MIBs Depot

FOUNDRY-SN-OSPF-GROUP-MIB

Registered at
1.3.6.1.4.1.1991.1.2.4
Last updated
2010-06-02 00:00
Organization
Brocade Communications Systems, Inc.
Revisions
2010-06-02 00:00, 2009-09-30 00:00
Namespace
extreme
Source file
FOUNDRY-SN-OSPF-GROUP-MIB
Digest
sha256:0c2a743f418708720bec8565674ada41f33f00054ced72e32ebf3a253f054a28

Description

Copyright 1996-2010 Brocade Communications Systems, Inc. All rights reserved. This Brocade Communications Systems SNMP Management Information Base Specification embodies Brocade Communications Systems' confidential and proprietary intellectual property. Brocade Communications Systems retains all title and ownership in the Specification, including any revisions. This Specification is supplied AS IS, and Brocade Communications Systems makes no warranty, either express or implied, as to the use, operation, condition, or performance of the specification, and any unintended consequence it may on the user environment.

Contact

Technical Support Center 130 Holger Way, San Jose, CA 95134 Email: ipsupport@brocade.com Phone: 1-800-752-8061 URL: www.brocade.com

Imports

FromSymbols
FOUNDRY-SN-ROOT-MIBrouter
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP
SNMPv2-SMICounter32, Gauge32, Integer32, IpAddress, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, iso
SNMPv2-TCDisplayString, TEXTUAL-CONVENTION

Imported by

2 module(s) in this corpus import this one.

Load order

Every file a consumer needs in order to load this module, dependencies first.

FOUNDRY-SN-OSPF-GROUP-MIB
FOUNDRY-SN-ROOT-MIB
SNMPv2-CONF
SNMPv2-SMI
SNMPv2-TC

Textual conventions

NameOIDSyntaxAccessStatus
AreaID
TEXTUAL-CONVENTION
The Area ID, in OSPF, has the same format as an IP Address, but has the function of defining a summarization point for Link State Advertisements
current
BigMetric
TEXTUAL-CONVENTION
0..'FFFFFF'h
current
DesignatedRouterPriority
TEXTUAL-CONVENTION
The range of ifIndex, i.e. (1..ifNumber) Potential Priorities for the Designated Router Election
current
HelloRange
TEXTUAL-CONVENTION
1..'FFFF'h
current
Metric
TEXTUAL-CONVENTION
The OSPF Metric is defined as an unsigned value in the range 0..'FFFF'h
current
PositiveInteger
TEXTUAL-CONVENTION
0..'7FFFFFFF'h
current
RouterID
TEXTUAL-CONVENTION
The Router ID, in OSPF, has the same format as an IP Address, but identifies the router independent of its IP Address.
current
RtrStatus
TEXTUAL-CONVENTION
RtrStatus Values
current
TOSType
TEXTUAL-CONVENTION
Type of Service is defined as a mapping to the IP Type of Service Flags as defined in the Router Requirements Document: Type of Service is defined as a mapping to the IP Type of Service Flags as defined in the IP Forwarding Table MIB +-----+-----+-----+-----+-----+-----+-----+-----+ | | | | | PRECEDENCE | TYPE OF SERVICE | 0 | | | | | +-----+-----+-----+-----+-----+-----+-----+-----+ IP TOS IP TOS Field Policy Field Policy Contents Code Contents Code 0 0 0 0 ==> 0 0 0 0 1 ==> 2 0 0 1 0 ==> 4 0 0 1 1 ==> 6 0 1 0 0 ==> 8 0 1 0 1 ==> 10 0 1 1 0 ==> 12 0 1 1 1 ==> 14 1 0 0 0 ==> 16 1 0 0 1 ==> 18 1 0 1 0 ==> 20 1 0 1 1 ==> 22 1 1 0 0 ==> 24 1 1 0 1 ==> 26 1 1 1 0 ==> 28 1 1 1 1 ==> 30 The remaining values are left for future definition.
current
TruthVal
TEXTUAL-CONVENTION
Boolean Values
current
UpToMaxAge
TEXTUAL-CONVENTION
current

Objects

NameOIDSyntaxAccessStatus
snOspfGen
OBJECT-IDENTITY
1.3.6.1.4.1.1991.1.2.4.1
snOspfRouterId
OBJECT-TYPE
A 32-bit integer uniquely identifying the router in the Autonomous System. By convention, to ensure uniqueness, this should default to the value of one of the router's IP interface addresses.
1.3.6.1.4.1.1991.1.2.4.1.1RouterIDread-writecurrent
snOspfAdminStat
OBJECT-TYPE
The administrative status of OSPF in the router. The value 'enabled' denotes that the OSPF Process is active on at least one interface; 'disabled' disables it on all interfaces.
1.3.6.1.4.1.1991.1.2.4.1.2RtrStatusread-writecurrent
snOspfASBdrRtrStatus
OBJECT-TYPE
A flag to note whether this router is an Autonomous System border router.
1.3.6.1.4.1.1991.1.2.4.1.3TruthValread-writecurrent
snOspfRedisMode
OBJECT-TYPE
The Redistribution status of OSPF in the router. The value 'enabled' denotes that the OSPF Redistribution is active; 'disabled' disables it on the router.
1.3.6.1.4.1.1991.1.2.4.1.4RtrStatusread-writecurrent
snOspfDefaultOspfMetricValue
OBJECT-TYPE
The metric of using a default OSPF Metric value on this route.
1.3.6.1.4.1.1991.1.2.4.1.5INTEGER (1..65535)read-writecurrent
snOspfExternLSACount
OBJECT-TYPE
The number of external (LS type 5) link-state advertisements in the link-state database.
1.3.6.1.4.1.1991.1.2.4.1.6Gauge32read-onlycurrent
snOspfExternLSACksumSum
OBJECT-TYPE
The 32-bit unsigned sum of the LS checksums of the external link-state advertisements contained in the link-state database. This sum can be used to determine if there has been a change in a router's link state database, and to compare the link-state database of two routers.
1.3.6.1.4.1.1991.1.2.4.1.7Integer32read-onlycurrent
snOspfOriginateNewLSAs
OBJECT-TYPE
The number of new link-state advertisements that have been originated. This number is incremented each time the router originates a new LSA.
1.3.6.1.4.1.1991.1.2.4.1.8Counter32read-onlycurrent
snOspfRxNewLSAs
OBJECT-TYPE
The number of link-state advertisements received determined to be new instantiations. This number does not include newer instantiations of self-originated link-state advertisements.
1.3.6.1.4.1.1991.1.2.4.1.9Counter32read-onlycurrent
snOspfOspfRedisMetricType
OBJECT-TYPE
type1: For External Type 1 (comparable value) the intra-area and inter-area routes, it is an OSPF metric plus the External Metric. type2: For external Type 2 (non-comparable value) routes, it is the external metric.
1.3.6.1.4.1.1991.1.2.4.1.10INTEGER {type1(1), type2(2)}read-writecurrent
snOspfExtLsdbLimit
OBJECT-TYPE
The maximum number of non-default AS- external-LSAs entries that can be stored in the link-state database. If the value is -1, then there is no limit. When the number of non-default AS-external-LSAs in a router's link-state database reaches ospfExtLsdbLimit, the router enters Overflow- State. The router never holds more than ospfExtLsdbLimit non-default AS-external-LSAs in its database. OspfExtLsdbLimit MUST be set identically in all routers attached to the OSPF backbone and/or any regular OSPF area. (i.e., OSPF stub areas and NSSAs are excluded).
1.3.6.1.4.1.1991.1.2.4.1.11Integer32read-writecurrent
snOspfExitOverflowInterval
OBJECT-TYPE
The number of seconds that, after entering OverflowState, a router will attempt to leave OverflowState. This allows the router to again originate non-default AS-external-LSAs. When set to 0, the router will not leave Overflow- State until restarted.
1.3.6.1.4.1.1991.1.2.4.1.12INTEGER (0..86400)read-writecurrent
snOspfRfc1583Compatibility
OBJECT-TYPE
This allows the ospf routing either compatible with RFC1583 or RFC2178. enabled(1)........activate RFC1583 compatibility rather than RFC2178 disabled(0).......disable RFC1583 compatibility and compatible to RFC2178.
1.3.6.1.4.1.1991.1.2.4.1.13INTEGER {disabled(0), enabled(1)}read-writecurrent
snOspfRouterIdFormat
OBJECT-TYPE
This object is used to specify whether RouterId is represented as IP Address or an Integer. The values that can be written are: integer(0).....as an integer. ipAddress(1)...as IP Address.
1.3.6.1.4.1.1991.1.2.4.1.14INTEGER {integer(0), ipAddress(1)}read-writecurrent
snOspfDistance
OBJECT-TYPE
OSPF Adminitrative distance. 0 if distance is not set.
1.3.6.1.4.1.1991.1.2.4.1.15INTEGER (0..255)read-writeobsolete
snOspfDistanceIntra
OBJECT-TYPE
OSPF Adminitrative distance - Intra Area.
1.3.6.1.4.1.1991.1.2.4.1.16INTEGER (1..255)read-writecurrent
snOspfDistanceInter
OBJECT-TYPE
OSPF Adminitrative distance - Inter Area.
1.3.6.1.4.1.1991.1.2.4.1.17INTEGER (1..255)read-writecurrent
snOspfDistanceExternal
OBJECT-TYPE
OSPF Adminitrative distance - External.
1.3.6.1.4.1.1991.1.2.4.1.18INTEGER (1..255)read-writecurrent
snOspfArea
OBJECT-IDENTITY
1.3.6.1.4.1.1991.1.2.4.2
snOspfAreaTable
OBJECT-TYPE
Information describing the configured parameters and cumulative statistics of the router's attached areas.
1.3.6.1.4.1.1991.1.2.4.2.1not-accessiblecurrent
snOspfAreaEntry
OBJECT-TYPE
Information describing the configured parameters and cumulative statistics of one of the router's attached areas.
1.3.6.1.4.1.1991.1.2.4.2.1.1not-accessiblecurrent
snOspfAreaId
OBJECT-TYPE
A 32-bit integer uniquely identifying an area. Area ID 0.0.0.0 is used for the OSPF backbone.
1.3.6.1.4.1.1991.1.2.4.2.1.1.1AreaIDread-onlycurrent
snOspfImportASExtern
OBJECT-TYPE
The area's support for importing AS external link- state advertisements. 0: Stub Area Type 1: Normal Area Type 2: NSSA Area Type
1.3.6.1.4.1.1991.1.2.4.2.1.1.2Integer32read-writecurrent
snOspfStubMetric
OBJECT-TYPE
The metric value applied at the default type of service(ospfMetric). By default, this equals the least metric at the type of service among the interfaces to other areas. This Object exist if only if the value of snOspfAreaSummary is snOspfAreaSummary(2); Otherwise, an SNMP_GET/GET_NEXT attempt of this Object will return NO_SUCH_NAME.
1.3.6.1.4.1.1991.1.2.4.2.1.1.3BigMetricread-writecurrent
snOspfAreaRowStatus
OBJECT-TYPE
This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid
1.3.6.1.4.1.1991.1.2.4.2.1.1.4INTEGER {invalid(1), valid(2), delete(3), create(4), modify(5)}read-writecurrent
snOspfAreaIdFormat
OBJECT-TYPE
This object is used to specify whether AreaId is represented as IP Address or an Integer. The values that can be written are: integer(0).....as an integer. ipAddress(1)...as IP Address.
1.3.6.1.4.1.1991.1.2.4.2.1.1.5INTEGER {integer(0), ipAddress(1)}read-writecurrent
snOspfAddrRange
OBJECT-IDENTITY
1.3.6.1.4.1.1991.1.2.4.3
snOspfAreaRangeTable
OBJECT-TYPE
A range if IP addresses specified by an IP address/IP network mask pair. For example, class B address range of X.X.X.X with a network mask of 255.255.0.0 includes all IP addresses from X.X.0.0 to X.X.255.255
1.3.6.1.4.1.1991.1.2.4.3.1not-accessiblecurrent
snOspfAreaRangeEntry
OBJECT-TYPE
A range if IP addresses specified by an IP address/IP network mask pair. For example, class B address range of X.X.X.X with a network mask of 255.255.0.0 includes all IP addresses from X.X.0.0 to X.X.255.255
1.3.6.1.4.1.1991.1.2.4.3.1.1not-accessiblecurrent
snOspfAreaRangeAreaID
OBJECT-TYPE
The Area the Address Range is to be found within.
1.3.6.1.4.1.1991.1.2.4.3.1.1.1AreaIDread-onlycurrent
snOspfAreaRangeNet
OBJECT-TYPE
The IP Address of the Net or Subnet indicated by the range.
1.3.6.1.4.1.1991.1.2.4.3.1.1.2IpAddressread-onlycurrent
snOspfAreaRangeMask
OBJECT-TYPE
The Subnet Mask that pertains to the Net or Subnet.
1.3.6.1.4.1.1991.1.2.4.3.1.1.3IpAddressread-writecurrent
snOspfAreaRangeRowStatus
OBJECT-TYPE
This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid
1.3.6.1.4.1.1991.1.2.4.3.1.1.4INTEGER {invalid(1), valid(2), delete(3), create(4), modify(5)}read-writecurrent
snOspfAreaRangeAreaIdFormat
OBJECT-TYPE
This object is used to specify whether AreaId is represented as IP Address or an Integer. The values that can be written are: integer(0).....as an integer. ipAddress(1)...as IP Address.
1.3.6.1.4.1.1991.1.2.4.3.1.1.5INTEGER {integer(0), ipAddress(1)}read-onlycurrent
snOspfIntf
OBJECT-IDENTITY
1.3.6.1.4.1.1991.1.2.4.4
snOspfIfTable
OBJECT-TYPE
The OSPF Interface Table describes the interfaces from the viewpoint of OSPF.
1.3.6.1.4.1.1991.1.2.4.4.1not-accessibledeprecated
snOspfIfEntry
OBJECT-TYPE
The OSPF Interface Entry describes one interface from the viewpoint of OSPF.
1.3.6.1.4.1.1991.1.2.4.4.1.1not-accessibledeprecated
snOspfIfPort
OBJECT-TYPE
The physical router port of this OSPF interface.
1.3.6.1.4.1.1991.1.2.4.4.1.1.1Integer32read-onlydeprecated
snOspfIfAreaId
OBJECT-TYPE
A 32-bit integer uniquely identifying the area to which the interface connects. Area ID 0.0.0.0 is used for the OSPF backbone.
1.3.6.1.4.1.1991.1.2.4.4.1.1.2AreaIDread-writedeprecated
snOspfIfAdminStat
OBJECT-TYPE
The OSPF interface's administrative status. The value 'enabled' denotes that neighbor relationships may be formed on the interface, and the interface will be advertised as an internal route to some area. The value 'disabled' denotes that the interface is external to OSPF.
1.3.6.1.4.1.1991.1.2.4.4.1.1.3RtrStatusread-writedeprecated
snOspfIfRtrPriority
OBJECT-TYPE
The priority of this interface. Used in multi-access networks, this field is used in the designated router election algorithm. The value 0 signifies that the router is not eligible to become the designated router on this particular network. In the event of a tie in this value, routers will use their router id as a tie breaker.
1.3.6.1.4.1.1991.1.2.4.4.1.1.4DesignatedRouterPriorityread-writedeprecated
snOspfIfTransitDelay
OBJECT-TYPE
The estimated number of seconds it takes to transmit a link- state update packet over this interface.
1.3.6.1.4.1.1991.1.2.4.4.1.1.5UpToMaxAgeread-writedeprecated
snOspfIfRetransInterval
OBJECT-TYPE
The number of seconds between link-state advertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database description and link-state request packets.
1.3.6.1.4.1.1991.1.2.4.4.1.1.6UpToMaxAgeread-writedeprecated
snOspfIfHelloInterval
OBJECT-TYPE
The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for all routers attached to a common network.
1.3.6.1.4.1.1991.1.2.4.4.1.1.7HelloRangeread-writedeprecated
snOspfIfRtrDeadInterval
OBJECT-TYPE
The number of seconds that a router's Hello packets have not been seen before it's neighbors declare the router down. This should be some multiple of the Hello interval. This value must be the same for all routers attached to a common network.
1.3.6.1.4.1.1991.1.2.4.4.1.1.8PositiveIntegerread-writedeprecated
snOspfIfAuthType
OBJECT-TYPE
The authentication type specified for an interface. Additional authentication types may be assigned locally on a per interface basis.
1.3.6.1.4.1.1991.1.2.4.4.1.1.9INTEGER (0..255)read-writedeprecated
snOspfIfAuthKey
OBJECT-TYPE
The Authentication Key. If the Area's Authorization Type is simplePassword, and the key length is shorter than 8 octets, the agent will left adjust and zero fill to 8 octets. When read, snOspfIfAuthKey always returns an Octet String of length zero.
1.3.6.1.4.1.1991.1.2.4.4.1.1.10OCTET STRING (SIZE(0..8))read-writedeprecated
snOspfIfMetricValue
OBJECT-TYPE
The metric of using this type of service on this interface. The default value of the TOS 0 Metric is 10^8 / ifSpeed.
1.3.6.1.4.1.1991.1.2.4.4.1.1.11INTEGER (1..65535)read-writedeprecated
snOspfIfRowStatus
OBJECT-TYPE
This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid
1.3.6.1.4.1.1991.1.2.4.4.1.1.12INTEGER {invalid(1), valid(2), delete(3), create(4), modify(5)}read-writedeprecated
snOspfIfMd5AuthKeyId
OBJECT-TYPE
The md5 authentication key ID. If the snOspfVirtIfAuthType is set to md5, the value of snOspfIfMd5AuthKeyId must be (1 to 255). This field identifies the algorithm and secret key used to create the message digest appended to the OSPF packet. Key Identifiers are unique per-interface (or equivalently, per-subnet).
1.3.6.1.4.1.1991.1.2.4.4.1.1.13INTEGER (0..255)read-writedeprecated
snOspfIfMd5AuthKey
OBJECT-TYPE
The MD5 Authentication Key. If the Area's Authorization Type is md5, and the key length is shorter than 16 octets, the agent will left adjust and zero fill to 16 octets. When read, snOspfIfMd5AuthKey always returns an Octet String of length zero.
1.3.6.1.4.1.1991.1.2.4.4.1.1.14OCTET STRING (SIZE(0..16))read-writedeprecated
snOspfIfMd5ActivationWaitTime
OBJECT-TYPE
The md5 authentication key activation wait time is specified in second and the maximum wait time is 14400 seconds (4 hours).
1.3.6.1.4.1.1991.1.2.4.4.1.1.15INTEGER (0..14400)read-writedeprecated
snOspfIfAreaIdFormat
OBJECT-TYPE
This object is used to specify whether AreaId is represented as IP Address or an Integer. The values that can be written are: integer(0).....as an integer. ipAddress(1)...as IP Address.
1.3.6.1.4.1.1991.1.2.4.4.1.1.16INTEGER {integer(0), ipAddress(1)}read-onlydeprecated
snOspfIfPassiveMode
OBJECT-TYPE
This object control the passive mode of this interface.
1.3.6.1.4.1.1991.1.2.4.4.1.1.17INTEGER {disabled(0), enabled(1)}read-writedeprecated
snOspfIfDatabaseFilterAllOut
OBJECT-TYPE
This object control the filtering of outgoing OSPF LSA on this interface.
1.3.6.1.4.1.1991.1.2.4.4.1.1.18INTEGER {disabled(0), enabled(1)}read-writedeprecated
snOspfIfMtuIgnore
OBJECT-TYPE
This object control MTU detection mode of this interface.
1.3.6.1.4.1.1991.1.2.4.4.1.1.19INTEGER {disabled(0), enabled(1)}read-writedeprecated
snOspfIfNetworkP2mp
OBJECT-TYPE
This object enable/disable P2MP mode of this interface.
1.3.6.1.4.1.1991.1.2.4.4.1.1.20INTEGER {disabled(0), enabled(1)}read-writedeprecated
snOspfIf2Table
OBJECT-TYPE
The OSPF Interface Table describes the interfaces from the viewpoint of OSPF.
1.3.6.1.4.1.1991.1.2.4.4.2not-accessiblecurrent
snOspfIf2Entry
OBJECT-TYPE
The OSPF Interface Entry describes one interface from the viewpoint of OSPF.
1.3.6.1.4.1.1991.1.2.4.4.2.1not-accessiblecurrent
snOspfIf2Port
OBJECT-TYPE
The physical router port of this OSPF interface.
1.3.6.1.4.1.1991.1.2.4.4.2.1.1Integer32read-onlycurrent
snOspfIf2AreaId
OBJECT-TYPE
A 32-bit integer uniquely identifying the area to which the interface connects. Area ID 0.0.0.0 is used for the OSPF backbone.
1.3.6.1.4.1.1991.1.2.4.4.2.1.2AreaIDread-writecurrent
snOspfIf2AdminStat
OBJECT-TYPE
The OSPF interface's administrative status. The value 'enabled' denotes that neighbor relationships may be formed on the interface, and the interface will be advertised as an internal route to some area. The value 'disabled' denotes that the interface is external to OSPF.
1.3.6.1.4.1.1991.1.2.4.4.2.1.3RtrStatusread-writecurrent
snOspfIf2RtrPriority
OBJECT-TYPE
The priority of this interface. Used in multi-access networks, this field is used in the designated router election algorithm. The value 0 signifies that the router is not eligible to become the designated router on this particular network. In the event of a tie in this value, routers will use their router id as a tie breaker.
1.3.6.1.4.1.1991.1.2.4.4.2.1.4DesignatedRouterPriorityread-writecurrent
snOspfIf2TransitDelay
OBJECT-TYPE
The estimated number of seconds it takes to transmit a link- state update packet over this interface.
1.3.6.1.4.1.1991.1.2.4.4.2.1.5UpToMaxAgeread-writecurrent
snOspfIf2RetransInterval
OBJECT-TYPE
The number of seconds between link-state advertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database description and link-state request packets.
1.3.6.1.4.1.1991.1.2.4.4.2.1.6UpToMaxAgeread-writecurrent
snOspfIf2HelloInterval
OBJECT-TYPE
The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for all routers attached to a common network.
1.3.6.1.4.1.1991.1.2.4.4.2.1.7HelloRangeread-writecurrent
snOspfIf2RtrDeadInterval
OBJECT-TYPE
The number of seconds that a router's Hello packets have not been seen before it's neighbors declare the router down. This should be some multiple of the Hello interval. This value must be the same for all routers attached to a common network.
1.3.6.1.4.1.1991.1.2.4.4.2.1.8PositiveIntegerread-writecurrent
snOspfIf2AuthType
OBJECT-TYPE
The authentication type specified for an interface. Additional authentication types may be assigned locally on a per interface basis.
1.3.6.1.4.1.1991.1.2.4.4.2.1.9INTEGER (0..255)read-writecurrent
snOspfIf2AuthKey
OBJECT-TYPE
The Authentication Key. If the Area's Authorization Type is simplePassword, and the key length is shorter than 8 octets, the agent will left adjust and zero fill to 8 octets. When read, snOspfIf2AuthKey always returns an Octet String of length zero.
1.3.6.1.4.1.1991.1.2.4.4.2.1.10OCTET STRING (SIZE(0..8))read-writecurrent
snOspfIf2MetricValue
OBJECT-TYPE
The metric of using this type of service on this interface. The default value of the TOS 0 Metric is 10^8 / ifSpeed.
1.3.6.1.4.1.1991.1.2.4.4.2.1.11INTEGER (1..65535)read-writecurrent
snOspfIf2RowStatus
OBJECT-TYPE
This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid
1.3.6.1.4.1.1991.1.2.4.4.2.1.12INTEGER {invalid(1), valid(2), delete(3), create(4), modify(5)}read-writecurrent
snOspfIf2Md5AuthKeyId
OBJECT-TYPE
The md5 authentication key ID. If the snOspfVirtIfAuthType is set to md5, the value of snOspfIf2Md5AuthKeyId must be (1 to 255). This field identifies the algorithm and secret key used to create the message digest appended to the OSPF packet. Key Identifiers are unique per-interface (or equivalently, per-subnet).
1.3.6.1.4.1.1991.1.2.4.4.2.1.13INTEGER (0..255)read-writecurrent
snOspfIf2Md5AuthKey
OBJECT-TYPE
The MD5 Authentication Key. If the Area's Authorization Type is md5, and the key length is shorter than 16 octets, the agent will left adjust and zero fill to 16 octets. When read, snOspfIf2Md5AuthKey always returns an Octet String of length zero.
1.3.6.1.4.1.1991.1.2.4.4.2.1.14OCTET STRING (SIZE(0..16))read-writecurrent
snOspfIf2Md5ActivationWaitTime
OBJECT-TYPE
The md5 authentication key activation wait time is specified in second and the maximum wait time is 14400 seconds (4 hours).
1.3.6.1.4.1.1991.1.2.4.4.2.1.15INTEGER (0..14400)read-writecurrent
snOspfIf2AreaIdFormat
OBJECT-TYPE
This object is used to specify whether AreaId is represented as IP Address or an Integer. The values that can be written are: integer(0).....as an integer. ipAddress(1)...as IP Address.
1.3.6.1.4.1.1991.1.2.4.4.2.1.16INTEGER {integer(0), ipAddress(1)}read-onlycurrent
snOspfIf2PassiveMode
OBJECT-TYPE
This object control the passive mode of this interface.
1.3.6.1.4.1.1991.1.2.4.4.2.1.17INTEGER {disabled(0), enabled(1)}read-writecurrent
snOspfIf2DatabaseFilterAllOut
OBJECT-TYPE
This object control the filtering of outgoing OSPF LSA on this interface.
1.3.6.1.4.1.1991.1.2.4.4.2.1.18INTEGER {disabled(0), enabled(1)}read-writecurrent
snOspfIf2MtuIgnore
OBJECT-TYPE
This object control MTU detection mode of this interface.
1.3.6.1.4.1.1991.1.2.4.4.2.1.19INTEGER {disabled(0), enabled(1)}read-writecurrent
snOspfIf2NetworkP2mp
OBJECT-TYPE
This object enable/disable P2MP mode of this interface.
1.3.6.1.4.1.1991.1.2.4.4.2.1.20INTEGER {disabled(0), enabled(1)}read-writecurrent
snOspfIf2NetworkP2pt
OBJECT-TYPE
This object enable/disable Point-to-Point mode of this interface.
1.3.6.1.4.1.1991.1.2.4.4.2.1.21INTEGER {disabled(0), enabled(1)}read-writecurrent
snOspfIf2NetworkNonBroadcast
OBJECT-TYPE
This object enable/disable non broadcast mode of this interface.
1.3.6.1.4.1.1991.1.2.4.4.2.1.22INTEGER {disabled(0), enabled(1)}read-writecurrent
snOspfVirtIf
OBJECT-IDENTITY
1.3.6.1.4.1.1991.1.2.4.5
snOspfVirtIfTable
OBJECT-TYPE
Information about this router's virtual interfaces.
1.3.6.1.4.1.1991.1.2.4.5.1not-accessiblecurrent
snOspfVirtIfEntry
OBJECT-TYPE
Information about a single Virtual Interface.
1.3.6.1.4.1.1991.1.2.4.5.1.1not-accessiblecurrent
snOspfVirtIfAreaID
OBJECT-TYPE
The Transit Area that the Virtual Link traverses. By definition, this is not 0.0.0.0
1.3.6.1.4.1.1991.1.2.4.5.1.1.1AreaIDread-onlycurrent
snOspfVirtIfNeighbor
OBJECT-TYPE
The Router ID of the Virtual Neighbor.
1.3.6.1.4.1.1991.1.2.4.5.1.1.2RouterIDread-onlycurrent
snOspfVirtIfTransitDelay
OBJECT-TYPE
The estimated number of seconds it takes to transmit a link- state update packet over this interface.
1.3.6.1.4.1.1991.1.2.4.5.1.1.3UpToMaxAgeread-writecurrent
snOspfVirtIfRetransInterval
OBJECT-TYPE
The number of seconds between link-state advertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database description and link-state request packets. This value should be well over the expected round-trip time.
1.3.6.1.4.1.1991.1.2.4.5.1.1.4UpToMaxAgeread-writecurrent
snOspfVirtIfHelloInterval
OBJECT-TYPE
The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for the virtual neighbor.
1.3.6.1.4.1.1991.1.2.4.5.1.1.5HelloRangeread-writecurrent
snOspfVirtIfRtrDeadInterval
OBJECT-TYPE
The number of seconds that a router's Hello packets have not been seen before it's neighbors declare the router down. This should be some multiple of the Hello interval. This value must be the same for the virtual neighbor.
1.3.6.1.4.1.1991.1.2.4.5.1.1.6PositiveIntegerread-writecurrent
snOspfVirtIfAuthType
OBJECT-TYPE
The authentication type specified for an interface. Additional authentication types may be assigned locally on a per interface basis.
1.3.6.1.4.1.1991.1.2.4.5.1.1.7INTEGER (0..255)read-writecurrent
snOspfVirtIfAuthKey
OBJECT-TYPE
If Authentication Type is simplePassword, the device will left adjust and zero fill to 8 octets. When read, snOspfVifAuthKey always returns a string of length zero.
1.3.6.1.4.1.1991.1.2.4.5.1.1.8OCTET STRING (SIZE(0..8))read-writecurrent
snOspfVirtIfRowStatus
OBJECT-TYPE
This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid
1.3.6.1.4.1.1991.1.2.4.5.1.1.9INTEGER {invalid(1), valid(2), delete(3), create(4), modify(5)}read-writecurrent
snOspfVirtIfMd5AuthKeyId
OBJECT-TYPE
The md5 authentication key ID. If the snOspfVirtIfAuthType is set to md5, the value of snOspfVirtIfMd5AuthKeyId must be (1 to 255). This field identifies the algorithm and secret key used to create the message digest appended to the OSPF packet. Key Identifiers are unique per-interface (or equivalently, per-subnet).
1.3.6.1.4.1.1991.1.2.4.5.1.1.10INTEGER (0..255)read-writecurrent
snOspfVirtIfMd5AuthKey
OBJECT-TYPE
The MD5 Authentication Key. If the Area's Authorization Type is md5, and the key length is shorter than 16 octets, the agent will left adjust and zero fill to 16 octets. When read, snOspfIfMd5AuthKey always returns an Octet String of length zero.
1.3.6.1.4.1.1991.1.2.4.5.1.1.11OCTET STRING (SIZE(0..16))read-writecurrent
snOspfVirtIfMd5ActivationWaitTime
OBJECT-TYPE
The md5 authentication key activation wait time is specified in second and the maximum wait time is 14400 seconds (4 hours).
1.3.6.1.4.1.1991.1.2.4.5.1.1.12INTEGER (0..14400)read-writecurrent
snOspfVirtIfAreaIdFormat
OBJECT-TYPE
This object is used to specify whether AreaId is represented as IP Address or an Integer. The values that can be written are: integer(0).....as an integer. ipAddress(1)...as IP Address.
1.3.6.1.4.1.1991.1.2.4.5.1.1.13INTEGER {integer(0), ipAddress(1)}read-onlycurrent
snOspfRedis
OBJECT-IDENTITY
1.3.6.1.4.1.1991.1.2.4.6
snOspfRedisTable
OBJECT-TYPE
The OSPF Redistribution Table contains a list of routes that could be imported into the OSPF domain.
1.3.6.1.4.1.1991.1.2.4.6.1not-accessiblecurrent
snOspfRedisEntry
OBJECT-TYPE
The OSPF Redistribution Entry specifies a particular RIP or Static route to be imported into the OSPF domain.
1.3.6.1.4.1.1991.1.2.4.6.1.1not-accessiblecurrent
snOspfRedisIndex
OBJECT-TYPE
The destination IP address that associates with this particular route.
1.3.6.1.4.1.1991.1.2.4.6.1.1.1INTEGER (1..64)read-onlycurrent
snOspfRedisIpAddress
OBJECT-TYPE
The destination IP address that associates with this particular route.
1.3.6.1.4.1.1991.1.2.4.6.1.1.2IpAddressread-writecurrent
snOspfRedisMask
OBJECT-TYPE
The Subnet Mask that pertains to this route.
1.3.6.1.4.1.1991.1.2.4.6.1.1.3IpAddressread-writecurrent
snOspfRedisAction
OBJECT-TYPE
The action to be taken if the route match this entry. noImport(0): - the route is NOT imported into OSPF Domain. import(1): - the route is imported into OSPF Domain as external type 2 route.
1.3.6.1.4.1.1991.1.2.4.6.1.1.4INTEGER {noImport(0), import(1)}read-writecurrent
snOspfRedisProtocol
OBJECT-TYPE
The imported routes into OSPF domain is set in the following: rip(1): - the RIP route. all(2): - all protocol route. static(3): - the static route. bgp(4): - the BGP route. connected(5): - the connected route. isis(6): - the ISIS route.
1.3.6.1.4.1.1991.1.2.4.6.1.1.5INTEGER {rip(1), all(2), static(3), bgp(4), connected(5), isis(6)}read-writecurrent
snOspfRedisSetOspfMetric
OBJECT-TYPE
The value indicates to which the route metric should match: disabled(0): - the route metric does NOT match the OSPF metric field. enabled(1): - the route metric matches the OSPF metric field.
1.3.6.1.4.1.1991.1.2.4.6.1.1.6INTEGER {disabled(0), enabled(1)}read-writecurrent
snOspfRedisOspfMetricValue
OBJECT-TYPE
The metric of using OSPF Metric value on this route.
1.3.6.1.4.1.1991.1.2.4.6.1.1.7Metricread-writecurrent
snOspfRedisMatchRipMetric
OBJECT-TYPE
The value indicates to which the route metric should match: disabled(0): - the route metric does NOT match the RIP metric field. enabled(1): - the route metric matches the RIP metric field.
1.3.6.1.4.1.1991.1.2.4.6.1.1.8INTEGER {disabled(0), enabled(1)}read-writecurrent
snOspfRedisRipMetricValue
OBJECT-TYPE
The metric of using RIP Metric value (1 to 15 hops) on this route.
1.3.6.1.4.1.1991.1.2.4.6.1.1.9INTEGER (1..15)read-writecurrent
snOspfRedisRowStatus
OBJECT-TYPE
This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid
1.3.6.1.4.1.1991.1.2.4.6.1.1.10INTEGER {invalid(1), valid(2), delete(3), create(4), modify(5)}read-writecurrent
snOspfNbr
OBJECT-IDENTITY
1.3.6.1.4.1.1991.1.2.4.7
snOspfNbrTable
OBJECT-TYPE
A table of non-virtual neighbor information.
1.3.6.1.4.1.1991.1.2.4.7.1not-accessiblecurrent
snOspfNbrEntry
OBJECT-TYPE
The information regarding a single neighbor.
1.3.6.1.4.1.1991.1.2.4.7.1.1not-accessiblecurrent
snOspfNbrEntryIndex
OBJECT-TYPE
The table entry index of this neighbor.
1.3.6.1.4.1.1991.1.2.4.7.1.1.1Integer32read-onlycurrent
snOspfNbrPort
OBJECT-TYPE
The physical port of this neighbor.
1.3.6.1.4.1.1991.1.2.4.7.1.1.2Integer32read-onlycurrent
snOspfNbrIpAddr
OBJECT-TYPE
The IP address of this neighbor.
1.3.6.1.4.1.1991.1.2.4.7.1.1.3IpAddressread-onlycurrent
snOspfNbrIndex
OBJECT-TYPE
The neighbor index of each port and each IP address.
1.3.6.1.4.1.1991.1.2.4.7.1.1.4Integer32read-onlycurrent
snOspfNbrRtrId
OBJECT-TYPE
A 32-bit integer (represented as a type IpAddress) uniquely identifying the neighboring router in the Autonomous System.
1.3.6.1.4.1.1991.1.2.4.7.1.1.5RouterIDread-onlycurrent
snOspfNbrOptions
OBJECT-TYPE
A Bit Mask corresponding to the neighbor's op- tions field. Bit 0, if set, indicates that the system will operate on Type of Service metrics other than TOS 0. If zero, the neighbor will ignore all metrics except the TOS 0 metric. Bit 1, if set, indicates that the associated area accepts and operates on external informa- tion; if zero, it is a stub area. Bit 2, if set, indicates that the system is ca- pable of routing IP Multicast datagrams; i.e., that it implements the Multicast Extensions to OSPF. Bit 3, if set, indicates that the associated area is an NSSA. These areas are capable of carrying type 7 external advertisements, which are translated into type 5 external advertise- ments at NSSA borders.
1.3.6.1.4.1.1991.1.2.4.7.1.1.6Integer32read-onlycurrent
snOspfNbrPriority
OBJECT-TYPE
The priority of this neighbor in the designat- ed router election algorithm. The value 0 sig- nifies that the neighbor is not eligible to be- come the designated router on this particular network.
1.3.6.1.4.1.1991.1.2.4.7.1.1.7DesignatedRouterPriorityread-onlycurrent
snOspfNbrState
OBJECT-TYPE
The State of the relationship with this Neigh- bor.
1.3.6.1.4.1.1991.1.2.4.7.1.1.8INTEGER {down(1), attempt(2), init(3), twoWay(4), exchangeStart(5), exchange(6), loading(7), full(8)}read-onlycurrent
snOspfNbrEvents
OBJECT-TYPE
The number of times this neighbor relationship has changed state, or an error has occurred.
1.3.6.1.4.1.1991.1.2.4.7.1.1.9Counter32read-onlycurrent
snOspfNbrLsRetransQLen
OBJECT-TYPE
The current length of the retransmission queue.
1.3.6.1.4.1.1991.1.2.4.7.1.1.10Gauge32read-onlycurrent
snOspfVirtNbr
OBJECT-IDENTITY
1.3.6.1.4.1.1991.1.2.4.8
snOspfVirtNbrTable
OBJECT-TYPE
A table of virtual neighbor information.
1.3.6.1.4.1.1991.1.2.4.8.1not-accessiblecurrent
snOspfVirtNbrEntry
OBJECT-TYPE
Virtual neighbor information.
1.3.6.1.4.1.1991.1.2.4.8.1.1not-accessiblecurrent
snOspfVirtNbrEntryIndex
OBJECT-TYPE
The table entry index of this virtual neighbor.
1.3.6.1.4.1.1991.1.2.4.8.1.1.1Integer32read-onlycurrent
snOspfVirtNbrArea
OBJECT-TYPE
The Transit Area Identifier.
1.3.6.1.4.1.1991.1.2.4.8.1.1.2AreaIDread-onlycurrent
snOspfVirtNbrRtrId
OBJECT-TYPE
A 32-bit integer uniquely identifying the neighboring router in the Autonomous System.
1.3.6.1.4.1.1991.1.2.4.8.1.1.3RouterIDread-onlycurrent
snOspfVirtNbrIpAddr
OBJECT-TYPE
The IP address this Virtual Neighbor is using.
1.3.6.1.4.1.1991.1.2.4.8.1.1.4IpAddressread-onlycurrent
snOspfVirtNbrOptions
OBJECT-TYPE
A bit map corresponding to the neighbor's options field. Thus, Bit 1, if set, indicates that the neighbor supports Type of Service Routing; if zero, no metrics other than TOS 0 are in use by the neighbor.
1.3.6.1.4.1.1991.1.2.4.8.1.1.5Integer32read-onlycurrent
snOspfVirtNbrState
OBJECT-TYPE
The state of the Virtual Neighbor Relationship.
1.3.6.1.4.1.1991.1.2.4.8.1.1.6INTEGER {down(1), attempt(2), init(3), twoWay(4), exchangeStart(5), exchange(6), loading(7), full(8)}read-onlycurrent
snOspfVirtNbrEvents
OBJECT-TYPE
The number of times this virtual link has changed its state, or an error has occurred.
1.3.6.1.4.1.1991.1.2.4.8.1.1.7Counter32read-onlycurrent
snOspfVirtNbrLSRetransQLen
OBJECT-TYPE
The current length of the retransmission queue.
1.3.6.1.4.1.1991.1.2.4.8.1.1.8Gauge32read-onlycurrent
snOspfVirtNbrAreaIdFormat
OBJECT-TYPE
This object is used to specify whether AreaId is represented as IP Address or an Integer. The values that can be written are: integer(0).....as an integer. ipAddress(1)...as IP Address.
1.3.6.1.4.1.1991.1.2.4.8.1.1.9INTEGER {integer(0), ipAddress(1)}read-onlycurrent
snOspfLsdb
OBJECT-IDENTITY
1.3.6.1.4.1.1991.1.2.4.9
snOspfLsdbTable
OBJECT-TYPE
The OSPF Process's Links State Database.
1.3.6.1.4.1.1991.1.2.4.9.1not-accessiblecurrent
snOspfLsdbEntry
OBJECT-TYPE
A single Link State Advertisement.
1.3.6.1.4.1.1991.1.2.4.9.1.1not-accessiblecurrent
snOspfLsdbEntryIndex
OBJECT-TYPE
The table entry index of this Link State Database.
1.3.6.1.4.1.1991.1.2.4.9.1.1.1Integer32read-onlycurrent
snOspfLsdbAreaId
OBJECT-TYPE
The 32 bit identifier of the Area from which the LSA was received.
1.3.6.1.4.1.1991.1.2.4.9.1.1.2AreaIDread-onlycurrent
snOspfLsdbType
OBJECT-TYPE
The type of the link state advertisement. Each link state type has a separate advertisement format.
1.3.6.1.4.1.1991.1.2.4.9.1.1.3INTEGER {routerLink(1), networkLink(2), summaryLink(3), asSummaryLink(4), asExternalLink(5), multicastLink(6), nssaExternalLink(7), opaqueLink(9), opaqueAreaLink(10), opaqueAsLink(11)}read-onlycurrent
snOspfLsdbLsId
OBJECT-TYPE
The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement.
1.3.6.1.4.1.1991.1.2.4.9.1.1.4IpAddressread-onlycurrent
snOspfLsdbRouterId
OBJECT-TYPE
The 32 bit number that uniquely identifies the originating router in the Autonomous System.
1.3.6.1.4.1.1991.1.2.4.9.1.1.5RouterIDread-onlycurrent
snOspfLsdbSequence
OBJECT-TYPE
The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.
1.3.6.1.4.1.1991.1.2.4.9.1.1.6Integer32read-onlycurrent
snOspfLsdbAge
OBJECT-TYPE
This field is the age of the link state advertisement in seconds.
1.3.6.1.4.1.1991.1.2.4.9.1.1.7Integer32read-onlycurrent
snOspfLsdbChecksum
OBJECT-TYPE
This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum.
1.3.6.1.4.1.1991.1.2.4.9.1.1.8Integer32read-onlycurrent
snOspfLsdbAdvertisement
OBJECT-TYPE
The entire Link State Advertisement, including its header.
1.3.6.1.4.1.1991.1.2.4.9.1.1.9OCTET STRING (SIZE(1..65535))read-onlycurrent
snOspfLsdbAreaIdFormat
OBJECT-TYPE
This object is used to specify whether AreaId is represented as IP Address or an Integer. The values that can be written are: integer(0).....as an integer. ipAddress(1)...as IP Address.
1.3.6.1.4.1.1991.1.2.4.9.1.1.10INTEGER {integer(0), ipAddress(1)}read-onlycurrent
snOspfExtLsdb
OBJECT-IDENTITY
1.3.6.1.4.1.1991.1.2.4.10
snOspfExtLsdbTable
OBJECT-TYPE
The OSPF Process's Links State Database.
1.3.6.1.4.1.1991.1.2.4.10.1not-accessiblecurrent
snOspfExtLsdbEntry
OBJECT-TYPE
A single Link State Advertisement.
1.3.6.1.4.1.1991.1.2.4.10.1.1not-accessiblecurrent
snOspfExtLsdbEntryIndex
OBJECT-TYPE
The table entry index of this Link State Database.
1.3.6.1.4.1.1991.1.2.4.10.1.1.1Integer32read-onlycurrent
snOspfExtLsdbType
OBJECT-TYPE
The type of the link state advertisement. Each link state type has a separate advertise- ment format.
1.3.6.1.4.1.1991.1.2.4.10.1.1.2INTEGER {asExternalLink(5)}read-onlycurrent
snOspfExtLsdbLsId
OBJECT-TYPE
The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement.
1.3.6.1.4.1.1991.1.2.4.10.1.1.3IpAddressread-onlycurrent
snOspfExtLsdbRouterId
OBJECT-TYPE
The 32 bit number that uniquely identifies the originating router in the Autonomous System.
1.3.6.1.4.1.1991.1.2.4.10.1.1.4RouterIDread-onlycurrent
snOspfExtLsdbSequence
OBJECT-TYPE
The sequence number field is a signed 32-bit integer. It is used to detect old and dupli- cate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.
1.3.6.1.4.1.1991.1.2.4.10.1.1.5Integer32read-onlycurrent
snOspfExtLsdbAge
OBJECT-TYPE
This field is the age of the link state adver- tisement in seconds.
1.3.6.1.4.1.1991.1.2.4.10.1.1.6Integer32read-onlycurrent
snOspfExtLsdbChecksum
OBJECT-TYPE
This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connec- tionless datagrams; it is commonly referred to as the Fletcher checksum.
1.3.6.1.4.1.1991.1.2.4.10.1.1.7Integer32read-onlycurrent
snOspfExtLsdbAdvertisement
OBJECT-TYPE
The entire Link State Advertisement, including its header.
1.3.6.1.4.1.1991.1.2.4.10.1.1.8OCTET STRING (SIZE(36))read-onlycurrent
snOspfAreaStatus
OBJECT-IDENTITY
1.3.6.1.4.1.1991.1.2.4.11
snOspfAreaStatusTable
OBJECT-TYPE
Information describing the configured parameters and cumulative statistics of the router's attached areas.
1.3.6.1.4.1.1991.1.2.4.11.1not-accessiblecurrent
snOspfAreaStatusEntry
OBJECT-TYPE
Information describing the configured parameters and cumulative statistics of one of the router's attached areas.
1.3.6.1.4.1.1991.1.2.4.11.1.1not-accessiblecurrent
snOspfAreaStatusEntryIndex
OBJECT-TYPE
The table entry index of this Area.
1.3.6.1.4.1.1991.1.2.4.11.1.1.1Integer32read-onlycurrent
snOspfAreaStatusAreaId
OBJECT-TYPE
A 32-bit integer uniquely identifying an area. Area ID 0.0.0.0 is used for the OSPF backbone.
1.3.6.1.4.1.1991.1.2.4.11.1.1.2AreaIDread-onlycurrent
snOspfAreaStatusImportASExtern
OBJECT-TYPE
The area's support for importing AS external link- state advertisements.
1.3.6.1.4.1.1991.1.2.4.11.1.1.3Integer32read-onlycurrent
snOspfAreaStatusStubMetric
OBJECT-TYPE
The metric value applied at the default type of service(ospfMetric). By default, this equals the least metric at the type of service among the interfaces to other areas. This Object exist if only if the value of snOspfAreaSummary is snOspfAreaSummary(2); Otherwise, an SNMP_GET/GET_NEXT attempt of this Object will return NO_SUCH_NAME.
1.3.6.1.4.1.1991.1.2.4.11.1.1.4BigMetricread-onlycurrent
snOspfAreaStatusSpfRuns
OBJECT-TYPE
The number of times that the intra-area route table has been calculated using this area's link-state database. This is typically done using Dijkstra's algorithm.
1.3.6.1.4.1.1991.1.2.4.11.1.1.5Counter32read-onlycurrent
snOspfAreaStatusAreaBdrRtrCount
OBJECT-TYPE
The total number of area border routers reachable within this area. This is initially zero, and is calculated in each SPF Pass.
1.3.6.1.4.1.1991.1.2.4.11.1.1.6Gauge32read-onlycurrent
snOspfAreaStatusASBdrRtrCount
OBJECT-TYPE
The total number of Autonomous System border routers reachable within this area. This is initially zero, and is calculated in each SPF Pass.
1.3.6.1.4.1.1991.1.2.4.11.1.1.7Gauge32read-onlycurrent
snOspfAreaStatusLSACount
OBJECT-TYPE
The total number of link-state advertisements in this area's link-state database, excluding AS External LSA's.
1.3.6.1.4.1.1991.1.2.4.11.1.1.8Gauge32read-onlycurrent
snOspfAreaStatusLSACksumSum
OBJECT-TYPE
The 32-bit unsigned sum of the link-state advertisements' LS checksums contained in this area's link-state database. This sum excludes external (LS type 5) link-state advertisements. The sum can be used to determine if there has been a change in a router's link state database, and to compare the link-state database of two routers.
1.3.6.1.4.1.1991.1.2.4.11.1.1.9Integer32read-onlycurrent
snOspfAreaStatusAreaIdFormat
OBJECT-TYPE
This object is used to specify whether AreaId is represented as IP Address or an Integer. The values that can be written are: integer(0).....as an integer. ipAddress(1)...as IP Address.
1.3.6.1.4.1.1991.1.2.4.11.1.1.10INTEGER {integer(0), ipAddress(1)}read-onlycurrent
snOspfIfStatus
OBJECT-IDENTITY
1.3.6.1.4.1.1991.1.2.4.12
snOspfIfStatusTable
OBJECT-TYPE
The OSPF Interface Status Table describes the interfaces from the viewpoint of OSPF.
1.3.6.1.4.1.1991.1.2.4.12.1not-accessiblecurrent
snOspfIfStatusEntry
OBJECT-TYPE
The OSPF Interface Entry describes one interface from the viewpoint of OSPF.
1.3.6.1.4.1.1991.1.2.4.12.1.1not-accessiblecurrent
snOspfIfStatusEntryIndex
OBJECT-TYPE
The table entry index of this Area.
1.3.6.1.4.1.1991.1.2.4.12.1.1.1Integer32read-onlycurrent
snOspfIfStatusPort
OBJECT-TYPE
The physical router port of this OSPF interface.
1.3.6.1.4.1.1991.1.2.4.12.1.1.2Integer32read-onlycurrent
snOspfIfStatusIpAddress
OBJECT-TYPE
The IP address of this OSPF interface.
1.3.6.1.4.1.1991.1.2.4.12.1.1.3IpAddressread-onlycurrent
snOspfIfStatusAreaId
OBJECT-TYPE
A 32-bit integer uniquely identifying the area to which the interface connects. Area ID 0.0.0.0 is used for the OSPF backbone.
1.3.6.1.4.1.1991.1.2.4.12.1.1.4AreaIDread-onlycurrent
snOspfIfStatusType
OBJECT-TYPE
The OSPF interface type. By way of a default, this field may be intuited from the corresponding value of ifType. Broadcast LANs, such as Ethernet and IEEE 802.5, take the value 'broadcast', X.25, Frame Relay, and similar technologies take the value 'nbma', and links that are definitively point to point take the value 'pointToPoint'.
1.3.6.1.4.1.1991.1.2.4.12.1.1.5INTEGER {broadcast(1), nbma(2), pointToPoint(3)}read-onlycurrent
snOspfIfStatusAdminStat
OBJECT-TYPE
The OSPF interface's administrative status. The value 'enabled' denotes that neighbor relationships may be formed on the interface, and the interface will be advertised as an internal route to some area. The value 'disabled' denotes that the interface is external to OSPF.
1.3.6.1.4.1.1991.1.2.4.12.1.1.6RtrStatusread-onlycurrent
snOspfIfStatusRtrPriority
OBJECT-TYPE
The priority of this interface. Used in multi-access networks, this field is used in the designated router election algorithm. The value 0 signifies that the router is not eligible to become the designated router on this particular network. In the event of a tie in this value, routers will use their router id as a tie breaker.
1.3.6.1.4.1.1991.1.2.4.12.1.1.7DesignatedRouterPriorityread-onlycurrent
snOspfIfStatusTransitDelay
OBJECT-TYPE
The estimated number of seconds it takes to transmit a link- state update packet over this interface.
1.3.6.1.4.1.1991.1.2.4.12.1.1.8UpToMaxAgeread-onlycurrent
snOspfIfStatusRetransInterval
OBJECT-TYPE
The number of seconds between link-state advertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database description and link-state request packets.
1.3.6.1.4.1.1991.1.2.4.12.1.1.9UpToMaxAgeread-onlycurrent
snOspfIfStatusHelloInterval
OBJECT-TYPE
The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for all routers attached to a common network.
1.3.6.1.4.1.1991.1.2.4.12.1.1.10HelloRangeread-onlycurrent
snOspfIfStatusRtrDeadInterval
OBJECT-TYPE
The number of seconds that a router's Hello packets have not been seen before it's neighbors declare the router down. This should be some multiple of the Hello interval. This value must be the same for all routers attached to a common network.
1.3.6.1.4.1.1991.1.2.4.12.1.1.11PositiveIntegerread-onlycurrent
snOspfIfStatusState
OBJECT-TYPE
The OSPF Interface State.
1.3.6.1.4.1.1991.1.2.4.12.1.1.12INTEGER {down(1), loopback(2), waiting(3), pointToPoint(4), designatedRouter(5), backupDesignatedRouter(6), otherDesignatedRouter(7)}read-onlycurrent
snOspfIfStatusDesignatedRouter
OBJECT-TYPE
The IP Address of the Designated Router.
1.3.6.1.4.1.1991.1.2.4.12.1.1.13IpAddressread-onlycurrent
snOspfIfStatusBackupDesignatedRouter
OBJECT-TYPE
The IP Address of the Backup Designated Router.
1.3.6.1.4.1.1991.1.2.4.12.1.1.14IpAddressread-onlycurrent
snOspfIfStatusEvents
OBJECT-TYPE
The number of times this OSPF interface has changed its state, or an error has occurred.
1.3.6.1.4.1.1991.1.2.4.12.1.1.15Counter32read-onlycurrent
snOspfIfStatusAuthType
OBJECT-TYPE
The authentication type specified for an interface. Additional authentication types may be assigned locally on a per interface basis.
1.3.6.1.4.1.1991.1.2.4.12.1.1.16Integer32read-onlycurrent
snOspfIfStatusAuthKey
OBJECT-TYPE
The Authentication Key. If the Area's Authorization Type is simplePassword, and the key length is shorter than 8 octets, the agent will left adjust and zero fill to 8 octets. When read, snOspfIfStatusAuthKey always returns an Octet String of length zero.
1.3.6.1.4.1.1991.1.2.4.12.1.1.17OCTET STRING (SIZE(0..8))read-onlycurrent
snOspfIfStatusMetricValue
OBJECT-TYPE
The metric of using this type of service on this interface. The default value of the TOS 0 Metric is 10^8 / ifSpeed.
1.3.6.1.4.1.1991.1.2.4.12.1.1.18Metricread-onlycurrent
snOspfIfStatusMd5AuthKeyId
OBJECT-TYPE
The md5 authentication key ID. If the snOspfVirtIfAuthType is set to md5, the value of snOspfIfMd5AuthKeyId must be (1 to 255). This field identifies the algorithm and secret key used to create the message digest appended to the OSPF packet. Key Identifiers are unique per-interface (or equivalently, per-subnet).
1.3.6.1.4.1.1991.1.2.4.12.1.1.19INTEGER (0..255)read-onlycurrent
snOspfIfStatusMd5AuthKey
OBJECT-TYPE
The MD5 Authentication Key. If the Area's Authorization Type is md5, and the key length is shorter than 16 octets, the agent will left adjust and zero fill to 16 octets. When read, snOspfIfMd5AuthKey always returns an Octet String of length zero.
1.3.6.1.4.1.1991.1.2.4.12.1.1.20OCTET STRING (SIZE(0..16))read-onlycurrent
snOspfIfStatusMd5ActivationWaitTime
OBJECT-TYPE
The md5 authentication key activation wait time is specified in second and the maximum wait time is 14400 seconds (4 hours).
1.3.6.1.4.1.1991.1.2.4.12.1.1.21INTEGER (0..14400)read-onlycurrent
snOspfIfStatusAreaIdFormat
OBJECT-TYPE
This object is used to specify whether AreaId is represented as IP Address or an Integer. The values that can be written are: integer(0).....as an integer. ipAddress(1)...as IP Address.
1.3.6.1.4.1.1991.1.2.4.12.1.1.22INTEGER {integer(0), ipAddress(1)}read-onlycurrent
snOspfVirtIfStatus
OBJECT-IDENTITY
1.3.6.1.4.1.1991.1.2.4.13
snOspfVirtIfStatusTable
OBJECT-TYPE
Information about this router's virtual interfaces.
1.3.6.1.4.1.1991.1.2.4.13.1not-accessiblecurrent
snOspfVirtIfStatusEntry
OBJECT-TYPE
Information about a single Virtual Interface.
1.3.6.1.4.1.1991.1.2.4.13.1.1not-accessiblecurrent
snOspfVirtIfStatusEntryIndex
OBJECT-TYPE
The table entry index of this Area.
1.3.6.1.4.1.1991.1.2.4.13.1.1.1Integer32read-onlycurrent
snOspfVirtIfStatusAreaID
OBJECT-TYPE
The Transit Area that the Virtual Link traverses. By definition, this is not 0.0.0.0
1.3.6.1.4.1.1991.1.2.4.13.1.1.2AreaIDread-onlycurrent
snOspfVirtIfStatusNeighbor
OBJECT-TYPE
The Router ID of the Virtual Neighbor.
1.3.6.1.4.1.1991.1.2.4.13.1.1.3RouterIDread-onlycurrent
snOspfVirtIfStatusTransitDelay
OBJECT-TYPE
The estimated number of seconds it takes to transmit a link- state update packet over this interface.
1.3.6.1.4.1.1991.1.2.4.13.1.1.4UpToMaxAgeread-onlycurrent
snOspfVirtIfStatusRetransInterval
OBJECT-TYPE
The number of seconds between link-state advertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database description and link-state request packets. This value should be well over the expected round-trip time.
1.3.6.1.4.1.1991.1.2.4.13.1.1.5UpToMaxAgeread-onlycurrent
snOspfVirtIfStatusHelloInterval
OBJECT-TYPE
The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for the virtual neighbor.
1.3.6.1.4.1.1991.1.2.4.13.1.1.6HelloRangeread-onlycurrent
snOspfVirtIfStatusRtrDeadInterval
OBJECT-TYPE
The number of seconds that a router's Hello packets have not been seen before it's neighbors declare the router down. This should be some multiple of the Hello interval. This value must be the same for the virtual neighbor.
1.3.6.1.4.1.1991.1.2.4.13.1.1.7PositiveIntegerread-onlycurrent
snOspfVirtIfStatusState
OBJECT-TYPE
The OSPF virtual interfaces states.
1.3.6.1.4.1.1991.1.2.4.13.1.1.8INTEGER {down(1), pointToPoint(4)}read-onlycurrent
snOspfVirtIfStatusEvents
OBJECT-TYPE
The number of state changes or error events on this Virtual Link.
1.3.6.1.4.1.1991.1.2.4.13.1.1.9Counter32read-onlycurrent
snOspfVirtIfStatusAuthType
OBJECT-TYPE
The authentication type specified for an interface. Additional authentication types may be assigned locally on a per interface basis.
1.3.6.1.4.1.1991.1.2.4.13.1.1.10Integer32read-onlycurrent
snOspfVirtIfStatusAuthKey
OBJECT-TYPE
If Authentication Type is simplePassword, the device will left adjust and zero fill to 8 octets. When read, snOspfVifAuthKey always returns a string of length zero.
1.3.6.1.4.1.1991.1.2.4.13.1.1.11OCTET STRING (SIZE(0..8))read-onlycurrent
snOspfVirtIfStatusMd5AuthKeyId
OBJECT-TYPE
The md5 authentication key ID. If the snOspfVirtIfAuthType is set to md5, the value of snOspfVirtIfMd5AuthKeyId must be (1 to 255). This field identifies the algorithm and secret key used to create the message digest appended to the OSPF packet. Key Identifiers are unique per-interface (or equivalently, per-subnet).
1.3.6.1.4.1.1991.1.2.4.13.1.1.12INTEGER (0..255)read-onlycurrent
snOspfVirtIfStatusMd5AuthKey
OBJECT-TYPE
The MD5 Authentication Key. If the Area's Authorization Type is md5, and the key length is shorter than 16 octets, the agent will left adjust and zero fill to 16 octets. When read, snOspfIfMd5AuthKey always returns an Octet String of length zero.
1.3.6.1.4.1.1991.1.2.4.13.1.1.13OCTET STRING (SIZE(0..16))read-onlycurrent
snOspfVirtIfStatusMd5ActivationWaitTime
OBJECT-TYPE
The md5 authentication key activation wait time is specified in second and the maximum wait time is 14400 seconds (4 hours).
1.3.6.1.4.1.1991.1.2.4.13.1.1.14INTEGER (0..14400)read-onlycurrent
snOspfVirtIfStatusAreaIdFormat
OBJECT-TYPE
This object is used to specify whether AreaId is represented as IP Address or an Integer. The values that can be written are: integer(0).....as an integer. ipAddress(1)...as IP Address.
1.3.6.1.4.1.1991.1.2.4.13.1.1.15INTEGER {integer(0), ipAddress(1)}read-onlycurrent
snOspfRoutingInfo
OBJECT-IDENTITY
1.3.6.1.4.1.1991.1.2.4.14
snOspfRoutingInfoTable
OBJECT-TYPE
Information about this router's routing information.
1.3.6.1.4.1.1991.1.2.4.14.1not-accessiblecurrent
snOspfRoutingInfoEntry
OBJECT-TYPE
Information about a single ABR/ASBR Routing entry.
1.3.6.1.4.1.1991.1.2.4.14.1.1not-accessiblecurrent
snOspfRoutingInfoIndex
OBJECT-TYPE
The table entry index of this Routing entry.
1.3.6.1.4.1.1991.1.2.4.14.1.1.1Integer32read-onlycurrent
snOspfRoutingInfoRouterID
OBJECT-TYPE
The Router ID of the destination router.
1.3.6.1.4.1.1991.1.2.4.14.1.1.2RouterIDread-onlycurrent
snOspfRoutingInfoRouterType
OBJECT-TYPE
The Router type of the destination router as the following: abr (1) -- area border router. asbr (2) -- autonomous sytem border router. abrANDasbr(3) -- area border and autonomous system border router.
1.3.6.1.4.1.1991.1.2.4.14.1.1.3INTEGER {abr(1), asbr(2), abrANDasbr(3)}read-onlycurrent
snOspfRoutingInfoNextHopRouterID
OBJECT-TYPE
The router ID of the next hop destination router.
1.3.6.1.4.1.1991.1.2.4.14.1.1.4RouterIDread-onlycurrent
snOspfRoutingInfoOutgoingInterface
OBJECT-TYPE
The outgoing interface of the destination router.
1.3.6.1.4.1.1991.1.2.4.14.1.1.5Integer32read-onlycurrent
snOspfTrapControl
OBJECT-IDENTITY
1.3.6.1.4.1.1991.1.2.4.15
snOspfSetTrap
OBJECT-TYPE
A four-octet string serving as a bit map for the trap events defined by the OSPF traps. This object is used to enable and disable specific OSPF traps where a 1 in the bit field represents enabled. The right-most bit (least significant) represents trap 0.
1.3.6.1.4.1.1991.1.2.4.15.1OCTET STRING (SIZE(4))read-writecurrent
snOspfConfigErrorType
OBJECT-TYPE
Potential types of configuration conflicts. Used by the ospfConfigError and ospfConfigVir- tError traps.
1.3.6.1.4.1.1991.1.2.4.15.2INTEGER {unUsed(0), badVersion(1), areaMismatch(2), unknownNbmaNbr(3), unknownVirtualNbr(4), authTypeMismatch(5), authFailure(6), netMaskMismatch(7), helloIntervalMismatch(8), deadIntervalMismatch(9), optionMismatch(10)}read-onlycurrent
snOspfPacketType
OBJECT-TYPE
OSPF packet types.
1.3.6.1.4.1.1991.1.2.4.15.3INTEGER {unUsed(0), hello(1), dbDescript(2), lsReq(3), lsUpdate(4), lsAck(5)}read-onlycurrent
snOspfPacketSrc
OBJECT-TYPE
The IP address of an inbound packet that can- not be identified by a neighbor instance.
1.3.6.1.4.1.1991.1.2.4.15.4IpAddressread-onlycurrent
snOspfTrapsGenerationMode
OBJECT-TYPE
Indicates if the generation of any OSPF traps is permitted on the router. The value 'enabled' denotes that the OSPF Traps can be generated by the router; 'disabled' denotes that the OSPF Traps can not be generated by the router even when snOspfSetTrap indicates the generation of specific OSPF Traps. This object provides global control on the generation of ospf traps.
1.3.6.1.4.1.1991.1.2.4.15.5RtrStatusread-writecurrent