ZYXEL-PRESTIGE-MIB
- Registered at
- 1.3.6.1.4.1.890.1.2.1.11.3.6.1.4.1.890.1.2.1.21.3.6.1.4.1.890.1.2.1.31.3.6.1.4.1.890.1.2.1.41.3.6.1.4.1.890.1.2.1.51.3.6.1.4.1.890.1.2.1.61.3.6.1.4.1.890.1.2.1.99
- Namespace
- zyxel
- Source file
ZYXEL-PRESTIGE-MIB- Digest
sha256:e2f7ed35e22e69c8366724aee6f119d72cc42db579b825fd599aad3ca37a432f
Imports
| From | Symbols |
|---|---|
| APPLETALK-MIB | atportIndex |
| IF-MIB | ifIndex |
| IP-MIB | ipAdEntAddr |
| RFC1213-MIB | egpNeighAddr, ipRouteDest |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP |
| SNMPv2-SMI | Counter32, Gauge32, IpAddress, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TRAP-TYPE, TimeTicks, enterprises, iso |
| SNMPv2-TC | DisplayString, PhysAddress, TEXTUAL-CONVENTION |
| ZYXEL-MIB | prestigeCommon |
Imported by
Nothing in this corpus imports this module.
Load order
Every file a consumer needs in order to load this module, dependencies first.
APPLETALK-MIB IANAifType-MIB IF-MIB INET-ADDRESS-MIB IP-MIB RFC1213-MIB SNMPv2-CONF SNMPv2-MIB SNMPv2-SMI SNMPv2-TC ZYXEL-MIB ZYXEL-PRESTIGE-MIB
Objects
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| prestigeSystem OBJECT-IDENTITY | 1.3.6.1.4.1.890.1.2.1.1 | |||
| sysRasFWVersion OBJECT-TYPE Current ras firmware version, N/A means information not available. | 1.3.6.1.4.1.890.1.2.1.1.1 | DisplayString | read-only | mandatory |
| sysHWVersion OBJECT-TYPE Current hardware version, N/A means information not available. | 1.3.6.1.4.1.890.1.2.1.1.2 | DisplayString | read-only | mandatory |
| sysModemVersion OBJECT-TYPE Current modem code version, N/A means information not available. | 1.3.6.1.4.1.890.1.2.1.1.3 | DisplayString | read-only | mandatory |
| sysSysName OBJECT-TYPE Choose a descriptive name for identification purposes. This name can be up to 30 alphanumeric characters long. Spaces are not allowed, but dashes '-' and underscores '_' are accepted. | 1.3.6.1.4.1.890.1.2.1.1.4 | DisplayString (SIZE(0..29)) | read-write | mandatory |
| sysLocation OBJECT-TYPE The geographic location (up to 30 characters) of your Prestige. | 1.3.6.1.4.1.890.1.2.1.1.5 | DisplayString (SIZE(0..29)) | read-write | mandatory |
| sysConatctPersion OBJECT-TYPE The name (up to 30 characters) of the person in charge of this Prestige. | 1.3.6.1.4.1.890.1.2.1.1.6 | DisplayString (SIZE(0..29)) | read-write | mandatory |
| sysProtocolRouteIp OBJECT-TYPE Set this object to Yes to enable IP routing. You must enable IP routing for Internet access. | 1.3.6.1.4.1.890.1.2.1.1.7 | INTEGER {other(1), yes(2), no(3)} | read-write | mandatory |
| sysProtocolBridge OBJECT-TYPE Turn on/off bridging for protocols not supported (e.g., SNA) or not turned on in the previous Route fields. | 1.3.6.1.4.1.890.1.2.1.1.8 | INTEGER {other(1), yes(2), no(3)} | read-write | mandatory |
| sysDomainName OBJECT-TYPE The domain name of the LAN. If this object is empty, the ISP may assign a domain name via DHCP. | 1.3.6.1.4.1.890.1.2.1.1.9 | DisplayString (SIZE(0..29)) | read-write | mandatory |
| sysReset OBJECT-TYPE If yes reset prestige. | 1.3.6.1.4.1.890.1.2.1.1.10 | INTEGER {other(1), yes(2), no(3)} | read-write | mandatory |
| prestigeDynDns OBJECT-IDENTITY | 1.3.6.1.4.1.890.1.2.1.2 | |||
| ddnsActiveStatus OBJECT-TYPE Enable or disable the Dynamic DNS service. | 1.3.6.1.4.1.890.1.2.1.2.1 | INTEGER {other(1), yes(2), no(3)} | read-write | mandatory |
| ddnsServiceProvider OBJECT-TYPE The choice of your dynamic DNS client. | 1.3.6.1.4.1.890.1.2.1.2.2 | INTEGER {other(1), dyndns(2)} | read-write | mandatory |
| ddnsHost OBJECT-TYPE The domain name assigned to your prestige by your Dyanmic DNS provider. | 1.3.6.1.4.1.890.1.2.1.2.3 | DisplayString (SIZE(0..29)) | read-write | mandatory |
| ddnsEmail OBJECT-TYPE Your e-mail address. | 1.3.6.1.4.1.890.1.2.1.2.4 | DisplayString (SIZE(0..29)) | read-write | mandatory |
| ddnsUser OBJECT-TYPE The user name assigned to you. | 1.3.6.1.4.1.890.1.2.1.2.5 | DisplayString (SIZE(0..29)) | read-write | mandatory |
| ddnsPassword OBJECT-TYPE The password assigned to you. | 1.3.6.1.4.1.890.1.2.1.2.6 | DisplayString (SIZE(0..29)) | read-write | mandatory |
| ddnsEnableWildcard OBJECT-TYPE Enabling the wildcard feature for your host causes *.yourhost.dyndns.org to be aliased to the same IP address as yourhost.dyndns.org. This feature is useful if you want to be able to use for example www.yourhost.dyndns.org and still reach your hostname. | 1.3.6.1.4.1.890.1.2.1.2.7 | INTEGER {other(1), yes(2), no(3)} | read-write | mandatory |
| prestigeLAN OBJECT-IDENTITY | 1.3.6.1.4.1.890.1.2.1.3 | |||
| lanFilter OBJECT-IDENTITY | 1.3.6.1.4.1.890.1.2.1.3.1 | |||
| inProtocolFilterSet OBJECT-TYPE This object specified the protocol filter set for incoming ethernet traffic. | 1.3.6.1.4.1.890.1.2.1.3.1.1 | DisplayString (SIZE(0..8)) | read-write | mandatory |
| inDeviceFilterSet OBJECT-TYPE This object specified the device filter set for incoming ethernet traffic. | 1.3.6.1.4.1.890.1.2.1.3.1.2 | DisplayString (SIZE(0..8)) | read-write | mandatory |
| outProtocolFilterSet OBJECT-TYPE This object specified the protocol filter set for outgoing ethernet traffic. | 1.3.6.1.4.1.890.1.2.1.3.1.3 | DisplayString (SIZE(0..8)) | read-write | mandatory |
| outDeviceFilterSet OBJECT-TYPE This object specified the device filter set for outgoing ethernet traffic. | 1.3.6.1.4.1.890.1.2.1.3.1.4 | DisplayString (SIZE(0..8)) | read-write | mandatory |
| lanDHCP OBJECT-IDENTITY | 1.3.6.1.4.1.890.1.2.1.3.2 | |||
| dhcpStatus OBJECT-TYPE If it is set to Server, your Prestige can assign IP addresses, an IP default gateway and DNS servers to Windows 95, Windows NT and other systems that support the DHCP client. If set to None, the DHCP server will be disabled. If set to Relay, the Prestige acts as a surrogate DHCP server and relays DHCP requests and responses between the remote server and the clients. Enter the IP address of the actual, remote DHCP server in the Remote DHCP Server in this case. | 1.3.6.1.4.1.890.1.2.1.3.2.1 | INTEGER {none(1), server(2), relay(3)} | read-write | mandatory |
| dhcpStartIpAddr OBJECT-TYPE This object specifies the first of the contiguous addresses in the IP address pool. | 1.3.6.1.4.1.890.1.2.1.3.2.2 | IpAddress | read-write | mandatory |
| dhcpPoolSize OBJECT-TYPE This object specifies the size, or count, of the IP address pool. | 1.3.6.1.4.1.890.1.2.1.3.2.3 | INTEGER | read-write | mandatory |
| dhcpPrimaryDnsServer OBJECT-TYPE The DNS server addresses that you enter in this object are passed to the client machines along with the assigned IP address and subnet mask. | 1.3.6.1.4.1.890.1.2.1.3.2.4 | IpAddress | read-write | mandatory |
| dhcpSecondaryDnsServer OBJECT-TYPE The DNS server addresses that you enter in this object are passed to the client machines along with the assigned IP address and subnet mask. | 1.3.6.1.4.1.890.1.2.1.3.2.5 | IpAddress | read-write | mandatory |
| dhcpRemoteDhcpServer OBJECT-TYPE If Relay is selected in the dhcpStatus pbject above, then this object should be the IP address of the actual, remote DHCP server. | 1.3.6.1.4.1.890.1.2.1.3.2.6 | IpAddress | read-write | mandatory |
| lanTcpIp OBJECT-IDENTITY | 1.3.6.1.4.1.890.1.2.1.3.3 | |||
| lanIpAddress OBJECT-TYPE IP address of your Prestige in dotted decimal notation | 1.3.6.1.4.1.890.1.2.1.3.3.1 | IpAddress | read-write | mandatory |
| lanIpSubnetMask OBJECT-TYPE The subnet mask specifies the network number portion of the LAN IP address. | 1.3.6.1.4.1.890.1.2.1.3.3.2 | IpAddress | read-write | mandatory |
| lanIpRipDirection OBJECT-TYPE RIP (Routing Information Protocol) allows a router to exchange routing information with other routers. This object controls the sending and receiving of RIP packets. When set to Both, the Prestige will broadcast its routing table periodically and incorporate the RIP information that it receives; when set to None, it will not send any RIP packets and will ignore any RIP packets received. | 1.3.6.1.4.1.890.1.2.1.3.3.3 | INTEGER {none(1), both(2), in(3), out(4)} | read-write | mandatory |
| lanIpRipVersion OBJECT-TYPE This object controls the format and the broadcasting method of the RIP packets that the Prestige sends (it recognizes both formats when receiving). RIP-1 is universally supported; but RIP-2 carries more information. RIP-1 is probably adequate for most networks, unless you have a unusual network topology. Both RIP-2B and RIP-2M sends the routing data in RIP-2 format; the difference being that RIP-2B uses subnet broadcasting while RIP-2M uses multicasting. | 1.3.6.1.4.1.890.1.2.1.3.3.4 | INTEGER {ohter(1), rip1(2), rip2B(3), rip2M(4)} | read-write | mandatory |
| lanIpMulticast OBJECT-TYPE The Prestige supports both IGMP version 1 (IGMP-v1) and version 2 (IGMP-v2). At start up, the Prestige queries all directly connected networks to gather group membership. After that, the Prestige periodically updates this information. Select None to disable IP Multicasting. | 1.3.6.1.4.1.890.1.2.1.3.3.5 | INTEGER {none(1), igmpv1(2), igmpv2(3)} | read-write | mandatory |
| lanWireless OBJECT-IDENTITY | 1.3.6.1.4.1.890.1.2.1.3.4 | |||
| wlanTable OBJECT-TYPE A list of ip static route entries. | 1.3.6.1.4.1.890.1.2.1.3.4.1 | not-accessible | mandatory | |
| wlanEntry OBJECT-TYPE An wireless lan entry containing comment object for a particular ESS. | 1.3.6.1.4.1.890.1.2.1.3.4.1.1 | not-accessible | mandatory | |
| wlanEssStatus OBJECT-TYPE This object allows you to activate/deactivate this ESS. | 1.3.6.1.4.1.890.1.2.1.3.4.1.1.1 | INTEGER {other(1), active(2), inactive(3)} | read-write | mandatory |
| wlanCardID OBJECT-TYPE The Card ID indicates the wireless lan card number. | 1.3.6.1.4.1.890.1.2.1.3.4.1.1.2 | INTEGER | read-write | mandatory |
| wlanESSID OBJECT-TYPE The ESSID(Extended Service Set Identification) is a unique name to identify the Prestige in the wireless LAN. Wireless clients associating to the Prestige must have the same ESSID. | 1.3.6.1.4.1.890.1.2.1.3.4.1.1.3 | DisplayString (SIZE(0..31)) | read-write | mandatory |
| wlanHideESSID OBJECT-TYPE Select Yes to hide the ESSID in so a station can not obtain the ESSID through passive scanning. Select No to make the ESSID visible so a station can obtain the ESSID through passive scanning. | 1.3.6.1.4.1.890.1.2.1.3.4.1.1.4 | INTEGER {other(1), yes(2), no(3)} | read-write | mandatory |
| wlanChannelID OBJECT-TYPE The range of radio frequencies used by IEEE 802.11b wireless devices is called a channel. | 1.3.6.1.4.1.890.1.2.1.3.4.1.1.5 | INTEGER | read-write | mandatory |
| wlanRTSThreshold OBJECT-TYPE Select this option to enable RTS/CTS handshake. Data with its rame size larger than this value will perform the RTS/CTS handshake. Setting this attribute to be larger than the maximum MSDU (MAC service data unit) size turns off the RTS/CTS handshake. Setting this attribute to zero turns on the RTS/CTS handshake. | 1.3.6.1.4.1.890.1.2.1.3.4.1.1.6 | INTEGER | read-write | mandatory |
| wlanFragThreshold OBJECT-TYPE The threshold (number of bytes) for the fragmentation boundary for directed messages. It is the maximum data fragment size that can be sent. | 1.3.6.1.4.1.890.1.2.1.3.4.1.1.7 | INTEGER | read-write | mandatory |
| wlanWEPStatus OBJECT-TYPE WEP (Wired Equivalent Privacy) encrypts data frames before transmitting over the wireless network. Select Disable allows all wireless computers to communicate with the access points without any data encryption. Select 64-bit WEP or 128-bit WEP to allow data encryption. | 1.3.6.1.4.1.890.1.2.1.3.4.1.1.8 | INTEGER {other(1), disable(2), WEP-64-bit(3), WEP-128-bit(4)} | read-write | mandatory |
| wlanDefaultKey OBJECT-TYPE The default transmit WEP key. | 1.3.6.1.4.1.890.1.2.1.3.4.1.1.9 | INTEGER | read-write | mandatory |
| wlanWepKey1 OBJECT-TYPE The WEP key #1 value for WEP encryption. If you chose WepKey-64-bit, then enter any 10 hexadecimal digits ('0-9', 'A-F') or 5 ASCII characters. If you chose WepKey-128-bit, then enter 26 hexadecimal digits ('0-9', 'AF') or 10 ASCII characters. | 1.3.6.1.4.1.890.1.2.1.3.4.1.1.10 | DisplayString (SIZE(0..26)) | read-write | mandatory |
| wlanWepKey2 OBJECT-TYPE The WEP key #2 value for WEP encryption. If you chose WepKey-64-bit, then enter any 10 hexadecimal digits ('0-9', 'A-F') or 5 ASCII characters. If you chose WepKey-128-bit, then enter 26 hexadecimal digits ('0-9', 'AF') or 10 ASCII characters. | 1.3.6.1.4.1.890.1.2.1.3.4.1.1.11 | DisplayString (SIZE(0..26)) | read-write | mandatory |
| wlanWepKey3 OBJECT-TYPE The WEP key #3 value for WEP encryption.If you chose WepKey-64-bit, then enter any 10 hexadecimal digits ('0-9', 'A-F') or 5 ASCII characters. If you chose WepKey-128-bit, then enter 26 hexadecimal digits ('0-9', 'AF') or 10 ASCII characters. | 1.3.6.1.4.1.890.1.2.1.3.4.1.1.12 | DisplayString (SIZE(0..26)) | read-write | mandatory |
| wlanWepKey4 OBJECT-TYPE The WEP key #4 value for WEP encryption. If you chose WepKey-64-bit, then enter any 10 hexadecimal digits ('0-9', 'A-F') or 5 ASCII characters. If you chose WepKey-128-bit, then enter 26 hexadecimal digits ('0-9', 'AF') or 10 ASCII characters. | 1.3.6.1.4.1.890.1.2.1.3.4.1.1.13 | DisplayString (SIZE(0..26)) | read-write | mandatory |
| prestigeStaticRoute OBJECT-IDENTITY | 1.3.6.1.4.1.890.1.2.1.4 | |||
| ipStaticRouteTable OBJECT-TYPE A list of ip static route entries. | 1.3.6.1.4.1.890.1.2.1.4.1 | not-accessible | mandatory | |
| ipStaticRouteEntry OBJECT-TYPE An ip static route entry containing comment object for a particular ip static route. | 1.3.6.1.4.1.890.1.2.1.4.1.1 | not-accessible | mandatory | |
| ipStaticRouteIndex OBJECT-TYPE The index of ip static route entry. | 1.3.6.1.4.1.890.1.2.1.4.1.1.1 | INTEGER | read-only | mandatory |
| ipStaticRouteName OBJECT-TYPE The descriptive name for this route. This is for identification purpose only. | 1.3.6.1.4.1.890.1.2.1.4.1.1.2 | DisplayString (SIZE(0..10)) | read-write | mandatory |
| ipStaticRouteActiveStatus OBJECT-TYPE This object allows you to activate/deactivate this static route. | 1.3.6.1.4.1.890.1.2.1.4.1.1.3 | INTEGER {other(1), yes(2), no(3)} | read-write | mandatory |
| ipStaticRouteDestIpAddr OBJECT-TYPE This object specifies the IP network address of the final destination. Routing is always based on network number. If you need to specify a route to a single host, use a subnet mask of 255.255.255.255 in the ipStaticRouteSubnetMask object to force the network number to be identical to the host ID. | 1.3.6.1.4.1.890.1.2.1.4.1.1.4 | IpAddress | read-write | mandatory |
| ipStaticRouteSubnetMask OBJECT-TYPE The subnet mask specifies the network number portion of the ipStaticRouteDestIpAddr. | 1.3.6.1.4.1.890.1.2.1.4.1.1.5 | IpAddress | read-write | mandatory |
| ipStaticRouteGatewayIpAddr OBJECT-TYPE The gateway is an immediate neighbor of your Prestige that will forward the packet to the destination. On the LAN, the gateway must be a router on the same segment as your Prestige; over WAN, the gateway must be the IP address of one of the remote nodes. | 1.3.6.1.4.1.890.1.2.1.4.1.1.6 | IpAddress | read-write | mandatory |
| ipStaticRouteMetric OBJECT-TYPE Metric represents the 'cost' of transmission for routing purposes. IP routing uses hop count as the measurement of cost, with a minimum of 1 for directly connected networks. Enter a number that approximates the cost for this link. The number need not be precise, but it must be between 1 and 15. In practice, 2 or 3 is usually a good number. | 1.3.6.1.4.1.890.1.2.1.4.1.1.7 | INTEGER | read-only | mandatory |
| ipStaticRoutePirvate OBJECT-TYPE This parameter determines if the Prestige will include the route to this remote node in its RIP broadcasts. If set to Yes, this route is kept private and is not included in RIP broadcast. If No, the route to this remote node will be propagated to other hosts through RIP broadcasts. | 1.3.6.1.4.1.890.1.2.1.4.1.1.8 | INTEGER {other(1), yes(2), no(3)} | read-only | mandatory |
| bridgeStaticRouteTable OBJECT-TYPE A list of bridge static route entries. | 1.3.6.1.4.1.890.1.2.1.4.2 | not-accessible | mandatory | |
| bridgeStaticRouteEntry OBJECT-TYPE An bridge static route entry containing comment object for a particular bridge static route. | 1.3.6.1.4.1.890.1.2.1.4.2.1 | not-accessible | mandatory | |
| bridgeStaticRouteIndex OBJECT-TYPE The index of bridge static route entry. | 1.3.6.1.4.1.890.1.2.1.4.2.1.1 | INTEGER | read-only | mandatory |
| bridgeStaticRouteName OBJECT-TYPE The descriptive name for this route. This is for identification purpose only. | 1.3.6.1.4.1.890.1.2.1.4.2.1.2 | DisplayString (SIZE(0..10)) | read-write | mandatory |
| bridgeStaticRouteActiveStatus OBJECT-TYPE This object allows you to activate/deactivate this static route. | 1.3.6.1.4.1.890.1.2.1.4.2.1.3 | INTEGER {other(1), yes(2), no(3)} | read-write | mandatory |
| bridgeStaticRouteEtherAddr OBJECT-TYPE This object specifies the the MAC address of the destination machine that you wish to bridge the packets to. | 1.3.6.1.4.1.890.1.2.1.4.2.1.4 | PhysAddress | read-write | mandatory |
| bridgeStaticRouteIpAddr OBJECT-TYPE If available, this object specifies the IP address of the destination machine that you wish to bridge the packets to. | 1.3.6.1.4.1.890.1.2.1.4.2.1.5 | IpAddress | read-write | mandatory |
| bridgeStaticRouteGatewayNode OBJECT-TYPE This object specifies the number of the remote node that is the gateway of this static route. | 1.3.6.1.4.1.890.1.2.1.4.2.1.6 | INTEGER | read-write | mandatory |
| prestigeFilterConfig OBJECT-IDENTITY | 1.3.6.1.4.1.890.1.2.1.5 | |||
| filterSetTable OBJECT-TYPE A list of filter set entries. The number of entries is 12 | 1.3.6.1.4.1.890.1.2.1.5.1 | not-accessible | mandatory | |
| filterSetEntry OBJECT-TYPE An filter set entry containing comment object for a particular filter set. | 1.3.6.1.4.1.890.1.2.1.5.1.1 | not-accessible | mandatory | |
| filterSetIndex OBJECT-TYPE The index of filter set. | 1.3.6.1.4.1.890.1.2.1.5.1.1.1 | INTEGER | read-only | mandatory |
| filterSetComment OBJECT-TYPE The descriptive name or comment of filter set | 1.3.6.1.4.1.890.1.2.1.5.1.1.2 | DisplayString (SIZE(0..15)) | read-write | mandatory |
| filterRuleTable OBJECT-TYPE A list of filter rule entries. The number of entries is (number of filter set) * (number of rule set per filter set) | 1.3.6.1.4.1.890.1.2.1.5.2 | not-accessible | mandatory | |
| filterRuleEntry OBJECT-TYPE An filter rule entry containing TCP/IP and/or generic filter rules for a particular filter set. | 1.3.6.1.4.1.890.1.2.1.5.2.1 | not-accessible | mandatory | |
| filterRuleIndex OBJECT-TYPE The index of rule set. | 1.3.6.1.4.1.890.1.2.1.5.2.1.1 | INTEGER | read-only | mandatory |
| filterRuleActiveStatus OBJECT-TYPE This object activates/deactivates the filter rule. | 1.3.6.1.4.1.890.1.2.1.5.2.1.2 | INTEGER {other(1), yes(2), no(3)} | read-write | mandatory |
| filterRuleType OBJECT-TYPE There are two types of filter rules: TCP/IP and Generic. TCP/IP rules allow you to base the rule on the fields in the IP and the upper layer protocol, e.g., UDP and TCP, headers. The purpose of generic rules is to allow you to filter non-IP packets. For IP, it is generally easier to use the IP rules directly. For generic rules, the Prestige treats a packet as a byte stream as opposed to an IP packet. You specify the portion of the packet to check with the Offset (from 0) and the Length fields, both in bytes. The Prestige applies the Mask (bit-wise ANDing) to the data portion before comparing the result against the Value to determine a match. The Mask and Value are specified in hexadecimal numbers. Note that it takes two hexadecimal digits to represent a byte, so if the length is 4, the value in either field will take 8 digits, e.g., FFFFFFFF. | 1.3.6.1.4.1.890.1.2.1.5.2.1.3 | INTEGER {other(1), tcpIp(2), generic(3)} | read-write | mandatory |
| filterRuleIpProtocol OBJECT-TYPE For TCP/IP filter, protocol refers to the upper layer protocol, e.g., TCP is 6, UDP is 17 and ICMP is 1. For generic filter this object is disregarded. | 1.3.6.1.4.1.890.1.2.1.5.2.1.4 | INTEGER (0..255) | read-write | mandatory |
| filterRuleIpSourceRoute OBJECT-TYPE For TCP/IP filter, If Yes, the rule applies to packet with IP source route option; else the packet must not have source route option. The majority of IP packets do not have source route. For generic filter this object is disregarded. | 1.3.6.1.4.1.890.1.2.1.5.2.1.5 | INTEGER {other(1), yes(2), no(3)} | read-write | mandatory |
| filterRuleDestIpAddr OBJECT-TYPE For TCP/IP filter, it's the destination IP Address of the packet you wish to filter. This object is disregarded if it is 0.0.0.0. For generic filter this object is disregarded. | 1.3.6.1.4.1.890.1.2.1.5.2.1.6 | IpAddress | read-write | mandatory |
| filterRuleDestIpMask OBJECT-TYPE For TCP/IP filter, it's the IP mask apply to the Destination IP Addr. For generic filter this object is disregarded. | 1.3.6.1.4.1.890.1.2.1.5.2.1.7 | IpAddress | read-write | mandatory |
| filterRuleDestPort OBJECT-TYPE For TCP/IP filter, it's the destination port of the packets that you wish to filter. For generic filter this object is disregarded. | 1.3.6.1.4.1.890.1.2.1.5.2.1.8 | INTEGER (0..65535) | read-write | mandatory |
| filterRuleDestPortComp OBJECT-TYPE For TCP/IP filter, this object select the comparison to apply to the filterRuleDestPortComp in the packet against the value given in filterRuleDestPortComp. For generic filter this object is disregarded. | 1.3.6.1.4.1.890.1.2.1.5.2.1.9 | INTEGER {none(1), equal(2), notequal(3), less(4), greater(5)} | read-write | mandatory |
| filterRuleSourceIpAddr OBJECT-TYPE For TCP/IP filter, it's the source IP Address of the packet you wish to filter. This object is disregarded if it is 0.0.0.0. For generic filter this object is disregarded. | 1.3.6.1.4.1.890.1.2.1.5.2.1.10 | IpAddress | read-write | mandatory |
| filterRuleSourceIpMask OBJECT-TYPE For TCP/IP filter, it's the IP mask apply to the source IP Addr. For generic filter this object is disregarded. | 1.3.6.1.4.1.890.1.2.1.5.2.1.11 | IpAddress | read-write | mandatory |
| filterRuleSourcePort OBJECT-TYPE For TCP/IP filter, it's the source port of the packets that you wish to filter. For generic filter this object is disregarded. | 1.3.6.1.4.1.890.1.2.1.5.2.1.12 | INTEGER (0..65535) | read-write | mandatory |
| filterRuleSourcePortComp OBJECT-TYPE For TCP/IP filter, this object select the comparison to apply to the filterRuleSourcePort in the packet against the value given in filterRuleSourcePort. For generic filter this object is disregarded. | 1.3.6.1.4.1.890.1.2.1.5.2.1.13 | INTEGER {none(1), equal(2), notequal(3), less(4), greater(5)} | read-write | mandatory |
| filterRuleTcpEstab OBJECT-TYPE For TCP/IP filter, this object is applicable only when filterRuleIpProtocol is 6, TCP. If yes, the rule matches only established TCP connections; else the rule matches all TCP packets. For generic filter this object is disregarded. | 1.3.6.1.4.1.890.1.2.1.5.2.1.14 | INTEGER {other(1), yes(2), no(3)} | read-write | mandatory |
| filterRuleGenericOffset OBJECT-TYPE For generic filter, this object is the starting byte of the data portion in the packet that you wish to compare. For TCP/IP filter this object is disregarded. | 1.3.6.1.4.1.890.1.2.1.5.2.1.15 | INTEGER (0..255) | read-write | mandatory |
| filterRuleGenericLength OBJECT-TYPE For generic filter, this object is byte count of the data portion in the packet that you wish to compare. For TCP/IP filter this object is disregarded. | 1.3.6.1.4.1.890.1.2.1.5.2.1.16 | INTEGER (0..8) | read-write | mandatory |
| filterRuleGenericMask OBJECT-TYPE For generic filter, this object is the Mask apply to the data portion before comparison. For TCP/IP filter this object is disregarded. | 1.3.6.1.4.1.890.1.2.1.5.2.1.17 | OCTET STRING (SIZE(6)) | read-write | mandatory |
| filterRuleGenericValue OBJECT-TYPE For generic filter, this object is the value to compare with the data portion. For TCP/IP filter this object is disregarded. | 1.3.6.1.4.1.890.1.2.1.5.2.1.18 | OCTET STRING (SIZE(6)) | read-write | mandatory |
| filterRuleMore OBJECT-TYPE If yes, a matching packet is passed to the next filter rule before an action is taken; if no, the packet is disposed of according to the action fields. | 1.3.6.1.4.1.890.1.2.1.5.2.1.19 | INTEGER {other(1), yes(2), no(3)} | read-write | mandatory |
| filterRuleLog OBJECT-TYPE * None : No packets will be logged. * Action Matched : Only packets that match the rule parameters will be logged. * Action Not Matched : Only packets that do not match the rule parameters will be logged. * Both : All packets will be logged. | 1.3.6.1.4.1.890.1.2.1.5.2.1.20 | INTEGER {none(1), actMatched(2), atcNotMatch(3), both(4)} | read-write | mandatory |
| filterRuleActMatched OBJECT-TYPE This object select the action for a matching packet. If filterRuleMore is Yes, this object is disregarded. | 1.3.6.1.4.1.890.1.2.1.5.2.1.21 | INTEGER {other(1), checkNextRule(2), forward(3), drop(4)} | read-write | mandatory |
| filterRuleActNotMatched OBJECT-TYPE This object select the action for a packet not matching the rule. If filterRuleMore is Yes, this object is disregarded. | 1.3.6.1.4.1.890.1.2.1.5.2.1.22 | INTEGER {other(1), checkNextRule(2), forward(3), drop(4)} | read-write | mandatory |
| prestigeXDSL OBJECT-IDENTITY | 1.3.6.1.4.1.890.1.2.1.6 | |||
| prestigeTraps OBJECT-IDENTITY | 1.3.6.1.4.1.890.1.2.1.99 | |||
| whyReboot OBJECT-TYPE Send a message to the manager that the system is going to reboot. The variable is the reason of rebooting. | 1.3.6.1.4.1.890.1.2.1.99.1 | DisplayString | read-only | mandatory |
Notifications
| Name | OID | Status |
|---|---|---|
| reboot NOTIFICATION-TYPE Send a message to the manager that the system is going to reboot. The variable is the reason why the system reboots. | 1.3.6.1.4.1.890.1.2.1.0.1 |