MIBs Depot

CISCOSB-BRIDGEMIBOBJECTS-MIB

Registered at
1.3.6.1.4.1.9.6.1.101.57
Last updated
2007-01-02 00:00
Organization
Cisco Systems, Inc.
Revisions
2007-01-02 00:00
Namespace
cisco
Source file
CISCOSB-BRIDGEMIBOBJECTS-MIB
Digest
sha256:f8157edccb709f5cabe48c0a899b57c2f1ad71eb7f9603602b4f75d74a6437a0

Description

This private MIB module defines bridge MIB objects private MIBs.

Contact

Postal: 170 West Tasman Drive San Jose , CA 95134-1706 USA Website: Cisco Small Business Support Community <http://www.cisco.com/go/smallbizsupport>

Imports

FromSymbols
BRIDGE-MIBBridgeId, MacAddress, Timeout, dot1dBasePort, dot1dStpPort
CISCOSB-MIBswitch001
IF-MIBInterfaceIndex, InterfaceIndexOrZero, ifIndex
Q-BRIDGE-MIBPortList
SNMP-FRAMEWORK-MIBSnmpAdminString
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP
SNMPv2-SMICounter32, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, iso
SNMPv2-TCDisplayString, RowStatus, TEXTUAL-CONVENTION, TruthValue

Imported by

8 module(s) in this corpus import this one.

Load order

Every file a consumer needs in order to load this module, dependencies first.

BRIDGE-MIB
CISCOSB-BRIDGEMIBOBJECTS-MIB
CISCOSB-MIB
IANAifType-MIB
IF-MIB
P-BRIDGE-MIB
Q-BRIDGE-MIB
RFC1158-MIB
RFC1271-MIB
RMON-MIB
RMON2-MIB
SNMP-FRAMEWORK-MIB
SNMPv2-CONF
SNMPv2-MIB
SNMPv2-SMI
SNMPv2-TC
TOKEN-RING-RMON-MIB

Under this module's arcs

Where the registration tree carries on below this module.

ArcNameModule
1.3.6.1.4.1.9.6.1.101.57.8rlq_bridge_mibCISCOSB-rldot1q-MIB

Textual conventions

NameOIDSyntaxAccessStatus
VlanList1
TEXTUAL-CONVENTION
Each octet within this value specifies a set of eight vlans, with the first octet specifying vlan 1 through 8, the second octet specifying vlan 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered vlan, and the least significant bit represents the highest numbered vlan. Thus, each vlan of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that vlan is included in the set of vlans; the vlan is not included if its bit has a value of '0'. VlanList1 represent vlans 1-1024
current
VlanList2
TEXTUAL-CONVENTION
As VlanList1 but represent vlans 1025-2048
current
VlanList3
TEXTUAL-CONVENTION
As VlanList1 but represent vlans 2049-3072
current
VlanList4
TEXTUAL-CONVENTION
As VlanList1 but represent vlans 3073-4094
current

Objects

NameOIDSyntaxAccessStatus
rldot1dPriority
OBJECT-IDENTITY
1.3.6.1.4.1.9.6.1.101.57.1
rldot1dPriorityMibVersion
OBJECT-TYPE
MIB's version, the current version is 1.
1.3.6.1.4.1.9.6.1.101.57.1.1INTEGERread-onlycurrent
rldot1dPriorityPortGroupTable
OBJECT-TYPE
A list of PortGroupNumber for each port.
1.3.6.1.4.1.9.6.1.101.57.1.2not-accessiblecurrent
rldot1dPriorityPortGroupEntry
OBJECT-TYPE
All ports belonging to a same group have the same User Priority to Traffic Class mapping.
1.3.6.1.4.1.9.6.1.101.57.1.2.1not-accessiblecurrent
rldot1dPriorityPortGroupNumber
OBJECT-TYPE
A group, that port belongs to. All ports belonging to a same group have the same User Priority to Traffic Class mapping.
1.3.6.1.4.1.9.6.1.101.57.1.2.1.1INTEGERread-onlycurrent
rldot1dStp
OBJECT-IDENTITY
1.3.6.1.4.1.9.6.1.101.57.2
rldot1dStpMibVersion
OBJECT-TYPE
MIB's version, the current version is 2.
1.3.6.1.4.1.9.6.1.101.57.2.1INTEGERread-onlycurrent
rldot1dStpType
OBJECT-TYPE
Specifies whether the device supports Spanning Tree per device, or per group.
1.3.6.1.4.1.9.6.1.101.57.2.2INTEGER {perDevice(1), mstp(4)}read-onlycurrent
rldot1dStpEnable
OBJECT-TYPE
Enable / Disable spanning tree. When working in per vlan mode enable / disable STP per all vlans.
1.3.6.1.4.1.9.6.1.101.57.2.3TruthValueread-writecurrent
rldot1dStpPortMustBelongToVlan
OBJECT-TYPE
Specifies whether a port must belong to a VLAN in order to participate in the STP.
1.3.6.1.4.1.9.6.1.101.57.2.4TruthValueread-writecurrent
rldot1dStpExtendedPortNumberFormat
OBJECT-TYPE
Specifies whether the STP uses the extended port fnumber format.
1.3.6.1.4.1.9.6.1.101.57.2.5TruthValueread-writecurrent
rldot1dStpVlanTable
OBJECT-TYPE
A table that contains vlan-specific information for the Spanning Tree Protocol.
1.3.6.1.4.1.9.6.1.101.57.2.6not-accessiblecurrent
rldot1dStpVlanEntry
OBJECT-TYPE
A list of information maintained by every Vlan about the Spanning Tree Protocol state for that Vlan.
1.3.6.1.4.1.9.6.1.101.57.2.6.1not-accessiblecurrent
rldot1dStpVlan
OBJECT-TYPE
The Vlan index.
1.3.6.1.4.1.9.6.1.101.57.2.6.1.1INTEGERread-onlycurrent
rldot1dStpVlanEnable
OBJECT-TYPE
Specifies whether this vlan is STP enable or disable
1.3.6.1.4.1.9.6.1.101.57.2.6.1.2TruthValueread-writecurrent
rldot1dStpTimeSinceTopologyChange
OBJECT-TYPE
The time (in hundredths of a second) since the last time a topology change was detected by the bridge entity.
1.3.6.1.4.1.9.6.1.101.57.2.6.1.3TimeTicksread-onlycurrent
rldot1dStpTopChanges
OBJECT-TYPE
The total number of topology changes detected by this bridge since the management entity was last reset or initialized.
1.3.6.1.4.1.9.6.1.101.57.2.6.1.4Counterread-onlycurrent
rldot1dStpDesignatedRoot
OBJECT-TYPE
The bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node.
1.3.6.1.4.1.9.6.1.101.57.2.6.1.5BridgeIdread-onlycurrent
rldot1dStpRootCost
OBJECT-TYPE
The cost of the path to the root as seen from this bridge.
1.3.6.1.4.1.9.6.1.101.57.2.6.1.6INTEGERread-onlycurrent
rldot1dStpRootPort
OBJECT-TYPE
The port number of the port which offers the lowest cost path from this bridge to the root bridge.
1.3.6.1.4.1.9.6.1.101.57.2.6.1.7INTEGERread-onlycurrent
rldot1dStpMaxAge
OBJECT-TYPE
The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.
1.3.6.1.4.1.9.6.1.101.57.2.6.1.8Timeoutread-onlycurrent
rldot1dStpHelloTime
OBJECT-TYPE
The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using.
1.3.6.1.4.1.9.6.1.101.57.2.6.1.9Timeoutread-onlycurrent
rldot1dStpHoldTime
OBJECT-TYPE
This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second.
1.3.6.1.4.1.9.6.1.101.57.2.6.1.10INTEGERread-onlycurrent
rldot1dStpForwardDelay
OBJECT-TYPE
This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. [Note that this value is the one that this bridge is currently using, in contrast to dot1dStpBridgeForwardDelay which is the value that this bridge and all others would start using if/when this bridge were to become the root.]
1.3.6.1.4.1.9.6.1.101.57.2.6.1.11Timeoutread-onlycurrent
rldot1dStpVlanPortTable
OBJECT-TYPE
A table that contains pair <vlan, port> specific information for the Spanning Tree Protocol.
1.3.6.1.4.1.9.6.1.101.57.2.7not-accessiblecurrent
rldot1dStpVlanPortEntry
OBJECT-TYPE
A list of information maintained by every pair <vlan, port> about the Spanning Tree Protocol state for that pair.
1.3.6.1.4.1.9.6.1.101.57.2.7.1not-accessiblecurrent
rldot1dStpVlanPortVlan
OBJECT-TYPE
The Vlan number that the port belongs to, and for which this entry contains Spanning Tree Protocol management information.
1.3.6.1.4.1.9.6.1.101.57.2.7.1.1INTEGER (1..4095)read-onlycurrent
rldot1dStpVlanPortPort
OBJECT-TYPE
The port number of the port for which this entry contains Spanning Tree Protocol management information.
1.3.6.1.4.1.9.6.1.101.57.2.7.1.2INTEGER (1..4096)read-onlycurrent
rldot1dStpVlanPortPriority
OBJECT-TYPE
The value of the priority field which is contained in the more significant 4 bits of the most significant octet of the (2 octet long) Port ID. The other octet of the Port ID is given by the value of rldot1dStpVlanPort.
1.3.6.1.4.1.9.6.1.101.57.2.7.1.3INTEGER (0..255)read-writecurrent
rldot1dStpVlanPortState
OBJECT-TYPE
The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning it will place that port into the broken(6) state. For ports which are disabled (see dot1dStpVlanPortEnable), this object will have a value of disabled(1).
1.3.6.1.4.1.9.6.1.101.57.2.7.1.4INTEGER {disabled(1), blocking(2), listening(3), learning(4), forwarding(5), broken(6)}read-onlycurrent
rldot1dStpVlanPortEnable
OBJECT-TYPE
The enabled/disabled status of the port.
1.3.6.1.4.1.9.6.1.101.57.2.7.1.5INTEGER {enabled(1), disabled(2)}read-writecurrent
rldot1dStpVlanPortPathCost
OBJECT-TYPE
The contribution of this port to the path cost of paths towards the spanning tree root which include this port. 802.1D-1990 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN.
1.3.6.1.4.1.9.6.1.101.57.2.7.1.6INTEGER (1..65535)read-writecurrent
rldot1dStpVlanPortDesignatedRoot
OBJECT-TYPE
The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached.
1.3.6.1.4.1.9.6.1.101.57.2.7.1.7BridgeIdread-onlycurrent
rldot1dStpVlanPortDesignatedCost
OBJECT-TYPE
The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs.
1.3.6.1.4.1.9.6.1.101.57.2.7.1.8INTEGERread-onlycurrent
rldot1dStpVlanPortDesignatedBridge
OBJECT-TYPE
The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment.
1.3.6.1.4.1.9.6.1.101.57.2.7.1.9BridgeIdread-onlycurrent
rldot1dStpVlanPortDesignatedPort
OBJECT-TYPE
The Port Identifier of the port on the Designated Bridge for this port's segment.
1.3.6.1.4.1.9.6.1.101.57.2.7.1.10OCTET STRING (SIZE(2))read-onlycurrent
rldot1dStpVlanPortForwardTransitions
OBJECT-TYPE
The number of times this port has transitioned from the Learning state to the Forwarding state.
1.3.6.1.4.1.9.6.1.101.57.2.7.1.11Counterread-onlycurrent
rldot1dStpTrapVariable
OBJECT-IDENTITY
1.3.6.1.4.1.9.6.1.101.57.2.8
rldot1dStpTrapVrblifIndex
OBJECT-TYPE
The ifIndex of port which STP status was changed
1.3.6.1.4.1.9.6.1.101.57.2.8.1InterfaceIndexread-onlycurrent
rldot1dStpTrapVrblVID
OBJECT-TYPE
The VID of VLAN to which the port belongs which STP status was changed
1.3.6.1.4.1.9.6.1.101.57.2.8.2INTEGERread-onlycurrent
rldot1dStpTypeAfterReset
OBJECT-TYPE
New mode of spaning tree supported by the device after the next reset.
1.3.6.1.4.1.9.6.1.101.57.2.9INTEGER {perDevice(1), mstp(4)}read-writecurrent
rldot1dStpMonitorTime
OBJECT-TYPE
Factor of hello-time during which a port is monotored to determine if it is stable.
1.3.6.1.4.1.9.6.1.101.57.2.10INTEGER (1..20)read-writecurrent
rldot1dStpBpduCount
OBJECT-TYPE
The number of bpdu that need to received for the link to be considered stable.
1.3.6.1.4.1.9.6.1.101.57.2.11INTEGER (1..60)read-writecurrent
rldot1dStpLastChanged
OBJECT-TYPE
The last time any object in this table was changed by SNMP or other local management means.
1.3.6.1.4.1.9.6.1.101.57.2.12TimeTicksread-onlycurrent
rldot1dStpPortTable
OBJECT-TYPE
A table that contains extended pair port specific information.
1.3.6.1.4.1.9.6.1.101.57.2.13not-accessiblecurrent
rldot1dStpPortEntry
OBJECT-TYPE
A list of information maintained by every port about the Spanning Tree Protocol state for that port.
1.3.6.1.4.1.9.6.1.101.57.2.13.1not-accessiblecurrent
rldot1dStpPortPort
OBJECT-TYPE
The port number of the port for which this entry contains Spanning Tree Protocol management information.
1.3.6.1.4.1.9.6.1.101.57.2.13.1.1INTEGER (1..4096)read-onlycurrent
rldot1dStpPortDampEnable
OBJECT-TYPE
Specified if dampening is enabled on this port.
1.3.6.1.4.1.9.6.1.101.57.2.13.1.2TruthValueread-writecurrent
rldot1dStpPortDampStable
OBJECT-TYPE
Specified if the port is stable.
1.3.6.1.4.1.9.6.1.101.57.2.13.1.3TruthValueread-onlycurrent
rldot1dStpPortFilterBpdu
OBJECT-TYPE
Specified if this port should filter bpdus when stp is disabled.
1.3.6.1.4.1.9.6.1.101.57.2.13.1.4INTEGER {false(0), true(1), none(2)}read-writecurrent
rldot1dStpPortBpduSent
OBJECT-TYPE
Specified the number of bpdu sent from this port.
1.3.6.1.4.1.9.6.1.101.57.2.13.1.5Counter32read-onlycurrent
rldot1dStpPortBpduReceived
OBJECT-TYPE
Specified the number of bpdu received in this port.
1.3.6.1.4.1.9.6.1.101.57.2.13.1.6Counter32read-onlycurrent
rldot1dStpPortRole
OBJECT-TYPE
Specified the role of this this port.
1.3.6.1.4.1.9.6.1.101.57.2.13.1.7INTEGER {unknown(0), disabled(1), alternate(2), backup(3), root(4), designated(5)}read-onlycurrent
rldot1dStpBpduType
OBJECT-TYPE
Specified the type of BPDU transmitted by this port.
1.3.6.1.4.1.9.6.1.101.57.2.13.1.8INTEGER {stp(0), rstp(1)}read-onlycurrent
rldot1dStpPortRestrictedRole
OBJECT-TYPE
If TRUE causes the Port not to be selected as Root Port for the CIST or any MSTI, even if it has the best spanning tree priority vector. Such a Port will be selected as an Alternate Port after the Root Port has been selected.
1.3.6.1.4.1.9.6.1.101.57.2.13.1.9TruthValueread-writecurrent
rldot1dStpPortAutoEdgePort
OBJECT-TYPE
If TRUE causes the Port when become up, to enter the blocking state, and if during 3 seconds it doesn't receive a BPDU, it will enter the forwarding state.
1.3.6.1.4.1.9.6.1.101.57.2.13.1.10TruthValueread-writecurrent
rldot1dStpPortLoopback
OBJECT-TYPE
Specified loopback was detected on port. Usable for only a short period of time if stp loopback guard is enabled (since port enters into shutdown state).
1.3.6.1.4.1.9.6.1.101.57.2.13.1.11TruthValueread-onlycurrent
rldot1dStpPortBpduOperStatus
OBJECT-TYPE
Specified BPDU handling operative status for port.
1.3.6.1.4.1.9.6.1.101.57.2.13.1.12INTEGER {filter(0), flood(1), bridge(2), stp(3)}read-onlycurrent
rldot1dStpPortTcnGuardEnable
OBJECT-TYPE
Enable / Disable TCN guard on port. TCN guard prevents receiving topology change notifications.
1.3.6.1.4.1.9.6.1.101.57.2.13.1.13TruthValueread-writecurrent
rldot1dStpPortsEnable
OBJECT-TYPE
Enable / Disable spanning tree on ports by default .
1.3.6.1.4.1.9.6.1.101.57.2.14TruthValueread-onlycurrent
rldot1dStpTaggedFlooding
OBJECT-TYPE
flooding can be done in tagged bpdu .
1.3.6.1.4.1.9.6.1.101.57.2.15TruthValueread-onlycurrent
rldot1dStpPortBelongToVlanDefault
OBJECT-TYPE
The default value of rldot1dStpPortMustBelongToVlan .
1.3.6.1.4.1.9.6.1.101.57.2.16TruthValueread-onlycurrent
rldot1dStpEnableByDefault
OBJECT-TYPE
The default value of rldot1dStpEnable .
1.3.6.1.4.1.9.6.1.101.57.2.17TruthValueread-onlycurrent
rldot1dStpPortToDefault
OBJECT-TYPE
To order port/s to revert to default setings .
1.3.6.1.4.1.9.6.1.101.57.2.18INTEGERread-writecurrent
rldot1dStpSupportedType
OBJECT-TYPE
The type of stp supported by the device.
1.3.6.1.4.1.9.6.1.101.57.2.19INTEGER {perDevice(1), perVlan(2), mstp(3)}read-onlycurrent
rldot1dStpEdgeportSupportInStp
OBJECT-TYPE
If EdgePort is supported in stpCompatible mode .
1.3.6.1.4.1.9.6.1.101.57.2.20TruthValueread-onlycurrent
rldot1dStpFilterBpdu
OBJECT-TYPE
Specified if the device should filter BPDUs when STP is disabled.
1.3.6.1.4.1.9.6.1.101.57.2.21TruthValueread-writecurrent
rldot1dStpFloodBpduMethod
OBJECT-TYPE
Specified flooding method: 1 - classic - untagged to all stp disabled ports 2 - bridging -normal bridging.
1.3.6.1.4.1.9.6.1.101.57.2.22INTEGER {classic(0), bridging(1)}read-writecurrent
rldot1dStpSeparatedBridges
OBJECT-IDENTITY
1.3.6.1.4.1.9.6.1.101.57.2.23
rldot1dStpSeparatedBridgesTable
OBJECT-TYPE
Define if separated bridges feature is enabled for each interface.
1.3.6.1.4.1.9.6.1.101.57.2.23.1not-accessiblecurrent
rldot1dStpSeparatedBridgesEntry
OBJECT-TYPE
Defines the contents of each line in the rlSeparatedBridgesTable table.
1.3.6.1.4.1.9.6.1.101.57.2.23.1.1not-accessiblecurrent
rldot1dStpSeparatedBridgesPortEnable
OBJECT-TYPE
This variable indicates whether the separated bridge feature is enabled on a specified ifIndex.
1.3.6.1.4.1.9.6.1.101.57.2.23.1.1.1TruthValueread-writecurrent
rldot1dStpSeparatedBridgesEnable
OBJECT-TYPE
Enable / Disable Separated Bridges Feature.
1.3.6.1.4.1.9.6.1.101.57.2.23.2TruthValueread-writecurrent
rldot1dStpSeparatedBridgesAutoConfig
OBJECT-TYPE
Enable / Disable Separated Bridges Automatic Configuration.
1.3.6.1.4.1.9.6.1.101.57.2.23.3TruthValueread-writecurrent
rldot1dStpPortBpduGuardTable
OBJECT-TYPE
A table that contains for each port whether it is bpdu guard .
1.3.6.1.4.1.9.6.1.101.57.2.24not-accessiblecurrent
rldot1dStpPortBpduGuardEntry
OBJECT-TYPE
A list of information maintained by every port whether it is bpdu guard.
1.3.6.1.4.1.9.6.1.101.57.2.24.1not-accessiblecurrent
rldot1dStpPortBpduGuardEnable
OBJECT-TYPE
Specified if bpdu guard is enabled on this port.
1.3.6.1.4.1.9.6.1.101.57.2.24.1.1TruthValueread-writecurrent
rldot1dStpLoopbackGuardEnable
OBJECT-TYPE
Define if STP loopback guard feature is globally enabled.
1.3.6.1.4.1.9.6.1.101.57.2.25TruthValueread-writecurrent
rldot1dStpDisabledPortStateTable
OBJECT-TYPE
Define stp port state for each stp disabled interface. This is auxiliary MIB emulates stp enabled port behaviour in ASIC for stp disabled port. The MIB contains only stp disabled ports entries
1.3.6.1.4.1.9.6.1.101.57.2.26not-accessiblecurrent
rldot1dStpDisabledPortStateEntry
OBJECT-TYPE
Defines the contents of each line in the rldot1dStpDisabledPortStateTable table.
1.3.6.1.4.1.9.6.1.101.57.2.26.1not-accessiblecurrent
rldot1dStpDisabledPortState
OBJECT-TYPE
The port's stp state as defined by external application . This state controls what action a port takes on reception of a frame.
1.3.6.1.4.1.9.6.1.101.57.2.26.1.1INTEGER {blocking(2), listening(3), learning(4), forwarding(5)}read-writecurrent
rldot1dStpClearPortCounters
OBJECT-TYPE
Clear the number of bpdu sent and recieved on specific port, if Value of 0 is specified then clear counters action is applied to all ports, this object behaviors is write-only, when reading this object it will always return 0.
1.3.6.1.4.1.9.6.1.101.57.2.27InterfaceIndexOrZeroread-writecurrent
rldot1dExtBase
OBJECT-IDENTITY
1.3.6.1.4.1.9.6.1.101.57.3
rldot1dExtBaseMibVersion
OBJECT-TYPE
MIB's version, the current version is 1.
1.3.6.1.4.1.9.6.1.101.57.3.1INTEGERread-onlycurrent
rldot1dDeviceCapabilities
OBJECT-TYPE
Indicates the optional parts of private extension of IEEE 802.1D and 802.1Q that are implemented by this device and are manageable through this MIB. Capabilities that are allowed on a per-port basis are indicated in dot1dPortCapabilities.
1.3.6.1.4.1.9.6.1.101.57.3.2OCTET STRING (SIZE(1))read-onlycurrent
rldot1wRStp
OBJECT-IDENTITY
1.3.6.1.4.1.9.6.1.101.57.4
rldot1wRStpVlanEdgePortTable
OBJECT-TYPE
A table that contains pair <vlan, port> specific information for the Rapid Spanning Tree Protocol.
1.3.6.1.4.1.9.6.1.101.57.4.1not-accessiblecurrent
rldot1wRStpVlanEdgePortEntry
OBJECT-TYPE
A list of information maintained by every pair <vlan, port> about the RAPID Spanning Tree Protocol state for that pair.
1.3.6.1.4.1.9.6.1.101.57.4.1.1not-accessiblecurrent
rldot1wRStpVlanEdgePortVlan
OBJECT-TYPE
The Vlan number that the port belongs to, and for which this entry contains Spanning Tree Protocol management information, If STP per device then only one value of 1 is allowed. If STP per a VLAN then all value of 1..4095 are allowed.
1.3.6.1.4.1.9.6.1.101.57.4.1.1.1INTEGER (1..4095)read-onlycurrent
rldot1wRStpVlanEdgePortPort
OBJECT-TYPE
The port number of the port for which this entry contains Spanning Tree Protocol management information.
1.3.6.1.4.1.9.6.1.101.57.4.1.1.2INTEGERread-onlycurrent
rldot1wRStpEdgePortStatus
OBJECT-TYPE
Specifies whether this port is an Edge Port or not
1.3.6.1.4.1.9.6.1.101.57.4.1.1.3TruthValueread-writecurrent
rldot1wRStpForceVersionTable
OBJECT-TYPE
A table that contains <vlan> specific information for the Rapid Spanning Tree Protocol.
1.3.6.1.4.1.9.6.1.101.57.4.2not-accessiblecurrent
rldot1wRStpForceVersionEntry
OBJECT-TYPE
A list of information maintained by every <vlan> about the RAPID Spanning Tree Protocol state for that pair.
1.3.6.1.4.1.9.6.1.101.57.4.2.1not-accessiblecurrent
rldot1wRStpForceVersionVlan
OBJECT-TYPE
The Vlan number that the port belongs to, and for which this entry contains Spanning Tree Protocol management information, If STP per device then only one value of 1 is allowed. If STP per a VLAN then all value of 1..4095 are allowed.
1.3.6.1.4.1.9.6.1.101.57.4.2.1.1INTEGER (1..4095)read-onlycurrent
rldot1wRStpForceVersionState
OBJECT-TYPE
Specifies whether this Bridge uses the normal RSTP algorithm, or STP Compatibility algorythm: 0 - STP Compatibility 2 - Normal RSTP
1.3.6.1.4.1.9.6.1.101.57.4.2.1.2INTEGERread-writecurrent
rldot1pPriorityMap
OBJECT-IDENTITY
1.3.6.1.4.1.9.6.1.101.57.5
rldot1pPriorityMapState
OBJECT-TYPE
enable / disable
1.3.6.1.4.1.9.6.1.101.57.5.1INTEGER {enable(1), disable(2)}read-writecurrent
rldot1pPriorityMapTable
OBJECT-TYPE
This table hold information the priority maps
1.3.6.1.4.1.9.6.1.101.57.5.2not-accessiblecurrent
rldot1pPriorityMapEntry
OBJECT-TYPE
The row definition for this table.
1.3.6.1.4.1.9.6.1.101.57.5.2.1not-accessiblecurrent
rldot1pPriorityMapName
OBJECT-TYPE
The map name
1.3.6.1.4.1.9.6.1.101.57.5.2.1.1DisplayString (SIZE(1..25))read-onlycurrent
rldot1pPriorityMapPriority
OBJECT-TYPE
The map holding the queue
1.3.6.1.4.1.9.6.1.101.57.5.2.1.2OCTET STRING (SIZE(8))read-createcurrent
rldot1pPriorityMapPort
OBJECT-TYPE
the port that the map, is applied on in config
1.3.6.1.4.1.9.6.1.101.57.5.2.1.3PortListread-createcurrent
rldot1pPriorityMapPortList
OBJECT-TYPE
the ports that the map, is applied on in actual
1.3.6.1.4.1.9.6.1.101.57.5.2.1.4PortListread-onlycurrent
rldot1pPriorityMapStatus
OBJECT-TYPE
The status of the table entry. It's used to delete an entry
1.3.6.1.4.1.9.6.1.101.57.5.2.1.5RowStatusread-createcurrent
rldot1sMstp
OBJECT-IDENTITY
1.3.6.1.4.1.9.6.1.101.57.6
rldot1sMstpInstanceTable
OBJECT-TYPE
A table that contains Mstp instance specific information for the Multiple Spanning Tree Protocol.
1.3.6.1.4.1.9.6.1.101.57.6.1not-accessiblecurrent
rldot1sMstpInstanceEntry
OBJECT-TYPE
A list of information maintained by every instance about the multiple Spanning Tree Protocol state for that instance.
1.3.6.1.4.1.9.6.1.101.57.6.1.1not-accessiblecurrent
rldot1sMstpInstanceId
OBJECT-TYPE
The Instance index.
1.3.6.1.4.1.9.6.1.101.57.6.1.1.1INTEGER (1..4094)read-onlycurrent
rldot1sMstpInstanceEnable
OBJECT-TYPE
Specifies whether this Instance is STP enable or disable
1.3.6.1.4.1.9.6.1.101.57.6.1.1.2TruthValueread-onlycurrent
rldot1sMstpInstanceTimeSinceTopologyChange
OBJECT-TYPE
The time (in hundredths of a second) since the last time a topology change was detected by the Mstp Instance .
1.3.6.1.4.1.9.6.1.101.57.6.1.1.3TimeTicksread-onlycurrent
rldot1sMstpInstanceTopChanges
OBJECT-TYPE
The total number of topology changes detected by this Instance since the management entity was last reset or initialized.
1.3.6.1.4.1.9.6.1.101.57.6.1.1.4Counterread-onlycurrent
rldot1sMstpInstanceDesignatedRoot
OBJECT-TYPE
The bridge identifier of the root of the spanning tree as determined by the Muliple Spanning Tree Protocol as executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node.
1.3.6.1.4.1.9.6.1.101.57.6.1.1.5BridgeIdread-onlycurrent
rldot1sMstpInstanceRootCost
OBJECT-TYPE
The cost of the path to the root as seen from this bridge.
1.3.6.1.4.1.9.6.1.101.57.6.1.1.6INTEGERread-onlycurrent
rldot1sMstpInstanceRootPort
OBJECT-TYPE
The port number of the port which offers the lowest cost path from this bridge to the root bridge.
1.3.6.1.4.1.9.6.1.101.57.6.1.1.7INTEGERread-onlycurrent
rldot1sMstpInstanceMaxAge
OBJECT-TYPE
The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.
1.3.6.1.4.1.9.6.1.101.57.6.1.1.8Timeoutread-onlycurrent
rldot1sMstpInstanceHelloTime
OBJECT-TYPE
The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using.
1.3.6.1.4.1.9.6.1.101.57.6.1.1.9Timeoutread-onlycurrent
rldot1sMstpInstanceHoldTime
OBJECT-TYPE
This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second.
1.3.6.1.4.1.9.6.1.101.57.6.1.1.10INTEGERread-onlycurrent
rldot1sMstpInstanceForwardDelay
OBJECT-TYPE
This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. [Note that this value is the one that this bridge is currently using, in contrast to dot1dStpBridgeForwardDelay which is the value that this bridge and all others would start using if/when this bridge were to become the root.]
1.3.6.1.4.1.9.6.1.101.57.6.1.1.11Timeoutread-onlycurrent
rldot1sMstpInstancePriority
OBJECT-TYPE
The value of the write-able portion of the Bridge ID, i.e., the first four bits of the first octet of the (8 octet long) Bridge ID.The value is a product of 4096. The next 12 bit are the msti id . The other (last) 6 octets of the Bridge ID are given by the value of dot1dBaseBridgeAddress.
1.3.6.1.4.1.9.6.1.101.57.6.1.1.12INTEGER (0..61440)read-writecurrent
rldot1sMstpInstanceRemainingHopes
OBJECT-TYPE
This count value determines the amount of hopes the information transmited by this bridge on this instance can travel.
1.3.6.1.4.1.9.6.1.101.57.6.1.1.13INTEGERread-onlycurrent
rldot1sMstpInstanceSwId
OBJECT-TYPE
The logical Instance Id which is binded for this entry from rldot1sMstpSwInstanceTable.
1.3.6.1.4.1.9.6.1.101.57.6.1.1.14INTEGERread-onlycurrent
rldot1sMstpInstancePortTable
OBJECT-TYPE
A table that contains pair <msti, port> specific information for the Spanning Tree Protocol.
1.3.6.1.4.1.9.6.1.101.57.6.2not-accessiblecurrent
rldot1sMstpInstancePortEntry
OBJECT-TYPE
A list of information maintained by every pair <msti, port> about the Spanning Tree Protocol state for that pair.
1.3.6.1.4.1.9.6.1.101.57.6.2.1not-accessiblecurrent
rldot1sMstpInstancePortMstiId
OBJECT-TYPE
The Vlan group number that the port belongs to, and for which this entry contains Spanning Tree Protocol management information.
1.3.6.1.4.1.9.6.1.101.57.6.2.1.1INTEGER (1..4094)read-onlycurrent
rldot1sMstpInstancePortPort
OBJECT-TYPE
The port number of the port for which this entry contains Spanning Tree Protocol management information.
1.3.6.1.4.1.9.6.1.101.57.6.2.1.2INTEGER (1..4096)read-onlycurrent
rldot1sMstpInstancePortPriority
OBJECT-TYPE
The value of the priority field which is contained in the more significant 4 bits of the most significant octet of the (2 octet long) Port ID. The value is a product of 16. The other octet of the Port ID is given by the value of rldot1dStpVlanGroupPort.
1.3.6.1.4.1.9.6.1.101.57.6.2.1.3INTEGER (0..240)read-writecurrent
rldot1sMstpInstancePortState
OBJECT-TYPE
The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning it will place that port into the broken(6) state. For ports which are disabled (see dot1dStpVlanPortEnable), this object will have a value of disabled(1).
1.3.6.1.4.1.9.6.1.101.57.6.2.1.4INTEGER {disabled(1), blocking(2), listening(3), learning(4), forwarding(5), broken(6)}read-onlycurrent
rldot1sMstpInstancePortEnable
OBJECT-TYPE
The enabled/disabled status of the port.
1.3.6.1.4.1.9.6.1.101.57.6.2.1.5INTEGER {enabled(1), disabled(2)}read-onlycurrent
rldot1sMstpInstancePortPathCost
OBJECT-TYPE
The contribution of this port to the path cost of paths towards the spanning tree root which include this port. 802.1D-1990 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN.
1.3.6.1.4.1.9.6.1.101.57.6.2.1.6INTEGER (1..200000000)read-onlycurrent
rldot1sMstpInstancePortDesignatedRoot
OBJECT-TYPE
The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached.
1.3.6.1.4.1.9.6.1.101.57.6.2.1.7BridgeIdread-onlycurrent
rldot1sMstpInstancePortDesignatedCost
OBJECT-TYPE
The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs.
1.3.6.1.4.1.9.6.1.101.57.6.2.1.8INTEGERread-onlycurrent
rldot1sMstpInstancePortDesignatedBridge
OBJECT-TYPE
The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment.
1.3.6.1.4.1.9.6.1.101.57.6.2.1.9BridgeIdread-onlycurrent
rldot1sMstpInstancePortDesignatedPort
OBJECT-TYPE
The Port Identifier of the port on the Designated Bridge for this port's segment.
1.3.6.1.4.1.9.6.1.101.57.6.2.1.10OCTET STRING (SIZE(2))read-onlycurrent
rldot1sMstpInstancePortForwardTransitions
OBJECT-TYPE
The number of times this port has transitioned from the Learning state to the Forwarding state.
1.3.6.1.4.1.9.6.1.101.57.6.2.1.11Counterread-onlycurrent
rldot1sMStpInstancePortAdminPathCost
OBJECT-TYPE
The administratively assigned value for the contribution of this port to the path cost of paths towards the spanning tree root. Writing a value of '0' assigns the automatically calculated default Path Cost value to the port. If the default Path Cost is being used, this object returns '0' when read. This complements the object dot1dStpPortPathCost, which returns the operational value of the path cost.
1.3.6.1.4.1.9.6.1.101.57.6.2.1.12INTEGER (0..200000000)read-writecurrent
rldot1sMStpInstancePortRole
OBJECT-TYPE
Specify the role of this this port.
1.3.6.1.4.1.9.6.1.101.57.6.2.1.13INTEGER {unknown(0), disabled(1), alternate(2), backup(3), root(4), designated(5), master(6)}read-onlycurrent
rldot1sMstpMaxHopes
OBJECT-TYPE
Max number of hopes that an MST BPDU will travel inside a region.
1.3.6.1.4.1.9.6.1.101.57.6.3INTEGER (1..40)read-writecurrent
rldot1sMstpConfigurationName
OBJECT-TYPE
The active configuration name as will be caried in MST BPDU's.
1.3.6.1.4.1.9.6.1.101.57.6.4SnmpAdminStringread-onlycurrent
rldot1sMstpRevisionLevel
OBJECT-TYPE
The active revision level.
1.3.6.1.4.1.9.6.1.101.57.6.5INTEGER (0..65535)read-onlycurrent
rldot1sMstpVlanTable
OBJECT-TYPE
A table that contains information about the alocation of vlans to groups.
1.3.6.1.4.1.9.6.1.101.57.6.6not-accessiblecurrent
rldot1sMstpVlanEntry
OBJECT-TYPE
A list of information maintained by every vlan about the group it belongs to.
1.3.6.1.4.1.9.6.1.101.57.6.6.1not-accessiblecurrent
rldot1sMstpVlan
OBJECT-TYPE
The vlan number of the vlan for which this entry contains Spanning Tree Protocol management information.
1.3.6.1.4.1.9.6.1.101.57.6.6.1.1INTEGER (1..4094)read-onlycurrent
rldot1sMstpGroup
OBJECT-TYPE
Specifid the active group number this vlan belonges to.
1.3.6.1.4.1.9.6.1.101.57.6.6.1.2INTEGER (0..4094)read-onlycurrent
rldot1sMstpPendingGroup
OBJECT-TYPE
Specifid the pending group number this vlan belonges to.
1.3.6.1.4.1.9.6.1.101.57.6.6.1.3INTEGER (0..4094)read-writecurrent
rldot1sMstpExtPortTable
OBJECT-TYPE
A table that contains MSTP information about ports of the CIST.
1.3.6.1.4.1.9.6.1.101.57.6.7not-accessiblecurrent
rldot1sMstpExtPortEntry
OBJECT-TYPE
A list of information maintained by every port of the CIST.
1.3.6.1.4.1.9.6.1.101.57.6.7.1not-accessiblecurrent
rldot1sMstpExtPortPort
OBJECT-TYPE
The port number of the port for which this entry contains Spanning Tree Protocol management information.
1.3.6.1.4.1.9.6.1.101.57.6.7.1.1INTEGER (1..4096)read-onlycurrent
rldot1sMstpExtPortInternalOperPathCost
OBJECT-TYPE
The contribution of this port to the path cost of paths towards the spanning tree regional root which include this port. 802.1S-2002 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN.
1.3.6.1.4.1.9.6.1.101.57.6.7.1.2INTEGER (1..200000000)read-onlycurrent
rldot1sMstpExtPortDesignatedRegionalRoot
OBJECT-TYPE
The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached.
1.3.6.1.4.1.9.6.1.101.57.6.7.1.3BridgeIdread-onlycurrent
rldot1sMstpExtPortDesignatedRegionalCost
OBJECT-TYPE
The regional path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs.
1.3.6.1.4.1.9.6.1.101.57.6.7.1.4INTEGERread-onlycurrent
rldot1sMstpExtPortBoundary
OBJECT-TYPE
Indication if the port is conented to to a lan segment outside or inside the region.
1.3.6.1.4.1.9.6.1.101.57.6.7.1.5TruthValueread-onlycurrent
rldot1sMstpExtPortInternalAdminPathCost
OBJECT-TYPE
The administratively assigned value for the contribution of this port to the path cost of paths towards the spanning tree root. Writing a value of '0' assigns the automatically calculated default Path Cost value to the port. If the default Path Cost is being used, this object returns '0' when read. This complements the object dot1dStpPortPathCost, which returns the operational value of the path cost.
1.3.6.1.4.1.9.6.1.101.57.6.7.1.6INTEGER (0..200000000)read-writecurrent
rldot1sMstpDesignatedMaxHopes
OBJECT-TYPE
Max number of hopes that an MST BPDU will travel inside a region.
1.3.6.1.4.1.9.6.1.101.57.6.8INTEGER (1..40)read-onlycurrent
rldot1sMstpRegionalRoot
OBJECT-TYPE
CIST Regional Root Identifier (13.16.4). The Bridge Identifier of the current CIST Regional Root.
1.3.6.1.4.1.9.6.1.101.57.6.9BridgeIdread-onlycurrent
rldot1sMstpRegionalRootCost
OBJECT-TYPE
The CIST path cost from the transmitting Bridge to the CIST Regional Root.
1.3.6.1.4.1.9.6.1.101.57.6.10INTEGERread-onlycurrent
rldot1sMstpPendingConfigurationName
OBJECT-TYPE
The pending configuration name.
1.3.6.1.4.1.9.6.1.101.57.6.11SnmpAdminString (SIZE(1..32))read-writecurrent
rldot1sMstpPendingRevisionLevel
OBJECT-TYPE
The pending revision level.
1.3.6.1.4.1.9.6.1.101.57.6.12INTEGER (0..65535)read-writecurrent
rldot1sMstpPendingAction
OBJECT-TYPE
The action to be done with the pending configuration. copyPendingActive - to copy the pending mst configuration to the active one. copyActivePending - to copy the active mst configuration to the pending one.
1.3.6.1.4.1.9.6.1.101.57.6.13INTEGER {copyPendingActive(1), copyActivePending(2)}read-writecurrent
rldot1sMstpRemainingHops
OBJECT-TYPE
This count value determines the amount of hops the information transmitted by this bridge can travel.
1.3.6.1.4.1.9.6.1.101.57.6.14INTEGERread-onlycurrent
rldot1sMstpInstanceVlanTable
OBJECT-TYPE
This table contains vlan lists per MSTP instances.
1.3.6.1.4.1.9.6.1.101.57.6.15not-accessiblecurrent
rldot1sMstpInstanceVlanEntry
OBJECT-TYPE
The entry contains vlan lists per specific MSTP instance.
1.3.6.1.4.1.9.6.1.101.57.6.15.1not-accessiblecurrent
rldot1sMstpInstanceVlanId
OBJECT-TYPE
Specifiy the instance number.
1.3.6.1.4.1.9.6.1.101.57.6.15.1.1INTEGER (0..4094)read-onlycurrent
rldot1sMstpInstanceVlanDbType
OBJECT-TYPE
Specifiy which data-base to access: active or pending.
1.3.6.1.4.1.9.6.1.101.57.6.15.1.2INTEGER {active(1), pending(2)}read-onlycurrent
rldot1sMstpInstanceVlanId1To1024
OBJECT-TYPE
first VlanId List of specific MSTP instance.
1.3.6.1.4.1.9.6.1.101.57.6.15.1.3VlanList1read-onlycurrent
rldot1sMstpInstanceVlanId1025To2048
OBJECT-TYPE
second VlanId List of specific MSTP instance.
1.3.6.1.4.1.9.6.1.101.57.6.15.1.4VlanList2read-onlycurrent
rldot1sMstpInstanceVlanId2049To3072
OBJECT-TYPE
third VlanId List of specific MSTP instance.
1.3.6.1.4.1.9.6.1.101.57.6.15.1.5VlanList3read-onlycurrent
rldot1sMstpInstanceVlanId3073To4094
OBJECT-TYPE
fourth VlanId List of specific MSTP instance.
1.3.6.1.4.1.9.6.1.101.57.6.15.1.6VlanList4read-onlycurrent
rldot1sMstpConfigurationDigest
OBJECT-TYPE
The active configuration digest.
1.3.6.1.4.1.9.6.1.101.57.6.16OCTET STRING (SIZE(16))read-onlycurrent
rldot1sMstpPendingConfigurationDigest
OBJECT-TYPE
The pending configuration digest.
1.3.6.1.4.1.9.6.1.101.57.6.17OCTET STRING (SIZE(16))read-onlycurrent
rldot1sMstpSwInstanceTable
OBJECT-TYPE
This table contains logical instance to rldot1sMstpInstanceId mapping.
1.3.6.1.4.1.9.6.1.101.57.6.18not-accessiblecurrent
rldot1sMstpSwInstanceEntry
OBJECT-TYPE
The entry contains logical instance information.
1.3.6.1.4.1.9.6.1.101.57.6.18.1not-accessiblecurrent
rldot1sMstpSwInstanceSwId
OBJECT-TYPE
The STP Instance logical index.
1.3.6.1.4.1.9.6.1.101.57.6.18.1.1INTEGER (1..4094)read-onlycurrent
rldot1sMstpSwInstanceId
OBJECT-TYPE
The STP Instance index rldot1sMstpInstanceId which exist at rldot1sMstpInstanceTable.
1.3.6.1.4.1.9.6.1.101.57.6.18.1.2INTEGER (1..64)read-onlycurrent
rldot1sMstpSwInstanceStatus
OBJECT-TYPE
The status of the entry, used to add, delete or update an entry
1.3.6.1.4.1.9.6.1.101.57.6.18.1.3RowStatusread-createcurrent
rldot1dTpAgingTime
OBJECT-IDENTITY
1.3.6.1.4.1.9.6.1.101.57.7
rldot1dTpAgingTimeMin
OBJECT-TYPE
The min timeout period in seconds for aging out dynamically learned forwarding information.
1.3.6.1.4.1.9.6.1.101.57.7.1INTEGERread-onlycurrent
rldot1dTpAgingTimeMax
OBJECT-TYPE
The max timeout period in seconds for aging out dynamically learned forwarding information.
1.3.6.1.4.1.9.6.1.101.57.7.2INTEGERread-onlycurrent
rlBrgPvst
OBJECT-IDENTITY
1.3.6.1.4.1.9.6.1.101.57.9
rlBrgPvstVlanTable
OBJECT-TYPE
This table contains Per Vlan Spanning-Tree vlan configuration.
1.3.6.1.4.1.9.6.1.101.57.9.1not-accessiblecurrent
rlBrgPvstVlanEntry
OBJECT-TYPE
The entry contains PVST configuration per specific Vlan.
1.3.6.1.4.1.9.6.1.101.57.9.1.1not-accessiblecurrent
rlBrgPvstVlanId
OBJECT-TYPE
The Vlan number for this entry which contains PVST configuration.
1.3.6.1.4.1.9.6.1.101.57.9.1.1.1INTEGER (1..4094)read-onlycurrent
rlBrgPvstVlanHelloTime
OBJECT-TYPE
The time intervals in seconds for the transmission of Configuration PVST bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so. When configuring the Hello time, the following relationship should be maintained: Max-Age >= 2*(Hello-Time + 1).
1.3.6.1.4.1.9.6.1.101.57.9.1.1.2INTEGER (1..10)read-writecurrent
rlBrgPvstVlanForwardDelay
OBJECT-TYPE
The time interval in seconds, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. When configuring the forwarding time, the following relationship should be maintained: 2*(Forward-Time - 1) >= Max-Age.
1.3.6.1.4.1.9.6.1.101.57.9.1.1.3INTEGER (4..30)read-writecurrent
rlBrgPvstVlanMaxAge
OBJECT-TYPE
The maximum age time in seconds of PVST Protocol information learned from the network on any port before it is discarded. When configuring the maximum age, the following relationships should be maintained: 2*(Forward-Time - 1) >= Max-Age Max-Age >= 2*(Hello-Time + 1).
1.3.6.1.4.1.9.6.1.101.57.9.1.1.4INTEGER (6..40)read-writecurrent
rlBrgPvstVlanPriority
OBJECT-TYPE
The value of the write-able portion of the Bridge ID, i.e., the first four bits of the first octet of the (8 octet long) Bridge ID. The value is a product of 4096.
1.3.6.1.4.1.9.6.1.101.57.9.1.1.5INTEGER (0..61440)read-writecurrent
rlBrgPvstVlanStatus
OBJECT-TYPE
The status of the table entry, used to add, delete or update an entry
1.3.6.1.4.1.9.6.1.101.57.9.1.1.6RowStatusread-createcurrent
rlBrgPvstOperVlanTable
OBJECT-TYPE
This table contains Per Vlan Spanning-Tree active vlan configuration.
1.3.6.1.4.1.9.6.1.101.57.9.2not-accessiblecurrent
rlBrgPvstOperVlanEntry
OBJECT-TYPE
The entry contains PVST active configuration per specific Vlan.
1.3.6.1.4.1.9.6.1.101.57.9.2.1not-accessiblecurrent
rlBrgPvstOperVlanId
OBJECT-TYPE
The Vlan number for this entry which contains PVST active configuration.
1.3.6.1.4.1.9.6.1.101.57.9.2.1.1INTEGERread-onlycurrent
rlBrgPvstOperVlanEnable
OBJECT-TYPE
Indicates whether this Vlan is enabled for PVST / RPVST.
1.3.6.1.4.1.9.6.1.101.57.9.2.1.2TruthValueread-onlycurrent
rlBrgPvstOperVlanTimeSinceTopologyChange
OBJECT-TYPE
The time (in miliseconds) since the last time a topology change was detected on current PVST Instance.
1.3.6.1.4.1.9.6.1.101.57.9.2.1.3TimeTicksread-onlycurrent
rlBrgPvstOperVlanTopChanges
OBJECT-TYPE
The total number of topology changes detected by this on current PVST Instance since the management entity was last reset or initialized.
1.3.6.1.4.1.9.6.1.101.57.9.2.1.4Counterread-onlycurrent
rlBrgPvstOperVlanDesignatedRoot
OBJECT-TYPE
The bridge identifier of the root of the spanning tree as determined by the PVST Spanning Tree Protocol as executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node.
1.3.6.1.4.1.9.6.1.101.57.9.2.1.5BridgeIdread-onlycurrent
rlBrgPvstOperVlanRootCost
OBJECT-TYPE
The cost of the path to the root as seen from current bridge on current vlan.
1.3.6.1.4.1.9.6.1.101.57.9.2.1.6INTEGERread-onlycurrent
rlBrgPvstOperVlanRootPort
OBJECT-TYPE
The port number of the port which offers the lowest cost path from this bridge to the root bridge.
1.3.6.1.4.1.9.6.1.101.57.9.2.1.7INTEGERread-onlycurrent
rlBrgPvstOperVlanRootMaxAge
OBJECT-TYPE
The rlBrgPvstVlanMaxAge which recieved from the root of current PVST instance.
1.3.6.1.4.1.9.6.1.101.57.9.2.1.8INTEGERread-onlycurrent
rlBrgPvstOperVlanRootHelloTime
OBJECT-TYPE
The rlBrgPvstVlanHelloTime which recieved from the root of current PVST instance.
1.3.6.1.4.1.9.6.1.101.57.9.2.1.9INTEGERread-onlycurrent
rlBrgPvstOperVlanRootForwardDelay
OBJECT-TYPE
The rlBrgPvstVlanForwardDelay which recieved from the root of current PVST instance.
1.3.6.1.4.1.9.6.1.101.57.9.2.1.10INTEGERread-onlycurrent
rlBrgPvstOperVlanMaxAge
OBJECT-TYPE
The operational maximum age time in seconds of PVST Protocol information learned from the network on any port before it is discarded. When configuring the maximum age, the following relationships should be maintained: 2*(Forward-Time - 1) >= Max-Age Max-Age >= 2*(Hello-Time + 1).
1.3.6.1.4.1.9.6.1.101.57.9.2.1.11INTEGERread-onlycurrent
rlBrgPvstOperVlanHelloTime
OBJECT-TYPE
The operational time intervals in seconds for the transmission of Configuration PVST bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so. When configuring the Hello time, the following relationship should be maintained: Max-Age >= 2*(Hello-Time + 1).
1.3.6.1.4.1.9.6.1.101.57.9.2.1.12INTEGERread-onlycurrent
rlBrgPvstOperVlanForwardDelay
OBJECT-TYPE
The operational time interval in seconds, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. When configuring the forwarding time, the following relationship should be maintained: 2*(Forward-Time - 1) >= Max-Age.
1.3.6.1.4.1.9.6.1.101.57.9.2.1.13INTEGERread-onlycurrent
rlBrgPvstOperVlanPriority
OBJECT-TYPE
The value of the write-able portion of the Bridge ID, i.e., the first four bits of the first octet of the (8 octet long) Bridge ID. The value is a product of 4096.
1.3.6.1.4.1.9.6.1.101.57.9.2.1.14INTEGERread-onlycurrent
rlBrgPvstPortTable
OBJECT-TYPE
This table contains Per Vlan Spanning-Tree Port configuration.
1.3.6.1.4.1.9.6.1.101.57.9.3not-accessiblecurrent
rlBrgPvstPortEntry
OBJECT-TYPE
The entry contains PVST configuration per specific Vlan and Port.
1.3.6.1.4.1.9.6.1.101.57.9.3.1not-accessiblecurrent
rlBrgPvstPortVlanId
OBJECT-TYPE
The Vlan number for this entry which contains PVST configuration.
1.3.6.1.4.1.9.6.1.101.57.9.3.1.1INTEGER (1..4094)read-onlycurrent
rlBrgPvstPortPort
OBJECT-TYPE
The port number of the port for which this entry contains Per Vlan Spanning Tree Protocol management information.
1.3.6.1.4.1.9.6.1.101.57.9.3.1.2INTEGER (1..4096)read-onlycurrent
rlBrgPvstPortPathCost
OBJECT-TYPE
The contribution of this port to the path cost of paths towards the spanning tree root which include this port. Writing a value of '0' assigns the automatically calculated default Path Cost value to the port. If the default Path Cost is being used, this object returns '0' when read. Default path cost is determined by port speed and path cost method (long or short).
1.3.6.1.4.1.9.6.1.101.57.9.3.1.3INTEGER (0..200000000)read-writecurrent
rlBrgPvstPortPriority
OBJECT-TYPE
The Admin value of the priority field which is contained in the more significant 4 bits of the most significant octet of the (2 octet long) Port ID. The other octet of the Port ID is given by the value of rlBrgPvstPortPort. The priority value must be a multiple of 16.
1.3.6.1.4.1.9.6.1.101.57.9.3.1.4INTEGER (0..240)read-writecurrent
rlBrgPvstPortStatus
OBJECT-TYPE
The status of the table entry, used to add, delete or update an entry
1.3.6.1.4.1.9.6.1.101.57.9.3.1.5RowStatusread-createcurrent
rlBrgPvstOperPortTable
OBJECT-TYPE
This table contains Per Vlan Spanning-Tree active Port configuration.
1.3.6.1.4.1.9.6.1.101.57.9.4not-accessiblecurrent
rlBrgPvstOperPortEntry
OBJECT-TYPE
The entry contains PVST active configuration per specific Vlan and Port.
1.3.6.1.4.1.9.6.1.101.57.9.4.1not-accessiblecurrent
rlBrgPvstOperPortVlanId
OBJECT-TYPE
The Vlan number for this entry which contains PVST configuration.
1.3.6.1.4.1.9.6.1.101.57.9.4.1.1INTEGERread-onlycurrent
rlBrgPvstOperPortPort
OBJECT-TYPE
The port number of the port for which this entry contains Per Vlan Spanning Tree Protocol management information.
1.3.6.1.4.1.9.6.1.101.57.9.4.1.2INTEGERread-onlycurrent
rlBrgPvstOperPortEnable
OBJECT-TYPE
The enabled/disabled status of the port.
1.3.6.1.4.1.9.6.1.101.57.9.4.1.3TruthValueread-onlycurrent
rlBrgPvstOperPortPathCost
OBJECT-TYPE
The Operational contribution of this port to the path cost of paths towards the spanning tree root which include this port. Default path cost is determined by port speed and path cost method (long or short).
1.3.6.1.4.1.9.6.1.101.57.9.4.1.4INTEGERread-onlycurrent
rlBrgPvstOperPortPriority
OBJECT-TYPE
The Operational value of the priority field which is contained in the more significant 4 bits of the most significant octet of the (2 octet long) Port ID. The other octet of the Port ID is given by the value of rlBrgPvstOperPortPort.
1.3.6.1.4.1.9.6.1.101.57.9.4.1.5INTEGERread-onlycurrent
rlBrgPvstOperPortState
OBJECT-TYPE
The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning it will place that port into the broken(6)state.
1.3.6.1.4.1.9.6.1.101.57.9.4.1.6INTEGER {disabled(1), blocking(2), listening(3), learning(4), forwarding(5), broken(6)}read-onlycurrent
rlBrgPvstOperPortRole
OBJECT-TYPE
Specify the STP role of this this port.
1.3.6.1.4.1.9.6.1.101.57.9.4.1.7INTEGER {unknown(0), disabled(1), alternate(2), backup(3), root(4), designated(5)}read-onlycurrent
rlBrgPvstOperPortBpduType
OBJECT-TYPE
Specified the type of BPDU transmitted by this port.
1.3.6.1.4.1.9.6.1.101.57.9.4.1.8INTEGER {pvst(2), rpvst(3)}read-onlycurrent
rlBrgPvstOperPortDesignatedRoot
OBJECT-TYPE
The bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node.
1.3.6.1.4.1.9.6.1.101.57.9.4.1.9BridgeIdread-onlycurrent
rlBrgPvstOperPortDesignatedCost
OBJECT-TYPE
The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs.
1.3.6.1.4.1.9.6.1.101.57.9.4.1.10INTEGERread-onlycurrent
rlBrgPvstOperPortDesignatedBridge
OBJECT-TYPE
The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment.
1.3.6.1.4.1.9.6.1.101.57.9.4.1.11BridgeIdread-onlycurrent
rlBrgPvstOperPortDesignatedPort
OBJECT-TYPE
The Port Identifier of the port on the Designated Bridge for this port's segment.
1.3.6.1.4.1.9.6.1.101.57.9.4.1.12OCTET STRING (SIZE(2))read-onlycurrent
rlBrgPvstOperPortForwardTransitions
OBJECT-TYPE
The number of times this port has transitioned from the Learning state to the Forwarding state.
1.3.6.1.4.1.9.6.1.101.57.9.4.1.13Counter32read-onlycurrent
rlBrgPvstOperPortEdgePort
OBJECT-TYPE
The operational value of the Edge Port parameter. The object is initialized to the value of dot1dStpPortAdminEdgePort and is set FALSE on reception of a BPDU.
1.3.6.1.4.1.9.6.1.101.57.9.4.1.14TruthValueread-onlycurrent
rlBrgPvstOperPortBpduSent
OBJECT-TYPE
Specified the number of bpdu sent from this port.
1.3.6.1.4.1.9.6.1.101.57.9.4.1.15Counter32read-onlycurrent
rlBrgPvstOperPortBpduReceived
OBJECT-TYPE
Specified the number of bpdu received in this port.
1.3.6.1.4.1.9.6.1.101.57.9.4.1.16Counter32read-onlycurrent
rlBrgPvstInconsistencyPortTable
OBJECT-TYPE
This table contains Per Vlan Spanning-Tree Ports Inconsistency information.
1.3.6.1.4.1.9.6.1.101.57.9.5not-accessiblecurrent
rlBrgPvstInconsistencyPortEntry
OBJECT-TYPE
Entry contains Per Vlan Spanning-Tree Port Inconsistency information.
1.3.6.1.4.1.9.6.1.101.57.9.5.1not-accessiblecurrent
rlBrgPvstInconsistencyVlanId
OBJECT-TYPE
The Vlan number for this entry which contains PVST Port Inconsistency information.
1.3.6.1.4.1.9.6.1.101.57.9.5.1.1INTEGER (1..4094)read-onlycurrent
rlBrgPvstInconsistencyPort
OBJECT-TYPE
The port number of the port for which this entry contains Per Vlan Spanning Tree Port Inconsistency information.
1.3.6.1.4.1.9.6.1.101.57.9.5.1.2INTEGER (1..4096)read-onlycurrent
rlBrgPvstInconsistencyState
OBJECT-TYPE
The port PVST Inconsistency state.
1.3.6.1.4.1.9.6.1.101.57.9.5.1.3Bits {type(0), pvid(1)}read-onlycurrent