MIBs Depot

JNX-OPT-IF-MIB

Registered at
1.3.6.1.4.1.2636.3.73.1
Last updated
2003-08-13 00:00
Organization
IETF AToM MIB Working Group
Revisions
2003-08-13 00:00
Namespace
juniper
Source file
JNX-OPT-IF-MIB
Digest
sha256:15ae460ce68131def1b8f1c6c46b3f164a2965e7b38957d5a2a39d64a03fb5ce

Description

The MIB module to describe pre-OTN and OTN interfaces. Copyright (C) The Internet Society (2003). This version of this MIB module is part of RFC 3591; see the RFC itself for full legal notices.

Contact

WG charter: http://www.ietf.org/html.charters/atommib-charter.html Mailing Lists: General Discussion: atommib@research.telcordia.com To Subscribe: atommib-request@research.telcordia.com RFC 3591 Optical Interface Type MIB September 2003 Editor: Hing-Kam Lam Postal: Lucent Technologies, Room 4C-616 101 Crawfords Corner Road Holmdel, NJ 07733 Tel: +1 732 949 8338 Email: hklam@lucent.com

Imports

FromSymbols
IF-MIBifIndex
JUNIPER-SMIjnxoptIfMibRoot
SNMP-FRAMEWORK-MIBSnmpAdminString
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP
SNMPv2-SMIGauge32, Integer32, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, Unsigned32, iso, transmission
SNMPv2-TCDisplayString, RowPointer, RowStatus, TEXTUAL-CONVENTION, TruthValue

Imported by

1 module(s) in this corpus import this one.

Load order

Every file a consumer needs in order to load this module, dependencies first.

IANAifType-MIB
IF-MIB
JNX-OPT-IF-MIB
JUNIPER-SMI
SNMP-FRAMEWORK-MIB
SNMPv2-CONF
SNMPv2-MIB
SNMPv2-SMI
SNMPv2-TC

Under this module's arcs

Where the registration tree carries on below this module.

ArcNameModule
1.3.6.1.4.1.2636.3.73.1.3jnxoptIfExtMibModuleJNX-OPT-IF-EXT-MIB

Textual conventions

NameOIDSyntaxAccessStatus
JnxoptIfAcTI
TEXTUAL-CONVENTION
The trace identifier (TI) accepted at the receiver.
current
JnxoptIfBitRateK
TEXTUAL-CONVENTION
Indicates the index that is used to represent a supported bit rate and the different versions of OPUk, ODUk and OTUk. Allowed values of k are defined in ITU-T G.709. Currently allowed values in G.709 are: k=1 represents an approximate bit rate of 2.5 Gbit/s, k=2 represents an approximate bit rate of 10 Gbit/s, k=3 represents an approximate bit rate of 40 Gbit/s.
current
JnxoptIfDEGM
TEXTUAL-CONVENTION
Indicates the threshold level for declaring a Degraded Signal defect (dDEG). A dDEG shall be declared if JnxoptIfDEGM consecutive bad PM Seconds are detected.
current
JnxoptIfDEGThr
TEXTUAL-CONVENTION
Indicates the threshold level for declaring a performance monitoring (PM) Second to be bad. A PM Second is declared bad if the percentage of detected errored blocks in that second is greater than or equal to JnxoptIfDEGThr.
current
JnxoptIfDirectionality
TEXTUAL-CONVENTION
Indicates the directionality of an entity.
current
JnxoptIfExDAPI
TEXTUAL-CONVENTION
The Destination Access Point Identifier (DAPI) expected by the receiver.
current
JnxoptIfExSAPI
TEXTUAL-CONVENTION
The Source Access Point Identifier (SAPI) expected by the receiver.
current
JnxoptIfIntervalNumber
TEXTUAL-CONVENTION
Uniquely identifies a 15-minute interval. The interval identified by 1 is the most recently completed interval, and the interval identified by n is the interval immediately preceding the one identified by n-1.
current
JnxoptIfSinkOrSource
TEXTUAL-CONVENTION
Indicates the directionality of an entity that is allowed only to be a source or sink.
current
JnxoptIfTIMDetMode
TEXTUAL-CONVENTION
Indicates the mode of the Trace Identifier Mismatch (TIM) Detection function.
current
JnxoptIfTxTI
TEXTUAL-CONVENTION
The trace identifier (TI) transmitted.
current

Objects

NameOIDSyntaxAccessStatus
jnxoptIfObjects
OBJECT-IDENTITY
1.3.6.1.4.1.2636.3.73.1.1
jnxoptIfOTMn
OBJECT-IDENTITY
1.3.6.1.4.1.2636.3.73.1.1.1
jnxoptIfOTMnTable
OBJECT-TYPE
A table of OTMn structure information.
1.3.6.1.4.1.2636.3.73.1.1.1.1not-accessiblecurrent
jnxoptIfOTMnEntry
OBJECT-TYPE
A conceptual row that contains the OTMn structure information of an optical interface.
1.3.6.1.4.1.2636.3.73.1.1.1.1.1not-accessiblecurrent
jnxoptIfOTMnOrder
OBJECT-TYPE
This object indicates the order of the OTM, which represents the maximum number of wavelengths that can be supported at the bit rate(s) supported on the interface.
1.3.6.1.4.1.2636.3.73.1.1.1.1.1.1Unsigned32 (1..900)read-onlycurrent
jnxoptIfOTMnReduced
OBJECT-TYPE
This object indicates whether a reduced or full functionality is supported at the interface. A value of true means reduced. A value of false means full.
1.3.6.1.4.1.2636.3.73.1.1.1.1.1.2TruthValueread-onlycurrent
jnxoptIfOTMnBitRates
OBJECT-TYPE
This attribute is a bit map representing the bit rate or set of bit rates supported on the interface. The meaning of each bit position is as follows: bitRateK1(0) is set if the 2.5 Gbit/s rate is supported bitRateK2(1) is set if the 10 Gbit/s rate is supported bitRateK3(2) is set if the 40 Gbit/s rate is supported Note that each bit position corresponds to one possible value of the type JnxoptIfBitRateK. The default value of this attribute is system specific.
1.3.6.1.4.1.2636.3.73.1.1.1.1.1.3Bits {bitRateK1(0), bitRateK2(1), bitRateK3(2)}read-onlycurrent
jnxoptIfOTMnInterfaceType
OBJECT-TYPE
This object identifies the type of interface. The value of this attribute will affect the behavior of the OTM with respect to presence/absence of OTM Overhead Signal (OOS) processing and TCM activation. For an IrDI interface, there is no OOS processing and TCM activation is limited to n levels as specified by a TCM level threshold. This object contains two fields that are separated by whitespace. The possible values are: field 1: one of the 4-character ASCII strings 'IrDI' or 'IaDI' field 2: free-form text consisting of printable UTF-8 encoded characters Note that field 2 is optional. If it is not present then there is no requirement for trailing whitespace after field 1. The default values are as follows: field 1: 'IaDI' field 2: an empty string.
1.3.6.1.4.1.2636.3.73.1.1.1.1.1.4SnmpAdminStringread-onlycurrent
jnxoptIfOTMnTcmMax
OBJECT-TYPE
This object identifies the maximum number of TCM levels allowed for any Optical Channel contained in this OTM. A new TCM activation will be rejected if the requested level is greater than the threshold. If InterfaceType object specifies a type of 'IaDI' for this OTM, then this attribute is irrelevant. Possible values: unsigned integers in the range from 0 to 6 inclusive. Default value: 3.
1.3.6.1.4.1.2636.3.73.1.1.1.1.1.5Unsigned32read-writecurrent
jnxoptIfOTMnOpticalReach
OBJECT-TYPE
This object indicates the length the optical signal may travel before requiring termination or regeneration. The meaning of the enumeration are: intraOffice(1) - intra-office (as defined in ITU-T G.957) shortHaul(2) - short haul (as defined in ITU-T G.957) longHaul(3) - long haul (as defined in ITU-T G.957) veryLongHaul(4) - very long haul (as defined in ITU-T G.691) ultraLongHaul(5)- ultra long haul (as defined in ITU-T G.691)
1.3.6.1.4.1.2636.3.73.1.1.1.1.1.6INTEGER {intraOffice(1), shortHaul(2), longHaul(3), veryLongHaul(4), ultraLongHaul(5)}read-onlycurrent
jnxoptIfPerfMon
OBJECT-IDENTITY
1.3.6.1.4.1.2636.3.73.1.1.2
jnxoptIfPerfMonIntervalTable
OBJECT-TYPE
A table of 15-minute performance monitoring interval information.
1.3.6.1.4.1.2636.3.73.1.1.2.1not-accessiblecurrent
jnxoptIfPerfMonIntervalEntry
OBJECT-TYPE
A conceptual row that contains 15-minute performance monitoring interval information of an interface.
1.3.6.1.4.1.2636.3.73.1.1.2.1.1not-accessiblecurrent
jnxoptIfPerfMonCurrentTimeElapsed
OBJECT-TYPE
Number of seconds elapsed in the current 15-minute performance monitoring interval. If, for some reason, such as an adjustment in the NE's time-of-day clock, the number of seconds elapsed exceeds the maximum value, then the maximum value will be returned.
1.3.6.1.4.1.2636.3.73.1.1.2.1.1.1Gauge32 (0..900)read-onlycurrent
jnxoptIfPerfMonCurDayTimeElapsed
OBJECT-TYPE
Number of seconds elapsed in the current 24-hour interval performance monitoring period. If, for some reason, such as an adjustment in the NE time-of-day clock, the number of seconds elapsed exceeds the maximum value, then the maximum value will be returned.
1.3.6.1.4.1.2636.3.73.1.1.2.1.1.2Gauge32 (0..86400)read-onlycurrent
jnxoptIfPerfMonIntervalNumIntervals
OBJECT-TYPE
The number of 15-minute intervals for which performance monitoring data is available. The number is the same for all the associated sub layers of the interface. An optical interface must be capable of supporting at least n intervals, where n is defined as follows: The minimum value of n is 4. The default of n is 32. The maximum value of n is 96. The value of this object will be n unless performance monitoring was (re-)started for the interface within the last (n*15) minutes, in which case the value will be the number of complete 15-minute intervals since measurement was (re-)started.
1.3.6.1.4.1.2636.3.73.1.1.2.1.1.3Unsigned32 (0..96)read-onlycurrent
jnxoptIfPerfMonIntervalNumInvalidIntervals
OBJECT-TYPE
The number of intervals in the range from 0 to jnxoptIfPerfMonIntervalNumIntervals for which no performance monitoring data is available and/or the data is invalid.
1.3.6.1.4.1.2636.3.73.1.1.2.1.1.4Unsigned32 (0..96)read-onlycurrent
jnxoptIfOTSn
OBJECT-IDENTITY
1.3.6.1.4.1.2636.3.73.1.1.3
jnxoptIfOTSnConfigTable
OBJECT-TYPE
A table of OTSn configuration information.
1.3.6.1.4.1.2636.3.73.1.1.3.1not-accessiblecurrent
jnxoptIfOTSnConfigEntry
OBJECT-TYPE
A conceptual row that contains OTSn configuration information of an interface.
1.3.6.1.4.1.2636.3.73.1.1.3.1.1not-accessiblecurrent
jnxoptIfOTSnDirectionality
OBJECT-TYPE
Indicates the directionality of the entity.
1.3.6.1.4.1.2636.3.73.1.1.3.1.1.1JnxoptIfDirectionalityread-onlycurrent
jnxoptIfOTSnAprStatus
OBJECT-TYPE
This attribute indicates the status of the Automatic Power Reduction (APR) function of the entity. Valid values are 'on' and 'off'.
1.3.6.1.4.1.2636.3.73.1.1.3.1.1.2SnmpAdminStringread-onlycurrent
jnxoptIfOTSnAprControl
OBJECT-TYPE
This object is a UTF-8 encoded string that specifies Automatic Power Reduction (APR) control actions requested of this entity (when written) and that returns the current APR control state of this entity (when read). The values are implementation-defined. Any implementation that instantiates this object must document the set of values that it allows to be written, the set of values that it will return, and what each of those values means.
1.3.6.1.4.1.2636.3.73.1.1.3.1.1.3SnmpAdminStringread-writecurrent
jnxoptIfOTSnTraceIdentifierTransmitted
OBJECT-TYPE
The trace identifier transmitted. This object is applicable when jnxoptIfOTSnDirectionality has the value source(2) or bidirectional(3). This object does not apply to reduced-capability systems (i.e., those for which jnxoptIfOTMnReduced has the value true(1)) or at IrDI interfaces (i.e., when jnxoptIfOTMnInterfaceType field 1 has the value 'IrDI'). If no value is ever set by a management entity for the object jnxoptIfOTSnTraceIdentifierTransmitted, system-specific default value will be used. Any implementation that instantiates this object must document the system-specific default value or how it is derived.
1.3.6.1.4.1.2636.3.73.1.1.3.1.1.4JnxoptIfTxTIread-writecurrent
jnxoptIfOTSnDAPIExpected
OBJECT-TYPE
The DAPI expected by the receiver. This object is applicable when jnxoptIfOTSnDirectionality has the value sink(1) or bidirectional(3). It has no effect if jnxoptIfOTSnTIMDetMode has the value off(1) or sapi(3). This object does not apply to reduced-capability systems (i.e., those for which jnxoptIfOTMnReduced has the value true(1)) or at IrDI interfaces (i.e., when jnxoptIfOTMnInterfaceType field 1 has the value 'IrDI').
1.3.6.1.4.1.2636.3.73.1.1.3.1.1.5JnxoptIfExDAPIread-writecurrent
jnxoptIfOTSnSAPIExpected
OBJECT-TYPE
The SAPI expected by the receiver. This object is applicable when jnxoptIfOTSnDirectionality has the value sink(1) or bidirectional(3). It has no effect if jnxoptIfOTSnTIMDetMode has the value off(1) or dapi(2). This object does not apply to reduced-capability systems (i.e., those for which jnxoptIfOTMnReduced has the value true(1)) or at IrDI interfaces (i.e., when jnxoptIfOTMnInterfaceType field 1 has the value 'IrDI').
1.3.6.1.4.1.2636.3.73.1.1.3.1.1.6JnxoptIfExSAPIread-writecurrent
jnxoptIfOTSnTraceIdentifierAccepted
OBJECT-TYPE
The actual trace identifier received. This object is applicable when jnxoptIfOTSnDirectionality has the value sink(1) or bidirectional(3). Its value is unspecified if jnxoptIfOTSnCurrentStatus has either or both of the losO(5) and los(6) bits set. This object does not apply to reduced-capability systems (i.e., those for which jnxoptIfOTMnReduced has the value true(1)) or at IrDI interfaces (i.e., when jnxoptIfOTMnInterfaceType field 1 has the value 'IrDI').
1.3.6.1.4.1.2636.3.73.1.1.3.1.1.7JnxoptIfAcTIread-onlycurrent
jnxoptIfOTSnTIMDetMode
OBJECT-TYPE
Indicates the mode of the Trace Identifier Mismatch (TIM) Detection function. This object is applicable when jnxoptIfOTSnDirectionality has the value sink(1) or bidirectional(3). The default value is off(1). This object does not apply to reduced-capability systems (i.e., those for which jnxoptIfOTMnReduced has the value true(1)) or at IrDI interfaces (i.e., when jnxoptIfOTMnInterfaceType field 1 has the value 'IrDI'). The default value of this object is off(1).
1.3.6.1.4.1.2636.3.73.1.1.3.1.1.8JnxoptIfTIMDetModeread-writecurrent
jnxoptIfOTSnTIMActEnabled
OBJECT-TYPE
Indicates whether the Trace Identifier Mismatch (TIM) Consequent Action function is enabled. This object is applicable when jnxoptIfOTSnDirectionality has the value sink(1) or bidirectional(3). It has no effect when the value of jnxoptIfOTSnTIMDetMode is off(1). This object does not apply to reduced-capability systems (i.e., those for which jnxoptIfOTMnReduced has the value true(1)) or at IrDI interfaces (i.e., when jnxoptIfOTMnInterfaceType field 1 has the value 'IrDI'). The default value of this object is false(2).
1.3.6.1.4.1.2636.3.73.1.1.3.1.1.9TruthValueread-writecurrent
jnxoptIfOTSnCurrentStatus
OBJECT-TYPE
Indicates the defect condition of the entity, if any. This object is applicable when jnxoptIfOTSnDirectionality has the value sink(1) or bidirectional(3). In reduced-capability systems or at IrDI interfaces the only bit position that may be set is los(6).
1.3.6.1.4.1.2636.3.73.1.1.3.1.1.10Bits {bdiP(0), bdiO(1), bdi(2), tim(3), losP(4), losO(5), los(6)}read-onlycurrent
jnxoptIfOTSnSinkCurrentTable
OBJECT-TYPE
A table of OTSn sink performance monitoring information for the current 15-minute interval.
1.3.6.1.4.1.2636.3.73.1.1.3.2not-accessiblecurrent
jnxoptIfOTSnSinkCurrentEntry
OBJECT-TYPE
A conceptual row that contains OTSn sink performance monitoring information of an interface for the current 15-minute interval.
1.3.6.1.4.1.2636.3.73.1.1.3.2.1not-accessiblecurrent
jnxoptIfOTSnSinkCurrentSuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.4.1.2636.3.73.1.1.3.2.1.1TruthValueread-onlycurrent
jnxoptIfOTSnSinkCurrentInputPower
OBJECT-TYPE
The optical power monitored at the input.
1.3.6.1.4.1.2636.3.73.1.1.3.2.1.2Integer32read-onlycurrent
jnxoptIfOTSnSinkCurrentLowInputPower
OBJECT-TYPE
The lowest optical power monitored at the input during the current 15-minute interval.
1.3.6.1.4.1.2636.3.73.1.1.3.2.1.3Integer32read-onlycurrent
jnxoptIfOTSnSinkCurrentHighInputPower
OBJECT-TYPE
The highest optical power monitored at the input during the current 15-minute interval.
1.3.6.1.4.1.2636.3.73.1.1.3.2.1.4Integer32read-onlycurrent
jnxoptIfOTSnSinkCurrentLowerInputPowerThreshold
OBJECT-TYPE
The lower limit threshold on input power. If jnxoptIfOTSnSinkCurrentInputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.4.1.2636.3.73.1.1.3.2.1.5Integer32read-writecurrent
jnxoptIfOTSnSinkCurrentUpperInputPowerThreshold
OBJECT-TYPE
The upper limit threshold on input power. If jnxoptIfOTSnSinkCurrentInputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.4.1.2636.3.73.1.1.3.2.1.6Integer32read-writecurrent
jnxoptIfOTSnSinkCurrentOutputPower
OBJECT-TYPE
The optical power monitored at the output.
1.3.6.1.4.1.2636.3.73.1.1.3.2.1.7Integer32read-onlycurrent
jnxoptIfOTSnSinkCurrentLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output during the current 15-minute interval.
1.3.6.1.4.1.2636.3.73.1.1.3.2.1.8Integer32read-onlycurrent
jnxoptIfOTSnSinkCurrentHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output during the current 15-minute interval.
1.3.6.1.4.1.2636.3.73.1.1.3.2.1.9Integer32read-onlycurrent
jnxoptIfOTSnSinkCurrentLowerOutputPowerThreshold
OBJECT-TYPE
The lower limit threshold on output power. If jnxoptIfOTSnSinkCurrentOutputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.4.1.2636.3.73.1.1.3.2.1.10Integer32read-writecurrent
jnxoptIfOTSnSinkCurrentUpperOutputPowerThreshold
OBJECT-TYPE
The upper limit threshold on output power. If jnxoptIfOTSnSinkCurrentOutputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.4.1.2636.3.73.1.1.3.2.1.11Integer32read-writecurrent
jnxoptIfOTSnSinkIntervalTable
OBJECT-TYPE
A table of historical OTSn sink performance monitoring information.
1.3.6.1.4.1.2636.3.73.1.1.3.3not-accessiblecurrent
jnxoptIfOTSnSinkIntervalEntry
OBJECT-TYPE
A conceptual row that contains OTSn sink performance monitoring information of an interface during a particular historical interval.
1.3.6.1.4.1.2636.3.73.1.1.3.3.1not-accessiblecurrent
jnxoptIfOTSnSinkIntervalNumber
OBJECT-TYPE
Uniquely identifies the interval.
1.3.6.1.4.1.2636.3.73.1.1.3.3.1.1JnxoptIfIntervalNumbernot-accessiblecurrent
jnxoptIfOTSnSinkIntervalSuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.4.1.2636.3.73.1.1.3.3.1.2TruthValueread-onlycurrent
jnxoptIfOTSnSinkIntervalLastInputPower
OBJECT-TYPE
The last optical power monitored at the input during the interval.
1.3.6.1.4.1.2636.3.73.1.1.3.3.1.3Integer32read-onlycurrent
jnxoptIfOTSnSinkIntervalLowInputPower
OBJECT-TYPE
The lowest optical power monitored at the input during the interval.
1.3.6.1.4.1.2636.3.73.1.1.3.3.1.4Integer32read-onlycurrent
jnxoptIfOTSnSinkIntervalHighInputPower
OBJECT-TYPE
The highest optical power monitored at the input during the interval.
1.3.6.1.4.1.2636.3.73.1.1.3.3.1.5Integer32read-onlycurrent
jnxoptIfOTSnSinkIntervalLastOutputPower
OBJECT-TYPE
The last optical power monitored at the output during the interval.
1.3.6.1.4.1.2636.3.73.1.1.3.3.1.6Integer32read-onlycurrent
jnxoptIfOTSnSinkIntervalLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output during the interval.
1.3.6.1.4.1.2636.3.73.1.1.3.3.1.7Integer32read-onlycurrent
jnxoptIfOTSnSinkIntervalHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output during the interval.
1.3.6.1.4.1.2636.3.73.1.1.3.3.1.8Integer32read-onlycurrent
jnxoptIfOTSnSinkCurDayTable
OBJECT-TYPE
A table of OTSn sink performance monitoring information for the current 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.3.4not-accessiblecurrent
jnxoptIfOTSnSinkCurDayEntry
OBJECT-TYPE
A conceptual row that contains OTSn sink performance monitoring information of an interface for the current 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.3.4.1not-accessiblecurrent
jnxoptIfOTSnSinkCurDaySuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.4.1.2636.3.73.1.1.3.4.1.1TruthValueread-onlycurrent
jnxoptIfOTSnSinkCurDayLowInputPower
OBJECT-TYPE
The lowest optical power monitored at the input during the current 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.3.4.1.2Integer32read-onlycurrent
jnxoptIfOTSnSinkCurDayHighInputPower
OBJECT-TYPE
The highest optical power monitored at the input during the current 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.3.4.1.3Integer32read-onlycurrent
jnxoptIfOTSnSinkCurDayLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output during the current 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.3.4.1.4Integer32read-onlycurrent
jnxoptIfOTSnSinkCurDayHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output during the current 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.3.4.1.5Integer32read-onlycurrent
jnxoptIfOTSnSinkPrevDayTable
OBJECT-TYPE
A table of OTSn sink performance monitoring information for the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.3.5not-accessiblecurrent
jnxoptIfOTSnSinkPrevDayEntry
OBJECT-TYPE
A conceptual row that contains OTSn sink performance monitoring information of an interface for the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.3.5.1not-accessiblecurrent
jnxoptIfOTSnSinkPrevDaySuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.4.1.2636.3.73.1.1.3.5.1.1TruthValueread-onlycurrent
jnxoptIfOTSnSinkPrevDayLastInputPower
OBJECT-TYPE
The last optical power monitored at the input during the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.3.5.1.2Integer32read-onlycurrent
jnxoptIfOTSnSinkPrevDayLowInputPower
OBJECT-TYPE
The lowest optical power monitored at the input during the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.3.5.1.3Integer32read-onlycurrent
jnxoptIfOTSnSinkPrevDayHighInputPower
OBJECT-TYPE
The highest optical power monitored at the input during the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.3.5.1.4Integer32read-onlycurrent
jnxoptIfOTSnSinkPrevDayLastOutputPower
OBJECT-TYPE
The last optical power monitored at the output during the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.3.5.1.5Integer32read-onlycurrent
jnxoptIfOTSnSinkPrevDayLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output during the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.3.5.1.6Integer32read-onlycurrent
jnxoptIfOTSnSinkPrevDayHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output during the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.3.5.1.7Integer32read-onlycurrent
jnxoptIfOTSnSrcCurrentTable
OBJECT-TYPE
A table of OTSn source performance monitoring information for the current 15-minute interval.
1.3.6.1.4.1.2636.3.73.1.1.3.6not-accessiblecurrent
jnxoptIfOTSnSrcCurrentEntry
OBJECT-TYPE
A conceptual row that contains OTSn source performance monitoring information of an interface for the current 15-minute interval.
1.3.6.1.4.1.2636.3.73.1.1.3.6.1not-accessiblecurrent
jnxoptIfOTSnSrcCurrentSuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.4.1.2636.3.73.1.1.3.6.1.1TruthValueread-onlycurrent
jnxoptIfOTSnSrcCurrentOutputPower
OBJECT-TYPE
The optical power monitored at the output.
1.3.6.1.4.1.2636.3.73.1.1.3.6.1.2Integer32read-onlycurrent
jnxoptIfOTSnSrcCurrentLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output during the current 15-minute interval.
1.3.6.1.4.1.2636.3.73.1.1.3.6.1.3Integer32read-onlycurrent
jnxoptIfOTSnSrcCurrentHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output during the current 15-minute interval.
1.3.6.1.4.1.2636.3.73.1.1.3.6.1.4Integer32read-onlycurrent
jnxoptIfOTSnSrcCurrentLowerOutputPowerThreshold
OBJECT-TYPE
The lower limit threshold on output power. If jnxoptIfOTSnSrcCurrentOutputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.4.1.2636.3.73.1.1.3.6.1.5Integer32read-writecurrent
jnxoptIfOTSnSrcCurrentUpperOutputPowerThreshold
OBJECT-TYPE
The upper limit threshold on output power. If jnxoptIfOTSnSrcCurrentOutputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.4.1.2636.3.73.1.1.3.6.1.6Integer32read-writecurrent
jnxoptIfOTSnSrcCurrentInputPower
OBJECT-TYPE
The optical power monitored at the input.
1.3.6.1.4.1.2636.3.73.1.1.3.6.1.7Integer32read-onlycurrent
jnxoptIfOTSnSrcCurrentLowInputPower
OBJECT-TYPE
The lowest optical power monitored at the input during the current 15-minute interval.
1.3.6.1.4.1.2636.3.73.1.1.3.6.1.8Integer32read-onlycurrent
jnxoptIfOTSnSrcCurrentHighInputPower
OBJECT-TYPE
The highest optical power monitored at the input during the current 15-minute interval.
1.3.6.1.4.1.2636.3.73.1.1.3.6.1.9Integer32read-onlycurrent
jnxoptIfOTSnSrcCurrentLowerInputPowerThreshold
OBJECT-TYPE
The lower limit threshold on input power. If jnxoptIfOTSnSrcCurrentInputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.4.1.2636.3.73.1.1.3.6.1.10Integer32read-writecurrent
jnxoptIfOTSnSrcCurrentUpperInputPowerThreshold
OBJECT-TYPE
The upper limit threshold on input power. If jnxoptIfOTSnSrcCurrentInputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.4.1.2636.3.73.1.1.3.6.1.11Integer32read-writecurrent
jnxoptIfOTSnSrcIntervalTable
OBJECT-TYPE
A table of historical OTSn source performance monitoring information.
1.3.6.1.4.1.2636.3.73.1.1.3.7not-accessiblecurrent
jnxoptIfOTSnSrcIntervalEntry
OBJECT-TYPE
A conceptual row that contains OTSn source performance monitoring information of an interface during a particular historical interval.
1.3.6.1.4.1.2636.3.73.1.1.3.7.1not-accessiblecurrent
jnxoptIfOTSnSrcIntervalNumber
OBJECT-TYPE
Uniquely identifies the interval.
1.3.6.1.4.1.2636.3.73.1.1.3.7.1.1JnxoptIfIntervalNumbernot-accessiblecurrent
jnxoptIfOTSnSrcIntervalSuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.4.1.2636.3.73.1.1.3.7.1.2TruthValueread-onlycurrent
jnxoptIfOTSnSrcIntervalLastOutputPower
OBJECT-TYPE
The last optical power monitored at the output during the interval.
1.3.6.1.4.1.2636.3.73.1.1.3.7.1.3Integer32read-onlycurrent
jnxoptIfOTSnSrcIntervalLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output during the interval.
1.3.6.1.4.1.2636.3.73.1.1.3.7.1.4Integer32read-onlycurrent
jnxoptIfOTSnSrcIntervalHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output during the interval.
1.3.6.1.4.1.2636.3.73.1.1.3.7.1.5Integer32read-onlycurrent
jnxoptIfOTSnSrcIntervalLastInputPower
OBJECT-TYPE
The last optical power monitored at the input during the interval.
1.3.6.1.4.1.2636.3.73.1.1.3.7.1.6Integer32read-onlycurrent
jnxoptIfOTSnSrcIntervalLowInputPower
OBJECT-TYPE
The lowest optical power monitored at the input during the interval.
1.3.6.1.4.1.2636.3.73.1.1.3.7.1.7Integer32read-onlycurrent
jnxoptIfOTSnSrcIntervalHighInputPower
OBJECT-TYPE
The highest optical power monitored at the input during the interval.
1.3.6.1.4.1.2636.3.73.1.1.3.7.1.8Integer32read-onlycurrent
jnxoptIfOTSnSrcCurDayTable
OBJECT-TYPE
A table of OTSn source performance monitoring information for the current 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.3.8not-accessiblecurrent
jnxoptIfOTSnSrcCurDayEntry
OBJECT-TYPE
A conceptual row that contains OTSn source performance monitoring information of an interface for the current 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.3.8.1not-accessiblecurrent
jnxoptIfOTSnSrcCurDaySuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.4.1.2636.3.73.1.1.3.8.1.1TruthValueread-onlycurrent
jnxoptIfOTSnSrcCurDayLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output during the current 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.3.8.1.2Integer32read-onlycurrent
jnxoptIfOTSnSrcCurDayHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output during the current 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.3.8.1.3Integer32read-onlycurrent
jnxoptIfOTSnSrcCurDayLowInputPower
OBJECT-TYPE
The lowest optical power monitored at the input during the current 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.3.8.1.4Integer32read-onlycurrent
jnxoptIfOTSnSrcCurDayHighInputPower
OBJECT-TYPE
The highest optical power monitored at the input during the current 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.3.8.1.5Integer32read-onlycurrent
jnxoptIfOTSnSrcPrevDayTable
OBJECT-TYPE
A table of OTSn source performance monitoring information for the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.3.9not-accessiblecurrent
jnxoptIfOTSnSrcPrevDayEntry
OBJECT-TYPE
A conceptual row that contains OTSn source performance monitoring information of an interface for the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.3.9.1not-accessiblecurrent
jnxoptIfOTSnSrcPrevDaySuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.4.1.2636.3.73.1.1.3.9.1.1TruthValueread-onlycurrent
jnxoptIfOTSnSrcPrevDayLastOutputPower
OBJECT-TYPE
The last optical power monitored at the output during the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.3.9.1.2Integer32read-onlycurrent
jnxoptIfOTSnSrcPrevDayLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output during the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.3.9.1.3Integer32read-onlycurrent
jnxoptIfOTSnSrcPrevDayHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output during the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.3.9.1.4Integer32read-onlycurrent
jnxoptIfOTSnSrcPrevDayLastInputPower
OBJECT-TYPE
The last optical power monitored at the input during the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.3.9.1.5Integer32read-onlycurrent
jnxoptIfOTSnSrcPrevDayLowInputPower
OBJECT-TYPE
The lowest optical power monitored at the input during the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.3.9.1.6Integer32read-onlycurrent
jnxoptIfOTSnSrcPrevDayHighInputPower
OBJECT-TYPE
The highest optical power monitored at the input during the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.3.9.1.7Integer32read-onlycurrent
jnxoptIfOMSn
OBJECT-IDENTITY
1.3.6.1.4.1.2636.3.73.1.1.4
jnxoptIfOMSnConfigTable
OBJECT-TYPE
A table of OMSn configuration information.
1.3.6.1.4.1.2636.3.73.1.1.4.1not-accessiblecurrent
jnxoptIfOMSnConfigEntry
OBJECT-TYPE
A conceptual row that contains OMSn configuration information of an interface.
1.3.6.1.4.1.2636.3.73.1.1.4.1.1not-accessiblecurrent
jnxoptIfOMSnDirectionality
OBJECT-TYPE
Indicates the directionality of the entity.
1.3.6.1.4.1.2636.3.73.1.1.4.1.1.1JnxoptIfDirectionalityread-onlycurrent
jnxoptIfOMSnCurrentStatus
OBJECT-TYPE
Indicates the defect condition of the entity, if any. This object is applicable only to full capability systems whose interface type is IaDI and for which jnxoptIfOMSnDirectionality has the value sink(1) or bidirectional(3).
1.3.6.1.4.1.2636.3.73.1.1.4.1.1.2Bits {ssfP(0), ssfO(1), ssf(2), bdiP(3), bdiO(4), bdi(5), losP(6)}read-onlycurrent
jnxoptIfOMSnSinkCurrentTable
OBJECT-TYPE
A table of OMSn sink performance monitoring information for the current 15-minute interval.
1.3.6.1.4.1.2636.3.73.1.1.4.2not-accessiblecurrent
jnxoptIfOMSnSinkCurrentEntry
OBJECT-TYPE
A conceptual row that contains OMSn sink performance monitoring information of an interface for the current 15-minute interval.
1.3.6.1.4.1.2636.3.73.1.1.4.2.1not-accessiblecurrent
jnxoptIfOMSnSinkCurrentSuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.4.1.2636.3.73.1.1.4.2.1.1TruthValueread-onlycurrent
jnxoptIfOMSnSinkCurrentAggregatedInputPower
OBJECT-TYPE
The aggregated optical power of all the DWDM input channels.
1.3.6.1.4.1.2636.3.73.1.1.4.2.1.2Integer32read-onlycurrent
jnxoptIfOMSnSinkCurrentLowAggregatedInputPower
OBJECT-TYPE
The lowest aggregated optical power of all the DWDM input channels during the current 15-minute interval.
1.3.6.1.4.1.2636.3.73.1.1.4.2.1.3Integer32read-onlycurrent
jnxoptIfOMSnSinkCurrentHighAggregatedInputPower
OBJECT-TYPE
The highest aggregated optical power of all the DWDM input channels during the current 15-minute interval.
1.3.6.1.4.1.2636.3.73.1.1.4.2.1.4Integer32read-onlycurrent
jnxoptIfOMSnSinkCurrentLowerInputPowerThreshold
OBJECT-TYPE
The lower limit threshold on aggregated input power. If jnxoptIfOMSnSinkCurrentAggregatedInputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.4.1.2636.3.73.1.1.4.2.1.5Integer32read-writecurrent
jnxoptIfOMSnSinkCurrentUpperInputPowerThreshold
OBJECT-TYPE
The upper limit threshold on aggregated input power. If jnxoptIfOMSnSinkCurrentAggregatedInputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.4.1.2636.3.73.1.1.4.2.1.6Integer32read-writecurrent
jnxoptIfOMSnSinkCurrentOutputPower
OBJECT-TYPE
The optical power monitored at the output.
1.3.6.1.4.1.2636.3.73.1.1.4.2.1.7Integer32read-onlycurrent
jnxoptIfOMSnSinkCurrentLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output during the current 15-minute interval.
1.3.6.1.4.1.2636.3.73.1.1.4.2.1.8Integer32read-onlycurrent
jnxoptIfOMSnSinkCurrentHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output during the current 15-minute interval.
1.3.6.1.4.1.2636.3.73.1.1.4.2.1.9Integer32read-onlycurrent
jnxoptIfOMSnSinkCurrentLowerOutputPowerThreshold
OBJECT-TYPE
The lower limit threshold on output power. If jnxoptIfOMSnSinkCurrentOutputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.4.1.2636.3.73.1.1.4.2.1.10Integer32read-writecurrent
jnxoptIfOMSnSinkCurrentUpperOutputPowerThreshold
OBJECT-TYPE
The upper limit threshold on output power. If jnxoptIfOMSnSinkCurrentOutputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.4.1.2636.3.73.1.1.4.2.1.11Integer32read-writecurrent
jnxoptIfOMSnSinkIntervalTable
OBJECT-TYPE
A table of historical OMSn sink performance monitoring information.
1.3.6.1.4.1.2636.3.73.1.1.4.3not-accessiblecurrent
jnxoptIfOMSnSinkIntervalEntry
OBJECT-TYPE
A conceptual row that contains OMSn sink performance monitoring information of an interface during a particular historical interval.
1.3.6.1.4.1.2636.3.73.1.1.4.3.1not-accessiblecurrent
jnxoptIfOMSnSinkIntervalNumber
OBJECT-TYPE
Uniquely identifies the interval.
1.3.6.1.4.1.2636.3.73.1.1.4.3.1.1JnxoptIfIntervalNumbernot-accessiblecurrent
jnxoptIfOMSnSinkIntervalSuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.4.1.2636.3.73.1.1.4.3.1.2TruthValueread-onlycurrent
jnxoptIfOMSnSinkIntervalLastAggregatedInputPower
OBJECT-TYPE
The last aggregated optical power of all the DWDM input channels during the interval.
1.3.6.1.4.1.2636.3.73.1.1.4.3.1.3Integer32read-onlycurrent
jnxoptIfOMSnSinkIntervalLowAggregatedInputPower
OBJECT-TYPE
The lowest aggregated optical power of all the DWDM input channels during the interval.
1.3.6.1.4.1.2636.3.73.1.1.4.3.1.4Integer32read-onlycurrent
jnxoptIfOMSnSinkIntervalHighAggregatedInputPower
OBJECT-TYPE
The highest aggregated optical power of all the DWDM input channels during the interval.
1.3.6.1.4.1.2636.3.73.1.1.4.3.1.5Integer32read-onlycurrent
jnxoptIfOMSnSinkIntervalLastOutputPower
OBJECT-TYPE
The last optical power at the output during the interval.
1.3.6.1.4.1.2636.3.73.1.1.4.3.1.6Integer32read-onlycurrent
jnxoptIfOMSnSinkIntervalLowOutputPower
OBJECT-TYPE
The lowest optical power at the output during the interval.
1.3.6.1.4.1.2636.3.73.1.1.4.3.1.7Integer32read-onlycurrent
jnxoptIfOMSnSinkIntervalHighOutputPower
OBJECT-TYPE
The highest optical power at the output during the interval.
1.3.6.1.4.1.2636.3.73.1.1.4.3.1.8Integer32read-onlycurrent
jnxoptIfOMSnSinkCurDayTable
OBJECT-TYPE
A table of OMSn sink performance monitoring information for the current 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.4.4not-accessiblecurrent
jnxoptIfOMSnSinkCurDayEntry
OBJECT-TYPE
A conceptual row that contains OMSn sink performance monitoring information of an interface for the current 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.4.4.1not-accessiblecurrent
jnxoptIfOMSnSinkCurDaySuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.4.1.2636.3.73.1.1.4.4.1.1TruthValueread-onlycurrent
jnxoptIfOMSnSinkCurDayLowAggregatedInputPower
OBJECT-TYPE
The lowest aggregated optical power of all the DWDM input channels during the current 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.4.4.1.2Integer32read-onlycurrent
jnxoptIfOMSnSinkCurDayHighAggregatedInputPower
OBJECT-TYPE
The highest aggregated optical power of all the DWDM input channels during the current 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.4.4.1.3Integer32read-onlycurrent
jnxoptIfOMSnSinkCurDayLowOutputPower
OBJECT-TYPE
The lowest optical power at the output during the current 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.4.4.1.4Integer32read-onlycurrent
jnxoptIfOMSnSinkCurDayHighOutputPower
OBJECT-TYPE
The highest optical power at the output during the current 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.4.4.1.5Integer32read-onlycurrent
jnxoptIfOMSnSinkPrevDayTable
OBJECT-TYPE
A table of OMSn sink performance monitoring information for the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.4.5not-accessiblecurrent
jnxoptIfOMSnSinkPrevDayEntry
OBJECT-TYPE
A conceptual row that contains OMSn sink performance monitoring information of an interface for the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.4.5.1not-accessiblecurrent
jnxoptIfOMSnSinkPrevDaySuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.4.1.2636.3.73.1.1.4.5.1.1TruthValueread-onlycurrent
jnxoptIfOMSnSinkPrevDayLastAggregatedInputPower
OBJECT-TYPE
The last aggregated optical power of all the DWDM input channels during the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.4.5.1.2Integer32read-onlycurrent
jnxoptIfOMSnSinkPrevDayLowAggregatedInputPower
OBJECT-TYPE
The lowest aggregated optical power of all the DWDM input channels during the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.4.5.1.3Integer32read-onlycurrent
jnxoptIfOMSnSinkPrevDayHighAggregatedInputPower
OBJECT-TYPE
The highest aggregated optical power of all the DWDM input channels during the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.4.5.1.4Integer32read-onlycurrent
jnxoptIfOMSnSinkPrevDayLastOutputPower
OBJECT-TYPE
The last optical power at the output during the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.4.5.1.5Integer32read-onlycurrent
jnxoptIfOMSnSinkPrevDayLowOutputPower
OBJECT-TYPE
The lowest optical power at the output during the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.4.5.1.6Integer32read-onlycurrent
jnxoptIfOMSnSinkPrevDayHighOutputPower
OBJECT-TYPE
The highest optical power at the output during the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.4.5.1.7Integer32read-onlycurrent
jnxoptIfOMSnSrcCurrentTable
OBJECT-TYPE
A table of OMSn source performance monitoring information for the current 15-minute interval.
1.3.6.1.4.1.2636.3.73.1.1.4.6not-accessiblecurrent
jnxoptIfOMSnSrcCurrentEntry
OBJECT-TYPE
A conceptual row that contains OMSn source performance monitoring information of an interface for the current 15-minute interval.
1.3.6.1.4.1.2636.3.73.1.1.4.6.1not-accessiblecurrent
jnxoptIfOMSnSrcCurrentSuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.4.1.2636.3.73.1.1.4.6.1.1TruthValueread-onlycurrent
jnxoptIfOMSnSrcCurrentOutputPower
OBJECT-TYPE
The optical power monitored at the output.
1.3.6.1.4.1.2636.3.73.1.1.4.6.1.2Integer32read-onlycurrent
jnxoptIfOMSnSrcCurrentLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output during the current 15-minute interval.
1.3.6.1.4.1.2636.3.73.1.1.4.6.1.3Integer32read-onlycurrent
jnxoptIfOMSnSrcCurrentHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output during the current 15-minute interval.
1.3.6.1.4.1.2636.3.73.1.1.4.6.1.4Integer32read-onlycurrent
jnxoptIfOMSnSrcCurrentLowerOutputPowerThreshold
OBJECT-TYPE
The lower limit threshold on output power. If jnxoptIfOMSnSrcCurrentOutputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.4.1.2636.3.73.1.1.4.6.1.5Integer32read-writecurrent
jnxoptIfOMSnSrcCurrentUpperOutputPowerThreshold
OBJECT-TYPE
The upper limit threshold on output power. If jnxoptIfOMSnSrcCurrentOutputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.4.1.2636.3.73.1.1.4.6.1.6Integer32read-writecurrent
jnxoptIfOMSnSrcCurrentAggregatedInputPower
OBJECT-TYPE
The aggregated optical power at the input.
1.3.6.1.4.1.2636.3.73.1.1.4.6.1.7Integer32read-onlycurrent
jnxoptIfOMSnSrcCurrentLowAggregatedInputPower
OBJECT-TYPE
The lowest aggregated optical power at the input during the current 15-minute interval.
1.3.6.1.4.1.2636.3.73.1.1.4.6.1.8Integer32read-onlycurrent
jnxoptIfOMSnSrcCurrentHighAggregatedInputPower
OBJECT-TYPE
The highest aggregated optical power at the input during the current 15-minute interval.
1.3.6.1.4.1.2636.3.73.1.1.4.6.1.9Integer32read-onlycurrent
jnxoptIfOMSnSrcCurrentLowerInputPowerThreshold
OBJECT-TYPE
The lower limit threshold on aggregated input power. If jnxoptIfOMSnSrcCurrentAggregatedInputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.4.1.2636.3.73.1.1.4.6.1.10Integer32read-writecurrent
jnxoptIfOMSnSrcCurrentUpperInputPowerThreshold
OBJECT-TYPE
The upper limit threshold on aggregated input power. If jnxoptIfOMSnSrcCurrentAggregatedInputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.4.1.2636.3.73.1.1.4.6.1.11Integer32read-writecurrent
jnxoptIfOMSnSrcIntervalTable
OBJECT-TYPE
A table of historical OMSn source performance monitoring information.
1.3.6.1.4.1.2636.3.73.1.1.4.7not-accessiblecurrent
jnxoptIfOMSnSrcIntervalEntry
OBJECT-TYPE
A conceptual row that contains OMSn source performance monitoring information of an interface during a particular historical interval.
1.3.6.1.4.1.2636.3.73.1.1.4.7.1not-accessiblecurrent
jnxoptIfOMSnSrcIntervalNumber
OBJECT-TYPE
Uniquely identifies the interval.
1.3.6.1.4.1.2636.3.73.1.1.4.7.1.1JnxoptIfIntervalNumbernot-accessiblecurrent
jnxoptIfOMSnSrcIntervalSuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.4.1.2636.3.73.1.1.4.7.1.2TruthValueread-onlycurrent
jnxoptIfOMSnSrcIntervalLastOutputPower
OBJECT-TYPE
The last optical power monitored at the output during the interval.
1.3.6.1.4.1.2636.3.73.1.1.4.7.1.3Integer32read-onlycurrent
jnxoptIfOMSnSrcIntervalLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output during the interval.
1.3.6.1.4.1.2636.3.73.1.1.4.7.1.4Integer32read-onlycurrent
jnxoptIfOMSnSrcIntervalHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output during the interval.
1.3.6.1.4.1.2636.3.73.1.1.4.7.1.5Integer32read-onlycurrent
jnxoptIfOMSnSrcIntervalLastAggregatedInputPower
OBJECT-TYPE
The last aggregated optical power at the input during the interval.
1.3.6.1.4.1.2636.3.73.1.1.4.7.1.6Integer32read-onlycurrent
jnxoptIfOMSnSrcIntervalLowAggregatedInputPower
OBJECT-TYPE
The lowest aggregated optical power at the input during the interval.
1.3.6.1.4.1.2636.3.73.1.1.4.7.1.7Integer32read-onlycurrent
jnxoptIfOMSnSrcIntervalHighAggregatedInputPower
OBJECT-TYPE
The highest aggregated optical power at the input during the interval.
1.3.6.1.4.1.2636.3.73.1.1.4.7.1.8Integer32read-onlycurrent
jnxoptIfOMSnSrcCurDayTable
OBJECT-TYPE
A table of OMSn source performance monitoring information for the current 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.4.8not-accessiblecurrent
jnxoptIfOMSnSrcCurDayEntry
OBJECT-TYPE
A conceptual row that contains OMSn source performance monitoring information of an interface for the current 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.4.8.1not-accessiblecurrent
jnxoptIfOMSnSrcCurDaySuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.4.1.2636.3.73.1.1.4.8.1.1TruthValueread-onlycurrent
jnxoptIfOMSnSrcCurDayLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output during the current 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.4.8.1.2Integer32read-onlycurrent
jnxoptIfOMSnSrcCurDayHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output during the current 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.4.8.1.3Integer32read-onlycurrent
jnxoptIfOMSnSrcCurDayLowAggregatedInputPower
OBJECT-TYPE
The lowest aggregated optical power at the input during the current 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.4.8.1.4Integer32read-onlycurrent
jnxoptIfOMSnSrcCurDayHighAggregatedInputPower
OBJECT-TYPE
The highest aggregated optical power at the input during the current 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.4.8.1.5Integer32read-onlycurrent
jnxoptIfOMSnSrcPrevDayTable
OBJECT-TYPE
A table of OMSn source performance monitoring information for the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.4.9not-accessiblecurrent
jnxoptIfOMSnSrcPrevDayEntry
OBJECT-TYPE
A conceptual row that contains OMSn source performance monitoring information of an interface for the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.4.9.1not-accessiblecurrent
jnxoptIfOMSnSrcPrevDaySuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.4.1.2636.3.73.1.1.4.9.1.1TruthValueread-onlycurrent
jnxoptIfOMSnSrcPrevDayLastOutputPower
OBJECT-TYPE
The last optical power monitored at the output during the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.4.9.1.2Integer32read-onlycurrent
jnxoptIfOMSnSrcPrevDayLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output during the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.4.9.1.3Integer32read-onlycurrent
jnxoptIfOMSnSrcPrevDayHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output during the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.4.9.1.4Integer32read-onlycurrent
jnxoptIfOMSnSrcPrevDayLastAggregatedInputPower
OBJECT-TYPE
The last aggregated optical power at the input during the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.4.9.1.5Integer32read-onlycurrent
jnxoptIfOMSnSrcPrevDayLowAggregatedInputPower
OBJECT-TYPE
The lowest aggregated optical power at the input during the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.4.9.1.6Integer32read-onlycurrent
jnxoptIfOMSnSrcPrevDayHighAggregatedInputPower
OBJECT-TYPE
The highest aggregated optical power at the input during the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.4.9.1.7Integer32read-onlycurrent
jnxoptIfOChGroup
OBJECT-IDENTITY
1.3.6.1.4.1.2636.3.73.1.1.5
jnxoptIfOChGroupConfigTable
OBJECT-TYPE
A table of OChGroup configuration information.
1.3.6.1.4.1.2636.3.73.1.1.5.1not-accessiblecurrent
jnxoptIfOChGroupConfigEntry
OBJECT-TYPE
A conceptual row that contains OChGroup configuration information of an interface.
1.3.6.1.4.1.2636.3.73.1.1.5.1.1not-accessiblecurrent
jnxoptIfOChGroupDirectionality
OBJECT-TYPE
Indicates the directionality of the entity.
1.3.6.1.4.1.2636.3.73.1.1.5.1.1.1JnxoptIfDirectionalityread-onlycurrent
jnxoptIfOChGroupSinkCurrentTable
OBJECT-TYPE
A table of OChGroup sink performance monitoring information for the current 15-minute interval.
1.3.6.1.4.1.2636.3.73.1.1.5.2not-accessiblecurrent
jnxoptIfOChGroupSinkCurrentEntry
OBJECT-TYPE
A conceptual row that contains OChGroup sink performance monitoring information of an interface for the current 15-minute interval.
1.3.6.1.4.1.2636.3.73.1.1.5.2.1not-accessiblecurrent
jnxoptIfOChGroupSinkCurrentSuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.4.1.2636.3.73.1.1.5.2.1.1TruthValueread-onlycurrent
jnxoptIfOChGroupSinkCurrentAggregatedInputPower
OBJECT-TYPE
The aggregated optical power of all the DWDM input channels in the OChGroup.
1.3.6.1.4.1.2636.3.73.1.1.5.2.1.2Integer32read-onlycurrent
jnxoptIfOChGroupSinkCurrentLowAggregatedInputPower
OBJECT-TYPE
The lowest aggregated optical power of all the DWDM input channels in the OChGroup during the current 15-minute interval.
1.3.6.1.4.1.2636.3.73.1.1.5.2.1.3Integer32read-onlycurrent
jnxoptIfOChGroupSinkCurrentHighAggregatedInputPower
OBJECT-TYPE
The highest aggregated optical power of all the DWDM input channels in the OChGroup during the current 15-minute interval.
1.3.6.1.4.1.2636.3.73.1.1.5.2.1.4Integer32read-onlycurrent
jnxoptIfOChGroupSinkCurrentLowerInputPowerThreshold
OBJECT-TYPE
The lower limit threshold on aggregated input power. If jnxoptIfOChGroupSinkCurrentAggregatedInputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.4.1.2636.3.73.1.1.5.2.1.5Integer32read-writecurrent
jnxoptIfOChGroupSinkCurrentUpperInputPowerThreshold
OBJECT-TYPE
The upper limit threshold on aggregated input power. If jnxoptIfOChGroupSinkCurrentAggregatedInputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.4.1.2636.3.73.1.1.5.2.1.6Integer32read-writecurrent
jnxoptIfOChGroupSinkCurrentOutputPower
OBJECT-TYPE
The optical power monitored at the output in the OChGroup.
1.3.6.1.4.1.2636.3.73.1.1.5.2.1.7Integer32read-onlycurrent
jnxoptIfOChGroupSinkCurrentLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output in the OChGroup during the current 15-minute interval.
1.3.6.1.4.1.2636.3.73.1.1.5.2.1.8Integer32read-onlycurrent
jnxoptIfOChGroupSinkCurrentHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output in the OChGroup during the current 15-minute interval.
1.3.6.1.4.1.2636.3.73.1.1.5.2.1.9Integer32read-onlycurrent
jnxoptIfOChGroupSinkCurrentLowerOutputPowerThreshold
OBJECT-TYPE
The lower limit threshold on the output power. If jnxoptIfOChGroupSinkCurrentOutputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.4.1.2636.3.73.1.1.5.2.1.10Integer32read-writecurrent
jnxoptIfOChGroupSinkCurrentUpperOutputPowerThreshold
OBJECT-TYPE
The upper limit threshold on the output power. If jnxoptIfOChGroupSinkCurrentOutputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.4.1.2636.3.73.1.1.5.2.1.11Integer32read-writecurrent
jnxoptIfOChGroupSinkIntervalTable
OBJECT-TYPE
A table of historical OChGroup sink performance monitoring information.
1.3.6.1.4.1.2636.3.73.1.1.5.3not-accessiblecurrent
jnxoptIfOChGroupSinkIntervalEntry
OBJECT-TYPE
A conceptual row that contains OChGroup sink performance monitoring information of an interface during a particular historical interval.
1.3.6.1.4.1.2636.3.73.1.1.5.3.1not-accessiblecurrent
jnxoptIfOChGroupSinkIntervalNumber
OBJECT-TYPE
Uniquely identifies the interval.
1.3.6.1.4.1.2636.3.73.1.1.5.3.1.1JnxoptIfIntervalNumbernot-accessiblecurrent
jnxoptIfOChGroupSinkIntervalSuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.4.1.2636.3.73.1.1.5.3.1.2TruthValueread-onlycurrent
jnxoptIfOChGroupSinkIntervalLastAggregatedInputPower
OBJECT-TYPE
The last aggregated optical power of all the DWDM input channels in the OChGroup during the interval.
1.3.6.1.4.1.2636.3.73.1.1.5.3.1.3Integer32read-onlycurrent
jnxoptIfOChGroupSinkIntervalLowAggregatedInputPower
OBJECT-TYPE
The lowest aggregated optical power of all the DWDM input channels in the OChGroup during the interval.
1.3.6.1.4.1.2636.3.73.1.1.5.3.1.4Integer32read-onlycurrent
jnxoptIfOChGroupSinkIntervalHighAggregatedInputPower
OBJECT-TYPE
The highest aggregated optical power of all the DWDM input channels in the OChGroup during the interval.
1.3.6.1.4.1.2636.3.73.1.1.5.3.1.5Integer32read-onlycurrent
jnxoptIfOChGroupSinkIntervalLastOutputPower
OBJECT-TYPE
The last optical power monitored at the output in the OChGroup during the interval.
1.3.6.1.4.1.2636.3.73.1.1.5.3.1.6Integer32read-onlycurrent
jnxoptIfOChGroupSinkIntervalLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output in the OChGroup during the interval.
1.3.6.1.4.1.2636.3.73.1.1.5.3.1.7Integer32read-onlycurrent
jnxoptIfOChGroupSinkIntervalHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output in the OChGroup during the interval.
1.3.6.1.4.1.2636.3.73.1.1.5.3.1.8Integer32read-onlycurrent
jnxoptIfOChGroupSinkCurDayTable
OBJECT-TYPE
A table of OChGroup sink performance monitoring information for the current 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.5.4not-accessiblecurrent
jnxoptIfOChGroupSinkCurDayEntry
OBJECT-TYPE
A conceptual row that contains OChGroup sink performance monitoring information of an interface for the current 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.5.4.1not-accessiblecurrent
jnxoptIfOChGroupSinkCurDaySuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.4.1.2636.3.73.1.1.5.4.1.1TruthValueread-onlycurrent
jnxoptIfOChGroupSinkCurDayLowAggregatedInputPower
OBJECT-TYPE
The lowest aggregated optical power of all the DWDM input channels in the OChGroup during the current 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.5.4.1.2Integer32read-onlycurrent
jnxoptIfOChGroupSinkCurDayHighAggregatedInputPower
OBJECT-TYPE
The highest aggregated optical power of all the DWDM input channels in the OChGroup during the current 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.5.4.1.3Integer32read-onlycurrent
jnxoptIfOChGroupSinkCurDayLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output in the OChGroup during the current 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.5.4.1.4Integer32read-onlycurrent
jnxoptIfOChGroupSinkCurDayHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output in the OChGroup during the current 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.5.4.1.5Integer32read-onlycurrent
jnxoptIfOChGroupSinkPrevDayTable
OBJECT-TYPE
A table of OChGroup sink performance monitoring information for the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.5.5not-accessiblecurrent
jnxoptIfOChGroupSinkPrevDayEntry
OBJECT-TYPE
A conceptual row that contains OChGroup sink performance monitoring information of an interface for the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.5.5.1not-accessiblecurrent
jnxoptIfOChGroupSinkPrevDaySuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.4.1.2636.3.73.1.1.5.5.1.1TruthValueread-onlycurrent
jnxoptIfOChGroupSinkPrevDayLastAggregatedInputPower
OBJECT-TYPE
The last aggregated optical power of all the DWDM input channels in the OChGroup during the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.5.5.1.2Integer32read-onlycurrent
jnxoptIfOChGroupSinkPrevDayLowAggregatedInputPower
OBJECT-TYPE
The lowest aggregated optical power of all the DWDM input channels in the OChGroup during the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.5.5.1.3Integer32read-onlycurrent
jnxoptIfOChGroupSinkPrevDayHighAggregatedInputPower
OBJECT-TYPE
The highest aggregated optical power of all the DWDM input channels in the OChGroup during the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.5.5.1.4Integer32read-onlycurrent
jnxoptIfOChGroupSinkPrevDayLastOutputPower
OBJECT-TYPE
The last optical power monitored at the output in the OChGroup during the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.5.5.1.5Integer32read-onlycurrent
jnxoptIfOChGroupSinkPrevDayLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output in the OChGroup during the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.5.5.1.6Integer32read-onlycurrent
jnxoptIfOChGroupSinkPrevDayHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output in the OChGroup during the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.5.5.1.7Integer32read-onlycurrent
jnxoptIfOChGroupSrcCurrentTable
OBJECT-TYPE
A table of OChGroup source performance monitoring information for the current 15-minute interval.
1.3.6.1.4.1.2636.3.73.1.1.5.6not-accessiblecurrent
jnxoptIfOChGroupSrcCurrentEntry
OBJECT-TYPE
A conceptual row that contains OChGroup source performance monitoring information of an interface for the current 15-minute interval.
1.3.6.1.4.1.2636.3.73.1.1.5.6.1not-accessiblecurrent
jnxoptIfOChGroupSrcCurrentSuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.4.1.2636.3.73.1.1.5.6.1.1TruthValueread-onlycurrent
jnxoptIfOChGroupSrcCurrentOutputPower
OBJECT-TYPE
The optical power monitored at the output.
1.3.6.1.4.1.2636.3.73.1.1.5.6.1.2Integer32read-onlycurrent
jnxoptIfOChGroupSrcCurrentLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output during the current 15-minute interval.
1.3.6.1.4.1.2636.3.73.1.1.5.6.1.3Integer32read-onlycurrent
jnxoptIfOChGroupSrcCurrentHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output during the current 15-minute interval.
1.3.6.1.4.1.2636.3.73.1.1.5.6.1.4Integer32read-onlycurrent
jnxoptIfOChGroupSrcCurrentLowerOutputPowerThreshold
OBJECT-TYPE
The lower limit threshold on output power. If jnxoptIfOChGroupSrcCurrentOutputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.4.1.2636.3.73.1.1.5.6.1.5Integer32read-writecurrent
jnxoptIfOChGroupSrcCurrentUpperOutputPowerThreshold
OBJECT-TYPE
The upper limit threshold on output power. If jnxoptIfOChGroupSrcCurrentOutputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.4.1.2636.3.73.1.1.5.6.1.6Integer32read-writecurrent
jnxoptIfOChGroupSrcCurrentAggregatedInputPower
OBJECT-TYPE
The aggregated optical power monitored at the input.
1.3.6.1.4.1.2636.3.73.1.1.5.6.1.7Integer32read-onlycurrent
jnxoptIfOChGroupSrcCurrentLowAggregatedInputPower
OBJECT-TYPE
The lowest aggregated optical power monitored at the input during the current 15-minute interval.
1.3.6.1.4.1.2636.3.73.1.1.5.6.1.8Integer32read-onlycurrent
jnxoptIfOChGroupSrcCurrentHighAggregatedInputPower
OBJECT-TYPE
The highest aggregated optical power monitored at the input during the current 15-minute interval.
1.3.6.1.4.1.2636.3.73.1.1.5.6.1.9Integer32read-onlycurrent
jnxoptIfOChGroupSrcCurrentLowerInputPowerThreshold
OBJECT-TYPE
The lower limit threshold on input power. If jnxoptIfOChGroupSrcCurrentAggregatedInputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.4.1.2636.3.73.1.1.5.6.1.10Integer32read-writecurrent
jnxoptIfOChGroupSrcCurrentUpperInputPowerThreshold
OBJECT-TYPE
The upper limit threshold on input power. If jnxoptIfOChGroupSrcCurrentAggregatedInputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.4.1.2636.3.73.1.1.5.6.1.11Integer32read-writecurrent
jnxoptIfOChGroupSrcIntervalTable
OBJECT-TYPE
A table of historical OChGroup source performance monitoring information.
1.3.6.1.4.1.2636.3.73.1.1.5.7not-accessiblecurrent
jnxoptIfOChGroupSrcIntervalEntry
OBJECT-TYPE
A conceptual row that contains OChGroup source performance monitoring information of an interface during a particular historical interval.
1.3.6.1.4.1.2636.3.73.1.1.5.7.1not-accessiblecurrent
jnxoptIfOChGroupSrcIntervalNumber
OBJECT-TYPE
Uniquely identifies the interval.
1.3.6.1.4.1.2636.3.73.1.1.5.7.1.1JnxoptIfIntervalNumbernot-accessiblecurrent
jnxoptIfOChGroupSrcIntervalSuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.4.1.2636.3.73.1.1.5.7.1.2TruthValueread-onlycurrent
jnxoptIfOChGroupSrcIntervalLastOutputPower
OBJECT-TYPE
The last optical power monitored at the output during the interval.
1.3.6.1.4.1.2636.3.73.1.1.5.7.1.3Integer32read-onlycurrent
jnxoptIfOChGroupSrcIntervalLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output during the interval.
1.3.6.1.4.1.2636.3.73.1.1.5.7.1.4Integer32read-onlycurrent
jnxoptIfOChGroupSrcIntervalHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output during the interval.
1.3.6.1.4.1.2636.3.73.1.1.5.7.1.5Integer32read-onlycurrent
jnxoptIfOChGroupSrcIntervalLastAggregatedInputPower
OBJECT-TYPE
The last aggregated optical power monitored at the input during the interval.
1.3.6.1.4.1.2636.3.73.1.1.5.7.1.6Integer32read-onlycurrent
jnxoptIfOChGroupSrcIntervalLowAggregatedInputPower
OBJECT-TYPE
The lowest aggregated optical power monitored at the input during the interval.
1.3.6.1.4.1.2636.3.73.1.1.5.7.1.7Integer32read-onlycurrent
jnxoptIfOChGroupSrcIntervalHighAggregatedInputPower
OBJECT-TYPE
The highest aggregated optical power monitored at the input during the interval.
1.3.6.1.4.1.2636.3.73.1.1.5.7.1.8Integer32read-onlycurrent
jnxoptIfOChGroupSrcCurDayTable
OBJECT-TYPE
A table of OChGroup source performance monitoring information for the current 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.5.8not-accessiblecurrent
jnxoptIfOChGroupSrcCurDayEntry
OBJECT-TYPE
A conceptual row that contains OChGroup source performance monitoring information of an interface for the current 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.5.8.1not-accessiblecurrent
jnxoptIfOChGroupSrcCurDaySuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.4.1.2636.3.73.1.1.5.8.1.1TruthValueread-onlycurrent
jnxoptIfOChGroupSrcCurDayLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output during the current 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.5.8.1.2Integer32read-onlycurrent
jnxoptIfOChGroupSrcCurDayHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output during the current 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.5.8.1.3Integer32read-onlycurrent
jnxoptIfOChGroupSrcCurDayLowAggregatedInputPower
OBJECT-TYPE
The lowest aggregated optical power monitored at the input during the current 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.5.8.1.4Integer32read-onlycurrent
jnxoptIfOChGroupSrcCurDayHighAggregatedInputPower
OBJECT-TYPE
The highest aggregated optical power monitored at the input during the current 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.5.8.1.5Integer32read-onlycurrent
jnxoptIfOChGroupSrcPrevDayTable
OBJECT-TYPE
A table of OChGroup source performance monitoring information for the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.5.9not-accessiblecurrent
jnxoptIfOChGroupSrcPrevDayEntry
OBJECT-TYPE
A conceptual row that contains OChGroup source performance monitoring information of an interface for the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.5.9.1not-accessiblecurrent
jnxoptIfOChGroupSrcPrevDaySuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.4.1.2636.3.73.1.1.5.9.1.1TruthValueread-onlycurrent
jnxoptIfOChGroupSrcPrevDayLastOutputPower
OBJECT-TYPE
The last optical power monitored at the output during the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.5.9.1.2Integer32read-onlycurrent
jnxoptIfOChGroupSrcPrevDayLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output during the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.5.9.1.3Integer32read-onlycurrent
jnxoptIfOChGroupSrcPrevDayHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output during the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.5.9.1.4Integer32read-onlycurrent
jnxoptIfOChGroupSrcPrevDayLastAggregatedInputPower
OBJECT-TYPE
The last aggregated optical power monitored at the input during the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.5.9.1.5Integer32read-onlycurrent
jnxoptIfOChGroupSrcPrevDayLowAggregatedInputPower
OBJECT-TYPE
The lowest aggregated optical power monitored at the input during the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.5.9.1.6Integer32read-onlycurrent
jnxoptIfOChGroupSrcPrevDayHighAggregatedInputPower
OBJECT-TYPE
The highest aggregated optical power monitored at the input during the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.5.9.1.7Integer32read-onlycurrent
jnxoptIfOCh
OBJECT-IDENTITY
1.3.6.1.4.1.2636.3.73.1.1.6
jnxoptIfOChConfigTable
OBJECT-TYPE
A table of OCh configuration information.
1.3.6.1.4.1.2636.3.73.1.1.6.1not-accessiblecurrent
jnxoptIfOChConfigEntry
OBJECT-TYPE
A conceptual row that contains OCh configuration information of an interface.
1.3.6.1.4.1.2636.3.73.1.1.6.1.1not-accessiblecurrent
jnxoptIfOChDirectionality
OBJECT-TYPE
Indicates the directionality of the entity.
1.3.6.1.4.1.2636.3.73.1.1.6.1.1.1JnxoptIfDirectionalityread-onlycurrent
jnxoptIfOChCurrentStatus
OBJECT-TYPE
Indicates the defect condition of the entity, if any. This object is applicable when jnxoptIfOChDirectionality has the value sink(1) or bidirectional(3). In full-capability systems the bit position los(1) is not used. In reduced-capability systems or at IrDI interfaces only the bit positions los(1) and ssfP(3) are used.
1.3.6.1.4.1.2636.3.73.1.1.6.1.1.2Bits {losP(0), los(1), oci(2), ssfP(3), ssfO(4), ssf(5)}read-onlycurrent
jnxoptIfOChSinkCurrentTable
OBJECT-TYPE
A table of OCh sink performance monitoring information for the current 15-minute interval.
1.3.6.1.4.1.2636.3.73.1.1.6.2not-accessiblecurrent
jnxoptIfOChSinkCurrentEntry
OBJECT-TYPE
A conceptual row that contains OCh sink performance monitoring information for an interface for the current 15-minute interval.
1.3.6.1.4.1.2636.3.73.1.1.6.2.1not-accessiblecurrent
jnxoptIfOChSinkCurrentSuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.4.1.2636.3.73.1.1.6.2.1.1TruthValueread-onlycurrent
jnxoptIfOChSinkCurrentInputPower
OBJECT-TYPE
The optical power monitored at the input.
1.3.6.1.4.1.2636.3.73.1.1.6.2.1.2Integer32read-onlycurrent
jnxoptIfOChSinkCurrentLowInputPower
OBJECT-TYPE
The lowest optical power monitored at the input during the current 15-minute interval.
1.3.6.1.4.1.2636.3.73.1.1.6.2.1.3Integer32read-onlycurrent
jnxoptIfOChSinkCurrentHighInputPower
OBJECT-TYPE
The highest optical power monitored at the input during the current 15-minute interval.
1.3.6.1.4.1.2636.3.73.1.1.6.2.1.4Integer32read-onlycurrent
jnxoptIfOChSinkCurrentLowerInputPowerThreshold
OBJECT-TYPE
The lower limit threshold on input power. If jnxoptIfOChSinkCurrentInputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.4.1.2636.3.73.1.1.6.2.1.5Integer32read-writecurrent
jnxoptIfOChSinkCurrentUpperInputPowerThreshold
OBJECT-TYPE
The upper limit threshold on input power. If jnxoptIfOChSinkCurrentInputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.4.1.2636.3.73.1.1.6.2.1.6Integer32read-writecurrent
jnxoptIfOChSinkIntervalTable
OBJECT-TYPE
A table of historical OCh sink performance monitoring information.
1.3.6.1.4.1.2636.3.73.1.1.6.3not-accessiblecurrent
jnxoptIfOChSinkIntervalEntry
OBJECT-TYPE
A conceptual row that contains OCh sink performance monitoring information of an interface during a particular historical interval.
1.3.6.1.4.1.2636.3.73.1.1.6.3.1not-accessiblecurrent
jnxoptIfOChSinkIntervalNumber
OBJECT-TYPE
Uniquely identifies the interval.
1.3.6.1.4.1.2636.3.73.1.1.6.3.1.1JnxoptIfIntervalNumbernot-accessiblecurrent
jnxoptIfOChSinkIntervalSuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.4.1.2636.3.73.1.1.6.3.1.2TruthValueread-onlycurrent
jnxoptIfOChSinkIntervalLastInputPower
OBJECT-TYPE
The last optical power monitored at the input during the interval.
1.3.6.1.4.1.2636.3.73.1.1.6.3.1.3Integer32read-onlycurrent
jnxoptIfOChSinkIntervalLowInputPower
OBJECT-TYPE
The lowest optical power monitored at the input during the interval.
1.3.6.1.4.1.2636.3.73.1.1.6.3.1.4Integer32read-onlycurrent
jnxoptIfOChSinkIntervalHighInputPower
OBJECT-TYPE
The highest optical power monitored at the input during the interval.
1.3.6.1.4.1.2636.3.73.1.1.6.3.1.5Integer32read-onlycurrent
jnxoptIfOChSinkCurDayTable
OBJECT-TYPE
A table of OCh sink performance monitoring information for the current 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.6.4not-accessiblecurrent
jnxoptIfOChSinkCurDayEntry
OBJECT-TYPE
A conceptual row that contains OCh sink performance monitoring information of an interface for the current 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.6.4.1not-accessiblecurrent
jnxoptIfOChSinkCurDaySuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.4.1.2636.3.73.1.1.6.4.1.1TruthValueread-onlycurrent
jnxoptIfOChSinkCurDayLowInputPower
OBJECT-TYPE
The lowest optical power monitored at the input during the current 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.6.4.1.2Integer32read-onlycurrent
jnxoptIfOChSinkCurDayHighInputPower
OBJECT-TYPE
The highest optical power monitored at the input during the current 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.6.4.1.3Integer32read-onlycurrent
jnxoptIfOChSinkPrevDayTable
OBJECT-TYPE
A table of OCh sink performance monitoring information for the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.6.5not-accessiblecurrent
jnxoptIfOChSinkPrevDayEntry
OBJECT-TYPE
A conceptual row that contains OCh sink performance monitoring information of an interface for the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.6.5.1not-accessiblecurrent
jnxoptIfOChSinkPrevDaySuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.4.1.2636.3.73.1.1.6.5.1.1TruthValueread-onlycurrent
jnxoptIfOChSinkPrevDayLastInputPower
OBJECT-TYPE
The last optical power monitored at the input during the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.6.5.1.2Integer32read-onlycurrent
jnxoptIfOChSinkPrevDayLowInputPower
OBJECT-TYPE
The lowest optical power monitored at the input during the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.6.5.1.3Integer32read-onlycurrent
jnxoptIfOChSinkPrevDayHighInputPower
OBJECT-TYPE
The highest optical power monitored at the input during the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.6.5.1.4Integer32read-onlycurrent
jnxoptIfOChSrcCurrentTable
OBJECT-TYPE
A table of OCh source performance monitoring information for the current 15-minute interval.
1.3.6.1.4.1.2636.3.73.1.1.6.6not-accessiblecurrent
jnxoptIfOChSrcCurrentEntry
OBJECT-TYPE
A conceptual row that contains OCh source performance monitoring information of an interface for the current 15-minute interval.
1.3.6.1.4.1.2636.3.73.1.1.6.6.1not-accessiblecurrent
jnxoptIfOChSrcCurrentSuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.4.1.2636.3.73.1.1.6.6.1.1TruthValueread-onlycurrent
jnxoptIfOChSrcCurrentOutputPower
OBJECT-TYPE
The optical power monitored at the output.
1.3.6.1.4.1.2636.3.73.1.1.6.6.1.2Integer32read-onlycurrent
jnxoptIfOChSrcCurrentLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output during the current 15-minute interval.
1.3.6.1.4.1.2636.3.73.1.1.6.6.1.3Integer32read-onlycurrent
jnxoptIfOChSrcCurrentHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output during the current 15-minute interval.
1.3.6.1.4.1.2636.3.73.1.1.6.6.1.4Integer32read-onlycurrent
jnxoptIfOChSrcCurrentLowerOutputPowerThreshold
OBJECT-TYPE
The lower limit threshold on output power. If jnxoptIfOChSrcCurrentOutputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.4.1.2636.3.73.1.1.6.6.1.5Integer32read-writecurrent
jnxoptIfOChSrcCurrentUpperOutputPowerThreshold
OBJECT-TYPE
The upper limit threshold on output power. If jnxoptIfOChSrcCurrentOutputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.4.1.2636.3.73.1.1.6.6.1.6Integer32read-writecurrent
jnxoptIfOChSrcIntervalTable
OBJECT-TYPE
A table of historical OCh source performance monitoring information.
1.3.6.1.4.1.2636.3.73.1.1.6.7not-accessiblecurrent
jnxoptIfOChSrcIntervalEntry
OBJECT-TYPE
A conceptual row that contains OCh source performance monitoring information of an interface during a particular historical interval.
1.3.6.1.4.1.2636.3.73.1.1.6.7.1not-accessiblecurrent
jnxoptIfOChSrcIntervalNumber
OBJECT-TYPE
Uniquely identifies the interval.
1.3.6.1.4.1.2636.3.73.1.1.6.7.1.1JnxoptIfIntervalNumbernot-accessiblecurrent
jnxoptIfOChSrcIntervalSuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.4.1.2636.3.73.1.1.6.7.1.2TruthValueread-onlycurrent
jnxoptIfOChSrcIntervalLastOutputPower
OBJECT-TYPE
The last optical power monitored at the output during the interval.
1.3.6.1.4.1.2636.3.73.1.1.6.7.1.3Integer32read-onlycurrent
jnxoptIfOChSrcIntervalLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output during the interval.
1.3.6.1.4.1.2636.3.73.1.1.6.7.1.4Integer32read-onlycurrent
jnxoptIfOChSrcIntervalHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output during the interval.
1.3.6.1.4.1.2636.3.73.1.1.6.7.1.5Integer32read-onlycurrent
jnxoptIfOChSrcCurDayTable
OBJECT-TYPE
A table of OCh source performance monitoring information for the current 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.6.8not-accessiblecurrent
jnxoptIfOChSrcCurDayEntry
OBJECT-TYPE
A conceptual row that contains OCh source performance monitoring information of an interface for the current 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.6.8.1not-accessiblecurrent
jnxoptIfOChSrcCurDaySuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.4.1.2636.3.73.1.1.6.8.1.1TruthValueread-onlycurrent
jnxoptIfOChSrcCurDayLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output during the current 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.6.8.1.2Integer32read-onlycurrent
jnxoptIfOChSrcCurDayHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output during the current 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.6.8.1.3Integer32read-onlycurrent
jnxoptIfOChSrcPrevDayTable
OBJECT-TYPE
A table of OCh source performance monitoring information for the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.6.9not-accessiblecurrent
jnxoptIfOChSrcPrevDayEntry
OBJECT-TYPE
A conceptual row that contains OCh source performance monitoring information of an interface for the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.6.9.1not-accessiblecurrent
jnxoptIfOChSrcPrevDaySuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.4.1.2636.3.73.1.1.6.9.1.1TruthValueread-onlycurrent
jnxoptIfOChSrcPrevDayLastOutputPower
OBJECT-TYPE
The last optical power monitored at the output during the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.6.9.1.2Integer32read-onlycurrent
jnxoptIfOChSrcPrevDayLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output during the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.6.9.1.3Integer32read-onlycurrent
jnxoptIfOChSrcPrevDayHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output during the previous 24-hour interval.
1.3.6.1.4.1.2636.3.73.1.1.6.9.1.4Integer32read-onlycurrent
jnxoptIfOTUk
OBJECT-IDENTITY
1.3.6.1.4.1.2636.3.73.1.1.7
jnxoptIfOTUkConfigTable
OBJECT-TYPE
A table of OTUk configuration information.
1.3.6.1.4.1.2636.3.73.1.1.7.1not-accessiblecurrent
jnxoptIfOTUkConfigEntry
OBJECT-TYPE
A conceptual row that contains OTUk configuration information of an interface.
1.3.6.1.4.1.2636.3.73.1.1.7.1.1not-accessiblecurrent
jnxoptIfOTUkDirectionality
OBJECT-TYPE
Indicates the directionality of the entity.
1.3.6.1.4.1.2636.3.73.1.1.7.1.1.1JnxoptIfDirectionalityread-onlycurrent
jnxoptIfOTUkBitRateK
OBJECT-TYPE
Indicates the bit rate of the entity.
1.3.6.1.4.1.2636.3.73.1.1.7.1.1.2JnxoptIfBitRateKread-onlycurrent
jnxoptIfOTUkTraceIdentifierTransmitted
OBJECT-TYPE
The trace identifier transmitted. This object is applicable when jnxoptIfOTUkDirectionality has the value source(2) or bidirectional(3). It must not be instantiated in rows where jnxoptIfOTUkDirectionality has the value sink(1). If no value is ever set by a management entity for this object, system-specific default value will be used. Any implementation that instantiates this object must document the system-specific default value or how it is derived.
1.3.6.1.4.1.2636.3.73.1.1.7.1.1.3JnxoptIfTxTIread-writecurrent
jnxoptIfOTUkDAPIExpected
OBJECT-TYPE
The DAPI expected by the receiver. This object is only applicable to the sink function, i.e., only when jnxoptIfOTUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where jnxoptIfOTUkDirectionality has the value source(2). This object has no effect when jnxoptIfOTUkTIMDetMode has the value off(1).
1.3.6.1.4.1.2636.3.73.1.1.7.1.1.4JnxoptIfExDAPIread-writecurrent
jnxoptIfOTUkSAPIExpected
OBJECT-TYPE
The SAPI expected by the receiver. This object is only applicable to the sink function, i.e., only when jnxoptIfOTUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where jnxoptIfOTUkDirectionality has the value source(2). This object has no effect when jnxoptIfOTUkTIMDetMode has the value off(1).
1.3.6.1.4.1.2636.3.73.1.1.7.1.1.5JnxoptIfExSAPIread-writecurrent
jnxoptIfOTUkTraceIdentifierAccepted
OBJECT-TYPE
The actual trace identifier accepted. This object is only applicable to the sink function, i.e., only when jnxoptIfOTUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where jnxoptIfOTUkDirectionality has the value source(2). The value of this object is unspecified when jnxoptIfOTUkCurrentStatus indicates a near-end defect (i.e., ssf(3), lof(4), ais(5), lom(6)) that prevents extraction of the trace message.
1.3.6.1.4.1.2636.3.73.1.1.7.1.1.6JnxoptIfAcTIread-onlycurrent
jnxoptIfOTUkTIMDetMode
OBJECT-TYPE
Indicates the mode of the Trace Identifier Mismatch (TIM) Detection function. This object is only applicable to the sink function, i.e., only when jnxoptIfOTUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where jnxoptIfOTUkDirectionality has the value source(2). The default value of this object is off(1).
1.3.6.1.4.1.2636.3.73.1.1.7.1.1.7JnxoptIfTIMDetModeread-writecurrent
jnxoptIfOTUkTIMActEnabled
OBJECT-TYPE
Indicates whether the Trace Identifier Mismatch (TIM) Consequent Action function is enabled. This object is only applicable to the sink function, i.e., only when jnxoptIfOTUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where jnxoptIfOTUkDirectionality has the value source(2). This object has no effect when jnxoptIfOTUkTIMDetMode has the value off(1). The default value of this object is false(2).
1.3.6.1.4.1.2636.3.73.1.1.7.1.1.8TruthValueread-writecurrent
jnxoptIfOTUkDEGThr
OBJECT-TYPE
Indicates the threshold level for declaring a performance monitoring (PM) Second to be bad. A PM Second is declared bad if the percentage of detected errored blocks in that second is greater than or equal to jnxoptIfOTUkDEGThr. This object is only applicable to the sink function, i.e., only when jnxoptIfOTUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where jnxoptIfOTUkDirectionality has the value source(2). The default value of this object is Severely Errored Second (SES) Estimator (See ITU-T G.7710).
1.3.6.1.4.1.2636.3.73.1.1.7.1.1.9JnxoptIfDEGThrread-writecurrent
jnxoptIfOTUkDEGM
OBJECT-TYPE
Indicates the threshold level for declaring a Degraded Signal defect (dDEG). A dDEG shall be declared if jnxoptIfOTUkDEGM consecutive bad PM Seconds are detected. This object is only applicable to the sink function, i.e., only when jnxoptIfOTUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where jnxoptIfOTUkDirectionality has the value source(2). The default value of this object is 7 (See ITU-T G.7710).
1.3.6.1.4.1.2636.3.73.1.1.7.1.1.10JnxoptIfDEGMread-writecurrent
jnxoptIfOTUkSinkAdaptActive
OBJECT-TYPE
Indicates whether the sink adaptation function is activated or not. This object is only applicable to the sink function, i.e., only when jnxoptIfOTUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where jnxoptIfOTUkDirectionality has the value source(2). The default value of this object is false(2).
1.3.6.1.4.1.2636.3.73.1.1.7.1.1.11TruthValueread-writecurrent
jnxoptIfOTUkSourceAdaptActive
OBJECT-TYPE
Indicates whether the source adaptation function is activated or not. This object is only applicable to the source function, i.e., only when jnxoptIfOTUkDirectionality has the value source(2) or bidirectional(3). It must not be instantiated in rows where jnxoptIfOTUkDirectionality has the value sink(1). The default value of this object is false(2).
1.3.6.1.4.1.2636.3.73.1.1.7.1.1.12TruthValueread-writecurrent
jnxoptIfOTUkSinkFECEnabled
OBJECT-TYPE
If Forward Error Correction (FEC) is supported, this object indicates whether FEC at the OTUk sink adaptation function is enabled or not. This object is only applicable to the sink function, i.e., only when jnxoptIfOTUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where jnxoptIfOTUkDirectionality has the value source(2). The default value of this object is true(1).
1.3.6.1.4.1.2636.3.73.1.1.7.1.1.13TruthValueread-writecurrent
jnxoptIfOTUkCurrentStatus
OBJECT-TYPE
Indicates the defect condition of the entity, if any. This object is only applicable to the sink function, i.e., only when jnxoptIfOTUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where jnxoptIfOTUkDirectionality has the value source(2).
1.3.6.1.4.1.2636.3.73.1.1.7.1.1.14Bits {tim(0), deg(1), bdi(2), ssf(3), lof(4), ais(5), lom(6)}read-onlycurrent
jnxoptIfGCC0ConfigTable
OBJECT-TYPE
A table of GCC0 configuration information.
1.3.6.1.4.1.2636.3.73.1.1.7.2not-accessiblecurrent
jnxoptIfGCC0ConfigEntry
OBJECT-TYPE
A conceptual row that contains GCC0 configuration information of an interface. Each instance must correspond to an instance of jnxoptIfOTUkConfigEntry. Separate source and/or sink instances may exist for a given ifIndex value, or a single bidirectional instance may exist, but a bidirectional instance may not coexist with a source or sink instance. Instances of this conceptual row persist across agent restarts.
1.3.6.1.4.1.2636.3.73.1.1.7.2.1not-accessiblecurrent
jnxoptIfGCC0Directionality
OBJECT-TYPE
Indicates the directionality of the entity. The values source(2) and bidirectional(3) are not allowed if the corresponding instance of jnxoptIfOTUkDirectionality has the value sink(1). The values sink(1) and bidirectional(3) are not allowed if the corresponding instance of jnxoptIfOTUkDirectionality has the value source(2).
1.3.6.1.4.1.2636.3.73.1.1.7.2.1.1JnxoptIfDirectionalitynot-accessiblecurrent
jnxoptIfGCC0Application
OBJECT-TYPE
Indicates the application transported by the GCC0 entity. Example applications are ECC, User data channel. The value of this object may not be changed when jnxoptIfGCC0RowStatus has the value active(1).
1.3.6.1.4.1.2636.3.73.1.1.7.2.1.2SnmpAdminStringread-createcurrent
jnxoptIfGCC0RowStatus
OBJECT-TYPE
This columnar object is used for creating and deleting a conceptual row of the jnxoptIfGCC0 config table. It is used to model the addGCC0Access and removeGCC0Access operations of an OTUk_TTP for GCC0 access control as defined in G.874.1. Setting RowStatus to createAndGo or createAndWait implies addGCC0Access. Setting RowStatus to destroy implies removeGCC0Access.
1.3.6.1.4.1.2636.3.73.1.1.7.2.1.3RowStatusread-createcurrent
jnxoptIfODUk
OBJECT-IDENTITY
1.3.6.1.4.1.2636.3.73.1.1.8
jnxoptIfODUkConfigTable
OBJECT-TYPE
A table of ODUk configuration information.
1.3.6.1.4.1.2636.3.73.1.1.8.1not-accessiblecurrent
jnxoptIfODUkConfigEntry
OBJECT-TYPE
A conceptual row that contains ODUk configuration information of an interface.
1.3.6.1.4.1.2636.3.73.1.1.8.1.1not-accessiblecurrent
jnxoptIfODUkDirectionality
OBJECT-TYPE
Indicates the directionality of the entity.
1.3.6.1.4.1.2636.3.73.1.1.8.1.1.1JnxoptIfDirectionalityread-onlycurrent
jnxoptIfODUkBitRateK
OBJECT-TYPE
Indicates the bit rate of the entity.
1.3.6.1.4.1.2636.3.73.1.1.8.1.1.2JnxoptIfBitRateKread-onlycurrent
jnxoptIfODUkTcmFieldsInUse
OBJECT-TYPE
Indicates the TCM field(s) that are currently in use. The positions of the bits correspond to the TCM fields. A bit that is set to 1 means that the corresponding TCM field is used. This object will be updated when rows are created in or deleted from the jnxoptIfODUkTConfigTable, or the jnxoptIfODUkTNimConfigTable.
1.3.6.1.4.1.2636.3.73.1.1.8.1.1.3Bits {tcmField1(0), tcmField2(1), tcmField3(2), tcmField4(3), tcmField5(4), tcmField6(5)}read-onlycurrent
jnxoptIfODUkPositionSeqCurrentSize
OBJECT-TYPE
This variable indicates the current size of the position sequence (i.e., number of TCM function and/or GCC12 access that have been created in the ODUk interface). When the value of this variable is greater than zero, it means that one or more TCM function and/or GCC12 access have been created in the ODUk interface. In this case, there will be as many rows in the jnxoptIfODUkPositionSeqTable as the value of jnxoptIfODUkPositionSeqCurrentSize corresponding to this ODUk interface, one row for each TCM function or GCC12 access. The position of the TCM function and/or GCC12 access within the sequence is indicated by the jnxoptIfODUkPositionSeqPosition variable in jnxoptIfODUkPositionSeqTable. The jnxoptIfODUkPositionSeqTable also provides pointers to the corresponding TCM function (jnxoptIfODUkT) and GCC12 access (jnxoptIfGCC12) entities.
1.3.6.1.4.1.2636.3.73.1.1.8.1.1.4Unsigned32read-onlycurrent
jnxoptIfODUkTtpPresent
OBJECT-TYPE
This object has the value true(1) if the ifEntry under which it is instantiated contains an ODUk Trail Termination Point, i.e., is the endpoint of an ODUk path. In that case there will be a corresponding row in the ODUk TTP config table and it will not be possible to create corresponding rows in the ODUk NIM config table. This object has the value false(2) if the ifEntry under which it is instantiated contains an intermediate ODUk Connection Termination Point. In that case there is no corresponding row in the ODUk TTP config table, but it will be possible to create corresponding rows in the ODUk NIM config table. This object also affects the allowable options in rows created in the GCC12 config table and in the ODUkT config table, as specified in the DESCRIPTION clauses of the columns in those tables.
1.3.6.1.4.1.2636.3.73.1.1.8.1.1.5TruthValueread-onlycurrent
jnxoptIfODUkTtpConfigTable
OBJECT-TYPE
A table of ODUk TTP configuration information.
1.3.6.1.4.1.2636.3.73.1.1.8.2not-accessiblecurrent
jnxoptIfODUkTtpConfigEntry
OBJECT-TYPE
A conceptual row that contains ODUk TTP configuration information of an interface.
1.3.6.1.4.1.2636.3.73.1.1.8.2.1not-accessiblecurrent
jnxoptIfODUkTtpTraceIdentifierTransmitted
OBJECT-TYPE
The trace identifier transmitted. This object is applicable when jnxoptIfODUkDirectionality has the value source(2) or bidirectional(3). It must not be instantiated in rows where jnxoptIfODUkDirectionality has the value sink(1). If no value is ever set by a management entity for this object, system-specific default value will be used. Any implementation that instantiates this object must document the system-specific default value or how it is derived.
1.3.6.1.4.1.2636.3.73.1.1.8.2.1.1JnxoptIfTxTIread-writecurrent
jnxoptIfODUkTtpDAPIExpected
OBJECT-TYPE
The DAPI expected by the receiver. This object is only applicable to the sink function, i.e., only when jnxoptIfODUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where jnxoptIfODUkDirectionality has the value source(2). This object has no effect when jnxoptIfODUkTtpTIMDetMode has the value off(1).
1.3.6.1.4.1.2636.3.73.1.1.8.2.1.2JnxoptIfExDAPIread-writecurrent
jnxoptIfODUkTtpSAPIExpected
OBJECT-TYPE
The SAPI expected by the receiver. This object is only applicable to the sink function, i.e., only when jnxoptIfODUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where jnxoptIfODUkDirectionality has the value source(2). This object has no effect when jnxoptIfODUkTtpTIMDetMode has the value off(1).
1.3.6.1.4.1.2636.3.73.1.1.8.2.1.3JnxoptIfExSAPIread-writecurrent
jnxoptIfODUkTtpTraceIdentifierAccepted
OBJECT-TYPE
The actual trace identifier accepted. This object is only applicable to the sink function, i.e., only when jnxoptIfODUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where jnxoptIfODUkDirectionality has the value source(2). The value of this object is unspecified when jnxoptIfODUkTtpCurrentStatus indicates a near-end defect (i.e., oci(0), lck(1), ssf(5)) that prevents extraction of the trace message.
1.3.6.1.4.1.2636.3.73.1.1.8.2.1.4JnxoptIfAcTIread-onlycurrent
jnxoptIfODUkTtpTIMDetMode
OBJECT-TYPE
Indicates the mode of the Trace Identifier Mismatch (TIM) Detection function. This object is only applicable to the sink function, i.e., only when jnxoptIfODUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where jnxoptIfODUkDirectionality has the value source(2). The default value of this object is off(1).
1.3.6.1.4.1.2636.3.73.1.1.8.2.1.5JnxoptIfTIMDetModeread-writecurrent
jnxoptIfODUkTtpTIMActEnabled
OBJECT-TYPE
Indicates whether the Trace Identifier Mismatch (TIM) Consequent Action function is enabled. This object is only applicable to the sink function, i.e., only when jnxoptIfODUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where jnxoptIfODUkDirectionality has the value source(2). This object has no effect when jnxoptIfODUkTtpTIMDetMode has the value off(1). The default value of this object is false(2).
1.3.6.1.4.1.2636.3.73.1.1.8.2.1.6TruthValueread-writecurrent
jnxoptIfODUkTtpDEGThr
OBJECT-TYPE
Indicates the threshold level for declaring a performance monitoring (PM) Second to be bad. A PM Second is declared bad if the percentage of detected errored blocks in that second is greater than or equal to jnxoptIfODUkDEGThr. This object is only applicable to the sink function, i.e., only when jnxoptIfODUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where jnxoptIfODUkDirectionality has the value source(2). The default value of this object is Severely Errored Second (SES) Estimator (See ITU-T G.7710).
1.3.6.1.4.1.2636.3.73.1.1.8.2.1.7JnxoptIfDEGThrread-writecurrent
jnxoptIfODUkTtpDEGM
OBJECT-TYPE
Indicates the threshold level for declaring a Degraded Signal defect (dDEG). A dDEG shall be declared if jnxoptIfODUkDEGM consecutive bad PM Seconds are detected. This object is only applicable to the sink function, i.e., only when jnxoptIfODUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where jnxoptIfODUkDirectionality has the value source(2). The default value of this object is 7 (See ITU-T G.7710).
1.3.6.1.4.1.2636.3.73.1.1.8.2.1.8JnxoptIfDEGMread-writecurrent
jnxoptIfODUkTtpCurrentStatus
OBJECT-TYPE
Indicates the defect condition of the entity, if any. This object is only applicable to the sink function, i.e., only when jnxoptIfODUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where jnxoptIfODUkDirectionality has the value source(2).
1.3.6.1.4.1.2636.3.73.1.1.8.2.1.9Bits {oci(0), lck(1), tim(2), deg(3), bdi(4), ssf(5)}read-onlycurrent
jnxoptIfODUkPositionSeqTable
OBJECT-TYPE
A table of ODUk Position Sequence information.
1.3.6.1.4.1.2636.3.73.1.1.8.3not-accessiblecurrent
jnxoptIfODUkPositionSeqEntry
OBJECT-TYPE
A conceptual row that contains ODUk position sequence information of an ODUk interface. The ODUk interface is identified by the ifIndex. Associated with each ODUk interface there may be one of more conceptual rows in the jnxoptIfODUkPositionSeqTable. Each row represents a TCM or GCC12 access function within the associated ODUk interface. Rows of the jnxoptIfODUkPositionSeqTable table are created/deleted as the result of the creation/deletion of the jnxoptIfODUkT or jnxoptIfGCC12 entities.
1.3.6.1.4.1.2636.3.73.1.1.8.3.1not-accessiblecurrent
jnxoptIfODUkPositionSeqIndex
OBJECT-TYPE
This variable identifies a row in the jnxoptIfODUkPositionSeqTable Table. Each row of the jnxoptIfODUkPositionSeqTable Table represents a TCM or GCC12 access function within the associated ODUk interface.
1.3.6.1.4.1.2636.3.73.1.1.8.3.1.1Unsigned32 (1..4294967295)not-accessiblecurrent
jnxoptIfODUkPositionSeqPosition
OBJECT-TYPE
This variable indicates the position of the TCM or GCC12 access function within the sequence of TCMs & GCC12 access functions of the associated ODUk interface. The TCM or GCC12 presented by this row is referenced by the jnxoptIfODUkPositionSeqPointer variable.
1.3.6.1.4.1.2636.3.73.1.1.8.3.1.2Unsigned32read-onlycurrent
jnxoptIfODUkPositionSeqPointer
OBJECT-TYPE
This variable identifies the TCM or GCC12 access function by pointing to the corresponding jnxoptIfODUkT or jnxoptIfGCC12 entity.
1.3.6.1.4.1.2636.3.73.1.1.8.3.1.3RowPointerread-onlycurrent
jnxoptIfODUkNimConfigTable
OBJECT-TYPE
A table of ODUkNim configuration information.
1.3.6.1.4.1.2636.3.73.1.1.8.4not-accessiblecurrent
jnxoptIfODUkNimConfigEntry
OBJECT-TYPE
A conceptual row that contains ODUkNim configuration information of an interface. Each instance must correspond to an instance of jnxoptIfODUkConfigEntry for which jnxoptIfODUkTtpPresent has the value false(2). Instances of this conceptual row persist across agent restarts, and read-create columns other than the status column may be modified while the row is active.
1.3.6.1.4.1.2636.3.73.1.1.8.4.1not-accessiblecurrent
jnxoptIfODUkNimDirectionality
OBJECT-TYPE
Specifies the monitor point for the ODUk Path non-intrusive monitoring function. The value source(2) is not allowed if the corresponding instance of jnxoptIfODUkDirectionality has the value sink(1), and the value sink(1) is not allowed if the corresponding instance of jnxoptIfODUkDirectionality has the value source(2). Either the value sink(1) or source(2) is allowed if the corresponding instance of jnxoptIfODUkDirectionality has the value bidirectional(3). The value sink(1) means monitoring at the sink direction path signal of the ODUk CTP. The value source(2) means monitoring at the source direction path signal of the ODUk CTP. Monitoring the source direction of an ODUk CTP is necessary in those cases where the ODUk CTP is at an SNCP (Subnetwork Connection Protection) end (e.g., see Figure I.1.2/G.874.1). If one would like to get the performance of the protected connection, one cannot use the NIM function at both ODUk CTP sinks (before the matrix), instead one should monitor the signal at the source ODUk CTP after the matrix.
1.3.6.1.4.1.2636.3.73.1.1.8.4.1.1JnxoptIfSinkOrSourcenot-accessiblecurrent
jnxoptIfODUkNimDAPIExpected
OBJECT-TYPE
The DAPI expected by the receiver. This object has no effect if jnxoptIfODUkNimTIMDetMode has the value off(1) or sapi(3).
1.3.6.1.4.1.2636.3.73.1.1.8.4.1.2JnxoptIfExDAPIread-createcurrent
jnxoptIfODUkNimSAPIExpected
OBJECT-TYPE
The SAPI expected by the receiver. This object has no effect if jnxoptIfODUkNimTIMDetMode has the value off(1) or dapi(2).
1.3.6.1.4.1.2636.3.73.1.1.8.4.1.3JnxoptIfExSAPIread-createcurrent
jnxoptIfODUkNimTraceIdentifierAccepted
OBJECT-TYPE
The actual trace identifier accepted. The value of this object is unspecified if jnxoptIfODUkNimCurrentStatus has any of the bit positions oci(0), lck(1), or ssf(5) set or if jnxoptIfODUkNimRowStatus has any value other than active(1).
1.3.6.1.4.1.2636.3.73.1.1.8.4.1.4JnxoptIfAcTIread-onlycurrent
jnxoptIfODUkNimTIMDetMode
OBJECT-TYPE
Indicates the mode of the Trace Identifier Mismatch (TIM) Detection function.
1.3.6.1.4.1.2636.3.73.1.1.8.4.1.5JnxoptIfTIMDetModeread-createcurrent
jnxoptIfODUkNimTIMActEnabled
OBJECT-TYPE
Indicates whether the Trace Identifier Mismatch (TIM) Consequent Action function is enabled.
1.3.6.1.4.1.2636.3.73.1.1.8.4.1.6TruthValueread-createcurrent
jnxoptIfODUkNimDEGThr
OBJECT-TYPE
Indicates the threshold level for declaring a performance monitoring (PM) Second to be bad. A PM Second is declared bad if the percentage of detected errored blocks in that second is greater than or equal to jnxoptIfODUkNimDEGThr.
1.3.6.1.4.1.2636.3.73.1.1.8.4.1.7JnxoptIfDEGThrread-createcurrent
jnxoptIfODUkNimDEGM
OBJECT-TYPE
Indicates the threshold level for declaring a Degraded Signal defect (dDEG). A dDEG shall be declared if jnxoptIfODUkNimDEGM consecutive bad PM Seconds are detected.
1.3.6.1.4.1.2636.3.73.1.1.8.4.1.8JnxoptIfDEGMread-createcurrent
jnxoptIfODUkNimCurrentStatus
OBJECT-TYPE
Indicates the defect condition of the entity, if any. The value of this object is unspecified if jnxoptIfODUkNimRowStatus has any value other than active(1).
1.3.6.1.4.1.2636.3.73.1.1.8.4.1.9Bits {oci(0), lck(1), tim(2), deg(3), bdi(4), ssf(5)}read-onlycurrent
jnxoptIfODUkNimRowStatus
OBJECT-TYPE
This columnar object is used for creating and deleting a conceptual row of the jnxoptIfODUkNim config table. It is used to model the activateNim and deactivateNim operations of an OTUk_CTP for non-intrusive monitoring control as defined in G.874.1. Setting RowStatus to createAndGo or createAndWait implies activateNim. Setting RowStatus to destroy implies deactivateNim.
1.3.6.1.4.1.2636.3.73.1.1.8.4.1.10RowStatusread-createcurrent
jnxoptIfGCC12ConfigTable
OBJECT-TYPE
A table of GCC12 configuration information. The GCC function processes the GCC overhead bytes passing through them but leave the remainder of the ODUk overhead and payload data alone.
1.3.6.1.4.1.2636.3.73.1.1.8.5not-accessiblecurrent
jnxoptIfGCC12ConfigEntry
OBJECT-TYPE
A conceptual row that contains GCC12 configuration information of an interface. Each instance must correspond to an instance of jnxoptIfODUkConfigEntry. Separate instances providing GCC1-only access and GCC2-only access may exist for a given ifIndex value, or a single instance providing GCC1 + GCC2 may exist, but a GCC1 + GCC2 instance may not coexist with a GCC1-only or GCC2-only instance. Instances of this conceptual row persist across agent restarts.
1.3.6.1.4.1.2636.3.73.1.1.8.5.1not-accessiblecurrent
jnxoptIfGCC12Codirectional
OBJECT-TYPE
Indicates the directionality of the GCC12 termination with respect to the associated ODUk CTP. The value true(1) means that the sink part of the GCC12 extracts COMMS data from the signal at the input to the ODUk CTP sink and the source part of the GCC12 inserts COMMS data into the signal at the output of the ODUk CTP source. The value false(2) means that the sink part of the GCC12 extracts COMMS data from the signal at the output of the ODUk CTP source and the source part of the GCC12 inserts COMMS data into the signal at the input of the ODUk CTP sink. This attribute may assume either value when the corresponding instance of jnxoptIfODUkTtpPresent has the value false(2). When the value of the corresponding instance of jnxoptIfODUkTtpPresent is true(1) then the only value allowed for this attribute is true(1).
1.3.6.1.4.1.2636.3.73.1.1.8.5.1.1TruthValuenot-accessiblecurrent
jnxoptIfGCC12GCCAccess
OBJECT-TYPE
Indicates the GCC access represented by the entity.
1.3.6.1.4.1.2636.3.73.1.1.8.5.1.2INTEGER {gcc1(1), gcc2(2), gcc1and2(3)}not-accessiblecurrent
jnxoptIfGCC12GCCPassThrough
OBJECT-TYPE
Controls whether the selected GCC overhead bytes are passed through or modified. The value true(1) means that the selected GCC overhead bytes are passed through unmodified from the ODUk CTP input to the ODUk CTP output. The value false(2) means that the selected GCC overhead bytes are set to zero at the ODUk CTP output after the extraction of the COMMS data. This object has no effect if the corresponding instance of jnxoptIfODUkTtpPresent has the value true(1). The value of this object may not be changed when jnxoptIfGCC12RowStatus has the value active(1).
1.3.6.1.4.1.2636.3.73.1.1.8.5.1.3TruthValueread-createcurrent
jnxoptIfGCC12Application
OBJECT-TYPE
Indicates the application transported by the GCC12 entity. Example applications are ECC, User data channel. The value of this object may not be changed when jnxoptIfGCC12RowStatus has the value active(1).
1.3.6.1.4.1.2636.3.73.1.1.8.5.1.4SnmpAdminStringread-createcurrent
jnxoptIfGCC12RowStatus
OBJECT-TYPE
This columnar object is used for creating and deleting a conceptual row of the jnxoptIfGCC12 config table. It is used to model the addGCC12Access and removeGCC12Access operations of an ODUk_CTP or ODUk_TTP for GCC12 access control as defined in G.874.1. Setting RowStatus to createAndGo or createAndWait implies addGCC12Access. Setting RowStatus to destroy implies removeGCC12Access. Successful addition/removal of the GCC12 access function will result in updating the jnxoptIfODUkPositionSeqCurrentSize variable and the jnxoptIfODUkPositionSeqTable table of the associated ODUk entry in the jnxoptIfODUkConfigTable.
1.3.6.1.4.1.2636.3.73.1.1.8.5.1.5RowStatusread-createcurrent
jnxoptIfODUkT
OBJECT-IDENTITY
1.3.6.1.4.1.2636.3.73.1.1.9
jnxoptIfODUkTConfigTable
OBJECT-TYPE
A table of ODUkT configuration information.
1.3.6.1.4.1.2636.3.73.1.1.9.1not-accessiblecurrent
jnxoptIfODUkTConfigEntry
OBJECT-TYPE
A conceptual row that contains ODUkT configuration information of an interface. Each instance must correspond to an instance of jnxoptIfODUkConfigEntry. Rows in this table are mutually exclusive with rows in the ODUkT NIM config table -- in other words, this row object may not be instantiated for a given pair of ifIndex and TCM field values if a corresponding instance of jnxoptIfODUkTNimConfigEntry already exists. Instances of this conceptual row persist across agent restarts. Except where noted otherwise, read-create columns other than the status column may be modified while the row is active.
1.3.6.1.4.1.2636.3.73.1.1.9.1.1not-accessiblecurrent
jnxoptIfODUkTTcmField
OBJECT-TYPE
Indicates the tandem connection monitoring field of the ODUk OH. Valid values are integers from 1 to 6.
1.3.6.1.4.1.2636.3.73.1.1.9.1.1.1Unsigned32 (1..6)not-accessiblecurrent
jnxoptIfODUkTCodirectional
OBJECT-TYPE
Indicates the directionality of the ODUkT termination point with respect to the associated ODUk CTP. The value true(1) means that the sink part of the ODUkT TP extracts TCM data from the signal at the input to the ODUk CTP sink and the source part of the ODUkT TP inserts TCM data into the signal at the output of the ODUk CTP source. The value false(2) means that the sink part of the ODUkT TP extracts TCM data from the signal at the output of the ODUk CTP source and the source part of the ODUkT TP inserts TCM data into the signal at the input of the ODUk CTP sink. This attribute may assume either value when the corresponding instance of jnxoptIfODUkTtpPresent has the value false(2). When the value of the corresponding instance of jnxoptIfODUkTtpPresent is true(1) then the only value allowed for this attribute is true(1).
1.3.6.1.4.1.2636.3.73.1.1.9.1.1.2TruthValuenot-accessiblecurrent
jnxoptIfODUkTTraceIdentifierTransmitted
OBJECT-TYPE
The trace identifier transmitted. This object is applicable only to the following three cases. (i) jnxoptIfODUkDirectionality has the value bidirectional(3), or (ii) jnxoptIfODUkDirectionality has the value sink(1) and jnxoptIfODUkTCodirectional has the value false(2), or (iii) jnxoptIfODUkDirectionality has the value source(3) and jnxoptIfODUkTCodirectional has the value true(1). It must not be instantiated in rows for all other cases.
1.3.6.1.4.1.2636.3.73.1.1.9.1.1.3JnxoptIfTxTIread-createcurrent
jnxoptIfODUkTDAPIExpected
OBJECT-TYPE
The DAPI expected by the receiver. This object is applicable only to the following three cases. (i) jnxoptIfODUkDirectionality has the value bidirectional(3), or (ii) jnxoptIfODUkDirectionality has the value sink(1) and jnxoptIfODUkTCodirectional has the value true(1), or (iii) jnxoptIfODUkDirectionality has the value source(3) and jnxoptIfODUkTCodirectional has the value false(2). It must not be instantiated in rows for all other cases. This object has no effect when jnxoptIfODUkTTIMDetMode has the value off(1).
1.3.6.1.4.1.2636.3.73.1.1.9.1.1.4JnxoptIfExDAPIread-createcurrent
jnxoptIfODUkTSAPIExpected
OBJECT-TYPE
The SAPI expected by the receiver. This object is applicable only to the following three cases. (i) jnxoptIfODUkDirectionality has the value bidirectional(3), or (ii) jnxoptIfODUkDirectionality has the value sink(1) and jnxoptIfODUkTCodirectional has the value true(1), or (iii) jnxoptIfODUkDirectionality has the value source(3) and jnxoptIfODUkTCodirectional has the value false(2). It must not be instantiated in rows for all other cases. This object has no effect when jnxoptIfODUkTTIMDetMode has the value off(1).
1.3.6.1.4.1.2636.3.73.1.1.9.1.1.5JnxoptIfExSAPIread-createcurrent
jnxoptIfODUkTTraceIdentifierAccepted
OBJECT-TYPE
The actual trace identifier accepted. This object is applicable only to the following three cases. (i) jnxoptIfODUkDirectionality has the value bidirectional(3), or (ii) jnxoptIfODUkDirectionality has the value sink(1) and jnxoptIfODUkTCodirectional has the value true(1), or (iii) jnxoptIfODUkDirectionality has the value source(3) and jnxoptIfODUkTCodirectional has the value false(2). It must not be instantiated in rows for all other cases. The value of this object is unspecified when jnxoptIfODUkTCurrentStatus indicates a near-end defect (i.e., oci(0), lck(1), ssf(5)) that prevents extraction of the trace message.
1.3.6.1.4.1.2636.3.73.1.1.9.1.1.6JnxoptIfAcTIread-onlycurrent
jnxoptIfODUkTTIMDetMode
OBJECT-TYPE
Indicates the mode of the Trace Identifier Mismatch (TIM) Detection function. This object is applicable only to the following three cases. (i) jnxoptIfODUkDirectionality has the value bidirectional(3), or (ii) jnxoptIfODUkDirectionality has the value sink(1) and jnxoptIfODUkTCodirectional has the value true(1), or (iii) jnxoptIfODUkDirectionality has the value source(3) and jnxoptIfODUkTCodirectional has the value false(2). It must not be instantiated in rows for all other cases. The default value of this object is off(1).
1.3.6.1.4.1.2636.3.73.1.1.9.1.1.7JnxoptIfTIMDetModeread-createcurrent
jnxoptIfODUkTTIMActEnabled
OBJECT-TYPE
Indicates whether the Trace Identifier Mismatch (TIM) Consequent Action function is enabled. This object is applicable only to the following three cases. (i) jnxoptIfODUkDirectionality has the value bidirectional(3), or (ii) jnxoptIfODUkDirectionality has the value sink(1) and jnxoptIfODUkTCodirectional has the value true(1), or (iii) jnxoptIfODUkDirectionality has the value source(3) and jnxoptIfODUkTCodirectional has the value false(2). It must not be instantiated in rows for all other cases. This object has no effect when jnxoptIfODUkTTIMDetMode has the value off(1). The default value of this object is false(2).
1.3.6.1.4.1.2636.3.73.1.1.9.1.1.8TruthValueread-createcurrent
jnxoptIfODUkTDEGThr
OBJECT-TYPE
Indicates the threshold level for declaring a performance monitoring (PM) Second to be bad. A PM Second is declared bad if the percentage of detected errored blocks in that second is greater than or equal to jnxoptIfODUkTDEGThr. This object is applicable only to the following three cases. (i) jnxoptIfODUkDirectionality has the value bidirectional(3), or (ii) jnxoptIfODUkDirectionality has the value sink(1) and jnxoptIfODUkTCodirectional has the value true(1), or (iii) jnxoptIfODUkDirectionality has the value source(3) and jnxoptIfODUkTCodirectional has the value false(2). It must not be instantiated in rows for all other cases. The default value of this object is Severely Errored Second (SES) Estimator (See ITU-T G.7710).
1.3.6.1.4.1.2636.3.73.1.1.9.1.1.9JnxoptIfDEGThrread-createcurrent
jnxoptIfODUkTDEGM
OBJECT-TYPE
Indicates the threshold level for declaring a Degraded Signal defect (dDEG). A dDEG shall be declared if jnxoptIfODUkTDEGM consecutive bad PM Seconds are detected. This object is applicable only to the following three cases. (i) jnxoptIfODUkDirectionality has the value bidirectional(3), or (ii) jnxoptIfODUkDirectionality has the value sink(1) and jnxoptIfODUkTCodirectional has the value true(1), or (iii) jnxoptIfODUkDirectionality has the value source(3) and jnxoptIfODUkTCodirectional has the value false(2). It must not be instantiated in rows for all other cases. The default value of this object is 7 (See ITU-T G.7710).
1.3.6.1.4.1.2636.3.73.1.1.9.1.1.10JnxoptIfDEGMread-createcurrent
jnxoptIfODUkTSinkMode
OBJECT-TYPE
This variable specifies the TCM mode at the entity. The value operational(1) means that TCM Overhead (TCMOH) processes (see ITU-T G.798) shall be performed and consequent actions for AIS, Trail Signal Fail (TSF), Trail Signal Degraded (TSD) shall be initiated in case of defects. The value monitor(2) means that TCMOH processes shall be performed but consequent actions for AIS, Trail Server Failure (TSF), Trail Server Degraded (TSD) shall _not_ be initiated in case of defects. This object is applicable only when the value of jnxoptIfODUkTtpPresent is false(2) and also either one of the following three cases holds: (i) jnxoptIfODUkDirectionality has the value bidirectional(3), or (ii) jnxoptIfODUkDirectionality has the value sink(1) and jnxoptIfODUkTCodirectional has the value true(1), or (iii) jnxoptIfODUkDirectionality has the value source(3) and jnxoptIfODUkTCodirectional has the value false(2). It must not be instantiated in rows for all other cases.
1.3.6.1.4.1.2636.3.73.1.1.9.1.1.11INTEGER {operational(1), monitor(2)}read-createcurrent
jnxoptIfODUkTSinkLockSignalAdminState
OBJECT-TYPE
Provides the capability to provision the LOCK signal, which is one of the ODUk maintenance signals, at the ODUKT sink. When a Tandem Connection endpoint is set to admin state locked, it inserts the ODUk-LCK signal in the sink direction. This object is applicable only when the value of jnxoptIfODUkTtpPresent is false(2) and also either one of the following three cases holds: (i) jnxoptIfODUkDirectionality has the value bidirectional(3), or (ii) jnxoptIfODUkDirectionality has the value sink(1) and jnxoptIfODUkTCodirectional has the value true(1), or (iii) jnxoptIfODUkDirectionality has the value source(3) and jnxoptIfODUkTCodirectional has the value false(2). It must not be instantiated in rows for all other cases.
1.3.6.1.4.1.2636.3.73.1.1.9.1.1.12INTEGER {locked(1), normal(2)}read-createcurrent
jnxoptIfODUkTSourceLockSignalAdminState
OBJECT-TYPE
Provides the capability to provision the LOCK signal, which is one of the ODUk maintenance signals, at the source. When a Tandem Connection endpoint is set to admin state locked, it inserts the ODUk-LCK signal in the source direction. This object is applicable only when either one of the following three cases holds: (i) jnxoptIfODUkDirectionality has the value bidirectional(3), or (ii) jnxoptIfODUkDirectionality has the value sink(1) and jnxoptIfODUkTCodirectional has the value false(2), or (iii) jnxoptIfODUkDirectionality has the value source(3) and jnxoptIfODUkTCodirectional has the value true(1). It must not be instantiated in rows for all other cases.
1.3.6.1.4.1.2636.3.73.1.1.9.1.1.13INTEGER {locked(1), normal(2)}read-createcurrent
jnxoptIfODUkTCurrentStatus
OBJECT-TYPE
Indicates the defect condition of the entity, if any. This object is applicable only when either one of the following three cases holds: (i) jnxoptIfODUkDirectionality has the value bidirectional(3), or (ii) jnxoptIfODUkDirectionality has the value sink(1) and jnxoptIfODUkTCodirectional has the value true(1), or (iii) jnxoptIfODUkDirectionality has the value source(3) and jnxoptIfODUkTCodirectional has the value false(2). It must not be instantiated in rows for all other cases.
1.3.6.1.4.1.2636.3.73.1.1.9.1.1.14Bits {oci(0), lck(1), tim(2), deg(3), bdi(4), ssf(5)}read-onlycurrent
jnxoptIfODUkTRowStatus
OBJECT-TYPE
This columnar object is used for creating and deleting a conceptual row of the jnxoptIfODUkT config table. It is used to model the addTCM and removeTCM operations of an ODUk_CTP or ODUk_TTP for Tandem connection monitoring as defined in ITU-T G.874.1. Setting RowStatus to createAndGo or createAndWait implies addTCM. Setting RowStatus to destroy implies removeTCM. Successful addition/removal of TCM will result in updating the jnxoptIfODUkTcmFieldsInUse and jnxoptIfODUkPositionSeqCurrentSize variables and the jnxoptIfODUkPositionSeqTable table of the associated ODUk entry in the jnxoptIfODUkConfigTable.
1.3.6.1.4.1.2636.3.73.1.1.9.1.1.15RowStatusread-createcurrent
jnxoptIfODUkTNimConfigTable
OBJECT-TYPE
A table of ODUkTNim configuration information.
1.3.6.1.4.1.2636.3.73.1.1.9.2not-accessiblecurrent
jnxoptIfODUkTNimConfigEntry
OBJECT-TYPE
A conceptual row that contains ODUkTNim configuration information of an interface. Each instance must correspond to an instance of jnxoptIfODUkConfigEntry. Rows in this table are mutually exclusive with rows in the ODUkT config table -- in other words, this row object may not be instantiated for a given pair of ifIndex and TCM field values if a corresponding instance of jnxoptIfODUkTConfigEntry already exists. Instances of this conceptual row persist across agent restarts, and read-create columns other than the status column may be modified while the row is active.
1.3.6.1.4.1.2636.3.73.1.1.9.2.1not-accessiblecurrent
jnxoptIfODUkTNimTcmField
OBJECT-TYPE
Indicates the tandem connection monitoring field of the ODUk OH on which non-intrusive monitoring is performed. Valid values are integers from 1 to 6.
1.3.6.1.4.1.2636.3.73.1.1.9.2.1.1Unsigned32 (1..6)not-accessiblecurrent
jnxoptIfODUkTNimDirectionality
OBJECT-TYPE
Specifies the monitor point for the ODUk TCM non-intrusive monitoring function. The value source(2) is not allowed if the corresponding instance of jnxoptIfODUkDirectionality has the value sink(1), and the value sink(1) is not allowed if the corresponding instance of jnxoptIfODUkDirectionality has the value source(2). Either the value sink(1) or source(2) is allowed if the corresponding instance of jnxoptIfODUkDirectionality has the value bidirectional(3). The value sink(1) means monitoring at the sink direction TCM signal of the ODUk CTP. The value source(2) means monitoring at the source direction path signal of the ODUk CTP.
1.3.6.1.4.1.2636.3.73.1.1.9.2.1.2JnxoptIfSinkOrSourcenot-accessiblecurrent
jnxoptIfODUkTNimDAPIExpected
OBJECT-TYPE
The DAPI expected by the receiver. This object has no effect if jnxoptIfODUkTNimTIMDetMode has the value off(1) or sapi(3).
1.3.6.1.4.1.2636.3.73.1.1.9.2.1.3JnxoptIfExDAPIread-createcurrent
jnxoptIfODUkTNimSAPIExpected
OBJECT-TYPE
The SAPI expected by the receiver. This object has no effect if jnxoptIfODUkTNimTIMDetMode has the value off(1) or dapi(2).
1.3.6.1.4.1.2636.3.73.1.1.9.2.1.4JnxoptIfExSAPIread-createcurrent
jnxoptIfODUkTNimTraceIdentifierAccepted
OBJECT-TYPE
The actual trace identifier accepted. The value of this object is unspecified if jnxoptIfODUkTNimCurrentStatus has any of the bit positions oci(0), lck(1), or ssf(5) set or if jnxoptIfODUkTNimRowStatus has any value other than active(1).
1.3.6.1.4.1.2636.3.73.1.1.9.2.1.5JnxoptIfAcTIread-onlycurrent
jnxoptIfODUkTNimTIMDetMode
OBJECT-TYPE
Indicates the mode of the Trace Identifier Mismatch (TIM) Detection function.
1.3.6.1.4.1.2636.3.73.1.1.9.2.1.6JnxoptIfTIMDetModeread-createcurrent
jnxoptIfODUkTNimTIMActEnabled
OBJECT-TYPE
Indicates whether the Trace Identifier Mismatch (TIM) Consequent Action function is enabled.
1.3.6.1.4.1.2636.3.73.1.1.9.2.1.7TruthValueread-createcurrent
jnxoptIfODUkTNimDEGThr
OBJECT-TYPE
Indicates the threshold level for declaring a performance monitoring (PM) Second to be bad. A PM Second is declared bad if the percentage of detected errored blocks in that second is greater than or equal to jnxoptIfODUkTNimDEGThr.
1.3.6.1.4.1.2636.3.73.1.1.9.2.1.8JnxoptIfDEGThrread-createcurrent
jnxoptIfODUkTNimDEGM
OBJECT-TYPE
Indicates the threshold level for declaring a Degraded Signal defect (dDEG). A dDEG shall be declared if jnxoptIfODUkTNimDEGM consecutive bad PM Seconds are detected.
1.3.6.1.4.1.2636.3.73.1.1.9.2.1.9JnxoptIfDEGMread-createcurrent
jnxoptIfODUkTNimCurrentStatus
OBJECT-TYPE
Indicates the defect condition of the entity, if any. The value of this object is unspecified if jnxoptIfODUkTNimRowStatus has any value other than active(1).
1.3.6.1.4.1.2636.3.73.1.1.9.2.1.10Bits {oci(0), lck(1), tim(2), deg(3), bdi(4), ssf(5)}read-onlycurrent
jnxoptIfODUkTNimRowStatus
OBJECT-TYPE
This columnar object is used for creating and deleting a conceptual row of the jnxoptIfODUkTNim config table. It is used to model the addTCM and removeTCM operations of an ODUk_CTP or ODUk_TTP for non-intrusive Tandem connection monitoring as defined in ITU-T G.874.1. Setting RowStatus to createAndGo or createAndWait implies addTCM. Setting RowStatus to destroy implies removeTCM. Successful addition/removal of Nim TCM will result in updating the jnxoptIfODUkPositionSeqCurrentSize variable and the jnxoptIfODUkPositionSeqTable table of the associated ODUk entry in the jnxoptIfODUkConfigTable.
1.3.6.1.4.1.2636.3.73.1.1.9.2.1.11RowStatusread-createcurrent
jnxoptIfConfs
OBJECT-IDENTITY
1.3.6.1.4.1.2636.3.73.1.2
jnxoptIfGroups
OBJECT-IDENTITY
1.3.6.1.4.1.2636.3.73.1.2.1
jnxoptIfCompl
OBJECT-IDENTITY
1.3.6.1.4.1.2636.3.73.1.2.2

Conformance

NameOIDStatus
jnxoptIfOTMnGroup
OBJECT-GROUP
A collection of OTMn structure information objects.
1.3.6.1.4.1.2636.3.73.1.2.1.1current
jnxoptIfPerfMonGroup
OBJECT-GROUP
A collection of performance monitoring interval objects.
1.3.6.1.4.1.2636.3.73.1.2.1.2current
jnxoptIfOTSnCommonGroup
OBJECT-GROUP
A collection of configuration objects applicable to all OTSn interfaces.
1.3.6.1.4.1.2636.3.73.1.2.1.3current
jnxoptIfOTSnSourceGroupFull
OBJECT-GROUP
A collection of configuration objects applicable to full-functionality/IaDI OTSn interfaces that support source functions.
1.3.6.1.4.1.2636.3.73.1.2.1.4current
jnxoptIfOTSnAPRStatusGroup
OBJECT-GROUP
A collection of objects applicable to OTSn interfaces that support Automatic Power Reduction functions.
1.3.6.1.4.1.2636.3.73.1.2.1.5current
jnxoptIfOTSnAPRControlGroup
OBJECT-GROUP
A collection of objects applicable to OTSn interfaces that provide Automatic Power Reduction control functions.
1.3.6.1.4.1.2636.3.73.1.2.1.6current
jnxoptIfOTSnSinkGroupBasic
OBJECT-GROUP
A collection of configuration objects applicable to all OTSn interfaces that support sink functions.
1.3.6.1.4.1.2636.3.73.1.2.1.7current
jnxoptIfOTSnSinkGroupFull
OBJECT-GROUP
A collection of configuration objects applicable to full-functionality/IaDI OTSn interfaces that support sink functions.
1.3.6.1.4.1.2636.3.73.1.2.1.8current
jnxoptIfOTSnSinkPreOtnPMGroup
OBJECT-GROUP
A collection of pre-OTN performance monitoring objects applicable to OTSn interfaces that support sink functions.
1.3.6.1.4.1.2636.3.73.1.2.1.9current
jnxoptIfOTSnSinkPreOtnPMThresholdGroup
OBJECT-GROUP
A collection of pre-OTN performance monitoring threshold objects applicable to OTSn interfaces that support sink functions.
1.3.6.1.4.1.2636.3.73.1.2.1.10current
jnxoptIfOTSnSourcePreOtnPMGroup
OBJECT-GROUP
A collection of pre-OTN performance monitoring objects applicable to OTSn interfaces that support source functions.
1.3.6.1.4.1.2636.3.73.1.2.1.11current
jnxoptIfOTSnSourcePreOtnPMThresholdGroup
OBJECT-GROUP
A collection of pre-OTN performance monitoring threshold objects applicable to OTSn interfaces that support source functions.
1.3.6.1.4.1.2636.3.73.1.2.1.12current
jnxoptIfOMSnCommonGroup
OBJECT-GROUP
A collection of configuration objects applicable to all OMSn interfaces.
1.3.6.1.4.1.2636.3.73.1.2.1.13current
jnxoptIfOMSnSinkGroupBasic
OBJECT-GROUP
A collection of configuration objects applicable to all OMSn interfaces that support sink functions.
1.3.6.1.4.1.2636.3.73.1.2.1.14current
jnxoptIfOMSnSinkPreOtnPMGroup
OBJECT-GROUP
A collection of pre-OTN performance monitoring objects applicable to OMSn interfaces that support sink functions.
1.3.6.1.4.1.2636.3.73.1.2.1.15current
jnxoptIfOMSnSinkPreOtnPMThresholdGroup
OBJECT-GROUP
A collection of pre-OTN performance monitoring threshold objects applicable to OMSn interfaces that support sink functions.
1.3.6.1.4.1.2636.3.73.1.2.1.16current
jnxoptIfOMSnSourcePreOtnPMGroup
OBJECT-GROUP
A collection of pre-OTN performance monitoring objects applicable to OMSn interfaces that support source functions.
1.3.6.1.4.1.2636.3.73.1.2.1.17current
jnxoptIfOMSnSourcePreOtnPMThresholdGroup
OBJECT-GROUP
A collection of pre-OTN performance monitoring threshold objects applicable to OMSn interfaces that that support source functions.
1.3.6.1.4.1.2636.3.73.1.2.1.18current
jnxoptIfOChGroupCommonGroup
OBJECT-GROUP
A collection of configuration objects applicable to all OChGroup interfaces.
1.3.6.1.4.1.2636.3.73.1.2.1.19current
jnxoptIfOChGroupSinkPreOtnPMGroup
OBJECT-GROUP
A collection of pre-OTN performance monitoring objects applicable to OChGroup interfaces that support sink functions.
1.3.6.1.4.1.2636.3.73.1.2.1.20current
jnxoptIfOChGroupSinkPreOtnPMThresholdGroup
OBJECT-GROUP
A collection of pre-OTN performance monitoring threshold objects applicable to OChGroup interfaces that support sink functions.
1.3.6.1.4.1.2636.3.73.1.2.1.21current
jnxoptIfOChGroupSourcePreOtnPMGroup
OBJECT-GROUP
A collection of pre-OTN performance monitoring objects applicable to OChGroup interfaces that support source functions.
1.3.6.1.4.1.2636.3.73.1.2.1.22current
jnxoptIfOChGroupSourcePreOtnPMThresholdGroup
OBJECT-GROUP
A collection of pre-OTN performance monitoring threshold objects applicable to OChGroup interfaces that that support source functions.
1.3.6.1.4.1.2636.3.73.1.2.1.23current
jnxoptIfOChCommonGroup
OBJECT-GROUP
A collection of configuration objects applicable to all OCh interfaces.
1.3.6.1.4.1.2636.3.73.1.2.1.24current
jnxoptIfOChSinkGroupBasic
OBJECT-GROUP
A collection of configuration objects applicable to all OCh interfaces that support sink functions.
1.3.6.1.4.1.2636.3.73.1.2.1.25current
jnxoptIfOChSinkPreOtnPMGroup
OBJECT-GROUP
A collection of pre-OTN performance monitoring objects applicable to OCh interfaces that support sink functions.
1.3.6.1.4.1.2636.3.73.1.2.1.26current
jnxoptIfOChSinkPreOtnPMThresholdGroup
OBJECT-GROUP
A collection of pre-OTN performance monitoring threshold objects applicable to OCh interfaces that support sink functions.
1.3.6.1.4.1.2636.3.73.1.2.1.27current
jnxoptIfOChSourcePreOtnPMGroup
OBJECT-GROUP
A collection of pre-OTN performance monitoring objects applicable to OCh interfaces that support source functions.
1.3.6.1.4.1.2636.3.73.1.2.1.28current
jnxoptIfOChSourcePreOtnPMThresholdGroup
OBJECT-GROUP
A collection of pre-OTN performance monitoring threshold objects applicable to OCh interfaces that support source functions.
1.3.6.1.4.1.2636.3.73.1.2.1.29current
jnxoptIfOTUkCommonGroup
OBJECT-GROUP
A collection of configuration objects applicable to all OTUk interfaces.
1.3.6.1.4.1.2636.3.73.1.2.1.30current
jnxoptIfOTUkSourceGroup
OBJECT-GROUP
A collection of configuration objects applicable to OTUk interfaces that support source functions.
1.3.6.1.4.1.2636.3.73.1.2.1.31current
jnxoptIfOTUkSinkGroup
OBJECT-GROUP
A collection of configuration objects applicable to OTUk interfaces that support sink functions.
1.3.6.1.4.1.2636.3.73.1.2.1.32current
jnxoptIfGCC0Group
OBJECT-GROUP
A collection of GCC0 configuration objects.
1.3.6.1.4.1.2636.3.73.1.2.1.33current
jnxoptIfODUkGroup
OBJECT-GROUP
A collection of configuration objects applicable to all ODUk interfaces.
1.3.6.1.4.1.2636.3.73.1.2.1.34current
jnxoptIfODUkTtpSourceGroup
OBJECT-GROUP
A collection of configuration objects applicable to all interfaces that support ODUk trail termination source functions.
1.3.6.1.4.1.2636.3.73.1.2.1.35current
jnxoptIfODUkTtpSinkGroup
OBJECT-GROUP
A collection of ODUk configuration objects applicable to all interfaces that support ODUk trail termination sink functions.
1.3.6.1.4.1.2636.3.73.1.2.1.36current
jnxoptIfODUkNimGroup
OBJECT-GROUP
A collection of ODUk Nim configuration objects.
1.3.6.1.4.1.2636.3.73.1.2.1.37current
jnxoptIfGCC12Group
OBJECT-GROUP
A collection of GCC12 configuration objects.
1.3.6.1.4.1.2636.3.73.1.2.1.38current
jnxoptIfODUkTCommonGroup
OBJECT-GROUP
A collection of configuration objects applicable to all ODUkT instances.
1.3.6.1.4.1.2636.3.73.1.2.1.39current
jnxoptIfODUkTSourceGroup
OBJECT-GROUP
A collection of configuration objects applicable to all ODUkT instances that provide source functions.
1.3.6.1.4.1.2636.3.73.1.2.1.40current
jnxoptIfODUkTSinkGroup
OBJECT-GROUP
A collection of configuration objects applicable to all ODUkT instances that provide sink functions.
1.3.6.1.4.1.2636.3.73.1.2.1.41current
jnxoptIfODUkTSinkGroupCtp
OBJECT-GROUP
A collection of configuration objects applicable to ODUkT instances not colocated with an ODUk TTP that provide sink functions.
1.3.6.1.4.1.2636.3.73.1.2.1.42current
jnxoptIfODUkTNimGroup
OBJECT-GROUP
A collection of ODUkT Nim configuration objects.
1.3.6.1.4.1.2636.3.73.1.2.1.43current
jnxoptIfOtnConfigCompl
MODULE-COMPLIANCE
Implementation requirements for the OTN configuration functions defined in this MIB module.
1.3.6.1.4.1.2636.3.73.1.2.2.1current
jnxoptIfPreOtnPMCompl
MODULE-COMPLIANCE
Implementation requirements for Pre-OTN performance monitoring functions defined in this MIB module.
1.3.6.1.4.1.2636.3.73.1.2.2.2current