BTI-7000-MIB

TEXTUAL-CONVENTION

The DataCommsPingCmd textual convention is the value of the dataCommsPingCmd object which is used to perform a ping operation over the NE's OSC. The operation is initiated when a set request is performed on the dataCommsPingCmd object with a value corresponding to the ping action, as explained below. The valid values for DataCommsPingCmd that can be used in a set operation are: - 'ping', used to trigger the ping operation over the OSC A value of 'pingInProgress' is returned when the dataCommsPingCmd object is read in a get operation if the ping command entered has not yet completed, otherwise 'noOp' is returned. In order for the set request on a DataCommsPingCmd object to complete successfully, the dataCommsPingCmd object, along with the dataCommdPingAddress and optionally the dataCommsPingNumAttemps objects must be set in the same set request for a given row of the table. The purpose of these objects is: - dataCommsPingAddress: indicates the IP Address which is the target of the ping operation - dataCommsPingNumAttempts: indicates how many ping attempts are to be made in the ping operation Once the dataCommsPingCmd operation is completed by way of the set operation on the dataCommsPingCmd and associated objects, the result of the operation is checked by performing a get operation on the dataCommsPingNumSuccesses object. When the ping operation completes, the value of this object will be set to the number of the attempted ping trials that resulted in a successful ping.

TEXTUAL-CONVENTION

The MSCP maintains all provisionable data in non-volatile storage so that configuration settings are retained during system shutdowns and restarts. The configuration database is version controlled to facilitate the detection of an incompatible software load and/or database. The BTI 7000 Series supports user-initiated backup and restore operations of the configuration database through the SNMP Set requests performed on the dbBackupAndRestoreCmd object with a value corresponding to the required action. In a backup operation, the database is uploaded to a user-specified network location (that is, a local PC or a remote PC) using the file transfer protocol (FTP), or it is stored locally on the MSCP. In a restore operation, the database is restored using a version of the file from an FTP server or locally from the MSCP. The integrity of the file is validated to ensure that it matches the current software load on the BTI 7000 Series. The DbBackupAndRestoreCmd textual convention is the value of the dbBackupAndRestoreCmd object, which is used to activate a database backup operation, or the various steps of a database restore operation. These operations are initiated when a set request is performed on the dbBackupAndRestoreCmd object with a value corresponding to the desired action, as explained below. A get request on this type returns the value noOp. The valid values for DbBackupAndRestoreCmd that can be used in a set operation are: - 'invokeBackup': used to perform a database backup operation. The operation may be used to perform a local database backup, or to save the database backup to a remote repository. - 'loadRestore': used to initiate a database restore operation. The operation may be the restoration of a local database backup or of a remote database backup - 'invokeRestore': continues a database restore operation after the loadRestore stage has completed. The database being restored is made active on the SCP circuit pack at this stage. - 'applyRestore': Obsolete this functionality is now done as part of the invokeRestore. - 'commitRestore': is used to complete a database restore operation and can be used after the applyRestore action completes - 'cancelRestore': is used to cancel and back out of a database restore operation in progress and can be used before the commitRestore action is called. In order for the set request on the dbBackupAndRestoreCmd object to complete successfully, the values of other objects must be set in the same set request for some of the commands. The additional objects required to be set along with the dbBackupAndRestoreCmd object for each DbBackupAndRestoreCmd value are listed below. - invokeBackup: must also set dbBackupAndRestoreType. If this object is set to remote, then the dbBackupAndRestoreAddress, dbBackupAndRestoreFtpUser and dbBackupAndRestorePswd object values must also be specified in the set request. The dbBackupAndRestoreCheckAlm object may optionally be set when the invokeBackup action is performed. Also when the dbBackupAndRestoreType is set to remote the dbBackupAndRestorePath is optional. If not specified the default name is used. - loadRestore: must also set dbBackupAndRestoreType. If this object is set to remote, then the dbBackupAndRestoreAddress, dbBackupAndRestorePath, dbBackupAndRestoreFtpUser and dbBackupAndRestorePswd object values must also be specified in the set request. The dbBackupAndRestoreCheckSysName object may be set when the loadRestore action is performed, but is not mandatory. - invokeRestore: must also set dbBackupAndRestoreInvokeFilename to confirm the name of the backed file to be used in the restore operation. Optionally, the dbBackupAndRestoreCheckAlm object may be set. - applyRestore, commitRestore, cancelRestore: no additional object values are required to be included for these set requests

TEXTUAL-CONVENTION

Indicates the type of database backup operation to be performed, or the type of database restore operation to be performed. The meaning of the values are as follows. - 'local': for a database backup, the backup is made on the NE itself; for a database restore, the restoration is from a local database backup file - 'remote': for a database backup, the backup is made to an external ftp server; for a database restore, the restoration is from a database file located on an external ftp server - 'remoteSftp': for a database backup, the backup is made to an external sftp server; for a database restore, the restoration is from a database file located on an external sftp server

TEXTUAL-CONVENTION

All BTI 7000 Series circuit packs are shipped with pre-loaded software. At system commissioning, it is not necessary to start the system by loading software. However, during the life cycle of the BTI 7000 Series, it might be necessary to upgrade the system software. Normally, the system software is upgraded to: � Support the functionality of new circuit packs � Provide new features for existing circuit packs � Add specific software improvements Performing a system software upgrade on the BTI 7000 Series is non-service affecting. The upgrade process is designed for application environments that require that the optical signals passing through the BTI 7000 Series are not interrupted. The BTI 7000 Series supports a user-initiated software upgrade operation through the SNMP Set requests performed on the swUpgradeCmd object with a value corresponding to the required action. The SwUpgradeCmd textual convention is the value of the swUpgradeCmd object, which is used to activate the various steps of the software upgrade procedure on the system. These steps are initiated when a set request is performed on the swUpgradeCmd object with a value corresponding to the desired action, as explained below. A get request will return the value noOp. The valid values for SwUpgradeCmd that can be used in a set operation are: - 'checkUpgrade': used to perform a pre-upgrade check of the system to ensure that it is ready for the upgrade process, and that the load files on the server are accessible. - 'loadUpgrade': used to initiate a system upgrade by downloading the load files from a remote server to the SCP software load storage area. - 'invokeUpgrade': continues a system upgrade operation after the loadUpgrade stage has completed. First the upgrade load is installed on all circuit packs in the system, then each card is rebooted to run the upgrade load. - 'commitUpgrade': is used to complete a system upgrade operation and can be used after the invkUpgrade action completes - 'cancelUpgrade': is used to cancel and back out of a system software upgrade operation in progress and can be used before the cmmtUpgrade action is called. - 'invokeScpUpgrade': is a special-purpose upgrade step used in place of the invkUpgrade value when an upgrade is being performed on an SCP pack only. Such a targeted upgrade is valid only when an SCP pack is replaced and the new pack requires a software upgrade to make its software version consistent with the system In order for the set request on the swUpgradeCmd object to complete successfully, the values of other objects must be set in the same set request for some of the commands. The additional objects required to be set along with the swUpgradeCmd object for each SwUpgradeCmd value are listed below. - checkUpgrade, loadUpgrade: must also set swUpgradeAddress, swUpgradePath, swUpgradeFtpUser, swUpgradeFtpPswd and swUpgradeFileTransferType object values to indicate where the ftp or sftp server with the upgrade load files is to be found, along with access parameters. - invokeUpgrade, invokeScpUpgrade: must also set the swUpgradeInvokeRelNum object to confirm the software version that is to be used in the upgrade. The swUpgradeCheckAlm object may be set, but is not mandatory. - commitUpgrade, cancelUpgrade: no additional object values are required to be specified for these set requests.

TEXTUAL-CONVENTION

Indicates the protocol of the file transfer. - 'ftp': an external ftp server is the source for the load to be transfered. - 'sftp': an external sftp server is the source for the load to be transfered.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

The software version that is active on the NE currently.

OBJECT-TYPE

This is a unique network element number used to identify the network element and to differentiate it from other NEs in the management domain.

OBJECT-TYPE

This is a network element site number used to uniquely identify the site of the NE and to differentiate it from other NE sites in the management domain.

OBJECT-TYPE

The current system date and time, without time zone information.

OBJECT-TYPE

The time zone in which the local time of this system is to be reported. Typically, the time zone is the one in which the system is physically located.

OBJECT-TYPE

A setting that indicates whether the system time should be updated automatically in accordance with the daylight savings time characteristics of the current time zone.

OBJECT-TYPE

The default IP routing gateway for network management interfaces on the node. If not specified, this object returns a value of 0.0.0.0.

OBJECT-TYPE

The secondary IP routing gateway for network management interfaces on the node. If not specified, this object returns a value of 0.0.0.0.

OBJECT-TYPE

The IP routing gateway that is currently active on the node. If no gateway is active, this object returns a value of 0.0.0.0.

OBJECT-TYPE

A setting that specifies if automatic provisioning of equipment and facilities is enabled. If automatic provisioning is enabled, this object indicates the default administration status. The possible values include: - enabled: Applicable entities are auto provisioned with the initial state enabled. - disabled: Applicable entities are auto provisioned with the initial state disabled. - autoEnabled: Applicable entities are auto provisioned and placed into the auto-enabled state. - autoProvOff: Auto provisioning is disabled.

OBJECT-TYPE

The time delay after a physical shelf or circuit pack is removed from the NE before the provisioned entities that are supported by the removed equipment are automatically deprovisioned. If this object is set to a value of 000-00, auto deprovisioning is disabled.

OBJECT-TYPE

The system wide default auto-enable timer value. This timer specifies a time delay after a provisioned facility in the auto-enabled state is cleared of all alarms before the state of the facility transitions to enabled. The default value can be overridden by a facility-specific value that is specified when the facility is either provisioned or edited in its respective table.

OBJECT-IDENTITY

OBJECT-TYPE

The polling rate for the NTP client to periodically fetch the system time from the list of NTP servers configured.

OBJECT-TYPE

The NTP authentication key ID, if authentication is required.

OBJECT-TYPE

Status indicating if the node is in sync with one of the time servers. Either Y or N.

OBJECT-TYPE

Specifies the stratum of the timer server the node in in sync with.

OBJECT-TYPE

The IP address of the time server the node is in sync with.

OBJECT-TYPE

A list of NTP servers to poll for the system time. The NTP client then decides which is best clock source.

OBJECT-TYPE

The list entry for an NTP server.

OBJECT-TYPE

The IP address of the NTP server.

OBJECT-TYPE

Used to control the addition and deletion of entries in the NTP client association table.

OBJECT-TYPE

The date and time of the system before the NTP client updated the system clock.

OBJECT-TYPE

The new system date and time updated by the NTP client.

OBJECT-TYPE

This the NTP server being used as the clock reference for the system.

OBJECT-TYPE

This is the stratum of the NTP server being used as the clock reference for the system.

OBJECT-TYPE

A setting that indicates whether the system should report pack missing alarms.

OBJECT-TYPE

A system wide setting that specifies whether the circuit pack pack high temperature automatic shutdown (HTAS) is enabled. When enabled, the circuit packs which support the HTAS feature will be automatically powered down if the shutdown temperature threshold for that circuit pack is exceeded. There will be alarms indicating that the shutdown has occurred. The default setting is enabled.

OBJECT-IDENTITY

OBJECT-TYPE

This table contains one row for every physically detected shelf on the NE. Each row contains a list of attributes that pertain to a physical shelf.

OBJECT-TYPE

The conceptual row object of the shelf inventory table.

OBJECT-TYPE

The number of the shelf. It is set to 1 for the main shelf, otherwise the object is based on the expansion shelf port on which the shelf is detected, and the number of hops from the main shelf.

OBJECT-TYPE

The NE name expected by the main shelf to be reported by the expansion shelf as the name of the NE to which it belongs.

OBJECT-TYPE

The string representation of the NE NMS IP address that is expected by the main shelf to be reported by the expansion shelf as the IP address of the NE to which it belongs.

OBJECT-TYPE

The number of the expansion shelf that is expected by the main shelf to be reported by the attached shelf.

OBJECT-TYPE

The serial number of the Main Shelf Interface circuit pack that is expected by the main shelf to be reported by the expansion shelf as the MSI serial number of the NE main shelf to which it belongs.

OBJECT-TYPE

The actual NE name reported by the expansion shelf as the name of the NE to which it belongs.

OBJECT-TYPE

The string representation of the actual NE NMS IP address reported by the expansion shelf as the IP address of the NE to which it belongs.

OBJECT-TYPE

The actual number of the expansion shelf reported by the attached shelf.

OBJECT-TYPE

The actual serial number of the Main Shelf Interface circuit pack reported by the expansion shelf as the MSI serial number of the NE main shelf to which it belongs.

OBJECT-TYPE

Indicates if the shelf functions as a main shelf or an expansion shelf.

OBJECT-TYPE

A concise representation of the shelf brand name.

OBJECT-TYPE

The full representation of the shelf brand name.

OBJECT-TYPE

A string representation of the Product Equipment Code for the shelf chassis alone.

OBJECT-TYPE

A string representation of the Telcordia Common Language Equipment Identifier for the shelf chassis alone.

OBJECT-TYPE

A string representation of the Product Equipment Code for the shelf assembly, which bundles the shelf chassis, shelf interface pack, and cooling unit.

OBJECT-TYPE

The shelf hardware revision number. A value of 0 indicates that the revision is unspecified.

OBJECT-TYPE

The shelf configuration with respect to the number of slots for holding replaceable circuit packs. Note: This object is no longer supported as of BTI 7000 Release 8.1.0, and is maintained in the MIB for backwards- compatibility for management of pre-8.1 nodes.

OBJECT-TYPE

The Unique Serial Identifier (only for FNC-branded equipment)

OBJECT-TYPE

The serial number of the unit.

OBJECT-TYPE

The shelf manufacture date in the format YYYY-MM-DD.

OBJECT-TYPE

The shelf manufacture location.

OBJECT-TYPE

The shelf test date in the format YYYY-MM-DD.

OBJECT-TYPE

The shelf test location.

OBJECT-TYPE

This table contains one row for every slot on every shelf of the NE in which a circuit pack or other replaceable unit is seated. Each row contains a list of attributes that pertain to the circuit pack within the slot.

OBJECT-TYPE

The conceptual row object of the slot inventory table.

OBJECT-TYPE

The number of the shelf on which the slot inventory item is detected.

OBJECT-TYPE

The type of slot that contains the inventory item.

OBJECT-TYPE

The number of the slot within the shelf containing the inventory item. The number is from 1 to 20 for regular circuit pack slots. For main shelf interface type slots, the number is set to 0. For 7060/7030/7020 expansion shelf interface and cooling unit type slots, the number is set to 0. For 7200 common communications module type slots, the number is 1 or 2. For 7200 cooling unit type slots, the number is from 1 to 4.

OBJECT-TYPE

The version of the software running on the circuit pack in the given slot.

OBJECT-TYPE

A concise representation of the name of the circuit pack or unit.

OBJECT-TYPE

The full name of the circuit pack or unit.

OBJECT-TYPE

The Product Equipment Code for the circuit pack or unit.

OBJECT-TYPE

The Telcordia Common Language Equipment Identifier for the circuit pack or unit.

OBJECT-TYPE

The serial number of the unit.

OBJECT-TYPE

The circuit pack or unit hardware revision number. A value of 0 indicates that the revision is unspecified.

OBJECT-TYPE

The circuit pack manufacture date in the format YYYY-MM-DD.

OBJECT-TYPE

The circuit pack manufacture location.

OBJECT-TYPE

The circuit pack test date in the format YYYY-MM-DD.

OBJECT-TYPE

The circuit pack test location.

OBJECT-TYPE

The stage of the circuit pack upgrade process that has been completed.

OBJECT-TYPE

Indicates if the identified stage of the circuit pack upgrade process has resulted in success or failure.

OBJECT-TYPE

The Unique Serial Identifier (only for FNC-branded equipment)

OBJECT-TYPE

The circuit pack high temperature threshold.

OBJECT-TYPE

The circuit pack shutdown temperature threshold.

OBJECT-TYPE

This table contains one row for every SFP/XFP or other pluggable present on any circuit pack or other replaceable unit present in the NE. Each row contains a list of attributes that pertain to the detected SFP/XFP.

OBJECT-TYPE

The conceptual row object of the pluggable inventory table.

OBJECT-TYPE

The number of the shelf on which the pluggable inventory item resides.

OBJECT-TYPE

The type of slot containing the pluggable inventory item.

OBJECT-TYPE

The number of the slot that contains the pluggable inventory item.

OBJECT-TYPE

The number of the port on the circuit pack that contains the pluggable inventory item.

OBJECT-TYPE

The type of small form-factor pluggable inventory item.

OBJECT-TYPE

The Product Equipment Code for the pluggable inventory item.

OBJECT-TYPE

The Telcordia Common Language Equipment Identifier for the pluggable inventory item.

OBJECT-TYPE

The Vendor Name of the pluggable inventory item.

OBJECT-TYPE

The Vendor IEEE Organizationally Unique Identifier.

OBJECT-TYPE

The Vendor Part Number.

OBJECT-TYPE

The Vendor Revision Number.

OBJECT-TYPE

The Vendor Serial Number.

OBJECT-TYPE

The manufacture date in the format YYYY-MM-DD..

OBJECT-TYPE

The type of connector on the pluggable unit.

OBJECT-TYPE

The minimum bit rate supported by the pluggable. A value of 0 means unspecified.

OBJECT-TYPE

The maximum bit rate supported by the pluggable. A value of 0 means unspecified.

OBJECT-TYPE

The nominal bit rate supported by the pluggable. A value of 0 means unspecified.

OBJECT-TYPE

A textual comma-delimited list of serial encoding mechanisms supported by the pluggable.

OBJECT-TYPE

The wavelength transmitted by the pluggable. A value of 0 means unspecified.

OBJECT-TYPE

The reach supported by the pluggable. A value of 0 means unspecified.

OBJECT-TYPE

Indicates if the pluggable implements the Transmit Fault signal.

OBJECT-TYPE

Indicates if the pluggable implements the Loss of Signal signal.

OBJECT-TYPE

Indicates if the pluggable implements support for Digital Diagnostics.

OBJECT-TYPE

Indicates if the pluggable implements support for disabling the transmit laser.

OBJECT-TYPE

The physical media type of the pluggable

OBJECT-TYPE

The Unique Serial Identifier (only for FNC-branded equipment)

OBJECT-TYPE

The wavelength minimum for the tunable pluggable. A value of 0 means unspecified.

OBJECT-TYPE

The wavelength maximum for the tunable pluggable.A value of 0 means unspecified.

OBJECT-TYPE

The wavelength spacing for the tunable pluggable. A value of 0 means unspecified.

OBJECT-TYPE

This table contains a listing of any specialized data records available for the slot inventory entries on the system. Each row contains a single item of data for a specialized data record for a slot inventory entry.

OBJECT-TYPE

The conceptual row object of the slot inventory data table.

OBJECT-TYPE

The number of the shelf on which the slot inventory item is detected.

OBJECT-TYPE

The type of slot that contains the inventory item.

OBJECT-TYPE

The number of the slot within the shelf containing the inventory item. The number is from 1 to 20 for regular circuit pack slots. For shelfInterface and coolingUnit type slots, the number is set to 0.

OBJECT-TYPE

The specialized data record index.

OBJECT-TYPE

The name of the data item.

OBJECT-TYPE

The value of the data item.

OBJECT-IDENTITY

OBJECT-TYPE

This table contains one row for every provisioned shelf on the NE. Each row contains a list of attributes that pertain to a provisioned shelf.

OBJECT-TYPE

The conceptual row object of the shelf table.

OBJECT-TYPE

The number of the shelf that has been provisioned. This is set to 1 for the main shelf. Otherwise, the number is based on the expansion shelf port number on which this shelf is expected to be detected and the number of hops from the main shelf.

OBJECT-TYPE

The provisioned configuration for the shelf. Note: This object is no longer supported as of BTI 7000 Release 8.1.0, and is maintained in the MIB for backwards- compatibility for management of pre-8.1 nodes.

OBJECT-TYPE

The configuration of the actual shelf discovered. Note: This object is no longer supported as of BTI 7000 Release 8.1.0, and is maintained in the MIB for backwards- compatibility for management of pre-8.1 nodes.

OBJECT-TYPE

Indicates if the provisioned shelf is a main or expansion shelf. Only expansion shelves can be created. The main shelf is automatically provisioned and can never be de-provisioned.

OBJECT-TYPE

Indicates the provisioned shelf Product Equipment Code. This is a mandatory object when a row of the shelf table is created. The PEC can only be set at the time of row creation, and it cannot be edited later.

OBJECT-TYPE

The administrative status of the shelf.

OBJECT-TYPE

The reported operational status of the shelf.

OBJECT-TYPE

A textual list of qualifiers of the reported operational status of the shelf.

OBJECT-TYPE

Textual data recorded by the user to describe the provisioned shelf in a manner useful to the user such as the location where the shelf is installed.

OBJECT-TYPE

A variable length text string for operating company use.

OBJECT-TYPE

A variable length text string for operating company use.

OBJECT-TYPE

A variable length text string for operating company use.

OBJECT-TYPE

The power feed mode for rail A.

OBJECT-TYPE

The power feed mode for rail B.

OBJECT-TYPE

Used to control the addition and deletion of entries in the shelf table, which in turn controls provisioning and deprovisioning of shelf objects.

OBJECT-TYPE

This table contains one row for every provisioned circuit pack on the NE. Each row contains a list of attributes that pertain to a provisioned circuit pack.

OBJECT-TYPE

The conceptual row object of the circuit pack table.

OBJECT-TYPE

The specific type of circuit pack provisioned.

OBJECT-TYPE

The number of the shelf on which the circuit pack is provisioned.

OBJECT-TYPE

The number of the slot in which the circuit pack is provisioned.

OBJECT-TYPE

Indicates the provisioned circuit pack Product Equipment Code. This is a mandatory object when a row of the circuit pack table is created. The PEC can only be set at the time of row creation, and it cannot be edited later.

OBJECT-TYPE

The administrative status of the circuit pack.

OBJECT-TYPE

The reported operational status of the circuit pack.

OBJECT-TYPE

A textual list of qualifiers of the reported operational status of the circuit pack.

OBJECT-TYPE

Textual data recorded by the user to describe the provisioned circuit pack in a manner useful to the user.

OBJECT-TYPE

A variable length text string for operating company use.

OBJECT-TYPE

A variable length text string for operating company use.

OBJECT-TYPE

A variable length text string for operating company use.

OBJECT-TYPE

Used in notifications sent during the circuit pack software upgrade process. It indicates the stage of the circuit pack upgrade process that has been completed.

OBJECT-TYPE

Indicates if the identified stage of the circuit pack upgrade process has resulted in success or failure.

OBJECT-TYPE

Used to control the addition and deletion of entries in the circuit pack table, which in turn controls the provisioning and de-provisioning of circuit pack objects.

OBJECT-IDENTITY

OBJECT-TYPE

This table contains one row for every provisioned optical amplifier facility on the NE. Each row contains a list of attributes that pertain to the optical amplifier.

OBJECT-TYPE

The conceptual row object of the optical amplifier table.

OBJECT-TYPE

The specific type of optical amplifier provisioned.

OBJECT-TYPE

The number of the shelf on which the optical amplifier facility is provisioned.

OBJECT-TYPE

The number of the slot in which the optical amplifier facility is provisioned.

OBJECT-TYPE

The number of the port on the circuit pack on which the optical amplifier facility is provisioned.

OBJECT-TYPE

The case temperature threshold.

OBJECT-TYPE

The case temperature shutdown threshold.

OBJECT-TYPE

The laser temperature minimum shutdown threshold. A default value is provided when the optical amplifier is created based on the optical amplifier type provisioned.

OBJECT-TYPE

The laser temperature maximum shutdown threshold. A default value is provided when the optical amplifier is created based on the optical amplifier type provisioned.

OBJECT-TYPE

The optical power received minimum threshold. A default value is provided when the optical amplifier is created based on the optical amplifier type provisioned.

OBJECT-TYPE

The optical power received maximum threshold. A default value is provided when the optical amplifier is created based on the optical amplifier type provisioned.

OBJECT-TYPE

The secondary stage input optical power received maximum threshold. This object is applicable only to OLAM type amplifiers.

OBJECT-TYPE

The optical power transmitted minimum threshold. A default value is provided when the optical amplifier is created based on the optical amplifier type provisioned.

OBJECT-TYPE

The optical power transmitted maximum threshold. A default value is provided when the optical amplifier is created based on the optical amplifier type provisioned.

OBJECT-TYPE

The optical back reflection safety threshold.

OBJECT-TYPE

This is the mid-stage maximum insertion loss signal threshold. It applies to mid-stage access amplifiers only.

OBJECT-TYPE

The optical amplifier case temperature.

OBJECT-TYPE

The temperature of the optical amplifier laser 1.

OBJECT-TYPE

The temperature of the optical amplifier laser 2.

OBJECT-TYPE

The optical power received on the input of the amplifier.

OBJECT-TYPE

The optical power received on the second stage of the amplifier. It applies to mid-stage access amplifiers only.

OBJECT-TYPE

The optical power transmitted at the output of the amplifier.

OBJECT-TYPE

The mid-stage insertion loss. This object is only applicable to OLAM type amplifiers.

OBJECT-TYPE

The effective gain level of the optical amplifier.

OBJECT-TYPE

The optical power transmitted at the output of the first stage of the amplifier. It applies to mid-stage access amplifiers only.

OBJECT-TYPE

The optical amplifier laser 1 current.

OBJECT-TYPE

The optical amplifier laser 2 current.

OBJECT-TYPE

The optical amplifier laser 1 power.

OBJECT-TYPE

The optical amplifier laser 2 power.

OBJECT-TYPE

The optical back reflection of the amplifier.

OBJECT-TYPE

The variable optical attenuation of the amplifier.

OBJECT-TYPE

The administrative status of the optical amplifier.

OBJECT-TYPE

The reported operational status of the optical amplifier.

OBJECT-TYPE

A textual list of qualifiers of the reported operational status of the optical amplifier.

OBJECT-TYPE

Specifies the auto-enable timer for the targeted optical amplifier. This value only applies if the oaAdminStatus object is set to autoEnabled. Otherwise, the value returned is 000-00. The supported range of values is 000-00 to 096-00.

OBJECT-TYPE

Indicates the time remaining on the auto-enable timer, if it is actively counting down. Otherwise, the value returned is 000-00.

OBJECT-TYPE

The desired mode of operation to which this optical amplifier is set.

OBJECT-TYPE

The effective gain (excluding ASE) set point. A default value is provided when the optical amplifier is created based on the optical amplifier type provisioned.

OBJECT-TYPE

The signal output power (excluding ASE) set point. A default value is provided when the optical amplifier is created based on the optical amplifier type provisioned.

OBJECT-TYPE

The desired tilt compensation to which this optical amplifier is set.

OBJECT-TYPE

The specific operational status of the amplifier.

OBJECT-TYPE

The actual operational status of the optical amplifier laser.

OBJECT-TYPE

Textual data recorded by the user to describe the provisioned optical amplifier in a manner useful to the user.

OBJECT-TYPE

Textual data recorded by the user to describe the provisioned optical amplifier in a manner useful to the user.

OBJECT-TYPE

An optional specification of the fiber type that interfaces with the optical amplifier.

OBJECT-TYPE

An optional indication of the WDM grid to which the link conforms.

OBJECT-TYPE

An optional indication of the number of channels that the link is carrying.

OBJECT-TYPE

A variable length text string for operating company use.

OBJECT-TYPE

A variable length text string for operating company use.

OBJECT-TYPE

A variable length text string for operating company use.

OBJECT-TYPE

The wavelength transmitted from the OA port. This object applies only to single channel amplifiers (sba, spa).

OBJECT-TYPE

Identifies the remote node and port to which the optical amplifier port is connected, in the format prescribed by the PSM network management system.

OBJECT-TYPE

Used to control the addition and deletion of entries in the optical amplifier table, which in turn controls provisioning and deprovisioning of optical amplifier facilities.

OBJECT-TYPE

This table contains one row for every provisioned optical transceiver on a wavelength translator, regenerator or manager card. Each row contains a list of attributes that pertain to the transceiver.

OBJECT-TYPE

The conceptual row object of the optical transceiver table.

OBJECT-TYPE

The specific type of wavelength conversion function of the circuit pack on which the transceiver is provisioned.

OBJECT-TYPE

The number of the shelf on which the transceiver is provisioned.

OBJECT-TYPE

The number of the slot within which the transceiver is provisioned.

OBJECT-TYPE

The number of the port on the circuit pack on which the transceiver is provisioned.

OBJECT-TYPE

This is the optical power received minimum threshold.

OBJECT-TYPE

This is the optical power received maximum threshold.

OBJECT-TYPE

This is the optical power transmitted minimum threshold.

OBJECT-TYPE

This is the optical power transmitted maximum threshold.

OBJECT-TYPE

The optical power received on the input of the transceiver.

OBJECT-TYPE

The optical power transmitted at the output of the transceiver.

OBJECT-TYPE

Indicates the type of protection switching event that has occured on an optical transceiver port.

OBJECT-TYPE

An optionally provisioned transceiver Product Equipment Code used to validate the physically present transceiver.

OBJECT-TYPE

The administrative status of the optical transceiver.

OBJECT-TYPE

The reported operational status of the optical transceiver.

OBJECT-TYPE

This is a textual list of qualifiers about the reported operational status of the optical transceiver.

OBJECT-TYPE

Specifies the auto-enable timer for the targeted optical transceiver. This value only applies if the xcvrAdminStatus object is set to autoEnabled. Otherwise, the value returned is 000-00.

OBJECT-TYPE

Indicates the time remaining on the auto-enable timer if it is actively counting down. Otherwise, the value returned is 000-00.

OBJECT-TYPE

The protocol of the service to be carried by the port. This is a mandatory object when a row of the transceiver table is created.

OBJECT-TYPE

The wavelength to be transmitted by the transceiver port. This is a mandatory object when a row of the transceiver table is created for ports that have a pluggable transceiver.

OBJECT-TYPE

An optionally provisioned part number used to validate the physically present transceiver.

OBJECT-TYPE

An optionally provisioned part number used to validate the physically present transceiver.

OBJECT-TYPE

An optionally provisioned part number used to validate the physically present transceiver.

OBJECT-TYPE

Indicates if the port is configured to report threshold crossing conditions for physical layer performance monitoring parameters.

OBJECT-TYPE

Indicates if the port is configured for Fault Propagation Shut Down.

OBJECT-TYPE

An indication of the operational status of the transceiver laser.

OBJECT-TYPE

Textual data recorded by the user to describe the provisioned optical transceiver in a manner useful to the user.

OBJECT-TYPE

Textual data recorded by the user to describe the provisioned optical transceiver in a manner useful to the user.

OBJECT-TYPE

An optional specification of the fiber type that interfaces to the optical transceiver.

OBJECT-TYPE

An optical indication of the WDM grid the link conforms.

OBJECT-TYPE

A variable length text string for operating company use.

OBJECT-TYPE

A variable length text string for operating company use.

OBJECT-TYPE

A variable length text string for operating company use.

OBJECT-TYPE

If specified, this attribute will describe the trace label to be used in the outgoing OTN or SONET/SDH trace.

OBJECT-TYPE

This attribute will describe the trace label that is expected to be received in the incoming OTN or SONET/SDH trace. If specified, this expected trace label will be compared to the actual value for xcvrReceivedTraceLabel, and a trace mismatch alarm will be raised if the two trace labels do not match.

OBJECT-TYPE

The actual received trace label on the incoming OTN or SONET/SDH trace.

OBJECT-TYPE

The Bit Error Rate threshold above which the Signal Degrade condition is raised.

OBJECT-TYPE

The loopback type that is currently active on the xcvr

OBJECT-TYPE

Identifies the remote node and port to which the transceiver port is connected, in the format prescribed by the PSM network management system.

OBJECT-TYPE

Used to control the addition and deletion of entries in the Transceiver table, which in turn controls provisioning and deprovisioning of optical transceiver facilities.

OBJECT-TYPE

This table contains one row for every provisioned active multiplexer-demultiplexer facility. AMD facilities include AMD line facilities and AMD channel facilities. Each row contains a list of attributes that pertain to one facility.

OBJECT-TYPE

The conceptual row object of the Active Mux-Demux table.

OBJECT-TYPE

The specific type of active multiplexer-demultiplexer circuit pack on which the facility is provisioned.

OBJECT-TYPE

The number of the shelf on which the active multiplexer-demultiplexer facility is provisioned.

OBJECT-TYPE

The number of the slot within which the active multiplexer-demultiplexer facility is provisioned.

OBJECT-TYPE

The number of the multiplexed wavelength line on the AMD circuit pack.

OBJECT-TYPE

Identifies a specific port on the identified line of the AMD circuit pack.

OBJECT-TYPE

This is the optical power received minimum threshold.

OBJECT-TYPE

This is the optical power received maximum threshold.

OBJECT-TYPE

This is the optical power transmitted target level.

OBJECT-TYPE

This is the optical power attenuation target level.

OBJECT-TYPE

The optical input power received for the channel.

OBJECT-TYPE

The optical power level transmitted for the channel.

OBJECT-TYPE

The optical power attenuation for the line.

OBJECT-TYPE

The administrative status of the AMD port.

OBJECT-TYPE

The reported operational status of the AMD port.

OBJECT-TYPE

This is a textual list of qualifiers about the reported operational status of the AMD port.

OBJECT-TYPE

Specifies the auto-enable timer for the targeted AMD port. This value only applies if the amdAdminStatus object is set to autoEnabled. Otherwise, the value returned is 000-00.

OBJECT-TYPE

Indicates the time remaining on the auto-enable timer if it is actively counting down. Otherwise, the value returned is 000-00.

OBJECT-TYPE

The wavelength transmitted from the AMD port. This object applies only to channel ports.

OBJECT-TYPE

Textual data recorded by the user to describe the provisioned optical transceiver in a manner useful to the user.

OBJECT-TYPE

Textual data recorded by the user to describe the provisioned optical transceiver in a manner useful to the user.

OBJECT-TYPE

An optional specification of the fiber type that interfaces to the AMD port.

OBJECT-TYPE

An optical indication of the WDM grid to which the AMD port link conforms.

OBJECT-TYPE

A variable length text string for operating company use.

OBJECT-TYPE

A variable length text string for operating company use.

OBJECT-TYPE

A variable length text string for operating company use.

OBJECT-TYPE

The active multiplexer-demultiplexer table RowStatus object is not readable or writeable because all entries in the AMD table are automatically created and deleted when the AMD circuit pack is created or deleted. This AMD row status object is used only in database change notifications to indicate if the row has been created or deleted.

OBJECT-TYPE

This table contains one row for each port on every provisioned passive circuit pack on the NE. Each list contains a list of attributes that pertain to the passive port.

OBJECT-TYPE

The conceptual row object of the passive circuit pack port table.

OBJECT-TYPE

The type of circuit pack on which the passive port is found.

OBJECT-TYPE

The number of the shelf on which the passive circuit pack port is provisioned.

OBJECT-TYPE

The number of the slot within which the passive circuit pack port is provisioned.

OBJECT-TYPE

Identifies the multiplexed multi-channel optical facility instance associated with the targeted passive port.

OBJECT-TYPE

Identifies the specific passive port on the circuit pack according to function.

OBJECT-TYPE

An optional name used to identify the passive circuit pack port facility.

OBJECT-TYPE

An optional identifier for the passive circuit pack port circuit.

OBJECT-TYPE

An optional specification of the fiber type interfacing the passive circuit pack port.

OBJECT-TYPE

An optional indication of the DWM grid that the link conforms to.

OBJECT-TYPE

An optional indication of the number of channels that the link is carrying. This field does not apply to individual channel type ports.

OBJECT-TYPE

An indication of the wavelength that the port is carrying.

OBJECT-TYPE

A variable length text string for operating company use.

OBJECT-TYPE

A variable length text string for operating company use.

OBJECT-TYPE

A variable length text string for operating company use.

OBJECT-TYPE

Identifies the remote node and port to which the passive card port is connected, in the format prescribed by the PSM network management system.

OBJECT-TYPE

The passive port table RowStatus object is not readable or writeable because all entries in the passive port table are automatically created and deleted when the circuit pack is created or deleted. This passive port row status object is used only in database change notifications to indicate if the row has been created or deleted.

OBJECT-TYPE

This table contains one row for every provisioned SONET OC-N facility on the system. Each row contains a list of attributes that pertain to the facility.

OBJECT-TYPE

The conceptual row object of the OC-N table.

OBJECT-TYPE

The specific type of OC-N signal which is provisioned.

OBJECT-TYPE

The number of the shelf on which the OC-N facility is provisioned.

OBJECT-TYPE

The number of the slot within which the OC-N facility is provisioned.

OBJECT-TYPE

The number of the port on the circuit pack on which the OC-N facility is provisioned.

OBJECT-TYPE

This is the optical power received minimum threshold.

OBJECT-TYPE

This is the optical power received maximum threshold.

OBJECT-TYPE

This is the optical power transmitted minimum threshold.

OBJECT-TYPE

This is the optical power transmitted maximum threshold.

OBJECT-TYPE

The optical power received on the input of the transceiver.

OBJECT-TYPE

The optical power transmitted at the output of the transceiver.

OBJECT-TYPE

The Bit Error Rate measured on the received signal.

OBJECT-TYPE

The Bit Error Rate threshold above which the Signal Degrade condition is raised.

OBJECT-TYPE

An optionally provisioned Product Equipment Code used to validate the physically present optical transceiver on the OC-N port.

OBJECT-TYPE

The administrative status of the OC-N facility.

OBJECT-TYPE

The reported operational status of the OC-N facility.

OBJECT-TYPE

This is a textual list of qualifiers about the reported operational status of the OC-N facility.

OBJECT-TYPE

Specifies the auto-enable timer for the targeted OC-N facility. This value only applies if the ocnAdminStatus object is set to autoEnabled. Otherwise, the value returned is 000-00.

OBJECT-TYPE

Indicates the time remaining on the auto-enable timer if it is actively counting down. Otherwise, the value returned is 000-00.

OBJECT-TYPE

The wavelength to be transmitted by the transceiver on the OC-N facility port. This is a mandatory object when a row of the OC-N table is created.

OBJECT-TYPE

An optionally provisioned part number used to validate the optical transceiver on the OC-N facility port.

OBJECT-TYPE

An optionally provisioned part number used to validate the optical transceiver on the OC-N facility port.

OBJECT-TYPE

An optionally provisioned part number used to validate the optical transceiver on the OC-N facility port.

OBJECT-TYPE

Indicates if the OC-N facility is configured to report threshold crossing conditions for physical layer performance monitoring parameters.

OBJECT-TYPE

An indication of the operational status of the transceiver laser on the OC-N facility port.

OBJECT-TYPE

Textual data recorded by the user to describe the provisioned OC-N facility in a manner useful to the user.

OBJECT-TYPE

An optional specification of the fiber type that interfaces to the OC-N facility port.

OBJECT-TYPE

A variable length text string for operating company use.

OBJECT-TYPE

Used to configure whether the transport overhead of the the SONET OC-N facility is to be handled transparently or if it is to be terminated and regenerated. This object only applies to OC-48 client facilities on the 10G MXP circuit pack and the OC-12 and OC-3 client facilities on the 8-port 2.5G MXP circuit pack.

OBJECT-TYPE

Used to configure the OTN configuration of the line port. If set to unmapped, there is no OTN digital wrapper added to the OC-192 or OC-48 facility. The odu1ToOtu2 and otu2 mapping is applicable to OC-192 line ports as follows: odu1ToOtu2 - the line port is configured as an OTN digitally wrapped OTU2 facility containing 4 ODU1 units. otu2 - the line port is configured as an OTN digitally wrapped OTU2 facility to which an OC-192 facility is directly mapped. The subOdu1ToOtu1 and otu1 mapping is applicable to OC-48 line ports as follows: subOdu1ToOtu1 - the line port is configured as an OTN digitally wrapped ODU1 facility containing 4 sub-ODU1 units. otu1 - the line port is configured as an OTN digitally wrapped OTU1 facility to which an OC-48 facility is directly mapped. This object applies only to the OC-192 line port of the 10G MXP circuit pack and the OC-48 line port of the 8-port 2.5G circuit pack.

OBJECT-TYPE

Indicates the type of protection switching event that has occured on an OC-N facility.

OBJECT-TYPE

Used to configure whether the Data Communications Channel (DCC) is transported transparently through the circuit pack. Specifically, this refers to the D1, D2 and D3 section DCC bytes. This object only applies to OC-48 client facilities on the 10G MXP circuit pack and the OC-12 client facilities on the 8-port 2.5G MXP circuit pack.

OBJECT-TYPE

Used to configure the STS1 channel number on which the DCC is transported. This object only applies to OC-48 client facilities on the 10G MXP circuit pack and the OC-12 client facilities on the 8-port 2.5G MXP circuit pack.

OBJECT-TYPE

Identifies the remote node and port to which the OC-n port is connected, in the format prescribed by the PSM network management system.

OBJECT-TYPE

Used to control the addition and deletion of entries in the OC-N table, which in turn controls provisioning and deprovisioning of OC-N facilities.

OBJECT-TYPE

This table contains one row for every created SONET STS-N facility on the system. Each row contains a list of attributes that pertain to the facility.

OBJECT-TYPE

The conceptual row object of the STS-N table.

OBJECT-TYPE

The specific type of STS-N signal which is created.

OBJECT-TYPE

The number of the shelf on which the STS-N facility exists.

OBJECT-TYPE

The number of the slot within which the STS-N facility exists.

OBJECT-TYPE

The number of the port on the circuit pack on which the STS-N facility exists.

OBJECT-TYPE

The stsn channel number within the port in which the STS-N facility exists.

OBJECT-TYPE

Indicates the type of protection switching event that has occured on an STS-N facility.

OBJECT-TYPE

The Bit Error Rate measured on the received channel.

OBJECT-TYPE

The Bit Error Rate threshold above which the Signal Degrade condition is raised.

OBJECT-TYPE

If the STS-N facility is configured as part of a protection grouping, this object indicates its protection status.

OBJECT-TYPE

This table contains one row for every provisioned SDH STM-N facility on the system. Each row contains a list of attributes that pertain to the facility.

OBJECT-TYPE

The conceptual row object of the STM-N table.

OBJECT-TYPE

The specific type of STM-N signal which is provisioned.

OBJECT-TYPE

The number of the shelf on which the STM-N facility is provisioned.

OBJECT-TYPE

The number of the slot within which the STM-N facility is provisioned.

OBJECT-TYPE

The number of the port on the circuit pack on which the STM-N facility is provisioned.

OBJECT-TYPE

This is the optical power received minimum threshold.

OBJECT-TYPE

This is the optical power received maximum threshold.

OBJECT-TYPE

This is the optical power transmitted minimum threshold.

OBJECT-TYPE

This is the optical power transmitted maximum threshold.

OBJECT-TYPE

The optical power received on the input of the transceiver.

OBJECT-TYPE

The optical power transmitted at the output of the transceiver.

OBJECT-TYPE

The Bit Error Rate measured on the received signal.

OBJECT-TYPE

The Bit Error Rate threshold above which the Signal Degrade condition is raised.

OBJECT-TYPE

An optionally provisioned Product Equipment Code used to validate the physically present optical transceiver on the STM-N port.

OBJECT-TYPE

The administrative status of the STM-N facility.

OBJECT-TYPE

The reported operational status of the STM-N facility.

OBJECT-TYPE

This is a textual list of qualifiers about the reported operational status of the STM-N facility.

OBJECT-TYPE

Specifies the auto-enable timer for the targeted STM-N facility. This value only applies if the stmnAdminStatus object is set to autoEnabled. Otherwise, the value returned is 000-00.

OBJECT-TYPE

Indicates the time remaining on the auto-enable timer if it is actively counting down. Otherwise, the value returned is 000-00.

OBJECT-TYPE

The wavelength to be transmitted by the transceiver on the STM-N facility port. This is a mandatory object when a row of the STM-N table is created.

OBJECT-TYPE

An optionally provisioned part number used to validate the optical transceiver on the STM-N facility port.

OBJECT-TYPE

An optionally provisioned part number used to validate the optical transceiver on the STM-N facility port.

OBJECT-TYPE

An optionally provisioned part number used to validate the optical transceiver on the STM-N facility port.

OBJECT-TYPE

Indicates if the STM-N facility is configured to report threshold crossing conditions for physical layer performance monitoring parameters.

OBJECT-TYPE

An indication of the operational status of the transceiver laser on the STM-N facility port.

OBJECT-TYPE

Textual data recorded by the user to describe the provisioned STM-N facility in a manner useful to the user.

OBJECT-TYPE

An optional specification of the fiber type that interfaces to the STM-N facility port.

OBJECT-TYPE

A variable length text string for operating company use.

OBJECT-TYPE

Used to configure whether the transport overhead of the the SDH STM-N facility is to be handled transparently or if it is to be terminated and regenerated. This object only applies to STM-16 client facilities on the 10G MXP circuit pack and the STM-4 and STM-1 client facilities on the 8-port 2.5G MXP circuit pack.

OBJECT-TYPE

Used to configure the OTN configuration of the line port. If set to unmapped, there is no OTN digital wrapper added to the STM-64 or STM-16 facility. The odu1ToOtu2 and otu2 mapping is applicable to STM-64 line ports as follows: odu1ToOtu2 - the line port is configured as an OTN digitally wrapped OTU2 facility containing 4 ODU1 units. otu2 - the line port is configured as an OTN digitally wrapped OTU2 facility to which an STM-64 facility is directly mapped. The subOdu1ToOtu1 and otu1 mapping is applicable to STM-16 line ports as follows: subOdu1ToOtu1 - the line port is configured as an OTN digitally wrapped ODU1 facility containing 4 sub-ODU1 units. otu1 - the line port is configured as an OTN digitally wrapped OTU1 facility to which an STM-16 facility is directly mapped. This object applies only to the STM-64 line port of the 10G MXP circuit pack and the STM-16 line port of the 8-port 2.5G circuit pack.

OBJECT-TYPE

Indicates the type of protection switching event that has occured on an STM-N facility.

OBJECT-TYPE

Used to configure whether the Data Communications Channel (DCC) is transported transparently through the circuit pack. Specifically, this refers to the D1, D2 and D3 section DCC bytes. This object only applies to STM-16 client facilities on the 10G MXP circuit pack and the STM-4 client facilities on the 8-port 2.5G MXP circuit pack.

OBJECT-TYPE

Used to configure the VC4 channel number on which the DCC is transported. This object only applies to STM-16 client facilities on the 10G MXP circuit pack and the STM-4 client facilities on the 8-port 2.5G MXP circuit pack.

OBJECT-TYPE

Identifies the remote node and port to which the STM-n port is connected, in the format prescribed by the PSM network management system.

OBJECT-TYPE

Used to control the addition and deletion of entries in the STM-N table, which in turn controls provisioning and deprovisioning of STM-N facilities.

OBJECT-TYPE

This table contains one row for every created SDH VC-N facility on the system. Each row contains a list of attributes that pertain to the facility.

OBJECT-TYPE

The conceptual row object of the VC-N table.

OBJECT-TYPE

The specific type of VC-N signal which is created.

OBJECT-TYPE

The number of the shelf on which the VC-N facility exists.

OBJECT-TYPE

The number of the slot within which the VC-N facility exists.

OBJECT-TYPE

The number of the port on the circuit pack on which the VC-N facility exists.

OBJECT-TYPE

The vcn channel number within the port in which the VC-N facility exists.

OBJECT-TYPE

Indicates the type of protection switching event that has occured on a VC-N facility.

OBJECT-TYPE

The Bit Error Rate measured on the received channel.

OBJECT-TYPE

The Bit Error Rate threshold above which the Signal Degrade condition is raised.

OBJECT-TYPE

If the VC-N facility is configured as part of a protection grouping, this object indicates its protection status.

OBJECT-TYPE

This table contains one row for every provisioned Gigabit Ethernet (GE) facility on the system. Each row contains a list of attributes that pertain to the facility.

OBJECT-TYPE

The conceptual row object of the GE table.

OBJECT-TYPE

The number of the shelf on which the GE facility is provisioned.

OBJECT-TYPE

The number of the slot within which the GE facility is provisioned.

OBJECT-TYPE

The number of the port on the circuit pack on which the GE facility is provisioned.

OBJECT-TYPE

This is the optical power received minimum threshold.

OBJECT-TYPE

This is the optical power received maximum threshold.

OBJECT-TYPE

This is the optical power transmitted minimum threshold.

OBJECT-TYPE

This is the optical power transmitted maximum threshold.

OBJECT-TYPE

The optical power received on the input of the transceiver.

OBJECT-TYPE

The optical power transmitted at the output of the transceiver.

OBJECT-TYPE

An optionally provisioned transceiver Product Equipment Code used to validate the physically present transceiver on the Gigabit Ethernet port.

OBJECT-TYPE

The administrative status of the Gigabit Ethernet facility.

OBJECT-TYPE

The reported operational status of the Gigabit Ethernet facility.

OBJECT-TYPE

This is a textual list of qualifiers about the reported operational status of the Gigabit Ethernet facility.

OBJECT-TYPE

Specifies the auto-enable timer for the targeted Gigabit Ethernet facility. This value only applies if the geAdminStatus object is set to autoEnabled. Otherwise, the value returned is 000-00.

OBJECT-TYPE

Indicates the time remaining on the auto-enable timer if it is actively counting down. Otherwise, the value returned is 000-00.

OBJECT-TYPE

The wavelength to be transmitted by the transceiver on the Gigabit Ethernet facility port. This is a mandatory object when a row of the Gigabit Ethernet table is created.

OBJECT-TYPE

An optionally provisioned part number used to validate the optical transceiver on the Gigabit Ethernet facility port.

OBJECT-TYPE

An optionally provisioned part number used to validate the optical transceiver on the Gigabit Ethernet facility port.

OBJECT-TYPE

An optionally provisioned part number used to validate the optical transceiver on the Gigabit Ethernet facility port.

OBJECT-TYPE

Indicates if the Gigabit Ethernet facility is configured to report threshold crossing conditions for physical layer performance monitoring parameters.

OBJECT-TYPE

Indicates if the Gigabit Ethernet facility is configured for Fault Propagation Shut Down.

OBJECT-TYPE

An indication of the operational status of the transceiver laser on the Gigabit Ethernet facility port.

OBJECT-TYPE

Textual data recorded by the user to describe the provisioned Gigabit Ethernet facility in a manner useful to the user.

OBJECT-TYPE

An optional specification of the fiber type that interfaces to the Gigabit Ethernet facility port.

OBJECT-TYPE

A variable length text string for operating company use.

OBJECT-TYPE

The speed of the Gigabit Ethernet facility link.

OBJECT-TYPE

The duplex mode of the Gigabit Ethernet facility interface.

OBJECT-TYPE

The configured media rate of the Gigabit Ethernet facility interface.

OBJECT-TYPE

The MTU size for the Gigabit Ethernet facility interface.

OBJECT-TYPE

The MAC address of the Gigabit Ethernet facility interface.

OBJECT-TYPE

Configures the mapping of GE facility port onto the line port using either framed or transparent general framing protocol.

OBJECT-TYPE

Configures the flow control setting of GE facility as transparent or locally enabled.

OBJECT-TYPE

Identifies the remote node and port to which the gigabit ethernet port is connected, in the format prescribed by the PSM network management system.

OBJECT-TYPE

Used to control the addition and deletion of entries in the Gigabit Ethernet table, which in turn controls provisioning and deprovisioning of Gigabit Ethernet facilities.

OBJECT-TYPE

This table contains one row for every provisioned Fast Ethernet (FE) facility on the system. Each row contains a list of attributes that pertain to the facility.

OBJECT-TYPE

The conceptual row object of the FE table.

OBJECT-TYPE

The number of the shelf on which the FE facility is provisioned.

OBJECT-TYPE

The number of the slot within which the FE facility is provisioned.

OBJECT-TYPE

The number of the port on the circuit pack on which the FE facility is provisioned.

OBJECT-TYPE

Textual data recorded by the user to describe the provisioned Fast Ethernet facility in a manner useful to the user.

OBJECT-TYPE

A variable length text string for operating company use.

OBJECT-TYPE

The speed of the Fast Ethernet facility link.

OBJECT-TYPE

The duplex mode of the Fast Ethernet facility interface.

OBJECT-TYPE

The configured media rate of the Fast Ethernet facility interface.

OBJECT-TYPE

The MTU size for the Fast Ethernet facility interface.

OBJECT-TYPE

The MAC address of the Fast Ethernet facility interface.

OBJECT-TYPE

Identifies the remote node and port to which the fast ethernet port is connected, in the format prescribed by the PSM network management system.

OBJECT-TYPE

Used to control the addition and deletion of entries in the Fast Ethernet table, which in turn controls provisioning and deprovisioning of Fast Ethernet facilities.

OBJECT-TYPE

This table contains one row for every provisioned Virtual Concatenation Group (VCG) enitity on the system. Each row contains a list of attributes that pertain to the VCG.

OBJECT-TYPE

The conceptual row object of the VCG table.

OBJECT-TYPE

The number of the shelf on which the VCG entity is located.

OBJECT-TYPE

The number of the slot within which the VCG entity is located.

OBJECT-TYPE

The number of the port on the circuit pack on which the VCG entity is located.

OBJECT-TYPE

The number of the VCG within the identified port.

OBJECT-TYPE

The format of the VCG.

OBJECT-TYPE

A textual listing of the time slot indices used for the VCG. The information is formatted as a comma-separated list of of individual time slot indices or time slot index ranges. For example, a value of 'X-Y,Z' indicates that the VCG includes all time slots in the range of X to Y, plus Z, when X, Y, and Z are all integers.

OBJECT-TYPE

Used to control the addition and deletion of entries in the VCG table, which in turn controls provisioning and deprovisioning of Virtual Concatenation groups. Manual creation and deletion of VCGs is supported only on the 10G MXP, as all VCGs on the 2.5G MXP are auto-created and deleted.

OBJECT-TYPE

This table contains one row for every provisioned fiber channel facility on the system. Each row contains a list of attributes that pertain to the facility.

OBJECT-TYPE

The conceptual row object of the fiber channel table.

OBJECT-TYPE

The number of the shelf on which the fiber channel facility is provisioned.

OBJECT-TYPE

The number of the slot within which the fiber channel facility is provisioned.

OBJECT-TYPE

The number of the port on the circuit pack on which the fiber channel facility is provisioned.

OBJECT-TYPE

The rate of the fiber channel signal which is provisioned.

OBJECT-TYPE

This is the optical power received minimum threshold.

OBJECT-TYPE

This is the optical power received maximum threshold.

OBJECT-TYPE

This is the optical power transmitted minimum threshold.

OBJECT-TYPE

This is the optical power transmitted maximum threshold.

OBJECT-TYPE

The optical power received on the input of the transceiver.

OBJECT-TYPE

The optical power transmitted at the output of the transceiver.

OBJECT-TYPE

An optionally provisioned Product Equipment Code used to validate the physically present optical transceiver on the fiber channel port.

OBJECT-TYPE

The administrative status of the fiber channel facility.

OBJECT-TYPE

The reported operational status of the fiber channel facility.

OBJECT-TYPE

This is a textual list of qualifiers about the reported operational status of the fiber channel facility.

OBJECT-TYPE

Specifies the auto-enable timer for the targeted fiber channel facility. This value only applies if the fcAdminStatus object is set to autoEnabled. Otherwise, the value returned is 000-00.

OBJECT-TYPE

Indicates the time remaining on the auto-enable timer if it is actively counting down. Otherwise, the value returned is 000-00.

OBJECT-TYPE

The wavelength to be transmitted by the transceiver on the fiber channel facility port. This is a mandatory object when a row of the fiber channel table is created.

OBJECT-TYPE

An optionally provisioned part number used to validate the optical transceiver on the fiber channel facility port.

OBJECT-TYPE

An optionally provisioned part number used to validate the optical transceiver on the fiber channel facility port.

OBJECT-TYPE

An optionally provisioned part number used to validate the optical transceiver on the fiber channel facility port.

OBJECT-TYPE

Indicates if the fiber channel facility is configured to report threshold crossing conditions for physical layer performance monitoring parameters.

OBJECT-TYPE

Indicates if the Fiber Channel facility is configured for Fault Propagation Shut Down.

OBJECT-TYPE

An indication of the operational status of the transceiver laser on the fiber channel facility port.

OBJECT-TYPE

Textual data recorded by the user to describe the provisioned fiber channel facility in a manner useful to the user.

OBJECT-TYPE

An optional specification of the fiber type that interfaces to the fiber channel facility port.

OBJECT-TYPE

A variable length text string for operating company use.

OBJECT-TYPE

Configures the mapping of fiber channel facility port onto the line port using GFP. Only the transparent mapping is supported for fiber channel facilities.

OBJECT-TYPE

Identifies the remote node and port to which the fiber channel port is connected, in the format prescribed by the PSM network management system.

OBJECT-TYPE

Used to control the addition and deletion of entries in the fiber channel table, which in turn controls provisioning and deprovisioning of fiber channel facilities.

OBJECT-TYPE

This table contains one row for every provisioned Ethernet facility on the system. Each row contains a list of attributes that pertain to the facility.

OBJECT-TYPE

The conceptual row object of the ethIntfTable table.

OBJECT-TYPE

The number of the shelf in which the Ethernet facility resides.

OBJECT-TYPE

The number of the slot in which the Ethernet facility resides.

OBJECT-TYPE

The type of the port on the circuit pack.

OBJECT-TYPE

The number of the port on the circuit pack on which the ethernet facility is provisioned.

OBJECT-TYPE

This is the optical power received minimum threshold.

OBJECT-TYPE

This is the optical power received maximum threshold.

OBJECT-TYPE

This is the optical power transmitted minimum threshold.

OBJECT-TYPE

This is the optical power transmitted maximum threshold.

OBJECT-TYPE

The optical power received on the input of the transceiver.

OBJECT-TYPE

The optical power transmitted at the output of the transceiver.

OBJECT-TYPE

An optionally provisioned transceiver Product Equipment Code used to validate the physically present transceiver on the Ethernet port.

OBJECT-TYPE

The administrative status of the Ethernet facility.

OBJECT-TYPE

The reported operational status of the Ethernet facility.

OBJECT-TYPE

This is a textual list of qualifiers about the reported operational status of the Ethernet facility.

OBJECT-TYPE

Specifies the auto-enable timer for the targeted Ethernet facility. This value only applies if the AdminStatus object is set to autoEnabled. Otherwise, the value returned is 000-00.

OBJECT-TYPE

Indicates the time remaining on the auto-enable timer if it is actively counting down. Otherwise, the value returned is 000-00.

OBJECT-TYPE

The wavelength to be transmitted by the transceiver on the Gigabit Ethernet facility port. This is a mandatory object when a row of the Ethernet table is created.

OBJECT-TYPE

An optionally provisioned part number used to validate the optical transceiver on the Ethernet facility port.

OBJECT-TYPE

An optionally provisioned part number used to validate the optical transceiver on the Ethernet facility port.

OBJECT-TYPE

An optionally provisioned part number used to validate the optical transceiver on the Ethernet facility port.

OBJECT-TYPE

Indicates if the Ethernet facility is configured to report threshold crossing conditions for physical layer performance monitoring parameters.

OBJECT-TYPE

Indicates if the Ethernet facility is configured for Fault Propagation Shut Down.

OBJECT-TYPE

An indication of the operational status of the transceiver laser on the Ethernet facility port.

OBJECT-TYPE

Textual data recorded by the user to describe the provisioned facility in a manner useful to the user.

OBJECT-TYPE

An optional specification of the fiber type that interfaces to the Ethernet facility port.

OBJECT-TYPE

A variable length text string for operating company use.

OBJECT-TYPE

The speed of the Ethernet facility link. This object is mandatory to create a new facility and determines the type of interface, based on speed.

OBJECT-TYPE

The duplex mode of the Ethernet facility interface.

OBJECT-TYPE

The configured media rate of the Ethernet facility interface. For 10 GE interfaces, the media rate can only be autoNegotiated.

OBJECT-TYPE

The MTU size for the Ethernet facility interface.

OBJECT-TYPE

This object provides the link status information regarding the particular interface.

OBJECT-TYPE

This object provides the information regarding the LAG Id of the particular interface.

OBJECT-TYPE

This object provides the information for lag port priority of the particular interface.

OBJECT-TYPE

The Signal Degrade Bit Error Ratio (SDBER) is used to configure the error rate threshold above which a Signal Degrade is declared.

OBJECT-TYPE

The MAC address of the interface.

OBJECT-TYPE

For 10 GE interfaces, both 10 GE LAN PHY and OTU2 encapsulated 10GE LAN PHY will be supported. The line mapping attribute allow provisioning of either of the protocol. This attributes applies to 10 GE interfaces only. When a 10 GE interface is configured as a stacking port, this field is set to stacking. NOTE: This parameter does not apply to gigabitEthernet type interfaces, attempts to set this for gigE port types will fail. Reading this object for non-10GigE interfaces will return notApplicable.

OBJECT-TYPE

For 10G in OTU2 line-mapping mode, this object specifies the error correction mode. For interfaces in tenlanphy line-mapping mode, this object must be none. Attempts to set it to any other value while in tenglanphy mode will fail. NOTE: This parameter does not apply to gigabitEthernet type interfaces, attempts to set this for gigE port types will fail.

OBJECT-TYPE

Used to perform a loopback operation on a transceiver facility as follows: - oprLpbk: operates a loopback on the transceiver - rlsLpbk: causes a previously invoked loopback to be released When read, this object returns noOp.

OBJECT-TYPE

Identifies the remote node and port to which the PVX ethernet port is connected, in the format prescribed by the PSM network management system.

OBJECT-TYPE

Mirror configuration for the physical ethernet port

OBJECT-TYPE

The administratively desired status of the local LLDP agent. If the associated ethIntfLldpAdminStatus object has a value of 'enabled(1)', then the LLDP agent will transmit and receive LLDP frames on this port. If the associated ethIntfLldpAdminStatus object has a value of 'disabled(2)', then LLDP agent will not transmit or receive LLDP frames on this port. If there is remote systems information which is received on this port and stored in other tables, before the port's ethIntfLldpAdminStatus becomes disabled, then the information will naturally age out.

OBJECT-TYPE

The type of encoding used to identify the chassis associated with the remote system.

OBJECT-TYPE

The string value used to identify the chassis component associated with the remote system.

OBJECT-TYPE

The type of port identifier encoding used in the associated 'ethIntfLldpRemPortId' object.

OBJECT-TYPE

The string value used to identify the port component associated with the remote system.

OBJECT-TYPE

Count of the Ethernet facility operational state changes sinse last reboot

OBJECT-TYPE

Used to control the addition and deletion of entries in the Ethernet table, which in turn controls provisioning and deprovisioning of Ethernet facilities.

OBJECT-TYPE

This table contains one row for every ODU-N facility on the system.

OBJECT-TYPE

The conceptual row object of the ODU-N table.

OBJECT-TYPE

The specific type of ODU-N which is provisioned.

OBJECT-TYPE

The number of the shelf on which the ODU-N facility is provisioned.

OBJECT-TYPE

The number of the slot within which the ODU-N facility is provisioned.

OBJECT-TYPE

The number of the port on the circuit pack on which the ODU-N facility is provisioned.

OBJECT-TYPE

The ODU-N channel number within the port in which the ODU-N facility exists.

OBJECT-TYPE

This table contains one row for every provisioned Bit Rate Independent (BRI) facility on the system. Each row contains a list of attributes that pertain to the facility.

OBJECT-TYPE

The conceptual row object of the BRI table.

OBJECT-TYPE

The number of the shelf on which the BRI facility is provisioned.

OBJECT-TYPE

The number of the slot within which the BRI facility is provisioned.

OBJECT-TYPE

The number of the port on the circuit pack on which the BRI facility is provisioned.

OBJECT-TYPE

The protocol of the BRI signal which is provisioned.

OBJECT-TYPE

This is the optical power received minimum threshold.

OBJECT-TYPE

This is the optical power received maximum threshold.

OBJECT-TYPE

This is the optical power transmitted minimum threshold.

OBJECT-TYPE

This is the optical power transmitted maximum threshold.

OBJECT-TYPE

The optical power received on the input of the transceiver.

OBJECT-TYPE

The optical power transmitted at the output of the transceiver.

OBJECT-TYPE

An optionally provisioned Product Equipment Code used to validate the physically present optical transceiver on the BRI port.

OBJECT-TYPE

The administrative status of the BRI facility.

OBJECT-TYPE

The reported operational status of the BRI facility.

OBJECT-TYPE

This is a textual list of qualifiers about the reported operational status of the BRI facility.

OBJECT-TYPE

Specifies the auto-enable timer for the targeted BRI facility. This value only applies if the briAdminStatus object is set to autoEnabled. Otherwise, the value returned is 000-00.

OBJECT-TYPE

Indicates the time remaining on the auto-enable timer if it is actively counting down. Otherwise, the value returned is 000-00.

OBJECT-TYPE

The wavelength to be transmitted by the transceiver on the BRI facility port. This is a mandatory object when a row of the fiber channel table is created.

OBJECT-TYPE

An optionally provisioned part number used to validate the optical transceiver on the BRI facility port.

OBJECT-TYPE

An optionally provisioned part number used to validate the optical transceiver on the BRI facility port.

OBJECT-TYPE

An optionally provisioned part number used to validate the optical transceiver on the BRI facility port.

OBJECT-TYPE

Indicates if the BRI facility is configured to report threshold crossing conditions for physical layer performance monitoring parameters.

OBJECT-TYPE

An indication of the operational status of the transceiver laser on the BRI facility port.

OBJECT-TYPE

Textual data recorded by the user to describe the provisioned BRI facility in a manner useful to the user.

OBJECT-TYPE

An optional specification of the fiber type that interfaces to the BRI facility port.

OBJECT-TYPE

A variable length text string for operating company use.

OBJECT-TYPE

The bit rate transmitted by the BRI facility port in Mbps.

OBJECT-TYPE

Identifies the remote node and port to which the Bitrate Independent port is connected, in the format prescribed by the PSM network management system.

OBJECT-TYPE

Used to control the addition and deletion of entries in the BRI table, which in turn controls provisioning and deprovisioning of BRI facilities.

OBJECT-IDENTITY

OBJECT-TYPE

This table contains one row for every provisioned optical supervisory channel interface on the NE. Each row contains a list of attributes that pertain to the OSC.

OBJECT-TYPE

The conceptual row object of the optical supervisory channel table.

OBJECT-TYPE

The number of the shelf on which the OSC is provisioned.

OBJECT-TYPE

The number of the slot in which the OSC is provisioned.

OBJECT-TYPE

The number of the port on the circuit pack on which the OSC is provisioned.

OBJECT-TYPE

The administrative status of the OSC interface.

OBJECT-TYPE

The reported operational status of the OSC interface.

OBJECT-TYPE

A textual list of qualifiers for the reported operational status of the OSC interface.

OBJECT-TYPE

A variable length text string for operating company use.

OBJECT-TYPE

The type of physical communication medium attached to the OSC interface.

OBJECT-TYPE

Indicates whether or not the OSC interface is the type that requires an IP address to be assigned.

OBJECT-TYPE

The speed of the OSC link.

OBJECT-TYPE

The duplex mode of the OSC interface.

OBJECT-TYPE

The configured media rate of the OSC interface.

OBJECT-TYPE

The MTU size for the OSC interface.

OBJECT-TYPE

The MAC address of the OSC interface.

OBJECT-TYPE

The IP Address of the OSC interface. A value of 0.0.0.0 indicates that the interface is not assigned an IP address.

OBJECT-TYPE

The IP Subnet Mask of the OSC interface.

OBJECT-TYPE

The IP broadcast address of the OSC interface.

OBJECT-TYPE

Used to control the addition and deletion of entries in the OSC table, which in turn controls provisioning and deprovisioning of OSC interfaces.

OBJECT-TYPE

This table contains one row for every network management interface on the NE. Each row contains a list of attributes that pertain to the interface.

OBJECT-TYPE

The conceptual row object of the network management interface table.

OBJECT-TYPE

Identifies the specific management interface.

OBJECT-TYPE

The administrative status of the management interface.

OBJECT-TYPE

The reported operational status of the management interface.

OBJECT-TYPE

A textual list of qualifiers for the reported operational status of the management interface.

OBJECT-TYPE

The IP Address of the management interface.

OBJECT-TYPE

The IP Subnet Mask of the management interface.

OBJECT-TYPE

The IP broadcast address of the management interface.

OBJECT-TYPE

A variable length text string for operating company use.

OBJECT-TYPE

The type of physical communication medium attached to the management interface.

OBJECT-TYPE

Indicates whether or not the management interface is the type that requires an IP address to be assigned.

OBJECT-TYPE

The speed of the management interface link.

OBJECT-TYPE

The duplex mode of the management interface.

OBJECT-TYPE

The configured media rate of the management interface.

OBJECT-TYPE

The MTU size for this management interface.

OBJECT-TYPE

The MAC address of the management interface.

OBJECT-TYPE

A table of serial communication ports on the network element. Each row contains a list of attributes that pertain to a given serial port.

OBJECT-TYPE

The conceptual row object for the serial port table.

OBJECT-TYPE

The serial port instance on the NE.

OBJECT-TYPE

The baud rate of the serial port.

OBJECT-TYPE

The number of data bits of the serial port.

OBJECT-TYPE

The parity value of the serial port.

OBJECT-TYPE

The number of stop bits of the serial port.

OBJECT-TYPE

A table of GCC0 configuration information. This table contains one row for every provisioned GCC0.

OBJECT-TYPE

A conceptual row that contains GCC0 configuration information of an interface. Each instance must correspond to an instance of an OTN Port capable of supporting GCC. Instances of this conceptual row persist across agent restarts.

OBJECT-TYPE

The specific type of circuit pack provisioned.

OBJECT-TYPE

The number of the shelf on which the gcc0 is provisioned.

OBJECT-TYPE

The number of the slot in which the gcc0 is provisioned.

OBJECT-TYPE

The number of the port on the circuit pack on which the gcc0 provisioned.

OBJECT-TYPE

The desired mode to which the gcc0 is to be provisioned.

OBJECT-TYPE

The administrative status of the gcc.

OBJECT-TYPE

The reported operational status of the gcc.

OBJECT-TYPE

A textual list of qualifiers of the reported operational status of the gcc.

OBJECT-TYPE

This columnar object is used for creating and deleting a conceptual row of the gcc0 config table.

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

A number indentifying a entity smaller than and contained in a port. At this time, this value is unused and must be zero.

OBJECT-TYPE

The reported operational status of the IP Interface.

OBJECT-TYPE

A textual list of qualifiers for the reported operational status of the IP Interface

OBJECT-TYPE

OBJECT-TYPE

Set to true if this is a numbered interface and false if it is unnumbered.

OBJECT-TYPE

The type of addresses (v4/v6) used in this row of this MIB. Currently only ipv4 is allowed in this table.

OBJECT-TYPE

The IP Address associated with the interface.

OBJECT-TYPE

The sub-net mask associated with the interface.

OBJECT-TYPE

Not currently implemented.

OBJECT-TYPE

A string describing the interface.

OBJECT-TYPE

The MAC address associated with the interface, if applicable. All zeros for a non-MAC interface.

OBJECT-TYPE

OBJECT-TYPE

A value describing the type of interface.

OBJECT-TYPE

The broadcast address associated with the interface.

OBJECT-TYPE

OBJECT-TYPE

Is the interface full or half-duplex?

OBJECT-TYPE

The Maximum Transmission Unit for the interface.

OBJECT-TYPE

OBJECT-TYPE

The gateway IP address associated with the interface.

OBJECT-TYPE

This columnar object is used for creating and deleting a conceptual row of the ipExtIntf table.

OBJECT-IDENTITY

OBJECT-TYPE

A table of current performance monitoring statistics collected for the optical amplifier facilities on the NE.

OBJECT-TYPE

The row entry object of the optical amplifier current performance monitoring table. Each row of this table contains a full set of PM statistics and related data for a current measurement interval for a given optical amplifier.

OBJECT-TYPE

The type of the optical amplifier targeted for PM retrieval.

OBJECT-TYPE

The number of the shelf on which the amplifier targeted for PMs is provisioned.

OBJECT-TYPE

The number of the slot within which the optical amplifier targeted for PMs is provisioned.

OBJECT-TYPE

The number of the amplifier port on which the circuit pack for PMs is targeted.

OBJECT-TYPE

The type of PM bin according to interval length.

OBJECT-TYPE

The optical amplifier case temperature.

OBJECT-TYPE

The date and time stamp of the case temperature value.

OBJECT-TYPE

Indicates the validity of the provided case temperature value.

OBJECT-TYPE

The optical amplifier laser 1 temperature.

OBJECT-TYPE

The date and time stamp of the laser 1 temperature value.

OBJECT-TYPE

Indicates the validity of the provided laser 1 temperature value.

OBJECT-TYPE

The optical amplifier laser 2 temperature.

OBJECT-TYPE

The date and time stamp of the laser 2 temperature value.

OBJECT-TYPE

Indicates the validity of the provided laser 2 temperature value.

OBJECT-TYPE

The optical power received on the input of the amplifer.

OBJECT-TYPE

The date and time stamp of the optical power received value.

OBJECT-TYPE

Indicates the validity of the provided optical power received value.

OBJECT-TYPE

The optical power received on the input of the second stage of the amplifier.

OBJECT-TYPE

The date and time stamp of the second stage input optical power received value.

OBJECT-TYPE

Indicates the validity of the provided second stage input optical power received value.

OBJECT-TYPE

The optical power transmitted at the output of the amplifier.

OBJECT-TYPE

The date and time stamp of the optical power transmitted value.

OBJECT-TYPE

Indicates the validity of the provided optical power transmitted value.

OBJECT-TYPE

The mid-stage insertion loss.

OBJECT-TYPE

The date and time stamp of the mid-stage insertion loss value.

OBJECT-TYPE

Indicates the validity of the provided mid-stage insertion loss value.

OBJECT-TYPE

The effective gain of the optical amplifier. This reading is compensated for amplified spontaneous emissions.

OBJECT-TYPE

The date and time stamp of the effective gain value.

OBJECT-TYPE

Indicates the validity of the provided effective gain value.

OBJECT-TYPE

The optical power transmitted at the output of the first stage of the amplifier.

OBJECT-TYPE

The date and time stamp of the first stage output optical power transmitted value.

OBJECT-TYPE

Indicates the validity of the provided first stage output optical power transmitted value.

OBJECT-TYPE

The optical amplifier laser 1 current.

OBJECT-TYPE

The date and time stamp of the laser 1 current value.

OBJECT-TYPE

Indicates the validity of the provided laser 1 current value.

OBJECT-TYPE

The optical amplifier laser 2 current.

OBJECT-TYPE

The date and time stamp of the laser 2 current value.

OBJECT-TYPE

Indicates the validity of the provided laser 2 current value.

OBJECT-TYPE

The optical amplifier laser 1 power.

OBJECT-TYPE

The date and time stamp of the laser 1 power value.

OBJECT-TYPE

Indicates the validity of the provided laser 1 power value.

OBJECT-TYPE

The optical amplifier laser 2 power.

OBJECT-TYPE

The date and time stamp of the laser 2 power value.

OBJECT-TYPE

Indicates the validity of the provided laser 2 power value.

OBJECT-TYPE

The back reflected optical power measured at the output of the second stage of the optical amplifier.

OBJECT-TYPE

The date and time stamp of the optical back reflection value.

OBJECT-TYPE

Indicates the validity of the provided optical back reflection value.

OBJECT-TYPE

The variable optical attenuation of the amplifier.

OBJECT-TYPE

The date and time stamp of the variable optical attenuation value.

OBJECT-TYPE

Indicates the validity of the provided variable optical attenuation value.

OBJECT-TYPE

A table of historical performance monitoring statistics collected for the optical amplifier facilities on the NE.

OBJECT-TYPE

The row entry object of the optical amplifier historical performance monitoring table. Each row of this table contains a full set of PM statistics and related data for a historical measurement interval for a given optical amplifier.

OBJECT-TYPE

The type of the optical amplifier targeted for PM retrieval.

OBJECT-TYPE

The number of the shelf on which the amplifier targeted for PMs is provisioned.

OBJECT-TYPE

The number of the slot within which the optical amplifier targeted for PMs is provisioned.

OBJECT-TYPE

The number of the amplifier port on the circuit pack targeted for PMs.

OBJECT-TYPE

The type of PM bin according to interval length.

OBJECT-TYPE

The specific PM bin number. The range is 1..96 for 15-minute bins, and for 1-day historical bins, the value is 1.

OBJECT-TYPE

The optical amplifier case temperature.

OBJECT-TYPE

The date and time stamp of the case temperature value.

OBJECT-TYPE

Indicates the validity of the provided case temperature value.

OBJECT-TYPE

The optical amplifier laser 1 temperature.

OBJECT-TYPE

The date and time stamp of the laser 1 temperature value.

OBJECT-TYPE

Indicates the validity of the provided laser 1 temperature value.

OBJECT-TYPE

The optical amplifier laser 2 temperature.

OBJECT-TYPE

The date and time stamp of the laser 2 temperature value.

OBJECT-TYPE

Indicates the validity of the provided laser 2 temperature value.

OBJECT-TYPE

The optical power received on the input of the amplifer.

OBJECT-TYPE

The date and time stamp of the optical power received value.

OBJECT-TYPE

Indicates the validity of the provided optical power received value.

OBJECT-TYPE

The optical power received on the input of the second stage of the amplifier.

OBJECT-TYPE

The date and time stamp of the second stage input optical power received value.

OBJECT-TYPE

Indicates the validity of the provided second stage input optical power received value.

OBJECT-TYPE

The optical power transmitted at the output of the amplifier.

OBJECT-TYPE

The date and time stamp of the optical power transmitted value.

OBJECT-TYPE

Indicates the validity of the provided optical power transmitted value.

OBJECT-TYPE

The mid-stage insertion loss.

OBJECT-TYPE

The date and time stamp of the mid-stage insertion loss value.

OBJECT-TYPE

Indicates the validity of the provided mid-stage insertion loss value.

OBJECT-TYPE

The effective gain of the optical amplifier. This reading is compensated for amplified spontaneous emissions.

OBJECT-TYPE

The date and time stamp of the effective gain value.

OBJECT-TYPE

Indicates the validity of the provided effective gain value.

OBJECT-TYPE

The optical power transmitted at the output of the first stage of the amplifier.

OBJECT-TYPE

The date and time stamp of the first stage output optical power transmitted value.

OBJECT-TYPE

Indicates the validity of the provided first stage output optical power transmitted value.

OBJECT-TYPE

The optical amplifier laser 1 current.

OBJECT-TYPE

The date and time stamp of the laser 1 current value.

OBJECT-TYPE

Indicates the validity of the provided laser 1 current value.

OBJECT-TYPE

The optical amplifier laser 2 current.

OBJECT-TYPE

The date and time stamp of the laser 2 current value.

OBJECT-TYPE

Indicates the validity of the provided laser 2 current value.

OBJECT-TYPE

The optical amplifier laser 1 power.

OBJECT-TYPE

The date and time stamp of the laser 1 power value.

OBJECT-TYPE

Indicates the validity of the provided laser 1 power value.

OBJECT-TYPE

The optical amplifier laser 2 power.

OBJECT-TYPE

The date and time stamp of the laser 2 power value.

OBJECT-TYPE

Indicates the validity of the provided laser 2 power value.

OBJECT-TYPE

The back reflected optical power measured at the output of the second stage of the optical amplifier.

OBJECT-TYPE

The date and time stamp of the optical back reflection value.

OBJECT-TYPE

Indicates the validity of the provided optical back reflection value.

OBJECT-TYPE

The variable optical attenuation of the amplifier.

OBJECT-TYPE

The date and time stamp of the variable optical attenuation value.

OBJECT-TYPE

Indicates the validity of the provided variable optical attenuation value.

OBJECT-TYPE

A table of current performance monitoring statistics collected for the optical transceiver facilities on the NE.

OBJECT-TYPE

The row entry object of the optical transceiver current performance monitoring table. Each row of this table contains a full set of PM statistics and related data for a current measurement interval for a given optical transceiver.

OBJECT-TYPE

The type of the optical transceiver targeted for PMs.

OBJECT-TYPE

The shelf number on which the optical transceiver targeted for PMs is provisioned.

OBJECT-TYPE

The slot number on which the optical transceiver targeted for PMs is provisioned.

OBJECT-TYPE

The optical transceiver port number on the circuit pack that is targeted for PMs.

OBJECT-TYPE

The type of PM bin according to interval length.

OBJECT-TYPE

The optical power received on the input of the transceiver.

OBJECT-TYPE

The date and time stamp of the optical power received value.

OBJECT-TYPE

Indicates the validity of the provided optical power received value.

OBJECT-TYPE

The optical power transmitted at the output of the transceiver.

OBJECT-TYPE

The date and time stamp of the optical power transmitted value.

OBJECT-TYPE

Indicates the validity of the provided optical power transmitted value.

OBJECT-TYPE

The optical transceiver temperature.

OBJECT-TYPE

The date and time stamp of the temperature value.

OBJECT-TYPE

Indicates the validity of the provided temperature value.

OBJECT-TYPE

The transceiver supply voltage.

OBJECT-TYPE

The date and time stamp of the supply voltage value.

OBJECT-TYPE

Indicates the validity of the provided supply voltage value.

OBJECT-TYPE

The transceiver laser bias current.

OBJECT-TYPE

The date and time stamp of the laser bias current value.

OBJECT-TYPE

Indicates the validity of the provided laser bias current value.

OBJECT-TYPE

The count of coding violations at the section layer. This object applies only to transciever ports provisioned for a SONET OC-N protocol.

OBJECT-TYPE

The date and time stamp of the section layer coding violations value.

OBJECT-TYPE

Indicates the validity of the provided section layer coding violations value.

OBJECT-TYPE

The count of errored seconds at the section layer. This object applies only to transciever ports provisioned for a SONET OC-N protocol.

OBJECT-TYPE

The date and time stamp of the section layer errored seconds value.

OBJECT-TYPE

Indicates the validity of the provided section layer errored seconds value.

OBJECT-TYPE

The count of severely errored seconds at the section layer. This object applies only to transciever ports provisioned for a SONET OC-N protocol.

OBJECT-TYPE

The date and time stamp of the section layer severely errored seconds value.

OBJECT-TYPE

Indicates the validity of the provided section layer severely errored seconds value.

OBJECT-TYPE

The count of severely errored framing seconds at the section layer. This object applies only to transciever ports provisioned for a SONET OC-N protocol.

OBJECT-TYPE

The date and time stamp of the section layer severely errored framing seconds value.

OBJECT-TYPE

Indicates the validity of the provided section layer severely errored framing seconds value.

OBJECT-TYPE

The count of regenerator section errored blocks. This object applies only to transciever ports provisioned for a SDH STM-N protocol.

OBJECT-TYPE

The date and time stamp of the regenerator section errored blocks value.

OBJECT-TYPE

Indicates the validity of the provided regenerator section errored blocks value.

OBJECT-TYPE

The count of regenerator section background block errors. This object applies only to transciever ports provisioned for a SDH STM-N protocol.

OBJECT-TYPE

The date and time stamp of the regenerator section background block errors value.

OBJECT-TYPE

Indicates the validity of the provided regenerator section background block errors value.

OBJECT-TYPE

The count of regenerator section errored seconds. This object applies only to transciever ports provisioned for a SDH STM-N protocol.

OBJECT-TYPE

The date and time stamp of the regenerator section errored seconds value.

OBJECT-TYPE

Indicates the validity of the provided regenerator section errored seconds value.

OBJECT-TYPE

The count of regenerator section severely errored seconds. This object applies only to transciever ports provisioned for a SDH STM-N protocol.

OBJECT-TYPE

The date and time stamp of the regenerator section severely errored seconds value.

OBJECT-TYPE

Indicates the validity of the provided regenerator section severely errored seconds value.

OBJECT-TYPE

The count of regenerator section out-of-frame seconds. This object applies only to transciever ports provisioned for a SDH STM-N protocol.

OBJECT-TYPE

The date and time stamp of the regenerator section out-of-frame seconds value.

OBJECT-TYPE

Indicates the validity of the provided regenerator section out-of-frame seconds value.

OBJECT-TYPE

The count of coding violations. This object applies only to transciever ports provisioned for the gigabit ethernet protocol or a fiber channel protocol.

OBJECT-TYPE

The date and time stamp of the coding violations value.

OBJECT-TYPE

Indicates the validity of the provided coding violations value.

OBJECT-TYPE

The count of errored seconds. This object applies only to transciever ports provisioned for an ethernet protocol or a fiber channel protocol.

OBJECT-TYPE

The date and time stamp of the errored seconds value.

OBJECT-TYPE

Indicates the validity of the provided errored seconds value.

OBJECT-TYPE

The count of severely errored seconds. This object applies only to transciever ports provisioned for an ethernet protocol or a fiber channel protocol.

OBJECT-TYPE

The date and time stamp of the severely errored seconds value.

OBJECT-TYPE

Indicates the validity of the provided severely errored seconds value.

OBJECT-TYPE

The count of invalid blocks. This object applies only to transciever ports provisioned for the 10 gigabit ethernet LAN protocol.

OBJECT-TYPE

The date and time stamp of the invalid blocks value.

OBJECT-TYPE

Indicates the validity of the provided invalid blocks value.

OBJECT-TYPE

The count of the number of bits corrected. This object applies only to transciever ports provisioned for a protocol that includes Forward Error Correction (FEC).

OBJECT-TYPE

The date and time stamp of the number of bits corrected value.

OBJECT-TYPE

Indicates the validity of the provided number of bits corrected value.

OBJECT-TYPE

The count of the number of bytes corrected. This object applies only to transciever ports provisioned for a protocol that includes Forward Error Correction (FEC).

OBJECT-TYPE

The date and time stamp of the number of bytes corrected value.

OBJECT-TYPE

Indicates the validity of the provided number of bytes corrected value.

OBJECT-TYPE

The count of uncorrectable codewords. This object applies only to transciever ports provisioned for a protocol that includes Forward Error Correction (FEC).

OBJECT-TYPE

The date and time stamp of the uncorrectable codewords value.

OBJECT-TYPE

Indicates the validity of the provided uncorrectable codewords value.

OBJECT-TYPE

The total number of bytes of data (including those in bad frames) received (excluding framing bits but including FCS octets). This object applies only to transceiver ports provisioned for the 10 gigabit ethernet LAN protocol.

OBJECT-TYPE

The date and time stamp of the received bytes count value.

OBJECT-TYPE

Indicates the validity of the provided received bytes count value.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMTBYCRXValue object to 0.

OBJECT-TYPE

The total number of received frames (incl. bad frames, broadcast frames, and multicast frames received). This object applies only to transceiver ports provisioned for the 10 gigabit ethernet LAN protocol.

OBJECT-TYPE

The date and time stamp of the total received frames count value.

OBJECT-TYPE

Indicates the validity of the provided received frames count value.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMTFRCRXValue object to 0.

OBJECT-TYPE

The total number of good frames received that were directed to the broadcast address. Note that this does not include multicast frames. This object applies only to transceiver ports provisioned for the 10 gigabit ethernet LAN protocol.

OBJECT-TYPE

The date and time stamp of the broadcast packets received count value.

OBJECT-TYPE

Indicates the validity of the provided broadcast packets received count value.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMBCSTValue object to 0.

OBJECT-TYPE

The total number of good frames received that were directed to a multicast address. Note that this number does not include frames directed to the broadcast address. This object applies only to transceiver ports provisioned for the 10 gigabit ethernet LAN protocol.

OBJECT-TYPE

The date and time stamp of the multicast packets received count value.

OBJECT-TYPE

Indicates the validity of the provided multicast packets received count value.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMMCSTValue object to 0.

OBJECT-TYPE

The total number of 64 byte frames received (excluding framing bits but including FCS octets). This object applies only to transceiver ports provisioned for the 10 gigabit ethernet LAN protocol.

OBJECT-TYPE

The date and time stamp of the count of 64-byte packets received.

OBJECT-TYPE

Indicates the validity of the provided count of 64-byte packets packets received.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMSIZE64Value object to 0.

OBJECT-TYPE

The total number of frames received that are 65 to 127 bytes inclusive in length (excluding framing bits but including FCS octets). This object applies only to transceiver ports provisioned for the 10 gigabit ethernet LAN protocol.

OBJECT-TYPE

The date and time stamp of the count of packets between 65 and 127 bytes.

OBJECT-TYPE

Indicates the validity of the provided count of packets between 65 and 127 bytes.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMSIZE65To127Value object to 0.

OBJECT-TYPE

The total number of frames received that are 128 to 255 bytes inclusive in length (excluding framing bits but including FCS octets). This object applies only to transceiver ports provisioned for the 10 gigabit ethernet LAN protocol.

OBJECT-TYPE

The date and time stamp of the count of packets between 128 and 255 bytes.

OBJECT-TYPE

Indicates the validity of the provided count of packets between 128 and 255 bytes.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMSIZE128To255Value object to 0.

OBJECT-TYPE

The total number of frames received that are 256 to 511 bytes inclusive in length (excluding framing bits but including FCS octets). This object applies only to transceiver ports provisioned for the 10 gigabit ethernet LAN protocol.

OBJECT-TYPE

The date and time stamp of the count of packets between 256 and 511 bytes.

OBJECT-TYPE

Indicates the validity of the provided count of packets between 256 and 511 bytes.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMSIZE256To511Value object to 0.

OBJECT-TYPE

The total number of frames received that are 512 to 1023 bytes inclusive in length (excluding framing bits but including FCS octets). This object applies only to transceiver ports provisioned for the 10 gigabit ethernet LAN protocol.

OBJECT-TYPE

The date and time stamp of the count of packets between 512 and 1023 bytes.

OBJECT-TYPE

Indicates the validity of the provided count of packets between 512 and 1023 bytes.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMSIZE512To1023Value object to 0.

OBJECT-TYPE

The total number of frames received that are 1024 to 1518 bytes inclusive in length (excluding framing bits but including FCS octets). This object applies only to transceiver ports provisioned for the 10 gigabit ethernet LAN protocol.

OBJECT-TYPE

The date and time stamp of the count of packets between 1024 and 1518 bytes.

OBJECT-TYPE

Indicates the validity of the provided count of packets between 1024 and 1518 bytes.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMSIZE1024To1518Value object to 0.

OBJECT-TYPE

The total number of frames received that are greater than or equal to 1519 bytes in length (excluding framing bits but including FCS octets). This object applies only to transceiver ports provisioned for the 10 gigabit ethernet LAN protocol.

OBJECT-TYPE

The date and time stamp of the count of packets over 1518 bytes.

OBJECT-TYPE

Indicates the validity of the provided count of packets over 1518 bytes.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMSIZEOver1518Value object to 0.

OBJECT-TYPE

The count of packets that had a valid length but had either a Frame Check Sequence (FCS) or a bad FCS with a non-integral number of octets (Alignment Error) . This object applies only to transceiver ports provisioned for the 10 gigabit ethernet LAN protocol.

OBJECT-TYPE

The date and time stamp of the count of packets with bad FCS or alignment error.

OBJECT-TYPE

Indicates the validity of the provided count of packets with bad FCS or alignment error.

OBJECT-TYPE

The total number of dropped frames due to lack of resources or otherwise. Note that this number is not necessarily the number of frames dropped; it is just the number of times that it could be detected. This object applies only to transceiver ports provisioned for the 10 gigabit ethernet LAN protocol.

OBJECT-TYPE

The date and time stamp of the count of dropped packets.

OBJECT-TYPE

Indicates the validity of the provided count of dropped packets.

OBJECT-TYPE

The total number of frames received that were less than 64 octets long (excluding framing bits, but including FCS octets) and were otherwise well formed. This object applies only to transceiver ports provisioned for the 10 gigabit ethernet LAN protocol.

OBJECT-TYPE

The date and time stamp of the count of undersized packets.

OBJECT-TYPE

Indicates the validity of the provided count of undersized packets.

OBJECT-TYPE

The total number of frames received that were longer than 9600 octets (excluding framing bits, but including FCS octets) and were otherwise well formed. This object applies only to transceiver ports provisioned for the 10 gigabit ethernet LAN protocol.

OBJECT-TYPE

The date and time stamp of the count of oversized packets.

OBJECT-TYPE

Indicates the validity of the provided count of oversized packets.

OBJECT-TYPE

The total number of frames received that were less than 64 octets in length (excluding framing bits but including FCS octets) and had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets (Alignment Error). This object applies only to transceiver ports provisioned for the 10 gigabit ethernet LAN protocol.

OBJECT-TYPE

The date and time stamp of the count of received packet fragments.

OBJECT-TYPE

Indicates the validity of the provided count of received packet fragments.

OBJECT-TYPE

The total number of frames received that were longer than 14336 9600 octets (excluding framing bits, but including FCS octets), and had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with non-integral number of octets (Alignment Error). This object applies only to transceiver ports provisioned for the 10 gigabit ethernet LAN protocol.

OBJECT-TYPE

The date and time stamp of the count of received jabbers.

OBJECT-TYPE

Indicates the validity of the provided count of received jabbers.

OBJECT-TYPE

The count of OTN digital wrapper layer errored blocks.

OBJECT-TYPE

The date and time stamp of the OTN digital wrapper layer errored blocks value.

OBJECT-TYPE

Indicates the validity of the provided OTN digital wrapper layer errored blocks value.

OBJECT-TYPE

The count of OTN digital wrapper layer background block errors.

OBJECT-TYPE

The date and time stamp of the OTN digital wrapper layer background block errors.

OBJECT-TYPE

Indicates the validity of the provided OTN digital wrapper layer background block errors value.

OBJECT-TYPE

The count of errored seconds at the OTN digital wrapper layer.

OBJECT-TYPE

The date and time stamp of the OTN digital wrapper layer errored seconds value.

OBJECT-TYPE

Indicates the validity of the provided OTN digital wrapper layer errored seconds value.

OBJECT-TYPE

The count of severely errored seconds at the OTN digital wrapper layer.

OBJECT-TYPE

The date and time stamp of the OTN digital wrapper layer severely errored seconds value.

OBJECT-TYPE

Indicates the validity of the provided OTN digital wrapper layer severely errored seconds value.

OBJECT-TYPE

The count of Out-Of-Frame seconds at the OTN digital wrapper layer.

OBJECT-TYPE

The date and time stamp of the OTN digital wrapper layer Out-Of-Frame seconds value.

OBJECT-TYPE

Indicates the validity of the provided OTN digital wrapper layer Out-of-Frame seconds value.

OBJECT-TYPE

A second supply voltage value on the transceiver.

OBJECT-TYPE

The date and time stamp of the second supply voltage value.

OBJECT-TYPE

Indicates the validity of the provided second supply voltage value.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMCVSValue object to 0.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMESSValue object to 0.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMSESSValue object to 0.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMSEFSSValue object to 0.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMRSEBValue object to 0.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMRSBBEValue object to 0.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMRSESValue object to 0.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMRSSESValue object to 0.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMRSOFSValue object to 0.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMCVValue object to 0.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMESValue object to 0.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMSESValue object to 0.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMINVBLKValue object to 0.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMNBITCRValue object to 0.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMNBYTCRValue object to 0.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMUNCRCDWValue object to 0.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMFCSEValue object to 0.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMFRDRValue object to 0.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMUSIZEValue object to 0.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMOSIZEValue object to 0.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMFRGTValue object to 0.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMJABRValue object to 0.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMOTUEBValue object to 0.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMOTUBBEValue object to 0.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMOTUESValue object to 0.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMOTUSESValue object to 0.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMOTUOFSValue object to 0.

OBJECT-TYPE

The count of unavailable seconds at the section layer. This object applies only to transciever ports provisioned for a SONET OC-N protocol.

OBJECT-TYPE

The date and time stamp of the section layer unavailable seconds value.

OBJECT-TYPE

Indicates the validity of the provided section layer unavailable seconds value.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMUASSValue object to 0.

OBJECT-TYPE

The count of regenerator section unavailable seconds. This object applies only to transciever ports provisioned for a SDH STM-N protocol.

OBJECT-TYPE

The date and time stamp of the regenerator section unavailable seconds value.

OBJECT-TYPE

Indicates the validity of the provided regenerator section unavailable seconds value.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMRSUASValue object to 0.

OBJECT-TYPE

The count of unavailable seconds. This object applies only to transciever ports provisioned for the gigabit ethernet protocol or a fiber channel protocol.

OBJECT-TYPE

The date and time stamp of the unavailable seconds value.

OBJECT-TYPE

Indicates the validity of the provided unavailable seconds value.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMUASValue object to 0.

OBJECT-TYPE

The count of unavailable seconds at the OTN digital wrapper layer.

OBJECT-TYPE

The date and time stamp of the OTN digital wrapper layer unavailable seconds value.

OBJECT-TYPE

Indicates the validity of the provided OTN digital wrapper layer unavailable seconds value.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMOTUUASValue object to 0.

OBJECT-TYPE

The instantaneous BER of transciever ports provisioned for the 10 gigabit ethernet LAN with FEC protocol.

OBJECT-TYPE

The date and time stamp of the instantaneous BER.

OBJECT-TYPE

Indicates the validity of the provided instantaneous BER.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMOTNBERValue object to 0.

OBJECT-TYPE

The average/interval BER of transciever ports provisioned for the 10 gigabit ethernet LAN with FEC protocol.

OBJECT-TYPE

The date and time stamp of the average/interval BER.

OBJECT-TYPE

Indicates the validity of the provided average/interval BER.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMOTNAVGBERValue object to 0.

OBJECT-TYPE

The 64-bit count of the number of bits corrected. This object applies only to transciever ports provisioned for a protocol that includes Forward Error Correction (FEC).

OBJECT-TYPE

The date and time stamp of the 64-bit number of bits corrected value.

OBJECT-TYPE

Indicates the validity of the provided 64-bit number of bits corrected value.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMNBITCR64BitValue object to 0.

OBJECT-TYPE

The 64-bit count of the number of bytes corrected. This object applies only to transciever ports provisioned for a protocol that includes Forward Error Correction (FEC).

OBJECT-TYPE

The date and time stamp of the 64-bit number of bytes corrected value.

OBJECT-TYPE

Indicates the validity of the provided 64-bit number of bytes corrected value.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMNBYTCR64BitValue object to 0.

OBJECT-TYPE

The minimum optical power received on the input of the transceiver.

OBJECT-TYPE

The date and time stamp of the minimum optical power received value.

OBJECT-TYPE

Indicates the validity of the provided minimum optical power received value.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMOPRMinValue object to 0.

OBJECT-TYPE

The maximum optical power received on the input of the transceiver.

OBJECT-TYPE

The date and time stamp of the maximum optical power received value.

OBJECT-TYPE

Indicates the validity of the provided maximum optical power received value.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMOPRMaxValue object to 0.

OBJECT-TYPE

The average optical power received on the input of the transceiver.

OBJECT-TYPE

The date and time stamp of the average optical power received value.

OBJECT-TYPE

Indicates the validity of the provided average optical power received value.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMOPRAvgValue object to 0.

OBJECT-TYPE

The minimum optical power transmitted at the output of the transceiver.

OBJECT-TYPE

The date and time stamp of the minimum optical power transmitted value.

OBJECT-TYPE

Indicates the validity of the provided minimum optical power transmitted value.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMOPTMinValue object to 0.

OBJECT-TYPE

The maximum optical power transmitted at the output of the transceiver.

OBJECT-TYPE

The date and time stamp of the maximum optical power transmitted value.

OBJECT-TYPE

Indicates the validity of the provided maximum optical power transmitted value.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMOPTMaxValue object to 0.

OBJECT-TYPE

The average optical power transmitted at the output of the transceiver.

OBJECT-TYPE

The date and time stamp of the average optical power transmitted value.

OBJECT-TYPE

Indicates the validity of the provided average optical power transmitted value.

OBJECT-TYPE

Used to initialize the value of the xcvrCrntPMOPTAvgValue object to 0.

OBJECT-TYPE

A table of historical performance monitoring statistics collected for the optical transceiver facilities on the NE.