SL-SONET-MIB
- Registered at
- 1.3.6.1.4.1.4515.1.6
- Last updated
- 2000-08-28 00:00
- Organization
- PacketLight Networks Ltd.
- Namespace
- packetlight
- Source file
SL-SONET-MIB- Digest
sha256:50f9a1b9f6fea112bbfdc06889e19504a7ebf7e1dfc4697ecfc6e76fb75e84fa
Description
This MIB module describes the SiteLight SONET Service. The mib contains the extensions required for the rfc2558.
Contact
Omri_Viner@PacketLight.com
Imports
| From | Symbols |
|---|---|
| IF-MIB | InterfaceIndex, ifIndex |
| PerfHist-TC-MIB | PerfCurrentCount, PerfIntervalCount, PerfTotalCount |
| SL-NE-MIB | sitelight |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP |
| SNMPv2-SMI | Counter64, Gauge32, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, iso |
| SNMPv2-TC | DisplayString, RowStatus, TEXTUAL-CONVENTION, TruthValue |
Imported by
1 module(s) in this corpus import this one.
Load order
Every file a consumer needs in order to load this module, dependencies first.
IANAifType-MIB IF-MIB PerfHist-TC-MIB SL-NE-MIB SL-SONET-MIB SNMPv2-CONF SNMPv2-MIB SNMPv2-SMI SNMPv2-TC
Under this module's arcs
Where the registration tree carries on below this module.
| Arc | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.4515.1.6.3 | sonetSupPmMIB | SL-SONET-SUP-PM-MIB |
Textual conventions
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| SignalLabel TEXTUAL-CONVENTION STS path signal label -- one byte, C2, class A, is allocated to indicate the construction of the STS SPE. The following hex values of the C2 byte has been defined. | current |
Objects
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| slSonetConfig OBJECT-IDENTITY | 1.3.6.1.4.1.4515.1.6.1 | |||
| slSonetConfigTable OBJECT-TYPE The SONET/SDH configuration table. This table has objects for configuring sonet lines. | 1.3.6.1.4.1.4515.1.6.1.1 | not-accessible | current | |
| slSonetConfigEntry OBJECT-TYPE An entry in the table. There is an entry for each SONET line in the table. Entries are automatically created for an ifType value of sonet(39). 'ifAdminStatus' from the ifTable must be used to enable or disable a line. By default, the line state is down. | 1.3.6.1.4.1.4515.1.6.1.1.1 | not-accessible | current | |
| slSonetConfigFrameScramble OBJECT-TYPE This object is used to disable or enable the Scrambling option in SONET line. Please refer to GR-253-CORE for frame scrambling. | 1.3.6.1.4.1.4515.1.6.1.1.1.1 | INTEGER {disabled(1), enabled(2)} | read-write | current |
| slSonetConfigType OBJECT-TYPE This object represents the configured line type for Trunks: sonetSts48c(5) - 1 x Sts48 (2.5GbTrunk) sonetSts192c(12) - 1 x Sts192 (10Gb Trunk) sonetStsOther(13) - for OC-n interfaces see slSonetFsTable. | 1.3.6.1.4.1.4515.1.6.1.1.1.2 | INTEGER {sonetSts3(1), sonetSts3c(2), sonetSts12(3), sonetSts12c(4), sonetSts48c(5), sonetSts3cx4(6), sonetSts48(7), sonetSts3cx16(8), sonetSts3x16(9), sonetSts12cx4(10), sonetSts12x4(11), sonetSts192c(12), sonetStsOther(13)} | read-write | current |
| slSonetConfigDccSelection OBJECT-TYPE This object selects the DCC type. | 1.3.6.1.4.1.4515.1.6.1.1.1.3 | INTEGER {sonetLineDcc(1), sonetSectionDcc(2), sonetInband(3)} | read-write | current |
| slSonetResetAllCounters OBJECT-TYPE Setting this variable to 1 will cause all of the counters (performance regsters) on this SONET interface to be initialized to zero (0). | 1.3.6.1.4.1.4515.1.6.1.1.1.4 | INTEGER {resetCounters(1)} | read-write | current |
| slSonetPortThresholdTrapEnable OBJECT-TYPE This variable indicates whether threshold traps should be generated for this SONET interface. | 1.3.6.1.4.1.4515.1.6.1.1.1.5 | INTEGER {enabled(1), disabled(2)} | read-write | current |
| slSonetConfigSdThreshold OBJECT-TYPE This object contains the Bit Error Rate threshold for Signal Degrade detection on the working line. Once this threshold is exceeded, an APS switch will occur. This value is 10 to -n where n is between 5 and 9 (read-write). | 1.3.6.1.4.1.4515.1.6.1.1.1.6 | INTEGER (5..9) | read-write | current |
| slSonetConfigSfThreshold OBJECT-TYPE This object contains the Bit Error Rate threshold for Signal Fault detection on the working line. Once this threshold is exceeded, an APS switch will occur. This value is 10 to the -n, where n is between 3 and 5. (read-write) | 1.3.6.1.4.1.4515.1.6.1.1.1.7 | INTEGER (3..5) | read-write | current |
| slSonetCompression OBJECT-TYPE This object applies only for trunk ports. It specifies if the packets should be compressed. 0 - Means no POS compression, 1 - Means POS compression with CRC-32. 2 - Means POS compression with CRC-16. Note that the two connected trunks should be configured to the same value. Note also that the BW calculation of the OC-n should be changed according to this value. | 1.3.6.1.4.1.4515.1.6.1.1.1.9 | INTEGER {uncompress(0), posCompress32(1), posCompress16(2)} | read-write | current |
| slSonetOverheadTunneling OBJECT-TYPE The section and line overhead tunneling configuration: none(0) - no tunneling support lineDcc(1) - line DCC tunneling k1k2(2) - line DCC + protection k byte full(3) - all transport overhead bytes are tunneled | 1.3.6.1.4.1.4515.1.6.1.1.1.10 | INTEGER {none(0), lineDcc(1), k1k2(2), full(3)} | read-write | current |
| slSonetLopBitmask OBJECT-TYPE The LOP status. Each bit of the bits represent the status of the LOP alarm in corresponding STS. For a path with more than a single STS, only the value of the first STS in the path is relevant. This object is relevant only for the OC-N cards and not for the Trunk. In the next future this object will be replaced with an object of a new table that shall describe the OC-N frame structure. | 1.3.6.1.4.1.4515.1.6.1.1.1.11 | Counter64 | read-only | current |
| slSonetTdmTrunk OBJECT-TYPE This object is applicable only to the OC-n ports. TRUE - means that the OC-n port is used as a TDM Trunk. FLASE - means normal OC-n port. | 1.3.6.1.4.1.4515.1.6.1.1.1.12 | TruthValue | read-write | current |
| slSonetFsApply OBJECT-TYPE Writing to this object activate the slSonetFsTable setting. This allow the NMS to do many changes to the slSonetFsTable and then APPLY them at once. This prevent from going through unconsistent steps. This object always returns the value 0. | 1.3.6.1.4.1.4515.1.6.1.1.1.13 | INTEGER | read-write | current |
| slSonetTxLte OBJECT-TYPE The SS bits to transmit (bits 5,6 in H1,H1*). | 1.3.6.1.4.1.4515.1.6.1.1.1.14 | INTEGER {ssb00(1), ssb10(2), auto(5)} | read-write | current |
| slSonetReceivedLte OBJECT-TYPE The detected LTE type, according to the received SS bits (bits 5,6 in H1,H1*). | 1.3.6.1.4.1.4515.1.6.1.1.1.15 | INTEGER {ssb00(1), ssb10(2), ssb01(3), ssb11(4), ssbinv(5)} | read-only | current |
| slSonetResetPmThreshold OBJECT-TYPE Setting this variable to 1 will reset the PM threshold parameters to the factory defaults. | 1.3.6.1.4.1.4515.1.6.1.1.1.16 | INTEGER {resetCounters(1)} | read-write | current |
| slSonetResetAlsParams OBJECT-TYPE Setting this variable to 1 will reset the ALS parameters to the factory defaults. | 1.3.6.1.4.1.4515.1.6.1.1.1.17 | INTEGER {resetCounters(1)} | read-write | current |
| slSonetTransceiverType OBJECT-TYPE The tranceiver type. | 1.3.6.1.4.1.4515.1.6.1.1.1.18 | INTEGER {none(1), shortWave(2), longWave(3)} | read-only | current |
| slSonetTransceiverMedia OBJECT-TYPE The tranceiver media. | 1.3.6.1.4.1.4515.1.6.1.1.1.19 | INTEGER {none(1), sm(2), mm(3)} | read-only | current |
| slSonetOh OBJECT-IDENTITY | 1.3.6.1.4.1.4515.1.6.2 | |||
| slSonetOhTrace OBJECT-IDENTITY | 1.3.6.1.4.1.4515.1.6.2.1 | |||
| slSonetTraceTable OBJECT-TYPE The SONET/SDH Trace table. This table contains objects for tracing the sonet section and path. | 1.3.6.1.4.1.4515.1.6.2.1.1 | not-accessible | current | |
| slSonetTraceEntry OBJECT-TYPE An entry in the trace table. Entries exist for active sonet interfaces. The objects in this table are used to verify continued connection between the two ends of the line. | 1.3.6.1.4.1.4515.1.6.2.1.1.1 | not-accessible | current | |
| slSonetTraceMode OBJECT-TYPE Determine the Trace Message Mode. | 1.3.6.1.4.1.4515.1.6.2.1.1.1.1 | INTEGER {enable(1), disable(2), monitoring(3)} | read-write | current |
| slSonetTraceToTransmit OBJECT-TYPE Sonet Trace To Transmit. This is string that is transmitted to perform Sonet trace diagnostics. The trace string is repetitively transmited so that a trace receiving terminal can verify its continued connection to the intended transmitter. The default value is a zero-length string. Unless this object is set to a non-zero length string, tracing will not be performed. The Agent is responsible to pad the end of the string with <CR><LF>. | 1.3.6.1.4.1.4515.1.6.2.1.1.1.2 | DisplayString (SIZE(0..62)) | read-write | current |
| slSonetTraceToExpect OBJECT-TYPE Sonet Trace Massage To Expect. The receiving terminal verifies if the incoming string matches this string. The value of 'slSonetTraceFailure' indicates whether a trace mismatch occurred. The default value is a zero-length string. The Agent is responsible to pad the end of the string with <CR><LF>. | 1.3.6.1.4.1.4515.1.6.2.1.1.1.3 | DisplayString (SIZE(0..62)) | read-write | current |
| slSonetTraceFailure OBJECT-TYPE The value of this object is set to 'true' when Sonet Section received trace does not match the 'slSonetTraceToExpect'. | 1.3.6.1.4.1.4515.1.6.2.1.1.1.4 | TruthValue | read-only | current |
| slSonetTraceReceived OBJECT-TYPE This object is used to view the Sonet Trace Message that is received by the receiving terminal. The Agent is responsible to pad the end of the string with <CR><LF>. | 1.3.6.1.4.1.4515.1.6.2.1.1.1.5 | DisplayString (SIZE(0..62)) | read-only | current |
| slSonetOhSl OBJECT-IDENTITY | 1.3.6.1.4.1.4515.1.6.2.2 | |||
| slSonetSlTable OBJECT-TYPE The SONET/SDH Signal Label table. This table contains signal label for the sonet path. | 1.3.6.1.4.1.4515.1.6.2.2.1 | not-accessible | current | |
| slSonetSlEntry OBJECT-TYPE An entry in the SONET/SDH Signal Label table. The entries exist for active sonet lines. The objects in this table are used to verify continued connection between the two ends of the line. | 1.3.6.1.4.1.4515.1.6.2.2.1.1 | not-accessible | current | |
| slSonetSlToTransmit OBJECT-TYPE Sonet Signal Label To Transmit. | 1.3.6.1.4.1.4515.1.6.2.2.1.1.2 | SignalLabel | read-write | current |
| slSonetSlToExpect OBJECT-TYPE Sonet Signal Label To Expect. | 1.3.6.1.4.1.4515.1.6.2.2.1.1.3 | SignalLabel | read-write | current |
| slSonetSlFailure OBJECT-TYPE The value of this object is set to 'true' when Sonet received signal label does not match the 'slSonetSlToExpect'. | 1.3.6.1.4.1.4515.1.6.2.2.1.1.4 | TruthValue | read-only | current |
| slSonetSlReceived OBJECT-TYPE This object is used to view the Sonet Signal Label that is received by the receiving terminal. | 1.3.6.1.4.1.4515.1.6.2.2.1.1.5 | INTEGER (0..255) | read-only | current |
| slSonetOhTraps OBJECT-IDENTITY | 1.3.6.1.4.1.4515.1.6.2.3 | |||
| slSonetPos OBJECT-IDENTITY | 1.3.6.1.4.1.4515.1.6.6 | |||
| slSonetPosTable OBJECT-TYPE The POS PM Table. | 1.3.6.1.4.1.4515.1.6.6.1 | not-accessible | current | |
| slSonetPosEntry OBJECT-TYPE The entries exist for active Trunk sonet lines ifType = pos(171). The objects in this table are used to moitor the POS layer. | 1.3.6.1.4.1.4515.1.6.6.1.1 | not-accessible | current | |
| slSonetPosFcs OBJECT-TYPE The Number of FCS Errors. | 1.3.6.1.4.1.4515.1.6.6.1.1.1 | Gauge32 | read-only | current |
| slSonetPosAbort OBJECT-TYPE The Number of Aborted packets. | 1.3.6.1.4.1.4515.1.6.6.1.1.2 | Gauge32 | read-only | current |
| slSonetPosMinViolation OBJECT-TYPE The Number of Minimum length violation packets. | 1.3.6.1.4.1.4515.1.6.6.1.1.3 | Gauge32 | read-only | current |
| slSonetPosMaxViolation OBJECT-TYPE The Number of Maximum length violation packets. | 1.3.6.1.4.1.4515.1.6.6.1.1.4 | Gauge32 | read-only | current |
| slSonetPosRxfifoDiscard OBJECT-TYPE The Number of packets discarded due to RXFIFO error. | 1.3.6.1.4.1.4515.1.6.6.1.1.5 | Gauge32 | read-only | current |
| slSonetPosPacketReceived OBJECT-TYPE The Number of packets received. | 1.3.6.1.4.1.4515.1.6.6.1.1.6 | Counter64 | read-only | current |
| slSonetPosPacketReceivedOk OBJECT-TYPE The Number of error free packets. | 1.3.6.1.4.1.4515.1.6.6.1.1.7 | Counter64 | read-only | current |
| slSonetAls OBJECT-IDENTITY | 1.3.6.1.4.1.4515.1.6.7 | |||
| slSonetAlsTable OBJECT-TYPE The ALS configuration Table. | 1.3.6.1.4.1.4515.1.6.7.1 | not-accessible | current | |
| slSonetAlsEntry OBJECT-TYPE The entries exist for active sonet lines ifType = sonet(39). The objects in this table are used to configure the ALS algorithm. | 1.3.6.1.4.1.4515.1.6.7.1.1 | not-accessible | current | |
| slSonetAlsMode OBJECT-TYPE Enable/Disable the ALS algorithm. Note that the if the Laser Admin Status is 'down' the ALS mechanism is not operational. | 1.3.6.1.4.1.4515.1.6.7.1.1.1 | INTEGER {enable(1), disable(2)} | read-write | current |
| slSonetLosDeclareTime OBJECT-TYPE Time to declare optical LOS present or clear: 550 +- 50 msec. | 1.3.6.1.4.1.4515.1.6.7.1.1.2 | INTEGER {ms500(1), ms550(2), ms600(3)} | read-write | current |
| slSonetTestPulseTime OBJECT-TYPE Manual restart for test Pulse time (in manual restart) - 90+-10 sec. | 1.3.6.1.4.1.4515.1.6.7.1.1.3 | INTEGER {s80(1), s90(2), s100(3)} | read-write | current |
| slSonetManualPulseTime OBJECT-TYPE Manual restart Pulse time (in manual mode) - 2+-0.25 sec. | 1.3.6.1.4.1.4515.1.6.7.1.1.4 | INTEGER {ms1750(1), ms2000(2), ms2250(3)} | read-write | current |
| slSonetAutomaticPulseTime OBJECT-TYPE Automatic restart Pulse time (in automatic mode) - 2+-0.25 sec. | 1.3.6.1.4.1.4515.1.6.7.1.1.5 | INTEGER {ms1750(1), ms2000(2), ms2250(3)} | read-write | current |
| slSonetAutomaticDelayTime OBJECT-TYPE In Automatic mode. The delay between two laser re-activations. | 1.3.6.1.4.1.4515.1.6.7.1.1.6 | INTEGER (60..300) | read-write | current |
| slSonetLaserTestActivate OBJECT-TYPE Activate the laser for test operation. | 1.3.6.1.4.1.4515.1.6.7.1.1.7 | INTEGER {activate(1)} | read-write | current |
| slSonetLaserManualActivate OBJECT-TYPE Activate the laser manual operation. | 1.3.6.1.4.1.4515.1.6.7.1.1.8 | INTEGER {activate(1)} | read-write | current |
| slSonetFs OBJECT-IDENTITY | 1.3.6.1.4.1.4515.1.6.8 | |||
| slSonetFsTable OBJECT-TYPE The frame structure configuration Table. In order to define a new path the NMS should create and configure an entry in this table. The table is also used to monitor the status of the LOP alarm per path. | 1.3.6.1.4.1.4515.1.6.8.1 | not-accessible | current | |
| slSonetFsEntry OBJECT-TYPE The entries exist for sonet paths ifType = sonet(39). The objects in this table are used to configure the frame structure. Each OC-N line interface shall maintain a static table with number of lines equal to the N. Initially the table will be initialized to STS-Nc. | 1.3.6.1.4.1.4515.1.6.8.1.1 | not-accessible | current | |
| slSonetFsIfIndex OBJECT-TYPE The interface index. | 1.3.6.1.4.1.4515.1.6.8.1.1.1 | InterfaceIndex | read-only | current |
| slSonetFsSts OBJECT-TYPE The number of the first STS in the path. Note that no all values are legal because there is no support for combus with mixed structure | 1.3.6.1.4.1.4515.1.6.8.1.1.2 | INTEGER | read-only | current |
| slSonetFsWidth OBJECT-TYPE The number STS's in the path. The width is only valid for the first STS in the path. The other STSs of the path will have width=0. | 1.3.6.1.4.1.4515.1.6.8.1.1.3 | INTEGER | read-write | current |
| slSonetFsFullPathTermination OBJECT-TYPE FALSE - means partial path termination (only LOP alarm). TRUE - include full support for path Alarms and PM counters. | 1.3.6.1.4.1.4515.1.6.8.1.1.4 | TruthValue | read-write | current |
| slSonetFsGranularity OBJECT-TYPE This value is set by the NMS according to the configured frame structure. Each VC-3 that is mapped to AUG-1 via VC-4 should have the value vc4(1). Otherwise the value should be vc3(2). | 1.3.6.1.4.1.4515.1.6.8.1.1.5 | INTEGER {vc4(1), vc3(2)} | read-write | current |
| slSonetTraps OBJECT-IDENTITY | 1.3.6.1.4.1.4515.1.6.11 |
Notifications
| Name | OID | Status |
|---|---|---|
| slSonetFsTableChange NOTIFICATION-TYPE A slSonetFsTableChange trap is sent when the content of the slSonetFsTable is changed. This trap may be used by the NMS to identify the removal of path interfaces, or addition of new path interfaces | 1.3.6.1.4.1.4515.1.6.11.1 | current |