MIBs Depot

E5-110-MIB

Registered at
1.3.6.1.4.1.6321.1.2.3.1
Namespace
calix
Source file
E5-110-MIB
Digest
sha256:25da0a2645e67ff17c50e6460231557a7b71b21a6fb93d291d3e332375b9bc54

Imports

FromSymbols
BRIDGE-MIBBridgeId, MacAddress, Timeout, dot1dBasePort
IF-MIBifIndex
P-BRIDGE-MIBdot1dTrafficClass
Q-BRIDGE-MIBPortList, VlanIndex, dot1qVlanIndex
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP
SNMPv2-SMICounter32, Counter64, Gauge32, IpAddress, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, enterprises, iso
SNMPv2-TCDisplayString, PhysAddress, RowStatus, TEXTUAL-CONVENTION

Imported by

4 module(s) in this corpus import this one.

Load order

Every file a consumer needs in order to load this module, dependencies first.

BRIDGE-MIB
E5-110-MIB
IANAifType-MIB
IF-MIB
P-BRIDGE-MIB
Q-BRIDGE-MIB
RFC1158-MIB
RFC1271-MIB
RMON-MIB
RMON2-MIB
SNMP-FRAMEWORK-MIB
SNMPv2-CONF
SNMPv2-MIB
SNMPv2-SMI
SNMPv2-TC
TOKEN-RING-RMON-MIB

Under this module's arcs

Where the registration tree carries on below this module.

ArcNameModule
1.3.6.1.4.1.6321.1.2.3.1.12trap
1.3.6.1.4.1.6321.1.2.3.1.97aesSeriesCommon
1.3.6.1.4.1.6321.1.2.3.1.98iesSeriesCommon
1.3.6.1.4.1.6321.1.2.3.1.99accessSwitchCommonATM

Objects

NameOIDSyntaxAccessStatus
calixNetworks
OBJECT-IDENTITY
1.3.6.1.4.1.6321
calixRegistrations
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1
calixProducts
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2
e5x100
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3
e5x110
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1
alarmconf
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.2
alarmOps
OBJECT-TYPE
The manager sets the corresponding bit value to 1 to start the operation and the agent clears the object to zero when the operation is successfully completed. The various bit positions are: BIT 1: clear BIT 2: cutoff
1.3.6.1.4.1.6321.1.2.3.1.2.1INTEGERread-writecurrent
alarmConfTable
OBJECT-TYPE
This table includes alarm configuration.
1.3.6.1.4.1.6321.1.2.3.1.2.2not-accessiblecurrent
alarmConfEntry
OBJECT-TYPE
An entry in alarmConfTable.
1.3.6.1.4.1.6321.1.2.3.1.2.2.1not-accessiblecurrent
alarmConfId
OBJECT-TYPE
5000:adslLine_up 5001:adslLine_down 5002:adslPerf_lol_thresh 5003:adslPerf_lof_thresh 5004:adslPerf_los_thresh 5005:adslPerf_lop_thresh 5006:adslPerf_es_thresh 5007:adslPerf_ses_thresh 5008:adslPerf_uas_thresh 5009:adslAtuc_loftrap 5010:adslAtuc_lostrap 5011:adslAtur_loftrap 5012:adslAtur_lostrap 5013:adslAtur_lprtrap 5014:ad_dhcp_rt_full 5015:ad_dhcp_dm_conflict 5016:ad_dhcp_entry_full 5017:ad_dhcp_ip_dup 5018:ad_dhcp_mac_dup 10000:eqptVol_err 10001:eqptEqpttemp_err 10002:eqptFan_err 10003:eqptHw_rtc_fail 10004:eqptHw_mon_fail 10005:eqptCold_start 10006:eqptWarm_start 10007:eqptAlm_input 10008:eqptI2c_err 10009:eqptAlm_input2 10010:eqptAlm_input3 15000:sysReboot 15001:sysAco 15002:sysAlm_clear 15003:sysLogin_fail 15004:sysAnti_spoofing 15005:sysAlm_svrty_change 20000:enetUp 20001:enetDown
1.3.6.1.4.1.6321.1.2.3.1.2.2.1.1INTEGERread-onlycurrent
alarmConfFacility
OBJECT-TYPE
Alarm facility.
1.3.6.1.4.1.6321.1.2.3.1.2.2.1.2INTEGER {local1(1), local2(2), local3(3), local4(4), local5(5), local6(6), local7(7)}read-writecurrent
alarmConfTarget
OBJECT-TYPE
The destination which alarms are reported to. Set the bit to 1 to enable the target. BIT 1: snmp trap BIT 2: syslog
1.3.6.1.4.1.6321.1.2.3.1.2.2.1.3INTEGERread-writecurrent
alarmConfSeverity
OBJECT-TYPE
Alarm severity
1.3.6.1.4.1.6321.1.2.3.1.2.2.1.4INTEGER {critical(1), major(2), minor(3), info(4)}read-writecurrent
alarmConfClearable
OBJECT-TYPE
Setting the object to one indicates that the alarm is to be cleared when user submits alarm clear.
1.3.6.1.4.1.6321.1.2.3.1.2.2.1.5INTEGER {clearable(1), unclearable(2)}read-writecurrent
alarmCurrTable
OBJECT-TYPE
This table includes current alarm information.
1.3.6.1.4.1.6321.1.2.3.1.2.3not-accessiblecurrent
alarmCurrEntry
OBJECT-TYPE
An entry in alarmCurrTable.
1.3.6.1.4.1.6321.1.2.3.1.2.3.1not-accessiblecurrent
alarmCurrIndex
OBJECT-TYPE
Index of the alarm.
1.3.6.1.4.1.6321.1.2.3.1.2.3.1.1INTEGERread-onlycurrent
alarmCurrOccurTime
OBJECT-TYPE
Alarm occurence time (in hundredths of a second) since the system was last re-initialized.
1.3.6.1.4.1.6321.1.2.3.1.2.3.1.2TimeTicksread-onlycurrent
alarmCurrTrapOid
OBJECT-TYPE
Trap OID of the alarm.
1.3.6.1.4.1.6321.1.2.3.1.2.3.1.3OBJECT IDENTIFIERread-onlycurrent
alarmCurrParam1
OBJECT-TYPE
The 1st parameter of the alarm.
1.3.6.1.4.1.6321.1.2.3.1.2.3.1.4INTEGERread-onlycurrent
alarmCurrParam2
OBJECT-TYPE
The 2nd parameter of the alarm.
1.3.6.1.4.1.6321.1.2.3.1.2.3.1.5INTEGERread-onlycurrent
alarmCurrParam3
OBJECT-TYPE
The 3rd parameter of the alarm.
1.3.6.1.4.1.6321.1.2.3.1.2.3.1.6INTEGERread-onlycurrent
alarmCurrParam4
OBJECT-TYPE
The 4th parameter of the alarm.
1.3.6.1.4.1.6321.1.2.3.1.2.3.1.7INTEGERread-onlycurrent
alarmCurrParam5
OBJECT-TYPE
The 5th parameter of the alarm.
1.3.6.1.4.1.6321.1.2.3.1.2.3.1.8INTEGERread-onlycurrent
alarmCurrParam6
OBJECT-TYPE
The 6th parameter of the alarm.
1.3.6.1.4.1.6321.1.2.3.1.2.3.1.9INTEGERread-onlycurrent
alarmCurrParam7
OBJECT-TYPE
The 7th parameter of the alarm.
1.3.6.1.4.1.6321.1.2.3.1.2.3.1.10INTEGERread-onlycurrent
alarmCurrParam8
OBJECT-TYPE
The 8th parameter of the alarm.
1.3.6.1.4.1.6321.1.2.3.1.2.3.1.11INTEGERread-onlycurrent
alarmCurrTimeDescr
OBJECT-TYPE
The string representation of occurence time (YYYY/MM/DD HH:MM:SS).
1.3.6.1.4.1.6321.1.2.3.1.2.3.1.12DisplayStringread-onlycurrent
alarmCurrSeverity
OBJECT-TYPE
The severity of the alarm.
1.3.6.1.4.1.6321.1.2.3.1.2.3.1.13INTEGER {critical(1), major(2), minor(3), info(4)}read-onlycurrent
alarmCurrDescr
OBJECT-TYPE
The description of the alarm.
1.3.6.1.4.1.6321.1.2.3.1.2.3.1.14DisplayStringread-onlycurrent
alarmSeverityPortTable
OBJECT-TYPE
This table includes the configuration of alarm reporting severity threshold for each port.
1.3.6.1.4.1.6321.1.2.3.1.2.4not-accessiblecurrent
alarmSeverityPortEntry
OBJECT-TYPE
An entry in alarmSeverityPortTable.
1.3.6.1.4.1.6321.1.2.3.1.2.4.1not-accessiblecurrent
severityThresh
OBJECT-TYPE
The minimum alarm severity that is reported.
1.3.6.1.4.1.6321.1.2.3.1.2.4.1.1INTEGER {critical(1), major(2), minor(3), info(4)}read-writecurrent
diagnostic
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.4
selt
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.4.3
seltTarget
OBJECT-TYPE
IfIndex of the port which would be performed single end loopback test.
1.3.6.1.4.1.6321.1.2.3.1.4.3.1INTEGERread-writecurrent
seltOps
OBJECT-TYPE
The manager sets the object to 1 to start the selt and the agent clears the object to zero when selt is successfully completed.
1.3.6.1.4.1.6321.1.2.3.1.4.3.2INTEGERread-writecurrent
seltStatus
OBJECT-TYPE
Status description of the selt result.
1.3.6.1.4.1.6321.1.2.3.1.4.3.3DisplayStringread-onlycurrent
seltCableType
OBJECT-TYPE
The cable type that selt result indicates.
1.3.6.1.4.1.6321.1.2.3.1.4.3.4INTEGER {awg24(1), awg26(2)}read-onlycurrent
seltLoopEstimateLengthFt
OBJECT-TYPE
The estimated loop length that selt result indicates.
1.3.6.1.4.1.6321.1.2.3.1.4.3.5INTEGERread-onlycurrent
seltLoopEstimateLengthMeter
OBJECT-TYPE
The estimated loop length that selt result indicates.
1.3.6.1.4.1.6321.1.2.3.1.4.3.6INTEGERread-onlycurrent
multicast
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.7
igmpEnable
OBJECT-TYPE
Enable/disable IGMP protocol.
1.3.6.1.4.1.6321.1.2.3.1.7.1INTEGER {enableProxy(1), enableSnooping(2), disable(3)}read-writecurrent
mcastBandwidth
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.7.4
mcastDefaultBandwidth
OBJECT-TYPE
Default bandwidth requirement for a multicast channel.
1.3.6.1.4.1.6321.1.2.3.1.7.4.1INTEGER (1..100000)read-writecurrent
maxNumOfMcastBw
OBJECT-TYPE
The maximum number of row entries that user can create in mcastBwTable.
1.3.6.1.4.1.6321.1.2.3.1.7.4.2INTEGERread-onlycurrent
mcastBwTable
OBJECT-TYPE
This table defines bandwidth budget for a range of multicast IP channels.
1.3.6.1.4.1.6321.1.2.3.1.7.4.3not-accessiblecurrent
mcastBwEntry
OBJECT-TYPE
An entry of mcastBwTable.
1.3.6.1.4.1.6321.1.2.3.1.7.4.3.1not-accessiblecurrent
mcastBwIndex
OBJECT-TYPE
The index which specify the entry.
1.3.6.1.4.1.6321.1.2.3.1.7.4.3.1.1INTEGERread-onlycurrent
mcastBwStartIp
OBJECT-TYPE
The start multicast IP of the bandwidth control range.
1.3.6.1.4.1.6321.1.2.3.1.7.4.3.1.2IpAddressread-onlycurrent
mcastBwEndIp
OBJECT-TYPE
The end multicast IP of the bandwidth control range.
1.3.6.1.4.1.6321.1.2.3.1.7.4.3.1.3IpAddressread-onlycurrent
mcastBwBandwidth
OBJECT-TYPE
The bandwidth budget for the multicast IP channels.
1.3.6.1.4.1.6321.1.2.3.1.7.4.3.1.4INTEGERread-createcurrent
mcastBwRowStatus
OBJECT-TYPE
The row status of the entry.
1.3.6.1.4.1.6321.1.2.3.1.7.4.3.1.5RowStatusread-createcurrent
mcastBwPortTable
OBJECT-TYPE
This table specify the multicast bandwidth control of the port.
1.3.6.1.4.1.6321.1.2.3.1.7.4.4not-accessiblecurrent
mcastBwPortEntry
OBJECT-TYPE
An entry of mcastBwPortTable.
1.3.6.1.4.1.6321.1.2.3.1.7.4.4.1not-accessiblecurrent
mcastBwPortEnable
OBJECT-TYPE
Enable/disable multicast bandwidth control for a port.
1.3.6.1.4.1.6321.1.2.3.1.7.4.4.1.1INTEGER {enable(1), disable(2)}read-writecurrent
mcastBwPortBandwidth
OBJECT-TYPE
Set bandwidth threshold for a port.
1.3.6.1.4.1.6321.1.2.3.1.7.4.4.1.2INTEGERread-writecurrent
igmpCount
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.7.5
igmpCountPortTable
OBJECT-TYPE
This table specify the IGMP count limiting of the port.
1.3.6.1.4.1.6321.1.2.3.1.7.5.1not-accessiblecurrent
igmpCountPortEntry
OBJECT-TYPE
An entry of igmpCountPortTable.
1.3.6.1.4.1.6321.1.2.3.1.7.5.1.1not-accessiblecurrent
igmpCountPortEnable
OBJECT-TYPE
Enable/disable IGMP count limiting for a port.
1.3.6.1.4.1.6321.1.2.3.1.7.5.1.1.1INTEGER {enable(1), disable(2)}read-writecurrent
igmpCountPortLimit
OBJECT-TYPE
The maximum allowed IGMP report count for a port.
1.3.6.1.4.1.6321.1.2.3.1.7.5.1.1.2INTEGER (0..16)read-writecurrent
mvlan
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.7.6
maxNumOfMvlan
OBJECT-TYPE
The maximum number of row entries that user can create in mvlanTable.
1.3.6.1.4.1.6321.1.2.3.1.7.6.1INTEGERread-onlycurrent
mvlanTable
OBJECT-TYPE
A table containing static configuration information for each multicast VLAN configured into the device.
1.3.6.1.4.1.6321.1.2.3.1.7.6.2not-accessiblecurrent
mvlanEntry
OBJECT-TYPE
An entry of mvlanTable.
1.3.6.1.4.1.6321.1.2.3.1.7.6.2.1not-accessiblecurrent
mvlanIndex
OBJECT-TYPE
The VLAN-ID refering to this VLAN.
1.3.6.1.4.1.6321.1.2.3.1.7.6.2.1.1VlanIndexread-onlycurrent
mvlanName
OBJECT-TYPE
An administratively assigned string, which may be used to identify the VLAN.
1.3.6.1.4.1.6321.1.2.3.1.7.6.2.1.2DisplayString (SIZE(0..31))read-createcurrent
mvlanEgressPorts
OBJECT-TYPE
The set of ports which are permanently assigned to the egress list for this multicast VLAN.
1.3.6.1.4.1.6321.1.2.3.1.7.6.2.1.3PortListread-createcurrent
mvlanUntaggedPorts
OBJECT-TYPE
The set of ports which should transmit egress packets for this multicast VLAN as untagged.
1.3.6.1.4.1.6321.1.2.3.1.7.6.2.1.4PortListread-createcurrent
mvlanRowStatus
OBJECT-TYPE
This object indicates the status of this entry.
1.3.6.1.4.1.6321.1.2.3.1.7.6.2.1.5RowStatusread-createcurrent
mvlanTranslateTable
OBJECT-TYPE
A table that contains multicast to VLAN translation.
1.3.6.1.4.1.6321.1.2.3.1.7.6.3not-accessiblecurrent
mvlanTranslateEntry
OBJECT-TYPE
An entry of mvlanTranslateTable.
1.3.6.1.4.1.6321.1.2.3.1.7.6.3.1not-accessiblecurrent
mvlanTranslateIndex
OBJECT-TYPE
The index which specif the entry.
1.3.6.1.4.1.6321.1.2.3.1.7.6.3.1.1INTEGERread-onlycurrent
mvlanTranslateStartIp
OBJECT-TYPE
The start IP of the multicast VLAN translation.
1.3.6.1.4.1.6321.1.2.3.1.7.6.3.1.2IpAddressread-writecurrent
mvlanTranslateEndIp
OBJECT-TYPE
The end IP of the multicast VLAN translation.
1.3.6.1.4.1.6321.1.2.3.1.7.6.3.1.3IpAddressread-writecurrent
queryVid
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.7.7
maxNumOfQryVid
OBJECT-TYPE
The maximum number of row entries that user can create in qryVidConfTable.
1.3.6.1.4.1.6321.1.2.3.1.7.7.1INTEGERread-onlycurrent
qryVidConfTable
OBJECT-TYPE
This table defines statically set VLANs used for response IGMP report.
1.3.6.1.4.1.6321.1.2.3.1.7.7.2not-accessiblecurrent
qryVidConfEntry
OBJECT-TYPE
An entry in qryVidConfTable.
1.3.6.1.4.1.6321.1.2.3.1.7.7.2.1not-accessiblecurrent
qryVid
OBJECT-TYPE
VLAN ID.
1.3.6.1.4.1.6321.1.2.3.1.7.7.2.1.1INTEGERread-onlycurrent
qryVidRowStatus
OBJECT-TYPE
This object indicates the status of this entry.
1.3.6.1.4.1.6321.1.2.3.1.7.7.2.1.2RowStatusread-createcurrent
qryVidStatusTable
OBJECT-TYPE
This table shows statically set or dynamically learned VLANs used for response IGMP report.
1.3.6.1.4.1.6321.1.2.3.1.7.7.3not-accessiblecurrent
qryVidStatusEntry
OBJECT-TYPE
An entry in qryVidStatusTable.
1.3.6.1.4.1.6321.1.2.3.1.7.7.3.1not-accessiblecurrent
qryVidType
OBJECT-TYPE
VLAN type.
1.3.6.1.4.1.6321.1.2.3.1.7.7.3.1.1INTEGER {static(1), dynamic(2)}read-onlycurrent
igmpVersion
OBJECT-TYPE
Setting IGMP version.
1.3.6.1.4.1.6321.1.2.3.1.7.9INTEGER {v2(1), v3(2)}read-writecurrent
igmpLeaveMode
OBJECT-TYPE
Configure IGMP leave message handling mode.
1.3.6.1.4.1.6321.1.2.3.1.7.10INTEGER {immediateLeave(1), lastMemberQuery(2)}read-writecurrent
igmpTimer
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.7.11
igmpQryInterval
OBJECT-TYPE
Set IGMP query interval, 10~1000 in seconds.
1.3.6.1.4.1.6321.1.2.3.1.7.11.1INTEGER (10..1000)read-writecurrent
igmpRobust
OBJECT-TYPE
Set IGMP query Robustness, 1~5.
1.3.6.1.4.1.6321.1.2.3.1.7.11.2INTEGER (1..5)read-writecurrent
igmpQryRespInterval
OBJECT-TYPE
Set IGMP query response interval, 1~100 in 100 milliseconds.
1.3.6.1.4.1.6321.1.2.3.1.7.11.3INTEGER (1..100)read-writecurrent
igmpLastMemQryInterval
OBJECT-TYPE
Set IGMP Last Member Query interval, 1~5 in 100 milliseconds.
1.3.6.1.4.1.6321.1.2.3.1.7.11.4INTEGER (1..5)read-writecurrent
igmpLastMemQryRobust
OBJECT-TYPE
Set Last Member Query Robustness, 1~5.
1.3.6.1.4.1.6321.1.2.3.1.7.11.5INTEGER (1..5)read-writecurrent
auditQuery
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.7.12
auditQryEnable
OBJECT-TYPE
Enable/disable IGMP audit query.
1.3.6.1.4.1.6321.1.2.3.1.7.12.1INTEGER {enable(1), disable(2)}read-writecurrent
auditQryInterval
OBJECT-TYPE
Set IGMP Audit Query Interval, 1~4 in 100 milliseconds.
1.3.6.1.4.1.6321.1.2.3.1.7.12.2INTEGER (1..4)read-writecurrent
auditQryRobust
OBJECT-TYPE
Set IGMP Audit Query Robustness, 1~5.
1.3.6.1.4.1.6321.1.2.3.1.7.12.3INTEGER (1..5)read-writecurrent
igmpProfile
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.7.13
maxNumberOfIgmpProfiles
OBJECT-TYPE
The max number of IGMP profiles in the system.
1.3.6.1.4.1.6321.1.2.3.1.7.13.1INTEGERread-onlycurrent
igmpProfileTable
OBJECT-TYPE
A table that contains IGMP Profiles.
1.3.6.1.4.1.6321.1.2.3.1.7.13.2not-accessiblecurrent
igmpProfileEntry
OBJECT-TYPE
The entry of IGMP Profile table.
1.3.6.1.4.1.6321.1.2.3.1.7.13.2.1not-accessiblecurrent
igmpProfileName
OBJECT-TYPE
The IGMP Profile name.
1.3.6.1.4.1.6321.1.2.3.1.7.13.2.1.1DisplayString (SIZE(1..31))read-onlycurrent
igmpProfileEnable
OBJECT-TYPE
Enable/disable IGMP Profile.
1.3.6.1.4.1.6321.1.2.3.1.7.13.2.1.2INTEGER {enable(1), disable(2)}read-writecurrent
igmpProfileMaxGroup
OBJECT-TYPE
Set maximum allowed multicast group, 1~16.
1.3.6.1.4.1.6321.1.2.3.1.7.13.2.1.3INTEGER (1..16)read-writecurrent
igmpProfileRowStatus
OBJECT-TYPE
The row status of the IGMP Profile entry.
1.3.6.1.4.1.6321.1.2.3.1.7.13.2.1.4RowStatusread-createcurrent
igmpFilterTable
OBJECT-TYPE
A table that contains IGMP Filters.
1.3.6.1.4.1.6321.1.2.3.1.7.13.3not-accessiblecurrent
igmpFilterEntry
OBJECT-TYPE
The entry of IGMP Filter table.
1.3.6.1.4.1.6321.1.2.3.1.7.13.3.1not-accessiblecurrent
igmpFilterIndex
OBJECT-TYPE
The index which specifies the filter rule.
1.3.6.1.4.1.6321.1.2.3.1.7.13.3.1.1INTEGERread-onlycurrent
igmpFilterStartIp
OBJECT-TYPE
The start IP of the filter rule.
1.3.6.1.4.1.6321.1.2.3.1.7.13.3.1.2IpAddressread-createcurrent
igmpFilterEndIp
OBJECT-TYPE
The end IP of the filter rule.
1.3.6.1.4.1.6321.1.2.3.1.7.13.3.1.3IpAddressread-createcurrent
igmpProfilePortTable
OBJECT-TYPE
This table specifies the IGMP Profile of the port.
1.3.6.1.4.1.6321.1.2.3.1.7.13.4not-accessiblecurrent
igmpProfilePortEntry
OBJECT-TYPE
An entry in igmpProfilePortTable.
1.3.6.1.4.1.6321.1.2.3.1.7.13.4.1not-accessiblecurrent
igmpProfilePortProfile
OBJECT-TYPE
The IGMP Profile of the port.
1.3.6.1.4.1.6321.1.2.3.1.7.13.4.1.1OCTET STRING (SIZE(1..31))read-writecurrent
port
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.8
subrPortTable
OBJECT-TYPE
This table includes subscriber attributes for the port.
1.3.6.1.4.1.6321.1.2.3.1.8.1not-accessiblecurrent
subrPortEntry
OBJECT-TYPE
An entry in subrPortTable.
1.3.6.1.4.1.6321.1.2.3.1.8.1.1not-accessiblecurrent
subrPortName
OBJECT-TYPE
Name of the subscriber.
1.3.6.1.4.1.6321.1.2.3.1.8.1.1.1DisplayString (SIZE(0..31))read-writecurrent
subrPortTel
OBJECT-TYPE
Telephone number of the subscriber.
1.3.6.1.4.1.6321.1.2.3.1.8.1.1.2DisplayString (SIZE(0..15))read-writecurrent
adslPort
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.8.2
adslLineConfTable
OBJECT-TYPE
This table includes common attributes describing the ADSL line.
1.3.6.1.4.1.6321.1.2.3.1.8.2.1not-accessiblecurrent
adslLineConfEntry
OBJECT-TYPE
An entry in adslLineConfTable.
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1not-accessiblecurrent
adslLineConfAdslMode
OBJECT-TYPE
G.lite and T1.413 are only applicable to annex A board. ETSI is only applicable to annex B board.
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.1INTEGER {gDotLite(1), gDotDmt(2), t1Dot413(3), auto(4), etsi(5), adsl2(6), adsl2Plus(7)}read-writecurrent
adslLineConfAnnexL
OBJECT-TYPE
Enable/disable annex L for the port(Only in AnnexA).
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.2INTEGER {enableNarrowMode(1), enableWideMode(2), disable(3)}read-writecurrent
adslLineConfAnnexM
OBJECT-TYPE
Enable/disable annex M for the port(For BCM AnnexA solution).
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.3INTEGER {enable(1), disable(2)}read-writecurrent
adslLineConfAnnexI
OBJECT-TYPE
Enable/disable annex I for the port(For BCM AnnexA solution).
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.4INTEGER {enable(1), disable(2)}read-writecurrent
adslLineConfOptionMask
OBJECT-TYPE
The semantic for each bit is: BIT 1 : Disable Trellis BIT 2 : Disable Reed-Solomon BIT 3 : Disable upstream bitswap BIT 4 : Disable downstream bitswap BIT 5 : Disable 1-bit constellation BIT 6 : Disable transmit windowing BIT 7 : Disable s=0.5 support (ADSL1 only) BIT 8 : Disable G.lite rate limit (ADSL1 only) BIT 9 : Enable Nitro BIT 10: Enable US PHYR BIT 11: ENABLE DS PHYR
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.5INTEGERread-writecurrent
adslLineConfPowerMgmt
OBJECT-TYPE
Enable/disable power management for the port.
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.6INTEGER {enableL2(2), disable(3)}read-writecurrent
adslLineConfPowerMode
OBJECT-TYPE
The power mode of the ADSL line.
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.7INTEGER {fix(1), priorityToPower(2), priorityToRate(3)}read-writecurrent
adslLineConfAturMaxTxPower
OBJECT-TYPE
The maximum allowed transmit power of ATU-R.
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.8INTEGER (-130..200)read-writecurrent
adslLineConfAtucMaxTxPower
OBJECT-TYPE
The maximum allowed transmit power of ATU-C.
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.9INTEGER (-50..200)read-writecurrent
adslLineConfMaxRxPower
OBJECT-TYPE
The maximum aggregate received power.
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.10INTEGER (-255..255)read-writecurrent
adslLineConfAturCarrierMask
OBJECT-TYPE
The upstream carrier mask. For CTLM AnnexA solution, bin is from 0 to 31; CTLM AnnexB solution, bin is from 0 to 63; BCM solution, bin is from 0 to 63. Bit set to 1 indicates the bin is masked off.
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.11OCTET STRINGread-writecurrent
adslLineConfAtucCarrierMask0
OBJECT-TYPE
The downstream carrier mask. For CTLM AnnexA solution, bin is from 32 to 255; CTLM AnnexB solution, bin is from 64 to 255; BCM solution, bin is from 32 to 255. Bit set to 1 indicates the bin is masked off.
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.12OCTET STRINGread-writecurrent
adslLineConfAtucCarrierMask1
OBJECT-TYPE
The downstream carrier mask from bin 256 to 511. Bit set to 1 indicates the bin is masked off.
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.13OCTET STRINGread-writecurrent
adslLineConfAturInp
OBJECT-TYPE
The upstream Impulse Noise Protection minimum setting in unit of DMT symbol. For CTLM solution, user can set value from 1 ~ 4, but for BCM solution, user can set value from 1 ~ 7.
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.14INTEGER {zero(1), zeroPointFive(2), one(3), two(4), four(5), eight(6), sixteen(7)}read-writecurrent
adslLineConfAtucInp
OBJECT-TYPE
The downstream Impulse Noise Protection minimum setting in unit of DMT symbol. For CTLM solution, user can set value from 1 ~ 4, but for BCM solution, user can set value from 1 ~ 7.
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.15INTEGER {zero(1), zeroPointFive(2), one(3), two(4), four(5), eight(6), sixteen(7)}read-writecurrent
adslLineConfL0Time
OBJECT-TYPE
Set the minimum time in seconds that the ADSL line must stay in L0 power mode before changing to the L2 power mode. For CTLM solution, the range is 120 ~ 65535; for BCM solution, the range is 10 ~ 65535.
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.16INTEGERread-writecurrent
adslLineConfL2Time
OBJECT-TYPE
Set minimum time in seconds that the ADSL line must stay in the L2 power mode before reducing the power again in the L2 power mode. For CTLM solution, the range is 60 ~ 65535; for BCM solution, the range is 10 ~ 65535.
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.17INTEGERread-writecurrent
adslLineConfL2ATPR
OBJECT-TYPE
Set the maximum Aggregate Transmit Power Reduction (ATPR) in decibels (dB) that is permitted in a L2 power reduction. The system can gradually decrease the ADSL line transmission power while it is in the L2 power mode. This is the largest individual power reduction allowed in the L2 power mode. For CTLM solution, the range is 1 ~ 5(dB); for BCM solution, the range is 0 ~ 15(dB).
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.18INTEGERread-writecurrent
adslLineConfL2ATPRT
OBJECT-TYPE
the maximum Aggregate Transmit Power Reduction Total (ATPRT) in decibels (dB) that is permitted in the L2 power mode. This is the total transmit power decrease that is allowed to occur in the L2 power mode. For CTLM solution, the range is 1 ~ 40(dB); for BCM solution, the range is 0 ~ 15(dB).
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.19INTEGERread-writecurrent
adslLineConfMaxL2Rate
OBJECT-TYPE
configured maximum L2 rate. (32~4096 Kbps, 4 Kbps resolution. For CTLM solution, 0 for system assign; for BCM solution, default:4096.)
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.20INTEGERread-writecurrent
adslLineConfMinL2Rate
OBJECT-TYPE
configured minimum L2 rate. (32~4096 Kbps, 4 Kbps resolution, For CTLM solution, 0 for system assign; for BCM solution, default:32.)
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.21INTEGERread-writecurrent
adslLineConfL0toL2Rate
OBJECT-TYPE
configured transition L0 to L2 rate. (<=min_l2rate/2 and >= 16 Kbps, For CTLM solution, 0 for system assign; for BCM solution, default:16.)
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.22INTEGERread-writecurrent
adslLineConfNitro
OBJECT-TYPE
Enable/disable nitro mode for the port(For BCM solution).
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.23INTEGER {enable(1), disable(2)}read-writecurrent
adslLineConfUSPhyr
OBJECT-TYPE
Enable/disable Upstream PHYR for the port(For BCM solution).
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.24INTEGER {enable(1), disable(2)}read-writecurrent
adslLineConfDSPhyr
OBJECT-TYPE
Enable/disable Downstream PHYR for the port(For BCM solution).
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.25INTEGER {enable(1), disable(2)}read-writecurrent
adslPortBatchSet
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.8.2.3
adslPortTarget
OBJECT-TYPE
The managed object is used for identify the target on which the port configuration should be performed. The target is encoded as: Byte 1: 0, Reserved(chaises) Byte 2~3: 0,0 Reserved(slot) Byte 4: 0, reserved Byte 5~11:each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc.
1.3.6.1.4.1.6321.1.2.3.1.8.2.3.1OCTET STRINGread-writecurrent
adslPortOps
OBJECT-TYPE
The managed object is for ADSL line configuration. When the EMS wants to issue the desired operation, the EMS shall send SNMP-SET message to set the corresponding bit value to be 1. The various bit positions are: BIT 1: enable port BIT 2: disable port BIT 3: set ADSL mode BIT 4: set line profile BIT 5: set alarm profile BIT 6: enable Annex L to be narrow mode(Only in AnnexA) BIT 7: enable Annex L to be wide mode(Only in AnnexA) BIT 8: disable Annex L(Only in AnnexA) BIT 9: enable Annex M (For BCM AnnexA solution) BIT 10: disable Annex M (For BCM AnnexA solution) BIT 11: enable Annex I (For BCM AnnexA solution) BIT 12: disable Annex I (For BCM AnnexA solution) BIT 13: set option mask BIT 14: enable power management mode to be L2 BIT 15: enable power management mode to be L2 BIT 16: disable power management mode BIT 17: set power mode to be fixed BIT 18: set power mode to be priority to power BIT 19: set power mode to be priority to rate BIT 20: set ATU-R max Tx power BIT 21: set ATU-C max Tx power BIT 22: set max Rx power BIT 23: set ATU-R carrier mask BIT 24: set ATU-C carrier mask BIT 25: set ATU-R INP minimum setting BIT 26: set ATU-C INP minimum setting
1.3.6.1.4.1.6321.1.2.3.1.8.2.3.2INTEGERread-writecurrent
adslPortOps2
OBJECT-TYPE
The managed object is for ADSL line configuration. When the EMS wants to issue the desired operation, the EMS shall send SNMP-SET message to set the corresponding bit value to be 1. The various bit positions are: BIT 1: set L0 Time BIT 2: set L2 Time BIT 3: set L2 ATPR BIT 4: set L2 ATPRT BIT 5: set maximum L2 rate BIT 6: set minimum L2 rate BIT 7: set transition L0 to L2 rate
1.3.6.1.4.1.6321.1.2.3.1.8.2.3.3INTEGERread-writecurrent
adslModeForBatchSet
OBJECT-TYPE
G.lite and T1.413 are only applicable to annex A board. ETSI is only applicable to annex B board.
1.3.6.1.4.1.6321.1.2.3.1.8.2.3.4INTEGER {gDotLite(1), gDotDmt(2), t1Dot413(3), auto(4), etsi(5), adsl2(6), adsl2Plus(7)}read-writecurrent
adslLineProfileForBatchSet
OBJECT-TYPE
The ADSL line profile.
1.3.6.1.4.1.6321.1.2.3.1.8.2.3.5DisplayString (SIZE(1..31))read-writecurrent
adslAlarmProfileForBatchSet
OBJECT-TYPE
The ADSL alarm profile.
1.3.6.1.4.1.6321.1.2.3.1.8.2.3.6DisplayString (SIZE(1..31))read-writecurrent
adslOptionMaskForBatchSet
OBJECT-TYPE
The semantic for each bit is identical to the object adslLineConfOptionMask.
1.3.6.1.4.1.6321.1.2.3.1.8.2.3.7INTEGERread-writecurrent
adslAturMaxTxPowerForBatchSet
OBJECT-TYPE
The maximum allowed transmit power of ATU-R.
1.3.6.1.4.1.6321.1.2.3.1.8.2.3.8INTEGER (-130..200)read-writecurrent
adslAtucMaxTxPowerForBatchSet
OBJECT-TYPE
The maximum allowed transmit power of ATU-C.
1.3.6.1.4.1.6321.1.2.3.1.8.2.3.9INTEGER (-50..200)read-writecurrent
adslMaxRxPowerForBatchSet
OBJECT-TYPE
The maximum aggregate received power.
1.3.6.1.4.1.6321.1.2.3.1.8.2.3.10INTEGER (-255..255)read-writecurrent
adslAturCarrierMaskForBatchSet
OBJECT-TYPE
The upstream carrier mask.For CTLM AnnexA solution, bin is from 0 to 31; CTLM AnnexB solution, bin is from 0 to 63; BCM solution, bin is from 0 to 63. Bit set to 1 indicates the bin is masked off.
1.3.6.1.4.1.6321.1.2.3.1.8.2.3.11OCTET STRINGread-writecurrent
adslAtucCarrierMask0ForBatchSet
OBJECT-TYPE
The downstream carrier mask from bin 32 to 255. Bit set to 1 indicates the bin is masked off.
1.3.6.1.4.1.6321.1.2.3.1.8.2.3.12OCTET STRINGread-writecurrent
adslAtucCarrierMask1ForBatchSet
OBJECT-TYPE
The downstream carrier mask from bin 256 to 511. Bit set to 1 indicates the bin is masked off.
1.3.6.1.4.1.6321.1.2.3.1.8.2.3.13OCTET STRINGread-writecurrent
adslAturInpForBatchSet
OBJECT-TYPE
The upstream Impulse Noise Protection minimum setting in unit of DMT symbol. For CTLM solution, user can set value from 1 ~ 4, but for BCM solution, user can set value from 1 ~ 7.
1.3.6.1.4.1.6321.1.2.3.1.8.2.3.14INTEGER {zero(1), zeroPointFive(2), one(3), two(4), four(5), eight(6), sixteen(7)}read-writecurrent
adslAtucInpForBatchSet
OBJECT-TYPE
The downstream Impulse Noise Protection minimum setting in unit of DMT symbol. For CTLM solution, user can set value from 1 ~ 4, but for BCM solution, user can set value from 1 ~ 7.
1.3.6.1.4.1.6321.1.2.3.1.8.2.3.15INTEGER {zero(1), zeroPointFive(2), one(3), two(4), four(5), eight(6), sixteen(7)}read-writecurrent
adslL0TimeForBatchSet
OBJECT-TYPE
Set the minimum time in seconds that the ADSL line must stay in L0 power mode before changing to the L2 power mode. For CTLM solution, the range is 120 ~ 65535; for BCM solution, the range is 10 ~ 65535.
1.3.6.1.4.1.6321.1.2.3.1.8.2.3.16INTEGERread-writecurrent
adslL2TimeForBatchSet
OBJECT-TYPE
Set minimum time in seconds that the ADSL line must stay in the L2 power mode before reducing the power again in the L2 power mode. For CTLM solution, the range is 60 ~ 65535; for BCM solution, the range is 10 ~ 65535.
1.3.6.1.4.1.6321.1.2.3.1.8.2.3.17INTEGERread-writecurrent
adslL2ATPRForBatchSet
OBJECT-TYPE
Set the maximum Aggregate Transmit Power Reduction (ATPR) in decibels (dB) that is permitted in a L2 power reduction. The system can gradually decrease the ADSL line transmission power while it is in the L2 power mode. This is the largest individual power reduction allowed in the L2 power mode. For CTLM solution, the range is 1 ~ 5(dB); for BCM solution, the range is 0 ~ 15(dB).
1.3.6.1.4.1.6321.1.2.3.1.8.2.3.18INTEGERread-writecurrent
adslL2ATPRTForBatchSet
OBJECT-TYPE
the maximum Aggregate Transmit Power Reduction Total (ATPRT) in decibels (dB) that is permitted in the L2 power mode. This is the total transmit power decrease that is allowed to occur in the L2 power mode. For CTLM solution, the range is 1 ~ 40(dB); for BCM solution, the range is 0 ~ 15(dB).
1.3.6.1.4.1.6321.1.2.3.1.8.2.3.19INTEGERread-writecurrent
adslMaxL2RateForBatchSet
OBJECT-TYPE
configured maximum L2 rate. (32~4096 Kbps, 4 Kbps resolution. For CTLM solution, 0 for system assign; for BCM solution, default:4096.)
1.3.6.1.4.1.6321.1.2.3.1.8.2.3.20INTEGERread-writecurrent
adslMinL2RateForBatchSet
OBJECT-TYPE
configured minimum L2 rate. (32~4096 Kbps, 4 Kbps resolution, For CTLM solution, 0 for system assign; for BCM solution, default:32.)
1.3.6.1.4.1.6321.1.2.3.1.8.2.3.21INTEGERread-writecurrent
adslL0toL2RateForBatchSet
OBJECT-TYPE
configured transition L0 to L2 rate. (<=min_l2rate/2 and >= 16 Kbps, For CTLM solution, 0 for system assign; for BCM solution, default:16.)
1.3.6.1.4.1.6321.1.2.3.1.8.2.3.22INTEGERread-writecurrent
adslLineStatusTable
OBJECT-TYPE
This table includes the ADSL line status.
1.3.6.1.4.1.6321.1.2.3.1.8.2.4not-accessiblecurrent
adslLineStatusEntry
OBJECT-TYPE
An entry in adslLineStatusTable.
1.3.6.1.4.1.6321.1.2.3.1.8.2.4.1not-accessiblecurrent
adslLineStatusMode
OBJECT-TYPE
The link up mode of the ADSL line.
1.3.6.1.4.1.6321.1.2.3.1.8.2.4.1.1INTEGER {gDotLite(1), gDotDmt(2), t1Dot413(3), etsi(4), adsl2(5), adsl2Plus(6), none(7)}read-onlycurrent
adslLineUpTime
OBJECT-TYPE
The link up time of the ADSL line, in unit of seconds
1.3.6.1.4.1.6321.1.2.3.1.8.2.4.1.2INTEGERread-onlycurrent
powerMgmtParamTable
OBJECT-TYPE
This table defines L0 to L2 power transition parameters.
1.3.6.1.4.1.6321.1.2.3.1.8.2.5not-accessiblecurrent
powerMgmtParamEntry
OBJECT-TYPE
An entry in powerMgmtParamTable.
1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1not-accessiblecurrent
powerMgmtL0Time
OBJECT-TYPE
The object specifies the minimum time in L0 mode before L2 mode may be entered.
1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1.1INTEGERread-writecurrent
powerMgmtL2Time
OBJECT-TYPE
The object specifies the minimum time in L2 mode before trimming and in between power trims.
1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1.2INTEGERread-writecurrent
powerMgmtL2Atpr
OBJECT-TYPE
The maximum Aggregate Transmit Power Reduction.
1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1.3INTEGERread-writecurrent
powerMgmtL2Atprt
OBJECT-TYPE
The maximum Aggregate Transmit Power Reduction Total.
1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1.4INTEGERread-writecurrent
powerMgmtL2MinRate
OBJECT-TYPE
The object specifies the minimum L2 rate.
1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1.5INTEGERread-writecurrent
powerMgmtL2MaxRate
OBJECT-TYPE
The object specifies the maximum L2 rate.
1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1.6INTEGERread-writecurrent
powerMgmtL2ThreshRate
OBJECT-TYPE
The object specifies the rate threshold that triggers the line entering L0 or L2 mode.
1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1.7INTEGERread-writecurrent
powerMgmtPSDTable
OBJECT-TYPE
This table provides the PSD setting for both ATU-C and ATU-R.
1.3.6.1.4.1.6321.1.2.3.1.8.2.6not-accessiblecurrent
powerMgmtPSDEntry
OBJECT-TYPE
An entry in powerMgmtPSDTable.
1.3.6.1.4.1.6321.1.2.3.1.8.2.6.1not-accessiblecurrent
powerMgmtAtucMaxPSD
OBJECT-TYPE
The object specifies the maximum ATU-C PSD.
1.3.6.1.4.1.6321.1.2.3.1.8.2.6.1.1INTEGERread-writecurrent
powerMgmtAturMaxPSD
OBJECT-TYPE
The object specifies the maximum ATU-R PSD.
1.3.6.1.4.1.6321.1.2.3.1.8.2.6.1.2INTEGERread-writecurrent
pvc
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.8.4
maxNumOfPvcs
OBJECT-TYPE
The maximum number of PVCs which could be created on a port.
1.3.6.1.4.1.6321.1.2.3.1.8.4.1INTEGERread-onlycurrent
pvcTable
OBJECT-TYPE
This table includes PVC configuration.
1.3.6.1.4.1.6321.1.2.3.1.8.4.2not-accessiblecurrent
pvcEntry
OBJECT-TYPE
An entry in pvcTable.
1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1not-accessiblecurrent
pvcVpi
OBJECT-TYPE
VPI of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.1INTEGER (0..255)read-onlycurrent
pvcVci
OBJECT-TYPE
VCI of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.2INTEGER (1..65535)read-onlycurrent
pvcPvid
OBJECT-TYPE
Default VID of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.3VlanIndexread-onlycurrent
pvcPriority
OBJECT-TYPE
802.1p default priority of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.5INTEGER (0..7)read-createcurrent
pvcProfileDS
OBJECT-TYPE
The value of this object identifies the row in the atmProfileTable, which applies for this pvc in DS side.
1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.6DisplayString (SIZE(1..31))read-createcurrent
pvcRowStatus
OBJECT-TYPE
This object is used to create a new row or delete an existing row in this table.
1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.7RowStatusread-createcurrent
pvcProfileUS
OBJECT-TYPE
The value of this object identifies the row in the atmProfileTable, which applies for this pvc in US side.
1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.8DisplayString (SIZE(1..31))read-createcurrent
pvcAcName
OBJECT-TYPE
Access concentrator name for paepvc.
1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.11DisplayStringread-createcurrent
pvcServiceName
OBJECT-TYPE
Service name for paepvc.
1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.12DisplayStringread-createcurrent
pvcHelloTime
OBJECT-TYPE
The system will close the PVC if there are not any LCP echo messages passed through during the LCP hello time.
1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.13INTEGERread-createcurrent
pvcStateTable
OBJECT-TYPE
This table show current PVC status.
1.3.6.1.4.1.6321.1.2.3.1.8.4.3read-onlycurrent
pvcStateEntry
OBJECT-TYPE
An entry in pvcStateTable.
1.3.6.1.4.1.6321.1.2.3.1.8.4.3.1read-onlycurrent
pvcStateVpi
OBJECT-TYPE
VPI of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.4.3.1.1INTEGER (0..255)read-onlycurrent
pvcStateVci
OBJECT-TYPE
VCI of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.4.3.1.2INTEGER (1..65535)read-onlycurrent
pvcStatePvid
OBJECT-TYPE
Default VID of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.4.3.1.3VlanIndexread-onlycurrent
pvcStatePriority
OBJECT-TYPE
802.1p default priority of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.4.3.1.4INTEGER (0..7)read-onlycurrent
pvcStateChannelType
OBJECT-TYPE
The value of this object identifies the channel type at runtime.
1.3.6.1.4.1.6321.1.2.3.1.8.4.3.1.8DisplayString (SIZE(1..31))read-onlycurrent
pvcStateEncap
OBJECT-TYPE
The value of this object identifies the channel encapsulation at runtime.
1.3.6.1.4.1.6321.1.2.3.1.8.4.3.1.9DisplayString (SIZE(1..31))read-onlycurrent
pvcUsRateLimitTable
OBJECT-TYPE
This table defines the upstream rate limit for each PVC.
1.3.6.1.4.1.6321.1.2.3.1.8.4.4not-accessiblecurrent
pvcUsRateLimitEntry
OBJECT-TYPE
An entry in pvcUsRateLimitTable.
1.3.6.1.4.1.6321.1.2.3.1.8.4.4.1not-accessiblecurrent
pvcUsRateLimitEnable
OBJECT-TYPE
Enable/disable upstream rate limit for a PVC.
1.3.6.1.4.1.6321.1.2.3.1.8.4.4.1.1INTEGER {enable(1), disable(2)}read-writecurrent
pvcUsRateLimit
OBJECT-TYPE
Upstream rate limit in Kbps for a PVC.
1.3.6.1.4.1.6321.1.2.3.1.8.4.4.1.2INTEGERread-writecurrent
ppvc
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.8.5
maxNumOfPriorityPvcs
OBJECT-TYPE
The maximum number of priority PVCs which could be created on a port.
1.3.6.1.4.1.6321.1.2.3.1.8.5.1INTEGERread-onlycurrent
ppvcTable
OBJECT-TYPE
This table includes priority PVC configuration.
1.3.6.1.4.1.6321.1.2.3.1.8.5.2not-accessiblecurrent
ppvcEntry
OBJECT-TYPE
An entry in ppvcTable.
1.3.6.1.4.1.6321.1.2.3.1.8.5.2.1not-accessiblecurrent
ppvcVpi
OBJECT-TYPE
VPI of the ppvc.
1.3.6.1.4.1.6321.1.2.3.1.8.5.2.1.1INTEGER (0..255)read-onlycurrent
ppvcVci
OBJECT-TYPE
VCI of the ppvc.
1.3.6.1.4.1.6321.1.2.3.1.8.5.2.1.2INTEGER (1..65535)read-onlycurrent
ppvcPvid
OBJECT-TYPE
Default VID of the ppvc.
1.3.6.1.4.1.6321.1.2.3.1.8.5.2.1.3VlanIndexread-onlycurrent
ppvcEncap
OBJECT-TYPE
Encapsulation of the ppvc.
1.3.6.1.4.1.6321.1.2.3.1.8.5.2.1.4INTEGER {llc(1), vc(2)}read-createcurrent
ppvcPriority
OBJECT-TYPE
802.1p default priority of the ppvc.
1.3.6.1.4.1.6321.1.2.3.1.8.5.2.1.5INTEGER (0..7)read-createcurrent
ppvcRowStatus
OBJECT-TYPE
This object is used to create a new row or delete an existing row in this table.
1.3.6.1.4.1.6321.1.2.3.1.8.5.2.1.6RowStatusread-createcurrent
ppvcMemberTable
OBJECT-TYPE
This table includes priority PVC member configuration.
1.3.6.1.4.1.6321.1.2.3.1.8.5.4not-accessiblecurrent
ppvcMemberEntry
OBJECT-TYPE
An entry in ppvcMemberTable.
1.3.6.1.4.1.6321.1.2.3.1.8.5.4.1not-accessiblecurrent
ppvcMemberVpi
OBJECT-TYPE
VPI of the member ppvc.
1.3.6.1.4.1.6321.1.2.3.1.8.5.4.1.1INTEGER (0..255)read-onlycurrent
ppvcMemberVci
OBJECT-TYPE
VCI of the member ppvc.
1.3.6.1.4.1.6321.1.2.3.1.8.5.4.1.2INTEGER (1..65535)read-onlycurrent
ppvcMemberPriority
OBJECT-TYPE
802.1p default priority of the member ppvc.
1.3.6.1.4.1.6321.1.2.3.1.8.5.4.1.3INTEGER (0..7)read-onlycurrent
ppvcMemberProfileDS
OBJECT-TYPE
The profile of the member ppvc in DS side.
1.3.6.1.4.1.6321.1.2.3.1.8.5.4.1.4DisplayString (SIZE(1..31))read-createcurrent
ppvcMemberRowStatus
OBJECT-TYPE
This object is used to create a new row or delete an existing row in this table.
1.3.6.1.4.1.6321.1.2.3.1.8.5.4.1.5RowStatusread-createcurrent
ppvcMemberProfileUS
OBJECT-TYPE
The profile of the member ppvc in US side.
1.3.6.1.4.1.6321.1.2.3.1.8.5.4.1.6DisplayString (SIZE(1..31))read-createcurrent
rpvc
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.8.8
rpvcGatewayTable
OBJECT-TYPE
This table includes Routed Gateway configuration.
1.3.6.1.4.1.6321.1.2.3.1.8.8.1not-accessiblecurrent
rpvcGatewayEntry
OBJECT-TYPE
An entry in Routed Gateway table.
1.3.6.1.4.1.6321.1.2.3.1.8.8.1.1not-accessiblecurrent
rpvcGatewayIp
OBJECT-TYPE
IP of RPVC gateway.
1.3.6.1.4.1.6321.1.2.3.1.8.8.1.1.1IpAddressread-onlycurrent
rpvcGatewayVlanId
OBJECT-TYPE
Vlan id send to this RPVC gateway.
1.3.6.1.4.1.6321.1.2.3.1.8.8.1.1.2VlanIndexread-writecurrent
rpvcGatewayRowStatus
OBJECT-TYPE
This object is used to create a new row or delete an existing row in this table.
1.3.6.1.4.1.6321.1.2.3.1.8.8.1.1.3RowStatusread-createcurrent
rpvcGatewayPriority
OBJECT-TYPE
802.1p p bit send to this RPVC gateway.
1.3.6.1.4.1.6321.1.2.3.1.8.8.1.1.4INTEGERread-writecurrent
rpvcTable
OBJECT-TYPE
This table includes RPVC configuration.
1.3.6.1.4.1.6321.1.2.3.1.8.8.2not-accessiblecurrent
rpvcEntry
OBJECT-TYPE
An entry in rpvcTable.
1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1not-accessiblecurrent
rpvcVpi
OBJECT-TYPE
VPI of the rpvc.
1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.1INTEGER (0..255)read-onlycurrent
rpvcVci
OBJECT-TYPE
VCI of the rpvc.
1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.2INTEGER (1..65535)read-onlycurrent
rpvcDSProfile
OBJECT-TYPE
The down stream profile of the rpvc.
1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.3DisplayString (SIZE(1..31))read-createcurrent
rpvcUSProfile
OBJECT-TYPE
The up stream profile of the rpvc.
1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.4DisplayString (SIZE(1..31))read-createcurrent
rpvcIp
OBJECT-TYPE
The IP of the rpvc.
1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.5IpAddressread-onlycurrent
rpvcNetmask
OBJECT-TYPE
The IP mask of the rpvc IP.
1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.6IpAddressread-onlycurrent
rpvcGatewayIpAddress
OBJECT-TYPE
The gateway IP of rpvc.
1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.7IpAddressread-createcurrent
rpvcRowStatus
OBJECT-TYPE
This object is used to create a new row or delete an existing row in this table.
1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.8RowStatusread-createcurrent
rpvcRouteDomainTable
OBJECT-TYPE
This table includes RPVC route domain configuration.
1.3.6.1.4.1.6321.1.2.3.1.8.8.3not-accessiblecurrent
rpvcRouteDomainEntry
OBJECT-TYPE
An entry in rpvcRouteDomainTable.
1.3.6.1.4.1.6321.1.2.3.1.8.8.3.1not-accessiblecurrent
rpvcRouteDomainVpi
OBJECT-TYPE
VPI of the rpvc.
1.3.6.1.4.1.6321.1.2.3.1.8.8.3.1.1INTEGER (0..255)read-onlycurrent
rpvcRouteDomainVci
OBJECT-TYPE
VCI of the rpvc.
1.3.6.1.4.1.6321.1.2.3.1.8.8.3.1.2INTEGER (1..65535)read-onlycurrent
rpvcRouteDomainIp
OBJECT-TYPE
The route domain IP.
1.3.6.1.4.1.6321.1.2.3.1.8.8.3.1.3IpAddressread-onlycurrent
rpvcRouteDomainNetmask
OBJECT-TYPE
The IP mask of the route domain IP.
1.3.6.1.4.1.6321.1.2.3.1.8.8.3.1.4IpAddressread-onlycurrent
rpvcRouteDomainRowStatus
OBJECT-TYPE
This object is used to create a new row or delete an existing row in this table.
1.3.6.1.4.1.6321.1.2.3.1.8.8.3.1.5RowStatusread-createcurrent
rpvcArpAgingTime
OBJECT-TYPE
Set RPVC ARP proxy aging time 10..10000 seconds, 0 to disable againg.
1.3.6.1.4.1.6321.1.2.3.1.8.8.4INTEGERread-writecurrent
rpvcArpFlush
OBJECT-TYPE
Flush the RPVC ARP proxy table.
1.3.6.1.4.1.6321.1.2.3.1.8.8.5INTEGER {enable(1)}read-writecurrent
dsBcastDisableTable
OBJECT-TYPE
This table includes Down Stream Bcast configuration.
1.3.6.1.4.1.6321.1.2.3.1.8.9not-accessiblecurrent
dsBcastDisableEntry
OBJECT-TYPE
An entry in Down Stream Bcast table.
1.3.6.1.4.1.6321.1.2.3.1.8.9.1not-accessiblecurrent
dsBcastDisableVlanId
OBJECT-TYPE
downstream broadcast disabled vid.
1.3.6.1.4.1.6321.1.2.3.1.8.9.1.1INTEGERread-onlycurrent
dsBcastDisableRowStatus
OBJECT-TYPE
This object is used to create a new row or delete an existing row in this table.
1.3.6.1.4.1.6321.1.2.3.1.8.9.1.2RowStatusread-createcurrent
paepvc
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.8.10
paepvcTable
OBJECT-TYPE
This table includes PPPoAoE PVC configuration.
1.3.6.1.4.1.6321.1.2.3.1.8.10.1not-accessiblecurrent
paepvcEntry
OBJECT-TYPE
An entry of paepvcTable.
1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1not-accessiblecurrent
paepvcVpi
OBJECT-TYPE
VPI of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.1INTEGER (0..255)read-onlycurrent
paepvcVci
OBJECT-TYPE
VCI of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.2INTEGER (1..65535)read-onlycurrent
paepvcPvid
OBJECT-TYPE
Default VID of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.3VlanIndexread-onlycurrent
paepvcPriority
OBJECT-TYPE
802.1p default priority of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.5INTEGER (0..7)read-createcurrent
paepvcProfileDS
OBJECT-TYPE
The value of this object identifies the row in the atmProfileTable, which applies for this pvc in DS side.
1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.6DisplayString (SIZE(1..31))read-createcurrent
paepvcAcName
OBJECT-TYPE
Access concentrator name.
1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.7DisplayStringread-createcurrent
paepvcServiceName
OBJECT-TYPE
Service name.
1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.8DisplayStringread-createcurrent
paepvcHelloTime
OBJECT-TYPE
The system will close the PVC if there are not any LCP echo messages passed through during the LCP hello time.
1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.9INTEGERread-createcurrent
paepvcRowStatus
OBJECT-TYPE
This object is used to create a new row or delete an existing row in this table.
1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.10RowStatusread-createcurrent
paepvcProfileUS
OBJECT-TYPE
The value of this object identifies the row in the atmProfileTable, which applies for this pvc in US side.
1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.11DisplayString (SIZE(1..31))read-createcurrent
paepvcCvid
OBJECT-TYPE
Default C-VID of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.12VlanIndexread-createcurrent
paepvcCPriority
OBJECT-TYPE
802.1p default C-priority of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.13INTEGER (0..7)read-createcurrent
tlspvc
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.8.11
tlspvcTable
OBJECT-TYPE
This table includes Transparent LAN Service (TLS) PVC configuration.
1.3.6.1.4.1.6321.1.2.3.1.8.11.1not-accessiblecurrent
tlspvcEntry
OBJECT-TYPE
An entry of tlspvcTable.
1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1not-accessiblecurrent
tlspvcVpi
OBJECT-TYPE
VPI of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1.1INTEGER (0..255)read-onlycurrent
tlspvcVci
OBJECT-TYPE
VCI of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1.2INTEGER (1..65535)read-onlycurrent
tlspvcSvid
OBJECT-TYPE
s-tag VLAN ID of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1.3VlanIndexread-onlycurrent
tlspvcSpriority
OBJECT-TYPE
s-tag priority of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1.5INTEGER (0..7)read-createcurrent
tlspvcProfileDS
OBJECT-TYPE
The value of this object identifies the row in the atmProfileTable, which applies for this pvc in DS side.
1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1.6DisplayString (SIZE(1..31))read-createcurrent
tlspvcRowStatus
OBJECT-TYPE
This object is used to create a new row or delete an existing row in this table.
1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1.7RowStatusread-createcurrent
tlspvcProfileUS
OBJECT-TYPE
The value of this object identifies the row in the atmProfileTable, which applies for this pvc in US side.
1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1.8DisplayString (SIZE(1..31))read-createcurrent
ipbpvc
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.8.12
ipbpvcDomainTable
OBJECT-TYPE
This table includes ipbpvc domain configuration. This table is supported by R3.00 and later versions.
1.3.6.1.4.1.6321.1.2.3.1.8.12.1not-accessiblecurrent
ipbpvcDomainEntry
OBJECT-TYPE
An entry of ipbpvcDomainTable.
1.3.6.1.4.1.6321.1.2.3.1.8.12.1.1not-accessiblecurrent
ipbpvcDomainName
OBJECT-TYPE
Name of the domain.
1.3.6.1.4.1.6321.1.2.3.1.8.12.1.1.1OCTET STRINGread-onlycurrent
ipbpvcDomainRowStatus
OBJECT-TYPE
Row status of the table.
1.3.6.1.4.1.6321.1.2.3.1.8.12.1.1.2RowStatusread-createcurrent
ipbpvcDomainVlanTable
OBJECT-TYPE
This table includes ipbpvc domain VLAN configuration. This table is supported by R3.00 and later versions.
1.3.6.1.4.1.6321.1.2.3.1.8.12.2not-accessiblecurrent
ipbpvcDomainVlanEntry
OBJECT-TYPE
An entry of ipbpvcDomainVlanTable.
1.3.6.1.4.1.6321.1.2.3.1.8.12.2.1not-accessiblecurrent
ipbpvcDomainVlanId
OBJECT-TYPE
Set VLAN to join or leave the specified domain.
1.3.6.1.4.1.6321.1.2.3.1.8.12.2.1.1VlanIndexread-onlycurrent
ipbpvcDomainDhcpVlanEnable
OBJECT-TYPE
Enable/disable DHCP VLAN in a domain.
1.3.6.1.4.1.6321.1.2.3.1.8.12.2.1.2INTEGER {enable(1), disable(2)}read-createcurrent
ipbpvcDomainVlanRowStatus
OBJECT-TYPE
Row status of the table used to create/delete an entry.
1.3.6.1.4.1.6321.1.2.3.1.8.12.2.1.3RowStatusread-createcurrent
ipbpvcEdgeRouterTable
OBJECT-TYPE
This table includes ipbpvc edge router configuration. This table is supported by R3.00 and later versions.
1.3.6.1.4.1.6321.1.2.3.1.8.12.3not-accessiblecurrent
ipbpvcEdgeRouterEntry
OBJECT-TYPE
An entry of ipbpvcEdgeRouterTable.
1.3.6.1.4.1.6321.1.2.3.1.8.12.3.1not-accessiblecurrent
ipbpvcEdgeRouterIp
OBJECT-TYPE
IP address of the edge router.
1.3.6.1.4.1.6321.1.2.3.1.8.12.3.1.1IpAddressread-onlycurrent
ipbpvcEdgeRouterVid
OBJECT-TYPE
VLAN ID of the edge router.
1.3.6.1.4.1.6321.1.2.3.1.8.12.3.1.2VlanIndexread-onlycurrent
ipbpvcEdgeRouterMask
OBJECT-TYPE
Netmask of the edge router.
1.3.6.1.4.1.6321.1.2.3.1.8.12.3.1.3INTEGERread-onlycurrent
ipbpvcEdgeRouterRowStatus
OBJECT-TYPE
Row status of the table used to create/delete an entry.
1.3.6.1.4.1.6321.1.2.3.1.8.12.3.1.4RowStatusread-createcurrent
ipbpvcInterfaceTable
OBJECT-TYPE
This table includes ipbpvc interface configuration. This table is supported by R3.00 and later versions.
1.3.6.1.4.1.6321.1.2.3.1.8.12.4not-accessiblecurrent
ipbpvcInterfaceEntry
OBJECT-TYPE
An entry of ipbpvcInterfaceTable.
1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1not-accessiblecurrent
ipbpvcInterfaceIp
OBJECT-TYPE
IP address of the interface.
1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1.1IpAddressread-onlycurrent
ipbpvcInterfaceMask
OBJECT-TYPE
Netmask of the interface.
1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1.2INTEGERread-onlycurrent
ipbpvcInterfaceVid
OBJECT-TYPE
VLAN ID of the interface.
1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1.3VlanIndexread-onlycurrent
ipbpvcInterfaceIfIndex
OBJECT-TYPE
IfIndex of the interface.
1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1.4INTEGERread-createcurrent
ipbpvcInterfaceVpi
OBJECT-TYPE
VPI of the interface.
1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1.5INTEGERread-createcurrent
ipbpvcInterfaceVci
OBJECT-TYPE
VCI of the interface.
1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1.6INTEGERread-createcurrent
ipbpvcInterfaceRowStatus
OBJECT-TYPE
Row status of the table used to create/delete an entry.
1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1.7RowStatusread-createcurrent
ipbpvcRouteTable
OBJECT-TYPE
This table includes ipbpvc route configuration. This table is supported by R3.00 and later versions.
1.3.6.1.4.1.6321.1.2.3.1.8.12.5not-accessiblecurrent
ipbpvcRouteEntry
OBJECT-TYPE
An entry of ipbpvcRouteTable.
1.3.6.1.4.1.6321.1.2.3.1.8.12.5.1not-accessiblecurrent
ipbpvcRouteIp
OBJECT-TYPE
IP address of the route.
1.3.6.1.4.1.6321.1.2.3.1.8.12.5.1.1IpAddressread-onlycurrent
ipbpvcRouteMask
OBJECT-TYPE
Netmask of the route.
1.3.6.1.4.1.6321.1.2.3.1.8.12.5.1.2INTEGERread-onlycurrent
ipbpvcRouteNextHop
OBJECT-TYPE
Next hop IP address of the route.
1.3.6.1.4.1.6321.1.2.3.1.8.12.5.1.3IpAddressread-onlycurrent
ipbpvcRouteMetric
OBJECT-TYPE
Metric of the route.
1.3.6.1.4.1.6321.1.2.3.1.8.12.5.1.4INTEGER (1..15)read-createcurrent
ipbpvcRoutePriority
OBJECT-TYPE
Priority of the route. Note that the default value of this object is 8, which means we keep the original priority of the packet(frame).
1.3.6.1.4.1.6321.1.2.3.1.8.12.5.1.5INTEGERread-createcurrent
ipbpvcRouteRowStatus
OBJECT-TYPE
Row status of the table used to create/delete an entry.
1.3.6.1.4.1.6321.1.2.3.1.8.12.5.1.6RowStatusread-createcurrent
ipbpvcTable
OBJECT-TYPE
This table includes ipbpvc configuration. This table is supported by R3.00 and later versions.
1.3.6.1.4.1.6321.1.2.3.1.8.12.6not-accessiblecurrent
ipbpvcEntry
OBJECT-TYPE
An entry of ipbpvcTable.
1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1not-accessiblecurrent
ipbpvcVpi
OBJECT-TYPE
VPI of the PVC.
1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.1INTEGERread-onlycurrent
ipbpvcVci
OBJECT-TYPE
VCI of the PVC.
1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.2INTEGERread-onlycurrent
ipbpvcPvid
OBJECT-TYPE
PVID of the PVC.
1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.3INTEGERread-onlycurrent
ipbpvcEncap
OBJECT-TYPE
Type of the PVC.
1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.4INTEGER {ipoe(1), reserved(2), ipoa(3)}read-createcurrent
ipbpvcPriority
OBJECT-TYPE
Priority of the PVC.
1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.5INTEGER (0..7)read-createcurrent
ipbpvcProfile
OBJECT-TYPE
Profile of the PVC.
1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.6OCTET STRINGread-createcurrent
ipbpvcRowStatus
OBJECT-TYPE
Row status of the table used to create/delete an entry.
1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.7INTEGERread-createcurrent
ipbpvcProfileUS
OBJECT-TYPE
US Profile of the PVC.
1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.8OCTET STRINGread-createcurrent
arpproxy
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.8.12.8
arpproxyAge
OBJECT-TYPE
Aging time of the ARP proxy. This object is supported by R3.00 and later versions.
1.3.6.1.4.1.6321.1.2.3.1.8.12.8.1INTEGER (10..10000)read-writecurrent
arpproxyFlush
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2
arpproxyFlushTarget
OBJECT-TYPE
The target whose ARP table to be flushed. This object is supported by R3.00 and later versions.
1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2.1INTEGER {all(1), edgerouter(2), interface(3)}read-writecurrent
arpproxyFlushOps
OBJECT-TYPE
Set the object to 1 to start flushing. This object is supported by R3.00 and later versions.
1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2.2INTEGERread-writecurrent
arpproxyFlushEdgeRouterIp
OBJECT-TYPE
Flush ARP table for the specified edge router. This object is supported by R3.00 and later versions.
1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2.3IpAddressread-writecurrent
arpproxyFlushEdgeRouterVid
OBJECT-TYPE
Flush ARP table for the specified edge router. This object is supported by R3.00 and later versions.
1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2.4VlanIndexread-writecurrent
arpproxyFlushInterfaceIp
OBJECT-TYPE
Flush ARP table for the specified interface. This object is supported by R3.00 and later versions.
1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2.5IpAddressread-writecurrent
arpproxyFlushInterfaceMask
OBJECT-TYPE
Flush ARP table for the specified interface. This object is supported by R3.00 and later versions.
1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2.6INTEGERread-writecurrent
arpproxyFlushInterfaceVid
OBJECT-TYPE
Flush ARP table for the specified interface. This object is supported by R3.00 and later versions.
1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2.7VlanIndexread-writecurrent
dtpvc
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.8.14
dtpvcTable
OBJECT-TYPE
This table includes Double Tagging (DT) PVC configuration.
1.3.6.1.4.1.6321.1.2.3.1.8.14.1not-accessiblecurrent
dtpvcEntry
OBJECT-TYPE
An entry of dtpvcTable.
1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1not-accessiblecurrent
dtpvcVpi
OBJECT-TYPE
VPI of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.1INTEGER (0..255)read-onlycurrent
dtpvcVci
OBJECT-TYPE
VCI of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.2INTEGER (1..65535)read-onlycurrent
dtpvcSvid
OBJECT-TYPE
s-tag VLAN ID of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.3VlanIndexread-onlycurrent
dtpvcSpriority
OBJECT-TYPE
s-tag priority of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.4INTEGER (0..7)read-createcurrent
dtpvcCvid
OBJECT-TYPE
c-tag VLAN ID of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.5VlanIndexread-createcurrent
dtpvcCpriority
OBJECT-TYPE
c-tag priority of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.6INTEGER (0..7)read-createcurrent
dtpvcDSProfile
OBJECT-TYPE
The value of this object identifies the row in the atmProfileTable, which applies for this dtpvc in DS side.
1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.7DisplayString (SIZE(1..31))read-createcurrent
dtpvcUSProfile
OBJECT-TYPE
The value of this object identifies the row in the atmProfileTable, which applies for this dtpvc in US side.
1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.8DisplayString (SIZE(1..31))read-createcurrent
dtpvcRowStatus
OBJECT-TYPE
This object is used to create a new row or delete an existing row in this table.
1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.9RowStatusread-createcurrent
dtpvcSuperChannel
OBJECT-TYPE
Specified the configured DTPVC is a super channel.
1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.10INTEGER {enable(1), disable(2)}read-createcurrent
dtpvcAcName
OBJECT-TYPE
Access concentrator name for paepvc.
1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.11DisplayStringread-createcurrent
dtpvcServiceName
OBJECT-TYPE
Service name for paepvc.
1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.12DisplayStringread-createcurrent
dtpvcHelloTime
OBJECT-TYPE
The system will close the PVC if there are not any LCP echo messages passed through during the LCP hello time.
1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.13INTEGERread-createcurrent
dtpvcStateTable
OBJECT-TYPE
This table show current DTPVC status.
1.3.6.1.4.1.6321.1.2.3.1.8.14.2not-accessiblecurrent
dtpvcStateEntry
OBJECT-TYPE
An entry in dtpvcStateTable.
1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1not-accessiblecurrent
dtpvcStateVpi
OBJECT-TYPE
VPI of the dtpvc.
1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.1INTEGER (0..255)read-onlycurrent
dtpvcStateVci
OBJECT-TYPE
VCI of the dtpvc.
1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.2INTEGER (1..65535)read-onlycurrent
dtpvcStateSvid
OBJECT-TYPE
Default S-VID of the dtpvc.
1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.3VlanIndexread-onlycurrent
dtpvcStateSPriority
OBJECT-TYPE
S-priority of the dtpvc.
1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.4INTEGER (0..7)read-onlycurrent
dtpvcStateCvid
OBJECT-TYPE
Default C-VID of the dtpvc.
1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.5VlanIndexread-onlycurrent
dtpvcStateCPriority
OBJECT-TYPE
C-priority of the dtpvc.
1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.6INTEGER (0..7)read-onlycurrent
dtpvcStateChannelType
OBJECT-TYPE
The value of this object identifies the channel type at runtime.
1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.8DisplayString (SIZE(1..31))read-onlycurrent
dtpvcStateEncap
OBJECT-TYPE
The value of this object identifies the channel encapsulation at runtime.
1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.9DisplayString (SIZE(1..31))read-onlycurrent
snrMgn
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.8.15
snrMgnTable
OBJECT-TYPE
A table containing the per port SNR Margin configuration.
1.3.6.1.4.1.6321.1.2.3.1.8.15.1not-accessiblecurrent
snrMgnEntry
OBJECT-TYPE
An entry of snrMgnTable.
1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1not-accessiblecurrent
snrMgnMode
OBJECT-TYPE
Configure DSL SNR margin configuration mode of the specified ports. Profile: the SNR margin configuration comes from DSL profile. Line: the SNR margin configuration comes from line configuration.
1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.1INTEGER {profile(0), line(1)}read-writecurrent
snrMgnUcTarget
OBJECT-TYPE
Configured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization.
1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.2INTEGER (0..310)read-writecurrent
snrMgnUcMax
OBJECT-TYPE
Configured Maximum acceptable Signal/Noise Margin. If the Noise Margin is above this the modem should attempt to reduce its power output to optimize its operation.
1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.3INTEGER (0..310)read-writecurrent
snrMgnUcMin
OBJECT-TYPE
Configured Minimum acceptable Signal/Noise Margin. If the noise margin falls below this level, the modem should attempt to increase its power output. If that is not possible the modem will attempt to re-initialize or shut down.
1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.4INTEGER (0..310)read-writecurrent
snrMgnUcDownshift
OBJECT-TYPE
Configured Signal/Noise Margin for rate downshift. If the noise margin falls below this level, the modem should attempt to decrease its transmit rate. In the case that RADSL mode is not present, the value will be `0'.
1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.5INTEGER (0..310)read-writecurrent
snrMgnUcUpshift
OBJECT-TYPE
Configured Signal/Noise Margin for rate upshift. If the noise margin rises above this level, the modem should attempt to increase its transmit rate. In the case that RADSL is not present, the value will be `0'.
1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.6INTEGER (0..310)read-writecurrent
snrMgnUrTarget
OBJECT-TYPE
Configured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization.
1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.7INTEGER (0..310)read-writecurrent
snrMgnUrMax
OBJECT-TYPE
Configured Maximum acceptable Signal/Noise Margin. If the Noise Margin is above this the modem should attempt to reduce its power output to optimize its operation.
1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.8INTEGER (0..310)read-writecurrent
snrMgnUrMin
OBJECT-TYPE
Configured Minimum acceptable Signal/Noise Margin. If the noise margin falls below this level, the modem should attempt to increase its power output. If that is not possible the modem will attempt to re-initialize or shut down.
1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.9INTEGER (0..310)read-writecurrent
snrMgnUrDownshift
OBJECT-TYPE
Configured Signal/Noise Margin for rate downshift. If the noise margin falls below this level, the modem should attempt to decrease its transmit rate. In the case that RADSL mode is not present, the value will be `0'.
1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.10INTEGER (0..310)read-writecurrent
snrMgnUrUpshift
OBJECT-TYPE
Configured Signal/Noise Margin for rate upshift. If the noise margin rises above this level, the modem should attempt to increase its transmit rate. In the case that RADSL is not present, the value will be `0'.
1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.11INTEGER (0..310)read-writecurrent
dslRate
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.8.16
dslRateTable
OBJECT-TYPE
A table containing the per port DSL Rate configuration.
1.3.6.1.4.1.6321.1.2.3.1.8.16.1not-accessiblecurrent
dslRateEntry
OBJECT-TYPE
An entry of dslRateTable.
1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1not-accessiblecurrent
dslRateMode
OBJECT-TYPE
Configure DSL Rate configuration mode of the specified ports. Profile: the DSL Rate configuration comes from DSL profile. Line: the DSL Rate configuration comes from line configuration.
1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.1INTEGER {profile(0), line(1)}read-writecurrent
dslRateLatencyMode
OBJECT-TYPE
The latency mode is fast or interleave
1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.2INTEGER {interleave(1), fast(2)}read-onlycurrent
dslRateXtucMaxInterleaveDelay
OBJECT-TYPE
Configured maximum Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency.
1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.3INTEGER (0..255)read-writecurrent
dslRateXtucMaxTxRate
OBJECT-TYPE
Configured Maximum Transmit rate for `Fast' or `Interleave' channels, in bps.
1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.4Unsigned32read-writecurrent
dslRateXtucMinTxRate
OBJECT-TYPE
Configured Minimum Transmit rate for `Fast' or `Interleave' channels, in bps
1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.5Unsigned32read-writecurrent
dslRateXturMaxInterleaveDelay
OBJECT-TYPE
Configured maximum Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency
1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.6INTEGER (0..255)read-writecurrent
dslRateXturMaxTxRate
OBJECT-TYPE
Configured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization.
1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.7Unsigned32read-writecurrent
dslRateXturMinTxRate
OBJECT-TYPE
Configured Maximum Transmit rate for `Fast' or `Interleave' channels, in bps.
1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.8Unsigned32read-writecurrent
gbond
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.8.51
gbondGroupTable
OBJECT-TYPE
A table containing the G.Bond configuration information for each bonding group of the device.
1.3.6.1.4.1.6321.1.2.3.1.8.51.1not-accessiblecurrent
gbondGroupEntry
OBJECT-TYPE
An entry of gbondTable.
1.3.6.1.4.1.6321.1.2.3.1.8.51.1.1not-accessiblecurrent
gbondGroupName
OBJECT-TYPE
An administratively assigned string, which may be used to identify bonding group.
1.3.6.1.4.1.6321.1.2.3.1.8.51.1.1.1OCTET STRING (SIZE(0..31))read-onlycurrent
gbondGroupPorts
OBJECT-TYPE
The set of ports which are currently assigned to the bonding group of specified group name. Byte 1: Reserved(chassis) Byte 2~3: Reserved(slot) Byte 4: Reserved Byte 5~11:each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc.
1.3.6.1.4.1.6321.1.2.3.1.8.51.1.1.2OCTET STRINGread-createcurrent
gbondGroupUpRate
OBJECT-TYPE
The UP stream rate.
1.3.6.1.4.1.6321.1.2.3.1.8.51.1.1.4Unsigned32read-onlycurrent
gbondGroupDownRate
OBJECT-TYPE
The DOWN stream rate.
1.3.6.1.4.1.6321.1.2.3.1.8.51.1.1.5Unsigned32read-onlycurrent
gbondGroupRowStatus
OBJECT-TYPE
This object indicates the status of this entry.
1.3.6.1.4.1.6321.1.2.3.1.8.51.1.1.6RowStatusread-createcurrent
switch
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.10
dscp
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.10.10
dscpMappingTable
OBJECT-TYPE
The table contains DSCP mapping configuration for the adsl and ethernet ports.
1.3.6.1.4.1.6321.1.2.3.1.10.10.1not-accessiblecurrent
dscpMappingEntry
OBJECT-TYPE
An entry of dscpMappingTable.
1.3.6.1.4.1.6321.1.2.3.1.10.10.1.1not-accessiblecurrent
dscpSrcCodePoint
OBJECT-TYPE
The DSCP source code point used for mapping.
1.3.6.1.4.1.6321.1.2.3.1.10.10.1.1.1INTEGERread-onlycurrent
dscpMapPriority
OBJECT-TYPE
The mapping p bits that will replace the source p bits in the incoming packet.
1.3.6.1.4.1.6321.1.2.3.1.10.10.1.1.3INTEGER (0..7)read-writecurrent
dscpPortTable
OBJECT-TYPE
The table contains DSCP mapping configuration for the adsl and ethernet ports.
1.3.6.1.4.1.6321.1.2.3.1.10.10.2not-accessiblecurrent
dscpPortEntry
OBJECT-TYPE
An entry of dscpPortTable.
1.3.6.1.4.1.6321.1.2.3.1.10.10.2.1not-accessiblecurrent
dscpStatusEnable
OBJECT-TYPE
The DSCP port status.
1.3.6.1.4.1.6321.1.2.3.1.10.10.2.1.1INTEGER {enable(1), disable(2)}read-writecurrent
vlanIsolation
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.10.12
vlanIsolationTable
OBJECT-TYPE
A table contains configuration of isolated VLAN.
1.3.6.1.4.1.6321.1.2.3.1.10.12.1not-accessiblecurrent
vlanIsolationEntry
OBJECT-TYPE
An entry of vlanIsolationTable.
1.3.6.1.4.1.6321.1.2.3.1.10.12.1.1not-accessiblecurrent
vlanIsolationRowStatus
OBJECT-TYPE
Row status of the table used to create/delete an entry.
1.3.6.1.4.1.6321.1.2.3.1.10.12.1.1.1RowStatusread-createcurrent
enetMtu
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.10.13
enetMtuEntry
OBJECT-TYPE
Sets the MTU size for layer 2 frame, size from 1526 to 1532, default value is 1526.
1.3.6.1.4.1.6321.1.2.3.1.10.13.1INTEGERread-writecurrent
dhcp
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.10.51
dhcpRelay82Table
OBJECT-TYPE
A table that contains DHCP Relay configuration.
1.3.6.1.4.1.6321.1.2.3.1.10.51.2not-accessiblecurrent
dhcpRelay82Entry
OBJECT-TYPE
The entry of DHCP Relay table.
1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1not-accessiblecurrent
dhcpRelay82PrimaryServer
OBJECT-TYPE
The IP address of the DHCP Relay primary server.
1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.1IpAddressread-writecurrent
dhcpRelay82SecondaryServer
OBJECT-TYPE
The IP address of the DHCP Relay secondary server.
1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.2IpAddressread-writecurrent
dhcpRelay82ActiveServer
OBJECT-TYPE
The current active DHCP Relay server.
1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.3INTEGER {primary(1), secondary(2), third(3), fourth(4), fifth(5)}read-onlycurrent
dhcpRelay82Enable
OBJECT-TYPE
Enable/disable DHCP relay and Option82 function.
1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.4INTEGER {enable(1), disable(2)}read-createcurrent
dhcpRelay82Info
OBJECT-TYPE
User specific Option82 information.
1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.5DisplayString (SIZE(0..23))read-createcurrent
dhcpRelay82RelayMode
OBJECT-TYPE
DHCP relay mode.
1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.6INTEGER {auto(1), all(2)}read-createcurrent
dhcpRelay82Suboption2Enable
OBJECT-TYPE
Enable/disable Option 82 sub-option 2.
1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.8INTEGER {enable(1), disable(2)}read-createcurrent
dhcpRelay82Suboption2Info
OBJECT-TYPE
User specified information for Option 82 sub-option 2.
1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.9DisplayStringread-createcurrent
dhcpRelay82EntryEnable
OBJECT-TYPE
Enable/disable DHCP Relay
1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.10INTEGER {auto(1), all(2), disable(3)}read-createcurrent
dhcpRelay82EntryOptionMode
OBJECT-TYPE
Option82 format.
1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.11INTEGER {private(1), tr101(2)}read-createcurrent
dhcpRelay82VlanIp
OBJECT-TYPE
The IP address of the DHCP Relay interface for this VLAN.
1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.12IpAddressread-writecurrent
dhcpRelay82VlanMask
OBJECT-TYPE
The network mask of the DHCP Relay interface for this VLAN.
1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.13INTEGERread-writecurrent
dhcpRelay82VlanGateway
OBJECT-TYPE
The gateway of the DHCP Relay interface for this VLAN.
1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.14IpAddressread-writecurrent
dhcpRelay82ThirdServer
OBJECT-TYPE
The IP address of the DHCP Relay third server.
1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.15IpAddressread-writecurrent
dhcpRelay82FourthServer
OBJECT-TYPE
The IP address of the DHCP Relay fourth server.
1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.16IpAddressread-writecurrent
dhcpRelay82FifthServer
OBJECT-TYPE
The IP address of the DHCP Relay fifth server.
1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.17IpAddressread-writecurrent
dhcpRelay82ServerVid
OBJECT-TYPE
The VID of the DHCP Relay server for this VLAN.
1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.18INTEGERread-writecurrent
dhcpRelayTest
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.10.51.8
dhcpRelayTestVid
OBJECT-TYPE
Setting the VID of the test server.
1.3.6.1.4.1.6321.1.2.3.1.10.51.8.1INTEGERread-writecurrent
dhcpRelayTestIp
OBJECT-TYPE
Setting the IP of the test server.
1.3.6.1.4.1.6321.1.2.3.1.10.51.8.2IpAddressread-writecurrent
dhcpRelayTestOps
OBJECT-TYPE
Set the object to 1 to test DHCP server.
1.3.6.1.4.1.6321.1.2.3.1.10.51.8.3INTEGERread-writecurrent
dhcpRelayTestStatus
OBJECT-TYPE
Display testing server status.
1.3.6.1.4.1.6321.1.2.3.1.10.51.8.4DisplayStringread-onlycurrent
dhcpRelayArp
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.10.51.9
dhcpRelayArpShowTable
OBJECT-TYPE
The table displays DHCP ARP.
1.3.6.1.4.1.6321.1.2.3.1.10.51.9.1not-accessiblecurrent
dhcpRelayArpShowEntry
OBJECT-TYPE
An entry of dhcpRelayArpShowTable.
1.3.6.1.4.1.6321.1.2.3.1.10.51.9.1.1not-accessiblecurrent
dhcpRelayArpShowVid
OBJECT-TYPE
Display the VID of the DHCP ARP entry.
1.3.6.1.4.1.6321.1.2.3.1.10.51.9.1.1.1INTEGERread-onlycurrent
dhcpRelayArpShowIp
OBJECT-TYPE
Display the IP of the DHCP ARP entry.
1.3.6.1.4.1.6321.1.2.3.1.10.51.9.1.1.2IpAddressread-onlycurrent
dhcpRelayArpShowMac
OBJECT-TYPE
Display the MAC of the DHCP ARP entry.
1.3.6.1.4.1.6321.1.2.3.1.10.51.9.1.1.3PhysAddressread-onlycurrent
dhcpRelayArpFlushOps
OBJECT-TYPE
Set the object to 1 to start flushing.
1.3.6.1.4.1.6321.1.2.3.1.10.51.9.2INTEGERread-writecurrent
macfilter
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.10.53
macFilterPortTable
OBJECT-TYPE
This table includes the status of mac filtering for each port.
1.3.6.1.4.1.6321.1.2.3.1.10.53.1not-accessiblecurrent
macFilterPortEntry
OBJECT-TYPE
An entry in macFilterPortTable.
1.3.6.1.4.1.6321.1.2.3.1.10.53.1.1not-accessiblecurrent
macFilterPortEnable
OBJECT-TYPE
Enable/disable MAC filtering for the port.
1.3.6.1.4.1.6321.1.2.3.1.10.53.1.1.1INTEGER {enableMacFilter(1), enableMacCount(2), disable(4), enableMacFilterAndMacCount(5)}read-writecurrent
macFilterPortMacCount
OBJECT-TYPE
The total number of MAC addresses allowed for the port.
1.3.6.1.4.1.6321.1.2.3.1.10.53.1.1.2INTEGER (1..128)read-writecurrent
macFilterPortFilterMode
OBJECT-TYPE
The mac filter mode (accept or deny) for the port.
1.3.6.1.4.1.6321.1.2.3.1.10.53.1.1.3INTEGER {accept(1), deny(2)}read-writecurrent
maxNumOfMacFiltersInSystem
OBJECT-TYPE
The max number of mac filters supported in the system.
1.3.6.1.4.1.6321.1.2.3.1.10.53.2INTEGERread-onlycurrent
maxNumOfMacFiltersPerPort
OBJECT-TYPE
The max number of mac filters supported per port.
1.3.6.1.4.1.6321.1.2.3.1.10.53.3INTEGERread-onlycurrent
currNumOfMacFiltersInSystem
OBJECT-TYPE
The current number of mac filters in the system.
1.3.6.1.4.1.6321.1.2.3.1.10.53.4INTEGERread-onlycurrent
macFilterTable
OBJECT-TYPE
A table that contains the mac filter addresses.
1.3.6.1.4.1.6321.1.2.3.1.10.53.5not-accessiblecurrent
macFilterEntry
OBJECT-TYPE
The entry of macFilterTable.
1.3.6.1.4.1.6321.1.2.3.1.10.53.5.1not-accessiblecurrent
macFilterAddr
OBJECT-TYPE
The mac address which can pass through or be rejected from the port.
1.3.6.1.4.1.6321.1.2.3.1.10.53.5.1.1PhysAddressread-onlycurrent
macFilterRowStatus
OBJECT-TYPE
The row status of the entry.
1.3.6.1.4.1.6321.1.2.3.1.10.53.5.1.2RowStatusread-createcurrent
macfilterBatchSet
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.10.53.6
macfilterTarget
OBJECT-TYPE
This managed object is used for identify the target on which the port configuration should be performed. The target is encoded as: Byte 1: 0, Reserved(chassis) Byte 2~3: 0, Reserved(slot) Byte 4: 0, reserved Byte 5~11:each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc.
1.3.6.1.4.1.6321.1.2.3.1.10.53.6.1OCTET STRINGread-writecurrent
macfilterOps
OBJECT-TYPE
The corresponding bit is set to 1 to start the operation. The various bit positions are: BIT 1: enable mac filter BIT 2: enable mac count filter BIT 3: disable mac filter BIT 4: set mac count BIT 5: disable mac count filter.
1.3.6.1.4.1.6321.1.2.3.1.10.53.6.2INTEGERread-writecurrent
macFilterMacCountForBatchSet
OBJECT-TYPE
The total number of MAC addresses allowed for a port.
1.3.6.1.4.1.6321.1.2.3.1.10.53.6.3INTEGER (1..128)read-writecurrent
ouiFilterTableOld
OBJECT-TYPE
A table that contains the OUI filter addresses.
1.3.6.1.4.1.6321.1.2.3.1.10.53.7not-accessiblecurrent
ouiFilterEntryOld
OBJECT-TYPE
The entry of ouiFilterTableOld.
1.3.6.1.4.1.6321.1.2.3.1.10.53.7.1not-accessiblecurrent
ouiFilterAddrOld
OBJECT-TYPE
The first three bytes of the mac address which can pass through or be rejected from the port.
1.3.6.1.4.1.6321.1.2.3.1.10.53.7.1.1OCTET STRINGread-onlycurrent
ouiFilterRowStatusOld
OBJECT-TYPE
The row status of the entry.
1.3.6.1.4.1.6321.1.2.3.1.10.53.7.1.2RowStatusread-createcurrent
maxNumOfOuiFiltersPerPort
OBJECT-TYPE
The max number of OUI filters supported per port.
1.3.6.1.4.1.6321.1.2.3.1.10.53.8INTEGERread-onlycurrent
ouiFilterPortTable
OBJECT-TYPE
This table includes the status of oui filtering for each port.
1.3.6.1.4.1.6321.1.2.3.1.10.53.9not-accessiblecurrent
ouiFilterPortEntry
OBJECT-TYPE
An entry in macFilterPortTable.
1.3.6.1.4.1.6321.1.2.3.1.10.53.9.1not-accessiblecurrent
ouiFilterPortEnable
OBJECT-TYPE
Enable/disable oui filtering for the port.
1.3.6.1.4.1.6321.1.2.3.1.10.53.9.1.1INTEGER {enableOuiFilter(1), disable(2)}read-writecurrent
ouiFilterPortFilterMode
OBJECT-TYPE
The oui filter mode (accept or deny) for the port.
1.3.6.1.4.1.6321.1.2.3.1.10.53.9.1.2INTEGER {accept(1), deny(2)}read-writecurrent
maxNumOfOuiFiltersInSystem
OBJECT-TYPE
The max number of OUI filters supported in system.
1.3.6.1.4.1.6321.1.2.3.1.10.53.10INTEGERread-onlycurrent
maxNumOfOuiFiltersPerVlan
OBJECT-TYPE
The max number of OUI filters supported per vlan.
1.3.6.1.4.1.6321.1.2.3.1.10.53.11INTEGERread-onlycurrent
ouiFilterTable
OBJECT-TYPE
A table that contains the OUI filter addresses.
1.3.6.1.4.1.6321.1.2.3.1.10.53.12not-accessiblecurrent
ouiFilterEntry
OBJECT-TYPE
The entry of ouiFilterTable.
1.3.6.1.4.1.6321.1.2.3.1.10.53.12.1not-accessiblecurrent
ouiFilterAddr
OBJECT-TYPE
The first three bytes of the mac address which can pass through or be rejected from the vlan.
1.3.6.1.4.1.6321.1.2.3.1.10.53.12.1.1OCTET STRINGread-onlycurrent
ouiFilterRowStatus
OBJECT-TYPE
The row status of the entry.
1.3.6.1.4.1.6321.1.2.3.1.10.53.12.1.2RowStatusread-createcurrent
ouiFilterVlanTable
OBJECT-TYPE
This table includes the status of oui filtering for each configured VLAN.
1.3.6.1.4.1.6321.1.2.3.1.10.53.13not-accessiblecurrent
ouiFilterVlanEntry
OBJECT-TYPE
An entry in ouiFilterVlanTable.
1.3.6.1.4.1.6321.1.2.3.1.10.53.13.1not-accessiblecurrent
ouiFilterVlanEnable
OBJECT-TYPE
Enable/disable oui filtering for the VLAN.
1.3.6.1.4.1.6321.1.2.3.1.10.53.13.1.1INTEGER {enableOuiFilter(1), disable(2)}read-writecurrent
ouiFilterVlanFilterMode
OBJECT-TYPE
The oui filter mode (accept or deny) for the VLAN.
1.3.6.1.4.1.6321.1.2.3.1.10.53.13.1.2INTEGER {accept(1), deny(2)}read-writecurrent
dhcpSnoop
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.10.55
dhcpSnoopPortTable
OBJECT-TYPE
This table includes DHCP snooping enable/disable for each port.
1.3.6.1.4.1.6321.1.2.3.1.10.55.1not-accessiblecurrent
dhcpSnoopPortEntry
OBJECT-TYPE
An entry of dhcpSnoopPortTable.
1.3.6.1.4.1.6321.1.2.3.1.10.55.1.1not-accessiblecurrent
dhcpSnoopEnable
OBJECT-TYPE
Enable/disable DHCP snooping for a port.
1.3.6.1.4.1.6321.1.2.3.1.10.55.1.1.1INTEGER {enable(1), disable(2)}read-writecurrent
dhcpSnoopMaxcnt
OBJECT-TYPE
Set the max entries of the DHCP ARP table.
1.3.6.1.4.1.6321.1.2.3.1.10.55.1.1.2INTEGERread-writecurrent
dhcpSnoopSmacverifyEnable
OBJECT-TYPE
Enable/disable DHCP source MAC verify for a port.
1.3.6.1.4.1.6321.1.2.3.1.10.55.1.1.3INTEGER {enable(1), disable(2)}read-writecurrent
dhcpSnoopTarget
OBJECT-TYPE
This managed object is used for identify the target on which the operation should be performed. The target is encoded as: Byte 1: the octet specifies a set of eight chassis, chassis 0 through 7 Byte 2~3: each octet specifies a set of eight slots, with the first octet specifying slots 1 through 8 and the second octet specifying slots 9 through 16. Byte 4: reserved Byte 5~11:each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc.
1.3.6.1.4.1.6321.1.2.3.1.10.55.2OCTET STRINGread-writecurrent
dhcpSnoopOps
OBJECT-TYPE
The corresponding bit is set to 1 to start the operation. The various bit positions are: BIT 1: DHCP snooping table flush.
1.3.6.1.4.1.6321.1.2.3.1.10.55.3INTEGERread-writecurrent
dhcpStaticTable
OBJECT-TYPE
This table defines DHCP static IP addresses.
1.3.6.1.4.1.6321.1.2.3.1.10.55.4not-accessiblecurrent
dhcpStaticEntry
OBJECT-TYPE
An entry of dhcpStaticTable.
1.3.6.1.4.1.6321.1.2.3.1.10.55.4.1not-accessiblecurrent
dhcpStaticIpAddr
OBJECT-TYPE
The IP address which can pass through the port.
1.3.6.1.4.1.6321.1.2.3.1.10.55.4.1.1IpAddressread-onlycurrent
dhcpStaticRowStatus
OBJECT-TYPE
Row status of the table entry.
1.3.6.1.4.1.6321.1.2.3.1.10.55.4.1.2RowStatusread-createcurrent
maxNumOfDhcpStaticIp
OBJECT-TYPE
The maximum number of DHCP static IP addresses which can be created for a port.
1.3.6.1.4.1.6321.1.2.3.1.10.55.5INTEGERread-onlycurrent
dhcpSnoopMaxcntMode
OBJECT-TYPE
When DHCP snooping table is full, new DHCP lease will replace first one in option 0 or will be dropped in option 1.
1.3.6.1.4.1.6321.1.2.3.1.10.55.6INTEGER {replace(1), drop(2)}read-writecurrent
acl
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.10.56
aclSetTable
OBJECT-TYPE
aclsetTable.
1.3.6.1.4.1.6321.1.2.3.1.10.56.1not-accessiblecurrent
aclSetEntry
OBJECT-TYPE
An entry of aclSetTable.
1.3.6.1.4.1.6321.1.2.3.1.10.56.1.1not-accessiblecurrent
aclSetVpi
OBJECT-TYPE
VPI value
1.3.6.1.4.1.6321.1.2.3.1.10.56.1.1.1INTEGERread-onlycurrent
aclSetVci
OBJECT-TYPE
VCI value
1.3.6.1.4.1.6321.1.2.3.1.10.56.1.1.2INTEGERread-onlycurrent
aclSetProfileName
OBJECT-TYPE
ACL Profile name
1.3.6.1.4.1.6321.1.2.3.1.10.56.1.1.3DisplayStringread-onlycurrent
aclSetRowStatus
OBJECT-TYPE
RowStatus of aclSetEntry
1.3.6.1.4.1.6321.1.2.3.1.10.56.1.1.4RowStatusread-writecurrent
aclProfileTable
OBJECT-TYPE
aclProfileTable.
1.3.6.1.4.1.6321.1.2.3.1.10.56.2not-accessiblecurrent
aclProfileEntry
OBJECT-TYPE
An entry of aclProfileTable.
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1not-accessiblecurrent
aclProfileRuleName
OBJECT-TYPE
Profile rule name
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.1DisplayStringread-onlycurrent
aclProfileRuleNumber
OBJECT-TYPE
The managed object is for acl profile rule configuration. etype <etype> vlan <vid> (1), etype <etype> smac <mac> (2), etype <etype> dmac <mac> (3), vlan <vid> smac <mac> (4), vlan <vid> dmac <mac> (5), smac <mac> dmac <mac> (6), vlan <vid> priority <priority> (7), etype <etype> (8), vlan <vid> (9), smac <mac> (10), dmac <mac> (11), priority <priority> (12), protocol <protocol> (13), {srcip <ip>/<mask>{|dstip <ip>/<mask>{|tos <stos> <etos>{|srcport <sport> <eport> {|dstport <sport> <eport>}}}}} (14)
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.2INTEGERread-writecurrent
aclProfileActionNumber
OBJECT-TYPE
Profile action number. Bit 1: rate Bit 2: rvlan Bit 3: rpri Bit 4: deny Bit 1, Bit 2 & Bit 3 can multiple selection.
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.3INTEGERread-writecurrent
aclProfileRuleParamMask
OBJECT-TYPE
Profile rule parameter mask. BIT 1: srcip <ip>/<mask> BIT 2: dstip <ip>/<mask> BIT 3: tos <stos> <etos> BIT 4: srcport <sport> <eport> BIT 5: dstport <sport> <eport>
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.4INTEGERread-writecurrent
aclProfileRuleEtype
OBJECT-TYPE
Profile rule etype
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.5INTEGER (0..65535)read-writecurrent
aclProfileRuleVid
OBJECT-TYPE
Profile rule vid
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.6INTEGER (1..4094)read-writecurrent
aclProfileRuleSmac
OBJECT-TYPE
Profile rule source MAC
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.7PhysAddressread-writecurrent
aclProfileRuleDmac
OBJECT-TYPE
Profile rule destination MAC
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.8PhysAddressread-writecurrent
aclProfileRulePriority
OBJECT-TYPE
Profile rule priority
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.9INTEGER (0..7)read-writecurrent
aclProfileRuleProtocol
OBJECT-TYPE
Profile rule protocol. icmp(1),igmp(2),ip(4),tcp(6), udp(17),gre(47),ospf(89), other ptype
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.10INTEGER (0..255)read-writecurrent
aclProfileRuleSrcIP
OBJECT-TYPE
Profile rule source IP
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.11IpAddressread-writecurrent
aclProfileRuleSrcIPMask
OBJECT-TYPE
The subnet mask of source IP mask
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.12INTEGER (0..32)read-writecurrent
aclProfileRuleDestIP
OBJECT-TYPE
Profile rule source IP
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.13IpAddressread-writecurrent
aclProfileRuleDestIPMask
OBJECT-TYPE
The subnet mask of dest IP mask
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.14INTEGER (0..32)read-writecurrent
aclProfileRuleStartTos
OBJECT-TYPE
Profile rule start type of service
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.15INTEGER (0..255)read-writecurrent
aclProfileRuleEndTos
OBJECT-TYPE
Profile rule end type of service
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.16INTEGER (0..255)read-writecurrent
aclProfileRuleSrcStartPort
OBJECT-TYPE
Profile rule source start port
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.17INTEGER (0..65535)read-writecurrent
aclProfileRuleSrcEndPort
OBJECT-TYPE
Profile rule source end port
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.18INTEGER (0..65535)read-writecurrent
aclProfileRuleDestStartPort
OBJECT-TYPE
Profile rule destination start port
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.19INTEGER (0..65535)read-writecurrent
aclProfileRuleDestEndPort
OBJECT-TYPE
Profile rule destination end port
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.20INTEGER (0..65535)read-writecurrent
aclProfileActionRate
OBJECT-TYPE
Profile action to replace to this rate
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.21INTEGER (1..65535)read-writecurrent
aclProfileActionrvlan
OBJECT-TYPE
Profile action to replace to this vlan
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.22INTEGER (1..4094)read-writecurrent
aclProfileActionrpri
OBJECT-TYPE
Profile action to replace to this priority
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.23INTEGER (0..7)read-writecurrent
aclProfileRowStatus
OBJECT-TYPE
The row status of the entry.
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.24RowStatusread-writecurrent
pppoeAgent
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.10.57
pppoeAgentTable
OBJECT-TYPE
A table that contains PPPoE DHCP Relay configuration.
1.3.6.1.4.1.6321.1.2.3.1.10.57.1not-accessiblecurrent
pppoeAgentEntry
OBJECT-TYPE
An entry of pppoeAgentTable.
1.3.6.1.4.1.6321.1.2.3.1.10.57.1.1not-accessiblecurrent
pppoeAgentEnable
OBJECT-TYPE
Enable/disable DHCP relay and Option82 function.
1.3.6.1.4.1.6321.1.2.3.1.10.57.1.1.1INTEGER {enable(1), disable(2)}read-createcurrent
pppoeAgentInfo
OBJECT-TYPE
User specific Option82 information.
1.3.6.1.4.1.6321.1.2.3.1.10.57.1.1.2DisplayString (SIZE(0..23))read-createcurrent
pppoeAgentRowStatus
OBJECT-TYPE
Row status of the table entry.
1.3.6.1.4.1.6321.1.2.3.1.10.57.1.1.3RowStatusread-createcurrent
pppoeAgentOptionMode
OBJECT-TYPE
Option82 format.
1.3.6.1.4.1.6321.1.2.3.1.10.57.1.1.4INTEGER {private(1), tr101(2)}read-createcurrent
maxNumOfPppoeDhcpRelay82Conf
OBJECT-TYPE
The maximum number of rows that can be created in pppoeAgentTable.
1.3.6.1.4.1.6321.1.2.3.1.10.57.2INTEGERread-onlycurrent
macff
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.10.60
macFfTable
OBJECT-TYPE
A table that contains MAC Force Forwarding configuration.
1.3.6.1.4.1.6321.1.2.3.1.10.60.1not-accessiblecurrent
macFfEntry
OBJECT-TYPE
An entry of macFfTable.
1.3.6.1.4.1.6321.1.2.3.1.10.60.1.1not-accessiblecurrent
macFfIndex
OBJECT-TYPE
Index of the MACFF.
1.3.6.1.4.1.6321.1.2.3.1.10.60.1.1.1INTEGERread-onlycurrent
macFfVid
OBJECT-TYPE
The VLAN-ID refering to this AR/AS.
1.3.6.1.4.1.6321.1.2.3.1.10.60.1.1.2INTEGERread-writecurrent
macFfArIP
OBJECT-TYPE
IP of this AR/AS
1.3.6.1.4.1.6321.1.2.3.1.10.60.1.1.3IpAddressread-writecurrent
macFfSrcIP
OBJECT-TYPE
The source IP address of the MACFF.
1.3.6.1.4.1.6321.1.2.3.1.10.60.1.1.4IpAddressread-writecurrent
macFfSrcMask
OBJECT-TYPE
The subnet mask of source IP mask.
1.3.6.1.4.1.6321.1.2.3.1.10.60.1.1.5INTEGERread-writecurrent
macFfRowStatus
OBJECT-TYPE
The row status of the MacFfEntry entry.
1.3.6.1.4.1.6321.1.2.3.1.10.60.1.1.6RowStatusread-createcurrent
macFfArpFlush
OBJECT-TYPE
Set the object to 1 to flush mac table.
1.3.6.1.4.1.6321.1.2.3.1.10.60.3INTEGERread-writecurrent
maxNumOfMacFfVlanInSystem
OBJECT-TYPE
The max number of macff Vlans supported in the system.
1.3.6.1.4.1.6321.1.2.3.1.10.60.4INTEGERread-onlycurrent
macFfVlanTable
OBJECT-TYPE
A table that contains MAC Force Forwarding Vlan configuration.
1.3.6.1.4.1.6321.1.2.3.1.10.60.5not-accessiblecurrent
macFfVlanEntry
OBJECT-TYPE
An entry of macFfVlanTable.
1.3.6.1.4.1.6321.1.2.3.1.10.60.5.1not-accessiblecurrent
macFfVlanRowstatus
OBJECT-TYPE
Row status of the table used to create/delete an entry.
1.3.6.1.4.1.6321.1.2.3.1.10.60.5.1.1RowStatusread-createcurrent
macFfVlanUnknownUnicast
OBJECT-TYPE
Setting downstream unknown uni-cast packet on macff vlan to flooding or dropping.
1.3.6.1.4.1.6321.1.2.3.1.10.60.5.1.2INTEGER {flood(1), drop(2)}read-createcurrent
macFfStaticIPTable
OBJECT-TYPE
1.3.6.1.4.1.6321.1.2.3.1.10.60.6not-accessiblecurrent
macFfStaticIPEntry
OBJECT-TYPE
An entry of macFfTable.
1.3.6.1.4.1.6321.1.2.3.1.10.60.6.1not-accessiblecurrent
macFfStaticIPPort
OBJECT-TYPE
The port number, 1 ~ 48.
1.3.6.1.4.1.6321.1.2.3.1.10.60.6.1.1INTEGERread-onlycurrent
macFfStaticIPVid
OBJECT-TYPE
VLAN ID of the IP range, 1 ~ 4094, the vid should be enable the MACFF function first.
1.3.6.1.4.1.6321.1.2.3.1.10.60.6.1.2INTEGERread-onlycurrent
macFfstaticIP
OBJECT-TYPE
The specified IP range.
1.3.6.1.4.1.6321.1.2.3.1.10.60.6.1.3IpAddressread-onlycurrent
macFfStaticIPMask
OBJECT-TYPE
Mask_bits is 24 .. 32.
1.3.6.1.4.1.6321.1.2.3.1.10.60.6.1.4INTEGERread-onlycurrent
macFfStaticIPRowStatus
OBJECT-TYPE
The row status used to configure the table entry.
1.3.6.1.4.1.6321.1.2.3.1.10.60.6.1.5RowStatusread-createcurrent
sys
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.11
accessCtrl
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.11.5
securedClientTable
OBJECT-TYPE
A table that contains information about secured clients.
1.3.6.1.4.1.6321.1.2.3.1.11.5.2not-accessiblecurrent
securedClientEntry
OBJECT-TYPE
A list of secured client entry.
1.3.6.1.4.1.6321.1.2.3.1.11.5.2.1not-accessiblecurrent
securedClientIndex
OBJECT-TYPE
The index of the entry.
1.3.6.1.4.1.6321.1.2.3.1.11.5.2.1.1INTEGERread-onlycurrent
securedClientStartIp
OBJECT-TYPE
The starting IP address of the secured client set.
1.3.6.1.4.1.6321.1.2.3.1.11.5.2.1.2IpAddressread-writecurrent
securedClientEndIp
OBJECT-TYPE
The ending IP address of the secured client set.
1.3.6.1.4.1.6321.1.2.3.1.11.5.2.1.3IpAddressread-writecurrent
securedClientService
OBJECT-TYPE
Each bit corresponds to a service. The bit is set to 1 if the service is enabled, and set to 0 if the service is disabled. The various bit positions are: BIT 1: telnet BIT 2: ftp BIT 3: web BIT 4: icmp BIT 5: not support BIT 6: snmp.
1.3.6.1.4.1.6321.1.2.3.1.11.5.2.1.4INTEGERread-writecurrent
securedClientEnable
OBJECT-TYPE
Enable/disable the entry.
1.3.6.1.4.1.6321.1.2.3.1.11.5.2.1.5INTEGER {enable(1), disable(2)}read-writecurrent
extAlarm
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.11.8
extAlarmTable
OBJECT-TYPE
A table that contains external alarm information.
1.3.6.1.4.1.6321.1.2.3.1.11.8.1not-accessiblecurrent
extAlarmEntry
OBJECT-TYPE
The entry of external alarm table.
1.3.6.1.4.1.6321.1.2.3.1.11.8.1.1not-accessiblecurrent
extAlarmIndex
OBJECT-TYPE
The index of the entry.
1.3.6.1.4.1.6321.1.2.3.1.11.8.1.1.1INTEGERread-onlycurrent
extAlarmname
OBJECT-TYPE
The external alarm name.
1.3.6.1.4.1.6321.1.2.3.1.11.8.1.1.2DisplayString (SIZE(1..31))read-writecurrent
extAlarmstatus
OBJECT-TYPE
Dispaly 'Normal' or 'Alarm' string
1.3.6.1.4.1.6321.1.2.3.1.11.8.1.1.3DisplayString (SIZE(1..31))read-onlycurrent
extAlarmTriggeredMode
OBJECT-TYPE
The external alarm triggered mode.
1.3.6.1.4.1.6321.1.2.3.1.11.8.1.1.4INTEGER {closeAlarm(1), openAlarm(2)}read-writecurrent
user
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.11.9
userAuthMode
OBJECT-TYPE
User authentication procsssing mode.
1.3.6.1.4.1.6321.1.2.3.1.11.9.1INTEGER {local(1), radius(2), localThenRadius(3)}read-writecurrent
userAuthServerIp
OBJECT-TYPE
The IP address of the authentication server.
1.3.6.1.4.1.6321.1.2.3.1.11.9.2IpAddressread-writecurrent
userAuthServerPort
OBJECT-TYPE
The port of the authentication server.
1.3.6.1.4.1.6321.1.2.3.1.11.9.3INTEGERread-writecurrent
userAuthServerSecret
OBJECT-TYPE
The secret between the authentication server and the NE for authentication process.
1.3.6.1.4.1.6321.1.2.3.1.11.9.4OCTET STRINGread-writecurrent
userTable
OBJECT-TYPE
A table that contains user information.
1.3.6.1.4.1.6321.1.2.3.1.11.9.5not-accessiblecurrent
userEntry
OBJECT-TYPE
An entry of userTable.
1.3.6.1.4.1.6321.1.2.3.1.11.9.5.1not-accessiblecurrent
userName
OBJECT-TYPE
The user name.
1.3.6.1.4.1.6321.1.2.3.1.11.9.5.1.1DisplayStringread-onlycurrent
userPassword
OBJECT-TYPE
The user password.
1.3.6.1.4.1.6321.1.2.3.1.11.9.5.1.2DisplayStringread-createcurrent
userPriviledge
OBJECT-TYPE
The user priviledge to decide what operation the user can and cannot do.
1.3.6.1.4.1.6321.1.2.3.1.11.9.5.1.3INTEGER {high(1), middle(2), low(3)}read-createcurrent
userRowStatus
OBJECT-TYPE
The row status used to create or delete a user.
1.3.6.1.4.1.6321.1.2.3.1.11.9.5.1.4RowStatusread-createcurrent
userAuthDefaultPriviledge
OBJECT-TYPE
The user default priviledge to be assigned when radius authentication succeds but no user priviledge information(radius service-type) is provided.
1.3.6.1.4.1.6321.1.2.3.1.11.9.6INTEGER {high(1), middle(2), low(3), deny(4)}read-writecurrent
usbCastCtrl
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.11.10
usBcastCtrlEnable
OBJECT-TYPE
Enable/disable upstream broadcast control.
1.3.6.1.4.1.6321.1.2.3.1.11.10.1INTEGER {enable(1), disable(2)}read-writecurrent
usBcastCtrlRate
OBJECT-TYPE
32~49984 in step of 32kbps
1.3.6.1.4.1.6321.1.2.3.1.11.10.2INTEGERread-writecurrent
dsbCastCtrl
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.11.11
dsBcastCtrlEnable
OBJECT-TYPE
Enable/disable downstream broadcast control.
1.3.6.1.4.1.6321.1.2.3.1.11.11.1INTEGER {enable(1), disable(2)}read-writecurrent
dsBcastCtrlRate
OBJECT-TYPE
32~1000000 in step of 32 kbps
1.3.6.1.4.1.6321.1.2.3.1.11.11.2INTEGERread-writecurrent
stdioTimeout
OBJECT-TYPE
Set the CLI/TELNET/WEB Session timeout, 0, or 1~300 minutes, 0 => disable.
1.3.6.1.4.1.6321.1.2.3.1.11.12INTEGER (0..300)read-writecurrent
isConfigChanged
OBJECT-TYPE
If system configuration has been changed.
1.3.6.1.4.1.6321.1.2.3.1.11.13INTEGER {yes(1), no(2)}read-onlycurrent
fwUpgrade
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.11.14
fwUpgradeVersion
OBJECT-TYPE
Configure the target firmware version that will be upgraded.
1.3.6.1.4.1.6321.1.2.3.1.11.14.1OCTET STRINGread-writecurrent
fwUpgradeCheck
OBJECT-TYPE
Enable/disable firmware upgrade version checking feature.
1.3.6.1.4.1.6321.1.2.3.1.11.14.2INTEGER {enable(1), disable(2)}read-writecurrent
fwUpgradeStatus
OBJECT-TYPE
Display current firmware upgrade status.
1.3.6.1.4.1.6321.1.2.3.1.11.14.3DisplayStringread-onlycurrent
delayedReboot
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.11.15
delayedRebootTimer
OBJECT-TYPE
5~1800 secs, 0: reboot immediately.
1.3.6.1.4.1.6321.1.2.3.1.11.15.1INTEGERread-writecurrent
delayedRebootRemainingTime
OBJECT-TYPE
Display the remaining time of scheduled reboot.
1.3.6.1.4.1.6321.1.2.3.1.11.15.2INTEGERread-onlycurrent
delayedRebootCancel
OBJECT-TYPE
cancel the scheduled reboot.
1.3.6.1.4.1.6321.1.2.3.1.11.15.3INTEGER {cancel(1)}read-writecurrent
trap
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.12
statistics
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.13
igmpQueryCntTotal
OBJECT-TYPE
The total number of IGMP query messages received.
1.3.6.1.4.1.6321.1.2.3.1.13.1Counter32read-onlycurrent
igmpReportCntTotal
OBJECT-TYPE
The total number of IGMP report messages received.
1.3.6.1.4.1.6321.1.2.3.1.13.2Counter32read-onlycurrent
igmpLeaveCntTotal
OBJECT-TYPE
The total number of IGMP leave messages received.
1.3.6.1.4.1.6321.1.2.3.1.13.3Counter32read-onlycurrent
igmpNumOfActiveGroups
OBJECT-TYPE
The total number of IGMP learned groups.
1.3.6.1.4.1.6321.1.2.3.1.13.4INTEGERread-onlycurrent
igmpGroupTable
OBJECT-TYPE
This table includes igmp group information.
1.3.6.1.4.1.6321.1.2.3.1.13.5not-accessiblecurrent
igmpGroupEntry
OBJECT-TYPE
An entry in igmpGroupTable.
1.3.6.1.4.1.6321.1.2.3.1.13.5.1not-accessiblecurrent
igmpGroupIp
OBJECT-TYPE
igmp group IP
1.3.6.1.4.1.6321.1.2.3.1.13.5.1.1IpAddressread-onlycurrent
igmpGroupvid
OBJECT-TYPE
vlan id
1.3.6.1.4.1.6321.1.2.3.1.13.5.1.2INTEGERread-onlycurrent
igmpGroupnumberOfMembers
OBJECT-TYPE
number Of Members
1.3.6.1.4.1.6321.1.2.3.1.13.5.1.3INTEGERread-onlycurrent
igmpGroupMemberPorts
OBJECT-TYPE
Group Member Ports
1.3.6.1.4.1.6321.1.2.3.1.13.5.1.4PortListread-onlycurrent
igmpGroupPortTable
OBJECT-TYPE
This table includes igmp Group port information.
1.3.6.1.4.1.6321.1.2.3.1.13.6not-accessiblecurrent
igmpGroupPortEntry
OBJECT-TYPE
An entry in igmpGroupPortTable.
1.3.6.1.4.1.6321.1.2.3.1.13.6.1not-accessiblecurrent
igmpGroupPortIp
OBJECT-TYPE
Igmp Group IP
1.3.6.1.4.1.6321.1.2.3.1.13.6.1.1IpAddressread-onlycurrent
igmpGroupPortvid
OBJECT-TYPE
Igmp Group vid
1.3.6.1.4.1.6321.1.2.3.1.13.6.1.2INTEGERread-onlycurrent
igmpGroupV2Table
OBJECT-TYPE
A table that displays IGMP learned group member information.
1.3.6.1.4.1.6321.1.2.3.1.13.7not-accessiblecurrent
igmpGroupV2Entry
OBJECT-TYPE
An entry of igmpGroupV2Table.
1.3.6.1.4.1.6321.1.2.3.1.13.7.1not-accessiblecurrent
igmpGroupV2Vid
OBJECT-TYPE
The IGMP group VLAN ID.
1.3.6.1.4.1.6321.1.2.3.1.13.7.1.1VlanIndexread-onlycurrent
igmpGroupV2Ip
OBJECT-TYPE
The multicast IP address.
1.3.6.1.4.1.6321.1.2.3.1.13.7.1.2IpAddressread-onlycurrent
igmpGroupV2NumOfMembers
OBJECT-TYPE
The number of member ports in the group.
1.3.6.1.4.1.6321.1.2.3.1.13.7.1.3INTEGERread-onlycurrent
igmpGroupV2MemberPorts
OBJECT-TYPE
The member port list of the group.
1.3.6.1.4.1.6321.1.2.3.1.13.7.1.4PortListread-onlycurrent
igmpGroupPortV2Table
OBJECT-TYPE
A table that displays IGMP joined groups in this port.
1.3.6.1.4.1.6321.1.2.3.1.13.8not-accessiblecurrent
igmpGroupPortV2Entry
OBJECT-TYPE
An entry of igmpGroupPortV2Table.
1.3.6.1.4.1.6321.1.2.3.1.13.8.1not-accessiblecurrent
igmpGroupPortV2Vid
OBJECT-TYPE
The IGMP group VLAN ID.
1.3.6.1.4.1.6321.1.2.3.1.13.8.1.1VlanIndexread-onlycurrent
igmpGroupPortV2Ip
OBJECT-TYPE
The multicast IP address.
1.3.6.1.4.1.6321.1.2.3.1.13.8.1.2IpAddressread-onlycurrent
igmpGroupPortV2SourceIp
OBJECT-TYPE
The source IP address that joins the IGMP group.
1.3.6.1.4.1.6321.1.2.3.1.13.8.1.3IpAddressread-onlycurrent
igmpPortCtrlPduTable
OBJECT-TYPE
A table that displays IGMP related counter values in this port.
1.3.6.1.4.1.6321.1.2.3.1.13.9not-accessiblecurrent
igmpPortCtrlPduEntry
OBJECT-TYPE
An entry of igmpPortCtrlPduTable.
1.3.6.1.4.1.6321.1.2.3.1.13.9.1not-accessiblecurrent
igmpPortCtrlPduQueryCnt
OBJECT-TYPE
The total number of IGMP query messages received in this port.
1.3.6.1.4.1.6321.1.2.3.1.13.9.1.1Counter32read-onlycurrent
igmpPortCtrlPduReportCnt
OBJECT-TYPE
The total number of IGMP report messages received in this port.
1.3.6.1.4.1.6321.1.2.3.1.13.9.1.2Counter32read-onlycurrent
igmpPortCtrlPduLeaveCnt
OBJECT-TYPE
The total number of IGMP leave messages received in this port.
1.3.6.1.4.1.6321.1.2.3.1.13.9.1.3Counter32read-onlycurrent
igmpPortNumOfActiveGroups
OBJECT-TYPE
The total number of active IGMP groups in this port.
1.3.6.1.4.1.6321.1.2.3.1.13.9.1.4INTEGERread-onlycurrent
igmpPortCtrlAuditLeaveCnt
OBJECT-TYPE
The total number of groups left by audit query.
1.3.6.1.4.1.6321.1.2.3.1.13.9.1.5Counter32read-onlycurrent
dhcpStats
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.13.11
dhcpSnoopIpTable
OBJECT-TYPE
This table shows the IP addresses and netmasks offered by the DHCP server.
1.3.6.1.4.1.6321.1.2.3.1.13.11.1not-accessiblecurrent
dhcpSnoopIpEntry
OBJECT-TYPE
An entry of dhcpSnoopIpTable.
1.3.6.1.4.1.6321.1.2.3.1.13.11.1.1not-accessiblecurrent
dhcpSnoopIp
OBJECT-TYPE
The snooped IP address.
1.3.6.1.4.1.6321.1.2.3.1.13.11.1.1.1IpAddressread-onlycurrent
dhcpSnoopMac
OBJECT-TYPE
The snooped MAC address.
1.3.6.1.4.1.6321.1.2.3.1.13.11.1.1.2PhysAddressread-onlycurrent
dhcpSnoopVid
OBJECT-TYPE
The snooped VLAN ID.
1.3.6.1.4.1.6321.1.2.3.1.13.11.1.1.3VlanIndexread-onlycurrent
dhcpSnoopMask
OBJECT-TYPE
The snooped IP mask
1.3.6.1.4.1.6321.1.2.3.1.13.11.1.1.4INTEGERread-onlycurrent
dhcpSnoopGateway
OBJECT-TYPE
The snooped Gateway.
1.3.6.1.4.1.6321.1.2.3.1.13.11.1.1.5IpAddressread-onlycurrent
dhcpSnoopRouteMap
OBJECT-TYPE
The refrence bit map of the dhcp route
1.3.6.1.4.1.6321.1.2.3.1.13.11.1.1.6OCTET STRINGread-onlycurrent
dhcpSnoopCounterTable
OBJECT-TYPE
This table shows the DHCP statistics.
1.3.6.1.4.1.6321.1.2.3.1.13.11.2not-accessiblecurrent
dhcpSnoopCounterEntry
OBJECT-TYPE
An entry of dhcpSnoopCounterTable.
1.3.6.1.4.1.6321.1.2.3.1.13.11.2.1not-accessiblecurrent
dhcpDiscovery
OBJECT-TYPE
The total number of received DHCP server discovery packets.
1.3.6.1.4.1.6321.1.2.3.1.13.11.2.1.1Counter64read-onlycurrent
dhcpOffer
OBJECT-TYPE
The total number of received DHCP server offer packets.
1.3.6.1.4.1.6321.1.2.3.1.13.11.2.1.2Counter64read-onlycurrent
dhcpRequest
OBJECT-TYPE
The total number of received DHCP IP request packets.
1.3.6.1.4.1.6321.1.2.3.1.13.11.2.1.3Counter64read-onlycurrent
dhcpAck
OBJECT-TYPE
The total number of received DHCP IP acknowledge packets.
1.3.6.1.4.1.6321.1.2.3.1.13.11.2.1.4Counter64read-onlycurrent
dhcpAckBySnoopFull
OBJECT-TYPE
The total number of received DHCP IP acknowledge packets that replace the oldest snooping entry in snooping table due to table full.
1.3.6.1.4.1.6321.1.2.3.1.13.11.2.1.5Counter64read-onlycurrent
dhcpRouteTable
OBJECT-TYPE
A table that contains dhcp route information.
1.3.6.1.4.1.6321.1.2.3.1.13.11.3not-accessiblecurrent
dhcpRouteEntry
OBJECT-TYPE
An entry of dhcpRouteTable.
1.3.6.1.4.1.6321.1.2.3.1.13.11.3.1not-accessiblecurrent
dhcpRouteIndex
OBJECT-TYPE
1.3.6.1.4.1.6321.1.2.3.1.13.11.3.1.1INTEGER (1..24)read-onlycurrent
dhcpRouteVid
OBJECT-TYPE
The VLAN-ID refering to this dhcp route.
1.3.6.1.4.1.6321.1.2.3.1.13.11.3.1.2VlanIndexread-onlycurrent
dhcpRouteIP
OBJECT-TYPE
IP of this dhcp route
1.3.6.1.4.1.6321.1.2.3.1.13.11.3.1.3IpAddressread-onlycurrent
dhcpRouteMask
OBJECT-TYPE
The subnet mask of source IP mask.
1.3.6.1.4.1.6321.1.2.3.1.13.11.3.1.4INTEGERread-onlycurrent
dhcpRouteGwIP
OBJECT-TYPE
The gateway IP address.
1.3.6.1.4.1.6321.1.2.3.1.13.11.3.1.5IpAddressread-onlycurrent
paepvcStats
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.13.12
paepvcSessionTable
OBJECT-TYPE
This table shows the paepvc session statistics.
1.3.6.1.4.1.6321.1.2.3.1.13.12.1not-accessiblecurrent
paepvcSessionEntry
OBJECT-TYPE
An entry of paepvcSessionTable.
1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1not-accessiblecurrent
paepvcSessionVpi
OBJECT-TYPE
The PAEPVC VPI.
1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1.1INTEGERread-onlycurrent
paepvcSessionVci
OBJECT-TYPE
The PAEPVC VCI.
1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1.2INTEGERread-onlycurrent
paepvcSessionState
OBJECT-TYPE
The PAEPVC status.
1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1.3INTEGER {down(1), pppoe(2), ppp(3), up(4)}read-onlycurrent
paepvcSessionId
OBJECT-TYPE
The PAEPVC session ID.
1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1.4INTEGERread-onlycurrent
paepvcSessionUptime
OBJECT-TYPE
The PAEPVC session uptime.
1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1.5Unsigned32read-onlycurrent
paepvcSessionacname
OBJECT-TYPE
Access concentrator name.
1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1.6DisplayStringread-onlycurrent
paepvcSessionsrvcname
OBJECT-TYPE
Service name.
1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1.7DisplayStringread-onlycurrent
paepvcCountTable
OBJECT-TYPE
This table shows the paepvc counters.
1.3.6.1.4.1.6321.1.2.3.1.13.12.2not-accessiblecurrent
paepvcCountEntry
OBJECT-TYPE
An entry of paepvcCountTable.
1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1not-accessiblecurrent
paepvcCountVpi
OBJECT-TYPE
The PAEPVC VPI.
1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.1INTEGERread-onlycurrent
paepvcCountVci
OBJECT-TYPE
The PAEPVC VCI.
1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.2INTEGERread-onlycurrent
paepvcCountPppLcpCfgReqRx
OBJECT-TYPE
The number of ppp lcp config-request received.
1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.3Unsigned32read-onlycurrent
paepvcCountPppLcpEchoReqRx
OBJECT-TYPE
The number of ppp lcp echo-request received.
1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.4Unsigned32read-onlycurrent
paepvcCountPppLcpEchoReplyRx
OBJECT-TYPE
The number of ppp lcp echo-reply received.
1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.5Unsigned32read-onlycurrent
paepvcCountPadiTx
OBJECT-TYPE
The number of pppoe padi transfered
1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.6Unsigned32read-onlycurrent
paepvcCountPadoRx
OBJECT-TYPE
The number of pppoe pado received
1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.7Unsigned32read-onlycurrent
paepvcCountPadrTx
OBJECT-TYPE
The number of pppoe padr transfered
1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.8Unsigned32read-onlycurrent
paepvcCountPadsRx
OBJECT-TYPE
The number of pppoe pads received
1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.9Unsigned32read-onlycurrent
paepvcCountPadtTx
OBJECT-TYPE
The number of pppoe padt transfered
1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.10Unsigned32read-onlycurrent
paepvcCountPadtRx
OBJECT-TYPE
The number of pppoe padt received
1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.11Unsigned32read-onlycurrent
paepvcCountSrvcnameErrRx
OBJECT-TYPE
The number of pppoe service name error received
1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.12Unsigned32read-onlycurrent
paepvcCountAcSystemErrRx
OBJECT-TYPE
The number of pppoe access concentrator name error received
1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.13Unsigned32read-onlycurrent
paepvcCountGenericErrTx
OBJECT-TYPE
The number of pppoe generic error transfered
1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.14Unsigned32read-onlycurrent
paepvcCountGenericErrRx
OBJECT-TYPE
The number of pppoe generic error received
1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.15Unsigned32read-onlycurrent
macStats
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.13.13
macDisplayTarget
OBJECT-TYPE
This managed object is a filter used for identify the target from which the MAC addresses are learned in macTable. The target could be: 99: all ports in the system 98: all subscriber ports 97: all Ethernet ports IfIndex is used for identifying subscriber ports and Ethernet Ports(e.g. 1 ~ 50).
1.3.6.1.4.1.6321.1.2.3.1.13.13.1INTEGERread-writecurrent
macTable
OBJECT-TYPE
A table that contains information about unicast entries for which the bridge has forwarding and/or filtering information. This information is used by the transparent bridging function in determining how to propagate a received frame.
1.3.6.1.4.1.6321.1.2.3.1.13.13.2not-accessiblecurrent
macEntry
OBJECT-TYPE
An entry of macTable.
1.3.6.1.4.1.6321.1.2.3.1.13.13.2.1not-accessiblecurrent
macAddress
OBJECT-TYPE
A unicast MAC address for which the bridge has forwarding and/or filtering information.
1.3.6.1.4.1.6321.1.2.3.1.13.13.2.1.1MacAddressread-onlycurrent
macPort
OBJECT-TYPE
The port from which the mac address has been learned.
1.3.6.1.4.1.6321.1.2.3.1.13.13.2.1.2INTEGERread-onlycurrent
macStatus
OBJECT-TYPE
The status of this entry.
1.3.6.1.4.1.6321.1.2.3.1.13.13.2.1.3INTEGER {other(1), invalid(2), learned(3), self(4), mgmt(5)}read-onlycurrent
ipbpvcStats
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.13.14
arpproxyTable
OBJECT-TYPE
Display ARP table. This table is supported by R3.00 and later versions.
1.3.6.1.4.1.6321.1.2.3.1.13.14.1not-accessiblecurrent
arpproxyEntry
OBJECT-TYPE
An entry of arpproxyTable.
1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1not-accessiblecurrent
arpproxyIp
OBJECT-TYPE
1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.1IpAddressread-onlycurrent
arpproxyMac
OBJECT-TYPE
1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.2MacAddressread-onlycurrent
arpproxyIfIndex
OBJECT-TYPE
1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.3INTEGERread-onlycurrent
arpproxyVpi
OBJECT-TYPE
1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.4INTEGERread-onlycurrent
arpproxyVci
OBJECT-TYPE
1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.5INTEGERread-onlycurrent
arpproxyInterfaceIp
OBJECT-TYPE
1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.6IpAddressread-onlycurrent
arpproxyInterfaceMask
OBJECT-TYPE
1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.7INTEGERread-onlycurrent
arpproxyInterfaceVid
OBJECT-TYPE
1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.8VlanIndexread-onlycurrent
arpproxyDhcpIp
OBJECT-TYPE
1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.9INTEGER {true(1), false(2)}read-onlycurrent
arpproxyType
OBJECT-TYPE
1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.10INTEGER {upstream(1), downstream(2)}read-onlycurrent
ipbpvcIfDynamicTable
OBJECT-TYPE
Display runtime interfaces. This table is supported by R3.00 and later versions.
1.3.6.1.4.1.6321.1.2.3.1.13.14.2not-accessiblecurrent
ipbpvcIfDynamicEntry
OBJECT-TYPE
An entry of ipbpvcIfDynamicTable.
1.3.6.1.4.1.6321.1.2.3.1.13.14.2.1not-accessiblecurrent
ipbpvcIfDynamicIp
OBJECT-TYPE
1.3.6.1.4.1.6321.1.2.3.1.13.14.2.1.1IpAddressread-onlycurrent
ipbpvcIfDynamicMask
OBJECT-TYPE
1.3.6.1.4.1.6321.1.2.3.1.13.14.2.1.2INTEGERread-onlycurrent
ipbpvcIfDynamicIfIndex
OBJECT-TYPE
1.3.6.1.4.1.6321.1.2.3.1.13.14.2.1.3INTEGERread-onlycurrent
ipbpvcIfDynamicVpi
OBJECT-TYPE
1.3.6.1.4.1.6321.1.2.3.1.13.14.2.1.4INTEGERread-onlycurrent
ipbpvcIfDynamicVci
OBJECT-TYPE
1.3.6.1.4.1.6321.1.2.3.1.13.14.2.1.5INTEGERread-onlycurrent
ipbpvcRouteDynamicTable
OBJECT-TYPE
Display runtime routing table. This table is supported by R3.00 and later versions.
1.3.6.1.4.1.6321.1.2.3.1.13.14.3not-accessiblecurrent
ipbpvcRouteDynamicEntry
OBJECT-TYPE
An entry of ipbpvcRouteDynamicTable.
1.3.6.1.4.1.6321.1.2.3.1.13.14.3.1not-accessiblecurrent
ipbpvcRouteDynamicType
OBJECT-TYPE
1.3.6.1.4.1.6321.1.2.3.1.13.14.3.1.1INTEGER {upstream(1), downstream(2)}read-onlycurrent
ipbpvcRouteDynamicIp
OBJECT-TYPE
1.3.6.1.4.1.6321.1.2.3.1.13.14.3.1.2IpAddressread-onlycurrent
ipbpvcRouteDynamicMask
OBJECT-TYPE
1.3.6.1.4.1.6321.1.2.3.1.13.14.3.1.3INTEGERread-onlycurrent
ipbpvcRouteDynamicNextHop
OBJECT-TYPE
1.3.6.1.4.1.6321.1.2.3.1.13.14.3.1.4IpAddressread-onlycurrent
ipbpvcRouteDynamicMetric
OBJECT-TYPE
1.3.6.1.4.1.6321.1.2.3.1.13.14.3.1.5INTEGERread-onlycurrent
ipbpvcRouteDynamicPriority
OBJECT-TYPE
1.3.6.1.4.1.6321.1.2.3.1.13.14.3.1.6INTEGERread-onlycurrent
macffStats
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.13.16
macFfStatsTable
OBJECT-TYPE
A table that contains MAC Force Forwarding static configuration and dynamic information.
1.3.6.1.4.1.6321.1.2.3.1.13.16.1not-accessiblecurrent
macFfStatsEntry
OBJECT-TYPE
An entry of macFfStatsTable.
1.3.6.1.4.1.6321.1.2.3.1.13.16.1.1not-accessiblecurrent
macFfStatsIndex
OBJECT-TYPE
Index of the MACFF.
1.3.6.1.4.1.6321.1.2.3.1.13.16.1.1.1INTEGERread-onlycurrent
macFfStatsVid
OBJECT-TYPE
The VLAN-ID refering to this AR/AS.
1.3.6.1.4.1.6321.1.2.3.1.13.16.1.1.2VlanIndexread-onlycurrent
macFfStatsArIP
OBJECT-TYPE
IP of this AR/AS
1.3.6.1.4.1.6321.1.2.3.1.13.16.1.1.3IpAddressread-onlycurrent
macFfStatsSrcIP
OBJECT-TYPE
The source IP address of the MACFF.
1.3.6.1.4.1.6321.1.2.3.1.13.16.1.1.4IpAddressread-onlycurrent
macFfStatsSrcMask
OBJECT-TYPE
The subnet mask of source IP mask.
1.3.6.1.4.1.6321.1.2.3.1.13.16.1.1.5INTEGERread-onlycurrent
macFfArpTable
OBJECT-TYPE
A table that contains MAC Force Forwarding ARP information.
1.3.6.1.4.1.6321.1.2.3.1.13.16.2not-accessiblecurrent
macFfArpEntry
OBJECT-TYPE
An entry of macFfArpTable.
1.3.6.1.4.1.6321.1.2.3.1.13.16.2.1not-accessiblecurrent
macFfArpVid
OBJECT-TYPE
The VLAN-ID refering to this AR/AS.
1.3.6.1.4.1.6321.1.2.3.1.13.16.2.1.1VlanIndexread-onlycurrent
macFfArpIP
OBJECT-TYPE
IP of this AR/AS.
1.3.6.1.4.1.6321.1.2.3.1.13.16.2.1.2IpAddressread-onlycurrent
macFfArpPort
OBJECT-TYPE
Port of this AR/AS.
1.3.6.1.4.1.6321.1.2.3.1.13.16.2.1.3INTEGERread-onlycurrent
macFfArpMac
OBJECT-TYPE
MAC address of the AR or AS.
1.3.6.1.4.1.6321.1.2.3.1.13.16.2.1.4PhysAddressread-onlycurrent
macFfArpCounterTable
OBJECT-TYPE
A table that contains MAC Force Forwarding ARP counter information.
1.3.6.1.4.1.6321.1.2.3.1.13.16.3not-accessiblecurrent
macFfArpCounterEntry
OBJECT-TYPE
An entry of macFfArpCounterTable.
1.3.6.1.4.1.6321.1.2.3.1.13.16.3.1not-accessiblecurrent
macFfArpCounterRequestTX
OBJECT-TYPE
ARP Request TX counter.
1.3.6.1.4.1.6321.1.2.3.1.13.16.3.1.1Counter32read-onlycurrent
macFfArpCounterRequestRX
OBJECT-TYPE
ARP Request RX counter.
1.3.6.1.4.1.6321.1.2.3.1.13.16.3.1.2Counter32read-onlycurrent
macFfArpCounterRequestRXDrop
OBJECT-TYPE
ARP Request RX drop counter.
1.3.6.1.4.1.6321.1.2.3.1.13.16.3.1.3Counter32read-onlycurrent
macFfArpCounterReplyTX
OBJECT-TYPE
ARP Reply TX counter.
1.3.6.1.4.1.6321.1.2.3.1.13.16.3.1.4Counter32read-onlycurrent
macFfArpCounterReplyRX
OBJECT-TYPE
ARP Reply RX counter.
1.3.6.1.4.1.6321.1.2.3.1.13.16.3.1.5Counter32read-onlycurrent
macFfArpCounterReplyRXDrop
OBJECT-TYPE
ARP Reply RX drop counter.
1.3.6.1.4.1.6321.1.2.3.1.13.16.3.1.6Counter32read-onlycurrent
enetStats
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.13.17
enetSfpInfoTable
OBJECT-TYPE
This table includes sfp info of enet port.
1.3.6.1.4.1.6321.1.2.3.1.13.17.2not-accessiblecurrent
enetSfpInfoEntry
OBJECT-TYPE
An entry in enetSfpInfoTable.
1.3.6.1.4.1.6321.1.2.3.1.13.17.2.1not-accessiblecurrent
enetSfpInfoTxpower
OBJECT-TYPE
Measured Tx Output Power.
1.3.6.1.4.1.6321.1.2.3.1.13.17.2.1.1INTEGER (1..65535)read-onlycurrent
enetSfpInfoRxpower
OBJECT-TYPE
Measured Rx Output Power.
1.3.6.1.4.1.6321.1.2.3.1.13.17.2.1.2INTEGER (1..65535)read-onlycurrent
enetSfpInfoTemperature
OBJECT-TYPE
Measured temperature.
1.3.6.1.4.1.6321.1.2.3.1.13.17.2.1.3INTEGER (-1280000..1280000)read-onlycurrent
enetSfpInfoTxBias
OBJECT-TYPE
Measured tx bias.
1.3.6.1.4.1.6321.1.2.3.1.13.17.2.1.4INTEGER (0..131000)read-onlycurrent
enetSfpInfoVoltage
OBJECT-TYPE
Measured voltage.
1.3.6.1.4.1.6321.1.2.3.1.13.17.2.1.5INTEGER (0..65000)read-onlycurrent
adslStats
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.13.18
adslPortUtilTable
OBJECT-TYPE
This table includes adsl port utilization.
1.3.6.1.4.1.6321.1.2.3.1.13.18.1not-accessiblecurrent
adslPortUtilEntry
OBJECT-TYPE
An entry in adslPortUtilEntry.
1.3.6.1.4.1.6321.1.2.3.1.13.18.1.1not-accessiblecurrent
adslPortUtilTx
OBJECT-TYPE
Measure adsl port's tx utilization.
1.3.6.1.4.1.6321.1.2.3.1.13.18.1.1.1INTEGER (0..100)read-onlycurrent
adslPortUtilRx
OBJECT-TYPE
Measure adsl port's rx utilization.
1.3.6.1.4.1.6321.1.2.3.1.13.18.1.1.2INTEGER (0..100)read-onlycurrent
clear
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.14
counterClearTarget
OBJECT-TYPE
This managed object is used for identify the target on which the counter would be cleared. The target is encoded as: Byte 1: reserved Byte 2~3: reserved Byte 4: reserved Byte 5~11:each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc.
1.3.6.1.4.1.6321.1.2.3.1.14.1OCTET STRINGread-writecurrent
counterClearOps
OBJECT-TYPE
The corresponding bit is set to 1 to start the operation. The various bit positions are: BIT 1: clear interface counters BIT 2: clear pvc packet counters BIT 3: clear port ATM counters BIT 4: clear pvc ATM counters BIT 5: clear DHCP counters BIT 6: clear IGMP counters BIT 7: clear IGMP port counters BIT 8: clear MACFF ARP counters BIT 9: clear current lineperf BIT 10: clear current 15 minute lineperf BIT 11: clear current 1 day lineperf
1.3.6.1.4.1.6321.1.2.3.1.14.2INTEGERread-writecurrent
counterClearVpi
OBJECT-TYPE
VPI of the pvc whose counters would be cleared.
1.3.6.1.4.1.6321.1.2.3.1.14.3INTEGER (0..255)read-writecurrent
counterClearVci
OBJECT-TYPE
VCI of the pvc whose counters would be cleared.
1.3.6.1.4.1.6321.1.2.3.1.14.4INTEGER (1..65535)read-writecurrent
aesSeriesCommon
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.97
iesSeriesCommon
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.98
accessSwitchCommonATM
OBJECT-IDENTITY
1.3.6.1.4.1.6321.1.2.3.1.99