HUAWEI-ETHOAM-MIB

TEXTUAL-CONVENTION

Detect the mode type: Fast detect and standard detect

TEXTUAL-CONVENTION

Possible values returned in the egress action field

TEXTUAL-CONVENTION

An enumerated value, equal to the contents of the variable highestDefect (20.33.9 and Table 20-1), indicating the highest-priority defect that has been present since the MEP Fault Notification Generator State Machine was last in the FNG_RESET state, either: none(0) no defects since FNG_RESET defRDICCM(1) DefRDICCM defMACstatus(2) DefMACstatus defRemoteCCM(3) DefRemoteCCM defErrorCCM(4) DefErrorCCM defXconCCM(5) DefXconCCM The value 0 is used for no defects so that additional higher priority values can be added, if needed, at a later time, and so that these values correspond with those in Dot1agCfmLowestAlarmPri.

TEXTUAL-CONVENTION

Possible values returned in the ingress action field.

TEXTUAL-CONVENTION

Integer identifying the Maintenance Domain Level (MD Level). Higher numbers correspond to higher Maintenance Domains, those with the greatest physical reach, with the highest values for customers' CFM PDUs. Lower numbers correspond to lower Maintenance Domains, those with more limited physical reach, with the lowest values for CFM PDUs protecting single bridges or physical links.

TEXTUAL-CONVENTION

Indicates the possible values the Relay action field can take.

TEXTUAL-CONVENTION

24-bit Organizationally Unique Identifier. Information on OUIs can be found in IEEE 802-2001 [802-2001] Clause 9.

TEXTUAL-CONVENTION

The five values indicates: has not run/is running/the previous test terminates normally/the previous test terminates abnormally/the previous test is interrupted (through ctrl+c or mib)

TEXTUAL-CONVENTION

Transmission rate: 1Mbps and 5Mbps.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

This object indicates whether CFM is enabled globally. The value of this object can be: Enabled: indicates that CFM is enabled globally. Disabled: indicates that global CFM is disabled

OBJECT-TYPE

This object indicates the supported CFM version. The value of this object can be: draft: indicates IEEE 802.1ag Draft 7. standard: indicates IEEE Standard 802.1ag-2007.

OBJECT-IDENTITY

OBJECT-TYPE

The index to the Maintenance Domain table. hwDot1agCfmMdTableNextIndex needs to be inspected to find an available index for row-creation.

OBJECT-TYPE

This table is used to create a Maintenance Domain (MD). A Maintenance Domain is described in 802.1ag (3.22) as the network or the part of the network for which faults in connectivity are to be managed. The boundary of a Maintenance Domain is defined by a set of DSAPs, each of which can become a point of connectivity to a service instance.

OBJECT-TYPE

The Maintenance Domain table entry. This entry is not lost upon reboot. It is backed up by stable storage.

OBJECT-TYPE

This object indicates the index of the MD Table. hwDot1agCfmMdTableNextIndex needs to be inspected to find an available index for row-creation.

OBJECT-TYPE

This object indicates the format of the MD name. By default, the value is string.

OBJECT-TYPE

This object indicates the name of the MD. The type/format of this object is determined by the value of the hwDot1agCfmMdFormat object. Each Maintenance Domain has unique name amongst all those used or available to a service provider or operator. It facilitates easy identification of administrative responsibility for each Maintenance Domain.

OBJECT-TYPE

This object indicates the level of the MD. The value ranges from 0 to 7. The greater the value, the higher the preference. By default, the value is 0.

OBJECT-TYPE

This object indicates whether the management entity can create MIPs for the MD. The value of this object can be: defMHFnone: indicates that the MIPs are not automatically created. defMHFdefault: indicates that the management entity automatically creates MIPs based on certain rules. defMHFexplicit: indicates that the management entity automatically creates MIPs based on certain rules. By default, the value is defMHFnone.

OBJECT-TYPE

This object indicates what is to be included in the Sender ID TLV transmitted by MPs configured in the MD. The value of this object can be: sendIdNone: indicates that the Sender ID TLV is not to be sent. sendIdChassis: indicates that the Sender ID TLV to be sent contains the chassis ID information. sendIdManage: indicates that the Sender ID TLV to be sent contains management address information. sendIdChassisManage: indicates that the Sender ID TLV to be sent contains both chassis ID information and management address information. sendIdDefer: indicates that the contents of the Sender ID TLV to be sent are determined by the MD management entity. By default, the value is sendIdDefer.

OBJECT-TYPE

This object indicates the MD format name. The type/format of this object is determined by the value of the hwDot1agCfmMdFormatName object. Each Maintenance Domain has unique name amongst all those used or available to a service provider or operator. It facilitates easy identification of administrative responsibility for each Maintenance Domain.

OBJECT-TYPE

This object indicates the row status of this table. The writable columns in a row can not be changed if the row is active. All columns MUST have a valid value before a row can be activated.

OBJECT-IDENTITY

OBJECT-TYPE

Value to be used as the index of the MA table entries.

OBJECT-TYPE

This table is used to create a Maintenance Association (MA). Each row in the table represents an MA. An MA is a set of MEPs, each configured with a single service instance.

OBJECT-TYPE

The MA table entry.

OBJECT-TYPE

This object indicates the index of the MA table.

OBJECT-TYPE

This object indicates the name of the MA. This name MUST be unique within a maintenance domain.

OBJECT-TYPE

This object indicates what is associated with the MA. The value of this object can be: mapVlan: indicates that a VLAN is associated with the current MA. mapVsi: indicates that a VSI is associated with the current MA. mapL2vc: indicates that an L2VC is associated with the current MA. unbind: indicates that the MA is not associated with any service instance. mapCcc: indicates that a CCC is associated with the current MA. By default, the value is unbind.

OBJECT-TYPE

This object indicates the ID of the VLAN associated with the MA.

OBJECT-TYPE

This object indicates the name of the VSI associated with the MA.

OBJECT-TYPE

This object indicates the ID of the L2VC associated with the MA.

OBJECT-TYPE

This object indicates the encapsulation type of the L2VC associated with the MA. The value of this object can be: invalid: indicates that no display shows that the L2VC is associated with the current MA. l2vcRaw: indicates that the VLAN tag is not encapsulated into the packet. l2vcTagged: indicates that the VLAN tag is encapsulated into the packet. By default, the value is invalid.

OBJECT-TYPE

This object indicates the priority of the 802.1ag packet sent in the MA. The value ranges from 0 to 7. The greater the value is, the higher the priority is. By default, the value is 7.

OBJECT-TYPE

This object indicates the interval for an MEP in the MA to send or probe CCMs. The value of this object can be: 3.3 milliseconds 10 milliseconds 20 milliseconds 30 milliseconds 50 milliseconds 100 milliseconds 1 second 10 seconds 1 minute 10 minutes By default, the value is 1 second.

OBJECT-TYPE

This object indicates the time period after which RMEP configurations are to be activated. The value ranges from 0 to 600 in seconds. By default, the value is 0.

OBJECT-TYPE

This object indicates the delay for the RMEP to send trap messages. The value must be an integer multiple of 500, for example, 500, 1000, or 1500. The value ranges from 0 to 30000 in milliseconds. By default, the value is 2500.

OBJECT-TYPE

This object indicates the delay for the RMEP to send alarm clearance messages after the fault is rectified. The value must be an integer multiple of 500, for example, 500, 1000, or 1500. The value ranges from 0 to 30000 in milliseconds. By default, the value is 10000.

OBJECT-TYPE

This object indicates the format of the MA name. string: indicates that the format of the MA name is string. icc-based: indicates that the format of the MA name is ICC-based. By default, the value is string.

OBJECT-TYPE

This object indicates the MA format name. The type/format of this object is determined by the value of the hwDot1agCfmMaFormatName object.

OBJECT-TYPE

This object indicates the name of the CCC associated with the MA.

OBJECT-TYPE

This object indicates the row status of this table. The writable columns in a row can not be changed if the row is active. All columns MUST have a valid value before a row can be activated.

OBJECT-IDENTITY

OBJECT-TYPE

This table is used to create a Maintenance Association End Point (MEP).

OBJECT-TYPE

The MEP table entry.

OBJECT-TYPE

This object indicates the ID of the MEP. Integer that is unique among all the MEPs in the same MA. MEP Identifier is also known as the MEPID. The value ranges from 1 to 8191.

OBJECT-TYPE

This object indicates whether the MEP in the MA is a VLAN-based MEP. If the MEP is a VLAN-based MEP, the MA must have been associated with a VLAN and the interface and VLAN information need not be configured. If the MEP is not a VLAN-based MEP, entry creation fails.

OBJECT-TYPE

This object indicates the interface to which the MEP is bound. The interface is either a bridge port, or an aggregated IEEE 802.1 link within a bridge port, to which the MEP is attached. By default, the value of IfIndex is 0.

OBJECT-TYPE

This object indicates the VLAN to which the interface that the MEP is bound to belong.

OBJECT-TYPE

This object indicates the QinQ PE VLAN bound to the MEP.

OBJECT-TYPE

This object indicates the QinQ CE VLAN bound to the MEP.

OBJECT-TYPE

This object indicates the direction in which the MEP sends the 802.1ag protocol packets. The value of this object can be: invalid: indicates the invalid value. dirInward: indicates that the 802.1ag protocol packets sent by an inward-facing MEP are transmitted through all the interfaces in the VLAN associated with the current MA (except the interface where the MEP resides). That is, an inward-facing MEP broadcasts the 802.1ag protocol packets in the VLAN associated with the current MA. dirOutward: indicates that the 802.1ag protocol packets sent by an outward-facing MEP are transmitted directly through the interface on which the MEP resides. By default, the value is invalid.

OBJECT-TYPE

This object indicates whether CCM sending is enabled on the MEP in an MA. The value of this object can be: enabled disabled By default, the value is disabled.

OBJECT-TYPE

This object indicates the MAC address of an MEP.

OBJECT-TYPE

This object indicates the row status of this table. The writable columns in a row can not be changed if the row is active. All columns MUST have a valid value before a row can be activated.

OBJECT-IDENTITY

OBJECT-TYPE

This table is used to create a Remote Maintenance Association End Point (RMEP).

OBJECT-TYPE

The remote MEP table entity.

OBJECT-TYPE

This object indicates the ID of the RMEP. The value ranges from 1 to 8191.

OBJECT-TYPE

This object indicates the MAC address of the interface the RMEP resides.

OBJECT-TYPE

This object indicates whether CCM receiving is enabled on the current device. The value can be: enabled disabled By default, the value is disabled.

OBJECT-TYPE

This object indicates the CFM status. The value can be: up: indicates that the CFM status is Up. down: indicates that the CFM status is Down. invalid: indicates that the CFM status is not enabled.

OBJECT-TYPE

This object indicates the severity level of the fault on an RMEP. If the CFM status is Up, this object is displayed as none.

OBJECT-TYPE

This object indicates the row status of this table. The writable columns in a row can not be changed if the row is active. All columns MUST have a valid value before a row can be activated.

OBJECT-IDENTITY

OBJECT-TYPE

This table is used to display information about a Maintenance Association Intermediate Point (MIP).

OBJECT-TYPE

The MIP table entry.

OBJECT-TYPE

This object indicates the interface on which the MIP resides.

OBJECT-TYPE

This object indicates the level of the MIP. The value ranges from 0 to 7.

OBJECT-TYPE

This object indicates the MAC address of the interface on which the MIP resides.

OBJECT-IDENTITY

OBJECT-TYPE

The entries related to the Mac Ping include the parameters input by users and the returned results.

OBJECT-TYPE

This table is used to configure the MAC ping function.

OBJECT-TYPE

This object indicates the index of this table.

OBJECT-TYPE

This object indicates whether the MAC ping function is enabled. The value can be: enabled disabled By default, the value is disabled.

OBJECT-TYPE

This object indicates the name of the MD where MAC ping is performed.

OBJECT-TYPE

This object indicates the name of the MA where MAC ping is performed.

OBJECT-TYPE

This object indicates the ID of the local MEP of the 802.1ag MAC ping operation. The value ranges from 1 to 8191. By default, the value is 0.

OBJECT-TYPE

This object indicates whether the destination MAC address of the LBM is the MAC address of the interface on which the RMEP resides.

OBJECT-TYPE

This object indicates the ID of the destination RMEP of the 802.1ag MAC ping operation. The value ranges from 1 to 8191. By default, the value is 0.

OBJECT-TYPE

This object indicates the destination MAC address of the LBM.

OBJECT-TYPE

This object indicates the outbound interface that sends the LBM.

OBJECT-TYPE

This object indicates the timeout period for waiting for the LBR. The value ranges from 1 to 65535 in milliseconds. By default, the value is 2000.

OBJECT-TYPE

This object indicates the number of ping operation times. The value ranges from 1 to 4294967295. By default, the value is 5.

OBJECT-TYPE

This object indicates the length of the LBM. The value ranges from 64 to 9500. By default, the value is 95.

OBJECT-TYPE

This object indicates the priority of the sent LBM packet. The value ranges from 0 to 7 or can be 255. The value 255 is an invalid value. If the value is set to 255, this value should be identical with the priority value of the MA which the MEP belongs to. The greater the value is, the higher the priority is.

OBJECT-TYPE

This object indicates the number of sent LBMs.

OBJECT-TYPE

This object indicates the number of received LBRs.

OBJECT-TYPE

This object indicates the frame loss ratio on the physical link. The value ranges from 0 to 100.

OBJECT-TYPE

This object indicates the minimum delay in receiving the LBM.

OBJECT-TYPE

This object indicates the maximum delay in receiving the LBM.

OBJECT-TYPE

This object indicates the average delay in receiving the LBM.

OBJECT-TYPE

This object indicates the row status of this table. The writable columns in a row can not be changed if the row is active. All columns MUST have a valid value before a row can be activated.

OBJECT-IDENTITY

OBJECT-TYPE

This table is used to configure the MAC trace function.

OBJECT-TYPE

Indicates the MAC Trace table entry.

OBJECT-TYPE

This object indicates the index of this table.

OBJECT-TYPE

This object indicates whether the MAC trace function is enabled. The value can be: enabled disabled By default, the value is disabled.

OBJECT-TYPE

This object indicates the name of the MD where MAC trace is performed.

OBJECT-TYPE

This object indicates the name of the MA where MAC trace is performed.

OBJECT-TYPE

This object indicates the ID of the local MEP of the 802.1ag MAC trace operation. The value ranges from 1 to 8191. By default, the value is 0.

OBJECT-TYPE

This object indicates whether the destination MAC address of the LTM is the MAC address of the interface on which the RMEP resides.

OBJECT-TYPE

This object indicates the ID of the destination RMEP of the 802.1ag MAC trace operation. The value ranges from 1 to 8191. By default, the value is 0.

OBJECT-TYPE

This object indicates the destination MAC address of the LTM.

OBJECT-TYPE

This object indicates the outbound interface that sends the LTM.

OBJECT-TYPE

This object indicates the timeout period for waiting for the LTR. The value ranges from 1 to 65535, in milliseconds. By default, the value is 2000.

OBJECT-TYPE

This object indicates the TTL value of the 802.1ag MAC trace operation. The value ranges from 1 to 255. By default, the value is 64.

OBJECT-TYPE

This object indicates the sequence number of the sent LTR.

OBJECT-TYPE

This object indicates the result of the MAC trace operation.

OBJECT-TYPE

This object indicates the row status of this table. The writable columns in a row can not be changed if the row is active. All columns MUST have a valid value before a row can be activated.

OBJECT-TYPE

This table is used to display information about the LTR for responding to the MAC trace operation.

OBJECT-TYPE

The Mac Trace result table entry.

OBJECT-TYPE

This object indicates the index of this table. The value is the sequence number of the LTR.

OBJECT-TYPE

This object indicates the index of this table. The value is the sequence in which the MAC trace results are displayed.

OBJECT-TYPE

This object indicates the TTL of the LTR. The value ranges from 0 to 255.

OBJECT-TYPE

This object indicates whether the device that sends the LTR keeps on forwarding LTMs.

OBJECT-TYPE

This object indicates whether the LTR is sent by an MEP.

OBJECT-TYPE

This object indicates the value of the Relay Action field in the LTR.

OBJECT-TYPE

This object indicates the value of the Ingress Action field in the LTR.

OBJECT-TYPE

This object indicates the physical MAC address carried in the ingress MAC address field in the LTR.

OBJECT-TYPE

This object indicates the name of the inbound interface of the LTR.

OBJECT-TYPE

This object indicates the value of the Egress Action field in the LTR.

OBJECT-TYPE

This object indicates the physical MAC address carried in the egress MAC address field in the LTR.

OBJECT-TYPE

This object indicates the name of the interface that forwards the LTR.

OBJECT-IDENTITY

OBJECT-TYPE

This table is used to get the index of the Maintenance Domain table.

OBJECT-TYPE

The Md Index table entry.

OBJECT-TYPE

This object indicates the name of the Maintenance Domain.

OBJECT-TYPE

This object indicates the index to the Maintenance Domain table.

OBJECT-TYPE

This table is used to get the index of the Maintenance Association table.

OBJECT-TYPE

The Ma Index table entry.

OBJECT-TYPE

This object indicates the name of Maintenance Association.

OBJECT-TYPE

This object indicates the index to the Maintenance Association table.

OBJECT-IDENTITY

OBJECT-TYPE

This object indicates whether GMAC trace function is enabled globally. The value of this object can be: Enabled: indicates that GMAC trace function is enabled globally. Disabled: indicates that GMAC trace function is disabled globally.

OBJECT-TYPE

This table is used to configure the GMAC trace function.

OBJECT-TYPE

Indicates the GMAC Trace table entry.

OBJECT-TYPE

This object indicates the index of this table.

OBJECT-TYPE

This object indicates whether the GMAC trace function is enabled. The value can be: enabled disabled By default, the value is disabled.

OBJECT-TYPE

This object indicates the destination MAC address of the LTM.

OBJECT-TYPE

This object indicates the service type associated with the gmac trace. The value of this object can be: vlan: indicates that a VLAN is associated with the gmac trace. invalid: indicates that no service type is specified for the gmac trace. By default, the value is invalid.

OBJECT-TYPE

This object indicates the VLAN to the destination MAC address.

OBJECT-TYPE

This object indicates the name of the VSI associated with the GMAC trace.

OBJECT-TYPE

This object indicates the ID of the L2VC associated with the GMAC trace.

OBJECT-TYPE

This object indicates the encapsulation type of the L2VC associated with the gmac trace. The value of this object can be: invalid: indicates that no display shows that the L2VC is associated with the current gmac trace. l2vcRaw: indicates that the VLAN tag is not encapsulated into the packet. l2vcTagged: indicates that the VLAN tag is encapsulated into the packet. By default, the value is invalid.

OBJECT-TYPE

This object indicates the DOT1Q VLAN ID to the destination MAC address.

OBJECT-TYPE

This object indicates the QinQ PE VLAN bound to the GMAC trace.

OBJECT-TYPE

This object indicates the QinQ CE VLAN bound to the GMAC trace.

OBJECT-TYPE

This object indicates the outbound interface that sends the LTM.

OBJECT-TYPE

This object indicates the timeout period for waiting for the LTR. The value ranges from 1 to 65535, in milliseconds. By default, the value is 2000.

OBJECT-TYPE

This object indicates whether the LTR include host information.

OBJECT-TYPE

This object indicates the sequence number of the sent LTR.

OBJECT-TYPE

This object indicates the result of the GMAC trace operation.

OBJECT-TYPE

This object indicates the row status of this table. The writable columns in a row can not be changed if the row is active. All columns MUST have a valid value before a row can be activated.

OBJECT-TYPE

This table is used to display information about the LTR for responding to the GMAC trace operation.

OBJECT-TYPE

The GMAC Trace result table entry.

OBJECT-TYPE

This object indicates the index of this table. The value is the sequence number of the LTR.

OBJECT-TYPE

This object indicates the index of this table. The value is the sequence in which the GMAC trace results are displayed.

OBJECT-TYPE

This object indicates the TTL of the LTR. The value ranges from 0 to 255.

OBJECT-TYPE

This object indicates whether the device that sends the LTR keeps on forwarding LTMs.

OBJECT-TYPE

This object indicates the host name and IP address of each hop.

OBJECT-TYPE

This object indicates the value of the Relay Action field in the LTR.

OBJECT-TYPE

This object indicates the value of the Ingress Action field in the LTR.

OBJECT-TYPE

This object indicates the physical MAC address carried in the ingress MAC address field in the LTR.

OBJECT-TYPE

This object indicates the name of the inbound interface of the LTR.

OBJECT-TYPE

This object indicates the value of the Egress Action field in the LTR.

OBJECT-TYPE

This object indicates the physical MAC address carried in the egress MAC address field in the LTR.

OBJECT-TYPE

This object indicates the name of the interface that forwards the LTR.

OBJECT-TYPE

This object indicates the MP address model of the CFM. The value of this object can be: bridge: indicates bridge MAC MP address model. individual: indicates individual MP address model.

OBJECT-IDENTITY

OBJECT-TYPE

Enable the EFM globally.

OBJECT-IDENTITY

OBJECT-TYPE

Set the detection mode table in the last one kilometer on the interface.

OBJECT-TYPE

Set the detection mode entity in the last one kilometer on the interface.

OBJECT-TYPE

Detection mode ( fast detection and standard detection)

OBJECT-TYPE

Time interval of detection

OBJECT-TYPE

Failure description from 802.3ah and from associated modules.

OBJECT-TYPE

This table contains the primary controls and status for the OAM capabilities of an Ethernet like interface. There will be one row in this table for each Ethernet like interface in the system that supports the OAM functions defined in [802.3ah].

OBJECT-TYPE

An entry in the table, containing information on the Ethernet OAM function for a single Ethernet like interface. Entries in the table are created automatically for each interface supporting Ethernet OAM. The status of the row entry can be determined from hwDot3ahEfmOperStatus. A hwDot3ahEfmEntry is indexed in the hwDot3ahEfmTable by the ifIndex object of the Interfaces MIB.

OBJECT-TYPE

This object is used to provision the default administrative OAM mode for this interface. This object represents the desired state of OAM for this interface. The hwDot3ahEfmAdminState always starts in the disabled(2) state until an explicit management action or configuration information retained by the system causes a transition to the enabled(1) state. When enabled(1), Ethernet OAM will attempt to operate over this interface.

OBJECT-TYPE

At initialization and failure conditions, two OAM entities on the same full-duplex Ethernet link begin a discovery phase to determine what OAM capabilities may be used on that link.

OBJECT-TYPE

This object configures the mode of OAM operation for this Ethernet like interface. OAM on Ethernet interfaces may be in 'active' mode or 'passive' mode.

OBJECT-TYPE

The largest OAMPDU that the OAM entity supports. OAM entities exchange maximum OAMPDU sizes and negotiate to use the smaller of the two maximum OAMPDU sizes between the peers. This value is determined by the local implementation.

OBJECT-TYPE

The configuration revision of the OAM entity as reflected in the latest OAMPDU sent by the OAM entity. The config revision is used by OAM entities to indicate configuration changes have occurred which might require the peer OAM entity to re-evaluate whether OAM peering is allowed.

OBJECT-TYPE

The OAM functions supported on this Ethernet like interface. OAM consists of separate functional sets beyond the basic discovery process which is always required. These functional groups can be supported independently by any implementation. These values are communicated to the peer via the local configuration field of Information OAMPDUs. Setting 'unidirectionalSupport(0)' indicates that the OAM entity supports the transmission of OAMPDUs on links that are operating in unidirectional mode (traffic flowing in one direction only). Setting 'loopbackSupport(1)' indicates the OAM entity can initiate and respond to loopback commands. Setting 'eventSupport(2)' indicates the OAM entity can send and receive Event Notification OAMPDUs. Setting 'variableSupport(3)' indicates the OAM entity can send and receive Variable Request and Response OAMPDUs.

OBJECT-TYPE

The EFM Timeout object defines the max time that the EFM session stays in detect mode since the last OAMPDU received. if there's no OAMPDU received within the time the timeout value defines, the EFM session will turn into discovery state. The value of EFM Timeout should be three or more times the value of the sending interval of the peer interface. The timeout value must be an exact integral multiple of 100. Range: 300-30000 Default: 5000 Unit: milliseconds

OBJECT-TYPE

The EFM interval object defines the interval of sending OAM PDUs. The value of EFM interval should be the same as the value of the peer interface. The interval value must be an exact integral multiple of 100. Range: 100-1000 Default: 1000 Unit: milliseconds

OBJECT-TYPE

This table contains information about the OAM peer for a particular Ethernet like interface. OAM entities communicate with a single OAM peer entity on Ethernet links on which OAM is enabled and operating properly. There is one entry in this table for each entry in the hwDot3ahEfmTable for which information on the peer OAM entity is available.

OBJECT-TYPE

An entry in the table, containing information on the peer OAM entity for a single Ethernet like interface. Note that there is at most one OAM peer for each Ethernet like interface. Entries are automatically created when information about the OAM peer entity becomes available, and automatically deleted when the OAM peer entity is no longer in communication. Peer information is not available when hwDot3ahEfmOperStatus is disabled(1), linkFault(2), passiveWait(3), activeSendLocal(4). or nonOperHalfDuplex(10)).

OBJECT-TYPE

The MAC address of the peer OAM entity. The MAC address is derived from the most recently received OAMPDU.

OBJECT-TYPE

The OUI of the OAM peer as reflected in the latest Information OAMPDU received with a Local Information TLV. The OUI can be used to identify the vendor of the remote OAM entity. This value is initialized to zero before any Local Information TLV is received.

OBJECT-TYPE

The Vendor Info of the OAM peer as reflected in the latest Information OAMPDU received with a Local Information TLV. The vendor information field is within the Local Information TLV, and can be used to determine additional information about the peer entity. The format of the vendor information is unspecified within the 32-bit field. This value is initialized to zero before any Local Information TLV is received.

OBJECT-TYPE

The mode of the OAM peer as reflected in the latest Information OAMPDU received with a Local Information TLV. The mode of the peer can be determined from the Configuration field in the Local Information TLV of the last Information OAMPDU received from the peer. The value is unknown(3) whenever no Local Information TLV has been received. The values of active(1) and passive(2) are returned when a Local Information TLV has been received indicating the peer is in active or passive mode, respectively.

OBJECT-TYPE

The maximum size of OAMPDU supported by the peer as reflected in the latest Information OAMPDU received with a Local Information TLV. Ethernet OAM on this interface must not use OAMPDUs that exceed this size. The maximum OAMPDU size can be determined from the PDU Configuration field of the Local Information TLV of the last Information OAMPDU received from the peer. A value of zero is returned if no Local Information TLV has been received. Otherwise, the value of the OAM peer's maximum OAMPDU size is returned in this value. Note that the values 1..65534 are invalid sizes for Ethernet frames and should never appear.

OBJECT-TYPE

The configuration revision of the OAM peer as reflected in the latest OAMPDU. This attribute is changed by the peer whenever it has a local configuration change for Ethernet OAM this interface. The configuration revision can be determined from the Revision field of the Local Information TLV of the most recently received Information OAMPDU with a Local Information TLV. A value of zero is returned if no Local Information TLV has been received.

OBJECT-TYPE

The OAM functions supported on this Ethernet like interface. OAM consists of separate functionality sets above the basic discovery process. This value indicates the capabilities of the peer OAM entity with respect to these functions. This value is initialized so all bits are clear. If unidirectionalSupport(0) is set, then the peer OAM entity supports sending OAM frames on Ethernet interfaces when the receive path is known to be inoperable. If loopbackSupport(1) is set, then the peer OAM entity can send and receive OAM loopback commands. If eventSupport(2) is set, then the peer OAM entity can send and receive event OAMPDUs to signal various error conditions. If variableSupport(3) is set, then the peer OAM entity can send and receive variable requests to monitor attribute value as described in Clause 57 of [802.3ah]. The capabilities of the OAM peer can be determined from the configuration field of the Local Information TLV of the most recently received Information OAMPDU with a Local Information TLV. All zeros are returned if no Local Information TLV has yet been received.

OBJECT-TYPE

This table contains controls for the loopback state of the local link as well as indicating the status of the loopback function. There is one entry in this table for each entry in hwDot3ahEfmTable that supports loopback functionality (where hwDot3ahEfmFunctionsSupported includes the loopbackSupport bit set). Loopback can be used to place the remote OAM entity in a state where every received frame (except OAMPDUs) is echoed back over the same interface on which they were received. In this state, at the remote entity, 'normal' traffic is disabled as only the looped back frames are transmitted on the interface. Loopback is thus an intrusive operation that prohibits normal data flow and should be used accordingly.

OBJECT-TYPE

An entry in the table, containing information on the loopback status for a single Ethernet like interface. Entries in the table are automatically created whenever the local OAM entity supports loopback capabilities. The loopback status on the interface can be determined from the hwDot3ahEfmLoopbackStatus object.

OBJECT-TYPE

The loopback status of the OAM entity. When operating in normal mode with no loopback in progress, the status reads noLoopback(1). The values initiatingLooopback(2) and terminatingLoopback(4) can be read or written. The other values can only be read - they can never be written.

OBJECT-TYPE

Since OAM loopback is a disruptive operation (user traffic does not pass), this attribute provides a mechanism to provide controls over whether received OAM loopback commands are processed or ignored. When the value is ignore(1), received loopback commands are ignored. When the value is process(2), OAM loopback commands are processed. The default value is to process loopback commands (process(2)).

OBJECT-TYPE

This object specifies the timeout period for a remote loopback. The value ranges from 0 to 1000 in minutes. The default value is 20 minutes. 0 indicates that no timeout period is set.

OBJECT-TYPE

This table contains statistics for the OAM function on a particular Ethernet like interface. There is an entry in the table for every entry in the hwDot3ahEfmTable. The counters in this table are defined as 32-bit entries to match the counter size as defined in [802.3ah]. Given the OAM protocol is a slow protocol, the counters increment at a slow rate.

OBJECT-TYPE

An entry in the table, containing statistics information on the Ethernet OAM function for a single Ethernet like interface. Entries are automatically created for every entry in the hwDot3ahEfmTable. Counters are maintained across transitions in hwDot3ahEfmOperStatus.

OBJECT-TYPE

A count of the number of Information OAMPDUs transmitted on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.

OBJECT-TYPE

A count of the number of Information OAMPDUs received on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.

OBJECT-TYPE

A count of the number of unique Event OAMPDUs transmitted on this interface. Event notifications may be sent in duplicate to increase the probability of successfully being received, given the possibility that a frame may be lost in transit. Duplicate Event Notification transmissions are counted by hwDot3ahEfmDuplicateEventNotificationTx. A unique Event Notification OAMPDU is indicated as an Event Notification OAMPDU with a Sequence Number field that is distinct from the previously transmitted Event Notification OAMPDU Sequence Number. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.

OBJECT-TYPE

A count of the number of unique Event OAMPDUs received on this interface. Event notification OAMPDUs may be sent in duplicate to increase the probability of successfully being received, given the possibility that a frame may be lost in transit. Duplicate Event Notification receptions are counted by hwDot3ahEfmDuplicateEventNotificationRx. A unique Event Notification OAMPDU is indicated as an Event Notification OAMPDU with a Sequence Number field that is distinct from the previously received Event Notification OAMPDU Sequence Number. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.

OBJECT-TYPE

A count of the number of duplicate Event OAMPDUs transmitted on this interface. Event notification OAMPDUs may be sent in duplicate to increase the probability of successfully being received, given the possibility that a frame may be lost in transit. A duplicate Event Notification OAMPDU is indicated as an Event Notification OAMPDU with a Sequence Number field that is identical to the previously transmitted Event Notification OAMPDU Sequence Number. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.

OBJECT-TYPE

A count of the number of duplicate Event OAMPDUs received on this interface. Event notification OAMPDUs may be sent in duplicate to increase the probability of successfully being received, given the possibility that a frame may be lost in transit. A duplicate Event Notification OAMPDU is indicated as an Event Notification OAMPDU with a Sequence Number field that is identical to the previously received Event Notification OAMPDU Sequence Number. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.

OBJECT-TYPE

A count of the number of Loopback Control OAMPDUs transmitted on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.

OBJECT-TYPE

A count of the number of Loopback Control OAMPDUs received on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.

OBJECT-TYPE

A count of the number of Variable Request OAMPDUs transmitted on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.

OBJECT-TYPE

A count of the number of Variable Request OAMPDUs received on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.

OBJECT-TYPE

A count of the number of Variable Response OAMPDUs transmitted on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.

OBJECT-TYPE

A count of the number of Variable Response OAMPDUs received on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.

OBJECT-TYPE

A count of the number of Organization Specific OAMPDUs transmitted on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.

OBJECT-TYPE

A count of the number of Organization Specific OAMPDUs received on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.

OBJECT-TYPE

A count of the number of OAMPDUs transmitted on this interface with an unsupported op-code. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.

OBJECT-TYPE

A count of the number of OAMPDUs received on this interface with an unsupported op-code. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.

OBJECT-TYPE

A count of the number of frames that were dropped by the OAM multiplexer. Since the OAM multiplexer has multiple inputs and a single output, there may be cases where frames are dropped due to transmit resource contention. This counter is incremented whenever a frame is dropped by the OAM layer. Note that any Ethernet frame, not just OAMPDUs, may be dropped by the OAM layer. This can occur when an OAMPDU takes precedence over a 'normal' frame resulting in the 'normal' frame being dropped. When this counter is incremented, no other counters in this MIB are incremented. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.

OBJECT-TYPE

Ethernet OAM includes the ability to generate and receive Event Notification OAMPDUs to indicate various link problems. This table contains the mechanisms to enable Event Notifications and configure the thresholds to generate the standard Ethernet OAM events. There is one entry in the table for every entry in hwDot3ahEfmTable that supports OAM events (where hwDot3ahEfmFunctionsSupported includes the eventSupport bit set). The values in the table are maintained across changes to hwDot3ahEfmOperStatus. The standard threshold crossing events are: - Errored Symbol Period Event. Generated when the number of symbol errors exceeds a threshold within a given window defined by a number of symbols (for example, 1,000 symbols out of 1,000,000 had errors). - Errored Frame Period Event. Generated when the number of frame errors exceeds a threshold within a given window defined by a number of frames (for example, 10 frames out of 1000 had errors). - Errored Frame Event. Generated when the number of frame errors exceeds a threshold within a given window defined by a period of time (for example, 10 frames in 1 second had errors). - Errored Frame Seconds Summary Event. Generated when the number of errored frame seconds exceeds a threshold within a given time period (for example, 10 errored frame seconds within the last 100 seconds). An errored frame second is defined as a 1 second interval which had >0 frame errors. There are other events (dying gasp, critical events) that are not threshold crossing events but which can be enabled/disabled via this table.

OBJECT-TYPE

Entries are automatically created and deleted from this table, and exist whenever the OAM entity supports Ethernet OAM events (as indicated by the eventSupport bit in hwDot3ahEfmFunctionsSuppported). Values in the table are maintained across changes to the value of hwDot3ahEfmOperStatus. Event configuration controls when the local management entity sends Event Notification OAMPDUs to its OAM peer, and when certain event flags are set or cleared in OAMPDUs.

OBJECT-TYPE

The two objects hwDot3ahEfmErrSymPeriodWindowHi and hwDot3ahEfmErrSymPeriodWindowLo together form an unsigned 64-bit integer representing the number of symbols over which this threshold event is defined. This is defined as hwDot3ahEfmErrSymPeriodWindow = ((2^32)*hwDot3ahEfmErrSymPeriodWindowHi) + hwDot3ahEfmErrSymPeriodWindowLo If hwDot3ahEfmErrSymPeriodThreshold symbol errors occur within a window of hwDot3ahEfmErrSymPeriodWindow symbols, an Event Notification OAMPDU should be generated with an Errored Symbol Period Event TLV indicating the threshold has been crossed in this window. The default value for hwDot3ahEfmErrSymPeriodWindow is the number of symbols in one second for the underlying physical layer.

OBJECT-TYPE

The two objects hwDot3ahEfmErrSymPeriodWindowHi and hwDot3ahEfmErrSymPeriodWindowLo together form an unsigned 64-bit integer representing the number of symbols over which this threshold event is defined. This is defined as hwDot3ahEfmErrSymPeriodWindow = ((2^32)*hwDot3ahEfmErrSymPeriodWindowHi) + hwDot3ahEfmErrSymPeriodWindowLo If hwDot3ahEfmErrSymPeriodThreshold symbol errors occur within a window of hwDot3ahEfmErrSymPeriodWindow symbols, an Event Notification OAMPDU should be generated with an Errored Symbol Period Event TLV indicating the threshold has been crossed in this window. The default value for hwDot3ahEfmErrSymPeriodWindow is the number of symbols in one second for the underlying physical layer.

OBJECT-TYPE

The two objects hwDot3ahEfmErrSymPeriodThresholdHi and hwDot3ahEfmErrSymPeriodThresholdLo together form an unsigned 64-bit integer representing the number of symbol errors that must occur within a given window to cause this event. This is defined as hwDot3ahEfmErrSymPeriodThreshold = ((2^32) * hwDot3ahEfmErrSymPeriodThresholdHi) + hwDot3ahEfmErrSymPeriodThresholdLo If hwDot3ahEfmErrSymPeriodThreshold symbol errors occur within a window of hwDot3ahEfmErrSymPeriodWindow symbols, an Event Notification OAMPDU should be generated with an Errored Symbol Period Event TLV indicating the threshold has been crossed in this window. The default value for hwDot3ahEfmErrSymPeriodThreshold is one symbol errors. If the threshold value is zero, then an Event Notification OAMPDU is sent periodically (at the end of every window). This can be used as an asynchronous notification to the peer OAM entity of the statistics related to this threshold crossing alarm.

OBJECT-TYPE

The two objects hwDot3ahEfmErrSymPeriodThresholdHi and hwDot3ahEfmErrSymPeriodThresholdLo together form an unsigned 64-bit integer representing the number of symbol errors that must occur within a given window to cause this event. This is defined as hwDot3ahEfmErrSymPeriodThreshold = ((2^32) * hwDot3ahEfmErrSymPeriodThresholdHi) + hwDot3ahEfmErrSymPeriodThresholdLo If hwDot3ahEfmErrSymPeriodThreshold symbol errors occur within a window of hwDot3ahEfmErrSymPeriodWindow symbols, an Event Notification OAMPDU should be generated with an Errored Symbol Period Event TLV indicating the threshold has been crossed in this window. The default value for hwDot3ahEfmErrSymPeriodThreshold is one symbol error. If the threshold value is zero, then an Event Notification OAMPDU is sent periodically (at the end of every window). This can be used as an asynchronous notification to the peer OAM entity of the statistics related to this threshold crossing alarm.

OBJECT-TYPE

If true, the OAM entity should send an Event Notification OAMPDU when an Errored Symbol Period Event occurs. By default, this object should have the value true for Ethernet like interfaces that support OAM. If the OAM layer does not support event notifications (as indicated via the hwDot3ahEfmFunctionsSupported attribute), this value is ignored.

OBJECT-TYPE

The number of frames over which the threshold is defined. The default value of the window is the number of minimum size Ethernet frames that can be received over the physical layer in one second. If hwDot3ahEfmErrFramePeriodThreshold frame errors occur within a window of hwDot3ahEfmErrFramePeriodWindow frames, an Event Notification OAMPDU should be generated with an Errored Frame Period Event TLV indicating the threshold has been crossed in this window.

OBJECT-TYPE

The number of frame errors that must occur for this event to be triggered. The default value is one frame error. If the threshold value is zero, then an Event Notification OAMPDU is sent periodically (at the end of every window). This can be used as an asynchronous notification to the peer OAM entity of the statistics related to this threshold crossing alarm. If hwDot3ahEfmErrFramePeriodThreshold frame errors occur within a window of hwDot3ahEfmErrFramePeriodWindow frames, an Event Notification OAMPDU should be generated with an Errored Frame Period Event TLV indicating the threshold has been crossed in this window.

OBJECT-TYPE

If true, the OAM entity should send an Event Notification OAMPDU when an Errored Frame Period Event occurs. By default, this object should have the value true for Ethernet like interfaces that support OAM. If the OAM layer does not support event notifications (as indicated via the hwDot3ahEfmFunctionsSupported attribute), this value is ignored.

OBJECT-TYPE

The amount of time (in 100ms increments) over which the threshold is defined. The default value is 10 (1 second). If hwDot3ahEfmErrFrameThreshold frame errors occur within a window of hwDot3ahEfmErrFrameWindow seconds (measured in tenths of seconds), an Event Notification OAMPDU should be generated with an Errored Frame Event TLV indicating the threshold has been crossed in this window.

OBJECT-TYPE

The number of frame errors that must occur for this event to be triggered. The default value is one frame error. If the threshold value is zero, then an Event Notification OAMPDU is sent periodically (at the end of every window). This can be used as an asynchronous notification to the peer OAM entity of the statistics related to this threshold crossing alarm. If hwDot3ahEfmErrFrameThreshold frame errors occur within a window of hwDot3ahEfmErrFrameWindow (in tenths of seconds), an Event Notification OAMPDU should be generated with an Errored Frame Event TLV indicating the threshold has been crossed in this window.

OBJECT-TYPE

If true, the OAM entity should send an Event Notification OAMPDU when an Errored Frame Event occurs. By default, this object should have the value true for Ethernet like interfaces that support OAM. If the OAM layer does not support event notifications (as indicated via the hwDot3ahEfmFunctionsSupported attribute), this value is ignored.

OBJECT-TYPE

The amount of time (in 100ms intervals) over which the threshold is defined. The default value is 600 (60 seconds). If hwDot3ahEfmErrFrameSecsSummaryThreshold frame errors occur within a window of hwDot3ahEfmErrFrameSecsSummaryWindow (in tenths of seconds), an Event Notification OAMPDU should be generated with an Errored Frame Seconds Summary Event TLV indicating the threshold has been crossed in this window.

OBJECT-TYPE

The number of errored frame seconds that must occur for this event to be triggered. The default value is one errored frame second. If the threshold value is zero, then an Event Notification OAMPDU is sent periodically (at the end of every window). This can be used as an asynchronous notification to the peer OAM entity of the statistics related to this threshold crossing alarm. If hwDot3ahEfmErrFrameSecsSummaryThreshold frame errors occur within a window of hwDot3ahEfmErrFrameSecsSummaryWindow (in tenths of seconds), an Event Notification OAMPDU should be generated with an Errored Frame Seconds Summary Event TLV indicating the threshold has been crossed in this window.

OBJECT-TYPE

If true, the local OAM entity should send an Event Notification OAMPDU when an Errored Frame Seconds Event occurs. By default, this object should have the value true for Ethernet like interfaces that support OAM. If the OAM layer does not support event notifications (as indicated via the hwDot3ahEfmFunctionsSupported attribute), this value is ignored.

OBJECT-TYPE

If true, the local OAM entity should attempt to indicate a dying gasp via the OAMPDU flags field to its peer OAM entity when a dying gasp event occurs. The exact definition of a dying gasp event is implementation dependent. If the system does not support dying gasp capability, setting this object has no effect, and reading the object should always result in 'false'. By default, this object should have the value true for Ethernet like interfaces that support OAM. If the OAM layer does not support event notifications (as indicated via the hwDot3ahEfmFunctionsSupported attribute), this value is ignored.

OBJECT-TYPE

If true, the local OAM entity should attempt to indicate a critical event via the OAMPDU flags to its peer OAM entity when a critical event occurs. The exact definition of a critical event is implementation dependent. If the system does not support critical event capability, setting this object has no effect, and reading the object should always result in 'false'. By default, this object should have the value true for Ethernet like interfaces that support OAM. If the OAM layer does not support event notifications (as indicated via the hwDot3ahEfmFunctionsSupported attribute), this value is ignored.

OBJECT-TYPE

This object indicates whether threshold event will trigger error-shutdown. If it is enabled(1), after EFM checks that the threshold event happens, the current interface will be set to administrative down. The default value is disabled(2).

OBJECT-TYPE

This object indicates whether non-threshold critical event will trigger error-shutdown. If it is enabled(1), after EFM checks that the non-threshold critical event happens, the current interface will be set to administrative down. The default value is disabled(2).

OBJECT-TYPE

This object indicates whether non-threshold dying gasp event will trigger error-shutdown. If it is enabled(1), after EFM checks that the non-threshold dying gasp event happens, the current interface will be set to administrative down. The default value is disabled(2).

OBJECT-TYPE

This object indicates whether non-threshold link fault event will trigger error-shutdown. If it is enabled(1), after EFM checks that the non-threshold link fault event happens, the current interface will be set to administrative down. The default value is disabled(2).

OBJECT-TYPE

This object indicates whether non-threshold time out event will trigger error-shutdown. If it is enabled(1), after EFM checks that the non-threshold time out event happens, the current interface will be set to administrative down. The default value is disabled(2).

OBJECT-TYPE

This table records a history of the events that have occurred at the Ethernet OAM level. These events can include locally detected events, which may result in locally generated OAMPDUs, and remotely detected events, which are detected by the OAM peer entity and signaled to the local entity via Ethernet OAM. Ethernet OAM events can be signaled by Event Notification OAMPDUs or by the flags field in any OAMPDU. This table contains both threshold crossing events and non-threshold crossing events. The parameters for the threshold window, threshold value, and actual value (hwDot3ahEfmEventLogWindowXX, hwDot3ahEfmEventLogThresholdXX, hwDot3ahEfmEventLogValue) are only applicable to threshold crossing events, and are returned as all F's (2^32 - 1) for non-threshold crossing events. Entries in the table are automatically created when such events are detected. The size of the table is implementation dependent. When the table reaches its maximum size, older entries are automatically deleted to make room for newer entries.

OBJECT-TYPE

An entry in the hwDot3ahEfmEventLogTable. Entries are automatically created whenever Ethernet OAM events occur at the local OAM entity, and when Event Notification OAMPDUs are received at the local OAM entity (indicating events have occurred at the peer OAM entity). The size of the table is implementation dependent, but when the table becomes full, older events are automatically deleted to make room for newer events. The table index hwDot3ahEfmEventLogIndex increments for each new entry, and when the maximum value is reached the value restarts at zero.

OBJECT-TYPE

An arbitrary integer for identifying individual events within the event log.

OBJECT-TYPE

The value of sysUpTime at the time of the logged event. For locally generated events, the time of the event can be accurately retrieved from sysUpTime. For remotely generated events, the time of the event is indicated by the reception of the Event Notification OAMPDU indicating the event occurred on the peer. A system may attempt to adjust the timestamp value to more accurately reflect the time of the event at the peer OAM entity by using other information, such as that found in the timestamp found of the Event Notification TLVs, which provides an indication of the relative time between events at the peer entity.

OBJECT-TYPE

The OUI of the entity defining the object type. All IEEE 802.3 defined events (as appearing in [802.3ah] except for the Organizationally Unique Event TLVs) use the IEEE 802.3 OUI of 0x0180C2. Organizations defining their own Event Notification TLVs include their OUI in the Event Notification TLV which gets reflected here.

OBJECT-TYPE

The type of event that generated this entry in the event log. When the OUI is the IEEE 802.3 OUI of 0x0180C2, the following event types are defined: erroredSymbolEvent(1), erroredFrameEvent(2), erroredFramePeriodEvent(3), erroredFrameSecondsEvent(4), lostlink(254), linkFault(256), dyingGaspEvent(257), criticalLinkEvent(258) The first four are considered threshold crossing events as they are generated when a metric exceeds a given value within a specified window. The other three are not threshold crossing events. When the OUI is not 71874 (0x0180C2 in hex), then some other organization has defined the event space. If event subtyping is known to the implementation, it may be reflected here. Otherwise, this value should return all Fs (2^32 - 1).

OBJECT-TYPE

Whether this event occurred locally (local(1)), or was received from the OAM peer via Ethernet OAM (remote(2)).

OBJECT-TYPE

If the event represents a threshold crossing event, the two objects hwDot3ahEfmEventWindowHi and hwDot3ahEfmEventWindowLo form an unsigned 64-bit integer yielding the window over which the value was measured for the threshold crossing event (for example, 5, when 11 occurrences happened in 5 seconds while the threshold was 10). The two objects are combined as: hwDot3ahEfmEventLogWindow = ((2^32) * hwDot3ahEfmEventLogWindowHi) + hwDot3ahEfmEventLogWindowLo Otherwise, this value is returned as all F's (2^32 - 1) and adds no useful information.

OBJECT-TYPE

If the event represents a threshold crossing event, the two objects hwDot3ahEfmEventWindowHi and hwDot3ahEfmEventWindowLo form an unsigned 64-bit integer yielding the window over which the value was measured for the threshold crossing event (for example, 5, when 11 occurrences happened in 5 seconds while the threshold was 10). The two objects are combined as: hwDot3ahEfmEventLogWindow = ((2^32) * hwDot3ahEfmEventLogWindowHi) + hwDot3ahEfmEventLogWindowLo Otherwise, this value is returned as all F's (2^32 - 1) and adds no useful information.

OBJECT-TYPE

If the event represents a threshold crossing event, the two objects hwDot3ahEfmEventThresholdHi and hwDot3ahEfmEventThresholdLo form an unsigned 64-bit integer yielding the value that was crossed for the threshold crossing event (for example, 10, when 11 occurrences happened in 5 seconds while the threshold was 10). The two objects are combined as: hwDot3ahEfmEventLogThreshold = ((2^32) * hwDot3ahEfmEventLogThresholdHi) + hwDot3ahEfmEventLogThresholdLo Otherwise, this value is returned as all F's (2^32 -1) and adds no useful information.

OBJECT-TYPE

If the event represents a threshold crossing event, the two objects hwDot3ahEfmEventThresholdHi and hwDot3ahEfmEventThresholdLo form an unsigned 64-bit integer yielding the value that was crossed for the threshold crossing event (for example, 10, when 11 occurrences happened in 5 seconds while the threshold was 10). The two objects are combined as: hwDot3ahEfmEventLogThreshold = ((2^32) * hwDot3ahEfmEventLogThresholdHi) + hwDot3ahEfmEventLogThresholdLo Otherwise, this value is returned as all F's (2^32 - 1) and adds no useful information.

OBJECT-TYPE

If the event represents a threshold crossing event, this value indicates the value of the parameter within the given window that generated this event (for example, 11, when 11 occurrences happened in 5 seconds while the threshold was 10). Otherwise, this value is returned as all F's (2^64 - 1) and adds no useful information.

OBJECT-TYPE

Each Event Notification TLV contains a running total of the number of times an event has occurred, as well as the number of times an Event Notification for the event has been transmitted. For non-threshold crossing events, the number of events (hwDot3ahEfmLogRunningTotal) and the number of resultant Event Notifications (hwDot3ahEfmLogEventTotal) should be identical. For threshold crossing events, since multiple occurrences may be required to cross the threshold, these values are likely different. This value represents the total number of times this event has happened since the last reset (for example, 3253, when 3253 symbol errors have occurred since the last reset, which has resulted in 51 symbol error threshold crossing events since the last reset).

OBJECT-TYPE

Each Event Notification TLV contains a running total of the number of times an event has occurred, as well as the number of times an Event Notification for the event has been transmitted. For non-threshold crossing events, the number of events (hwDot3ahEfmLogRunningTotal) and the number of resultant Event Notifications (hwDot3ahEfmLogEventTotal) should be identical. For threshold crossing events, since multiple occurrences may be required to cross the threshold, these values are likely different. This value represents the total number of times one or more of these occurrences have resulted in an Event Notification (for example, 51 when 3253 symbol errors have occurred since the last reset, which has resulted in 51 symbol error threshold crossing events since the last reset).

OBJECT-TYPE

This table contains configurations of binding relationships between EFM and other modules.

OBJECT-TYPE

This entry contains configurations of binding relationships between EFM and other modules.

OBJECT-TYPE

This object indicates whether EFM is bound to the interface. If it is enabled(1), after EFM checks that the link times out, the current Ethernet interface link state will be set to block (EFM down),and all the data except the OAMPDU is blocked. The default value is disabled(2).

OBJECT-TYPE

This object specifies the time elapsed an EFM interface is in the faulty state. The value ranges from 0 to 50 in seconds. The default value is 0.

OBJECT-TYPE

This table contains information about the OAM Evrrp project for a particular Ethernet like interface.

OBJECT-TYPE

An entry in the table of hwDot3ahEvrrpTable, containing information on the OAM Evrrp entity for a single Ethernet like interface. Note that there is at most one OAM Evrrp for each Ethernet like interface.

OBJECT-TYPE

This object indicates the state in the OAMPDU which sended by the peer interface. If it is master(1), EFM will make the link work as the master state. And if it is slave(2), EFM will make the link works as the slave chain link. The default state is unknown(3). That means the peer interface didn't send any OAMPDU which contains the state of link status.

OBJECT-TYPE

This object indicates whether EFM is bound to the interface. If it is enabled(1), after EFM checks that the link times out, the current Ethernet interface link state will be set to EFM down. And all of the PDU operation will be stop. The default value is disabled(2).

OBJECT-TYPE

This object specifies the time elapsed an EFM interface is in the faulty state. The value ranges from 0 to 50 in seconds. The default value is 0.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

Search the next hwTestMessageTable instance.

OBJECT-TYPE

The definition of the tested packets format and the transmission of the tested packets

OBJECT-TYPE

Entry for Test Message Table.

OBJECT-TYPE

Set the index for the tested packets table

OBJECT-TYPE

The destination MAC address

OBJECT-TYPE

VLAN index

OBJECT-TYPE

If the interface is specified, specify the interface name.

OBJECT-TYPE

Name of the service instance

OBJECT-TYPE

The length of the sent tested packets ranges from 64 to 1518 in byte, and the default value is 64.

OBJECT-TYPE

The number of the sent tested packets ranges from 1 to 65535 in integer, and the default value is 5.

OBJECT-TYPE

Enumerated type indicates the rate of sending the packets: oneMbps and fiveMbps. The default is oneMbps.

OBJECT-TYPE

The sending and termination of the tested packets

OBJECT-TYPE

View whether the tested packets are stopped to be sent: 1, 2, 3, 4, and 5 indicate that has not run/is running/the previous test terminates normally/the previous test terminates abnormally/the previous test is interrupted (through ctrl+c or mib)

OBJECT-TYPE

The status of the row. The writable columns in a row can not be changed if the row is active. All columns must have a valid value before a row can be activated.

OBJECT-TYPE

View the returned results after tests

OBJECT-TYPE

Entry for Test Message Table.

OBJECT-TYPE

The number of the sent packets

OBJECT-TYPE

The number of the received packets

OBJECT-TYPE

Packets loss ratio

OBJECT-TYPE

The number of the sent bytes

OBJECT-TYPE

The number of the received bytes

OBJECT-TYPE

The number of the lost bytes

OBJECT-TYPE

The time of starting the Test operation

OBJECT-TYPE

The time of ending the Test operation

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

This table is used to configure OAM functions for base.

OBJECT-TYPE

The configuration entry of base config.

OBJECT-TYPE

This object indicates the PW measure mode. The value can be: invalid symmetry asymmetry If MA associates with a VLAN, the value is invalid. If MA associates with VSI or VLL, the default value is asymmetry.

OBJECT-TYPE

This object indicates the alarm threshold for the one-way ETH-DM. This object can be set only in VLAN. The value ranges from 1 to 4294967295. If hwY1731OneDelayThreshold is set to 0, the default alarm threshold of the one-way frame delay is used. By default, no alarm threshold of the one-way frame delay is set.

OBJECT-TYPE

This object indicates the alarm threshold for the two-way ETH-DM. This object can be set only in VLAN. The value ranges from 1 to 4294967295. If hwY1731TwoDelayThreshold is set to 0, the default alarm threshold of the two-way frame delay is used. By default, no alarm threshold of the two-way frame delay is set.

OBJECT-TYPE

This table is used to configure OAM functions for performance monitoring.

OBJECT-TYPE

The configuration entry of performance monitoring functions.

OBJECT-TYPE

This object indicates the IP address of the remote end.

OBJECT-TYPE

This object indicates the VC ID.

OBJECT-TYPE

This object indicates the MAC address of the remote end.

OBJECT-TYPE

This object indicates the index for reserve.

OBJECT-TYPE

This object indicates the type of service. The service can be: vlan vsi vll unbind

OBJECT-TYPE

This object indicates whether the single-ended ETH-LM receiving is enabled on the MEP in the MA to implement the single-ended ETH-LM. The value can be: enabled disabled By default, the value is disabled.

OBJECT-TYPE

This object indicates whether the one-way ETH-DM receiving is enabled on the MEP in the MA to implement the one-way ETH-DM. The value can be: enabled disabled By default, the value is disabled.

OBJECT-TYPE

This object indicates whether the one-way ETH-DM receiving is continual.

OBJECT-TYPE

This object indicates whether the two-way ETH-DM receiving is enabled on the MEP in the MA to implement the two-way ETH-DM. The value can be: enabled disabled By default, the value is disabled.

OBJECT-TYPE

This object indicates whether the single-ended ETH-LM sending is enabled. The value can be: enabled disabled By default, the value is disabled.

OBJECT-TYPE

This object indicates whether the single-ended ETH-LM sending is continual. If the value is 'false', it indicates that the single-ended ETH-LM is on-demand.

OBJECT-TYPE

This object indicates the ID of the local MEP that is specified in the single-ended ETH-LM operation. The value can be 0 or ranges from 1 to 8191. The value 0 is an invalid value.

OBJECT-TYPE

This object indicates whether the destination MAC address of the single-ended ETH-LM is the specified RMEP's MAC address.

OBJECT-TYPE

This object indicates the ID of the remote MEP that is specified in the single-ended ETH-LM operation. The value 0 is an invalid value.

OBJECT-TYPE

This object indicates the MAC address of the remote end.

OBJECT-TYPE

This object indicates the interval of the sent LMM frames. When on-demand OAM, the value can be: 1 second 10 seconds When proactive OAM, the value can be: 1 second 10 seconds 30 seconds

OBJECT-TYPE

This object indicates the number of LMM frames to be sent. The value can be 0 or ranges from 1 to 60. When proactive OAM, the value is 0.

OBJECT-TYPE

This object indicates the 802.1p priority of the sent LMM packets. The priority value ranges from 0 to 7. It maps a 8 bits number. 0 - 1 (0x01) 1 - 2 (0x02) 2 - 4 (0x04) 3 - 8 (0x08) 4 - 16 (0x10) 5 - 32 (0x20) 6 - 64 (0x40) 7 - 128(0x80) For example, if 802.1p priority is 0 , 4 , 7, the value is 145(1 + 16 + 128). The value 0 indicates that the priority is not set.

OBJECT-TYPE

This object indicates whether the dual-ended ETH-LM is enabled. The value can be: enabled disabled By default, the value is disabled.

OBJECT-TYPE

This object indicates the ID of the local MEP that is specified in the dual-ended ETH-LM operation. The value can be 0 or ranges from 1 to 8191. The value 0 is an invalid value.

OBJECT-TYPE

This object indicates the ID of the remote MEP that is specified in the dual-ended ETH-LM operation. The value can be 0 or ranges from 1 to 8191. The value 0 is an invalid value.

OBJECT-TYPE

This object indicates whether the one-way ETH-DM sending is enabled. The value can be: enabled disabled By default, the value is disabled.

OBJECT-TYPE

This object indicates whether the one-way ETH-DM sending is continual. If the value is 'false', it indicates that the one-way ETH-DM is on-demand.

OBJECT-TYPE

This object indicates the ID of the local MEP that is specified in the one-way ETH-DM operation. The value can be 0 or ranges from 1 to 8191. The value 0 is an invalid value.

OBJECT-TYPE

This object indicates whether the destination MAC address of the one-way ETH-DM is the specified RMEP's MAC address.

OBJECT-TYPE

This object indicates the ID of the remote MEP that is specified in the one-way ETH-DM operation. The value can be 0 or ranges from 1 to 8191. The value 0 is an invalid value.

OBJECT-TYPE

This object indicates the MAC address of the RMEP.

OBJECT-TYPE

This object indicates the interval of the sent 1DM frames. When on-demand OAM, the value can be: 1 second 10 seconds When proactive OAM, the value can be: 1 second 10 seconds 30 seconds

OBJECT-TYPE

This object indicates the number of the sent 1DM frames. The value can be 0 or ranges from 1 to 60. When proactive OAM, the value is 0.

OBJECT-TYPE

This object indicates the 802.1p priority of the sent 1DM packets. The priority value ranges from 0 to 7. It maps a 8 bits number. 0 - 1 (0x01) 1 - 2 (0x02) 2 - 4 (0x04) 3 - 8 (0x08) 4 - 16 (0x10) 5 - 32 (0x20) 6 - 64 (0x40) 7 - 128(0x80) For example, if 802.1p priority is 0, 4 , 7, the value is 145(1 + 16 + 128). The value 0 indicates that the priority is not set.

OBJECT-TYPE

This object indicates whether the two-way ETH-DM sending is enabled.

OBJECT-TYPE

This object indicates whether the two-way ETH-DM sending is continual. If the value is 'false', it indicates that the two-way ETH-DM is on-demand.

OBJECT-TYPE

This object indicates the ID of the local MEP that is specified in the two-way ETH-DM operation. The value can be 0 or ranges from 1 to 8191. The value 0 is an invalid value.

OBJECT-TYPE

This object indicates whether the destination MAC address of the two-way ETH-DM is the specified RMEP's MAC address.

OBJECT-TYPE

This object indicates the ID of the remote MEP that is specified in the two-way ETH-DM operation. The value can be 0 or ranges from 1 to 8191. The value 0 is an invalid value.

OBJECT-TYPE

This object indicates the destination MAC address.

OBJECT-TYPE

This object indicates the interval of the sent DMM frames. When on-demand OAM, the value can be: 1 second 10 seconds When proactive OAM, the value can be: 1 second 10 seconds 30 seconds

OBJECT-TYPE

This object indicates the number of the sent DMM frames. The value can be 0 or ranges from 1 to 60. When proactive OAM, the value is 0.

OBJECT-TYPE

This object indicates the 802.1p priority of the sent DMM packets. The priority value ranges from 0 to 7. It maps a 8 bits number. 0 - 1 (0x01) 1 - 2 (0x02) 2 - 4 (0x04) 3 - 8 (0x08) 4 - 16 (0x10) 5 - 32 (0x20) 6 - 64 (0x40) 7 - 128(0x80) For example, if 802.1p priority is 0 , 4 , 7, the value is 145(1 + 16 + 128). The value 0 indicates that the priority is not set.

OBJECT-TYPE

This object indicates the 802.1p priority of the received LMM packets. The priority value ranges from 0 to 7. It maps a 8 bits number. 0 - 1 (0x01) 1 - 2 (0x02) 2 - 4 (0x04) 3 - 8 (0x08) 4 - 16 (0x10) 5 - 32 (0x20) 6 - 64 (0x40) 7 - 128(0x80) For example, if 802.1p priority is 0 , 4 , 7, the value is 145(1 + 16 + 128). The value 0 indicates that the priority is not set.

OBJECT-TYPE

This object indicates the 802.1p priority of the received 1DM packets. The priority value ranges from 0 to 7. It maps a 8 bits number. 0 - 1 (0x01) 1 - 2 (0x02) 2 - 4 (0x04) 3 - 8 (0x08) 4 - 16 (0x10) 5 - 32 (0x20) 6 - 64 (0x40) 7 - 128(0x80) For example, if 802.1p priority is 0 , 4 , 7, the value is 145(1 + 16 + 128). The value 0 indicates that the priority is not set.

OBJECT-TYPE

This object indicates the 802.1p priority of the received DMM packets. The priority value ranges from 0 to 7. It maps a 8 bits number. 0 - 1 (0x01) 1 - 2 (0x02) 2 - 4 (0x04) 3 - 8 (0x08) 4 - 16 (0x10) 5 - 32 (0x20) 6 - 64 (0x40) 7 - 128(0x80) For example, if 802.1p priority is 0 , 4 , 7, the value is 145(1 + 16 + 128). The value 0 indicates that the priority is not set.

OBJECT-TYPE

This object indicates the ID of the local MEP. The value can be 0 or ranges from 1 to 8191. The value 0 is an invalid value.

OBJECT-TYPE

This object indicates the ID of the local MEP. The value can be 0 or ranges from 1 to 8191. The value 0 is an invalid value.

OBJECT-TYPE

This object indicates the ID of the local MEP. The value can be 0 or ranges from 1 to 8191. The value 0 is an invalid value.

OBJECT-TYPE

This object indicates the size of one-way ETH-DM packet. The value can be 0 or ranges from 64 to 1518. The value 0 means that the packet size is not specified. By default, the value is 0.

OBJECT-TYPE

This object indicates the size of a two-way ETH-DM packet. The value can be 0 or ranges from 64 to 1518. The value 0 means that the packet size is not specified. By default, the value is 0.

OBJECT-TYPE

This table is used to configure the Alarm Indication Signal (AIS) function to suppress alarms.

OBJECT-TYPE

The entry of alarm indication signal.

OBJECT-TYPE

This object indicates whether the AIS function is enabled in the current MA. The value of this object can be: enabled disabled By default, the value is disabled.

OBJECT-TYPE

This object indicates the level of the sent AIS frames. The value can be -1 or ranges from 0 to 7. The value -1 is an invalid value.

OBJECT-TYPE

This object indicates the interval of the sent AIS frames. The value can be: 1 second 60 seconds The default value is 1 second.

OBJECT-TYPE

This object indicates whether the current MA is sending AIS frames. The value can be: enabled disabled By default, the value is disabled.

OBJECT-TYPE

This object indicates whether the alarm suppression function is enabled. The value can be: enabled disabled By default, the value is disabled.

OBJECT-TYPE

This object indicates whether the alarm function on the current device is in the suppression state. The value can be: enabled disabled

OBJECT-TYPE

This table is used to configure the information about the VLAN that receives AIS frames.

OBJECT-TYPE

The entry of alarm indication signal about vlan infomation.

OBJECT-TYPE

This object indicates the ID of the PE VLAN corresponding to the AIS function.

OBJECT-TYPE

This object indicates the lower limit of the ID of the CE VLAN corresponding to the AIS function.

OBJECT-TYPE

This object indicates the upper limit of the ID of the CE VLAN corresponding to the AIS function.

OBJECT-TYPE

This object indicates the lower limit of the ID of the dot1q VLAN corresponding to the AIS function.

OBJECT-TYPE

This object indicates the upper limit of the ID of the dot1q VLAN corresponding to the AIS function.

OBJECT-TYPE

This object indicates the row status of this table. The writable columns in a row can not be changed if the row is active. All columns MUST have a valid value before a row can be activated.

OBJECT-TYPE

This table is used to enable Y.1731 to send AIS packets when the status of the interface which is monitored goes down.

OBJECT-TYPE

The entry of AIS monitoring the link status of the interface.

OBJECT-TYPE

This object indicates the index of the interface which is monitored by AIS.

OBJECT-TYPE

This object indicates the row status of this table. The writable columns in a row can not be changed if the row is active. All columns MUST have a valid value before a row can be activated.

OBJECT-TYPE

This table is used to configure the multicast MAC ping function.

OBJECT-TYPE

The entry of multicast ping.

OBJECT-TYPE

This object indicates the index of this table.

OBJECT-TYPE

This object indicates whether the multicast MAC ping function is enabled. The value can be: enabled disabled By default, the value is disabled.

OBJECT-TYPE

This object indicates the name of the MD that initiates the multicast MAC ping.

OBJECT-TYPE

This object indicates the name of the MA that initiates the multicast MAC ping.

OBJECT-TYPE

This object indicates the ID of the local MEP of the 802.1ag MAC multicast ping operation. The value ranges from 1 to 8191. By default, the value is 0.

OBJECT-TYPE

This object indicates the timeout period of the multicast MAC ping. The value ranges from 1 to 65535, in milliseconds. By default, the value is 5000.

OBJECT-TYPE

This object indicates the number of the sent multicast LBM packets. By default, the value is 3.

OBJECT-TYPE

This object indicates the priority of the sent LBM packets. The value ranges from 0 to 7 or can be 255. The value 255 is an invalid value. The greater the value is, the higher the priority is.

OBJECT-TYPE

This object indicates the number of multicast LBM packets that have been sent.

OBJECT-TYPE

This object indicates the number of multicast LBM packets that have been received.

OBJECT-TYPE

This object indicates the minimum delay after which LBR packets are received.

OBJECT-TYPE

This object indicates the maximum delay after which LBR packets are received.

OBJECT-TYPE

This object indicates the average delay after which LBR packets are received.

OBJECT-TYPE

This object indicates the row status of this table. The writable columns in a row can not be changed if the row is active. All columns MUST have a valid value before a row can be activated.

OBJECT-TYPE

This table is used to display information about the multicast LBRs for responding to the multicast MAC ping operation.

OBJECT-TYPE

The entry of multicast ping reply.

OBJECT-TYPE

This object indicates the sequence number of the multicast LBR.

OBJECT-TYPE

This object indicates the order in which multicast LBRs are received.

OBJECT-TYPE

This object indicates the MEP ID carried in the multicast LBRs. The value ranges from 0 to 8191. The value 0 is an invalid value.

OBJECT-TYPE

This object indicates the MAC address carried in the multicast LBRs.

OBJECT-TYPE

This object indicates the period from the time when the multicast LBM is sent to the time when the multicast LBR is received.

OBJECT-TYPE

This table is used to configure the information about the VLAN that receives AIS frames.

OBJECT-TYPE

The entry of alarm indication signal about vlan infomation.

OBJECT-TYPE

This object indicates the ID of the PE VLAN corresponding to the AIS function. The value 0 indicates that the PE VLAN is not set.

OBJECT-TYPE

If hwY1731AisConfigPeVlan is set to 0, the object indicates a VLAN list corresponding to the AIS function. If its value is not 0, this object indicates a CE VLAN list. The VLAN ID ranges 1 to 2047. The hwY1731AisConfigVlanListHigh value ranges 2048 to 4094.

OBJECT-TYPE

If hwY1731AisConfigPeVlan is set to 0, the object indicates a VLAN list corresponding to the AIS function. If its value is not 0, this object indicates a CE VLAN list. The VLAN ID ranges 2048 to 4094. The hwY1731AisConfigVlanListLow value ranges value 1 to 2047.

OBJECT-TYPE

This object indicates the row status of this table. The writable columns in a row can not be changed if the row is active. All columns MUST have a valid value before a row can be activated.

OBJECT-TYPE

This table defines the information about TestId.

OBJECT-TYPE

The configuration entry of TestId.

OBJECT-TYPE

This object indicates the ID of the test.

OBJECT-TYPE

This object indicates the name of the MD in which TestId is configured.

OBJECT-TYPE

This object indicates the name of the MA in which TestId is configured.

OBJECT-TYPE

This object indicates the ID of the local MEP that is specified in the TestId configuration.

OBJECT-TYPE

This object indicates whether the destination MAC address is the specified RMEP's MAC address. The default value is false.

OBJECT-TYPE

This object indicates the ID of the remote MEP that is specified in the TestId configuration.

OBJECT-TYPE

This object indicates the MAC address of the remote end.

OBJECT-TYPE

This object indicates the onward MAC address.

OBJECT-TYPE

This object indicates the backward MAC address.

OBJECT-TYPE

This object indicates whether the onward MAC address is updated automatically. The default value is false.

OBJECT-TYPE

This object indicates whether the backward MAC address is updated automatically. The default value is false.

OBJECT-TYPE

This object indicates the 802.1p priority. The value 255 is an invalid value.

OBJECT-TYPE

This object indicates the 802.1p priority of uplink packets. The value 255 is an invalid value.

OBJECT-TYPE

This object indicates the 802.1p priority of downlink packets. The value 255 is an invalid value.

OBJECT-TYPE

This object indicates the description of TestId.

OBJECT-TYPE

This object indicates whether the statistics of the testid will be recorded in testid file. The default value is false.

OBJECT-TYPE

This object indicates the queue priority. The queue priority can be (1..9).

OBJECT-TYPE

This object indicates the row status of this table. All columns MUST have a valid value before a row can be activated.

OBJECT-TYPE

This table configures the single-ended ETH-LM sending function.

OBJECT-TYPE

The configuration entry of the single-ended ETH-LM sending function.

OBJECT-TYPE

This object indicates whether single-ended ETH-LM sending is continual. If the value is 'false', it indicates that the single-ended ETH-LM is on-demand.

OBJECT-TYPE

This object indicates the interval at which LMM frames are sent. the value can be: 1 second 10 seconds 30 seconds 60 seconds

OBJECT-TYPE

This object indicates the number of the sent LMM frames. The value can be 0 or ranges from 1 to 60. In a proactive OAM scenario, the value is 0.

OBJECT-TYPE

This object indicates the row status of this table. All columns MUST have a valid value before a row can be activated.

OBJECT-TYPE

This table configures the single-ended ETH-LM receiving function.

OBJECT-TYPE

The configuration entry of the single-ended ETH-LM receiving function.

OBJECT-TYPE

This object indicates the row status of this table. All columns MUST have a valid value before a row can be activated.

OBJECT-TYPE

This table configures the one-way ETH-DM sending function.

OBJECT-TYPE

The configuration entry of the one-way ETH-DM sending function.

OBJECT-TYPE

This object indicates whether one-way ETH-DM sending is continual. If the value is 'false', it indicates that one-way ETH-DM is on-demand.

OBJECT-TYPE

This object indicates the interval at which 1DM frames are sent. the value can be: 1 second 10 seconds 30 seconds 60 seconds

OBJECT-TYPE

This object indicates the number of 1DM frames to be sent. In a proactive OAM scenario, the value is 0.

OBJECT-TYPE

This object indicates the size of a one-way ETH-DM packet. The value 0 means that the packet size is not specified. By default, the value is 0.

OBJECT-TYPE

This object indicates the row status of this table. All columns MUST have a valid value before a row can be activated.

OBJECT-TYPE

This table configures the one-way ETH-DM receiving function.

OBJECT-TYPE

The configuration entry of one-way ETH-DM receiving function.

OBJECT-TYPE

This object indicates whether one-way ETH-DM receiving is continual. If the value is 'false', it indicates that one-way ETH-DM is on-demand.

OBJECT-TYPE

This object indicates the row status of this table. All columns MUST have a valid value before a row can be activated.

OBJECT-TYPE

This table is used to configure the two-way ETH-DM sending function.

OBJECT-TYPE

The configuration entry of the two-way ETH-DM sending function.

OBJECT-TYPE

This object indicates whether two-way ETH-DM sending is continual. If the value is 'false', it indicates that two-way ETH-DM is on-demand.

OBJECT-TYPE

This object indicates the interval at which DMM frames are sent. When on-demand OAM, the value can be: 1 second 10 seconds 30 seconds 60 seconds 15 seconds

OBJECT-TYPE

This object indicates the number of DMM frames to be sent. In a proactive OAM scenario, the value is 0.

OBJECT-TYPE

This object indicates the size of two-way ETH-DM packet. The value 0 means that the packet size is not specified. By default, the value is 0.

OBJECT-TYPE

This object indicates the row status of this table. All columns MUST have a valid value before a row can be activated.

OBJECT-TYPE

This table configures the two-way ETH-DM receiving function.

OBJECT-TYPE

The configuration entry of the two-way ETH-DM receiving function.

OBJECT-TYPE

This object indicates the row status of this table. All columns MUST have a valid value before a row can be activated.

OBJECT-TYPE

This table configures the single-ended ETH-SLM sending function.

OBJECT-TYPE

The configuration entry of the single-ended ETH-SLM sending function.

OBJECT-TYPE

This object indicates whether single-ended ETH-SLM sending is continual. If the value is 'false', it indicates that the single-ended ETH-SLM is on-demand.

OBJECT-TYPE

This object indicates the interval at which single-ended ETH-SLM frames are sent. the value can be: 1 second 10 seconds 3.3 milliseconds 10 milliseconds 100 milliseconds

OBJECT-TYPE

This object indicates the number of the sent single-ended ETH-SLM frames. The value can be 0 or ranges from 1 to 1000. In a proactive OAM scenario, the value is 0.

OBJECT-TYPE

This object indicates The timeout of single-ended synthetic loss measurement frames (SLM) waiting for ACK frames (SLR). The value can be 0 or ranges from 1 to 10. In a proactive OAM scenario, the value is 0.

OBJECT-TYPE

This object indicates the row status of this table. All columns MUST have a valid value before a row can be activated.

OBJECT-TYPE

This object indicates the packetsize of single-ended synthetic loss measurement frames The value can be 0 or ranges from 64 to 1518. In a proactive OAM scenario, the value is 0.

OBJECT-TYPE

This object indicates the measurementcount of single-ended synthetic loss measurement frames The value can be 0 or ranges from 1 to 60. In a proactive OAM scenario, the value is 0.

OBJECT-TYPE

This table configures the single-ended ETH-SLM receive function.

OBJECT-TYPE

The configuration entry of the single-ended ETH-SLM receive function.

OBJECT-TYPE

This object indicates the timeout value of receive ETH-SLM frames. The value can be 0 or ranges from 10 to 300. In a proactive OAM scenario, the value is 0.

OBJECT-TYPE

This object indicates the row status of this table. All columns MUST have a valid value before a row can be activated.

OBJECT-IDENTITY

OBJECT-TYPE

This table is used to reset statistic information.

OBJECT-TYPE

The entry of reset statistic information.

OBJECT-TYPE

This object indicates the type of reset. The value can be: invalid singleloss dualloss onewaydelay twowaydelay The default value is invalid.

OBJECT-TYPE

This object indicates the priority of 802.1p which in the ResetStatistic. The priority value ranges from 0 to 7. It maps a 8 bits number. 0 - 1 (0x01) 1 - 2 (0x02) 2 - 4 (0x04) 3 - 8 (0x08) 4 - 16 (0x10) 5 - 32 (0x20) 6 - 64 (0x40) 7 - 128(0x80) For example, if 802.1p priority is 0 , 4 , 7, the value is 145(1 + 16 + 128). The value 0 indicates that the priority is not set.

OBJECT-TYPE

This table is used to store the result about Y1731 statistic information.

OBJECT-TYPE

An entry in the table, containing information on the Y1731 statistic entity.

OBJECT-TYPE

This object identifies an interval for collecting packet loss statistics.

OBJECT-TYPE

This object identifies the packet loss statistics that are collected on a local end.

OBJECT-TYPE

This object identifies the packet loss ratio that are collected on a local end.

OBJECT-TYPE

This object identifies the maximum value of packet loss ratio that are collected on a local end.

OBJECT-TYPE

This object identifies the minimum value of packet loss ratio that are collected on a local end.

OBJECT-TYPE

This object identifies the average value of packet loss ratio that are collected on a local end.

OBJECT-TYPE

This object identifies the packet loss statistics that are collected on a remote end.

OBJECT-TYPE

This object identifies the packet loss ratio that are collected on a remote end.

OBJECT-TYPE

This object identifies the maximum value of packet loss ratio that are collected on a remote end.

OBJECT-TYPE

This object identifies the minimum value of packet loss ratio that are collected on a remote end.

OBJECT-TYPE

This object identifies the average value of packet loss ratio that are collected on a remote end.

OBJECT-TYPE

This object indicates the statistics about the one-way delay.

OBJECT-TYPE

This object indicates the variation about the one-way delay. After the device is enabled to receive packets, statistics collected for the first time are invalid, and the value of hwY1731OneDelayVariation is setted to 0.

OBJECT-TYPE

This object identifies the maximum variation of the one-way delay.

OBJECT-TYPE

This object identifies the minimum variation of the one-way delay.

OBJECT-TYPE

This object identifies the average variation of the one-way delay.

OBJECT-TYPE

This object indicates the statistics about the two-way delay.

OBJECT-TYPE

This object indicates the variation about the two-way delay.

OBJECT-TYPE

This object identifies the maximum variation of the two-way delay.

OBJECT-TYPE

This object identifies the minimum variation of the two-way delay.

OBJECT-TYPE

This object identifies the average variation of the two-way delay.

OBJECT-TYPE

This object identifies the maximum value of packet loss that are collected on a local end.

OBJECT-TYPE

This object identifies the minimum value of packet loss that are collected on a local end.

OBJECT-TYPE

This object identifies the average value of packet loss that are collected on a local end.

OBJECT-TYPE

This object identifies the maximum value of packet loss that are collected on a remote end.

OBJECT-TYPE

This object identifies the minimum value of packet loss that are collected on a remote end.

OBJECT-TYPE

This object identifies the average value of packet loss that are collected on a remote end.

OBJECT-TYPE

This object identifies the maximum value of the one-way delay.

OBJECT-TYPE

This object identifies the minimum value of the one-way delay.

OBJECT-TYPE

This object identifies the average value of the one-way delay.

OBJECT-TYPE

This object identifies the maximum value of the two-way delay.

OBJECT-TYPE

This object identifies the minimum value of the two-way delay.

OBJECT-TYPE

This object identifies the average value of the two-way delay.

OBJECT-TYPE

This object identifies the number of unresponsive Delay Measurement Reply frames.

OBJECT-TYPE

This object indicates the 802.1p priority. The value 255 is an invalid value.

OBJECT-TYPE

This object indicates the 802.1p priority. The value 255 is an invalid value.

OBJECT-TYPE

This object indicates the 802.1p priority. The value 255 is an invalid value.

OBJECT-TYPE

The date and time of the one-way delay on-demand data.

OBJECT-TYPE

The date and time of the two-way delay on-demand data.

OBJECT-TYPE

The date and time of the single-loss on-demand data.

OBJECT-TYPE

This table is used to query whether the one-way delay exceeds the trap threshold in the VLAN scenario.

OBJECT-TYPE

An entry in the table, containing information on the trap entity.

OBJECT-TYPE

This object indicates the remote MAC address.

OBJECT-TYPE

This object indicates the timestamp when the delay of the one-way ETH-DM in the VLAN is higher than the configured trap threshold.

OBJECT-TYPE

This object indicates the delay value when the delay of the one-way ETH-DM in the VLAN is higher than the configured trap threshold.

OBJECT-TYPE

This object indicates the delay trap threshold of the one-way ETH-DM.

OBJECT-TYPE

This object indicates the high 32 bits delay value when the delay of the one-way ETH-DM in the VLAN is higher than the configured trap threshold.

OBJECT-TYPE

This object indicates the low 32 bits delay value when the delay of the one-way ETH-DM in the VLAN is higher than the configured trap threshold.

OBJECT-TYPE

This table is used to query whether the one-way delay falls below the trap threshold.

OBJECT-TYPE

An entry in the table, containing information on the recovery trap entity.

OBJECT-TYPE

This object indicates the remote MAC address.

OBJECT-TYPE

This object indicates the timestamp when the delay of the one-way ETH-DM in the VLAN is lower than the configured trap threshold.

OBJECT-TYPE

This object indicates the delay value when the delay of the one-way ETH-DM in the VLAN is lower than the configured trap threshold.

OBJECT-TYPE

This object indicates the delay trap threshold of the one-way ETH-DM.

OBJECT-TYPE

This object indicates the high 32 bits delay value when the delay of the one-way ETH-DM in the VLAN is lower than the configured trap threshold.

OBJECT-TYPE

This object indicates the low 32 bits delay value when the delay of the one-way ETH-DM in the VLAN is lower than the configured trap threshold.

OBJECT-TYPE

This table is used to query whether the two-way delay exceeds the trap threshold in the VLAN scenario.

OBJECT-TYPE

An entry in the table, containing information on the trap entity.

OBJECT-TYPE

This object indicates the remote MAC address.

OBJECT-TYPE

This object indicates the timestamp when the delay of the two-way ETH-DM in the VLAN is higher than the configured trap threshold.

OBJECT-TYPE

This object indicates the delay value when the delay of the two-way ETH-DM in the VLAN is higher than the configured trap threshold.

OBJECT-TYPE

This object indicates the delay trap threshold of the two-way ETH-DM.

OBJECT-TYPE

This object indicates the high 32 bits delay value when the delay of the two-way ETH-DM in the VLAN is higher than the configured trap threshold.

OBJECT-TYPE

This object indicates the low 32 bits delay value when the delay of the two-way ETH-DM in the VLAN is higher than the configured trap threshold.

OBJECT-TYPE

This table is used to query whether the two-way delay falls below the trap threshold.

OBJECT-TYPE

An entry in the table, containing information on the recovery trap entity.

OBJECT-TYPE

This object indicates the remote MAC address.

OBJECT-TYPE

This object indicates the timestamp when the delay of the two-way ETH-DM in the VLAN is lower than the configured trap threshold.

OBJECT-TYPE

This object indicates the delay value when the delay of the two-way ETH-DM in the VLAN is lower than the configured trap threshold.

OBJECT-TYPE

This object indicates the delay trap threshold for the two-way ETH-DM.

OBJECT-TYPE

This object indicates the high 32 bits delay value when the delay of the two-way ETH-DM in the VLAN is lower than the configured trap threshold.

OBJECT-TYPE

This object indicates the low 32 bits delay value when the delay of the two-way ETH-DM in the VLAN is lower than the configured trap threshold.

OBJECT-TYPE

This table is used to query whether the Y.1731 statistic value triggers alarm.

OBJECT-TYPE

An entry in the table, containing information on the statistic trap entity.

OBJECT-TYPE

Specific trap type. Options: 1. OneDelay(1) -indicates the trap type is delay of one-way ETH-DM. 2. TwoDelay(2) -indicates the trap type is delay of two-way ETH-DM. 3. OneDelayVariation(3) -indicates the trap type is delay variation of one-way ETH-DM. 4. TweDelayVariation(4) -indicates the trap type is delay variation of two-way ETH-DM. 5. SingleLossLocalRatio(5) -indicates the trap type is local loss ratio of single-ended ETH-LM. 6. SingleLossRemoteRatio(6) -indicates the trap type is remote loss ratio of single-ended ETH-LM. 7. DualLossLocalRatio(7) -indicates the trap type is local loss ratio of dual-ended ETH-LM. 8. DualLossRemoteRatio(8) -indicates the trap type is remote loss ratio of dual-ended ETH-LM.

OBJECT-TYPE

This object indicates the remote MAC address.

OBJECT-TYPE

This object indicates the priority. The value can be 255 or ranges from 0 to 7. The value 255 is an invalid value.

OBJECT-TYPE

The value that cause the trap.

OBJECT-TYPE

The upper limit value of the threshold.

OBJECT-TYPE

The lower limit value of the threshold.

OBJECT-TYPE

The value that cause the trap.

OBJECT-TYPE

The value that cause the trap.

OBJECT-TYPE

This table stores the result of single-ended ETH-LM.

OBJECT-TYPE

An entry in the table, containing information about the result of single-ended ETH-LM.

OBJECT-TYPE

This object indicates the sequence number of the single-ended ETH-LM result.

OBJECT-TYPE

This object indicates the error information of the single-ended ETH-LM result.

OBJECT-TYPE

This object identifies the packet loss statistics that are collected on a local end.

OBJECT-TYPE

This object identifies the packet loss ratio that is collected on a local end.

OBJECT-TYPE

This object identifies the packet loss statistics that are collected on a remote end.

OBJECT-TYPE

This object identifies the packet loss ratio that is collected on a remote end.

OBJECT-TYPE

The date and time of the single-loss on-demand data.

OBJECT-TYPE

This table stores the result of one-way ETH-DM.

OBJECT-TYPE

An entry in the table, containing information about the result of one-way ETH-DM.

OBJECT-TYPE

This object indicates the sequence number of the one-way ETH-DM result.

OBJECT-TYPE

This object indicates the error information about the one-way delay.

OBJECT-TYPE

This object indicates the statistics about the one-way delay.

OBJECT-TYPE

This object indicates the variation about the one-way delay. After the device is enabled to receive packets, statistics collected for the first time are invalid, and the value is set to 0.

OBJECT-TYPE

The date and time of the one-way delay on-demand data.

OBJECT-TYPE

This table stores the result of two-way ETH-DM.

OBJECT-TYPE

An entry in the table, containing information about the result of two-way ETH-DM.

OBJECT-TYPE

This object indicates the sequence number of the two-way ETH-DM result.

OBJECT-TYPE

This object indicates the error information of the two-way ETH-DM result.

OBJECT-TYPE

This object indicates the statistics about the two-way delay.

OBJECT-TYPE

This object indicates the variation about the two-way delay. After the device is enabled to receive packets, statistics collected for the first time are invalid, and the value is set to 0.

OBJECT-TYPE

The date and time of the two-way delay on-demand data.

OBJECT-TYPE

This table stores the result of two-way ETH-DM.

OBJECT-TYPE

An entry in the table, containing information about the result of two-way ETH-DM.

OBJECT-TYPE

This object indicates the type of reset. The value can be: invalid singleloss dualloss onewaydelay twowaydelay singlesynloss The default value is invalid.

OBJECT-TYPE

This table stores the statistics of two-way ETH-DM collected during the last period.

OBJECT-TYPE

An entry in the table, containing information about the statistics of two-way ETH-DM collected during the last period.

OBJECT-TYPE

This object indicates the sequence number of statistics. In order to obtain the latest set of data, you can use this node is set to 4294967295 and perform a GET operation.

OBJECT-TYPE

This object indicates the sample number of the two-way delay during the last period.

OBJECT-TYPE

This object indicates the maximum value of the two-way delay collected during the last period.

OBJECT-TYPE

This object indicates the minimum value of the two-way delay collected during the last period.

OBJECT-TYPE

This object indicates the average value of the two-way delay collected during the last period.

OBJECT-TYPE

This object indicates the num of two-way delay samples exceeded the upper limit value of the threshold during the last period.

OBJECT-TYPE

This object indicates the num of two-way delay samples fell below lower limit value of the threshold during the last period.

OBJECT-TYPE

This object indicates the sample number of the two-way delay variation during the last period.

OBJECT-TYPE

This object indicates the maximum variation of the two-way delay variation collected during the last period.

OBJECT-TYPE

This object indicates the minimum variation of the two-way delay variation collected during the last period.

OBJECT-TYPE

This object indicates the average variation of the two-way delay variation collected during the last period.

OBJECT-TYPE

This object indicates the num of two-way delay variation samples exceeded the upper limit value of the threshold during the last period.

OBJECT-TYPE

This object indicates the num of two-way delay variation samples fell below lower limit value of the threshold during the last period.

OBJECT-TYPE

This object indicates the sequence number of the current statistics.

OBJECT-TYPE

This table stores the statistics of single-ended ETH-SLM collected during the last period.

OBJECT-TYPE

An entry in the table, containing information about the statistics of single-ended ETH-SLM collected during the last period.

OBJECT-TYPE

This object indicates the sequence number of statistics. In order to obtain the latest set of data, you can use this node is set to 4294967295 and perform a GET operation.

OBJECT-TYPE

This object indicates the sample number of the single-ended ETH-SLM result during the last period.

OBJECT-TYPE

This object indicates the packet send statistics that are collected on a remote end during the last period.

OBJECT-TYPE

This object indicates the packet receive statistics that are collected on a local end during the last period.

OBJECT-TYPE

This object indicates the packet loss statistics that are collected on a local end during the last period.

OBJECT-TYPE

This object indicates the number of local loss ratio samples exceeded the upper limit value of the threshold during the last period.

OBJECT-TYPE

This object indicates the number of local loss ratio samples fell below lower limit value of the threshold during the last period.

OBJECT-TYPE

This object indicates the packet send statistics that are collected on a local end during the last period.

OBJECT-TYPE

This object indicates the packet receive statistics that are collected on a remote end during the last period.

OBJECT-TYPE

This object indicates the packet loss statistics that are collected on a remote end during the last period.

OBJECT-TYPE

This object indicates the number of remote loss ratio samples exceeded the upper limit value of the threshold during the last period.

OBJECT-TYPE

This object indicates the number of remote loss ratio samples fell below lower limit value of the threshold during the last period.

OBJECT-TYPE

This object indicates the sequence number of the current statistics.

OBJECT-TYPE

This table stores the statistics of single-ended ETH-LM collected during the last period.

OBJECT-TYPE

An entry in the table, containing information about the statistics of single-ended ETH-LM collected during the last period.

OBJECT-TYPE

This object indicates the sequence number of statistics. In order to obtain the latest set of data, you can use this node is set to 4294967295 and perform a GET operation.

OBJECT-TYPE

This object indicates the sample number of the single-ended ETH-SLM result during the last period.

OBJECT-TYPE

This object indicates the packet send statistics that are collected on a remote end during the last period.

OBJECT-TYPE

This object indicates the packet receive statistics that are collected on a local end during the last period.

OBJECT-TYPE

This object indicates the packet loss statistics that are collected on a local end during the last period.

OBJECT-TYPE

This object indicates the number of local loss ratio samples exceeded the upper limit value of the threshold during the last period.

OBJECT-TYPE

This object indicates the number of local loss ratio samples fell below lower limit value of the threshold during the last period.

OBJECT-TYPE

This object indicates the packet send statistics that are collected on a local end during the last period.

OBJECT-TYPE

This object indicates the packet receive statistics that are collected on a remote end during the last period.

OBJECT-TYPE

This object indicates the packet loss statistics that are collected on a remote end during the last period.

OBJECT-TYPE

This object indicates the number of remote loss ratio samples exceeded the upper limit value of the threshold during the last period.

OBJECT-TYPE

This object indicates the number of remote loss ratio samples fell below lower limit value of the threshold during the last period.

OBJECT-TYPE

This object indicates the sequence number of the current statistics.

OBJECT-TYPE

This table stores the statistics of single-ended ETH-LM collected during the last period with testid.

OBJECT-TYPE

An entry in the table, containing information about the statistics of single-ended ETH-LM collected during the last period with testid.

OBJECT-TYPE

This object indicates the sequence number of statistics. In order to obtain the latest set of data, you can use this node is set to 4294967295 and perform a GET operation.

OBJECT-TYPE

This object indicates the sample number of the single-ended ETH-SLM result during the last period.

OBJECT-TYPE

This object indicates the packet send statistics that are collected on a remote end during the last period.

OBJECT-TYPE

This object indicates the packet receive statistics that are collected on a local end during the last period.

OBJECT-TYPE

This object indicates the packet loss statistics that are collected on a local end during the last period.

OBJECT-TYPE

This object indicates the number of local loss ratio samples exceeded the upper limit value of the threshold during the last period.

OBJECT-TYPE

This object indicates the number of local loss ratio samples fell below lower limit value of the threshold during the last period.

OBJECT-TYPE

This object indicates the packet send statistics that are collected on a local end during the last period.

OBJECT-TYPE

This object indicates the packet receive statistics that are collected on a remote end during the last period.

OBJECT-TYPE

This object indicates the packet loss statistics that are collected on a remote end during the last period.

OBJECT-TYPE

This object indicates the number of remote loss ratio samples exceeded the upper limit value of the threshold during the last period.

OBJECT-TYPE

This object indicates the number of remote loss ratio samples fell below lower limit value of the threshold during the last period.

OBJECT-TYPE

This object indicates the sequence number of the current statistics.

OBJECT-TYPE

This table stores the result of single-ended ETH-SLM.

OBJECT-TYPE

An entry in the table, containing information about the result of single-ended ETH-SLM.

OBJECT-TYPE

This object indicates the sequence number of the single-ended ETH-SLM result.

OBJECT-TYPE

This object indicates the error information of the single-ended ETH-SLM result.

OBJECT-TYPE

This object indicates the number of local send packets about single-synthetic frame loss.

OBJECT-TYPE

This object indicates the number of remote send packets about single-synthetic frame loss.

OBJECT-TYPE

This object indicates the number of local receive packets about single-synthetic frame loss

OBJECT-TYPE

This object indicates the number of local unanswered packets about single-synthetic frame loss.

OBJECT-TYPE

This object identifies the packet loss statistics that are collected on a local end.

OBJECT-TYPE

This object identifies the packet loss ratio that is collected on a local end.

OBJECT-TYPE

This object identifies the packet loss statistics that are collected on a remote end.

OBJECT-TYPE

This object identifies the packet loss ratio that is collected on a remote end.

OBJECT-TYPE

The date and time of the single-synthetic loss on-demand data.

OBJECT-TYPE

This table is used to query whether the Y.1731 statistic value triggers alarm.

OBJECT-TYPE

An entry in the table, containing information on the statistic trap entity.

OBJECT-TYPE

Specific trap type. Options: 1. OneDelay(1) -indicates the trap type is delay of one-way ETH-DM. 2. OneDelayVariation(2) -indicates the trap type is delay variation of one-way ETH-DM. 3. TwoDelay(3) -indicates the trap type is delay of two-way ETH-DM. 4. TweDelayVariation(4) -indicates the trap type is delay variation of two-way ETH-DM. 5. SingleLossRemoteRatio(5) -indicates the trap type is remote loss ratio of single-ended ETH-LM. 6. SingleLossLocalRatio(6) -indicates the trap type is local loss ratio of single-ended ETH-LM. 7. Singlesyntheticlossremoteratio(7) -indicates the trap type is remote loss ratio of single-ended-synthetic ETH-LM. 8. Singlesyntheticlosslocalratio(8) -indicates the trap type is local loss ratio of single-ended-synthetic ETH-LM.

OBJECT-TYPE

The value that cause the trap.

OBJECT-TYPE

The upper limit value of the threshold.

OBJECT-TYPE

The lower limit value of the threshold.

OBJECT-TYPE

This object indicates the name of the cause of the trap.

OBJECT-TYPE

The MAXIMUM of AIS packets transmitted in one second.

OBJECT-TYPE

This object indicates whether the y1731 summary statistic data is managed by Performace(PM) module, If it is enabled(1), the y1731 summary statistic data is managed, saved ane sent to NMS by Performace(PM) module. The default value is disabled(2).

OBJECT-IDENTITY

OBJECT-TYPE

This object indicates the maximum value of TestId in current configuration. The value can be 0 or rangs from 1 to 4294967295. The value 0 is an invalid value.

OBJECT-TYPE

The max LCK packets transmitted or received in 1 second.

OBJECT-TYPE

The current LCK packets transmitting or receiving.

OBJECT-TYPE

The object is used to set the upper threshold value of LCK packets. The value range is from 1 to 100. The default means 80.

OBJECT-TYPE

The object is used to set the lower threshold value of LCK packets. The value range is from 1 to 100. The default means 70.