MIBs Depot

HP-SN-AGENT-MIB

Registered at
1.3.6.1.4.1.11.2.3.7.11.12.1.1.1
1.3.6.1.4.1.11.2.3.7.11.12.1.1.2
1.3.6.1.4.1.11.2.3.7.11.12.1.1.3
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1
1.3.6.1.4.1.11.2.3.7.11.12.1.2.2
1.3.6.1.4.1.11.2.3.7.11.12.1.2.3
1.3.6.1.4.1.11.2.3.7.11.12.1.2.4
1.3.6.1.4.1.11.2.3.7.11.12.1.2.5
1.3.6.1.4.1.11.2.3.7.11.12.1.2.6
1.3.6.1.4.1.11.2.3.7.11.12.1.2.7
1.3.6.1.4.1.11.2.3.7.11.12.1.2.8
1.3.6.1.4.1.11.2.3.7.11.12.1.2.9
1.3.6.1.4.1.11.2.3.7.11.12.1.2.10
1.3.6.1.4.1.11.2.3.7.11.12.1.5.1
1.3.6.1.4.1.11.2.3.7.11.12.1.5.2
Namespace
hp
Source file
HP-SN-AGENT-MIB
Digest
sha256:8fbd30745312ca0113ab33b7cb729d54e0a59a4f7bb43bf002c0908dd724cb8d

Imports

FromSymbols
HP-SN-ROOT-MIBsnAgentSys, snChassis, snStack
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP
SNMPv2-SMICounter32, Gauge32, IpAddress, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, iso
SNMPv2-TCDisplayString, TEXTUAL-CONVENTION

Imported by

1 module(s) in this corpus import this one.

Load order

Every file a consumer needs in order to load this module, dependencies first.

HP-SN-AGENT-MIB
HP-SN-ROOT-MIB
SNMPv2-CONF
SNMPv2-SMI
SNMPv2-TC

Textual conventions

NameOIDSyntaxAccessStatus
DisplayString
type
MacAddress
type

Objects

NameOIDSyntaxAccessStatus
snChasGen
OBJECT-IDENTITY
1.3.6.1.4.1.11.2.3.7.11.12.1.1.1
snChasType
OBJECT-TYPE
The chassis type represents the type of Foundry product being managed.
1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.1DisplayString (SIZE(0..128))read-onlymandatory
snChasSerNum
OBJECT-TYPE
The serial number of the chassis. If the serial number is unknown or unavailable then the value should be a zero length string.
1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.2DisplayString (SIZE(0..128))read-onlymandatory
snChasPwrSupplyStatus
OBJECT-TYPE
A bit array that contains the value of the Chassis Power Supplies. This is a packed bit string; the 2 power supplies status are encoded into 4 bits (a nibble). There are multiple power supplies per chassis in this release. The following shows the meaning of each bit: (bit 0 is the least significant bit). bit position meaning ------------ ------- 12-31 reserved 11 Power Supply 4 DC (0=bad, 1=good). 10 Power Supply 3 DC (0=bad, 1=good). 9 Power Supply 4 present status (0=present, 1=not-present). 8 Power Supply 3 present status (0=present, 1=not-present). 4-7 reserved 3 Power Supply 2 DC (0=bad, 1=good). 2 Power Supply 1 DC (0=bad, 1=good). 1 Power Supply 2 present status (0=present, 1=not-present). 0 Power Supply 1 present status (0=present, 1=not-present).
1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.3INTEGERread-onlymandatory
snChasFanStatus
OBJECT-TYPE
A bit array that contains the value of the fan status. This is a packed bit string. The status of each fan is encoded into one bit. bit value meaning --------- ------- 0 fan failure. 1 fan good. There are two fans per VLAN Switch chassis in this release. The following shows the meaning of each bit: (bit 0 is the least significant bit). bit position meaning ------------ ------- 4-31 reserved 3 fan4 status 2 fan3 status 1 fan2 status 0 fan1 status
1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.4INTEGERread-onlymandatory
snChasMainBrdDescription
OBJECT-TYPE
The main board description string. (It is obsoleted for Chassis Product)
1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.5DisplayString (SIZE(0..128))read-onlymandatory
snChasMainPortTotal
OBJECT-TYPE
The total number of ports for the main board. (It is obsoleted for Chassis Product)
1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.6INTEGER (1..24)read-onlymandatory
snChasExpBrdDescription
OBJECT-TYPE
The expansion board description string. Expansion board are those boards attaching on the main board. (It is obsoleted for Chassis Product)
1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.7DisplayString (SIZE(0..128))read-onlymandatory
snChasExpPortTotal
OBJECT-TYPE
The total number of ports for the expansion board. (It is obsoleted for Chassis Product)
1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.8INTEGER (1..24)read-onlymandatory
snChasStatusLeds
OBJECT-TYPE
A bit array that contains the value of the front panel status LEDs. This is a bit-map; each LED is encoded into 1 bit for each switch port. The maximum number of ports in one chassis is 24 that means 24 Ports Status LEDs. The expansion port number always begins from the last main port number. The following shows the meaning of each bit for each switch port: bit value meaning -------- --------- 0 off (Link off) 1 on (Link on) The bitmap of LEDs are as following: (Port1) (Port4) (Port8) Bit (Bit0) (Bit3) (Bit7) Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8 Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16 Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24 --------
1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.9INTEGERread-onlymandatory
snChasTrafficLeds
OBJECT-TYPE
A bit array that contains the value of the front panel traffic LEDs. This is a packed bit string; each LED is encoded into 1 bit for each switch port. The maximum number of ports in one chassis is 24 that means 24 Ports Traffic LEDs. The expansion port number always begins from the last main port number. The following shows the meaning of each bit for each switch port: bit value meaning -------- --------- 0 off (no traffic) 1 on (traffic) The bitmap of LEDs are as following: (Port1) (Port4) (Port8) Bit (Bit0) (Bit3) (Bit7) Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8 Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16 Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24 --------
1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.10INTEGERread-onlymandatory
snChasMediaLeds
OBJECT-TYPE
A bit array that contains the value of the front panel media LEDs. This is a packed bit string; each LED is encoded into 1 bit for each switch port. The maximum number of ports in one chassis is 24 that means 24 Ports Media LEDs. The expansion port number always begins from the last main port number. The following shows the meaning of each bit for each switch port: bit value meaning --------- ------- 0 half duplex 1 full duplex The bitmap of LEDs are as following: (Port1) (Port4) (Port8) Bit (Bit0) (Bit3) (Bit7) Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8 Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16 Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24 ---------
1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.11INTEGERread-onlymandatory
snChasEnablePwrSupplyTrap
OBJECT-TYPE
Indicates whether the SNMP agent process is permitted to generate power supply failure traps.
1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.12INTEGER {disabled(0), enabled(1)}read-writemandatory
snChasMainBrdId
OBJECT-TYPE
The main board identifier, which can uniquely identify a board type. It is an encoded octet string with the following meaning: octet 0 - octet string format version, which identifies the format of this string. If format version octet has the value 1, the octets after the version octet have the following meaning: octet 1 - product type, FIWG=0x57, FIBB=0x42, FIMLS=0x4D NI=0x4E, TI=0x54, TIRT=0x52 octet 2 - board type, POWERPC=1, ALPHA=2 The length of the octet string is 27. If format version octet has the value 2, the octets after the version octet have the following meaning: octet 1 - product type: BI_WG 0x57 BI_BB 0x42 BI_NI 0x4E octet 2 - module type: FI_MASTER_FIBER_8G 0x7 FI_MASTER_FIBER_4G 0x5 FI_MASTER_FIBER_2G 0x4 FI_SLAVE_COPPER_24 0xB MASTER_FIBER_8G 0x0 MASTER_FIBER_4G 0x1 MASTER_FIBER_2G 0x12 MASTER_FIBER_0G 0x14 MASTER_COPPER_16 0x2 MASTER_COPPER_8G 0x6 MASTER_COPPER_12_2 0x9 SLAVE_FIBER_8G 0x8 SLAVE_FIBER_4G 0x3 SLAVE_COPPER_20 0xA SLAVE_COPPER_24 0xA SLAVE_100FX_8 0xD SLAVE_100FX_16 0xC SLAVE_COPPER_8G 0xE SLAVE_COPPER_16_2 0xF STACK_FIBER_8G 0x10 STACK_COPPER_8G 0x11 SLAVE_100FX_24 0x13 The length of the octet string is 28. Both format version 1 and 2: octet 3 - processor type, PVR_M603=3, PVR_M604=4, PVR_M603E=6, PVR_M603EV=7, PVR_M604E=9 octet 4 to octet 5 - processor speed in MHz octet 6 - MAC type: MAC_SEEQ_10_100=1, MAC_DEC_10_100=2, MAC_SEEQ_1000=5, MAC_GMAC_1000=6, MAC_VLSI_1000=9 octet 7 - PHY type, PHY_NONE=0, PHY_QSI=1, PHY_ICS=3, PHY_NATIONAL=4, PHY_LEVEL1=6, PHY_LEVEL16=7, PHY_LEVEL24=8 octet 8 - port type, COPPER=0, FIBER=1 octet 9 - fiber port type, NONFIBER=0, SX_FIBER=1, LX_FIBER=2, LHX_FIBER=3, LX_SX_FIBER=4, LHB_FIBER=5 octet 10 to octet 13 - DRAM size in KBytes octet 14 to octet 17 - boot flash size in KBytes octet 18 to octet 21 - code flash size in KBytes octet 22 to octet 27 - serial number. Format version 1 only: octet 28 - chassis backplane type. chassis4000 = 0x00 chassis8000 = 0x04 Turbo8 = 0x07 (stack2) FastIron2 = 0x06 (stack1)
1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.13OCTET STRINGread-onlymandatory
snChasExpBrdId
OBJECT-TYPE
The expansion board identifier. Expansion board are those boards attaching on the main board. It is an encoded octet string with the following meaning: octet 0 - octet string format version, which identifies the format of this string. If format version octet has the value 1, the octets after the version octet have the following meaning: octet 1 - expansion board type, HUNDRED_MEG_1PORT=1, HUNDRED_MEG_2PORT=2, HUNDRED_MEG_1PORT_COPPER=3, HUNDRED_MEG_2PORT_COPPER=4, HUNDRED_MEG_2PORT_LX=5, GIGA_1PORT=8, GIGA_2PORT=9 octet 2 - fiber port type, NONFIBER=0, SX_FIBER=1, LX_FIBER=2, LHX_FIBER=3, LX_SX_FIBER=4 (It is obsoleted for Chassis Product)
1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.14OCTET STRINGread-onlymandatory
snChasSpeedLeds
OBJECT-TYPE
A bit array that contains the value of the front panel media LEDs. This is a packed bit string; each LED is encoded into 1 bit for each switch port. The maximum number of ports in one chassis is 24 that means 24 Ports Speed LEDs. The expansion port number always begins from the last main port number. The following shows the meaning of each bit for each switch port: bit value meaning --------- ------- 0 10 MBit 1 100 MBit The bitmap of LEDs are as following: (Port1) (Port4) (Port8) Bit (Bit0) (Bit3) (Bit7) Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8 Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16 Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24 ---------
1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.15INTEGERread-onlymandatory
snChasEnableFanTrap
OBJECT-TYPE
Indicates whether the SNMP agent process is permitted to generate fan failure traps.
1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.16INTEGER {disabled(0), enabled(1)}read-writemandatory
snChasIdNumber
OBJECT-TYPE
An administratively-assigned chassis identity number, used by inventory control.
1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.17DisplayString (SIZE(0..64))read-writemandatory
snChasActualTemperature
OBJECT-TYPE
Temperature of the chassis. Each unit is 0.5 degrees Celcius. Only management module built with temperature sensor hardware is applicable. For those non-applicable management module, it returns no-such-name.
1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.18INTEGER (-110..250)read-onlymandatory
snChasWarningTemperature
OBJECT-TYPE
Actual temperature higher than this threshold value will trigger the switch to send a temperature warning trap. Each unit is 0.5 degrees Celcius. Only management module built with temperature sensor hardware is applicable. For those non-applicable management module, it returns no-such-name.
1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.19INTEGER (0..250)read-writemandatory
snChasShutdownTemperature
OBJECT-TYPE
Actual temperature higher than this threshold value will shutdown a partial of the switch hardware to cool down the system. Each unit is 0.5 degrees Celcius. Only management module built with temperature sensor hardware is applicable. For those non-applicable management module, it returns no-such-name.
1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.20INTEGER (0..250)read-writemandatory
snChasEnableTempWarnTrap
OBJECT-TYPE
Indicates whether the SNMP agent process is permitted to generate temperature warning traps.
1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.21INTEGER {disabled(0), enabled(1)}read-writemandatory
snChasPwr
OBJECT-IDENTITY
1.3.6.1.4.1.11.2.3.7.11.12.1.1.2
snChasPwrSupplyTable
OBJECT-TYPE
A table of each power supply information. Only installed power supply appears in a table row.
1.3.6.1.4.1.11.2.3.7.11.12.1.1.2.1not-accessiblemandatory
snChasPwrSupplyEntry
OBJECT-TYPE
A row in the power supply table.
1.3.6.1.4.1.11.2.3.7.11.12.1.1.2.1.1not-accessiblemandatory
snChasPwrSupplyIndex
OBJECT-TYPE
The index to power supply table.
1.3.6.1.4.1.11.2.3.7.11.12.1.1.2.1.1.1INTEGERread-onlymandatory
snChasPwrSupplyDescription
OBJECT-TYPE
The power supply description string.
1.3.6.1.4.1.11.2.3.7.11.12.1.1.2.1.1.2DisplayString (SIZE(0..128))read-onlymandatory
snChasPwrSupplyOperStatus
OBJECT-TYPE
The power supply operation status.
1.3.6.1.4.1.11.2.3.7.11.12.1.1.2.1.1.3INTEGER {other(1), normal(2), failure(3)}read-onlymandatory
snChasFan
OBJECT-IDENTITY
1.3.6.1.4.1.11.2.3.7.11.12.1.1.3
snChasFanTable
OBJECT-TYPE
A table of each fan information. Only installed fan appears in a table row.
1.3.6.1.4.1.11.2.3.7.11.12.1.1.3.1not-accessiblemandatory
snChasFanEntry
OBJECT-TYPE
A row in the fan table.
1.3.6.1.4.1.11.2.3.7.11.12.1.1.3.1.1not-accessiblemandatory
snChasFanIndex
OBJECT-TYPE
The index to fan table.
1.3.6.1.4.1.11.2.3.7.11.12.1.1.3.1.1.1INTEGERread-onlymandatory
snChasFanDescription
OBJECT-TYPE
The fan description string.
1.3.6.1.4.1.11.2.3.7.11.12.1.1.3.1.1.2DisplayString (SIZE(0..128))read-onlymandatory
snChasFanOperStatus
OBJECT-TYPE
The fan operation status.
1.3.6.1.4.1.11.2.3.7.11.12.1.1.3.1.1.3INTEGER {other(1), normal(2), failure(3)}read-onlymandatory
snAgentGbl
OBJECT-IDENTITY
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1
snAgReload
OBJECT-TYPE
Action object to reboot the agent. The following values can only be read: other(1).....agent in unknown or other state running(2)...agent running The following value can be written: reset(3).....do a hard reset The agent will return a response before the action occurs.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.1INTEGER {other(1), running(2), reset(3)}read-writemandatory
snAgEraseNVRAM
OBJECT-TYPE
Action object to erase NVRAM of the agent. The following values can only be read: normal(1) error(2)... operation failed or bad flash erasing(4)...agent is erasing NVRAM flash The following value can be written: erase(3).....do erase The agent will return a response even before the erase is done. And the read value will be erasing until erase is done. And the erase request will be rejected until error or normal.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.2INTEGER {normal(1), error(2), erase(3), erasing(4)}read-writemandatory
snAgWriteNVRAM
OBJECT-TYPE
Action object to save all configuration info to NVRAM of the agent. The following values can only be read: normal(1) error(2)... operation failed or bad flash writing(4)...agent is writing NVRAM flash The following value can be written: write(3).....do write The agent will return a response even before the write is done. And the read value will be writing until write is done. And the write request will be rejected until error or normal.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.3INTEGER {normal(1), error(2), write(3), writing(4)}read-writemandatory
snAgConfigFromNVRAM
OBJECT-TYPE
Action object to config the switch from NVRAM of the agent. The following values can only be read: normal(1) error(2)... operation failed or bad flash configing(4)...configing from NVRAM flash is in process. The following value can be written: config(3).....do config The agent will return a response after config is done.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.4INTEGER {normal(1), error(2), config(3), configing(4)}not-accessiblemandatory
snAgTftpServerIp
OBJECT-TYPE
The tftp server address, this will be used for both download/upload image file and config file.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.5IpAddressread-writemandatory
snAgImgFname
OBJECT-TYPE
Name of the image file including path currently associated with the system. When the object is not used, the value is a zero length string.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.6DisplayString (SIZE(0..32))read-writemandatory
snAgImgLoad
OBJECT-TYPE
Action object to down/up load a new image to the agent. The following values: Error values: from normal(1) to operationError(17) and tftpWrongFileType(23). loading(18) .. operation is in process. The following values are used for set : uploadPrimary(19)..upload the Primary image from flash to tftp server. downloadPrimary(20)..download the Primary image from tftp server to flash. uploadSecondary(21)..upload the Secondary image from flash to tftp server. downloadSecondary(22)..download the Secondary image from tftp server to flash. The image filename is defined in snAgImgFname. The tftp server address is defined in snAgTftpServerIp. Atomic set of snAgImgLoad, snAgImgFname and snAgTftpServerIp is required to allow down/up load to happen. And the write request will be rejected during loading until error or normal.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.7INTEGER {normal(1), flashPrepareReadFailure(2), flashReadError(3), flashPrepareWriteFailure(4), flashWriteError(5), tftpTimeoutError(6), tftpOutOfBufferSpace(7), tftpBusy(8), tftpRemoteOtherErrors(9), tftpRemoteNoFile(10), tftpRemoteBadAccess(11), tftpRemoteDiskFull(12), tftpRemoteBadOperation(13), tftpRemoteBadId(14), tftpRemoteFileExists(15), tftpRemoteNoUser(16), operationError(17), loading(18), uploadPrimary(19), downloadPrimary(20), uploadSecondary(21), downloadSecondary(22), tftpWrongFileType(23)}read-writemandatory
snAgCfgFname
OBJECT-TYPE
Name of the config file(s) including path currently associated with the system. Some agents in special situations may support a value which contains multiple file names instead of a single file name. Multiple names are specified as a list of file names separated by semicolons (;). When the object is not used, the value is a zero length string.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.8DisplayString (SIZE(0..32))read-writemandatory
snAgCfgLoad
OBJECT-TYPE
Action object to down/up load a config image to the agent. The following values can be read : Error values: from normal(1) to operationError(17) and tftpWrongFileType(29). loading(18) .. operation is in process. The following value can be used to set: uploadFromFlashToServer(20)..upload the config from flash to tftp server. downloadToFlashFromServer(21)..download the config to flash from tftp server. uploadFromDramToServer(22)..upload the config from DRAM to tftp server. downloadToDramFromServer(23)..download the config to DRAM from tftp server. The following value can be used to set: uploadFromFlashToNMS(24)..upload the config from flash to NMS. downloadToFlashFromNMS(25)..download the config to flash from NMS. uploadFromDramToNMS(26)..upload the config from DRAM to NMS. downloadToDramFromNMS(27)..download the config to DRAM from NMS. The config filename is defined in snAgCfgFname. The tftp server address is defined in snAgTftpServerIp. Atomic set of snAgCfgLoad, snAgCfgFname and snAgTftpServerIp is required to allow down/up load to happen. And the write request will be rejected during loading until error or normal. For those NMS commands from (24) to (27), The snAgCfgEosTable MIB must be sent along in one PDU. A seperate write memory cli or set snAgWriteNVRAM is required to save the config to NVRAM.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.9INTEGER {normal(1), flashPrepareReadFailure(2), flashReadError(3), flashPrepareWriteFailure(4), flashWriteError(5), tftpTimeoutError(6), tftpOutOfBufferSpace(7), tftpBusy(8), tftpRemoteOtherErrors(9), tftpRemoteNoFile(10), tftpRemoteBadAccess(11), tftpRemoteDiskFull(12), tftpRemoteBadOperation(13), tftpRemoteBadId(14), tftpRemoteFileExists(15), tftpRemoteNoUser(16), operationError(17), loading(18), uploadFromFlashToServer(20), downloadToFlashFromServer(21), uploadFromDramToServer(22), downloadToDramFromServer(23), uploadFromFlashToNMS(24), downloadToFlashFromNMS(25), uploadFromDramToNMS(26), downloadToDramFromNMS(27), operationDoneWithNMS(28), tftpWrongFileType(29)}read-writemandatory
snAgDefGwayIp
OBJECT-TYPE
The default gateway (router) address.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.10IpAddressread-writemandatory
snAgImgVer
OBJECT-TYPE
The version of the running software in the form 'major.minor.maintenance[letters]'.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.11DisplayString (SIZE(0..32))read-onlymandatory
snAgFlashImgVer
OBJECT-TYPE
The version of the software image saved in local storage such as flash memory in the form 'major.minor.maintenance[letters]'. If not known or not available, then the value is a zero length string.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.12DisplayString (SIZE(0..32))read-onlymandatory
snAgGblIfIpAddr
OBJECT-TYPE
The interface ip address.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.13IpAddressread-writemandatory
snAgGblIfIpMask
OBJECT-TYPE
The interface ip address mask.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.14IpAddressread-writemandatory
snAgGblPassword
OBJECT-TYPE
System Security Access Password and this is only allowed to use for setting but not for reading. An SNMP-Get will get an zero string.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.15DisplayString (SIZE(0..48))read-writemandatory
snAgTrpRcvrCurEntry
OBJECT-TYPE
The current total entries of the Trap Receiver Table are created.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.16INTEGER (0..255)read-onlymandatory
snAgGblDataRetrieveMode
OBJECT-TYPE
By default, this mode is set to nextbootCfg(0). The VLAN Table and Port-STP Table data will be retrieved according to this mode. nextbootCfg(0).........the nextboot configuration data are retrieved operationalData(1)..........the current running data are retrieved
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.19INTEGER {nextbootCfg(0), operationalData(1)}read-writemandatory
snAgSystemLog
OBJECT-TYPE
The system log object to indicate whether any Network Management Station(NMS) has login. The first byte of the octet string is the value decribed below and followed by 4 bytes of secret code. login(1)..... a value for a NMS to login. heartbeat(2)... a value for the login NMS periodically to checkin; Otherwise, the Agent will automatically set this object to logout(3) after a timeout period. logout(3).... a value for a NMS to logout. changePassword(4).... a value for the login NMS to change password, only if snAgGblPasswordChangeMode was configured to 'anyMgmtEntity'. changeReadOnlyCommunity(5).... a value for the login NMS to change the read-only community string, only if snAgGblPasswordChangeMode was configured to 'anyMgmtEntity'. changeReadWriteCommunity(6).... a value for the login NMS to change the read-write community string, only if snAgGblPasswordChangeMode was configured to 'anyMgmtEntity'.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.20OCTET STRING (SIZE(5))read-writemandatory
snAgGblEnableColdStartTrap
OBJECT-TYPE
Indicates whether the SNMP agent process is permitted to generate cold start traps.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.21INTEGER {disabled(0), enabled(1)}read-writemandatory
snAgGblEnableLinkUpTrap
OBJECT-TYPE
Indicates whether the SNMP agent process is permitted to generate link up traps.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.22INTEGER {disabled(0), enabled(1)}read-writemandatory
snAgGblEnableLinkDownTrap
OBJECT-TYPE
Indicates whether the SNMP agent process is permitted to generate link down traps.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.23INTEGER {disabled(0), enabled(1)}read-writemandatory
snAgGblPasswordChangeMode
OBJECT-TYPE
Specify which management entity is allowed to change the password. 'anyMgmtEntity' management entities are SNMP management station, console command line interface, and telnet command line interface. For security reason, this object can only be modified by console command line interface or telnet command line interface. The default value is 'consoleAndTelnet', of which both console and telnet command line interfaces are allowed to change the password.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.24INTEGER {anyMgmtEntity(1), consoleAndTelnet(2), consoleOnly(3), telnetOnly(4)}read-onlymandatory
snAgGblReadOnlyCommunity
OBJECT-TYPE
SNMP read community string and this is only allowed to use for setting but not for reading. An SNMP-Get will get an zero length string.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.25DisplayString (SIZE(0..32))read-writemandatory
snAgGblReadWriteCommunity
OBJECT-TYPE
SNMP read-write community string and this is only allowed to use for setting but not for reading. An SNMP-Get will get an zero length string.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.26DisplayString (SIZE(0..32))read-writemandatory
snAgGblCurrentSecurityLevel
OBJECT-TYPE
This represnts the current log-in security level. Each level of security requires a password to permit user for different system configurations.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.27INTEGER (0..5)read-onlymandatory
snAgGblSecurityLevelSet
OBJECT-TYPE
This shows which the security level password to be set.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.28INTEGER (0..5)read-writemandatory
snAgGblLevelPasswordsMask
OBJECT-TYPE
This shows the bitmap of level passwords which successfully assigned to the system.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.29INTEGERread-onlymandatory
snAgGblQueueOverflow
OBJECT-TYPE
false - The device queues are not overflow. true - The device queues are overflow.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.30INTEGER {false(0), true(1)}read-onlymandatory
snAgGblBufferShortage
OBJECT-TYPE
false - The device buffers are adequate. true - The device buffers are in shortage.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.31INTEGER {false(0), true(1)}read-onlymandatory
snAgGblDmaFailure
OBJECT-TYPE
false - The device DMAs are in good condition. true - One of the DMAs in the device fails.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.32INTEGER {false(0), true(1)}read-onlymandatory
snAgGblResourceLowWarning
OBJECT-TYPE
false - No, the device does not have resource-low-warning. true - Yes, the device does have resource-low-warning.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.33INTEGER {false(0), true(1)}read-onlymandatory
snAgGblExcessiveErrorWarning
OBJECT-TYPE
false - No, the device does not have any excessive collision, FCS errors, alignment warning etc. true - Yes, the device does have.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.34INTEGER {false(0), true(1)}read-onlymandatory
snAgGblCpuUtilData
OBJECT-TYPE
The statistics collection of utilization of the CPU in the device.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.35Gaugeread-onlymandatory
snAgGblCpuUtilCollect
OBJECT-TYPE
enable(1) - The beginning of statistics collection of utilization of the CPU in the device. disable(0) - The end of statistics collection of utilization of the CPU in the device.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.36INTEGER {disabled(0), enabled(1)}read-writemandatory
snAgGblTelnetTimeout
OBJECT-TYPE
Telnet session idling timeout value. Writing value 0 to this object never timeouts any telnet sessions. Each value unit is one minute.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.37INTEGER (0..240)read-writemandatory
snAgGblEnableWebMgmt
OBJECT-TYPE
Enable/disable web management.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.38INTEGER {disabled(0), enabled(1)}read-writemandatory
snAgGblSecurityLevelBinding
OBJECT-TYPE
This represnts the binding of a given password to which security level. A value of 255 indicates an invalid binding.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.39INTEGERread-onlymandatory
snAgGblEnableSLB
OBJECT-TYPE
Enable/disable Server Load Balancing.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.40INTEGER {disabled(0), enabled(1)}read-onlymandatory
snAgSoftwareFeature
OBJECT-TYPE
A bit string representing the software feature of the running switch/router image. These features were conditional compiled to different product images. For each bit, exist feature has a value of 1, but non-exist feature has a value of 0. octet 0, bit 0 - RMON octet 0, bit 1 - ipx switching octet 0, bit 2 - server load balancing octet 0, bit 3 - layer 3 filter in switch octet 0, bit 4 - ipx routing octet 0, bit 5 - appletalk routing octet 0, bit 6 - ip multicast routing octet 0, bit 7 - local access control octet 1, bit 0 - BGP routing octet 1, bit 1 - loopback interface octet 1, bit 2 - BigIron multi-management module octet 1, bit 3 - BigIron SYSIF II octet 1, bit 4 - BigIron POS support octet 1, bit 5 - appletalk cable vlan octet 1, bit 6 - 64 subnet octet 1, bit 7 - multi-slot trunk octet 2, bit 0 - TACACS octet 2, bit 1 - Gigabit Ethernet port auto-negotiation mode octet 2, bit 2 - FSRP octet 2, bit 3 - Exodus requested OSPF enhancement octet 2, bit 4 - OSPF NSSA octet 2, bit 5 - POS octet 2, bit 6 - QOS octet 2, bit 7 - Single Span octet 3, bit 0 - Fast Span octet 3, bit 1 - Base L3 octet 3, bit 2 - static log buffer Bit 0 is the least significant bit of an octet, and bit 7 is the most significant bit of an octet.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.41OCTET STRINGread-onlymandatory
snAgGblEnableModuleInsertedTrap
OBJECT-TYPE
Indicates whether the SNMP agent process is permitted to generate hardware module inserted to chassis traps.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.42INTEGER {disabled(0), enabled(1)}read-writemandatory
snAgGblEnableModuleRemovedTrap
OBJECT-TYPE
Indicates whether the SNMP agent process is permitted to generate hardware module removed from chassis traps.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.43INTEGER {disabled(0), enabled(1)}read-writemandatory
snAgGblTrapMessage
OBJECT-TYPE
A generic trap message string.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.44DisplayStringread-onlymandatory
snAgGblEnableTelnetServer
OBJECT-TYPE
Enable or disable telnet server in device.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.45INTEGER {disabled(0), enabled(1)}read-writemandatory
snAgGblTelnetPassword
OBJECT-TYPE
Telnet Access Password and this is only allowed to use for setting but not for reading. An SNMP-Get will get an zero string.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.46DisplayString (SIZE(0..48))read-writemandatory
snAgBuildDate
OBJECT-TYPE
The date of the built software.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.47DisplayString (SIZE(0..32))read-onlymandatory
snAgBuildtime
OBJECT-TYPE
The time of the built software.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.48DisplayString (SIZE(0..32))read-onlymandatory
snAgBuildVer
OBJECT-TYPE
The version of the built software in the form 'major.minor.maintenance[letters]'.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.49DisplayString (SIZE(0..32))read-onlymandatory
snAgentBrd
OBJECT-IDENTITY
1.3.6.1.4.1.11.2.3.7.11.12.1.2.2
snAgentBrdTable
OBJECT-TYPE
A table of each physical board information.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1not-accessiblemandatory
snAgentBrdEntry
OBJECT-TYPE
A row in the Agent Board table.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1not-accessiblemandatory
snAgentBrdIndex
OBJECT-TYPE
The index to the Agent Interface Table.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.1INTEGER (1..8)read-onlymandatory
snAgentBrdMainBrdDescription
OBJECT-TYPE
The main board description string.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.2DisplayString (SIZE(0..128))read-onlymandatory
snAgentBrdMainBrdId
OBJECT-TYPE
The main board identifier, which can uniquely identify a board type. It is an encoded octet string with the following meaning: octet 0 - octet string format version, which identifies the format of this string. If format version octet has the value 2, the octets after the version octet have the following meaning: octet 1 - product type: BI_WG 0x57 BI_BB 0x42 BI_NI 0x4E octet 2 - module type: MASTER_FIBER_8G 0x0 MASTER_FIBER_4G 0x1 MASTER_FIBER_2G 0x12 MASTER_FIBER_0G 0x14 MASTER_COPPER_16 0x2 MASTER_COPPER_8G 0x6 MASTER_COPPER_12_2 0x9 SLAVE_FIBER_8G 0x8 SLAVE_FIBER_4G 0x3 SLAVE_FIBER_2G 0x17 SLAVE_COPPER_8G 0xE SLAVE_COPPER_2G 0x18 SLAVE_COPPER_16_2 0xF SLAVE_COPPER_20 0xA SLAVE_COPPER_24 0xA SLAVE_100FX_8 0xD SLAVE_100FX_16 0xC SLAVE_100FX_24 0x13 STACK_FIBER_8G 0x10 STACK_COPPER_8G 0x11 POS_622M 0x15 POS_155M 0x16 octet 3 - processor type, PVR_M603=3, PVR_M604=4, PVR_M603E=6, PVR_M603EV=7, PVR_M604E=9 octet 4 to octet 5 - processor speed in MHz octet 6 - MAC type: MAC_SEEQ_10_100=1, MAC_DEC_10_100=2, MAC_SEEQ_1000=5, MAC_GMAC_1000=6, MAC_VLSI_1000=9 octet 7 - PHY type, PHY_NONE=0, PHY_QSI=1, PHY_ICS=3, PHY_NATIONAL=4, PHY_LEVEL1=6, PHY_LEVEL16=7, PHY_LEVEL24=8 octet 8 - port type, COPPER=0, FIBER=1 octet 9 - fiber port type, NONFIBER=0, SX_FIBER=1, LX_FIBER=2, LHX_FIBER=3 octet 10 to octet 13 - DRAM size in KBytes octet 14 to octet 17 - boot flash size in KBytes octet 18 to octet 21 - code flash size in KBytes octet 22 to octet 27 - serial number. octet 28 - chassis backplane type. chassis4000 = 0x00 chassis8000 = 0x04 Turbo8 = 0x07 (stack2) FastIron2 = 0x06 (stack1)
1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.3OCTET STRINGread-onlymandatory
snAgentBrdMainPortTotal
OBJECT-TYPE
The total number of ports for the main board.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.4INTEGER (1..32)read-onlymandatory
snAgentBrdExpBrdDescription
OBJECT-TYPE
The expansion board description string. Expansion board are those boards attaching on the main board.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.5DisplayString (SIZE(0..128))read-onlymandatory
snAgentBrdExpBrdId
OBJECT-TYPE
The expansion board identifier. Expansion board are those boards attaching on the main board. It is an encoded octet string with the following meaning: octet 0 - octet string format version, which identifies the format of this string. If format version octet has the value 1, the octets after the version octet have the following meaning: octet 1 - expansion board type, HUNDRED_MEG_1PORT=1, HUNDRED_MEG_2PORT=2, HUNDRED_MEG_1PORT_COPPER=3, HUNDRED_MEG_2PORT_COPPER=4, HUNDRED_MEG_2PORT_LX=5, GIGA_1PORT=8, GIGA_2PORT=9 octet 2 - fiber port type, NONFIBER=0, SX_FIBER=1, LX_FIBER=2, LHX_FIBER=3, LX_SX_FIBER=4
1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.6OCTET STRINGread-onlymandatory
snAgentBrdExpPortTotal
OBJECT-TYPE
The total number of ports for the expansion board.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.7INTEGER (1..24)read-onlymandatory
snAgentBrdStatusLeds
OBJECT-TYPE
A bit array that contains the value of the front panel status LEDs. This is a bit-map; each LED is encoded into 1 bit for each switch port. The maximum number of ports in one chassis is 32 that means 32 Ports Status LEDs. The expansion port number always begins from the last main port number. The following shows the meaning of each bit for each switch port: bit value meaning -------- --------- 0 off (Link off) 1 on (Link on) The bitmap of LEDs are as following: (Port1) (Port4) (Port8) Bit (Bit0) (Bit3) (Bit7) Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8 Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16 Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24 --------
1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.8INTEGERread-onlymandatory
snAgentBrdTrafficLeds
OBJECT-TYPE
A bit array that contains the value of the front panel traffic LEDs. This is a packed bit string; each LED is encoded into 1 bit for each switch port. The maximum number of ports in one chassis is 24 that means 24 Ports Traffic LEDs. The expansion port number always begins from the last main port number. The following shows the meaning of each bit for each switch port: bit value meaning -------- --------- 0 off (no traffic) 1 on (traffic) The bitmap of LEDs are as following: (Port1) (Port4) (Port8) Bit (Bit0) (Bit3) (Bit7) Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8 Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16 Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24 --------
1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.9INTEGERread-onlymandatory
snAgentBrdMediaLeds
OBJECT-TYPE
A bit array that contains the value of the front panel media LEDs. This is a packed bit string; each LED is encoded into 1 bit for each switch port. The maximum number of ports in one chassis is 24 that means 24 Ports Media LEDs. The expansion port number always begins from the last main port number. The following shows the meaning of each bit for each switch port: bit value meaning --------- ------- 0 half duplex 1 full duplex The bitmap of LEDs are as following: (Port1) (Port4) (Port8) Bit (Bit0) (Bit3) (Bit7) Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8 Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16 Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24 ---------
1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.10INTEGERread-onlymandatory
snAgentBrdSpeedLeds
OBJECT-TYPE
A bit array that contains the value of the front panel media LEDs. This is a packed bit string; each LED is encoded into 1 bit for each switch port. The maximum number of ports in one chassis is 24 that means 24 Ports Speed LEDs. The expansion port number always begins from the last main port number. The following shows the meaning of each bit for each switch port: bit value meaning --------- ------- 0 10 MBit 1 100 MBit The bitmap of LEDs are as following: (Port1) (Port4) (Port8) Bit (Bit0) (Bit3) (Bit7) Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8 Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16 Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24 ---------
1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.11INTEGERread-onlymandatory
snAgentBrdModuleStatus
OBJECT-TYPE
By default, this mode is set to notActivated(0). moduleEmpty(0) ......... The slot of the chassis is empty. moduleGoingDown(2) ..... The module is going down. moduleRejected(3) ...... The module is being rejected due to wrong configuration. moduleBad(4) ........... The module Hardware is bad. moduleComingUp(9) ...... The module is in power-up cycle. moduleRunning(10) ....... The module is running.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.12INTEGER {moduleEmpty(0), moduleGoingDown(2), moduleRejected(3), moduleBad(4), moduleComingUp(9), moduleRunning(10)}read-onlymandatory
snAgentBrdRedundantStatus
OBJECT-TYPE
The redundant status of a module. Non-management module always returns other(1). Management module returns the rest of the states.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.13INTEGER {other(1), active(2), standby(3), crashed(4), comingUp(5)}read-onlymandatory
snAgentBrdAlarmLeds
OBJECT-TYPE
A bit array that contains the value of the front panel media LEDs (for POS Module Only). This is a packed bit string; each LED is encoded into 1 bit for each switch port. The maximum number of ports in one chassis is 24 that means 24 Ports Speed LEDs. The expansion port number always begins from the last main port number. The following shows the meaning of each bit for each switch port: bit value meaning --------- ------- 0 no alarm 1 alarm The bitmap of LEDs are as following: (Port1) (Port4) (Port8) Bit (Bit0) (Bit3) (Bit7) Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8 Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16 Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24 ---------
1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.14INTEGERread-onlymandatory
snAgentBrdTxTrafficLeds
OBJECT-TYPE
A bit array that contains the value of the front panel transmit traffic LEDs (for POS Module Only). This is a packed bit string; each LED is encoded into 1 bit for each switch port. The maximum number of ports in one chassis is 24 that means 24 Ports Transmit Traffic LEDs. The expansion port number always begins from the last main port number. The following shows the meaning of each bit for each switch port: bit value meaning -------- --------- 0 off (no transmit traffic) 1 on (transmit traffic) The bitmap of LEDs are as following: (Port1) (Port4) (Port8) Bit (Bit0) (Bit3) (Bit7) Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8 Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16 Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24 --------
1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.15INTEGERread-onlymandatory
snAgentBrdRxTrafficLeds
OBJECT-TYPE
A bit array that contains the value of the front panel receive traffic LEDs (for POS Module Only). This is a packed bit string; each LED is encoded into 1 bit for each switch port. The maximum number of ports in one chassis is 24 that means 24 Ports Receive Traffic LEDs. The expansion port number always begins from the last main port number. The following shows the meaning of each bit for each switch port: bit value meaning -------- --------- 0 off (no receive traffic) 1 on (receive traffic) The bitmap of LEDs are as following: (Port1) (Port4) (Port8) Bit (Bit0) (Bit3) (Bit7) Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8 Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16 Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24 --------
1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.16INTEGERread-onlymandatory
snAgentTrp
OBJECT-IDENTITY
1.3.6.1.4.1.11.2.3.7.11.12.1.2.3
snAgTrpRcvrTable
OBJECT-TYPE
A table of managers which to send traps.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.3.1not-accessiblemandatory
snAgTrpRcvrEntry
OBJECT-TYPE
A row in the trap receiver table. The column snAgTrpRcvrStatus is used to create and delete rows in the table. Creation requires a SET PDU with objects snAgTrpRcvrIndex, snAgTrpRcvrIpAddr, snAgTrpRcvrComm and snAgTrpRcvrStatus.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.3.1.1not-accessiblemandatory
snAgTrpRcvrIndex
OBJECT-TYPE
The index to the Trap Receiver Table.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.3.1.1.1INTEGER (1..10)read-onlymandatory
snAgTrpRcvrIpAddr
OBJECT-TYPE
The ip address for SNMP manager that is to receive the trap.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.3.1.1.2IpAddressread-writemandatory
snAgTrpRcvrComm
OBJECT-TYPE
Community string to use.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.3.1.1.3OCTET STRING (SIZE(0..32))read-writemandatory
snAgTrpRcvrStatus
OBJECT-TYPE
This object is used to create and delete rows in the table and control if they are used. The values that can be written are: ignore(5)...don't use this entry to send traps to at this time delete(3)...deletes the row create(4)...creates a new row If the row exists, then a SET with value of create(5) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: other(1)....some other case valid(2)....the row exists and is valid ignore(5)...don't use this entry to send traps to at this time
1.3.6.1.4.1.11.2.3.7.11.12.1.2.3.1.1.4INTEGER {other(1), valid(2), delete(3), create(4), ignore(5)}read-writemandatory
snAgentBoot
OBJECT-IDENTITY
1.3.6.1.4.1.11.2.3.7.11.12.1.2.4
snAgBootSeqTable
OBJECT-TYPE
A table of image load sequnce instructions to the boot code. Boot code will start from instruction of the first valid entry to load the image. If failed, it will use the second valid entry and so on, until a succesful load has completed. Each entry must have an unique instruction, duplicate instructions will be rejected.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.4.1not-accessiblemandatory
snAgBootSeqEntry
OBJECT-TYPE
A row in the boot sequence table.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.4.1.1not-accessiblemandatory
snAgBootSeqIndex
OBJECT-TYPE
The index to the boot sequence table.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.4.1.1.1INTEGER (1..4)read-onlymandatory
snAgBootSeqInstruction
OBJECT-TYPE
The instruction for the boot code.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.4.1.1.2INTEGER {fromPrimaryFlash(1), fromSecondaryFlash(2), fromTftpServer(3), fromBootpServer(4)}read-writemandatory
snAgBootSeqIpAddr
OBJECT-TYPE
The ip address of the TFTP server if snAgBootSeqInstruction was set to 'fromTftpServer'; otherwise, this object is not used in any other boot instruction.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.4.1.1.3IpAddressread-writemandatory
snAgBootSeqFilename
OBJECT-TYPE
The image filename on the TFTP server if snAgBootSeqInstruction was set to 'fromTftpServer'; otherwise, this object is not used in any other boot instruction.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.4.1.1.4DisplayString (SIZE(0..32))read-writemandatory
snAgBootSeqRowStatus
OBJECT-TYPE
To create or delete a boot sequence table entry.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.4.1.1.5INTEGER {other(1), valid(2), delete(3), create(4)}read-writemandatory
snAgCfgEos
OBJECT-IDENTITY
1.3.6.1.4.1.11.2.3.7.11.12.1.2.5
snAgCfgEosTable
OBJECT-TYPE
This table represents the fragmented Configuration File data packet with checksum include in each rows of this table. A SNMP-SET represents configuration file download, and a SNMP-GET represents configuration file upload. This action is only if the SNMP-SET of snAgCfgLoad command is sent along with this table consecutively. The applicable snAgCfgLoad command value is as followings: uploadFromFlashToNMS(23), downloadToFlashFromNMS(24), uploadFromDramToNMS(25), downloadToDramFromNMS(26).
1.3.6.1.4.1.11.2.3.7.11.12.1.2.5.1not-accessiblemandatory
snAgCfgEosEntry
OBJECT-TYPE
An EOS row in the table of encoded octet strings for table snAgCfgEosTable.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.5.1.1not-accessiblemandatory
snAgCfgEosIndex
OBJECT-TYPE
Each VLAN EOS Buffer Identifier have a multiple VLAN table entries.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.5.1.1.1INTEGERread-onlymandatory
snAgCfgEosPacket
OBJECT-TYPE
An encoded octet string. On reads it contains an integral number of configuration file data packets. The size of each encoded octet string is less than or equal to 1400 bytes.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.5.1.1.2OCTET STRING (SIZE(0..1000))read-writemandatory
snAgCfgEosChkSum
OBJECT-TYPE
A checksum of each configuration file data packet.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.5.1.1.3INTEGERread-writemandatory
snAgentLog
OBJECT-IDENTITY
1.3.6.1.4.1.11.2.3.7.11.12.1.2.6
snAgSysLogGbl
OBJECT-IDENTITY
1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.1
snAgSysLogGblEnable
OBJECT-TYPE
Enable/disable system logging.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.1.1INTEGER {disabled(0), enabled(1)}read-writemandatory
snAgSysLogGblBufferSize
OBJECT-TYPE
The number of dynamic system logging entries.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.1.2INTEGER (1..100)read-writemandatory
snAgSysLogGblClear
OBJECT-TYPE
Clear dynamic and/or static system logging buffers.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.1.3INTEGER {normal(0), clearAll(1), clearDynamic(2), clearStatic(3)}read-writemandatory
snAgSysLogGblCriticalLevel
OBJECT-TYPE
Filter events going to the logging buffer. This is a packed bit string object of which each bit has the following meaning: (bit 0 is the least significant bit). bit position meaning ------------ ------- 8-31 reserved 7 Warning (warning conditions) 6 Notification (normal but significant conditions) 5 Informational (informational messages) 4 Error (error conditions) 3 Emergency (system is unusable) 2 Debugging (debugging messages) 1 Critical (critical conditions) 0 Alert (immediate action needed) Setting a critical level bit to 1 makes the logging buffer accept the corresponding event. Resetting a critical level bit to 0 makes the logging buffer reject the corresponding event.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.1.4INTEGERread-writemandatory
snAgSysLogGblLoggedCount
OBJECT-TYPE
The number events logged in the system logging buffer.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.1.5Counterread-onlymandatory
snAgSysLogGblDroppedCount
OBJECT-TYPE
The number of events dropped.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.1.6Counterread-onlymandatory
snAgSysLogGblFlushedCount
OBJECT-TYPE
The number of times that the system logging buffer was cleared.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.1.7Counterread-onlymandatory
snAgSysLogGblOverrunCount
OBJECT-TYPE
The number of times that the system logging buffer was wrapped around.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.1.8Counterread-onlymandatory
snAgSysLogGblServer
OBJECT-TYPE
IP address of syslog server.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.1.9IpAddressread-writemandatory
snAgSysLogGblFacility
OBJECT-TYPE
Facility code.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.1.10INTEGER {kern(1), user(2), mail(3), daemon(4), auth(5), syslog(6), lpr(7), news(8), uucp(9), sys9(10), sys10(11), sys11(12), sys12(13), sys13(14), sys14(15), cron(16), local0(17), local1(18), local2(19), local3(20), local4(21), local5(22), local6(23), local7(24)}read-writemandatory
snAgSysLogBufferTable
OBJECT-TYPE
Dynamic system logging buffer table.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.2not-accessiblemandatory
snAgSysLogBufferEntry
OBJECT-TYPE
A row in the dynamic system logging buffer table.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.2.1not-accessiblemandatory
snAgSysLogBufferIndex
OBJECT-TYPE
The index to the dynamic system logging buffer table.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.2.1.1INTEGER (1..100)read-onlymandatory
snAgSysLogBufferTimeStamp
OBJECT-TYPE
A time stamp when the event is logged.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.2.1.2TimeTicksread-onlymandatory
snAgSysLogBufferCriticalLevel
OBJECT-TYPE
The critical level of this event.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.2.1.3INTEGER {other(1), alert(2), critical(3), debugging(4), emergency(5), error(6), informational(7), notification(8), warning(9)}read-onlymandatory
snAgSysLogBufferMessage
OBJECT-TYPE
The system logging message.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.2.1.4DisplayStringread-onlymandatory
snAgSysLogBufferCalTimeStamp
OBJECT-TYPE
A time stamp when the event is logged. This object returns a NULL terminated time stamp string if the system calendar time was set. It returns a zero length string if the system calendar time was not set.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.2.1.5DisplayStringread-onlymandatory
snAgStaticSysLogBufferTable
OBJECT-TYPE
Static system logging buffer table.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.3not-accessiblemandatory
snAgStaticSysLogBufferEntry
OBJECT-TYPE
A row in the static system logging buffer table.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.3.1not-accessiblemandatory
snAgStaticSysLogBufferIndex
OBJECT-TYPE
The index to the static system logging buffer table.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.3.1.1INTEGER (1..100)read-onlymandatory
snAgStaticSysLogBufferTimeStamp
OBJECT-TYPE
A time stamp when the event is logged.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.3.1.2TimeTicksread-onlymandatory
snAgStaticSysLogBufferCriticalLevel
OBJECT-TYPE
The critical level of this event.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.3.1.3INTEGER {other(1), alert(2), critical(3), debugging(4), emergency(5), error(6), informational(7), notification(8), warning(9)}read-onlymandatory
snAgStaticSysLogBufferMessage
OBJECT-TYPE
The system logging message.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.3.1.4DisplayStringread-onlymandatory
snAgStaticSysLogBufferCalTimeStamp
OBJECT-TYPE
A time stamp when the event is logged. This object returns a NULL terminated time stamp string if the system calendar time was set. It returns a zero length string if the system calendar time was not set.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.3.1.5DisplayStringread-onlymandatory
snAgentSysParaConfig
OBJECT-IDENTITY
1.3.6.1.4.1.11.2.3.7.11.12.1.2.7
snAgentSysParaConfigTable
OBJECT-TYPE
A table of Agent of each board.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.7.1not-accessiblemandatory
snAgentSysParaConfigEntry
OBJECT-TYPE
A row in the Agent System Parameters Configuation table.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.7.1.1not-accessiblemandatory
snAgentSysParaConfigIndex
OBJECT-TYPE
The index to the Agent System Parameters Configuation Table.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.7.1.1.1INTEGERread-onlymandatory
snAgentSysParaConfigDescription
OBJECT-TYPE
The main board description string.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.7.1.1.2DisplayString (SIZE(0..32))read-onlymandatory
snAgentSysParaConfigMin
OBJECT-TYPE
The minimum value of this Agent System Parameter.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.7.1.1.3INTEGERread-onlymandatory
snAgentSysParaConfigMax
OBJECT-TYPE
The maximum value of this Agent System Parameter.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.7.1.1.4INTEGERread-onlymandatory
snAgentSysParaConfigDefault
OBJECT-TYPE
The default value of this Agent System Parameter.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.7.1.1.5INTEGERread-onlymandatory
snAgentSysParaConfigCurrent
OBJECT-TYPE
The current configurated value of this Agent System Parameter.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.7.1.1.6INTEGERread-writemandatory
snAgentConfigModule
OBJECT-IDENTITY
1.3.6.1.4.1.11.2.3.7.11.12.1.2.8
snAgentConfigModuleTable
OBJECT-TYPE
A table of each configured module information.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.8.1not-accessiblemandatory
snAgentConfigModuleEntry
OBJECT-TYPE
A row in the Agent Configured Module table.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.8.1.1not-accessiblemandatory
snAgentConfigModuleIndex
OBJECT-TYPE
The index to the Agent Configured Module Table.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.8.1.1.1INTEGER (1..8)read-onlymandatory
snAgentConfigModuleType
OBJECT-TYPE
The Configured Module Type.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.8.1.1.2INTEGER {bi8PortGigManagementModule(0), bi4PortGigManagementModule(1), bi16PortCopperManagementModule(2), bi4PortGigModule(3), fi2PortGigManagementModule(4), fi4PortGigManagementModule(5), bi8PortGigCopperManagementModule(6), fi8PortGigManagementModule(7), bi8PortGigModule(8), bi24PortCopperModule(10), fi24PortCopperModule(11), bi16Port100FXModule(12), bi8Port100FXModule(13), bi8PortGigCopperModule(14), bi2PortGigManagementModule(18), bi24Port100FXModule(19), bi0PortManagementModule(20), pos622MbsModule(21), pos155MbsModule(22), bi2PortGigModule(23), bi2PortGigCopperModule(24), fi2PortGigModule(25), fi4PortGigModule(26), fi8PortGigModule(27), fi8PortGigCopperModule(28), fi8PortGigCopperManagementModule(29), pos155Mbs2PModule(30), fi2PortGigCopperManagementModule(31), fi4PortGigCopperManagementModule(32), bi4PortGigCopperManagementModule(33), bi2PortGigCopperManagementModule(34)}read-writemandatory
snAgentConfigModuleRowStatus
OBJECT-TYPE
To create or delete a configured module table entry.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.8.1.1.3INTEGER {other(1), valid(2), delete(3), create(4)}read-writemandatory
snAgentUser
OBJECT-IDENTITY
1.3.6.1.4.1.11.2.3.7.11.12.1.2.9
snAgentUserGbl
OBJECT-IDENTITY
1.3.6.1.4.1.11.2.3.7.11.12.1.2.9.1
snAgentUserMaxAccnt
OBJECT-TYPE
Maximum number of user account entries can be configured.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.9.1.1INTEGERread-onlymandatory
snAgentUserAccntTable
OBJECT-TYPE
A table of user account information.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.9.2not-accessiblemandatory
snAgentUserAccntEntry
OBJECT-TYPE
A row in the Agent User table.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.9.2.1not-accessiblemandatory
snAgentUserAccntName
OBJECT-TYPE
The user name.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.9.2.1.1DisplayString (SIZE(1..48))read-onlymandatory
snAgentUserAccntPassword
OBJECT-TYPE
The user password.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.9.2.1.2DisplayString (SIZE(0..48))read-writemandatory
snAgentUserAccntEncryptCode
OBJECT-TYPE
The password encryption method code.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.9.2.1.3INTEGERread-writemandatory
snAgentUserAccntPrivilege
OBJECT-TYPE
The user privilege.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.9.2.1.4INTEGERread-writemandatory
snAgentUserAccntRowStatus
OBJECT-TYPE
To create or delete a user account table entry.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.9.2.1.5INTEGER {other(1), valid(2), delete(3), create(4), modify(5)}read-writemandatory
snAgentRedundant
OBJECT-IDENTITY
1.3.6.1.4.1.11.2.3.7.11.12.1.2.10
snAgentRedunGbl
OBJECT-IDENTITY
1.3.6.1.4.1.11.2.3.7.11.12.1.2.10.1
snAgentRedunActiveMgmtMod
OBJECT-TYPE
Slot number of the active management module. Setting this object does not take effect immediately. Saving configuration data to flash storage and reboot the system are required to take effect. Setting a value of 0 requests the system to auto-select an active management module after power up.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.10.1.1INTEGERread-writemandatory
snAgentRedunSyncConfig
OBJECT-TYPE
Frequency of the backup management module copying the configuration data from the active management module. Each unit is 1 second. Setting a value 0 will disable the synchronization copy. Setting a negative value will initiate the synchronization copy once immediately.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.10.1.2INTEGERread-writemandatory
snAgentRedunBkupCopyBootCode
OBJECT-TYPE
If enabled(1), the backup management module copies the boot code from the active management module to its boot code flash storage after power up, and whenever the active management module's boot code is updated. The backup management module does not copy if both boot codes were identical.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.10.1.3INTEGER {disabled(0), enabled(1)}read-writemandatory
snAgentEnableMgmtModRedunStateChangeTrap
OBJECT-TYPE
Indicates whether the SNMP agent process is permitted to generate management module redundancy state change traps.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.10.1.4INTEGER {disabled(0), enabled(1)}read-writemandatory
snAgentRedunBkupBootLoad
OBJECT-TYPE
Action object to down load a new boot code from boot flash storage of the active management module to the backup management module. The following are returned values from get operation: normal(1)............no operation operationError(17)...error codes The following are input values from set operation: downloadBackup(20)...download the boot code from the active management module to the backup management module Any set operation is rejected during loading until error or normal state is reached.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.10.1.5INTEGER {normal(1), operationError(17), downloadBackup(20)}read-writemandatory
snAgentRedunSwitchOver
OBJECT-TYPE
To force a switch-over from standby to active state if the backup management module exists in a chassis.
1.3.6.1.4.1.11.2.3.7.11.12.1.2.10.1.6INTEGER {other(1), reset(2)}read-writemandatory
snStackGen
OBJECT-IDENTITY
1.3.6.1.4.1.11.2.3.7.11.12.1.5.1
snStackPriSwitchMode
OBJECT-TYPE
The Stackable Management Primary Switch mode either enabled or disabled and the default is disabled mode. enabled(1)...........primary switch enabled disabled(0)..........primary switch disabled
1.3.6.1.4.1.11.2.3.7.11.12.1.5.1.1INTEGER {disabled(0), enabled(1)}read-writemandatory
snStackMaxSecSwitch
OBJECT-TYPE
The Maximum Secondary Switches are allowed in the Stackable Management Group.
1.3.6.1.4.1.11.2.3.7.11.12.1.5.1.2INTEGERread-onlymandatory
snStackTotalSecSwitch
OBJECT-TYPE
The Total Secondary Switches currently connected to the Stackable Management Group.
1.3.6.1.4.1.11.2.3.7.11.12.1.5.1.3INTEGERread-onlymandatory
snStackSyncAllSecSwitch
OBJECT-TYPE
Synchronize all the secondary switches in the Stackable Management Group with the following commands. device(2)...........device related parameters. global(3)...........global parameters. local(4)............local parameters. The return result of the above commands are either normal(0)...........normal condition. invalid(1)...........invalid result.
1.3.6.1.4.1.11.2.3.7.11.12.1.5.1.4INTEGER {normal(0), invalid(1), device(2), global(3), local(4)}read-writemandatory
snStackSmSlotIndex
OBJECT-TYPE
The Slot 0 is the Master slot and Slot 1-8 are slaves. All the slot-based MIB data can be retrieved with respect to this slot index such as snChassis global MIB.
1.3.6.1.4.1.11.2.3.7.11.12.1.5.1.5INTEGER (0..8)read-writemandatory
snStackFmpSetProcess
OBJECT-TYPE
normal(0) - The set process is either in an idle state or FMP-SET-SUCCESS state. pending(1) - The pending process is waiting for the result of an FMP-SET. failure(2) - The failure result of an FMP-SET.
1.3.6.1.4.1.11.2.3.7.11.12.1.5.1.6INTEGER {normal(0), pending(1), failure(2)}read-onlymandatory
snStackSecSwitchInfo
OBJECT-IDENTITY
1.3.6.1.4.1.11.2.3.7.11.12.1.5.2
snStackSecSwitchTable
OBJECT-TYPE
If snSwGroupOperMode is configured as basic mode which is VLAN by Port, Layer2 switching, then this table is valid. Each VLAN switch port could have a number of VLAN IDs.
1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1not-accessiblemandatory
snStackSecSwitchEntry
OBJECT-TYPE
An entry in the Stackable Management Secondary Switch Information table.
1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1.1not-accessiblemandatory
snStackSecSwitchIndex
OBJECT-TYPE
The secondary switch index must not be greater than the snStackMaxSecSwitch.
1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1.1.1INTEGER (1..26)read-onlymandatory
snStackSecSwitchSlotId
OBJECT-TYPE
The secondary switch slot ID must be set before the Configuration command sent from the primary switch to the secondary switch either manually or automatically - snStackSecSwitchCfgCmd.
1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1.1.2INTEGER (1..26)read-writemandatory
snStackSecSwitchPortCnts
OBJECT-TYPE
The number of ports in this secondary switch.
1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1.1.3INTEGER (1..26)read-onlymandatory
snStackSecSwitchEnabled
OBJECT-TYPE
The secondary switch has been selected to Stackable Management Group.
1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1.1.4INTEGER {disabled(0), enabled(1)}read-writemandatory
snStackSecSwitchAck
OBJECT-TYPE
The secondary switch has sent reponse to the primary switch.
1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1.1.5INTEGER {disabled(0), enabled(1)}read-onlymandatory
snStackSecSwitchMacAddr
OBJECT-TYPE
The secondary switch physical address. The physical address represents a MAC Station.
1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1.1.6MacAddressread-onlymandatory
snStackSecSwitchSyncCmd
OBJECT-TYPE
Synchronize the secondary switches in the Stackable Management Group with the following commands. device(2)...........device related parameters. global(3)...........global parameters. local(4)............local parameters. The return result of the above commands are either normal(0)...........normal condition. invalid(1)...........invalid result.
1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1.1.7INTEGER {normal(0), invalid(1), device(2), global(3), local(4)}read-writemandatory
snStackSecSwitchIpAddr
OBJECT-TYPE
The secondary switch IP Address and is used for manual-command of snStackSecSwitchCfgCmd.
1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1.1.8IpAddressread-writemandatory
snStackSecSwitchSubnetMask
OBJECT-TYPE
The secondary switch IP Subnet Mask and is used for manual-command of snStackSecSwitchCfgCmd.
1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1.1.9IpAddressread-writemandatory
snStackSecSwitchCfgCmd
OBJECT-TYPE
snStackSecSwitchSlotId must be set before the Configuration command sent from the primary switch to the secondary switch either manually or automatically. auto(2)...........auto-configuration command sent. manual(3).........manual-configuration command sent. if manual-mode is used, snStackSecSwitchIpAddr and snStackSecSwitchSubnetMask must be first set before this command is sent. The return result of the above commands are either normal(0)...........normal condition. invalid(1)..........invalid result.
1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1.1.10INTEGER {normal(0), invalid(1), auto(2), manual(3)}read-writemandatory