MIBs Depot

FOUNDRY-SN-IP-MIB

Registered at
1.3.6.1.4.1.1991.1.2.2
1.3.6.1.4.1.1991.1.2.3.1
1.3.6.1.4.1.1991.1.2.3.9
1.3.6.1.4.1.1991.1.2.5.1
1.3.6.1.4.1.1991.1.2.7.1
1.3.6.1.4.1.1991.1.2.7.2
1.3.6.1.4.1.1991.1.2.8.1
1.3.6.1.4.1.1991.1.2.9.1
1.3.6.1.4.1.1991.1.2.9.2
Last updated
2010-06-02 00:00
Organization
Brocade Communications Systems, Inc.
Revisions
2010-06-02 00:00, 2009-09-30 00:00
Namespace
extreme
Source file
FOUNDRY-SN-IP-MIB
Digest
sha256:6525618c7f14e69dc8535b0ab3d5f900164955b3a05dbb30c13e0c4179e9edb2

Description

Copyright 1996-2010 Brocade Communications Systems, Inc. All rights reserved. This Brocade Communications Systems SNMP Management Information Base Specification embodies Brocade Communications Systems' confidential and proprietary intellectual property. Brocade Communications Systems retains all title and ownership in the Specification, including any revisions. This Specification is supplied AS IS, and Brocade Communications Systems makes no warranty, either express or implied, as to the use, operation, condition, or performance of the specification, and any unintended consequence it may on the user environment.

Contact

Technical Support Center 130 Holger Way, San Jose, CA 95134 Email: ipsupport@brocade.com Phone: 1-800-752-8061 URL: www.brocade.com

Imports

FromSymbols
FOUNDRY-SN-AGENT-MIBDisplayString
FOUNDRY-SN-ROOT-MIBrouter, snDvmrp, snFsrp, snGblRt, snLoopbackIf, snPim, snRip
FOUNDRY-SN-SWITCH-GROUP-MIBPortMask
IF-MIBInterfaceIndex, InterfaceIndexOrZero, ifIndex
INET-ADDRESS-MIBInetAddressType
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP
SNMPv2-SMICounter32, Counter64, Integer32, IpAddress, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, iso
SNMPv2-TCDisplayString, TEXTUAL-CONVENTION

Imported by

2 module(s) in this corpus import this one.

Load order

Every file a consumer needs in order to load this module, dependencies first.

FOUNDRY-SN-AGENT-MIB
FOUNDRY-SN-IP-MIB
FOUNDRY-SN-ROOT-MIB
FOUNDRY-SN-SWITCH-GROUP-MIB
HCNUM-TC
IANAifType-MIB
IF-MIB
INET-ADDRESS-MIB
SNMPv2-CONF
SNMPv2-MIB
SNMPv2-SMI
SNMPv2-TC

Under this module's arcs

Where the registration tree carries on below this module.

ArcNameModule
1.3.6.1.4.1.1991.1.2.2.15snAgAclFOUNDRY-SN-IP-ACL-MIB

Textual conventions

NameOIDSyntaxAccessStatus
Action
TEXTUAL-CONVENTION
Represents a action value such as deny or permit.
current
ClearStatus
TEXTUAL-CONVENTION
Clear Status Values
current
Metric
TEXTUAL-CONVENTION
The OSPF Metric is defined as an unsigned value in the range
current
PortIndex
TEXTUAL-CONVENTION
The bits 0-7 = port number. The bits 8-15 = slot number (slot for chassis only). ve port format bits 16-24 = 0x01, bits 0-15 = ve number loopback port format bits 16-24 = 0x02, bits 0-15= lb number
current
RowSts
TEXTUAL-CONVENTION
Row Creation/Deletion Values
current
RtrStatus
TEXTUAL-CONVENTION
RtrStatus Values
current

Objects

NameOIDSyntaxAccessStatus
snRtIpGeneral
OBJECT-IDENTITY
1.3.6.1.4.1.1991.1.2.2.1
snRtClearArpCache
OBJECT-TYPE
clear(1) will clear arp cache table.
1.3.6.1.4.1.1991.1.2.2.1.1ClearStatusread-writecurrent
snRtClearIpCache
OBJECT-TYPE
clear(1) will clear ip route cache table.
1.3.6.1.4.1.1991.1.2.2.1.2ClearStatusread-writecurrent
snRtClearIpRoute
OBJECT-TYPE
clear(1) will clear ip route table.
1.3.6.1.4.1.1991.1.2.2.1.3ClearStatusread-writecurrent
snRtBootpServer
OBJECT-TYPE
IP address of bootp server to which bootp packet need to be relayed.
1.3.6.1.4.1.1991.1.2.2.1.4IpAddressread-writedeprecated
snRtBootpRelayMax
OBJECT-TYPE
Maximum number of hop the bootp packet should travel.
1.3.6.1.4.1.1991.1.2.2.1.5INTEGER (1..15)read-writecurrent
snRtArpAge
OBJECT-TYPE
The time in minutes an ARP entry can be valid without relearning. 0 - Don't not age.
1.3.6.1.4.1.1991.1.2.2.1.6INTEGER (0..240)read-writecurrent
snRtIpIrdpEnable
OBJECT-TYPE
Perform router advertisement on this box.
1.3.6.1.4.1.1991.1.2.2.1.7RtrStatusread-writecurrent
snRtIpLoadShare
OBJECT-TYPE
If more than one route available, use them to share load.
1.3.6.1.4.1.1991.1.2.2.1.8RtrStatusread-writecurrent
snRtIpProxyArp
OBJECT-TYPE
Enable/disable proxy arp function in the box.
1.3.6.1.4.1.1991.1.2.2.1.9RtrStatusread-writecurrent
snRtIpRarp
OBJECT-TYPE
Enable/disable RARP server.
1.3.6.1.4.1.1991.1.2.2.1.10RtrStatusread-writecurrent
snRtIpTtl
OBJECT-TYPE
The time to live value to be used in IP header of IP packet generated by the box.
1.3.6.1.4.1.1991.1.2.2.1.11INTEGER (1..255)read-writecurrent
snRtIpSetAllPortConfig
OBJECT-TYPE
The value of this object is an index number of a snRtIpPortConfigTable row (i.e. snRtIpPortConfigPortIndex), which is the selected row to copy all of its read-writable data (i.e. snRtIpPortMtu and snRtIpPortEncap) to the rest of the rows in snRtIpPortConfigTable. Note: prior setting this object, all the intended data of the given row of the table must be set. Otherwise, the current data of the row will be used to set the entire ip interface configuration table. The previous setting will be overwritten by the new one.
1.3.6.1.4.1.1991.1.2.2.1.12Integer32read-writecurrent
snRtIpFwdCacheMaxEntries
OBJECT-TYPE
The maximum number of ip forwarding table entries.
1.3.6.1.4.1.1991.1.2.2.1.13Integer32read-onlycurrent
snRtIpFwdCacheCurEntries
OBJECT-TYPE
The current number of ip forwarding table entries.
1.3.6.1.4.1.1991.1.2.2.1.14Integer32read-onlycurrent
snRtIpMaxStaticRouteEntries
OBJECT-TYPE
The maximum number of static route entries in the static route table.
1.3.6.1.4.1.1991.1.2.2.1.15Integer32read-onlycurrent
snRtIpDirBcastFwd
OBJECT-TYPE
Enable/Disable directed broadcast forwarding.
1.3.6.1.4.1.1991.1.2.2.1.16RtrStatusread-writecurrent
snRtIpLoadShareNumOfPaths
OBJECT-TYPE
Number of routes are used to share load.
1.3.6.1.4.1.1991.1.2.2.1.17Integer32read-writecurrent
snRtIpLoadShareMaxPaths
OBJECT-TYPE
Maximum number of routes can be configured to share load.
1.3.6.1.4.1.1991.1.2.2.1.18Integer32read-onlycurrent
snRtIpLoadShareMinPaths
OBJECT-TYPE
Minimum number of routes can be configured to share load.
1.3.6.1.4.1.1991.1.2.2.1.19Integer32read-onlycurrent
snRtIpProtocolRouterId
OBJECT-TYPE
Router Id for all IP Protocols.
1.3.6.1.4.1.1991.1.2.2.1.20IpAddressread-writecurrent
snRtIpSourceRoute
OBJECT-TYPE
Enable/Disable source routing support, ability to drop the source routing packets.
1.3.6.1.4.1.1991.1.2.2.1.21RtrStatusread-writecurrent
snRtIpStaticRouteTable
OBJECT-TYPE
IP static/default route table.
1.3.6.1.4.1.1991.1.2.2.2not-accessiblecurrent
snRtIpStaticRouteEntry
OBJECT-TYPE
An entry in the IP static route table.
1.3.6.1.4.1.1991.1.2.2.2.1not-accessiblecurrent
snRtIpStaticRouteIndex
OBJECT-TYPE
The table index for a static route entry.
1.3.6.1.4.1.1991.1.2.2.2.1.1Integer32read-onlycurrent
snRtIpStaticRouteDest
OBJECT-TYPE
Destination IP address. 0.0.0.0 for default route.
1.3.6.1.4.1.1991.1.2.2.2.1.2IpAddressread-writecurrent
snRtIpStaticRouteMask
OBJECT-TYPE
Subnet mask associated with the destination IP address. 0.0.0.0 for default route mask.
1.3.6.1.4.1.1991.1.2.2.2.1.3IpAddressread-writecurrent
snRtIpStaticRouteNextHop
OBJECT-TYPE
IP address of next hop router that is located on one of the directly attached IP subnet.
1.3.6.1.4.1.1991.1.2.2.2.1.4IpAddressread-writecurrent
snRtIpStaticRouteMetric
OBJECT-TYPE
The metrics to next hop router.
1.3.6.1.4.1.1991.1.2.2.2.1.5Integer32read-writecurrent
snRtIpStaticRouteRowStatus
OBJECT-TYPE
To create or delete a static route entry.
1.3.6.1.4.1.1991.1.2.2.2.1.6RowStsread-writecurrent
snRtIpStaticRouteDistance
OBJECT-TYPE
Administration distance.
1.3.6.1.4.1.1991.1.2.2.2.1.7INTEGER (1..255)read-writecurrent
snRtIpFilterTable
OBJECT-TYPE
IP filter table.
1.3.6.1.4.1.1991.1.2.2.3not-accessiblecurrent
snRtIpFilterEntry
OBJECT-TYPE
An entry in the IP filter table.
1.3.6.1.4.1.1991.1.2.2.3.1not-accessiblecurrent
snRtIpFilterIndex
OBJECT-TYPE
The table index for a filter entry.
1.3.6.1.4.1.1991.1.2.2.3.1.1Integer32read-onlycurrent
snRtIpFilterAction
OBJECT-TYPE
Action to take if the ip packet match with this filter.
1.3.6.1.4.1.1991.1.2.2.3.1.2INTEGER {deny(0), permit(1), qosEnabled(2)}read-writecurrent
snRtIpFilterProtocol
OBJECT-TYPE
Transport protocol. 0 means don't care
1.3.6.1.4.1.1991.1.2.2.3.1.3INTEGER (0..255)read-writecurrent
snRtIpFilterSourceIp
OBJECT-TYPE
Source IP address.
1.3.6.1.4.1.1991.1.2.2.3.1.4IpAddressread-writecurrent
snRtIpFilterSourceMask
OBJECT-TYPE
Source IP subnet mask.
1.3.6.1.4.1.1991.1.2.2.3.1.5IpAddressread-writecurrent
snRtIpFilterDestIp
OBJECT-TYPE
Destination IP address.
1.3.6.1.4.1.1991.1.2.2.3.1.6IpAddressread-writecurrent
snRtIpFilterDestMask
OBJECT-TYPE
Destination IP subnet mask.
1.3.6.1.4.1.1991.1.2.2.3.1.7IpAddressread-writecurrent
snRtIpFilterOperator
OBJECT-TYPE
Type of comparison to perform. for now, this only applys to tcp or udp to compare the port number
1.3.6.1.4.1.1991.1.2.2.3.1.8INTEGER {greater(1), equal(2), less(3), notEqual(4)}read-writecurrent
snRtIpFilterOperand
OBJECT-TYPE
For now this only refers to transport protocol port number. 0 means NA
1.3.6.1.4.1.1991.1.2.2.3.1.9INTEGER (0..65535)read-writecurrent
snRtIpFilterRowStatus
OBJECT-TYPE
To create or delete a filter entry.
1.3.6.1.4.1.1991.1.2.2.3.1.10RowStsread-writecurrent
snRtIpFilterEstablished
OBJECT-TYPE
Enable/Disable the filtering of established TCP packets of which the ACK or RESET flag is on. This additional filter only applies to TCP transport protocol.
1.3.6.1.4.1.1991.1.2.2.3.1.11RtrStatusread-writecurrent
snRtIpFilterQosPriority
OBJECT-TYPE
The router L4 Qos Priority values are: low(0) -- low prority high(1) -- high prority. The Priority values are: level0(0), level1(1), level2(2), level3(3), level4(4), level5(5), level6(6), level7(7)
1.3.6.1.4.1.1991.1.2.2.3.1.12INTEGER {level0(0), level1(1), level2(2), level3(3), level4(4), level5(5), level6(6), level7(7)}read-writecurrent
snRtIpRarpTable
OBJECT-TYPE
IP RARP table.
1.3.6.1.4.1.1991.1.2.2.4not-accessiblecurrent
snRtIpRarpEntry
OBJECT-TYPE
An entry in the IP Rarp table.
1.3.6.1.4.1.1991.1.2.2.4.1not-accessiblecurrent
snRtIpRarpIndex
OBJECT-TYPE
The table index for a Rarp entry.
1.3.6.1.4.1.1991.1.2.2.4.1.1INTEGER (1..16)read-onlycurrent
snRtIpRarpMac
OBJECT-TYPE
The Mac address for a Rarp entry.
1.3.6.1.4.1.1991.1.2.2.4.1.2OCTET STRING (SIZE(6))read-writecurrent
snRtIpRarpIp
OBJECT-TYPE
The IP address for a Rarp entry.
1.3.6.1.4.1.1991.1.2.2.4.1.3IpAddressread-writecurrent
snRtIpRarpRowStatus
OBJECT-TYPE
To create or delete a Rarp entry.
1.3.6.1.4.1.1991.1.2.2.4.1.4RowStsread-writecurrent
snRtStaticArpTable
OBJECT-TYPE
IP static arp table.
1.3.6.1.4.1.1991.1.2.2.5not-accessiblecurrent
snRtStaticArpEntry
OBJECT-TYPE
An entry in the IP static arp table.
1.3.6.1.4.1.1991.1.2.2.5.1not-accessiblecurrent
snRtStaticArpIndex
OBJECT-TYPE
The table index for a static arp entry.
1.3.6.1.4.1.1991.1.2.2.5.1.1INTEGER (1..16)read-onlycurrent
snRtStaticArpIp
OBJECT-TYPE
The IP address for a static arp entry.
1.3.6.1.4.1.1991.1.2.2.5.1.2IpAddressread-writecurrent
snRtStaticArpMac
OBJECT-TYPE
The Mac address for a static arp entry.
1.3.6.1.4.1.1991.1.2.2.5.1.3OCTET STRING (SIZE(6))read-writecurrent
snRtStaticArpPort
OBJECT-TYPE
The port index for a static arp entry.
1.3.6.1.4.1.1991.1.2.2.5.1.4PortIndexread-writecurrent
snRtStaticArpRowStatus
OBJECT-TYPE
To create or delete a Static Arp entry.
1.3.6.1.4.1.1991.1.2.2.5.1.5RowStsread-writecurrent
snRtIpPortAddrTable
OBJECT-TYPE
IP port address table.
1.3.6.1.4.1.1991.1.2.2.6not-accessibledeprecated
snRtIpPortAddrEntry
OBJECT-TYPE
An entry in the IP Port Address table.
1.3.6.1.4.1.1991.1.2.2.6.1not-accessibledeprecated
snRtIpPortAddrPortIndex
OBJECT-TYPE
The port index for port address entry.
1.3.6.1.4.1.1991.1.2.2.6.1.1PortIndexread-onlydeprecated
snRtIpPortAddress
OBJECT-TYPE
The port IP address.
1.3.6.1.4.1.1991.1.2.2.6.1.2IpAddressread-onlydeprecated
snRtIpPortSubnetMask
OBJECT-TYPE
The port IP address subnet mask.
1.3.6.1.4.1.1991.1.2.2.6.1.3IpAddressread-writedeprecated
snRtIpPortAddrType
OBJECT-TYPE
The port IP address type.
1.3.6.1.4.1.1991.1.2.2.6.1.4INTEGER {primary(1), secondary(2)}read-writedeprecated
snRtIpPortRowStatus
OBJECT-TYPE
To create or delete a port address entry.
1.3.6.1.4.1.1991.1.2.2.6.1.5RowStsread-writedeprecated
snRtIpPortAccessTable
OBJECT-TYPE
IP port access table.
1.3.6.1.4.1.1991.1.2.2.7not-accessibledeprecated
snRtIpPortAccessEntry
OBJECT-TYPE
An entry in the IP Port access table.
1.3.6.1.4.1.1991.1.2.2.7.1not-accessibledeprecated
snRtIpPortAccessPortIndex
OBJECT-TYPE
The port index for port access entry.
1.3.6.1.4.1.1991.1.2.2.7.1.1PortIndexread-onlydeprecated
snRtIpPortAccessDirection
OBJECT-TYPE
The incoming or outgoing check for port access.
1.3.6.1.4.1.1991.1.2.2.7.1.2INTEGER {in(1), out(2)}read-onlydeprecated
snRtIpPortAccessFilters
OBJECT-TYPE
1st octet correspond to 1st filter number and so on.
1.3.6.1.4.1.1991.1.2.2.7.1.3OCTET STRINGread-writedeprecated
snRtIpPortAccessRowStatus
OBJECT-TYPE
To create or delete a port access entry.
1.3.6.1.4.1.1991.1.2.2.7.1.4RowStsread-writedeprecated
snRtIpPortConfigTable
OBJECT-TYPE
IP port Config table.
1.3.6.1.4.1.1991.1.2.2.8not-accessibledeprecated
snRtIpPortConfigEntry
OBJECT-TYPE
An entry in the IP Port Config table.
1.3.6.1.4.1.1991.1.2.2.8.1not-accessibledeprecated
snRtIpPortConfigPortIndex
OBJECT-TYPE
The port index for port config entry.
1.3.6.1.4.1.1991.1.2.2.8.1.1PortIndexread-onlydeprecated
snRtIpPortMtu
OBJECT-TYPE
The maximun transfer unit.
1.3.6.1.4.1.1991.1.2.2.8.1.2INTEGER (576..4470)read-writedeprecated
snRtIpPortEncap
OBJECT-TYPE
Data link encapsulation to be used on the IP frame transmitted on the port.
1.3.6.1.4.1.1991.1.2.2.8.1.3INTEGER {ethernet(1), snap(2), hdlc(3), ppp(4)}read-writedeprecated
snRtIpPortMetric
OBJECT-TYPE
The metric.
1.3.6.1.4.1.1991.1.2.2.8.1.4INTEGER (1..15)read-writedeprecated
snRtIpPortDirBcastFwd
OBJECT-TYPE
Enable/Disable directed broadcast forwarding on the port.
1.3.6.1.4.1.1991.1.2.2.8.1.5RtrStatusread-writedeprecated
snRtBcastFwd
OBJECT-IDENTITY
1.3.6.1.4.1.1991.1.2.2.9
snRtBcastFwdGeneral
OBJECT-IDENTITY
1.3.6.1.4.1.1991.1.2.2.9.1
snRtUdpBcastFwdEnable
OBJECT-TYPE
Enable or disable UDP broadcast forwarding service. When UDP broadcast forwarding is enabled, default entries are added to the UDP broadcast forwarding port table. When it is disabled, UDP broadcast forwarding port table is flushed to empty.
1.3.6.1.4.1.1991.1.2.2.9.1.1RtrStatusread-writecurrent
snRtUdpBcastFwdPort
OBJECT-IDENTITY
1.3.6.1.4.1.1991.1.2.2.9.2
snRtUdpBcastFwdPortTable
OBJECT-TYPE
This table contains a list of UDP port numbers for which forwarding UDP broadcast is enabled.
1.3.6.1.4.1.1991.1.2.2.9.2.1not-accessiblecurrent
snRtUdpBcastFwdPortEntry
OBJECT-TYPE
An entry of the UDP broadcast forwarding port table.
1.3.6.1.4.1.1991.1.2.2.9.2.1.1not-accessiblecurrent
snRtUdpBcastFwdPortIndex
OBJECT-TYPE
The table index for a UDP broadcast forwarding port entry.
1.3.6.1.4.1.1991.1.2.2.9.2.1.1.1INTEGER (1..20)read-onlycurrent
snRtUdpBcastFwdPortNumber
OBJECT-TYPE
UDP port number for which UDP broadcast forwarding is enabled.
1.3.6.1.4.1.1991.1.2.2.9.2.1.1.2INTEGER (1..65535)read-writecurrent
snRtUdpBcastFwdPortRowStatus
OBJECT-TYPE
To create or delete a UDP broadcast forwarding port entry.
1.3.6.1.4.1.1991.1.2.2.9.2.1.1.3RowStsread-writecurrent
snRtUdpBroadcastFwdPortTable
OBJECT-TYPE
This table contains a list of UDP port numbers for which forwarding UDP broadcast is enabled.
1.3.6.1.4.1.1991.1.2.2.9.2.2not-accessiblecurrent
snRtUdpBroadcastFwdPortEntry
OBJECT-TYPE
An entry of the UDP broadcast forwarding port table.
1.3.6.1.4.1.1991.1.2.2.9.2.2.1not-accessiblecurrent
snRtUdpBroadcastFwdPortNumber
OBJECT-TYPE
UDP port number for which UDP broadcast forwarding is enabled.
1.3.6.1.4.1.1991.1.2.2.9.2.2.1.1Integer32not-accessiblecurrent
snRtUdpBroadcastFwdPortRowStatus
OBJECT-TYPE
To create or delete a UDP broadcast forwarding port entry.
1.3.6.1.4.1.1991.1.2.2.9.2.2.1.2RowStsread-writecurrent
snRtUdpHelper
OBJECT-IDENTITY
1.3.6.1.4.1.1991.1.2.2.9.3
snRtUdpHelperTable
OBJECT-TYPE
UDP helper table.
1.3.6.1.4.1.1991.1.2.2.9.3.1not-accessiblecurrent
snRtUdpHelperEntry
OBJECT-TYPE
An entry of the UDP helper table.
1.3.6.1.4.1.1991.1.2.2.9.3.1.1not-accessiblecurrent
snRtUdpHelperPortIndex
OBJECT-TYPE
The port index for a UDP helper entry.
1.3.6.1.4.1.1991.1.2.2.9.3.1.1.1PortIndexread-onlycurrent
snRtUdpHelperIndex
OBJECT-TYPE
The table index for a UDP helper entry.
1.3.6.1.4.1.1991.1.2.2.9.3.1.1.2INTEGER (1..4)read-onlycurrent
snRtUdpHelperAddr
OBJECT-TYPE
The UDP helper address. This is the address that UDP packets will be forwarded. It can be a helper address or a subnet broadcast address. But it cannot be 255.255.255.255 or 0.0.0.0.
1.3.6.1.4.1.1991.1.2.2.9.3.1.1.3IpAddressread-writecurrent
snRtUdpHelperRowStatus
OBJECT-TYPE
To create or delete a UDP helper entry.
1.3.6.1.4.1.1991.1.2.2.9.3.1.1.4RowStsread-writecurrent
snRtUdpIfHelperTable
OBJECT-TYPE
UDP helper table.
1.3.6.1.4.1.1991.1.2.2.9.3.2not-accessiblecurrent
snRtUdpIfHelperEntry
OBJECT-TYPE
An entry of the UDP helper table.
1.3.6.1.4.1.1991.1.2.2.9.3.2.1not-accessiblecurrent
snRtUdpIfHelperPortIndex
OBJECT-TYPE
The port/interface index for a UDP helper entry.
1.3.6.1.4.1.1991.1.2.2.9.3.2.1.1InterfaceIndexnot-accessiblecurrent
snRtUdpIfHelperAddr
OBJECT-TYPE
The UDP helper address. This is the address that UDP packets will be forwarded. It can be a helper address or a subnet broadcast address. But it cannot be 255.255.255.255 or 0.0.0.0.
1.3.6.1.4.1.1991.1.2.2.9.3.2.1.2IpAddressnot-accessiblecurrent
snRtUdpIfHelperAddrType
OBJECT-TYPE
Type of the helper address. It can be unicast or subnet brodcast address.
1.3.6.1.4.1.1991.1.2.2.9.3.2.1.3INTEGER {unicast(1), broabcast(2)}read-writecurrent
snRtUdpIfHelperRowStatus
OBJECT-TYPE
To create or delete a UDP helper entry.
1.3.6.1.4.1.1991.1.2.2.9.3.2.1.4RowStsread-writecurrent
snRtIpTraceRoute
OBJECT-IDENTITY
1.3.6.1.4.1.1991.1.2.2.10
snRtIpTraceRouteGeneral
OBJECT-IDENTITY
1.3.6.1.4.1.1991.1.2.2.10.1
snRtIpTraceRouteTargetAddr
OBJECT-TYPE
Target IP address of which trace route is performed.
1.3.6.1.4.1.1991.1.2.2.10.1.1IpAddressread-writecurrent
snRtIpTraceRouteMinTtl
OBJECT-TYPE
Minimum TTL value carried in the first probe packet. Value 0 cannot be used for SET operations. This value is returned if traceroute is not running within the system.
1.3.6.1.4.1.1991.1.2.2.10.1.2INTEGER (0..255)read-writecurrent
snRtIpTraceRouteMaxTtl
OBJECT-TYPE
Maximum TTL value carried in the last probe packet. Value 0 cannot be used for SET operations. This value is returned if traceroute is not running within the system.
1.3.6.1.4.1.1991.1.2.2.10.1.3INTEGER (0..255)read-writecurrent
snRtIpTraceRouteTimeOut
OBJECT-TYPE
Time out period (in seconds) to wait for the response from the probe packet (i,e, the ICMP packet). Value 0 cannot be used for SET operations. This value is returned if traceroute is not running within the system.
1.3.6.1.4.1.1991.1.2.2.10.1.4INTEGER (0..120)read-writecurrent
snRtIpTraceRouteControl
OBJECT-TYPE
Only 'start' and 'abort' are writable values; 'success', 'failure' and 'inProgress' are readeable (or returned) values. Writing 'start' to this object to initiate the trace route operation. snRtIpTraceRouteDestAddr must have been init- ialized before 'start' is writen. This object will return 'inProgress' after trace route operation has started. During the 'inProgress' state, writing 'abort' to this object will stop the current trace route operation. If the destination address is reached, this object returned 'success'. snRtIpTraceRouteResultTable contains the routes (and the target address) to reach the destination address. If the destination address does not reach, timeout, or ending TTL reached, 'failure' is returned.
1.3.6.1.4.1.1991.1.2.2.10.1.5INTEGER {start(1), abort(2), success(3), failure(4), inProgress(5)}read-writecurrent
snRtIpTraceRouteResult
OBJECT-IDENTITY
1.3.6.1.4.1.1991.1.2.2.10.2
snRtIpTraceRouteResultTable
OBJECT-TYPE
Trace route result table.
1.3.6.1.4.1.1991.1.2.2.10.2.1not-accessiblecurrent
snRtIpTraceRouteResultEntry
OBJECT-TYPE
An entry of the trace route result table.
1.3.6.1.4.1.1991.1.2.2.10.2.1.1not-accessiblecurrent
snRtIpTraceRouteResultIndex
OBJECT-TYPE
The table index for a trace route result entry.
1.3.6.1.4.1.1991.1.2.2.10.2.1.1.1Integer32read-onlycurrent
snRtIpTraceRouteResultAddr
OBJECT-TYPE
The router or the target address of which forms part of the route to reach the destination address.
1.3.6.1.4.1.1991.1.2.2.10.2.1.1.2IpAddressread-onlycurrent
snRtIpTraceRouteResultRoundTripTime1
OBJECT-TYPE
The round trip time between the first probe packet transmitted and the reponse ICMP packet received.
1.3.6.1.4.1.1991.1.2.2.10.2.1.1.3TimeTicksread-onlycurrent
snRtIpTraceRouteResultRoundTripTime2
OBJECT-TYPE
The round trip time between the second probe packet transmitted and the reponse ICMP packet received.
1.3.6.1.4.1.1991.1.2.2.10.2.1.1.4TimeTicksread-onlycurrent
snRtIpFwdCacheTable
OBJECT-TYPE
IP forwarding cache table.
1.3.6.1.4.1.1991.1.2.2.11not-accessiblecurrent
snRtIpFwdCacheEntry
OBJECT-TYPE
An entry in the IP forwarding cache table.
1.3.6.1.4.1.1991.1.2.2.11.1not-accessiblecurrent
snRtIpFwdCacheIndex
OBJECT-TYPE
The table index for a ip forwarding cache table entry.
1.3.6.1.4.1.1991.1.2.2.11.1.1Integer32read-onlycurrent
snRtIpFwdCacheIp
OBJECT-TYPE
The IP address of a station.
1.3.6.1.4.1.1991.1.2.2.11.1.2IpAddressread-onlycurrent
snRtIpFwdCacheMac
OBJECT-TYPE
The Mac address of an IP station.
1.3.6.1.4.1.1991.1.2.2.11.1.3OCTET STRING (SIZE(6))read-onlycurrent
snRtIpFwdCacheNextHopIp
OBJECT-TYPE
The next hop router IP address.
1.3.6.1.4.1.1991.1.2.2.11.1.4IpAddressread-onlycurrent
snRtIpFwdCacheOutgoingPort
OBJECT-TYPE
The outgoing port of which packets will forward to. Return port value of zero to indicate no outgoing port associated to this entry. Non-zero value has the following meanings: The bit 0 to bit 7: port number. The bit 8 to bit 11: slot number. For virtual router interface, slot number is 15, port number is the virtual router port from 1 to 60.
1.3.6.1.4.1.1991.1.2.2.11.1.5INTEGER (0..3900)read-onlycurrent
snRtIpFwdCacheType
OBJECT-TYPE
The 'dynamic' or 'permanent' type for a ip forwarding cache table entry.
1.3.6.1.4.1.1991.1.2.2.11.1.6INTEGER {dynamic(1), permanent(2)}read-onlycurrent
snRtIpFwdCacheAction
OBJECT-TYPE
The action to take.
1.3.6.1.4.1.1991.1.2.2.11.1.7INTEGER {other(1), forward(2), forUs(3), waitForArp(4), complexFilter(5), icmpDeny(6), dropPacket(7)}read-onlycurrent
snRtIpFwdCacheFragCheck
OBJECT-TYPE
Check for fragmentation.
1.3.6.1.4.1.1991.1.2.2.11.1.8INTEGER {disabled(0), enabled(1)}read-onlycurrent
snRtIpFwdCacheSnapHdr
OBJECT-TYPE
Apply SNAP encapsulation.
1.3.6.1.4.1.1991.1.2.2.11.1.9INTEGER {disabled(0), enabled(1)}read-onlycurrent
snRtIpFwdCacheVLanId
OBJECT-TYPE
The VLAN ID for a ip forwarding cache table entry. Return VLAN ID value of zero to indicate no VLAN associated to this entry.
1.3.6.1.4.1.1991.1.2.2.11.1.10Integer32read-onlycurrent
snRtIpFwdCacheOutgoingIf
OBJECT-TYPE
The outgoing interface of which packets will forward to. Return port value of zero to indicate no outgoing port associated to this entry.
1.3.6.1.4.1.1991.1.2.2.11.1.11Integer32read-onlycurrent
snIpAsPathAccessListTable
OBJECT-TYPE
Ip As-Path Access List table.
1.3.6.1.4.1.1991.1.2.2.12not-accessiblecurrent
snIpAsPathAccessListEntry
OBJECT-TYPE
An entry in the Ip As-Path Access List table.
1.3.6.1.4.1.1991.1.2.2.12.1not-accessiblecurrent
snIpAsPathAccessListIndex
OBJECT-TYPE
The table index for a filter entry.
1.3.6.1.4.1.1991.1.2.2.12.1.1Integer32read-onlycurrent
snIpAsPathAccessListSequence
OBJECT-TYPE
The table sequence index for a filter entry.
1.3.6.1.4.1.1991.1.2.2.12.1.2Integer32read-onlycurrent
snIpAsPathAccessListAction
OBJECT-TYPE
Action to take if the bgp address match with this filter.
1.3.6.1.4.1.1991.1.2.2.12.1.3INTEGER {deny(0), permit(1)}read-writecurrent
snIpAsPathAccessListRegExpression
OBJECT-TYPE
Autonomous system in the filter using a regular expression. Each character of the regular expression string is represented by one octet.
1.3.6.1.4.1.1991.1.2.2.12.1.4OCTET STRING (SIZE(0..256))read-writecurrent
snIpAsPathAccessListRowStatus
OBJECT-TYPE
This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid
1.3.6.1.4.1.1991.1.2.2.12.1.5INTEGER {invalid(1), valid(2), delete(3), create(4), modify(5)}read-writecurrent
snIpCommunityListTable
OBJECT-TYPE
Ip Community List table.
1.3.6.1.4.1.1991.1.2.2.13not-accessiblecurrent
snIpCommunityListEntry
OBJECT-TYPE
An entry in the Ip Community List table.
1.3.6.1.4.1.1991.1.2.2.13.1not-accessiblecurrent
snIpCommunityListIndex
OBJECT-TYPE
The table index for a filter entry.
1.3.6.1.4.1.1991.1.2.2.13.1.1Integer32read-onlycurrent
snIpCommunityListSequence
OBJECT-TYPE
The table sequence index for a filter entry.
1.3.6.1.4.1.1991.1.2.2.13.1.2Integer32read-onlycurrent
snIpCommunityListAction
OBJECT-TYPE
Action to take if the bgp address match with this filter.
1.3.6.1.4.1.1991.1.2.2.13.1.3INTEGER {deny(0), permit(1)}read-writecurrent
snIpCommunityListCommNum
OBJECT-TYPE
A number from 1 to 0xFFFFFFFF. There are 20 of them. This integer number is represented by 4 OCTETs.
1.3.6.1.4.1.1991.1.2.2.13.1.4OCTET STRING (SIZE(0..80))read-writecurrent
snIpCommunityListInternet
OBJECT-TYPE
Disabled/Enabled the Internet Community.
1.3.6.1.4.1.1991.1.2.2.13.1.5INTEGER {disabled(0), enabled(1)}read-writecurrent
snIpCommunityListNoAdvertise
OBJECT-TYPE
Do not advertise this route to any peer (internal or external).
1.3.6.1.4.1.1991.1.2.2.13.1.6INTEGER {false(0), true(1)}read-writecurrent
snIpCommunityListNoExport
OBJECT-TYPE
Do not advertise this route to an EBGP peer.
1.3.6.1.4.1.1991.1.2.2.13.1.7INTEGER {false(0), true(1)}read-writecurrent
snIpCommunityListRowStatus
OBJECT-TYPE
This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid
1.3.6.1.4.1.1991.1.2.2.13.1.8INTEGER {invalid(1), valid(2), delete(3), create(4), modify(5)}read-writecurrent
snIpCommunityListLocalAs
OBJECT-TYPE
Send this route to peers in other sub-autonomous systems within the local confederation. Do not advertise this route to an external system.
1.3.6.1.4.1.1991.1.2.2.13.1.9INTEGER {false(0), true(1)}read-writecurrent
snIpPrefixListTable
OBJECT-TYPE
Ip Prefix List table.
1.3.6.1.4.1.1991.1.2.2.14not-accessiblecurrent
snIpPrefixListEntry
OBJECT-TYPE
An entry in the Ip Prefix List table.
1.3.6.1.4.1.1991.1.2.2.14.1not-accessiblecurrent
snIpPrefixListName
OBJECT-TYPE
An octet string of the ip prefix list name, each character of the name is represented by one octet.
1.3.6.1.4.1.1991.1.2.2.14.1.1OCTET STRING (SIZE(0..32))read-onlycurrent
snIpPrefixListSequence
OBJECT-TYPE
The table sequence index for a filter entry.
1.3.6.1.4.1.1991.1.2.2.14.1.2Integer32read-onlycurrent
snIpPrefixListDesc
OBJECT-TYPE
An octet string of the ip prefix list description, each character of the name is represented by one octet.
1.3.6.1.4.1.1991.1.2.2.14.1.3OCTET STRING (SIZE(0..80))read-writecurrent
snIpPrefixListAction
OBJECT-TYPE
Action to take if the ip prefix match with this filter.
1.3.6.1.4.1.1991.1.2.2.14.1.4INTEGER {deny(0), permit(1)}read-writecurrent
snIpPrefixListAddr
OBJECT-TYPE
Prefix IP address.
1.3.6.1.4.1.1991.1.2.2.14.1.5IpAddressread-writecurrent
snIpPrefixListMask
OBJECT-TYPE
Prefix IP mask.
1.3.6.1.4.1.1991.1.2.2.14.1.6IpAddressread-writecurrent
snIpPrefixListGeValue
OBJECT-TYPE
Greater than value.
1.3.6.1.4.1.1991.1.2.2.14.1.7INTEGER (0..32)read-writecurrent
snIpPrefixListLeValue
OBJECT-TYPE
Less than value.
1.3.6.1.4.1.1991.1.2.2.14.1.8INTEGER (0..32)read-writecurrent
snIpPrefixListRowStatus
OBJECT-TYPE
This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid
1.3.6.1.4.1.1991.1.2.2.14.1.9INTEGER {invalid(1), valid(2), delete(3), create(4), modify(5)}read-writecurrent
snIpPrefixListLength
OBJECT-TYPE
Prefix IP mask length.
1.3.6.1.4.1.1991.1.2.2.14.1.10Integer32read-writecurrent
snIpAsPathAccessListStringTable
OBJECT-TYPE
Ip As-Path Access List table, string version.
1.3.6.1.4.1.1991.1.2.2.16not-accessiblecurrent
snIpAsPathAccessListStringEntry
OBJECT-TYPE
An entry in the Ip As-Path Access List table.
1.3.6.1.4.1.1991.1.2.2.16.1not-accessiblecurrent
snIpAsPathAccessListStringName
OBJECT-TYPE
The table index for a filter entry, string version.
1.3.6.1.4.1.1991.1.2.2.16.1.1DisplayString (SIZE(0..32))read-onlycurrent
snIpAsPathAccessListStringSequence
OBJECT-TYPE
The table sequence index for a filter entry.
1.3.6.1.4.1.1991.1.2.2.16.1.2Integer32read-onlycurrent
snIpAsPathAccessListStringAction
OBJECT-TYPE
Action to take if the bgp address match with this filter.
1.3.6.1.4.1.1991.1.2.2.16.1.3INTEGER {deny(0), permit(1)}read-writecurrent
snIpAsPathAccessListStringRegExpression
OBJECT-TYPE
Autonomous system in the filter using a regular expression. Each character of the regular expression string is represented by one octet.
1.3.6.1.4.1.1991.1.2.2.16.1.4DisplayString (SIZE(0..256))read-writecurrent
snIpAsPathAccessListStringRowStatus
OBJECT-TYPE
This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid
1.3.6.1.4.1.1991.1.2.2.16.1.5INTEGER {invalid(1), valid(2), delete(3), create(4), modify(5)}read-writecurrent
snIpCommunityListStringTable
OBJECT-TYPE
Ip Community ListString table, string version.
1.3.6.1.4.1.1991.1.2.2.17not-accessiblecurrent
snIpCommunityListStringEntry
OBJECT-TYPE
An entry in the Ip Community ListString table.
1.3.6.1.4.1.1991.1.2.2.17.1not-accessiblecurrent
snIpCommunityListStringName
OBJECT-TYPE
The table index for a filter entry.
1.3.6.1.4.1.1991.1.2.2.17.1.1DisplayString (SIZE(0..32))read-onlycurrent
snIpCommunityListStringSequence
OBJECT-TYPE
The table sequence index for a filter entry.
1.3.6.1.4.1.1991.1.2.2.17.1.2Integer32read-onlycurrent
snIpCommunityListStringAction
OBJECT-TYPE
Action to take if the bgp address match with this filter.
1.3.6.1.4.1.1991.1.2.2.17.1.3INTEGER {deny(0), permit(1)}read-writecurrent
snIpCommunityListStringCommNum
OBJECT-TYPE
A number from 1 to 0xFFFFFFFF. There are 20 of them. This integer number is represented by 4 OCTETs. This object is valid for standard community list. For extended type, this will return NULL string. The regular expression string for extended type is available at object snIpCommunityListStringRegExpr
1.3.6.1.4.1.1991.1.2.2.17.1.4OCTET STRING (SIZE(0..80))read-writecurrent
snIpCommunityListStringInternet
OBJECT-TYPE
Disabled/Enabled the Internet Community. Valid only for standard community list. For extended type, 0 is returned.
1.3.6.1.4.1.1991.1.2.2.17.1.5INTEGER {disabled(0), enabled(1)}read-writecurrent
snIpCommunityListStringNoAdvertise
OBJECT-TYPE
Do not advertise this route to any peer (internal or external). Valid only for standard community list. For extended type, 0 is returned.
1.3.6.1.4.1.1991.1.2.2.17.1.6INTEGER {false(0), true(1)}read-writecurrent
snIpCommunityListStringNoExport
OBJECT-TYPE
Do not advertise this route to an EBGP peer. Valid only for standard community list. For extended type, 0 is returned.
1.3.6.1.4.1.1991.1.2.2.17.1.7INTEGER {false(0), true(1)}read-writecurrent
snIpCommunityListStringRowStatus
OBJECT-TYPE
This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid
1.3.6.1.4.1.1991.1.2.2.17.1.8INTEGER {invalid(1), valid(2), delete(3), create(4), modify(5)}read-writecurrent
snIpCommunityListStringLocalAs
OBJECT-TYPE
Send this route to peers in other sub-autonomous systems within the local confederation. Do not advertise this route to an external system. Valid only for standard community list. For extended type, 0 is returned.
1.3.6.1.4.1.1991.1.2.2.17.1.9INTEGER {false(0), true(1)}read-writecurrent
snIpCommunityListStringType
OBJECT-TYPE
Type of the community list, whether standard or extended. Default value is standard.
1.3.6.1.4.1.1991.1.2.2.17.1.10INTEGER {standard(0), extended(1)}read-writecurrent
snIpCommunityListStringRegExpr
OBJECT-TYPE
The regular expression string for extended community list. This object will return NULL for standard community list.
1.3.6.1.4.1.1991.1.2.2.17.1.11DisplayString (SIZE(0..255))read-writecurrent
snRtIpPortIfAddrTable
OBJECT-TYPE
IP port If address table.
1.3.6.1.4.1.1991.1.2.2.18not-accessiblecurrent
snRtIpPortIfAddrEntry
OBJECT-TYPE
An entry in the IP Port Address table.
1.3.6.1.4.1.1991.1.2.2.18.1not-accessiblecurrent
snRtIpPortIfAddrInterfaceIndex
OBJECT-TYPE
The InterfaceIndex for port address entry.
1.3.6.1.4.1.1991.1.2.2.18.1.1InterfaceIndexread-onlycurrent
snRtIpPortIfAddress
OBJECT-TYPE
The port IP address.
1.3.6.1.4.1.1991.1.2.2.18.1.2IpAddressread-onlycurrent
snRtIpPortIfSubnetMask
OBJECT-TYPE
The port IP address subnet mask.
1.3.6.1.4.1.1991.1.2.2.18.1.3IpAddressread-writecurrent
snRtIpPortIfAddrType
OBJECT-TYPE
The port IP address type.
1.3.6.1.4.1.1991.1.2.2.18.1.4INTEGER {primary(1), secondary(2)}read-writecurrent
snRtIpPortIfRowStatus
OBJECT-TYPE
To create or delete a port address entry.
1.3.6.1.4.1.1991.1.2.2.18.1.5RowStsread-writecurrent
snRtIpPortIfAccessTable
OBJECT-TYPE
IP port If access table.
1.3.6.1.4.1.1991.1.2.2.19not-accessiblecurrent
snRtIpPortIfAccessEntry
OBJECT-TYPE
An entry in the IP Port access table.
1.3.6.1.4.1.1991.1.2.2.19.1not-accessiblecurrent
snRtIpPortIfAccessInterfaceIndex
OBJECT-TYPE
The InterfaceIndex for port access entry.
1.3.6.1.4.1.1991.1.2.2.19.1.1InterfaceIndexread-onlycurrent
snRtIpPortIfAccessDirection
OBJECT-TYPE
The incoming or outgoing check for port access.
1.3.6.1.4.1.1991.1.2.2.19.1.2INTEGER {in(1), out(2)}read-onlycurrent
snRtIpPortIfAccessFilters
OBJECT-TYPE
1st octet correspond to 1st filter number and so on.
1.3.6.1.4.1.1991.1.2.2.19.1.3OCTET STRINGread-writecurrent
snRtIpPortIfAccessRowStatus
OBJECT-TYPE
To create or delete a port access entry.
1.3.6.1.4.1.1991.1.2.2.19.1.4RowStsread-writecurrent
snRtIpPortIfConfigTable
OBJECT-TYPE
IP port If Config table.
1.3.6.1.4.1.1991.1.2.2.20not-accessiblecurrent
snRtIpPortIfConfigEntry
OBJECT-TYPE
An entry in the IP Port Config table.
1.3.6.1.4.1.1991.1.2.2.20.1not-accessiblecurrent
snRtIpPortIfConfigInterfaceIndex
OBJECT-TYPE
The If index for port config entry.
1.3.6.1.4.1.1991.1.2.2.20.1.1InterfaceIndexread-onlycurrent
snRtIpPortIfMtu
OBJECT-TYPE
The maximun transfer unit. Ethernet MTU Range: 46 to 1500 POS MTU Range: 60 to 4470 ATM MTU Range: 1500 to 9180 ATM SubIf MTU Range: 1500 to 9180 For jumbo support, MTU range could be higher.
1.3.6.1.4.1.1991.1.2.2.20.1.2Integer32read-writecurrent
snRtIpPortIfEncap
OBJECT-TYPE
Data link encapsulation to be used on the IP frame transmitted on the port.
1.3.6.1.4.1.1991.1.2.2.20.1.3INTEGER {ethernet(1), snap(2), hdlc(3), ppp(4), other(5)}read-writecurrent
snRtIpPortIfMetric
OBJECT-TYPE
The metric.
1.3.6.1.4.1.1991.1.2.2.20.1.4INTEGER (1..15)read-writecurrent
snRtIpPortIfDirBcastFwd
OBJECT-TYPE
Enable/Disable directed broadcast forwarding on the port.
1.3.6.1.4.1.1991.1.2.2.20.1.5RtrStatusread-writecurrent
snRtIpPortConfigIfDonorInterface
OBJECT-TYPE
If this interface is configured as an unnumbered interface, it will return the ifIndex of the donor interface. If this is configured as a donor interface, it will return its own ifIndex value. Otherwise, it will return 0.
1.3.6.1.4.1.1991.1.2.2.20.1.6InterfaceIndexOrZeroread-onlycurrent
agIpPortCounterTable
OBJECT-TYPE
IP port counter table to display IP traffic statistics. At present the system supports only IP statistics for Ethernet ports.
1.3.6.1.4.1.1991.1.2.2.21not-accessiblecurrent
agIpPortCounterEntry
OBJECT-TYPE
An entry in the IP port counter table.
1.3.6.1.4.1.1991.1.2.2.21.1not-accessiblecurrent
agIpPortCounterIpVersion
OBJECT-TYPE
The version of IP protocol for which this counter entry is returned. This table supports ipv4(1) and ipv6(2) enumerations.
1.3.6.1.4.1.1991.1.2.2.21.1.1InetAddressTypenot-accessiblecurrent
agIpPortCounterRxPacket
OBJECT-TYPE
Total IP packets received on a given interface.
1.3.6.1.4.1.1991.1.2.2.21.1.2Counter64read-onlycurrent
agIpPortCounterRxOctet
OBJECT-TYPE
Total IP octets received on a given interface.
1.3.6.1.4.1.1991.1.2.2.21.1.3Counter64read-onlycurrent
agIpPortCounterTxPacket
OBJECT-TYPE
Total IP packets transmitted out from a given interface.
1.3.6.1.4.1.1991.1.2.2.21.1.4Counter64read-onlycurrent
agIpPortCounterTxOctet
OBJECT-TYPE
Total IP octets transmitted out from a given interface.
1.3.6.1.4.1.1991.1.2.2.21.1.5Counter64read-onlycurrent
snRtIpRipGeneral
OBJECT-IDENTITY
1.3.6.1.4.1.1991.1.2.3.1
snRtIpRipEnable
OBJECT-TYPE
Enable/disable ip rip routing.
1.3.6.1.4.1.1991.1.2.3.1.1RtrStatusread-writecurrent
snRtIpRipUpdateTime
OBJECT-TYPE
Ip rip update interval in seconds.
1.3.6.1.4.1.1991.1.2.3.1.2INTEGER (1..21845)read-writecurrent
snRtIpRipRedisEnable
OBJECT-TYPE
Enable/disable redistribution to rip.
1.3.6.1.4.1.1991.1.2.3.1.3RtrStatusread-writecurrent
snRtIpRipRedisDefMetric
OBJECT-TYPE
Default metric to be used when redistribute route to rip.
1.3.6.1.4.1.1991.1.2.3.1.4INTEGER (1..15)read-writecurrent
snRtIpRipSetAllPortConfig
OBJECT-TYPE
The value of this object is an index number of a snRtIpRipPortConfigTable row (i.e. snRtIpRipPortConfigPortIndex), which is the selected row to copy all of its read-writable data (i.e. snRtIpRipPortVersion and snRtIpRipPortPoisonReverse) to the rest of the rows in snRtIpRipPortConfigTable. Note: prior setting this object, all the intended data of the given row of the table must be set. Otherwise, the current data of the row will be used to set the entire ip rip port configuration table. The previous setting will be overwritten by the new one.
1.3.6.1.4.1.1991.1.2.3.1.5Integer32read-writecurrent
snRtIpRipGblFiltList
OBJECT-TYPE
An ip rip global filter list, of which each octet contains a filter ID number that forms a group of filters. A valid entry in the snRtIpRipRouteFilterTable with the corresponding filter ID number (i.e. snRtIpRipRouteFilterId) must have been created before a filter list is initialized. NULL string will be returned if there are no entries of this kind.
1.3.6.1.4.1.1991.1.2.3.1.6OCTET STRING (SIZE(0..64))read-writecurrent
snRtIpRipFiltOnAllPort
OBJECT-TYPE
Apply the ip rip global filter list snRtIpRipGblFiltList to all interfaces. This object is used to add all rip filter lists and delete all rip filter lists to/from all interfaces. Prior to sending this command, snRtIpRipGblFiltList must have been set to a proper filter list. The values that can be written are: deleteAllInBound(2)...delete all in-bound filter lists from all ports. deleteAllOutBound(3)..delete all out-bound filter lists from all ports. addAllInBound(4)......add all in-bound filter lists to all ports. addAllOutBound(5).....add all out-bound filter lists to all ports. If set operation failed, then a SET with value of (2) or (3) returns error code 'GenError'. If succeed, entries in the filter list are deleted immediately. The following values can be returned on reads: valid(1)....set operation is done and is valid.
1.3.6.1.4.1.1991.1.2.3.1.7INTEGER {valid(1), deleteAllInBound(2), deleteAllOutBound(3), addAllInBound(4), addAllOutBound(5)}read-writecurrent
snRtIpRipDistance
OBJECT-TYPE
Administration distance.
1.3.6.1.4.1.1991.1.2.3.1.8INTEGER (1..255)read-writecurrent
snRtIpRipEcmpEnable
OBJECT-TYPE
Enable/disable ECMP for ip rip routing.
1.3.6.1.4.1.1991.1.2.3.1.9RtrStatusread-writecurrent
snRtIpRipPortConfigTable
OBJECT-TYPE
IP Rip port Config table.
1.3.6.1.4.1.1991.1.2.3.2not-accessibledeprecated
snRtIpRipPortConfigEntry
OBJECT-TYPE
An entry in the IP Rip Port Config table.
1.3.6.1.4.1.1991.1.2.3.2.1not-accessibledeprecated
snRtIpRipPortConfigPortIndex
OBJECT-TYPE
The port index for ip rip port config entry.
1.3.6.1.4.1.1991.1.2.3.2.1.1PortIndexread-onlydeprecated
snRtIpRipPortVersion
OBJECT-TYPE
The ip rip version on this port.
1.3.6.1.4.1.1991.1.2.3.2.1.2INTEGER {disabled(0), v1Only(1), v2Only(2), v1CompatibleV2(3)}read-writedeprecated
snRtIpRipPortPoisonReverse
OBJECT-TYPE
Enable/disable poison reverse.
1.3.6.1.4.1.1991.1.2.3.2.1.3RtrStatusread-writedeprecated
snRtIpRipPortLearnDefault
OBJECT-TYPE
Apply the RIP router protocol learn-default option to the interface. The values that can be written are: disabled(0)...deleted the learn default option. enabled(1)....enabled the learn default option.
1.3.6.1.4.1.1991.1.2.3.2.1.4INTEGER {disabled(0), enabled(1)}read-writedeprecated
snRtIpRipRedisTable
OBJECT-TYPE
IP Rip Redistribution table.
1.3.6.1.4.1.1991.1.2.3.3not-accessiblecurrent
snRtIpRipRedisEntry
OBJECT-TYPE
An entry in the IP Rip Redistribution table.
1.3.6.1.4.1.1991.1.2.3.3.1not-accessiblecurrent
snRtIpRipRedisIndex
OBJECT-TYPE
The table index for a IP Rip Redistribution entry.
1.3.6.1.4.1.1991.1.2.3.3.1.1INTEGER (1..64)read-onlycurrent
snRtIpRipRedisAction
OBJECT-TYPE
The action to take when match this IP Rip Redistribution entry.
1.3.6.1.4.1.1991.1.2.3.3.1.2Actionread-writecurrent
snRtIpRipRedisProtocol
OBJECT-TYPE
The protocol to be distributed. other(1) cannot be used for SNMP-SET.
1.3.6.1.4.1.1991.1.2.3.3.1.3INTEGER {other(1), all(2), static(3), ospf(4), bgp(5), isis(6), connected(7)}read-writecurrent
snRtIpRipRedisIp
OBJECT-TYPE
The ip address of the ip route to be distributed. 0.0.0.0 - all routes
1.3.6.1.4.1.1991.1.2.3.3.1.4IpAddressread-writecurrent
snRtIpRipRedisMask
OBJECT-TYPE
The ip subnet mask of the ip route to be distributed.
1.3.6.1.4.1.1991.1.2.3.3.1.5IpAddressread-writecurrent
snRtIpRipRedisMatchMetric
OBJECT-TYPE
The metric of the route to be matched to determine the redistribution. 0 - any metric value
1.3.6.1.4.1.1991.1.2.3.3.1.6Metricread-writecurrent
snRtIpRipRedisSetMetric
OBJECT-TYPE
The new metric of the route to be advertised. 0 - use the default metric.
1.3.6.1.4.1.1991.1.2.3.3.1.7INTEGER (0..15)read-writecurrent
snRtIpRipRedisRowStatus
OBJECT-TYPE
To create or delete a Redistribution entry.
1.3.6.1.4.1.1991.1.2.3.3.1.8RowStsread-writecurrent
snRtIpRipRedisRouteMapName
OBJECT-TYPE
The route map reference for this Redistribution entry.
1.3.6.1.4.1.1991.1.2.3.3.1.9DisplayString (SIZE(0..32))read-writecurrent
snRtIpRipRouteFilterTable
OBJECT-TYPE
ip rip route filter table.
1.3.6.1.4.1.1991.1.2.3.4not-accessiblecurrent
snRtIpRipRouteFilterEntry
OBJECT-TYPE
An entry of the ip rip route filter table.
1.3.6.1.4.1.1991.1.2.3.4.1not-accessiblecurrent
snRtIpRipRouteFilterId
OBJECT-TYPE
The filter ID to identify a filter entry.
1.3.6.1.4.1.1991.1.2.3.4.1.1INTEGER (1..64)read-onlycurrent
snRtIpRipRouteFilterAction
OBJECT-TYPE
Action to take if the ip rip packet matched with this filter.
1.3.6.1.4.1.1991.1.2.3.4.1.2Actionread-writecurrent
snRtIpRipRouteFilterIpAddr
OBJECT-TYPE
Route IP address to compare with any route IP addresses in a ip rip packet. IP address 0.0.0.0 always compare equals to any route IP addresses in any ip rip packets.
1.3.6.1.4.1.1991.1.2.3.4.1.3IpAddressread-writecurrent
snRtIpRipRouteFilterSubnetMask
OBJECT-TYPE
Subnet mask to apply to the route IP address in a ip rip packet, the result is compared to snRtIpRipRouteFilterIpAddr. If snRtIpRipRouteFilterIpAddr is 0.0.0.0, this subnet mask value is ignored.
1.3.6.1.4.1.1991.1.2.3.4.1.4IpAddressread-writecurrent
snRtIpRipRouteFilterRowStatus
OBJECT-TYPE
This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative. valid(2).....the row exists and is valid
1.3.6.1.4.1.1991.1.2.3.4.1.5INTEGER {invalid(1), valid(2), delete(3), create(4), modify(5)}read-writecurrent
snRtIpRipNbrFilterTable
OBJECT-TYPE
ip rip neighbor filter table.
1.3.6.1.4.1.1991.1.2.3.5not-accessiblecurrent
snRtIpRipNbrFilterEntry
OBJECT-TYPE
An entry of the ip rip neighbor filter table.
1.3.6.1.4.1.1991.1.2.3.5.1not-accessiblecurrent
snRtIpRipNbrFilterId
OBJECT-TYPE
The filter ID to identify a filter entry.
1.3.6.1.4.1.1991.1.2.3.5.1.1INTEGER (1..64)read-onlycurrent
snRtIpRipNbrFilterAction
OBJECT-TYPE
Action to take if the ip rip packet source IP address compares equal to the source IP address in this filter.
1.3.6.1.4.1.1991.1.2.3.5.1.2Actionread-writecurrent
snRtIpRipNbrFilterSourceIp
OBJECT-TYPE
Source IP address to compare with the source IP address in a ip rip packet. IP address 0.0.0.0 always compares equal to any source IP addresses in any ip rip packets.
1.3.6.1.4.1.1991.1.2.3.5.1.3IpAddressread-writecurrent
snRtIpRipNbrFilterRowStatus
OBJECT-TYPE
This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative. valid(2).....the row exists and is valid
1.3.6.1.4.1.1991.1.2.3.5.1.4INTEGER {invalid(1), valid(2), delete(3), create(4), modify(5)}read-writecurrent
snRtIpRipPortAccessTable
OBJECT-TYPE
ip interface rip access table.
1.3.6.1.4.1.1991.1.2.3.6not-accessibledeprecated
snRtIpRipPortAccessEntry
OBJECT-TYPE
An entry of the ip interface rip access table.
1.3.6.1.4.1.1991.1.2.3.6.1not-accessibledeprecated
snRtIpRipPortAccessPort
OBJECT-TYPE
The ip interface to which the rip filter applies.
1.3.6.1.4.1.1991.1.2.3.6.1.1PortIndexread-onlydeprecated
snRtIpRipPortAccessDir
OBJECT-TYPE
The access direction of incoming packet filter or outgoing packet filter.
1.3.6.1.4.1.1991.1.2.3.6.1.2INTEGER {in(1), out(2)}read-onlydeprecated
snRtIpRipPortAccessFilterList
OBJECT-TYPE
An ip rip filter list, of which each octet contains a filter ID number that forms a group of filters. A valid entry in the snRtIpRipRouteFilterTable with the corresponding filter ID number (i.e. snRtIpRipRouteFilterId) must have been created before a filter list is initialized.
1.3.6.1.4.1.1991.1.2.3.6.1.3OCTET STRING (SIZE(1..64))read-writedeprecated
snRtIpRipPortAccessRowStatus
OBJECT-TYPE
This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative. valid(2).....the row exists and is valid
1.3.6.1.4.1.1991.1.2.3.6.1.4INTEGER {invalid(1), valid(2), delete(3), create(4), modify(5)}read-writedeprecated
snRtIpRipPortIfConfigTable
OBJECT-TYPE
IP Rip port If Config table.
1.3.6.1.4.1.1991.1.2.3.7not-accessiblecurrent
snRtIpRipPortIfConfigEntry
OBJECT-TYPE
An entry in the IP Rip Port If Config table.
1.3.6.1.4.1.1991.1.2.3.7.1not-accessiblecurrent
snRtIpRipPortIfConfigInterfaceIndex
OBJECT-TYPE
The If index for ip rip port config entry.
1.3.6.1.4.1.1991.1.2.3.7.1.1InterfaceIndexread-onlycurrent
snRtIpRipPortIfVersion
OBJECT-TYPE
The ip rip version on this port.
1.3.6.1.4.1.1991.1.2.3.7.1.2INTEGER {disabled(0), v1Only(1), v2Only(2), v1CompatibleV2(3)}read-writecurrent
snRtIpRipPortIfPoisonReverse
OBJECT-TYPE
Enable/disable poison reverse.
1.3.6.1.4.1.1991.1.2.3.7.1.3RtrStatusread-writecurrent
snRtIpRipPortIfLearnDefault
OBJECT-TYPE
Apply the RIP router protocol learn-default option to the interface. The values that can be written are: disabled(0)...deleted the learn default option. enabled(1)....enabled the learn default option.
1.3.6.1.4.1.1991.1.2.3.7.1.4INTEGER {disabled(0), enabled(1)}read-writecurrent
snRtIpRipPortIfAccessTable
OBJECT-TYPE
ip interface rip access table.
1.3.6.1.4.1.1991.1.2.3.8not-accessiblecurrent
snRtIpRipPortIfAccessEntry
OBJECT-TYPE
An entry of the ip interface rip access table.
1.3.6.1.4.1.1991.1.2.3.8.1not-accessiblecurrent
snRtIpRipPortIfAccessPort
OBJECT-TYPE
The ip interface to which the rip filter applies.
1.3.6.1.4.1.1991.1.2.3.8.1.1InterfaceIndexread-onlycurrent
snRtIpRipPortIfAccessDir
OBJECT-TYPE
The access direction of incoming packet filter or outgoing packet filter.
1.3.6.1.4.1.1991.1.2.3.8.1.2INTEGER {in(1), out(2)}read-onlycurrent
snRtIpRipPortIfAccessFilterList
OBJECT-TYPE
An ip rip filter list, of which each octet contains a filter ID number that forms a group of filters. A valid entry in the snRtIpRipRouteFilterTable with the corresponding filter ID number (i.e. snRtIpRipRouteFilterId) must have been created before a filter list is initialized.
1.3.6.1.4.1.1991.1.2.3.8.1.3OCTET STRING (SIZE(1..64))read-writecurrent
snRtIpRipPortIfAccessRowStatus
OBJECT-TYPE
This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative. valid(2).....the row exists and is valid
1.3.6.1.4.1.1991.1.2.3.8.1.4INTEGER {invalid(1), valid(2), delete(3), create(4), modify(5)}read-writecurrent
snRtIpRipStats
OBJECT-IDENTITY
1.3.6.1.4.1.1991.1.2.3.9
snRtIpRipStatsOutRequest
OBJECT-TYPE
Number of outgoing RIP requests.
1.3.6.1.4.1.1991.1.2.3.9.1Counter32read-onlycurrent
snRtIpRipStatsOutResponse
OBJECT-TYPE
Number of outgoing RIP responses.
1.3.6.1.4.1.1991.1.2.3.9.2Counter32read-onlycurrent
snRtIpRipStatsInRequest
OBJECT-TYPE
Number of incoming RIP requests.
1.3.6.1.4.1.1991.1.2.3.9.3Counter32read-onlycurrent
snRtIpRipStatsInResponse
OBJECT-TYPE
Number of incoming RIP responses.
1.3.6.1.4.1.1991.1.2.3.9.4Counter32read-onlycurrent
snRtIpRipStatsUnrecognized
OBJECT-TYPE
Number of unrecognized RIP packets.
1.3.6.1.4.1.1991.1.2.3.9.5Counter32read-onlycurrent
snRtIpRipStatsBadVersion
OBJECT-TYPE
Number of RIP packets with bad version number.
1.3.6.1.4.1.1991.1.2.3.9.6Counter32read-onlycurrent
snRtIpRipStatsBadAddrFamily
OBJECT-TYPE
Number of RIP packets with bad address family value.
1.3.6.1.4.1.1991.1.2.3.9.7Counter32read-onlycurrent
snRtIpRipStatsBadRequestFormat
OBJECT-TYPE
Number of RIP packets with bad request format.
1.3.6.1.4.1.1991.1.2.3.9.8Counter32read-onlycurrent
snRtIpRipStatsBadMetrics
OBJECT-TYPE
Number of RIP packets with bad metric value.
1.3.6.1.4.1.1991.1.2.3.9.9Counter32read-onlycurrent
snRtIpRipStatsBadRespFormat
OBJECT-TYPE
Number of RIP packets with bad response format.
1.3.6.1.4.1.1991.1.2.3.9.10Counter32read-onlycurrent
snRtIpRipStatsRespFromNonRipPort
OBJECT-TYPE
Number of RIP packet responses coming from non-RIP configured ports.
1.3.6.1.4.1.1991.1.2.3.9.11Counter32read-onlycurrent
snRtIpRipStatsResponseFromLoopback
OBJECT-TYPE
Number of RIP packet responses coming from loopback ports.
1.3.6.1.4.1.1991.1.2.3.9.12Counter32read-onlycurrent
snRtIpRipStatsPacketRejected
OBJECT-TYPE
Number of RIP packets rejected.
1.3.6.1.4.1.1991.1.2.3.9.13Counter32read-onlycurrent
snDvmrpMIBObjects
OBJECT-IDENTITY
1.3.6.1.4.1.1991.1.2.5.1
snDvmrpVersion
OBJECT-TYPE
The router's DVMRP version information.
1.3.6.1.4.1.1991.1.2.5.1.1DisplayString (SIZE(0..255))read-onlycurrent
snDvmrpEnable
OBJECT-TYPE
Enable or disable DVMRP on this router.
1.3.6.1.4.1.1991.1.2.5.1.2RtrStatusread-writecurrent
snDvmrpGenerationId
OBJECT-TYPE
The generation identifier for the routing process. This is used by neighboring routers to detect whether pruning information should be resent.
1.3.6.1.4.1.1991.1.2.5.1.3Integer32read-onlycurrent
snDvmrpProbeInterval
OBJECT-TYPE
This is the time interval at which the router sends out probe messages to discover neighbour routers. Value is in number of seconds. snDvmrpEnable must be 'enabled' before this object is writen.
1.3.6.1.4.1.1991.1.2.5.1.4INTEGER (5..30)read-writecurrent
snDvmrpReportInterval
OBJECT-TYPE
This is the time interval at which the router sends out full report messages. Value is in number of seconds. snDvmrpEnable must be 'enabled' before this object is writen.
1.3.6.1.4.1.1991.1.2.5.1.5INTEGER (10..2000)read-writecurrent
snDvmrpTriggerInterval
OBJECT-TYPE
This is the time interval at which triggered updates are sent out. Value is in number of seconds. snDvmrpEnable must be 'enabled' before this object is writen.
1.3.6.1.4.1.1991.1.2.5.1.6INTEGER (5..30)read-writecurrent
snDvmrpNeighborRouterTimeout
OBJECT-TYPE
This is the time interval after which the neighbour router is considered down. Value is in number of seconds. snDvmrpEnable must be 'enabled' before this object is writen.
1.3.6.1.4.1.1991.1.2.5.1.7INTEGER (60..8000)read-writecurrent
snDvmrpRouteExpireTime
OBJECT-TYPE
This is the time interval after which the route expires and becomes unreachable. Value is in number of seconds. snDvmrpEnable must be 'enabled' before this object is writen.
1.3.6.1.4.1.1991.1.2.5.1.8INTEGER (20..4000)read-writecurrent
snDvmrpRouteDiscardTime
OBJECT-TYPE
This is the time interval after which a route is discarded from the route table. Value is in number of seconds. snDvmrpEnable must be 'enabled' before this object is writen.
1.3.6.1.4.1.1991.1.2.5.1.9INTEGER (40..8000)read-writecurrent
snDvmrpPruneAge
OBJECT-TYPE
This is the duration of time for which the prune state is stored. Value is in number of seconds. snDvmrpEnable must be 'enabled' before this object is writen.
1.3.6.1.4.1.1991.1.2.5.1.10INTEGER (20..3600)read-writecurrent
snDvmrpGraftRetransmitTime
OBJECT-TYPE
This is the time interval after which a graft message will be retransmitted if graft acknowledge message has not been received. Value is in number of seconds. snDvmrpEnable must be 'enabled' before this object is writen. For FastIron platforms, the default value is 3 and the range is between 2 to 10. For NetIron platforms, the range is between 5 to 3600.
1.3.6.1.4.1.1991.1.2.5.1.11INTEGER (2..3600)read-writecurrent
snDvmrpDefaultRoute
OBJECT-TYPE
This is the IP address of a router that is connected to one of the directly attached subnet. If a multicast route is not present on the local router, this default route will be used for multicast forwarding. snDvmrpEnable must be 'enabled' before this object is writen.
1.3.6.1.4.1.1991.1.2.5.1.12IpAddressread-writecurrent
snDvmrpVInterfaceTable
OBJECT-TYPE
The (conceptual) table listing the router's DVMRP virtual interfaces. snDvmrpEnable must be 'enabled' before this table is read or writen.
1.3.6.1.4.1.1991.1.2.5.1.13not-accessiblecurrent
snDvmrpVInterfaceEntry
OBJECT-TYPE
An entry (conceptual row) in the snDvmrpVInterfaceTable. This row augments ipMRouteInterfaceEntry in the IP Multicast MIB, where the threshold object resides.
1.3.6.1.4.1.1991.1.2.5.1.13.1not-accessiblecurrent
snDvmrpVInterfaceVifIndex
OBJECT-TYPE
The ifIndex value of this DVMRP virtual interface.
1.3.6.1.4.1.1991.1.2.5.1.13.1.1INTEGER (1..48)read-onlycurrent
snDvmrpVInterfaceType
OBJECT-TYPE
The type of this DVMRP virtual interface, whether it uses a tunnel, a physical interface for which we are a querier, or a physical interface for which we are not a querier. For write operation, this object can only accept tunnel(1) to configure a tunnel interface or subnet(3) to configure a physical interface.
1.3.6.1.4.1.1991.1.2.5.1.13.1.2INTEGER {tunnel(1), querier(2), subnet(3)}read-writecurrent
snDvmrpVInterfaceOperState
OBJECT-TYPE
The current operational state of this DVMRP virtual interface.
1.3.6.1.4.1.1991.1.2.5.1.13.1.3INTEGER {up(1), down(2)}read-onlycurrent
snDvmrpVInterfaceLocalAddress
OBJECT-TYPE
The IP address of the local end of this DVMRP virtual interface.
1.3.6.1.4.1.1991.1.2.5.1.13.1.4IpAddressread-writecurrent
snDvmrpVInterfaceRemoteAddress
OBJECT-TYPE
The IP address of the remote end of this DVMRP virtual interface. For a tunnel, this is the IP address of the neighboring router. For a subnet, this is the subnet address.
1.3.6.1.4.1.1991.1.2.5.1.13.1.5IpAddressread-writecurrent
snDvmrpVInterfaceRemoteSubnetMask
OBJECT-TYPE
The subnet mask for a directly connected subnet. For a tunnel, this should be 0.0.0.0.
1.3.6.1.4.1.1991.1.2.5.1.13.1.6IpAddressread-onlycurrent
snDvmrpVInterfaceMetric
OBJECT-TYPE
The distance metric for this DVMRP virtual interface which is used to calculate distance vectors.
1.3.6.1.4.1.1991.1.2.5.1.13.1.7INTEGER (1..31)read-writecurrent
snDvmrpVInterfaceTtlThreshold
OBJECT-TYPE
This is the minimum time-to-live value to forward the packets out of this virtual interface.
1.3.6.1.4.1.1991.1.2.5.1.13.1.8INTEGER (1..254)read-writecurrent
snDvmrpVInterfaceAdvertiseLocal
OBJECT-TYPE
Enable or disable the advertising of this local route.
1.3.6.1.4.1.1991.1.2.5.1.13.1.9RtrStatusread-writecurrent
snDvmrpVInterfaceEncapsulation
OBJECT-TYPE
Enable or disable the encapsulation of the DVMRP control packets when using IPINIP encapsulation.
1.3.6.1.4.1.1991.1.2.5.1.13.1.10RtrStatusread-writecurrent
snDvmrpVInterfaceStatus
OBJECT-TYPE
This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative. valid(2)....Setting it to 'valid' has the effect of changing the row to operative.
1.3.6.1.4.1.1991.1.2.5.1.13.1.11INTEGER {invalid(1), valid(2), delete(3), create(4), modify(5)}read-writecurrent
snDvmrpNeighborTable
OBJECT-TYPE
The (conceptual) table listing the router's DVMRP neighbors, as discovered by receiving Neighbor Probe messages. snDvmrpEnable must be 'enabled' before this table is read.
1.3.6.1.4.1.1991.1.2.5.1.14not-accessiblecurrent
snDvmrpNeighborEntry
OBJECT-TYPE
An entry (conceptual row) in the snDvmrpNeighborTable.
1.3.6.1.4.1.1991.1.2.5.1.14.1not-accessiblecurrent
snDvmrpNeighborEntryIndex
OBJECT-TYPE
The table entry index.
1.3.6.1.4.1.1991.1.2.5.1.14.1.1Integer32read-onlycurrent
snDvmrpNeighborVifIndex
OBJECT-TYPE
The value of VifIndex for the virtual interface used to reach this DVMRP neighbor.
1.3.6.1.4.1.1991.1.2.5.1.14.1.2Integer32read-onlycurrent
snDvmrpNeighborAddress
OBJECT-TYPE
The IP address of the DVMRP neighbor for which this entry contains information.
1.3.6.1.4.1.1991.1.2.5.1.14.1.3IpAddressread-onlycurrent
snDvmrpNeighborUpTime
OBJECT-TYPE
The time since this DVMRP neighbor (last) became a neighbor of the local router.
1.3.6.1.4.1.1991.1.2.5.1.14.1.4TimeTicksread-onlycurrent
snDvmrpNeighborExpiryTime
OBJECT-TYPE
The minimum time remaining before this DVMRP neighbor will be aged out.
1.3.6.1.4.1.1991.1.2.5.1.14.1.5TimeTicksread-onlycurrent
snDvmrpNeighborGenerationId
OBJECT-TYPE
The neighboring router's generation identifier.
1.3.6.1.4.1.1991.1.2.5.1.14.1.6Integer32read-onlycurrent
snDvmrpNeighborMajorVersion
OBJECT-TYPE
The neighboring router's major DVMRP version number.
1.3.6.1.4.1.1991.1.2.5.1.14.1.7INTEGER (0..255)read-onlycurrent
snDvmrpNeighborMinorVersion
OBJECT-TYPE
The neighboring router's minor DVMRP version number.
1.3.6.1.4.1.1991.1.2.5.1.14.1.8INTEGER (0..255)read-onlycurrent
snDvmrpNeighborCapabilities
OBJECT-TYPE
This object describes the neighboring router's capabilities. The following shows the position of each bit: bit position meaning ----------- ------ 3 mtrace bit 2 generationID bit 1 prune bit 0 leaf bit The leaf bit indicates that the neighbor has only one interface with neighbors. The prune bit indicates that the neighbor supports pruning. The generationID bit indicates that the neighbor sends its generationID in Probe messages. The mtrace bit indicates that the neighbor can handle mtrace requests.
1.3.6.1.4.1.1991.1.2.5.1.14.1.9Integer32read-onlycurrent
snDvmrpRouteTable
OBJECT-TYPE
The routing table used by DVMRP in place of the unicast routing table. snDvmrpEnable must be 'enabled' before this table is read.
1.3.6.1.4.1.1991.1.2.5.1.15not-accessiblecurrent
snDvmrpRouteEntry
OBJECT-TYPE
An entry (conceptual row) containing the multicast routing information used by DVMRP in place of the unicast routing information.
1.3.6.1.4.1.1991.1.2.5.1.15.1not-accessiblecurrent
snDvmrpRouteEntryIndex
OBJECT-TYPE
The table entry index.
1.3.6.1.4.1.1991.1.2.5.1.15.1.1Integer32read-onlycurrent
snDvmrpRouteSource
OBJECT-TYPE
The network address which when combined with the corresponding value of snDvmrpRouteSourceMask identifies the sources for which this entry contains multicast routing information.
1.3.6.1.4.1.1991.1.2.5.1.15.1.2IpAddressread-onlycurrent
snDvmrpRouteSourceMask
OBJECT-TYPE
The network mask which when combined with the corresponding value of snDvmrpRouteSource identifies the sources for which this entry contains multicast routing information.
1.3.6.1.4.1.1991.1.2.5.1.15.1.3IpAddressread-onlycurrent
snDvmrpRouteUpstreamNeighbor
OBJECT-TYPE
The address of the upstream neighbor (e.g., RPF neighbor) from which IP datagrams from these sources are received.
1.3.6.1.4.1.1991.1.2.5.1.15.1.4IpAddressread-onlycurrent
snDvmrpRouteVifIndex
OBJECT-TYPE
The value of snDvmrpVInterfaceVifIndex for the virtual interface on which IP datagrams sent by these sources are received.
1.3.6.1.4.1.1991.1.2.5.1.15.1.5Integer32read-onlycurrent
snDvmrpRouteMetric
OBJECT-TYPE
The distance in hops to the source subnet.
1.3.6.1.4.1.1991.1.2.5.1.15.1.6Integer32read-onlycurrent
snDvmrpRouteExpiryTime
OBJECT-TYPE
The minimum amount of time remaining before this entry will be aged out.
1.3.6.1.4.1.1991.1.2.5.1.15.1.7TimeTicksread-onlycurrent
snDvmrpRouteNextHopTable
OBJECT-TYPE
The (conceptual) table containing information on the next hops on outgoing interfaces for routing IP multicast datagrams. snDvmrpEnable must be 'enabled' before this table is read.
1.3.6.1.4.1.1991.1.2.5.1.16not-accessiblecurrent
snDvmrpRouteNextHopEntry
OBJECT-TYPE
An entry (conceptual row) in the list of next hops on outgoing interfaces to which IP multicast datagrams from particular sources are routed.
1.3.6.1.4.1.1991.1.2.5.1.16.1not-accessiblecurrent
snDvmrpRouteNextHopSource
OBJECT-TYPE
The network address which when combined with the corresponding value of snDvmrpRouteNextHopSourceMask identifies the sources for which this entry specifies a next hop on an outgoing interface.
1.3.6.1.4.1.1991.1.2.5.1.16.1.1IpAddressread-onlycurrent
snDvmrpRouteNextHopSourceMask
OBJECT-TYPE
The network mask which when combined with the corresponding value of snDvmrpRouteNextHopSource identifies the sources for which this entry specifies a next hop on an outgoing interface.
1.3.6.1.4.1.1991.1.2.5.1.16.1.2IpAddressread-onlycurrent
snDvmrpRouteNextHopVifIndex
OBJECT-TYPE
The snDvmrpVInterfaceVifIndex value of the virtual interface for the outgoing interface for this next hop.
1.3.6.1.4.1.1991.1.2.5.1.16.1.3Integer32read-onlycurrent
snDvmrpRouteNextHopType
OBJECT-TYPE
Type is leaf if no neighbors exist on the outgoing virtual interface. Otherwise, type is branch.
1.3.6.1.4.1.1991.1.2.5.1.16.1.4INTEGER {leaf(1), branch(2)}read-onlycurrent
snDvmrpVIfStatTable
OBJECT-TYPE
The (conceptual) table listing the router's DVMRP virtual interface statistical counters. snDvmrpEnable must be 'enabled' before this table is read.
1.3.6.1.4.1.1991.1.2.5.1.17not-accessiblecurrent
snDvmrpVIfStatEntry
OBJECT-TYPE
An entry (conceptual row) in the snDvmrpVIfStatTable.
1.3.6.1.4.1.1991.1.2.5.1.17.1not-accessiblecurrent
snDvmrpVIfStatVifIndex
OBJECT-TYPE
The ifIndex value of this DVMRP virtual interface.
1.3.6.1.4.1.1991.1.2.5.1.17.1.1INTEGER (1..65535)read-onlycurrent
snDvmrpVIfStatInPkts
OBJECT-TYPE
The number of packets that have arrived on the DVMRP virtual interface.
1.3.6.1.4.1.1991.1.2.5.1.17.1.2Counter32read-onlycurrent
snDvmrpVIfStatOutPkts
OBJECT-TYPE
The number of packets that have been sent on the DVMRP virtual interface.
1.3.6.1.4.1.1991.1.2.5.1.17.1.3Counter32read-onlycurrent
snDvmrpVIfStatInOctets
OBJECT-TYPE
The number of octets that have arrived on the DVMRP virtual interface.
1.3.6.1.4.1.1991.1.2.5.1.17.1.4Counter32read-onlycurrent
snDvmrpVIfStatOutOctets
OBJECT-TYPE
The number of octets that have been sent on the DVMRP virtual interface.
1.3.6.1.4.1.1991.1.2.5.1.17.1.5Counter32read-onlycurrent
snDvmrpVIfStatInProbePkts
OBJECT-TYPE
The number of probe packets that have arrived on the DVMRP virtual interface.
1.3.6.1.4.1.1991.1.2.5.1.17.1.6Counter32read-onlycurrent
snDvmrpVIfStatOutProbePkts
OBJECT-TYPE
The number of probe packets that have been sent on the DVMRP virtual interface.
1.3.6.1.4.1.1991.1.2.5.1.17.1.7Counter32read-onlycurrent
snDvmrpVIfStatDiscardProbePkts
OBJECT-TYPE
The number of probe packets that have been discarded by the DVMRP virtual interface.
1.3.6.1.4.1.1991.1.2.5.1.17.1.8Counter32read-onlycurrent
snDvmrpVIfStatInRtUpdatePkts
OBJECT-TYPE
The number of route update packets that have arrived on the DVMRP virtual interface.
1.3.6.1.4.1.1991.1.2.5.1.17.1.9Counter32read-onlycurrent
snDvmrpVIfStatOutRtUpdatePkts
OBJECT-TYPE
The number of route update packets that have been sent on the DVMRP virtual interface.
1.3.6.1.4.1.1991.1.2.5.1.17.1.10Counter32read-onlycurrent
snDvmrpVIfStatDiscardRtUpdatePkts
OBJECT-TYPE
The number of route update packets that have been discarded by the DVMRP virtual interface.
1.3.6.1.4.1.1991.1.2.5.1.17.1.11Counter32read-onlycurrent
snDvmrpVIfStatInGraftPkts
OBJECT-TYPE
The number of graft packets that have arrived on the DVMRP virtual interface.
1.3.6.1.4.1.1991.1.2.5.1.17.1.12Counter32read-onlycurrent
snDvmrpVIfStatOutGraftPkts
OBJECT-TYPE
The number of graft packets that have been sent on the DVMRP virtual interface.
1.3.6.1.4.1.1991.1.2.5.1.17.1.13Counter32read-onlycurrent
snDvmrpVIfStatDiscardGraftPkts
OBJECT-TYPE
The number of graft packets that have been discarded by the DVMRP virtual interface.
1.3.6.1.4.1.1991.1.2.5.1.17.1.14Counter32read-onlycurrent
snDvmrpVIfStatInGraftAckPkts
OBJECT-TYPE
The number of graft acknowledge packets that have arrived on the DVMRP virtual interface.
1.3.6.1.4.1.1991.1.2.5.1.17.1.15Counter32read-onlycurrent
snDvmrpVIfStatOutGraftAckPkts
OBJECT-TYPE
The number of graft acknowledge packets that have been sent on the DVMRP virtual interface.
1.3.6.1.4.1.1991.1.2.5.1.17.1.16Counter32read-onlycurrent
snDvmrpVIfStatDiscardGraftAckPkts
OBJECT-TYPE
The number of graft acknowledge packets that have been discarded by the DVMRP virtual interface.
1.3.6.1.4.1.1991.1.2.5.1.17.1.17Counter32read-onlycurrent
snDvmrpVIfStatInPrunePkts
OBJECT-TYPE
The number of prune packets that have arrived on the DVMRP virtual interface.
1.3.6.1.4.1.1991.1.2.5.1.17.1.18Counter32read-onlycurrent
snDvmrpVIfStatOutPrunePkts
OBJECT-TYPE
The number of prune packets that have been sent on the DVMRP virtual interface.
1.3.6.1.4.1.1991.1.2.5.1.17.1.19Counter32read-onlycurrent
snDvmrpVIfStatDiscardPrunePkts
OBJECT-TYPE
The number of prune packets that have been discarded by the DVMRP virtual interface.
1.3.6.1.4.1.1991.1.2.5.1.17.1.20Counter32read-onlycurrent
snFsrpGlobal
OBJECT-IDENTITY
1.3.6.1.4.1.1991.1.2.7.1
snFsrpGroupOperMode
OBJECT-TYPE
The FSRP is configured on this system either enabled or disabled and the default is disabled mode. disabled(0)..........disable FSRP enabled(1)...........activate FSRP
1.3.6.1.4.1.1991.1.2.7.1.1INTEGER {disabled(0), enabled(1)}read-writecurrent
snFsrpIfStateChangeTrap
OBJECT-TYPE
Indicates whether the SNMP agent process is permitted to generate FSRP interface state change traps.
1.3.6.1.4.1.1991.1.2.7.1.2INTEGER {disabled(0), enabled(1)}read-writecurrent
snFsrpIntf
OBJECT-IDENTITY
1.3.6.1.4.1.1991.1.2.7.2
snFsrpIfTable
OBJECT-TYPE
The FSRP Interface Table describes the interfaces from the viewpoint of FSRP.
1.3.6.1.4.1.1991.1.2.7.2.1not-accessiblecurrent
snFsrpIfEntry
OBJECT-TYPE
The FSRP Interface Entry describes one interface from the viewpoint of FSRP.
1.3.6.1.4.1.1991.1.2.7.2.1.1not-accessiblecurrent
snFsrpIfPort
OBJECT-TYPE
The physical router port of this FSRP interface.
1.3.6.1.4.1.1991.1.2.7.2.1.1.1Integer32read-onlycurrent
snFsrpIfIpAddress
OBJECT-TYPE
The IP Address of the physical router port of this interface.
1.3.6.1.4.1.1991.1.2.7.2.1.1.2IpAddressread-onlycurrent
snFsrpIfVirRtrIpAddr
OBJECT-TYPE
The IP Address of the Virtual Router for the interface. The Virtual Router IP address need to be configured on the interface before Redundant Router Function can operate on the interface. This address has to be same on all the routers that going to participate in the Redundant Router Function on a given subnet.
1.3.6.1.4.1.1991.1.2.7.2.1.1.3IpAddressread-writecurrent
snFsrpIfOtherRtrIpAddr
OBJECT-TYPE
The IP Address of the Other Router on this ip subnet that operates FSRP and to whom the Keep Alive message need to be sent by this router. This object must be configured for FSRP to work correctly
1.3.6.1.4.1.1991.1.2.7.2.1.1.4IpAddressread-writecurrent
snFsrpIfPreferLevel
OBJECT-TYPE
The higher the number the higher the priority is. This parameter decides which router should becomes the Active Router for the interface. A Router with higher priority selected to becomes the Active Router.
1.3.6.1.4.1.1991.1.2.7.2.1.1.5INTEGER (1..255)read-writecurrent
snFsrpIfTrackPortMask
OBJECT-TYPE
This object specifies the identity of the physical port whose state is to be monitored. Each bit is a port of the system. Default value is 0. If this object is configured then the Preference Level of this interface will be adjusted dynamically depending on the state of the Track Port. The interface's Preference Level is reduced by value of Preference Level parameter when the Track Port states first changes from UP to DOWN. When the Track Port next comes up the interface's Preference Level is increased by the amount specified by the Preference Level. The Standalone router FSRP Track port membership (Not used for Chassis Product)
1.3.6.1.4.1.1991.1.2.7.2.1.1.6PortMaskread-writedeprecated
snFsrpIfRowStatus
OBJECT-TYPE
This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid
1.3.6.1.4.1.1991.1.2.7.2.1.1.7INTEGER {invalid(1), valid(2), delete(3), create(4), modify(5)}read-writecurrent
snFsrpIfState
OBJECT-TYPE
This object specifies the FSRP Router's interface state as: init(0)...initialization state. negotiating(1)...negotiating state. standby(2)...standby state. active(3)...active state.
1.3.6.1.4.1.1991.1.2.7.2.1.1.8INTEGER {init(0), negotiating(1), standby(2), active(3)}read-onlycurrent
snFsrpIfKeepAliveTime
OBJECT-TYPE
The heart-beat is from 1 to 120 seconds.
1.3.6.1.4.1.1991.1.2.7.2.1.1.9INTEGER (1..120)read-writecurrent
snFsrpIfRouterDeadTime
OBJECT-TYPE
The hold time of the Fsrp router is from 3 to 255 seconds.
1.3.6.1.4.1.1991.1.2.7.2.1.1.10INTEGER (3..255)read-writecurrent
snFsrpIfChassisTrackPortMask
OBJECT-TYPE
This object specifies the identity of the physical port whose state is to be monitored. Each bit is a port of the system. Default value is 0. If this object is configured then the Preference Level of this interface will be adjusted dynamically depending on the state of the Track Port. The interface's Preference Level is reduced by value of Preference Level parameter when the Track Port states first changes from UP to DOWN. When the Track Port next comes up the interface's Preference Level is increased by the amount specified by the Preference Level. The Chassis router FSRP Track port membership. (It was obsoleted after release 07100, replaced by snFsrpIfTrackPortList)
1.3.6.1.4.1.1991.1.2.7.2.1.1.11OCTET STRING (SIZE(32))read-writedeprecated
snFsrpIfTrackPortList
OBJECT-TYPE
This object specifies the identity of the physical port whose state is to be monitored. Each port index is a 16-bit integer in big endian order. 8-bit is the slot number, the other 8-bit is the port number. Default value is 0 length octet string. If this object is configured then the Preference Level of this interface will be adjusted dynamically depending on the state of the Track Port. The interface's Preference Level is reduced by value of Preference Level parameter when the Track Port states first changes from UP to DOWN. When the Track Port next comes up the interface's Preference Level is increased by the amount specified by the Preference Level. The router FSRP physical track port membership.
1.3.6.1.4.1.1991.1.2.7.2.1.1.12OCTET STRINGread-writecurrent
snGblRtGeneral
OBJECT-IDENTITY
1.3.6.1.4.1.1991.1.2.8.1
snGblRtRouteOnly
OBJECT-TYPE
If this object is 'enabled', this switching router will only route packets. If this object is 'disabled', this switching router will first route packets. If route cannot perform, it will switch packets.
1.3.6.1.4.1.1991.1.2.8.1.1RtrStatusread-writecurrent
snPimMIBObjects
OBJECT-IDENTITY
1.3.6.1.4.1.1991.1.2.9.1
snPimEnable
OBJECT-TYPE
Enable or disable PIM on this router.
1.3.6.1.4.1.1991.1.2.9.1.1RtrStatusread-writecurrent
snPimNeighborRouterTimeout
OBJECT-TYPE
This is the time interval after which the neighbour router is considered down. Value is in number of seconds. snPimEnable must be 'enabled' before this object is writen.
1.3.6.1.4.1.1991.1.2.9.1.2INTEGER (60..8000)read-writecurrent
snPimHelloTime
OBJECT-TYPE
This is the interval at which hello message is sent out an interface to the neighbouring router. This is used to detect the presence or abscense of a neighbouring router. Value is in number of seconds. snPimEnable must be 'enabled' before this object is writen.
1.3.6.1.4.1.1991.1.2.9.1.3INTEGER (10..3600)read-writecurrent
snPimPruneTime
OBJECT-TYPE
This is the duration of time for which the prune state is stored. Value is in number of seconds. snPimEnable must be 'enabled' before this object is writen. For FastIron platforms, the default value is 180.
1.3.6.1.4.1.1991.1.2.9.1.4INTEGER (10..3600)read-writecurrent
snPimGraftRetransmitTime
OBJECT-TYPE
This is the time interval after which a graft message will be retransmitted if graft acknowledge message has not been received. Value is in number of seconds. snPimEnable must be 'enabled' before this object is writen.
1.3.6.1.4.1.1991.1.2.9.1.5INTEGER (10..3600)read-writecurrent
snPimInactivityTime
OBJECT-TYPE
This is the interval after which the forwarding entry is deleted. When a packet is received for a group entry, this time is reset. This is used to only keep the forwarding entries for the active sessions. Value is in number of seconds. snPimEnable must be 'enabled' before this object is writen. For FastIron platforms, the default value is 3 and the range is between 2 to 10. For NetIron platforms, the range is between 10 to 3600.
1.3.6.1.4.1.1991.1.2.9.1.6INTEGER (2..3600)read-writecurrent
snPimVInterfaceTable
OBJECT-TYPE
The (conceptual) table listing the router's PIM virtual interfaces. snPimEnable must be 'enabled' before this table is read or writen.
1.3.6.1.4.1.1991.1.2.9.1.7not-accessiblecurrent
snPimVInterfaceEntry
OBJECT-TYPE
An entry (conceptual row) in the snPimVInterfaceTable.
1.3.6.1.4.1.1991.1.2.9.1.7.1not-accessiblecurrent
snPimVInterfaceVifIndex
OBJECT-TYPE
The ifIndex value of this PIM virtual interface.
1.3.6.1.4.1.1991.1.2.9.1.7.1.1INTEGER (1..48)read-onlycurrent
snPimVInterfaceType
OBJECT-TYPE
The type of PIM virtual interface, whether it uses a tunnel or a physical interface.
1.3.6.1.4.1.1991.1.2.9.1.7.1.2INTEGER {tunnel(1), subnet(2)}read-writecurrent
snPimVInterfaceLocalAddress
OBJECT-TYPE
The IP address of the local end of this PIM virtual interface.
1.3.6.1.4.1.1991.1.2.9.1.7.1.3IpAddressread-writecurrent
snPimVInterfaceLocalSubnetMask
OBJECT-TYPE
The network mask for the IP address of the PIM virtual interface. For a tunnel, this should be 0.0.0.0.
1.3.6.1.4.1.1991.1.2.9.1.7.1.4IpAddressread-onlycurrent
snPimVInterfaceRemoteAddress
OBJECT-TYPE
The IP address of the remote end of this PIM virtual interface.
1.3.6.1.4.1.1991.1.2.9.1.7.1.5IpAddressread-writecurrent
snPimVInterfaceDR
OBJECT-TYPE
The Designated Router on this PIM virtual interface. For point-to-point interfaces, this object has the value 0.0.0.0.
1.3.6.1.4.1.1991.1.2.9.1.7.1.6IpAddressread-onlycurrent
snPimVInterfaceTtlThreshold
OBJECT-TYPE
This is the minimum time-to-live value to forward the packets out of this interface.
1.3.6.1.4.1.1991.1.2.9.1.7.1.7INTEGER (1..31)read-writecurrent
snPimVInterfaceStatus
OBJECT-TYPE
This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative. valid(2)....Setting it to 'valid' has the effect of changing the row to operative.
1.3.6.1.4.1.1991.1.2.9.1.7.1.8INTEGER {invalid(1), valid(2), delete(3), create(4), modify(5)}read-writecurrent
snPimVInterfaceMode
OBJECT-TYPE
The configured mode of this PIM interface.
1.3.6.1.4.1.1991.1.2.9.1.7.1.9INTEGER {dense(1), sparse(2)}read-writecurrent
snPimNeighborTable
OBJECT-TYPE
The (conceptual) table listing the router's PIM neighbors. snPimEnable must be 'enabled' before this table is read.
1.3.6.1.4.1.1991.1.2.9.1.8not-accessiblecurrent
snPimNeighborEntry
OBJECT-TYPE
An entry (conceptual row) in the snPimNeighborTable.
1.3.6.1.4.1.1991.1.2.9.1.8.1not-accessiblecurrent
snPimNeighborEntryIndex
OBJECT-TYPE
The table entry index.
1.3.6.1.4.1.1991.1.2.9.1.8.1.1Integer32read-onlycurrent
snPimNeighborVifIndex
OBJECT-TYPE
The value of VifIndex for the virtual interface used to reach this PIM neighbor.
1.3.6.1.4.1.1991.1.2.9.1.8.1.2Integer32read-onlycurrent
snPimNeighborAddress
OBJECT-TYPE
The IP address of the PIM neighbor for which this entry contains information.
1.3.6.1.4.1.1991.1.2.9.1.8.1.3IpAddressread-onlycurrent
snPimNeighborUpTime
OBJECT-TYPE
The time since this PIM neighbor (last) became a neighbor of the local router.
1.3.6.1.4.1.1991.1.2.9.1.8.1.4TimeTicksread-onlycurrent
snPimNeighborExpiryTime
OBJECT-TYPE
The minimum time remaining before this PIM neighbor will be aged out.
1.3.6.1.4.1.1991.1.2.9.1.8.1.5TimeTicksread-onlycurrent
snPimVIfStatTable
OBJECT-TYPE
The (conceptual) table listing the router's PIM virtual interface statistical counters. snPimEnable must be 'enabled' before this table is read.
1.3.6.1.4.1.1991.1.2.9.1.9not-accessiblecurrent
snPimVIfStatEntry
OBJECT-TYPE
An entry (conceptual row) in the snPimVIfStatTable.
1.3.6.1.4.1.1991.1.2.9.1.9.1not-accessiblecurrent
snPimVIfStatVifIndex
OBJECT-TYPE
The ifIndex value of this PIM virtual interface.
1.3.6.1.4.1.1991.1.2.9.1.9.1.1INTEGER (1..32)read-onlycurrent
snPimVIfStatInJoinPkts
OBJECT-TYPE
The number of join packets that have arrived on the PIM virtual interface.
1.3.6.1.4.1.1991.1.2.9.1.9.1.2Counter32read-onlycurrent
snPimVIfStatOutJoinPkts
OBJECT-TYPE
The number of join packets that have been sent on the PIM virtual interface.
1.3.6.1.4.1.1991.1.2.9.1.9.1.3Counter32read-onlycurrent
snPimVIfStatDiscardJoinPkts
OBJECT-TYPE
The number of join packets that have been discarded by the PIM virtual interface.
1.3.6.1.4.1.1991.1.2.9.1.9.1.4Counter32read-onlycurrent
snPimVIfStatInPrunePkts
OBJECT-TYPE
The number of prune packets that have arrived on the PIM virtual interface.
1.3.6.1.4.1.1991.1.2.9.1.9.1.5Counter32read-onlycurrent
snPimVIfStatOutPrunePkts
OBJECT-TYPE
The number of prune packets that have been sent on the PIM virtual interface.
1.3.6.1.4.1.1991.1.2.9.1.9.1.6Counter32read-onlycurrent
snPimVIfStatDiscardPrunePkts
OBJECT-TYPE
The number of prune packets that have been discarded by the PIM virtual interface.
1.3.6.1.4.1.1991.1.2.9.1.9.1.7Counter32read-onlycurrent
snPimVIfStatInAssertPkts
OBJECT-TYPE
The number of assert packets that have arrived on the PIM virtual interface.
1.3.6.1.4.1.1991.1.2.9.1.9.1.8Counter32read-onlycurrent
snPimVIfStatOutAssertPkts
OBJECT-TYPE
The number of assert packets that have been sent on the PIM virtual interface.
1.3.6.1.4.1.1991.1.2.9.1.9.1.9Counter32read-onlycurrent
snPimVIfStatDiscardAssertPkts
OBJECT-TYPE
The number of assert packets that have been discarded by the PIM virtual interface.
1.3.6.1.4.1.1991.1.2.9.1.9.1.10Counter32read-onlycurrent
snPimVIfStatInHelloPkts
OBJECT-TYPE
The number of hello packets that have arrived on the PIM virtual interface.
1.3.6.1.4.1.1991.1.2.9.1.9.1.11Counter32read-onlycurrent
snPimVIfStatOutHelloPkts
OBJECT-TYPE
The number of hello packets that have been sent on the PIM virtual interface.
1.3.6.1.4.1.1991.1.2.9.1.9.1.12Counter32read-onlycurrent
snPimVIfStatDiscardHelloPkts
OBJECT-TYPE
The number of hello packets that have been discarded by the PIM virtual interface.
1.3.6.1.4.1.1991.1.2.9.1.9.1.13Counter32read-onlycurrent
snPimVIfStatInGraftPkts
OBJECT-TYPE
The number of graft packets that have arrived on the PIM virtual interface.
1.3.6.1.4.1.1991.1.2.9.1.9.1.14Counter32read-onlycurrent
snPimVIfStatOutGraftPkts
OBJECT-TYPE
The number of graft packets that have been sent on the PIM virtual interface.
1.3.6.1.4.1.1991.1.2.9.1.9.1.15Counter32read-onlycurrent
snPimVIfStatDiscardGraftPkts
OBJECT-TYPE
The number of graft packets that have been discarded by the PIM virtual interface.
1.3.6.1.4.1.1991.1.2.9.1.9.1.16Counter32read-onlycurrent
snPimVIfStatInGraftAckPkts
OBJECT-TYPE
The number of graft acknowledge packets that have arrived on the PIM virtual interface.
1.3.6.1.4.1.1991.1.2.9.1.9.1.17Counter32read-onlycurrent
snPimVIfStatOutGraftAckPkts
OBJECT-TYPE
The number of graft acknowledge packets that have been sent on the PIM virtual interface.
1.3.6.1.4.1.1991.1.2.9.1.9.1.18Counter32read-onlycurrent
snPimVIfStatDiscardGraftAckPkts
OBJECT-TYPE
The number of graft acknowledge packets that have been discarded by the PIM virtual interface.
1.3.6.1.4.1.1991.1.2.9.1.9.1.19Counter32read-onlycurrent
snPimSMMIBObjects
OBJECT-IDENTITY
1.3.6.1.4.1.1991.1.2.9.2
snPimJoinPruneInterval
OBJECT-TYPE
The default interval in seconds at which periodic PIM-SM Join/Prune messages are to be sent. snPimEnable must be 'enabled' before this table is read or writen.
1.3.6.1.4.1.1991.1.2.9.2.1INTEGER (10..3600)read-writecurrent
snPimCandidateBSRTable
OBJECT-TYPE
Candidate Bootstrap Router information.
1.3.6.1.4.1.1991.1.2.9.2.2not-accessiblecurrent
snPimCandidateBSREntry
OBJECT-TYPE
An entry (conceptual row) in the snPimCandidateBSRTable.
1.3.6.1.4.1.1991.1.2.9.2.2.1not-accessiblecurrent
snPimCandidateBSRPortID
OBJECT-TYPE
The IP address of the PIM interface. The bit 0 to bit 7: port number. The bit 8 to bit 11: slot number.
1.3.6.1.4.1.1991.1.2.9.2.2.1.1Integer32read-writecurrent
snPimCandidateBSRIPAddress
OBJECT-TYPE
The (unicast) address of the Candidate BSR.
1.3.6.1.4.1.1991.1.2.9.2.2.1.2IpAddressread-onlycurrent
snPimCandidateBSRHashMaskLen
OBJECT-TYPE
The hash mask value for this router as a candidate bootstrap router.
1.3.6.1.4.1.1991.1.2.9.2.2.1.3INTEGER (1..32)read-writecurrent
snPimCandidateBSRPreference
OBJECT-TYPE
The preference value for this router as a candidate bootstrap router.
1.3.6.1.4.1.1991.1.2.9.2.2.1.4INTEGER (0..255)read-writecurrent
snPimRPSetTable
OBJECT-TYPE
The (conceptual) table listing PIM information for candidate Rendezvous Points (RPs) for IP multicast groups. When the local router is the BSR, this information is obtained from received Candidate-RP-Advertisements. When the local router is not the BSR, this information is obtained from received RP-Set messages. snPimEnable must be 'enabled' before this table is read or writen.
1.3.6.1.4.1.1991.1.2.9.2.3not-accessiblecurrent
snPimRPSetEntry
OBJECT-TYPE
An entry (conceptual row) in the snPimRPSetTable.
1.3.6.1.4.1.1991.1.2.9.2.3.1not-accessiblecurrent
snPimRPSetGroupAddress
OBJECT-TYPE
The IP multicast group address which, when combined with snPimRPSetGroupMask, gives the group prefix for which this entry contains information about the Candidate-RP.
1.3.6.1.4.1.1991.1.2.9.2.3.1.1IpAddressread-onlycurrent
snPimRPSetMask
OBJECT-TYPE
The multicast group address mask which, when combined with snPimRPSetGroupAddress, gives the group prefix for which this entry contains information about the Candidate-RP.
1.3.6.1.4.1.1991.1.2.9.2.3.1.2IpAddressread-onlycurrent
snPimRPSetIPAddress
OBJECT-TYPE
The IP address of the Candidate-RP.
1.3.6.1.4.1.1991.1.2.9.2.3.1.3IpAddressread-onlycurrent
snPimRPSetHoldTime
OBJECT-TYPE
The holdtime, in seconds, of a Candidate-RP. If the local router is not the BSR, this value is 0.
1.3.6.1.4.1.1991.1.2.9.2.3.1.4INTEGER (0..255)read-onlycurrent
snPimCandidateRPTable
OBJECT-TYPE
The (conceptual) table listing the IP multicast groups for which the local router is to advertise itself as a Candidate-RP. If this table is empty, then the local router will advertise itself as a Candidate-RP for all groups snPimEnable must be 'enabled' before this table is read or writen.
1.3.6.1.4.1.1991.1.2.9.2.4not-accessiblecurrent
snPimCandidateRPEntry
OBJECT-TYPE
An entry (conceptual row) in the snPimCandidateRPTable.
1.3.6.1.4.1.1991.1.2.9.2.4.1not-accessiblecurrent
snPimCandidateRPGroupAddress
OBJECT-TYPE
The IP multicast group address which, when combined with snPimCandidateRPGroupMask, identifies a group prefix for which the local router will advertise itself as a Candidate-RP.
1.3.6.1.4.1.1991.1.2.9.2.4.1.1IpAddressread-onlycurrent
snPimCandidateRPMask
OBJECT-TYPE
The multicast group address mask which, when combined with snPimCandidateRPGroupMask, identifies a group prefix for which the local router will advertise itself as a Candidate-RP.
1.3.6.1.4.1.1991.1.2.9.2.4.1.2IpAddressread-onlycurrent
snPimCandidateRPIPAddress
OBJECT-TYPE
The (unicast) address of the interface which will be advertised as a Candidate-RP.
1.3.6.1.4.1.1991.1.2.9.2.4.1.3IpAddressread-writecurrent
snPimCandidateRPRowStatus
OBJECT-TYPE
The status of this row, by which new entries may be created, or old entries deleted from this table. This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row other(1)....some other case valid(2)....the row exists and is valid
1.3.6.1.4.1.1991.1.2.9.2.4.1.4INTEGER {noSuch(0), other(1), valid(2), delete(3), create(4), modify(5)}read-writecurrent
snLoopbackIntfConfigTable
OBJECT-TYPE
Loopback Interface Config table.
1.3.6.1.4.1.1991.1.2.13.1not-accessiblecurrent
snLoopbackIntfConfigEntry
OBJECT-TYPE
An entry in the Loopback Interface Config table.
1.3.6.1.4.1.1991.1.2.13.1.1not-accessiblecurrent
snLoopbackIntfConfigPortIndex
OBJECT-TYPE
The port index for Loopback Interface config entry.
1.3.6.1.4.1.1991.1.2.13.1.1.1INTEGER (1..8)read-onlycurrent
snLoopbackIntfMode
OBJECT-TYPE
The Loopback Interface mode.
1.3.6.1.4.1.1991.1.2.13.1.1.2INTEGER {disabled(0), enabled(1)}read-writecurrent
snLoopbackIntfRowStatus
OBJECT-TYPE
This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid
1.3.6.1.4.1.1991.1.2.13.1.1.3INTEGER {invalid(1), valid(2), delete(3), create(4), modify(5)}read-writecurrent