OSPFV3-MIB
- Registered at
- 1.3.6.1.2.1.191
- Last updated
- 2009-08-13 00:00
- Organization
- IETF OSPF Working Group
- Revisions
- 2009-08-13 00:00
- Namespace
- standard
- Source file
OSPFV3-MIB- Digest
sha256:d4d428c109ebac0baae736c4d1c3787a02b20fbf5162d8b085d4bbfbd840298f
Description
The MIB module for OSPF version 3. Copyright (c) 2009 IETF Trust and the persons identified as authors of the code. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: - Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. - Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. - Neither the name of Internet Society, IETF or IETF Trust, nor the names of specific contributors, may be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS 'AS IS' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. This version of this MIB module is part of RFC 5643; see the RFC itself for full legal notices.
Contact
WG E-Mail: ospf@ietf.org WG Chairs: Acee Lindem acee@redback.com Abhay Roy akr@cisco.com Editors: Dan Joyal Nortel 600 Technology Park Drive Billerica, MA 01821, USA djoyal@nortel.com Vishwas Manral IP Infusion Almora, Uttarakhand India vishwas@ipinfusion.com
Imports
| From | Symbols |
|---|---|
| IF-MIB | InterfaceIndex |
| INET-ADDRESS-MIB | InetAddress, InetAddressIPv6, InetAddressPrefixLength, InetAddressType |
| OSPF-MIB | BigMetric, DesignatedRouterPriority, HelloRange, Metric, Status |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP |
| SNMPv2-SMI | Counter32, Gauge32, Integer32, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, Unsigned32, iso, mib-2 |
| SNMPv2-TC | DisplayString, RowStatus, TEXTUAL-CONVENTION, TimeStamp, TruthValue |
Imported by
2 module(s) in this corpus import this one.
Load order
Every file a consumer needs in order to load this module, dependencies first.
IANAifType-MIB IF-MIB INET-ADDRESS-MIB OSPF-MIB OSPFV3-MIB SNMPv2-CONF SNMPv2-MIB SNMPv2-SMI SNMPv2-TC
Textual conventions
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| Ospfv3AreaIdTC TEXTUAL-CONVENTION An OSPFv3 Area Identifier. A value of zero identifies the backbone area. | current | |||
| Ospfv3DeadIntervalRangeTC TEXTUAL-CONVENTION The range, in seconds, of dead interval value. | current | |||
| Ospfv3IfInstIdTC TEXTUAL-CONVENTION An OSPFv3 Interface Instance ID. | current | |||
| Ospfv3LsIdTC TEXTUAL-CONVENTION A unique 32-bit identifier of the piece of the routing domain that is being described by a link state advertisement. In contrast to OSPFv2, the Link State ID (LSID) has no addressing semantics. | current | |||
| Ospfv3LsaAgeTC TEXTUAL-CONVENTION The age of the link state advertisement in seconds. The high-order bit of the LS age field is considered the DoNotAge bit for support of on-demand circuits. | current | |||
| Ospfv3LsaSequenceTC TEXTUAL-CONVENTION The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number, the more recent the advertisement. | current | |||
| Ospfv3RouterIdTC TEXTUAL-CONVENTION A 32-bit, unsigned integer uniquely identifying the router in the Autonomous System. To ensure uniqueness, this may default to the value of one of the router's IPv4 host addresses if IPv4 is configured on the router. | current | |||
| Ospfv3UpToRefreshIntervalTC TEXTUAL-CONVENTION The values one might be able to configure for variables bounded by the Refresh Interval. | current |
Objects
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| ospfv3Notifications OBJECT-IDENTITY | 1.3.6.1.2.1.191.0 | |||
| ospfv3Objects OBJECT-IDENTITY | 1.3.6.1.2.1.191.1 | |||
| ospfv3GeneralGroup OBJECT-IDENTITY | 1.3.6.1.2.1.191.1.1 | |||
| ospfv3RouterId OBJECT-TYPE A 32-bit unsigned integer uniquely identifying the router in the Autonomous System. To ensure uniqueness, this may default to the 32-bit unsigned integer representation of one of the router's IPv4 interface addresses (if IPv4 is configured on the router). This object is persistent, and when written, the entity SHOULD save the change to non-volatile storage. | 1.3.6.1.2.1.191.1.1.1 | Ospfv3RouterIdTC | read-write | current |
| ospfv3AdminStatus OBJECT-TYPE The administrative status of OSPFv3 in the router. The value 'enabled' denotes that the OSPFv3 Process is active on at least one interface; 'disabled' disables it on all interfaces. This object is persistent, and when written, the entity SHOULD save the change to non-volatile storage. | 1.3.6.1.2.1.191.1.1.2 | Status | read-write | current |
| ospfv3VersionNumber OBJECT-TYPE The version number of OSPF for IPv6 is 3. | 1.3.6.1.2.1.191.1.1.3 | INTEGER {version3(3)} | read-only | current |
| ospfv3AreaBdrRtrStatus OBJECT-TYPE A flag to denote whether this router is an area border router. The value of this object is true (1) when the router is an area border router. | 1.3.6.1.2.1.191.1.1.4 | TruthValue | read-only | current |
| ospfv3ASBdrRtrStatus OBJECT-TYPE A flag to note whether this router is configured as an Autonomous System border router. This object is persistent, and when written, the entity SHOULD save the change to non-volatile storage. | 1.3.6.1.2.1.191.1.1.5 | TruthValue | read-write | current |
| ospfv3AsScopeLsaCount OBJECT-TYPE The number of AS-scope (e.g., AS-External) link state advertisements in the link state database. | 1.3.6.1.2.1.191.1.1.6 | Gauge32 | read-only | current |
| ospfv3AsScopeLsaCksumSum OBJECT-TYPE The 32-bit unsigned sum of the LS checksums of the AS-scoped link state advertisements contained in the link state database. This sum can be used to determine if there has been a change in a router's link state database or to compare the link state database of two routers. | 1.3.6.1.2.1.191.1.1.7 | Unsigned32 | read-only | current |
| ospfv3OriginateNewLsas OBJECT-TYPE The number of new link state advertisements that have been originated. This number is incremented each time the router originates a new LSA. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times as indicated by the value of ospfv3DiscontinuityTime. | 1.3.6.1.2.1.191.1.1.8 | Counter32 | read-only | current |
| ospfv3RxNewLsas OBJECT-TYPE The number of link state advertisements received that are determined to be new instantiations. This number does not include newer instantiations of self-originated link state advertisements. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times as indicated by the value of ospfv3DiscontinuityTime. | 1.3.6.1.2.1.191.1.1.9 | Counter32 | read-only | current |
| ospfv3ExtLsaCount OBJECT-TYPE The number of External (LS type 0x4005) in the link state database. | 1.3.6.1.2.1.191.1.1.10 | Gauge32 | read-only | current |
| ospfv3ExtAreaLsdbLimit OBJECT-TYPE The maximum number of non-default AS-external-LSA entries that can be stored in the link state database. If the value is -1, then there is no limit. When the number of non-default AS-external-LSAs in a router's link state database reaches ospfv3ExtAreaLsdbLimit, the router enters Overflow state. The router never holds more than ospfv3ExtAreaLsdbLimit non-default AS-external-LSAs in its database. ospfv3ExtAreaLsdbLimit MUST be set identically in all routers attached to the OSPFv3 backbone and/or any regular OSPFv3 area (i.e., OSPFv3 stub areas and not-so-stubby-areas (NSSAs) are excluded). This object is persistent, and when written, the entity SHOULD save the change to non-volatile storage. | 1.3.6.1.2.1.191.1.1.11 | Integer32 (-1..2147483647) | read-write | current |
| ospfv3ExitOverflowInterval OBJECT-TYPE The number of seconds that, after entering Overflow state, a router will attempt to leave Overflow state. This allows the router to again originate non-default, AS-External-LSAs. When set to 0, the router will not leave Overflow state until restarted. This object is persistent, and when written, the entity SHOULD save the change to non-volatile storage. | 1.3.6.1.2.1.191.1.1.12 | Unsigned32 | read-write | current |
| ospfv3DemandExtensions OBJECT-TYPE The router's support for demand circuits. The value of this object is true (1) when demand circuits are supported. This object is persistent, and when written, the entity SHOULD save the change to non-volatile storage. | 1.3.6.1.2.1.191.1.1.13 | TruthValue | read-write | current |
| ospfv3ReferenceBandwidth OBJECT-TYPE Reference bandwidth in kilobits per second for calculating default interface metrics. The default value is 100,000 KBPS (100 MBPS). This object is persistent, and when written, the entity SHOULD save the change to non-volatile storage. | 1.3.6.1.2.1.191.1.1.14 | Unsigned32 | read-write | current |
| ospfv3RestartSupport OBJECT-TYPE The router's support for OSPF graceful restart. Options include no restart support, only planned restarts, or both planned and unplanned restarts. This object is persistent, and when written, the entity SHOULD save the change to non-volatile storage. | 1.3.6.1.2.1.191.1.1.15 | INTEGER {none(1), plannedOnly(2), plannedAndUnplanned(3)} | read-write | current |
| ospfv3RestartInterval OBJECT-TYPE Configured OSPF graceful restart timeout interval. This object is persistent, and when written, the entity SHOULD save the change to non-volatile storage. | 1.3.6.1.2.1.191.1.1.16 | Ospfv3UpToRefreshIntervalTC | read-write | current |
| ospfv3RestartStrictLsaChecking OBJECT-TYPE Indicates if strict LSA checking is enabled for graceful restart. A value of true (1) indicates that strict LSA checking is enabled. This object is persistent, and when written, the entity SHOULD save the change to non-volatile storage. | 1.3.6.1.2.1.191.1.1.17 | TruthValue | read-write | current |
| ospfv3RestartStatus OBJECT-TYPE The current status of OSPF graceful restart capability. | 1.3.6.1.2.1.191.1.1.18 | INTEGER {notRestarting(1), plannedRestart(2), unplannedRestart(3)} | read-only | current |
| ospfv3RestartAge OBJECT-TYPE Remaining time in the current OSPF graceful restart interval. | 1.3.6.1.2.1.191.1.1.19 | Ospfv3UpToRefreshIntervalTC | read-only | current |
| ospfv3RestartExitReason OBJECT-TYPE Describes the outcome of the last attempt at a graceful restart. none: no restart has yet been attempted. inProgress: a restart attempt is currently underway. completed: the last restart completed successfully. timedOut: the last restart timed out. topologyChanged: the last restart was aborted due to a topology change. | 1.3.6.1.2.1.191.1.1.20 | INTEGER {none(1), inProgress(2), completed(3), timedOut(4), topologyChanged(5)} | read-only | current |
| ospfv3NotificationEnable OBJECT-TYPE This object provides a coarse level of control over the generation of OSPFv3 notifications. If this object is set to true (1), then it enables the generation of OSPFv3 notifications. If it is set to false (2), these notifications are not generated. This object is persistent, and when written, the entity SHOULD save the change to non-volatile storage. | 1.3.6.1.2.1.191.1.1.21 | TruthValue | read-write | current |
| ospfv3StubRouterSupport OBJECT-TYPE The router's support for stub router functionality. An object value of true (1) indicates that stub router functionality is supported. | 1.3.6.1.2.1.191.1.1.22 | TruthValue | read-only | current |
| ospfv3StubRouterAdvertisement OBJECT-TYPE This object controls the advertisement of stub LSAs by the router. The value doNotAdvertise (1) will result in the advertisement of standard LSAs and is the default value. This object is persistent, and when written, the entity SHOULD save the change to non-volatile storage. | 1.3.6.1.2.1.191.1.1.23 | INTEGER {doNotAdvertise(1), advertise(2)} | read-write | current |
| ospfv3DiscontinuityTime OBJECT-TYPE The value of sysUpTime on the most recent occasion at which any one of this MIB's counters suffered a discontinuity. If no such discontinuities have occurred since the last re-initialization of the local management subsystem, then this object contains a zero value. | 1.3.6.1.2.1.191.1.1.24 | TimeStamp | read-only | current |
| ospfv3RestartTime OBJECT-TYPE The value of sysUpTime on the most recent occasion at which the ospfv3RestartExitReason was updated. | 1.3.6.1.2.1.191.1.1.25 | TimeStamp | read-only | current |
| ospfv3AreaTable OBJECT-TYPE Information describing the configured parameters and cumulative statistics of the router's attached areas. The interfaces and virtual links are configured as part of these areas. Area 0, by definition, is the backbone area. | 1.3.6.1.2.1.191.1.2 | not-accessible | current | |
| ospfv3AreaEntry OBJECT-TYPE Information describing the configured parameters and cumulative statistics of one of the router's attached areas. The information in this table is persistent, and when written, the entity SHOULD save the a change to non-volatile storage. | 1.3.6.1.2.1.191.1.2.1 | not-accessible | current | |
| ospfv3AreaId OBJECT-TYPE A 32-bit unsigned integer uniquely identifying an area. Area ID 0 is used for the OSPFv3 backbone. | 1.3.6.1.2.1.191.1.2.1.1 | Ospfv3AreaIdTC | not-accessible | current |
| ospfv3AreaImportAsExtern OBJECT-TYPE Indicates whether an area is a stub area, NSSA, or standard area. AS-scope LSAs are not imported into stub areas or NSSAs. NSSAs import AS-External data as NSSA LSAs that have Area-scope. | 1.3.6.1.2.1.191.1.2.1.2 | INTEGER {importExternal(1), importNoExternal(2), importNssa(3)} | read-create | current |
| ospfv3AreaSpfRuns OBJECT-TYPE The number of times that the intra-area route table has been calculated using this area's link state database. This is typically done using Dijkstra's algorithm. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times as indicated by the value of ospfv3DiscontinuityTime. | 1.3.6.1.2.1.191.1.2.1.3 | Counter32 | read-only | current |
| ospfv3AreaBdrRtrCount OBJECT-TYPE The total number of area border routers reachable within this area. This is initially zero, and is calculated in each Shortest Path First (SPF) pass. | 1.3.6.1.2.1.191.1.2.1.4 | Gauge32 | read-only | current |
| ospfv3AreaAsBdrRtrCount OBJECT-TYPE The total number of Autonomous System border routers reachable within this area. This is initially zero, and is calculated in each SPF pass. | 1.3.6.1.2.1.191.1.2.1.5 | Gauge32 | read-only | current |
| ospfv3AreaScopeLsaCount OBJECT-TYPE The total number of Area-scope link state advertisements in this area's link state database. | 1.3.6.1.2.1.191.1.2.1.6 | Gauge32 | read-only | current |
| ospfv3AreaScopeLsaCksumSum OBJECT-TYPE The 32-bit unsigned sum of the Area-scope link state advertisements' LS checksums contained in this area's link state database. The sum can be used to determine if there has been a change in a router's link state database or to compare the link state database of two routers. | 1.3.6.1.2.1.191.1.2.1.7 | Unsigned32 | read-only | current |
| ospfv3AreaSummary OBJECT-TYPE The variable ospfv3AreaSummary controls the import of Inter-Area LSAs into stub and NSSA areas. It has no effect on other areas. If it is noAreaSummary, the router will neither originate nor propagate Inter-Area LSAs into the stub or NSSA area. It will only advertise a default route. If it is sendAreaSummary, the router will both summarize and propagate Inter-Area LSAs. | 1.3.6.1.2.1.191.1.2.1.8 | INTEGER {noAreaSummary(1), sendAreaSummary(2)} | read-create | current |
| ospfv3AreaRowStatus OBJECT-TYPE This object permits management of the table by facilitating actions such as row creation, construction, and destruction. The value of this object has no effect on whether other objects in this conceptual row can be modified. | 1.3.6.1.2.1.191.1.2.1.9 | RowStatus | read-create | current |
| ospfv3AreaStubMetric OBJECT-TYPE The metric value advertised for the default route into stub and NSSA areas. By default, this equals the least metric among the interfaces to other areas. | 1.3.6.1.2.1.191.1.2.1.10 | BigMetric | read-create | current |
| ospfv3AreaNssaTranslatorRole OBJECT-TYPE Indicates an NSSA border router's policy to perform NSSA translation of NSSA-LSAs into AS-External-LSAs. | 1.3.6.1.2.1.191.1.2.1.11 | INTEGER {always(1), candidate(2)} | read-create | current |
| ospfv3AreaNssaTranslatorState OBJECT-TYPE Indicates if and how an NSSA border router is performing NSSA translation of NSSA-LSAs into AS-External-LSAs. When this object is set to 'enabled', the NSSA border router's ospfv3AreaNssaTranslatorRole has been set to 'always'. When this object is set to 'elected', a candidate NSSA border router is translating NSSA-LSAs into AS-External-LSAs. When this object is set to 'disabled', a candidate NSSA Border router is NOT translating NSSA-LSAs into AS-External-LSAs. | 1.3.6.1.2.1.191.1.2.1.12 | INTEGER {enabled(1), elected(2), disabled(3)} | read-only | current |
| ospfv3AreaNssaTranslatorStabInterval OBJECT-TYPE The stability interval defined as the number of seconds after an elected translator determines its services are no longer required that it should continue to perform its translation duties. | 1.3.6.1.2.1.191.1.2.1.13 | Unsigned32 | read-create | current |
| ospfv3AreaNssaTranslatorEvents OBJECT-TYPE Indicates the number of Translator state changes that have occurred since the last start-up of the OSPFv3 routing process. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times as indicated by the value of ospfv3DiscontinuityTime. | 1.3.6.1.2.1.191.1.2.1.14 | Counter32 | read-only | current |
| ospfv3AreaStubMetricType OBJECT-TYPE This variable assigns the type of metric advertised as a default route. | 1.3.6.1.2.1.191.1.2.1.15 | INTEGER {ospfv3Metric(1), comparableCost(2), nonComparable(3)} | read-create | current |
| ospfv3AreaTEEnabled OBJECT-TYPE Indicates whether or not traffic engineering is enabled in the area. The object is set to the value true (1) to enable traffic engineering. Traffic engineering is disabled by default. | 1.3.6.1.2.1.191.1.2.1.16 | TruthValue | read-create | current |
| ospfv3AsLsdbTable OBJECT-TYPE The OSPFv3 Process's AS-scope link state database (LSDB). The LSDB contains the AS-scope link state advertisements from throughout the areas that the device is attached to. | 1.3.6.1.2.1.191.1.3 | not-accessible | current | |
| ospfv3AsLsdbEntry OBJECT-TYPE A single AS-scope link state advertisement. | 1.3.6.1.2.1.191.1.3.1 | not-accessible | current | |
| ospfv3AsLsdbType OBJECT-TYPE The type of the link state advertisement. Each link state type has a separate advertisement format. AS-scope LSAs not recognized by the router may be stored in the database. | 1.3.6.1.2.1.191.1.3.1.1 | Unsigned32 (0..4294967295) | not-accessible | current |
| ospfv3AsLsdbRouterId OBJECT-TYPE The 32-bit number that uniquely identifies the originating router in the Autonomous System. | 1.3.6.1.2.1.191.1.3.1.2 | Ospfv3RouterIdTC | not-accessible | current |
| ospfv3AsLsdbLsid OBJECT-TYPE The Link State ID is an LS type-specific field containing a unique identifier; it identifies the piece of the routing domain that is being described by the advertisement. In contrast to OSPFv2, the LSID has no addressing semantics. | 1.3.6.1.2.1.191.1.3.1.3 | Ospfv3LsIdTC | not-accessible | current |
| ospfv3AsLsdbSequence OBJECT-TYPE The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number, the more recent the advertisement. | 1.3.6.1.2.1.191.1.3.1.4 | Ospfv3LsaSequenceTC | read-only | current |
| ospfv3AsLsdbAge OBJECT-TYPE This field is the age of the link state advertisement in seconds. The high-order bit of the LS age field is considered the DoNotAge bit for support of on-demand circuits. | 1.3.6.1.2.1.191.1.3.1.5 | Ospfv3LsaAgeTC | read-only | current |
| ospfv3AsLsdbChecksum OBJECT-TYPE This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum. | 1.3.6.1.2.1.191.1.3.1.6 | Integer32 | read-only | current |
| ospfv3AsLsdbAdvertisement OBJECT-TYPE The entire link state advertisement, including its header. | 1.3.6.1.2.1.191.1.3.1.7 | OCTET STRING (SIZE(1..65535)) | read-only | current |
| ospfv3AsLsdbTypeKnown OBJECT-TYPE The value true (1) indicates that the LSA type is recognized by this router. | 1.3.6.1.2.1.191.1.3.1.8 | TruthValue | read-only | current |
| ospfv3AreaLsdbTable OBJECT-TYPE The OSPFv3 Process's Area-scope LSDB. The LSDB contains the Area-scope link state advertisements from throughout the area that the device is attached to. | 1.3.6.1.2.1.191.1.4 | not-accessible | current | |
| ospfv3AreaLsdbEntry OBJECT-TYPE A single Area-scope link state advertisement. | 1.3.6.1.2.1.191.1.4.1 | not-accessible | current | |
| ospfv3AreaLsdbAreaId OBJECT-TYPE The 32-bit identifier of the Area from which the LSA was received. | 1.3.6.1.2.1.191.1.4.1.1 | Ospfv3AreaIdTC | not-accessible | current |
| ospfv3AreaLsdbType OBJECT-TYPE The type of the link state advertisement. Each link state type has a separate advertisement format. Area-scope LSAs unrecognized by the router are also stored in this database. | 1.3.6.1.2.1.191.1.4.1.2 | Unsigned32 (0..4294967295) | not-accessible | current |
| ospfv3AreaLsdbRouterId OBJECT-TYPE The 32-bit number that uniquely identifies the originating router in the Autonomous System. | 1.3.6.1.2.1.191.1.4.1.3 | Ospfv3RouterIdTC | not-accessible | current |
| ospfv3AreaLsdbLsid OBJECT-TYPE The Link State ID is an LS type-specific field containing a unique identifier; it identifies the piece of the routing domain that is being described by the advertisement. In contrast to OSPFv2, the LSID has no addressing semantics. | 1.3.6.1.2.1.191.1.4.1.4 | Ospfv3LsIdTC | not-accessible | current |
| ospfv3AreaLsdbSequence OBJECT-TYPE The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number, the more recent the advertisement. | 1.3.6.1.2.1.191.1.4.1.5 | Ospfv3LsaSequenceTC | read-only | current |
| ospfv3AreaLsdbAge OBJECT-TYPE This field is the age of the link state advertisement in seconds. The high-order bit of the LS age field is considered the DoNotAge bit for support of on-demand circuits. | 1.3.6.1.2.1.191.1.4.1.6 | Ospfv3LsaAgeTC | read-only | current |
| ospfv3AreaLsdbChecksum OBJECT-TYPE This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum. | 1.3.6.1.2.1.191.1.4.1.7 | Integer32 | read-only | current |
| ospfv3AreaLsdbAdvertisement OBJECT-TYPE The entire link state advertisement, including its header. | 1.3.6.1.2.1.191.1.4.1.8 | OCTET STRING (SIZE(1..65535)) | read-only | current |
| ospfv3AreaLsdbTypeKnown OBJECT-TYPE The value true (1) indicates that the LSA type is recognized by this router. | 1.3.6.1.2.1.191.1.4.1.9 | TruthValue | read-only | current |
| ospfv3LinkLsdbTable OBJECT-TYPE The OSPFv3 Process's Link-scope LSDB for non-virtual interfaces. The LSDB contains the Link-scope link state advertisements from the interfaces that the device is attached to. | 1.3.6.1.2.1.191.1.5 | not-accessible | current | |
| ospfv3LinkLsdbEntry OBJECT-TYPE A single Link-scope link state advertisement. | 1.3.6.1.2.1.191.1.5.1 | not-accessible | current | |
| ospfv3LinkLsdbIfIndex OBJECT-TYPE The identifier of the link from which the LSA was received. | 1.3.6.1.2.1.191.1.5.1.1 | InterfaceIndex | not-accessible | current |
| ospfv3LinkLsdbIfInstId OBJECT-TYPE The identifier of the interface instance from which the LSA was received. | 1.3.6.1.2.1.191.1.5.1.2 | Ospfv3IfInstIdTC | not-accessible | current |
| ospfv3LinkLsdbType OBJECT-TYPE The type of the link state advertisement. Each link state type has a separate advertisement format. Link-scope LSAs unrecognized by the router are also stored in this database. | 1.3.6.1.2.1.191.1.5.1.3 | Unsigned32 (0..4294967295) | not-accessible | current |
| ospfv3LinkLsdbRouterId OBJECT-TYPE The 32-bit number that uniquely identifies the originating router in the Autonomous System. | 1.3.6.1.2.1.191.1.5.1.4 | Ospfv3RouterIdTC | not-accessible | current |
| ospfv3LinkLsdbLsid OBJECT-TYPE The Link State ID is an LS type-specific field containing a unique identifier; it identifies the piece of the routing domain that is being described by the advertisement. In contrast to OSPFv2, the LSID has no addressing semantics. However, in OSPFv3 the Link State ID always contains the flooding scope of the LSA. | 1.3.6.1.2.1.191.1.5.1.5 | Ospfv3LsIdTC | not-accessible | current |
| ospfv3LinkLsdbSequence OBJECT-TYPE The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number, the more recent the advertisement. | 1.3.6.1.2.1.191.1.5.1.6 | Ospfv3LsaSequenceTC | read-only | current |
| ospfv3LinkLsdbAge OBJECT-TYPE This field is the age of the link state advertisement in seconds. The high-order bit of the LS age field is considered the DoNotAge bit for support of on-demand circuits. | 1.3.6.1.2.1.191.1.5.1.7 | Ospfv3LsaAgeTC | read-only | current |
| ospfv3LinkLsdbChecksum OBJECT-TYPE This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum. | 1.3.6.1.2.1.191.1.5.1.8 | Integer32 | read-only | current |
| ospfv3LinkLsdbAdvertisement OBJECT-TYPE The entire link state advertisement, including its header. | 1.3.6.1.2.1.191.1.5.1.9 | OCTET STRING (SIZE(1..65535)) | read-only | current |
| ospfv3LinkLsdbTypeKnown OBJECT-TYPE The value true (1) indicates that the LSA type is recognized by this router. | 1.3.6.1.2.1.191.1.5.1.10 | TruthValue | read-only | current |
| ospfv3HostTable OBJECT-TYPE The Host/Metric Table indicates what hosts are directly attached to the router and their corresponding metrics. | 1.3.6.1.2.1.191.1.6 | not-accessible | current | |
| ospfv3HostEntry OBJECT-TYPE A metric to be advertised when a given host is reachable. The information in this table is persistent, and when written, the entity SHOULD save the change to non-volatile storage. | 1.3.6.1.2.1.191.1.6.1 | not-accessible | current | |
| ospfv3HostAddressType OBJECT-TYPE The address type of ospfv3HostAddress. Only IPv6 global address type is expected. | 1.3.6.1.2.1.191.1.6.1.1 | InetAddressType | not-accessible | current |
| ospfv3HostAddress OBJECT-TYPE The IPv6 address of the host. Must be an IPv6 global address. | 1.3.6.1.2.1.191.1.6.1.2 | InetAddress | not-accessible | current |
| ospfv3HostMetric OBJECT-TYPE The metric to be advertised. | 1.3.6.1.2.1.191.1.6.1.3 | Metric | read-create | current |
| ospfv3HostRowStatus OBJECT-TYPE This object permits management of the table by facilitating actions such as row creation, construction, and destruction. The value of this object has no effect on whether other objects in this conceptual row can be modified. | 1.3.6.1.2.1.191.1.6.1.4 | RowStatus | read-create | current |
| ospfv3HostAreaID OBJECT-TYPE The Area the host entry is to be found within. By default, the area for the subsuming OSPFv3 interface, or Area 0 if there is no subsuming interface. | 1.3.6.1.2.1.191.1.6.1.5 | Ospfv3AreaIdTC | read-create | current |
| ospfv3IfTable OBJECT-TYPE The OSPFv3 Interface Table describes the interfaces from the viewpoint of OSPFv3. | 1.3.6.1.2.1.191.1.7 | not-accessible | current | |
| ospfv3IfEntry OBJECT-TYPE The OSPFv3 Interface Entry describes one interface from the viewpoint of OSPFv3. The information in this table is persistent, and when written, the entity SHOULD save the change to non-volatile storage. | 1.3.6.1.2.1.191.1.7.1 | not-accessible | current | |
| ospfv3IfIndex OBJECT-TYPE The interface index of this OSPFv3 interface. It corresponds to the interface index of the IPv6 interface on which OSPFv3 is configured. | 1.3.6.1.2.1.191.1.7.1.1 | InterfaceIndex | not-accessible | current |
| ospfv3IfInstId OBJECT-TYPE Enables multiple interface instances of OSPFv3 to be run over a single link. Each interface instance would be assigned a separate ID. This ID has local link significance only. | 1.3.6.1.2.1.191.1.7.1.2 | Ospfv3IfInstIdTC | not-accessible | current |
| ospfv3IfAreaId OBJECT-TYPE A 32-bit integer uniquely identifying the area to which the interface connects. Area ID 0 is used for the OSPFv3 backbone. | 1.3.6.1.2.1.191.1.7.1.3 | Ospfv3AreaIdTC | read-create | current |
| ospfv3IfType OBJECT-TYPE The OSPFv3 interface type. | 1.3.6.1.2.1.191.1.7.1.4 | INTEGER {broadcast(1), nbma(2), pointToPoint(3), pointToMultipoint(5)} | read-create | current |
| ospfv3IfAdminStatus OBJECT-TYPE The OSPFv3 interface's administrative status. The value formed on the interface; the interface will be advertised as an internal route to some area. The value 'disabled' denotes that the interface is external to OSPFv3. Note that a value of 'disabled' for the object ospfv3AdminStatus will override a value of 'enabled' for the interface. | 1.3.6.1.2.1.191.1.7.1.5 | Status | read-create | current |
| ospfv3IfRtrPriority OBJECT-TYPE The priority of this interface. Used in multi-access networks, this field is used in the designated-router election algorithm. The value 0 signifies that the router is not eligible to become the Designated Router on this particular network. In the event of a tie in this value, routers will use their Router ID as a tie breaker. | 1.3.6.1.2.1.191.1.7.1.6 | DesignatedRouterPriority | read-create | current |
| ospfv3IfTransitDelay OBJECT-TYPE The estimated number of seconds it takes to transmit a Link State Update packet over this interface. LSAs contained in the update packet must have their age incremented by this amount before transmission. This value should take into account the transmission and propagation delays of the interface. | 1.3.6.1.2.1.191.1.7.1.7 | Ospfv3UpToRefreshIntervalTC | read-create | current |
| ospfv3IfRetransInterval OBJECT-TYPE The number of seconds between link state advertisement retransmissions for adjacencies belonging to this interface. This value is also used when retransmitting database description and Link State Request packets. | 1.3.6.1.2.1.191.1.7.1.8 | Ospfv3UpToRefreshIntervalTC | read-create | current |
| ospfv3IfHelloInterval OBJECT-TYPE The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for all routers attached to a common network. | 1.3.6.1.2.1.191.1.7.1.9 | HelloRange | read-create | current |
| ospfv3IfRtrDeadInterval OBJECT-TYPE The number of seconds that a router's Hello packets have not been seen before its neighbors declare the router down on the interface. This should be some multiple of the Hello interval. This value must be the same for all routers attached to a common network. | 1.3.6.1.2.1.191.1.7.1.10 | Ospfv3DeadIntervalRangeTC | read-create | current |
| ospfv3IfPollInterval OBJECT-TYPE The larger time interval, in seconds, between the Hello packets sent to an inactive, non-broadcast multi-access neighbor. | 1.3.6.1.2.1.191.1.7.1.11 | Unsigned32 | read-create | current |
| ospfv3IfState OBJECT-TYPE The OSPFv3 interface state. An interface may be in standby state if there are multiple interfaces on the link and another interface is active. The interface may be in Down state if the underlying IPv6 interface is down or if the admin status is 'disabled' either globally or for the interface. | 1.3.6.1.2.1.191.1.7.1.12 | INTEGER {down(1), loopback(2), waiting(3), pointToPoint(4), designatedRouter(5), backupDesignatedRouter(6), otherDesignatedRouter(7), standby(8)} | read-only | current |
| ospfv3IfDesignatedRouter OBJECT-TYPE The Router ID of the Designated Router. | 1.3.6.1.2.1.191.1.7.1.13 | Ospfv3RouterIdTC | read-only | current |
| ospfv3IfBackupDesignatedRouter OBJECT-TYPE The Router ID of the Backup Designated Router. | 1.3.6.1.2.1.191.1.7.1.14 | Ospfv3RouterIdTC | read-only | current |
| ospfv3IfEvents OBJECT-TYPE The number of times this OSPFv3 interface has changed its state or an error has occurred. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times as indicated by the value of ospfv3DiscontinuityTime. | 1.3.6.1.2.1.191.1.7.1.15 | Counter32 | read-only | current |
| ospfv3IfRowStatus OBJECT-TYPE This object permits management of the table by facilitating actions such as row creation, construction, and destruction. The value of this object has no effect on whether other objects in this conceptual row can be modified. | 1.3.6.1.2.1.191.1.7.1.16 | RowStatus | read-create | current |
| ospfv3IfDemand OBJECT-TYPE Indicates whether Demand OSPFv3 procedures (Hello suppression to FULL neighbors and setting the DoNotAge flag on propagated LSAs) should be performed on this interface. | 1.3.6.1.2.1.191.1.7.1.17 | TruthValue | read-create | current |
| ospfv3IfMetricValue OBJECT-TYPE The metric assigned to this interface. The default value of the metric is 'Reference Bandwidth / ifSpeed'. The value of the reference bandwidth can be set in the ospfv3ReferenceBandwidth object. | 1.3.6.1.2.1.191.1.7.1.18 | Metric | read-create | current |
| ospfv3IfLinkScopeLsaCount OBJECT-TYPE The total number of Link-scope link state advertisements in this link's link state database. | 1.3.6.1.2.1.191.1.7.1.19 | Gauge32 | read-only | current |
| ospfv3IfLinkLsaCksumSum OBJECT-TYPE The 32-bit unsigned sum of the Link-scope link state advertisements' LS checksums contained in this link's link state database. The sum can be used to determine if there has been a change in a router's link state database or to compare the link state database of two routers. | 1.3.6.1.2.1.191.1.7.1.20 | Unsigned32 | read-only | current |
| ospfv3IfDemandNbrProbe OBJECT-TYPE Indicates whether or not neighbor probing is enabled to determine whether or not the neighbor is inactive. Neighbor probing is disabled by default. | 1.3.6.1.2.1.191.1.7.1.21 | TruthValue | read-create | current |
| ospfv3IfDemandNbrProbeRetransLimit OBJECT-TYPE The number of consecutive LSA retransmissions before the neighbor is deemed inactive and the neighbor adjacency is brought down. | 1.3.6.1.2.1.191.1.7.1.22 | Unsigned32 | read-create | current |
| ospfv3IfDemandNbrProbeInterval OBJECT-TYPE Defines how often the neighbor will be probed. | 1.3.6.1.2.1.191.1.7.1.23 | Unsigned32 | read-create | current |
| ospfv3IfTEDisabled OBJECT-TYPE Indicates whether or not traffic engineering is disabled on the interface when traffic engineering is enabled in the area where the interface is attached. The object is set to the value true (1) to disable traffic engineering on the interface. Traffic engineering is enabled by default on the interface when traffic engineering is enabled in the area where the interface is attached. | 1.3.6.1.2.1.191.1.7.1.24 | TruthValue | read-create | current |
| ospfv3IfLinkLSASuppression OBJECT-TYPE Specifies whether or not link LSA origination is suppressed for broadcast or NBMA interface types. The object is set to value true (1) to suppress the origination. | 1.3.6.1.2.1.191.1.7.1.25 | TruthValue | read-create | current |
| ospfv3VirtIfTable OBJECT-TYPE Information about this router's virtual interfaces that the OSPFv3 Process is configured to carry on. | 1.3.6.1.2.1.191.1.8 | not-accessible | current | |
| ospfv3VirtIfEntry OBJECT-TYPE Information about a single virtual interface. The information in this table is persistent, and when written, the entity SHOULD save the change to non-volatile storage. | 1.3.6.1.2.1.191.1.8.1 | not-accessible | current | |
| ospfv3VirtIfAreaId OBJECT-TYPE The transit area that the virtual link traverses. By definition, this is not Area 0. | 1.3.6.1.2.1.191.1.8.1.1 | Ospfv3AreaIdTC | not-accessible | current |
| ospfv3VirtIfNeighbor OBJECT-TYPE The Router ID of the virtual neighbor. | 1.3.6.1.2.1.191.1.8.1.2 | Ospfv3RouterIdTC | not-accessible | current |
| ospfv3VirtIfIndex OBJECT-TYPE The local interface index assigned by the OSPFv3 Process to this OSPFv3 virtual interface. It is advertised in Hellos sent over the virtual link and in the router's router-LSAs. | 1.3.6.1.2.1.191.1.8.1.3 | InterfaceIndex | read-only | current |
| ospfv3VirtIfInstId OBJECT-TYPE The local Interface Instance ID assigned by the OSPFv3 Process to this OSPFv3 virtual interface. | 1.3.6.1.2.1.191.1.8.1.4 | Ospfv3IfInstIdTC | read-only | current |
| ospfv3VirtIfTransitDelay OBJECT-TYPE The estimated number of seconds it takes to transmit a Link State Update packet over this interface. | 1.3.6.1.2.1.191.1.8.1.5 | Ospfv3UpToRefreshIntervalTC | read-create | current |
| ospfv3VirtIfRetransInterval OBJECT-TYPE The number of seconds between link state advertisement retransmissions for adjacencies belonging to this interface. This value is also used when retransmitting database description and Link State Request packets. This value should be well over the expected round-trip time. | 1.3.6.1.2.1.191.1.8.1.6 | Ospfv3UpToRefreshIntervalTC | read-create | current |
| ospfv3VirtIfHelloInterval OBJECT-TYPE The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for the virtual neighbor. | 1.3.6.1.2.1.191.1.8.1.7 | HelloRange | read-create | current |
| ospfv3VirtIfRtrDeadInterval OBJECT-TYPE The number of seconds that a router's Hello packets have not been seen before its neighbors declare the router down. This should be some multiple of the Hello interval. This value must be the same for the virtual neighbor. | 1.3.6.1.2.1.191.1.8.1.8 | Ospfv3DeadIntervalRangeTC | read-create | current |
| ospfv3VirtIfState OBJECT-TYPE OSPF virtual interface states. The same encoding as the ospfV3IfTable is used. | 1.3.6.1.2.1.191.1.8.1.9 | INTEGER {down(1), pointToPoint(4)} | read-only | current |
| ospfv3VirtIfEvents OBJECT-TYPE The number of state changes or error events on this virtual link. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times as indicated by the value of ospfv3DiscontinuityTime. | 1.3.6.1.2.1.191.1.8.1.10 | Counter32 | read-only | current |
| ospfv3VirtIfRowStatus OBJECT-TYPE This object permits management of the table by facilitating actions such as row creation, construction, and destruction. The value of this object has no effect on whether other objects in this conceptual row can be modified. | 1.3.6.1.2.1.191.1.8.1.11 | RowStatus | read-create | current |
| ospfv3VirtIfLinkScopeLsaCount OBJECT-TYPE The total number of Link-scope link state advertisements in this virtual link's link state database. | 1.3.6.1.2.1.191.1.8.1.12 | Gauge32 | read-only | current |
| ospfv3VirtIfLinkLsaCksumSum OBJECT-TYPE The 32-bit unsigned sum of the Link-scope link state advertisements' LS checksums contained in this virtual link's link state database. The sum can be used to determine if there has been a change in a router's link state database or to compare the link state database of two routers. | 1.3.6.1.2.1.191.1.8.1.13 | Unsigned32 | read-only | current |
| ospfv3NbrTable OBJECT-TYPE A table describing all neighbors in the locality of the OSPFv3 router. | 1.3.6.1.2.1.191.1.9 | not-accessible | current | |
| ospfv3NbrEntry OBJECT-TYPE The information regarding a single neighbor. | 1.3.6.1.2.1.191.1.9.1 | not-accessible | current | |
| ospfv3NbrIfIndex OBJECT-TYPE The Local Link ID of the link over which the neighbor can be reached. | 1.3.6.1.2.1.191.1.9.1.1 | InterfaceIndex | not-accessible | current |
| ospfv3NbrIfInstId OBJECT-TYPE Interface instance over which the neighbor can be reached. This ID has local link significance only. | 1.3.6.1.2.1.191.1.9.1.2 | Ospfv3IfInstIdTC | not-accessible | current |
| ospfv3NbrRtrId OBJECT-TYPE A 32-bit unsigned integer uniquely identifying the neighboring router in the Autonomous System. | 1.3.6.1.2.1.191.1.9.1.3 | Ospfv3RouterIdTC | not-accessible | current |
| ospfv3NbrAddressType OBJECT-TYPE The address type of ospfv3NbrAddress. Only IPv6 addresses without zone index are expected. | 1.3.6.1.2.1.191.1.9.1.4 | InetAddressType | read-only | current |
| ospfv3NbrAddress OBJECT-TYPE The IPv6 address of the neighbor associated with the local link. | 1.3.6.1.2.1.191.1.9.1.5 | InetAddress | read-only | current |
| ospfv3NbrOptions OBJECT-TYPE A bit mask corresponding to the neighbor's options field. | 1.3.6.1.2.1.191.1.9.1.6 | Integer32 | read-only | current |
| ospfv3NbrPriority OBJECT-TYPE The priority of this neighbor in the designated- router election algorithm. The value 0 signifies that the neighbor is not eligible to become the Designated Router on this particular network. | 1.3.6.1.2.1.191.1.9.1.7 | DesignatedRouterPriority | read-only | current |
| ospfv3NbrState OBJECT-TYPE The state of the relationship with this neighbor. | 1.3.6.1.2.1.191.1.9.1.8 | INTEGER {down(1), attempt(2), init(3), twoWay(4), exchangeStart(5), exchange(6), loading(7), full(8)} | read-only | current |
| ospfv3NbrEvents OBJECT-TYPE The number of times this neighbor relationship has changed state or an error has occurred. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times as indicated by the value of ospfv3DiscontinuityTime. | 1.3.6.1.2.1.191.1.9.1.9 | Counter32 | read-only | current |
| ospfv3NbrLsRetransQLen OBJECT-TYPE The current length of the retransmission queue. | 1.3.6.1.2.1.191.1.9.1.10 | Gauge32 | read-only | current |
| ospfv3NbrHelloSuppressed OBJECT-TYPE Indicates whether Hellos are being suppressed to the neighbor. | 1.3.6.1.2.1.191.1.9.1.11 | TruthValue | read-only | current |
| ospfv3NbrIfId OBJECT-TYPE The Interface ID that the neighbor advertises in its Hello packets on this link, that is, the neighbor's local interface index. | 1.3.6.1.2.1.191.1.9.1.12 | InterfaceIndex | read-only | current |
| ospfv3NbrRestartHelperStatus OBJECT-TYPE Indicates whether the router is acting as a graceful restart helper for the neighbor. | 1.3.6.1.2.1.191.1.9.1.13 | INTEGER {notHelping(1), helping(2)} | read-only | current |
| ospfv3NbrRestartHelperAge OBJECT-TYPE Remaining time in current OSPF graceful restart interval, if the router is acting as a restart helper for the neighbor. | 1.3.6.1.2.1.191.1.9.1.14 | Ospfv3UpToRefreshIntervalTC | read-only | current |
| ospfv3NbrRestartHelperExitReason OBJECT-TYPE Describes the outcome of the last attempt at acting as a graceful restart helper for the neighbor. none: no restart has yet been attempted. inProgress: a restart attempt is currently underway. completed: the last restart completed successfully. timedOut: the last restart timed out. topologyChanged: the last restart was aborted due to a topology change. | 1.3.6.1.2.1.191.1.9.1.15 | INTEGER {none(1), inProgress(2), completed(3), timedOut(4), topologyChanged(5)} | read-only | current |
| ospfv3CfgNbrTable OBJECT-TYPE A table describing all configured neighbors. The Configured Neighbors table just gives OSPFv3 information for sending OSPFv3 packets to potential neighbors and is typically used on NBMA and Point-to-Multipoint networks. Once a Hello is received from a neighbor in the Configured Neighbor table, an entry for that neighbor is created in the Neighbor table and adjacency state is maintained there. Neighbors on multi-access or Point-to-Point networks can use multicast addressing, so only Neighbor table entries are created for them. | 1.3.6.1.2.1.191.1.10 | not-accessible | current | |
| ospfv3CfgNbrEntry OBJECT-TYPE The information regarding a single configured neighbor. The information in this table is persistent, and when written, the entity SHOULD save the change to non-volatile storage. | 1.3.6.1.2.1.191.1.10.1 | not-accessible | current | |
| ospfv3CfgNbrIfIndex OBJECT-TYPE The Local Link ID of the link over which the neighbor can be reached. | 1.3.6.1.2.1.191.1.10.1.1 | InterfaceIndex | not-accessible | current |
| ospfv3CfgNbrIfInstId OBJECT-TYPE Interface instance over which the neighbor can be reached. This ID has local link significance only. | 1.3.6.1.2.1.191.1.10.1.2 | Ospfv3IfInstIdTC | not-accessible | current |
| ospfv3CfgNbrAddressType OBJECT-TYPE The address type of ospfv3NbrAddress. Only IPv6 addresses without zone index are expected. | 1.3.6.1.2.1.191.1.10.1.3 | InetAddressType | not-accessible | current |
| ospfv3CfgNbrAddress OBJECT-TYPE The IPv6 address of the neighbor associated with the local link. | 1.3.6.1.2.1.191.1.10.1.4 | InetAddress | not-accessible | current |
| ospfv3CfgNbrPriority OBJECT-TYPE The priority of this neighbor in the designated- router election algorithm. The value 0 signifies that the neighbor is not eligible to become the Designated Router on this particular network. | 1.3.6.1.2.1.191.1.10.1.5 | DesignatedRouterPriority | read-create | current |
| ospfv3CfgNbrRowStatus OBJECT-TYPE This object permits management of the table by facilitating actions such as row creation, construction, and destruction. The value of this object has no effect on whether other objects in this conceptual row can be modified. | 1.3.6.1.2.1.191.1.10.1.6 | RowStatus | read-create | current |
| ospfv3VirtNbrTable OBJECT-TYPE A table describing all virtual neighbors. | 1.3.6.1.2.1.191.1.11 | not-accessible | current | |
| ospfv3VirtNbrEntry OBJECT-TYPE Virtual neighbor information. | 1.3.6.1.2.1.191.1.11.1 | not-accessible | current | |
| ospfv3VirtNbrArea OBJECT-TYPE The transit area Identifier. | 1.3.6.1.2.1.191.1.11.1.1 | Ospfv3AreaIdTC | not-accessible | current |
| ospfv3VirtNbrRtrId OBJECT-TYPE A 32-bit integer uniquely identifying the neighboring router in the Autonomous System. | 1.3.6.1.2.1.191.1.11.1.2 | Ospfv3RouterIdTC | not-accessible | current |
| ospfv3VirtNbrIfIndex OBJECT-TYPE The local Interface ID for the virtual link over which the neighbor can be reached. | 1.3.6.1.2.1.191.1.11.1.3 | InterfaceIndex | read-only | current |
| ospfv3VirtNbrIfInstId OBJECT-TYPE The interface instance for the virtual link over which the neighbor can be reached. | 1.3.6.1.2.1.191.1.11.1.4 | Ospfv3IfInstIdTC | read-only | current |
| ospfv3VirtNbrAddressType OBJECT-TYPE The address type of ospfv3VirtNbrAddress. Only IPv6 addresses without zone index are expected. | 1.3.6.1.2.1.191.1.11.1.5 | InetAddressType | read-only | current |
| ospfv3VirtNbrAddress OBJECT-TYPE The IPv6 address advertised by this virtual neighbor. It must be a global scope address. | 1.3.6.1.2.1.191.1.11.1.6 | InetAddress | read-only | current |
| ospfv3VirtNbrOptions OBJECT-TYPE A bit mask corresponding to the neighbor's options field. | 1.3.6.1.2.1.191.1.11.1.7 | Integer32 | read-only | current |
| ospfv3VirtNbrState OBJECT-TYPE The state of the virtual neighbor relationship. | 1.3.6.1.2.1.191.1.11.1.8 | INTEGER {down(1), attempt(2), init(3), twoWay(4), exchangeStart(5), exchange(6), loading(7), full(8)} | read-only | current |
| ospfv3VirtNbrEvents OBJECT-TYPE The number of times this virtual link has changed its state or an error has occurred. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times as indicated by the value of ospfv3DiscontinuityTime. | 1.3.6.1.2.1.191.1.11.1.9 | Counter32 | read-only | current |
| ospfv3VirtNbrLsRetransQLen OBJECT-TYPE The current length of the retransmission queue. | 1.3.6.1.2.1.191.1.11.1.10 | Gauge32 | read-only | current |
| ospfv3VirtNbrHelloSuppressed OBJECT-TYPE Indicates whether Hellos are being suppressed to the neighbor. | 1.3.6.1.2.1.191.1.11.1.11 | TruthValue | read-only | current |
| ospfv3VirtNbrIfId OBJECT-TYPE The Interface ID that the neighbor advertises in its Hello packets on this virtual link, that is, the neighbor's local Interface ID. | 1.3.6.1.2.1.191.1.11.1.12 | InterfaceIndex | read-only | current |
| ospfv3VirtNbrRestartHelperStatus OBJECT-TYPE Indicates whether the router is acting as a graceful restart helper for the neighbor. | 1.3.6.1.2.1.191.1.11.1.13 | INTEGER {notHelping(1), helping(2)} | read-only | current |
| ospfv3VirtNbrRestartHelperAge OBJECT-TYPE Remaining time in the current OSPF graceful restart interval, if the router is acting as a restart helper for the neighbor. | 1.3.6.1.2.1.191.1.11.1.14 | Ospfv3UpToRefreshIntervalTC | read-only | current |
| ospfv3VirtNbrRestartHelperExitReason OBJECT-TYPE Describes the outcome of the last attempt at acting as a graceful restart helper for the neighbor. none: no restart has yet been attempted. inProgress: a restart attempt is currently underway. completed: the last restart completed successfully. timedOut: the last restart timed out. topologyChanged: the last restart was aborted due to a topology change. | 1.3.6.1.2.1.191.1.11.1.15 | INTEGER {none(1), inProgress(2), completed(3), timedOut(4), topologyChanged(5)} | read-only | current |
| ospfv3AreaAggregateTable OBJECT-TYPE The Area Aggregate Table acts as an adjunct to the Area Table. It describes those address aggregates that are configured to be propagated from an area. Its purpose is to reduce the amount of information that is known beyond an area's borders. A range of IPv6 prefixes specified by a prefix / prefix length pair. Note that if ranges are configured such that one range subsumes another range, the most specific match is the preferred one. | 1.3.6.1.2.1.191.1.12 | not-accessible | current | |
| ospfv3AreaAggregateEntry OBJECT-TYPE A single area aggregate entry. Information in this table is persistent, and when this object is written, the entity SHOULD save the change to non-volatile storage. | 1.3.6.1.2.1.191.1.12.1 | not-accessible | current | |
| ospfv3AreaAggregateAreaID OBJECT-TYPE The area the Address Aggregate is to be found within. | 1.3.6.1.2.1.191.1.12.1.1 | Ospfv3AreaIdTC | not-accessible | current |
| ospfv3AreaAggregateAreaLsdbType OBJECT-TYPE The type of the Address Aggregate. This field specifies the Area LSDB type that this Address Aggregate applies to. | 1.3.6.1.2.1.191.1.12.1.2 | INTEGER {interAreaPrefixLsa(8195), nssaExternalLsa(8199)} | not-accessible | current |
| ospfv3AreaAggregatePrefixType OBJECT-TYPE The prefix type of ospfv3AreaAggregatePrefix. Only IPv6 addresses are expected. | 1.3.6.1.2.1.191.1.12.1.3 | InetAddressType | not-accessible | current |
| ospfv3AreaAggregatePrefix OBJECT-TYPE The IPv6 prefix. | 1.3.6.1.2.1.191.1.12.1.4 | InetAddress (SIZE(0..16)) | not-accessible | current |
| ospfv3AreaAggregatePrefixLength OBJECT-TYPE The length of the prefix (in bits). A prefix can not be shorter than 3 bits. | 1.3.6.1.2.1.191.1.12.1.5 | InetAddressPrefixLength (3..128) | not-accessible | current |
| ospfv3AreaAggregateRowStatus OBJECT-TYPE This object permits management of the table by facilitating actions such as row creation, construction, and destruction. The value of this object has no effect on whether other objects in this conceptual row can be modified. | 1.3.6.1.2.1.191.1.12.1.6 | RowStatus | read-create | current |
| ospfv3AreaAggregateEffect OBJECT-TYPE Prefixes subsumed by ranges will either trigger the advertisement of the indicated aggregate (advertiseMatching) or result in the prefix not being advertised at all outside the area. | 1.3.6.1.2.1.191.1.12.1.7 | INTEGER {advertiseMatching(1), doNotAdvertiseMatching(2)} | read-create | current |
| ospfv3AreaAggregateRouteTag OBJECT-TYPE This tag is advertised only in the summarized As-External LSA when summarizing from NSSA-LSAs to AS-External-LSAs. | 1.3.6.1.2.1.191.1.12.1.8 | Unsigned32 | read-create | current |
| ospfv3VirtLinkLsdbTable OBJECT-TYPE The OSPFv3 Process's Link-scope LSDB for virtual interfaces. The LSDB contains the Link-scope link state advertisements from virtual interfaces. | 1.3.6.1.2.1.191.1.13 | not-accessible | current | |
| ospfv3VirtLinkLsdbEntry OBJECT-TYPE A single Link-scope link state advertisement for a virtual interface. | 1.3.6.1.2.1.191.1.13.1 | not-accessible | current | |
| ospfv3VirtLinkLsdbIfAreaId OBJECT-TYPE The transit area that the virtual link traverses. By definition, this is not Area 0. | 1.3.6.1.2.1.191.1.13.1.1 | Ospfv3AreaIdTC | not-accessible | current |
| ospfv3VirtLinkLsdbIfNeighbor OBJECT-TYPE The Router ID of the virtual neighbor. | 1.3.6.1.2.1.191.1.13.1.2 | Ospfv3RouterIdTC | not-accessible | current |
| ospfv3VirtLinkLsdbType OBJECT-TYPE The type of the link state advertisement. Each link state type has a separate advertisement format. Link-scope LSAs unrecognized by the router are also stored in this database. | 1.3.6.1.2.1.191.1.13.1.3 | Unsigned32 (0..4294967295) | not-accessible | current |
| ospfv3VirtLinkLsdbRouterId OBJECT-TYPE The 32-bit number that uniquely identifies the originating router in the Autonomous System. | 1.3.6.1.2.1.191.1.13.1.4 | Ospfv3RouterIdTC | not-accessible | current |
| ospfv3VirtLinkLsdbLsid OBJECT-TYPE The Link State ID is an LS type-specific field containing a unique identifier; it identifies the piece of the routing domain that is being described by the advertisement. In contrast to OSPFv2, the LSID has no addressing semantics. | 1.3.6.1.2.1.191.1.13.1.5 | Ospfv3LsIdTC | not-accessible | current |
| ospfv3VirtLinkLsdbSequence OBJECT-TYPE The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number, the more recent the advertisement. | 1.3.6.1.2.1.191.1.13.1.6 | Ospfv3LsaSequenceTC | read-only | current |
| ospfv3VirtLinkLsdbAge OBJECT-TYPE This field is the age of the link state advertisement in seconds. The high-order bit of the LS age field is considered the DoNotAge bit for support of on-demand circuits. | 1.3.6.1.2.1.191.1.13.1.7 | Ospfv3LsaAgeTC | read-only | current |
| ospfv3VirtLinkLsdbChecksum OBJECT-TYPE This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum. | 1.3.6.1.2.1.191.1.13.1.8 | Integer32 | read-only | current |
| ospfv3VirtLinkLsdbAdvertisement OBJECT-TYPE The entire link state advertisement, including its header. | 1.3.6.1.2.1.191.1.13.1.9 | OCTET STRING (SIZE(1..65535)) | read-only | current |
| ospfv3VirtLinkLsdbTypeKnown OBJECT-TYPE The value true (1) indicates that the LSA type is recognized by this router. | 1.3.6.1.2.1.191.1.13.1.10 | TruthValue | read-only | current |
| ospfv3NotificationEntry OBJECT-IDENTITY | 1.3.6.1.2.1.191.1.14 | |||
| ospfv3ConfigErrorType OBJECT-TYPE Potential types of configuration conflicts. Used by the ospfv3ConfigError and ospfv3ConfigVirtError notifications. | 1.3.6.1.2.1.191.1.14.1 | INTEGER {badVersion(1), areaMismatch(2), unknownNbmaNbr(3), unknownVirtualNbr(4), helloIntervalMismatch(5), deadIntervalMismatch(6), optionMismatch(7), mtuMismatch(8), duplicateRouterId(9), noError(10)} | accessible-for-notify | current |
| ospfv3PacketType OBJECT-TYPE OSPFv3 packet types. | 1.3.6.1.2.1.191.1.14.2 | INTEGER {hello(1), dbDescript(2), lsReq(3), lsUpdate(4), lsAck(5), nullPacket(6)} | accessible-for-notify | current |
| ospfv3PacketSrc OBJECT-TYPE The IPv6 address of an inbound packet that cannot be identified by a neighbor instance. Only IPv6 addresses without zone index are expected. | 1.3.6.1.2.1.191.1.14.3 | InetAddressIPv6 | accessible-for-notify | current |
| ospfv3Conformance OBJECT-IDENTITY | 1.3.6.1.2.1.191.2 | |||
| ospfv3Groups OBJECT-IDENTITY | 1.3.6.1.2.1.191.2.1 | |||
| ospfv3Compliances OBJECT-IDENTITY | 1.3.6.1.2.1.191.2.2 |
Notifications
| Name | OID | Status |
|---|---|---|
| ospfv3VirtIfStateChange NOTIFICATION-TYPE An ospfv3VirtIfStateChange notification signifies that there has been a change in the state of an OSPFv3 virtual interface. This notification should be generated when the interface state regresses (e.g., goes from Point-to-Point to Down) or progresses to a terminal state (i.e., Point-to-Point). | 1.3.6.1.2.1.191.0.1 | current |
| ospfv3NbrStateChange NOTIFICATION-TYPE An ospfv3NbrStateChange notification signifies that there has been a change in the state of a non-virtual OSPFv3 neighbor. This notification should be generated when the neighbor state regresses (e.g., goes from Attempt or Full to 1-Way or Down) or progresses to a terminal state (e.g., 2-Way or Full). When a neighbor transitions from or to Full on non-broadcast multi-access and broadcast networks, the notification should be generated by the Designated Router. A Designated Router transitioning to Down will be noted by ospfIfStateChange. | 1.3.6.1.2.1.191.0.2 | current |
| ospfv3VirtNbrStateChange NOTIFICATION-TYPE An ospfv3VirtNbrStateChange notification signifies that there has been a change in the state of an OSPFv3 virtual neighbor. This notification should be generated when the neighbor state regresses (e.g., goes from Attempt or Full to 1-Way or Down) or progresses to a terminal state (e.g., Full). | 1.3.6.1.2.1.191.0.3 | current |
| ospfv3IfConfigError NOTIFICATION-TYPE An ospfv3IfConfigError notification signifies that a packet has been received on a non-virtual interface from a router whose configuration parameters conflict with this router's configuration parameters. Note that the event optionMismatch should cause a notification only if it prevents an adjacency from forming. | 1.3.6.1.2.1.191.0.4 | current |
| ospfv3VirtIfConfigError NOTIFICATION-TYPE An ospfv3VirtIfConfigError notification signifies that a packet has been received on a virtual interface from a router whose configuration parameters conflict with this router's configuration parameters. Note that the event optionMismatch should cause a notification only if it prevents an adjacency from forming. | 1.3.6.1.2.1.191.0.5 | current |
| ospfv3IfRxBadPacket NOTIFICATION-TYPE An ospfv3IfRxBadPacket notification signifies that an OSPFv3 packet that cannot be parsed has been received on a non-virtual interface. | 1.3.6.1.2.1.191.0.6 | current |
| ospfv3VirtIfRxBadPacket NOTIFICATION-TYPE An ospfv3VirtIfRxBadPacket notification signifies that an OSPFv3 packet that cannot be parsed has been received on a virtual interface. | 1.3.6.1.2.1.191.0.7 | current |
| ospfv3LsdbOverflow NOTIFICATION-TYPE An ospfv3LsdbOverflow notification signifies that the number of LSAs in the router's link state database has exceeded ospfv3ExtAreaLsdbLimit. | 1.3.6.1.2.1.191.0.8 | current |
| ospfv3LsdbApproachingOverflow NOTIFICATION-TYPE An ospfv3LsdbApproachingOverflow notification signifies that the number of LSAs in the router's link state database has exceeded ninety percent of ospfv3ExtAreaLsdbLimit. | 1.3.6.1.2.1.191.0.9 | current |
| ospfv3IfStateChange NOTIFICATION-TYPE An ospfv3IfStateChange notification signifies that there has been a change in the state of a non-virtual OSPFv3 interface. This notification should be generated when the interface state regresses (e.g., goes from DR to Down) or progresses to a terminal state (i.e., Point-to-Point, DR Other, DR, or Backup). | 1.3.6.1.2.1.191.0.10 | current |
| ospfv3NssaTranslatorStatusChange NOTIFICATION-TYPE An ospfv3NssaTranslatorStatusChange notification indicates that there has been a change in the router's ability to translate OSPFv3 NSSA LSAs into OSPFv3 External LSAs. This notification should be generated when the Translator Status transitions from or to any defined status on a per-area basis. | 1.3.6.1.2.1.191.0.11 | current |
| ospfv3RestartStatusChange NOTIFICATION-TYPE An ospfv3RestartStatusChange notification signifies that there has been a change in the graceful restart state for the router. This notification should be generated when the router restart status changes. | 1.3.6.1.2.1.191.0.12 | current |
| ospfv3NbrRestartHelperStatusChange NOTIFICATION-TYPE An ospfv3NbrRestartHelperStatusChange notification signifies that there has been a change in the graceful restart helper state for the neighbor. This notification should be generated when the neighbor restart helper status transitions for a neighbor. | 1.3.6.1.2.1.191.0.13 | current |
| ospfv3VirtNbrRestartHelperStatusChange NOTIFICATION-TYPE An ospfv3VirtNbrRestartHelperStatusChange notification signifies that there has been a change in the graceful restart helper state for the virtual neighbor. This notification should be generated when the virtual neighbor restart helper status transitions for a virtual neighbor. | 1.3.6.1.2.1.191.0.14 | current |
Conformance
| Name | OID | Status |
|---|---|---|
| ospfv3BasicGroup OBJECT-GROUP These objects are used for managing/monitoring OSPFv3 global parameters. | 1.3.6.1.2.1.191.2.1.1 | current |
| ospfv3AreaGroup OBJECT-GROUP These objects are used for OSPFv3 systems supporting areas. | 1.3.6.1.2.1.191.2.1.2 | current |
| ospfv3AsLsdbGroup OBJECT-GROUP These objects are used for OSPFv3 systems that display their AS-scope link state database. | 1.3.6.1.2.1.191.2.1.3 | current |
| ospfv3AreaLsdbGroup OBJECT-GROUP These objects are used for OSPFv3 systems that display their Area-scope link state database. | 1.3.6.1.2.1.191.2.1.4 | current |
| ospfv3LinkLsdbGroup OBJECT-GROUP These objects are used for OSPFv3 systems that display their Link-scope link state database for non-virtual interfaces. | 1.3.6.1.2.1.191.2.1.5 | current |
| ospfv3HostGroup OBJECT-GROUP These objects are used for OSPFv3 systems that support attached hosts. | 1.3.6.1.2.1.191.2.1.6 | current |
| ospfv3IfGroup OBJECT-GROUP These interface objects are used for managing/monitoring OSPFv3 interfaces. | 1.3.6.1.2.1.191.2.1.7 | current |
| ospfv3VirtIfGroup OBJECT-GROUP These virtual interface objects are used for managing/monitoring OSPFv3 virtual interfaces. | 1.3.6.1.2.1.191.2.1.8 | current |
| ospfv3NbrGroup OBJECT-GROUP These neighbor objects are used for managing/monitoring OSPFv3 neighbors. | 1.3.6.1.2.1.191.2.1.9 | current |
| ospfv3CfgNbrGroup OBJECT-GROUP These configured neighbor objects are used for managing/monitoring OSPFv3-configured neighbors. | 1.3.6.1.2.1.191.2.1.10 | current |
| ospfv3VirtNbrGroup OBJECT-GROUP These virtual neighbor objects are used for managing/monitoring OSPFv3 virtual neighbors. | 1.3.6.1.2.1.191.2.1.11 | current |
| ospfv3AreaAggregateGroup OBJECT-GROUP These area aggregate objects are required for aggregating OSPFv3 prefixes for summarization across areas. | 1.3.6.1.2.1.191.2.1.12 | current |
| ospfv3VirtLinkLsdbGroup OBJECT-GROUP These objects are used for OSPFv3 systems that display their Link-scope link state database for virtual interfaces. | 1.3.6.1.2.1.191.2.1.13 | current |
| ospfv3NotificationObjectGroup OBJECT-GROUP These objects are used to record notification parameters. | 1.3.6.1.2.1.191.2.1.14 | current |
| ospfv3NotificationGroup NOTIFICATION-GROUP This group is used for OSPFv3 notifications. | 1.3.6.1.2.1.191.2.1.15 | current |
| ospfv3FullCompliance MODULE-COMPLIANCE The compliance statement | 1.3.6.1.2.1.191.2.2.1 | current |
| ospfv3ReadOnlyCompliance MODULE-COMPLIANCE When this MIB module is implemented without support for read-create (i.e., in read-only mode), the implementation can claim read-only compliance. Such a device can then be monitored, but cannot be configured with this MIB. | 1.3.6.1.2.1.191.2.2.2 | current |