TIMETRA-SYSTEM-MIB

TEXTUAL-CONVENTION

The value of TmnxConfigFileFormatType specifies format of the configuration file.

TEXTUAL-CONVENTION

The value of TmnxSsiSyncMode specifies the type of synchronization operation to perform between the primary and secondary CPMs after a change has been made to the configuration files or the boot environment information contained in the boot options file (bof).

TEXTUAL-CONVENTION

The value of TmnxSsiSyncRollbackMode specifies the type of synchronization operation to perform between the primary and secondary CPMs after a change has been made to the rollback files.

TEXTUAL-CONVENTION

The textual convention TmnxSysLicenseAppStatsType represents the type of statistics collected about an application in a virtual machine implementation subject to licensing.

TEXTUAL-CONVENTION

The textual convention TmnxSysLicenseApplication represents an application in a virtual machine implementation that is subject to licensing. NAT - Network Address Translation WLAN-GW - Wireless Local Area Network Gateway LNS - L2TP Network Server Subscriber Management AA - Application Assurance

TEXTUAL-CONVENTION

The textual convention TmnxSysLicensingGroup represents a grouping of licensed applications. system - System Level Licenses services - Service Type Licenses nsp - Network Management Licenses isa - Integrated Services Licenses iom - IOM Card Licenses mda - MDA Licenses

TEXTUAL-CONVENTION

The value of TmnxSysMgmtIfDstoreLockState specifies the datastore lock state.

TEXTUAL-CONVENTION

The value of TmnxSysMonSampleTime specifies the monitoring sample time (in terms of seconds) for a system object.

TEXTUAL-CONVENTION

The value of TmnxSysMonUtilization specifies the utilization/idle percentage (in terms 100ths of a percent) for a given sample-time.

TEXTUAL-CONVENTION

The textual convention TmnxSysNeid represents the Network Element Identifier. The first 8 high-order bits indicate the subnet ID and the 16 low-order bits indicate the basic ID.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

The value of sgiCpuUsage indicates the current CPU utilization for the system.

OBJECT-TYPE

The value of sgiMemoryUsed indicates the total pre-allocated pool memory currently in use on the system. If the value is greater than the maximum value reportable by this object then this object reports its maximum value (4,294,967,295) and sgiKbMemoryUsed must be used to determine the total pre-allocated pool memory.

OBJECT-TYPE

The value of sgiMemoryAvailable indicates the amount of free memory in the overall system that is not allocated to memory pools, but is available in case a memory pool needs to grow. If the value is greater than the maximum value reportable by this object then this object reports its maximum value (4,294,967,295) and sgiKbMemoryAvailable must be used to determine the total free memory.

OBJECT-TYPE

The value of sgiMemoryPoolAllocated indicates the total memory currently allocated in memory-pools on the system. This memory may or may not be currently in use, but is pre-allocated should the software need to use it. If the value is greater than the maximum value reportable by this object then this object reports its maximum value (4,294,967,295) and sgiKbMemoryPoolAllocated must be used to determine the total memory allocated in memory-pools.

OBJECT-TYPE

The value of sgiSwMajorVersion indicates the major version number of the software running on the active CPM card.

OBJECT-TYPE

The value of sgiSwMinorVersion indicates the minor version number of the software running on the active CPM card.

OBJECT-TYPE

The value of sgiSwVersionModifier indicates additional information about the version of software running on the active CPM card.

OBJECT-TYPE

The value of sgiSnmpInGetBulks indicates the total number of SNMP Get-Next PDUs which have been accepted and processed by the SNMP protocol entity.

OBJECT-TYPE

The value of sgiKbMemoryUsed indicates the total pre-allocated pool memory, in kilobytes, currently in use on the system.

OBJECT-TYPE

The value of sgiKbMemoryAvailable indicates the amount of free memory, in kilobytes, in the overall system that is not allocated to memory pools, but is available in case a memory pool needs to grow.

OBJECT-TYPE

The value of sgiKbMemoryPoolAllocated indicates the total memory, in kilobytes, currently allocated in memory-pools on the system. This memory may or may not be currently in use, but is pre-allocated should the software need to use it.

OBJECT-TYPE

tmnxSysCpuMonTable consists of the system level CPU monitoring statistics.

OBJECT-TYPE

tmnxSysCpuMonEntry contains the system level CPU monitoring statistics over a specified sample-time.

OBJECT-TYPE

The value of tmnxSysCpuMonSampleTime specifies the sample-time used to calculate the utilization results for the row.

OBJECT-TYPE

The value of tmnxSysCpuMonCpuIdle indicates the overall percentage of CPU idleness over the specified sample-time.

OBJECT-TYPE

The value of tmnxSysCpuMonBusyCoreUtil indicates the utilization percentage of the busiest processor core over the specified sample-time. On single core CPUs, this is the overall system utilization percentage over the specified sample-time.

OBJECT-TYPE

The value of tmnxSysCpuMonBusyGroupName indicates the name of the group that is running at the highest capacity utilization. Capacity utilization is the CPU utilization relative to the maximum CPU resources available to that group. A group is a set of related applications, services, tasks or protocol handlers that consumes some part of the system CPU resources. The capacity utilization of the busiest group is indicated by tmnxSysCpuMonBusyGroupUtil.

OBJECT-TYPE

The value of tmnxSysCpuMonBusyGroupUtil indicates the capacity utilization of the group that is running at the highest capacity utilization. Capacity utilization is the CPU utilization relative to the maximum CPU resources available to that group. A group is a set of related applications, services, tasks or protocol handlers that consumes some part of the system CPU resources. The name of the busiest group is indicated by tmnxSysCpuMonBusyGroupName.

OBJECT-IDENTITY

OBJECT-TYPE

The value of sgiSystemGroupID specifies a group this system belongs to. It is used by NMS applications to identify a set of systems for which the NMS wants to perform common tasks such as correlating alarms.

OBJECT-TYPE

The value of sgiSystemSubGroupID specifies a sub-group within the sgiSystemGroupID group that this system belongs to. It is used by NMS applications to identify a subset of systems in the sgiSystemGroupID for which the NMS wants to perform common tasks such as correlating alarms.

OBJECT-TYPE

The value of sgiSnmpFailedSets indicates the total number of SNMP set requests which have failed which failed due to another management interface (such as NETCONF) exclusively reserving the system resources.

OBJECT-IDENTITY

OBJECT-TYPE

The current date and time (in UTC) maintained in this managed system.

OBJECT-TYPE

The time zone that is active in this managed system.

OBJECT-TYPE

The number of hours by which the time zone represented by stiActiveZone offsets from UTC (Coordinated Universal Time).

OBJECT-TYPE

The number of minutes (in addition to the hours offset defined by stiHoursOffset) by which the time zone represented by stiActiveZone offsets from UTC (Coordinated Universal Time). This value is used when the time zone does not have an offset that is an integral number of hours. If the hour offset is defined as '12', the minute offset cannot be anything other than zero.

OBJECT-TYPE

stiZoneType will be 'system' if the zone defined by stiActiveZone is a system-defined zone. It will be 'user' if the zone has been defined by the user.

OBJECT-TYPE

The stiSummerZoneTable has an entry for each summer time zone information.

OBJECT-TYPE

Each row entry contains information about a summer time zone. This information can be used to either override the default summer (or daylight savings) time information for a system-defined time zone or define the summer time information for a user-defined time zone.

OBJECT-TYPE

The name for a summer time zone. This name must be unique amongst the table entries. The summer time zone name should comprise only of uppercase letters A-Z and digits 0-9.

OBJECT-TYPE

The row status used to create and delete rows in this table.

OBJECT-TYPE

The starting date and time when the summer time will take effect. This object was made obsolete in the 4.0 release.

OBJECT-TYPE

The date and time when summer time will end. This object was made obsolete in the 4.0 release.

OBJECT-TYPE

The number of minutes that will be added to the time when summer time takes effect. The same number of minutes will be subtracted from the time when the summer time ends.

OBJECT-TYPE

The starting day of the week when the summer time will take effect.

OBJECT-TYPE

The starting week of the month when the summer time will take effect.

OBJECT-TYPE

The starting month of the year when the summer time will take effect.

OBJECT-TYPE

The hour at which the summer time will take effect.

OBJECT-TYPE

The number of minutes after the hours defined by stiSummerZoneStartHour when the summer time will take effect.

OBJECT-TYPE

The day of the week when the summer time setting will end.

OBJECT-TYPE

The week of the month when the summer time setting will end.

OBJECT-TYPE

The month of the year when the summer time setting will end.

OBJECT-TYPE

The hour at which the summer time will stop taking effect.

OBJECT-TYPE

The number of minutes after the hours defined by stiSummerZoneEndHour when the summer time will stop taking effect.

OBJECT-TYPE

The value of stiPreferLocalTime specifies the preference for the use of local or UTC time in the system for objects such as log file names, created/completed times reported in log files, rollback times displayed in show routines etc. Note that the time format for timestamps on log events themselves is controlled on a per log basis and not via prefer-local-time. A value of false(2) means use UTC time; true(1) means use the local system time, configured through 'configure system time' command

OBJECT-IDENTITY

OBJECT-TYPE

The mode for Simple Network Time Protocol (SNTP). 'Unicast' indicates that broadcast client is disabled. A value of 'broadcast' indicates that SNTP is listening to SNTP/NTP broadcast messages on interfaces with broadcast client enabled.

OBJECT-TYPE

The sntpServerEntry has an entry for each SNTP server for SNTP unicast client mode. SNTP can only receive the time from one of these SNTP servers. The table can have up to a maximum of 3 entries.

OBJECT-TYPE

Each row entry contains information about an SNTP server.

OBJECT-TYPE

The IP address of the SNTP server.

OBJECT-TYPE

The row status used to create and delete rows in this table.

OBJECT-TYPE

The SNTP Version supported by this server.

OBJECT-TYPE

The preference value for this SNTP server. When more then one time-server is configured it may be desirable that one server have preference over others. The value of sntpServerPreference for that server will be set to preferred(2). Only one server in the table can be a preferred server

OBJECT-TYPE

The frequency at which this server is queried.

OBJECT-TYPE

The desired administrative state for SNTP.

OBJECT-TYPE

The value of sntpOperStatus indicates the current operational status of SNTP.

OBJECT-IDENTITY

OBJECT-TYPE

Setting this action variable to 'doAction' causes the current running configuration information to be saved to the location specified by ssiSaveConfigDest. If no location is specified by ssiSaveConfigDest, the primary configuration file pointed to in the boot options file (bof) will be backed up and a new primary configuration file will be created with the current running configuration information. If ssiSaveConfigDetail has a value of 'true', default configuration values will be included in the saved configuration information. A corresponding persistent SNMP index file is created regardless of the setting of the persistence switch in the bof.

OBJECT-TYPE

The value of ssiSyncMode specifies the type of synchronization operation to perform between the primary and secondary CPMs after a change has been made to the configuration files or the boot environment information contained in the boot options file (bof).

OBJECT-TYPE

The value of ssiSyncForce specifies the type of synchronization operation to perform when an SNMP set is made to this object. 'config' synchronizes only configuration files. 'bootEnv' synchronizes all files required to boot the system. The result of a read operation on this object is always 'none'.

OBJECT-TYPE

The value of ssiSyncStatus indicates the results of the last synchronization operation between the primary and secondary CPMs.

OBJECT-TYPE

The value of ssiSyncConfigLastTime is the timestamp of the last successful synchronization of the configuration files.

OBJECT-TYPE

The value of ssiSyncBootEnvLastTime is the timestamp of the last successful synchronization of the boot environment files.

OBJECT-TYPE

The value of ssiConfigMaxBackupRevisions is the maximum number of backup revisions maintained for a configuration file. This value also applies to the number of revisions maintained for the BOF file.

OBJECT-TYPE

The value of ssiSaveConfigResult represents the result of the last ssiSaveConfig action. none(1) None of the following apply inProgress(2) The action is still in progress success(3) The action completed successfully failed(4) The action failed

OBJECT-TYPE

Setting ssiSaveBof action variable to 'doAction' causes the existing BOF to be backed up and a new BOF file to be created with the current boot options information.

OBJECT-TYPE

The value of ssiSaveBofResult represents the result of the last ssiSaveBof action. none(1) None of the following apply inProgress(2) The action is still in progress success(3) The action completed successfully failed(4) The action failed

OBJECT-TYPE

The value of ssiSaveConfigDest specifies the destination filepath or file-URL where the current running configuration information will be saved when ssiSaveConfig is set to 'doAction'. If ssiSaveConfigDest is set to the empty string, ''H, the primary configuration file pointed to in the boot options file (bof) will be backed up and a new primary configuration file will be created with the current running configuration information. A corresponding persistent SNMP index file is created regardless of the setting of the persistence switch in the bof.

OBJECT-TYPE

When ssiSaveConfigDetail has a value of 'true', the default configuration values will also be included in the current running configuration information that will be saved when ssiSaveConfig is set to 'doAction'. When ssiSaveConfigDetail has a value of 'false', only non-default configuration values are saved.

OBJECT-TYPE

The value of ssiRedFailoverTime is the timestamp when the last redundancy failover occurred causing a switchover from active to standby CPM. If there is no redundant CPM card in this system or no failover has occurred since the system last booted, ssiRedFailoverTime will always return 0.

OBJECT-TYPE

The value of ssiRedFailoverReason is a text string giving an explanation of the cause of the last redundancy failover. If no failover has occurred, the empty string, ''H, will be returned.

OBJECT-TYPE

The value of ssiSyncRollbackLastTime is the timestamp of the last successful synchronization of the rollback files.

OBJECT-TYPE

The value of ssiSyncRollbackMode specifies the type of synchronization operation to perform between the primary and secondary CPMs after a change has been made to the rollback files.

OBJECT-TYPE

The value of ssiSyncRollbackForce specifies the type of synchronization operation to perform when an SNMP set is made to this object. 'rollbackSingle' synchronizes only the rollback file that recently changed. 'rollbackAll' synchronizes all rollback files. The result of a read operation on this object is always 'none'.

OBJECT-TYPE

The value of ssiSyncRollbackStatus indicates the results of the last rollback synchronization operation between the primary and secondary CPMs.

OBJECT-TYPE

The value of ssiSyncCertLastTime is the timestamp of the last successful synchronization of the certificate files.

OBJECT-TYPE

The value of ssiSyncCertMode specifies whether to synchronize certificate files between the primary and secondary CPMs.

OBJECT-TYPE

The value of ssiSyncCertForce specifies to perform action to synchronize certificate files between the primary and secondary CPMs when an SNMP set is made to this object. The value of ssiSyncCertForce will always be returned as 'notApplicable'.

OBJECT-TYPE

The value of ssiSyncCertStatus indicates the results of the last certificate synchronization operation between the primary and secondary CPMs.

OBJECT-IDENTITY

OBJECT-TYPE

The value of sbiConfigStatus indicates the result of the last attempt to execute the configuration file upon reboot of the system. configRead (1) - The configuration file is being read. configOK (2) - The configuration file was successfully executed. defaultBooted (3) - There was no configuration file and the system booted using a minimal default configuration. bootConfigFailed (4) - An error occurred while the configuration file was being executed. The system configuration is incomplete. bootRestoreFailed (5) - An error occurred while the restoration was being performed. The system configuration is incomplete. auto-provisioning (6) - Auto-Boot feature running to automatically provision and retrieve configuration from network. Execution of boot configuration file skipped.

OBJECT-TYPE

The value of sbiPersistStatus indicates the state of the rebuild of the SNMP persistent index database upon reboot of the system. persistOK (1) - The persistent index database was successfully created. Persistent SNMP managed objects were recreated with the same SNMP indexes they had prior to the system reboot. noPersistFile (2) - There was no persistent index file with the same pathname as the configuration file. persistMismatch (3) -The headers in the persistent index file and the configuration file with the same name do not match. persistIndexFailure (4) - An error occurred while creating the persistent index database. persistDisabled (5) - The system was administratively reconfigured without maintaining persistent SNMP index values because sbiPersistIndex has a value of 'false'. persistInvalid (6) - Persistent index database was not initialized. persistBoot(7) - The persistent index database was in the pre-initial bootup state. persistInit(8) - The persistent index database is initializing. persistInProgress(9) - The initial bootup file is loading, using the persist index database. Once complete, the persist state will go to 'persistOk (1)' if successful. If sbiConfigStatus has a value of 'configOK' and sbiPersistStatus has any value other than 'persistOK', the system was reconfigured without maintaining persistent SNMP index values. Unless sbiPersistIndex has a value of 'false', sbiSnmpdOperStatus returns 'disabled' and the SNMP daemon will not receive SNMP requests until sbiSnmpdAdminStatus variable has been set to 'inService'.

OBJECT-TYPE

When sbiPersistIndex has a value of 'true', the SNMP persistent index database was rebuilt when the system was rebooted. If there was an error during the processing of the configuration file the system may have been reconfigured without persistent SNMP indexes and the SNMP daemon will be suspended until it is manually enabled by setting sbiSnmpdAdminStatus to 'inService. When sbiPersistIndex has a value of 'false' the system was reconfigured without maintaining persistent SNMP index values and the SNMP daemon was enabled.

OBJECT-TYPE

The value of sbiSnmpdAdminStatus is the desired administrative state for the SNMP daemon. When sbiSnmpdAdminStatus is set to 'inService' the SNMP daemon will begin receiving SNMP requests from external SNMP managers. When sbiSnmpdAdminStatus is set to 'outOfService' the SNMP daemon is suspended and will no longer receive SNMP requests from external SNMP managers.

OBJECT-TYPE

When sbiSnmpdOperStatus has a value of 'inService', the SNMP daemon will receive SNMP requests from external SNMP managers. When sbiSnmpdOperStatus has a value of 'outOfService', the SNMP daemon is suspended and will not receive SNMP requests from external SNMP managers.

OBJECT-TYPE

The value of sbiSnmpdMaxPktSize specifies the maximum length in octets of an SNMP message which the SNMP daemon can send or receive and process.

OBJECT-TYPE

The value of sbiSnmpdPortNum specifies the UDP port to send and receive SNMP messages.

OBJECT-TYPE

The value of sbiBootConfigOKScript specifies the location and name of the CLI script file executed following successful completion of the boot-up configuration file execution. I.e. sbiPersistStatus has a value of 'configOK'. When this object has the empty string value, ''H, no CLI script file is executed.

OBJECT-TYPE

The value of sbiConfigOKScriptStatus indicates the results of executing the CLI script file specified in sbiBootConfigOKScript.

OBJECT-TYPE

The value of sbiBootConfigFailScript specifies the location and name of the CLI script file executed following failure of the boot-up configuration file execution. I.e. sbiPersistStatus has a value other than 'configOK'. When this object has the empty string value, ''H, no CLI script file is executed.

OBJECT-TYPE

The value of sbiConfigFailScriptStatus indicates the results of executing the CLI script file specified in sbiBootConfigFailScript.

OBJECT-TYPE

The value of sbiRedSwitchoverScript specifies the location and name of the CLI script file executed following a redundancy switchover from the previously active CPM card. A switchover can happen because of a fatal failure or by manual action. This CLI script file can contain commands for environment settings, debug and mirroring settings, and other commands not maintained by the configuration redundancy. When this object has the empty string value, ''H, no CLI script file is executed.

OBJECT-TYPE

The value of sbiRedSwitchoverScriptStatus indicates the results of executing the CLI script file specified in sbiRedSwitchoverScript.

OBJECT-TYPE

The value of sbiAllowBootLicenseViolations specifies whether the system should allow successful execution of the boot-up configuration file even if it contains license violations. When enabled, the system will not error on any configuration that causes a license violation permitting the system to come into service. However, if violations are detected the system will reboot after one hour if the violations are not fixed.

OBJECT-IDENTITY

OBJECT-TYPE

The radiusOperStatus will have a value of 'up' if any one of the RADIUS servers in the radiusServerTable has the radiusServerOperStatus value of 'up'. It will have a value of 'down' if all the RADIUS servers in the radiusServerTable have the radiusServerOperStatus value of 'down'.

OBJECT-TYPE

The radiusServerEntry has an entry for each RADIUS server. The table can have up to a maximum of 5 entries. Use TIMETRA-SECURITY-MIB::tmnxRadiusServerTable to configure entries.

OBJECT-TYPE

Each row entry contains information about a RADIUS server.

OBJECT-TYPE

The unique value which identifies a specific radius server.

OBJECT-TYPE

The IP address of the RADIUS server. This object was made obsolete in the 5.0 release.

OBJECT-TYPE

Current status of the RADIUS server.

OBJECT-TYPE

The value of radiusServerInetAddressType indicates the address type of radiusServerInetAddress address.

OBJECT-TYPE

The value of radiusServerInetAddress indicates the address of the Radius server.

OBJECT-IDENTITY

OBJECT-TYPE

tmnxNotifyRow is used by the configuration modify, create and delete traps. tmnxNotifyRow specifies the OID of the MIB table entry that was changed.

OBJECT-TYPE

tmnxNotifyRowAdminState is used by the state change notification to specify the administrative state of the MIB table entry reported in the notification.

OBJECT-TYPE

tmnxNotifyRowOperState is used by the state change notification to specify the operational state of the MIB table entry reported in the notification.

OBJECT-TYPE

tmnxMemoryModule is used by the module malloc failed notification to specify the memory module for which the trap is generated.

OBJECT-TYPE

tmnxModuleMallocSize is used by the module malloc failed notification to specify the memory size (in bytes) requested in the failed malloc call.

OBJECT-TYPE

tmnxDroppedTrapID is used by the trap dropped notification to specify the NOTIFICATION-TYPE object identifier of the dropped trap.

OBJECT-TYPE

tmnxTrapDroppedReasonCode is used by the trap dropped notification to specify the reason for which a trap is dropped.

OBJECT-TYPE

tmnxTrapDroppedEntryID is used by the trap dropped notification to specify the table entry associated with the dropped trap.

OBJECT-TYPE

tmnxNotifyEntryOID is used by the configuration modify, create and delete traps. tmnxNotifyEntryOID specifies the OID of the MIB table that was changed.

OBJECT-TYPE

tmnxSnmpdErrorMsg is used by the tmnxSnmpdError notification to indicate the type of SNMP daemon error detected.

OBJECT-TYPE

tmnxPersistencyClient is used by the persistencyClosedAlarmRaised, persistencyClosedAlarmCleared, persistencyFileSysThresRaised and persistencyFileSysThresCleared notification to indicate the affected persistent application.

OBJECT-TYPE

tmnxPersistencyFileLocator is used by the persistencyClosedAlarmRaised, persistencyClosedAlarmCleared, persistencyFileSysThresRaised and persistencyFileSysThresCleared notification to indicate the affected file used to store persistence data.

OBJECT-TYPE

tmnxPersistencyNotifyMsg is used by the persistencyClosedAlarmRaised persistencyClosedAlarmCleared, persistencyEventReport, persistencyFileSysThresRaised and persistencyFileSysThresCleared notification to provide additional information related to the event that occurred.

OBJECT-TYPE

tmnxPersistenceAffectedCpm is used by the persistencyClosedAlarmRaised, persistencyClosedAlarmCleared, persistencyFileSysThresRaised and persistencyFileSysThresCleared notification to indicate the affected CPM.

OBJECT-TYPE

tmnxSysTimeSetBy is used by tmnxSysTimeSetBy notification to indicate who set the time.

OBJECT-TYPE

tmnxFtpFailureMsg is used by tmnxFtpClientFailure notification to indicate FTP error.

OBJECT-TYPE

tmnxFtpFailureDestAddressType is used by tmnxFtpClientFailure notification to indicate the IP address type of the remote host.

OBJECT-TYPE

The value of tmnxFtpFailureDestAddress indicates the IP address of the remote host to which an ftp operation is being attempted on. The value of tmnxFtpFailureDestAddress is used by tmnxFtpClientFailure notification.

OBJECT-TYPE

tmnxNotifyObjectName is used by the configuration modify, create, delete and state change traps. tmnxNotifyObjectName specifies the human readable name of the OID instance of the MIB table entry that was changed.

OBJECT-TYPE

tmnxSyncFailureReason is used by the ssiSyncConfigFailed, ssiSyncBootEnvFailed, and ssiSyncRollbackFailed traps to specify the reason for synchronization failure.

OBJECT-TYPE

The value of tmnxSysExecScript specifies the location and name of the CLI command script file executed by a SROS CLI 'exec' command when the value of tmnxLogExRbkOpType is 'exec (1)'. When the value of tmnxLogExRbkOpType is 'vsd (4)', then the value of tmnxSysExecScript specifies an empty string. It is used by the tmnxSysExecStarted and tmnxSysExecFinished notifications.

OBJECT-TYPE

The value of tmnxSysExecResult indicates the results of executing the CLI script file specified in tmnxSysExecScript. It is used by the tmnxSysExecFinished notification.

OBJECT-TYPE

tmnxSysRollbackFileType is used by tmnxSysRollbackStarted, tmnxSysRollbackSaveStarted, tmnxSysRollbackDeleteStarted, tmnxSysRollbackStatusChange, tmnxSysRollbackSaveStatusChange, and tmnxSysRollbackFileDeleteStatus notifications to indicate the type of file involved in a rollback operation.

OBJECT-TYPE

tmnxSysFileErrorType is used by tmnxSysNvsysFileError notification to indicate the type of file error occurred.

OBJECT-TYPE

The object tmnxTrapDroppedCount is used by the tmnxTrapDropped notification to indicate the number of traps dropped. The value zero indicates that the number of traps dropped is purposely not included in the notification, for example because it is not accurately known.

OBJECT-TYPE

tmnxSysDNSSecDomainName is used by the sysDNSSecFailedAuthentication notification to indicate the domain name of the DNS query.

OBJECT-TYPE

The object tmnxSysLicenseErrorReason indicates the reason for an invalid license.

OBJECT-TYPE

The object tmnxSysLicenseTimeLeft indicates the time remaining for the system to reboot as the result of an invalid license.

OBJECT-TYPE

The value of tmnxSysNotifVsdServerName specifies the VSD server name.

OBJECT-TYPE

The value of tmnxSysNotifXmppServerName indicates the name associated with the XMPP Server.

OBJECT-TYPE

The object tmnxSysLicenseErrorAction indicates the system action taken as a result of tmnxSysLicenseErrorReason.

OBJECT-TYPE

The object tmnxSysNotifAppStatsApplication indicates an application in a virtual machine implementation that is subject to licensing.

OBJECT-TYPE

The object tmnxSysNotifAppStatsType indicates a type of statistics collected about an application in a virtual machine implementation subject to licensing.

OBJECT-TYPE

The object tmnxSysNotifAppStatsTime indicates the time that the system collected statistics' values.

OBJECT-TYPE

tmnxNotifySysMgmtIfOriginalMode indicates the active system interface management mode the system was in when the configuration mode change request was sent.

OBJECT-TYPE

The object tmnxSysLicensingNotifyGroup specifies the licensing group of an application license

OBJECT-TYPE

The object tmnxSysLicensedNotifyAppName specifies the name of the licensed application

OBJECT-TYPE

The value of tmnxPrimaryConfigFileFormatType specifies format of the primary configuration file.

OBJECT-TYPE

The value of tmnxLiConfigFileFormatType specifies format of the li configuration file.

OBJECT-IDENTITY

OBJECT-TYPE

The maximum number of concurrent inbound FTP sessions permitted.

OBJECT-TYPE

The value of slcTelnetInboundMaxSessions specifies the maximum number of concurrent inbound telnet sessions permitted. Note: The actual number of permitted concurrent inbound TELNET sessions may also be restricted by a system wide cumulative limit of 50 concurrent inbound (SSH / TELNET) sessions.

OBJECT-TYPE

The value of slcTelnetOutboundMaxSessions specifies the maximum number of concurrent outbound telnet sessions permitted.

OBJECT-TYPE

The message to be displayed prior to the login prompt of an inbound FTP or telnet session.

OBJECT-TYPE

If the value of slcPreLoginMessageInclName is set to 'TRUE', the slcPreLoginMessage which is displayed prior to the login prompt will contain the system name.

OBJECT-TYPE

The value of object slcMessageOfTheDay specifies the message to display when the user successfully logs in to an inbound FTP, Telnet, SSH or console session. If slcMessageOfTheDayType is set to 'motd-type-none(0)', the value of slcMessageOfTheDay is not displayed. If slcMessageOfTheDayType is set to 'motd-type-url(1)', the syntax of slcMessageOfTheDay is refined to TmnxDisplayStringURL. If slcMessageOfTheDayType is set to 'motd-type-text(2)', the value of slcMessageOfTheDay is the NVT ASCII text to display. Objects slcMessageOfTheDay and slcMessageOfTheDayType must be set together in the same SNMP SET request PDU.

OBJECT-TYPE

The value of object slcMessageOfTheDayType specifies the type of slcMessageOfTheDay. If the value of slcMessageOfTheDayType is set to 'motd-type-none(0)', then the message of the day is not displayed. If the value of slcMessageOfTheDayType is set to 'motd-type-url(1)', then the message is fetched from the URL specified in object slcMessageOfTheDay. If the value of slcMessageOfTheDayType is set to 'motd-type-text(2)', then the value of slcMessageOfTheDay is displayed. Objects slcMessageOfTheDay and slcMessageOfTheDayType must be set together in the same SNMP SET request PDU.

OBJECT-TYPE

If the value of slcLoginBanner is set to 'true', the login banner containing Nokia copyright and version information is displayed prior to the login prompt. If the value is set to 'false', the login banner is not displayed.

OBJECT-TYPE

The value of slcLoginExponentialBackOff specifies if exponential-backoff of the login prompt is enabled. Exponential-backoff is used to deter dictionary attacks. A value of 'true' specifies that exponential-backoff is enabled, while a value of 'false' indicates that exponential-backoff is disabled.

OBJECT-TYPE

The value of slcTelnetGracefulShutdown specifies if graceful shutdown is enabled. A value of 'true' specifies that telnet sessions are closed gracefully by using a TCP FIN/ACK handshake. A value of 'false' indicates that telnet sessions are disconnected by sending a RST (reset) TCP packet.

OBJECT-TYPE

The value of slcSSHGracefulShutdown specifies if graceful shutdown is enabled. A value of 'true' specifies that SSH sessions are closed gracefully by using a TCP FIN/ACK handshake. A value of 'false' indicates that SSH sessions are disconnected by sending a RST (reset) TCP packet.

OBJECT-TYPE

The value of slcTelnetMinTTLValue specifies the minimum TTL value for an incoming packet. This object can only be set if the value of tmnxCpmPerPeerQueuing is 'true (1)'. This value is applied after restarting the Telnet server. If slcTelnetMinTTLValue is set to zero (0), the TTL Security feature is disabled.

OBJECT-TYPE

The value of slcSSHMinTTLValue specifies the minimum TTL value for an incoming packet. This object can only be set if the value of tmnxCpmPerPeerQueuing is 'true (1)'. This value is applied after restarting the SSH server. If slcSSHMinTTLValue is set to zero (0), the TTL Security feature is disabled.

OBJECT-TYPE

The value of slcSSHInboundMaxSessions specifies the maximum number of concurrent inbound SSH sessions permitted. Note: The actual number of permitted concurrent inbound SSH sessions may also be restricted by a system wide cumulative limit of 50 concurrent inbound (SSH / TELNET) sessions.

OBJECT-TYPE

The value of slcSSHOutboundMaxSessions specifies the maximum number of concurrent outbound SSH sessions permitted.

OBJECT-TYPE

The value of the object slcIdleTimeout specifies the maximum time of how long a user initiated session (console, telnet, SSH, FTP) can be inactive before it will be automatically closed by the system. The value of 9999 specifies that the system will never automatically close an inactive user initiated session.

OBJECT-TYPE

The value of the object slcLoginScriptGlobal specifies the URL of a CLI script that is executed when any user opens a CLI session. This allows an operator, for example, to define a common set of CLI aliases that are made available on the router for all users. This global login-exec script is executed before any user-specific login-exec file that may be configured.

OBJECT-TYPE

The value of the object slcLoginScriptPerUserDirectory specifies the user-directory of the per-user login script configured in slcLoginScriptPerUserFilename. This per-user script is executed before any other user-specific login script, like the one configured in tmnxUserConsoleLoginExecFile or the one specified in RADIUS attribute Timetra-Exec-File (6527-8).

OBJECT-TYPE

The value of the object slcLoginScriptPerUserFilename specifies the filename of the per-user login script. The per-user login script is defined by concatenating the value of slcLoginScriptPerUserDirectory, the username, and the value of slcLoginScriptPerUserFilename. For example : If the value of slcLoginScriptPerUserDirectory is 'cf1:/local/users' and the value of slcLoginScriptPerUserFilename is 'login-script.txt', then file 'cf1:/local/users/john/login-script.txt' is executed when user 'john' opens a CLI session.

OBJECT-IDENTITY

OBJECT-TYPE

sysLACPSystemPriority is the Link Aggregation Control Protocol (LACP) system priority which is combined with the system MAC address to make up a unique system ID that is used by LACP in communications with LACP peer systems on Link Aggregation (LAG) ports.

OBJECT-IDENTITY

OBJECT-TYPE

The tacplusOperStatus will have a value of 'up' if any one of the TACACS+ servers in the tacplusServerTable has the tacplusServerOperStatus value of 'up'. It will have a value of 'down' if all the TACACS+ servers in the tacplusServerTable have the tacplusServerOperStatus value of 'down'.

OBJECT-TYPE

The tacplusServerEntry has an entry for each TACACS+ server. The table can have up to a maximum of 5 entries. Use TIMETRA-SECURITY-MIB::tmnxTacPlusServerTable to configure entries.

OBJECT-TYPE

Each row entry contains information about a TACACS+ server.

OBJECT-TYPE

The unique value which identifies a specific TACACS+ server.

OBJECT-TYPE

The IP address of the TACACS+ server. This object was made obsolete in the 5.0 release.

OBJECT-TYPE

Current status of the TACACS+ server.

OBJECT-TYPE

The value of tacPlusServerInetAddressType indicates the address type of tacPlusServerInetAddress address.

OBJECT-TYPE

The value of tacPlusServerInetAddress indicates the address of the Tacplus server.

OBJECT-IDENTITY

OBJECT-TYPE

The value of sbiActiveIpAddr specifies the IP address of the ethernet port on the active CPM.

OBJECT-TYPE

The value of sbiActiveIpMask specifies the mask length of the subnet associated with the IP address of the ethernet port on the active CPM.

OBJECT-TYPE

The value of sbiStandbyIpAddr specifies the IP address of the ethernet port on the standby CPM.

OBJECT-TYPE

The value of sbiStandbyIpMask specifies the mask length of the subnet associated with the IP address of the ethernet port on the standby CPM.

OBJECT-TYPE

The value of sbiPrimaryImage specifies the primary location of the directory that contains the runtime image files.

OBJECT-TYPE

The value of sbiSecondaryImage specifies the secondary location of the directory that contains the runtime image files.

OBJECT-TYPE

The value of sbiTertiaryImage specifies the tertiary location of the directory that contains the runtime image files.

OBJECT-TYPE

The value of sbiPrimaryConfigFile specifies the location and name of the primary configuration file.

OBJECT-TYPE

The value of sbiSecondaryConfigFile specifies the location and name of the secondary configuration file.

OBJECT-TYPE

The value of sbiTertiaryConfigFile specifies the location and name of the tertiary configuration file.

OBJECT-TYPE

The value of sbiPersist specifies whether or not the system will preserve SNMP indexes between reboots. When set to 'true', persistent indexing is enabled.

OBJECT-TYPE

The value of sbiConsoleSpeed specifies the baud rate of the console port.

OBJECT-TYPE

The value of sbiAutoNegotiate determines whether or not the speed and duplex parameters will be automatically negotiated on the CPM ethernet port. When set to 'true', auto-negotiation is enabled.

OBJECT-TYPE

The value of sbiSpeed specifies the speed of the CPM ethernet port. This value is ignored if auto-negotiation is enabled.

OBJECT-TYPE

The value of sbiDuplex specifies the duplex mode for the CPM ethernet port. This value is ignored if auto-negotiation is enabled.

OBJECT-TYPE

The value of sbiPrimaryDns specifies the IP address of the primary DNS server to use for DNS name resolution.

OBJECT-TYPE

The value of sbiSecondaryDns specifies the IP address of the secondary DNS server to use for DNS name resolution.

OBJECT-TYPE

The value of sbiTertiaryDns specifies the IP address of the tertiary DNS server to use for DNS name resolution.

OBJECT-TYPE

The value of sbiDnsDomain specifies the domain name to use when performing DNS address resolution.

OBJECT-TYPE

The value of sbiWait specifies the number of seconds the system pauses at the start of the boot process. This pause allows the operator to interrupt the system initialization at the console and manually override the parameters in the BOF.

OBJECT-TYPE

The sbiStaticRouteTable contains an entry for each static route configured for the CPM ethernet port. These static routes are only used to route traffic generated by the CPM ethernet port. The table can have up to a maximum of 10 entries.

OBJECT-TYPE

Each row entry contains information about a static route configured for the CPM ethernet port. Entries in this table can be created and deleted via SNMP SET operations to sbiStaticRouteRowStatus.

OBJECT-TYPE

The value of sbiStaticRouteDest specifies the destination IP address of this static route.

OBJECT-TYPE

The value of sbiStaticRouteMask specifies the length of the subnet mask associated with the destination IP address of this static route.

OBJECT-TYPE

The value of sbiStaticRouteNextHop specifies the IP address of the next hop for this static route. This IP address should be in the same subnet as the ethernet port on the active CPM. The value of sbiStaticRouteNextHop must be set to a valid IP address for the row creation to succeed.

OBJECT-TYPE

sbiStaticRouteRowStatus controls the creation and deletion of rows in the table. To create a row in this table, set the row status to createAndGo(4)'. The value of sbiStaticRouteNextHop must also be set to a valid IP address for the row creation to succeed. To delete a row in this table, set the row status to delete(6).

OBJECT-TYPE

The value of sbiActiveIPv6Addr specifies the IPv6 address of the ethernet port on the active CPM.

OBJECT-TYPE

The value of sbiActiveIPv6PfxLen specifies the prefix length of the subnet associated with the sbiActiveIPv6Addr address of the ethernet port on the active CPM.

OBJECT-TYPE

The value of sbiStandbyIPv6Addr specifies the IPv6 address of the ethernet port on the standby CPM.

OBJECT-TYPE

The value of sbiStandbyIPv6PfxLen specifies the prefix length of the subnet associated with the sbiStandbyIPv6Addr address of the ethernet port on the active CPM.

OBJECT-TYPE

The value of sbiPrimaryDnsIPv6Addr specifies the IPv6 address of the primary DNS server to use for DNS name resolution.

OBJECT-TYPE

The value of sbiSecondaryDnsIPv6Addr specifies the IPv6 address of the secondary DNS server to use for DNS name resolution.

OBJECT-TYPE

The value of sbiTertiaryDnsIPv6Addr specifies the IPv6 address of the tertiary DNS server to use for DNS name resolution.

OBJECT-TYPE

The sbiStaticRouteIPv6Table contains an entry for each static IPv6 route configured for the CPM ethernet port. These static routes are only used to route traffic generated by the CPM ethernet port. The table can have up to a maximum of 10 entries.

OBJECT-TYPE

Each row entry contains information about a static IPv6 route configured for the CPM ethernet port. Entries in this table can be created and deleted via SNMP SET operations to sbiStaticRouteIPv6RowStatus.

OBJECT-TYPE

The value of sbiStaticRouteIPv6Dest specifies the destination IPv6 address of this static route.

OBJECT-TYPE

The value of sbiStaticRouteIPv6PfxLen specifies the prefix length of sbiStaticRouteIPv6Dest, the destination IPv6 address of this static route.

OBJECT-TYPE

The value of sbiStaticRouteIPv6NextHop specifies the IPv6 address of the next hop for this static route. This IPv6 address should be in the same subnet as the ethernet port on the active CPM. The value of sbiStaticRouteIPv6NextHop must be set to a valid IPv6 address for the row creation to succeed.

OBJECT-TYPE

sbiStaticRouteIPv6RowStatus controls the creation and deletion of rows in the table. To create a row in this table, set the row status to createAndGo(4)'. The value of sbiStaticRouteIPv6NextHop must also be set to a valid IPv6 address for the row creation to succeed. To delete a row in this table, set the row status to delete(6).

OBJECT-TYPE

The value of sbiLiSeparate specifies whether or not a non-LI user has access to Lawful Intercept (LI) information. When sbiLiSeparate has a value of 'true', a user who does not have the TIMETRA-SECURITY-MIB:: tmnxUserAccess 'li' bit set will not be allowed to access CLI or SNMP objects in the 'li' context. A change to the value of this object does not take affect until the system is rebooted.

OBJECT-TYPE

The value of sbiLiLocalSave specifies whether or not Lawful Intercept (LI) configuration is allowed to be save to a local file. A change to the value of this object does not take affect until the system is rebooted.

OBJECT-TYPE

The value of sbiLicenseFile specifies the location and name of the license file.

OBJECT-TYPE

The value of sbiFips1402Level1 specifies whether or not the security level 1 of Federal Information Processing Standards 140 series version 2 (FIPS-140-2) is enabled. A change to the value of this object does not take effect until after a system reboot. If the value of sbiFips1402Level1 is 'true (1)', after a system reboot, any configuration that is not supported by FIPS-140-2 level 1, will be retrievable via SNMP requests.

OBJECT-TYPE

The value of sbiSystemBaseMacAddress specifies the administratively configured base system ethernet MAC address. Special purpose MAC addresses used by the system software are constructed from this base address. The value is the first MAC address in a contiguous range of 1024 addresses. If configured, sbiSystemBaseMacAddress will override the value given by tmnxChassisBaseMacAddress. A value of all zeroes indicates this object is not configured.

OBJECT-TYPE

The value of sbiEssSystemType specifies whether or not the system is administratively configured to function as a Nokia SROS Ethernet Service Switch (ESS).

OBJECT-TYPE

The value of sbiSystemProfile specifies the system profile in the BOF. 'none (0)' - No system profile set, permits the co-existence of FP3 and FP4-based line cards in the system. 'profileA (1)- This system profile is primarily targeted at subscriber services and layer 2/3 VPN business services. 'profileB (2)- This system profile is primarily targeted at infrastructure routing, core, peering, and DC-GW applications.

OBJECT-TYPE

The value of sbiAutoBoot specifies whether or not the system will run the auto-provisioning agent.

OBJECT-TYPE

The value of sbiAutoBootClientId specifies the identifier to use when performing network discovery requests.

OBJECT-TYPE

The value of sbiAutoBootClientIdType represents how the value of sbiAutoBootClientId is encoded: - 'none (1)' : no identification has been specified - 'ascii(2)' : this option contains seven-bit ASCII characters - 'hex (3)' : this option contains octets. It must be displayed in hexadecimal format because it contains non-printable characters. - 'mac (4)' : this type is the chassis mac in octets. It must be displayed in hexadecimal format because it contains non-printable characters.

OBJECT-TYPE

The value of sbiAutoBootUsingMgmt specifies whether or not the system will auto-boot using the management port.

OBJECT-TYPE

The value of sbiAutoBootUsingInband specifies whether or not the system will auto-boot using the inband ports.

OBJECT-TYPE

The value of sbiAutoBootInbandVlan specifies a VLAN that the system will use for auto-boot on inband ports.

OBJECT-TYPE

The value of sbiAutoBootUsingIpv4 specifies whether or not the system will send IPv4 DHCP Discovery requests.

OBJECT-TYPE

The value of sbiAutoBootUsingIpv6 specifies whether or not the system will send IPv6 DHCP Solicit requests.

OBJECT-TYPE

The value of sbiAutoBootIncludeUserClass specifies whether or not the system will include User Class data information in IPv4/IPv6 DHCP requests.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

The value of sbiAutoIpv4Dhcp specifies if the system sends IPv4 DHCP Discovery requests.

OBJECT-TYPE

The value of sbiAutoIpv4DhcpClientIdType specifies how the value of sbiAutoIpv4DhcpClientId has to be interpreted: - 'default (1)' : use the chassis serial number, formatted as ASCII characters - 'ascii(2)' : seven-bit ASCII characters - 'hex (3)' : octets, possibly non-printable characters.

OBJECT-TYPE

The value of sbiAutoIpv4DhcpClientId specifies the client identifier.

OBJECT-TYPE

The value of sbiAutoIpv4DhcpOptUserClass specifies if the system DHCP client sends the User Class option.

OBJECT-TYPE

The value of the object sbiAutoIpv4DhcpTimeout specifies the maximum time the system DHCP client waits for a DHCPOFFER message. While the system waits for the DHCPOFFER message, reading of the configuration file is suspended.

OBJECT-IDENTITY

OBJECT-TYPE

The value of sbiAutoIpv6Dhcp specifies if the system sends IPv6 DHCP Solicit requests.

OBJECT-TYPE

The value of sbiAutoIpv6DhcpClientIdType specifies how the DHCPv6 client generates the Client Identifier option. A value of 'default' means the DHCPv6 client uses a Client Identifier with the chassis serial number, formatted as ASCII characters, in the variable length identifier following the DUID-EN type code and enterprise-number.

OBJECT-TYPE

The value of sbiAutoIpv6DhcpClientIdDuidType specifies how the DUID in the sbiAutoIpv6DhcpClientIdDuid has to be interpreted. When the value of sbiAutoIpv6DhcpClientIdType is equal to 'duidEnterprise', a value other than 'none' must be specified. A value other than 'none' is only allowed when the value of sbiAutoIpv6DhcpClientIdType is equal to 'duidEnterprise'.

OBJECT-TYPE

The value of sbiAutoIpv6DhcpClientIdDuid specifies the client identifier DHCP Unique Identifier (DUID). When the value of sbiAutoIpv6DhcpClientIdDuidType is not equal to 'none', a non-empty value must be specified. A non-empty value is only allowed when the value of sbiAutoIpv6DhcpClientIdDuidType is not equal to 'none'.

OBJECT-TYPE

The value of sbiAutoIpv6DhcpOptUserClass specifies if the system DHCPv6 client sends the User Class option.

OBJECT-TYPE

The value of the object sbiAutoIpv6DhcpTimeout specifies the maximum time the system DHCPv6 client waits for an ADVERTISE message. While the system waits for the ADVERTISE message, reading of the configuration file is suspended.

OBJECT-TYPE

The value of sbiStandbyAIpAddr specifies the IP address of the ethernet port on CPM A if CPM A is the standby CPM.

OBJECT-TYPE

The value of sbiStandbyAIpMask specifies the mask length of the subnet associated with the IP address of the ethernet port on CPM A if CPM A is the standby CPM.

OBJECT-TYPE

The value of sbiStandbyAIPv6Addr specifies the IPv6 address of the ethernet port on CPM A if CPM A is the standby CPM

OBJECT-TYPE

The value of sbiStandbyAIPv6PfxLen specifies the prefix length of the subnet associated with the sbiStandbyAIPv6Addr address of the ethernet port on CPM A if CPM A is the standby CPM

OBJECT-TYPE

The value of sbiStandbyBIpAddr specifies the IP address of the ethernet port on CPM B if CPM B is the standby CPM.

OBJECT-TYPE

The value of sbiStandbyBIpMask specifies the mask length of the subnet associated with the IP address of the ethernet port on CPM B if CPM B is the standby CPM.

OBJECT-TYPE

The value of sbiStandbyBIPv6Addr specifies the IPv6 address of the ethernet port on CPM B if CPM B is the standby CPM

OBJECT-TYPE

The value of sbiStandbyBIPv6PfxLen specifies the prefix length of the subnet associated with the sbiStandbyBIPv6Addr address of the ethernet port on CPM B if CPM B is the standby CPM

OBJECT-TYPE

The value of sbiStandbyCIpAddr specifies the IP address of the ethernet port on CPM C if CPM C is the standby CPM.

OBJECT-TYPE

The value of sbiStandbyCIpMask specifies the mask length of the subnet associated with the IP address of the ethernet port on CPM C if CPM C is the standby CPM.

OBJECT-TYPE

The value of sbiStandbyCIPv6Addr specifies the IPv6 address of the ethernet port on CPM C if CPM C is the standby CPM

OBJECT-TYPE

The value of sbiStandbyCIPv6PfxLen specifies the prefix length of the subnet associated with the sbiStandbyCIPv6Addr address of the ethernet port on CPM C if CPM C is the standby CPM

OBJECT-TYPE

The value of sbiStandbyDIpAddr specifies the IP address of the ethernet port on CPM D if CPM D is the standby CPM.

OBJECT-TYPE

The value of sbiStandbyDIpMask specifies the mask length of the subnet associated with the IP address of the ethernet port on CPM D if CPM D is the standby CPM.

OBJECT-TYPE

The value of sbiStandbyDIPv6Addr specifies the IPv6 address of the ethernet port on CPM D if CPM D is the standby CPM

OBJECT-TYPE

The value of sbiStandbyDIPv6PfxLen specifies the prefix length of the subnet associated with the sbiStandbyDIPv6Addr address of the ethernet port on CPM D if CPM D is the standby CPM

OBJECT-TYPE

The value of sbiMgmtIfIpMtu is used to reflect configures the IP maximum transmit unit (packet) for the management router instance. The configured IP-MTU cannot be larger than the calculated IP MTU based on the port MTU configuration. When a SNMP SET request is received with a value of zero (0), the agent actually sets vRtrIfMtu to the calculated default size.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

The value of spiDhcpL2PersistenceFileLocation specifies the flash device on a CPM card where the data for handling DHCP Layer2 persistency is stored. The value 0 indicates that no flash device is specified. This object was made obsolete in the 5.0 release.

OBJECT-TYPE

The value of the object spiDhcpL2PersistenceDescription specifies a user provided description related to DHCP Layer-2 persistency. It consists of any printable, seven-bit ASCII characters up to 80 characters in length. This object was made obsolete in the 5.0 release.

OBJECT-IDENTITY

OBJECT-TYPE

The value of spiDhcpL3PersistenceFileLocation specifies the flash device on a CPM card where the data for handling DHCP Layer3 persistency is stored. The value 0 indicates that no flash device is specified. This object was made obsolete in the 5.0 release.

OBJECT-TYPE

The value of the object spiDhcpL3PersistenceDescription specifies a user provided description related to DHCP Layer-3 persistency. It consists of any printable, seven-bit ASCII characters up to 80 characters in length. This object was made obsolete in the 5.0 release.

OBJECT-IDENTITY

OBJECT-TYPE

The value of spiSubMgmtPersistenceFileLocation specifies the flash device on a CPM card where the data for handling subscriber management persistency is stored. The value 0 indicates that no flash device is specified.

OBJECT-TYPE

The value of the object spiSubMgmtPersistenceDescription specifies a user provided description related to subscriber management persistency. It consists of any printable, seven-bit ASCII characters up to 80 characters in length.

OBJECT-IDENTITY

OBJECT-TYPE

The value of spiDhcpSrvPersistenceFileLoc specifies the flash device on a CPM card where the data for handling the local DHCP server persistency is stored. The value 0 indicates that no flash device is specified.

OBJECT-TYPE

The value of the object spiDhcpSrvPersistenceDescr specifies a user provided description related to the local DHCP server persistency. It consists of any printable, seven-bit ASCII characters up to 80 characters in length.

OBJECT-IDENTITY

OBJECT-TYPE

The value of spiNatFwdPersistenceFileLoc specifies the flash device on a CPM card where the data for handling the NAT (Network Address Translation) port forwarding persistence is stored. The value 0 indicates that no flash device is specified.

OBJECT-TYPE

The value of the object spiNatFwdPersistenceDescr specifies a user provided description related to the NAT port forwarding persistence. It consists of any printable, seven-bit ASCII characters up to 80 characters in length.

OBJECT-IDENTITY

OBJECT-TYPE

The value of spiAAPersistenceFileLoc specifies the flash device on a CPM card where the data for handling the AA (Application Assurance) persistence is stored. The value 0 indicates that no flash device is specified.

OBJECT-TYPE

The value of the object spiAAPersistenceDescr specifies a user provided description related to the AA (Application Assurance) persistence. It consists of any printable, seven-bit ASCII characters up to 80 characters in length.

OBJECT-IDENTITY

OBJECT-TYPE

The value of spiAncpPersistenceFileLoc specifies the flash device on a CPM card where the data for handling the Ancp persistence is stored. The value 0 indicates that no flash device is specified.

OBJECT-TYPE

The value of the object spiAncpPersistenceDescr specifies a user provided description related to the Ancp persistence. It consists of any printable, seven-bit ASCII characters up to 80 characters in length.

OBJECT-IDENTITY

OBJECT-TYPE

The value of spiPythonPersistenceFileLoc specifies the flash device on a CPM card where the data for handling the python persistence is stored. The value 0 indicates that no flash device is specified.

OBJECT-TYPE

The value of the object spiPythonPersistenceDescr specifies a user provided description related to the Python persistence. It consists of any printable, seven-bit ASCII characters up to 80 characters in length.

OBJECT-TYPE

The value of tmnxDhcpLeaseTimeModeThreshold specifies the threshold time for DHCP leases to be eligible for persistence in the 'lease time mode' of operation. Normally, the expiry time of a DHCP lease is stored in the persistent database; in 'lease time mode', however, the full lease time is stored; the resource usage penalty is reasonably small for leases with sufficiently short lease times. DHCP leases with a lease time greater than the value of tmnxDhcpLeaseTimeModeThreshold have their expiry time stored as usual. DHCP leases with a lease time smaller than or equal to the value of tmnxDhcpLeaseTimeModeThreshold have their full lease time stored.

OBJECT-IDENTITY

OBJECT-TYPE

The value of sliConfigStatus indicates the results of restoring the Lawful Intercept (LI) configuration at boot-up time.

OBJECT-TYPE

The value of sliSaveConfig specifies a desired action. Setting this action variable to 'doAction' causes the current Lawful Intercept (LI) running configuration information, to be saved to a file called li.cfg in the same location as the BOF file. If the li.cfg file already exists, it will be renamed and a new file is created with the current running configuration. An attempt to set this object to 'doAction' when the booted value of sbiLiLocalSave is 'false' will result in an 'inconsistentValue' error. Default configuration values will be included in the saved configuration information.

OBJECT-TYPE

The value of sliSaveConfigResult represents the result of the last sliSaveConfig action. none(1) None of the following apply inProgress(2) The action is still in progress success(3) The action completed successfully failed(4) The action failed

OBJECT-TYPE

The value of sliConfigLastModified indicates the date and time the Lawful Intercept (LI) running configuration was last modified. If sliConfigLastModified is more recent than TIMETRA-CHASSIS-MIB:: tmnxHwSwLastBoot, the current configuration may be different than that in the configuration file read upon system initialization.

OBJECT-TYPE

The value of sliConfigLastSaved indicates the date and time the current Lawful Intercept (LI) configuration was last saved. If sliConfigLastSaved is more recent than the value of TIMETRA-CHASSIS-MIB::tmnxHwSwLastBoot, the initial configuration is likely to be different the next time the system is rebooted.

OBJECT-TYPE

The of sliFilterLock specifies who can modify the Lawful Intercept (LI) filters. The value: 'locked': no users can modify the LI filters 'unlockedForLiUsers': only users with LI privileges can modify the LI filters 'unlockedForAll': all users can modify the LI filters.

OBJECT-IDENTITY

OBJECT-TYPE

The value of sysDNSInfoLastChanged is the timestamp of the last configuration changes to any of the DNS global settings.

OBJECT-TYPE

The value of sysDNSAddressResolvePref specifies how the DNS client will request for address resolution. ipv4-only: The DNS client will only try to resolve a domain name into an ipv4 address. ipv6-first: the DNS client will first try to resolve the domain name in to ipv6 address. If no ipv6 address is available it will try to resolve the domain name into an ipv4 address.

OBJECT-TYPE

The value of sysDNSSecAdValidation specifies whether or not the presence of the Authenticated Data (AD) bit in responses is validated from the DNS servers. When sysDNSSecAdValidation is set to 'true (1)', DNSSEC validation is enabled and a warning is reported to the SECURITY log if the AD-bit is not set in responses from the DNS servers. The notification responsible for the warning is sysDNSSecFailedAuthentication. When sysDNSSecAdValidation is set to 'false (2)', DNSSEC validation of the AD-bit is disabled.

OBJECT-TYPE

The value of sysDNSSecRespCtrl specifies whether the system will permit or reject DNS responses that do not pass DNSSEC validation. The value of this object is ignored if sysDNSSecAdValidation is set to 'false (2)'. When sysDNSSecRespCtrl is set to 'fallThrough (1)', the system will permit DNS responses that do not pass DNSSEC validation, allowing the resolution to complete. When sysDNSSecRespCtrl is set to 'drop (2)', the system will reject DNS responses that do not pass DNSSEC validation, and the resolution will appear to fail.

OBJECT-IDENTITY

OBJECT-TYPE

The value of sysIcmpVSEnhancement specifies if vendor specific extensions to ICMP is enabled or not.

OBJECT-IDENTITY

OBJECT-TYPE

The value of sysNewQinqUntaggedSap controls the forwarding of packets on a QinQ X.0 access SAP. When sysNewQinqUntaggedSap is set to true, the SAP will only accept: - frames with a single tag matching the SAP's outer tag or, - frames with double tag where the outer tag matches the SAP's outer tag and inner tag is set to 0. When sysNewQinqUntaggedSap is set to false, forwarding of packets remains unchanged.

OBJECT-IDENTITY

OBJECT-TYPE

The value of tmnxSysRollbackIndex specifies a specific rollback checkpoint file to which a rollback action can be taken. The value of the tmnxSysRollbackIndex corresponds to a rollback checkpoint file with suffix .rb.index. The maximum checkpoint file that can be specified is determined by the rollback location as specified by tmnxSysRollbackLocation. If the location is on a compact flash, then the maximum value of tmnxSysRollbackIndex can be tmnxSysRollbackMaxLocalFiles minus 1. If the location is a remote ftp location, then the maximum value of tmnxSysRollbackIndex can be tmnxSysRollbackMaxRemoteFiles minus 1. This index is SET along with another action object, including tmnxSysRollbackStart to initiate a rollback revert of a file and tmnxSysRollbackFileDelete to delete a rollback file. An SNMP GET request on this object should return the last SET value.

OBJECT-TYPE

The value of tmnxSysRollbackStart specifies whether to revert the rollback file specified by tmnxSysRollbackIndex. When SET to the value of 'doAction' the system will revert the rollback file specified by tmnxSysRollbackIndex. This variable must be set along with tmnxSysRollbackIndex to indicate the specific rollback file to revert. An SNMP GET request on this object should return 'notApplicable'.

OBJECT-TYPE

The value of tmnxSysRollbackResult indicates the result of the last tmnxSysRollbackStart action. none(1) None of the following apply inProgress(2) The action is still in progress success(3) The action completed successfully failed(4) The action failed interrupted (5) The action was interrupted

OBJECT-TYPE

The value of tmnxSysRollbackSave specifies whether to save the existing configuration in a rollback checkpoint file. When SET to the value of 'doAction' the system will save the configuration in a new rollback checkpoint file, with suffix '.rb'. Previously saved rollback files with the same name will increment the filename suffix by 1 up to a maximum of 9. For example, file.rb is moved to file.rb.1. The higher the number, the older the file is. An SNMP GET request on this object should return 'notApplicable'.

OBJECT-TYPE

The value of tmnxSysRollbackSaveResult indicates the result of the last tmnxSysRollbackSave action. none(1) None of the following apply inProgress(2) The action is still in progress success(3) The action completed successfully failed(4) The action failed

OBJECT-TYPE

The value of tmnxSysRollbackLocation specifies the destination filepath or file-URL where the current running configuration information will be saved when tmnxSysRollbackSave is set to 'doAction'. If the value of tmnxSysRollbackLocation is an empty string the system will attempt to store the file in the best available location locally, for example compact flash 1 or 2 if either is present.

OBJECT-TYPE

The value of tmnxSysRollbackRevertIndex indicates the last rollback checkpoint file reverted on the system.

OBJECT-TYPE

The value of tmnxSysRollbackRevertEndTime indicates the timestamp the last rollback revert on the system is completed. The value of tmnxSysRollbackRevertEndTime is affected by the value of stiPreferLocalTime.

OBJECT-TYPE

The value of tmnxSysRollbackSavedTime indicates the timestamp the last rollback save on the system is completed. The value of tmnxSysRollbackSavedTime is affected by the value of stiPreferLocalTime.

OBJECT-TYPE

The value of tmnxSysRollbackRevertStartTime indicates the timestamp the last rollback file reverted on the system is initiated. The value of tmnxSysRollbackRevertStartTime is affected by the value of stiPreferLocalTime.

OBJECT-TYPE

The value of tmnxSysRollbackRevertUserName indicates the name of a system user who initiated the last rollback revert.

OBJECT-TYPE

The value of tmnxSysRollbackRevertFilename specifies the filepath or file-URL of the last reverted rollback file.

OBJECT-TYPE

The value of the object tmnxSysRollbackSaveComment specifies a user provided comment related to the rollback checkpoint file about to be saved. It consists of any printable, seven-bit ASCII characters up to 255 characters in length.

OBJECT-TYPE

The value of tmnxSysRollbackFileDelete specifies whether to delete the rollback file specified by tmnxSysRollbackIndex. When SET to the value of 'doAction' the system will delete the rollback file specified by tmnxSysRollbackIndex. This variable must be set along with tmnxSysRollbackIndex to specify the specific rollback file to delete. An SNMP GET request on this object should return 'notApplicable'.

OBJECT-TYPE

The value of tmnxSysRollbackFileDeleteResult indicates the result of the last tmnxSysRollbackFileDelete action. none(1) None of the following apply inProgress(2) The action is still in progress success(3) The action completed successfully failed(4) The action failed

OBJECT-TYPE

The value of tmnxSysRollbackAbortRevert specifies whether to abort the rollback revert that's currently in progress. When SET to the value of 'doAction' the system will abort the active rollback revert. This will leave the system in an unknown state, so it should be used with care. An SNMP GET request on this object should return 'notApplicable'.

OBJECT-TYPE

The value of tmnxSysRollbackRescueLocation specifies the destination file path or file-URL where the rollback rescue configuration file will be saved. If the value of tmnxSysRollbackRescueLocation is an empty string the system will attempt to store the file in the best available location locally, for example compact flash 1 or 2 if either is present.

OBJECT-TYPE

The value of tmnxSysRollbackRescueRevert specifies whether to revert the rollback rescue file located in tmnxSysRollbackRescueLocation. When SET to the value of 'doAction' the system will revert the rollback rescue file. An SNMP GET request on this object should return 'notApplicable'.

OBJECT-TYPE

The value of tmnxSysRollbackRescueSave specifies whether to save the existing configuration in the rollback rescue file located in tmnxSysRollbackRescueLocation. When SET to the value of 'doAction' the system will save the configuration to the rollback rescue file. An SNMP GET request on this object should return 'notApplicable'.

OBJECT-TYPE

The value of tmnxSysRollbackRescueDelete specifies whether to delete the rollback rescue file located in tmnxSysRollbackRescueLocation. When SET to the value of 'doAction' the system will delete the rollback rescue file. An SNMP GET request on this object should return 'notApplicable'.

OBJECT-TYPE

The value of tmnxSysRollbackRescueSaveRes indicates the result of the last tmnxSysRollbackRescueSave action. none(1) None of the following apply inProgress(2) The action is still in progress success(3) The action completed successfully failed(4) The action failed

OBJECT-TYPE

The value of tmnxSysRollbackRescueRevertRes indicates the result of the last tmnxSysRollbackRescueRevert action. none(1) None of the following apply inProgress(2) The action is still in progress success(3) The action completed successfully failed(4) The action failed interrupted (5) The action was interrupted

OBJECT-TYPE

The value of tmnxSysRollbackRescueDeleteRes indicates the result of the last tmnxSysRollbackRescueDelete action. none(1) None of the following apply inProgress(2) The action is still in progress success(3) The action completed successfully failed(4) The action failed

OBJECT-TYPE

The value of tmnxSysRollbackRescueSavedTime indicates the timestamp the last rollback rescue save on the system is completed. The value of tmnxSysRollbackRescueSavedTime is affected by the value of stiPreferLocalTime.

OBJECT-TYPE

The value of tmnxSysRollbackRescueRevStTime indicates the timestamp the last rescue rollback file reverted on the system is initiated. The value of tmnxSysRollbackRescueRevStTime is affected by the value of stiPreferLocalTime.

OBJECT-TYPE

The value of tmnxSysRollbackRescueRevEdTime indicates the timestamp the last rollback rescue revert on the system is completed. The value of tmnxSysRollbackRescueRevEdTime is affected by the value of stiPreferLocalTime.

OBJECT-TYPE

The value of tmnxSysRollbackRescueRevUser indicates the name of a system user who initiated the last rollback rescue revert.

OBJECT-TYPE

The value of the object tmnxSysRollbackRescueSaveComment specifies a user provided comment related to the rollback rescue file about to be saved. It consists of any printable, seven-bit ASCII characters up to 255 characters in length.

OBJECT-TYPE

The value of tmnxSysRollbackRescueAbortRevert specifies whether to abort the rescue revert that's currently in progress. When SET to the value of 'doAction' the system will abort the active rollback revert. This will leave the system in an unknown state, so it should be used with care. An SNMP GET request on this object should return 'notApplicable'.

OBJECT-TYPE

The value of tmnxSysRollbackRescueFileExists indicates whether a rollback rescue file specified by tmnxSysRollbackRescueLocation and suffix '.rc' is present. A value of 'true' indicates the file is present and a value of 'false' indicates the file is not present.

OBJECT-TYPE

The value of tmnxSysRollbackMaxLocalFiles specifies the maximum number of rollback checkpoint files that can be saved locally on the compact flash.

OBJECT-TYPE

The value of tmnxSysRollbackMaxRemoteFiles specifies the maximum number of rollback checkpoint files that can be saved at a remote ftp location.

OBJECT-TYPE

The value of tmnxSysRollbackTableLastChanged indicates the timestamp of the last configuration changes to any of the rows in tmnxSysRollbackFileTable.

OBJECT-TYPE

The table tmnxSysRollbackFileTable contains information pertaining to an entry for each rollback checkpoint file. If the configured rollback location as specified by tmnxSysRollbackLocation is on compact flash, this table can have up to a maximum of tmnxSysRollbackMaxLocalFiles. If the configured rollback location as specified by tmnxSysRollbackLocation is a remote ftp location, this table can have up to a maximum of tmnxSysRollbackMaxRemoteFiles.

OBJECT-TYPE

Each row entry contains information about a rollback checkpoint file.

OBJECT-TYPE

The value of tmnxSysRollbackFileIndex specifies the index of the rollback checkpoint file.

OBJECT-TYPE

The value of tmnxSysRollbackFileCreationTime indicates the timestamp of the creation time of this row in tmnxSysRollbackFileTable. The value of tmnxSysRollbackFileCreationTime is affected by the value of stiPreferLocalTime.

OBJECT-TYPE

The value of the object tmnxSysRollbackFileComment specifies a user provided comment related to a rollback checkpoint file. It consists of any printable, seven-bit ASCII characters up to 255 characters in length.

OBJECT-TYPE

The value of tmnxSysRollbackFileUserName indicates the name of a system user who saves this rollback file.

OBJECT-TYPE

The value of tmnxSysRollbackFileVersion indicates the version number of the software running on the system when the rollback file is saved.

OBJECT-IDENTITY

OBJECT-TYPE

This object gives the currently active (booted) value of li-separate. This value specifies whether or not a non-LI user has access to Lawful Intercept (LI) information. When sbbiLiSeparate has a value of 'true', a user who does not have the TIMETRA-SECURITY-MIB:: tmnxUserAccess 'li' bit set will not be allowed to access CLI or SNMP objects in the 'li' context.

OBJECT-TYPE

This object gives the currently active (booted) value of li-local-save. This value specifies whether or not Lawful Intercept (LI) configuration is allowed to be save to a local file.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

The value of tmnxSysCandidateCfgState indicates the current state of the global candidate config. A value of 'unmodified(0)' indicates nobody has entered the candidate config since boot or the last commit/discard. A value of 'modified(1)' indicates there are uncommitted changes in the candidate config. A value of 'unconfirmed(2)' indicates there are no uncommitted changes in the candidate config but the result of the last commit will be auto-reverted unless it is confirmed before the timeout expires.

OBJECT-TYPE

The value of tmnxSysCandidateCfgEditors indicates the current amount of users that are editing or reading the candidate config.

OBJECT-TYPE

The value of tmnxSysCandidateCfgCommitState indicates the result of the last commit performed in the global candidate config. A value of 'none(0)' indicates there have been no commits since the last reboot of the node. A value of 'in-progress(1)' indicates the system is currently committing the candidate config. A value of 'success(2)' indicates the last commit finished successfully. A value of 'revert-pending(3)' indicates the last commit finished successfully but has not been confirmed yet, and will be auto-reverted if it is not confirmed before the time specified in tmnxSysCandidateCfgRevertTime. A value of 'failed(4)' indicates the last commit failed and has been undone. A value of 'revert-in-progress(5)' indicates the last commit finished successfully but was not confirmed in time and is currently being reverted. A value of 'reverted(6)' indicates the last commit finished successfully but was not confirmed in time and has been reverted. A value of 'revert-failed(7)' indicates the last commit finished successfully but was not confirmed in time and the system attempted to revert it but failed.

OBJECT-TYPE

The value of tmnxSysCandidateCfgCommitTime indicates the date and time the last (attempted) commit of the candidate config was started.

OBJECT-TYPE

The value of tmnxSysCandidateCfgRevertTime indicates the date and time the system will automatically revert the last committed candidate config, unless they are confirmed. If this date and time is in the past it indicates the candidate config was not confirmed and has been reverted. If no auto-revert was requested at the time of the commit the value of this field will be set to zero.

OBJECT-TYPE

The value of tmnxSysCandidateCfgChckptCreated indicates if a checkpoint was created after the last commit of the candidate config.

OBJECT-TYPE

The value of tmnxSysCandidateCfgUser indicates the name of a system user who initiated the last commit of the candidate config.

OBJECT-TYPE

The value of tmnxSysCandidateCfgExclusiveUsr indicates the name of a system user who is currently exclusively modifying the candidate config. This indicates no other user can modify the candidate config until this system user has finished modifying the candidate config. If this field is empty no user has requested to exclusively modify the candidate config.

OBJECT-IDENTITY

OBJECT-TYPE

The value of tmnxSysNetconfAdminStatus specifies the desired administrative state of the NETCONF daemon. When tmnxSysNetconfAdminStatus is set to 'inService', the NETCONF daemon will begin receiving NETCONF requests from external NETCONF users. When tmnxSysNetconfAdminStatus is set to 'outOfService', the NETCONF daemon is suspended and will no longer receive NETCONF requests from external NETCONF users.

OBJECT-TYPE

The value of tmnxSysNetconfOperStatus indicates the state of the NETCONF daemon. A value of 'inService' indicates that the NETCONF daemon will receive NETCONF requests from external NETCONF users. A value of 'outOfService' indicates that the NETCONF daemon is suspended and will no longer receive NETCONF requests from external NETCONF users.

OBJECT-TYPE

The value of tmnxSysNetconfRequests indicates the total number of NETCONF requests which have been accepted and processed by the NETCONF server.

OBJECT-TYPE

The value of tmnxSysNetconfGetRequests indicates the total number of get NETCONF requests which have been accepted and processed by the NETCONF server.

OBJECT-TYPE

The value of tmnxSysNetconfGetConfigRequests indicates the total number of get-config NETCONF requests which have been accepted and processed by the NETCONF server.

OBJECT-TYPE

The value of tmnxSysNetconfEditConfigRequests indicates the total number of edit-config NETCONF requests which have been accepted and processed by the NETCONF server.

OBJECT-TYPE

The value of tmnxSysNetconfCloseRequests indicates the total number of close-session NETCONF requests which have been accepted and processed by the NETCONF server.

OBJECT-TYPE

The value of tmnxSysNetconfKillRequests indicates the total number of kill-session NETCONF requests which have been accepted and processed by the NETCONF server.

OBJECT-TYPE

The value of tmnxSysNetconfResponses indicates the total number of NETCONF responses which have been generated and sent by the NETCONF server.

OBJECT-TYPE

The value of tmnxSysNetconfErrorResponses indicates the total number of NETCONF error responses which have been generated and sent by the NETCONF server.

OBJECT-TYPE

The value of tmnxSysNetconfCopyConfigRequests indicates the total number of copy-config NETCONF requests which have been accepted and processed by the NETCONF server.

OBJECT-TYPE

The value of tmnxSysNetconfDelConfigRequests indicates the total number of delete-config NETCONF requests which have been accepted and processed by the NETCONF server.

OBJECT-TYPE

The value of tmnxSysNetconfValidateRequests indicates the total number of validate NETCONF requests which have been accepted and processed by the NETCONF server.

OBJECT-TYPE

The value of tmnxSysNetconfFailedEditCfgReqs indicates the total number of edit-config NETCONF requests which have failed because of locks taken by other NETCONF sessions.

OBJECT-TYPE

The value of tmnxSysNetconfFailedLockReqs indicates the total number of lock NETCONF requests which have failed because of locks taken by other NETCONF sessions.

OBJECT-TYPE

The value of tmnxSysNetconfLockRequests indicates the total number of lock NETCONF requests which have been accepted and processed by the NETCONF server.

OBJECT-TYPE

The value of tmnxSysNetconfUnlockRequests indicates the total number of unlock NETCONF requests which have been accepted and processed by the NETCONF server.

OBJECT-TYPE

The value of tmnxSysNetconfCommitRequests indicates the total number of commit NETCONF requests which have been accepted and processed by the NETCONF server.

OBJECT-TYPE

The value of tmnxSysNetconfDiscardRequests indicates the total number of discard change NETCONF requests which have been accepted and processed by the NETCONF server.

OBJECT-TYPE

The value of tmnxSysNetconfCapCandidateCfg specifies whether or not the candidate datastore is supported by the NETCONF server. When set to 'true', the NETCONF server allows access to the candidate datastore.

OBJECT-TYPE

The value of tmnxSysNetconfCapRunningCfg specifies whether or not the writable running datastore is supported by the NETCONF server. When set to 'true', the NETCONF server allows access to the writable running datastore.

OBJECT-TYPE

The value of tmnxSysNetconfYangBaseR13 specifies whether or not the base release 13 Yang models are supported by the NETCONF server. When set to 'true', the NETCONF server allows access to base release 13 Yang models. This object was made obsolete in the 15.1 release.

OBJECT-TYPE

The value of tmnxSysNetconfYangNokia specifies whether or not the Nokia Yang models are supported by the NETCONF server. When set to 'true', the NETCONF server allows access to the Nokia Yang models. This object was made obsolete in the 15.1 release.

OBJECT-TYPE

The value of tmnxSysNetconfCreateSubRequests indicates the total number of create subscription NETCONF requests which have been accepted and processed by the NETCONF server.

OBJECT-TYPE

The value of tmnxSysNetconfAutoCfgSave specifies whether the running configuration is saved as part of a commit operation initiated from Netconf.

OBJECT-TYPE

The value of tmnxSysNetconfPort specifies port on which is NETCONF server listening for connections.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

The value of tmnxSysStrmAdminStatus specifies the desired administrative state of the proprietary protocol streaming server daemon. When tmnxSysStrmAdminStatus is set to 'inService', the streaming server daemon accepts and processes requests from the Nokia 5620 Service Aware Manager (SAM) system. When tmnxSysStrmAdminStatus is set to 'outOfService', the streaming server daemon is suspended and will no longer accept requests from the SAM system.

OBJECT-TYPE

The value of tmnxSysStrmDumpSnmpRequests indicates the total number of streaming snmp dump request PDUs which have been accepted and processed by the Nokia 5620 Service Aware Manager (SAM) streaming protocol entity.

OBJECT-TYPE

The value of tmnxSysStrmGetManyRequests indicates the total number of streaming get many request PDUs which have been accepted and processed by the Nokia 5620 Service Aware Manager (SAM) streaming protocol entity.

OBJECT-TYPE

The value of tmnxSysStrmResponses indicates the total number of streaming response PDUs which have been generated by the Nokia 5620 Service Aware Manager (SAM) streaming protocol entity.

OBJECT-IDENTITY

OBJECT-TYPE

The tmnxSysXmppServerTable contains information pertaining to an entry for each server. Row entries are created and deleted by the agent.

OBJECT-TYPE

Each row entry contains information about a XMPP server.

OBJECT-TYPE

The value of tmnxSysXmppServName indicates the name associated with the XMPP Server.

OBJECT-TYPE

The value of tmnxSysXmppServFQDN specifies the Fully Qualified Domain Name (FQDN) associated with the XMPP Server.

OBJECT-TYPE

The value of tmnxSysXmppServRowStatus specifies the row status. It is used to create and delete row entries in this table.

OBJECT-TYPE

The value of tmnxSysXmppServUserName specifies the username that is used in the XMPP server access requests. When no username is not provided, the chassis MAC is used as the default user name.

OBJECT-TYPE

The value of tmnxSysXmppServPassword specifies the password that is used in the XMPP server access requests.

OBJECT-TYPE

The value of tmnxSysXmppServLastChanged indicates the timestamp of last change to this row in tmnxSysXmppServerTable.

OBJECT-TYPE

The tmnxSysXmppServUptime indicates the uptime of the XMPP server.

OBJECT-TYPE

The value of tmnxSysXmppServIQSent indicates the number of XMPP Info/Query message sent.

OBJECT-TYPE

The value of tmnxSysXmppServIQRcvd indicates the number of XMPP Info/Query message received.

OBJECT-TYPE

The value of tmnxSysXmppServIQError indicates the number of XMPP Info/Query error messages received.

OBJECT-TYPE

The value of tmnxSysXmppServIQTimedOut indicates the number of XMPP Info/Query messages timed out.

OBJECT-TYPE

The value of tmnxSysXmppServIQAckRcvd indicates the number of XMPP Info/Query acknowledgement messages received.

OBJECT-TYPE

The value of tmnxSysXmppServIQMinRtt indicates the XMPP Info/Query minimum round trip time.

OBJECT-TYPE

The value of tmnxSysXmppServIQMaxRtt indicates the XMPP Info/Query maximum round trip time.

OBJECT-TYPE

The value of tmnxSysXmppServVsdUpdatesRcvd indicates the number of VSD updates received by the XMPP server.

OBJECT-TYPE

The value of tmnxSysXmppServUpdatesRcvd indicates the number of nuage updates received by the XMPP server.

OBJECT-TYPE

The value of tmnxSysXmppServMsgSent indicates the number of messages sent from the XMPP server.

OBJECT-TYPE

The value of tmnxSysXmppServMsgRcvd indicates the number of messages received from the XMPP server.

OBJECT-TYPE

The value of tmnxSysXmppServMsgAckRcvd indicates the number of message acknowledgements received from the XMPP server.

OBJECT-TYPE

The value of tmnxSysXmppServMsgError indicates the number of error messages received from the XMPP server.

OBJECT-TYPE

The value of tmnxSysXmppServMsgTimedOut indicates the number of timeout messages received from the XMPP server.

OBJECT-TYPE

The value of tmnxSysXmppServMsgMinRtt indicates the minimum message round trip time from the XMPP server.

OBJECT-TYPE

The value of tmnxSysXmppServMsgMaxRtt indicates the maximum message round trip time from the XMPP server.

OBJECT-TYPE

The value of tmnxSysXmppServSubSent indicates the number of subscriptions sent from the XMPP server.

OBJECT-TYPE

The value of tmnxSysXmppServUnSubSent indicates the number of unsubscriptions sent from the XMPP server.

OBJECT-TYPE

The value of tmnxSysXmppServState indicates the state of the XMPP server.

OBJECT-TYPE

The value of tmnxSysXmppServAdminState specifies the administrative state of the XMPP server.

OBJECT-TYPE

The value of tmnxSysXmppServOperUserName indicates the operational user name that is used in the XMPP server access requests. When no user name is not provided, the chassis MAC is used as the default user name.

OBJECT-TYPE

The value of tmnxSysXmppServAuthType indicates the authentication type that is used in the XMPP server access requests.

OBJECT-TYPE

The value of tmnxSysXmppServConnMode indicates the connection type that is used in the XMPP server access requests.

OBJECT-TYPE

The tmnxSysXmppServServiceId specifies the routing context which provides reachability to the DNS and XMPP servers configured. When tmnxSysXmppServRouterId is non-zero, tmnxSysXmppServServiceId must be zero and vice versa.

OBJECT-TYPE

The tmnxSysXmppServRouterId specifies the routing context that provides reachability to the DNS and XMPP servers configured. When tmnxSysXmppServRouterId is non-zero, tmnxSysXmppServServiceId must be zero and vice versa.

OBJECT-TYPE

The tmnxSysVsdServerTable contains information pertaining to an entry for each server.

OBJECT-TYPE

Each row entry contains information about a VSwitch Controller VSD server.

OBJECT-TYPE

The value of tmnxSysVsdServerInstance specifies an instance of a VSwitch Controller VSD server. The instance Id is an internally generated number that is unique for a given VSD server.

OBJECT-TYPE

The value of tmnxSysVsdServUptime indicates the timestamp of the uptime of each VSD server entry in tmnxSysXmppServerTable.

OBJECT-TYPE

The value of tmnxSysVsdServUserName specifies the VSD username.

OBJECT-TYPE

The value of tmnxSysVsdServerStatus indicates the status of the VSD server.

OBJECT-TYPE

The value of tmnxSysVsdServMsgSent indicates the number of messages sent from the VSD server.

OBJECT-TYPE

The value of tmnxSysVsdServMsgRcvd indicates the number of messages received from the VSD server.

OBJECT-TYPE

The value of tmnxSysVsdServMsgAckRcvd indicates the number of message acknowledgements received from the VSD server.

OBJECT-TYPE

The value of tmnxSysVsdServMsgError indicates the number of error messages received from the VSD server.

OBJECT-TYPE

The value of tmnxSysVsdServMsgTimedOut indicates the number of timeout messages received from the VSD server.

OBJECT-TYPE

The value of tmnxSysVsdServMsgMinRtt indicates the minimum message round trip time from the VSD server.

OBJECT-TYPE

The value of tmnxSysVsdServMsgMaxRtt indicates the maximum message round trip time from the VSD server.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

The tmnxCardCpuResMonitorTable details the specified current card's CPU resources. The information described in this table is volatile and dependent on the current environmental conditions, and specified sample-time. Information is only displayed for online cards.

OBJECT-TYPE

The tmnxCardCpuResMonitorEntry contains the card level CPU monitoring statistics over a specified sample-time.

OBJECT-TYPE

The value of tmnxCardResourceSlotNum specifies the slot number of the card to which the resource information is monitored.

OBJECT-TYPE

The value of tmnxCardCpuResSampleTime specifies the sample-time used to calculate the utilization results for the row.

OBJECT-TYPE

The value of tmnxCardCpuResMonCpuIdle indicates the overall percentage of CPU idleness over the specified sample-time.

OBJECT-TYPE

The value of tmnxCardCpuResMonBusyCoreUtil indicates the utilization percentage of the busiest processor core over the specified sample-time. On single core CPUs, this is the overall system utilization percentage over the specified sample-time.

OBJECT-TYPE

The value of tmnxCardCpuResMonBusyGroupName indicates the name of the group that is running at the highest capacity utilization. Capacity utilization is the CPU utilization relative to the maximum CPU resources available to that group. A group is a set of related applications, services, tasks or protocol handlers that consumes some part of the system CPU resources. The capacity utilization of the busiest group is indicated by tmnxCardCpuResMonBusyGroupUtil.

OBJECT-TYPE

The value of tmnxCardCpuResMonBusyGroupUtil indicates the capacity utilization of the group that is running at the highest capacity utilization. Capacity utilization is the CPU utilization relative to the maximum CPU resources available to that group. A group is a set of related applications, services, tasks or protocol handlers that consumes some part of the system CPU resources. The name of the busiest group is indicated by tmnxCardCpuResMonBusyGroupName.

OBJECT-TYPE

The tmnxCardMemResMonitorTable details the specified current card's memory resources. The information described in this table is volatile and dependent on the current environmental conditions. Information is only displayed for online cards.

OBJECT-TYPE

The tmnxCardMemResMonitorEntry contains the card's memory usage statistics.

OBJECT-TYPE

The value of tmnxCardMemResMemoryUsed indicates the total pre-allocated pool memory, in kilobytes, currently in use on the card.

OBJECT-TYPE

The value of tmnxCardMemResMemoryAvailable indicates the amount of free memory, in kilobytes, in the card that is not allocated to memory pools, but is available in case a memory pool needs to grow.

OBJECT-TYPE

The value of tmnxCardMemResPoolsAllocated indicates the total memory, in kilobytes, currently allocated in memory-pools on the card. This memory may or may not be currently in use, but is pre-allocated should the software need to use it.

OBJECT-IDENTITY

OBJECT-TYPE

The tmnxSysResEcmpProfTable contains information about the system resource profile to be allocated for each type of the ecmp bundle. The table can have up to a maximum of 2 entries.

OBJECT-TYPE

Each row entry contains information about the resources to be created for each type of ecmp bundle supported. Entries in this table can be created and deleted via SNMP SET operations to tmnxSysResEcmpProfRowStatus.

OBJECT-TYPE

The value of tmnxSysResEcmpProfId specifies the resource profile index for the ecmp bundle.

OBJECT-TYPE

The value of the tmnxSysResEcmpProfRowStatus specifies the status of this row. It allows the creation and deletion of row entries in tmnxSysResEcmpProfTable. To create a row in this table, set tmnxSysResEcmpProfRowStatus to createAndGo(4). The values of tmnxSysResEcmpProfType, tmnxSysResEcmpProfLinksPerGrp, and tmnxSysResEcmpProfNumGrps must also be set to valid values for the row creation to succeed. To delete a row in this table, set tmnxSysResEcmpProfRowStatus to delete(6).

OBJECT-TYPE

The value of tmnxSysResEcmpProfType specifies the ecmp bundle type applicable to this conceptual row.

OBJECT-TYPE

The value of tmnxSysResEcmpProfLinksPerGrp specifies the maximum number of links per group for the ecmp bundle

OBJECT-TYPE

The value of tmnxSysResEcmpProfNumGrps specifies the maximum number of ecmp groups allowed for the ecmp bundle. When tmnxSysResEcmpProfType is 'mpls', maximum value of tmnxSysResEcmpProfNumGrps is 2047, Only when tmnxSysResEcmpProfType is 'ip', can the maximum value of tmnxSysResEcmpProfNumGrps be 2048.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

The value of tmnxSysResItCamBankV6Multicast specifies the maximum number of internal TCAM banks to support ipv6 multicast to scale

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

The value of tmnxSysFpCamAllocAdmnV6Multicast specifies the maximum number of number of IPv6 multicast routes allowed to be installed in the system/FP

OBJECT-TYPE

The value of tmnxSysFpCamAllocOperV6Multicast specifies the total number of IPv6 multicast routes installed in the system/FP

OBJECT-IDENTITY

OBJECT-TYPE

The value of tmnxSysDhcp6AdvNoaddrsGlobal specifies the composition of DHCPv6 Advertise Messages in case a DHCP6 application in this system will not assign any addresses to any Identity Association (IA) in a subsequent Request from the client. DHCP6 applications in this system are Relay, Server, Enhanced Subscriber Management (ESM) Proxy and ESM Relay. By default, a DHCP6 application in this system will send an Advertise message to the client that includes the IA containing a Status Code option with status code 'NoAddrsAvail', as specified in Errata 2472. If the bit corresponding to a DHCP6 application is set, that application will send an Advertise message to the client that includes only a Status Code option with code 'NoAddrsAvail'. This system will refuse bit combinations that are not supported: the 'esmRelay' and 'server' bits must be toggled together, and the 'esmProxy' and 'relay' bits are read-only.

OBJECT-IDENTITY

OBJECT-TYPE

The value of tmnxSysVsdSystemId specifies the name used by this system as its identity when communicating with VSD.

OBJECT-TYPE

The value of tmnxSysVsdGwPubSubIsSubscrd indicates whether the system is subscribed to the gateway publish-subscribe node.

OBJECT-TYPE

The value of tmnxSysVsdGwPubSubNodeName indicates the gateway publish-subscribe node name assigned by VSD.

OBJECT-TYPE

The value of tmnxSysVsdGwPubSubLstSubscrdTime indicates the last subscription time to the gateway publish-subscribe node.

OBJECT-TYPE

The value of tmnxSysVsdGwLastAuditTxTime indicates the time last gateway audit was sent to the VSD.

OBJECT-IDENTITY

OBJECT-TYPE

The value of tmnxSysLicenseStatus indicates the current status of the license.

OBJECT-TYPE

The value of tmnxSysLicenseName indicates the license name.

OBJECT-TYPE

The value of tmnxSysLicenseUuid indicates the Universally Unique Identifier (UUID) for the license of the virtual machine (VM).

OBJECT-TYPE

The value of tmnxSysLicenseDescription indicates the license description.

OBJECT-TYPE

The value of tmnxSysLicenseProduct indicates the product for which the license is valid.

OBJECT-TYPE

The value of tmnxSysLicenseSwVersion indicates the SROS series system software version for which the license is valid.

OBJECT-TYPE

The value of tmnxSysLicenseIssueDateAndTime indicates the day and time the license was issued.

OBJECT-TYPE

The value of tmnxSysLicenseStartDateAndTime indicates the day and time the license became active.

OBJECT-TYPE

The value of tmnxSysLicenseEndDateAndTime indicates the day and time the license expires.

OBJECT-TYPE

The value of tmnxSysLicenseVChassisType indicates the virtual chassis type for which the license is valid. A value of empty string indicates that the license is not associated with a virtual chassis.

OBJECT-TYPE

The value of tmnxSysLicenseMaxNumCPMs indicates the maximum number of CPMs allowed by the license. A value of 0 indicates that the number of CPMs is not restricted by the license.

OBJECT-TYPE

The value of tmnxSysLicenseMaxNumIOMs indicates the maximum number of IOMs allowed by the license. A value of 0 indicates that the number of IOMs is not restricted by the license.

OBJECT-TYPE

The tmnxSysCpmCardLicenseTable has an entry for each CPM card in the first chassis in the system.

OBJECT-TYPE

Each row represents a CPM card in the first chassis in the system. When a tmnxChassisEntry is created, a tmnxSysCpmCardLicenseEntry is created for each CPM card in the first chassis. Entries cannot be created or deleted via SNMP SET operations.

OBJECT-TYPE

The value of tmnxSysCpmCardLicStatus indicates the current status of the license.

OBJECT-TYPE

The value of tmnxSysCpmCardLicName indicates the license name.

OBJECT-TYPE

The value of tmnxSysCpmCardLicUuid indicates the Universally Unique Identifier (UUID) for the license of the CPM card in the virtual machine (VM).

OBJECT-TYPE

The value of tmnxSysCpmCardLicDescription indicates the license description.

OBJECT-TYPE

The value of tmnxSysCpmCardLicProduct indicates the product for which the license is valid.

OBJECT-TYPE

The value of tmnxSysCpmCardLicSwVersion indicates the SROS series system software version for which the license is valid.

OBJECT-TYPE

The value of tmnxSysCpmCardLicIssueDateTime indicates the day and time the license was issued.

OBJECT-TYPE

The value of tmnxSysCpmCardLicStartDateTime indicates the day and time the license became active.

OBJECT-TYPE

The value of tmnxSysCpmCardLicEndDateTime indicates the day and time the license expires.

OBJECT-TYPE

The value of tmnxSysCpmCardLicVChassisType indicates the virtual chassis type for which the license is valid. A value of empty string indicates that the license is not associated with a virtual chassis.

OBJECT-TYPE

The value of tmnxSysCpmCardLicMaxNumCPMs indicates the maximum number of CPMs allowed by the license. A value of 0 indicates that the number of CPMs is not restricted by the license.

OBJECT-TYPE

The value of tmnxSysCpmCardLicMaxNumIOMs indicates the maximum number of IOMs allowed by the license. A value of 0 indicates that the number of IOMs is not restricted by the license.

OBJECT-TYPE

The tmnxSysCpmCardLicFeatureTable has an entry for each feature supported by the license installed on a CPM card in the chassis with TIMETRA-CHASSIS-MIB::tmnxPhysChassisClass 'routerChassis(3)' and TIMETRA-CHASSIS-MIB::tmnxPhysChassisNum '1'.

OBJECT-TYPE

When a TIMETRA-CHASSIS-MIB::tmnxCpmCardEntry is created for a CPM card in the chassis with TIMETRA-CHASSIS-MIB::tmnxPhysChassisClass 'routerChassis(3)' and TIMETRA-CHASSIS-MIB::tmnxPhysChassisNum '1', a tmnxSysCpmCardLicFeatureEntry is created for each feature supported by the license installed on that CPM card. Entries cannot be created or deleted via SNMP SET operations.

OBJECT-TYPE

The value of tmnxSysCpmCardLicFeatApplication specifies the application supported by the license.

OBJECT-TYPE

The value of tmnxSysCpmCardLicFeatNumber specifies the feature number associated with the feature supported by the license.

OBJECT-TYPE

The value of tmnxSysCpmCardLicFeatDescription indicates the description of the feature supported by the license.

OBJECT-TYPE

The tmnxSysLicensingTable an entry for each licensed applications for this system.

OBJECT-TYPE

Each row contains detailed information about each licensed application. Entries cannot be created or deleted via SNMP SET operations.

OBJECT-TYPE

The value of tmnxSysLicensingGroup indicates the licensing group.

OBJECT-TYPE

The value of tmnxSysLicensedAppName indicates the name of the licensed application.

OBJECT-TYPE

The value of the object tmnxSysAppLicenseDescription indicates a more detailed description of the application license.

OBJECT-TYPE

The value of tmnxSysAppLicenseType specifies the type of licensing done for this application. pool - A pool license grants a specified number of concurrent allocations of the license. rtu - An RTU license grants the right to use a feature

OBJECT-TYPE

The value of tmnxSysAppLicensePoolSize indicates the size of the pool of licenses that can be allocated within the system. A value of (-1) indicates a pool size is not applicable to this application based on tmnxSysAppLicenseType.

OBJECT-TYPE

The value of tmnxSysAppLicenseAllocated indicates the the number of these licenses currently allocated in the system.

OBJECT-TYPE

The value of tmnxSysAppLicensePresent specifies if the current system license grants the right to use feature on this system.

OBJECT-TYPE

The value of tmnxSysAppLicenseState indicates the state of the license for this application. valid - No issue with application license error - Insufficient licensing has been detected. violation - License violation has been detected.

OBJECT-TYPE

The tmnxSysAvailableLicensesTable has an entry for each license available for this system that was matched in the license file.

OBJECT-TYPE

Each row represents a license avalalable for this system from the last loaded license-file.

OBJECT-TYPE

The value of tmnxSysAvailLicenseIndex indicates the index of the matched license.

OBJECT-TYPE

The value of tmnxSysAvailLicenseName indicates the license name.

OBJECT-TYPE

The value of tmnxSysAvailLicenseUuid indicates the Universally Unique Identifier (UUID) for the license.

OBJECT-TYPE

The value of tmnxSysAvailLicenseDescription indicates the license description.

OBJECT-TYPE

The value of tmnxSysAvailLicenseSwVersion indicates the SROS series system software version for which the license is valid.

OBJECT-TYPE

The value of tmnxSysAvailLicIssueDateTime indicates the day and time the license was issued.

OBJECT-TYPE

The value of tmnxSysAvailLicStartDateTime indicates the day and time the license becomes active.

OBJECT-TYPE

The value of tmnxSysAvailLicEndDateTime indicates the day and time the license expires.

OBJECT-TYPE

The value of tmnxSysAvailLicenseProduct indicates the licensed product.

OBJECT-TYPE

The value of tmnxSysLicensingState indicates the current status of the system licensing.

OBJECT-TYPE

The value of tmnxSysLicensingRebootPending indicates whether a system reboot is pending due to system licensing

OBJECT-IDENTITY

OBJECT-TYPE

The tmnxSysAppStats24HrsTable contains statistics about a virtual machine application collected periodically during the last 24 hours.

OBJECT-TYPE

Each conceptual row contains a specific instance of a statistics value at a specific time.

OBJECT-TYPE

The value of tmnxSysAppStats24HrsApplication indicates the application.

OBJECT-TYPE

The value of tmnxSysAppStats24HrsType indicates the meaning of the statistics in this conceptual row.

OBJECT-TYPE

The value of tmnxSysAppStats24HrsIndex is a numerical index value generated by this system.

OBJECT-TYPE

The value of the object tmnxSysAppStats24HrsName indicates the human-readable identifier of the statistics contained in this conceptual row.

OBJECT-TYPE

The value of the object tmnxSysAppStats24HrsValue indicates the value of the statistics contained in this conceptual row.

OBJECT-TYPE

The value of the object tmnxSysAppStats24HrsTime indicates the time the system measured the value of tmnxSysAppStats24HrsValue.

OBJECT-TYPE

The tmnxSysAppStatsWeekTable contains statistics about a virtual machine application collected periodically during the last week.

OBJECT-TYPE

Each conceptual row contains a specific instance of a statistics value associated with a specific 24 hours period.

OBJECT-TYPE

The value of tmnxSysAppStatsWeekApplication indicates the application.

OBJECT-TYPE

The value of tmnxSysAppStatsWeekType indicates the meaning of the statistics in this conceptual row.

OBJECT-TYPE

The value of tmnxSysAppStatsWeekIndex is a numerical index value generated by this system.

OBJECT-TYPE

The value of the object tmnxSysAppStatsWeekName indicates the human-readable identifier of the statistics contained in this conceptual row.

OBJECT-TYPE

The value of the object tmnxSysAppStatsWeekAverage indicates the average value of the statistics contained in this conceptual row for this period of 24 hours.

OBJECT-TYPE

The value of the object tmnxSysAppStatsWeekPeak indicates the peak value of the statistics contained in this conceptual row for this period of 24 hours.

OBJECT-TYPE

The value of the object tmnxSysAppStatsWeekTime indicates the time the system determined the values of tmnxSysAppStatsWeekAverage and tmnxSysAppStatsWeekPeak.

OBJECT-TYPE

The tmnxSysAppStatsPeakTable contains peak values of statistics about a virtual machine application.

OBJECT-TYPE

Each conceptual row contains a peak value of a statistic about a virtual machine application.

OBJECT-TYPE

The value of tmnxSysAppStatsPeakApplication indicates the application.

OBJECT-TYPE

The value of tmnxSysAppStatsPeakType indicates the meaning of the statistics in this conceptual row.

OBJECT-TYPE

The value of the object tmnxSysAppStatsPeakName indicates the human-readable identifier of the statistics contained in this conceptual row.

OBJECT-TYPE

The value of the object tmnxSysAppStatsPeakValue indicates the value of the statistics contained in this conceptual row.

OBJECT-TYPE

The value of the object tmnxSysAppStatsPeakTime indicates the time the system measured the value of tmnxSysAppStatsPeakValue.

OBJECT-TYPE

The tmnxSysAppStats48HrsTable contains statistics about a virtual machine application collected periodically 24 to 48 hours ago.

OBJECT-TYPE

Each conceptual row contains a specific instance of a statistics value at a specific time.

OBJECT-TYPE

The value of tmnxSysAppStats48HrsApplication indicates the application.

OBJECT-TYPE

The value of tmnxSysAppStats48HrsType indicates the meaning of the statistics in this conceptual row.

OBJECT-TYPE

The value of tmnxSysAppStats48HrsIndex is a numerical index value generated by this system.

OBJECT-TYPE

The value of the object tmnxSysAppStats48HrsName indicates the human-readable identifier of the statistics contained in this conceptual row.

OBJECT-TYPE

The value of the object tmnxSysAppStats48HrsValue indicates the value of the statistics contained in this conceptual row.

OBJECT-TYPE

The value of the object tmnxSysAppStats48HrsTime indicates the time the system measured the value of tmnxSysAppStats48HrsValue.

OBJECT-TYPE

The value of tmnxSysLicensingProduct indicates the type of license expected based on the running system.

OBJECT-TYPE

The value of tmnxSysLicensingUuid indicates the Universally Unique Identifier (UUID) being used to match license.

OBJECT-IDENTITY

OBJECT-TYPE

The value of tmnxSysFibSelective specifies whether selective FIB is enabled in the system. If the value of tmnxSysFibSelective is set to false, then all active routes are installed on all line cards. If the value of tmnxSysFibSelective is set to true, then a line card installs a particular IP route only if that route is relevant to the card based on the current configuration of interfaces and services.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

The value of tmnxSysSnmpSrcAccessTblLstChgd indicates the sysUpTime at the time of the last modification to tmnxSysSnmpSrcAccessLstTable by adding, deleting an entry or change to a writable object in the table. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The tmnxSysSnmpSrcAccessLstTable contains objects for creating entries corresponding to source access list.

OBJECT-TYPE

The tmnxSysSnmpSrcAccessLstEntry contains configuration items for creating src-access-list.

OBJECT-TYPE

The value of tmnxSysSnmpSrcAccessLstName specifies the name given to this src-access-list.

OBJECT-TYPE

The value of tmnxSysSnmpSrcAccessLstRowStatus specifies the row status used for creation and deletion of src-access-list entries.

OBJECT-TYPE

The value of tmnxSysSnmpSrcAccessLstLastChg indicates the sysUpTime at the time of the last modification of this row. If no changes were made to the row since the last re-initialization of the local network management subsystem, then this object contains the value zero.

OBJECT-IDENTITY

OBJECT-TYPE

The tmnxSysSnmpCommunityStatsTable contains statistics for SNMP Community.

OBJECT-TYPE

Each row entry represents a collection of statistics for each SNMP Community within a virtual router. Entries cannot be created and deleted via SNMP SET operations.

OBJECT-TYPE

The value of tmnxSysSnmpCommunityPktDropped indicates the total number of packets dropped when a SNMP GET request has been made.

OBJECT-IDENTITY

OBJECT-TYPE

The value of tmnxSysMgmtProtocolTblLstChng indicates the sysUpTime at the time of the last modification to tmnxSysMgmtProtocolTable by change to a writable object in the table. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The tmnxSysMgmtProtocolTable contains objects for managing the capabilities of the different network management protocols.

OBJECT-TYPE

The tmnxSysMgmtProtocolEntry contains configuration items for managing the different network management protocols. Entries in this table cannot be created or deleted.

OBJECT-TYPE

The value of tmnxSysMgmtProtocol specifies the name of the network management protocol to which this row applies.

OBJECT-TYPE

The value of tmnxSysMgmtProtLastChange indicates the sysUpTime at the time of the last modification of this row. If no changes were made to the row since the last re-initialization of the local network management subsystem, then this object contains the value zero.

OBJECT-TYPE

The value of tmnxSysMgmtAllowImmediateChange specifies whether the user is allowed to make direct changes to the configuration, or whether all changes need to be applied through use of a candidate config.

OBJECT-TYPE

The value of tmnxSysMgmtCliEngine1 specifies the CLI engine that is active when a user logs in. Value systemDerived specifies that the CLI engine is derived from the current value of tmnxSysMgmtIfWriteMode: tmnxSysMgmtIfWriteMode -> CLI engine ---------------------- --------------------- classic -> Classic CLI modelDriven -> MD CLI mixed -> MD CLI Both tmnxSysMgmtCliEngine1 and tmnxSysMgmtCliEngine2 must be present in the same set request.

OBJECT-TYPE

The value of tmnxSysMgmtCliEngine2 specifies the secondary CLI engine that is accessible to a logged-in user. Value systemDerived specifies that the user does not have access to secondary engine (i.e.: can only access engine specified by tmnxSysMgmtCliEngine1). Values other than systemDerived are used only if tmnxSysMgmtCliEngine1 also has value other than systemDerived and must differ from that value. Both tmnxSysMgmtCliEngine1 and tmnxSysMgmtCliEngine2 must be present in the same set request.

OBJECT-IDENTITY

OBJECT-TYPE

The value of tmnxSysFileTransProfTableLstChgd indicates the time, since system startup, when tmnxSysFileTransProfTable last changed configuration. A value of zero indicates that no changes were made to this table since the system was last initialized.

OBJECT-TYPE

The tmnxSysFileTransProfTable contains objects used to configure instances of the file transmission profile, which are used by a device to download files from a server (e.g. File Transfer Protocol (FTP) server or Hypertext Transfer Protocol(HTTP) server). A file transmission profile specifies 1) the local configuration for sending and receiving a file in an Nokia SROS device; and 2) the behaviours of the device when the transmission fails. Usage example: Auto Certificate Revocation List (CRL) retrieval: downloading CRL from a FTP or an HTTP server to an Nokia SROS device. Entries in this table are created and deleted via SNMP set operations to tmnxSysFileTransProfRowStatus.

OBJECT-TYPE

Each tmnxSysFileTransProfEntry contains the configuration for one file transmission profile.

OBJECT-TYPE

The value of tmnxSysFileTransProfName uniquely specifies one file transmission profile configured on this system.

OBJECT-TYPE

The value of tmnxSysFileTransProfRowStatus specifies the status of this row. It is used to create and delete row entries in tmnxSysFileTransProfTable.

OBJECT-TYPE

The value of tmnxSysFileTransProfLastChanged indicates the time, since system startup, that the configuration of this row was created or modified.

OBJECT-TYPE

The value of tmnxSysFileTransProfRtrId specifies the virtual router instance. The file transmission connection(s) will be established between the virtual router and a server (e.g. FTP or HTTP server). Exactly one of tmnxSysFileTransProfSvcName, tmnxSysFileTransProfSvcId and tmnxSysFileTransProfRtrId must be configured to a non-default value. For example, when the value of tmnxSysFileTransProfRtrId is zero, the virtual router must be specified using tmnxSysFileTransProfSvcId or tmnxSysFileTransProfSvcName. Only those IDs corresponding to the 'Base' and 'management' virtual routers may be set in this object. Refer to TIMETRA-VRTR-MIB.mib::vRtrName.

OBJECT-TYPE

The value of tmnxSysFileTransProfSvcId specifies the service identifier for a virtual router. The file transmission connection(s) will be established between the virtual router and a server (e.g. FTP or HTTP server). Exactly one of tmnxSysFileTransProfSvcName, tmnxSysFileTransProfSvcId and tmnxSysFileTransProfRtrId must be configured to a non-default value. For example, when the value of tmnxSysFileTransProfSvcId is zero, the virtual router must be specified using tmnxSysFileTransProfSvcName or tmnxSysFileTransProfRtrId. Only VPRN service IDs are allowed.

OBJECT-TYPE

The value of tmnxSysFileTransProfSrcAddrV4T specifies the IP address type of tmnxSysFileTransProfSrcAddrV4. The value of tmnxSysFileTransProfSrcAddrV4T can be either of 'ipv4(1)' or 'unknown (0)'. The value of 'unknown(0)' specifies no IPv4 source address is configured.

OBJECT-TYPE

The value of tmnxSysFileTransProfSrcAddrV4 specifies the IPv4 source address specified in tmnxSysFileTransProfRtrId. The value of an empty string specifies no IPv4 source address is configured.

OBJECT-TYPE

The value of tmnxSysFileTransProfSrcAddrV6T specifies the IP address type of tmnxSysFileTransProfSrcAddrV6. The value of tmnxSysFileTransProfSrcAddrV6T can be either of 'ipv6(2)' or 'unknown (0)'. The value of 'unknown(0)' specifies no IPv6 source address is configured.

OBJECT-TYPE

The value of tmnxSysFileTransProfSrcAddrV6 specifies the IPv6 source address specified in tmnxSysFileTransProfRtrId. The value of an empty string specifies no IPv6 source address is configured.

OBJECT-TYPE

The value of tmnxSysFileTransProfTimeout specifies the connection timeout (in seconds) for the file transmission. The timeout is the maximum waiting time to receive any data from the server (e.g. FTP or HTTP server).

OBJECT-TYPE

The value of tmnxSysFileTransProfRetry specifies the number of retries of the file transmission profile. When the virtual router does not receive any data from a server (e.g. FTP or HTTP server) after the configured tmnxSysFileTransProfTimeout interval, the router may repeat the request to the server. The number of retries specifies the maximum number of repeated requests. Virtual router instances are configured using tmnxSysFileTransProfRtrId. The value of zero specifies that the request should not be resent by the virtual router after the configured tmnxSysFileTransProfTimeout interval elapsed.

OBJECT-TYPE

The value of tmnxSysFileTransProfRedirection specifies the maximum level of redirection of the file transmission profile. The virtual router may send a new request to another server if the requested resources are not available (e.g. temporarily available to another server). Usage example: When a virtual router receives an HTTP response with status code of redirection 3xx (e.g. 301 Moved Permanently), the router may send a new request to another location. The level of redirection specifies the maximum number of new requests that can be sent by a virtual router. For any file transmission protocols (e.g. FTP), which do not support redirection, the value of tmnxSysFileTransProfRedirection will be ignored. The value of zero specifies that no new request should be sent by a virtual router to another server.

OBJECT-TYPE

The value of tmnxSysFileTransProfSvcName specifies the service name for a virtual router. The file transmission connection(s) will be established between the virtual router and a server (e.g. FTP or HTTP server). Exactly one of tmnxSysFileTransProfSvcName, tmnxSysFileTransProfSvcId and tmnxSysFileTransProfRtrId must be configured to a non-default value. For example, when the value of tmnxSysFileTransProfSvcName is an empty string, the virtual router must be specified using tmnxSysFileTransProfSvcId or tmnxSysFileTransProfRtrId. Only VPRN service names are allowed.

OBJECT-IDENTITY

OBJECT-TYPE

The tmnxSmLaunchExtTable is an extension of the DISMAN-SCRIPT-MIB::smLaunchTable.

OBJECT-TYPE

Each row entry represents contains additional attributes for the smLaunchEntry. Entries cannot be created and deleted via SNMP SET operations.

OBJECT-TYPE

The value of tmnxSmLaunchExtAuthType indicates the module that last started a script by writing to DISMAN-SCRIPT-MIB::smLaunchStart. If no script has yet been started the value 'none(0)' is returned.

OBJECT-TYPE

If true script run is able to overide explicit lock of MD database. Hence giving priority to EHS/Cron script runs.

OBJECT-TYPE

The tmnxSmRunExtTable is an extension of the DISMAN-SCRIPT-MIB::smRunTable.

OBJECT-TYPE

Each row entry represents contains additional attributes for the smRunEntry. Entries cannot be created and deleted via SNMP SET operations.

OBJECT-TYPE

The value of tmnxSmRunExtAuthType indicates the module that started this run of a script by writing to DISMAN-SCRIPT-MIB::smLaunchStart. If no script has yet been started the value 'none(0)' is returned.

OBJECT-TYPE

The value of tmnxSmRunExtUserName indicates the name of the user account used to check access to CLI commands while executing the script. If no script has yet been started the empty string is returned.

OBJECT-TYPE

The tmnxSmRunArgsTable contains information pertaining to the arguments passed to the exec script.

OBJECT-TYPE

The tmnxSmRunArgsEntry provides the argument information for a specified exec script.

OBJECT-TYPE

The value of tmnxSmRunEventArgIndex specifies the argument index number associated with a particular tmnxSmRunArgsEntry.

OBJECT-TYPE

The value of tmnxSmRunEventArgName indicates the name of an argument passed to the exec script.

OBJECT-TYPE

The value of tmnxSmRunEventArgValue indicates the ASCII printable contents of the specified argument passed to the exec script.

OBJECT-IDENTITY

OBJECT-TYPE

The value of tmnxSysSwReposTableLastChanged indicates the time, since system startup, when tmnxSysSoftwareRepositoryTable last changed configuration.

OBJECT-TYPE

The tmnxSysSoftwareRepositoryTable contains configuration information about the system software repositories for extension chassis.

OBJECT-TYPE

The tmnxSysSoftwareRepositoryEntry consists of the configurable objects for the system software repositories.

OBJECT-TYPE

The value of tmnxSysSwReposName specifies a unique name which identifies the system software repository.

OBJECT-TYPE

The value of tmnxSysSwReposRowStatus specifies the row status. It allows the creation and deletion of rows in tmnxSysSoftwareRepositoryTable.

OBJECT-TYPE

The value of tmnxSysSwReposLastChanged indicates the time, since system startup, that the configuration of the system software repository was created or modified.

OBJECT-TYPE

The value of tmnxSysSwReposDescription specifies the description of the system software repository. An empty string indicates this object has not been configured.

OBJECT-TYPE

The value of tmnxSysSwReposPrimaryLocation specifies the primary location of the directory that contains the runtime image files for the system software repository. An empty string indicates this object has not been configured.

OBJECT-TYPE

The value of tmnxSysSwReposSecondaryLocation specifies the secondary location of the directory that contains the runtime image files for the system software repository. An empty string indicates this object has not been configured.

OBJECT-TYPE

The value of tmnxSysSwReposTertiaryLocation specifies the tertiary location of the directory that contains the runtime image files for the system software repository. An empty string indicates this object has not been configured.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

The value of tmnxSysGrpcAdminState specifies the desired administrative state of the gRPC server.

OBJECT-TYPE

The value of tmnxSysGrpcOperState indicates the current operational state of gRPC server.

OBJECT-TYPE

The value of tmnxSysGrpcTlsServerProfile specifies the name of the TLS server profile to be used.

OBJECT-TYPE

The value of tmnxSysGrpcMaxMsgSize specifies the maximum size of the received decompressed serialized protobuf message without metadata.

OBJECT-TYPE

The value of tmnxSysGrpcAutoCfgSave specifies whether the running configuration is saved as part of a commit operation initiated from gRPC.

OBJECT-TYPE

The value of tmnxSysGrpcGnmiVersion indicates the version of gNMI service provided by gRPC server.

OBJECT-TYPE

The value of tmnxSysGrpcAllowUnsecure specifies whether gRPC server will run without secured transport protocol. Username and password will be transferred in unencrypted form with each RPC request.

OBJECT-TYPE

The value of tmnxSysGrpcGnmiAdminState specifies the desired administrative state of the gNMI service.

OBJECT-TYPE

The value of tmnxSysGrpcTcpKaAdminState specifies the administrative state of the TCP keepalive algorithm.

OBJECT-TYPE

The value of the object tmnxSysGrpcTcpKaIdle specifies the number of seconds until the first TCP keepalive probe is sent.

OBJECT-TYPE

The value of the object tmnxSysGrpcTcpKaInterval specifies the number of seconds between two TCP keepalives probes.

OBJECT-TYPE

The value of the object tmnxSysGrpcTcpKaCount specifies the number of missed keepalives before the TCP connection is declared down.

OBJECT-TYPE

The value of tmnxSysGrpcRibApiAdminState specifies the desired administrative state of the 'RibApi' service.

OBJECT-TYPE

The value of the object tmnxSysGrpcRibApiPurgeTimeout specifies the number of seconds until stale entries are purged. The value of zero specifies that the purge will happen immediately after controller disconnection is detected.

OBJECT-TYPE

The value of tmnxSysGrpcRibApiVersion indicates the version of RibApi service provided by gRPC server.

OBJECT-TYPE

The value of tmnxSysGrpcGnoiCertMgmtAdmnState specifies the desired administrative state of the 'gNOI CertificateManagement' service.

OBJECT-TYPE

The value of tmnxSysGrpcGnoiCertMgmtVersion indicates the version of 'gNOI CertificateManagement' service provided by gRPC server.

OBJECT-IDENTITY

OBJECT-TYPE

The value of tmnxSysMgmtIfMDCliAutoCfgSave specifies whether the running configuration is saved as part of a commit operation initiated from MD CLI.

OBJECT-TYPE

The value of tmnxSysMgmtIfMDEnvComplEnter specifies whether the command completion on enter character is allowed in MD CLI.

OBJECT-TYPE

The value of tmnxSysMgmtIfMDEnvComplSpace specifies whether the command completion on space character is allowed in MD CLI.

OBJECT-TYPE

The value of tmnxSysMgmtIfMDEnvComplTab specifies whether the command completion on tab character is allowed in MD CLI.

OBJECT-TYPE

The value of tmnxSysMgmtIfMDEnvConsLength specifies number of lines displayed on the console screen in MD CLI.

OBJECT-TYPE

The value of tmnxSysMgmtIfMDEnvConsWidth specifies number of columns displayed on the console screen in MD CLI.

OBJECT-TYPE

The value of tmnxSysMgmtIfMDEnvMore specifies whether paging of the output text in MD CLI is enabled. This applies to continuous text output from a single command that is capable of filling the entire screen.

OBJECT-TYPE

The value of tmnxSysMgmtIfMDEnvPromptCtx controls displaying of the current command context in MD CLI prompt.

OBJECT-TYPE

The value of tmnxSysMgmtIfMDEnvPromptNewline controls displaying of a newline before every prompt line in MD CLI.

OBJECT-TYPE

The value of tmnxSysMgmtIfMDEnvPromptTime controls displaying of a timestamp before the first prompt line in MD CLI.

OBJECT-TYPE

The value of tmnxSysMgmtIfMDEnvPromptIndic controls displaying of the indicator of uncommitted changes in MD CLI prompt. The value set to true indicates that asterisk (*) is displayed in case of uncommitted changes are present in global configuration candidate datastore. The value set to false means that no indicator is displayed.

OBJECT-TYPE

The value of tmnxSysMgmtIfMDEnvTimeDisplay specifies the time zone to be used, when displaying timestamp before prompt in MD CLI.

OBJECT-TYPE

The value of tmnxSysMgmtIfMDEnvMsgCliSvrt specifies severity threshold for MD-CLI messages.

OBJECT-TYPE

The value of tmnxSysMgmtIfMDEnvProIndAdminSt specifies whether progress indicator is active in MD-CLI.

OBJECT-TYPE

Type of the progress indicator used in the MD-CLI.

OBJECT-TYPE

Delay before progress indicator is displayed in MD-CLI.

OBJECT-TYPE

The value of tmnxSysMgmtIfMDCliCmdAccntLoad specifies whether remote command accounting is performed during an MD-CLI load or rollback operation.

OBJECT-TYPE

The value of tmnxSysMgmtIfMDEnvTimeFormat specifies the time format to be used, when displaying timestamp in info command in MD CLI.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

The value of tmnxSysMgmtIfYangBaseR13 specifies whether or not the base release 13 YANG models are supported. When set to 'true', network managers can access base release 13 YANG models.

OBJECT-TYPE

The value of tmnxSysMgmtIfYangNokia specifies whether or not the Nokia YANG models are supported. When set to 'true', network managers can access Nokia YANG models.

OBJECT-TYPE

The value of tmnxSysMgmtIfYangOpenConfig specifies whether or not the OpenConfig YANG models are supported. When set to 'true', network managers can access OpenConfig YANG models.

OBJECT-TYPE

The value of tmnxSysMgmtIfYangNokiaCombined specifies whether or not the combined Nokia YANG models are supported. When set to 'true', network managers can access combined Nokia YANG models. tmnxSysMgmtIfYangNokiaCombined and tmnxSysMgmtIfYangNokia are mutually exclusive and cannot be both set to true at the same time.

OBJECT-IDENTITY

OBJECT-TYPE

The value of tmnxSysMgmtIfWriteMode specifies the router configuration mode's requested provisional state. classic (1) - configuration is managed by classic interfaces only (e.g. classic CLI and SNMP). modelDriven (2) - configuration is managed by model-driven interfaces only (e.g. MD-CLI, Netconf, and gNMI). mixed (3) - configuration is managed (with restrictions) with both classic and model-driven interfaces. When the value of tmnxSysMgmtIfWriteOperMode is in 'modelDriven (2)' mode, SNMP Set-PDUs are rejected (ResourceUnavailable(13))). To re-enable SNMP access an operator MUST have write-access to CLI or a newer interface such as Netconf or gNMI and set the mode to either 'classic (1)' or 'mixed (3)'.

OBJECT-TYPE

The value of tmnxSysMgmtIfWriteOperMode indicates the router configuration mode operationalized by the system. syncing (0) - The system is in transition between modes. Write access is restricted in all interfaces. classic (1) - configuration is managed by classic interfaces only (e.g. classic CLI and SNMP). modelDriven (2) - configuration is managed by modelDriven interfaces only (e.g. MD-CLI, Netconf, and gNMI). mixed (3) - configuration is managed (with restrictions) with both classic and modelDriven interfaces.

OBJECT-TYPE

The value of tmnxSysMgmtIfModeLastSwitchTime indicates the time when a configuration-mode switch was last performed.

OBJECT-TYPE

The value of tmnxSysMgmtIfModeSwitchDuration indicates the time, in milliseconds, that the last configuration-mode switch took to become active.

OBJECT-TYPE

The table tmnxSysMgmtIfDstoreLocksTable contains read-only information pertaining to configuration datastores' locks.

OBJECT-TYPE

Each row represents a single user session. Rows in the table tmnxSysMgmtIfDstoreLocksEntry are automatically created by the system when user acquires database connection and destroyed when client closes the connection.

OBJECT-TYPE

The value of the object tmnxSysMgmtIfDsLocksSessionId indicates the session ID of user session with open database connection, which can block other users from locking specific datastore.

OBJECT-TYPE

The value of the object tmnxSysMgmtIfDsLocksRmtIpAddress indicates the remote IP address of the user session. Empty address in case of console connection and tmnxSysMgmtIfDsLocksConsole is set to true.

OBJECT-TYPE

The value of tmnxSysMgmtIfDsLocksConsole indicates session session origin. Value true(1) represents for console connection and false(2) is used for Cron/EHS or rest of connections identified by IP address in tmnxSysMgmtIfDsLocksRmtIpAddress.

OBJECT-TYPE

The value of the object tmnxSysMgmtIfDsLocksUserName indicates the name of the user who initiated the session.

OBJECT-TYPE

The value of tmnxSysMgmtIfDsLocksSessionMode indicates the candidate datastore access session mode: global (1) - write access to the global candidate datastore can be granted to multiple sessions exclusive (2) - write access to the global candidate datastore and the running datastore is limited to a single session private (3) - write access to a candidate datastore can be granted to multiple sessions, each with their own private candidate datastore privateExclusive (4) - write access to the private candidate datastore is granted, in addition, a single session is granted write access to the running datastore. readOnly (5) - access to the datastore without write permissions.

OBJECT-TYPE

The value of tmnxSysMgmtIfDsLocksSessionType indicates the type of management interface, which was used to obtain the lock.

OBJECT-TYPE

The value of the object tmnxSysMgmtIfDsLocksRegion indicates the name of the configuration region.

OBJECT-TYPE

The value of tmnxSysMgmtIfDsLocksRunLock indicates running datastore lock state

OBJECT-TYPE

The value of tmnxSysMgmtIfDsLocksCndLock indicates candidate datastore lock state

OBJECT-TYPE

The value of tmnxSysMgmtIfDsLocksIdleTime indicates the idle time of user. For the CLI sessions the idle time is the period of time after last key pressed. For the NETCONF it is the period of time after session creation. For the GMI we do not track idle time.

OBJECT-TYPE

The value of tmnxSysMgmtIfDsLocksScratchCnt indicates the number of scratchpads in use for session

OBJECT-TYPE

The value of tmnxSysMgmtIfDsLocksCronEhs indicates whether the session is a Cron/EHS session Value true(1) represents Cron/EHS session and false(2) is used for console or rest of connections identified by IP address in tmnxSysMgmtIfDsLocksRmtIpAddress.

OBJECT-TYPE

The value of tmnxSysMgmtIfSchemaPath specifies the path to schema files used by the system. The value of this object defaults to 'cf3:/YANG'.

OBJECT-TYPE

The value of tmnxSysMgmtIfWriteSwitchReason indicates the origin cause of the router configuration mode switch. boot(0) - The system booted in the current mode. manual (1) - An operator manually switched to the current mode. validation (2) - Validation failure was detected, causing the mode switch.

OBJECT-TYPE

The table tmnxSysGrpcConnTable contains read-only information pertaining to gRPC server connections.

OBJECT-TYPE

Each row entry represents a single TCP connection towards gRPC server. Rows in the table tmnxSysGrpcConnEntry are automatically created by the system when client connect to gRPC server and destroyed when client disconnect.

OBJECT-TYPE

The value of the object tmnxSysGrpcConnSrcIpAddType indicates the type of IP address stored in tmnxSysGrpcConnSrcIpAddress. The value can be either 'unknown', 'ipv4' or 'ipv6.

OBJECT-TYPE

The value of the object tmnxSysGrpcConnSrcIpAddress indicates the remote IP address of the gRPC client.

OBJECT-TYPE

The value of the object tmnxSysGrpcConnSrcPort indicates the remote port of the gRPC client.

OBJECT-TYPE

The value of tmnxSysGrpcConnStartTime indicates the time when connection towards gRPC server was established.

OBJECT-TYPE

The value of tmnxSysGrpcConnActRpcCnt indicates the active number of RPC on this connection.

OBJECT-TYPE

The value of tmnxSysGrpcConnTotRpcCnt indicates the total number of RPC on this connection since establishment time.

OBJECT-TYPE

The value of tmnxSysGrpcConnRxBytes indicates the total number of bytes received over this connection.

OBJECT-TYPE

The value of tmnxSysGrpcConnTxBytes indicates the total number of bytes sent over this connection.

OBJECT-TYPE

The value of tmnxSysGrpcConnQos indicates the DSCP value of the connection. Only first Subscribe RPC with qos request is accepted on connection. DSCP value is reset to sgt-qos default after last Subscribe RPC on connection is terminated.

OBJECT-TYPE

The value of the object tmnxSysGrpcConnSrcVRtrId indicates the virtual router instance ID of the gRPC client.

OBJECT-IDENTITY

OBJECT-TYPE

The value of tmnxSysHttpRdrCpmOptimizedMode specifies if the CPM uses the optimized mode for HTTP redirect messages.

OBJECT-TYPE

The table tmnxSysGrpcRpcTable contains read-only information pertaining to gRPC server RPCs.

OBJECT-TYPE

Each row entry represents a single RPC towards gRPC server. Rows in the table tmnxSysGrpcRpcEntry are automatically created by the system when client send RPC towards gRPC server and destroyed when RPC execution is finished or cancelled.

OBJECT-TYPE

The value of the object tmnxSysGrpcRpcId indicates the system generated unique RPC ID.

OBJECT-TYPE

The value of the object tmnxSysGrpcRpcName indicates the name of a RPC.

OBJECT-TYPE

The value of the object tmnxSysGrpcRpcServiceName indicates the name of a RPC service.

OBJECT-TYPE

The value of tmnxSysGrpcRpcStartTime indicates the time of a RPC arrival to gRPC server.

OBJECT-TYPE

The value of the object tmnxSysGrpcRpcSrcIpAddType indicates the type of IP address stored in tmnxSysGrpcRpcSrcIpAddress. The value can be either 'unknown', 'ipv4' or 'ipv6.

OBJECT-TYPE

The value of the object tmnxSysGrpcRpcSrcIpAddress indicates the remote IP address of gRPC client who sent a RPC.

OBJECT-TYPE

The value of the object tmnxSysGrpcRpcSrcPort indicates the remote port of gRPC client who sent a RPC.

OBJECT-TYPE

The value of the object tmnxSysGrpcRpcUserName indicates the name of a system user who initiated a RPC. The value might be empty if client did not provide username or if a RPC was not yet authenticated.

OBJECT-TYPE

The value of the object tmnxSysGrpcRpcSessionId indicates the session-id of a system user who initiated a RPC. The value might be zero if a RPC was not yet authenticated.

OBJECT-IDENTITY

OBJECT-TYPE

The value of tmnxSysNEProfTableLstChgd indicates the time, since system startup, when tmnxSysNEProfTable last changed configuration. A value of zero indicates that no changes were made to this table since the system was last initialized.

OBJECT-TYPE

The tmnxSysNEProfTable contains objects used to configure instances of the network element profile, which are used for node discovery. Entries in this table are created and deleted via SNMP set operations to tmnxSysNEProfRowStatus.

OBJECT-TYPE

Each tmnxSysNEProfEntry contains the configuration for one network element profile.

OBJECT-TYPE

The value of tmnxSysNEProfName uniquely specifies one network element profile configured on this system.

OBJECT-TYPE

The value of tmnxSysNEProfRowStatus specifies the status of this row. It is used to create and delete row entries in tmnxSysNEProfTable.

OBJECT-TYPE

The value of tmnxSysNEProfLastChanged indicates the time, since system startup, that the configuration of this row was created or modified.

OBJECT-TYPE

The value of tmnxSysNEProfNeid specifies the Network Element Identifier. The first 8 high-order bits indicate the subnet ID and and range from 0x1 to 0xFE. The 16 low-order bits indicate the basic ID and ranges from 0x0001 to 0xFFFE.

OBJECT-TYPE

The value of tmnxSysNEProfNeipV4Type specifies the IP address type of tmnxSysNEProfNeipV4. The value of tmnxSysNEProfNeipV4Type can be either of 'ipv4(1)' or 'unknown (0)'. The value of 'unknown(0)' specifies no NEIP v4 address is configured.

OBJECT-TYPE

The value of tmnxSysNEProfNeipV4 indicates the IPv4 address of the Network Element.

OBJECT-TYPE

The value of tmnxSysNEProfNeipV6Type specifies the IP address type of tmnxSysNEProfNeipV6. The value of tmnxSysNEProfNeipV6Type can be either of 'ipv6(2)' or 'unknown (0)'. The value of 'unknown(0)' specifies no NEIP v6 address is configured.

OBJECT-TYPE

The value of tmnxSysNEProfNeipV6 indicates the IPv6 address of the Network Element.

OBJECT-TYPE

The value of tmnxSysNEProfSystemMac specifies the system MAC address of the node. A value of all zeroes indicates this object is not configured, the chassis MAC address will be used.

OBJECT-TYPE

The value of tmnxSysNEProfPlatformType specifies the product identifier. An empty string indicates this object is not configured, the chassis name and chassis type will be used.

OBJECT-TYPE

The value of tmnxSysNEProfVendorId specifies the vendor identifier.

OBJECT-TYPE

The value of tmnxSysNEDiscoveryGenerateTraps specifies whether to generate Network Element Discovery notifications or not.

OBJECT-IDENTITY

OBJECT-TYPE

The value of tmnxSysFpoDscpTransAdminState specifies the administrative state of the DSCP transparency forwarding path option.

OBJECT-TYPE

The value of tmnxSysFpoDscpTransOperState indicates the operational state of the DSCP transparency forwarding path option.

OBJECT-TYPE

The value of tmnxSysFpoEntropyLabelAdminState specifies the administrative state of the entropy label forwarding path option.

OBJECT-TYPE

The value of tmnxSysFpoEntropyLabelOperState indicates the operational state of the entropy label forwarding path option.

OBJECT-TYPE

The value of tmnxSysFpoMacFltOutVlanPrioAdmSt specifies the administrative state of the MAC filter outer VLAN priority forwarding path option.

OBJECT-TYPE

The value of tmnxSysFpoMacFltOutVlanPrioOprSt indicates the operational state of the MAC filter outer VLAN priority forwarding path option.

OBJECT-TYPE

The value of tmnxSysFpoVplsEvpnMplsAdminState specifies the administrative state of the VPLS EVPN MPLS forwarding path option.

OBJECT-TYPE

The value of tmnxSysFpoVplsEvpnMplsOperState indicates the operational state of the VPLS EVPN MPLS forwarding path option.

OBJECT-TYPE

The value of tmnxSysFpoQosFc4ProfAdminState specifies the administrative state of the four color mode forwarding path option.

OBJECT-TYPE

The value of tmnxSysFpoQosFc4ProfOperState indicates the operational state of the four color mode forwarding path option.

OBJECT-TYPE

The value of tmnxSysFpoQosMacCritAdminState specifies the administrative state of the MAC criteria for forwarding path option.

OBJECT-TYPE

The value of tmnxSysFpoQosMacCritOperState indicates the operational state of the MAC criteria for forwarding path option.

OBJECT-TYPE

The value of tmnxSysFpoQosIpv6CritAdminState specifies the administrative state of the IPv6 criteria for forwarding path option.

OBJECT-TYPE

The value of tmnxSysFpoQosIpv6CritOperState indicates the operational state of the IPv6 criteria for forwarding path option.

OBJECT-TYPE

The value of tmnxSysFpoQosBumPolAdminState specifies the administrative state of the BUM policers for forwarding path option.

OBJECT-TYPE

The value of tmnxSysFpoQosBumPolOperState indicates the operational state of the BUM policers for forwarding path option.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY