MIBs Depot

CAMBIUM-PTP500-MIB

Registered at
1.3.6.1.4.1.17713.5
Last updated
2014-03-14 16:04
Organization
Cambium Networks Ltd.
Revisions
2014-03-14 16:04, 2013-02-08 08:38, 2012-07-09 17:50, 2012-03-28 10:37, 2011-07-13 16:57, 2010-09-22 14:49, 2009-05-29 09:25, 2008-11-04 10:22, 2008-06-26 16:44, 2008-04-11 18:08
Namespace
cambium
Source file
CAMBIUM-PTP500-MIB
Digest
sha256:c4bacc38e323d2ab931f92a9e0d2e1f12edcd03e5e0432aefc704f70b9249822

Description

MIB for 105Mbps non-line-of-sight (NLOS) wireless ethernet bridge.

Contact

Post: Simon Whitaker Cambium Networks Ltd. Unit B2, Linhay Business Park, Eastern Road, Ashburton, Devon. TQ13 7UP United Kingdom Phone: +44 (0) 1364 655 500 Email: simon.whitaker@cambiumnetworks.com

Imports

FromSymbols
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP
SNMPv2-SMIInteger32, IpAddress, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, enterprises, iso
SNMPv2-TCDisplayString, TEXTUAL-CONVENTION

Imported by

Nothing in this corpus imports this module.

Load order

Every file a consumer needs in order to load this module, dependencies first.

CAMBIUM-PTP500-MIB
SNMPv2-CONF
SNMPv2-SMI
SNMPv2-TC

Objects

NameOIDSyntaxAccessStatus
ptp
OBJECT-IDENTITY
1.3.6.1.4.1.17713.1
ptmp
OBJECT-IDENTITY
1.3.6.1.4.1.17713.2
ptp500
OBJECT-IDENTITY
1.3.6.1.4.1.17713.5
dfs
OBJECT-IDENTITY
1.3.6.1.4.1.17713.5.3
dfsTableNumber
OBJECT-TYPE
Number of entries in the dfsTable
1.3.6.1.4.1.17713.5.3.1INTEGER (1..63)read-onlycurrent
dfsTable
OBJECT-TYPE
A table storing a snapshot of various DFS measurements for each channel
1.3.6.1.4.1.17713.5.3.2not-accessiblecurrent
dfsTableEntry
OBJECT-TYPE
Table DfsTable
1.3.6.1.4.1.17713.5.3.2.1not-accessiblecurrent
dfsTableIndex
OBJECT-TYPE
used to index values in the dfsTable.
1.3.6.1.4.1.17713.5.3.2.1.1INTEGER (1..63)not-accessiblecurrent
dfsMeans
OBJECT-TYPE
Snapshot of DFS means
1.3.6.1.4.1.17713.5.3.2.1.2Integer32read-onlycurrent
dfsNineNinePointNinePercentiles
OBJECT-TYPE
Snapshot of DFS 99.9 percentiles
1.3.6.1.4.1.17713.5.3.2.1.3Integer32read-onlycurrent
dfsPeaks
OBJECT-TYPE
Snapshot of DFS peaks
1.3.6.1.4.1.17713.5.3.2.1.4Integer32read-onlycurrent
configuration
OBJECT-IDENTITY
1.3.6.1.4.1.17713.5.5
iPAddress
OBJECT-TYPE
Internet protocol (IP) address. This address is used by the family of Internet protocols to uniquely identify the unit on a network. NB: A system reboot is required to activate changes to this attribute.
1.3.6.1.4.1.17713.5.5.1IpAddressread-writecurrent
subnetMask
OBJECT-TYPE
A subnet allows the flow of network traffic between hosts to be segregated based on a network configuration. By organizing hosts into logical groups, subnetting can improve network security and performance. NB: A system reboot is required to activate changes to this attribute
1.3.6.1.4.1.17713.5.5.2IpAddressread-writecurrent
gatewayIPAddress
OBJECT-TYPE
The IP address of a computer on the current network that is currently acting as a network gateway. A gateway acts as an entrance / exit to packets from / to other networks. NB: A system reboot is required to activate changes to this attribute
1.3.6.1.4.1.17713.5.5.3IpAddressread-writecurrent
targetMACAddress
OBJECT-TYPE
MAC address of the PTP wireless unit forming the other end of the PTP link
1.3.6.1.4.1.17713.5.5.4OCTET STRING (SIZE(6))read-onlycurrent
masterSlaveMode
OBJECT-TYPE
The PTP wireless link operates using a master and slave relationship
1.3.6.1.4.1.17713.5.5.5INTEGER {master(0), slave(1)}read-onlycurrent
maximumTransmitPower
OBJECT-TYPE
Maximum transmit power the wireless unit is permitted to use when establishing and maintaining the wireless link
1.3.6.1.4.1.17713.5.5.6INTEGER (-100..27)read-onlycurrent
antennaGain
OBJECT-TYPE
Antenna Gain. Expressed in 10ths of dBi. NB: This attribute is ignored for variants with an integral antenna.
1.3.6.1.4.1.17713.5.5.7INTEGER (0..610)read-writecurrent
cableLoss
OBJECT-TYPE
Loss in the cable between the ODU and the antenna. Expressed in 10ths of dB. NB: This attribute is ignored for variants with an integral antenna.
1.3.6.1.4.1.17713.5.5.8INTEGER (0..255)read-writecurrent
eIRP
OBJECT-TYPE
Effective Isotropic Radiated Power (EIRP) describes the strength of the radio signal leaving the wireless unit. Expressed in 10ths of dBm
1.3.6.1.4.1.17713.5.5.9Integer32read-onlycurrent
channelBandwidth
OBJECT-TYPE
This control sets the bandwidth of the transmit and receive radio channels
1.3.6.1.4.1.17713.5.5.11INTEGER {bw30MHz(0), bw15MHz(1), bw10MHz(2), bw5MHz(3), bw20MHz(4)}read-onlycurrent
remoteIPAddress
OBJECT-TYPE
IP Address of the peer wireless unit
1.3.6.1.4.1.17713.5.5.12IpAddressread-onlycurrent
linkName
OBJECT-TYPE
Name of the PTP link allocated by the System Administrator. Used to establish a connection with the correct PTP wireless unit at the other end of the link. NOTE: The link name MUST be the same at both ends of the PTP link.
1.3.6.1.4.1.17713.5.5.14DisplayString (SIZE(0..63))read-onlycurrent
siteName
OBJECT-TYPE
This field contains a user-provided description of the site name together with any additional notes
1.3.6.1.4.1.17713.5.5.15DisplayString (SIZE(0..63))read-writecurrent
accessMethod
OBJECT-TYPE
This controls whether the link can be established between pre-paired Master-Slave using MAC addresses (Link Access) or by using link name (Link Name Access)
1.3.6.1.4.1.17713.5.5.16INTEGER {linkAccess(0), linkNameAccess(1), groupAccess(2)}read-onlycurrent
groupID
OBJECT-TYPE
When Access Method is set to Group Access, the Group ID identifies all the units belonging to the same group. Group Access is only supported on some platforms
1.3.6.1.4.1.17713.5.5.17INTEGER (0..255)read-onlycurrent
ethernet
OBJECT-IDENTITY
1.3.6.1.4.1.17713.5.6
dataPortAutoNegotiation
OBJECT-TYPE
This controls whether the local Ethernet interface configuration is automatically negotiated or forced. Do not use a forced setting together with auto negotiation at the Ethernet link partner. If you want to run your Ethernet link at a fixed speed and duplex then you would normally leave auto negotiation enabled and only enable the single Auto Neg Advertisement option that you want the link to run in - FORCING ETHERNET CONFIGURATION IS A LAST RESORT WHICH SHOULD ONLY BE PERFORMED IF YOU ARE HAVING PROBLEMS WITH AUTO NEGOTIATION - AND YOU MUST ENSURE THAT YOU CONFIGURE BOTH THIS UNIT AND THE ETHERNET LINK PARTNER TO WHICH IT IS CONNECTED IDENTICALLY (THE LINK PARTNER MUST NOT HAVE AUTO NEGOTIATION ENABLED EITHER, OTHERWISE A DUPLEX MISMATCH WILL OCCUR). NB: The new setting will only take effect after a system reboot.
1.3.6.1.4.1.17713.5.6.1INTEGER {disabled(0), enabled(1)}read-writecurrent
dataPortAutoNegAdvertisement
OBJECT-TYPE
This sets the different Ethernet configurations that will be advertised during auto negotiation. NB: The new setting will only take effect after a system reboot. WARNING: Duplex mismatch may result if both ends of the Ethernet link do not have the same settings. Do not auto negotiation together with a fixed setting at the Ethernet link partner. WARNING: Make sure that you select option(s) that you know your connected equipment can cater for!
1.3.6.1.4.1.17713.5.6.2Bits {negInvalid(2), neg10MbpsHalfDuplex(3), neg10MbpsFullDuplex(4), neg100MbpsHalfDuplex(5), neg100MbpsFullDuplex(6), negUnknown1(7)}read-writecurrent
dataPortAutoMdix
OBJECT-TYPE
This enables/disables the Auto MDI/MDIX capability. NB: The new setting will only take effect after a system reboot
1.3.6.1.4.1.17713.5.6.3INTEGER {disabled(0), enabled(1)}read-writecurrent
dataPortStatus
OBJECT-TYPE
Current status of the Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert
1.3.6.1.4.1.17713.5.6.4INTEGER {down(0), copperLinkUp(1), fiberLinkUp(2)}read-onlycurrent
dataPortSpeedAndDuplex
OBJECT-TYPE
The current speed and duplex of the Ethernet link
1.3.6.1.4.1.17713.5.6.5INTEGER {speed1000MbpsFullDuplex(0), speed100MbpsFullDuplex(1), speed100MbpsHalfDuplex(2), speed10MbpsFullDuplex(3), speed10MbpsHalfDuplex(4), speedUnknown6(5)}read-onlycurrent
dataPortWirelessDownAlert
OBJECT-TYPE
When enabled, this causes the Ethernet link to be dropped briefly when the wireless link drops. This is so that spanning tree algorithms can quickly detect that there is a problem.
1.3.6.1.4.1.17713.5.6.6INTEGER {disabled(0), enabled(1)}read-writecurrent
useVLANForManagementInterfaces
OBJECT-TYPE
This controls whether the management interfaces (WWW/SNMP/SMTP/SNTP) use VLAN tags or not. NB: The new setting will only take effect after a system reboot
1.3.6.1.4.1.17713.5.6.7INTEGER {noVLANTagging(0), iEEE8021QTaggedCTagType8100(1), iEEE8021adTaggedSTagorBTagType88a8(2)}read-writecurrent
vLANManagementPriority
OBJECT-TYPE
This VLAN Priority (0-7) will be included in packets generated by the management interfaces. NB: The new setting will only take effect after a system reboot
1.3.6.1.4.1.17713.5.6.8INTEGER (0..7)read-writecurrent
vLANManagementVID
OBJECT-TYPE
This VLAN VID (0-4094) will be included in packets generated by the management interfaces. NB: The new setting will only take effect after a system reboot
1.3.6.1.4.1.17713.5.6.11INTEGER (0..4094)read-writecurrent
vLANPriorityTableNumber
OBJECT-TYPE
Number of entries in the vLANPriorityTable.
1.3.6.1.4.1.17713.5.6.14INTEGER (9)read-onlycurrent
vLANPriorityTable
OBJECT-TYPE
A priority queue mapping table. This is a list of packet queues indexed by VLAN priority.
1.3.6.1.4.1.17713.5.6.15not-accessiblecurrent
vLANPriorityTableEntry
OBJECT-TYPE
Table VLANPriorityTable
1.3.6.1.4.1.17713.5.6.15.1not-accessiblecurrent
vLANPriorityQueueMapping
OBJECT-TYPE
Mapping of VLAN priority flag to packet queue. The higher the queue number the greater its priority.
1.3.6.1.4.1.17713.5.6.15.1.1INTEGER {q0(0), q1(1), q2(2), q3(3), q4(4), q5(5), q6(6), q7(7)}read-writecurrent
vLANPriorityTableIndex
OBJECT-TYPE
VLAN priority flag, used to index values in the vLANPriorityTable.
1.3.6.1.4.1.17713.5.6.15.1.2INTEGER {p0(1), p1(2), p2(3), p3(4), p4(5), p5(6), p6(7), p7(8), untagged(9)}not-accessiblecurrent
telecom
OBJECT-IDENTITY
1.3.6.1.4.1.17713.5.7
telecomsInterface
OBJECT-TYPE
The line interface type. If this is set to 'None' then the telecoms interfaces are disabled, and the telecom group attributes will be ignored.
1.3.6.1.4.1.17713.5.7.1INTEGER {none(0), e1(1), t1(2)}read-onlycurrent
telecomsChannelStatus
OBJECT-TYPE
Current status of telecoms channel. NB: a change of state may generate an SNMP trap and/or SMTP email alert
1.3.6.1.4.1.17713.5.7.2INTEGER {disabled(0), noSignalLocal(1), noSignalRemote(2), noSignalLocalandRemote(3), up(4), remoteTiming(5), noSignalLocalandRemoteTiming(6)}read-onlycurrent
telecomsLineCode
OBJECT-TYPE
The line code setting of the telecoms interface. This must match the setting of the device connected to this interface
1.3.6.1.4.1.17713.5.7.4INTEGER {aMI(0), b8ZSHDB3(1)}read-onlycurrent
telecomsCableLength
OBJECT-TYPE
The length of the cable connected to the telecoms interface, measured in feet
1.3.6.1.4.1.17713.5.7.6INTEGER {feet133(0), feet266(1), feet399(2), feet533(3), feet655(4)}read-onlycurrent
telecomsLoopback
OBJECT-TYPE
The loopback status of telecoms channel. This is intended for installation testing and should be set to 'None' for normal operation. The wire connections to a unit can be tested by applying a 'Copper' loopback to the local unit. The wireless connection to the remote unit can be tested by applying a 'Wireless' loopback to the remote unit with no loopback on the local unit. When applying a wireless loopback, please ensure that the other end of the link has a loopback setting of 'None'. NB: a change of state may generate an SNMP trap and/or SMTP email alert
1.3.6.1.4.1.17713.5.7.8INTEGER {none(0), copper(1), wireless(2)}read-onlycurrent
licence
OBJECT-IDENTITY
1.3.6.1.4.1.17713.5.8
regionCode
OBJECT-TYPE
The region code prohibits the wireless unit from operating outside the regulated limits. An invalid region code indicates a corrupted licence key. NB: a change of state may generate an SNMP trap and/or SMTP email alert
1.3.6.1.4.1.17713.5.8.1INTEGER {regionCodeInvalid(0), regionCode1(1), regionCode2(2), regionCode3(3), regionCode4(4), regionCode5(5), regionCode6(6), regionCode7(7), regionCode8(8), regionCode9(9), regionCode10(10), regionCode11(11), regionCode12(12), regionCode13(13), regionCode14(14), regionCode15(15), regionCode16(16), regionCode17(17), regionCode18(18), regionCode19(19), regionCode20(20), regionCode21(21), regionCode22(22), regionCode23(23), regionCode24(24), regionCode25(25), regionCode26(26), regionCode27(27), regionCode28(28), regionCode29(29), regionCode30(30), regionCode31(31)}read-onlycurrent
productVariant
OBJECT-TYPE
The product variant
1.3.6.1.4.1.17713.5.8.2INTEGER {pTPxx400Full(0), pTPxx400Deprecated1(1), pTPxx400Deprecated2(2), pTPxx400Lite(3), spare1(4), pTPxx300(5), spare2(6), spare3(7), pTPxx500FullDeprecated(8), pTPxx500LiteDeprecated(9), pTPxx500(10), pTPxx600Lite(11), pTPxx600Full(12), spare5(13), spare6(14), pTP800(15)}read-onlycurrent
productName
OBJECT-TYPE
Name of the product variant
1.3.6.1.4.1.17713.5.8.3DisplayString (SIZE(0..63))read-onlycurrent
ethernetFiberSupport
OBJECT-TYPE
Ethernet fiber support availability on this wireless unit
1.3.6.1.4.1.17713.5.8.4INTEGER {disabled(0), enabled(1)}read-onlycurrent
frequencyVariant
OBJECT-TYPE
Frequency variant of the wireless unit
1.3.6.1.4.1.17713.5.8.5INTEGER {freq5800MHz(0), freq5400MHz(1), freq4900MHz(2), freq2500MHz(3), freq5800MHz2(4), freq5400MHz2(5), freq4500MHz(6), freq5900MHz(7), freq5200MHz(8), freq5100MHz(9), freq4800MHz(10)}read-onlycurrent
bandwidthVariant
OBJECT-TYPE
Bandwidth variant of the wireless unit
1.3.6.1.4.1.17713.5.8.6INTEGER {bw30MHz(0), bw15MHz(1), bw10MHz(2), bw5MHz(3), bw20MHz(4)}read-onlycurrent
constantPowerSpectralDensity
OBJECT-TYPE
Constant power spectral density mode control
1.3.6.1.4.1.17713.5.8.7INTEGER {constant(0), fullPower(1)}read-onlycurrent
sNMPv3Enable
OBJECT-TYPE
SNMPv3 availability control
1.3.6.1.4.1.17713.5.8.9INTEGER {disabled(0), enabled(1)}read-onlycurrent
licensedCapacity
OBJECT-TYPE
Maximum allowable data rate for ethernet frames permitted by the licence key. The actual data rate depends upon the prevailing wireless conditions
1.3.6.1.4.1.17713.5.8.11INTEGER {capacity25Mbps(0), capacity52Mbps(1), capacity105Mbps(2)}read-onlycurrent
management
OBJECT-IDENTITY
1.3.6.1.4.1.17713.5.9
installStatus
OBJECT-TYPE
A non-zero value indicates that signalling was received with the wrong MAC address or a mismatched link name. NB: It is very unusual to detect this, because units with mis-configured Target MAC Address will normally fail to establish a wireless link. However, rare circumstances may establish a partial wireless link and detect this situation. NB: A non-zero value on start-up, or a change of value during operation, may generate an SNMP trap and/or SMTP email alert
1.3.6.1.4.1.17713.5.9.3INTEGER {ok(0), wrongPeer(1)}read-onlycurrent
installArmState
OBJECT-TYPE
Indicates if the unit is being installed. NB: a value other than 'disarmed' on startup, or a change of state during operation may generate an SNMP trap and/or SMTP email alert
1.3.6.1.4.1.17713.5.9.4INTEGER {disarmed(0), armed(1)}read-onlycurrent
tFTPServerIPAddress
OBJECT-TYPE
IP address of the TFTP Server from which the TFTP Software Upgrade File Name will be retrieved
1.3.6.1.4.1.17713.5.9.5IpAddressread-writecurrent
tFTPServerPortNumber
OBJECT-TYPE
The port number of the TFTP Server from which the TFTP Software Upgrade File Name will be retrieved
1.3.6.1.4.1.17713.5.9.6INTEGER (0..65535)read-writecurrent
tFTPSoftwareUpgradeFileName
OBJECT-TYPE
Filename of the Software Upgrade to be loaded from the TFTP Server
1.3.6.1.4.1.17713.5.9.7DisplayString (SIZE(0..127))read-writecurrent
tFTPStartSoftwareUpgrade
OBJECT-TYPE
Write '1' to this attribute to start the TFTP software upgrade process. The attribute will be reset to 0 when the upgrade process has finished
1.3.6.1.4.1.17713.5.9.8Integer32read-writecurrent
tFTPSoftwareUpgradeStatus
OBJECT-TYPE
The current status of the TFTP Software upgrade process
1.3.6.1.4.1.17713.5.9.9INTEGER {idle(0), uploadinprogress(1), uploadsuccessfulprogrammingFLASH(2), upgradesuccessfulreboottorunthenewsoftwareimage(3), upgradefailed(4)}read-onlycurrent
tFTPSoftwareUpgradeStatusText
OBJECT-TYPE
Descriptive text describing the status of the TFTP Software upgrade process, including any error details
1.3.6.1.4.1.17713.5.9.10DisplayString (SIZE(0..127))read-onlycurrent
tFTPSoftwareUpgradeStatusAdditionalText
OBJECT-TYPE
Any additional text describing the status of the TFTP Software upgrade process, including any error details
1.3.6.1.4.1.17713.5.9.11DisplayString (SIZE(0..127))read-onlycurrent
hTTPAccessEnabled
OBJECT-TYPE
This controls whether or not HTTP access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the HTTP port. Remote management via HTTPS is not affected by this setting. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = Enabled)
1.3.6.1.4.1.17713.5.9.12INTEGER {no(0), yes(1)}read-writecurrent
telnetAccessEnabled
OBJECT-TYPE
This controls whether or not Telnet access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the TELNET port. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = Disabled)
1.3.6.1.4.1.17713.5.9.13INTEGER {no(0), yes(1)}read-writecurrent
hTTPPortNumber
OBJECT-TYPE
This controls the port number for HTTP access. A value of zero will use the default port number. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = 80)
1.3.6.1.4.1.17713.5.9.14INTEGER (0..65535)read-writecurrent
hTTPSPortNumber
OBJECT-TYPE
This controls the port number for HTTPS access. A value of zero will use the default port number. Availability of HTTPS is controlled via the Licence Key. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = 443)
1.3.6.1.4.1.17713.5.9.15INTEGER (0..65535)read-writecurrent
telnetPortNumber
OBJECT-TYPE
This controls the port number for TELNET access. A value of zero will use the default port number. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = 23)
1.3.6.1.4.1.17713.5.9.16INTEGER (0..65535)read-writecurrent
hTTPSAccessEnabled
OBJECT-TYPE
This controls whether or not HTTPS access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the HTTPS port. Remote management via HTTP is not affected by this setting. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = Enabled)
1.3.6.1.4.1.17713.5.9.17INTEGER {no(0), yes(1)}read-writecurrent
phyControl
OBJECT-IDENTITY
1.3.6.1.4.1.17713.5.10
linkSymmetry
OBJECT-TYPE
In fixed asymmetric mode (3 to 1) the transmit time is three times as long as the receive time. In fixed symmetric mode (1 to 1) the unit spends an equal amount of time transmitting and receiving. In fixed asymmetric mode (1 to 3) the receive time is three times as long as the transmit time. In adaptive mode the transmit and receive periods adjust with applied load. NB: only applicable for master nodes.
1.3.6.1.4.1.17713.5.10.1INTEGER {symmetryAdaptive(0), symmetry3to1(1), symmetry1to1(2), symmetry1to3(3)}read-onlycurrent
linkModeOptimisation
OBJECT-TYPE
Optimises the wireless link behavior for the type of traffic to be carried. In 'IP Traffic' mode, the wireless link will minimise transmission errors by automatically adapting the modulation mode. In 'TDM Traffic' mode, the wireless link will minimise transmission latency and preserve throughput by maintaining a higher modulation mode in the presence of a limited number of errors. The 'TDM Traffic' mode is recommended for E1/T1 applications and connectionless protocols.
1.3.6.1.4.1.17713.5.10.2INTEGER {iPTraffic(0), tDMTraffic(1)}read-onlycurrent
userConfiguredMaxModulationMode
OBJECT-TYPE
The maximum receive modulation mode controls the MAX mode used for adaptive modulation. NOTE: This attribute is automatically disabled when the installation agent is armed. To disarm the installation agent use the installation wizard
1.3.6.1.4.1.17713.5.10.3INTEGER {modBpsk50percent(0), modQpsk50percent(1), modQpsk75percent(2), mod16qam50percent(3), mod16qam75percent(4), mod64qam67percent(5), mod64qam83percent(6)}read-writecurrent
remoteMaximumTransmitPower
OBJECT-TYPE
Maximum transmit power the remote wireless unit is permitted to use when establishing and maintaining the wireless link
1.3.6.1.4.1.17713.5.10.4INTEGER (-100..27)read-onlycurrent
phyStatus
OBJECT-IDENTITY
1.3.6.1.4.1.17713.5.12
receivePower
OBJECT-TYPE
Receive power expressed in tenths of a dBm
1.3.6.1.4.1.17713.5.12.1Integer32read-onlycurrent
vectorError
OBJECT-TYPE
The vector error measurement compares the received signal's IQ modulation characteristics to an ideal signal to determine the composite error vector magnitude. The value represented by this attribute is the average vector error over the previous second expressed in tenths of a dB
1.3.6.1.4.1.17713.5.12.2Integer32read-onlycurrent
transmitPower
OBJECT-TYPE
Transmit power expressed in tenths of a dBm
1.3.6.1.4.1.17713.5.12.3Integer32read-onlycurrent
range
OBJECT-TYPE
Distance between the two peer wireless units expressed in tenths of a kilometer
1.3.6.1.4.1.17713.5.12.4Integer32read-onlycurrent
linkLoss
OBJECT-TYPE
The wireless link loss expressed in tenths of a dB
1.3.6.1.4.1.17713.5.12.5INTEGER (-500..500)read-onlycurrent
receiveChannel
OBJECT-TYPE
Current active receive channel
1.3.6.1.4.1.17713.5.12.6INTEGER (0..63)read-onlycurrent
transmitChannel
OBJECT-TYPE
Current active transmit channel
1.3.6.1.4.1.17713.5.12.7INTEGER (0..63)read-onlycurrent
receiveModulationMode
OBJECT-TYPE
Current active receive modulation mode
1.3.6.1.4.1.17713.5.12.8INTEGER {modAcquisition(0), modBpsk50percent(1), modQpsk50percentSingle(2), modQpsk75percentSingle(3), mod16qam50percentSingle(4), mod16qam75percentSingle(5), mod64qam67percentSingle(6), mod64qam83percentSingle(7), modReserved1(8), modQpsk50percentDual(9), modQpsk75percentDual(10), mod16qam50percentDual(11), mod16qam75percentDual(12), mod64qam67percentDual(13), mod64qam83percentDual(14), modReserved2(15)}read-onlycurrent
transmitModulationMode
OBJECT-TYPE
Current active transmit modulation mode
1.3.6.1.4.1.17713.5.12.9INTEGER {modAcquisition(0), modBpsk50percent(1), modQpsk50percentSingle(2), modQpsk75percentSingle(3), mod16qam50percentSingle(4), mod16qam75percentSingle(5), mod64qam67percentSingle(6), mod64qam83percentSingle(7), modReserved1(8), modQpsk50percentDual(9), modQpsk75percentDual(10), mod16qam50percentDual(11), mod16qam75percentDual(12), mod64qam67percentDual(13), mod64qam83percentDual(14), modReserved2(15)}read-onlycurrent
receiveFreqMHz
OBJECT-TYPE
Current receive frequency expressed in integer MHz
1.3.6.1.4.1.17713.5.12.11INTEGER (0..5925)read-onlycurrent
transmitFreqMHz
OBJECT-TYPE
Current transmit frequency expressed in integer MHz
1.3.6.1.4.1.17713.5.12.12INTEGER (0..5925)read-onlycurrent
signalStrengthRatio
OBJECT-TYPE
Signal strength ratio (Vertical / Horizontal) : the number of dB larger the Vertical antenna input is than the Horizontal antenna input expressed in tenths of a dB
1.3.6.1.4.1.17713.5.12.13Integer32read-onlycurrent
receiveFreqKHz
OBJECT-TYPE
Current receive frequency expressed as KHz
1.3.6.1.4.1.17713.5.12.14INTEGER (0..5925000)read-onlycurrent
transmitFreqKHz
OBJECT-TYPE
Current transmit frequency expressed as KHz
1.3.6.1.4.1.17713.5.12.15INTEGER (0..5925000)read-onlycurrent
searchState
OBJECT-TYPE
Search status of the wireless modem. 'Registering' means that the modem has locked to an OFDM signal, and the wireless link is up. 'Searching' means that no wireless signal has been detected. 'Acquiring' means that a wireless signal has been detected, but the modem has not locked to an OFDM signal.
1.3.6.1.4.1.17713.5.12.16INTEGER {registering(0), searching(1), acquiring(2), registeringAcquiring2(3)}read-onlycurrent
alarms
OBJECT-IDENTITY
1.3.6.1.4.1.17713.5.13
unitOutOfCalibration
OBJECT-TYPE
The unit is out of calibration
1.3.6.1.4.1.17713.5.13.1INTEGER {calibrated(0), partialCalibration(1), invalidCalibration(2), bandwidthvariantunsupportedPAsShutdown(3), outOfCalibrationPAsShutdown(4)}read-onlycurrent
incompatibleRegionCodes
OBJECT-TYPE
The master and slave units have incompatible region codes. NB: Both units must have compatible licence keys
1.3.6.1.4.1.17713.5.13.4INTEGER {ok(0), incompatibleLicenceKeys(1)}read-onlycurrent
noWirelessChannelAvailable
OBJECT-TYPE
Spectrum Management was unable to locate a suitable wireless channel to operate on
1.3.6.1.4.1.17713.5.13.5INTEGER {ok(0), noWirelessChannelAvailable(1)}read-onlycurrent
wirelessLinkDisabledWarning
OBJECT-TYPE
The SNMP ifAdminStatus of the wireless interface has disabled wireless traffic
1.3.6.1.4.1.17713.5.13.6INTEGER {ok(0), disabledBySNMPifAdminStatus(1)}read-onlycurrent
dataPortDisabledWarning
OBJECT-TYPE
The SNMP ifAdminStatus of the Ethernet interface has disabled Ethernet traffic
1.3.6.1.4.1.17713.5.13.7INTEGER {ok(0), disabledBySNMPifAdminStatus(1)}read-onlycurrent
dataPortConfigurationMismatch
OBJECT-TYPE
The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch
1.3.6.1.4.1.17713.5.13.9INTEGER {noError(0), mismatchDetected(1)}read-onlycurrent
incompatibleMasterAndSlave
OBJECT-TYPE
A non-zero value indicates that the master and slave ends of a link are different hardware products, or have different software versions. NB: It is very unusual to detect this, because incompatible units will normally fail to establish a wireless link. However, some combinations may establish a partial wireless link and detect this situation. NB: A non-zero value may generate an SNMP trap and/or SMTP email alert
1.3.6.1.4.1.17713.5.13.10INTEGER {ok(0), incompatibleProductVariants(1), differentSoftwareVersionsRunning(2)}read-onlycurrent
tDDSynchronizationStatus
OBJECT-TYPE
An alarm value (displayed in red) indicates that one of the following conditions has not been met (i) An external timing system is connected or internal timing has been configured. (ii) The timing system is providing a useable reference. (iii) The ODU is locked to this reference.
1.3.6.1.4.1.17713.5.13.11INTEGER {locked(0), holdover(1), holdoverNotConnected(2), acquiringLock(3), noTimingReference(4), timingSystemNotConnected(5), initialising(6), clusterTimingMaster(7), tDDSyncNotActive(8)}read-onlycurrent
tDDSynchronizationAlarm
OBJECT-TYPE
Not Synchronized indicates failure of the external timing system for a period greater than the holdover timer. TDD frame timing will have drifted, and this link may cause interference with other links in a synchronized network. Timing System Failure is an early warning, indicating that 80% of the holdover period has expired.
1.3.6.1.4.1.17713.5.13.13INTEGER {ok(0), notSynchronized(1), timingSystemFailure(2)}read-onlycurrent
linkModeOptimizationMismatch
OBJECT-TYPE
The remote node of this link has been configured with a different link mode optimization
1.3.6.1.4.1.17713.5.13.14INTEGER {ok(0), linkModeOptimizationMismatch(1)}read-onlycurrent
capacityLicenseMismatch
OBJECT-TYPE
The local and remote units have different licensed capacity and/or the full capacity trial has been activated at only one unit. The wireless link is operating at the capacity of the lowest capacity unit
1.3.6.1.4.1.17713.5.13.16INTEGER {ok(0), mismatchDetected(1)}read-onlycurrent
smtp
OBJECT-IDENTITY
1.3.6.1.4.1.17713.5.15
sMTPEmailAlert
OBJECT-TYPE
Simple Mail Transfer Protocol is used to send equipment alerts via email to a specified email address. This utility can only be configured by the system administrator
1.3.6.1.4.1.17713.5.15.1INTEGER {disabled(0), enabled(1)}read-writecurrent
sMTPServerIPAddress
OBJECT-TYPE
IP address of the SMTP server
1.3.6.1.4.1.17713.5.15.2IpAddressread-writecurrent
sMTPServerPortNumber
OBJECT-TYPE
Port number of the SMTP server
1.3.6.1.4.1.17713.5.15.3INTEGER (0..65535)read-writecurrent
sMTPSourceEmailAddress
OBJECT-TYPE
The 'from' email address used when constructing the automatically generated e-mail message
1.3.6.1.4.1.17713.5.15.4DisplayString (SIZE(0..63))read-writecurrent
sMTPDestinationEmailAddress
OBJECT-TYPE
The 'to' email address used when constructing the automatically generated e-mail message
1.3.6.1.4.1.17713.5.15.5DisplayString (SIZE(0..63))read-writecurrent
sMTPEnabledMessages
OBJECT-TYPE
This controls which SMTP messages the unit will send
1.3.6.1.4.1.17713.5.15.6Bits {telecomsChannelUpDown(1), unknown6(2), dataPortUpDown(3), enabledDiagnosticAlarms(4), dFSImpulseInterference(5), channelChange(6), wirelessLinkUpDown(7)}read-writecurrent
snmpControl
OBJECT-IDENTITY
1.3.6.1.4.1.17713.5.16
sNMPPortNumber
OBJECT-TYPE
The IP port number used to access the SNMP MIB (i.e. Gets and Sets) (default = 161). NB: A system reboot is required to activate changes to this attribute
1.3.6.1.4.1.17713.5.16.1INTEGER (0..65535)read-writecurrent
sNMPCommunityString
OBJECT-TYPE
The SNMP community string. NB: A system reboot is required to activate changes to this attribute
1.3.6.1.4.1.17713.5.16.2DisplayString (SIZE(0..63))read-writecurrent
sNMPTrapTableNumber
OBJECT-TYPE
Number of entries in the sNMPTrapTable.
1.3.6.1.4.1.17713.5.16.3INTEGER (2)read-onlycurrent
sNMPTrapTable
OBJECT-TYPE
SNMP trap configuration table.
1.3.6.1.4.1.17713.5.16.4not-accessiblecurrent
sNMPTrapTableEntry
OBJECT-TYPE
Table SNMPTrapTable
1.3.6.1.4.1.17713.5.16.4.1not-accessiblecurrent
sNMPTrapTableIndex
OBJECT-TYPE
SNMP trap value, used to index the SNMPTrapTable.
1.3.6.1.4.1.17713.5.16.4.1.1INTEGER (1..2)not-accessiblecurrent
sNMPTrapIPAddress
OBJECT-TYPE
The IP address to which all SNMP Traps are sent. An IP Address of 0.0.0.0 disables all TRAP generation. NB: A system reboot is required to activate changes to this attribute.
1.3.6.1.4.1.17713.5.16.4.1.2IpAddressread-writecurrent
sNMPTrapPortNumber
OBJECT-TYPE
Destination port for SNMP Traps (default=162). A value of 0 will disable the trap receiver. NB: A system reboot is required to activate changes to this attribute.
1.3.6.1.4.1.17713.5.16.4.1.3INTEGER (0..65535)read-writecurrent
sNMPTrapVersion
OBJECT-TYPE
The SNMP protocol version to use for SNMP Traps. NB: A system reboot is required to activate changes to this attribute
1.3.6.1.4.1.17713.5.16.5INTEGER {v1(0), v2c(1)}read-writecurrent
sNMPEnabledTraps
OBJECT-TYPE
This controls which SNMP Traps the unit will send
1.3.6.1.4.1.17713.5.16.6Bits {unknown8(0), dataPortUpDown(1), authenticationFailure(2), enabledDiagnosticAlarms(3), dFSImpulseInterference(4), channelChange(5), wirelessLinkUpDown(6), coldStart(7), telecomsChannelUpDown(15)}read-writecurrent
enabledDiagnosticAlarms
OBJECT-TYPE
Controls which individual diagnostic alarms are enabled. The unit may be configured to generate SNMP traps and/or SMTP email alerts for these enabled alarms by selecting 'Enabled Diagnostic Alarms' on the 'SNMP Enabled Traps' and/or 'SMTP Enabled Messages' attributes
1.3.6.1.4.1.17713.5.16.7Bits {incompatibleMasterAndSlave(0), incompatibleRegionCodes(1), unknown6(2), unknown5(3), unitOutOfCalibration(4), installArmState(5), installStatus(6), regionCode(7), telecomsChannelStatus(8), unknown15(9), dataPortStatus(10), dataPortDisabledWarning(11), wirelessLinkDisabledWarning(12), sNTPSynchronizationFailed(13), noWirelessChannelAvailable(14), dataPortConfigurationMismatch(15), syslogClientDisabledWarning(16), licensedCapacityMismatch(17), syslogLocalWrapped(18), syslogLocalNearlyFull(19), syslogLocalEnableDisable(20), linkModeOptimizationMismatch(21), tDDSynchronizationAlarm(22), telecomsChannelLoopback(23)}read-writecurrent
sNMPSendAllTrapsAtStartup
OBJECT-TYPE
Controls whether cleared traps are reported at start-up as well as raised traps. Only enabled traps will be reported. NB: Traps corresponding to transient events (i.e. not associated with an alarm or status value) are only sent when required and not at start-up.
1.3.6.1.4.1.17713.5.16.8INTEGER {disabled(0), enabled(1)}read-writecurrent
sntp
OBJECT-IDENTITY
1.3.6.1.4.1.17713.5.17
sNTPState
OBJECT-TYPE
SNTP control state
1.3.6.1.4.1.17713.5.17.1INTEGER {disabled(0), enabled(1)}read-writecurrent
sNTPServerIPAddress
OBJECT-TYPE
The IP address of a valid SNTP server
1.3.6.1.4.1.17713.5.17.2IpAddressread-writecurrent
sNTPServerPortNumber
OBJECT-TYPE
The IP port number of the SNTP server. Defaults to port 123.
1.3.6.1.4.1.17713.5.17.3INTEGER (0..65535)read-writecurrent
sNTPPollInterval
OBJECT-TYPE
The SNTP server polling interval
1.3.6.1.4.1.17713.5.17.4INTEGER (60..43200)read-writecurrent
sNTPSync
OBJECT-TYPE
If SNTP Sync fails then check the server settings in the Remote Management page, or disable SNTP. NB: a change of state may generate an SNMP trap and/or SMTP email alert
1.3.6.1.4.1.17713.5.17.5INTEGER {noSync(0), inSync(1)}read-onlycurrent
sNTPLastSync
OBJECT-TYPE
Last SNTP sync time
1.3.6.1.4.1.17713.5.17.6Integer32read-onlycurrent
systemClock
OBJECT-TYPE
System clock presented as local time
1.3.6.1.4.1.17713.5.17.7Integer32read-onlycurrent
timeZone
OBJECT-TYPE
Time zone offsets from Greenwich Mean Time (GMT)
1.3.6.1.4.1.17713.5.17.8INTEGER {gmtMinus1200(0), gmtMinus1130(1), gmtMinus1100(2), gmtMinus1030(3), gmtMinus1000(4), gmtMinus0930(5), gmtMinus0900(6), gmtMinus0830(7), gmtMinus0800(8), gmtMinus0730(9), gmtMinus0700(10), gmtMinus0630(11), gmtMinus0600(12), gmtMinus0530(13), gmtMinus0500(14), gmtMinus0430(15), gmtMinus0400(16), gmtMinus0330(17), gmtMinus0300(18), gmtMinus0230(19), gmtMinus0200(20), gmtMinus0130(21), gmtMinus0100(22), gmtMinus0030(23), gmtZero(24), gmtPlus0030(25), gmtPlus0100(26), gmtPlus0130(27), gmtPlus0200(28), gmtPlus0230(29), gmtPlus0300(30), gmtPlus0330(31), gmtPlus0400(32), gmtPlus0430(33), gmtPlus0500(34), gmtPlus0530(35), gmtPlus0600(36), gmtPlus0630(37), gmtPlus0700(38), gmtPlus0730(39), gmtPlus0800(40), gmtPlus0830(41), gmtPlus0900(42), gmtPlus0930(43), gmtPlus1000(44), gmtPlus1030(45), gmtPlus1100(46), gmtPlus1130(47), gmtPlus1200(48), gmtPlus1230(49), gmtPlus1300(50)}read-writecurrent
daylightSaving
OBJECT-TYPE
Daylight Saving Time
1.3.6.1.4.1.17713.5.17.9INTEGER {disabled(0), enabled(1)}read-writecurrent
reset
OBJECT-IDENTITY
1.3.6.1.4.1.17713.5.18
systemReset
OBJECT-TYPE
Setting this attribute to '1' will cause a system reboot. NB: a system reboot will apply any pending new settings held in memory
1.3.6.1.4.1.17713.5.18.1INTEGER {running(0), consoleReboot(1)}read-writecurrent
versions
OBJECT-IDENTITY
1.3.6.1.4.1.17713.5.19
softwareVersion
OBJECT-TYPE
Current software version
1.3.6.1.4.1.17713.5.19.1DisplayString (SIZE(0..63))read-onlycurrent
hardwareVersion
OBJECT-TYPE
Hardware platform version
1.3.6.1.4.1.17713.5.19.2DisplayString (SIZE(0..63))read-onlycurrent
secondarySoftwareVersion
OBJECT-TYPE
Secondary software version, used when the primary software image is invalid or erased
1.3.6.1.4.1.17713.5.19.3DisplayString (SIZE(0..63))read-onlycurrent
bootVersion
OBJECT-TYPE
Boot code software version
1.3.6.1.4.1.17713.5.19.4DisplayString (SIZE(0..63))read-onlycurrent
pubStats
OBJECT-IDENTITY
1.3.6.1.4.1.17713.5.20
receiveDataRate
OBJECT-TYPE
Average data rate over the last one second interval (kbps)
1.3.6.1.4.1.17713.5.20.1Integer32read-onlycurrent
transmitDataRate
OBJECT-TYPE
Average data rate over the last one second interval (kbps)
1.3.6.1.4.1.17713.5.20.2Integer32read-onlycurrent
aggregateDataRate
OBJECT-TYPE
Average data rate over the last one second interval (kbps)
1.3.6.1.4.1.17713.5.20.3Integer32read-onlycurrent
wirelessLinkAvailability
OBJECT-TYPE
Link availability calculated since the last reset of the system counters, as a percentage multiplied by 10000 to give four decimal places of precision
1.3.6.1.4.1.17713.5.20.4INTEGER (0..1000000)read-onlycurrent
wirelessLinkStatus
OBJECT-TYPE
Current status of the wireless link
1.3.6.1.4.1.17713.5.20.5INTEGER {up(0), registering(1), acquiring(2), searching(3), radarCAC(4), initialising(5)}read-onlycurrent
byteErrorRatio
OBJECT-TYPE
Reciprocal of the byte error ratio calculated since the last reset of the system counters
1.3.6.1.4.1.17713.5.20.6Integer32read-onlycurrent
receiveModulationModeDetail
OBJECT-TYPE
The reason for the current receive modulation mode
1.3.6.1.4.1.17713.5.20.7INTEGER {runningAtMaximumReceiveMode(0), runningAtUserConfiguredMaxModulationMode(1), restrictedBecauseInstallationIsArmed(2), restrictedBecauseOfByteErrorsOnTheWirelessLink(3), restrictedBecauseTheLinkParametersAreUpdating(4), restrictedBecauseChannelChangeIsInProgress(5), restrictedDueToTheLowEthernetLinkSpeed(6), runningAtMaximumReceiveModeForChannelBandwidth(7), limitedByTheWirelessConditions(8)}read-onlycurrent
encryption
OBJECT-IDENTITY
1.3.6.1.4.1.17713.5.22
encryptionAlgorithm
OBJECT-TYPE
The Encryption Algorithm used by the wireless link. NB: A system reboot is required to activate changes to this attribute. NB: The same Encryption Algorithm must be configured at BOTH ends of the link for it to function correctly
1.3.6.1.4.1.17713.5.22.1INTEGER {none(0), aESRijndael(1), aES256bitRijndael(2)}read-onlycurrent
tDDControl
OBJECT-IDENTITY
1.3.6.1.4.1.17713.5.23
tDDSynchronizationMode
OBJECT-TYPE
TDD Synchronization Mode selection
1.3.6.1.4.1.17713.5.23.1INTEGER {disabled(0), enabled(1)}read-onlycurrent
syslogControl
OBJECT-IDENTITY
1.3.6.1.4.1.17713.5.24
syslogClient
OBJECT-TYPE
Enable or disable the syslog client
1.3.6.1.4.1.17713.5.24.1INTEGER {disabled(0), enabled(1)}read-onlycurrent
syslogState
OBJECT-TYPE
The syslog service has been enabled or disabled
1.3.6.1.4.1.17713.5.24.2INTEGER {disabled(0), enabled(1)}read-onlycurrent
aAAControl
OBJECT-IDENTITY
1.3.6.1.4.1.17713.5.25
userTableNumber
OBJECT-TYPE
Number of entries in the userTable
1.3.6.1.4.1.17713.5.25.1INTEGER (1..10)read-onlycurrent
userTable
OBJECT-TYPE
The User Table Control group contains objects specifically for user account management.
1.3.6.1.4.1.17713.5.25.2not-accessiblecurrent
userTableEntry
OBJECT-TYPE
Table UserTable
1.3.6.1.4.1.17713.5.25.2.1not-accessiblecurrent
userTableIndex
OBJECT-TYPE
used to index values in the userTable.
1.3.6.1.4.1.17713.5.25.2.1.1INTEGER (1..10)not-accessiblecurrent
userName
OBJECT-TYPE
User name which must be entered, along with the appropriate password, in order to gain access to the system.
1.3.6.1.4.1.17713.5.25.2.1.2OCTET STRINGread-onlycurrent
userRole
OBJECT-TYPE
Role of the selected user. A Security Officer has access to and can modify all settings. A System Administrator has access to and can modify all non-security settings. A Read Only user can view settings, but cannot make any changes.
1.3.6.1.4.1.17713.5.25.2.1.3INTEGER {readOnly(0), systemAdministrator(1), securityOfficer(2)}read-onlycurrent
userEnabled
OBJECT-TYPE
Enable / Disable the selected user
1.3.6.1.4.1.17713.5.25.2.1.4INTEGER {disabled(0), enabled(1)}read-onlycurrent
userPassword
OBJECT-TYPE
User password, which must be entered in order to gain access to the system.
1.3.6.1.4.1.17713.5.25.2.1.5OCTET STRINGread-writecurrent
supplementary
OBJECT-IDENTITY
1.3.6.1.4.1.17713.5.96
longitude
OBJECT-TYPE
The longitude of the unit, measured in decimal degrees. This object is set by the SNMP manager and has no internal function.
1.3.6.1.4.1.17713.5.96.1DisplayString (SIZE(0..19))read-writecurrent
latitude
OBJECT-TYPE
The latitude of the unit, measured in decimal degrees. This object is set by the SNMP manager and has no internal function.
1.3.6.1.4.1.17713.5.96.2DisplayString (SIZE(0..19))read-writecurrent
altitude
OBJECT-TYPE
The altitude of the unit, measured in metres. This object is set by the SNMP manager and has no internal function.
1.3.6.1.4.1.17713.5.96.3Integer32read-writecurrent
ptpGroups
OBJECT-IDENTITY
1.3.6.1.4.1.17713.5.98
ptpTraps
OBJECT-IDENTITY
1.3.6.1.4.1.17713.5.99
ptpTrapPrefix
OBJECT-IDENTITY
1.3.6.1.4.1.17713.5.99.0

Notifications

NameOIDStatus
channelChangeTrap
NOTIFICATION-TYPE
The PTP radio has changed wireless channel. This has been caused by either i) mandatory radar avoidance, a DFS impulsive interference event will also be detected, or ii) Dynamic Spectrum Optimization, (DSO) DSO improves link performance by selecting the most appropriate transmit and receive channels with the lowest level of interference.
1.3.6.1.4.1.17713.5.99.0.1current
dfsImpulsiveInterferenceTrap
NOTIFICATION-TYPE
DFS impulsive interference detected event
1.3.6.1.4.1.17713.5.99.0.2current
dataPortStatusTrap
NOTIFICATION-TYPE
Current status of the Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert
1.3.6.1.4.1.17713.5.99.0.3current
telecomsChannelStatusTrap
NOTIFICATION-TYPE
Current status of telecoms channel. NB: a change of state may generate an SNMP trap and/or SMTP email alert
1.3.6.1.4.1.17713.5.99.0.4current
telecomsLoopbackTrap
NOTIFICATION-TYPE
The loopback status of telecoms channel. This is intended for installation testing and should be set to 'None' for normal operation. The wire connections to a unit can be tested by applying a 'Copper' loopback to the local unit. The wireless connection to the remote unit can be tested by applying a 'Wireless' loopback to the remote unit with no loopback on the local unit. When applying a wireless loopback, please ensure that the other end of the link has a loopback setting of 'None'. NB: a change of state may generate an SNMP trap and/or SMTP email alert
1.3.6.1.4.1.17713.5.99.0.6current
regionCodeTrap
NOTIFICATION-TYPE
The region code prohibits the wireless unit from operating outside the regulated limits. An invalid region code indicates a corrupted licence key. NB: a change of state may generate an SNMP trap and/or SMTP email alert
1.3.6.1.4.1.17713.5.99.0.8current
installStatusTrap
NOTIFICATION-TYPE
A non-zero value indicates that signalling was received with the wrong MAC address or a mismatched link name. NB: It is very unusual to detect this, because units with mis-configured Target MAC Address will normally fail to establish a wireless link. However, rare circumstances may establish a partial wireless link and detect this situation. NB: A non-zero value on start-up, or a change of value during operation, may generate an SNMP trap and/or SMTP email alert
1.3.6.1.4.1.17713.5.99.0.9current
installArmStateTrap
NOTIFICATION-TYPE
Indicates if the unit is being installed. NB: a value other than 'disarmed' on startup, or a change of state during operation may generate an SNMP trap and/or SMTP email alert
1.3.6.1.4.1.17713.5.99.0.10current
unitOutOfCalibrationTrap
NOTIFICATION-TYPE
The unit is out of calibration
1.3.6.1.4.1.17713.5.99.0.11current
incompatibleRegionCodesTrap
NOTIFICATION-TYPE
The master and slave units have incompatible region codes. NB: Both units must have compatible licence keys
1.3.6.1.4.1.17713.5.99.0.14current
noWirelessChannelAvailableTrap
NOTIFICATION-TYPE
Spectrum Management was unable to locate a suitable wireless channel to operate on
1.3.6.1.4.1.17713.5.99.0.15current
wirelessLinkDisabledWarningTrap
NOTIFICATION-TYPE
The SNMP ifAdminStatus of the wireless interface has disabled wireless traffic
1.3.6.1.4.1.17713.5.99.0.16current
dataPortDisabledWarningTrap
NOTIFICATION-TYPE
The SNMP ifAdminStatus of the Ethernet interface has disabled Ethernet traffic
1.3.6.1.4.1.17713.5.99.0.17current
dataPortConfigurationMismatchTrap
NOTIFICATION-TYPE
The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch
1.3.6.1.4.1.17713.5.99.0.19current
incompatibleMasterAndSlaveTrap
NOTIFICATION-TYPE
A non-zero value indicates that the master and slave ends of a link are different hardware products, or have different software versions. NB: It is very unusual to detect this, because incompatible units will normally fail to establish a wireless link. However, some combinations may establish a partial wireless link and detect this situation. NB: A non-zero value may generate an SNMP trap and/or SMTP email alert
1.3.6.1.4.1.17713.5.99.0.20current
sNTPSyncTrap
NOTIFICATION-TYPE
If SNTP Sync fails then check the server settings in the Remote Management page, or disable SNTP. NB: a change of state may generate an SNMP trap and/or SMTP email alert
1.3.6.1.4.1.17713.5.99.0.21current
tDDSynchronizationAlarmTrap
NOTIFICATION-TYPE
Not Synchronized indicates failure of the external timing system for a period greater than the holdover timer. TDD frame timing will have drifted, and this link may cause interference with other links in a synchronized network. Timing System Failure is an early warning, indicating that 80% of the holdover period has expired.
1.3.6.1.4.1.17713.5.99.0.22current
linkModeOptimizationMismatchTrap
NOTIFICATION-TYPE
The remote node of this link has been configured with a different link mode optimization
1.3.6.1.4.1.17713.5.99.0.25current
capacityLicenseMismatchTrap
NOTIFICATION-TYPE
The local and remote units have different licensed capacity and/or the full capacity trial has been activated at only one unit. The wireless link is operating at the capacity of the lowest capacity unit
1.3.6.1.4.1.17713.5.99.0.27current
syslogStateTrap
NOTIFICATION-TYPE
The syslog service has been enabled or disabled
1.3.6.1.4.1.17713.5.99.0.30current
syslogLocalNearlyFullTrap
NOTIFICATION-TYPE
The syslog local log is nearly full (90%)
1.3.6.1.4.1.17713.5.99.0.31current
syslogLocalWrappedTrap
NOTIFICATION-TYPE
The syslog local log has wrapped
1.3.6.1.4.1.17713.5.99.0.32current
syslogClientTrap
NOTIFICATION-TYPE
Enable or disable the syslog client
1.3.6.1.4.1.17713.5.99.0.33current

Conformance

NameOIDStatus
ptpCompliance
MODULE-COMPLIANCE
The compliance statement for the Cambium PTP MIB
1.3.6.1.4.1.17713.5.97current
dfsGroup
OBJECT-GROUP
The dfs object group.
1.3.6.1.4.1.17713.5.98.3current
configurationGroup
OBJECT-GROUP
The configuration object group.
1.3.6.1.4.1.17713.5.98.5current
ethernetGroup
OBJECT-GROUP
The ethernet object group.
1.3.6.1.4.1.17713.5.98.6current
telecomGroup
OBJECT-GROUP
The telecom object group.
1.3.6.1.4.1.17713.5.98.7current
licenceGroup
OBJECT-GROUP
The licence object group.
1.3.6.1.4.1.17713.5.98.8current
managementGroup
OBJECT-GROUP
The management object group.
1.3.6.1.4.1.17713.5.98.9current
phyControlGroup
OBJECT-GROUP
The phyControl object group.
1.3.6.1.4.1.17713.5.98.10current
phyStatusGroup
OBJECT-GROUP
The phyStatus object group.
1.3.6.1.4.1.17713.5.98.12current
alarmsGroup
OBJECT-GROUP
The alarms object group.
1.3.6.1.4.1.17713.5.98.13current
smtpGroup
OBJECT-GROUP
The smtp object group.
1.3.6.1.4.1.17713.5.98.15current
snmpControlGroup
OBJECT-GROUP
The snmpControl object group.
1.3.6.1.4.1.17713.5.98.16current
sntpGroup
OBJECT-GROUP
The sntp object group.
1.3.6.1.4.1.17713.5.98.17current
resetGroup
OBJECT-GROUP
The reset object group.
1.3.6.1.4.1.17713.5.98.18current
versionsGroup
OBJECT-GROUP
The versions object group.
1.3.6.1.4.1.17713.5.98.19current
pubStatsGroup
OBJECT-GROUP
The pubStats object group.
1.3.6.1.4.1.17713.5.98.20current
encryptionGroup
OBJECT-GROUP
The encryption object group.
1.3.6.1.4.1.17713.5.98.22current
tDDControlGroup
OBJECT-GROUP
The tDDControl object group.
1.3.6.1.4.1.17713.5.98.23current
syslogControlGroup
OBJECT-GROUP
The syslogControl object group.
1.3.6.1.4.1.17713.5.98.24current
aAAControlGroup
OBJECT-GROUP
The aAAControl object group.
1.3.6.1.4.1.17713.5.98.25current
supplementaryGroup
OBJECT-GROUP
The supplementary object group.
1.3.6.1.4.1.17713.5.98.96current
notificationsGroup
NOTIFICATION-GROUP
The notifications group.
1.3.6.1.4.1.17713.5.98.99current