HMPRIV-MGMT-SNMP-MIB

TEXTUAL-CONVENTION

The Bridge-Identifier as used in the Spanning Tree or Null, if no valid data is available

TEXTUAL-CONVENTION

Status of the DIP switch.

TEXTUAL-CONVENTION

Severity code used in determining the SysLog Priority value.

TEXTUAL-CONVENTION

Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 2048 characters in length.

TEXTUAL-CONVENTION

Color of the LED

TEXTUAL-CONVENTION

The PTPClockIdentity type identifies a PTP clock. The PTPClockIdentity shall be in the IEEE EUI-64 format. For example: '008063FFFF000000'

TEXTUAL-CONVENTION

The PTPClockQuality represents the quality of a clock. The first octet represents the clock class. The second octet represents the clockAccuracy and the last two octets represent the offsetScaledLogVariance For example:

TEXTUAL-CONVENTION

The PTPPortIdentity type identifies a PTP port. The first 8 octets within this value specifies the ClockIdentity. The last 2 octetes within this value specifies the port number. For example: '00 80 63 FF FF 00 00 00 00 01'. ClockIdentity is '008063FFFF000000' and port number is '0001'

TEXTUAL-CONVENTION

The values of the octets for the subdomain name may be chosen from the set consisting of the values of the printable ASCII characters starting with hex value 0x21 (!) up to and including hex value 0x7E (~).

TEXTUAL-CONVENTION

The scaledNanoseconds member is the time interval expressed in units of nanoseconds and multiplied by 2^+16. Positive or negative time intervals outside the maximum range of this data type shall be encoded as the largest positive and negative values of the data type respectively. For example: 2.5 ns is expressed as: (hex) 0x0000 0000 0002 8000

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

The events of hmChassis.

OBJECT-IDENTITY

OBJECT-TYPE

Manufacturer-defined product identifier.

OBJECT-TYPE

This value is a string that contains at least the following data : SW: Version number of software CH: Version number of chassis BP: Version number of backplane

OBJECT-TYPE

The hmSysGroupCapacity is the number of groups that can be contained within the chassis. Within each managed chassis/switch, the groups are uniquely numbered in the range from 1 to hmSysGroupCapacity. Some groups may not be present in the chassis, in which case the actual number of groups present will be less than hmSysGroupCapacity. The number of groups present will never be greater than hmSysGroupCapacity.

OBJECT-TYPE

This string represents the current configuration of the chassis, encoded as an octet string. Each module is represented by a single octet. If the value of a single octet is the ascii representation of the character '1', it indicates that the module represented by that octet is present, if '0', the module is absent. The number of octets in the string is given by hmSysGroupCapacity. If the value of this variable changes, a hmGroupMapChange trap is sent.

OBJECT-TYPE

Maximum number of power supplies for this chassis. Within each managed chassis/switch, the groups are uniquely numbered in the range from 1 to hmSysMaxPowerSupply.

OBJECT-TYPE

Maximum number of fans for this chassis. Within each managed chassis/switch, the fans are uniquely numbered in the range from 0 to hmSysMaxFan.

OBJECT-TYPE

Maximum number of modules that an individual group can contain in this system.

OBJECT-TYPE

Maximum number of ports that an individual module can contain in this system.

OBJECT-TYPE

This table contains variables for a closer description of a group.

OBJECT-TYPE

The entry of the hmSysGroupTable.

OBJECT-TYPE

index to identify an interface card. This value is never greater than hmSysGroupCapacity.

OBJECT-TYPE

Type of interface card.

OBJECT-TYPE

Description of interface card.

OBJECT-TYPE

Hardware version of interface card.

OBJECT-TYPE

Software version of interface card.

OBJECT-TYPE

This string represents the current configuration of a group, encoded as an octet string. Each module is represented by a single octet. If the value of a single octet is the ascii representation of the character '1', it indicates that the module represented by that octet is present, if '0', the module is absent. If the character is 'C', then the card is configurable but absent. The ports can be configured and by setting hmSysModStatus to remove(3) the card can be logically removed. The number of bytes in the string is given by hmSysGroupModuleCapacity.

OBJECT-TYPE

This object, when read, always returns a value of other(1). A value of reset(2) has the same effect as a power-on sequence (coldstart). When set to resetStats(3), a reset of all statistic counters of the card's ports will be forced. Any other value results in a badValue status code.

OBJECT-TYPE

Result of the last activated action. A value of zero indicates that the result is ok. Bits set in the result indicate error conditions.

OBJECT-TYPE

Setting this variable to enable(1) separates the group from the rest of the chassis, so that it will act like a standalone-switch.

OBJECT-TYPE

The serial number provided by vendor (ASCII).

OBJECT-TYPE

Time in seconds until a reset(2) or hotRestart(10) that was triggered over the hmSysGroupAction object is executed. Writing a zero will cancel any scheduled reset.

OBJECT-TYPE

If a delayed reset is scheduled this object will incrementing from the start value to zero.

OBJECT-TYPE

This table contains variables for a closer description of a module.

OBJECT-TYPE

The entry of the hmSysModuleTable.

OBJECT-TYPE

index to identify an interface card. This value is never greater than hmSysGroupCapacity.

OBJECT-TYPE

index to identify a module on an interface card. This value is never greater than hmSysGroupModuleCapacity.

OBJECT-TYPE

Type of a module.

OBJECT-TYPE

Description of the module.

OBJECT-TYPE

version of the module.

OBJECT-TYPE

The numberOfPorts is the number of ports contained within the module. Within each module, the ports are uniquely numbered in the range from 1 to numberOfPorts.

OBJECT-TYPE

value of the first mauIndex used by the module.

OBJECT-TYPE

status of hot-pluggable modules, only for PowerMICE. If the value is physical(1), then the module is plugged in, if the value is configurable, the ports can be configured, but the card is absent, with the value remove(3) written to the agent the card can be logically removed.

OBJECT-TYPE

The serial number provided by vendor (ASCII).

OBJECT-TYPE

Enable or disable the module. If disabled, module plugged in this slot will not be activated.

OBJECT-TYPE

This table contains variables for each interface of the switch.

OBJECT-TYPE

The entry of the hmInterfaceTable.

OBJECT-TYPE

index to identify an interface card. This value is never greater than hmSysGroupCapacity.

OBJECT-TYPE

index to identify an interface within an interface card.

OBJECT-TYPE

Enable or disable spanning tree protocol.

OBJECT-TYPE

Describes the link type of the interface.

OBJECT-TYPE

This object, when read, always returns a value of noAction(1). When set to resetStats(2), a reset of all statistic counters within this interfacecard will be forced.

OBJECT-TYPE

The macaddress of the next switch agent reachable via this interface. If the value is 0:0:0:0:0:0, no other switch is seen via this interface.

OBJECT-TYPE

Enables or disables flow control per port

OBJECT-TYPE

This object is used to support the dot1dTrafficClassTable. It defines the thresholds of the available priority-classes. Starting at MACH Release 2.20 this variable is not used any more.

OBJECT-TYPE

User configurable textual description of the interface. On devices which support Power over Ethernet (IEEE 802.af), this object is mapped to pethPsePortType of the RFC3621 MIB.

OBJECT-TYPE

If the value of this variable is greater 0 then it belongs to the link aggregation instance with the same index. If the value is 0 no link aggregation uses this interface.

OBJECT-TYPE

Enable or disable Priority setting from IP TOS field.

OBJECT-TYPE

Broadcast rate: maximum number of broadcasts to be sent on this port within one second, use 0 for no limitation.

OBJECT-TYPE

The best estimate of the mean physical layer network utilization on this interface during the last sampling interval, in hundredths of a percent. The first historyControlInterval (rfc1757) of this interface is used as sampling interval.

OBJECT-TYPE

The interval in seconds over which the data is sampled for hmIfaceUtilization. This interval can be any number of seconds between 1 and 3600 (1 hour). The first historyControlInterval (rfc1757) of this interface is used as sampling interval.

OBJECT-TYPE

Enabled or disabled the BPDU guard functionality per port. If BPDU guard functionality are global enabled (hmSysStpBPDUGuardEnable=enable(1)), and BPDU guard are enabled per port (hmIfaceStpBpduGuardEnable=enable(1)) and (R)STP are globally enabled and an BPDU are received on the port, then hmIfaceStpBpduGuardStatus is set to true(1) for this port and IfAdminStatus for this port is set to down(2). Variable hmIfaceStpBpduGuardStatus can be reset to their original value (=false) with switching BPDU guard functionality globally off. IfAdminStatus can be reset to to their original values up() only manually.

OBJECT-TYPE

Advertised the state of BPDU guard functionality for this port. If BPDU guard functionality fot this port is disabled or guard functionality is enabled, but no BPDUs are received on this port, then hmIfaceStpBpduGuardStatus is set to false(2) for this port. If BPDU is received on an port with enabled BPDU guard functionality for this port (hmIfaceStpBpduGuardEnable=enable(1)) and globally (hmSysStpBPDUGuardEnable=enable(1)) then hmIfaceStpBpduGuardStatus is set to true(1) and additionally IfAdminStatus for this port is set to down(2). Variable hmIfaceStpBpduGuardStatus can be reset (to their original values (=false)) with switching BPDU guard functionality globally off. IfAdminStatus can be again reset to to their original values up() only manually.

OBJECT-TYPE

Capability of the interface coded as an integer value with each bit representing a special capability. Meaning of the bits: Bit 0: cabletest capability Bit 1: realtime capability according to IEEE 1588.

OBJECT-TYPE

The ingress limiter can work in different modes. Mode all limits the complete ingress traffic. Mode bc limits only the ingress broadcast traffic. Mode bc_mc limits the ingress broadcast and multicast traffic. Mode bc_mc_uuc limits the ingress broadcast, multicast and unknown unicast traffic. The limiter is hardware dependend. Not all modes are available on every hardware.

OBJECT-TYPE

The ingress limiter can measure the traffic on a bytes per second or on a packets per second basis. The limiter calculation mode is hardware dependend. Not all modes are available on every hardware.

OBJECT-TYPE

The rate of the ingress limiter. The value 0 disables the limiter.

OBJECT-TYPE

The egress limiter can work in different modes. Mode all limits the complete egress traffic. Mode bc limits only the egress broadcast traffic. Mode bc_mc limits the egress broadcast and multicast traffic. Mode bc_mc_uuc limits the egress broadcast, multicast and unknown unicast traffic. The limiter is hardware dependend. Not all modes are available on every hardware.

OBJECT-TYPE

The egress limiter can measure the traffic on a bytes per second or on a packets per second basis. The limiter calculation mode is hardware dependend. Not all modes are available on every hardware.

OBJECT-TYPE

The rate of the egress limiter. The value 0 disables the limiter.

OBJECT-TYPE

Surveys the interface utilization hmIfaceUtilization and generates an alarm for this interfaces, if the given limit is exceeded. A value of 0 disables the alarm generation.

OBJECT-TYPE

Surveys the interface utilization hmInfaceUtilization and removes the alarm condition for this interfaces, if the utilization value is below the given limit. A value of 0 disables the alarm removal.

OBJECT-TYPE

The alarm condition is given (true), if the given hmIfaceUtilizationAlarmUpperThreshold limit is exceeded by the interface utilization. The alarm condition will be removed, when the interface utilization falls below the hmIfaceUtilizationAlarmLowerThreshold.

OBJECT-TYPE

This variable configures the cable crossing on twisted pair cables. When set to 'enable', the port uses the crossover mode. When set to 'disable', the port does not use the crossover mode. 'Unsupported' is shown, if a port does not support cable crossing. It is not possible to set 'unsupported' to any type of port.

OBJECT-TYPE

This variable configures the PHY specific fast link detection feature on this port. 'Unsupported' is shown, if a port does not support this feature. It is not possible to set 'unsupported' to any type of port.

OBJECT-TYPE

This object is 'obsolete' and is replaced by hmIfaceExtAcceptableFrameTypes. When this is admitOnlyVlanTagged(2) the device will discard untagged frames received on this port. When admitOnlyUntagged(3), the device will discard any frames with a VLAN tag. When admitAll(1), all frames are accepted and untagged or Priority-Tagged frames received on this port will be assigned to the PVID for this port. This control does not affect VLAN independent BPDU frames, such as GVRP and STP. It does affect VLAN dependent BPDU frames, such as GMRP.

OBJECT-TYPE

This table contains variables for each trunk of the switch.

OBJECT-TYPE

The entry of the hmTrunkTable.

OBJECT-TYPE

Index to identify a link aggregation instance

OBJECT-TYPE

List of interfaces which are aggregated in the trunk. each octet pair contains the slotID and interfaceID. Interfaces are added or deleteted using the variable hmIfaceTrunkID.

OBJECT-TYPE

Textual description of the trunk

OBJECT-TYPE

action according to hmIfaceAction which is performed for all interfaces in the trunk

OBJECT-TYPE

The desired state of the trunk. if this variable is set to down(2), all interfaces which are aggregated in the trunk are switched off simultaneously. Reading this variable returns up(1) if at least one interface of the trunk is operational (up).

OBJECT-TYPE

The operational state of the trunk. Reading this variable returns up(1) if at least one interface of the trunk is operational (up).

OBJECT-TYPE

Time since system boot when there was a change in either the operational state of the trunk or the list of aggregated interfaces.

OBJECT-TYPE

This table contains variables for each SFP.

OBJECT-TYPE

Entry for a detected SFP.

OBJECT-TYPE

Index to identify a module. This value is never greater than hmSysGroupModuleCapacity.

OBJECT-TYPE

Index to identify an interface within a module. This value is never greater than hmSysModulePortCapacity.

OBJECT-TYPE

The SFP's Connector Type.

OBJECT-TYPE

The SFP's Transceiver type.

OBJECT-TYPE

The SFP's vendor IEEE company ID (OUI).

OBJECT-TYPE

The SFP's vendor name (ASCII).

OBJECT-TYPE

The SFP's part description number (ASCII).

OBJECT-TYPE

The SFP's part revision number (ASCII).

OBJECT-TYPE

The SFP's serial number provided by vendor (ASCII).

OBJECT-TYPE

The SFP's vendor manufacturing date code. Format is YY:MM:DD.

OBJECT-TYPE

The SFP's nominal bitrate in units of MBits/sec. Contains -1 in case of a device read error.

OBJECT-TYPE

This signed integer is used to identify the temperature within the SFP in units of centigrade (celsius). Contains -1000 in case of a device read error.

OBJECT-TYPE

The SFP's internally measured Tx Power in units of milliWatts. (ASCII representation of floating point number).

OBJECT-TYPE

The SFP's internally measured Rx Power in units of milliWatts. (ASCII representation of floating point number).

OBJECT-TYPE

The SFP's internally measured Tx Power in units of 1/10 microWatts.

OBJECT-TYPE

The SFP's internally measured Rx Power in units of 1/10 microWatts.

OBJECT-TYPE

The state of the SFP's internally measured Rx.

OBJECT-TYPE

Version of SFP's Hirschmann Information. Contains -1 in case of a device read error.

OBJECT-TYPE

Part Number of SFP's Hirschmann Information.

OBJECT-TYPE

Part Identifier of SFP's Hirschmann Information.

OBJECT-TYPE

1, if SFP contains vendor specific information by Hirschmann, otherwise 0.

OBJECT-TYPE

Indicates if the local agent supports this SFP.

OBJECT-TYPE

Max. usable length for the cable type '9/125 micrometer fiber' with this SFP in units of meters.

OBJECT-TYPE

Max. usable length for the cable type '50/125 micrometer fiber' with this SFP in units of meters.

OBJECT-TYPE

Max. usable length for the cable type '62.5/125 micrometer fiber' with this SFP in units of meters.

OBJECT-TYPE

Max. usable length for the cable type 'copper' with this SFP in units of meters.

OBJECT-TYPE

The SFP's internally measured Tx Power in units of dBm. (ASCII representation of floating point number).

OBJECT-TYPE

The SFP's internally measured Rx Power in units of dBm. (ASCII representation of floating point number).

OBJECT-TYPE

This displaystring represents the name of the Chassis. Any change of this variable will cause an automatically update of this value on each Basic Board in this Chassis.

OBJECT-TYPE

This variable controls the STP operation of the entire switch. To control the STP function of each port use hmIfaceStpEnable

OBJECT-TYPE

enables or disables flow control for the switch unit.

OBJECT-TYPE

Enable/Disable BOOTP operation. A (1) enables, a (2) disables. When disabled, no BOOTPs are transmitted by the system. When enabled, the system sends BOOTP requests at booting.

OBJECT-TYPE

Enable/Disable DHCP operation. A (1) enables, a (2) disables. When disabled, no DHCPs are transmitted by the system. When enabled, the system sends DHCP requests at booting.

OBJECT-TYPE

Enable/Disable Telnet operation. A (1) enables, a (2) disables. When disabled, no Telnet sessions are allowed by the system.

OBJECT-TYPE

Enable/Disable HTTP connection. A (1) enables, a (2) disables. When disabled, no HTTP is allowed by the system.

OBJECT-TYPE

Enable/Disable Plug&Play feature. A (1) enables, a (2) disables. if this variable is set to enable(1), special Plug&Play actions are performed at boot time and after a successful completion the value is automatically reset to the disable(2) state.

OBJECT-TYPE

Global configuration of feature broadcast limiter. If enabled, for each port the maximum rate of broadcasts can be specified.

OBJECT-TYPE

Time measured in seconds since 00:00:00 UTC, January 1, 1970. The clock of the agents may be set using this variable. Changing this variable on one agent automatically updates the value on the other agents in the same chassis.

OBJECT-TYPE

Shows the source of the system time.

OBJECT-TYPE

This variable controls the BPDU Guard operation of the entire switch (globally). To control the BPDU Guard function of each port use hmIfaceStpBpduGuardEnable. If BPDU guard functionality are global enabled (hmSysStpBPDUGuardEnable=enable(1)), and BPDU guard are enabled per port (hmIfaceStpBpduGuardEnable=enable(1)) and (R)STP are globally enabled and an BPDU are received on the port, then hmIfaceStpBpduGuardStatus is set to true(1) for this port and IfAdminStatus is set to down(2) for this port. Variable hmIfaceStpBpduGuardStatus can be reset (to their original values (=false)) with switching BPDU guard functionality globally off (hmSysStpBPDUGuardEnable=disable(2)). IfAdminStatus can be again reset to to their original values up() only manually. The default value of hmSysStpBPDUGuardEnable is disable(2).

OBJECT-TYPE

Advertised the reason why (R)STP could not be switched on. Error reasons are coded as OR operation bit by bit, see values: 0x00 - no errors - (R)STP is switched on, 0x01 - (R)STP cannot be switched on, because of standby mode, 0x02 - (R)STP cannot be switched on, because of kopp Local Active, 0x04 - (R)STP cannot be switched on, because of kopp Slave Active, 0x08 - (R)STP cannot be switched on, because of kopp Master Active, 0x10 - (R)STP cannot be switched on, because of sysRingOn and sysRMMode, 0x20 - (R)STP cannot be switched on, because of error if BB_SetParameter is occured.

OBJECT-TYPE

This variable shows the capability of the running software. The string is formated as follow: Byte 1 : Always L (for Layer) Byte 2 : 2 or 3 (dependend if the software supports onyl switching (2) or also routing (3)) Byte 3 : E or P (Enhanced or Professional software functionality)

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

Status from the PowerSupply LED.

OBJECT-TYPE

Status from the Standby LED.

OBJECT-TYPE

Status from the RM LED.

OBJECT-TYPE

Status from the Fault LED.

OBJECT-IDENTITY

OBJECT-TYPE

Status from the PowerSupply 1 LED.

OBJECT-TYPE

Status from the PowerSupply 2 LED.

OBJECT-TYPE

Status from the RM LED.

OBJECT-TYPE

Status from the Fault LED.

OBJECT-IDENTITY

OBJECT-TYPE

Status from the PowerSupply LED.

OBJECT-TYPE

Status from the Standby LED.

OBJECT-TYPE

Status from the RM LED.

OBJECT-TYPE

Status from the Fault LED.

OBJECT-TYPE

Status from the Relay1 LED.

OBJECT-TYPE

Status from the Relay2 LED.

OBJECT-IDENTITY

OBJECT-TYPE

Status from the PowerSupply LED.

OBJECT-TYPE

Status from the Standby LED.

OBJECT-TYPE

Status from the RM LED.

OBJECT-TYPE

Status from the Fault LED.

OBJECT-TYPE

Status from the Relay1 LED.

OBJECT-TYPE

Status from the Relay2 LED.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

Status from redundancy manager DIP switch.

OBJECT-TYPE

Status from Standby DIP switch.

OBJECT-IDENTITY

OBJECT-TYPE

Status from redundancy manager DIP switch.

OBJECT-TYPE

Status from ring ports DIP switch. on (1) indicates port 1 on module 1 and port 1 on module 2 are used as ring ports. off (2) indicates port 1 and 2 on module 1 are used as ring ports.

OBJECT-TYPE

Status from Standby DIP switch.

OBJECT-TYPE

Status from DIP switch configuration. on (1) indicates DIP switch configuration is enabled. off (2) indicates DIP switch configuration is disabled.

OBJECT-TYPE

Enable or Disable the DIP switch configuration. If set to disable DIP switches are ignored.

OBJECT-TYPE

TRUE if hmDIPSwitchAdminState is set to disable and hardware DIP switch setting is enabled.

OBJECT-TYPE

Maximum number of trunks for this chassis.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

The global ingress limiter can be enabled or disabled.

OBJECT-TYPE

The global ingress limiter can work in different modes. Mode all limits the complete ingress traffic. Mode bc limits only the ingress broadcast traffic. Mode bc_mc limits the ingress broadcast and multicast traffic. Mode bc_mc_uuc limits the ingress broadcast, multicast and unknown unicast traffic. The limiter is hardware dependend. Not all modes are available on every hardware.

OBJECT-IDENTITY

OBJECT-TYPE

The global unknown unicast ingress limiter can be enabled or disabled. The limiter is hardware dependend.

OBJECT-TYPE

The global unknown unicast ingress limiter can measure the traffic on a bytes per second or on a packets per second basis. The limiter calculation mode is hardware dependend. Not all modes are available on every hardware.

OBJECT-TYPE

The rate of the global unknown unicast ingress limiter. The value 0 disables the limiter.

OBJECT-IDENTITY

OBJECT-TYPE

The global egress limiter can be enabled or disabled.

OBJECT-IDENTITY

OBJECT-TYPE

Maximum number of USB ports in this chassis.

OBJECT-IDENTITY

OBJECT-TYPE

Controls address learning by the switch. When disabled the address database of the switch will not be updated with dynamic filtering entries. Static Filtering Entries and Group Registration Entries are not affected.

OBJECT-TYPE

The Maximum Receive Unit MRU that can be received by the switch.

OBJECT-TYPE

Controls if the fast link detection is enabled or not.

OBJECT-TYPE

Controls if detection of address relearns is enabled or not.

OBJECT-TYPE

The value of relearnd addresses to signal address relearn threshold exceeded.

OBJECT-TYPE

Controls if duplex mismatch detection is enabled or not.

OBJECT-TYPE

The number of FDB Full indications that the agent has detected since reboot.

OBJECT-TYPE

Mode to optimize the MAC address table hashing algorithm. Which modes can be configured is hardware dependend. After configuration a reboot is needed.

OBJECT-TYPE

Shows the current hash mode of this device.

OBJECT-IDENTITY

OBJECT-TYPE

Controls the VLAN learning mode by the switch. When set to IVL Independend VLAN Learning is active. When set to SVL Shared VLAN Learning is active. After setting this variable the switch have to be restarted.

OBJECT-TYPE

Shows the current VLAN learning mode. When set to IVL Independend VLAN Learning is active. When set to SVL Shared VLAN Learning is active.

OBJECT-IDENTITY

OBJECT-TYPE

Enables the service mode. If enabled, the switch can be separated into two switching areas with the redundant power supply. The two HIPER Ring ports are in area one. The other ports are in area two. Area one is VLAN capable, area two is not VLAN capable.

OBJECT-TYPE

Defined the Vlan for the service mode. The Vlan must be a valid Vlan and neither Vlan 0 (mgmt vlan) nor Vlan 1 (Default Vlan).

OBJECT-TYPE

If enabled, the switch has been separated into two switching areas with the redundant power supply. The two HIPER Ring ports are in area one. The other ports are in area two. Area one is VLAN capable, area two is not VLAN capable.

OBJECT-IDENTITY

OBJECT-TYPE

Rstp Mrp is enabled if this object is set to enable(1). Rstp Mrp is disabled if this object is set to disable(2).

OBJECT-TYPE

This object indicates a Rstp Mrp fail configuration if the value true is shown.

OBJECT-TYPE

The identifier of the device which has a Rstp Mrp fail configuration or Null if there is no fail configuration.

OBJECT-IDENTITY

OBJECT-TYPE

Controls RAM selftest on coldstart of the device. When disabled the device booting time is reduced.

OBJECT-TYPE

If enabled the software does make a reboot if there is a serious error detected.

OBJECT-TYPE

Status of the memory managment unit.

OBJECT-TYPE

If enabled the software does a reboot if there is a Half duplex mismatch error is detected. The option depends on hmSysSelftestRebootOnError.

OBJECT-TYPE

Enable or disable the System Monitor access during the boot phase. Please note: If the System Monitor is disabled, it is possible to lose access to the device permanently in case of loosing administrator password or misconfiguration.

OBJECT-IDENTITY

OBJECT-TYPE

Unique OEM ID.

OBJECT-TYPE

Maximum number of signal contacts for this chassis. Within each managed chassis/switch, the groups are uniquely numbered in the range from 1 to hmSysMaxSignalContacts.

OBJECT-TYPE

Enables/Disables HTTPS access to the device. A (1) enables, a (2) disables.

OBJECT-TYPE

The port number of the HTTPS web server.

OBJECT-TYPE

Enable/disable loading from ACA on startup.

OBJECT-TYPE

Admin State of service shell. (1=enable, 2=disable).

OBJECT-TYPE

Controls HTTPS certificate fingerprint generation. If set to 'sha1' hmSysHttpsCertFingerPrint will show the SHA1 fingerprint of the certificate.

OBJECT-TYPE

The HTTPS certificate fingerprint as hash. The type of the hash is defined with hmSysHttpsCertFingerPrintType.

OBJECT-TYPE

This table contains variables for each interface of the switch.

OBJECT-TYPE

The entry of the hmInterfaceExtTable.

OBJECT-TYPE

When this is admitOnlyVlanTagged(2) the device will discard untagged frames received on this port. When admitOnlyUntagged(3), the device will discard any frames with a VLAN tag. When admitAll(1), all frames are accepted and untagged or Priority-Tagged frames received on this port will be assigned to the PVID for this port. This control does not affect VLAN independent BPDU frames, such as GVRP and STP. It does affect VLAN dependent BPDU frames, such as GMRP.

OBJECT-TYPE

This table contains all variables related to the power supply units of the chassis/switch. For each power supply slot exists one instance.

OBJECT-TYPE

The entry of the hmPSTable.

OBJECT-TYPE

The value of SysID is assigned so as to uniquely identify a chassis/switch among the subordinate managed objects of the system.

OBJECT-TYPE

This Index is used to identify the associated power supply unit.

OBJECT-TYPE

Indicates the operational state of the associated power supply. If the value of this variable changes, a hmPowerSupply trap is sent.

OBJECT-TYPE

Type of the associated power supply.

OBJECT-TYPE

Version of the associated power supply.

OBJECT-TYPE

Description of the associated power supply.

OBJECT-TYPE

Serial number of the associated power supply.

OBJECT-TYPE

Product code of the associated power supply.

OBJECT-TYPE

Power budget of the associated power supply.

OBJECT-TYPE

This table contains all variables related to the fan units of the chassis/switch. For each fan slot exists one instance.

OBJECT-TYPE

The entry of the hmFanTable.

OBJECT-TYPE

The value of SysID is assigned so as to uniquely identify a chassis among the subordinate managed objects of the system.

OBJECT-TYPE

This Index is used to identify the associated fan.

OBJECT-TYPE

Indicates the operational state of the associated fan.

OBJECT-IDENTITY

OBJECT-TYPE

Global configuration of feature IP-TOS priority to 802.1D-1998 priority. If enabled, the priority of the TOS field is mapped to 802.1D priority

OBJECT-TYPE

Global configuration of feature priority by MAC address. If enabled, for each static MAC address a priority could be specified

OBJECT-TYPE

enables or disables the transparent mode for priority tagged frames (frames with VLAN-ID 0) for the switch unit.

OBJECT-TYPE

Table for assigning priority to MAC addresses

OBJECT-TYPE

The entry of the hmPrioMACAddressTable.

OBJECT-TYPE

same as dot1dStaticAddress

OBJECT-TYPE

to be compatible with dot1dStaticTable

OBJECT-TYPE

priority value for the frame with the specific destination MAC address. 0..7: priority 8 : disabled (no priority by MAC address) 9 : discard the frame

OBJECT-TYPE

status flag according to dot1dStaticStatus

OBJECT-TYPE

Translation table for traffic classes to 802.1D-1998 priority

OBJECT-TYPE

The entry of the hmPrioTrafficClassTable.

OBJECT-TYPE

This index is used to identify the associated traffic class

OBJECT-TYPE

With this parameter the queue mode of each traffic class can be set. 2..99: weight for WFQ (Weighted-Fair-Queuing) 100: strict priority

OBJECT-TYPE

Translation table IP-TOS priority to 802.1D-1998 priority

OBJECT-TYPE

The entry of the hmPrioTosToPrioEntry.

OBJECT-TYPE

This index is used to identify the associated TOS value

OBJECT-TYPE

This index is used to identify the associated 802.1D priority

OBJECT-TYPE

A table containing filtering information configured into the bridge by (local or network) management or dynamic by GMRP or IGMP Snooping specifying the set of ports to which frames received from specific ports and containing specific destination addresses are allowed to be forwarded. The value of zero in this table as the port number from which frames with a specific destination address are received, is used to specify all ports for which there is no specific entry in this table for that particular destination address. Entries are valid for unicast and for group/broadcast addresses.

OBJECT-TYPE

Filtering information configured into the bridge by (local or network) management specifying the set of ports to which frames received from a specific port and containing a specific destination address are allowed to be forwarded.

OBJECT-TYPE

The destination MAC address in a frame to which this entry's filtering information applies. This object can take the value of a unicast address, a group address or the broadcast address.

OBJECT-TYPE

Either the value '0', or the port number of the port from which a frame must be received in order for this entry's filtering information to apply. A value of zero indicates that this entry applies on all ports of the bridge for which there is no other applicable entry.

OBJECT-TYPE

The set of ports to which frames received from a specific port and destined for a specific MAC address, are allowed to be forwarded. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'. (Note that the setting of the bit corresponding to the port from which a frame is received is irrelevant.) The default value of this object is a string of ones of appropriate length.

OBJECT-TYPE

The complete set of ports, to which frames destined for this Group MAC Address are currently being forwarded. This includes Group MAC Addresses which were set statically or which were learnt by GMRP or some other dynamic mechanism. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'. (Note that the setting of the bit corresponding to the port from which a frame is received is irrelevant.) The default value of this object is a string of ones of appropriate length.

OBJECT-TYPE

This object indicates the status of this entry. The default value is permanent(3). other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object removes the corresponding entry. permanent(3) - this entry is currently in use and will remain so after the next reset of the bridge. deleteOnReset(4) - this entry is currently in use and will remain so until the next reset of the bridge. deleteOnTimeout(5) - this entry is currently in use and will remain so until it is aged out.

OBJECT-IDENTITY

OBJECT-TYPE

hmRS2OperMode shows the operational mode of the system: normal: normal mode, standby-active: standby mode, but switch is active, because the master switch is e.g. not reachable, standby-inactive: stand by mode, redundancy-manager-active: redundancy mode and redundancy-manager has closed RS2 ring, redundancy-manager-inactive: redundancy mode and redundancy-manager has opened RS2 ring. If the value changes, a trap is sent.

OBJECT-TYPE

RS2hmConfigError indicates a configuration error of the system: no error: no configuration error, error: in normal mode hmConfigError indicates failure of control line or connection of 2 RS2 in normal mode, in stand by mode hmConfigError indicates absence of control line, failure of control line or connection of 2 RS2 in stand by mode.

OBJECT-TYPE

hmRS2SigRelayState shows the state of the (non potential) signalling relay in standard mode: off: ok, on: powersupply not ok or linkstate of a port not ok or configuration error, see power supply table or ifMauTable (attribute ifMauMediaAvailable) or hmConfigError for details.

OBJECT-TYPE

This table contains all variables to mask an alarm for the signalling relay, produced by a link. The index for a link corresponds with ifMauIfIndex.

OBJECT-TYPE

The entry of the hmSigLinkTable.

OBJECT-TYPE

This index is used to identify the associated link and corresponds with ifMauIfIndex.

OBJECT-TYPE

Indicates whether an alarm for the signalling relay of the associated link will be produced or not, so you can mask the value of ifMauMediaAvailable.

OBJECT-TYPE

This object identifies the reason for a trap. There are three reasons for a trap: hmRS2ConfigError ifMauMediaAvailable hmPSState The entity which produces the trap, is specified by hmSigReasonIndex.

OBJECT-TYPE

This attribute specifies the entity which produces the trap. 1 - n: index of powersupply table / interfaces table 0: config-error.

OBJECT-IDENTITY

OBJECT-TYPE

This variable can be used to set manually the redundancy partner of the RS2 agent.

OBJECT-TYPE

This table describes the topology of rs2-rings.

OBJECT-TYPE

The entry of the hmRS2TopologyTable.

OBJECT-TYPE

This index is used to identify the associated link and corresponds with ifMauIfIndex.

OBJECT-TYPE

This variable can be used to set manually the next RS2 agent.

OBJECT-IDENTITY

OBJECT-TYPE

Set this variable to configure the status of the connection mirroring functionality. The definition of a destination port is not required.

OBJECT-TYPE

Set this variable to the first port to be mirrored.

OBJECT-TYPE

Set this variable to the second port to be mirrored.

OBJECT-IDENTITY

OBJECT-TYPE

When set to active the Learning Process is disabled, no new Dynamic Filtering Entries are created and exsisting Dynamic Filtering Entries are removed from the Filtering Database. Static Filtering Entries and Group Registration Entries are not affected.

OBJECT-IDENTITY

OBJECT-TYPE

When set to standard, this is the default, the signalling relay shows the state of hmRS2SigRelayState. When set to manual, the relay is controlled by hmRS2SigRelayManualState.

OBJECT-TYPE

When set to on, this is the default, the signalling relay is opened. When set to off the relay is closed.

OBJECT-IDENTITY

OBJECT-TYPE

Enables/disables the VLAN mode on this device. When enabled the switch will operate in 802.1Q mode, else in 802.1d mode. After setting this variable the switch have to be reset. The default value is disable.

OBJECT-TYPE

Shows the current VLAN mode of this device. When enabled the switch operates in 802.1Q mode, else in 802.1d mode.

OBJECT-IDENTITY

OBJECT-TYPE

Result of the selftest coded as an integer value with each bit representing the result of a different sub part test. Bits set in the result indicate error conditions of the sub part tests. Meaning of the bits: Bit 0: error switch memory

OBJECT-TYPE

Mode of the selftest coded as an integer value with each bit representing a special behaviour of the tests. Meaning of the bits: Bit 0: reboot on failure Bit 1: show failure with hmRS2SigRelayState (a trap will be send also) Bit 2: do switch memory test on start up Bit 3: Clear Bit 2 after next reboot if test has been successfully completed

OBJECT-IDENTITY

OBJECT-TYPE

Enables/disables an alarm for the signalling relay of the powersupply state.

OBJECT-IDENTITY

OBJECT-TYPE

When enabled the message 'redundancy not guaranteed' will be signalled on the signalling relay.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

This table describes private vlan enhancements of rs2-4r devices.

OBJECT-TYPE

The entry of the hmRS4RVlanPortTable.

OBJECT-TYPE

This index is used to identify the port.

OBJECT-TYPE

When enabled all tags are removed when sending packets on the port (egress). When disabled tag format is not changed, but RSTP frames are sent tagged. This variable is only used if RSTP is enabled. The default value is enable.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

Enables/disables the hash optimizing mode on this device. When enabled the switch will use another hash algorithm optimized for incrementing addresses. After setting this variable the switch have to be reset. The default value is disable.

OBJECT-TYPE

Shows the current hash mode of this device. When enabled the switch uses the optimized hash mode, else the normal mode.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

Result of the selftest coded as an integer value with each bit representing the result of a different sub part test. Bits 0..15 set in the result indicate warning conditions, bits 16..31 indicate error conditions of the sub part tests. Meaning of the bits: Bit 0: default configuration activated and running Bit 2: BB_DATAMEM_ERROR caused by log-entry: S_mmcssp_CRC_ERROR_DATAMEM ( in mmcNP5400Int() ) S_mmcssp_LEN_ERROR_DATAMEM ( in mmcNP5400Int() ) Bit 3: BB_PARITY_ERROR caused by log-entry: S_mmcssp_PER_ON_VIX_OR_IPC ( in mmcNP5400Int() ) S_mmcssp_PE_PIF_VIX_DATA ( in mmcEpifPintProc(), mmcGpifPintProc(), mmcXpifPintProc() ) S_mmcssp_PE_PIF_GGI ( in mmcGpifPintProc(), mmcXpifPintProc() ) Bit 4: BOOT_ERROR_PIF caused by log-entry: S_mmcssp_PIF_BOOT_ERROR ( in mmcEpifPintProc(), mmcGpifPintProc(), mmcXpifPintProc() ) Bit 5: MMC_PORT_PROBLEM caused by log-entry: S_mmcssp_WRONG_PORT_IN_MSG ( in mmcGotAliveMsg() ) S_mmcssp_NO_ADDRESS_FOR_PORT ( in mmcPortConfig() ) Bit 16: configuration data in bootblock of flash was invalid through startup Bit 17: configuration in flash is corrupted

OBJECT-TYPE

Result of the selftest coded as an integer value with each bit representing the result of a different sub part test. Bits set in the result indicate error conditions of the sub part tests. Meaning of the bits: Bit 0: selftest error of backplane port no 1 Bit 1: selftest error of backplane port no 2 Bit 2: selftest error of backplane port no 3 Bit 3: selftest error of backplane port no 4 Bit 8: selftest error of network processor no 1 Bit 9: selftest error of network processor no 2 Bit 10: selftest error of network processor no 3 Bit 11: selftest error of network processor no 4 Bit 12: selftest error of xpif no 1 Bit 13: selftest error of xpif no 2 Bit 14: selftest error of xpif no 3 Bit 15: selftest error of xpif no 4 Bit 16: error packet memory size Bit 30: error on board eeprom

OBJECT-TYPE

Result of the selftest coded as an integer value with each bit representing the result of a different sub part test. Bits set in the result indicate error conditions of the sub part tests. Meaning of the bits: Bit 0: communication error with card 1 Bit 1: communication error with card 2 Bit 2: communication error with card 3 Bit 3: communication error with card 4 Bit 4: communication error with card 5 Bit 24: main and redundant eeprom 2 are different Bit 25: main and redundant eeprom 1 are different Bit 27: error on redundant eeprom 2 Bit 28: error on redundant eeprom 1 Bit 29: error on main eeprom 2 Bit 30: error on main eeprom 1

OBJECT-TYPE

Result of the selftest coded as an integer value with each bit representing the result of a different sub part test. Bits set in the result indicate error conditions of the sub part tests. Meaning of the bits: Bit 0: selftest error of port no 1 Bit 1: selftest error of port no 2 Bit 2: selftest error of port no 3 Bit 3: selftest error of port no 4 Bit 4: selftest error of port no 5 Bit 5: selftest error of port no 6 Bit 6: selftest error of port no 7 Bit 7: selftest error of port no 8 Bit 16: selftest error of pif no 1 Bit 17: selftest error of pif no 2 Bit 30: error on module eeprom

OBJECT-TYPE

Result of the selftest coded as an integer value with each bit representing the result of a different sub part test. Bits set in the result indicate error conditions of the sub part tests. Meaning of the bits: Bit 0: selftest error of port no 1 Bit 1: selftest error of port no 2 Bit 2: selftest error of port no 3 Bit 3: selftest error of port no 4 Bit 4: selftest error of port no 5 Bit 5: selftest error of port no 6 Bit 6: selftest error of port no 7 Bit 7: selftest error of port no 8 Bit 16: selftest error of pif no 1 Bit 17: selftest error of pif no 2 Bit 30: error on module eeprom

OBJECT-TYPE

Result of the selftest coded as an integer value with each bit representing the result of a different sub part test. Bits set in the result indicate error conditions of the sub part tests. Meaning of the bits: Bit 0: selftest error of port no 1 Bit 1: selftest error of port no 2 Bit 2: selftest error of port no 3 Bit 3: selftest error of port no 4 Bit 4: selftest error of port no 5 Bit 5: selftest error of port no 6 Bit 6: selftest error of port no 7 Bit 7: selftest error of port no 8 Bit 16: selftest error of pif no 1 Bit 17: selftest error of pif no 2 Bit 30: error on module eeprom

OBJECT-TYPE

Result of the selftest coded as an integer value with each bit representing the result of a different sub part test. Bits set in the result indicate error conditions of the sub part tests. Meaning of the bits: Bit 0: selftest error of port no 1 Bit 1: selftest error of port no 2 Bit 2: selftest error of port no 3 Bit 3: selftest error of port no 4 Bit 4: selftest error of port no 5 Bit 5: selftest error of port no 6 Bit 6: selftest error of port no 7 Bit 7: selftest error of port no 8 Bit 16: selftest error of pif no 1 Bit 17: selftest error of pif no 2 Bit 30: error on module eeprom

OBJECT-TYPE

Setting this variable to enable(1) results in a full report of all detected selftest errors. The default value is disable(2).

OBJECT-TYPE

this variable indicates which management bus is selected.

OBJECT-IDENTITY

OBJECT-TYPE

Serial Number of the CPU board.

OBJECT-TYPE

Serial Number of the basic board.

OBJECT-TYPE

Serial Number of the packplane unit.

OBJECT-TYPE

Serial Number of module 1.

OBJECT-TYPE

Serial Number of module 2.

OBJECT-TYPE

Serial Number of module 3.

OBJECT-TYPE

Serial Number of module 4.

OBJECT-IDENTITY

OBJECT-TYPE

state of the configuration retrieval from a neighbour card

OBJECT-IDENTITY

OBJECT-TYPE

state of the user group configuration

OBJECT-IDENTITY

OBJECT-TYPE

This table contains all AUI variables that are module dependend.

OBJECT-TYPE

The entry of the hmAUIModuleTable.

OBJECT-TYPE

This index is used to identify a specific module.

OBJECT-TYPE

This variable shows the DTE Power Monitor DIP switch setting on the AUI module.

OBJECT-TYPE

This table contains all AUI variables that are port dependend.

OBJECT-TYPE

The entry of the hmAUIPortTable.

OBJECT-TYPE

This index is used to identify a specific port.

OBJECT-TYPE

This variable shows the DTE Power value of the AUI port.

OBJECT-TYPE

This variable shows the SQE Test DIP switch setting on the AUI port.

OBJECT-IDENTITY

OBJECT-IDENTITY

The events of hmAgent.

OBJECT-TYPE

This object, when read, always returns a value of other(1). A value of reset(2) has the same effect as a power-on sequence (coldstart). Writing a value of hotRestart(10) leads to a warmstart. When set to resetStats(3), a reset of all statistic counters within the whole switch will be forced. A value of resetFDB(4) will clear the forwarding database. If set to resetARP(5), the ARP table will be flushed. The value gbl-reset(12) will result in a reset of the whole chassis. Any other value results in a badValue status code.

OBJECT-TYPE

Result of the last activated action. A value of zero indicates that the result is ok. Bits set in the result indicate error conditions.

OBJECT-IDENTITY

OBJECT-TYPE

IP address of the management agent board. Changing this value will take effect after activating with hmNetAction.

OBJECT-TYPE

Physical base address (MAC-address) of the agent.

OBJECT-TYPE

IP address of the default gateway. Changing this value will take effect after activating with hmNetAction.

OBJECT-TYPE

Subnet mask. Changing this value will take effect after activating with hmNetAction.

OBJECT-TYPE

Base address of the IP address range used by the point-to-point protocol. The IP addresses hmNetPPPBaseAddress..hmNetPPPBaseAddress+4 are assigned to the client machines attached to management agents 1..5. The management agents can be reached using addresses hmNetPPPBaseAddress+10..hmNetPPPBaseAddress+14. Changing this variable on one agent automatically updates the value on the other agents in the same chassis.

OBJECT-TYPE

Subnet mask used by the point-to-point protocol. Changing this variable on one agent automatically updates the value on the other agents in the same chassis.

OBJECT-TYPE

This object, when read, always returns a value of other(1). Setting the object to activate(2) causes a reconfiguration of the IP protocol stack with the current values of hmNetLocalIPAddr, hmNetGatewayIPAddr and hmNetMask.

OBJECT-TYPE

Vlan ID of the IP protocol stack. If the value is 0, Traffic from all Vlans is accepted. Every other value means that only traffic of the appropriate Vlan is accepted and outgoing traffic uses this Vlan ID.

OBJECT-TYPE

The number of MAC addresses reserved for this device, starting from hmNetLocalPhysAddr.

OBJECT-TYPE

Vlan Priority which is used in management replies.

OBJECT-TYPE

IP DSCP value which is used in management replies.

OBJECT-IDENTITY

OBJECT-TYPE

Sets the mode of the ip address conflict detection mechanism on this device. enable(1): Both active and passive detection are active. disable(2): No detection takes place. activeDetectionOnly(3): During configuration of a local ip address the device actively probes the network for this ip address. passiveDetectionOnly(4): The device listens passively on the network if another device with an already locally configured ip address appears. In this case the own ip address is actively defended by transmitting gratituous arp's.

OBJECT-TYPE

If enabled, the device sends periodic arp probes.

OBJECT-TYPE

The maximum detection delay time in milliseconds. Time gap between arp probes.

OBJECT-TYPE

Delay in seconds to the next arp probe cycle after an ip address conflict was detected.

OBJECT-TYPE

Maximum number of frequent address protections.

OBJECT-TYPE

Delay in milliseconds between two protections.

OBJECT-TYPE

true(1) if an active address conflict is detected. false(2) if no present address conflict.

OBJECT-TYPE

This table contains address conflict detection information on the local system known to this agent.

OBJECT-TYPE

IP Address conflict detection information about a particular address on the local system kown to this agent. There may be multiple addresses configured on the system. Entries may be created and deleted in this table by the agent.

OBJECT-TYPE

A TimeFilter for this entry. See the TimeFilter textual convention in IETF RFC 2021 and http://www.ietf.org/IESG/Implementations/RFC2021-Implementation.txt to see how TimeFilter works.

OBJECT-TYPE

The type of management address identifier encoding used in the associated 'hmNetACDAddr' object.

OBJECT-TYPE

The string value used to identify the management address component associated with the local system.

OBJECT-TYPE

The physical address of the device that was detected causing the ip address conflict.

OBJECT-TYPE

The integer value used to identify the interface number on the local system where the ip address conflict was detected.

OBJECT-IDENTITY

OBJECT-TYPE

Sets the status of the MAC address conflict detection mechanism on this device.

OBJECT-TYPE

MAC address in case of a conflict.

OBJECT-IDENTITY

OBJECT-TYPE

Enables/disables the HiDiscovery protocol on this device. This protocol allows a remote host to detect devices without an ip configuration. It also allows the host to set ip parameters, like the ip address, the netmask and the gateway address. If only detection and no configuration is allowed set this object to readOnly(3).

OBJECT-TYPE

Relay/bridge HiDiscovery frames.

OBJECT-TYPE

Shows the HiDiscovery protocols supported by the device.

OBJECT-IDENTITY

OBJECT-TYPE

Enables/disables the Simple Network Time Protocol on this device.

OBJECT-TYPE

The IP Address of an external Time Server.

OBJECT-TYPE

The time in seconds since 01/01/1900 UTC.

OBJECT-TYPE

The difference between local time and UTC in minutes.

OBJECT-TYPE

IP address of a secondary (backup) time server.

OBJECT-TYPE

SNTP synchronisation interval in seconds.

OBJECT-TYPE

This MIB variable specifies whether SNTP broadcasts will be allowed to synchronize the local clock. If hmNetSNTPStatus is enabled, this variable will be ignored and broadcasts will not set the local clock.

OBJECT-TYPE

Destination address for SNTP broadcasts. A broadcast, multicast or unicast address may be specified. Setting the address to 0.0.0.0 disables SNTP broadcasts.

OBJECT-TYPE

Vlan for anycast mode.

OBJECT-TYPE

Interval of SNTP broadcast messages in seconds.

OBJECT-TYPE

Operational status of the SNTP sub-system. The value is a bit mask: 0 SNTP disabled 1 local system clock synchronized 2 SNTP loop detected 4 generic error 8 once synced, client disabled 100 server 1 not synchronized 200 server 1 bad protocol version 400 server 1 not responding 10000 server 2 not synchronized 20000 server 2 bad protocol version 40000 server 2 not responding (Note that all values are hexadecimal.)

OBJECT-TYPE

The threshold in milli-seconds whether to decide to set the received SNTP time directly to the local clock or not. If the hmNetSNTPTimeAdjustThreshold value is 0, the received SNTP time will be set directly to the local clock every time a SNTP message is received. If the difference between the local clock time and the received SNTP time is fewer than the hmNetSNTPTimeAdjustThreshold value, the local clock will not be set. If the difference between the local clock time and the received SNTP time is equal or larger than the hmNetSNTPTimeAdjustThreshold value, the local clock will be set. Value must be in the <0-2000> milliseconds interval.

OBJECT-TYPE

If enabled, SNTP ist automaticaly disabled after once synchronized to an SNTP Server.

OBJECT-TYPE

The SNTP server is enabled only if synchronized to another external time reference. (e.g. SNTP or PTP)

OBJECT-TYPE

Enables/disables the SNTP server on this device if hmNetSNTPStatus is enabled.

OBJECT-TYPE

Enables/disables the SNTP client on this device if hmNetSNTPStatus is enabled.

OBJECT-IDENTITY

OBJECT-TYPE

Selects operation mode for NTP.

OBJECT-TYPE

Address type for server 1. Currently, only ipv4 is supported.

OBJECT-TYPE

The address of the first external time server.

OBJECT-TYPE

Address type for server 2. Currently, only ipv4 is supported.

OBJECT-TYPE

The address of the second external time server.

OBJECT-TYPE

NTP synchronisation interval in seconds. NTP will round down the value to a power of 2. The protocol will use an interval between the rounded value and the next power of 2.

OBJECT-TYPE

Address type for anycasts. Currently, only ipv4 is supported.

OBJECT-TYPE

Destination address for NTP broadcasts. A broadcast, multicast or unicast address may be specified. Setting the address to 0.0.0.0 disables NTP broadcasts.

OBJECT-TYPE

Interval of NTP broadcast messages in seconds. NTP will round down the value to a power of 2.

OBJECT-TYPE

Operational status of the NTP sub-system.

OBJECT-TYPE

Operational status of the NTP sub-system. The value is a bit mask: 1 local system clock synchronized 2 generic error (see hmNetNTPStatusText) 100 server 1 not synchronized 200 server 1 protocol error 400 server 1 not responding 800 server 1 synchronization in progress 10000 server 2 not synchronized 20000 server 2 protocol error 40000 server 2 not responding 80000 server 2 synchronization in progress (Note that all values are hexadecimal.)

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

Enable or disable the Precision Time Protocol on this node.

OBJECT-TYPE

Initialize the PTP Clock. Value 2: The specification initialization set shall be used. Value 3: The initialization set stored in nonvolatile storage for recovery after a power fail shall be used. Value 1: no action. In GET operations the variable always returns other(1)

OBJECT-TYPE

This members value shall indicate which clock mode is used. The ptp-mode-boundary-clock mode specifies the mode as described in the IEEE1588 standard. In the 'ptp-mode-simple-ptp' mode the device only accepts PTP sync messages, sets the time directly and no BMC algorithm will run. If the clock mode is changed, PTP will be initialized.

OBJECT-TYPE

This members value shall indicate the slave port where this clock is synchronized in the ptp-mode-static-boundary-clock mode. The default value is 0 (i.e. clock is grandmaster).

OBJECT-TYPE

If the clock is synchronized to the current Master this object is set to true. Otherwise it is set to false. The clock sets this object to true, if the offset (ns) to the current Master is less than hmNetPTPSyncLowerBound. The clock sets this object to false, if the offset (ns) to the current Master is bigger than hmNetPTPSyncUpperBound.

OBJECT-TYPE

This object defines when the hmNetPTPIsSynchronized object is set to true. If the absolute value of the offset is smaller than hmNetPTPSyncLowerBound, the hmNetPTPIsSynchronized is set true. The value is interpreted as nanoseconds.

OBJECT-TYPE

This object defines when the hmNetPTPIsSynchronized object is set to false. If the absolute value of the offset is bigger than hmNetPTPSyncUpperBound, the hmNetPTPIsSynchronized is set false. The value is interpreted as nanoseconds.

OBJECT-TYPE

The clock stratum, or stratum number, describes one measure of the quality of a clock. Each clock shall be characterized by a stratum number to be used by the best master clock algorithm as one parameter of clock quality. A clock stratum of 1 is the best, where the default clock stratum is 255.

OBJECT-TYPE

The clock identifier indicates the nature and expected absolute accuracy and epoch of a given clock. Possible values are ATOM, GPS, NTP, HAND, INIT, DFLT. Values with less characters than the maximum allowed length will be padded with zero characters.

OBJECT-TYPE

The clock variance reflects the inherent characteristics of the clock. It is an estimate of the local clock from a linear time scale when it is not synchronized to another PTP clock using the PTP protocol.

OBJECT-TYPE

A clock may be administratively designated as part of a preferred master clock set. This creates a set of clocks that will be favored over those not so designated in the selection of master clocks within a subdomain. The purpose of this designation is to allow users to specify a clock that will remain master in the presence of disconnection or connection of other clocks.

OBJECT-TYPE

The sync interval shall be the interval in seconds between successive Sync messages issued by master clocks. It shall have the same value for all clocks in a subdomain. The value of sync interval is a compromise between the inherent stability of the clocks, the responsiveness of the clocks in a subdomain to change, and the communication load imposed by PTP. Allowed values are 1,2,8,16 and 64. Changes are applied after the initialization with the init key init-with-nvm or after reboot if the configuration was saved.

OBJECT-TYPE

Each subdomain shall be characterized by a name recognized by all PTP clocks in the subdomain as the basis for sending and receiving PTP communications. Changes are applied after the initialization with the init key init-with-nvm or afer reboot if the configuration was saved.

OBJECT-TYPE

Current offset between its parent and this node in nanoseconds. Values greater than 1 second or less than -1 second are indicated by the maximum or minimum INTEGER values.

OBJECT-TYPE

This members value shall indicate the absolute value for the maximum offset between its parent and this node. The value is set to zero if the offset is the first time smaller than hmNetPTPSyncLowerBound. Offsets bigger than +/-1 second is indicated by the maximum value

OBJECT-TYPE

Current one_way_delay between its parent and this node in nanoseconds. Values greater than 1 second or less than -1 second are indicated by the maximum or minimum INTEGER values.

OBJECT-TYPE

This members value shall indicate PTP time in seconds since 1.1.1970.

OBJECT-TYPE

Relative rate (frequency or drift) between its parent and this node in nanoseconds. Values greater than 1 second or less than -1 second are indicated by the maximum or minimum INTEGER values.

OBJECT-TYPE

A digital PI servo has the following difference equation y(k) = y(k-1) + (Kp + Ki* T )* x(k) + Kp * x(k-1). This object specifies the Ki* 100000 term (integral part). Kp is 0.5. The default value of this object is 6250 that is Ki=1/16.

OBJECT-TYPE

The UUID of its Parent. For Ethernet this is the MAC address of the management agent.

OBJECT-TYPE

The UUID of its Grandmaster. For Ethernet this is the MAC address of the management agent.

OBJECT-TYPE

UTC time differs from the TAI time by a constant offset. This offset is modified on occasion by adding or subtracting leap seconds. The current number of leap seconds is represented in PTP by the value of hmNetPTPCurrentUTCOffset.

OBJECT-TYPE

When TRUE the last minute of the current day will contain 59 seconds.

OBJECT-TYPE

When TRUE the last minute of the current day will contain 61 seconds.

OBJECT-TYPE

This members value shall be the number of communication paths traversed between the local clock and the grandmaster clock. For example, steps_removed in a slave clock on the same PTP communication path as the grandmaster clock will have a value of 1, indicating that a single path was traversed.

OBJECT-TYPE

The PTP epoch began at 0 hours on 1 January 1970. Times measured since this epoch are designated in this standard as PTP Seconds. When the epoch is the PTP epoch, the value of the epoch number shall be the current number of times the 32-bit seconds clock has rolled over since the PTP epoch.

OBJECT-TYPE

Relative rate (frequency or drift) between a reference clock and this node in nanoseconds per second (ns/s). This value is only applied if no port is in slave state.

OBJECT-TYPE

This table contains variables for each PTP port of the switch.

OBJECT-TYPE

Entry for one port.

OBJECT-TYPE

Index to identify a port of the switch unit. This value is never greater than hmSysGroupCapacity.

OBJECT-TYPE

State of the PTP port intance.

OBJECT-TYPE

Controls the burst enable flag.

OBJECT-TYPE

The respective PTP Port of the Boundary Clock can be set to true (enabled) or set to false (disabled). If the port is disabled no PTP packets will be processed for the respective port.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

This table contains variables for each PTP2 port of the switch.

OBJECT-TYPE

Entry for one port.

OBJECT-TYPE

OBJECT-TYPE

State of the PTP2 port intance.

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

This object shows the capability of the ptp port.

OBJECT-TYPE

VLAN in which PTP packets are send. With a value of -1 all packets are send untagged

OBJECT-TYPE

VLAN priority of tagged ptp packets

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

Enable synchronisation of the local clock. This is only valid if syntonization is enabled

OBJECT-TYPE

VLAN in which PTP packets are send. With a value of -1 all packets are send untagged

OBJECT-TYPE

VLAN priority of tagged ptp packets

OBJECT-TYPE

Configures PTP parameters to a specific profile. Setting the object to user-defined (1) has no effect.

OBJECT-TYPE

If set to true only Announce messages including the TLVs specified in the Power Profile (C37.238) are accepted for syntonization

OBJECT-TYPE

This table contains variables for each PTP2 TC port of the switch.

OBJECT-TYPE

Entry for one port.

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-IDENTITY

OBJECT-TYPE

Enables/disables the SNMP Version 1 protocol.

OBJECT-TYPE

Enables/disables the SNMP Version 2 protocol.

OBJECT-TYPE

Enables/disables the SNMP Version 3 protocol.

OBJECT-TYPE

Enables/disables the SNMP protocol access on this device. If only read access is allowed set this object to readOnly(3).

OBJECT-TYPE

Enables/disables the synchronization between the SNMPv1 community and the SNMPv3 password. If enabled the first read-write community in hmAuthCommTable is used for the SNMPv3 admin password. This is the same password that is used in the user- and webinterface. Further, if enabled the first read-only community in hmAuthCommTable is used for the SNMPv3 user password.

OBJECT-TYPE

The port number of the snmp server. To activate the port number the device has to be restarted.

OBJECT-TYPE

Enables/disables authentication of SNMPv3 users via RADIUS server

OBJECT-TYPE

Enables/disables the SNMPv3 admin Data Encryption.

OBJECT-TYPE

Enables/disables the SNMPv3 user Data Encryption.

OBJECT-TYPE

Enables/disables the synchronization between the SNMPv3 password table (hmAgentUserConfigTable) and the SNMPv1/v2 community table (hmAgentSnmpCommunityConfigTable).

OBJECT-IDENTITY

OBJECT-TYPE

Indicates if a GPS module is available.

OBJECT-TYPE

Indicates if the GPS module is synchronized to the GPS signal.

OBJECT-TYPE

Shows the mode of the GPS module. If hmNetGPSMode is gpsIn(1), the GPS module reads the signal from a GPS receiver in the format given in hmNetGPSTimeStringFormat. If the mode is gpsOut(2), the GPS module sends out a signal in the format given in hmNetGPSTimeStringFormat.

OBJECT-TYPE

These are the GPS time string formats which a GPS module can read or write.

OBJECT-IDENTITY

OBJECT-TYPE

Enables/disables Management Access globally

OBJECT-TYPE

A list of Management Access Entries (Rules) to increase security

OBJECT-TYPE

An entry contains a rule for the Management Access.

OBJECT-TYPE

The unique index used for each row in the RMA Table

OBJECT-TYPE

Describes the status of a row in this table if it is active or not available ...

OBJECT-TYPE

Allowed IP address

OBJECT-TYPE

Network Mask

OBJECT-TYPE

Enables/disables HTTP access

OBJECT-TYPE

Enables/disbales SNMP access

OBJECT-TYPE

Enables/disables Telnet access

OBJECT-TYPE

Enables/disables SSH access

OBJECT-TYPE

Enables/disables HTTPS access

OBJECT-IDENTITY

OBJECT-TYPE

Full specified filename of the update file e.g. tftp://192.9.200.1/upd/bootrom.v3 .

OBJECT-TYPE

Full specified name of the configuration file e.g. tftp://192.9.200.1/cfg/config1.sav .

OBJECT-TYPE

Local or full specified url of the log file. If value is local, the log will be written to the flash. e.g. tftp://192.9.200.1/log/log300599.log or local.

OBJECT-TYPE

login name for the used file transport protocol.

OBJECT-TYPE

password for the used file transport protocol.

OBJECT-TYPE

This object, when read, always returns a value of other (1). When set to update (2), the updatefile specified by hmFSUpdFileName will be loaded. config-load (3) will load the configuration stored in the local flash. config-save (4) will write the present configuration to the flash. config-load-remote (5) will load the configuration stored in a file specified by hmFSConfigFileName (which may be in binary or script format). config-save-remote (6) will save the present configuration in a file specified by hmFSConfigFileName. log-save (7) will save the local logfile to a file specified with hmFSLogFileName. config-load-default (8) will restore the default settings and set-to-factory (9) will apply the factory settings to the system and save the configuration to flash. log-clear (10) will clear the logfile of the agent. gbl-update (12) will perform a software update of the whole chassis. config-load-backup (13) loads an automatically saved backup configuration config-remote-and-save (15) loads a configuration via tftp and saves it to the flash. toggleImage (20) switches between main and backup software image to be active (so it will be loaded after the next coldstart). config-save-remote-script (21) saves the current configuration in script format to the file specified by hmFSConfigFileName. Any other value results in a badValue status code.

OBJECT-TYPE

Result of the last activated action.

OBJECT-TYPE

By setting this MIB variable the user can control which configuration should be read during system initialization: default(1) : boot with factory settings local(2) : boot with locally stored configuration

OBJECT-TYPE

By setting this MIB variable the user can control which configuration should be read after switch initialization: boot(1) : the one which is selected by hmFSBootConfiguration local(2) : boot with locally stored configuration remote(3) : use the remotely stored configuration according to hmFSConfFileName

OBJECT-TYPE

error message of the last hmFSAction performed. If there was no error encountered, the value of this variable will be 'OK'

OBJECT-TYPE

Status of the local configuration. ok(1): Local and running configuration match. notInSync(2): Local and running configuration don't match, configuration has not yet been saved.

OBJECT-TYPE

Signature of the stored configuration. The signature changes each time the configuration is saved.

OBJECT-TYPE

a directory of the internal file system

OBJECT-TYPE

The entry of the hmFSFileTable.

OBJECT-TYPE

This index is used to identify the associated file

OBJECT-TYPE

file name excluding path

OBJECT-TYPE

file size in bytes

OBJECT-TYPE

date in UNIX format (seconds since 1 jan 1970)

OBJECT-IDENTITY

OBJECT-TYPE

Status of the AutoConfiguration Adapter. notPresent(1): AutoConfiguration Adapter has not been detected. removed(2): Configuration was loaded from adapter, but adapter was removed in running mode of the agent. ok(3): Configuration of adapter and switch match. notInSync(4): Configuration of adapter and switch don't match, e.g. configuration has not yet been written into the adapter. outOfMemory(5): Configuration is too large for the adapter. wrongMachine(6): Adapter contains configuration which cannot be loaded into this machine because it was created by a different type of switch. checksumErr(7): Data in adapter fails consistency check. genericErr(8): Any other failure, e.g. hardware malfunction. autodisabled(9): USB port has been disabled for safety reasons.

OBJECT-TYPE

The serial number provided by vendor (ASCII).

OBJECT-IDENTITY

OBJECT-TYPE

Administrative status of the configuration watchdog. enable(1): start/trigger the watchdog timer disable(2): turn off the watchdog This feature provides recovery from situations where the switch cannot be reached by the management station anymore. Whenever this variable is set to enable(1), the value of hmConfigWatchdogTimeInterval is loaded into the watchdog timer. This timer must be triggered before hmConfigWatchdogTimerValue reaches 0. If the watchdog timer expires, the last saved configuration of the switch will be restored. The watchdog is triggered with MIB read and write accesses

OBJECT-TYPE

Operational status of the configuration watchdog. enable(1): watchdog up and running disable(2): watchdog inactive

OBJECT-TYPE

Period of the watchdog timer in seconds.

OBJECT-TYPE

Current count-down value of the watchdog timer in seconds.

OBJECT-TYPE

Current IP Adress of station that triggers the watchdog.

OBJECT-IDENTITY

OBJECT-TYPE

This signed integer is used to identify the temperature within the agent in units of centigrade (celsius).

OBJECT-TYPE

This value is used to define a maximum level for the temperature within an agent. If the temperature rises above this upper limit, the management station will be notified by a hmTemperature trap.

OBJECT-TYPE

This value is used to define a minimum level for the temperature within a concentrator. If the temperature falls below this lower limit, the management station will be notified by a hmTemperature trap.

OBJECT-TYPE

A list of the neighbour agents in a chassis

OBJECT-TYPE

The entry of the hmNeighbourAgentTable.

OBJECT-TYPE

An index that uniquely identifies an agent by the slot in the chassis.

OBJECT-TYPE

The IP Address of the agent.

OBJECT-IDENTITY

OBJECT-TYPE

The maximum possible number of entries in the hmAuthHostTable. This value equates to the total number of trusted Hosts which potentially may be recognized.

OBJECT-TYPE

The maximum possible number of entries in the hmAuthCommTable. This value equates to the total number of communities which ly may be recognized.

OBJECT-TYPE

A list of valid SNMP Community Entries.

OBJECT-TYPE

A list of SNMP Community properties.

OBJECT-TYPE

An index that uniquely identifies an ordered entry in the SNMP Community Table.

OBJECT-TYPE

The name of this SNMP Community Entry, e.g. public. This object can only be written.

OBJECT-TYPE

The Read/Write (GET/SET) permission for the community. A (1) indicates perm-ro (GET) permission. A (2) indicates perm-wr (GET/SET) permission.

OBJECT-TYPE

The state of this community entry. Enable (1) defines an entry that is valid. Disable (2) defines an entry that is valid but not enabled. Delete (3) removes an entry from the table. Invalid (4) defines an entry that is no longer valid (e.g., an entry that was deleted) and should be ignored. An attempt to set a value of invalid (4) causes the agent to return SNMP_BADVALUE.

OBJECT-TYPE

A list of valid SNMP Trusted Host Entries.

OBJECT-TYPE

A list of SNMP Host properties.

OBJECT-TYPE

An index that uniquely identifies an ordered entry in the SNMP Trusted Host Table.

OBJECT-TYPE

The name of this SNMP Trusted Host Entry, e.g. host1.

OBJECT-TYPE

The index of this SNMP Trusted Host Entry's community entry in the hmAuthCommTable.

OBJECT-TYPE

The IP Address for the host. This identified host has permission to access information in this device's MIB tables, providing the SNMP security toggle is on (see hmMiscSNMPSecurity).

OBJECT-TYPE

The Network Mask for the trusted Host entry.

OBJECT-TYPE

The state of this trusted host entry. Enable (1) defines an entry that is valid. Disable (2) defines an entry that is valid but not enabled. Delete (3) removes an entry from the table. Invalid (4) defines an entry that is no longer valid (e.g., an entry that was deleted) and should be ignored. An attempt to set a value of invalid (4) causes the agent to return SNMP_BADVALUE.

OBJECT-IDENTITY

OBJECT-TYPE

The total number of entries in the hmTrapCommTable. This value equates to the total number of communities which potentially can be recognized.

OBJECT-TYPE

The total number of entries in the hmTrapDestTable. This equates to the total number of hosts which can potentially be sent SNMP traps.

OBJECT-TYPE

A list of valid SNMP Community Entries used for Traps.

OBJECT-TYPE

A list of SNMP Trap Community properties.

OBJECT-TYPE

An index that uniquely identifies an ordered entry in the SNMP Community Trap Table.

OBJECT-TYPE

The communities entry index of this SNMP Trap Community Entry.

OBJECT-TYPE

Enable (1) or Disable (2) the SNMP ColdStart Trap for this SNMP community.

OBJECT-TYPE

Enable (1) or Disable (2) the SNMP Link Down traps for this SNMP community.

OBJECT-TYPE

Enable (1) or Disable (2) the SNMP Link Up traps for this SNMP community.

OBJECT-TYPE

Enable (1) or Disable (2) the SNMP Authentication traps for this SNMP community.

OBJECT-TYPE

Enable (1) or Disable (2) the SNMP Bridge MIB traps for this SNMP community. Available Traps: newRoot (MACH) topologyChange (MACH)

OBJECT-TYPE

Enable (1) or Disable (2) the SNMP RMON traps for this SNMP community. Available Traps: risingAlarm (MACH, MICE, RS2) fallingAlarm (MACH, MICE, RS2)

OBJECT-TYPE

Enable (1) or Disable (2) the SNMP Enterprise usergroup traps for this SNMP community. Available Traps: hmNewUserTrap (MACH) hmPortSecurityTrap (MACH, MICE, RS2) hmPortSecConfigErrorTrap (MACH)

OBJECT-TYPE

Enable (1) or Disable (2) the SNMP Enterprise dual homing traps for this SNMP community. Available Traps: hmDuHmReconfig (MACH) hmDuHmRedundancy (MACH) hmRingRedReconfig (MACH, MICE)

OBJECT-TYPE

Enable (1) or Disable (2) the SNMP Enterprise chassis traps for this SNMP community. Available Traps: hmGroupMapChange (MACH) hmPowerSupply (MACH, MICE, RS2) hmFan (MACH) hmSignallingRelay (MICE, RS2) hmStandby (MACH, MICE, RS2) hmSelfTestError (MACH) hmModuleMapChange (MICE) hmTemperature (MACH) hmLoginTrap (MACH) hmDuplicateStaticAddressTrap (MACH)

OBJECT-TYPE

The state of this community entry. Enable (1) defines an entry that is valid. Disable (2) defines an entry that is valid but not enabled. Delete (3) removes an entry from the table. Invalid (4) defines an entry that is no longer valid (e.g., an entry that was deleted) and should be ignored. An attempt to set a value of invalid (4) causes the agent to return SNMP_BADVALUE.

OBJECT-TYPE

A list of valid SNMP Trap Trusted Host Destination entries.

OBJECT-TYPE

A list of SNMP Trap Trusted Host Destination properties.

OBJECT-TYPE

An index that uniquely identifies an ordered entry in the SNMP Trusted Host Destination Table.

OBJECT-TYPE

The name of this SNMP Trusted Host Destination Entry, e.g. Admin.

OBJECT-TYPE

The communities entry index of this SNMP Trusted Host Destination Entry's community.

OBJECT-TYPE

The IP Address for the host. This identified host has permission to access information in this device's MIB tables, providing the SNMP security toggle is on (see hmMiscSNMPSecurity).

OBJECT-TYPE

The Network Mask for the trusted Host Destination entry.

OBJECT-TYPE

The state of this trusted trap destination entry. Enable (1) defines an entry that is valid. Disable (2) defines an entry that is valid but not enabled. Delete (3) removes an entry from the table. Invalid (4) defines an entry that is no longer valid (e.g., an entry that was deleted) and should be ignored. An attempt to set a value of invalid (4) causes the agent to return SNMP_BADVALUE.

OBJECT-IDENTITY

OBJECT-TYPE

IP Address specified in the last request.

OBJECT-TYPE

UDP port specified in the last request.

OBJECT-TYPE

Last community string used.

OBJECT-TYPE

Last login user name used.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

Enables/disables IGMP Snooping on this device. The default value is disable.

OBJECT-TYPE

The timeout period in seconds for aging out Multicast Groups dynamically learned with IGMP Snooping. Note that aging operates on a per interface per multicast group basis. This interval is also used to age out ports that have received IGMP Router Query PDUs. The default is 260 seconds and the range is 3 to 3600 seconds.

OBJECT-TYPE

Sets the mode how unknown Multicast packets will be treated. The default value is flood(2).

OBJECT-TYPE

The timeout period in seconds approximately for aging out Unknown Multicast Groups dynamically learned with traffic snooping. The exactly value is UnknownLookupInterval/(UnknownLookupInterval-UnknownLookupResponseTime)*UnknownAgingTime. Note that aging operates on a per unknown multicast group basis. The default is 260 seconds and the range is 3 to 3600 seconds.

OBJECT-TYPE

The frequency at which Unknown Multicast Groups dynamically learned with traffic snooping are traffic checked by the switch in seconds. So this is the time between periodic traffic checking in which unknown multicast groups being aged on the switch when it is acting as Trafficsnooper. Large values lead to traffic checking less often. The default is 125 seconds and the range is 2 to 3599 seconds.

OBJECT-TYPE

The unknown lookup response time in seconds in which Unknown Multicast Groups dynamically learned with traffic snooping are traffic checked. So this is the time in which response traffic to the Trafficsnooper allowing the update of unknown multicast group aging timer. This variable enables the checking of bursty unknown multicast traffic. Small values lead to bad traffic checking but few snooper load and large values lead to good traffic checking but more snooper load. The default is 10 seconds and the range is 1 to 3598 seconds.

OBJECT-TYPE

Enables or disables the addition of query ports to multicast filter portmasks.

OBJECT-TYPE

Shows the IP address of the active querier.

OBJECT-TYPE

A table displaying the IGMP Router Query PDU ports.

OBJECT-TYPE

A table displaying the IGMP Router Query PDU ports. These are maintained on a per VLAN basis.

OBJECT-TYPE

This is the VLAN index for which this entry is valid. If the switch only supports shared vlan learning (SVL), the value is always 1 and there is only 1 instance in the table.

OBJECT-TYPE

This read-only object displays the set of ports that have received IGMP Router Query PDUs for this VLAN as determined by the IGMP Snooping task.

OBJECT-TYPE

A table containing the multicast filtering information on a per vlan basis learned with IGMP Snooping.

OBJECT-TYPE

The entry of the hmIGMPSnoopFilterTable.

OBJECT-TYPE

This is the VLAN index for which this entry is valid. If the switch only supports shared vlan learning (SVL), the value is always 1 and there is only 1 instance in the table.

OBJECT-TYPE

The multicast destination MAC address in a frame to which this entry's filtering information applies.

OBJECT-TYPE

The set of ports, to which frames destined for this Group MAC Address learned by IGMP Snooping are currently being forwarded. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'. (Note that the setting of the bit corresponding to the port from which a frame is received is irrelevant.)

OBJECT-TYPE

A table containing forwarding information for each VLAN, specifying the set of ports to which forwarding of all multicasts applies, configured statically by management. An entry appears in this table for all VLANs that are currently instantiated.

OBJECT-TYPE

Forwarding information for a VLAN, specifying the set of ports to which all multicasts should be forwarded, configured statically by management.

OBJECT-TYPE

This is the VLAN index for which this entry is valid. If the switch only supports shared vlan learning (SVL), the value is always 1 and there is only 1 instance in the table.

OBJECT-TYPE

The set of ports configured by management in this VLAN to which all multicast group-addressed frames learned by IGMP are to be forwarded. This value will be restored after the device is reset.

OBJECT-TYPE

A table displaying the IGMP Static Query ports.

OBJECT-TYPE

The entry of the hmIGMPSnoopQueryStaticTable.

OBJECT-TYPE

This is the VLAN index for which this entry is valid. If the switch only supports shared vlan learning (SVL), the value is always 1 and there is only 1 instance in the table.

OBJECT-TYPE

The set of ports explicitly configured by management to be IGMP-forwarding ports.

OBJECT-TYPE

The set of ports that are automatically learned by LLDP protocol to be IGMP-forwarding ports.

OBJECT-TYPE

The set of ports that are allowed to be learned automatically by LLDP protocol to be IGMP-forwarding ports.

OBJECT-IDENTITY

OBJECT-TYPE

Enables/disables IGMP Querier on this device. IGMP queries are only sent when hmIGMPSnoopStatus is also set. The default value is disable.

OBJECT-TYPE

Shows the current mode of the IGMP Querier.

OBJECT-TYPE

The frequency at which IGMP general query packets are transmitted by the querying switch in seconds. So this is the time between general periodic queries being sent out of the switch when it is acting as the IGMP querier. Large values lead to IGMP queries being sent less often. The default is 125 seconds and the range is 2 to 3599 seconds. Note: The following dependency is needed: Max. Response Time < Querier Transmit Interval < Group Membership Interval.

OBJECT-TYPE

The maximum query response time in seconds advertised in IGMP v2 queries on this VLAN if the switch is the querier. Smaller values allow a switch to prune groups faster. So it is the maximum response time inserted into the general periodic queries. This variable enables the tuning of the burstiness of the IGMP traffic. If it is increased the responses have a larger time span in which to be generated by the hosts. The default is 10 seconds and the range is 1 to 3598 seconds.

OBJECT-TYPE

The Querier protocol version. The default is version 2.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

Sets the mode how unknown multicast packets will be treated. The default value is flood(2).

OBJECT-IDENTITY

OBJECT-TYPE

Enables/disables the DHCP Option 82 defined in RFC 3046 on this device.

OBJECT-TYPE

This option determines the content of the Agent Remote ID (sub-option 2). ip(1) inserts the ip address of the relay's mgmt-interface and encodes it with sub option type A1. mac(2) inserts the mac adress of the relay's mgmt-interface and encodes it with sub option type 00. client-id(3) inserts the client identifier (sysName) of the relay's mgmt-interface and encodes it with sub option type A2. other(4) inserts the value in hmRelayOptionRemoteIDValue and encodes it with sub option type A3.

OBJECT-TYPE

Displays the actual content of the Remote ID sub option for this relay agent. The value is encoded in TLV (Type-Length-Value) format. The following type values are currently defined: 00 = mac adress A1 = ip address A2 = client identifier A3 = string in hmRelayOptionRemoteIDValue

OBJECT-TYPE

Contains an octet string to be used as value for Agent Remote ID Sub-option type A3

OBJECT-IDENTITY

OBJECT-TYPE

This object is 'obsolete' and is replaced by hmRelayServerAddrEntry. The IP address of the first DHCP-server to be addressed by the relay agent. If 0.0.0.0, DHCP relaying is switched off for this entry.

OBJECT-TYPE

This object is 'obsolete' and is replaced by hmRelayServerAddrEntry. The IP address of the second DHCP-server to be addressed by the relay agent. If 0.0.0.0, DHCP relaying is switched off for this entry.

OBJECT-TYPE

This object is 'obsolete' and is replaced by hmRelayServerAddrEntry. The IP address of the third DHCP-server to be addressed by the relay agent. If 0.0.0.0, DHCP relaying is switched off for this entry.

OBJECT-TYPE

This object is 'obsolete' and is replaced by hmRelayServerAddrEntry. The IP address of the fourth DHCP-server to be addressed by the relay agent. If 0.0.0.0, DHCP relaying is switched off for this entry.

OBJECT-TYPE

This table contains variables for each interface of the switch.

OBJECT-TYPE

The entry of the hmRelayInterfaceTable.

OBJECT-TYPE

index to identify an interface card. This value is never greater than hmSysGroupCapacity.

OBJECT-TYPE

index to identify an interface within an interface card.

OBJECT-TYPE

Enable or disable DHCP Option 82 on this physical port.

OBJECT-TYPE

Enable or disable relaying of incoming broadcasted BOOTP/DHCP request packets on this physical port. Hirschmann Multicast BOOTP/DHCP requests will always be relayed.

OBJECT-TYPE

Contains the actual Circuit ID sub option for this interface of the relay agent. It is a best guess value, since some information is not known before the actual reception of a BOOTP/DHCP request message.

OBJECT-TYPE

Enable or disable DHCP Relay Agent on this physical port.

OBJECT-TYPE

Current active DHCP protocol on this physical port.

OBJECT-TYPE

This table contains objects to configure DHCP Servers.

OBJECT-TYPE

The DHCP Server objects.

OBJECT-TYPE

Index for server table.

OBJECT-TYPE

The address of the external DHCP server.

OBJECT-TYPE

If an Interface is set, only DHCP packets from this interface are relayed to the server.

OBJECT-TYPE

Indicates the status of an entry in this table, and is used to create/delete entries. Objects within this table can by changed while the status is 'active'.

OBJECT-TYPE

The number of BOOTP/DHCP broadcast request packets received by the relay agent.

OBJECT-TYPE

The number of BOOTP/DHCP multicast request packets received by the relay agent.

OBJECT-TYPE

The number of BOOTP/DHCP requests relayed to the DHCP Server.

OBJECT-TYPE

The number of BOOTP/DHCP replies relayed to the Client.

OBJECT-TYPE

The number of errors encountered within the relay agent.

OBJECT-TYPE

The last duplicate ip address encounterd by the relay agent.

OBJECT-IDENTITY

OBJECT-TYPE

This table contains all variables to configure the behaviour of the signalling contacts.

OBJECT-TYPE

The entry of the hmSigConConfigTable.

OBJECT-TYPE

This index is used to identify the associated signalling contact.

OBJECT-TYPE

Determines wether a trap shall be sent or not, when the signal contact operating state changes.

OBJECT-TYPE

This object identifies the cause for a trap. The index of the entity which produces the trap is specified by hmSigConTrapCauseIndex.

OBJECT-TYPE

This attribute specifies the entity which produces the trap. 1 - n: index of powersupply table / interfaces table 0: other errors

OBJECT-TYPE

This attribute specifies the behaviour of the relay contact. The factory settings for signal contact 1 is monitoring the correct operation of entries specified to be survied. When the device has also a second signal contact, the factory setting for it is the manual mode.

OBJECT-TYPE

When operating in manual mode, the signal contact state can be set by this attribute.

OBJECT-TYPE

This attribute shows the current operating state of the signal contact.

OBJECT-TYPE

Sets the monitoring of the network connection(s).

OBJECT-TYPE

Sets the monitoring of the ring/network coupling.

OBJECT-TYPE

Sets the monitoring of the HIPER-Ring, MRP-Ring or Fast HIPER-Ring.

OBJECT-TYPE

Sets the monitoring of the power supply 1.

OBJECT-TYPE

Sets the monitoring of the power supply 2.

OBJECT-TYPE

Sets the monitoring of the device temperature.

OBJECT-TYPE

Sets the monitoring of module removal (platform dependant).

OBJECT-TYPE

Sets the monitoring of the auto configuration adapter removal.

OBJECT-TYPE

Sets the monitoring of the power supply 3 (platform dependant).

OBJECT-TYPE

Sets the monitoring of the power supply 4 (platform dependant).

OBJECT-TYPE

Sets the monitoring of the cooling fan (platform dependant).

OBJECT-TYPE

Sets the monitoring of the power supply 5 (platform dependant).

OBJECT-TYPE

Sets the monitoring of the power supply 6 (platform dependant).

OBJECT-TYPE

Sets the monitoring of the power supply 7 (platform dependant).

OBJECT-TYPE

Sets the monitoring of the power supply 8 (platform dependant).

OBJECT-TYPE

Sets the monitoring whether the configuration on ACA is in sync with the configuration in NVRAM.

OBJECT-TYPE

Sets the monitoring of sub-rings if configured and activated on the device.

OBJECT-TYPE

This table contains all variables to mask an alarm for the signalling relay, produced by a link. The index for a link corresponds with ifMauIfIndex. The table is also used for the device monitoring configuration.

OBJECT-TYPE

The entry of the hmSigConLinkTable.

OBJECT-TYPE

This index is used to identify the associated link and corresponds with ifMauIfIndex.

OBJECT-TYPE

Indicates whether an alarm for the signalling relay of the associated link will be produced or not, so you can mask the value of ifMauMediaAvailable.

OBJECT-TYPE

This table contains all variables to configure the behaviour of the device state.

OBJECT-TYPE

Configuration of the device monitoring.

OBJECT-TYPE

This index is used to identify the associated device status (currently only one).

OBJECT-TYPE

Determines wether a trap shall be sent or not, when the device monitoring state changes.

OBJECT-TYPE

This object identifies the cause for a trap. The index of the entity which produces the trap is specified by hmDevMonTrapCauseIndex.

OBJECT-TYPE

This attribute specifies the entity which produces the trap. 1 - n: index of powersupply table / interfaces table 0: other errors

OBJECT-TYPE

This attribute shows the current state of the device monitoring.

OBJECT-TYPE

Sets the monitoring of the network connection(s).

OBJECT-TYPE

Sets the monitoring of the ring/network coupling.

OBJECT-TYPE

Sets the monitoring of the HIPER-Ring, MRP-Ring or Fast HIPER-Ring.

OBJECT-TYPE

Sets the monitoring of the power supply 1.

OBJECT-TYPE

Sets the monitoring of the power supply 2.

OBJECT-TYPE

Sets the monitoring of the device temperature.

OBJECT-TYPE

Sets the monitoring of module removal (platform dependant).

OBJECT-TYPE

Sets the monitoring of the auto configuration adapter removal.

OBJECT-TYPE

Sets the monitoring of the power supply 3 (platform dependant).

OBJECT-TYPE

Sets the monitoring of the power supply 4 (platform dependant).

OBJECT-TYPE

Sets the monitoring of the cooling fan (platform dependant).

OBJECT-TYPE

Sets the monitoring of the power supply 5 (platform dependant).

OBJECT-TYPE

Sets the monitoring of the power supply 6 (platform dependant).

OBJECT-TYPE

Sets the monitoring of the power supply 7 (platform dependant).

OBJECT-TYPE

Sets the monitoring of the power supply 8 (platform dependant).

OBJECT-TYPE

Sets the monitoring whether the configuration on ACA is in sync with the configuration in NVRAM.

OBJECT-TYPE

Sets the monitoring of sub-rings if configured and activated on the device.

OBJECT-IDENTITY

OBJECT-TYPE

Creates a new SNMP Community entry. Defaults: IPAddress 0.0.0.0 IpMask 0.0.0.0 AccessMode read-only Status config

OBJECT-TYPE

A table of the switch's SNMP Config entries

OBJECT-TYPE

Switch's SNMP Config entry

OBJECT-TYPE

The switch's Snmp Community Index

OBJECT-TYPE

The switch's Snmp Community Name This name identifies each SNMP community; the name can be up to 32 characters, and it is case-sensitive. Community names in the SNMP community must be unique. If you make multiple entries using the same community name, the first entry is kept and processed and all duplicate entries are ignored.

OBJECT-TYPE

The switch's Snmp Community IP Address Client IP Address - This attribute is an IP address (or portion thereof) from which this device will accept SNMP packets with the associated community. The requesting entity's IP address is logical-ANDed with the Client IP Mask and the result must match the Client IP Address. Note: If the Client IP Mask is set to 0.0.0.0, a Client IP Address of 0.0.0.0 matches all IP addresses.

OBJECT-TYPE

The switch's Snmp Community IP Mask Client IP Mask - This attribute is a mask to be logical-ANDed with the requesting entity's IP address before comparison with the Client IP Address. If the result matches with Client IP Address then the address is an authenticated IP address. For example, if the Client IP Address is 9.47.128.0 and the corresponding Client IP Mask is 255.255.255.0, a range of incoming IP addresses would match, that is, the incoming IP addresses could be a value in the following range: 9.47.128.0 to 9.47.128.255. To have a specific IP address be the only authenticated IP address, set the Client IP Address to the required IP address and set the Client IP Mask to 255.255.255.255.

OBJECT-TYPE

The switch's Snmp Community Access Mode Access Mode - This value can be read-only or read/write. A community with a read-only access allows for switch information to be displayed. A community with a read/write access allows for configuration changes to be made and for information to be displayed.

OBJECT-TYPE

The switch's Snmp Community Status. active(1) - This community is active, allowing SNMP managers associated with this community to manage the switch according to its access right. notInService(2) - This community is not active; no SNMP requests using this community will be accepted. In this case the SNMP manager associated with this community cannot manage the switch until the Status is changed back to active(1). config(3) - The community Status must be set to this value in order to configure it. When creating a new community entry, initial Status will be set to this value. destroy(4) - Set to this value to remove the community from the agent.

OBJECT-TYPE

Creates a new trap receiver entry. Defaults: IPAddress 0.0.0.0 status config

OBJECT-TYPE

Trap messages are sent across a network to an SNMP Network Manager. These messages alert the manager to events occurring within the switch or on the network. Up to six simultaneous trap receivers are supported.

OBJECT-TYPE

Switch's Snmp Trace Receiver Config entry

OBJECT-TYPE

The switch's Snmp Trap Receiver Index

OBJECT-TYPE

The switch's Snmp Trap Receiver Community Name. This is the SNMP community name of the remote network manager; the name can be up to 16 characters, and is case-sensitive.

OBJECT-TYPE

IP Address - Each IP address parameter is four integer numbers. The numbers range from 0 to 255.

OBJECT-TYPE

The switch's Snmp Trap Reciever Status. active(1) - This trap receiver is active, allowing SNMP Traps to be sent to this receiver. notInService(2) - This trap reciever is not active; no SNMP Traps will be sent to this reciever until it's set back to active(1). config(3) - The trap reciever Status must be set to this value in order to configure it. When creating a new trap receiver entry, the Status will initially be set to this value. Note: hmAgentSnmpTrapReceiverIPAddress must be set to non-zero before changing to active(1) or notInService(2). destroy(4) - Set to this value to remove the trap receiver entry from the agent.

OBJECT-IDENTITY

OBJECT-TYPE

Authentication Flag - Enable/Disable authentication Flag.

OBJECT-TYPE

Link Up/Down Flag - Enable/Disable Link Up/Link Down traps for the entire switch. When set to Enable, the Link Up/Down traps will be sent only if the Link Trap flag setting associated with the port (Port Configuration Menu) is set to Enable.

OBJECT-TYPE

Multiple Users Flag - Enable/Disable Multiple User traps. When the value is set to Enable, a Multiple User Trap is sent whenever someone logs in to the terminal interface (EIA 232 or Telnet) and there is already an existing terminal interface session.

OBJECT-TYPE

Spanning Tree Flag - This flag enables the sending of new root traps and topology change notification traps.

OBJECT-TYPE

Broadcast Storm Flag - This flag enables or disables the broadcast storm trap. You must also enable Broadcast Storm Recovery Mode (see the Switch Configuration Menu). When this value is set to Enable and Broadcast Storm Recovery mode is set to Enable, the Broadcast Storm Start/End traps are sent when the switch enters and leaves Broadcast Storm Recovery.

OBJECT-TYPE

Chassis Flag - Enable/Disable traps for hmTemperatureTrap hmModuleMapChange hmPowerSupplyTrap hmAutoconfigAdapterTrap

OBJECT-TYPE

Chassis Flag - Enable/Disable traps hmRingRedReconfig and hmRingCplReconfig

OBJECT-TYPE

PortSecurity Flag - enable/disable all port security traps.

OBJECT-TYPE

Max number of Entries in hmAgentSnmpCommunityConfigEntry

OBJECT-TYPE

Max number of Entries in hmAgentSnmpTrapReceiverConfigEntry

OBJECT-IDENTITY

OBJECT-TYPE

Enable logging of SNMP GET requests.

OBJECT-TYPE

Enable logging of SNMP SET requests.

OBJECT-TYPE

Define the log severity for SNMP GET requests.

OBJECT-TYPE

Define the log severity for SNMP SET requests.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

Enables/disables Power over Ethernet on this device. The default value is enable.

OBJECT-TYPE

Enables/disables port scanning on this device. The default value is enable.

OBJECT-TYPE

Reserved system power for active Power over Ethernet ports in Watts.

OBJECT-TYPE

Enables/disables Fast Power over Ethernet on this device. The default value is disabled.

OBJECT-TYPE

This table contains variables for each Power over Ethernet interface of the switch.

OBJECT-TYPE

The entry of the hmPOEPortTable.

OBJECT-TYPE

Index to identify an Power over Ethernet interface.

OBJECT-TYPE

Measured usage power per interface expressed in Milliwatts.

OBJECT-TYPE

The maximum observed power consumption (hmPOEPortConsumptionPower) value expressed in milliwatts used by the PD. The value is reset to 0 if the PoE admin state is set to disable or if a disconnect of the PD is detected.

OBJECT-TYPE

The power limit per port expressed in milliwatts. If set to zero the power consumption limitation is disabled.

OBJECT-TYPE

This table contains objects for each plugged PoE+ module of the switch. If the device is non-modular and supports PoE+ it contains only one entry.

OBJECT-TYPE

The entries of the hmPOEModuleTable.

OBJECT-TYPE

Slot number of the plugged PoE+ module.

OBJECT-TYPE

Configurable power budget per module expressed in Watts. The default value is hmPOEModuleMaximumPower and depends on the hardware.

OBJECT-TYPE

Maximum available power budget per module expressed in Watts. This value depends on the device or module.

OBJECT-TYPE

The reserved power (depending on actual power classes) per module expressed in Watts.

OBJECT-TYPE

The measured usage power per module expressed in Watts.

OBJECT-TYPE

The usage power threshold per module expressed in percent. If this threshold is exceeded a alarm is initiated.

OBJECT-TYPE

This object controls, on a per-module basis, whether or not notifications from the agent are enabled.

OBJECT-IDENTITY

OBJECT-TYPE

Enable or disable the resources measurement If disabled, the task - needed for measurement - is also deleted.

OBJECT-IDENTITY

OBJECT-TYPE

The current cpu utilization of the switch in percent.

OBJECT-TYPE

The average cpu utilization of the switch in percent, max. measured over the last 30 minutes.

OBJECT-TYPE

The current number of processes running.

OBJECT-TYPE

The maximum number of processes running, max. since the last 30 minutes.

OBJECT-IDENTITY

OBJECT-TYPE

The current allocated memory of the switch in kBytes.

OBJECT-TYPE

The current free memory of the switch in kBytes.

OBJECT-TYPE

The average allocated memory of the switch in kBytes, measured over the last 30 minutes.

OBJECT-TYPE

The average free memory of the switch in kBytes, measured over the last 30 minutes.

OBJECT-IDENTITY

OBJECT-TYPE

The current network utilization of the internal cpu interface in percent.

OBJECT-TYPE

The average network utilization of the internal cpu interface in percent, measured over the last 30 minutes.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

Enables/disables the ProfinetIO functionality on this device. If disabled(2), the ProfinetIO protocol is inactive, but the ProfinetIO MIBs can be accessed. The default value is disabled.

OBJECT-TYPE

Identifier of the device family. Values 1 .. 65635 are valid device IDs.

OBJECT-TYPE

Identifier ID of the device of port or module.

OBJECT-TYPE

Product (switch) order ID. The size is restricted to 64 characters.

OBJECT-TYPE

Switch device type details, for example: 4 Port Rail Switch.

OBJECT-TYPE

This value is a string that contains Version number of software in profinetio format, for example: 01.0.03.

OBJECT-TYPE

Version number of switch hardware in profinetio format.

OBJECT-TYPE

Product (switch) order ID. The size is restricted to 32 characters (In the form of the 9-th numbers).

OBJECT-TYPE

Table of DCP mode entries

OBJECT-TYPE

DCP mode entry

OBJECT-TYPE

Port ID for the DCP mode table entry

OBJECT-TYPE

DCP mode for one port. Allowed values none(0), ingress(1), egress(2) or both(3) which is default.

OBJECT-TYPE

Device name. The size is restricted to 240 characters. It must be conform to the restrictions as decribed in PNIO protocol specification.

OBJECT-TYPE

Returns the number of active application relations.

OBJECT-IDENTITY

OBJECT-IDENTITY

Set not allowed, a Profinet application relation is active.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

Enables/disables the EtherNet/IP(TM) functionality on this device. If disabled(2), the EtherNet/IP protocol is deactivated, but the EtherNet/IP MIBs can be accessed. The default value is disabled.

OBJECT-TYPE

Read the error code within EtherNet/IP(TM) action.

OBJECT-TYPE

Read the Product Code as shown in the Identity Object of EtherNet/IP(TM). Values 1 .. 65635 are valid product codes.

OBJECT-TYPE

Read the major revision number as shown in the Identity Object of EtherNet/IP(TM). Values 1 .. 255 are valid revisions.

OBJECT-TYPE

Read the minor revision number as shown in the Identity Object of EtherNet/IP(TM). Values 1 .. 255 are valid revisions.

OBJECT-TYPE

Read the product name as shown in the Identity Object of EtherNet/IP(TM). The size is restricted to 32 Characters.

OBJECT-TYPE

Read the catolog name as provided in the EDS file for EtherNet/IP(TM). The size is restricted to 255 Characters.

OBJECT-IDENTITY

OBJECT-TYPE

Statistics: number of connections that have been established within EtherNet/IP.

OBJECT-TYPE

Statistics: number of connection timeouts that have been occurred within EtherNet/IP.

OBJECT-TYPE

Statistics: number of requests to the vendor specific objects within EtherNet/IP.

OBJECT-IDENTITY

OBJECT-TYPE

Enables/disables the IEC61850 MMS server functionality on this device. If disabled(2), the MMS Server is deactivated, but the IEC61850 MIBs can be accessed. The default value is disabled.

OBJECT-TYPE

Enables/disables the Read/Write capability of the IEC61850 MMS. If disabled(2), the MMS Server is accessible Read-Only, if enabled(2) the devices configuration can be changed using the IEC61850 MMS protocol. The default value is disabled.

OBJECT-TYPE

The IEC61850 MMS server technical key setting corresponds to the IEC61850 IED name. This name is used to identify the device via a IEC61850 MMS client. The size is restricted to 32 characters. According to IEC61850-7-2 Ed. the TechnicalKey represents an IEC61850 VisibleString. Thus the following characters are allowed: VisibleString ( FROM ('A'|'a'|'B'|'b'|'C'|'c'|'D'|'d'|'E'|'e'|'F'|'f'| 'G'|'g'|'H'|'h'|'I'|'i'|'J'|'j'|'K'|'k'|'L'|'l'| 'M'|'m'|'N'|'n'|'O'|'o'|'P'|'p'|'Q'|'q'|'R'|'r'| 'S'|'s'|'T'|'t'|'U'|'u'|'V'|'v'|'W'|'w'|'X'|'x'| 'Y'|'y'|'Z'|'z'|'_'|'0'|'1'|'2'|'3'|'4'|'5'|'6'| '7'|'8'|'9') )

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

The text added in this variable by the user will be displayed in the system login page as banner on every login into the CLI (local or remote) or when performing login into the system web interface. The default value is an empty string, which will not be displayed. Special meaning have the sequences '\t' and '\n' which allow the user to format the string with tabulator (t) and newline (n) format instructions. The percent character ('%') is not allowed.

OBJECT-TYPE

Enables/disables the display of the pre login banner text.

OBJECT-TYPE

The text added in this variable by the user will be displayed in the system login page (local or remote) instead of the systemoverview. The default value is an empty string. Special meaning have the sequences '\t' and '\n' which allow the user to format the string with tabulator (\t) and newline (\n) format instructions. The Banner must be enabled using hmAgentCliBannerAdminStatus.

OBJECT-TYPE

Enables/disables the display of the cli login banner text instead of the standard login banner.

OBJECT-IDENTITY

OBJECT-TYPE

Global switch to enable / disable the port state actions, which are performed if a condition becomes true

OBJECT-TYPE

Port state mode interface table.

OBJECT-TYPE

Port state mode interface entry.

OBJECT-TYPE

Port monitor interface mode.

OBJECT-TYPE

Port monitor interface reset.

OBJECT-TYPE

Interface link disable state.

OBJECT-IDENTITY

OBJECT-TYPE

Port state condition interface table.

OBJECT-TYPE

Port state action interface entry.

OBJECT-TYPE

Interface link flap mode.

OBJECT-TYPE

Interface CrcFragments mode.

OBJECT-TYPE

Condition type field.

OBJECT-TYPE

Interface Overload Detection mode.

OBJECT-TYPE

Interface Speed and Duplex monitor mode.

OBJECT-IDENTITY

OBJECT-TYPE

Measure interval in seconds (1-180s) for link flap detection.

OBJECT-TYPE

Link flap counter (1-100).

OBJECT-TYPE

Port condition link flap interface table.

OBJECT-TYPE

Port condition link flap interface entry.

OBJECT-TYPE

Link flap count that occured in last interval.

OBJECT-TYPE

Total link flap count.

OBJECT-IDENTITY

OBJECT-TYPE

Measure interval in seconds (5-180s) for CrcFragments detection.

OBJECT-TYPE

CrcFragments counter (1-1000000).

OBJECT-TYPE

Port condition CrcFragments interface table.

OBJECT-TYPE

Port condition CrcFragments interface entry.

OBJECT-TYPE

CrcFragments count that occured in last interval.

OBJECT-TYPE

Total CrcFragments count.

OBJECT-IDENTITY

OBJECT-TYPE

Measure interval in seconds (1-20s) for overload detection.

OBJECT-TYPE

Port condition overload detection interface table.

OBJECT-TYPE

Port condition overload detection interface entry.

OBJECT-TYPE

Overload detection conditon traffic type.

OBJECT-TYPE

Overload detection conditon threshold type.

OBJECT-TYPE

Overload detection conditon lower threshold value.

OBJECT-TYPE

Overload detection condition upper threshold value.

OBJECT-IDENTITY

OBJECT-TYPE

Port condition speed-duplex interface table.

OBJECT-TYPE

Port condition speed-duplex interface entry.

OBJECT-TYPE

Speed and duplex combination allowed by port-monitor.

OBJECT-IDENTITY

OBJECT-TYPE

Port Auto Disable interface table.

OBJECT-TYPE

Port Auto Disable interface entry.

OBJECT-TYPE

Remaining time in seconds until the activation of the port.

OBJECT-TYPE

Name of the component that triggered the error

OBJECT-TYPE

Error disable reason

OBJECT-TYPE

Timer value in seconds after which a deactivated port is activated again. Possible values are: 30-2147483. A value of 0 disables the timer.

OBJECT-TYPE

Port Auto Disable interface reset.

OBJECT-TYPE

Status of Auto Disable interface admin state

OBJECT-TYPE

Possible reasons for Auto Disable

OBJECT-TYPE

Port Auto Disable interface entry.

OBJECT-TYPE

Reason for deactivation a port

OBJECT-TYPE

Enables/disables recovery by reason on this device.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

Enable or disable MAC Notification global.

OBJECT-TYPE

MAC Notification interval in seconds. Range is between 0 and 2147483647.

OBJECT-IDENTITY

OBJECT-TYPE

A table containing current configuration information for each interface.

OBJECT-TYPE

A logical row in the hmMACNotifyInterfaceTable.

OBJECT-TYPE

Enable or disable MAC Notification on this interface.

OBJECT-TYPE

Last MAC address on this interface that have been added or removed from the address table.

OBJECT-TYPE

Status of the last MAC address on this interface.

OBJECT-TYPE

Setting this object to 'add' (1) causes that only notifications are sent when entries are added to the FDB. Setting this object to 'remove' (2) causes that only notifications are sent when entries are removed from the FDB. Setting this object to 'addAndRemove' (3) causes that notifications are sent when entries are added or removed in the FDB.