TIMETRA-MPLS-MIB

TEXTUAL-CONVENTION

TmnxMplsLabelOwner is an enumerated integer that specifies the module that owns a particular MPLS label.

TEXTUAL-CONVENTION

TmnxMplsLspAddrType is an enumerated integer that specifies the address type for an MPLS LSP.

TEXTUAL-CONVENTION

TmnxMplsLspAutoBWLastAdjCause is an enumerated integer that specifies cause of auto-bandwidth last adjustment.

TEXTUAL-CONVENTION

TmnxMplsLspBgpRSVPLSPTunState is an enumerated integer that specifies whether an RSVP LSP is allowed or blocked in its usage as a transport LSP for BGP tunnel routes. In 'include(1)' mode, an RSVP LSPs is allowed to be used as transport LSP for BGP tunnel routes. In 'exclude(2)' mode, an RSVP LSP is not allowed to be used as a transport LSP for BGP tunnel routes.

TEXTUAL-CONVENTION

TmnxMplsLspFailCode is an enumerated integer that defines the reason for LSP Path and LSP Crossconnect failure.

TEXTUAL-CONVENTION

TmnxMplsMBBType is an enumerated integer that specifies the type of make-before-break (MBB).

TEXTUAL-CONVENTION

TmnxMplsOperDownReasonCode is an enumerated integer that specifies the reason that the MPLS instance is operationally down.

TEXTUAL-CONVENTION

TmnxMplsP2mpInstFailCode is an enumerated integer that defines the reason for P2MP instance going down.

TEXTUAL-CONVENTION

The value of TmnxMplsRouterId provides a 32-bit, unsigned integer uniquely identifying the router in the Autonomous System. To ensure uniqueness, this may default to the value of one of the router's IPv4 host addresses if IPv4 is configured on the router.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

The vRtrMplsLspTable has an entry for each Labeled Switch Path (LSP) configured for a virtual router in the system.

OBJECT-TYPE

Each row entry represents a Labeled Switch Path (LSP) configured for a virtual router in the system. Entries can be created and deleted via SNMP SET operations. Setting RowStatus to 'active' requires vRtrMplsLspName to have been assigned a valid value.

OBJECT-TYPE

The value of vRtrMplsLspIndex specifies the Labeled Switch Path (LSP) index for this virtual router in the Nokia SROS system. It is a unique value among entries with the same value of vRtrID.

OBJECT-TYPE

The row status used for creation, deletion, or control of vRtrMplsLspTable entries. Before the row can be placed into the 'active' state vRtrMplsLspName must have been assigned a valid value.

OBJECT-TYPE

The sysUpTime when this row was last modified.

OBJECT-TYPE

Administrative name for this Labeled Switch Path. The vRtrMplsLspName must be unique within a virtual router instance. When the value of the object vRtrMplsLspType is 'p2mpAuto', LSPs are auto-created dynamically by the system using LSP template values configured in the associated row entry of vRtrMplsLspTemplateTable. For auto-created LSPs, vRtrMplsLspName can have a maximum of 64 characters which consists of vRtrMplsLspTemplateName, vRtrID and MTTM(Multicast Tunnel Table Manager)Identifier. If vRtrMplsLspType is not 'p2mpAuto', 'meshP2p' or 'oneHopP2p', vRtrMplsLspName can have a maximum of 32 characters.

OBJECT-TYPE

The desired administrative state for this LSP.

OBJECT-TYPE

The current operational state of this LSP.

OBJECT-TYPE

The vRtrMplsLspFromAddr specifies the source address of this LSP. When vRtrMplsLspFromAddrType is 'ipv4', vRtrMplsLspFromAddr should also be specified. If vRtrMplsLspFromAddr has not been explicitly set, the system IP address will be used. vRtrMplsLspFromAddr is obsoleted in 20.0, replaced by vRtrMplsLspNgFromAddr

OBJECT-TYPE

The vRtrMplsLspToAddr specifies the destination address of this LSP. When vRtrMplsLspToAddrType is 'ipv4', vRtrMplsLspToAddr should also be specified. When vRtrMplsLspToAddrType is 'ipv6', vRtrMplsLspNgToAddr should also be specified. vRtrMplsLspToAddr is obsoleted in 20.0, replaced by vRtrMplsLspNgToAddr

OBJECT-TYPE

The value of object vRtrMplsLspType specifies whether the label value is statically or dynamically assigned or whether the LSP will be used exclusively for bypass protection. The value 'p2mpLsp' will be used to indicate point to multipoint LSPs used for multicast traffic. When the value of the vRtrMplsLspType is 'p2mpAuto', it specifies that the LSP is auto-created dynamically by the system and the row entry is dynamically created by the system using LSP Template values configured in the associated row entry of vRtrMplsLspTemplateTable. The value 'mplsTp' specifies that the LSP is an MPLS-TP Static LSP. When the value of the vRtrMplsLspType is 'meshP2p', it specifies that the LSP is a mesh point-to-point created dynamically by the system and the row entry is dynamically created by the system using Mesh LSP Template values configured in the associated row entry of vRtrMplsLspTemplateTable. When the value of the vRtrMplsLspType is 'oneHopP2p', it specifies that the LSP is a one-hop point-to-point LSP created dynamically by the system and the row entry is dynamically created by the system using One-Hop LSP Template values configured in the associated row entry of vRtrMplsLspTemplateTable. When the value of vRtrMplsLspType is set to 'segmentRouting', it specifies that the LSP is used for segment routing and vRtrMplsLspType can only be set to 'segmentRouting' when the value of vRtrMplsLspIndex is greater than 65535. A 'wrongValue' error is returned if an attempt is made to set an object in the row entry where the value of vRtrMplsLspType is 'p2mpAuto'. When value of the vRtrMplsLspType is 'meshP2pSrTe', it specifies that the segment routing LSP is a mesh point-to-point created dynamically by the system and the row entry is dynamically created by the system using meshP2PSrTe LSP Template values configured in the associated row entry of vRtrMplsLspTemplateTable. When the value of the vRtrMplsLspType is 'oneHopP2pSrTe', it specifies that the LSP is a one-hop point-to-point segment routing LSP created dynamically by the system and the row entry is dynamically created by the system using onehopP2PSrTe LSP Template values configured in the associated row entry of vRtrMplsLspTemplateTable. When value of the vRtrMplsLspType is 'pceInitP2pSrTe', it specifies that the point-to-point segment routing LSP is created dynamically on receiving a PCE-Initiated Message from PCC, using pceInitP2pSrTe LSP Template values configured in the associated row entry of vRtrMplsLspTemplateTable.

OBJECT-TYPE

The vRtrMplsLspOutSegIndx is the index value of the entry in the mplsOutSegmentTable associated with this vRtrMplsLspEntry when vRtrMplsLspType is 'static'. If vRtrMplsLspType is 'dynamic', the value of this object will be zero (0).

OBJECT-TYPE

The value of vRtrMplsLspRetryTimer specifies the time in seconds the software will wait before attempting the establish the failed LSP.

OBJECT-TYPE

The value of vRtrMplsLspRetryLimit specifies the number of attempts the software should make to reestablish a failed LSP before the LSP is disabled. A value of 0 indicates that an infinite number of retry attempts should be made.

OBJECT-TYPE

The value of vRtrMplsLspMetric specifies the metric for this LSP which is used to select an LSP among a set of LSPs which are destined to the same egress 7x50 router. The LSP with the lowest metric will be selected. In LDP-over-RSVP, LDP performs a lookup in the Routing Table Manager (RTM) which provides the next hop to the destination PE and the advertising router (ABR or destination PE itself). If the advertising router matches the targeted LDP peer, LDP then performs a second lookup for the advertising router in the Tunnel Table Manager (TTM). This lookup returns the best RSVP LSP to use to forward packets for an LDP FEC learned through the targeted LDP session. The lookup returns the LSP with the lowest metric. If multiple LSPs have the same metric, then the result of the lookup will be to select the first one available in the TTM. A value of '0' indicates metric is not to be used.

OBJECT-TYPE

When the value of vRtrMplsLspDecrementTtl is 'true', the ingress ESR writes the TTL of the IP packet into the label and each transit ESR decrements the TTL in the label. At the egress ESR the TTL value from the label is written into the IP packet. When the value of vRtrMplsLspDecrementTtl is 'false', the ingress ESR ignores the IP packet TTL and writes the value of 255 into the label; and the egress ESR does not write the label's TTL into the IP packet. This object was made obsolete in release 11.0.

OBJECT-TYPE

When the value of vRtrMplsLspCspf is 'true', CSPF computation for constrained-path LSP is enabled. When the value of vRtrMplsLspCspf is 'false' CSPF computation is disabled.

OBJECT-TYPE

When the value of vRtrMplsLspFastReroute is 'true', fast reroute is enabled. A pre-computed detour LSP is created from each node in the primary path of this LSP. In case of a failure of a link or LSP between two nodes, traffic is immediately rerouted on the pre-computed detour LSP thus avoiding packet loss. Each node along the primary path of the LSP tries to establish a detour LSP as follows: Each upstream node will setup a detour LSP that avoids only the immediate downstream node and merges back onto the actual path of the LSP as soon as possible. The detour LSP may take one or more hops (up to the value of vRtrMplsLspFRHopLimit) before merging back onto the main LSP path. When the upstream node detects a downstream link or node failure, it immediately send traffic for that LSP on the detour path and at the same time signals back to the ingress ESR about the failure. Fast reroute applies only to the primary path of this LSP. No configuration is required on the transit hops of the LSP. The ingress ESR will signal all intermediate ESRs using RSVP to setup their detours. When the value of vRtrMplsLspFastReroute is 'false', fast rerouting is disabled.

OBJECT-TYPE

The value of vRtrMplsLspFRHopLimit specifies the total number of hops a detour LSP can take before merging back onto the main LSP path.

OBJECT-TYPE

The value of vRtrMplsLspFRBandwidth specified the amount of bandwidth in megabits per second (Mbps) to be reserved for the detour LSP. A value of zero (0) indicates that no bandwidth is reserved.

OBJECT-TYPE

The name of the class of service value to be assigned to all packets on the LSP is specified with vRtrMplsLspClassOfService. The EXP bits in the MPLS header are set based on the global mapping table that specified the mapping between the forwarding class and the EXP bits. When class of service is specified, all packets will be marked with the same EXP bits that match the vRtrMplsLspClassOfService name in the mapping table. An empty string, ''H, specifies no class of service. Packets are assigned EXP bits based on the same mapping table, however each packet is marked with EXP bits based on the forwarding class from which it is serviced. When the value of vRtrMplsLspPathCosSource is set to 'inherit', the value of vRtrMplsLspClassOfService is applied to that specific LSP/path. This object was made obsolete in release 11.0.

OBJECT-TYPE

The value of vRtrMplsLspSetupPriority specifies the setup priority to use when insufficient bandwidth is available to setup a LSP. The setup priority is compared against the hold priority of existing LSPs. If the setup priority is higher than the hold priority of the established LSPs, this LSP may preempt the other LSPs. A value of zero (0) is the highest priority and a value of seven (7) is the lowest priority. When the value of vRtrMplsLspPathSetupPriority is set to '-1', the value of vRtrMplsLspSetupPriority is applied to that specific LSP/path.

OBJECT-TYPE

The value of vRtrMplsLspHoldPriority specifies the hold priority to use when insufficient bandwidth is available to setup a LSP. The setup priority is compared against the hold priority of existing LSPs. If the setup priority is higher than the hold priority of the established LSPs, this LSP may preempt the other LSPs. A value of zero (0) is the highest priority and a value of seven (7) is the lowest priority. When the value of vRtrMplsLspPathHoldPriority is set to '-1', the value of vRtrMplsLspHoldPriority is applied to that specific LSP/path.

OBJECT-TYPE

When the value of vRtrMplsLspRecord is 'true', recording of all the hops that a LSP traverses is enabled. When the value of vRtrMplsLspRecord is 'false, recording of all the hops that a LSP traverses is disabled.

OBJECT-TYPE

The value of vRtrMplsLspPreference specifies the preference for the LSP. This value is used for load balancing between multiple LSPs that exist between the same ingress and egress routers. By default, traffic is load balanced among the LSPs, since all LSPs have the same preference. To prefer one LSP over another, change the preference value for that LSP. The LSP with the lowest preference is used. This object was made obsolete in release 11.0.

OBJECT-TYPE

The value of vRtrMplsLspBandwidth specifies the amount of bandwidth in megabits per second (Mbps) to be reserved for the LSP. A value of zero (0) indicates that no bandwidth is reserved. When vRtrMplsLspPathBandwidth is set to -1, the value of vRtrMplsLspBandwidth is applied to that specific LSP/path.

OBJECT-TYPE

When vRtrMplsLspBwProtect has a value of 'true', bandwidth protection is enabled on a LSP. LSPs that reserve bandwidth will be used for EF services where customers need guaranteed bandwidth. It is expected that multiple EF services will be assigned to a single LSP. When bandwidth protection is enabled on an LSP, each time this LSP is used for a certain service the bandwidth allocated on that service is deducted from the bandwidth reserved for the LSP. Once the bandwidth is exhausted on the LSP, the ESR will provide feedback to the provider indicating that this LSP has exhausted its resources. This object was made obsolete in release 11.0.

OBJECT-TYPE

The value of vRtrMplsLspHopLimit specifies the maximum number of hops that a LSP will traverse including the ingress and egress ESRs. A LSP will not be setup if the hop limit is exceeded. When the value of vRtrMplsLspPathHopLimit is set to zero (0), the value of vRtrMplsLspHopLimit is applied to that specific LSP/path.

OBJECT-TYPE

The value of vRtrMplsLspNegotiatedMTU specifies the size for the Maximum transmission unit (MTU) that is negotiated during LSP establishment.

OBJECT-TYPE

The value of vRtrMplsLspRsvpResvStyle specifies the reservation style for RSVP. The reservation style can be set to 'Shared- Explicit' (se) or 'Fixed-Filter' (ff).

OBJECT-TYPE

When the value of vRtrMplsLspRsvpAdspec is 'true', the ADSPEC object will be included in RSVP messages. When the value of vRtrMplsLspRsvpAdspec is 'false', the ADSPEC object will not be included in RSVP messages.

OBJECT-TYPE

The value of vRtrMplsLspFRMethod specifies the fast reroute method used. In the 'One-to-one Backup' method, a backup LSP is established which will intersect the original LSP somewhere downstream of the point of link or node failure. For each LSP that is backed up, a separate backup LSP is established. In the 'Facility Backup' method, instead of creating a separate LSP for every LSP that is to be backed up, a single LSP is created which serves as a backup for a set of LSPs. Such an LSP tunnel is called a 'bypass tunnel'.

OBJECT-TYPE

Setting the value of vRtrMplsLspFRNodeProtect to 'true' enables node protection i.e. protection against the failure of a node on the LSP. Setting the value to 'false' disables node protection.

OBJECT-TYPE

The value of vRtrMplsLspAdminGroupInclude is a bit-map that specifies a list of admin groups that should be included when this LSP is setup. If bit 'n' is set, then the admin group with value 'n' is included for this LSP. This implies that each link that this LSP goes through must be associated with at least one of the admin groups in the include list. By default, all admin groups are in the include list.

OBJECT-TYPE

The value of vRtrMplsLspAdminGroupExclude is a bit-map that specifies a list of admin groups that should be excluded when this LSP is setup. If bit 'n' is set, then the admin group with value 'n' is excluded for this LSP. This implies that each link that this LSP goes through must not be associated with any of the admin groups in the exclude list. By default, no admin groups are in the exclude list.

OBJECT-TYPE

Setting the value of vRtrMplsLspAdaptive to 'true' enables make-before-break functionality for the LSP. When the attributes of an already established LSP are changed, either through manual configuration or due to a change in network topology, make-before-break functionality ensures that the resources of the existing LSP will not be released until a new path (with the same LSP Id) has been established and traffic flowing over the existing path is seamlessly transferred to the new path. Setting the value to 'false' disables make-before-break functionality.

OBJECT-TYPE

For each writable object in this row that can be configured to inherit its value from the corresponding object in the vRtrMplsGeneralTable, there is bit within vRtrMplsLspInheritance that controls whether to inherit the operational value of the object or use the administratively set value. Non mask bits will always have value of zero. This object is a bit-mask, with the following positions: vRtrMplsLspOptimizeTimer 0x1 vRtrMplsLspFRObject 0x2 vRtrMplsLspHoldTimer 0x4 vRtrMplsLspDestGlobalId 0x8 When the bit for an object is set to one, then the object's administrative and operational value are whatever the DEFVAL or most recently SET value is. When the bit for an object is set to zero, then the object's administrative and operational value are inherited from the corresponding object in vRtrMplsGeneralTable or vRtrMplsTpSystemTable.

OBJECT-TYPE

The value of vRtrMplsLspOptimizeTimer specifies the time, in seconds, the software will wait before attempting to re-optimize the LSP. When CSPF is enabled, changes in the network topology may cause the existing path of a loose-hop LSP to become sub-optimal. Such LSPs can be re-optimized and rerouted through more optimal paths by recalculating the path for the LSP at periodic intervals. This interval is controlled by the optimize timer. A value of 0 indicates that optimization has been disabled. When the vRtrMplsLspOptimizeTimer bit in vRtrMplsLspInheritance is cleared (0), the value returned in the GET request is inherited from vRtrMplsGeneralOptimizeTimer.

OBJECT-TYPE

The value of vRtrMplsLspOperFastReroute indicates whether the operational LSP has fast reroute enabled or disabled. When make-before-break functionality for the LSP is enabled and if the fast reroute setting is changed, the resources for the existing LSP will not be released until a new path with the new attribute settings has been established. While a new path is being signaled, the administrative value and the operational values of fast reroute setting for the LSP may differ. The value of vRtrMplsLspFastReroute specifies the setting used for the new LSP path trying to be established whereas the value of vRtrMplsLspOperFastReroute specifies the setting for the existing LSP path.

OBJECT-TYPE

The value of vRtrMplsLspFRObject specifies whether fast reroute, for LSPs using 'Facility Backup', is signalled with or without the fast reroute object. The value of vRtrMplsLspFRObject is ignored if fast reroute is disabled for the LSP or if the LSP is using 'One-to-one Backup'. When the vRtrMplsLspFRObject bit in vRtrMplsLspInheritance is cleared (0), the value returned in the GET request is inherited from vRtrMplsGeneralFRObject.

OBJECT-TYPE

The value of vRtrMplsLspHoldTimer specifies the time, in seconds, for which the ingress node holds a bit before programming its data plane and declaring the lsp up to the service module. The value of vRtrMplsLspHoldTimer is inherited from the value of vRtrMplsGeneralHoldTimer.

OBJECT-TYPE

The value of vRtrMplsLspCspfTeMetricEnabled specifies whether the TE metric would be used for the purpose of the LSP path computation by CSPF. When the value of this object is 'false', the IGP metric is used to compute the path of the LSP by CSPF.

OBJECT-TYPE

The value of vRtrMplsLspP2mpId specifies a unique identifier known as point to multipoint (P2MP) identifier (ID).

OBJECT-TYPE

The value of vRtrMplsLspClassType specifies the class type (CT) associated with this LSP.

OBJECT-TYPE

The value of vRtrMplsLspOperMetric indicates the operational metric for the LSP.

OBJECT-TYPE

The value of vRtrMplsLspLdpOverRsvpInclude specifies that this LSP can be included by IGP to calculate its SPF tree. The IGP (OSPF or ISIS) will subsequently provide LDP with all ECMP IGP next-hops and tunnel endpoints that it considers to be the lowest cost path to the destination. If an IGP calculation and an LDP over RSVP produce the same cost then LDP will always prefer an LDP over RSVP tunnel over an IGP route. By default, static and dynamic LSPs will be included when they are created. The default value for p2mp and bypass-only LSPs will be 'false'.

OBJECT-TYPE

The value of vRtrMplsLspLeastFill specifies whether the use of the least-fill path selection method for the computation of the path of this LSP is enabled. By default, the path of an LSP is randomly chosen among a set of equal cost paths.

OBJECT-TYPE

The value of vRtrMplsLspVprnAutoBindInclude specifies whether the LSP can be used as part of the auto-bind feature for VPRN services. By default a LSP is available for inclusion to be used for the auto-bind feature. By default, static and dynamic LSPs will be included when they are created. The default value for p2mp and bypass-only LSPs will be 'false'.

OBJECT-TYPE

The value of vRtrMplsLspMainCTRetryLimit specifies the number of attempts the software should make before it can start using the backup class type.

OBJECT-TYPE

The value of vRtrMplsLspIgpShortcut specifies whether to exclude or include a RSVP LSP from being used as a shortcut while resolving IGP routes. When the value of vRtrMplsLspIgpShortcut is set to 'true' the RSVP LSP is used as a shortcut while resolving IGP routes. When the value of vRtrMplsLspIgpShortcut is set to 'false' the RSVP LSP is not used as a shortcut while resolving IGP routes. When the value of vRtrMplsLspIgpShortcut is changed, the value of vRtrMplsLspIgpShortcutLfaType is reset to its default value.

OBJECT-TYPE

When the value of the vRtrMplsLspType is 'p2mpAuto', the value of vRtrMplsLspOriginTemplate indicates the LSP Template which was used to create this LSP. For all other types of LSPs, the value of vRtrMplsLspOriginTemplate is an empty string.

OBJECT-TYPE

The value of the vRtrMplsLspAutoBandwidth specifies whether automatic bandwidth adjustment has been enabled or disabled for this LSP. A value of 'true' specifies that automatic bandwidth adjustment has been enabled for this LSP and a value of 'false' specifies that automatic bandwidth adjustment has been disabled for this LSP.

OBJECT-TYPE

The value of the vRtrMplsLspCspfToFirstLoose specifies whether the CSPF calculation till the first loose hop on ingress Label Edge Router (LER) is enabled or disabled for this Labeled Switched Path(LSP). By default, the value of vRtrMplsLspCspfToFirstLoose is 'false' which specifies that the CSPF calculation is done to the destination of LSP. This object was deprecated in the 11.0 release.

OBJECT-TYPE

The value of the vRtrMplsLspPropAdminGroup specifies whether the propagation of session attribute object with resource affinity (C-type 1) in PATH message is enabled. By default, the value of vRtrMplsLspPropAdminGroup is 'false' which specifies the session attribute object without resource affinity (C-Type 7) is propagated in PATH message and the admin groups are ignored on Label Switched Router(LSR) while doing CSPF calculation.

OBJECT-TYPE

The value of vRtrMplsLspBgpShortcut specifies whether to exclude or include a RSVP LSP from being used as a shortcut while resolving BGP routes. When the value of vRtrMplsLspBgpShortcut is set to 'true' the RSVP LSP is used as a shortcut while resolving BGP routes. When the value of vRtrMplsLspBgpShortcut is set to 'false' the RSVP LSP is not used as a shortcut while resolving BGP routes.

OBJECT-TYPE

The value of vRtrMplsLspBgpTransportTunnel specifies whether an RSVP LSP is allowed or blocked in its usage as a transport LSP for BGP tunnel routes. When the value of vRtrMplsLspBgpTransportTunnel is set to 'include' an RSVP LSP is allowed to be used as a transport LSP for BGP tunnel routes. When the value of vRtrMplsLspBgpTransportTunnel is set to 'exclude' an RSVP LSP is not allowed to be used as a transport LSP for BGP tunnel routes.

OBJECT-TYPE

The value of vRtrMplsLspSwitchStbyPath specifies whether to trigger the switch from the current active standby LSP path to a new LSP path as specified by vRtrMplsLspSwitchStbyPathIndex. When SET to the value of 'doAction', if the LSP path is actively on a current standby path, signaling will be initiated to switch to the new path. If a signal is triggered while a resignaling is already in progress, the old transient state will be destroyed and a new transaction will be triggered. This variable must be set along with vRtrMplsLspSwitchStbyPathIndex to indicate the specific path index to switch to. An SNMP GET request on this object should return 'notApplicable'.

OBJECT-TYPE

The value of vRtrMplsLspSwitchStbyPathIndex specifies the index for the new standby LSP path in mplsTunnelTable. vRtrMplsLspSwitchStbyPath must also be set to 'doAction' for the new standby LSP path to be selected. A value of 0 specifies that the best active path will be selected.

OBJECT-TYPE

The value of vRtrMplsLspSwitchStbyPathForce specifies whether to force a switch from an active LSP path to a new standby path as specified by the values of vRtrMplsLspSwitchStbyPathIndex and vRtrMplsLspSwitchStbyPath. When vRtrMplsLspSwitchStbyPathForce variable is specified vRtrMplsLspSwitchStbyPathIndex and vRtrMplsLspSwitchStbyPath must be also be specified. A value of 'true' for vRtrMplsLspSwitchStbyPathForce specifies a forced switch. A value of 'false' specifies no forced switch.

OBJECT-TYPE

The value of vRtrMplsLspExcludeNodeAddrType specifies the type of vRtrMplsLspExcludeNodeAddr.

OBJECT-TYPE

When vRtrMplsLspExcludeNodeAddr is set to non-zero value, XRO (Exclude Routers) object will be included in bypass path message with supplied IP address. SET the value to 0.0.0.0 to disable.

OBJECT-TYPE

The value of vRtrMplsLspIgpShortcutLfaType specifies whether to exclude or include a RSVP LSP from being used as a shortcut while resolving IGP routes in LFA SPF or whether to exclude or include a RSVP LSP from being used as a LFA SPF. When the value of vRtrMplsLspIgpShortcutLfaType is set to 'lfaProtect' the RSVP LSP is used as a shortcut while resolving IGP routes in LFA SPF as well. When the value of vRtrMplsLspIgpShortcutLfaType is set to 'lfaOnly' the RSVP LSP is used as a LFA SPF and not used as igp shortcut in regular SPF. An 'inconsistentValue' error is returned if an attempt is made to set this object to a non-default value when the value of the object vRtrMplsLspIgpShortcut is not set to 'true'.

OBJECT-TYPE

The vRtrMplsLspToAddrType object is an enumerated value that specifies the destination address type of the LSP. The value of 'ipv4' specifies an IPv4 address and vRtrMplsLspToAddr should be configured. The value of 'nodeId' specifies an MPLS-TP node id and vRtrMplsLspToNodeId should be configured.

OBJECT-TYPE

The vRtrMplsLspFromAddrType object is an enumerated value that specifies the source address type of the LSP. When the value of vRtrMplsLspFromAddrType is 'ipv4', it specifies an IPv4 address type and vRtrMplsLspFromAddr should be configured. When the value of vRtrMplsLspFromAddrType is 'ipv6', it specifies an IPv6 address type and vRtrMplsLspNgFromAddr should be configured. When the value of vRtrMplsLspFromAddrType is 'nodeId', it specifies an MPLS-TP node id type.

OBJECT-TYPE

The value of vRtrMplsLspToNodeId specifies the destination node id of an MPLS-TP Static LSP. vRtrMplsLspToNodeId is configured when vRtrMplsLspToAddrType is set to 'nodeId'.

OBJECT-TYPE

The value of vRtrMplsLspFromNodeId indicates the source node id of an MPLS-TP Static LSP.

OBJECT-TYPE

The value of vRtrMplsLspDestGlobalId specifies the destination global identifier for an MPLS-TP Static LSP. When the vRtrMplsLspDestGlobalId bit in vRtrMplsLspInheritance is cleared (0), the administrative and operational value for destination global identifier is inherited from vRtrMplsTpGlobalId in the vRtrMplsTpSystemTable.

OBJECT-TYPE

The value of vRtrMplsLspDestTunnelNum specifies the destination tunnel number of an MPLS-TP Static LSP. A value of 0 indicates that vRtrMplsLspIndex is to be used as the destination tunnel number.

OBJECT-TYPE

The value of vRtrMplsLspFRPropAdminGroup specifies whether or not the use of administrative group constraints on a FRR backup LSP is enabled. If vRtrMplsLspFastReroute is set to 'true', the value of vRtrMplsLspFRPropAdminGroup specifies whether or not the administrative group constraints are signaled in the vRtrMplsLspFastReroute object. If vRtrMplsLspFastReroute is set to 'false', the value of vRtrMplsLspFRPropAdminGroup is ignored.

OBJECT-TYPE

The value of vRtrMplsLspIgpShortcutRelOffset specifies the the relative offset to the IGP metric on the SPF tree. The SPF tree is updated with the current IGP metric of the path between the endpoints of the LSP minus the value of vRtrMplsLspIgpShortcutRelOffset. The default value of 2147483647 indicates the relative metric offset is not to be considered.

OBJECT-TYPE

The value of vRtrMplsLspRevertTimer specifies a revert timer for a Labeled Switch Path (LSP). When the value of vRtrMplsLspRevertTimer is set to '0', it cancels any revert timer that is currently running and causes the Labeled Switch Path (LSP) to revert to the primary path immediately if it is up. When the value of vRtrMplsLspRevertTimer is set to any non-zero value of revert interval, the Labeled Switch Path (LSP) will be switched to the primary path only after the revert interval is over.

OBJECT-TYPE

The value of vRtrMplsLspRevertTimeRemain indicates the time remaining in minutes before the revert timer would expire causing an lsp revert to primary path.

OBJECT-TYPE

The value of vRtrMplsLspLoadBalancingWeight specifies the load balancing weight applied to this Labeled Switch Path(LSP). When a system level load-balancing command is enabled, packets forwarded to a set of ECMP tunnel next-hops will be sprayed using this weight configured for this LSP.

OBJECT-TYPE

The value of vRtrMplsLspClassFwdingEnabled specifies whether class based forwarding over this MPLS LSP is enabled or not.

OBJECT-TYPE

The value of vRtrMplsLspFC specifies a set of forwarding classes configured for this LSP expressed as a bit map. If a bit from 0 through 7 is set, then the corresponding forwarding class has been configured for this LSP. If bit 8 is set, the LSP has been designated as the default forwarding LSP.

OBJECT-TYPE

The value of vRtrMplsLspBfdTemplateName specifies the TIMETRA-BFD-MIB::tmnxBfdAdminTemplateName used by this LSP.

OBJECT-TYPE

The value of vRtrMplsLspBfdEnable specifies whether BFD is enabled or not for this LSP.

OBJECT-TYPE

The value of vRtrMplsLspBfdPingIntvl specifies the time interval for periodic LSP ping for BFD bootstrapping. The object vRtrMplsLspBfdPingIntvl is applicable to LSPs with vRtrMplsLspType set to 'dynamic'. When the value of vRtrMplsLspBfdPingIntvl is set to '0', it disables LSP pings for BFD bootstrapping.

OBJECT-TYPE

The value of vRtrMplsLspNgFromAddr specifices the source address of this LSP.

OBJECT-TYPE

The value of vRtrMplsLspNgToAddr specifices the destination address of this LSP.

OBJECT-TYPE

The vRtrMplsLspStatTable has an entry for each Labeled Switch Path (LSP) configured for a virtual router in the system.

OBJECT-TYPE

Each row entry represents a collection of statistics for a Labeled Switch Path (LSP) configured for a virtual router in the system. Entries cannot be created and deleted via SNMP SET operations.

OBJECT-TYPE

The number of octets that have been forwarded over current LSP active path. The number reported is not realtime, may be subject to several minutes delay. The delay is controllable by MPLS statistics gathering interval, which by default is once every 5 minutes. If MPLS statistics gathering is not enabled, this number will not increment.

OBJECT-TYPE

The number of packets that have been forwarded over current LSP active path. The number reported is not realtime, may be subject to several minutes delay. The delay is controllable by MPLS statistics gathering interval, which by default is once every 5 minutes. If MPLS statistics gathering is not enabled, this number will not increment.

OBJECT-TYPE

The age (i.e., time from creation till now) of this LSP in 10-millisecond periods.

OBJECT-TYPE

The total time in 10-millisecond units that this LSP has been been operational. For example, the percentage up time can be determined by computing (vRtrMplsLspTimeUp/vRtrMplsLspAge * 100 %).

OBJECT-TYPE

The total time in 10-millisecond units that this LSP has not been operational.

OBJECT-TYPE

The total time in 10-millisecond units that this LSP's primary path has been operational. For example, the percentage contribution of the primary path to the operational time is given by (vRtrMplsLspPrimaryTimeUp/vRtrMplsLspTimeUp * 100) %.

OBJECT-TYPE

The number of state transitions (up -> down and down -> up) this LSP has undergone.

OBJECT-TYPE

The time in 10-millisecond units since the last transition occurred on this LSP.

OBJECT-TYPE

The number of path changes this LSP has had. For every path change (path down, path up, path change), a corresponding syslog/trap (if enabled) is generated for it.

OBJECT-TYPE

The time in 10-millisecond units since the last change occurred on this LSP.

OBJECT-TYPE

The number of paths configured for this LSP.

OBJECT-TYPE

The number of standby paths configured for this LSP.

OBJECT-TYPE

The number of operational paths for this LSP. This includes the path currently active, as well as operational standby paths.

OBJECT-TYPE

The value of vRtrMplsLspConfP2mpInstances indicates the number of p2mp instances configured for this LSP.

OBJECT-TYPE

The value of vRtrMplsLspStatsEgrIndexUnAvail indicates whether an MPLS LSP egress statistics index is available or not for the egress statistics.

OBJECT-TYPE

The value of vRtrMplsLspSelfPingTimeouts indicate the number of times self-ping has timed out for paths in this LSP.

OBJECT-TYPE

voluntary serialization control for vRtrMplsLspPathTable. Primarily used by SNMP manager to coordinate changes to vRtrMplsLspPathInheritance.

OBJECT-TYPE

The vRtrMplsLspPathTable provides an association between an LSP and a path. An LSP can have more than one path association, but only one of those paths can be specified as the primary path type. Paths are defined in as Tunnel entries in the mplsTunnelTable in the MPLS-TE-MIB.

OBJECT-TYPE

Each row entry represents an association between a Labeled Switch Path (LSP) in the vRtrMplsLspTable and a path (or tunnel) entry in the mplsTunnelTable. Entries in this table can be created and deleted via SNMP SET operations. Setting RowStatus to 'active' requires vRtrMplsLspPathType to have been assigned a valid value.

OBJECT-TYPE

The row status used for creation, deletion, or control of vRtrMplsLspPathTable entries. Before the row can be placed into the 'active' state vRtrMplsLspPathType must have been assigned a valid value.

OBJECT-TYPE

The sysUpTime when this row was last modified.

OBJECT-TYPE

This variable is an enum that represents the role this path is taking within this LSP.

OBJECT-TYPE

The configured Class Of Service (COS) for this path. If the value is between 0 and 7 inclusive, this value will be inserted in the 3 bit COS field in the label. If the value is 255, the value in the COS field of the label will depend on other factors. This object was made obsolete in release 11.0.

OBJECT-TYPE

The set of configured properties for this path expressed as a bit map. For example, if the path is an adaptive path, the bit corresponding to bit value 1 is set.

OBJECT-TYPE

The value of vRtrMplsLspPathBandwidth specifies the amount of bandwidth in megabits per seconds (Mbps) to be reserved for this LSP path. A value of zero (0) indicates that no bandwidth is reserved.

OBJECT-TYPE

When vRtrMplsLspPathBwProtect has a value of 'true', bandwidth protection is enabled on a LSP. LSPs that reserve bandwidth will be used for EF services where customers need guaranteed bandwidth. It is expected that multiple EF services will be assigned to a single LSP. When bandwidth protection is enabled on an LSP, each time this LSP is used for a certain service the bandwidth allocated on that service is deducted from the bandwidth reserved for the LSP. Once the bandwidth is exhausted on the LSP, the ESR will provide feedback to the provider indicating that this LSP has exhausted its resources. This object was made obsolete in release 11.0.

OBJECT-TYPE

The current working state of this path within this LSP.

OBJECT-TYPE

When there is no path in the LSP with vRtrMplsLspPathType value of 'primary', 'secondary' type paths of this LSP with the same value of vRtrMplsLspPathPreference are used for load sharing. When a 'primary' type path exists in the LSP, vRtrMplsLspPathPreference is used to denote at which priority one 'secondary' path will supersede another when the 'primary' fails. 1 indicates the highest priority value. For LSP with vRtrMplsLspPathType value of 'standby' type paths the value of vRtrMplsLspPathPreference is in the range of (1..255). For path type 'primary' the value of vRtrMplsLspPathPreference is set to 0. For path type 'secondary' the value of vRtrMplsLspPathPreference is set to 255.

OBJECT-TYPE

When vRtrMplsLspPathCosSource is set to 'true', the value of vRtrMplsLspPathClassOfService overrides vRtrMplsLspClassOfService. When 'false', the value of vRtrMplsLspClassOfService is used. This object was made obsolete in release 11.0.

OBJECT-TYPE

The name of the class of service value to be assigned to all packets on the LSP is specified with vRtrMplsLspPathClassOfService. The EXP bits in the MPLS header are set based on the global mapping table that specified the mapping between the forwarding class and the EXP bits. When class of service is specified, all packets will be marked with the same EXP bits that match the vRtrMplsLspPathClassOfService name in the mapping table. An empty string, ''H, specifies no class of service. Packets are assigned EXP bits based on the same mapping table, however each packet is marked with EXP bits based on the forwarding class from which it is serviced. This object was made obsolete in release 11.0.

OBJECT-TYPE

The value of vRtrMplsLspPathSetupPriority specifies the setup priority to use when insufficient bandwidth is available to setup a LSP. The setup priority is compared against the hold priority of existing LSPs. If the setup priority is higher than the hold priority of the established LSPs, this LSP may preempt the other LSPs. A value of zero (0) is the highest priority and a value of seven (7) is the lowest priority.

OBJECT-TYPE

The value of vRtrMplsLspPathHoldPriority specifies the hold priority to use when insufficient bandwidth is available to setup a LSP. The setup priority is compared against the hold priority of existing LSPs. If the setup priority is higher than the hold priority of the established LSPs, this LSP may preempt the other LSPs. A value of zero (0) is the highest priority and a value of seven (7) is the lowest priority.

OBJECT-TYPE

When the value of vRtrMplsLspPathRecord is 'record', recording of all the hops that a LSP traverses is enabled. When the value of vRtrMplsLspPathRecord is 'noRecord', recording of all the hops that a LSP traverses is disabled.

OBJECT-TYPE

The value of vRtrMplsLspPathHopLimit specifies the maximum number of hops that a LSP will traverse including the ingress and egress ESRs. A LSP will not be setup if the hop limit is exceeded. When the vRtrMplsLspPathHopLimit bit in vRtrMplsLspPathInheritance is cleared (0), the value returned to a GET request is inherited from vRtrMplsLspHopLimit.

OBJECT-TYPE

When vRtrMplsLspPathSharing has a value of 'true', path-sharing is enabled for the secondary path. Path-sharing is used to control the hops of the secondary path. When vRtrMplsLspPathSharing have a value of 'false', CSPF attempts to find a path for the secondary that does not include any node or link that is common to the active primary path. This variable is valid only if vRtrMplsLspPathType is set to 'secondary'. This object was made obsolete in release 11.0.

OBJECT-TYPE

The desired administrative state for this LSP path.

OBJECT-TYPE

The current operational state of this LSP path.

OBJECT-TYPE

For each writable object in this row that can be configured to inherit its value from its corresponding object in the vRtrMplsLspTable, controls whether to inherit the operational value of that object, or use the administratively set value. Non mask bits will always have value of zero, and any attempt to change the value will be silently discarded. This object is a bit-mask, with the following positions: vRtrMplsLspPathHopLimit 0x2000 vRtrMplsLspPathAdminGroupInclude 0x20000 vRtrMplsLspPathAdminGroupExclude 0x40000 vRtrMplsLspPathAdaptive 0x80000 vRtrMplsLspPathOptimizeTimer 0x100000 vRtrMplsLspPathClassType 0x1000000 When the bit for an object is set to one, then the object's administrative and operational value are whatever the DEFVAL or most recently SET value is. The corresponding mask bit will be changed to one when SNMP SET is performed on any of the inherited objects (vRtrMplsLspPathHopLimit, vRtrMplsLspPathAdminGroupInclude, etc). When the bit for an object is set to zero, then the object's administrative and operational value are inherited from the corresponding object in vRtrMplsLspTable.

OBJECT-TYPE

This value identifies the label switched path that is signaled for this entry.

OBJECT-TYPE

The time in 10-millisecond units to signal this path.

OBJECT-TYPE

Primary index into the mplsTunnelARHopTable identifying a particular recorded hop list. A value of 0 implies that there is no recorded hop list associated with this LSP path.

OBJECT-TYPE

The value of vRtrMplsLspPathNegotiatedMTU specifies the size for the Maximum transmission unit (MTU) that is negotiated during establishment of this LSP Path.

OBJECT-TYPE

The value of vRtrMplsLspPathFailCode indicates the reason code for LSP Path failure. A value of 0 indicates that no failure has occurred.

OBJECT-TYPE

The value of vRtrMplsLspPathFailNodeAddr indicates the IP address of the node in the LSP path at which the LSP path failed. When no failure has occurred, this value is 0.

OBJECT-TYPE

The value of vRtrMplsLspPathAdminGroupInclude is a bit-map that specifies a list of admin groups that should be included when this LSP path is setup. If bit 'n' is set, then the admin group with value 'n' is included for this LSP path. This implies that each link that this LSP path goes through must be associated with at least one of the admin groups in the include list. When the vRtrMplsLspPathAdminGroupInclude bit in vRtrMplsLspPathInheritance is cleared (0), the value returned to a GET request is inherited from vRtrMplsLspAdminGroupInclude.

OBJECT-TYPE

The value of vRtrMplsLspPathAdminGroupExclude is a bit-map that specifies a list of admin groups that should be excluded when this LSP path is setup. If bit 'n' is set, then the admin group with value 'n' is excluded for this LSP path. This implies that each link that this LSP path goes through must not be associated with any of the admin groups in the exclude list. When the vRtrMplsLspPathAdminGroupExclude bit in vRtrMplsLspPathInheritance is cleared (0), the value returned to a GET request is inherited from vRtrMplsLspAdminGroupExclude.

OBJECT-TYPE

Setting the value of vRtrMplsLspPathAdaptive to 'true', enables make-before-break functionality for the LSP path. Setting the value to 'false', disables make-before-break functionality for the path. When the vRtrMplsLspPathAdaptive bit in vRtrMplsLspPathInheritance is cleared (0), the value returned to a GET request is inherited from vRtrMplsLspAdaptive.

OBJECT-TYPE

The value of vRtrMplsLspPathOptimizeTimer specifies the time, in seconds, the software will wait before attempting to re-optimize the LSP path. When CSPF is enabled, changes in the network topology may cause the existing path of a loose-hop LSP to become sub-optimal. Such LSPs can be re-optimized and rerouted through more optimal paths by recalculating the path for the LSP at periodic intervals. This interval is controlled by the optimize timer. A value of 0 indicates that optimization has been disabled. When the vRtrMplsLspPathOptimizeTimer bit in vRtrMplsLspPathInheritance is cleared (0), the value returned in the GET request is inherited from vRtrMplsLspOptimizeTimer.

OBJECT-TYPE

The value of vRtrMplsLspPathNextOptimize indicates the current value of the optimize timer. This is the time, in seconds, remaining till the optimize timer will expire and optimization will be started for the LSP path.

OBJECT-TYPE

The value of vRtrMplsLspPathOperBandwidth indicates the amount of bandwidth in megabits per seconds (Mbps) that has been reserved for the operational LSP path. When make-before-break functionality for the LSP is enabled and if the path bandwidth is changed, the resources allocated to the existing LSP paths will not be released until a new path with the new bandwidth settings has been established. While a new path is being signaled, the administrative value and the operational values of the path bandwidth may differ. The value of vRtrMplsLspPathBandwidth specifies the bandwidth requirements for the new LSP path trying to be established whereas the value of vRtrMplsLspPathOperBandwidth specifies the bandwidth reserved for the existing LSP path.

OBJECT-TYPE

The value of vRtrMplsLspPathMBBState indicates the state of the most recent invocation of the make-before-break functionality. Possible states are: none (1) - no make-before-break invoked success (2) - make-before-break successful inProgress (3) - make-before-break in progress fail (4) - make-before-break failed. This object was made obsolete in release 6.0 R4 and replaced with vRtrMplsLspPathLastMBBState.

OBJECT-TYPE

Setting the value of vRtrMplsLspPathResignal to 'doAction' triggers the resignaling of the LSP path. If the LSP path is operationally down either due to network failure or due to the retry attempts count being exceeded, setting this variable to 'doAction' will initiate the signaling for the path. A make-before-break signaling for the path will be initiated if the LSP is operationally up but the make-before-break retry attempts count was exceeded. Make-before-break signaling will also be initiated for any LSP that is operationally up. This may be used to cause a loose-hop LSP to be optimized. If a resignal is triggered while a resignaling is already in progress, the old transient state will be destroyed and a new transaction being triggered. An SNMP GET request on this object should return 'notApplicable'.

OBJECT-TYPE

Primary index into the vRtrMplsTunnelCHopTable identifying a particular computed hop list. A value of 0 implies that there is no computed hop list associated with this LSP path.

OBJECT-TYPE

The value of vRtrMplsLspPathOperMTU indicates the size for the Maximum transmission unit (MTU) that is currently operation for this LSP Path.

OBJECT-TYPE

When the value of vRtrMplsLspPathRecordLabel is 'record', recording of labels at each node that a LSP traverses is enabled. When the value of vRtrMplsLspPathRecordLabel is 'noRecord', recording of labels at each node that a LSP traverses is disabled.

OBJECT-TYPE

The value of vRtrMplsLspPathSrlg specifies whether the use of SRLG constraint in the computation of a secondary path for an LSP at the head-end Label Edge Router (LER) is enabled. The value vRtrMplsLspPathSrlg is used only when the value of vRtrMplsLspPathType is 'secondary'. When the value of vRtrMplsLspPathSrlg is true, the use of SRLG constraint in the computation of a secondary path is enabled.

OBJECT-TYPE

The value of vRtrMplsLspPathSrlgDisjoint indicates whether the relevant standby lsp path is SRLG disjoint from the associated primary lsp path for an LSP at the head-end Label Edge Router (LER). The value vRtrMplsLspPathSrlgDisjoint is used only when the value of vRtrMplsLspPathType is 'standby'. When the value of vRtrMplsLspPathSrlgDisjoint is 'true', primary and standby lsp path do not have SRLG membership in common. When the value of vRtrMplsLspPathSrlgDisjoint is 'false', primary and standby lsp path have SRLG membership in common.

OBJECT-TYPE

The value of vRtrMplsLspPathLastResigAttempt indicates the sysUpTime when the last attempt to resignal this LSP was made.

OBJECT-TYPE

The value of vRtrMplsLspPathMetric indicates the cost of the traffic engineered path returned by the IGP.

OBJECT-TYPE

The value of vRtrMplsLspPathLastMBBType indicates the type of last Make-before-break (MBB). If 'none', then no MBB has been attempted.

OBJECT-TYPE

The value of vRtrMplsLspPathLastMBBEnd indicates the sysUpTime when the last MBB ended.

OBJECT-TYPE

The value of vRtrMplsLspPathLastMBBMetric indicates the cost of the traffic engineered path for the LSP path prior to MBB.

OBJECT-TYPE

The value of vRtrMplsLspPathLastMBBState indicates whether the last Make-before-break was successful or failed. Possible states are: none (1) - no make-before-break invoked success (2) - make-before-break successful fail (3) - make-before-break failed.

OBJECT-TYPE

The value of vRtrMplsLspPathMBBTypeInProg indicates the type of the Make-before-break (MBB) that is in progress. If 'none', then no MBB is in progress.

OBJECT-TYPE

The value of vRtrMplsLspPathMBBStarted indicates the sysUpTime when the in-progress MBB started.

OBJECT-TYPE

The value of vRtrMplsLspPathMBBNextRetry indicates the amount of time remaining in seconds before the next attempt is made to retry the in-progress MBB.

OBJECT-TYPE

The value of vRtrMplsLspPathMBBRetryAttempts indicates 'n' where nth attempt for the MBB is in progress.

OBJECT-TYPE

The value of vRtrMplsLspPathMBBFailCode indicates the reason code for in-progress MBB failure. A value of 'none' indicates that no failure has occurred.

OBJECT-TYPE

The value of vRtrMplsLspPathMBBFailNodeArType indicates the type of vRtrMplsLspPathMBBFailNodeAddr. A value of 'unknown' indicates that no failure has occurred.

OBJECT-TYPE

The value of vRtrMplsLspPathMBBFailNodeAddr indicates the IP address of the node in the LSP path at which the in-progress MBB failed. A value of 'unknown' for vRtrMplsLspPathMBBFailNodeArType and empty string for vRtrMplsLspPathMBBFailNodeAddr indicates that no failure has occurred.

OBJECT-TYPE

The value of vRtrMplsLspPathClassType specifies the class type (CT) associated with this LSP path. When the vRtrMplsLspPathClassType bit in vRtrMplsLspPathInheritance is cleared (0), the value returned to a GET request is inherited from vRtrMplsLspClassType.

OBJECT-TYPE

The value of vRtrMplsLspPathOperMetric indicates the operational metric for the LSP path.

OBJECT-TYPE

The value of vRtrMplsLspPathResignalEligible indicates that the LSP path is eligible for resignaling on the basis of available bandwidth.

OBJECT-TYPE

The value of vRtrMplsLspPathIsFastRetry indicates which retry timer is being referred to by vRtrMplsLspPathRetryTimeRemaining. When the value of vRtrMplsLspPathIsFastRetry is set to 'true', vRtrMplsLspPathRetryTimeRemaining is referring to either the P2P active path fast timer, vRtrMplsGenP2pActPathFastRetry or the secondary fast retry timer, vRtrMplsGeneralSecFastRetryTimer. When the value of vRtrMplsLspPathIsFastRetry is set to 'false', vRtrMplsLspPathRetryTimeRemaining is referring to the LSP retry timer, vRtrMplsLspRetryTimer.

OBJECT-TYPE

The value of vRtrMplsLspPathBackupCT specifies the backup class type (CT) associated with the LSP. A value of -1 indicates that no backup class type has been configured for the LSP.

OBJECT-TYPE

The value of vRtrMplsLspPathMainCTRetryRem indicates the number of remaining attempts the software should make before it can start using the backup class type for the LSP.

OBJECT-TYPE

The value of vRtrMplsLspPathOperCT indicates operational class type (CT) associated with the LSP. A value of -1 indicates that no operational class type has been configured for the LSP

OBJECT-TYPE

The value of vRtrMplsLspPathNewPathIndex specifies the index for the new path in mplsTunnelTable.

OBJECT-TYPE

The value of vRtrMplsLspPathMBBMainCTRetryRem indicates the number of remaining attempts the software should make before it can start using the backup class type for the LSP.

OBJECT-TYPE

The value of vRtrMplsLspPathSigBWMBBInProg indicates the bandwidth used to signal the MBB currently in progress.

OBJECT-TYPE

The value of vRtrMplsLspPathSigBWLastMBB indicates the bandwidth used to signal the last MBB that occurred.

OBJECT-TYPE

The value of vRtrMplsLspPathActiveByManual indicates whether a secondary standby path has become the active LSP path due to manual intervention. When vRtrMplsLspSwitchStbyPath is set to 'doAction' a manual switch is attempted. When vRtrMplsLspSwitchStbyPathForce is set to 'true' the manual switch is forced. When the value of vRtrMplsLspPathActiveByManual is set to 'notApplicable', the LSP path is active but not due to any manual intervention. When the value of vRtrMplsLspPathActiveByManual is set to 'noForce', the LSP path has become active by a manual switch specified by the user. When the value of vRtrMplsLspPathActiveByManual is set to 'force', the LSP path has become active by a forced manual switch executed by the user.

OBJECT-TYPE

The value of vRtrMplsLspPathTimeoutIn indicates the amount of time remaining, in seconds, for the LSP path state to time out after the initial PATH message has been sent. If the timer expires and the LSP path has not become operationally up, the LSP path is torn down and the retry timer is started to schedule a new retry cycle.

OBJECT-TYPE

The value of vRtrMplsLspPathMBBTimeoutIn indicates the amount of time remaining, in seconds, for the in-progress MBB path state to time out after the initial PATH message has been sent. If the timer expires and the in-progress MBB path has not become operationally up, the MBB path is torn down and the retry timer is started to schedule a new retry cycle.

OBJECT-TYPE

The value of vRtrMplsLspPathBfdTemplateName specifies the TIMETRA-BFD-MIB::tmnxBfdAdminTemplateName used by this LSP path.

OBJECT-TYPE

The value of vRtrMplsLspPathBfdEnable specifies whether BFD is enabled or not for this LSP path.

OBJECT-TYPE

The value of vRtrMplsLspPathBfdPingIntvl specifies the time interval for periodic LSP ping for BFD bootstrapping. The object vRtrMplsLspPathBfdPingIntvl is applicable to LSPs with vRtrMplsLspType set to 'dynamic'. When the value of vRtrMplsLspPathBfdPingIntvl is set to '0', it disables LSP pings for BFD bootstrapping.

OBJECT-TYPE

The value of vRtrMplsLspPathLastUpdateTime indicates the sysUpTime when the last update occurred

OBJECT-TYPE

The value of vRtrMplsLspPathLastUpdateId indicates the last update ID which was processed.

OBJECT-TYPE

The value of vRtrMplsLspPathLastUpdateState indicates whether the last update was successful or failed. Possible states are none (1) - no update invoked success (2) - update successful fail (3) - updated failed

OBJECT-TYPE

The value of vRtrMplsLspPathLastUpdFailCode indicates the reason code for in-progress update failure. A value of 'none' indicates that no failure has occurred.

OBJECT-TYPE

The value of vRtrMplsLspPathBfdUpWaitTimer specifies the time in seconds the software will wait for the BFD session to come up. The timer object is applicable for LSPs with vRtrMplsLspType set to 'srTe'. The timer is started when BFD is first enabled on a path or BFD transitions from up to down. When this timer expires and if BFD session has not yet come up, the path is torn down by removing it from TTM and the IOM and the retry timer is started.

OBJECT-TYPE

The value of vRtrMplsLspPathBfdUpWaitTmLeft indicates the time in seconds remaining in the vRtrMplsLspPathBfdUpWaitTimer.

OBJECT-TYPE

The value of vRtrMplsLspPathBfdState indicates state of the BFD session on the LSP path.

OBJECT-TYPE

The value of vRtrMplsLspPathBfdStartFailRsn indicates the failure reason when vRtrMplsLspPathBfdState is value 'failToStart'.

OBJECT-TYPE

The value of vRtrMplsLspPathBfdOperUpWaitTmr indicates operational value of the time in seconds the software will wait for the BFD session to come up. When value of vRtrMplsLspPathBfdEnable to 'true', vRtrMplsLspPathBfdOperUpWaitTmr will be set to vRtrMplsLspPathBfdUpWaitTimer. When value of vRtrMplsLspBfdEnable to 'true', vRtrMplsLspPathBfdOperUpWaitTmr will be set to vRtrMplsLspExtBfdUpWaitTimer. When vRtrMplsLspPathBfdEnable and vRtrMplsLspBfdEnable are set to 'false', the value of vRtrMplsLspPathBfdOperUpWaitTmr is set to 0.

OBJECT-TYPE

The current operational state for self-ping for this LSP path.

OBJECT-TYPE

The vRtrMplsLspPathStatTable has an entry for an association between a Labeled Switch Path (LSP) in the vRtrMplsLspTable and a path (or tunnel) entry in the mplsTunnelTable.

OBJECT-TYPE

Each row entry represents a collection of statistics for an association between a Labeled Switch Path (LSP) in the vRtrMplsLspTable and a path (or tunnel) entry in the mplsTunnelTable. Entries cannot be created and deleted via SNMP SET operations.

OBJECT-TYPE

The total time in 10-millisecond units that this LSP path has been operational. For example, the percentage up time can be determined by computing (vRtrMplsLspPathTimeUp/vRtrMplsLspAge * 100 %).

OBJECT-TYPE

The total time in 10-millisecond units that this LSP Path has not been operational.

OBJECT-TYPE

The number of unsuccessful attempts which have been made to signal this path. As soon as the path gets signalled, this is set to 0.

OBJECT-TYPE

The object vRtrMplsLspPathTransitionCount maintains the number of transitions that have occurred for this LSP.

OBJECT-TYPE

The value of vRtrMplsLspPathCspfQueries indicates the number of CSPF queries that have been made for this LSP path.

OBJECT-TYPE

This table has an entry for each mplsXCEntry in the mplsXCTable. It serves as an another indirect index to the mplsXCTable.

OBJECT-TYPE

An entry in this table represents the indices to be used to search the mplsXCTable.

OBJECT-TYPE

An index of the mplsXCTable. It represents mplsXCIndex, a field of the mplsXCTable.

OBJECT-TYPE

An index of the mplsXCTable. It represents mplsInSegmentIfIndex of the mplsInSegmentTable.

OBJECT-TYPE

An index of the mplsXCTable. It represents mplsInSegmentLabel of the mplsInSegmentTable.

OBJECT-TYPE

An index of the mplsXCTable. It represents mplsOutSegmentIndex of the mplsOutSegmentTable.

OBJECT-TYPE

Primary index into the mplsTunnelHopTable identifying a particular recorded hop list (stores ERO in LSR).

OBJECT-TYPE

Primary index into the mplsTunnelARHopTable identifying a particular recorded hop list (stores RRO in LSR).

OBJECT-TYPE

An index into the TIMETRA-RSVP-MIB::vRtrRsvpSessionTable identifying a particular RSVP session.

OBJECT-TYPE

The value of vRtrMplsXCFailCode indicates the reason code for cross-connect failure. A value of 0 indicates that no failure occurred.

OBJECT-TYPE

Index to the vRtrMplsTunnelCHopTable entries that specify the hops for the CSPF path for a detour LSP for this tunnel.

OBJECT-TYPE

The vRtrMplsGeneralTable contains objects for general control and management of an MPLS protocol instance within a virtual router.

OBJECT-TYPE

Each row entry represents an instance of the MPLS protocol running within a virtual router. Entries in this table cannot be created and deleted via SNMP SET operations. An entry in this table is created by the agent when vRtrMplsStatus in the vRtrConfTable is set to 'create'. The entry is destroyed when vRtrMplsStatus is set to 'delete'

OBJECT-TYPE

The sysUpTime when this row was last modified.

OBJECT-TYPE

When vRtrMplsGeneralAdminState is set to 'inService', the agent attempts to enable the MPLS protocol instance on this router. When vRtrMplsGeneralAdminState is set to 'outOfService', the agent attempts to disable the MPLS protocol instance on this router.

OBJECT-TYPE

vRtrMplsGeneralOperState indicates the current operating state of this MPLS protocol instance on this router.

OBJECT-TYPE

When vRtrMplsGeneralPropagateTtl is set to 'true', for all LSPs, the ingress ESR writes the TTL of the IP packet in the label and each transit ESR decrements the TTL in the label. At the egress ESR the TTL value from the label is written into the IP packet. When vRtrMplsGeneralPropagateTtl is set to 'false', the ingress ESR ignores the IP packet TTl and writes the value of 255 into the label, while the egress ESR does not write the label TTL into the IP packet. This assumes that all ESRs have been configured to have vRtrMplsGeneralPropagateTtl set to 'false', or this may result in unpredictable behavior. This object was made obsolete in release 11.0.

OBJECT-TYPE

The value of vRtrMplsGeneralTE specifies the type of traffic engineering used with this MPLS instance. This object was made obsolete in release 11.0.

OBJECT-TYPE

This object is used to assign values to vRtrMplsLspIndex as described in 'Textual Conventions for SNMPv2'. The network manager reads the object, and then writes the value back in the SET request that creates a new instance of vRtrMplsLspEntry. If the SET fails with the code 'inconsistentValue', then the process must be repeated. If the the SET succeeds, then the object is incremented and the new instance is created according to the manager's directions.

OBJECT-TYPE

The value of vRtrMplsGeneralOptimizeTimer specifies the time, in seconds, the software will wait before attempting to re-optimize the LSPs. When CSPF is enabled, changes in the network topology may cause the existing path of a loose-hop LSP to become sub-optimal. Such LSPs can be re-optimized and rerouted through more optimal paths by recalculating the path for the LSP at periodic intervals. This interval is controlled by the optimize timer. A value of 0 indicates that optimization has been disabled. The value for vRtrMplsGeneralOptimizeTimer is by default inherited by all LSPs and their paths.

OBJECT-TYPE

The value of vRtrMplsGeneralFRObject specifies whether fast reroute, for LSPs using 'Facility Backup', is signalled with or without the fast reroute object. The value of vRtrMplsGeneralFRObject is ignored if fast reroute is disabled for the LSP or if the LSP is using 'One-to-one Backup'. The value for vRtrMplsGeneralFRObject is by default inherited by all LSPs.

OBJECT-TYPE

The value of vRtrMplsGeneralResignalTimer specifies the value for the P2P (point-to-point) LSP resignal timer, that is the time, in minutes, the software will wait before attempting to resignal the P2P LSPs. When the resignal timer expires, if the new recorded hop list (RRO) for an P2P LSP has a better metric than the current recorded hop list, an attempt will be made to resignal that P2P LSP using the make-before-break mechanism. If the attempt to resignal an P2P LSP fails, the P2P LSP will continue to use the existing path and a resignal will be attempted the next time the timer expires. A value of 0 for the resignal timer indicates that timer-based P2P LSP resignalling has been disabled.

OBJECT-TYPE

The value of vRtrMplsGeneralHoldTimer specifies the time, in seconds, for which the ingress node holds a bit before programming its data plane and declaring the lsp up to the service module. A value of 0 indicates that the hold timer has been disabled.

OBJECT-TYPE

The value of vRtrMplsGeneralDynamicBypass specifies whether dynamic bypass tunnels are enabled. By default, dynamic bypass tunnels are enabled.

OBJECT-TYPE

The value of vRtrMplsGeneralNextResignal indicates the time remaining, in minutes, for the vRtrMplsGeneralResignalTimer to expire.

OBJECT-TYPE

The value of vRtrMplsGeneralOperDownReason indicates the reason due to which the MPLS instance is operationally down.

OBJECT-TYPE

The value of vRtrMplsGeneralSrlgFrr specifies whether Shared Risk Link Group (SRLG) constraint will be used in the computation of FRR bypass or detour to be associated with any primary LSP path on the system. When the value of vRtrMplsGeneralSrlgFrr is 'true' the use of SRLG constraint is enabled. By default, the use of SRLG constraint is disabled.

OBJECT-TYPE

The value of vRtrMplsGeneralSrlgFrrStrict specifies whether to associate the LSP with a bypass or signal a detour if a bypass or detour satisfies all other constraints except the SRLG constraints. When the value of vRtrMplsGeneralSrlgFrrStrict is 'true' and a path that meets SRLG constraints is not found, the bypass or detour is not setup. If this value is set to 'true' when vRtrMplsGeneralSrlgFrr is set to 'false', vRtrMplsGeneralSrlgFrr is set to 'true' also. By default, the value of vRtrMplsGeneralSrlgFrrStrict is 'false'.

OBJECT-TYPE

The value of vRtrMplsGeneralNewP2mpInstIndex specifies the object that is used to assign values to vRtrMplsP2mpInstIndex as described in 'Textual Conventions for SNMPv2'. The network manager reads the object, and then writes the value back in the SET request that creates a new instance of vRtrMplsP2mpInstEntry. If the SET fails with the code 'inconsistentValue', then the process must be repeated. If the the SET succeeds, then the object is incremented and the new instance is created according to the manager's directions.

OBJECT-TYPE

The value of vRtrMplsGeneralLeastFillMinThd specifies in percentage the least minimum threshold parameter used in the least-fill path selection process. When comparing the percentage of least available link bandwidth across the sorted paths, whenever two percentages differ by less than the value configured as the vRtrMplsGeneralLeastFillMinThd, CSPF will consider them equal and will apply a random number generator to select the path among these paths.

OBJECT-TYPE

The value of vRtrMplsGenLeastFillReoptiThd specifies in percentage the least reoptimization threshold parameter used in the least-fill path selection process. During a timer-based resignaling of an LSP path which has vRtrMplsLspLeastFill enabled, CSPF will first update the least-available bandwidth figure for the current path of this LSP. It then applies the least-fill path selection method to select a new path for this LSP. If the new computed path has the same cost as the current path, it will compare the least-available bandwidth figures of the two paths and if the difference exceeds vRtrMplsGenLeastFillReoptiThd, a trap will be generated to indicate that a better least-fill path is available for this LSP.

OBJECT-TYPE

The value of vRtrMplsGeneralUseSrlgDB specifies whether the use of the user SRLG database by CSPF is enabled.

OBJECT-TYPE

The value of vRtrMplsGeneralP2mpResigTimer specifies the value for the P2MP (point to multi point) LSP resignal timer, that is the time, in minutes, the software will wait before attempting to resignal the P2MP LSPs. When the resignal timer expires, an attempt to resignal the entire P2MP instance comprising all source to leaf (S2Ls) are done, the IGP or TE metric of the S2Ls are not taken into consideration. If the attempt to resignal an P2MP LSP fails, the P2MP LSP will continue to use the existing S2Ls and a resignal will be attempted the next time the timer expires. A value of 0 for the resignal timer indicates that timer-based P2MP LSP resignalling has been disabled.

OBJECT-TYPE

The value of vRtrMplsGeneralP2mpNextResignal indicates the time remaining, in minutes, for the vRtrMplsGeneralP2mpResigTimer to expire.

OBJECT-TYPE

The value of vRtrMplsGeneralSecFastRetryTimer specifies the value, in seconds, used as fast retry timer for a secondary path. If the first attempt to setup a secondary path fails due to a path error, the fast retry timer will be started for the secondary path so that the path can be retried sooner. If the next attempt also fails, further retries for the path will use the configured value for LSP retry timer, vRtrMplsLspRetryTimer. If retry timer for the LSP is configured to be less than the MPLS secondary-fast-retry-timer, all retries for the secondary path will use the LSP retry timer. A value of 0 indicates that fast retry for secondary paths has been disabled.

OBJECT-TYPE

The value of vRtrMplsGeneralShortTTLPropLocal specifies whether or not to enable the propagation of time to live (TTL) from the IP packet header into the header of the resulting MPLS packet for all local packets forwarded over a LSP shortcut. When the value is 'true' TTL is propagated from the IP packet header into the header of the resulting MPLS packet.

OBJECT-TYPE

The value of vRtrMplsGeneralShortTTLPropTrans specifies whether or not to enable the propagation of time to live (TTL) from the IP packet header into the header of the resulting MPLS packet for all transit packets forwarded over a LSP shortcut. When the value is 'true' TTL is propagated from the IP packet header into the header of the resulting MPLS packet.

OBJECT-TYPE

The value of vRtrMplsGeneralStaticLspFRTimer specifies the audit time for static LSPs which are not currently up.

OBJECT-TYPE

The value of vRtrMplsGeneralAutoBWDefSampMul specifies the global default for collection intervals in a sample interval.

OBJECT-TYPE

The value of vRtrMplsGeneralAutoBWDefAdjMul specifies the global default for collection intervals in an adjust interval.

OBJECT-TYPE

The value of vRtrMplsGeneralExpBackoffRetry specifies the state of Exponential Backoff Retry mechanism.

OBJECT-TYPE

The value of vRtrMplsGeneralCspfOnLooseHop specifies whether the Constrained Shortest Path First (CSPF) calculation till the next loose hop is enabled or not.

OBJECT-TYPE

The value of vRtrMplsGeneralP2PMaxByPassAssoc specifies the maximum number of LSP primary paths that can associate with each manual or dynamic bypass point-to-point (P2P) LSP.

OBJECT-TYPE

The value of vRtrMplsGenP2pActPathFastRetry specifies the time, in seconds, active path point-to-point (P2P) LSP waits before it attempts to re-establish itself. This timer is started after first attempt to setup active path P2P LSP fails. When vRtrMplsGenP2pActPathFastRetry is set to 0, fast retry timer for active path P2P LSP is disabled.

OBJECT-TYPE

The value of vRtrMplsGenP2mpS2lFastRetry specifies the time, in seconds, active path point to multipoint (P2MP) source to leaf (S2L) LSP waits before it attempts to re-establish itself. This timer is started after first attempt to setup active path P2MP S2L LSP fails. When vRtrMplsGenP2mpS2lFastRetry is set to 0, fast retry timer for active path P2MP S2L LSP is disabled.

OBJECT-TYPE

The value of vRtrMplsGenLspInitRetryTimeout specifies the amount of time in seconds the software waits for an LSP path to come up after sending out the initial Path message. If the initial retry timeout period expires and the LSP path is not up, it is torn down and the LSP retry timer is started to schedule a new retry cycle using a new LSPId.

OBJECT-TYPE

The value of vRtrMplsLoggerEventBundling specifies whether or not the notification bundling mechanism is enabled. When the value of vRtrMplsLoggerEventBundling is set to 'true', all TIMETRA-SYSTEM-MIB::tmnxConfigCreate and TIMETRA-SYSTEM-MIB::tmnxConfigDelete notifications that are generated because of creation or deletion of entries in the vRtrMplsXCTable during quiet period of 2 minutes are bundled in a single notification. An entry is created or deleted in vRtrMplsXCTable when a RSVP session is created or deleted on this ingress, transit or egress router instance causing creation or deletion of an entry in TIMETRA-RSVP-MIB::vRtrRsvpSessionTable. A vRtrMplsXCBundleChange notification is generated after every quiet interval of 2 minutes if one or more RSVP session changed state and retained that state during the quiet interval. However if the state of the RSVP sessions does not remain stable for an entire quiet interval, the notification is generated after the maximum interval period of 10 minutes has elapsed.

OBJECT-TYPE

The value of vRtrMplsGenIssuMplsLockdown indicates if MPLS has entered the state of not accepting new requests for creation of LSPs (local/transit) during the minor ISSU(In Service Software Update) operation.

OBJECT-TYPE

The value of vRtrMplsGenFRAdminGroup specifies whether or not the use of administrative group constraints on a FRR backup LSP at a Point-of-Local Repair(PLR) node is enabled. When the value of vRtrMplsGenFRAdminGroup is set to 'true', each PLR node reads the admin group constraints in the FAST_REROUTE object in the Path message of the LSP primary path. If the FAST_REROUTE object is not included in the Path message, then the PLR will read the admin group constraints from the Session Attribute object in the Path message.

OBJECT-TYPE

The value of vRtrMplsGenRetryOnIgpOverload specifies whether or not to teardown LSPs transiting through nodes that are in IGP overload state. When the value of vRtrMplsGenRetryOnIgpOverload is set to 'true' and a node is reporting that it is in IGP overload state, MPLS will tear- down and retry LSP paths that are transiting through the overloaded node. When the value of vRtrMplsGenRetryOnIgpOverload is set to 'false' and a node is reporting that it is in IGP overload state, MPLS will not tear down LSP paths that are transiting through the overloaded node.

OBJECT-TYPE

The value of vRtrMplsGenMbbPrefCurrentHops specifies whether or not Constrained Shortest Path First (CSPF) for a Make-before-break (MBB) path should give preference to hops/links used by the current Labeled Switch Path (LSP).

OBJECT-TYPE

The value of vRtrMplsGeneralBypassResigTimer specifies the value for the Bypass LSP resignal timer, that is the time, in minutes, the software will wait before attempting to resignal Bypass LSPs. When the resignal timer expires, if the new CSPF path for a Bypass LSP has a better metric than the current CSPF path, an attempt will be made to resignal that Bypass LSP. If the attempt to resignal the Bypass LSP fails, the FRR LSPs protected by that Bypass LSP will continue to use that Bypass LSP and a resignal will be attempted the next time the timer expires. A value of 0 for the resignal timer indicates that timer-based Bypass LSP resignalling has been disabled.

OBJECT-TYPE

The value of vRtrMplsGenBypassNextResignal indicates the time remaining, in minutes, for the vRtrMplsGeneralBypassResigTimer to expire.

OBJECT-TYPE

The value of vRtrMplsGeneralNewLspSRIndex is used to specify values assigned to vRtrMplsLspIndex for Segment Routing LSPs. The network manager reads the object, and then writes the value back in the SET request that creates a new instance of vRtrMplsLspEntry. If the SET fails with the code 'inconsistentValue', then the process must be repeated. If the the SET succeeds, then the object is incremented and the new instance is created according to the manager's directions. The range for Segment Routing LSPs is as specified in the textual convention for vRtrMplsLspIndex.

OBJECT-TYPE

The set of configured TE properties for this LSP expressed as a bit map.

OBJECT-TYPE

The value of vRtrMplsGeneralEntropyLblRsvpTe specifies whether the application takes into account the value of Entropy Label and Entropy Label Capability in the label stack for RSVP-TE LSPs. When the value of vRtrMplsGeneralEntropyLblRsvpTe is set to 'enable', the application will account for EL/ELC in the label stack without taking into consideration the value of the enabled ELC. When the value of vRtrMplsGeneralEntropyLblRsvpTe is set to 'force-disable', the application will ignore the value of enabled ELC. When the value of vRtrMplsGeneralEntropyLblRsvpTe is modified, Entropy Label will become operational when this LSP is resignalled. The default value of vRtrMplsGeneralEntropyLblRsvpTe is set to 'enable'.

OBJECT-TYPE

The value of vRtrMplsGeneralEntropyLblSrTe specifies whether the application takes into account the value of Entropy Label and Entropy Label Capability in the label stack for SR-TE LSPs. When the value of vRtrMplsGeneralEntropyLblSrTe is set to 'enable', the application will account for EL/ELC in the label stack without taking into consideration the value of the enabled ELC. When the value of vRtrMplsGeneralEntropyLblSrTe is set to 'force-disable', the application will ignore the value of enabled ELC. When the value of vRtrMplsGeneralEntropyLblSrTe is modified, Entropy Label will become operational when this LSP is resignalled. The default value of vRtrMplsGeneralEntropyLblSrTe is set to 'enable'.

OBJECT-TYPE

The value of vRtrMplsGeneralAuxStats specifies which types of labeled traffic are counted in the MPLS auxiliary statistics table. By default, all labeled traffic is counted in the default MPLS statistics table. If the 'sr' bit is set, Segment Routing traffic is counted in the MPLS auxiliary statistics table.

OBJECT-TYPE

The value of vRtrMplsGenSrTeResignalTimer specifies the value for the SR-TE LSPs resignal timer, that is the time, in minutes, the software will wait before attempting to resignal the SR-TE LSPs. When the resignal timer expires, if the new recorded hop list (RRO) for an SR-TE LSP has a better metric than the current recorded hop list, an attempt will be made to resignal that LSP using the make-before-break mechanism. If the attempt to resignal an SR-TE LSP fails, the LSP will continue to use the existing path and a resignal will be attempted the next time the timer expires. A value of 0 for the resignal timer indicates that timer-based SR-TE LSP resignalling has been disabled.

OBJECT-TYPE

The value of vRtrMplsGenMaxBypassPlrAssoc specifies the maxiumum bypass PLR assocations.

OBJECT-TYPE

The value of vRtrMplsGenLspSelfPingInterval specifies the interval duration at which LSP self ping packets are sent until a reply is received from the far end of the session ID.

OBJECT-TYPE

The value of vRtrMplsGenLspSelfPingTimeout specifies the value of timeout expiry duration up to which the lsp-self-ping packets will be sent. If the timeout expires before an LSP self ping has been received, then the system should tear down the path and go back to CSPF for a new path

OBJECT-TYPE

The value of vRtrMplsGenLspSelfPingRsvpTe specifies whether the application takes into account the value of Self Ping in the label stack of RSVP-TE LSPs. When the value of vRtrMplsGenLspSelfPingRsvpTe is set to 'enable', the application will take into consideration the values of vRtrMplsGenLspSelfPingInterval and vRtrMplsGenLspSelfPingTimeout. When the value of vRtrMplsGenLspSelfPingRsvpTe is set to 'disable', the application will not take into consideration the values of vRtrMplsGenLspSelfPingInterval and vRtrMplsGenLspSelfPingTimeout.

OBJECT-TYPE

The value of vRtrMplsGenSrTeResigOnIgpEvent specifies re-optimization of SR-TE LSPs triggered by IGP events is enabled or disabled.

OBJECT-TYPE

vRtrMplsGeneralV6OperState indicates the current operating state of MPLS protocol instance on this router for srte ipv6.

OBJECT-TYPE

The value of vRtrMplsGeneralV6OperDownReason indicates the reason due to which the MPLS instance is operationally down for srte ipv6.

OBJECT-TYPE

The value of vRtrMplsGenSrteNextResignal indicates the time remaining, in minutes, for the vRtrMplsGenSrTeResignalTimer to expire.

OBJECT-TYPE

The vRtrMplsGeneralStatTable contains statistics for an MPLS protocol instance within a virtual router.

OBJECT-TYPE

Each row entry represents a collection of statistics for an instance of the MPLS protocol running within a virtual router. Entries cannot be created and deleted via SNMP SET operations.

OBJECT-TYPE

The value of vRtrMplsGeneralStaticLspOriginate indicates the number of static LSPs that originate at this virtual router.

OBJECT-TYPE

The value of vRtrMplsGeneralStaticLspTransit indicates the number of static LSPs that transit through this virtual router.

OBJECT-TYPE

The value of vRtrMplsGeneralStaticLspTerminate indicates the number of static LSPs that terminate at this virtual router.

OBJECT-TYPE

The value of vRtrMplsGeneralDynamicLspOriginate indicates the number of dynamic LSPs that originate at this virtual router.

OBJECT-TYPE

The value of vRtrMplsGeneralDynamicLspTransit indicates the number of dynamic LSPs that transit through this virtual router.

OBJECT-TYPE

The value of vRtrMplsGeneralDynamicLspTerminate indicates the number of dynamic LSPs that terminate at this virtual router.

OBJECT-TYPE

The value of vRtrMplsGeneralDetourLspOriginate indicates the number of detour LSPs that originate at this virtual router.

OBJECT-TYPE

The value of vRtrMplsGeneralDetourLspTransit indicates the number of detour LSPs that transit through this virtual router.

OBJECT-TYPE

The value of vRtrMplsGeneralDetourLspTerminate indicates the number of detour LSPs that terminate at this virtual router.

OBJECT-TYPE

The value of vRtrMplsGeneralS2lOriginate indicates the number of source to leaf (S2L) sub LSP path called as S2L here that originate at this virtual router.

OBJECT-TYPE

The value of vRtrMplsGeneralS2lTransit indicates the number of S2Ls that transit through this virtual router.

OBJECT-TYPE

The value of vRtrMplsGeneralS2lTerminate indicates the number of S2Ls that terminate at this virtual router.

OBJECT-TYPE

The value of vRtrMplsGeneralLspEgrStatCount indicates the number of LSP egress statistics configured on this virtual router.

OBJECT-TYPE

The value of vRtrMplsGeneralLspIgrStatCount indicates the number of LSP ingress statistics configured on this virtual router.

OBJECT-TYPE

The value of vRtrMplsGenMplsTpLspOriginate indicates the number of MPLS TP LSPs that originate at this virtual router.

OBJECT-TYPE

The value of vRtrMplsGenMplsTpLspTransit indicates the number of MPLS TP LSPs that transit through this virtual router.

OBJECT-TYPE

The value of vRtrMplsGenMplsTpLspTerminate indicates the number of MPLS TP LSPs that terminate at this virtual router.

OBJECT-TYPE

The value of vRtrMplsGenMplsTpOrigPathInst indicates the number of MPLS TP LSPs originate path instances.

OBJECT-TYPE

The value of vRtrMplsGenMplsTpTranPathInst indicates the number of MPLS TP LSPs transit path instances.

OBJECT-TYPE

The value of vRtrMplsGenMplsTpTermPathInst indicates the number of MPLS TP LSPs terminated path instances.

OBJECT-TYPE

The value of vRtrMplsGeneralMeshP2pOriginate indicates the number of Mesh P2P LSPs originating at this virtual router.

OBJECT-TYPE

The value of vRtrMplsGeneralOneHopP2pOrigin indicates the number of One Hop P2P LSPs originating at this virtual router.

OBJECT-TYPE

The value of vRtrMplsGeneralSrTeLspOriginate indicates the number of Segment Routing TE LSPs that are originating at this virtual router.

OBJECT-TYPE

The value of vRtrMplsGenMeshP2PSrTeLspOrig indicates the number of Mesh P2P Segment Routing TE LSPs that are originating at this virtual router.

OBJECT-TYPE

The value of vRtrMplsGenOneHopP2PSrTeLspOrig indicates the number of One-Hop P2P Segment Routing TE LSPs that are originating at this virtual router.

OBJECT-TYPE

The value of vRtrMplsGenPceInitP2PSrTeLspOrig indicates the number of PCE Init P2P Segment Routing TE LSPs that are originating at this virtual router.

OBJECT-TYPE

The value of vRtrMplsGenLspSelfPingTimeouts indicate the number of LSP self-ping timeouts for LSPs originating at this virtual router.

OBJECT-TYPE

The vRtrMplsIfTable has an entry for each router interface configured for MPLS in the system.

OBJECT-TYPE

Each row entry represents an interface on this virtual router that participates in the MPLS protocol. A row cannot be created or deleted via SNMP SET requests. A row with default attribute values is created by setting the vRtrIfEntry attribute, vRtrIfMplsStatus, to 'create'. A row is removed if vRtrIfMplsStatus is set to 'delete'. However, an attempt to destroy a row will fail if vRtrMplsIfAdminState has not first been set to 'outOfService'.

OBJECT-TYPE

The desired administrative state for the MPLS protocol running on this MPLS interface.

OBJECT-TYPE

This variable indicates the current status of the MPLS protocol running on this MPLS interface. When the TIMETRA-VRTR-MIB::vRtrIfPortID object of this interface is set to a loopback port identifier, the operational state is not relevant and an SNMP GET request on this object will return 'unknown'.

OBJECT-TYPE

The value of vRtrMplsIfAdminGroup is a bit-map that identifies the admin groups to which the interface belongs. If bit 'n' is set, then the interface belongs to the admin group with value 'n'. By default, the interface does not belong to any admin groups.

OBJECT-TYPE

The value of vRtrMplsIfTeMetric specifies the traffic engineering metric for this interface. The TE metric is exchanged in addition to the IGP metric by the IGPs. Depending on the value configured for vRtrMplsLspCspfTeMetricEnabled, either the TE metric or the native IGP metric is used in CSPF computations of the LSP paths. The maximum value that can be configured is a 24 bit value.

OBJECT-TYPE

This variable indicates the current status of the MPLS protocol running on this MPLS interface for srte ipv6. When the TIMETRA-VRTR-MIB::vRtrIfPortID object of this interface is set to a loopback port identifier, the operational state is not relevant and an SNMP GET request on this object will return 'unknown'.

OBJECT-TYPE

The vRtrMplsIfStatTable has an entry for each router interface configured for MPLS in the system.

OBJECT-TYPE

Each row entry represents a collection of statistics for an interface on this virtual router that participates in the MPLS protocol. Entries cannot be created and deleted via SNMP SET operations.

OBJECT-TYPE

The total number of MPLS labeled packets transmitted from this interface.

OBJECT-TYPE

The total number of MPLS labeled packets received on this interface.

OBJECT-TYPE

The total number of bytes in MPLS labeled packets transmitted on this interface.

OBJECT-TYPE

The total number of bytes in MPLS labeled packets received on this interface.

OBJECT-TYPE

The total number of SR-MPLS labeled packets transmitted from this interface.

OBJECT-TYPE

The total number of SR-MPLS labeled packets received on this interface.

OBJECT-TYPE

The total number of bytes in SR-MPLS labeled packets transmitted on this interface.

OBJECT-TYPE

The total number of bytes in SR-MPLS labeled packets received on this interface.

OBJECT-TYPE

The vRtrMplsTunnelARHopTable augments the mplsTunnelARHopEntry in the MPLS-TE-MIB.

OBJECT-TYPE

A row entry in this table corresponds to a row entry in the mplsTunnelARHopTable and adds to the information contained in that table

OBJECT-TYPE

If the 'localAvailable' bit is set, it indicates that the link downstream of this node has been protected by means of a local repair mechanism. This mechanism can be either the one-to-one backup method or the facility backup method. If the 'localInUse' bit is set, then it indicates that the local protection mechanism is being used to maintain this tunnel. If the 'bandwidthProtected' bit is set, then it indicates that the backup path is guaranteed to provide the desired bandwidth. If the 'nodeProtected' bit is set, then it indicates that the backup path provides protection against the failure of the next LSR along the LSP. If the 'nodeId' bit is set, it indicates that the address specified in the Record Route Object's IPv4 or IPv6 sub-object is a nodeId address.

OBJECT-TYPE

If label recording is enabled, vRtrMplsTunnelARHopRecordLabel specifies the label that is advertised to the previous hop in the hop list. If label recording is disabled, vRtrMplsTunnelARHopRecordLabel will have a value of 4294967295

OBJECT-TYPE

vRtrMplsTunnelARHopRouterId indicates the router ID of the node corresponding to this hop. vRtrMplsTunnelARHopRouterId is obsoleted in 20.0, replaced by vRtrMplsTunnelARHopNgRouterId

OBJECT-TYPE

The value of vRtrMplsTunnelARHopUnnumIfID indicates the unnumbered interface identifier of this hop. This object should be used in conjunction with vRtrMplsTunnelARHopNgRouterId which would contain the LSR Router ID for the unnumbered interface. If mplsTunnelARHopAddrType is set to unnum(100), then this entry is valid.

OBJECT-TYPE

The value of vRtrMplsTunnelARHopSIDType indicates the type of SID for this hop. When the value of vRtrMplsTunnelARHopSIDType is 'notApplicable', it indicates that this hop is not associated with an SR-TE LSP and hence SID type does not apply for this hop. When the value of vRtrMplsTunnelARHopSIDType is 'nodeSid', it indicates that this hop is associated with an SR-TE LSP and represents a Node SID. When the value of vRtrMplsTunnelARHopSIDType is 'adjacencySid', it indicates that this hop is associated with an SR-TE LSP and represents an Adjacency SID.

OBJECT-TYPE

The value of vRtrMplsTunnelARHopNgRouterId indicates the Router ID of the node corresponding to this hop. Currently IPV6 Router ID is supported by this object. The IP address type of vRtrMplsTunnelARHopNgRouterId is specified by the value of mplsTunnelARHopAddrType. Currently value of 'ipv6' is supported.

OBJECT-TYPE

The vRtrMplsTunnelCHopTable is used to hold the CSPF path for a detour LSP. Each entry indicates a single hop. Primary index is the vRtrMplsTunnelCHopListIndex which associates multiple entries (hops) in the vRtrMplsTunnelCHopTable to a single mplsTunnelEntry specified in the mplsTunnelTable. The first row in the table is the first hop after the origination point of the tunnel.

OBJECT-TYPE

An entry in this table represents a CSPF tunnel hop. Entries are created and deleted by the system.

OBJECT-TYPE

Primary index into this table identifying a particular explicit route object.

OBJECT-TYPE

Secondary index into this table identifying a particular hop.

OBJECT-TYPE

The value of vRtrMplsTunnelCHopAddrType specifies the address type of this tunnel hop. When the value of vRtrMplsTunnelCHopAddrType is 'ipv4', it specifies an IPv4 address type and vRtrMplsTunnelCHopIpv4Addr should be configured. When the value of vRtrMplsTunnelCHopAddrType is 'ipv6', it specifies an IPv6 address type and vRtrMplsTunnelCHopIpv6Addr should be configured. When the value of vRtrMplsTunnelCHopAddrType is 'asNumber', it specifies an AS number and vRtrMplsTunnelCHopAsNumber should be configured. When the value of vRtrMplsTunnelCHopAddrType is 'lspid', it specifies an LSP ID and vRtrMplsTunnelCHopLspId should be configured. When the value of vRtrMplsTunnelCHopAddrType is 'unnum', it specifies an unnumbered interface identifier and vRtrMplsTunnelCHopUnnumIfID should be configured.

OBJECT-TYPE

If vRtrMplsTunnelCHopAddrType is set to ipV4(1), then this value will contain the IPv4 address of this hop. This object is otherwise insignificant and should contain a value of 0.

OBJECT-TYPE

If vRtrMplsTunnelCHopAddrType is ipV4(1), then the prefix length for this hop's IPv4 address is contained herein. This object is otherwise insignificant and should contain a value of 0.

OBJECT-TYPE

If the vRtrMplsTunnelCHopAddrType is set to ipV6(2), then this variable contains the IPv6 address of this hop. This object is otherwise insignificant and should contain a value of 0.

OBJECT-TYPE

If vRtrMplsTunnelCHopAddrType is set to ipV6(2), this value will contain the prefix length for this hop's IPv6 address. This object is otherwise insignificant and should contain a value of 0.

OBJECT-TYPE

If vRtrMplsTunnelCHopAddrType is set to asNumber(3), then this value will contain the AS number of this hop. This object is otherwise insignificant and should contain a value of 0 to indicate this fact.

OBJECT-TYPE

If vRtrMplsTunnelCHopAddrType is set to lspid(4), then this value will contain the LSPID of a tunnel of this hop. The present tunnel being configured is tunneled through this hop (using label stacking). This object is otherwise insignificant and should contain a value of 0 to indicate this fact.

OBJECT-TYPE

Denotes whether this tunnel hop is routed in a strict or loose fashion.

OBJECT-TYPE

The value of vRtrMplsTunnelCHopEgressAdmGrp indicates administrative groups on the egressing interface at the current hop.

OBJECT-TYPE

The value of vRtrMplsTunnelCHopUnnumIfID indicates the unnumbered interface identifier of this hop. This object should be used in conjunction with vRtrMplsTunnelCHopRtrID which would contain the LSR Router ID for the unnumbered interface. If vRtrMplsTunnelCHopAddrType is set to unnum(5), then this entry is valid. This object is otherwise insignificant and should contain a value of 0 to indicate this fact.

OBJECT-TYPE

The value of vRtrMplsTunnelCHopRtrID indicates value of the Router ID for the node when vRtrMplsTunnelCHopAddrType is set to ipV4(1) or unnum(5).

OBJECT-TYPE

The value of vRtrMplsTunnelCHopIsABR indicates whether the current hop is an Area Border Router (ABR) or not.

OBJECT-TYPE

The vRtrMplsAdminGroupTable has an entry for each administrative group configured for the virtual router in the system. Administrative groups are resource constructs that define a link color or resource class. They provide the ability to classify network resources (links) into groups or colors based on zones, geographic location, link location, etc. By doing so, network administrators are able to do more granular traffic engineering of LSPs.

OBJECT-TYPE

Each row entry in the vRtrMplsAdminGroupTable represents an administrative group which is simply a mapping between a group name (an ASCII string) and a group value (a number in the range 0 to 31). Entries in this table are created and deleted via SNMP SET operations. An entry is created by setting the value of vRtrMplsAdminGroupRowStatus to 'createAndWait'. The row status for this entry can be set to active only once the value of vRtrMplsAdminGroupValue has been set to a valid number in the range 0 to 31. The entry is destroyed when vRtrMplsAdminGroupRowStatus is set to 'destroy'.

OBJECT-TYPE

The value of vRtrMplsAdminGroupName uniquely identifies the name of the administrative group within a virtual router instance.

OBJECT-TYPE

vRtrMplsAdminGroupRowStatus is used to create, delete or control entries in the vRtrMplsAdminGroupTable. To create a row entry, the row status should be set to 'createAndWait'. Before the row can be placed into the 'active' state, vRtrMplsAdminGroupValue must be set to a value between 0 and 31. To delete a row entry, the row status should be set to 'destroy'

OBJECT-TYPE

The value of vRtrMplsAdminGroupValue specifies the group value associated with this administrative group. This value is unique within a virtual router instance. A value of -1 indicates that the group value for this entry has not been set.

OBJECT-TYPE

The vRtrMplsFSGroupTable has an entry for each group that is a part of the fate sharing database configured for the virtual router in the system. A fate sharing group is used to define a group of links and nodes in the network that share common risk attributes. To minimize a single point of failure, backup paths can be created that not only avoid the nodes and links of the primary path but also any other nodes and links that share risk with the nodes and links of the primary path.

OBJECT-TYPE

Each row entry in the vRtrMplsFSGroupTable represents a fate sharing group which is a database of nodes and links that share common risk attributes. Entries in this table are created and deleted via SNMP SET operations. An entry is created by setting the value of vRtrMplsFSGroupRowStatus to 'createAndGo'. An entry can be deleted by setting vRtrMplsFSGroupRowStatus to 'destroy'.

OBJECT-TYPE

The value of vRtrMplsFSGroupName uniquely identifies the name of the fate sharing group within a virtual router instance.

OBJECT-TYPE

vRtrMplsFSGroupRowStatus is used to create, delete or control entries in the vRtrMplsFSGroupTable. To create a row entry, the row status should be set to 'createAndGo'. To delete a row entry, the row status should be set to 'destroy'

OBJECT-TYPE

The value of vRtrMplsFSGroupCost specifies the cost assigned to the fate sharing group. This cost is applied to all nodes and links that are part of this group and used for CSPF calculations. The higher the cost of the node or link, the lesser its chance of being selected as part of the path.

OBJECT-TYPE

The vRtrMplsFSGroupParamsTable has an entry for each node or link that is part of a fate sharing group on this virtual router.

OBJECT-TYPE

Each row entry in the vRtrMplsFSGroupParamsTable represents either a node or a link that is a part of a fate sharing group defined in the vRtrMplsFSGroupTable. Entries in this table are created and deleted via SNMP SET operations. An entry is created by setting the value of vRtrMplsFSGroupParamsRowStatus to 'createAndGo'. An entry can be deleted by setting vRtrMplsFSGroupParamsRowStatus to 'destroy'. To configure a node to be part of the group, create an entry in this table with vRtrMplsFSGroupParamsFromAddr set to a valid non-zero IP address and vRtrMplsFSGroupParamsToAddr set to 0. To configure a link to be part of the group, create an entry in this table with both vRtrMplsFSGroupParamsFromAddr and vRtrMplsFSGroupParamsToAddr set to valid non-zero IP addresses.

OBJECT-TYPE

The value of vRtrMplsFSGroupParamsFromAddr along with the value of vRtrMplsFSGroupParamsToAddr uniquely identifies a link or node within a fate sharing group. This value must be non-zero for all row entries whether it represents a node or a link.

OBJECT-TYPE

The value of vRtrMplsFSGroupParamsToAddr along with the value of vRtrMplsFSGroupParamsFromAddr uniquely identifies a link or node within a fate sharing group. This value must be 0 for row entries that represent a node and must be non-zero for row entries that represent a link.

OBJECT-TYPE

vRtrMplsFSGroupParamsRowStatus is used to create, delete or control entries in the vRtrMplsFSGroupParamsTable. To create a row entry, the row status should be set to 'createAndGo'. To delete a row entry, the row status should be set to 'destroy'

OBJECT-IDENTITY

OBJECT-TYPE

Used by vRtrMplsLspDown, the value indicates the reason for the LSP going down.

OBJECT-TYPE

Used by vRtrMplsLspPathDown, the value indicates the reason for the LSP path going down.

OBJECT-TYPE

used by Nokia SROS series MPLS Configuration change Notifications, the object ID indicates the MPLS table and entry.

OBJECT-TYPE

The unique value which identifies this Point to Multipoint Labeled Switch Path (P2MP LSP) for this virtual router in the Nokia SROS system. It is a unique value among entries with the same value of vRtrID.

OBJECT-TYPE

Used by vRtrMplsP2mpInstanceDown, the value indicates the reason for the P2MP instance going down.

OBJECT-TYPE

The value of vRtrMplsS2lSubLspNtDstAddrType indicates the type of vRtrMplsS2lSubLspNtDstAddr.

OBJECT-TYPE

The value of vRtrMplsS2lSubLspNtDstAddr indicates the IP address of the destination address of the S2L sub LSP.

OBJECT-TYPE

The value of vRtrMplsLspPathCongChgPercent indicates the percentage change in congestion.

OBJECT-TYPE

The value of vRtrMplsLspPathMbbStatus indicates the status of the make-before-break (MBB) operation for the LSP path.

OBJECT-TYPE

The value of vRtrMplsLspPathMbbReasonCode indicates the reason code for the make-before-break (MBB) operation of the LSP path. It indicates whether the operation is failed, aborted or ignored.

OBJECT-TYPE

The value of vRtrMplsLspSwitchStbyReasonCode indicates the reason for the failure of switch to a new standby path from the current active standby path.

OBJECT-TYPE

The value of vRtrMplsLspOldTunnelIndex indicates the tunnel index of of the old LSP path.

OBJECT-TYPE

The value of vRtrMplsXCNotifRednIndicesBitMap indicates the RSVP sessions that either changed state and retained the changed state for the entire quiet interval of 2 minutes or the RSVP sessions that changed state during multiple intervals until a maximum interval of 10 minutes has elapsed. Each bit location in vRtrMplsXCNotifRednIndicesBitMap corresponds to a created or deleted row entry in vRtrMplsXCTable as identified by the value of vRtrMplsXCIndex. This index is same as the value of TIMETRA-RSVP-MIB::vRtrRsvpSessionIndex which corresponds to a created or deleted RSVP session entry in TIMETRA-RSVP-MIB::vRtrRsvpSessionTable. The value of vRtrMplsXCNotifyRednStartIndex indicates the index value of the first affected row entry represented by bit 0, the most significant bit. If the value of vRtrMplsXCNotifyRednBundlingType is set to 'create (2)', all the bits set in vRtrMplsXCNotifRednIndicesBitMap represent created RSVP sessions. If the value of vRtrMplsXCNotifyRednBundlingType is set to 'delete (1)', all the bits set in vRtrMplsXCNotifRednIndicesBitMap represent deleted RSVP sessions.

OBJECT-TYPE

The value of vRtrMplsXCNotifyRednBundlingType indicates whether this notification is generated for deletion or creation of RSVP sessions on this ingress, transit or egress router instance.

OBJECT-TYPE

The value of vRtrMplsXCNotifyRednNumOfBitsSet indicates the total number of bits set in vRtrMplsXCNotifRednIndicesBitMap.

OBJECT-TYPE

The value of vRtrMplsXCNotifyRednStartIndex indicates which vRtrMplsXCIndex is represented by the first bit in vRtrMplsXCNotifRednIndicesBitMap.

OBJECT-TYPE

The value of vRtrMplsXCNotifyRednEndIndex indicates which vRtrMplsXCIndex is represented by the last bit in vRtrMplsXCNotifRednIndicesBitMap. The value vRtrMplsXCNotifyRednEndIndex can be useful for a sanity check of vRtrMplsXCNotifyRednNumOfBitsSet. vRtrMplsXCNotifyRednNumOfBitsSet. = (vRtrMplsXCNotifyRednEndIndex - vRtrMplsXCNotifyRednStartIndex + 1).

OBJECT-TYPE

The value of vRtrMplsIgpOverloadRtrAddrType indicates the address type of vRtrMplsIgpOverloadRtrAddr.

OBJECT-TYPE

The value of vRtrMplsIgpOverloadRtrAddr indicates the IP address of the router that is in IGP overload state.

OBJECT-TYPE

The value of vRtrMplsIgpOverloadIgpType indicates IGP which is notifying MPLS that a node is in the overload state.

OBJECT-TYPE

The value of vRtrMplsResourceType indicates various CPM/IOM resource used by MPLS.

OBJECT-TYPE

The vRtrMplsLabelRangeTable has an entry for each type of label, the minimum and maximum value in the label range and information on total available and aging labels in each range. This is a read-only table.

OBJECT-TYPE

Each row entry in the vRtrMplsLabelRangeTable represents a type of label. Each entry contains the label range used by that label type and the number of aging and allocated labels in the range.

OBJECT-TYPE

The value of vRtrMplsLabelType specifies the type of label and is the index for this table.

OBJECT-TYPE

The value of vRtrMplsLabelRangeMin indicates the minimum label value in the range for a particular label type.

OBJECT-TYPE

The value of vRtrMplsLabelRangeMax indicates the maximum label value in the range for a particular label type.

OBJECT-TYPE

The value of vRtrMplsLabelRangeAging represents the number of labels that are currently allocated and aging.

OBJECT-TYPE

The value of vRtrMplsLabelRangeAvailable represents the number of labels that are currently available for each label type.

OBJECT-TYPE

The vRtrMplsStaticLSPLabelTable has an entry for each allocated label that is part of the static LSP label range. This is a read-only table.

OBJECT-TYPE

Each row entry in the vRtrMplsStaticLSPLabelTable represents a label of type static LSP that is currently allocated. The entry includes information about the current owner for that label.

OBJECT-TYPE

The value of vRtrMplsStaticLSPLabel specifies the label value for a static LSP. The range of vRtrMplsStaticLSPLabel is dynamic and depends on the value of vRtrMplsLabelStaticLabelRange. The normal range of vRtrMplsStaticLSPLabel starts at 32 and ends at the value of vRtrMplsLabelStaticLabelRange + 32.

OBJECT-TYPE

The value of vRtrMplsStaticLSPLabelOwner indicates the owner for the label value vRtrMplsStaticLSPLabel.

OBJECT-TYPE

The vRtrMplsStaticSvcLabelTable has an entry for each allocated label that is part of the static service label range. This is a read-only table.

OBJECT-TYPE

Each row entry in the vRtrMplsStaticSvcLabelTable represents a label of type static-svc that is currently allocated. The entry includes information about the current owner for that label.

OBJECT-TYPE

The value of vRtrMplsStaticSvcLabel specifies the label value for a static SVC. The range of vRtrMplsStaticSvcLabel is dynamic and depends on the value of vRtrMplsLabelStaticLabelRange. The range for vRtrMplsStaticSvcLabel starts at 32 and ends at 32 + vRtrMplsLabelStaticLabelRange.

OBJECT-TYPE

The value of vRtrMplsStaticSvcLabelOwner specifies the owner for the label value vRtrMplsStaticSvcLabel.

OBJECT-TYPE

The value of vRtrMplsSrlgGrpTableLastChanged indicates the sysUpTime at the time of the last modification to vRtrMplsSrlgGrpTable by adding, deleting an entry or change to a writable object in the table. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The vRtrMplsSrlgGrpTable has an entry for each Shared Risk Link Groups (SRLG) group configured for MPLS in the system.

OBJECT-TYPE

Each row entry represents a SRLG group on this virtual router that participates in the MPLS protocol. A row can be created or deleted via SNMP SET requests.

OBJECT-TYPE

The value of vRtrMplsSrlgGrpName indicates the SRLG group name.

OBJECT-TYPE

vRtrMplsSrlgGrpRowStatus is used to create, delete or control entries in the vRtrMplsSrlgGrpTable. A value must also be set for vRtrMplsSrlgGrpValue before the row entry can transition to the 'active' state.

OBJECT-TYPE

The value of vRtrMplsSrlgGrpLastChanged indicates the timestamp of last change to this row in vRtrMplsSrlgGrpTable.

OBJECT-TYPE

The value of vRtrMplsSrlgGrpValue specifies the group value associated with vRtrMplsSrlgGrpName. This value is unique within a virtual router instance. At the time of row creation, a value for vRtrMplsSrlgGrpValue must be specified or else row creation would fail.

OBJECT-TYPE

The value of vRtrMplsIfSrlgGrpTblLastChanged indicates the sysUpTime at the time of the last modification to vRtrMplsIfSrlgGrpTable by adding, deleting an entry or change to a writable object in the table. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The vRtrMplsIfSrlgGrpTable has an entry for each Shared Risk Link Group (SRLG) groups associated with a router interface configured for MPLS in the system.

OBJECT-TYPE

Each row entry represents an SRLG group associated with a interface on this virtual router that participates in the MPLS protocol. A row can be created or deleted via SNMP SET requests.

OBJECT-TYPE

The value of vRtrMplsIfSrlgGrpName indicates the SRLG group name.

OBJECT-TYPE

vRtrMplsIfSrlgGrpRowStatus is used to create, delete or control entries in the vRtrMplsIfSrlgGrpTable.

OBJECT-TYPE

The value of vRtrMplsIfSrlgGrpLastChanged indicates the timestamp of last change to this row in vRtrMplsIfSrlgGrpTable.

OBJECT-TYPE

The value of vRtrMplsP2mpInstTblLastChanged indicates the sysUpTime at the time of the last modification to vRtrMplsP2mpInstTable by adding, deleting an entry or change to a writable object in the table. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

vRtrMplsP2mpInstTable contains configuration information for the Mpls Point to Multipoint (P2MP) Instance on a virtual router.

OBJECT-TYPE

vRtrMplsP2mpInstEntry is an entry (conceptual row) in the vRtrMplsP2mpInstTable. Each entry represents the configuration for a Mpls Point to Multipoint (P2MP) Instance. Entries in this table can be created and deleted via SNMP SET operations.

OBJECT-TYPE

The unique value which identifies this Point to Multipoint Labeled Switch Path (P2MP LSP) for this virtual router in the Nokia SROS system. It is a unique value among entries with the same value of vRtrID.

OBJECT-TYPE

vRtrMplsP2mpInstRowStatus is used to create, delete or control entries in the vRtrMplsP2mpInstTable.

OBJECT-TYPE

The value of vRtrMplsP2mpInstLastChange indicates the timestamp of last change to this row in vRtrMplsP2mpInstTable.

OBJECT-TYPE

The value of vRtrMplsP2mpInstName specifies the administrative name for the P2MP instance which must be unique within a virtual router instance.

OBJECT-TYPE

The value of vRtrMplsP2mpInstType specifies the type of P2MP LSP instance.

OBJECT-TYPE

The value of vRtrMplsP2mpInstProperties indicates the set of configured properties for this path expressed as a bit map. For example, if the path is an adaptive path, the bit corresponding to bit value 1 is set.

OBJECT-TYPE

The value of vRtrMplsP2mpInstBandwidth specifies the amount of bandwidth in megabits per second (Mbps) to be reserved for the P2MP LSP.

OBJECT-TYPE

The value of vRtrMplsP2mpInstState indicates the current working state of this path within this P2MP LSP.

OBJECT-TYPE

The value of vRtrMplsP2mpInstSetupPriority indicates the setup priority to use when insufficient bandwidth is available to setup a P2MP LSP. The setup priority is compared against the hold priority of existing LSPs. If the setup priority is higher than the hold priority of the established LSPs, this P2MP LSP may preempt the other LSPs. A value of zero (0) is the highest priority and a value of seven (7) is the lowest priority. When the vRtrMplsP2mpInstHopLimit bit in vRtrMplsP2mpInstInheritance is cleared (0), the value returned to a GET request is inherited from vRtrMplsLspHopLimit.

OBJECT-TYPE

The value of vRtrMplsP2mpInstHoldPriority indicates the hold priority to use when insufficient bandwidth is available to setup a P2MP LSP. The setup priority is compared against the hold priority of existing LSPs. If the setup priority is higher than the hold priority of the established LSPs, this P2MP LSP may preempt the other LSPs. A value of zero (0) is the highest priority and a value of seven (7) is the lowest priority. When the vRtrMplsP2mpInstHopLimit bit in vRtrMplsP2mpInstInheritance is cleared (0), the value returned to a GET request is inherited from vRtrMplsLspHopLimit.

OBJECT-TYPE

The value of vRtrMplsP2mpInstRecord specifies whether recording of all hops that a P2MP LSP traverses is enabled. When the value of vRtrMplsP2mpInstRecord is 'true', recording of all the hops that a P2MP LSP traverses is enabled. When the value of vRtrMplsP2mpInstRecord is 'false, recording of all the hops that a P2MP LSP traverses is disabled.

OBJECT-TYPE

The value of vRtrMplsP2mpInstHopLimit specifies the maximum number of hops that a P2MP LSP will traverse including the ingress and egress ESRs. A P2MP LSP will not be setup if the hop limit is exceeded. When the vRtrMplsP2mpInstHopLimit bit in vRtrMplsP2mpInstInheritance is cleared (0), the value returned to a GET request is inherited from vRtrMplsLspHopLimit.

OBJECT-TYPE

The value of vRtrMplsP2mpInstAdminState specifies desired administrative state for this P2MP LSP.

OBJECT-TYPE

The value of vRtrMplsP2mpInstOperState indicates the current operational state of this P2MP LSP.

OBJECT-TYPE

The value of vRtrMplsP2mpInstInheritance specifies whether or not each writable object in this row inherits its value from its corresponding object in the vRtrMplsLspTable. This object controls whether to inherit the operational value of that associated object, or use the administrative value configured in this row. Non mask bits will always have value of zero, and any attempt to change the value will be silently discarded. This object is a bit-mask, with the following positions: vRtrMplsP2mpInstHopLimit 0x40 vRtrMplsP2mpInstAdminGrpInclude 0x200 vRtrMplsP2mpInstAdminGrpExclude 0x400 vRtrMplsP2mpInstAdaptive 0x800 When the bit for an object is set to one, then the object's administrative and operational value are whatever the DEFVAL or most recently SET value is. The corresponding mask bit will be changed to one when SNMP SET is performed on any of the inherited objects (vRtrMplsP2mpInstHopLimit, vRtrMplsP2mpInstAdminGrpInclude, etc). When the bit for an object is set to zero, then the object's administrative and operational value are inherited from the corresponding object in vRtrMplsLspTable.

OBJECT-TYPE

The value of vRtrMplsP2mpInstLspId indicates the value which identifies the label switched path that is signaled for this entry.

OBJECT-TYPE

The value of vRtrMplsP2mpInstNegotiatedMTU indicates the size for the Maximum transmission unit (MTU) that is negotiated during establishment of this P2MP LSP path.

OBJECT-TYPE

The value of vRtrMplsP2mpInstFailCode indicates the reason code for P2MP LSP Path failure. A value of 0 indicates that no failure has occurred.

OBJECT-TYPE

The value of vRtrMplsP2mpInstFailNodeArType indicates the type of vRtrMplsP2mpInstFailNodeAddr. When no failure has occurred, vRtrMplsP2mpInstFailNodeArType is 0.

OBJECT-TYPE

The value of vRtrMplsP2mpInstFailNodeAddr indicates the IP address of the node in the P2MP LSP path at which the P2MP LSP path failed.

OBJECT-TYPE

The value of vRtrMplsP2mpInstAdminGrpInclude is a bit-map that specifies a list of admin groups that should be included when this P2MP LSP is setup. If bit 'n' is set, then the admin group with value 'n' is included for this P2MP LSP. This implies that each link that this P2MP LSP goes through must be associated with at least one of the admin groups in the include list. By default, all admin groups are in the include list.

OBJECT-TYPE

The value of vRtrMplsP2mpInstAdminGrpExclude is a bit-map that specifies a list of admin groups that should be excluded when this P2MP LSP is setup. If bit 'n' is set, then the admin group with value 'n' is excluded for this P2MP LSP. This implies that each link that this P2MP LSP goes through must not be associated with any of the admin groups in the exclude list. By default, no admin groups are in the exclude list.

OBJECT-TYPE

The value of vRtrMplsP2mpInstAdaptive specifies whether make-before-break functionality is enabled. If the value of vRtrMplsP2mpInstAdaptive is set to 'true', it enables make-before-break functionality for the P2MP LSP. When the attributes of an already established P2MP LSP are changed, either through manual configuration or due to a change in network topology, make-before-break functionality ensures that the resources of the existing P2MP LSP will not be released until a new path (with the same P2MP LSP Id) has been established and traffic flowing over the existing path is seamlessly transferred to the new path. If the value of vRtrMplsP2mpInstAdaptive is set to 'false', it disables make-before-break functionality.

OBJECT-TYPE

The value of vRtrMplsP2mpInstOperBandwidth indicates the amount of bandwidth in megabits per seconds (Mbps) that has been reserved for the operational P2MP LSP path. When make-before-break functionality for the P2MP LSP is enabled and if the path bandwidth is changed, the resources allocated to the existing P2MP LSP paths will not be released until a new path with the new bandwidth settings has been established. While a new path is being signaled, the administrative value and the operational values of the path bandwidth may differ. The value of vRtrMplsP2mpInstBandwidth specifies the bandwidth requirements for the new P2MP LSP path trying to be established whereas the value of vRtrMplsP2mpInstOperBandwidth specifies the bandwidth reserved for the existing P2MP LSP path.

OBJECT-TYPE

Setting the value of vRtrMplsP2mpInstResignal to 'doAction' triggers the resignaling of the P2MP LSP path. If the P2MP LSP path is operationally down either due to network failure or due to the retry attempts count being exceeded, setting this variable to 'doAction' will initiate the signaling for the path. A make-before-break signaling for the path will be initiated if the P2MP LSP is operationally up but the make-before-break retry attempts count was exceeded. Make-before-break signaling will also be initiated for any P2MP LSP that is operationally up. This may be used to cause a loose-hop P2MP LSP to be optimized. If a resignal is triggered while a resignaling is already in progress, the old transient state will be destroyed and a new transaction being triggered. An SNMP GET request on this object should return 'notApplicable'.

OBJECT-TYPE

The value of vRtrMplsP2mpInstOperMTU indicates the size for the Maximum transmission unit (MTU) that is currently in operation for this P2MP LSP Path.

OBJECT-TYPE

The value of vRtrMplsP2mpInstRecordLabel specifies when the value of vRtrMplsP2mpInstRecordLabel is 'record', recording of labels at each node that a P2MP LSP traverses is enabled. When the value of vRtrMplsP2mpInstRecordLabel is 'noRecord', recording of labels at each node that a P2MP LSP traverses is disabled.

OBJECT-TYPE

The value of vRtrMplsP2mpInstLastResigAttpt indicates the sysUpTime when the last attempt to resignal this P2MP LSP was made.

OBJECT-TYPE

The value of vRtrMplsP2mpInstMetric indicates the cost of the traffic engineered path returned by the IGP.

OBJECT-TYPE

The value of vRtrMplsP2mpInstLastMBBType indicates the type of last Make-before-break (MBB). If 'none', then no MBB has been attempted.

OBJECT-TYPE

The value of vRtrMplsP2mpInstLastMBBEnd indicates the sysUpTime when the last MBB ended.

OBJECT-TYPE

The value of vRtrMplsP2mpInstLastMBBMetric indicates the cost of the traffic engineered path for the P2MP LSP path prior to MBB.

OBJECT-TYPE

The value of vRtrMplsP2mpInstLastMBBState indicates whether the last Make-before-break was successful or failed. Possible states are: none (1) - no make-before-break invoked success (2) - make-before-break successful fail (3) - make-before-break failed.

OBJECT-TYPE

The value of vRtrMplsP2mpInstMBBTypeInProg indicates the type of the Make-before-break (MBB) that is in progress. If 'none', then no MBB is in progress.

OBJECT-TYPE

The value of vRtrMplsP2mpInstMBBStarted indicates the sysUpTime when the in-progress MBB started.

OBJECT-TYPE

The value of vRtrMplsP2mpInstMBBNextRetry indicates the amount of time remaining in seconds before the next attempt is made to retry the in-progress MBB.

OBJECT-TYPE

The value of vRtrMplsP2mpInstMBBRetryAttpts indicates 'n' where nth attempt for the MBB is in progress.

OBJECT-TYPE

The value of vRtrMplsP2mpInstMBBFailCode indicates the reason code for in-progress MBB failure. A value of 'none' indicates that no failure has occurred.

OBJECT-TYPE

The value of vRtrMplsP2mpInstMBBFailNodeType indicates the type of vRtrMplsP2mpInstMBBFailNodeAddr. A value of 'unknown' indicates that no failure has occurred.

OBJECT-TYPE

The value of vRtrMplsP2mpInstMBBFailNodeAddr indicates the IP address of the node in the P2MP LSP path at which the in-progress MBB failed. A value of 'unknown' for vRtrMplsP2mpInstMBBFailNodeType and empty string for vRtrMplsP2mpInstMBBFailNodeAddr indicates that no failure has occurred.

OBJECT-TYPE

The vRtrMplsP2mpInstStatTable has an entry for each Labeled Switch Path (LSP) configured for a virtual router in the system.

OBJECT-TYPE

Each row entry represents a collection of statistics for a P2MP Labeled Switch Path (LSP) configured for a virtual router in the system. Entries cannot be created and deleted via SNMP SET operations.

OBJECT-TYPE

The value of vRtrMplsP2mpInstStatS2lChanges indicates the number of S2l changes this P2MP LSP has had. For every S2l change (S2l down, S2l up, S2l change), a corresponding syslog/trap (if enabled) is generated for it.

OBJECT-TYPE

The value of vRtrMplsP2mpInstStatLastS2lChange indicates the time since the last change occurred on this P2MP LSP.

OBJECT-TYPE

The value of vRtrMplsP2mpInstStatConfiguredS2ls indicates the number of S2ls configured for this P2MP LSP.

OBJECT-TYPE

The value of vRtrMplsP2mpInstStatOperationalS2ls indicates the number of operational S2ls for this P2MP LSP. This includes the S2ls currently active.

OBJECT-TYPE

The value of vRtrMplsP2mpInstStatLastS2lTimeUp indicates the total time that this S2l has been operational.

OBJECT-TYPE

The value of vRtrMplsP2mpInstStatLastS2lTimeDown indicates the total time that this S2l has not been operational.

OBJECT-TYPE

The value of vRtrMplsP2mpInstStatTimeUp indicates the total time that this P2MP instance has been operational.

OBJECT-TYPE

The value of vRtrMplsP2mpInstStatTimeDown indicates the total time that this P2MP instance has not been operational.

OBJECT-TYPE

The The value of vRtrMplsP2mpInstStatTransitions indicates the number of state transitions (up -> down and down -> up) this P2mp instance has undergone.

OBJECT-TYPE

The value of vRtrMplsP2mpInstStatLastTrans indicates the time since the last transition occurred on this P2mp instance.

OBJECT-TYPE

The value of vRtrMplsS2lSubLspTblLastChanged indicates the sysUpTime at the time of the last modification to vRtrMplsS2lSubLspTable by adding, deleting an entry or change to a writable object in the table. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The vRtrMplsS2lSubLspTable provides an association between an P2MP LSP and a source to leaf (S2L) sub LSP path called as S2L here. A P2MP LSP can have more than one S2L sub LSP association.

OBJECT-TYPE

Each row entry represents an association between a Labeled Switch Path (P2MP LSP) in the vRtrMplsP2mpInstTable and a S2L sub LSP entry in the vRtrMplsS2lSubLspTable. Entries in this table can be created and deleted via SNMP SET operations. Setting RowStatus to 'active' requires vRtrMplsS2lSubLspType to have been assigned a valid value.

OBJECT-TYPE

The value of vRtrMplsS2lSubLspDstAddrType indicates the type of vRtrMplsS2lSubLspDstAddr.

OBJECT-TYPE

The value of vRtrMplsS2lSubLspDstAddr indicates the IP address of the destination address of the S2L sub LSP.

OBJECT-TYPE

The value of vRtrMplsS2lSubLspRowStatus specifies row status used for creation, deletion, or control of vRtrMplsLspPathTable entries. Before the row can be placed into the 'active' state vRtrMplsS2lSubLspType must have been assigned a valid value.

OBJECT-TYPE

The value of vRtrMplsS2lSubLspLastChange indicates the sysUpTime when this row was last modified.

OBJECT-TYPE

The value of vRtrMplsS2lSubLspType indicates the value that represents the role this S2L sub LSP is taking within this P2MP LSP.

OBJECT-TYPE

The value of vRtrMplsS2lSubLspProperties indicates the set of configured properties. For example, if the S2L sub LSP is an adaptive S2L sub LSP, the bit corresponding to bit value 1 is set.

OBJECT-TYPE

The value of vRtrMplsS2lSubLspState indicates the current working state of this S2L sub LSP within this LSP.

OBJECT-TYPE

The value of vRtrMplsS2lSubLspAdminState specifies the desired administrative state for this P2MP S2L sub LSP.

OBJECT-TYPE

The value of vRtrMplsS2lSubLspOperState indicates the current operational state of this P2MP S2L sub LSP.

OBJECT-TYPE

The value of vRtrMplsS2lSubGroupId indicates the value which identifies the group for this entry.

OBJECT-TYPE

The value of vRtrMplsS2lSubLspId indicates the value which identifies the label switched path that is signaled for this entry.

OBJECT-TYPE

The value of vRtrMplsS2lSubLspRetryTimeRemain indicates the time to signal this S2L sub LSP.

OBJECT-TYPE

The value of vRtrMplsS2lSubLspTunARHopLtIndex indicates Primary index into the mplsTunnelARHopTable identifying a particular recorded hop list. A value of 0 implies that there is no recorded hop list associated with this P2MP LSP path.

OBJECT-TYPE

The value of vRtrMplsS2lSubLspNegotiatedMTU indicates the size for the Maximum transmission unit (MTU) that is negotiated during establishment of this P2MP LSP Path.

OBJECT-TYPE

The value of vRtrMplsS2lSubLspFailCode indicates the reason code for P2MP LSP Path failure. A value of 0 indicates that no failure has occurred.

OBJECT-TYPE

The value of vRtrMplsS2lSubLspFailNodeArType indicates type of vRtrMplsS2lSubLspFailNodeAddr. When no failure has occurred, this value is 0.

OBJECT-TYPE

The value of vRtrMplsS2lSubLspFailNodeAddr indicates the IP address of the node in the P2MP S2L sub LSP at which the P2MP S2L sub LSP failed.

OBJECT-TYPE

The value of vRtrMplsS2lSubLspOperBandwidth indicates the amount of bandwidth in megabits per seconds (Mbps) that has been reserved for the operational P2MP S2L sub LSP. When make-before-break functionality for the P2MP LSP is enabled and if the S2L sub LSP bandwidth is changed, the resources allocated to the existing P2MP LSP paths will not be released until a new S2L sub LSP with the new bandwidth settings has been established. While a new S2L sub LSP is being signaled, the administrative value and the operational values of the S2L sub LSP bandwidth may differ. The value of vRtrMplsS2lSubLspOperBandwidth specifies the bandwidth requirements for the new P2MP S2L sub LSP trying to be established whereas the value of vRtrMplsS2lSubLspOperBandwidth specifies the bandwidth reserved for the existing P2MP S2L sub LSP.

OBJECT-TYPE

The value of vRtrMplsS2lSubLspTunCRHopLtIndex indicates primary index into the vRtrMplsTunnelCHopTable identifying a particular computed hop list. A value of 0 implies that there is no computed hop list associated with this LSP path.

OBJECT-TYPE

The value of vRtrMplsS2lSubLspOperMTU indicates the size for the Maximum transmission unit (MTU) that is currently operation for this P2MP LSP Path.

OBJECT-TYPE

The value of vRtrMplsS2lSubLspLastResigAttpt indicates the sysUpTime when the last attempt to resignal this LSP was made.

OBJECT-TYPE

The value of vRtrMplsS2lSubLspLastMBBType indicates the type of last Make-before-break (MBB). If 'none', then no MBB has been attempted.

OBJECT-TYPE

The value of vRtrMplsS2lSubLspLastMBBEnd indicates the sysUpTime when the last MBB ended.

OBJECT-TYPE

The value of vRtrMplsS2lSubLspLastMBBMetric indicates the cost of the traffic engineered S2L sub LSP for the S2L sub LSP prior to MBB.

OBJECT-TYPE

The value of vRtrMplsS2lSubLspLastMBBState indicates whether the last Make-before-break was successful or failed. Possible states are: none (1) - no make-before-break invoked success (2) - make-before-break successful fail (3) - make-before-break failed.

OBJECT-TYPE

The value of vRtrMplsS2lSubLspMBBTypeInProg indicates the type of the Make-before-break (MBB) that is in progress. If 'none', then no MBB is in progress.

OBJECT-TYPE

The value of vRtrMplsS2lSubLspMBBStarted indicates the sysUpTime when the in-progress MBB started.

OBJECT-TYPE

The value of vRtrMplsS2lSubLspMBBNextRetry indicates the amount of time remaining in seconds before the next attempt is made to retry the in-progress MBB.

OBJECT-TYPE

The value of vRtrMplsS2lSubLspMBBRetryAttpts indicates 'n' where nth attempt for the MBB is in progress.

OBJECT-TYPE

The value of vRtrMplsS2lSubLspMBBFailCode indicates the reason code for in-progress MBB failure. A value of 'none' indicates that no failure has occurred.

OBJECT-TYPE

The value of vRtrMplsS2lSubLspMBBFailNodeType indicates the type of vRtrMplsS2lSubLspMBBFailNodeAddr. A value of 'unknown' indicates that no failure has occurred.

OBJECT-TYPE

The value of vRtrMplsS2lSubLspMBBFailNodeAddr indicates the IP address of the node in the S2L sub LSP at which the in-progress MBB failed. A value of 'unknown' for vRtrMplsS2lSubLspMBBFailNodeType and empty string for vRtrMplsS2lSubLspMBBFailNodeAddr indicates that no failure has occurred.

OBJECT-TYPE

The value of vRtrMplsS2lSubLspUpTime indicates the timestamp when the S2l came up.

OBJECT-TYPE

The value of vRtrMplsS2lSubLspDownTime indicates the timestamp when the S2l went down.

OBJECT-TYPE

The value of vRtrMplsS2lSubLspIsFastRetry indicates which retry timer is being referred to by vRtrMplsS2lSubLspRetryTimeRemain. When the value of vRtrMplsLspPathIsFastRetry is set to 'true', vRtrMplsLspPathRetryTimeRemaining is referring to the P2MP S2L path fast timer, vRtrMplsGenP2mpS2lFastRetry. When the value of vRtrMplsLspPathIsFastRetry is set to 'false', vRtrMplsS2lSubLspRetryTimeRemain is referring to the LSP retry timer, vRtrMplsLspRetryTimer.

OBJECT-TYPE

The value of vRtrMplsS2lSubLspTimeoutIn indicates the amount of time remaining, in seconds, for the S2L path state to time out after the initial PATH message has been sent. If the timer expires and the S2L path has not become operationally up, the S2L path is torn down and the retry timer is started to schedule a new retry cycle.

OBJECT-TYPE

The value of vRtrMplsS2lSubLspMBBTimeoutIn indicates the amount of time remaining, in seconds, for the in-progress S2L MBB path state to time out after the initial PATH message has been sent. If the timer expires and the in-progress S2L MBB path has not become operationally up, the S2L MBB path is torn down and the retry timer is started to schedule a new retry cycle.

OBJECT-TYPE

The value of vRtrMplsS2lSubLspInterArea indicates whether the LSP path is either inter-area or intra-area.

OBJECT-TYPE

The vRtrMplsS2lSubLspStatTable has an entry for each Labeled Switch Path (LSP) configured for a virtual router in the system.

OBJECT-TYPE

Each row entry represents a collection of statistics for a P2MP Source to Leaf (S2L) Sub Labeled Switch Path (LSP) configured for a i virtual router in the system. Entries cannot be created and deleted via SNMP SET operations.

OBJECT-TYPE

The value of vRtrMplsS2lSubLspTimeUp indicates the total time that this LSP S2l has been operational. For example, the percentage up time can be determined by computing (vRtrMplsS2lSubLspTimeUp/vRtrMplsLspAge * 100 %).

OBJECT-TYPE

The value of vRtrMplsS2lSubLspTimeDown indicates the total time that this LSP S2l has not been operational.

OBJECT-TYPE

The value of vRtrMplsS2lSubLspRetryAttempts indicates the number of unsuccessful attempts which have been made to signal this S2l. As soon as the S2l gets signalled, this is set to 0.

OBJECT-TYPE

The value of vRtrMplsS2lSubLspTransitionCount indicates the number of transitions that have occurred for this LSP.

OBJECT-TYPE

The value of vRtrMplsS2lSubLspCspfQueries indicates the number of CSPF queries that have been made for this LSP S2l.

OBJECT-TYPE

The value of vRtrMplsSrlgDBRtrIdTblLastChg indicates the sysUpTime at the time of the last modification to vRtrMplsSrlgDBRtrIdTable by adding, deleting an entry or change to a writable object in the table. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The vRtrMplsSrlgDBRtrIdTable has an entry for each router-id configured under user Shared Risk Link Group (SRLG) database. The user manually enters the SRLG membership information for any link in the network, into the user SRLG database.

OBJECT-TYPE

Each row entry represents a router ID under which interface entries would be configured for the SRLG database table. A row can be created or deleted via SNMP SET requests.

OBJECT-TYPE

The value of vRtrMplsSrlgDBRtrIdRouterID specifies a 32-bit integer uniquely identifying the router in the Autonomous System. By convention to ensure uniqueness, this may default to the value of one of the router's IPv4 host addresses, represented as a 32-bit unsigned integer, if IPv4 is configured on the router. The router-id can be either the local one or some remote router.

OBJECT-TYPE

vRtrMplsSrlgDBRtrIdRowStatus is used to create, delete or control entries in the vRtrMplsSrlgDBRtrIdTable.

OBJECT-TYPE

The value of vRtrMplsSrlgDBRtrIdAdminState specifies the desired administrative state for the router-id entry in the vRtrMplsSrlgDBRtrIdTable.

OBJECT-TYPE

The value of vRtrMplsSrlgDBRtrIdLastChanged indicates the timestamp of last change to this row in vRtrMplsSrlgDBRtrIdTable.

OBJECT-TYPE

The value of vRtrMplsSrlgDBIfTblLastChanged indicates the sysUpTime at the time of the last modification to vRtrMplsSrlgDBIfTable by adding, deleting an entry or change to a writable object in the table. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The vRtrMplsSrlgDBIfTable has an entry for each Shared Risk Link Group (SRLG) groups associated with a interface which is validated as part of a router ID in the routing table. The user manually enters the SRLG membership information for any link in the network, into the user SRLG database.

OBJECT-TYPE

Each row entry represents an SRLG group associated with a interface which is validated as part of a router ID in the routing table. A row can be created or deleted via SNMP SET requests.

OBJECT-TYPE

The value of vRtrMplsSrlgDBIfIntIpAddrType indicates the type of vRtrMplsSrlgDBIfIntIpAddr.

OBJECT-TYPE

The value of vRtrMplsSrlgDBIfIntIpAddr indicates the IP address of the interface.

OBJECT-TYPE

The value of vRtrMplsSrlgDBIfSrlgGroupName indicates the SRLG group name.

OBJECT-TYPE

vRtrMplsSrlgDBIfRowStatus is used to create, delete or control entries in the vRtrMplsSrlgDBIfTable.

OBJECT-TYPE

The value of vRtrMplsSrlgDBIfLastChanged indicates the timestamp of last change to this row in vRtrMplsSrlgDBIfTable.

OBJECT-TYPE

The vRtrMplsInSegmentTable augments the mplsInSegmentTable in the MPLS-LSR-MIB.

OBJECT-TYPE

A row entry in this table corresponds to a row entry in the mplsInSegmentTable and adds to the information contained in that table.

OBJECT-TYPE

The value of vRtrMplsInSegmentNumS2ls indicates number of S2Ls on the insegment.

OBJECT-TYPE

The vRtrMplsOutSegmentTable augments the mplsOutSegmentTable in the MPLS-LSR-MIB.

OBJECT-TYPE

A row entry in this table corresponds to a row entry in the mplsOutSegmentTable and adds to the information contained in that table.

OBJECT-TYPE

The value of vRtrMplsOutSegmentNumS2ls indicates number of S2Ls on the outsegment.

OBJECT-TYPE

Timestamp of the last change to the vRtrMplsLspStatsTable either from adding a row or removing a row.

OBJECT-TYPE

vRtrMplsLspStatsTable controls Statistics in the ess data path at the ingress Label Switched Path (LSP) for an Mpls-Lsp FEC.

OBJECT-TYPE

A row in this table represents information about the Statistics collection per MPLS LSP.

OBJECT-TYPE

The value of vRtrMplsLspStatsType indicates the type of statistics.

OBJECT-TYPE

The value of vRtrMplsLspStatsSenderAddrType indicates address type of vRtrMplsLspStatsSenderAddr.

OBJECT-TYPE

The value of vRtrMplsLspStatsSenderAddr indicates the sender address.

OBJECT-TYPE

The value of vRtrMplsLspStatsLspName indicates the lsp name. If vRtrMplsLspType is not 'meshP2p' or 'oneHopP2p', vRtrMplsLspStatsLspName can have a maximum of 32 characters.

OBJECT-TYPE

vRtrMplsLspStatsRowStatus is used for the creation or deletion of entries in the vRtrMplsLspStatsTable.

OBJECT-TYPE

The value of vRtrMplsLspStatsLastChanged indicates the time stamp of the last change to this row of this table.

OBJECT-TYPE

The value of vRtrMplsLspStatsCollectStats specifies whether to collect statistics for this prefix.

OBJECT-TYPE

The value of vRtrMplsLspStatsAccntingPolicy specifies the accounting policy to be used for this entry. A value of zero indicates that the default accounting policy should be used.

OBJECT-TYPE

The value of vRtrMplsLspStatsAdminState specifies whether egress statistics are enabled for this lsp.

OBJECT-TYPE

The vRtrMplsLspStatisticsTable has an entry for each Labeled Switch Path (LSP) configured for a virtual router in the system.

OBJECT-TYPE

Each row entry represents a collection of statistics for a Labeled Switch Path (LSP) configured for a virtual router in the system. Entries cannot be created and deleted via SNMP SET operations.

OBJECT-TYPE

The value of vRtrMplsInProfilePktsFc0 indicates the number of in profile packets received for Forwarding Class 0.

OBJECT-TYPE

The value of vRtrMplsInProfilePktsFc0Low32 indicates the lower 32 bits of the value of vRtrMplsInProfilePktsFc0.

OBJECT-TYPE

The value of vRtrMplsInProfilePktsFc0High32 indicates the higher 32 bits of the value of vRtrMplsInProfilePktsFc0.

OBJECT-TYPE

The value of vRtrMplsInProfilePktsFc1 indicates the number of in profile packets received for Forwarding Class 1.

OBJECT-TYPE

The value of vRtrMplsInProfilePktsFc1Low32 indicates the lower 32 bits of the value of vRtrMplsInProfilePktsFc1.

OBJECT-TYPE

The value of vRtrMplsInProfilePktsFc1High32 indicates the higher 32 bits of the value of vRtrMplsInProfilePktsFc1.

OBJECT-TYPE

The value of vRtrMplsInProfilePktsFc2 indicates the number of in profile packets received for Forwarding Class 2.

OBJECT-TYPE

The value of vRtrMplsInProfilePktsFc2Low32 indicates the lower 32 bits of the value of vRtrMplsInProfilePktsFc2.

OBJECT-TYPE

The value of vRtrMplsInProfilePktsFc2High32 indicates the higher 32 bits of the value of vRtrMplsInProfilePktsFc2.

OBJECT-TYPE

The value of vRtrMplsInProfilePktsFc3 indicates the number of in profile packets received for Forwarding Class 3.

OBJECT-TYPE

The value of vRtrMplsInProfilePktsFc3Low32 indicates the lower 32 bits of the value of vRtrMplsInProfilePktsFc3.

OBJECT-TYPE

The value of vRtrMplsInProfilePktsFc3High32 indicates the higher 32 bits of the value of vRtrMplsInProfilePktsFc3.

OBJECT-TYPE

The value of vRtrMplsInProfilePktsFc4 indicates the number of in profile packets received for Forwarding Class 4.

OBJECT-TYPE

The value of vRtrMplsInProfilePktsFc4Low32 indicates the lower 32 bits of the value of vRtrMplsInProfilePktsFc4.

OBJECT-TYPE

The value of vRtrMplsInProfilePktsFc4High32 indicates the higher 32 bits of the value of vRtrMplsInProfilePktsFc4.

OBJECT-TYPE

The value of vRtrMplsInProfilePktsFc5 indicates the number of in profile packets received for Forwarding Class 5.

OBJECT-TYPE

The value of vRtrMplsInProfilePktsFc5Low32 indicates the lower 32 bits of the value of vRtrMplsInProfilePktsFc5.

OBJECT-TYPE

The value of vRtrMplsInProfilePktsFc5High32 indicates the higher 32 bits of the value of vRtrMplsInProfilePktsFc5.

OBJECT-TYPE

The value of vRtrMplsInProfilePktsFc6 indicates the number of in profile packets received for Forwarding Class 6.

OBJECT-TYPE

The value of vRtrMplsInProfilePktsFc6Low32 indicates the lower 32 bits of the value of vRtrMplsInProfilePktsFc6.

OBJECT-TYPE

The value of vRtrMplsInProfilePktsFc6High32 indicates the higher 32 bits of the value of vRtrMplsInProfilePktsFc6.

OBJECT-TYPE

The value of vRtrMplsInProfilePktsFc7 indicates the number of in profile packets received for Forwarding Class 7.

OBJECT-TYPE

The value of vRtrMplsInProfilePktsFc7Low32 indicates the lower 32 bits of the value of vRtrMplsInProfilePktsFc7.

OBJECT-TYPE

The value of vRtrMplsInProfilePktsFc7High32 indicates the higher 32 bits of the value of vRtrMplsInProfilePktsFc7.

OBJECT-TYPE

The value of vRtrMplsInProfileOctetsFc0 indicates the number of in profile octets received for Forwarding Class 0.

OBJECT-TYPE

The value of vRtrMplsInProfileOctetsFc0Low32 indicates the lower 32 bits of the value of vRtrMplsInProfileOctetsFc0.

OBJECT-TYPE

The value of vRtrMplsInProfileOctetsFc0High32 indicates the higher 32 bits of the value of vRtrMplsInProfileOctetsFc0.

OBJECT-TYPE

The value of vRtrMplsInProfileOctetsFc1 indicates the number of in profile octets received for Forwarding Class 1.

OBJECT-TYPE

The value of vRtrMplsInProfileOctetsFc1Low32 indicates the lower 32 bits of the value of vRtrMplsInProfileOctetsFc1.

OBJECT-TYPE

The value of vRtrMplsInProfileOctetsFc1High32 indicates the higher 32 bits of the value of vRtrMplsInProfileOctetsFc1.

OBJECT-TYPE

The value of vRtrMplsInProfileOctetsFc2 indicates the number of in profile octets received for Forwarding Class 2.

OBJECT-TYPE

The value of vRtrMplsInProfileOctetsFc2Low32 indicates the lower 32 bits of the value of vRtrMplsInProfileOctetsFc2.

OBJECT-TYPE

The value of vRtrMplsInProfileOctetsFc2High32 indicates the higher 32 bits of the value of vRtrMplsInProfileOctetsFc2.

OBJECT-TYPE

The value of vRtrMplsInProfileOctetsFc3 indicates the number of in profile octets received for Forwarding Class 3.

OBJECT-TYPE

The value of vRtrMplsInProfileOctetsFc3Low32 indicates the lower 32 bits of the value of vRtrMplsInProfileOctetsFc3.

OBJECT-TYPE

The value of vRtrMplsInProfileOctetsFc3High32 indicates the higher 32 bits of the value of vRtrMplsInProfileOctetsFc3.

OBJECT-TYPE

The value of vRtrMplsInProfileOctetsFc4 indicates the number of in profile octets received for Forwarding Class 4.

OBJECT-TYPE

The value of vRtrMplsInProfileOctetsFc4Low32 indicates the lower 32 bits of the value of vRtrMplsInProfileOctetsFc4.

OBJECT-TYPE

The value of vRtrMplsInProfileOctetsFc4High32 indicates the higher 32 bits of the value of vRtrMplsInProfileOctetsFc4.

OBJECT-TYPE

The value of vRtrMplsInProfileOctetsFc5 indicates the number of in profile octets received for Forwarding Class 5.

OBJECT-TYPE

The value of vRtrMplsInProfileOctetsFc5Low32 indicates the lower 32 bits of the value of vRtrMplsInProfileOctetsFc5.

OBJECT-TYPE

The value of vRtrMplsInProfileOctetsFc5High32 indicates the higher 32 bits of the value of vRtrMplsInProfileOctetsFc5.

OBJECT-TYPE

The value of vRtrMplsInProfileOctetsFc6 indicates the number of in profile octets received for Forwarding Class 6.

OBJECT-TYPE

The value of vRtrMplsInProfileOctetsFc6Low32 indicates the lower 32 bits of the value of vRtrMplsInProfileOctetsFc6.

OBJECT-TYPE

The value of vRtrMplsInProfileOctetsFc6High32 indicates the higher 32 bits of the value of vRtrMplsInProfileOctetsFc6.

OBJECT-TYPE

The value of vRtrMplsInProfileOctetsFc7 indicates the number of in profile octets received for Forwarding Class 7.

OBJECT-TYPE

The value of vRtrMplsInProfileOctetsFc7Low32 indicates the lower 32 bits of the value of vRtrMplsInProfileOctetsFc7.

OBJECT-TYPE

The value of vRtrMplsInProfileOctetsFc7High32 indicates the higher 32 bits of the value of vRtrMplsInProfileOctetsFc7.

OBJECT-TYPE

The value of vRtrMplsOutOfProfPktsFc0 indicates the number of out of profile packets received for Forwarding Class 0.

OBJECT-TYPE

The value of vRtrMplsOutOfProfPktsFc0Low32 indicates the lower 32 bits of the value of vRtrMplsOutOfProfPktsFc0.

OBJECT-TYPE

The value of vRtrMplsOutOfProfPktsFc0High32 indicates the higher 32 bits of the value of vRtrMplsOutOfProfPktsFc0.

OBJECT-TYPE

The value of vRtrMplsOutOfProfPktsFc1 indicates the number of out of profile packets received for Forwarding Class 1.

OBJECT-TYPE

The value of vRtrMplsOutOfProfPktsFc1Low32 indicates the lower 32 bits of the value of vRtrMplsOutOfProfPktsFc1.

OBJECT-TYPE

The value of vRtrMplsOutOfProfPktsFc1High32 indicates the higher 32 bits of the value of vRtrMplsOutOfProfPktsFc1.

OBJECT-TYPE

The value of vRtrMplsOutOfProfPktsFc2 indicates the number of out of profile packets received for Forwarding Class 2.

OBJECT-TYPE

The value of vRtrMplsOutOfProfPktsFc2Low32 indicates the lower 32 bits of the value of vRtrMplsOutOfProfPktsFc2.

OBJECT-TYPE

The value of vRtrMplsOutOfProfPktsFc2High32 indicates the higher 32 bits of the value of vRtrMplsOutOfProfPktsFc2.

OBJECT-TYPE

The value of vRtrMplsOutOfProfPktsFc3 indicates the number of out of profile packets received for Forwarding Class 3.

OBJECT-TYPE

The value of vRtrMplsOutOfProfPktsFc3Low32 indicates the lower 32 bits of the value of vRtrMplsOutOfProfPktsFc3.

OBJECT-TYPE

The value of vRtrMplsOutOfProfPktsFc3High32 indicates the higher 32 bits of the value of vRtrMplsOutOfProfPktsFc3.

OBJECT-TYPE

The value of vRtrMplsOutOfProfPktsFc4 indicates the number of out of profile packets received for Forwarding Class 4.

OBJECT-TYPE

The value of vRtrMplsOutOfProfPktsFc4Low32 indicates the lower 32 bits of the value of vRtrMplsOutOfProfPktsFc4.

OBJECT-TYPE

The value of vRtrMplsOutOfProfPktsFc4High32 indicates the higher 32 bits of the value of vRtrMplsOutOfProfPktsFc4.

OBJECT-TYPE

The value of vRtrMplsOutOfProfPktsFc5 indicates the number of out of profile packets received for Forwarding Class 5.

OBJECT-TYPE

The value of vRtrMplsOutOfProfPktsFc5Low32 indicates the lower 32 bits of the value of vRtrMplsOutOfProfPktsFc5.

OBJECT-TYPE

The value of vRtrMplsOutOfProfPktsFc5High32 indicates the higher 32 bits of the value of vRtrMplsOutOfProfPktsFc5.

OBJECT-TYPE

The value of vRtrMplsOutOfProfPktsFc6 indicates the number of out of profile packets received for Forwarding Class 6.

OBJECT-TYPE

The value of vRtrMplsOutOfProfPktsFc6Low32 indicates the lower 32 bits of the value of vRtrMplsOutOfProfPktsFc6.

OBJECT-TYPE

The value of vRtrMplsOutOfProfPktsFc6High32 indicates the higher 32 bits of the value of vRtrMplsOutOfProfPktsFc6.

OBJECT-TYPE

The value of vRtrMplsOutOfProfPktsFc7 indicates the number of out of profile packets received for Forwarding Class 7.

OBJECT-TYPE

The value of vRtrMplsOutOfProfPktsFc7Low32 indicates the lower 32 bits of the value of vRtrMplsOutOfProfPktsFc7.

OBJECT-TYPE

The value of vRtrMplsOutOfProfPktsFc7High32 indicates the higher 32 bits of the value of vRtrMplsOutOfProfPktsFc7.

OBJECT-TYPE

The value of vRtrMplsOutOfProfOctetsFc0 indicates the number of out of profile octets received for Forwarding Class 0.

OBJECT-TYPE

The value of vRtrMplsOutOfProfOctetsFc0Low32 indicates the lower 32 bits of the value of vRtrMplsOutOfProfOctetsFc0.

OBJECT-TYPE

The value of vRtrMplsOutOfProfOctetsFc0High32 indicates the higher 32 bits of the value of vRtrMplsOutOfProfOctetsFc0.

OBJECT-TYPE

The value of vRtrMplsOutOfProfOctetsFc1 indicates the number of out of profile octets received for Forwarding Class 1.

OBJECT-TYPE

The value of vRtrMplsOutOfProfOctetsFc1Low32 indicates the lower 32 bits of the value of vRtrMplsOutOfProfOctetsFc1.

OBJECT-TYPE

The value of vRtrMplsOutOfProfOctetsFc1High32 indicates the higher 32 bits of the value of vRtrMplsOutOfProfOctetsFc1.

OBJECT-TYPE

The value of vRtrMplsOutOfProfOctetsFc2 indicates the number of out of profile octets received for Forwarding Class 2.

OBJECT-TYPE

The value of vRtrMplsOutOfProfOctetsFc2Low32 indicates the lower 32 bits of the value of vRtrMplsOutOfProfOctetsFc2.

OBJECT-TYPE

The value of vRtrMplsOutOfProfOctetsFc2High32 indicates the higher 32 bits of the value of vRtrMplsOutOfProfOctetsFc2.

OBJECT-TYPE

The value of vRtrMplsOutOfProfOctetsFc3 indicates the number of out of profile octets received for Forwarding Class 3.

OBJECT-TYPE

The value of vRtrMplsOutOfProfOctetsFc3Low32 indicates the lower 32 bits of the value of vRtrMplsOutOfProfOctetsFc3.

OBJECT-TYPE

The value of vRtrMplsOutOfProfOctetsFc3High32 indicates the higher 32 bits of the value of vRtrMplsOutOfProfOctetsFc3.

OBJECT-TYPE

The value of vRtrMplsOutOfProfOctetsFc4 indicates the number of out of profile octets received for Forwarding Class 4.

OBJECT-TYPE

The value of vRtrMplsOutOfProfOctetsFc4Low32 indicates the lower 32 bits of the value of vRtrMplsOutOfProfOctetsFc4.

OBJECT-TYPE

The value of vRtrMplsOutOfProfOctetsFc4High32 indicates the higher 32 bits of the value of vRtrMplsOutOfProfOctetsFc4.

OBJECT-TYPE

The value of vRtrMplsOutOfProfOctetsFc5 indicates the number of out of profile octets received for Forwarding Class 5.

OBJECT-TYPE

The value of vRtrMplsOutOfProfOctetsFc5Low32 indicates the lower 32 bits of the value of vRtrMplsOutOfProfOctetsFc5.

OBJECT-TYPE

The value of vRtrMplsOutOfProfOctetsFc5High32 indicates the higher 32 bits of the value of vRtrMplsOutOfProfOctetsFc5.

OBJECT-TYPE

The value of vRtrMplsOutOfProfOctetsFc6 indicates the number of out of profile octets received for Forwarding Class 6.

OBJECT-TYPE

The value of vRtrMplsOutOfProfOctetsFc6Low32 indicates the lower 32 bits of the value of vRtrMplsOutOfProfOctetsFc6.

OBJECT-TYPE

The value of vRtrMplsOutOfProfOctetsFc6High32 indicates the higher 32 bits of the value of vRtrMplsOutOfProfOctetsFc6.

OBJECT-TYPE

The value of vRtrMplsOutOfProfOctetsFc7 indicates the number of out of profile octets received for Forwarding Class 7.

OBJECT-TYPE

The value of vRtrMplsOutOfProfOctetsFc7Low32 indicates the lower 32 bits of the value of vRtrMplsOutOfProfOctetsFc7.

OBJECT-TYPE

The value of vRtrMplsOutOfProfOctetsFc7High32 indicates the higher 32 bits of the value of vRtrMplsOutOfProfOctetsFc7.

OBJECT-TYPE

The value of vRtrMplsLspStatsPSBMatch indicates if a path state block (PSB) match was made against this LSP name.

OBJECT-TYPE

The value of vRtrMplsLspStatsTpOnly indicates whether the statistics apply to mpls-tp lsp or for regular rsvp-te signalled terminating LSP. The value of 'true' indicates the statistics apply to mpls-tp LSP only. The value of 'false' indicates the statistics apply for regular rsvp-te signalled terminating LSP.

OBJECT-TYPE

The value of vRtrMplsLspStatsLspType indicates whether the statistics apply to MPLS-TP, P2P, P2MP, SR-TE, PCE-INIT SR-TE, Auto P2P, Auto SR-TE or Auto P2MP LSP. When the value of vRtrMplsLspStatsTpOnly is 'true', the statistics apply for MPLS-TP LSP only and vRtrMplsLspStatsLspType is set to 'tpLsp'. When the value of vRtrMplsLspStatsTpOnly is 'false', the statistics apply for regular RSVP-TE signalled terminating LSP and the value of vRtrMplsLspStatsLspType can be set to either p2p, p2mp, srTE, pceInitSrTe, autoP2p, autoSrTe or autoP2mp.

OBJECT-TYPE

The value of vRtrMplsLspAggregatePkts indicates the sum total of all in profile and out profile packets received for all Forwarding Classes.

OBJECT-TYPE

The value of vRtrMplsLspAggregateOctets indicates the sum total of all in profile and out profile octets received for all Forwarding Classes.

OBJECT-TYPE

The value of vRtrMplsLspTemplateTblLastChgd indicates the sysUpTime at the time of the last modification of an entry in the vRtrMplsLspTemplateTable. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The vRtrMplsLspTemplateTable has an entry for each Labeled Switch Path Template(LSP Template) configured for a virtual router in the system. The table contains a list of LSP Templates that are referenced when dynamic LSP creation is required.

OBJECT-TYPE

Each row entry represents a Labeled Switch Path Template (LSP Template) configured for a virtual router in the system. Entries in this table can be created and deleted via SNMP SET operations.

OBJECT-TYPE

The value of the object vRtrMplsLspTemplateName specifies the name of the LSP Template which is used as a guideline to create and signal multiple LSP instances when dynamic LSP creation is required.

OBJECT-TYPE

The value of vRtrMplsLspTemplateRowStatus specifies the Row Status for this entry.

OBJECT-TYPE

The value of vRtrMplsLspTemplateLastChanged indicates the timestamp of last change to this row in vRtrMplsLspTemplateTable.

OBJECT-TYPE

The value of vRtrMplsLspTemplateAdminState specifies the current administrative state of the LSP Template.

OBJECT-TYPE

The value of vRtrMplsLspTemplateType specifies the type of the LSP template. The value of vRtrMplsLspTemplateType means: 'p2mp (1)' - auto creation of P2MP LSPs. 'onehopP2P (2)' - auto creation of one-Hop P2P LSPs. 'meshP2P (3)' - auto creation of mesh P2P LSPs. 'onehopP2PSrTe (4)'- auto creation of one-Hop P2P SrTe LSPs. 'meshP2PSrTe (5)' - auto creation of mesh P2P SrTe LSPs. 'pceInitP2PSrTe (6)'- auto creation of PCE-Initiated P2P SR-Te LSPs.

OBJECT-TYPE

The value of vRtrMplsLspTemplateAdaptive specifies whether the make-before-break functionality is enabled for the LSPs that are dynamically created using this LSP template. When the value of vRtrMplsLspTemplateAdaptive is set to 'true', make-before-break functionality is enabled. When the value is set to 'false' make-before-break functionality is disabled.

OBJECT-TYPE

The value of vRtrMplsLspTemplateBandwidth specifies the amount of bandwidth in megabits per seconds (Mbps) to be reserved for the LSPs that are dynamically created using this LSP template. A value of zero (0) indicates that no bandwidth is reserved.

OBJECT-TYPE

The value of vRtrMplsLspTemplateCspf specifies whether the CSPF computation for constrained-path LSP is enabled for the LSPs that are dynamically created using this LSP template. When the value of vRtrMplsLspTemplateCspf is set to 'true', CSPF computation for constrained-path is enabled. When the value is set to 'false', CSPF computation for constrained-path is disabled.

OBJECT-TYPE

The value of vRtrMplsLspTemplateDefaultPath specifies the default path used to signal LSPs that are dynamically created using this LSP template. If a corresponding index does not exist in MPLS-TE-MIB::mplsTunnelTable, an 'inconsistentValue' error will be returned.

OBJECT-TYPE

The value of vRtrMplsLspTemplateAdmGrpIncl specifies a bit-map of admin groups that are included when the dynamically created LSPs using this template are setup . If bit 'n' is set, then the admin group with value 'n' is included. This implies that each link that the LSP goes through must be associated with at least one of the admin groups in the include list. By default, all admin groups are in the include list.

OBJECT-TYPE

The value of vRtrMplsLspTemplateAdmGrpExcl specifies a bit-map of admin groups that are excluded when the dynamically created LSPs using this template are setup. If bit 'n' is set, then the admin group with value 'n' is excluded. This implies that each link that the LSP goes through must not be associated with any of the admin groups in the exclude list. By default, no admin groups are in the exclude list.

OBJECT-TYPE

The value of vRtrMplsLspTemplateFastReroute specifies whether fast reroute is enabled for the LSPs that are dynamically created using this LSP template. When the value of vRtrMplsLspTemplateFastReroute is set to 'true', fast reroute is enabled for the LSP. When the value of vRtrMplsLspTemplateFastReroute is set to 'false', fast reroute is disabled.

OBJECT-TYPE

The value of vRtrMplsLspTemplateFRMethod specifies the fast reroute method used for the LSPs that are dynamically created using this LSP template. When the value of vRtrMplsLspTemplateFRMethod is set to 'oneToOneBackup', a backup LSP is established which will intersect the original LSP somewhere downstream of the point of link or node failure. For each LSP that is backed up, a separate backup LSP is established. When the value of vRtrMplsLspTemplateFRMethod is set to 'facilityBackup', Instead of creating a separate LSP for every LSP that is to be backed up, a single LSP is created which serves as a backup for a set of LSPs. For LSP templates of type P2MP, oneToOneBackup is not supported.

OBJECT-TYPE

The value of vRtrMplsLspTemplateFRHopLimit specifies the total number of hops a detour or backup LSP can take before merging back onto the main LSP path.

OBJECT-TYPE

The value of vRtrMplsLspTemplateHopLimit specifies the maximum number of hops that a dynamically created LSP will traverse including the ingress and egress ESRs. A LSP will not be set up if the hop limit is exceeded.

OBJECT-TYPE

The value of vRtrMplsLspTemplateRecord specifies whether the recording of all the hops is enabled for LSPs that are dynamically created using this template. When the value of vRtrMplsLspTemplateRecord is set to 'record', recording of all the hops that a LSP traverses is enabled. When the value of vRtrMplsLspTemplateRecord is set to 'noRecord', recording of all the hops that a LSP traverses is disabled.

OBJECT-TYPE

The value of vRtrMplsLspTemplateRecordLabel specifies whether the recording of labels is enabled for LSPs that are dynamically created using this LSP template . When the value of vRtrMplsLspTemplateRecordLabel is set to 'record', recording of labels at each node that a LSP traverses is enabled. When the value of vRtrMplsLspTemplateRecordLabel is set to 'noRecord', recording of labels at each node that a LSP traverses is disabled.

OBJECT-TYPE

The value of vRtrMplsLspTemplateRetryLimit specifies the maximum number of attempts made to establish an LSP that is dynamically created using this template. A value of zero(0) specifies that an infinite number of retry attempts should be made.

OBJECT-TYPE

The value of vRtrMplsLspTemplateRetryTimer specifies the time in seconds a dynamically created Lsp waits before it attempts to re-establish itself.

OBJECT-TYPE

The value of vRtrMplsLspTemplateCspfTeMetric specifies whether the TE metric is used for the purpose of the LSP path computation by CSPF (Constrained Shortest Path First). When the value of vRtrMplsLspTemplateCspfTeMetric is set to 'true', the TE metric is used to compute the path of the LSP by CSPF. When the value of vRtrMplsLspTemplateCspfTeMetric is set to 'false', IGP metric is used to compute the path of the LSP by CSPF.

OBJECT-TYPE

The value of vRtrMplsLspTemplateLspCount indicates the number of LSPs of type 'p2mpAuto' that are created using this template.

OBJECT-TYPE

The value of vRtrMplsLspTemplateMvpnRefCount indicates the number of MVPNs as well as number of P2MP LSP users associated to this template.

OBJECT-TYPE

The value of vRtrMplsLspTemplateFRPropAdmGrp specifies whether or not the use of administrative group constraints on a FRR backup LSP is enabled. If vRtrMplsLspTemplateFastReroute is set to 'true', the value of vRtrMplsLspTemplateFRPropAdmGrp specifies whether or not the administrative group constraints are signaled in the vRtrMplsLspTemplateFastReroute object. If vRtrMplsLspTemplateFastReroute is set to 'false', the value of vRtrMplsLspTemplateFRPropAdmGrp is insignificant.

OBJECT-TYPE

The value of vRtrMplsLspTemplatePropAdmGrp specifies whether the propagation of session attribute object with resource affinity (C-type 1) in PATH message is enabled for the LSPs that are dynamically created using this LSP template. By default, the value of vRtrMplsLspTemplatePropAdmGrp is 'false' which specifies the session attribute object without resource affinity (C-Type 7) is propagated in PATH message and the admin groups are ignored on Label Switched Router(LSR) while doing CSPF calculation.

OBJECT-TYPE

The value of vRtrMplsLspTemplateBgpShortcut specifies whether to exclude or include a RSVP LSP from being used as a shortcut while resolving BGP routes. When the value of vRtrMplsLspTemplateBgpShortcut is set to 'true' the RSVP LSP is used as a shortcut while resolving BGP routes. When the value of vRtrMplsLspTemplateBgpShortcut is set to 'false' the RSVP LSP is not used as a shortcut while resolving BGP routes.

OBJECT-TYPE

The value of vRtrMplsLspTemplateIgpShortcut specifies whether to exclude or include a RSVP LSP from being used as a shortcut while resolving IGP routes. When the value of vRtrMplsLspTemplateIgpShortcut is set to 'true' the RSVP LSP is used as a shortcut while resolving IGP routes. When the value of vRtrMplsLspTemplateIgpShortcut is set to 'false' the RSVP LSP is not used as a shortcut while resolving IGP routes.

OBJECT-TYPE

The value of vRtrMplsLspTemplateLdpOverRsvp specifies that this LSP can be included by IGP to calculate its SPF tree. The IGP (OSPF or ISIS) will subsequently provide LDP with all ECMP IGP next-hops and tunnel endpoints that it considers to be the lowest cost path to the destination. If an IGP calculation and an LDP over RSVP produce the same cost then LDP will always prefer an LDP over RSVP tunnel over an IGP route. By default, static and dynamic LSPs will be included when they are created. The default value for p2mp and bypass-only LSPs will be 'false'.

OBJECT-TYPE

The value of vRtrMplsLspTemplateLeastFill specifies whether the use of the least-fill path selection method for the computation of the path of this LSP template is enabled. By default, the path of an LSP is randomly chosen among a set of equal cost paths.

OBJECT-TYPE

The value of vRtrMplsLspTemplateMetric specifies the metric for this LSP which is used to select an LSP among a set of LSPs which are destined to the same egress 7x50 router. The LSP with the lowest metric will be selected. In LDP-over-RSVP, LDP performs a lookup in the Routing Table Manager (RTM) which provides the next hop to the destination PE and the advertising router (ABR or destination PE itself). If the advertising router matches the targeted LDP peer, LDP then performs a second lookup for the advertising router in the Tunnel Table Manager (TTM). This lookup returns the best RSVP LSP to use to forward packets for an LDP FEC learned through the targeted LDP session. The lookup returns the LSP with the lowest metric. If multiple LSPs have the same metric, then the result of the lookup will be to select the first one available in the TTM. A value of '0' indicates metric is not to be used.

OBJECT-TYPE

The value of vRtrMplsLspTemplateSetupPriority specifies the setup priority to use when insufficient bandwidth is available to setup a LSP. The setup priority is compared against the hold priority of existing LSPs. If the setup priority is higher than the hold priority of the established LSPs, this LSP may preempt the other LSPs. A value of zero (0) is the highest priority and a value of seven (7) is the lowest priority.

OBJECT-TYPE

The value of vRtrMplsLspTemplateHoldPriority specifies the hold priority to use when insufficient bandwidth is available to setup a LSP. The setup priority is compared against the hold priority of existing LSPs. If the setup priority is higher than the hold priority of the established LSPs, this LSP may preempt the other LSPs. A value of zero (0) is the highest priority and a value of seven (7) is the lowest priority.

OBJECT-TYPE

The value of vRtrMplsLspTemplateVprnAutoBind specifies whether the LSP can be used as part of the auto-bind feature for VPRN services. By default a LSP is available for inclusion to be used for the auto-bind feature. By default, static and dynamic LSPs will be included when they are created. The default value for p2mp and bypass-only LSPs will be 'false'.

OBJECT-TYPE

The value of vRtrMplsLspTempIgpSCutLfaType specifies whether to exclude or include a RSVP LSP from being used as a shortcut while resolving IGP routes in LFA SPF or whether to exclude or include a RSVP LSP from being used as a LFA SPF. When the value of vRtrMplsLspTempIgpSCutLfaType is set to 'lfaProtect' the RSVP LSP is used as a shortcut while resolving IGP routes in LFA SPF as well. When the value of vRtrMplsLspTempIgpSCutLfaType is set to 'lfaOnly' the RSVP LSP is used as a LFA SPF and not used as igp shortcut in regular SPF. An 'inconsistentValue' error is returned if an attempt is made to set this object to a non-default value when the value of the object vRtrMplsLspTemplateIgpShortcut is not set to 'true'.

OBJECT-TYPE

The value of vRtrMplsLspTempIgpSCutRelOffset specifies the the relative offset to the IGP metric on the SPF tree. The SPF tree is updated with the current IGP metric of the path between the endpoints of the LSP minus the value of vRtrMplsLspTempIgpSCutRelOffset. The default value of 2147483647 indicates the relative metric offset is not to be considered.

OBJECT-TYPE

The value of the vRtrMplsLspTempAutoBandwidth specifies whether automatic bandwidth adjustment has been enabled or disabled for this LSP template. A value of 'true' specifies that automatic bandwidth adjustment has been enabled for this LSP template and a value of 'false' specifies that automatic bandwidth adjustment has been disabled for this LSP template.

OBJECT-TYPE

The value of vRtrMplsLspTempFRNodeProtect specifies whether node protect has been enabled or disabled for this LSP template. A value of 'true' specifies that node protection i.e. protection against the failure of a node on the LSP template is enabled. A value of 'false' specifies that node protection is disabled.

OBJECT-TYPE

The value of vRtrMplsLspTemplateEgrStats specifies whether egress statistics has been enabled or disabled for this LSP template. A value of 'true' specifies egress statistics is enabled on this LSP template. A value of 'false' specifies that egress statistics is disabled on this LSP template.

OBJECT-TYPE

The value of vRtrMplsLspTempCollectStats specifies whether to collect statistics for this prefix.

OBJECT-TYPE

The value of vRtrMplsLspTempAccntingPolicy specifies the accounting policy to be used for this entry. A value of zero indicates that the default accounting policy should be used.

OBJECT-TYPE

The value of vRtrMplsLspTemplateFromAddrType specifies the IP address type of vRtrMplsLspTemplateFromAddr.

OBJECT-TYPE

The vRtrMplsLspTemplateFromAddr specifies the source address of this LSP template. The address type of vRtrMplsLspTemplateFromAddr is specified by vRtrMplsLspTemplateFromAddrType. When vRtrMplsLspTemplateFromAddr has not been explicitly set, the system IP address will be used.

OBJECT-TYPE

The value of vRtrMplsLspTemplateClassType specifies the class type (CT) associated with this LSP template.

OBJECT-TYPE

The value of vRtrMplsLspTempBkupClassType specifies the backup class type (CT) associated with this LSP template.

OBJECT-TYPE

The value of vRtrMplsLspTempBgpTransportTunn specifies whether an RSVP LSP is allowed or blocked in its usage as a transport LSP for BGP tunnel routes. When the value of vRtrMplsLspTempBgpTransportTunn is set to 'include' an RSVP LSP is allowed to be used as a transport LSP for BGP tunnel routes. When the value of vRtrMplsLspTempBgpTransportTunn is set to 'exclude' an RSVP LSP is not allowed to be used as a transport LSP for BGP tunnel routes.

OBJECT-TYPE

The value of vRtrMplsLspTempMainCTRetryLimit specifies the number of attempts the software should make before it can start using the backup class type.

OBJECT-TYPE

The value of vRtrMplsLspTemplateRsvpAdspec specifies whether or not the ADSPEC object will be included in RSVP messages. When the value of vRtrMplsLspTemplateRsvpAdspec is 'true', the ADSPEC object will be included in RSVP messages. When the value of vRtrMplsLspTemplateRsvpAdspec is 'false', the ADSPEC object will not be included in RSVP messages.

OBJECT-TYPE

The value of vRtrMplsLspTempLoadBalancingWt specifies the load balancing weight applied to this Labeled Switch Path(LSP) template. When a system level load-balancing command is enabled, packets forwarded to a set of ECMP tunnel next-hops will be sprayed using this weight configured for this LSP template.

OBJECT-TYPE

The value of vRtrMplsLspTempClassFwdEnabled specifies whether class based forwarding over this MPLS LSP template is enabled or not.

OBJECT-TYPE

The value of vRtrMplsLspTempFC specifies a set of forwarding classes configured for this LSP template expressed as a bit map. If a bit from 0 through 7 is set, then the corresponding forwarding class has been configured for this LSP template. If bit 8 is set, this LSP template has been designated as the default forwarding LSP.

OBJECT-TYPE

The value of vRtrMplsLspTempBfdTemplateName specifies the TIMETRA-BFD-MIB::tmnxBfdAdminTemplateName used by this LSP template.

OBJECT-TYPE

The value of vRtrMplsLspTempBfdEnable specifies whether BFD is enabled or not for this LSP template.

OBJECT-TYPE

The value of vRtrMplsLspTempBfdPingIntvl specifies the time interval for periodic LSP ping for BFD bootstrapping. The object vRtrMplsLspTempBfdPingIntvl is applicable to LSP templates with vRtrMplsLspTemplateType set to 'oneHopP2P' or 'meshP2P'. When the value of vRtrMplsLspTempBfdPingIntvl is set to '0', it disables LSP pings for BFD bootstrapping.

OBJECT-TYPE

The value of vRtrMplsLspTempEntropyLabel specifies whether the application takes into account the value of Entropy Label and Entropy Label Capability in the label stack for this LSP template. When the value of vRtrMplsLspTempEntropyLabel is set to 'enable', the application will account for EL/ELC in the label stack without taking into consideration the value of the enabled ELC. When the value of vRtrMplsLspTempEntropyLabel is set to 'force-disable' , the application will ignore the value of enabled ELC. When the value of vRtrMplsLspTempEntropyLabel is modified, Entropy Label will become operational when this LSP template is resignalled. By default, if this LSP template is of type RSVP-TE it will inherit the behavior as set by vRtrMplsGeneralEntropyLblRsvpTe, or if the LSP template is of type SR-TE it will inherit from vRtrMplsGeneralEntropyLblSrTe.

OBJECT-TYPE

The value of vRtrMplsLspTemplatePceReport specifies whether to override the global configuration of reporting of LSP Template to PCE. If the value of vRtrMplsLspTemplatePceReport is 'disabled' for an LSP Template either due to inheritance or due to LSP template level configuration, the value of vRtrMplsLspTemplatePceReport has no effect.

OBJECT-TYPE

The value of vRtrMplsLspTempMaxSrLabels specifies maximum segment routing label stack size for this LSP template. The default IXR platform is 3 and maximum value supported is 5.

OBJECT-TYPE

The value of vRtrMplsLspTempFrrOverheadLabel specifies maximum additional overhead labels for this LSP template.

OBJECT-TYPE

The value of vRtrMplsLspTempBfdFailureAction specifies the actions to be taken when this LSP template session fails. When vRtrMplsLspTempBfdFailureAction is set to down, it prevents the LSP template from being made available as a transport for any user. When vRtrMplsLspTempBfdFailureAction is set to failoverOrDown, and the BFD session associated with the active-path of a related LSP goes down, the LSP will switch to the standby-path if applicable. When the LSP cannot switchover, the LSP will go operationally down.

OBJECT-TYPE

The value of vRtrMplsLspTempCbfFwdingPlcy specifies the name of the Class Forwarding Policy for this LSP Template instance.

OBJECT-TYPE

The value of vRtrMplsLspTempCbfFwdingSet specifies the Class Forwarding Set ID for this LSP Template instance. If system profile is profile-b then valid range is 0..6 else 0..4

OBJECT-TYPE

The value of vRtrMplsLspTemplateId specifies the identifier for pce-init LSPs using this template are setup.

OBJECT-TYPE

The value of vRtrMplsLspTempPathCompMeth specifies LSP path computation method. If the value of vRtrMplsLspTempPathCompMeth is 'localCspf' for an LSP the path uses local CSPF. The default value for vRtrMplsLspTempPathCompMeth is 'none'.

OBJECT-TYPE

The value of vRtrMplsLspTempMetricType specifies metric type. If the value of vRtrMplsLspTempMetricType is 'igp', the metric used is IGP. If the value of vRtrMplsLspTempMetricType is 'te', the metric used is TE. The default value for vRtrMplsLspTempMetricType is 'igp'.

OBJECT-TYPE

The value of vRtrMplsLspTempLocalSrProt specifies the local SR protection. If the value of vRtrMplsLspTempLocalSrProt is 'none', there is no protection. If the value of vRtrMplsLspTempLocalSrProt is 'preferred', the protection is preferred. If the value of vRtrMplsLspTempLocalSrProt is 'mandatory', the protection is mandatory. The default value for vRtrMplsLspTempLocalSrProt is 'none'.

OBJECT-TYPE

The value of vRtrMplsLspTempLabelStackRed specifies whether label stack reduction is enabled.

OBJECT-TYPE

The value of vRtrMplsLspTempBfdUpWaitTimer specifies the time in seconds the software will wait for BFD to come up. The timer object is applicable only when vRtrMplsLspTempBfdFailureAction is set to 'failoverOrDown'. The timer object is applicable for LSP templates with vRtrMplsLspTemplateType set to 'oneHopP2PSrTe', 'meshP2PSrTe' or pceInitP2PSrte'. The timer is started when BFD is first enabled on a path or BFD transitions from up to down. When this timer expires and if BFD has not yet come up, the path is torn down by removing it from TTM and the IOM and the retry timer is started.

OBJECT-TYPE

The value of vRtrMplsLspTempSelfPing specifies whether to override the global configuration of Self Ping. If the value of vRtrMplsLspTempSelfPing is 'disabled' for an LSP template entry either due to inheritance or due to lsp template level configuration, the value of vRtrMplsLspTempSelfPing has no affect. The default value for vRtrMplsLspTempSelfPing is 'inherit'.

OBJECT-TYPE

The value of vRtrMplsLspAutoBWTableLastChg indicates the sysUpTime at the time of the last modification to vRtrMplsLspAutoBandwidthTable by adding, deleting an entry or change to a writable object in the table. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The vRtrMplsLspAutoBandwidthTable has an entry for auto bandwidth configuration for each Labeled Switch Path (LSP) configured for a virtual router in the system.

OBJECT-TYPE

Each row entry represents auto bandwidth configuration for a Labeled Switch Path (LSP) configured for a virtual router in the system.

OBJECT-TYPE

The value of vRtrMplsLspAutoBWLspName uniquely identifies a row in the vRtrMplsLspAutoBandwidthTable. If vRtrMplsLspType is not 'meshP2p' or 'oneHopP2p', vRtrMplsLspAutoBWLspName can have a maximum of 32 characters.

OBJECT-TYPE

The sysUpTime when this row was last modified.

OBJECT-TYPE

The value of vRtrMplsLspAutoBWAdjDNPercent specifies minimum difference between the current bandwidth reservation of the LSP and the (measured) maximum average data rate, expressed as a percentage of the current bandwidth, for decreasing the bandwidth of the LSP. At the adjust interval expiry, if the measured bandwidth falls below the current bandwidth by the value of vRtrMplsLspAutoBWAdjDNPercent it can cause a resignaling attempt for the LSP When the value of vRtrMplsLspAutoBWAdjDNPercent is 0 it means that this threshold check is always true for any measured bandwidth less than current bandwidth

OBJECT-TYPE

The value of vRtrMplsLspAutoBWAdjDNMbps specifies the minimum difference between the current bandwidth reservation of the LSP and the (measured) maximum average data rate, expressed as an absolute bandwidth (Mbps), for decreasing the bandwidth of the LSP.

OBJECT-TYPE

The value of vRtrMplsLspAutoBWAdjMultiplier specifies the number of collection intervals in the adjust interval. The default value is derived from vRtrMplsGeneralAutoBWDefAdjMul and vRtrMplsLspAutoBWAdjCount.

OBJECT-TYPE

The value of vRtrMplsLspAutoBWAdjUPPercent specifies minimum difference between the current bandwidth reservation of the LSP and the (measured) maximum average data rate, expressed as a percentage of the current bandwidth, for increasing the bandwidth of the LSP. At the adjust interval expiry, if the measured bandwidth exceeds the current bandwidth by the value of vRtrMplsLspAutoBWAdjUPPercent it can cause a resignaling attempt for the LSP When the value of vRtrMplsLspAutoBWAdjUPPercent is 0 it means that this threshold check is always true for any measured bandwidth greater than current bandwidth

OBJECT-TYPE

The value of vRtrMplsLspAutoBWAdjUPMbps specifies the minimum difference between the current bandwidth reservation of the LSP and the (measured) maximum average data rate, expressed as an absolute bandwidth (Mbps), for increasing the bandwidth of the LSP.

OBJECT-TYPE

The value of vRtrMplsLspAutoBWMaxBW specifies the maximum that auto-bandwidth allocation is allowed to request for a LSP.

OBJECT-TYPE

The value of vRtrMplsLspAutoBWMinBW specifies the minimum that auto-bandwidth allocation is allowed to request for a LSP.

OBJECT-TYPE

The value of vRtrMplsLspAutoBWMonitorBW specifies whether the collection and display of auto-bandwidth measurements is enabled or disabled for the LSP. When the value of vRtrMplsLspAutoBWMonitorBW is 'true' the collection and display of auto-bandwidth measurements is enabled and when the value is 'false' it is disabled.

OBJECT-TYPE

The value of vRtrMplsLspAutoBWOverFlow specifies number of overflow samples that triggers an overflow auto-bandwidth adjustment attempt.

OBJECT-TYPE

The value of vRtrMplsLspAutoBWOvrFlwThreshold specifies the minimum difference between the current bandwidth of the LSP and the sampled data rate, expressed as a percentage of the current bandwidth, for counting an overflow sample.

OBJECT-TYPE

The value of vRtrMplsLspAutoBWOvrFlwBW specifies the minimum difference between the current bandwidth of the LSP and the sampled data rate, expressed as an absolute bandwidth (Mbps), for counting an overflow sample.

OBJECT-TYPE

The value of vRtrMplsLspAutoBWSampMultiplier specifies the multiplier for collection intervals in a sample interval.

OBJECT-TYPE

The value of vRtrMplsLspAutoBWSampTime indicates the sample multiplier times the collection interval.

OBJECT-TYPE

The value of vRtrMplsLspAutoBWLastAdj indicates the system time for the last auto-bandwidth adjustment.

OBJECT-TYPE

The value of vRtrMplsLspAutoBWLastAdjCause indicates the cause for the last auto-bandwidth adjustment.

OBJECT-TYPE

The value of vRtrMplsLspAutoBWNextAdj indicates the system time when then adjust-timer will expire.

OBJECT-TYPE

The value of vRtrMplsLspAutoBWMaxAvgRate indicates the maximum average data rate in any sample interval of the current adjust interval.

OBJECT-TYPE

The value of vRtrMplsLspAutoBWLastAvgRate indicates the average data rate in the sample interval that ended most recently.

OBJECT-TYPE

For each writable object in this row that can be configured to inherit its value from the corresponding object in the vRtrMplsGeneralTable, there is bit within vRtrMplsLspAutoBWInheritance that controls whether to inherit the operational value of the object or use the administratively set value. This object is a bit-mask, with the following positions: vRtrMplsLspAutoBWAdjMultiplier 0x1 vRtrMplsLspAutoBWSampMultiplier 0x2 When the bit for an object is set to one, then the object's administrative and operational value are whatever the DEFVAL or most recently SET value is. When the bit for an object is set to zero, then the object's administrative and operational value are inherited from the corresponding object in vRtrMplsGeneralTable.

OBJECT-TYPE

The value of vRtrMplsLspAutoBWCurrentBW indicates the current bandwidth reserved along the primary path.

OBJECT-TYPE

The value of vRtrMplsLspAutoBWAdjTime indicates the adjust multiplier times the collection interval.

OBJECT-TYPE

The value of vRtrMplsLspAutoBWOvrFlwCount indicates the number of overflow samples since the last reset.

OBJECT-TYPE

The value of vRtrMplsLspAutoBWSampCount indicates the count in the sample interval.

OBJECT-TYPE

The value of vRtrMplsLspAutoBWAdjCount indicates the count in the adjust interval.

OBJECT-TYPE

The value of vRtrMplsLspAutoBWOperState indicates the operational status for the LSP.

OBJECT-TYPE

The value of vRtrMplsLspAutoBWSampInterval indicates the number of sample intervals.

OBJECT-TYPE

The value of vRtrMplsLspAutoBWBeWeight specifies the weight in percent for forwarding class 'BE' for the LSP.

OBJECT-TYPE

The value of vRtrMplsLspAutoBWL2Weight specifies the weight in percent for forwarding class 'L2' for the LSP.

OBJECT-TYPE

The value of vRtrMplsLspAutoBWAfWeight specifies the weight in percent for forwarding class 'AF' for the LSP.

OBJECT-TYPE

The value of vRtrMplsLspAutoBWL1Weight specifies the weight in percent for forwarding class 'L1' for the LSP.

OBJECT-TYPE

The value of vRtrMplsLspAutoBWH2Weight specifies the weight in percent for forwarding class 'H2' for the LSP.

OBJECT-TYPE

The value of vRtrMplsLspAutoBWEfWeight specifies the weight in percent for forwarding class 'EF' for the LSP.

OBJECT-TYPE

The value of vRtrMplsLspAutoBWH1Weight specifies the weight in percent for forwarding class 'H1' for the LSP.

OBJECT-TYPE

The value of vRtrMplsLspAutoBWNcWeight specifies the weight in percent for forwarding class 'NC' for the LSP.

OBJECT-TYPE

The value of vRtrMplsLspAutoBWUnderFlow specifies the number of underflow samples that triggers an underflow auto-bandwidth adjustment attempt.

OBJECT-TYPE

The value of vRtrMplsLspAutoBWUndFlwThreshold specifies the minimum difference between the current bandwidth of the LSP and the sampled data rate, expressed as a percentage of the current bandwidth, for counting an underflow sample.

OBJECT-TYPE

The value of vRtrMplsLspAutoBWUndFlwBW specifies the minimum difference between the current bandwidth of the LSP and the sampled data rate, expressed as an absolute bandwidth (Mbps), for counting an underflow sample.

OBJECT-TYPE

The value of vRtrMplsLspAutoBWUndFlwCount indicates the number of underflow samples since the last reset.

OBJECT-TYPE

The value of vRtrMplsLspAutoBWMaxUndFlwBw indicates the maximum sampled bandwidth in the most recent consecutive underflow samples.

OBJECT-TYPE

The value of vRtrMplsLspAutoBWUseLastAdjBW specifies whether use of last adjusted bandwidth is enabled or diabled. When the value is 'true' the use of last adjusted bandwidth is enabled, and LSP paths will be signalled with the last adjusted bandwidth of the LSP and not the configured bandwidth.

OBJECT-TYPE

The value of vRtrMplsLspAutoBWSecRetryLimit specifies the max number of retry attempts that will be made to signal the secondary path with the last adjusted bandwidth. After the number of retry attempts is exceeded, no more attempts will be made to resignal the secondary path and the path will remain operationally down. A value of zero(0) specifies that the retry limit is infinite. This variable is valid only if vRtrMplsLspAutoBWUseLastAdjBW is set to 'enabled'.

OBJECT-TYPE

The value of vRtrMplsLspAutoBWLastAdjBW indicates the last adjusted bandwidth for the LSP. A value of -1 indicates that this value is invalid

OBJECT-TYPE

The vRtrMplsLspPathOperTable has an entry for an association between a Labeled Switch Path (LSP) in the vRtrMplsLspTable and a path (or tunnel) entry in the mplsTunnelTable.

OBJECT-TYPE

Each row entry represents an operational status for an association between a Labeled Switch Path (LSP) in the vRtrMplsLspTable and a path (or tunnel) entry in the mplsTunnelTable. Entries cannot be created and deleted via SNMP SET operations. A row entry will have valid operational status info when vRtrMplsLspPathOperState is set to inService.

OBJECT-TYPE

The value of vRtrMplsLspPathOperSetupPriority indicates the setup priority used by the operational LSP path. When make-before-break functionality for the LSP is enabled and if the path setup priority is changed, the resources allocated to the existing LSP paths will not be released until a new path with the new setup priority settings has been established. While a new path is being signaled, the administrative value and the operational values of the path setup priority may differ. The value of vRtrMplsLspPathSetupPriority specifies the setup priority for the new LSP path trying to be established whereas the value of vRtrMplsLspPathOperSetupPriority specifies the setup priority for the existing LSP path.

OBJECT-TYPE

The value of vRtrMplsLspPathOperHoldPriority indicates the hold priority used by the operational LSP path. When make-before-break functionality for the LSP is enabled and if the path hold priority is changed, the resources allocated to the existing LSP paths will not be released until a new path with the new hold priority settings has been established. While a new path is being signaled, the administrative value and the operational values of the path hold priority may differ. The value of vRtrMplsLspPathHoldPriority specifies the hold priority for the new LSP path trying to be established whereas the value of vRtrMplsLspPathOperHoldPriority specifies the hold priority for the existing LSP path.

OBJECT-TYPE

The value of vRtrMplsLspPathOperRecord indicates whether the operational LSP path is recording or not recording all the traversed hops. When make-before-break functionality for the LSP is enabled and if the path hops recording setting is changed, the resources allocated to the existing LSP paths will not be released until a new path with the new settings has been established. While a new path is being signaled, the administrative value and the operational values of hops recording setting of the path may differ. The value of vRtrMplsLspPathRecord specifies the hops recording setting for the new LSP path trying to be established whereas the value of vRtrMplsLspPathOperRecord specifies the hops recording setting for the existing LSP path.

OBJECT-TYPE

The value of vRtrMplsLspPathOperRecordLabel indicates whether the currently operational LSP path is recording or not recording the label allocated at each traversed node. When make-before-break functionality for the LSP is enabled and if the path label recording setting is changed, the resources allocated to the existing LSP paths will not be released until a new path with the new settings has been established. While a new path is being signaled, the administrative value and the operational values of label recording setting of the path may differ. The value of vRtrMplsLspPathRecordLabel specifies the label recording setting for the new LSP path trying to be established whereas the value of vRtrMplsLspPathOperRecordLabel specifies the label recording setting for the existing LSP path.

OBJECT-TYPE

The value of vRtrMplsLspPathOperHopLimit indicates the maximum hops limit used by the currently operational LSP path. When make-before-break functionality for the LSP is enabled and if the hop limit is changed at either LSP or LSP path level, the resources allocated to the existing LSP paths will not be released until a new path with the new settings has been established. While a new path is being signaled, the administrative value and the operational values of the path hop limit may differ. The value of either vRtrMplsLspHopLimit or vRtrMplsLspPathHopLimit specifies the hop limit for the new LSP path trying to be established whereas the value of vRtrMplsLspPathOperHopLimit specifies the hop limit for the existing LSP path.

OBJECT-TYPE

The value of vRtrMplsLspPathOperAdminGrpIncl is a bit-map which indicates a list of admin groups included by the currently operational LSP path. When make-before-break functionality for the LSP is enabled and if the list of included admin groups is changed at either LSP or LSP path level, the resources allocated to the existing LSP paths will not be released until a new path with the new settings has been established. While a new path is being signaled, the administrative value and the operational values of the path may differ. The value of either vRtrMplsLspAdminGroupInclude or vRtrMplsLspPathAdminGroupInclude specifies the include admin groups bit-map for the new LSP path trying to be established whereas the value of vRtrMplsLspPathOperAdminGrpIncl specifies the include admin groups bit-map for the existing LSP path.

OBJECT-TYPE

The value of vRtrMplsLspPathOperAdminGrExcld is a bit-map which indicates a list of admin groups excluded by the currently operational LSP path. When make-before-break functionality for the LSP is enabled and if the list of excluded admin groups is changed at either LSP or LSP path level, the resources allocated to the existing LSP paths will not be released until a new path with the new settings has been established. While a new path is being signaled, the administrative value and the operational values of the path may differ. The value of either vRtrMplsLspAdminGroupExclude or vRtrMplsLspPathAdminGroupExclude specifies the exclude admin groups bit-map for the new LSP path trying to be established whereas the value of vRtrMplsLspPathOperAdminGrExcld specifies the exclude admin groups bit-map for the existing LSP path.

OBJECT-TYPE

The value of vRtrMplsLspPathOperCspf indicates whether the currently operational LSP path has used CSPF computation for constrained-path enabled or disabled. When make-before-break functionality for the LSP is enabled and if the LSP CSPF setting is changed, the resources allocated to the existing LSP paths will not be released until a new path with the new settings has been established. While a new path is being signaled, the administrative value and the operational values of the path may differ. The value of vRtrMplsLspCspf specifies the CSPF setting for the new LSP path trying to be established whereas the value of vRtrMplsLspPathOperCspf specifies the CSPF setting for the existing LSP path.

OBJECT-TYPE

The value of vRtrMplsLspPathOperCspfToFrstLs indicates whether the currently operational LSP path had CSPF to first loose hop enabled or disabled. When make-before-break functionality for the LSP is enabled and if the LSP CSPF to First Loose Hop setting is changed, the resources allocated to the existing LSP paths will not be released until a new path with the new settings has been established. While a new path is being signaled, the administrative value and the operational values of the path may differ. The value of vRtrMplsLspCspfToFirstLoose specifies the CSPF to First Loose Hop setting for the new LSP path trying to be established whereas the value of vRtrMplsLspPathOperCspfToFrstLs specifies the CSPF to First Loose Hop setting for the existing LSP path. This object was deprecated in the 11.0 release.

OBJECT-TYPE

The value of vRtrMplsLspPathOperLeastFill indicates whether the currently operational LSP path was computed with the least-fill path selection method. When make-before-break functionality for the LSP is enabled and if the LSP least-fill setting is changed, the resources allocated to the existing LSP paths will not be released until a new path with the new settings has been established. While a new path is being signaled, the administrative value and the operational values of the path may differ. The value of vRtrMplsLspLeastFill specifies the least-fill setting for the new LSP path trying to be established whereas the value of vRtrMplsLspPathOperLeastFill specifies the least-fill setting for the existing LSP path.

OBJECT-TYPE

The value of vRtrMplsLspPathOperRsvpAdspec indicates whether the currently operational LSP path has ADSPEC object included in RSVP messages or not. When make-before-break functionality for the LSP is enabled and if the LSP adspec setting is changed, the resources allocated to the existing LSP paths will not be released until a new path with the new settings has been established. While a new path is being signaled, the administrative value and the operational values of the path may differ. The value of vRtrMplsLspRsvpAdspec specifies the adspec setting for the new LSP path trying to be established whereas the value of vRtrMplsLspPathOperRsvpAdspec specifies the adspec setting for the existing LSP path.

OBJECT-TYPE

The value of vRtrMplsLspPathOperFRNodeProtect indicates whether the currently operational LSP path has node protection enabled or disabled. When make-before-break functionality for the LSP is enabled and if the LSP node protection setting is changed, the resources allocated to the existing LSP paths will not be released until a new path with the new settings has been established. While a new path is being signaled, the administrative value and the operational values of the path may differ. The value of vRtrMplsLspFRNodeProtect specifies the node protection setting for the new LSP path trying to be established whereas the value of vRtrMplsLspPathOperFRNodeProtect specifies the node protection setting for the existing LSP path.

OBJECT-TYPE

The value of vRtrMplsLspPathOperPropAdminGrp indicates whether the currently operational LSP path has propagation admin groups enabled or disabled. When make-before-break functionality for the LSP is enabled and if the LSP propagate admin groups setting is changed, the resources allocated to the existing LSP paths will not be released until a new path with the new settings has been established. While a new path is being signaled, the administrative value and the operational values of the path may differ. The value of vRtrMplsLspPropAdminGroup specifies the propagate admin groups setting for the new LSP path trying to be established whereas the value of vRtrMplsLspPathOperPropAdminGrp specifies the propagate admin groups setting for the existing LSP path.

OBJECT-TYPE

The value of vRtrMplsLspPathOperFRHopLimit indicates the total number of hops to be used by detour LSP before merging to currently operational LSP path. When make-before-break functionality for the LSP is enabled and if the LSP FR Hop Limit setting is changed, the resources allocated to the existing LSP paths will not be released until a new path with the new settings has been established. While a new path is being signaled, the administrative value and the operational values of the path may differ. The value of vRtrMplsLspFRHopLimit specifies the FR Hop Limit setting for the new LSP path trying to be established whereas the value of vRtrMplsLspPathOperFRHopLimit specifies the FR Hop Limit setting for the existing LSP path.

OBJECT-TYPE

The value of vRtrMplsLspPathOperFRPropAdmGrp indicates whether the currently operational LSP path has propagation of admin groups in the FAST_REROUTE object enabled or disabled. When make-before-break functionality for the LSP is enabled and if the LSP FR propagate admin groups is changed, the resources allocated to the existing LSP paths will not be released until a new path with the new settings has been established. While a new path is being signaled, the administrative value and the operational values of the path may differ. The value of vRtrMplsLspFRPropAdminGroup specifies the FR propagate admin group setting for the new LSP path trying to be established whereas the value of vRtrMplsLspPathOperFRPropAdmGrp specifies the FR propagate admin group setting for the existing LSP path.

OBJECT-TYPE

The value of vRtrMplsLspPathOperInterArea indicates whether the operational LSP path is either inter-area or intra-area.

OBJECT-TYPE

The value of vRtrMplsLspPathOperCompMeth indicates the path computation method that was used for the currently operational LSP path. A value of 'notApplicable' indicates that the LSP path is operationally down or path list is SID.

OBJECT-TYPE

The value of vRtrMplsLspPathOperMetricType indicates the metric type used for the currently operational LSP path. A value of 'notApplicable' indicates that the LSP path is operationally down.

OBJECT-TYPE

The value of vRtrMplsLspPathOperLocalSrProt indicates the local SR protection used for the currently operational LSP path. A value of 'notApplicable' indicates that the LSP path is operationally down.

OBJECT-TYPE

The value of vRtrMplsLspPathOperLabelStackRed indicates whether label stack reduction is used for the currently operational LSP path. A value of 'notApplicable' indicates that the LSP path is operationally down.

OBJECT-TYPE

The vRtrMplsLspPathNgFNAddrType object is an enumerated value that specifies the destination address type of the node in the LSP path at which the LSP path failed.

OBJECT-TYPE

The value of vRtrMplsLspPathNgFNAddr indicates the IP address of the node in the LSP path at which the LSP path failed.

OBJECT-IDENTITY

OBJECT-TYPE

The value of vRtrMplsLabelMaxStaticLspLabels specifies the maximum number of Static LSP labels available on the system. vRtrMplsLabelMaxStaticLspLabels must be set along with vRtrMplsLabelMaxStaticSvcLabels. The total of both values should equal the maximum value allowed of 131040 or 262112 depending on the system. The maximum value of vRtrMplsLabelMaxStaticLspLabels value for most systems is 113040 labels (128 * 1024 less 32 reserved labels). The maximum value of vRtrMplsLabelMaxStaticLspLabels value for chassis mode D systems is 262112 labels (256 * 1024 less 32 reserved labels). vRtrMplsLabelMaxStaticLspLabels is obsoleted in 13.0, replaced by vRtrMplsLabelStaticLabelRange.

OBJECT-TYPE

The value of vRtrMplsLabelMaxStaticSvcLabels specifies the maximum number of Static SVC labels available on the system. vRtrMplsLabelMaxStaticSvcLabels must be set along with vRtrMplsLabelMaxStaticLspLabels. The total of both values should equal the maximum value allowed of 113040 or 262112 depending on the system. The maximum value of vRtrMplsLabelMaxStaticLspLabels value for most systems is 113040 labels (128 * 1024 less 32 reserved labels). The maximum value of vRtrMplsLabelMaxStaticLspLabels value for chassis mode D systems is 262112 labels (256 * 1024 less 32 reserved labels). vRtrMplsLabelMaxStaticSvcLabels is obsoleted in 13.0, replaced by vRtrMplsLabelStaticLabelRange.

OBJECT-TYPE

The value of vRtrMplsLabelBgpLabelsHoldTimer specifies the number of seconds to wait before deleting a BGP label entry based on the next-hop from IOM.

OBJECT-TYPE

The value of vRtrMplsLabelSegRouteStartLabel specifies the start value label available for Segment Routing on the system. vRtrMplsLabelSegRouteStartLabel must be set along with vRtrMplsLabelSegRouteEndLabel.

OBJECT-TYPE

The value of vRtrMplsLabelSegRouteEndLabel specifies the end value label available for Segment Routing on the system. vRtrMplsLabelSegRouteStartLabel must be set along with vRtrMplsLabelSegRouteEndLabel.

OBJECT-TYPE

The value of vRtrMplsLabelStaticLabelRange specifies the range of the Static labels available on the system. vRtrMplsLabelStaticLabelRange maximum value can be 524256 or 1048544 depending on the system profile value (tmnxChassisSystemProfile). For a system configured with system profile as 'profileB', the maximum value of vRtrMplsLabelStaticLabelRange is 1048544 labels (1024 * 1024 less 32 reserved labels). Otherwise, the maximum value of vRtrMplsLabelStaticLabelRange is 524256 labels (512 * 1024 less 32 reserved labels).

OBJECT-TYPE

The value of vRtrMplsLspTempAutoBWTblLastChg indicates the sysUpTime at the time of the last modification to vRtrMplsLspTempAutoBWTable by adding, deleting an entry or change to a writable object in the table. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The vRtrMplsLspTempAutoBWTable has an entry for auto bandwidth configuration for each Labeled Switch Path (LSP) template configured for a virtual router in the system.

OBJECT-TYPE

Each row entry represents auto bandwidth configuration for a Labeled Switch Path (LSP) Template configured for a virtual router in the system.

OBJECT-TYPE

The value of vRtrMplsLspTempAutoBWLastChg indicates the sysUpTime when this row was last modified.

OBJECT-TYPE

The value of vRtrMplsLspTempAutoBWAdjDNPer specifies minimum difference between the current bandwidth reservation of the LSP template and the (measured) maximum average data rate, expressed as a percentage of the current bandwidth, for decreasing the bandwidth of the LSP template. At the adjust interval expiry, if the measured bandwidth falls below the current bandwidth by the value of vRtrMplsLspTempAutoBWAdjDNPer it can cause a resignaling attempt for the LSP template. A value of zero for this object indicates that the threshold check is always true for any measured bandwidth less than current bandwidth.

OBJECT-TYPE

The value of vRtrMplsLspTempAutoBWAdjDNMbps specifies the minimum difference between the current bandwidth reservation of the LSP template and the (measured) maximum average data rate, expressed as an absolute bandwidth (Mbps), for decreasing the bandwidth of the LSP template.

OBJECT-TYPE

The value of vRtrMplsLspTempAutoBWAdjUPPer specifies minimum difference between the current bandwidth reservation of the LSP template and the (measured) maximum average data rate, expressed as a percentage of the current bandwidth, for increasing the bandwidth of the LSP template. At the adjust interval expiry, if the measured bandwidth exceeds the current bandwidth by the value of vRtrMplsLspTempAutoBWAdjUPPer it can cause a resignaling attempt for the LSP template. When the value of vRtrMplsLspTempAutoBWAdjUPPer is 0 it means that this threshold check is always true for any measured bandwidth greater than current bandwidth

OBJECT-TYPE

The value of vRtrMplsLspTempAutoBWAdjUPMbps specifies the minimum difference between the current bandwidth reservation of the LSP template and the (measured) maximum average data rate, expressed as an absolute bandwidth (Mbps), for increasing the bandwidth of the LSP template.

OBJECT-TYPE

The value of vRtrMplsLspTempAutoBWMaxBW specifies the maximum that auto-bandwidth allocation is allowed to request for a LSP template.

OBJECT-TYPE

The value of vRtrMplsLspTempAutoBWMinBW specifies the minimum that auto-bandwidth allocation is allowed to request for a LSP template.

OBJECT-TYPE

The value of vRtrMplsLspTempAutoBWMntrBW specifies whether the collection and display of auto-bandwidth measurements is enabled or disabled for the LSP template. When the value of vRtrMplsLspTempAutoBWMntrBW is 'true' the collection and display of auto-bandwidth measurements is enabled and when the value is 'false' it is disabled.

OBJECT-TYPE

The value of vRtrMplsLspTempAutoBWAdjMult specifies the number of collection intervals in the adjust interval. The default value is derived from vRtrMplsGeneralAutoBWDefAdjMul and vRtrMplsLspAutoBWAdjCount.

OBJECT-TYPE

The value of vRtrMplsLspTempAutoBWOverFlow specifies number of overflow samples that triggers an overflow auto-bandwidth adjustment attempt.

OBJECT-TYPE

The value of vRtrMplsLspTempAutoBWOvrFlwThr specifies the minimum difference between the current bandwidth of the LSP and the sampled data rate, expressed as a percentage of the current bandwidth, for counting an overflow sample.

OBJECT-TYPE

The value of vRtrMplsLspTempAutoBWOvrFlwBW specifies the minimum difference between the current bandwidth of the LSP template and the sampled data rate, expressed as an absolute bandwidth (Mbps), for counting an overflow sample.

OBJECT-TYPE

The value of vRtrMplsLspTempAutoBWSampMult specifies the multiplier for collection intervals in a sample interval.

OBJECT-TYPE

The value of vRtrMplsLspTempAutoBWSampTime indicates the sample multiplier times the collection interval.

OBJECT-TYPE

For each writable object in this row that can be configured to inherit its value from the corresponding object in the vRtrMplsGeneralTable, there is bit within vRtrMplsLspTempAutoBWInherit that controls whether to inherit the operational value of the object or use the administratively set value. This object is a bit-mask, with the following positions: vRtrMplsLspTempAutoBWAdjMult 0x1 vRtrMplsLspTempAutoBWSampMult 0x2 When the bit for an object is set to one, then the object's administrative and operational value are whatever the DEFVAL or most recently SET value is. When the bit for an object is set to zero, then the object's administrative and operational value are inherited from the corresponding object in vRtrMplsGeneralTable.

OBJECT-TYPE

The value of vRtrMplsLspTempAutoBWBeWeight specifies the weight in percent for forwarding class 'BE' for the LSP template.

OBJECT-TYPE

The value of vRtrMplsLspTempAutoBWL2Weight specifies the weight in percent for forwarding class 'L2' for the LSP template.

OBJECT-TYPE

The value of vRtrMplsLspTempAutoBWAfWeight specifies the weight in percent for forwarding class 'AF' for the LSP template.

OBJECT-TYPE

The value of vRtrMplsLspTempAutoBWL1Weight specifies the weight in percent for forwarding class 'L1' for the LSP template.

OBJECT-TYPE

The value of vRtrMplsLspTempAutoBWH2Weight specifies the weight in percent for forwarding class 'H2' for the LSP template.

OBJECT-TYPE

The value of vRtrMplsLspTempAutoBWEfWeight specifies the weight in percent for forwarding class 'EF' for the LSP template.

OBJECT-TYPE

The value of vRtrMplsLspTempAutoBWH1Weight specifies the weight in percent for forwarding class 'H1' for the LSP template.

OBJECT-TYPE

The value of vRtrMplsLspTempAutoBWNcWeight specifies the weight in percent for forwarding class 'NC' for the LSP template.

OBJECT-TYPE

The value of vRtrMplsLspTempAutoBWUnderFlow specifies the number of underflow samples that trigger an underflow auto-bandwidth adjustment attempt.

OBJECT-TYPE

The value of vRtrMplsLspTempAutoBWUndFlwThr specifies the minimum difference between the current bandwidth of the LSP and the sampled data rate, expressed as a percentage of the current bandwidth, for counting an underflow sample.

OBJECT-TYPE

The value of vRtrMplsLspTempAutoBWUndFlwBW specifies the minimum difference between the current bandwidth of the LSP template and the sampled data rate, expressed as an absolute bandwidth (Mbps), for counting an underflow sample.

OBJECT-TYPE

The value of vRtrMplsTemplPlcyBindTblLastChg indicates the sysUpTime at the time of the last modification to vRtrMplsLspTemplPlcyBindTable by adding, deleting an entry or change to a writable object in the table. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The vRtrMplsLspTemplPlcyBindTable has an entry for each policy bound to each Labeled Switch Path (LSP) template configured for a virtual router in the system.

OBJECT-TYPE

Each row entry represents a policy bound to a Labeled Switch Path (LSP) Template configured for a virtual router in the system.

OBJECT-TYPE

The value of the object vRtrMplsLspTemplPlcyBindLastChg indicates the value of the sysUpTime when this entry was last modified.

OBJECT-TYPE

The value of the object vRtrMplsLspTemplPlcyBindRowStat specifies the RowStatus for Policy bound entry.

OBJECT-TYPE

The value of vRtrMplsLspTemplPlcyBind1 specifies the name of the first mpls lsp template policy. This object will be set to its default value when vRtrMplsLspTemplPlcyBindOneHop is set to true.

OBJECT-TYPE

The value of vRtrMplsLspTemplPlcyBind2 specifies the name of the second mpls lsp template policy. This object will be set to its default value when vRtrMplsLspTemplPlcyBindOneHop is set to true.

OBJECT-TYPE

The value of vRtrMplsLspTemplPlcyBind3 specifies the name of the third mpls lsp template policy. This object will be set to its default value when vRtrMplsLspTemplPlcyBindOneHop is set to true.

OBJECT-TYPE

The value of vRtrMplsLspTemplPlcyBind4 specifies the name of the fourth mpls lsp template policy. This object will be set to its default value when vRtrMplsLspTemplPlcyBindOneHop is set to true.

OBJECT-TYPE

The value of vRtrMplsLspTemplPlcyBind5 specifies the name of the fifth mpls lsp template policy. This object will be set to its default value when vRtrMplsLspTemplPlcyBindOneHop is set to true.

OBJECT-TYPE

The value of vRtrMplsLspTemplPlcyBindOneHop specifies whether the one-hop-p2p has been enabled for auto-lsp or not. This object will be set to false when any one of the policy for mpls lsp template is set to its non-default value.

OBJECT-TYPE

Timestamp of the last change to the vRtrMplsLspTempInStatTblLstChg either from adding a row or removing a row.

OBJECT-TYPE

vRtrMplsLspTempInStatTable controls Ingress Statistics for Template based Label Switched Path (LSP).

OBJECT-TYPE

A row in this table represents information about the ingress statistics collection for Template based LSP.

OBJECT-TYPE

The value of vRtrMplsLspTempInStatType indicates the type of template based Label Switched Path (LSP).

OBJECT-TYPE

The value of vRtrMplsLspTempInStatSndrAddrTyp indicates address type of vRtrMplsLspTempInStatSndrAddr.

OBJECT-TYPE

The value of vRtrMplsLspTempInStatSndrAddr indicates the sender address.

OBJECT-TYPE

The value of vRtrMplsLspTempInStatLspNamePref indicates the prefix against which to match the LSP name.

OBJECT-TYPE

vRtrMplsLspTempInStatRowStatus is used for the creation or deletion of entries in the vRtrMplsLspTempInStatTable.

OBJECT-TYPE

The value of vRtrMplsLspTempInStatLastChanged indicates the time stamp of the last change to this row of this table.

OBJECT-TYPE

The value of vRtrMplsLspTempInStatCollectStat specifies whether to collect statistics for this prefix.

OBJECT-TYPE

The value of vRtrMplsLspTempInStatAccntPolicy specifies the accounting policy to be used for this entry. A value of zero indicates that the default accounting policy should be used.

OBJECT-TYPE

The value of vRtrMplsLspTempInStatAdminState specifies whether ingress statistics is enabled for this Label Switched Path (LSP) template.

OBJECT-TYPE

The value of vRtrMplsLspTempInStatMaxStats specifies the maximum number of stat indices assigned to this Label Switched Path (LSP) template session.

OBJECT-TYPE

The value of vRtrMplsLspTempInStatTotlSession indicates the total number of sessions associated with this Label Switched Path (LSP) template statistics.

OBJECT-TYPE

The vRtrMplsLspTable has an entry for each Labeled Switch Path (LSP) configured for a virtual router in the system. This table augments the vRtrMplsLspTable.

OBJECT-TYPE

Each row entry represents a Labeled Switch Path (LSP) configured for a virtual router in the system. Entries can be created and deleted via SNMP SET operations. Each row entry represents a Labeled Switch Path (LSP) configured for a virtual router in the system. Entries can be created and deleted via SNMP SET operations using the vRtrMplsLspRowStatus variable.

OBJECT-TYPE

The value of vRtrMplsLspExtPceCompute specifies whether the LSP path computation request is sent to local CSPF or to PCE. When the value of this object is 'true', the LSP makes a request to PCE to compute the path. When the value of this object is 'false', the path for this LSP is computed locally using CSPF.

OBJECT-TYPE

The value of vRtrMplsLspExtPceControl specifies whether the control of path (delegation) to Path Computation Engine (PCE). Path delegation can be done on locally computed paths and paths computed using PCE.

OBJECT-TYPE

The value of vRtrMplsLspExtPceReport specifies whether to override the global configuration of reporting of LSP to PCE. If the value of vRtrMplsLspExtPceReport is 'disabled' for an LSP either due to inheritance or due to LSP level configuration, the value of vRtrMplsLspExtPceControl has no affect. The default value for vRtrMplsLspExtPceReport is 'inherit'.

OBJECT-TYPE

The value of vRtrMplsLspExtTtmTunnelId indicates the tunnel id sent to TTM for Segment Routing Tunnels on this SROS system.

OBJECT-TYPE

The value of vRtrMplsLspExtMaxSrLabels specifies maximum segment routing label stack size for this LSP. The default IXR platform is 3 and maximum value supported is 5.

OBJECT-TYPE

The value of vRtrMplsLspExtTunnelId indicates the tunnel id used to uniquely identify tunnels on this SROS system.

OBJECT-TYPE

The value of vRtrMplsLspExtEntropyLabel specifies whether the application takes into account the value of Entropy Label and Entropy Label Capability in the label stack for this LSP. When the value of vRtrMplsLspExtEntropyLabel is set to 'enable', the application will account for EL/ELC in the label stack without taking into consideration the value of the enabled ELC. When the value of vRtrMplsLspExtEntropyLabel is set to 'force-disable', the application will ignore the value of enabled ELC. When the value of vRtrMplsLspExtEntropyLabel is modified, Entropy Label will become operational when this LSP is resignalled. By default, if this LSP is of type RSVP-TE it will inherit the behavior as set by vRtrMplsGeneralEntropyLblRsvpTe, or if the LSP is of type SR-TE it will inherit from vRtrMplsGeneralEntropyLblSrTe.

OBJECT-TYPE

The value of vRtrMplsLspExtOperEntropyLabel indicates the operational value of Entropy Label for this LSP. When the value of vRtrMplsLspExtOperEntropyLabel is modified, Entropy Label will become operational when this LSP is resignalled. By default, this LSP will have Entropy Label set to 'force-disable'.

OBJECT-TYPE

The value of vRtrMplsLspExtFrrOverheadLabel specifies maximum additional overhead labels for this LSP.

OBJECT-TYPE

The value of vRtrMplsLspExtNegEntropyLbl indicates the combination of Entropy Label configured at head end for this LSP and the Entropy Label Capability signalled from the far end.

OBJECT-TYPE

The value of vRtrMplsLspExtBfdFailureAction specifies the actions to be taken when this LSP BFD session fails. When vRtrMplsLspExtBfdFailureAction is set to down, it prevents the LSP from being made available as a transport for any user. When vRtrMplsLspExtBfdFailureAction is set to failover, the Lsp is always marked as usable, regardless of the BFD session state. When vRtrMplsLspExtBfdFailureAction is set to failoverOrDown and the BFD session associated with the active-path of the LSP goes down, the LSP will switch to the standby-path if applicable. When the LSP cannot switchover, the LSP will go operationally down.

OBJECT-TYPE

The value of vRtrMplsLspExtCbfFwdingPlcy specifies the name of the Class Forwarding Policy for this LSP instance.

OBJECT-TYPE

The value of vRtrMplsLspExtCbfFwdingSet specifies the Class Forwarding Set ID for this LSP instance. If system profile is profile-b then valid range is 0..6 else 0..4

OBJECT-TYPE

The value of vRtrMplsLspExtPathCompMeth specifies LSP path computation method. If the value of vRtrMplsLspExtPathCompMeth is 'localCspf' for an LSP the path uses local CSPF. If the value of vRtrMplsLspExtPathCompMeth is 'pce' for an LSP the path uses PCE; The default value for vRtrMplsLspExtPathCompMeth is 'none'.

OBJECT-TYPE

The value of vRtrMplsLspExtMetricType specifies metric type. If the value of vRtrMplsLspExtMetricType is 'igp', the metric used is IGP. If the value of vRtrMplsLspExtMetricType is 'te', the metric used is TE. The default value for vRtrMplsLspExtPceReport is 'igp'.

OBJECT-TYPE

The value of vRtrMplsLspExtLocalSrProt specifies the local SR protection. If the value of vRtrMplsLspExtLocalSrProt is 'none', there is no protection. If the value of vRtrMplsLspExtLocalSrProt is 'preferred', the protection is preferred. If the value of vRtrMplsLspExtLocalSrProt is 'mandatory', the protection is mandatory. The default value for vRtrMplsLspExtLocalSrProt is 'none'.

OBJECT-TYPE

The value of vRtrMplsLspExtLabelStackRed specifies whether label stack reduction is enabled.

OBJECT-TYPE

The value of vRtrMplsLspExtBfdUpWaitTimer specifies the time in seconds the software will wait for BFD to come up. The timer object is applicable only when vRtrMplsLspExtBfdFailureAction is set to 'failoverOrDown'. The timer object is applicable for LSPs with vRtrMplsLspType set to 'srTe'. The timer is started when BFD is first enabled on a path or BFD transitions from up to down. When this timer expires and if BFD has not yet come up, the path is torn down by removing it from TTM and the IOM and the retry timer is started.

OBJECT-TYPE

The value of vRtrMplsLspExtSelfPing specifies whether to override the global configuration of Self Ping. If the value of vRtrMplsLspExtSelfPing is 'disabled' for an LSP either due to inheritance or due to LSP level configuration, the value of vRtrMplsLspExtSelfPing has no affect. The default value for vRtrMplsLspExtSelfPing is 'inherit'.

OBJECT-TYPE

Timestamp of the last change to the vRtrMplsLspPathProfTblLstChg either from adding a row or removing a row.

OBJECT-TYPE

The vRtrMplsLspPathProfTable has an entry for each Labeled Switch Path (LSP) configured for a virtual router in the system.

OBJECT-TYPE

Each row entry represents a Labeled Switch Path (LSP) configured for a virtual router in the system. Entries can be created and deleted via SNMP SET operations. Setting RowStatus to 'active' requires vRtrMplsLspPathProfId to have been assigned a valid value.

OBJECT-TYPE

The value of vRtrMplsLspPathProfId specifies the profile id of for the specified LSP.

OBJECT-TYPE

The row status used for creation, deletion, or control of vRtrMplsLspPathProfTable entries. Before the row can be placed into the 'active' state vRtrMplsLspName must have been assigned a valid value.

OBJECT-TYPE

The sysUpTime when this row was last modified.

OBJECT-TYPE

The value of vRtrMplsLspPathProfGroupId specifies the group id used by the path profile for the specified LSP.

OBJECT-TYPE

The value of vRtrMplsClassFwdPlcyTblLstChg indicates the sysUpTime at the time of the last modification of an entry in the vRtrMplsClassFwdPlcyTable.

OBJECT-TYPE

The vRtrMplsClassFwdPlcyTable has an entry for each Forwarding Class Policy configured for a virtual router in the system.

OBJECT-TYPE

Each row entry represents a configuration of a Forwarding Class Policy in the MPLS protocol for a virtual router in the system. Entries can be created and deleted via SNMP SET operations.

OBJECT-TYPE

The value of vRtrMplsClassFwdPlcyName specifies the name for the class forwarding policy.

OBJECT-TYPE

The value of vRtrMplsClassFwdPlcyRowStatus controls the creation and deletion of rows in the table.

OBJECT-TYPE

The value of vRtrMplsClassFwdPlcyLastChanged indicates the sysUpTime when this row was last modified.

OBJECT-TYPE

The value of vRtrMplsClassFwdPlcyDefSetId specifies default forwarding set ID when no forwarding class is specified for Lsp or Lsp Template instance. If system profile is profile-b then valid range is 1..6 else 1..4

OBJECT-TYPE

The value of vRtrMplsClassFwdPlcyRefCount indicates the number of LSPs or LSP templates that are referencing this class forwarding policy.

OBJECT-TYPE

The value of vRtrMplsClassFwdPlcyFCTblLstChg indicates the sysUpTime at the time of the last modification of an entry in the vRtrMplsClassFwdPlcyFCTable.

OBJECT-TYPE

The vRtrMplsClassFwdPlcyFCTable has an entry for each type of Forwarding Class and its corresponding forwarding set id.

OBJECT-TYPE

Each row entry represents a configuration of a Forwarding Class and forwarding set id in the MPLS protocol for a virtual router in the system. Entries can be created and deleted via SNMP SET operations.

OBJECT-TYPE

The value of vRtrMplsClassFwdPlcyFC specifies the name of the forwarding class assigned to the policy name specified by vRtrMplsClassFwdPlcyName.

OBJECT-TYPE

The value of vRtrMplsClassFwdPlcyFCSetId specifies the forwarding set ID to which forwarding class specified by vRtrMplsClassFwdPlcyFC is mapped to. If system profile is profile-b then valid range is 1..6 else 1..4

OBJECT-TYPE

The value of vRtrMplsReservedLblBlkTblLastChg indicates the sysUpTime at the time of the last modification of an entry in the vRtrMplsReservedLblBlkTable.

OBJECT-TYPE

The vRtrMplsReservedLblBlkTable has an entry for each reserved label block.

OBJECT-TYPE

Each row entry represents a configuration of a reserved label block in the MPLS protocol for a virtual router in the system. Entries can be created and deleted via SNMP SET operations.

OBJECT-TYPE

The value of vRtrMplsReservedLblBlkName specifies the name identifying the reserved label block.

OBJECT-TYPE

The row status used for creation, deletion, or control of vRtrMplsReservedLblBlkTable entries.

OBJECT-TYPE

The value of vRtrMplsReservedLblBlkLastChg indicates the sysUpTime when this row was last modified.

OBJECT-TYPE

The value of vRtrMplsReservedLblBlkStartLbl specifies the start value of the reserved label available on the system. vRtrMplsReservedLblBlkStartLbl must be set along with vRtrMplsReservedLblBlkEndLbl.

OBJECT-TYPE

The value of vRtrMplsReservedLblBlkEndLbl specifies the end value of the reserved label available on the system. vRtrMplsReservedLblBlkEndLbl must be set along with vRtrMplsReservedLblBlkStartLbl.

OBJECT-TYPE

The value of vRtrMplsLspAdminTagTblLastChg indicates the sysUpTime at the time of the last modification of an entry in the vRtrMplsLspAdminTagTable.

OBJECT-TYPE

The vRtrMplsLspAdminTagTable has an entry for each admin-tag configured in the system.

OBJECT-TYPE

Each row entry represents a configuration of an admin-tag name in LSP for a virtual router in the system. Entries can be created and deleted via SNMP SET operations.

OBJECT-TYPE

The value of vRtrMplsLspAdminTagName specifies the name of the admin tag.

OBJECT-TYPE

The row status used for creation, deletion, or control of vRtrMplsLspAdminTagTable entries.

OBJECT-TYPE

The value of vRtrMplsLspAdminTagLastChanged indicates the sysUpTime when this row was last modified.

OBJECT-TYPE

The value of vRtrMplsLspTempAdminTagTblLstChg indicates the sysUpTime at the time of the last modification of an entry in the vRtrMplsLspTempAdminTagTable.

OBJECT-TYPE

The vRtrMplsLspTempAdminTagTable has an entry for each admin-tag configured in the system.

OBJECT-TYPE

Each row entry represents a configuration of an admin-tag name in LSP for a virtual router in the system. Entries can be created and deleted via SNMP SET operations.

OBJECT-TYPE

The value of vRtrMplsLspTempAdminTagName specifies the name of the admin tag.

OBJECT-TYPE

The row status used for creation, deletion, or control of vRtrMplsLspTempAdminTagTable entries.

OBJECT-TYPE

The value of vRtrMplsLspTempAdminTagLastChg indicates the sysUpTime when this row was last modified.

OBJECT-TYPE

The value of vRtrMplsFwdPlcyTblLastChg indicates the sysUpTime at the time of the last modification of an entry in the vRtrMplsFwdPlcyTable.

OBJECT-TYPE

The vRtrMplsFwdPlcyTable has an entry for each Forwarding Policy configured for a virtual router in the system.

OBJECT-TYPE

Each row entry represents a configuration of a Forwarding Policy in the MPLS protocol for a virtual router in the system. Entries can be created and deleted via SNMP SET operations.

OBJECT-TYPE

The value of the vRtrMplsFwdPlcyName specifies the name for the forwarding policy.

OBJECT-TYPE

The value of vRtrMplsFwdPlcyRowStatus controls the creation and deletion of rows in the table.

OBJECT-TYPE

The value of vRtrMplsFwdPlcyLastChanged indicates the sysUpTime when this row was last modified.

OBJECT-TYPE

The value of vRtrMplsFwdPlcyAdminState specifies the current administrative state of the forwarding policy.

OBJECT-TYPE

The value of vRtrMplsFwdPlcyOperState indicates the current operational state of the forwarding policy.

OBJECT-TYPE

The value of vRtrMplsFwdPlcyBindingLabel specifies the binding label for the forwarding policy.

OBJECT-TYPE

The value of vRtrMplsFwdPlcyEndpointAddrType specifies the type of vRtrMplsFwdPlcyEndpointAddr.

OBJECT-TYPE

The value of vRtrMplsFwdPlcyEndpointAddr specifies the endpoint address for the forwarding policy.

OBJECT-TYPE

The value of vRtrMplsFwdPlcyRevertTimer specifies the revert timer for the forwarding policy.

OBJECT-TYPE

The value of vRtrMplsFwdPlcyPreference specifies the forwarding policy preference number.

OBJECT-TYPE

This value of vRtrMplsFwdPlcyMetric specifies the metric of this tunnel in the tunnel table.

OBJECT-TYPE

This value of vRtrMplsFwdPlcyTtmPreference specifies the preference of this tunnel in the tunnel table.

OBJECT-TYPE

The value of vRtrMplsFwdPlcyNHGrpTblLastChg indicates the sysUpTime at the time of the last modification of an entry in the vRtrMplsFwdPlcyNHGrpTable.

OBJECT-TYPE

The vRtrMplsFwdPlcyNHGrpTable has an entry for each Forwarding Policy next-hop group configured for a virtual router in the system.

OBJECT-TYPE

Each row entry represents a configuration of a Forwarding Policy next-hop group in the MPLS protocol for a virtual router in the system. Entries can be created and deleted via SNMP SET operations.

OBJECT-TYPE

The value of the vRtrMplsFwdPlcyNHGrpIdx specifies the index for the next-hop group.

OBJECT-TYPE

The value of vRtrMplsFwdPlcyNHGrpRowStatus controls the creation and deletion of rows in the table.

OBJECT-TYPE

The value of vRtrMplsFwdPlcyNHGrpLastChanged indicates the sysUpTime when this row was last modified.

OBJECT-TYPE

The value of vRtrMplsFwdPlcyNHGrpAdminState specifies the current administrative state of the next-hop group.

OBJECT-TYPE

The value of vRtrMplsFwdPlcyNHGrpOperState indicates the current operational state of the next-hop group.

OBJECT-TYPE

The value of vRtrMplsFwdPlcyNHGrpResType specifies the resolution type of the next-hop group. When the value of vRtrMplsFwdPlcyNHGrpResType is set to 'direct', the next-hops in this group must resolve to direct routes for for them to be operational. When the value of vRtrMplsFwdPlcyNHGrpResType is set to 'indirect', the next-hops in this group must resolve to indirect routes for for them to be operational.

OBJECT-TYPE

The value of vRtrMplsFwdPlcyNHGrpLoadBalWt specifies the load balancing weight for this next-hop group.

OBJECT-TYPE

The value of vRtrMplsFwdPlcyNhgNHTblLastChg indicates the sysUpTime at the time of the last modification of an entry in the vRtrMplsFwdPlcyNhgNHTable.

OBJECT-TYPE

The vRtrMplsFwdPlcyNhgNHTable has an entry for each next-hop configured in a Forwarding Policy next-hop group.

OBJECT-TYPE

Each row entry represents a configuration of a next-hop in a Forwarding Policy next-hop group. Entries can be created and deleted via SNMP SET operations.

OBJECT-TYPE

The value of vRtrMplsFwdPlcyNhgNHType specifies the type of next-hop. When the value of vRtrMplsFwdPlcyNhgNHType is set to 'primary', this next-hop will be the primary next-hop in the next-hop group. When the value of vRtrMplsFwdPlcyNhgNHType is set to 'backup', this next-hop will be the backup next-hop in the next-hop group.

OBJECT-TYPE

The value of vRtrMplsFwdPlcyNhgNHRowStatus controls the creation and deletion of rows in the table.

OBJECT-TYPE

The value of vRtrMplsFwdPlcyNhgNHLastChanged indicates the sysUpTime when this row was last modified.

OBJECT-TYPE

The value of vRtrMplsFwdPlcyNhgNHOperState indicates the current operational state of the next-hop.

OBJECT-TYPE

The value of vRtrMplsFwdPlcyNhgNHAddrType specifies the type of vRtrMplsFwdPlcyNhgNHAddr.

OBJECT-TYPE

The value of vRtrMplsFwdPlcyNhgNHAddr specifies the next-hop address.

OBJECT-TYPE

The value of vRtrMplsFwdPlcyGenTblLastChg indicates the sysUpTime at the time of the last modification of an entry in the vRtrMplsFwdPlcyGenTable.

OBJECT-TYPE

The vRtrMplsFwdPlcyGenTable contains objects for general control and management of MPLS Forwarding Policies within a virtual router.

OBJECT-TYPE

Each row entry contains objects for general control and management of MPLS Forwarding Policies within a virtual router. Entries can be created and deleted via SNMP SET operations.

OBJECT-TYPE

The value of vRtrMplsFwdPlcyGenRowStatus controls the creation and deletion of rows in the table.

OBJECT-TYPE

The value of vRtrMplsFwdPlcyGenLastChanged indicates the sysUpTime when this row was last modified.

OBJECT-TYPE

The value of vRtrMplsFwdPlcyGenAdminState specifies the current administrative state for Forwarding Policies configuration.

OBJECT-TYPE

The value of vRtrMplsFwdPlcyGenOperState indicates the current operational state of Forwarding Policies.

OBJECT-TYPE

The value of vRtrMplsFwdPlcyGenOperDownReason indicates the reason due to which Forwarding Policies is operationally down.

OBJECT-TYPE

The value of vRtrMplsFwdPlcyGenReservedLblBlk identifies the reserved label block used by Forwarding Policies.

OBJECT-TYPE

The value of vRtrMplsFwdPlcyStatsTblLastChg indicates the sysUpTime at the time of the last modification of an entry in the vRtrMplsFwdPlcyStatsTable.

OBJECT-TYPE

The vRtrMplsFwdPlcyStatsTable contains objects for general control and management of Statistics for MPLS Forwarding Policies within a virtual router.

OBJECT-TYPE

Each row entry contains objects for general control and management of Statistics for MPLS Forwarding Policies within a virtual router. Entries can be created and deleted via SNMP SET operations.

OBJECT-TYPE

The value of vRtrMplsFwdPlcyStatsType specifies whether the type of statistics is ingress or egress.

OBJECT-TYPE

The value of vRtrMplsFwdPlcyStatsRowStatus controls the creation and deletion of rows in the table.

OBJECT-TYPE

The value of vRtrMplsFwdPlcyStatsLastChanged indicates the sysUpTime when this row was last modified.

OBJECT-TYPE

The value of vRtrMplsFwdPlcyStatsAdminState specifies the current administrative state for Forwarding Policy statistics configuration.

OBJECT-TYPE

The vRtrMplsBindLblPathTable has an entry for each forwarding path associated with a binding label for a virtual router in the system.

OBJECT-TYPE

Each row entry represents a forwarding path associated with a binding label. Entries cannot be created and deleted via SNMP SET operations.

OBJECT-TYPE

The value of vRtrMplsBindLbl specifies the binding label for the forwarding path.

OBJECT-TYPE

The value of vRtrMplsBindLblPathId specifies the path ID for the forwarding path. Path ID will be unique amongst path associated with the same binding label.

OBJECT-TYPE

The value of vRtrMplsBindLblPathOwner indicates the owner for this path.

OBJECT-TYPE

The value of vRtrMplsBindLblPathName indicates the name for this path.

OBJECT-TYPE

The value of vRtrMplsBindLblPathOperState indicates the operational state for this path.

OBJECT-TYPE

The value of vRtrMplsBindLblPathLastOperChg indicates the timestamp when the operational state last changed.

OBJECT-TYPE

The value of vRtrMplsBindLblOperDownReason indicates the reason for the path being operationally down.

OBJECT-TYPE

The value of vRtrMplsBindLblPathNumNHGrpCnt indicates the number of next-hop groups for this path.

OBJECT-TYPE

The value of vRtrMplsBindLblPathRetryCount indicates the number of retry attempts to bring up this path.

OBJECT-TYPE

The value of vRtrMplsBindLblPathRetryTimeRem indicates the time remaining till the next retry to bring up this path.

OBJECT-TYPE

The value of vRtrMplsBindLblPathRevertTimer indicates the revert timer for the path.

OBJECT-TYPE

The value of vRtrMplsBindLblPathIngStatsEnabl indicates whether ingress statistics are enabled for this path.

OBJECT-TYPE

The value of vRtrMplsBindLblPathPref indicates the preference for this path.

OBJECT-TYPE

The value of vRtrMplsBLPathIngStatOperState indicates the operational state of ingress statistics for this path.

OBJECT-TYPE

The value of vRtrMplsBindLblPathEgrStatsEnabl indicates whether egress statistics are enabled for this path.

OBJECT-TYPE

The value of vRtrMplsBLPathEgrStatOperState indicates the operational state of egress statistics for this path.

OBJECT-TYPE

The vRtrMplsBindLblPathNhgTable has an entry for each next-hop group associated with a binding label path.

OBJECT-TYPE

Each row entry represents a next-hop group associated with a binding label path. Entries cannot be created and deleted via SNMP SET operations.

OBJECT-TYPE

The value of vRtrMplsBindLblPathNhgIndex indicates the next-hop group index.

OBJECT-TYPE

The value of vRtrMplsBindLblPathNhgOperState indicates the operational state of this next-hop group.

OBJECT-TYPE

The value of vRtrMplsBindLblPathNHgResType indicates the resolution type of next-hop group. When the value of vRtrMplsBindLblPathNHgResType is 'direct', the next-hops in this group must resolve to direct routes for for them to be operational. When the value of vRtrMplsBindLblPathNHgResType is 'indirect', the next-hops in this group must resolve to indirect routes for for them to be operational.

OBJECT-TYPE

The value of vRtrMplsBindLblPathNhgLoadBalWt indicates the load-balancing weight for this next-hop group.

OBJECT-TYPE

The value of vRtrMplsBindLblPathNhgFailovrCnt indicates the number of failovers from primary to backup next-hop for this next-hop group

OBJECT-TYPE

The value of vRtrMplsBindLblPathNhgRevertCnt indicates the number of reverts from backup to primary next-hop for this next-hop group.

OBJECT-TYPE

The value of vRtrMplsBindLblPathNhgRevTimeRem indicates the time remaining to revert from backup to primary next-hop.

OBJECT-TYPE

The value of vRtrMplsBindLblPathNhgDownReason indicates the reason for the path NHG being operationally down.

OBJECT-TYPE

The value of vRtrMplsBindLblPathNhgWeights indicates the weights for the path next hop group.

OBJECT-TYPE

The vRtrMplsBindLblPathNhgNHTable has an entry for each next-hop in a next-hop group associated with a binding label path.

OBJECT-TYPE

Each row entry represents a next-hop for a next-hop group associated with a binding label path. Entries cannot be created and deleted via SNMP SET operations.

OBJECT-TYPE

The value of vRtrMplsBindLblPathNhgNHType specifies the type of next-hop. When the value of vRtrMplsBindLblPathNhgNHType is set to 'primary', this next-hop will be the primary next-hop in the next-hop group. When the value of vRtrMplsBindLblPathNhgNHType is set to 'backup', this next-hop will be the backup next-hop in the next-hop group.

OBJECT-TYPE

The value of vRtrMplsBindLblPathNhgNHAddrType indicates the address type of the next-hop.

OBJECT-TYPE