TYPE
The result of the most recent execution of Cable Diagnostics on cable pair 4. According to the T658B wiring scheme, pair 4 is pins 7 & 8 on the RJ45 socket on the ODU. Open Circuit is reported when the impedance is greater than 330 ohms. Short Circuit is reported when the impedance is less than 33 ohms. Unknown is reported when a continuous signal is received from the link partner for 125 ms, preventing start of the test.
1.3.6.1.4.1.17713.11.27.5.1.9INTEGER {ok(0), unknown(1), inProgress(2), notTested(3), openCircuit(4), shortCircuit(5)}read-onlycurrent
cableDiagPair4Distance
OBJECT-TYPE
The distance in meters from the ODU to the fault detected on the cable pair during the most recent execution of Cable Diagnostics. Faults in cables longer than 160 meters (525 feet) may not be detected. The error margin is +/-2 meters (6.5 feet).
1.3.6.1.4.1.17713.11.27.5.1.10Integer32read-onlycurrent
unitIdentification
OBJECT-IDENTITY
1.3.6.1.4.1.17713.11.28
deviceMACAddress
OBJECT-TYPE
Device MAC address
1.3.6.1.4.1.17713.11.28.1OCTET STRING (SIZE(6))read-onlycurrent
deviceESN
OBJECT-TYPE
The ESN assigned to this device
1.3.6.1.4.1.17713.11.28.2DisplayString (SIZE(0..63))read-onlycurrent
deviceMSN
OBJECT-TYPE
The MSN assigned to this device
1.3.6.1.4.1.17713.11.28.3DisplayString (SIZE(0..63))read-onlycurrent
authorizationControl
OBJECT-IDENTITY
1.3.6.1.4.1.17713.11.29
authorizationControlTableNumber
OBJECT-TYPE
Number of entries in the AuthorizationControlTable.
1.3.6.1.4.1.17713.11.29.1INTEGER (1..32)read-onlycurrent
authorizationControlTable
OBJECT-TYPE
AuthorizationControlTable - used to validate an RM trying to connect to it.
1.3.6.1.4.1.17713.11.29.2not-accessiblecurrent
authorizationControlTableEntry
OBJECT-TYPE
Table AuthorizationControlTable
1.3.6.1.4.1.17713.11.29.2.1not-accessiblecurrent
authorizationControlTableIndex
OBJECT-TYPE
Authorization Control Table Index
1.3.6.1.4.1.17713.11.29.2.1.1INTEGER (1..32)not-accessiblecurrent
whitelistRMMacAddress
OBJECT-TYPE
MAC Address of Remote Modules.
1.3.6.1.4.1.17713.11.29.2.1.2OCTET STRING (SIZE(6))read-writecurrent
whitelistRMEnabled
OBJECT-TYPE
Whether this Remote Module is enabled. Only Enabled Remote Modules are allowed to connect to this device.
1.3.6.1.4.1.17713.11.29.2.1.3INTEGER {disabled(0), enabled(1)}read-writecurrent
blacklistRMMacAddress
OBJECT-TYPE
MAC Address of Remote Modules.
1.3.6.1.4.1.17713.11.29.2.1.4OCTET STRING (SIZE(6))read-writecurrent
blacklistRMEnabled
OBJECT-TYPE
Whether this Remote Module is enabled. Only Enabled Remote Modules are black listed; they cannot connect to this ODU.
1.3.6.1.4.1.17713.11.29.2.1.5INTEGER {disabled(0), enabled(1)}read-writecurrent
dNS
OBJECT-IDENTITY
1.3.6.1.4.1.17713.11.30
dNSResolver
OBJECT-TYPE
Enable/Disable DNS Resolver.
1.3.6.1.4.1.17713.11.30.1INTEGER {disabled(0), enabled(1)}read-writecurrent
dNSPrimaryServer
OBJECT-TYPE
Specifies the primary DNS server, determining the order in which the servers are tried.
1.3.6.1.4.1.17713.11.30.2INTEGER {server1(0), server2(1)}read-onlycurrent
dNSServerTableNumber
OBJECT-TYPE
Number of entries in the DNSServerTable.
1.3.6.1.4.1.17713.11.30.3INTEGER (2)read-onlycurrent
dNSServerTable
OBJECT-TYPE
1.3.6.1.4.1.17713.11.30.4not-accessiblecurrent
dNSServerTableEntry
OBJECT-TYPE
Table DNSServerTable
1.3.6.1.4.1.17713.11.30.4.1not-accessiblecurrent
dNSServerTableIndex
OBJECT-TYPE
Index range for the DNSServerTable.
1.3.6.1.4.1.17713.11.30.4.1.1INTEGER (1..2)not-accessiblecurrent
dNSServerInternetAddressType
OBJECT-TYPE
The type of Internet address specified by the associated dNSServerInternetAddress.
1.3.6.1.4.1.17713.11.30.4.1.2INTEGER {unknown(0), ipv4(1), ipv6(2), ipv4z(3), ipv6z(4), unknown6(5), unknown7(6), unknown8(7), unknown9(8), unknown10(9), unknown11(10), unknown12(11), unknown13(12), unknown14(13), unknown15(14), unknown16(15), dns(16)}read-onlycurrent
dNSServerInternetAddress
OBJECT-TYPE
IP Address of the DNS Server which will be used to resolve hostname into IP Addresses .
1.3.6.1.4.1.17713.11.30.4.1.3InetAddressread-writecurrent
dNSServerPortNumber
OBJECT-TYPE
UDP Port Number of DNS Service on the Server.
1.3.6.1.4.1.17713.11.30.4.1.4INTEGER (2..65535)read-writecurrent
supplementary
OBJECT-IDENTITY
1.3.6.1.4.1.17713.11.96
longitude
OBJECT-TYPE
The longitude of the unit, measured in decimal degrees. This object is set by the SNMP manager and has no internal function.
1.3.6.1.4.1.17713.11.96.1DisplayString (SIZE(0..19))read-writecurrent
latitude
OBJECT-TYPE
The latitude of the unit, measured in decimal degrees. This object is set by the SNMP manager and has no internal function.
1.3.6.1.4.1.17713.11.96.2DisplayString (SIZE(0..19))read-writecurrent
altitude
OBJECT-TYPE
The altitude of the unit, measured in meters. This object is set by the SNMP manager and has no internal function.
1.3.6.1.4.1.17713.11.96.3Integer32read-writecurrent
ptpGroups
OBJECT-IDENTITY
1.3.6.1.4.1.17713.11.98
ptpTraps
OBJECT-IDENTITY
1.3.6.1.4.1.17713.11.99
ptpTrapPrefix
OBJECT-IDENTITY
1.3.6.1.4.1.17713.11.99.0

Notifications

NameOIDStatus
channelChangeTrap
NOTIFICATION-TYPE
The PTP radio has changed wireless channel. This has been caused by either i) mandatory radar avoidance, a DFS impulsive interference event will also be detected, or ii) Dynamic Spectrum Optimization, (DSO) DSO improves link performance by selecting the most appropriate transmit and receive channels with the lowest level of interference.
1.3.6.1.4.1.17713.11.99.0.1current
dfsImpulsiveInterferenceTrap
NOTIFICATION-TYPE
DFS impulsive interference detected event
1.3.6.1.4.1.17713.11.99.0.2current
mainPSUPortStatusTrap
NOTIFICATION-TYPE
Current status of the Main PSU Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert
1.3.6.1.4.1.17713.11.99.0.3current
mainPSUPortDisabledWarningTrap
NOTIFICATION-TYPE
The SNMP ifAdminStatus of the interface has disabled Ethernet traffic
1.3.6.1.4.1.17713.11.99.0.4current
mainPSUPortConfigurationMismatchTrap
NOTIFICATION-TYPE
The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch
1.3.6.1.4.1.17713.11.99.0.5current
auxPortStatusTrap
NOTIFICATION-TYPE
Current status of the Aux Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert
1.3.6.1.4.1.17713.11.99.0.6current
auxPortDisabledWarningTrap
NOTIFICATION-TYPE
The SNMP ifAdminStatus of the interface has disabled Ethernet traffic
1.3.6.1.4.1.17713.11.99.0.7current
regulatoryBandTrap
NOTIFICATION-TYPE
The Regulatory Band prohibits the wireless unit from operating outside the regulated limits. An invalid Regulatory Band may be caused by a missing or incorrect License Key, a corrupt MAC Address or an attempt to configure a Regulatory Band not allowed by the License Key or an execution of Reset Configuration. NB: a change of state may generate an SNMP trap and/or SMTP email alert.
1.3.6.1.4.1.17713.11.99.0.8current
installStatusTrap
NOTIFICATION-TYPE
A non-zero value indicates that signalling was received with the wrong MAC address or a mismatched link name. NB: It is very unusual to detect this, because units with mis-configured Target MAC Address will normally fail to establish a wireless link. However, rare circumstances may establish a partial wireless link and detect this situation. NB: A non-zero value on start-up, or a change of value during operation, may generate an SNMP trap and/or SMTP email alert
1.3.6.1.4.1.17713.11.99.0.9current
installArmStateTrap
NOTIFICATION-TYPE
Indicates if the unit is being installed. NB: a change of state may generate an SNMP trap and/or SMTP email alert
1.3.6.1.4.1.17713.11.99.0.10current
unitOutOfCalibrationTrap
NOTIFICATION-TYPE
The unit is out of calibration
1.3.6.1.4.1.17713.11.99.0.11current
auxPortPowerOverEthernetOutputStatusTrap
NOTIFICATION-TYPE
Current status of the Power Over Ethernet (PoE) output of the Aux port
1.3.6.1.4.1.17713.11.99.0.12current
incompatibleRegulatoryBandsTrap
NOTIFICATION-TYPE
The master and slave units have incompatible regulatory bands. NB: Both units must have compatible license keys
1.3.6.1.4.1.17713.11.99.0.14current
noWirelessChannelAvailableTrap
NOTIFICATION-TYPE
Spectrum Management was unable to locate a suitable wireless channel to operate on
1.3.6.1.4.1.17713.11.99.0.15current
wirelessLinkDisabledWarningTrap
NOTIFICATION-TYPE
The SNMP ifAdminStatus of the wireless interface has disabled wireless traffic
1.3.6.1.4.1.17713.11.99.0.16current
auxPortConfigurationMismatchTrap
NOTIFICATION-TYPE
The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch. This alarm is only raised if an Out-of-Band Management Mode has been configured.
1.3.6.1.4.1.17713.11.99.0.17current
sFPErrorTrap
NOTIFICATION-TYPE
If the SFP link is not OK, there are five possible causes: Either a SFP has been installed but the license key does not include SFP fiber support, a fiber link could not be established even though no LOS was detected (i.e. an optical carrier was detected, which could be due to a broken TX fiber, or because the link is disabled at the fiber link partner), a fiber link could not be established and LOS is detected (i.e. no optical carrier is detected), the installed SFP is not supported or the installed SFP failed to initialize correctly. NB: a change of status may generate an SNMP trap and/or SMTP email alert
1.3.6.1.4.1.17713.11.99.0.18current
sFPPortStatusTrap
NOTIFICATION-TYPE
Current status of the SFP Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert
1.3.6.1.4.1.17713.11.99.0.19current
incompatibleMasterAndSlaveTrap
NOTIFICATION-TYPE
A non-zero value indicates that the master and slave ends of a link are different hardware products, or have different software versions, or have different TDD Frame Configuraton Modes (Standard/Expert) in HCMP topology. NB: It is very unusual to detect this, because incompatible units will normally fail to establish a wireless link. However, some combinations may establish a partial wireless link and detect this situation. NB: A non-zero value may generate an SNMP trap and/or SMTP email alert
1.3.6.1.4.1.17713.11.99.0.20current
sNTPSyncTrap
NOTIFICATION-TYPE
If SNTP Sync fails then check the server settings in the Remote Management page, or disable SNTP
1.3.6.1.4.1.17713.11.99.0.21current
tDDSynchronizationAlarmTrap
NOTIFICATION-TYPE
Not Synchronized indicates failure of the external timing system for a period greater than the holdover timer. TDD frame timing will have drifted, and this link may cause interference with other links in a synchronized network. Timing System Failure is an early warning, indicating that 80% of the holdover period has expired.
1.3.6.1.4.1.17713.11.99.0.22current
sFPPortDisabledWarningTrap
NOTIFICATION-TYPE
The SNMP ifAdminStatus of the interface has disabled Ethernet traffic
1.3.6.1.4.1.17713.11.99.0.23current
sFPPortConfigurationMismatchTrap
NOTIFICATION-TYPE
The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch. This alarm is only raised if an Out-of-Band Management Mode has been configured.
1.3.6.1.4.1.17713.11.99.0.24current
linkModeOptimizationMismatchTrap
NOTIFICATION-TYPE
The remote node of this link has been configured with a different link mode optimization
1.3.6.1.4.1.17713.11.99.0.25current
tDMInterfaceStatusTrap
NOTIFICATION-TYPE
@Current status of the connection to the TDM Box. A state of 'Up' on a green background indicates that the TDM Box is connected OK. When connecting a TDM Box only the Main Ethernet port should be used
1.3.6.1.4.1.17713.11.99.0.26current
tDMChannelStatusTrap
NOTIFICATION-TYPE
Current status of the TDM channels. A value of 0 indicates that a TDM channel is established
1.3.6.1.4.1.17713.11.99.0.27current
tDMChannelLoopbackTrap
NOTIFICATION-TYPE
The loopback status of TDM channels. This is intended for installation testing and should be set to 'None' for normal operation. The wire connections to a unit can be tested by applying a 'Copper' loopback to the local unit. The wireless connection to the remote unit can be tested by applying a 'Wireless' loopback to the remote unit with no loopback on the local unit. NB: a change of state may generate an SNMP trap and/or SMTP email alert
1.3.6.1.4.1.17713.11.99.0.28current
nIDULanPortStatusTrap
NOTIFICATION-TYPE
Current status of the NIDU LAN Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert
1.3.6.1.4.1.17713.11.99.0.29current
syslogStateTrap
NOTIFICATION-TYPE
The syslog service has been enabled or disabled
1.3.6.1.4.1.17713.11.99.0.30current
syslogLocalNearlyFullTrap
NOTIFICATION-TYPE
The syslog local log is nearly full (90%)
1.3.6.1.4.1.17713.11.99.0.31current
syslogLocalWrappedTrap
NOTIFICATION-TYPE
The syslog local log has wrapped
1.3.6.1.4.1.17713.11.99.0.32current
syslogClientTrap
NOTIFICATION-TYPE
Enable or disable the syslog client
1.3.6.1.4.1.17713.11.99.0.33current
secureModeAlarmTrap
NOTIFICATION-TYPE
The secure mode (e.g. FIPS, UC-APL) state of the unit. The secure mode is not configured(1) state indicates that the unit is capable of secure mode operation, and one or more of the following security materials has not been configured: Key Of Keys, Private Key, Public Certificate, DRNG Entropy Status, Wireless Encryption Key. The secure mode mode is configured but not active(2) state indicates that the unit is capable of secure mode operation, and the security material has been configured, but the configuration of interfaces is not consistent with secure mode operation. The secure mode is not supported(3) state indicates that the unit is not capable of secure mode operation. The secure mode capability requires appropriate hardware compatibility, license key and software image.
1.3.6.1.4.1.17713.11.99.0.34current
dataBridgingStatusAlarmTrap
NOTIFICATION-TYPE
Ethernet Data traffic bridging is disabled because the wireless link is not operating at the configured Lowest Data Modulation Mode
1.3.6.1.4.1.17713.11.99.0.35current
licenseRemainingTrialPeriodAlarmTrap
NOTIFICATION-TYPE
If the full capability trial license period is about to expire then purchase a license upgrade from your reseller.
1.3.6.1.4.1.17713.11.99.0.36current
capacityVariantMismatchTrap
NOTIFICATION-TYPE
The remote node of this link has a lower link capacity. Operating with a reduced effective link capacity.
1.3.6.1.4.1.17713.11.99.0.37current
maxLinkRangeExceededTrap
NOTIFICATION-TYPE
The measured link range is greater than the maximum allowed by the license key. The link will operate at a reduced capacity while this condition applies. This alarm is only raised if the license specifies a maximum link range and the trial license is not active.
1.3.6.1.4.1.17713.11.99.0.38current
tDMConfigurationMismatchTrap
NOTIFICATION-TYPE
Current status of the configuration of the TDM Box. A state of 'Ok' on a green background indicates that the TDM Box configuration is matched OK with the remote end.
1.3.6.1.4.1.17713.11.99.0.39current
nIDULanPortDisabledWarningTrap
NOTIFICATION-TYPE
The SNMP ifAdminStatus of the interface has disabled Ethernet traffic
1.3.6.1.4.1.17713.11.99.0.40current
nIDULanPortConfigurationMismatchTrap
NOTIFICATION-TYPE
The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch.
1.3.6.1.4.1.17713.11.99.0.41current
portAllocationMismatchTrap
NOTIFICATION-TYPE
The local and remote ODUs have different services configured.
1.3.6.1.4.1.17713.11.99.0.44current
wirelessLinkStatusAlarmTrap
NOTIFICATION-TYPE
Current status of the wireless link. A state of Up on a green background indicates that a wireless link is established
1.3.6.1.4.1.17713.11.99.0.45current
lbtDetectedTrap
NOTIFICATION-TYPE
Listen-Before-Talk (LBT) detected event
1.3.6.1.4.1.17713.11.99.0.46current
secureLicenseSignatureAlarmTrap
NOTIFICATION-TYPE
Alarm condition indicates that the unit's license is not secure enough for FIPS approved mode.
1.3.6.1.4.1.17713.11.99.0.47current

Conformance

NameOIDStatus
ptpCompliance
MODULE-COMPLIANCE
The compliance statement for the Cambium PTP MIB
1.3.6.1.4.1.17713.11.97current
dfsGroup
OBJECT-GROUP
The dfs object group.
1.3.6.1.4.1.17713.11.98.3current
bridgeGroup
OBJECT-GROUP
The bridge object group.
1.3.6.1.4.1.17713.11.98.4current
configurationGroup
OBJECT-GROUP
The configuration object group.
1.3.6.1.4.1.17713.11.98.5current
ethernetGroup
OBJECT-GROUP
The ethernet object group.
1.3.6.1.4.1.17713.11.98.6current
tDMGroup
OBJECT-GROUP
The tDM object group.
1.3.6.1.4.1.17713.11.98.7current
licenseGroup
OBJECT-GROUP
The license object group.
1.3.6.1.4.1.17713.11.98.8current
managementGroup
OBJECT-GROUP
The management object group.
1.3.6.1.4.1.17713.11.98.9current
phyControlGroup
OBJECT-GROUP
The phyControl object group.
1.3.6.1.4.1.17713.11.98.10current
phyStatusGroup
OBJECT-GROUP
The phyStatus object group.
1.3.6.1.4.1.17713.11.98.12current
alarmsGroup
OBJECT-GROUP
The alarms object group.
1.3.6.1.4.1.17713.11.98.13current
apcGroup
OBJECT-GROUP
The apc object group.
1.3.6.1.4.1.17713.11.98.14current
smtpGroup
OBJECT-GROUP
The smtp object group.
1.3.6.1.4.1.17713.11.98.15current
snmpControlGroup
OBJECT-GROUP
The snmpControl object group.
1.3.6.1.4.1.17713.11.98.16current
sntpGroup
OBJECT-GROUP
The sntp object group.
1.3.6.1.4.1.17713.11.98.17current
resetGroup
OBJECT-GROUP
The reset object group.
1.3.6.1.4.1.17713.11.98.18current
versionsGroup
OBJECT-GROUP
The versions object group.
1.3.6.1.4.1.17713.11.98.19current
pubStatsGroup
OBJECT-GROUP
The pubStats object group.
1.3.6.1.4.1.17713.11.98.20current
encryptionGroup
OBJECT-GROUP
The encryption object group.
1.3.6.1.4.1.17713.11.98.22current
tDDControlGroup
OBJECT-GROUP
The tDDControl object group.
1.3.6.1.4.1.17713.11.98.23current
syslogControlGroup
OBJECT-GROUP
The syslogControl object group.
1.3.6.1.4.1.17713.11.98.24current
aAAControlGroup
OBJECT-GROUP
The aAAControl object group.
1.3.6.1.4.1.17713.11.98.25current
routerProtocolsGroup
OBJECT-GROUP
The routerProtocols object group.
1.3.6.1.4.1.17713.11.98.26current
cableDiagnosticsGroup
OBJECT-GROUP
The cableDiagnostics object group.
1.3.6.1.4.1.17713.11.98.27current
unitIdentificationGroup
OBJECT-GROUP
The unitIdentification object group.
1.3.6.1.4.1.17713.11.98.28current
authorizationControlGroup
OBJECT-GROUP
The authorizationControl object group.
1.3.6.1.4.1.17713.11.98.29current
dNSGroup
OBJECT-GROUP
The dNS object group.
1.3.6.1.4.1.17713.11.98.30current
supplementaryGroup
OBJECT-GROUP
The supplementary object group.
1.3.6.1.4.1.17713.11.98.96current
notificationsGroup
NOTIFICATION-GROUP
The notifications group.
1.3.6.1.4.1.17713.11.98.99current