MIBs Depot

HIRSCHMANN-MMP4-BASICL2-MIB

Registered at
1.3.6.1.4.1.248.15
Last updated
2005-11-22 12:00
Organization
Hirschmann Automation and Control GmbH
Revisions
2005-11-22 12:00, 2005-08-18 12:00, 2004-07-02 00:00
Namespace
hirschmann
Source file
HIRSCHMANN-MMP4-BASICL2-MIB
Digest
sha256:5cbc3524ca9cc2dddcf97d6b5bcaf035cf51fa5709660964964a57b16b377297

Description

The Hirschmann Private Platform4 Basic Layer 2 MIB definitions for Platform devices.

Contact

Customer Support Postal: Hirschmann Automation and Control GmbH Stuttgarter Str. 45-51 72654 Neckartenzlingen Germany Tel: +49 7127 14 1981 Web: http://www.hicomcenter.com/ E-Mail: hicomcenter@hirschmann.com

Imports

FromSymbols
HMPRIV-MGMT-SNMP-MIBHmAgentLogSeverity, hirschmann
IANAifType-MIBIANAifType
IEEE8021-PAE-MIBdot1xPaePortNumber
IF-MIBifIndex
INET-ADDRESS-MIBInetAddress
Q-BRIDGE-MIBVlanIndex, dot1qFdbId, dot1qVlanIndex
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP
SNMPv2-SMICounter32, Gauge32, Integer32, IpAddress, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso
SNMPv2-TCDisplayString, MacAddress, RowStatus, TEXTUAL-CONVENTION, TruthValue

Imported by

3 module(s) in this corpus import this one.

Load order

Every file a consumer needs in order to load this module, dependencies first.

BRIDGE-MIB
HIRSCHMANN-MMP4-BASICL2-MIB
HMPRIV-MGMT-SNMP-MIB
IANA-ADDRESS-FAMILY-NUMBERS-MIB
IANAifType-MIB
IEEE8021-PAE-MIB
IF-MIB
INET-ADDRESS-MIB
P-BRIDGE-MIB
Q-BRIDGE-MIB
RFC1158-MIB
RFC1271-MIB
RMON-MIB
RMON2-MIB
SNMP-FRAMEWORK-MIB
SNMPv2-CONF
SNMPv2-MIB
SNMPv2-SMI
SNMPv2-TC
TOKEN-RING-RMON-MIB

Under this module's arcs

Where the registration tree carries on below this module.

ArcNameModule
1.3.6.1.4.1.248.15.2hmPlatform4RoutingHIRSCHMANN-MMP4-ROUTING-MIB
1.3.6.1.4.1.248.15.3hmPlatform4QOSHIRSCHMANN-MMP4-QOS-MIB
1.3.6.1.4.1.248.15.4hmPlatform4MulticastHIRSCHMANN-MULTICAST-MIB

Textual conventions

NameOIDSyntaxAccessStatus
BridgeId
TEXTUAL-CONVENTION
the Bridge-Identifier as used in the Spanning Tree
current
HmAgentDot1xPortControlMode
TEXTUAL-CONVENTION
The control values of the Authenticator PAE controlled Port.
current
HmAgentDot1xSessionTerminationAction
TEXTUAL-CONVENTION
The action to be taken on session termination .
current
HmAgentPortMask
TEXTUAL-CONVENTION
Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0' When setting this value, the system will ignore configuration for ports not between the first and last valid ports. Configuration of any port numbers between this range that are not valid ports return a failure message, but will still apply configuration for valid ports.
current

Objects

NameOIDSyntaxAccessStatus
hmPlatform4
OBJECT-IDENTITY
1.3.6.1.4.1.248.15
hmAgentInfoGroup
OBJECT-IDENTITY
1.3.6.1.4.1.248.15.1.1
hmAgentTrapLogGroup
OBJECT-IDENTITY
1.3.6.1.4.1.248.15.1.1.2
hmAgentTrapLogTotal
OBJECT-TYPE
The total number of traps sent since last reset.
1.3.6.1.4.1.248.15.1.1.2.1Integer32read-onlycurrent
hmAgentTrapLogTotalSinceLastViewed
OBJECT-TYPE
The number of traps sent since last viewed.
1.3.6.1.4.1.248.15.1.1.2.3Integer32read-onlydeprecated
hmAgentTrapLogTable
OBJECT-TYPE
Agent Trap Log
1.3.6.1.4.1.248.15.1.1.2.4not-accessiblecurrent
hmAgentTrapLogEntry
OBJECT-TYPE
Agent trap log entry
1.3.6.1.4.1.248.15.1.1.2.4.1not-accessiblecurrent
hmAgentTrapLogIndex
OBJECT-TYPE
Unique index of trap entry
1.3.6.1.4.1.248.15.1.1.2.4.1.1Integer32read-onlycurrent
hmAgentTrapLogSystemTime
OBJECT-TYPE
System uptime when trap was sent. This entry shows how long the system has been up when the trap occurred.
1.3.6.1.4.1.248.15.1.1.2.4.1.2DisplayStringread-onlycurrent
hmAgentTrapLogTrap
OBJECT-TYPE
Description of the trap sent.
1.3.6.1.4.1.248.15.1.1.2.4.1.3DisplayString (SIZE(0..512))read-onlycurrent
hmAgentConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.248.15.1.2
hmAgentCLIConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.248.15.1.2.1
hmAgentLoginSessionTable
OBJECT-TYPE
A table of the switch's login session
1.3.6.1.4.1.248.15.1.2.1.1not-accessiblecurrent
hmAgentLoginSessionEntry
OBJECT-TYPE
Login Session Entry
1.3.6.1.4.1.248.15.1.2.1.1.1not-accessiblecurrent
hmAgentLoginSessionIndex
OBJECT-TYPE
Agent Login Session Index of the switch
1.3.6.1.4.1.248.15.1.2.1.1.1.1Integer32read-onlycurrent
hmAgentLoginSessionUserName
OBJECT-TYPE
Agent Login Session UserName of the switch
1.3.6.1.4.1.248.15.1.2.1.1.1.2DisplayStringread-onlycurrent
hmAgentLoginSessionIPAddress
OBJECT-TYPE
Agent Login Session IP Address of the switch
1.3.6.1.4.1.248.15.1.2.1.1.1.3IpAddressread-onlycurrent
hmAgentLoginSessionConnectionType
OBJECT-TYPE
Agent Login Session Connection Type of the switch
1.3.6.1.4.1.248.15.1.2.1.1.1.4INTEGER {serial(1), telnet(2)}read-onlycurrent
hmAgentLoginSessionIdleTime
OBJECT-TYPE
Agent Login Session Idle Time of the switch
1.3.6.1.4.1.248.15.1.2.1.1.1.5TimeTicksread-onlycurrent
hmAgentLoginSessionSessionTime
OBJECT-TYPE
Agent Login Session Time of the switch
1.3.6.1.4.1.248.15.1.2.1.1.1.6TimeTicksread-onlycurrent
hmAgentLoginSessionStatus
OBJECT-TYPE
Status of the user. active(1) - This connection is active. destroy(6) - Set to this value to disconnect this user.
1.3.6.1.4.1.248.15.1.2.1.1.1.7RowStatusread-writecurrent
hmAgentTelnetConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.248.15.1.2.1.2
hmAgentTelnetLoginTimeout
OBJECT-TYPE
Telnet login timeout (minutes) Config telnet timeout will set the telnet session timeout value. A session is active as long as the session has not remained idle for the value set. Specify a value from 1 to 160. Note: Changing the timeout value for active sessions does not become effective until the session is reaccessed. Any keystroke will also activate the new timeout duration.
1.3.6.1.4.1.248.15.1.2.1.2.1Integer32 (1..160)read-writecurrent
hmAgentTelnetMaxSessions
OBJECT-TYPE
Maximum number of Telnet Sessions Config telnet maxsessions is an integer value from 0 to 5 that specifies the maximum number of telnet sessions that can be established. If the value is 0, no Telnet session can be established.
1.3.6.1.4.1.248.15.1.2.1.2.2Integer32 (0..5)read-writecurrent
hmAgentTelnetAllowNewMode
OBJECT-TYPE
Allow new telnet sessions (enable or disable) Config telnet disable means that no new Telnet sessions are to be established. Any already established session remains active until the session is ended or an abnormal network error ends it.
1.3.6.1.4.1.248.15.1.2.1.2.3INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentUserConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.248.15.1.2.1.3
hmAgentUserConfigCreate
OBJECT-TYPE
Create a new user. When set with a non-empty string, a new user with that name will be created. This object will only return an empty string. This string is limited to alpha-numeric strings (uncluding the '-' and '_' characters).
1.3.6.1.4.1.248.15.1.2.1.3.1DisplayString (SIZE(1..32))read-writecurrent
hmAgentUserConfigTable
OBJECT-TYPE
User Config Table
1.3.6.1.4.1.248.15.1.2.1.3.2not-accessiblecurrent
hmAgentUserConfigEntry
OBJECT-TYPE
User Config Entry
1.3.6.1.4.1.248.15.1.2.1.3.2.1not-accessiblecurrent
hmAgentUserIndex
OBJECT-TYPE
Agent User Config Index
1.3.6.1.4.1.248.15.1.2.1.3.2.1.1Integer32not-accessiblecurrent
hmAgentUserName
OBJECT-TYPE
Agent User Name. This string is limited to alpha-numeric strings (including the '-' and '_' characters).
1.3.6.1.4.1.248.15.1.2.1.3.2.1.2DisplayString (SIZE(1..32))read-writecurrent
hmAgentUserPassword
OBJECT-TYPE
Agent User Password This object will return an empty string even if a password is set.
1.3.6.1.4.1.248.15.1.2.1.3.2.1.3DisplayString (SIZE(0..32))read-writecurrent
hmAgentUserAccessMode
OBJECT-TYPE
Agent User Access Mode
1.3.6.1.4.1.248.15.1.2.1.3.2.1.4INTEGER {read(1), write(2)}read-writecurrent
hmAgentUserStatus
OBJECT-TYPE
Agent User Status. active(1) - This user account is active. destroy(6) - Set to this value to remove this user account.
1.3.6.1.4.1.248.15.1.2.1.3.2.1.5RowStatusread-writecurrent
hmAgentUserAuthenticationType
OBJECT-TYPE
SNMPv3 User Authentication. The user passsword must be set to a string greater than or equal to 8 characters for this to be set to anything but none(1). none(1) - no authentication used hmacmd5(1) - Use HMAC-MD5 authentication hmacsha(1) - Use HMAC-SHA authentication
1.3.6.1.4.1.248.15.1.2.1.3.2.1.6INTEGER {none(1), hmacmd5(2), hmacsha(3)}read-writecurrent
hmAgentUserEncryptionType
OBJECT-TYPE
SNMPv3 User Encryption Can not be set to des(2) if hmAgentUserAuthenticationType is set to none(1). none(1) - no encryption used des(2) - DES encryption used
1.3.6.1.4.1.248.15.1.2.1.3.2.1.7INTEGER {none(1), des(2)}read-writecurrent
hmAgentUserEncryptionPassword
OBJECT-TYPE
SNMPv3 User Encryption Password This object will return an empty string even if a password is set. hmAgentUserEncryptionType must be set to des(2) before this object can be configured. This object will return an empty string even if a password is set.
1.3.6.1.4.1.248.15.1.2.1.3.2.1.8DisplayString (SIZE(8..64))read-writecurrent
hmAgentUserDefaultPwdActive
OBJECT-TYPE
Shows if one or more default passwords are active for users configured in the hmAgentUserConfigTable.
1.3.6.1.4.1.248.15.1.2.1.3.248TruthValueread-onlycurrent
hmAgentLagConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.248.15.1.2.2
hmAgentLagConfigCreate
OBJECT-TYPE
Agent LAG Create. When this object is set with a non-empty string, a new LAG will be created if possible with the entered string as its name.
1.3.6.1.4.1.248.15.1.2.2.1DisplayString (SIZE(0 | 1..15))read-writecurrent
hmAgentLagSummaryConfigTable
OBJECT-TYPE
A summary table of the switch's LAG config entries
1.3.6.1.4.1.248.15.1.2.2.2not-accessiblecurrent
hmAgentLagSummaryConfigEntry
OBJECT-TYPE
Switch's LAG config entry
1.3.6.1.4.1.248.15.1.2.2.2.1not-accessiblecurrent
hmAgentLagSummaryLagIndex
OBJECT-TYPE
Agent LAG IfIndex. This value corresponds with the LAG interface in the ifTable.
1.3.6.1.4.1.248.15.1.2.2.2.1.1Integer32read-onlycurrent
hmAgentLagSummaryName
OBJECT-TYPE
Agent LAG Name. The associated name of the LAG used during creation.
1.3.6.1.4.1.248.15.1.2.2.2.1.2DisplayString (SIZE(1..15))read-writecurrent
hmAgentLagSummaryFlushTimer
OBJECT-TYPE
Agent LAG FlushTimer.
1.3.6.1.4.1.248.15.1.2.2.2.1.3Integer32read-writeobsolete
hmAgentLagSummaryLinkTrap
OBJECT-TYPE
Agent LAG LinkTrap. Configures sending Link Up/Down traps when the LAG interface goes Up or Down.
1.3.6.1.4.1.248.15.1.2.2.2.1.4INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentLagSummaryAdminMode
OBJECT-TYPE
Agent LAG AdminMode. Administratively enables or disables this LAG interface.
1.3.6.1.4.1.248.15.1.2.2.2.1.5INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentLagSummaryStpMode
OBJECT-TYPE
Agent LAG StpMode.
1.3.6.1.4.1.248.15.1.2.2.2.1.6INTEGER {off(3), on(4)}read-writecurrent
hmAgentLagSummaryAddPort
OBJECT-TYPE
Agent LAG AddPort. Set to a non 0 value to add a port to the LAG. Values correspond to ifIndex values in the ifTable. Note: hmAgentPortType for the port to be added must be full duplex and the same speed as previously added port(s), if any.
1.3.6.1.4.1.248.15.1.2.2.2.1.7Integer32read-writecurrent
hmAgentLagSummaryDeletePort
OBJECT-TYPE
Agent LAG DeletePort. Set to a non 0 value to remove a port from the LAG. Values correspond to ifIndex values in the ifTable.
1.3.6.1.4.1.248.15.1.2.2.2.1.8Integer32read-writecurrent
hmAgentLagSummaryStatus
OBJECT-TYPE
Agent LAG Status. active(1) - This LAG is enabled. destroy(6) - Set to this value to remove the LAG.
1.3.6.1.4.1.248.15.1.2.2.2.1.9RowStatusread-writecurrent
hmAgentLagSummaryType
OBJECT-TYPE
Agent LAG Type. static(1) - This LAG is staticly maintained. dynamic(2) - This LAG is dynamicly maintained.
1.3.6.1.4.1.248.15.1.2.2.2.1.10INTEGER {static(1), dynamic(2)}read-onlycurrent
hmAgentLagDetailedConfigTable
OBJECT-TYPE
A detailed table of the switch's LAG config entries
1.3.6.1.4.1.248.15.1.2.2.3not-accessiblecurrent
hmAgentLagDetailedConfigEntry
OBJECT-TYPE
Switch's LAG config entry
1.3.6.1.4.1.248.15.1.2.2.3.1not-accessiblecurrent
hmAgentLagDetailedLagIndex
OBJECT-TYPE
LAG index
1.3.6.1.4.1.248.15.1.2.2.3.1.1Integer32read-onlycurrent
hmAgentLagDetailedIfIndex
OBJECT-TYPE
LAG port index
1.3.6.1.4.1.248.15.1.2.2.3.1.2Integer32read-onlycurrent
hmAgentLagDetailedPortSpeed
OBJECT-TYPE
LAG port speed. See hmAgentPortType for a description and list of valid values.
1.3.6.1.4.1.248.15.1.2.2.3.1.3OBJECT IDENTIFIERread-onlycurrent
hmAgentLagDetailedPortStatus
OBJECT-TYPE
LAG port status. active(1) - Actively participating in the LAG. inactive(2) - Not participating in the LAG.
1.3.6.1.4.1.248.15.1.2.2.3.1.4INTEGER {active(1), inactive(2)}read-onlycurrent
hmAgentLagConfigStaticCapability
OBJECT-TYPE
Agent LAG Static Capability. Configures whether Static LAGs are supported on this device.
1.3.6.1.4.1.248.15.1.2.2.4INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentSpanningTreeConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.248.15.1.2.7
hmAgentSpanningTreeMode
OBJECT-TYPE
The switch's Spanning Tree Switch Status
1.3.6.1.4.1.248.15.1.2.7.1INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentSwitchConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.248.15.1.2.8
hmAgentSwitchBroadcastControlMode
OBJECT-TYPE
The switch config broadcast allows you to enable or disable broadcast storm recovery mode. When you specify Enable for Broadcast Storm Recovery and the broadcast traffic on any Ethernet port exceeds 20 percent of the link speed, the switch blocks (discards) the broadcast traffic until the broadcast traffic returns to 10 percent or less. Upper limit for 10M link is 20% and lower limit is 10%. For 100M link Upper limit is 5% and lower limit is 2%
1.3.6.1.4.1.248.15.1.2.8.2INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentSwitchDot3FlowControlMode
OBJECT-TYPE
Config switchconfig flowcontrol allows you to enable or disable 802.3x flow control for the switch. This value applies to only full-duplex mode ports.
1.3.6.1.4.1.248.15.1.2.8.3INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentSwitchAddressAgingTimeoutTable
OBJECT-TYPE
The switch's address aging timeout table
1.3.6.1.4.1.248.15.1.2.8.4not-accessiblecurrent
hmAgentSwitchAddressAgingTimeoutEntry
OBJECT-TYPE
Aging information about a specific Filtering Database.
1.3.6.1.4.1.248.15.1.2.8.4.1not-accessiblecurrent
hmAgentSwitchAddressAgingTimeout
OBJECT-TYPE
The FDB entry's address aging timeout (in seconds)
1.3.6.1.4.1.248.15.1.2.8.4.1.1Integer32 (10..1000000)read-writecurrent
hmAgentSwitchStaticMacFilteringTable
OBJECT-TYPE
The switch's static Mac filtering table
1.3.6.1.4.1.248.15.1.2.8.5not-accessiblecurrent
hmAgentSwitchStaticMacFilteringEntry
OBJECT-TYPE
Per-port ingress/egress filter configuration based on VLAN Id and MAC address.
1.3.6.1.4.1.248.15.1.2.8.5.1not-accessiblecurrent
hmAgentSwitchStaticMacFilteringVlanId
OBJECT-TYPE
The Static MAC Filter Vlan Id
1.3.6.1.4.1.248.15.1.2.8.5.1.1Integer32read-onlycurrent
hmAgentSwitchStaticMacFilteringAddress
OBJECT-TYPE
The Static MAC Filter MAC address
1.3.6.1.4.1.248.15.1.2.8.5.1.2MacAddressread-onlycurrent
hmAgentSwitchStaticMacFilteringSourcePortMask
OBJECT-TYPE
The Static MAC Filter source port mask. When setting this value, the system will ignore configuration for ports not between the first and last valid ports. Configuration of any port numbers between this range that are not valid ports return a failure message, but will still apply configuration for valid ports. To obtain port numbers from interface numbers, use the objects hmAgentPortDot1dBasePort and hmAgentPortIfIndex in the hmAgentPortConfigTable table.
1.3.6.1.4.1.248.15.1.2.8.5.1.3HmAgentPortMaskread-writecurrent
hmAgentSwitchStaticMacFilteringDestPortMask
OBJECT-TYPE
The Static MAC Filter destination port mask. When setting this value, the system will ignore configuration for ports not between the first and last valid ports. Configuration of any port numbers between this range that are not valid ports return a failure message, but will still apply configuration for valid ports. To obtain port numbers from interface numbers, use the objects hmAgentPortDot1dBasePort and hmAgentPortIfIndex in the hmAgentPortConfigTable table.
1.3.6.1.4.1.248.15.1.2.8.5.1.4HmAgentPortMaskread-writecurrent
hmAgentSwitchStaticMacFilteringStatus
OBJECT-TYPE
The Static MAC Filter status. Supported values: active(1) - valid entry createAndGo(4) - used to create a new entry destroy(6) - removes the entry
1.3.6.1.4.1.248.15.1.2.8.5.1.5RowStatusread-createcurrent
hmAgentSwitchIGMPSnoopingGroup
OBJECT-IDENTITY
1.3.6.1.4.1.248.15.1.2.8.6
hmAgentSwitchIGMPSnoopingAdminMode
OBJECT-TYPE
This enables or disables IGMP Snooping on the system.
1.3.6.1.4.1.248.15.1.2.8.6.1INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentSwitchIGMPSnoopingGroupMembershipInterval
OBJECT-TYPE
The amount of time in seconds a switch will wait for a report for a particular group on a particular interface before it deletes the interface from the entry.
1.3.6.1.4.1.248.15.1.2.8.6.2Integer32 (3..3600)read-writecurrent
hmAgentSwitchIGMPSnoopingMaxResponseTime
OBJECT-TYPE
The amount of time in seconds a switch will wait after sending a query on an interface because it did not receive a report for a particular group in that interface. This value must be less than hmAgentSwitchIGMPSnoopingQueryInterval.
1.3.6.1.4.1.248.15.1.2.8.6.3Integer32 (1..3598)read-writecurrent
hmAgentSwitchIGMPSnoopingMRPExpirationTime
OBJECT-TYPE
Multicast Router Present Expiration Time. The amount of time in seconds a switch will wait for a query to be received on an interface before the interface is removed from the list of interfaces with mutlticast routers attached. A value of zero indicates an infinite timeout, i.e. the entries in the list will not expire.
1.3.6.1.4.1.248.15.1.2.8.6.4Integer32 (0..3600)read-writecurrent
hmAgentSwitchIGMPSnoopingPortMask
OBJECT-TYPE
IGMP Snooping Port Mask. This allows configuration of IGMP Snooping on selected ports. IGMP Snooping cannot be enabled on an interface that has routing enabled, or is a member of a LAG. If a port which has IGMP Snooping enabled becomes enabled for routing, or is enlisted as a member of a LAG, IGMP Snooping functionality will be disabled on that port. IGMP Snooping functionality will be subsequently be reenabled if routing is disabled or LAG membership is removed from an interface that had previously had IGMP Snooping enabled. To obtain port numbers from interface numbers, use the objects hmAgentPortDot1dBasePort and hmAgentPortIfIndex in the hmAgentPortConfigTable table.
1.3.6.1.4.1.248.15.1.2.8.6.5HmAgentPortMaskread-writecurrent
hmAgentSwitchIGMPSnoopingMulticastControlFramesProcessed
OBJECT-TYPE
Multicast Control Frames Processed by CPU. The number of multicast control frames that have been processed by the CPU.
1.3.6.1.4.1.248.15.1.2.8.6.6Counter32read-onlycurrent
hmAgentSwitchMFDBGroup
OBJECT-IDENTITY
1.3.6.1.4.1.248.15.1.2.8.7
hmAgentSwitchMFDBTable
OBJECT-TYPE
The Multicast Forwarding Database table
1.3.6.1.4.1.248.15.1.2.8.7.1not-accessiblecurrent
hmAgentSwitchMFDBEntry
OBJECT-TYPE
Contains Forwarding and Filtering information per Vlan Index, MAC Address, and Component User.
1.3.6.1.4.1.248.15.1.2.8.7.1.1not-accessiblecurrent
hmAgentSwitchMFDBVlanId
OBJECT-TYPE
Vlan Index for which this entry is associated with.
1.3.6.1.4.1.248.15.1.2.8.7.1.1.1VlanIndexread-onlycurrent
hmAgentSwitchMFDBMacAddress
OBJECT-TYPE
A multicast MAC address for which the switch has forwarding and or filtering information.
1.3.6.1.4.1.248.15.1.2.8.7.1.1.2MacAddressread-onlycurrent
hmAgentSwitchMFDBProtocolType
OBJECT-TYPE
The component that is responsible for this entry in the Multicast Forwarding Database.
1.3.6.1.4.1.248.15.1.2.8.7.1.1.3INTEGER {static(1), gmrp(2), igmp(3), msd(4)}read-onlycurrent
hmAgentSwitchMFDBType
OBJECT-TYPE
This displays the type of the entry. static(1) - Entries configured by the end user dynamic(2) - Entries added as a result of a learning process or protocol
1.3.6.1.4.1.248.15.1.2.8.7.1.1.4INTEGER {static(1), dynamic(2)}read-onlycurrent
hmAgentSwitchMFDBDescription
OBJECT-TYPE
Text description of this multicast table entry.
1.3.6.1.4.1.248.15.1.2.8.7.1.1.5DisplayStringread-onlycurrent
hmAgentSwitchMFDBForwardingPortMask
OBJECT-TYPE
BitMask indicating which ports this entry indicates should be forwarded. To obtain port numbers from interface numbers, use the objects hmAgentPortDot1dBasePort and hmAgentPortIfIndex in the hmAgentPortConfigTable table.
1.3.6.1.4.1.248.15.1.2.8.7.1.1.6HmAgentPortMaskread-onlycurrent
hmAgentSwitchMFDBFilteringPortMask
OBJECT-TYPE
BitMask indicating which ports this entry indicates should be filtered. To obtain port numbers from interface numbers, use the objects hmAgentPortDot1dBasePort and hmAgentPortIfIndex in the hmAgentPortConfigTable table.
1.3.6.1.4.1.248.15.1.2.8.7.1.1.7HmAgentPortMaskread-onlycurrent
hmAgentSwitchMFDBSummaryTable
OBJECT-TYPE
The Multicast Forwarding Database Summary table
1.3.6.1.4.1.248.15.1.2.8.7.2not-accessiblecurrent
hmAgentSwitchMFDBSummaryEntry
OBJECT-TYPE
Summarizes the forwarding ports for all components registered for all MFDB table entries with the same Vlan Index and MAC Address.
1.3.6.1.4.1.248.15.1.2.8.7.2.1not-accessiblecurrent
hmAgentSwitchMFDBSummaryVlanId
OBJECT-TYPE
Vlan Index for which this entry is associated with.
1.3.6.1.4.1.248.15.1.2.8.7.2.1.1VlanIndexread-onlycurrent
hmAgentSwitchMFDBSummaryMacAddress
OBJECT-TYPE
A multicast MAC address for which the switch has forwarding and or filtering information.
1.3.6.1.4.1.248.15.1.2.8.7.2.1.2MacAddressread-onlycurrent
hmAgentSwitchMFDBSummaryForwardingPortMask
OBJECT-TYPE
Port Mask indicating which ports this entry indicates should be forwarded. To obtain port numbers from interface numbers, use the objects hmAgentPortDot1dBasePort and hmAgentPortIfIndex in the hmAgentPortConfigTable table.
1.3.6.1.4.1.248.15.1.2.8.7.2.1.3HmAgentPortMaskread-onlycurrent
hmAgentSwitchMFDBMaxTableEntries
OBJECT-TYPE
This displays the maximum number of entries that can possibly be in the Multicast Forwarding Database table.
1.3.6.1.4.1.248.15.1.2.8.7.3Gauge32read-onlycurrent
hmAgentSwitchMFDBMostEntriesUsed
OBJECT-TYPE
This displays the largest number of entries that have been present in the Multicast Forwarding Database table. This value is also known as the MFDB high-water mark.
1.3.6.1.4.1.248.15.1.2.8.7.4Gauge32read-onlycurrent
hmAgentSwitchMFDBCurrentEntries
OBJECT-TYPE
This displays the current number of entries in the Multicast Forwarding Database table.
1.3.6.1.4.1.248.15.1.2.8.7.5Gauge32read-onlycurrent
hmAgentSwitchDVlanTagGroup
OBJECT-IDENTITY
1.3.6.1.4.1.248.15.1.2.8.8
hmAgentSwitchDVlanTagEthertype
OBJECT-TYPE
Configures the Double Vlan Tag Ethertype for the switch. If this object is supported, ethertype cannot be configured per port. Commonly used are the Ethertypes for vman tags (34984, or 0x88A8) and dot1q tags (33024, or 0x8100).
1.3.6.1.4.1.248.15.1.2.8.8.1Integer32 (0..65535)read-writecurrent
hmAgentSwitchVoiceVLANGroup
OBJECT-IDENTITY
1.3.6.1.4.1.248.15.1.2.8.25
hmAgentSwitchVoiceVLANAdminMode
OBJECT-TYPE
This enables or disables Voice VLAN on the system.
1.3.6.1.4.1.248.15.1.2.8.25.1INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentSwitchVoiceVlanDeviceTable
OBJECT-TYPE
A table of the Voice Vlan device entries.
1.3.6.1.4.1.248.15.1.2.8.25.2not-accessiblecurrent
hmAgentSwitchVoiceVlanDeviceEntry
OBJECT-TYPE
Represents entry for a Voice Device on the interface.
1.3.6.1.4.1.248.15.1.2.8.25.2.1not-accessiblecurrent
hmAgentSwitchVoiceVlanInterfaceNum
OBJECT-TYPE
The interface number of this interface.
1.3.6.1.4.1.248.15.1.2.8.25.2.1.1Integer32 (1..65535)read-onlycurrent
hmAgentSwitchVoiceVlanDeviceMacAddress
OBJECT-TYPE
The Voice Device Mac address
1.3.6.1.4.1.248.15.1.2.8.25.2.1.2MacAddressread-onlycurrent
hmAgentTransferConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.248.15.1.2.9
hmAgentTransferUploadGroup
OBJECT-IDENTITY
1.3.6.1.4.1.248.15.1.2.9.1
hmAgentTransferUploadMode
OBJECT-TYPE
Transfer upload mode configures the mode to use when uploading from the switch. The mode is either X/Y/ZMODEM or TFTP. X/Y/ZMODEM is valid only when the file transfer is initiated by the serial EIA 232 port.
1.3.6.1.4.1.248.15.1.2.9.1.1INTEGER {tftp(1), xmodem(2), ymodem(3), zmodem(4)}read-writecurrent
hmAgentTransferUploadServerIP
OBJECT-TYPE
Transfer upload tftpserverip configures the IP address of the server where the file is located. It is valid only when the Transfer Mode is TFTP. The address is 4 integer bytes ranging from 0 to 255.
1.3.6.1.4.1.248.15.1.2.9.1.2IpAddressread-writecurrent
hmAgentTransferUploadPath
OBJECT-TYPE
Transfer upload tftppath configures the directory path where the file is to be uploaded to. The switch remembers the last file path used.
1.3.6.1.4.1.248.15.1.2.9.1.3DisplayString (SIZE(0..31))read-writecurrent
hmAgentTransferUploadFilename
OBJECT-TYPE
Transfer upload tftpfilename configures the file name for the file being uploaded from the switch. It can be up to 32 alphanumeric characters. The switch remembers the last file name used. File path can be appended to the file name if the string is less than 17 characters. Otherwise, the File Path field will need to be used and the File Name will be appended to the File Path as is. An example would be File Path set to c:/tftp/code/ and File Name set to e1r1v1.opr. Note: File Name, File Path, and TFTP Server IP Address are applicable only if the Transfer Mode is TFTP.
1.3.6.1.4.1.248.15.1.2.9.1.4DisplayString (SIZE(0..31))read-writecurrent
hmAgentTransferUploadDataType
OBJECT-TYPE
Transfer upload datatype configures the type of file to upload from the switch. The types for upload are: - Configuration File - Error log - Message log - Trap log
1.3.6.1.4.1.248.15.1.2.9.1.5INTEGER {config(2), errorlog(3), messagelog(4), traplog(5), clibanner(6)}read-writecurrent
hmAgentTransferUploadStart
OBJECT-TYPE
Transfer upload start will start an upload transfer. The hmAgentTransferUploadMode object must not be set to xmodem(2), ymodem(3), or zmodem(4) to initiate a transfer via SNMP.
1.3.6.1.4.1.248.15.1.2.9.1.6INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentTransferUploadStatus
OBJECT-TYPE
Indicates the current status of an upload transfer.
1.3.6.1.4.1.248.15.1.2.9.1.7INTEGER {notInitiated(1), transferStarting(2), errorStarting(3), wrongFileType(4), updatingConfig(5), invalidConfigFile(6), writingToFlash(7), failureWritingToFlash(8), checkingCRC(9), failedCRC(10), unknownDirection(11), transferSuccessful(12), transferFailed(13)}read-onlycurrent
hmAgentTransferDownloadGroup
OBJECT-IDENTITY
1.3.6.1.4.1.248.15.1.2.9.2
hmAgentTransferDownloadMode
OBJECT-TYPE
Transfer download mode configures the mode to use when downloading to the switch. The mode is either X/Y/ZMODEM or TFTP. X/Y/ZMODEM is valid only when the file transfer is initiated by the serial EIA 232 port.
1.3.6.1.4.1.248.15.1.2.9.2.1INTEGER {tftp(1), xmodem(2), ymodem(3), zmodem(4)}read-writecurrent
hmAgentTransferDownloadServerIP
OBJECT-TYPE
Transfer download tftpserverip configures the IP address of the server where the file is located. It is valid only when the Transfer Mode is TFTP. The address is 4 integer bytes ranging from 0 to 255.
1.3.6.1.4.1.248.15.1.2.9.2.2IpAddressread-writecurrent
hmAgentTransferDownloadPath
OBJECT-TYPE
Transfer download tftppath configures the directory path where the file is located. The switch remembers the last file path used.
1.3.6.1.4.1.248.15.1.2.9.2.3DisplayString (SIZE(0..31))read-writecurrent
hmAgentTransferDownloadFilename
OBJECT-TYPE
Transfer download tftpfilename configures the file name for the file being downloaded to the switch. It can be up to 32 alphanumeric characters. The switch remembers the last file name used. File path can be appended to the file name if the string is less than 33 characters. Otherwise, the File Path field will need to be used and the File Name will be appended to the File Path as is. An example would be File Path set to c:/tftp/code/ and File Name set to e1r1v1.opr. Note: File Name, File Path, and TFTP Server IP Address are applicable only if the Transfer Mode is TFTP.
1.3.6.1.4.1.248.15.1.2.9.2.4DisplayString (SIZE(0..31))read-writecurrent
hmAgentTransferDownloadDataType
OBJECT-TYPE
Transfer download datatype configures the type of file to download to the switch. The types for download are: code - Code File config - Configuration File
1.3.6.1.4.1.248.15.1.2.9.2.5INTEGER {code(2), config(3), sshkey-rsa1(4), sshkey-rsa2(5), sshkey-dsa(6), sslpem-root(7), sslpem-server(8), sslpem-dhweak(9), sslpem-dhstrong(10), clibanner(11)}read-writecurrent
hmAgentTransferDownloadStart
OBJECT-TYPE
Transfer download start will start an download transfer. The hmAgentTransferDownloadMode object must not be set to xmodem(2), ymodem(3), or zmodem(4) to initiate a transfer via SNMP.
1.3.6.1.4.1.248.15.1.2.9.2.6INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentTransferDownloadStatus
OBJECT-TYPE
Indicates the current status of an download transfer.
1.3.6.1.4.1.248.15.1.2.9.2.7INTEGER {notInitiated(1), transferStarting(2), errorStarting(3), wrongFileType(4), updatingConfig(5), invalidConfigFile(6), writingToFlash(7), failureWritingToFlash(8), checkingCRC(9), failedCRC(10), unknownDirection(11), transferSuccessful(12), transferFailed(13)}read-onlycurrent
hmAgentPortMirroringGroup
OBJECT-IDENTITY
1.3.6.1.4.1.248.15.1.2.10
hmAgentMirroredPortIfIndex
OBJECT-TYPE
IfIndex of the mirrored port
1.3.6.1.4.1.248.15.1.2.10.1Integer32read-writeobsolete
hmAgentProbePortIfIndex
OBJECT-TYPE
IfIndex of the probe port
1.3.6.1.4.1.248.15.1.2.10.2Integer32read-writeobsolete
hmAgentPortMirroringMode
OBJECT-TYPE
Port mirroring mode: enable - enable mirroring mode disable - disable mirroring mode delete - clear MirroredPort and Probe Port configuration
1.3.6.1.4.1.248.15.1.2.10.3INTEGER {enable(1), disable(2), delete(3)}read-writeobsolete
hmAgentPortMirrorTable
OBJECT-TYPE
This table includes entries for each Port Mirroring session.
1.3.6.1.4.1.248.15.1.2.10.4not-accessiblecurrent
hmAgentPortMirrorEntry
OBJECT-TYPE
Provides configuration of a Port Mirroring session specifying the destination port, and the source Port Mask, providing a many-to-one mapping.
1.3.6.1.4.1.248.15.1.2.10.4.1not-accessiblecurrent
hmAgentPortMirrorSessionNum
OBJECT-TYPE
The Session number of this mirroring entry. The number of sessions is fixed, and is platform dependant.
1.3.6.1.4.1.248.15.1.2.10.4.1.1Unsigned32not-accessiblecurrent
hmAgentPortMirrorDestinationPort
OBJECT-TYPE
The port which traffic from the mirrored ports will be sent to.
1.3.6.1.4.1.248.15.1.2.10.4.1.2Unsigned32read-writecurrent
hmAgentPortMirrorSourcePortMask
OBJECT-TYPE
The ports from which traffic will be sent to the destination port. The destination port can not be included in this list of ports.
1.3.6.1.4.1.248.15.1.2.10.4.1.3HmAgentPortMaskread-writecurrent
hmAgentPortMirrorAdminMode
OBJECT-TYPE
The status of this port mirroring session. enable(1) - This session is active and all traffic from the source ports will be mirrored to the destination port. disable(2) - This session is not active. delete(3) - Remove the configuration for this Session
1.3.6.1.4.1.248.15.1.2.10.4.1.4INTEGER {enable(1), disable(2), delete(3)}read-writecurrent
hmAgentPortMirrorIngressMask
OBJECT-TYPE
The ports from which ingress traffic will be mirrored.
1.3.6.1.4.1.248.15.1.2.10.4.1.248HmAgentPortMaskread-writecurrent
hmAgentPortMirrorEgressMask
OBJECT-TYPE
The ports from which egress traffic will be mirrored.
1.3.6.1.4.1.248.15.1.2.10.4.1.249HmAgentPortMaskread-writecurrent
hmAgentDot3adAggPortTable
OBJECT-TYPE
This table provides 802.3ad link aggregation information for each physical port that is not available through the standard MIB.
1.3.6.1.4.1.248.15.1.2.12not-accessiblecurrent
hmAgentDot3adAggPortEntry
OBJECT-TYPE
Information about a table entry. The hmAgentDot3adAggPort identifies the external interface number of the port.
1.3.6.1.4.1.248.15.1.2.12.1not-accessiblecurrent
hmAgentDot3adAggPort
OBJECT-TYPE
ifIndex of this physical port
1.3.6.1.4.1.248.15.1.2.12.1.1Integer32read-onlycurrent
hmAgentDot3adAggPortLACPMode
OBJECT-TYPE
Enable/disable 802.3ad LACP on this port
1.3.6.1.4.1.248.15.1.2.12.1.2INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentPortConfigTable
OBJECT-TYPE
A table of the switch's physical port config entries
1.3.6.1.4.1.248.15.1.2.13not-accessiblecurrent
hmAgentPortConfigEntry
OBJECT-TYPE
Switch's physical port config entry
1.3.6.1.4.1.248.15.1.2.13.1not-accessiblecurrent
hmAgentPortDot1dBasePort
OBJECT-TYPE
The port number of this port.
1.3.6.1.4.1.248.15.1.2.13.1.1Integer32 (1..65535)read-onlycurrent
hmAgentPortIfIndex
OBJECT-TYPE
The switch's Port IfIndex
1.3.6.1.4.1.248.15.1.2.13.1.2Integer32read-onlycurrent
hmAgentPortIanaType
OBJECT-TYPE
The switch's Port Type
1.3.6.1.4.1.248.15.1.2.13.1.3IANAifTyperead-onlycurrent
hmAgentPortSTPMode
OBJECT-TYPE
The switch's Port Spanning Tree Protocol Mode STP mode values are: dot1d (the default) fast, indicates you want to use the fast spanning tree mode off, indicates the STP mode is turned off for a particular port This object is only supported when the Dot1d Protocol is enabled.
1.3.6.1.4.1.248.15.1.2.13.1.4INTEGER {dot1d(1), fast(2), off(3)}read-writecurrent
hmAgentPortSTPState
OBJECT-TYPE
The switch's Port Spanning Tree Protocol State. This object is only supported when the Dot1d Protocol is enabled.
1.3.6.1.4.1.248.15.1.2.13.1.5INTEGER {blocking(1), listening(2), learning(3), forwarding(4), disabled(5)}read-onlycurrent
hmAgentPortAdminMode
OBJECT-TYPE
The switch's Port Admin Mode
1.3.6.1.4.1.248.15.1.2.13.1.6INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentPortPhysicalMode
OBJECT-TYPE
The switch's Port Speed Mode. This is the configured physical mode. This object is read-only for gigabit ports
1.3.6.1.4.1.248.15.1.2.13.1.7INTEGER {auto-negotiate(1), half-10(2), full-10(3), half-100(4), full-100(5), half-100fx(6), full-100fx(7), full-1000sx(8)}read-writeobsolete
hmAgentPortPhysicalStatus
OBJECT-TYPE
The switch's Port Physical Speed Status. This is the current actual speed.
1.3.6.1.4.1.248.15.1.2.13.1.8INTEGER {auto-negotiate(1), half-10(2), full-10(3), half-100(4), full-100(5), half-100fx(6), full-100fx(7), full-1000sx(8)}read-onlyobsolete
hmAgentPortLinkTrapMode
OBJECT-TYPE
If enabled, link up and link down traps will be sent for this port.
1.3.6.1.4.1.248.15.1.2.13.1.9INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentPortClearStats
OBJECT-TYPE
clear stats for this port only
1.3.6.1.4.1.248.15.1.2.13.1.10INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentPortDefaultType
OBJECT-TYPE
This object identifies the default administrative port type, to be used in conjunction with the operational port type denoted by hmAgentPortType. The set of possible values for this object is the same as the set defined for the hmAgentPortType object. This object represents the administratively-configured type of the MAU. If auto-negotiation is not enabled or is not implemented for this MAU, the value of this object determines the operational type of the MAU. In this case, a set to this object will force the MAU into the specified operating mode. If auto-negotiation is implemented and enabled for this MAU, the operational type of the MAU is determined by auto-negotiation, and the value of this object denotes the type to which the MAU will automatically revert if/when auto-negotiation is later disabled. The valid values for this object are: dot3MauType10BaseTHD dot3MauType10BaseTFD dot3MauType100BaseTXHD dot3MauType100BaseTXFD dot3MauType100BaseFXFD dot3MauType1000BaseSXFD
1.3.6.1.4.1.248.15.1.2.13.1.11OBJECT IDENTIFIERread-writecurrent
hmAgentPortType
OBJECT-TYPE
This object identifies the port type. An initial set of MAU types are defined in RFC 2668. The assignment of OBJECT IDENTIFIERs to new types of MAUs is managed by the IANA. If the MAU type is unknown, the object identifier unknownMauType OBJECT IDENTIFIER ::= { 0 0 } is returned. Note that unknownMauType is a syntactically valid object identifier, and any conformant implementation of ASN.1 and the BER must be able to generate and recognize this value. This object represents the operational type of the MAU, as determined by either (1) the result of the auto-negotiation function or (2) if auto-negotiation is not enabled or is not implemented for this MAU, by the value of the object hmAgentPortDefaultType, or (3) for the GigE card a value determined by the GBIC connected to the card. In case (2), a set to the object hmAgentPortDefaultType will force the MAU into the new operating mode. The valid values for this object are: dot3MauType10BaseTHD dot3MauType10BaseTFD dot3MauType100BaseTXHD dot3MauType100BaseTXFD dot3MauType100BaseFXFD dot3MauType1000BaseSXFD dot3MauType1000BaseTFD
1.3.6.1.4.1.248.15.1.2.13.1.12OBJECT IDENTIFIERread-onlycurrent
hmAgentPortAutoNegAdminStatus
OBJECT-TYPE
This object identifies the administration status of auto negotiation for this port.
1.3.6.1.4.1.248.15.1.2.13.1.13INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentPortDot3FlowControlMode
OBJECT-TYPE
Config flowcontrol allows you to enable or disable 802.3x flow control for this port. This value applies to only full-duplex mode ports.
1.3.6.1.4.1.248.15.1.2.13.1.14INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentPortDVlanTagMode
OBJECT-TYPE
Controls the Double Vlan Tag mode on this port. Default is normal(2).
1.3.6.1.4.1.248.15.1.2.13.1.15INTEGER {core(1), normal(2), access(3)}read-writecurrent
hmAgentPortDVlanTagEthertype
OBJECT-TYPE
Configures the Double Vlan Tag Ethertype for this port. If this object is supported, ethertype cannot be configured globally for the switch. Commonly used are the Ethertypes for vman tags (34984, or 0x88A8) and dot1q tags (33024, or 0x8100).
1.3.6.1.4.1.248.15.1.2.13.1.16Integer32 (0..65535)read-writecurrent
hmAgentPortDVlanTagCustomerId
OBJECT-TYPE
Configures the Customer ID for the Double Vlan Tag for this port.
1.3.6.1.4.1.248.15.1.2.13.1.17Integer32read-writecurrent
hmAgentPortMaxFrameSizeLimit
OBJECT-TYPE
This object identifies the largest value that can be configured for hmAgentPortMaxFrameSize
1.3.6.1.4.1.248.15.1.2.13.1.18Integer32read-onlycurrent
hmAgentPortMaxFrameSize
OBJECT-TYPE
This object identifies the currently configured maximum frame size value for this port. The maximmum value that this object can be set to is the value of hmAgentPortMaxFrameSizeLimit. For Ethernet ports which support 802.1Q vlan tagging, the minimum value that this object can be set to is 1522
1.3.6.1.4.1.248.15.1.2.13.1.19Integer32read-writecurrent
hmAgentPortVoiceVlanMode
OBJECT-TYPE
Describes and Configures the Port Voice VLAN Mode.
1.3.6.1.4.1.248.15.1.2.13.1.20INTEGER {none(1), vlanid(2), dot1p(3), vlanidanddot1p(4), untagged(5), disable(6)}read-writecurrent
hmAgentPortVoiceVlanID
OBJECT-TYPE
Describes and Configures the Port Voice VLAN ID if the Voice Vlan Mode is Vlan ID.
1.3.6.1.4.1.248.15.1.2.13.1.21Integer32 (0..4093)read-writecurrent
hmAgentPortVoiceVlanPriority
OBJECT-TYPE
Describes and Configures the Port Voice VLAN Priority if the Voice Vlan Mode is dot1p. A value of 255 indicates that the priority is not configured.
1.3.6.1.4.1.248.15.1.2.13.1.22INTEGER (0..7 | 255)read-writecurrent
hmAgentPortVoiceVlanDataPriorityMode
OBJECT-TYPE
Describes and Configures the Port Voice VLAN Data Priority Mode.
1.3.6.1.4.1.248.15.1.2.13.1.23INTEGER {trust(1), untrust(2)}read-writecurrent
hmAgentPortVoiceVlanOperationalStatus
OBJECT-TYPE
Describes the Port Voice VLAN Operational Status.
1.3.6.1.4.1.248.15.1.2.13.1.24INTEGER {enabled(1), disabled(2)}read-onlycurrent
hmAgentPortVoiceVlanDSCP
OBJECT-TYPE
Describes and Configures the Port Voice VLAN DSCP value.
1.3.6.1.4.1.248.15.1.2.13.1.25Integer32read-writecurrent
hmAgentPortVoiceVlanAuthMode
OBJECT-TYPE
Describes and Configures the Port Voice VLAN Authentication mode. Disable means authentication not required for voice devices when dot1x is enabled.
1.3.6.1.4.1.248.15.1.2.13.1.26INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentProtocolConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.248.15.1.2.14
hmAgentProtocolGroupCreate
OBJECT-TYPE
Set to non-empty string to create a Protocol-Based VLAN group.
1.3.6.1.4.1.248.15.1.2.14.1DisplayString (SIZE(1..16))read-writecurrent
hmAgentProtocolGroupTable
OBJECT-TYPE
A table of the switch's Protocol-based VLAN entries
1.3.6.1.4.1.248.15.1.2.14.2not-accessiblecurrent
hmAgentProtocolGroupEntry
OBJECT-TYPE
Switch's Protocol-based VLAN entry
1.3.6.1.4.1.248.15.1.2.14.2.1not-accessiblecurrent
hmAgentProtocolGroupId
OBJECT-TYPE
Group identifier of the Protocol-based VLAN entry.
1.3.6.1.4.1.248.15.1.2.14.2.1.1Integer32read-onlycurrent
hmAgentProtocolGroupName
OBJECT-TYPE
Group name of the Protocol-based VLAN entry.
1.3.6.1.4.1.248.15.1.2.14.2.1.2DisplayStringread-onlycurrent
hmAgentProtocolGroupVlanId
OBJECT-TYPE
VLAN associated with the Protocol-based VLAN entry. Set to 0 to remove.
1.3.6.1.4.1.248.15.1.2.14.2.1.3Integer32read-writecurrent
hmAgentProtocolGroupProtocolIP
OBJECT-TYPE
The status of the IP protocol association with the Protocol-based VLAN entry.
1.3.6.1.4.1.248.15.1.2.14.2.1.4INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentProtocolGroupProtocolARP
OBJECT-TYPE
The status of the ARP protocol association with the Protocol-based VLAN entry.
1.3.6.1.4.1.248.15.1.2.14.2.1.5INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentProtocolGroupProtocolIPX
OBJECT-TYPE
The status of the IPX protocol association with the Protocol-based VLAN entry.
1.3.6.1.4.1.248.15.1.2.14.2.1.6INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentProtocolGroupStatus
OBJECT-TYPE
The status of the Protocol-based VLAN entry. active(1) - this entry is active destroy(6) - remove this entry
1.3.6.1.4.1.248.15.1.2.14.2.1.7RowStatusread-writecurrent
hmAgentProtocolGroupPortTable
OBJECT-TYPE
A table of the switch's physical port config entries
1.3.6.1.4.1.248.15.1.2.14.3not-accessiblecurrent
hmAgentProtocolGroupPortEntry
OBJECT-TYPE
Switch's physical port config entry
1.3.6.1.4.1.248.15.1.2.14.3.1not-accessiblecurrent
hmAgentProtocolGroupPortIfIndex
OBJECT-TYPE
The interface number of this instance.
1.3.6.1.4.1.248.15.1.2.14.3.1.1Integer32read-onlycurrent
hmAgentProtocolGroupPortStatus
OBJECT-TYPE
The status of this entry. active(1) - the port is associated with this group createAndGo(4) - add the port to this group createAndWait(5) - add the port to this group destroy(6) - remove the port from this group
1.3.6.1.4.1.248.15.1.2.14.3.1.2RowStatusread-createcurrent
hmAgentStpSwitchConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.248.15.1.2.15
hmAgentStpConfigDigestKey
OBJECT-TYPE
The MST configuration digest key.
1.3.6.1.4.1.248.15.1.2.15.1OCTET STRING (SIZE(16))read-onlycurrent
hmAgentStpConfigFormatSelector
OBJECT-TYPE
The MST configuration format selector. A value other than 0 (zero) indicates non-support for the IEEE 802.1s standard.
1.3.6.1.4.1.248.15.1.2.15.2Unsigned32 (0..255)read-onlycurrent
hmAgentStpConfigName
OBJECT-TYPE
The MST configuration name of at most 32 characters.
1.3.6.1.4.1.248.15.1.2.15.3DisplayString (SIZE(1..32))read-writecurrent
hmAgentStpConfigRevision
OBJECT-TYPE
The MST configuration revision. The default value is 1.
1.3.6.1.4.1.248.15.1.2.15.4Unsigned32 (0..65535)read-writecurrent
hmAgentStpForceVersion
OBJECT-TYPE
The MST configuration force protocol version. The default version is dot1w.
1.3.6.1.4.1.248.15.1.2.15.5INTEGER {dot1d(1), dot1w(2), dot1s(3)}read-writecurrent
hmAgentStpAdminMode
OBJECT-TYPE
The spanning tree operational status. enable(1) - enables spanning tree operational status on the switch. disable(2) - disables spanning tree operational status on the switch. The default status is enabled.
1.3.6.1.4.1.248.15.1.2.15.6INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentStpPortTable
OBJECT-TYPE
STP port table.
1.3.6.1.4.1.248.15.1.2.15.7not-accessiblecurrent
hmAgentStpPortEntry
OBJECT-TYPE
STP port entry.
1.3.6.1.4.1.248.15.1.2.15.7.1not-accessiblecurrent
hmAgentStpPortState
OBJECT-TYPE
The administrative STP state for the port. enable(1) - enables STP on the port. disable(2) - disables STP on the port. The default port STP state is enabled for the first 4095 ports and disabled for any ports beyond.
1.3.6.1.4.1.248.15.1.2.15.7.1.1INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentStpPortStatsMstpBpduRx
OBJECT-TYPE
The MSTP BPDUs received on a specific port.
1.3.6.1.4.1.248.15.1.2.15.7.1.2Counter32read-onlycurrent
hmAgentStpPortStatsMstpBpduTx
OBJECT-TYPE
The MSTP BPDUs sent from a specific port.
1.3.6.1.4.1.248.15.1.2.15.7.1.3Counter32read-onlycurrent
hmAgentStpPortStatsRstpBpduRx
OBJECT-TYPE
The RSTP BPDUs received on a specific port.
1.3.6.1.4.1.248.15.1.2.15.7.1.4Counter32read-onlycurrent
hmAgentStpPortStatsRstpBpduTx
OBJECT-TYPE
The RSTP BPDUs sent from a specific port.
1.3.6.1.4.1.248.15.1.2.15.7.1.5Counter32read-onlycurrent
hmAgentStpPortStatsStpBpduRx
OBJECT-TYPE
The STP BPDUs received on a specific port.
1.3.6.1.4.1.248.15.1.2.15.7.1.6Counter32read-onlycurrent
hmAgentStpPortStatsStpBpduTx
OBJECT-TYPE
The STP BPDUs sent from a specific port.
1.3.6.1.4.1.248.15.1.2.15.7.1.7Counter32read-onlycurrent
hmAgentStpPortUpTime
OBJECT-TYPE
Time since port was reset. It is displayed in days, hours, minutes, and seconds.
1.3.6.1.4.1.248.15.1.2.15.7.1.8TimeTicksread-onlycurrent
hmAgentStpPortMigrationCheck
OBJECT-TYPE
Force the specified port to transmit RSTP or MSTP BPDU's. Supported values: false(0) - BPDUs are not to be transmitted. true(1) - BPDUs are to be transmitted A non-zero value indicates that BPDUs are to be sent on the specified port.
1.3.6.1.4.1.248.15.1.2.15.7.1.9INTEGER {false(0), true(1)}read-writecurrent
hmAgentStpPortHelloTime
OBJECT-TYPE
Hello time for the STP port. The default value is 2.
1.3.6.1.4.1.248.15.1.2.15.7.1.10Unsigned32 (1..2)read-writecurrent
hmAgentStpCstConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.248.15.1.2.15.8
hmAgentStpCstHelloTime
OBJECT-TYPE
The MSTP root port hello time for the CIST.
1.3.6.1.4.1.248.15.1.2.15.8.1Unsigned32read-onlycurrent
hmAgentStpCstMaxAge
OBJECT-TYPE
The MSTP root port max age for the CIST.
1.3.6.1.4.1.248.15.1.2.15.8.2Unsigned32read-onlycurrent
hmAgentStpCstRegionalRootId
OBJECT-TYPE
The MSTP regional root identifier for the CIST.
1.3.6.1.4.1.248.15.1.2.15.8.3OCTET STRING (SIZE(8))read-onlycurrent
hmAgentStpCstRegionalRootPathCost
OBJECT-TYPE
The MSTP regional root path cost for the CIST.
1.3.6.1.4.1.248.15.1.2.15.8.4Unsigned32read-onlycurrent
hmAgentStpCstRootFwdDelay
OBJECT-TYPE
The MSTP root port forward delay for the CIST.
1.3.6.1.4.1.248.15.1.2.15.8.5Unsigned32read-onlycurrent
hmAgentStpCstBridgeFwdDelay
OBJECT-TYPE
The MSTP bridge forward delay for the CIST. The default value is 15.
1.3.6.1.4.1.248.15.1.2.15.8.6Unsigned32 (4..30)read-writecurrent
hmAgentStpCstBridgeHelloTime
OBJECT-TYPE
The MSTP bridge hello time for the CIST. The default value is 2.
1.3.6.1.4.1.248.15.1.2.15.8.7Unsigned32 (1..2)read-writecurrent
hmAgentStpCstBridgeHoldTime
OBJECT-TYPE
The MSTP bridge hold time for the CIST.
1.3.6.1.4.1.248.15.1.2.15.8.8Unsigned32read-onlycurrent
hmAgentStpCstBridgeMaxAge
OBJECT-TYPE
The MSTP bridge max age for the CIST. The default value is 20.
1.3.6.1.4.1.248.15.1.2.15.8.9Unsigned32 (6..40)read-writecurrent
hmAgentStpCstBridgeDesignatedRoot
OBJECT-TYPE
The Designated Root like in dot1dStpDesignatedRoot.
1.3.6.1.4.1.248.15.1.2.15.8.10BridgeIdread-onlycurrent
hmAgentStpCstBridgePriority
OBJECT-TYPE
The MSTP bridge priority for the CIST. The default value is 32768.
1.3.6.1.4.1.248.15.1.2.15.8.11Unsigned32 (0..61440)read-writecurrent
hmAgentStpCstBridgeTimeSinceTopologyChange
OBJECT-TYPE
The time (in hundredths of a second) since the last time a topology change was detected by the bridge entity.
1.3.6.1.4.1.248.15.1.2.15.8.12TimeTicksread-onlycurrent
hmAgentStpCstBridgeTopChanges
OBJECT-TYPE
The total number of topology changes detected by this bridge since the management entity was last reset or initialized.
1.3.6.1.4.1.248.15.1.2.15.8.13Counter32read-onlycurrent
hmAgentStpCstBridgeRootCost
OBJECT-TYPE
The cost of the path to the root as seen from this bridge.
1.3.6.1.4.1.248.15.1.2.15.8.14Unsigned32read-onlycurrent
hmAgentStpCstBridgeRootPort
OBJECT-TYPE
The port number of the port which offers the lowest cost path from this bridge to the root bridge.
1.3.6.1.4.1.248.15.1.2.15.8.15Unsigned32read-onlycurrent
hmAgentStpCstBridgeMaxHops
OBJECT-TYPE
The MSTP bridge max hops for the CIST. The default value is 20.
1.3.6.1.4.1.248.15.1.2.15.8.16Unsigned32 (6..40)read-writecurrent
hmAgentStpCstBridgeHoldCount
OBJECT-TYPE
The MSTP bridge hold count for the CIST. This command sets the value of maximum bpdus that a bridge is allowed to send within a hello time window. The default value is 10.
1.3.6.1.4.1.248.15.1.2.15.8.17Unsigned32 (1..40)read-writecurrent
hmAgentStpCstPortTable
OBJECT-TYPE
CIST port table.
1.3.6.1.4.1.248.15.1.2.15.9not-accessiblecurrent
hmAgentStpCstPortEntry
OBJECT-TYPE
CIST port entry.
1.3.6.1.4.1.248.15.1.2.15.9.1not-accessiblecurrent
hmAgentStpCstPortOperEdge
OBJECT-TYPE
The MSTP operational status of a specific port for the CIST.
1.3.6.1.4.1.248.15.1.2.15.9.1.1INTEGER {true(1), false(2)}read-onlycurrent
hmAgentStpCstPortOperPointToPoint
OBJECT-TYPE
The MSTP operational point to point mac of a specific port for the CIST.
1.3.6.1.4.1.248.15.1.2.15.9.1.2INTEGER {true(1), false(2)}read-onlycurrent
hmAgentStpCstPortTopologyChangeAck
OBJECT-TYPE
The MSTP topology change acknowledge for a specific port in the CIST.
1.3.6.1.4.1.248.15.1.2.15.9.1.3INTEGER {true(1), false(2)}read-onlycurrent
hmAgentStpCstPortEdge
OBJECT-TYPE
The administrative state of a specific port in CIST. true(1) - port is edge port. false(2) - port is auto-edge or no edge port. The default port state is disabled.
1.3.6.1.4.1.248.15.1.2.15.9.1.4INTEGER {true(1), false(2)}read-writecurrent
hmAgentStpCstPortForwardingState
OBJECT-TYPE
The MSTP forwarding state of a specific port in CIST.
1.3.6.1.4.1.248.15.1.2.15.9.1.5INTEGER {discarding(1), learning(2), forwarding(3), disabled(4), manualFwd(5), notParticipate(6)}read-onlycurrent
hmAgentStpCstPortId
OBJECT-TYPE
The MSTP port identifier of a specific port in CIST.
1.3.6.1.4.1.248.15.1.2.15.9.1.6OCTET STRINGread-onlycurrent
hmAgentStpCstPortPathCost
OBJECT-TYPE
The MSTP port path cost in CIST. The default value will correspond to the recommendation specified in IEEE 802.1s Table 13-2 which varies depending upon link speed.
1.3.6.1.4.1.248.15.1.2.15.9.1.7Unsigned32 (0..200000000)read-writecurrent
hmAgentStpCstPortPriority
OBJECT-TYPE
The MSTP port priority in CIST. The priority is in the increments of 16. The default value is 128.
1.3.6.1.4.1.248.15.1.2.15.9.1.8Unsigned32 (0..240)read-writecurrent
hmAgentStpCstDesignatedBridgeId
OBJECT-TYPE
The MSTP designated bridge ID of a specific port in CIST.
1.3.6.1.4.1.248.15.1.2.15.9.1.9OCTET STRING (SIZE(8))read-onlycurrent
hmAgentStpCstDesignatedCost
OBJECT-TYPE
The MSTP designated cost of a specific port in CIST.
1.3.6.1.4.1.248.15.1.2.15.9.1.10Unsigned32read-onlycurrent
hmAgentStpCstDesignatedPortId
OBJECT-TYPE
The MSTP designated port ID of a specific port in CIST.
1.3.6.1.4.1.248.15.1.2.15.9.1.11OCTET STRING (SIZE(2))read-onlycurrent
hmAgentStpCstExtPortPathCost
OBJECT-TYPE
The MSTP external port path cost in CIST. The default value varies depending upon the link speed.
1.3.6.1.4.1.248.15.1.2.15.9.1.12Unsigned32 (0..200000000)read-writecurrent
hmAgentStpCstPortAutoEdge
OBJECT-TYPE
The auto edge state of a specific port in CIST. true(1) - enables the port. false(2) - disables the port. The default port state is enabled.
1.3.6.1.4.1.248.15.1.2.15.9.1.13INTEGER {true(1), false(2)}read-writecurrent
hmAgentStpCstPortRole
OBJECT-TYPE
The current Port Role for the Port (i.e., Root, Alternate, Designated, or Backup), for the CIST.
1.3.6.1.4.1.248.15.1.2.15.9.1.14INTEGER {root(1), alternate(2), designated(3), backup(4), master(5), disabled(6)}read-onlycurrent
hmAgentStpCstPortDisputed
OBJECT-TYPE
The current value of the disputed variable for the CIST for the Port. A value of true(1) indicates that the disputed variable is set. A value of false(2) indicates that the agreed variable is cleared.
1.3.6.1.4.1.248.15.1.2.15.9.1.15INTEGER {true(1), false(2)}read-onlycurrent
hmAgentStpCstPortBpduGuardEffect
OBJECT-TYPE
BPDU Guard Mode effect on the port. enable(1) - BPDU Guard Mode is enabled on the port. disable(2) - BPDU Guard Mode is disabled on the port.
1.3.6.1.4.1.248.15.1.2.15.9.1.16INTEGER {enable(1), disable(2)}read-onlycurrent
hmAgentStpCstPortBpduFilter
OBJECT-TYPE
This command sets BPDU Filter mode on the port. enable(1) - BPDU Filter Mode is enabled on the port. disable(2) - BPDU Filter Mode is disabled on the port.
1.3.6.1.4.1.248.15.1.2.15.9.1.17INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentStpCstPortBpduFlood
OBJECT-TYPE
This command sets BPDU Flood mode on the port. enable(1) - BPDU Flood Mode is enabled on the port. disable(2) - BPDU Flood Mode is disabled on the port.
1.3.6.1.4.1.248.15.1.2.15.9.1.18INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentStpCstPortRootGuard
OBJECT-TYPE
This command sets a port to discard any superior information received by the port and thus protect against root of the device from changing.The port gets put into discarding state and does not forward any packets. enable(1) - enables the root-guard mode for the port. disable(2) - disables the root-guard mode for the port. The default root-guard mode is disabled.
1.3.6.1.4.1.248.15.1.2.15.9.1.19INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentStpCstPortTCNGuard
OBJECT-TYPE
This command restricts the port from propagating any topology change information received through that port. enable(1) - enables the tcn-guard mode for the port. disable(2) - disables the tcn-guard mode for the port. The default tcn-guard mode is disabled.
1.3.6.1.4.1.248.15.1.2.15.9.1.20INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentStpCstPortLoopGuard
OBJECT-TYPE
This command enables loop guard on this port. This setting applies to all Spanning Tree instances of which this port is a member. enable(1) - enables the loop guard mode for the port. disable(2) - disables the loop guard mode for the port. The default loop-guard mode is disabled.
1.3.6.1.4.1.248.15.1.2.15.9.1.21INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentStpMstTable
OBJECT-TYPE
MST table.
1.3.6.1.4.1.248.15.1.2.15.10not-accessiblecurrent
hmAgentStpMstEntry
OBJECT-TYPE
MST entry.
1.3.6.1.4.1.248.15.1.2.15.10.1not-accessiblecurrent
hmAgentStpMstId
OBJECT-TYPE
The MSTP instance ID.
1.3.6.1.4.1.248.15.1.2.15.10.1.1Unsigned32read-onlycurrent
hmAgentStpMstBridgePriority
OBJECT-TYPE
The MSTP bridge priority in a specific instance. The priority is in the increments of 4096. The recommended default value is 32768.
1.3.6.1.4.1.248.15.1.2.15.10.1.2Unsigned32 (0..61440)read-writecurrent
hmAgentStpMstBridgeIdentifier
OBJECT-TYPE
The MSTP bridge identifier in a specific instance.
1.3.6.1.4.1.248.15.1.2.15.10.1.3OCTET STRING (SIZE(8))read-onlycurrent
hmAgentStpMstDesignatedRootId
OBJECT-TYPE
The MSTP designated root bridge identifier in a specific instance.
1.3.6.1.4.1.248.15.1.2.15.10.1.4OCTET STRING (SIZE(8))read-onlycurrent
hmAgentStpMstRootPathCost
OBJECT-TYPE
The MSTP root path cost in a specific instance.
1.3.6.1.4.1.248.15.1.2.15.10.1.5Unsigned32read-onlycurrent
hmAgentStpMstRootPortId
OBJECT-TYPE
The MSTP root port ID in a specific instance.
1.3.6.1.4.1.248.15.1.2.15.10.1.6OCTET STRINGread-onlycurrent
hmAgentStpMstTimeSinceTopologyChange
OBJECT-TYPE
The MSTP time since the last topology change in a specific instance.
1.3.6.1.4.1.248.15.1.2.15.10.1.7TimeTicksread-onlycurrent
hmAgentStpMstTopologyChangeCount
OBJECT-TYPE
The MSTP count of topology changes in a specific instance.
1.3.6.1.4.1.248.15.1.2.15.10.1.8Counter32read-onlycurrent
hmAgentStpMstTopologyChangeParm
OBJECT-TYPE
The MSTP topology change parameter in a specific instance.
1.3.6.1.4.1.248.15.1.2.15.10.1.9INTEGER {true(1), false(2)}read-onlycurrent
hmAgentStpMstRowStatus
OBJECT-TYPE
The MSTP instance status. Supported values: active(1) - valid instance. createAndGo(4) - used to create a new instance. destroy(6) - removes an instance.
1.3.6.1.4.1.248.15.1.2.15.10.1.10RowStatusread-createcurrent
hmAgentStpMstPortTable
OBJECT-TYPE
MST port table.
1.3.6.1.4.1.248.15.1.2.15.11not-accessiblecurrent
hmAgentStpMstPortEntry
OBJECT-TYPE
MST port entry.
1.3.6.1.4.1.248.15.1.2.15.11.1not-accessiblecurrent
hmAgentStpMstPortForwardingState
OBJECT-TYPE
The MSTP forwarding state of a specific port in a specific instance.
1.3.6.1.4.1.248.15.1.2.15.11.1.1INTEGER {discarding(1), learning(2), forwarding(3), disabled(4), manualFwd(5), notParticipate(6)}read-onlycurrent
hmAgentStpMstPortId
OBJECT-TYPE
The MSTP port identifier of a specific port in a specific instance.
1.3.6.1.4.1.248.15.1.2.15.11.1.2OCTET STRINGread-onlycurrent
hmAgentStpMstPortPathCost
OBJECT-TYPE
The MSTP port path cost in a specific instance. The default value will correspond to the recommendation specified in IEEE 802.1s Table 13-2 which varies depending upon link speed.
1.3.6.1.4.1.248.15.1.2.15.11.1.3Unsigned32 (0..200000000)read-writecurrent
hmAgentStpMstPortPriority
OBJECT-TYPE
The MSTP port priority in a specific instance. The priority is in the increments of 16. The default value is 128.
1.3.6.1.4.1.248.15.1.2.15.11.1.4Unsigned32 (0..240)read-writecurrent
hmAgentStpMstDesignatedBridgeId
OBJECT-TYPE
The MSTP designated bridge ID of a specific port in a specific instance.
1.3.6.1.4.1.248.15.1.2.15.11.1.5OCTET STRING (SIZE(8))read-onlycurrent
hmAgentStpMstDesignatedCost
OBJECT-TYPE
The MSTP designated cost of a specific port in a specific instance.
1.3.6.1.4.1.248.15.1.2.15.11.1.6Unsigned32read-onlycurrent
hmAgentStpMstDesignatedPortId
OBJECT-TYPE
The MSTP designated port ID of a specific port in a specific instance.
1.3.6.1.4.1.248.15.1.2.15.11.1.7OCTET STRING (SIZE(2))read-onlycurrent
hmAgentStpMstPortRole
OBJECT-TYPE
In an MSTP Bridge, the current Port Role for the Port (i.e., Root, Alternate, Designated, or Backup), for the MSTI.
1.3.6.1.4.1.248.15.1.2.15.11.1.8INTEGER {root(1), alternate(2), designated(3), backup(4), master(5), disabled(6)}read-onlycurrent
hmAgentStpMstPortDisputed
OBJECT-TYPE
In an MSTP Bridge, the current value of the disputed variable for the MSTI for the Port.
1.3.6.1.4.1.248.15.1.2.15.11.1.9INTEGER {true(1), false(2)}read-onlycurrent
hmAgentStpMstPortLoopInconsistentState
OBJECT-TYPE
The loop inconsistent state of a specific port in a specific instance. This value can only report as true(1) when loop guard is enabled on the port and the port has transitioned from blocking state in this MST instance.
1.3.6.1.4.1.248.15.1.2.15.11.1.10INTEGER {false(0), true(1)}read-onlycurrent
hmAgentStpMstPortTransitionsIntoLoopInconsistentState
OBJECT-TYPE
The number of times this interface has transitioned into loop inconsistent state.
1.3.6.1.4.1.248.15.1.2.15.11.1.11Counter32read-onlycurrent
hmAgentStpMstPortTransitionsOutOfLoopInconsistentState
OBJECT-TYPE
The number of times this interface has transitioned out of loop inconsistent state.
1.3.6.1.4.1.248.15.1.2.15.11.1.12Counter32read-onlycurrent
hmAgentStpMstReceivedBridgeId
OBJECT-TYPE
The MSTP received bridge ID on a specific port in a specific instance.
1.3.6.1.4.1.248.15.1.2.15.11.1.13OCTET STRING (SIZE(8))read-onlycurrent
hmAgentStpMstReceivedRPC
OBJECT-TYPE
The MSTP received root path cost of a specific port in a specific instance.
1.3.6.1.4.1.248.15.1.2.15.11.1.14Unsigned32read-onlycurrent
hmAgentStpMstReceivedPortId
OBJECT-TYPE
The MSTP received port ID on a specific port in a specific instance.
1.3.6.1.4.1.248.15.1.2.15.11.1.15OCTET STRING (SIZE(2))read-onlycurrent
hmAgentStpMstVlanTable
OBJECT-TYPE
MST VLAN table.
1.3.6.1.4.1.248.15.1.2.15.12not-accessiblecurrent
hmAgentStpMstVlanEntry
OBJECT-TYPE
MST VLAN entry.
1.3.6.1.4.1.248.15.1.2.15.12.1not-accessiblecurrent
hmAgentStpMstVlanRowStatus
OBJECT-TYPE
The association status of an MSTP instance and a VLAN. Supported values: active(1) - valid association between an MSTP instance and a VLAN. createAndGo(4) - used to create a new association between an MSTP instance and a VLAN. destroy(6) - removes the association between an MSTP instance and a VLAN.
1.3.6.1.4.1.248.15.1.2.15.12.1.1RowStatusread-createcurrent
hmAgentStpBpduGuardMode
OBJECT-TYPE
The spanning tree BPDU Guard Mode. enable(1) - enables BPDU Guard Mode on the switch. disable(2) - disables BPDU Guard Mode on the switch. The default status is disabled.
1.3.6.1.4.1.248.15.1.2.15.13INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentStpBpduFilterDefault
OBJECT-TYPE
The spanning tree BPDU Filter Mode, it enables BPDU Filter on all edge ports. enable(1) - enables BPDU Filter Mode on the switch. disable(2) - disables BPDU Filter Mode on the switch. The default status is disabled.
1.3.6.1.4.1.248.15.1.2.15.14INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentClassOfServiceGroup
OBJECT-IDENTITY
1.3.6.1.4.1.248.15.1.2.17
hmAgentClassOfServicePortTable
OBJECT-TYPE
A table that contains information about the 802.1p priority mapping to traffic class priority queue for every physical port.
1.3.6.1.4.1.248.15.1.2.17.1not-accessiblecurrent
hmAgentClassOfServicePortEntry
OBJECT-TYPE
A 802.1p priority mapped to a traffic class priority queue.
1.3.6.1.4.1.248.15.1.2.17.1.1not-accessiblecurrent
hmAgentClassOfServicePortPriority
OBJECT-TYPE
The Priority value determined for the received frame. This value is equivalent to the priority indicated in the tagged frame received, or one of the evaluated priorities, determined according to the media-type. For untagged frames received from Ethernet media, this value is equal to the dot1dPortDefaultUserPriority value for the ingress port.
1.3.6.1.4.1.248.15.1.2.17.1.1.1Integer32 (0..7)not-accessiblecurrent
hmAgentClassOfServicePortClass
OBJECT-TYPE
Traffic class priority queue the received frame is mapped to. The possible range depends on the number of supported traffic classes for the appropriate port, as shown in dot1dPortNumTrafficClasses.
1.3.6.1.4.1.248.15.1.2.17.1.1.2Integer32 (0..7)read-writecurrent
hmAgentSystemGroup
OBJECT-IDENTITY
1.3.6.1.4.1.248.15.1.3
hmAgentSaveConfig
OBJECT-TYPE
Enable hmAgentSaveConfig will initiate an configuration save to nvram. Disable hmAgentSaveConfig after a configuration save will reset hmAgentSaveConfigStatus back to notInitiated state.
1.3.6.1.4.1.248.15.1.3.1INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentClearConfig
OBJECT-TYPE
clear config to factory defaults
1.3.6.1.4.1.248.15.1.3.2INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentClearLags
OBJECT-TYPE
clear lag configuration
1.3.6.1.4.1.248.15.1.3.3INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentClearLoginSessions
OBJECT-TYPE
close all telnet sessions
1.3.6.1.4.1.248.15.1.3.4INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentClearPasswords
OBJECT-TYPE
reset passwords
1.3.6.1.4.1.248.15.1.3.5INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentClearPortStats
OBJECT-TYPE
clear all port statistics
1.3.6.1.4.1.248.15.1.3.6INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentClearSwitchStats
OBJECT-TYPE
clear all switch statistics
1.3.6.1.4.1.248.15.1.3.7INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentClearTrapLog
OBJECT-TYPE
clear trap log
1.3.6.1.4.1.248.15.1.3.8INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentClearVlan
OBJECT-TYPE
clear vlan entries
1.3.6.1.4.1.248.15.1.3.9INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentResetSystem
OBJECT-TYPE
reset the switch
1.3.6.1.4.1.248.15.1.3.10INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentSaveConfigStatus
OBJECT-TYPE
Indicates the current status of an save configuration request.
1.3.6.1.4.1.248.15.1.3.11INTEGER {notInitiated(1), savingInProcess(2), savingComplete(3)}read-onlycurrent
hmAgentCableTesterGroup
OBJECT-IDENTITY
1.3.6.1.4.1.248.15.1.4
hmAgentCableTesterStatus
OBJECT-TYPE
Status of the Virtual Cable Tester active(1) - cable testing is in progress. Set to this value to start the test. success(2) - A successful test was performed. Cannot be set. failure(3) - A failure was encountered during the test. Cannot be set. uninitialized(4) - No test has been performed yet. Cannot be set.
1.3.6.1.4.1.248.15.1.4.1INTEGER {active(1), success(2), failure(3), uninitialized(4)}read-writecurrent
hmAgentCableTesterIfIndex
OBJECT-TYPE
Determines on which port to perform the cable test. Limited to copper based ports.
1.3.6.1.4.1.248.15.1.4.2Unsigned32read-writecurrent
hmAgentCableTesterCableStatus
OBJECT-TYPE
Indicates the results of the Cable Test. normal(1) - The cable is working correctly. open(2) - The cable is disconnected or there is a faulty connector. short(3) - There is an electrical short in the cable. unknown(4) - No test has been performed yet, or a test is currently in progress.
1.3.6.1.4.1.248.15.1.4.3INTEGER {normal(1), open(2), short(3), unknown(4)}read-onlycurrent
hmAgentCableTesterMinimumCableLength
OBJECT-TYPE
The estimated length of the cable in meters. This value indicates the shortest length estimated. This object will return 0 if hmAgentCableTesterStatus is not success(2) or the cable length is unknown.
1.3.6.1.4.1.248.15.1.4.4Unsigned32read-onlycurrent
hmAgentCableTesterMaximumCableLength
OBJECT-TYPE
The estimated length of the cable in meters. This value indicates the longest length estimated. This object will return 0 if hmAgentCableTesterStatus is not success(2) or the cable length is unknown.
1.3.6.1.4.1.248.15.1.4.5Unsigned32read-onlycurrent
hmAgentCableTesterCableFailureLocation
OBJECT-TYPE
The estimated distance in meters from the end of the cable to the failure location. This object will return 0 if hmAgentCableTesterStatus is not success(2).
1.3.6.1.4.1.248.15.1.4.6Unsigned32read-onlycurrent
hmPlatform4SwitchingTraps
OBJECT-IDENTITY
1.3.6.1.4.1.248.15.1.50
hmRadius
OBJECT-IDENTITY
1.3.6.1.4.1.248.15.8
hmAgentRadiusConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.248.15.8.1
hmAgentRadiusMaxTransmit
OBJECT-TYPE
Maximum number of retransmissions of a RADIUS request packet
1.3.6.1.4.1.248.15.8.1.1Unsigned32 (1..15)read-writecurrent
hmAgentRadiusTimeout
OBJECT-TYPE
Time out duration (in seconds) before packets are retransmitted
1.3.6.1.4.1.248.15.8.1.2Unsigned32 (1..30)read-writecurrent
hmAgentRadiusAccountingMode
OBJECT-TYPE
Identifies if RADIUS Accounting has been enabled or not
1.3.6.1.4.1.248.15.8.1.3INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentRadiusStatsClear
OBJECT-TYPE
When set to enable(1), all Radius statistics will be reset.
1.3.6.1.4.1.248.15.8.1.4INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentRadiusAccountingIndexNextValid
OBJECT-TYPE
Indicates the next valid index into the hmAgentRadiusAccountingConfigTable for creation. If no additional entries are allowed, this will be 0.
1.3.6.1.4.1.248.15.8.1.5Integer32 (0 | 1..2147483647)read-onlycurrent
hmAgentRadiusAccountingConfigTable
OBJECT-TYPE
Table with information about Radius Accounting Server IP Addresses, port numbers and shared secret. Only one entry is supported at this time.
1.3.6.1.4.1.248.15.8.1.6not-accessiblecurrent
hmAgentRadiusAccountingConfigEntry
OBJECT-TYPE
Entry consisting of configuration data for a Radius Accounting Server.
1.3.6.1.4.1.248.15.8.1.6.1not-accessiblecurrent
hmAgentRadiusAccountingServerIndex
OBJECT-TYPE
Unique index of the configured RADIUS accounting server. The next valid value of this object for creation is specified by hmAgentRadiusAccountingIndexNextValid.
1.3.6.1.4.1.248.15.8.1.6.1.1Integer32 (1..2147483647)not-accessiblecurrent
hmAgentRadiusAccountingServerAddress
OBJECT-TYPE
IP Address of the configured RADIUS accounting server. This object cannot be changed after creation.
1.3.6.1.4.1.248.15.8.1.6.1.2IpAddressread-createcurrent
hmAgentRadiusAccountingPort
OBJECT-TYPE
Port number for the RADIUS accounting server.
1.3.6.1.4.1.248.15.8.1.6.1.3Unsigned32 (0..65535)read-writecurrent
hmAgentRadiusAccountingSecret
OBJECT-TYPE
Configured shared sercret for the RADIUS accounting server.
1.3.6.1.4.1.248.15.8.1.6.1.4DisplayString (SIZE(1..20))read-writecurrent
hmAgentRadiusAccountingStatus
OBJECT-TYPE
Creates or destroys a RADIUS accounting server entry. During creation, the next available index is specified by the hmAgentRadiusAccountingIndexNextValid object. Rows creation using a different value for hmAgentRadiusAccountingServerIndex will fail. active(1) - This entry is active. createAndGo(4) - Creates a new entry. destroy(6) - Deletes an entry.
1.3.6.1.4.1.248.15.8.1.6.1.5RowStatusread-createcurrent
hmAgentRadiusServerIndexNextValid
OBJECT-TYPE
Indicates the next valid index into the hmAgentRadiusServerConfigTable for creation. If no additional entries are allowed, this will be 0.
1.3.6.1.4.1.248.15.8.1.7Integer32 (0 | 1..2147483647)read-onlycurrent
hmAgentRadiusServerConfigTable
OBJECT-TYPE
Table with information about Radius Authentication Server IP Addresses, port numbers and shared secret
1.3.6.1.4.1.248.15.8.1.8not-accessiblecurrent
hmAgentRadiusServerConfigEntry
OBJECT-TYPE
Entry consisting of configuration data for a Radius Authentication Server.
1.3.6.1.4.1.248.15.8.1.8.1not-accessiblecurrent
hmAgentRadiusServerIndex
OBJECT-TYPE
Unique index of the configured RADIUS server
1.3.6.1.4.1.248.15.8.1.8.1.1Integer32 (1..2147483647)not-accessiblecurrent
hmAgentRadiusServerAddress
OBJECT-TYPE
IP Address of the configured RADIUS server. This object cannot be changed after creation.
1.3.6.1.4.1.248.15.8.1.8.1.2IpAddressread-createcurrent
hmAgentRadiusServerPort
OBJECT-TYPE
Port number for the RADIUS server.
1.3.6.1.4.1.248.15.8.1.8.1.3Unsigned32 (0..65535)read-writecurrent
hmAgentRadiusServerSecret
OBJECT-TYPE
Configured shared sercret for the RADIUS server.
1.3.6.1.4.1.248.15.8.1.8.1.4DisplayString (SIZE(1..20))read-writecurrent
hmAgentRadiusServerPrimaryMode
OBJECT-TYPE
Configure the RADIUS server to be the primary server. If there is any other server that is configured to be primary, that server is set to be a seconday server and this entry is set Primary.
1.3.6.1.4.1.248.15.8.1.8.1.5INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentRadiusServerCurrentMode
OBJECT-TYPE
Indicate if the RADIUS server is the current server in user for authentication.
1.3.6.1.4.1.248.15.8.1.8.1.6INTEGER {yes(1), no(2)}read-onlycurrent
hmAgentRadiusServerMsgAuth
OBJECT-TYPE
Enable or disable the message authenticator attribute for this RADIUS server.
1.3.6.1.4.1.248.15.8.1.8.1.7INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentRadiusServerStatus
OBJECT-TYPE
Creates or destroys a RADIUS Authentication server entry. During creation, the next available index is specified by the hmAgentRadiusServerIndexNextValid object. Rows creation using a different value for hmAgentRadiusServerIndex will fail. active(1) - This entry is active. createAndGo(4) - Creates a new entry. destroy(6) - Deletes an entry.
1.3.6.1.4.1.248.15.8.1.8.1.8RowStatusread-createcurrent
hmAgentMgmtSecurity
OBJECT-IDENTITY
1.3.6.1.4.1.248.15.11
hmAgentSSHConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.248.15.11.2
hmAgentSSHAdminMode
OBJECT-TYPE
Configures whether the SSH service is enabled on this switch. The default value is disable(2).
1.3.6.1.4.1.248.15.11.2.1INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentSSHProtocolLevel
OBJECT-TYPE
Configures which protocol versions of SSH are enabled on this switch. The default value is both(3).
1.3.6.1.4.1.248.15.11.2.2INTEGER {ssh10(1), ssh20(2), both(3)}read-writecurrent
hmAgentSSHSessionsCount
OBJECT-TYPE
Current number of active SSH sessions on this switch.
1.3.6.1.4.1.248.15.11.2.3Integer32read-onlycurrent
hmAgentSSHMaxSessionsCount
OBJECT-TYPE
Max number of SSH sessions permitted on this switch.
1.3.6.1.4.1.248.15.11.2.4Integer32 (0..5)read-writecurrent
hmAgentSSHSessionTimeout
OBJECT-TYPE
ssh idle timeout value for this switch im minutes.
1.3.6.1.4.1.248.15.11.2.5Integer32 (1..160)read-writecurrent
hmAgentLogging
OBJECT-IDENTITY
1.3.6.1.4.1.248.15.14
hmAgentLogConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.248.15.14.1
hmAgentLogSysLogConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.248.15.14.1.4
hmAgentLogSyslogAdminStatus
OBJECT-TYPE
For Enabling and Disabling logging to configured syslog hosts. Setting this to disable stops logging to all syslog hosts.
1.3.6.1.4.1.248.15.14.1.4.1INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentLogSyslogHostTable
OBJECT-TYPE
Syslog host table containing syslog host entries.
1.3.6.1.4.1.248.15.14.1.4.5not-accessiblecurrent
hmAgentLogSyslogHostEntry
OBJECT-TYPE
Syslog Host entry attributes.
1.3.6.1.4.1.248.15.14.1.4.5.1not-accessiblecurrent
hmAgentLogHostTableIndex
OBJECT-TYPE
Index to syslog host entry in syslog host table.
1.3.6.1.4.1.248.15.14.1.4.5.1.1Unsigned32not-accessiblecurrent
hmAgentLogHostTableIpAddress
OBJECT-TYPE
Syslog Host table IP Address.
1.3.6.1.4.1.248.15.14.1.4.5.1.3IpAddressread-createcurrent
hmAgentLogHostTablePort
OBJECT-TYPE
Syslog Host table port number.
1.3.6.1.4.1.248.15.14.1.4.5.1.4Unsigned32 (1..65535)read-createcurrent
hmAgentLogHostTableSeverityFilter
OBJECT-TYPE
Configures the minimum severity that will be stored in the In Memory log.
1.3.6.1.4.1.248.15.14.1.4.5.1.5HmAgentLogSeverityread-createcurrent
hmAgentLogHostTableRowStatus
OBJECT-TYPE
Syslog Host table row status
1.3.6.1.4.1.248.15.14.1.4.5.1.7RowStatusread-createcurrent
hmPlatform4OutboundTelnetPrivate
OBJECT-IDENTITY
1.3.6.1.4.1.248.15.19
hmAgentOutboundTelnetGroup
OBJECT-IDENTITY
1.3.6.1.4.1.248.15.19.1
hmAgentOutboundTelnetAdminMode
OBJECT-TYPE
Admin-mode of the Outbound Telnet.
1.3.6.1.4.1.248.15.19.1.1INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentOutboundTelnetMaxNoOfSessions
OBJECT-TYPE
The maximum no. of Outbound Telnet sessions allowed.
1.3.6.1.4.1.248.15.19.1.2Integer32 (0..5)read-writecurrent
hmAgentOutboundTelnetTimeout
OBJECT-TYPE
The login inactivity timeout value for Outbound Telnet.
1.3.6.1.4.1.248.15.19.1.3Integer32 (0..160)read-writecurrent
hmAgentDot1xAdvanced
OBJECT-IDENTITY
1.3.6.1.4.1.248.15.36
hmAgentDot1xEnhancementConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.248.15.36.1
hmAgentDot1xRadiusVlanAssignment
OBJECT-TYPE
Enable/Disable dot1x Vlan Assignment Support on the switch.
1.3.6.1.4.1.248.15.36.1.1INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentDot1xDynamicVlanCreationMode
OBJECT-TYPE
Enable/Disable dot1x dynamic vlan creation Support on the switch.
1.3.6.1.4.1.248.15.36.1.2INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentDot1xSafeVlanMode
OBJECT-TYPE
Enable/Disable dot1x safe vlan assignment on the switch for multi-client authentication.
1.3.6.1.4.1.248.15.36.1.3INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentDot1xPortConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.248.15.36.2
hmAgentDot1xPortConfigTable
OBJECT-TYPE
A table for dot1x enhanced Port details and associated functionality.
1.3.6.1.4.1.248.15.36.2.1not-accessiblecurrent
hmAgentDot1xPortConfigEntry
OBJECT-TYPE
Represents entry for port config table.
1.3.6.1.4.1.248.15.36.2.1.1not-accessiblecurrent
hmAgentDot1xPortControlMode
OBJECT-TYPE
Dot1x port control mode of this port.The Port control mode . The port control mode for this interface can take the following values , force-unauthorized - the port is in unauthorized mode, auto-Port based mode. If a client authenticates suscessfully, then the interface is authorized . Otherwise, the port is in unauthorized mode. If more than one clients are attached to the port , then only one client needs to authenticate to allow other clients access. force-authorized - The port is placed in authorized mode macBased - If more than one client is attached to the port, then each client needs to authenticate separately. This object depcreates dot1xAuthAuthControlledPortControl object in IEEE8021-PAE-MIB
1.3.6.1.4.1.248.15.36.2.1.1.1HmAgentDot1xPortControlModeread-writecurrent
hmAgentDot1xGuestVlanId
OBJECT-TYPE
Specifies the Guest Vlan of the port. A port will be moved to its Guest Vlan if no client sucessfully authenticates on that port for the Guest Vlan Period. A value of zero indicates no Guest Vlan is configured for the interface.
1.3.6.1.4.1.248.15.36.2.1.1.2Unsigned32read-writecurrent
hmAgentDot1xGuestVlanPeriod
OBJECT-TYPE
The value, in seconds, of the guestVlanPeriod constant currently in use for Guest Vlan Assignment for the port .
1.3.6.1.4.1.248.15.36.2.1.1.3Unsigned32 (0..65535)read-writecurrent
hmAgentDot1xUnauthenticatedVlan
OBJECT-TYPE
Specifies the Unauthenticated Vlan of the port. A port will be moved to its unauthenticated Vlan if the client authenticates unsucessfully on that port . A value of zero indicates no Unauthenticated Vlan is configured for the port.
1.3.6.1.4.1.248.15.36.2.1.1.4Unsigned32read-writecurrent
hmAgentDot1xMaxUsers
OBJECT-TYPE
Specifies the maximum users or clients that can authenticate on this port when the port control mode is macBased.
1.3.6.1.4.1.248.15.36.2.1.1.5Unsigned32read-writecurrent
hmAgentDot1xPortVlanAssigned
OBJECT-TYPE
Specifies the vlan the port is assigned to by Dot1x . Only relevant if the port control mode of the port is auto.
1.3.6.1.4.1.248.15.36.2.1.1.6Unsigned32read-onlycurrent
hmAgentDot1xPortVlanAssignedReason
OBJECT-TYPE
Reason the port is assigned to the vlan specified by hmAgentDot1xPortVlanAssigned . Only relevant if the port control mode of the port is auto.
1.3.6.1.4.1.248.15.36.2.1.1.7INTEGER {default(1), radius(2), unauthenticatedVlan(3), guestVlan(4), voiceVlan(5), notAssigned(7)}read-onlycurrent
hmAgentDot1xPortSessionTimeout
OBJECT-TYPE
Specifies the session timeout value assigned by the Radius server for this port . Only relevant if the port control mode of the port is auto.
1.3.6.1.4.1.248.15.36.2.1.1.8Unsigned32read-onlycurrent
hmAgentDot1xPortTerminationAction
OBJECT-TYPE
Specifies the session termination action assigned by the Radius Server .This is the action taken when the session times out . Only relevant if the port control mode of the port is auto.
1.3.6.1.4.1.248.15.36.2.1.1.9HmAgentDot1xSessionTerminationActionread-onlycurrent
hmAgentDot1xPortMABenabled
OBJECT-TYPE
Specifies if Mac-based bypass authentication is configured for the port.
1.3.6.1.4.1.248.15.36.2.1.1.10INTEGER {enable(1), disable(2)}read-writecurrent
hmAgentDot1xPortMABenabledOperational
OBJECT-TYPE
Displays the operational value of the Mac-based authentication bypass mode (MAB) on the port.
1.3.6.1.4.1.248.15.36.2.1.1.11INTEGER {enable(1), disable(2)}read-onlycurrent
hmAgentDot1xClientConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.248.15.36.3
hmAgentDot1xClientConfigTable
OBJECT-TYPE
A table for dot1x Client details and associated functionality.
1.3.6.1.4.1.248.15.36.3.1not-accessiblecurrent
hmAgentDot1xClientConfigEntry
OBJECT-TYPE
Represents entry for port config table.
1.3.6.1.4.1.248.15.36.3.1.1not-accessiblecurrent
hmAgentDot1xClientMacAddress
OBJECT-TYPE
Specifies the client MAC address of the client.
1.3.6.1.4.1.248.15.36.3.1.1.1MacAddressread-onlycurrent
hmAgentDot1xLogicalPort
OBJECT-TYPE
Specifies the client MAC address of the client .
1.3.6.1.4.1.248.15.36.3.1.1.2Unsigned32read-onlycurrent
hmAgentDot1xInterface
OBJECT-TYPE
Specifies the physical interface to which the client is attached .
1.3.6.1.4.1.248.15.36.3.1.1.3Unsigned32read-onlycurrent
hmAgentDot1xClientAuthPAEstate
OBJECT-TYPE
The current value of the Authenticator PAE state machine for the client.
1.3.6.1.4.1.248.15.36.3.1.1.4INTEGER {initialize(1), disconnected(2), connecting(3), authenticating(4), authenticated(5), aborting(6), held(7), forceAuth(8), forceUnauth(9)}read-onlycurrent
hmAgentDot1xClientBackendState
OBJECT-TYPE
The current state of the Backend Authentication state machine.
1.3.6.1.4.1.248.15.36.3.1.1.5INTEGER {request(1), response(2), success(3), fail(4), timeout(5), idle(6), initialize(7)}read-onlycurrent
hmAgentDot1xClientUserName
OBJECT-TYPE
Specifies the username with which the client is authenticated to the Radius server . This value is only valid when the client is in authenticated state.
1.3.6.1.4.1.248.15.36.3.1.1.6DisplayStringread-onlycurrent
hmAgentDot1xClientSessionTime
OBJECT-TYPE
Specifies the time elapsed in seconds since the client was authenticated in this session. This value is only valid when the client is in authenticated state.
1.3.6.1.4.1.248.15.36.3.1.1.7Unsigned32read-onlycurrent
hmAgentDot1xClientFilterID
OBJECT-TYPE
Specifies the Filter ID or Diffserv Policy name to be applied to the session . This vlaue is populated only if it has been assigned by the RADIUS server. This value is only valid when the client is in authenticated state.
1.3.6.1.4.1.248.15.36.3.1.1.8DisplayStringread-onlycurrent
hmAgentDot1xClientVlanAssigned
OBJECT-TYPE
Specifies the vlan the client is associated with by Dot1x . This value is only valid when the client is in authenticated state.
1.3.6.1.4.1.248.15.36.3.1.1.9Unsigned32read-onlycurrent
hmAgentDot1xClientVlanAssignedReason
OBJECT-TYPE
Reason the client is associated to the vlan specified by hmAgentDot1xClientVlanAssigned . This value is only valid when the client is in authenticated state.
1.3.6.1.4.1.248.15.36.3.1.1.10INTEGER {default(1), radius(2), unauthenticatedVlan(3), guestVlan(4), voiceVlan(5), invalid(7)}read-onlycurrent
hmAgentDot1xClientSessionTimeout
OBJECT-TYPE
Specifies the session time remaining for the client if assigned by the Radius server . A value of 0 indicates that no session timeout was assigned by the RADIUS server. This value is only valid when the client is in authenticated state.
1.3.6.1.4.1.248.15.36.3.1.1.11Unsigned32read-onlycurrent
hmAgentDot1xClientTerminationAction
OBJECT-TYPE
Specifies the session termination action assigned by the Radius Server . This is the action taken when the session times out . This value is only valid when the client is in authenticated state.
1.3.6.1.4.1.248.15.36.3.1.1.12HmAgentDot1xSessionTerminationActionread-onlycurrent
dot1xTraps
OBJECT-IDENTITY
1.3.6.1.4.1.248.15.36.4

Notifications

NameOIDStatus
multipleUsersTrap
NOTIFICATION-TYPE
This trap is sent when more than one user is logged in with administrative access. Only applies to CLI interface.
1.3.6.1.4.1.248.15.1.50.1current
broadcastStormStartTrap
NOTIFICATION-TYPE
Trap is obsolete.
1.3.6.1.4.1.248.15.1.50.2obsolete
broadcastStormEndTrap
NOTIFICATION-TYPE
Trap is obsolete.
1.3.6.1.4.1.248.15.1.50.3obsolete
linkFailureTrap
NOTIFICATION-TYPE
Trap is obsolete.
1.3.6.1.4.1.248.15.1.50.4obsolete
vlanRequestFailureTrap
NOTIFICATION-TYPE
Trap is obsolete.
1.3.6.1.4.1.248.15.1.50.5obsolete
vlanDeleteLastTrap
NOTIFICATION-TYPE
Trap is sent when attempting to delete the last configured VLAN or the Default VLAN.
1.3.6.1.4.1.248.15.1.50.6current
vlanDefaultCfgFailureTrap
NOTIFICATION-TYPE
Trap is sent if there are failures in resetting VLAN configuration to defaults.
1.3.6.1.4.1.248.15.1.50.7current
vlanRestoreFailureTrap
NOTIFICATION-TYPE
Trap is obsolete.
1.3.6.1.4.1.248.15.1.50.8obsolete
fanFailureTrap
NOTIFICATION-TYPE
Trap is obsolete.
1.3.6.1.4.1.248.15.1.50.9obsolete
stpInstanceNewRootTrap
NOTIFICATION-TYPE
Trap is sent when this machine is a new STP Root when there is more than one STP instance.
1.3.6.1.4.1.248.15.1.50.10current
stpInstanceTopologyChangeTrap
NOTIFICATION-TYPE
Trap is sent when there is a STP topology change when there is more than one STP instance.
1.3.6.1.4.1.248.15.1.50.11current
powerSupplyStatusChangeTrap
NOTIFICATION-TYPE
Trap is obsolete.
1.3.6.1.4.1.248.15.1.50.12obsolete
failedUserLoginTrap
NOTIFICATION-TYPE
Trap is sent when a user fails to authenticate via the CLI or Web interfaces.
1.3.6.1.4.1.248.15.1.50.13current
dot1xPortStatusAuthorized
NOTIFICATION-TYPE
DOT1X port status is authorized.
1.3.6.1.4.1.248.15.36.4.1current
dot1xPortStatusUnauthorized
NOTIFICATION-TYPE
DOT1X port status is unauthorized.
1.3.6.1.4.1.248.15.36.4.2current