CONFIG-MIB
- Registered at
- 1.3.6.1.4.1.11.2.14.11.5.1.7.1
- Namespace
- hp
- Source file
CONFIG-MIB- Digest
sha256:fa0aae09648caf779a012b9fe04a21f37e514180ef597daf76033dfca40e988e
Imports
| From | Symbols |
|---|---|
| BRIDGE-MIB | dot1dStpPortDesignatedBridge, dot1dStpPortDesignatedPort, dot1dStpPortState |
| HP-ICF-OID | hpSwitch |
| HP-ICF-TC | ConfigStatus, HpSwitchPortType |
| INET-ADDRESS-MIB | InetAddress, InetAddressType |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP |
| SNMPv2-SMI | Counter32, IpAddress, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TRAP-TYPE, iso |
| SNMPv2-TC | DisplayString, MacAddress, RowStatus, TEXTUAL-CONVENTION, TimeStamp, TruthValue |
Imported by
2 module(s) in this corpus import this one.
Load order
Every file a consumer needs in order to load this module, dependencies first.
BRIDGE-MIB CONFIG-MIB HP-ICF-OID HP-ICF-TC IANAifType-MIB IF-MIB INET-ADDRESS-MIB SNMPv2-CONF SNMPv2-MIB SNMPv2-SMI SNMPv2-TC
Under this module's arcs
Where the registration tree carries on below this module.
| Arc | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.29 | hpSwitchBasicConfigMIB | HP-SWITCH-BASIC-CONFIG-MIB |
Textual conventions
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| Timeout type | ||||
| VlanID type |
Objects
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| hpConfig OBJECT-IDENTITY | 1.3.6.1.4.1.11.2.14.11.5.1.7 | |||
| hpSwitchConfig OBJECT-IDENTITY | 1.3.6.1.4.1.11.2.14.11.5.1.7.1 | |||
| hpSwitchTraps OBJECT-IDENTITY | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.0 | |||
| hpSwitchTrapsObjects OBJECT-IDENTITY | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.0.1 | |||
| hpSwitchStpErrantBpduDetector OBJECT-TYPE The identifier of the feature generating Errant BPDU trap. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.0.1.1 | INTEGER {bpduFilter(1), bpduProtection(2), pvstFilter(3), pvstProtection(4)} | accessible-for-notify | optional |
| hpSwitchStpErrantBpduSrcMac OBJECT-TYPE The source MAC address of the port sending Errant STP BPDU. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.0.1.2 | MacAddress | accessible-for-notify | optional |
| hpSwitchSystemConfig OBJECT-IDENTITY | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.1 | |||
| hpSwitchAutoReboot OBJECT-TYPE If the value of this variable was set to yes(1), booting will conditionally enable all application modules-the spanning tree, IP and IPX etc.. Otherwise every application module must be manually enabled through Network Control Language Interpreter's ENABLE command. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.1.1 | INTEGER {yes(1), no(2)} | read-write | mandatory |
| hpSwitchTimeZone OBJECT-TYPE The number of minutes to the east of Greenwich Mean Time(GMT). For a location west of GMT, use a negative integer. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.1.2 | INTEGER (-720..840) | read-write | mandatory |
| hpSwitchDaylightTimeRule OBJECT-TYPE The daylight savings time rule for use by the Internet's RFC 868 Time protocol. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.1.3 | INTEGER {none(1), alaska(2), canadaAndContinentalUS(3), middleEuropeAndPortugal(4), southernHemisphere(5), westernEurop(6), userDefined(7)} | read-write | mandatory |
| hpSwitchDaylightBeginningMonth OBJECT-TYPE The month that daylight saving time starts if DaylightTimeRule is set to userDefined. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.1.4 | INTEGER (1..12) | read-write | mandatory |
| hpSwitchDaylightBeginningDay OBJECT-TYPE The day of the month that daylight saving time starts if DaylightTimeRule is set to userDefined. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.1.5 | INTEGER (1..31) | read-write | mandatory |
| hpSwitchDaylightEndingMonth OBJECT-TYPE The month that daylight saving time ends if DaylightTimeRule is set to userDefined. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.1.6 | INTEGER (1..12) | read-write | mandatory |
| hpSwitchDaylightEndingDay OBJECT-TYPE The day of the month that daylight saving time emds if DaylightTimeRule is set to userDefined. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.1.7 | INTEGER (1..31) | read-write | mandatory |
| hpSwitchSystemConfigStatus OBJECT-TYPE The configuration status of this group of objects. If one or more variables in this group were reconfigurated since last reboot and required reboot to take effect, the value of this variable will be set to notInService. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.1.8 | ConfigStatus | read-only | mandatory |
| hpSwitchSystemPortLEDMode OBJECT-TYPE The mode of the port LED can be either link/activity (link for 3 seconds then activity thereafter) or link-only. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.1.9 | INTEGER {link-activity(1), link-only(2)} | read-write | mandatory |
| hpSwitchControlUnknownIPMulticast OBJECT-TYPE When enabled along with IGMP, any IP Multicast packets that are not already controlled by IGMP will be restricted to ports that have detected a multicast router or ports configured to always forward IP multicast. When set to disabled or when IGMP is disabled, the unknown IP Multicast packets will be flooded out all ports in the VLAN | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.1.10 | INTEGER {enable(1), disable(2)} | read-write | mandatory |
| hpSwitchIgmpDelayedGroupFlushTimer OBJECT-TYPE This feature is disabled by default, which is indicated by a timer value of 0 seconds. When IGMP is enabled and the value of the Delayed Group Flush Timer is not zero, traffic filters for any previously-joined IGMP groups which no longer have active members will persist for the number of seconds indicated by the timer. This has the effect of dropping any additional unjoined traffic for an empty group until the Delayed Group Flush Timer expires, at which time the traffic filter is then removed. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.1.11 | INTEGER (0..255) | read-write | mandatory |
| hpSwitchMaxFrameSize OBJECT-TYPE This is the value of the global jumbos max-frame-size supported by the switch. The default value for this is set to 9216, in order to make it compatible with previous versions of software. This configuration does not take a reboot to take effect. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.1.12 | INTEGER (1..65535) | read-write | mandatory |
| hpSwitchIpMTU OBJECT-TYPE This is the value of the global jumbos IP MTU or L3 MTU supported by the switch. The default value for this is set to 9198, in order to make it compatible with previous versions of software. This configuration does not take a reboot to take effect. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.1.13 | INTEGER (1..65535) | read-write | mandatory |
| hpSwitchConsoleConfig OBJECT-IDENTITY | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.2 | |||
| hpSwitchTelnetAdminStatus OBJECT-TYPE The status of the console telnet operation. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.2.1 | INTEGER {enable(1), disable(2)} | read-write | obsolete |
| hpSwitchTerminalType OBJECT-TYPE Terminal type of the console device. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.2.2 | INTEGER {vt100(2), ansi(4)} | read-write | mandatory |
| hpSwitchConsoleRefRate OBJECT-TYPE The rate, in second per cycle, at which the display of various switch measurements. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.2.3 | INTEGER {refRate1(1), refRate3(3), refRate5(5), refRate10(10), refRate20(20), refRate30(30), refRate45(45), refRate(60)} | read-write | mandatory |
| hpSwitchDisplayedEvent OBJECT-TYPE The type of event messages are automatically displayed on the console. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.2.4 | INTEGER {none(1), major(2), notInfo(3), all(4), debug(5)} | read-write | mandatory |
| hpSwitchConsoleConfigStatus OBJECT-TYPE The configuration status of this group of objects. If one or more variables in this group were reconfigurated since last reboot and required reboot to take effect, the value of this variable will be set to notInService. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.2.5 | ConfigStatus | read-only | mandatory |
| hpSwitchPortConfig OBJECT-IDENTITY | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.3 | |||
| hpSwitchPortTable OBJECT-TYPE A table that contains information about the current port status in this device. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.3.1 | not-accessible | mandatory | |
| hpSwitchPortEntry OBJECT-TYPE Information about a specific port status in this device. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.3.1.1 | not-accessible | mandatory | |
| hpSwitchPortIndex OBJECT-TYPE The ifIndex value which uniquely identifies a row in the Interfaces Table. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.3.1.1.1 | INTEGER (1..65535) | read-only | mandatory |
| hpSwitchPortType OBJECT-TYPE The type of port. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.3.1.1.2 | HpSwitchPortType | read-only | mandatory |
| hpSwitchPortDescr OBJECT-TYPE A textual string containing information about the interface. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.3.1.1.3 | DisplayString (SIZE(0..255)) | read-only | mandatory |
| hpSwitchPortAdminStatus OBJECT-TYPE The desired state of the interface. This variable is similar to the ifAdminStatus but instead of keeping the operational status, this variable maintain the desired state in the configuration data base. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.3.1.1.4 | INTEGER {enable(1), disable(2)} | read-write | obsolete |
| hpSwitchPortEtherMode OBJECT-TYPE The type of transmission on this port. This variable is valid only if the hpSwitchPortType was Ethernet. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.3.1.1.5 | INTEGER {half-duplex(1), full-duplex(2)} | read-write | mandatory |
| hpSwitchPortVgMode OBJECT-TYPE The type of transmission on this port. This variable is valid only if the hpSwitchPortType was VG. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.3.1.1.6 | INTEGER {master(1), endNode(2), autoDetect(3)} | read-write | mandatory |
| hpSwitchPortLinkbeat OBJECT-TYPE The linkbeat status of this port. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.3.1.1.7 | INTEGER {enable(1), disable(2)} | read-write | mandatory |
| hpSwitchPortTrunkGroup OBJECT-TYPE The trunk group this port belong to. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.3.1.1.8 | INTEGER (0..65535) | read-write | mandatory |
| hpSwitchPortBcastLimit OBJECT-TYPE The percentage of network bandwidth consumed by broadcast traffic through this port. If the value of this variable is 0, there will be no broadcast limit. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.3.1.1.9 | INTEGER (0..99) | read-write | mandatory |
| hpSwitchPortFastEtherMode OBJECT-TYPE The type of transmission on this port. This variable is valid only if the hpSwitchPortType was Fast Ethernet. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.3.1.1.10 | INTEGER {half-duplex-10Mbits(1), half-duplex-100Mbits(2), full-duplex-10Mbits(3), full-duplex-100Mbits(4), auto-neg(5), full-duplex-1000Mbits(6), auto-10Mbits(7), auto-100Mbits(8), auto-1000Mbits(9), full-duplex-10Gbits(10), auto-10-100Mbits(11)} | read-write | mandatory |
| hpSwitchPortFlowControl OBJECT-TYPE The Flow Control of this port. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.3.1.1.11 | INTEGER {disable(1), enable(2)} | read-write | mandatory |
| hpSwitchPortTrunkType OBJECT-TYPE Used in conjunction with hpSwitchPortTrunkGroup to determine what type of trunk and which group it belongs to. If hpSwitchPortTrunkGroup is set to 0, trunking is disabled on the port and this variable becomes a 'don't care' | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.3.1.1.13 | INTEGER {trunk(1), fecAuto(2), saTrunk(3), lacpTrk(4), none(5)} | read-write | mandatory |
| hpSwitchPortTrunkLACPStatus OBJECT-TYPE Used in conjunction with hpSwitchPortTrunkType. When the trunk is a LACP trunk, this variable defines its administrative status | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.3.1.1.14 | INTEGER {disabled(1), active(2), passive(3)} | read-write | mandatory |
| hpSwitchPortMDIXStatus OBJECT-TYPE Shows the MDI/MDIX setting for an RJ-45 port. Returns a value of 'not-applicable' for all ports except RJ-45 ports. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.3.1.1.15 | INTEGER {not-applicable(1), mdi(2), mdix(3), automdix(4)} | read-only | mandatory |
| hpSwitchPortAutoMDIX OBJECT-TYPE Sets the MDI/MDIX value for an RJ-45 port. Negates need for crossover cables. 'automdix', 'mdi', or 'mdix' may be set when the port configuration is set to any auto-negotiation mode, for example 'auto' or 'auto-100', or to any of the fixed-configuration modes, for example '100-full'. The MDI/MDIX value is maintained across port configuration mode changes. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.3.1.1.16 | INTEGER {not-applicable(1), mdi(2), mdix(3), automdix(4)} | read-write | mandatory |
| hpSwitchPortConfigStatus OBJECT-TYPE The configuration status of this group of objects. If one or more variables in this group were reconfigured since last reboot and required reboot to take effect, the value of this variable will be set to notInService. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.3.2 | ConfigStatus | read-only | mandatory |
| hpSwitchIpxConfig OBJECT-IDENTITY | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.4 | |||
| hpSwitchIpxConfigStatus OBJECT-TYPE The status of the IPX configuration table. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.4.2 | ConfigStatus | read-only | mandatory |
| hpSwitchIpConfig OBJECT-IDENTITY | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.5 | |||
| hpSwitchIpTimepAdminStatus OBJECT-TYPE The operational status of the Time protocol. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.5.1 | INTEGER {manual(1), disable(2), dhcp(3)} | read-write | mandatory |
| hpSwitchIpTimepServerAddr OBJECT-TYPE ### deprecated ### The IP address of the Time server. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.5.2 | IpAddress | read-write | deprecated |
| hpSwitchIpTimepPollInterval OBJECT-TYPE The client poll interval of the Time server in minutes. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.5.3 | INTEGER (1..65535) | read-write | mandatory |
| hpSwitchIpConfigStatus OBJECT-TYPE The configuration status of the Timep and IP related objects. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.5.5 | ConfigStatus | read-only | obsolete |
| hpSwitchIpTftpMode OBJECT-TYPE The operational mode of the Tftp protocol. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.5.6 | INTEGER {secure(1), unsecure(2)} | read-write | mandatory |
| hpSwitchIpTimepInetServerAddrType OBJECT-TYPE The IP address type of the Time server. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.5.7 | InetAddressType | read-write | mandatory |
| hpSwitchIpTimepInetServerAddr OBJECT-TYPE The IP address (of the Time server)to which this entry's addressing information pertains. hpSwitchIpTimepInetServerAddr is always interpreted within the context of hpSwitchIpTimepInetServerAddrType. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.5.8 | InetAddress | read-write | mandatory |
| hpSwitchSerialLinkConfig OBJECT-IDENTITY | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.6 | |||
| hpSwitchSLinkBaudRate OBJECT-TYPE The rate of data transfer between the console and the node. baudRate1 is speed sense. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.6.1 | INTEGER {speedSense(1), baudRate300(2), baudRate600(3), baudRate1200(4), baudRate2400(5), baudRate4800(6), baudRate9600(7), baudRate19200(8), baudRate38400(9), baudRate57600(10), baudRate115200(11)} | read-write | mandatory |
| hpSwitchSLinkFlowCtrl OBJECT-TYPE The flow-control mechanism between the console and the switch. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.6.2 | INTEGER {none(1), xonXoff(2), robustXonXoff(3)} | read-write | mandatory |
| hpSwitchSLinkConnInactTime OBJECT-TYPE The number of minutes to wait after no character was input to log out the console. Valid values are 0 (not to log out of the console for inactivity) through 120 (two hours). | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.6.3 | INTEGER (0..120) | read-write | mandatory |
| hpSwitchSLinkModemConnTime OBJECT-TYPE The number of seconds to wait for data mode and clear to send and receiver ready signals after asserting request to send and terminal ready signals. Valid values are 0 (switch will wait forever for the modem) through 300 (5 minutes). | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.6.4 | INTEGER (0..300) | read-write | mandatory |
| hpSwitchSLinkModemLostRecvTime OBJECT-TYPE The number of milliseconds the receiver ready signal is allowed to drop before the switch will disconnect the modem. Valid values are 0 (the switch will wait forever) through 5000 (5 seconds). | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.6.5 | INTEGER (0..5000) | read-write | mandatory |
| hpSwitchSLinkModemDisConnTime OBJECT-TYPE The number of seconds to wait after the modem is disconnected before allowing the modem to be reconnected. Valid values are 0 (allow a connection as soon as possible, the default) through 60 (1 minute). | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.6.6 | INTEGER (0..60) | read-write | mandatory |
| hpSwitchSLinkParity OBJECT-TYPE The type of parity to use between the console and the node. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.6.7 | INTEGER {parityNone(1), parityOdd(2), parityEven(3)} | read-only | mandatory |
| hpSwitchSLinkCharBits OBJECT-TYPE The number of bits per character to use between the console and the node. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.6.8 | INTEGER {char8Bits(1), char7Bits(2)} | read-only | mandatory |
| hpSwitchSLinkStopBits OBJECT-TYPE The number of stop bots to use when communicating between the console and the node. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.6.9 | INTEGER {stop1Bits(1), stop1andHalfBits(2), stop2Bits(3)} | read-only | mandatory |
| hpSwitchSLinkConfigStatus OBJECT-TYPE The configuration status of this group of objects. If one or more variables in this group were reconfigured since last reboot and required reboot to take effect, the value of this variable will be set to notInService. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.6.10 | ConfigStatus | read-only | mandatory |
| hpSwitchFilterConfig OBJECT-IDENTITY | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.8 | |||
| hpSwitchFilterConfigTable OBJECT-TYPE A table that contains information about the traffic filter configuration in this device. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.8.1 | not-accessible | mandatory | |
| hpSwitchFilterConfigEntry OBJECT-TYPE Information about a traffic filter configuration in this device. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.8.1.1 | not-accessible | mandatory | |
| hpSwitchFilterIndex OBJECT-TYPE An index that uniquely identifies a traffic filter for which this entry contains information. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.8.1.1.1 | INTEGER (1..65535) | read-only | mandatory |
| hpSwitchFilterType OBJECT-TYPE The type of filter. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.8.1.1.2 | INTEGER {multicast(1), level-3(2), port(3), unicast(4)} | read-write | mandatory |
| hpSwitchFilterSrcPort OBJECT-TYPE This variable is required when a port filter or unicast filter was configurated. It will be ignored otherwise. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.8.1.1.3 | INTEGER (1..65535) | read-write | mandatory |
| hpSwitchFilterMacAddr OBJECT-TYPE This variable is valid only if a unicast or multicast filter was defined. It will be ignored otherwise. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.8.1.1.4 | MacAddress | read-write | mandatory |
| hpSwitchFilterProtocolType OBJECT-TYPE This variable is valid only if a level-3 filter was defined. It will be ignored otherwise. This variable will contain either a etherType (DIX Ethernet) or SAP(IEEE 802) value of the level-3 protocol. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.8.1.1.5 | INTEGER (1..65535) | read-write | mandatory |
| hpSwitchFilterPortMask OBJECT-TYPE This variable specifies a group of ports whose traffic will be filtered. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the switch is represented by a single bit within the value of this object. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.8.1.1.6 | OCTET STRING | read-write | mandatory |
| hpSwitchFilterEntryStatus OBJECT-TYPE The status of a filter entry. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.8.1.1.7 | RowStatus | read-write | mandatory |
| hpSwitchProbeConfig OBJECT-IDENTITY | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.9 | |||
| hpSwitchProbeType OBJECT-TYPE If the value of this variable is equal to 1, the probe will monitor those ports specified by hpSwitchProbedPortMask, otherwise all of the port belong to the virtual LAN specified by hpSwitchProbedVlanId will be monitored. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.9.1 | INTEGER {ports(1), vlan(2)} | read-write | obsolete |
| hpSwitchProbedVlanId OBJECT-TYPE The probed virtual LAN. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.9.2 | VlanID | read-write | obsolete |
| hpSwitchProbePort OBJECT-TYPE The port that every packet passes through those probed ports will be copied to. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.9.3 | INTEGER (1..65535) | read-write | obsolete |
| hpSwitchProbeAdminStatus OBJECT-TYPE The operational status of the probing function | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.9.4 | INTEGER {enable(1), disable(2)} | read-write | obsolete |
| hpSwitchProbedPortMask OBJECT-TYPE This variable specifies a group of ports which will be probed. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the switch is represented by a single bit within the value of this object. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.9.5 | OCTET STRING | read-write | obsolete |
| hpSwitchFddiIpFragConfig OBJECT-IDENTITY | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.11 | |||
| hpSwitchFddiIpFragConfigTable OBJECT-TYPE A list of IP fragmentation configuration parameters for the FDDI cards in the switch. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.11.1 | not-accessible | mandatory | |
| hpSwitchFddiIpFragConfigEntry OBJECT-TYPE An Fddi IP fragmentation entry which is containing configurable options for the FDDI cards in the switch. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.11.1.1 | not-accessible | mandatory | |
| hpSwitchFddiIpFragConfigIndex OBJECT-TYPE A unique value for each FDDI Card. The value for each FDDI card must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.11.1.1.1 | INTEGER (1..65535) | read-only | mandatory |
| hpSwitchFddiIpFragConfigStatus OBJECT-TYPE The operational status of FDDI IP fragmentation for each FDDI card. enable(1): FDDI card will fragment all packets which are bigger then the Ethernet packet size limitation, 1518 Bytes. disable(2): FDDI card will drop all packets which are bigger then the Ethernet packet size limitation, 1518 Bytes. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.11.1.1.2 | INTEGER {enable(1), disable(2)} | read-write | mandatory |
| hpSwitchABCConfig OBJECT-IDENTITY | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.12 | |||
| hpSwitchABCConfigTable OBJECT-TYPE A list of Automatic Broadcast Control (ABC disable/enable entries for each VLAN on the switch. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.12.1 | not-accessible | mandatory | |
| hpSwitchABCConfigEntry OBJECT-TYPE Contains the ABC status for each VLAN on the switch, including IP RIP control and IPX RIP/SAP control. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.12.1.1 | not-accessible | mandatory | |
| hpSwitchABCConfigVlan OBJECT-TYPE The user is able to enable/disable ABC on a per VLAN basis, so the VLAN serves as an index into the ABC configuration table. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.12.1.1.1 | VlanID | read-only | mandatory |
| hpSwitchABCConfigControl OBJECT-TYPE ABC control is either IP&IPX or IP or IPX or disabled for each VLAN on the switch. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.12.1.1.2 | INTEGER {ipipx(1), ip(2), ipx(3), disable(4)} | read-write | mandatory |
| hpSwitchABCConfigIpRipControl OBJECT-TYPE IP RIP control. If this feature is enabled then IP RIP packets will only be forwarded on ports, within its VLAN domain, that have heard RIPs before. If this feature is disabled then IP RIP packets seen by a given port will be forwarded to all ports within its VLAN domain. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.12.1.1.3 | INTEGER {enable(1), disable(2)} | read-write | mandatory |
| hpSwitchABCConfigIpxRipSapControl OBJECT-TYPE IPX RIP/SAP control. If this feature is enabled then IPX RIP/SAP packets will only be forwarded on ports, within its VLAN domain, that have previously seen RIP/SAP packets. If this feature is disabled then IPX RIP and SAP packets seen by a given port will be forwarded to all ports within its VLAN domain. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.12.1.1.4 | INTEGER {enable(1), disable(2)} | read-write | mandatory |
| hpSwitchABCConfigVlanBcastLimit OBJECT-TYPE The percentage of network bandwidth consumed by broadcast traffic through VLAN. If the value of this variable is 0, there will be no broadcast limit. There is a default value chosen when ABC is enabled. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.12.1.1.5 | INTEGER (0..99) | read-write | mandatory |
| hpSwitchABCConfigAutoGatewayConfig OBJECT-TYPE If this feature is enabled then DHCP packets both ucast and bcast with UDP destination port 68 will be intercepted. DHCP packets with the router option in the options field in the DHCP message will be modified so that the first daddress in the router option is the same as the clients address. Thus the client will be its own default gateway. If this feature is disabled DHCP packtes will be forwarded as usual. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.12.1.1.7 | INTEGER {enable(1), disable(2)} | read-write | mandatory |
| hpSwitchStpConfig OBJECT-IDENTITY | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14 | |||
| hpSwitchStpVlanTable OBJECT-TYPE A table that contains vlan-specific information for the Spanning Tree Protocol. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.1 | not-accessible | mandatory | |
| hpSwitchStpVlanEntry OBJECT-TYPE A list of information maintained by every port about the Spanning Tree Protocol state for that port. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.1.1 | not-accessible | mandatory | |
| hpSwitchStpVlan OBJECT-TYPE The operational status of the spanning tree protocol. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.1.1.1 | VlanID | read-only | mandatory |
| hpSwitchStpAdminStatus OBJECT-TYPE The operational status of the spanning tree protocol. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.1.1.2 | INTEGER {enable(1), disable(2)} | read-write | mandatory |
| hpSwitchStpPriority OBJECT-TYPE The value of the write-able portion of the Bridge ID, i.e., the first two octets of the (8 octet long) Bridge ID. The other (last) 6 octets of the Bridge ID are given by the value of dot1dBaseBridgeAddress. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.1.1.3 | INTEGER (0..65535) | read-write | mandatory |
| hpSwitchStpMaxAge OBJECT-TYPE The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.1.1.4 | Timeout | read-write | mandatory |
| hpSwitchStpHelloTime OBJECT-TYPE The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.1.1.5 | Timeout | read-write | mandatory |
| hpSwitchStpForwardDelay OBJECT-TYPE This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. [Note that this value is the one that this bridge is currently using, in contrast to dot1dBridgeForwardDelay which is the value that this bridge and all others would start using if/when this bridge were to become the root.] | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.1.1.6 | Timeout | read-write | mandatory |
| hpSwitchStpPortTable OBJECT-TYPE A table that contains port-specific information for the Spanning Tree Protocol. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.2 | not-accessible | mandatory | |
| hpSwitchStpPortEntry OBJECT-TYPE A list of information maintained by every port about the Spanning Tree Protocol state for that port. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.2.1 | not-accessible | mandatory | |
| hpSwitchStpPort OBJECT-TYPE The port number of the port for which this entry contains Spanning Tree Protocol management information. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.2.1.1 | INTEGER (1..65535) | read-only | mandatory |
| hpSwitchStpPortType OBJECT-TYPE The type of port. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.2.1.2 | HpSwitchPortType | read-only | mandatory |
| hpSwitchStpPortSrcMac OBJECT-TYPE The source MAC address used by the spanning tree protocol. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.2.1.3 | MacAddress | read-only | mandatory |
| hpSwitchStpPortPriority OBJECT-TYPE The value of the priority field which is contained in the first (in network byte order) octet of the (2 octet long) Port ID. The other octet of the Port ID is given by the value of dot1dStpPort. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.2.1.4 | INTEGER (0..255) | read-write | mandatory |
| hpSwitchStpPortPathCost OBJECT-TYPE The contribution of this port to the path cost of paths towards the spanning tree root which include this port. 802.1D-1990 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.2.1.5 | INTEGER (1..65535) | read-write | mandatory |
| hpSwitchStpPortMode OBJECT-TYPE If the value of this variable is set to fast(2), the port will go directly into the Forwarding State when a device is connected to it. Use this feature only on ports that are connected to an individual PC or Workstation, to allow these ports to come up and move quickly to the Forwarding State instead of going through the normal STP initialization process. Caution: Changing the value of this variable to fast(2) on ports connected to a hub or switch may cause loops in your network. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.2.1.6 | INTEGER {normal(1), fast(2), uplink(3)} | read-write | mandatory |
| hpSwitchStpPortBpduFilter OBJECT-TYPE Setting True will cause port to ignore ingress BPDUs and not generate egress BPDUs, as the result the port will stay in forwarding state. Default is False. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.2.1.7 | INTEGER {true(1), false(2)} | read-write | optional |
| hpSwitchStpPortBpduProtection OBJECT-TYPE Setting True indicates that no BPDUs are expected to be received on this port. At the reception of BPDUs the BPDU protection mechanism will disable this port and port will transition into bpduError state. Default is False. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.2.1.8 | INTEGER {true(1), false(2)} | read-write | optional |
| hpSwitchStpPortErrantBpduCounter OBJECT-TYPE Counts the number of BPDUs that were not expected to be received on this port. This counter gets incremented only if hpSwitchStpPortBpduProtection, hpSwitchStpPortBpduFilter, hpSwitchStpPortPvstFilter, or hpSwitchStpPvstProtection is True for the port, otherwise it is cleared to zero. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.2.1.9 | Counter | read-only | optional |
| hpSwitchStpPortPvstFilter OBJECT-TYPE Setting True will cause the port to ignore incoming PVST BPDUs. Default is False. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.2.1.10 | TruthValue | read-write | optional |
| hpSwitchStpPortPvstProtection OBJECT-TYPE Setting True indicates that any PVST BPDUs arriving on this port should be discarded and that this will cause the port to be disabled. The port will remain disabled for the time period indicated by hpSwitchStpBpduProtectionTimeout. Default is False. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.2.1.11 | TruthValue | read-write | optional |
| hpSwitchStpTrapCntl OBJECT-TYPE Controls generation of SNMP traps by STP-enabled switch for events defined in this MIB. The set bit means 'enabled'. - errantBpdu(0) The state of this bit specifies whether the notification trap allowed to be send when unexpected (errant) BPDU is received on a port. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.3 | Bits {errantBpdu(0)} | read-write | optional |
| hpSwitchStpBpduProtectionTimeout OBJECT-TYPE The duration of time in seconds when a protected port affected by receiving of an unauthorized BPDU will remain in down state. The zero value means infinity. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.4 | INTEGER | read-write | optional |
| hpSwitchIgmpConfig OBJECT-IDENTITY | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.15 | |||
| hpSwitchIgmpConfigTable OBJECT-TYPE A table that contains information about the IGMP Querier capacity or High Priority Forward configuration on any given vlan on the switch. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.1 | not-accessible | mandatory | |
| hpSwitchIgmpConfigEntry OBJECT-TYPE Information about the IGMP Querier feature associated with a specific virtal LAN in this device. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.1.1 | not-accessible | mandatory | |
| hpSwitchIgmpVlanIndex OBJECT-TYPE An index that uniquely identifies the IGMP configuration of a virtual LAN for which this entry contains information. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.1.1.1 | VlanID | read-only | mandatory |
| hpSwitchIgmpState OBJECT-TYPE The operational status of the IGMP support for this virtual LAN. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.1.1.2 | INTEGER {enable(1), disable(2)} | read-write | mandatory |
| hpSwitchIgmpQuerierState OBJECT-TYPE The operational status of the IGMP Querier functionality for this virtual LAN. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.1.1.3 | INTEGER {enable(1), disable(2)} | read-write | mandatory |
| hpSwitchIgmpPriorityState OBJECT-TYPE The operational status of the IGMP Forward with High Priority mode for this virtual LAN. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.1.1.4 | INTEGER {enable(1), disable(2)} | read-write | mandatory |
| hpSwitchIgmpQuerierInterval OBJECT-TYPE The time (in seconds) to wait between Querier election cycles for this virtual LAN. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.1.1.5 | INTEGER (5..300) | read-write | mandatory |
| hpSwitchIgmpPortConfigTable OBJECT-TYPE A table that contains information about the IGMP port configurations on this switch. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.2 | not-accessible | mandatory | |
| hpSwitchIgmpPortConfigEntry OBJECT-TYPE The information associated with each IGMP port configuration. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.2.1 | not-accessible | mandatory | |
| hpSwitchIgmpPortIndex OBJECT-TYPE The ifIndex value which uniquely identifies a row in the Interfaces Table. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.2.1.1 | INTEGER (1..65535) | read-only | mandatory |
| hpSwitchIgmpPortType OBJECT-TYPE The type of port. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.2.1.2 | HpSwitchPortType | read-only | mandatory |
| hpSwitchIgmpIpMcastState OBJECT-TYPE The operational status of the IGMP feature for this port or trunk. 1 implies that all IP Multicast traffic will be monitored on the port, 2 implies that IP Multicast traffic will be dropped on the port, and 3 implies that all IP Multicast traffic will be forwarded without the switch examining it. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.2.1.3 | INTEGER {auto(1), blocked(2), forward(3)} | read-write | mandatory |
| hpSwitchIgmpPortConfigTable2 OBJECT-TYPE A table that contains information about the IGMP port configurations on this switch. This table supercedes hpSwitchIgmpPortConfigTable for products which support multiple VLANs on each port. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.3 | not-accessible | mandatory | |
| hpSwitchIgmpPortConfigEntry2 OBJECT-TYPE The information associated with each IGMP port configuration. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.3.1 | not-accessible | mandatory | |
| hpSwitchIgmpPortVlanIndex2 OBJECT-TYPE The Vlan Index value which uniquely identifies a row in the Interfaces Table. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.3.1.1 | INTEGER (1..65535) | read-only | mandatory |
| hpSwitchIgmpPortIndex2 OBJECT-TYPE The ifIndex value which uniquely identifies a row in the Interfaces Table. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.3.1.2 | INTEGER (1..65535) | read-only | mandatory |
| hpSwitchIgmpPortType2 OBJECT-TYPE The type of port. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.3.1.3 | HpSwitchPortType | read-only | mandatory |
| hpSwitchIgmpIpMcastState2 OBJECT-TYPE The operational status of the IGMP feature for this port or trunk. 1 implies that all IP Multicast traffic will be monitored on the port, 2 implies that IP Multicast traffic will be dropped on the port, and 3 implies that all IP Multicast traffic will be forwarded without the switch examining it. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.3.1.4 | INTEGER {auto(1), blocked(2), forward(3)} | read-write | mandatory |
| hpSwitchIgmpPortForcedLeaveState OBJECT-TYPE The operational status of the IGMP feature for this port or trunk indicates whether any IGMP V2 Leaves received for an IP Multicast group will cause the group to be deleted after the hpSwitchIgmpForcedLeaveInterval if no new IGMP V2 Reports are received for that group. Normal behavior is for a group issuing a Leave to be deleted after the Querier's Maximum Response time if no IGMP V2 Report is received. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.3.1.5 | INTEGER {enabled(1), disabled(2)} | read-write | mandatory |
| hpSwitchIgmpPortFastLeaveState OBJECT-TYPE The operational status of the IGMP feature for this port or trunk indicates whether any IGMP V2 Leaves received for an IP Multicast group will cause the group to be deleted immediately on single- connection ports. Normal behavior is for a group issuing a Leave to be deleted after the Querier's Maximum Response time if no IGMP V2 Report is received. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.3.1.6 | INTEGER {enabled(1), disabled(2)} | read-write | mandatory |
| hpSwitchIgmpForcedLeaveInterval OBJECT-TYPE When a port's hpSwitchIgmpPortForcedLeaveState is enabled, this is the amount of time allowed for an IGMP V2 Report to arrive and cancel deletion of a multicast group requested by a previous IGMP V2 Leave request. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.4 | INTEGER (1..65535) | read-write | mandatory |
| hpSwitchCosConfig OBJECT-IDENTITY | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17 | |||
| hpSwitchCosPortConfigTable OBJECT-TYPE A table that contains information about the CoS port configurations on this switch. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.1 | not-accessible | mandatory | |
| hpSwitchCosPortConfigEntry OBJECT-TYPE The information associated with each CoS port configuration. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.1.1 | not-accessible | mandatory | |
| hpSwitchCosPortIndex OBJECT-TYPE The ifIndex value which uniquely identifies a row in the Interfaces Table. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.1.1.1 | INTEGER (1..65535) | read-only | mandatory |
| hpSwitchCosPortType OBJECT-TYPE The type of port. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.1.1.2 | HpSwitchPortType | read-only | deprecated |
| hpSwitchCosPortPriority OBJECT-TYPE The 802.1p priority value to assign to packets received on the specified port. This value will be inserted in the 802.1Q tag and the packet will be placed in the appropriate outbound port queue. The value of 255 is used to indicate No Override. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.1.1.3 | INTEGER (0..255) | read-write | mandatory |
| hpSwitchCosPortDSCPPolicy OBJECT-TYPE The DSCP Policy to assign to packets received on the specified Port. This is an index into the hpSwitchCosDSCPPolicy table, or the value 255 indicating no DSCP Policy exists. This policy is associated with an 802.1p priority value, which will be inserted in the 802.1Q tag and will cause the packet to be placed in the appropriate outbound port queue. When the packet is IP protocol type, the DSCP policy value (a Differentiated Services codepoint) will also be written into the Differentiated-Services field of the IP Type-of-Service byte. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.1.1.4 | INTEGER (1..255) | read-write | mandatory |
| hpSwitchCosPortResolvedPriority OBJECT-TYPE The 802.1p priority that will be applied to packets received on the specified port. This value represents the actual operating value for this CoS port entry. A value of 255 represents no override of the incoming priority. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.1.1.5 | INTEGER (0..7 | 255) | read-only | mandatory |
| hpSwitchCosPortApplyPolicy OBJECT-TYPE This object determines which configuration policy, noPolicyOverride, hpSwitchCosPortPriority or hpSwitchCosPortDSCPPolicy, applies for the given Port CoS entry. These configuration policies are mutually exclusive of one another. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.1.1.6 | INTEGER {noPolicyOverride(1), applyHpSwitchCosPortPriority(2), applyHpSwitchCosPortDSCPPolicy(3)} | read-write | mandatory |
| hpSwitchCosVlanConfigTable OBJECT-TYPE A table that contains information about the CoS Vlan configurations on this switch. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.2 | not-accessible | mandatory | |
| hpSwitchCosVlanConfigEntry OBJECT-TYPE The information associated with each CoS Vlan configuration. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.2.1 | not-accessible | mandatory | |
| hpSwitchCosVlanIndex OBJECT-TYPE The index that uniquely identifies the CoS configuration of a virtual LAN for which this entry contains information. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.2.1.1 | VlanID | read-only | mandatory |
| hpSwitchCosVlanPriority OBJECT-TYPE The 802.1p priority value to assign to packets received on the specified Vlan. This value will be inserted in the 802.1Q tag and the packet will be placed in the appropriate outbound port queue. The value of 255 is used to indicate No Override. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.2.1.2 | INTEGER (0..255) | read-write | mandatory |
| hpSwitchCosVlanDSCPPolicy OBJECT-TYPE The DSCP Policy to assign to packets received on the specified Vlan. This is an index into the hpSwitchCosDSCPPolicy table, or the value 255 indicating no DSCP Policy exists. This policy is associated with an 802.1p priority value, which will be inserted in the 802.1Q tag and will cause the packet to be placed in the appropriate outbound port queue. When the packet is IP protocol type, the DSCP policy value (a Differentiated Services codepoint) will also be written into the Differentiated-Services field of the IP Type-of-Service byte. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.2.1.3 | INTEGER (1..255) | read-write | mandatory |
| hpSwitchCosVlanResolvedPriority OBJECT-TYPE The 802.1p priority that will be applied to packets received on the specified VLAN. This value represents the actual operating value for this CoS vlan entry. A value of 255 represents no override of the incoming priority . | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.2.1.4 | INTEGER (0..7 | 255) | read-only | mandatory |
| hpSwitchCosVlanApplyPolicy OBJECT-TYPE This object determines which configuration policy, noPolicyOverride, hpSwitchCosVlanPriority or hpSwitchCosDSCPPolicy, applies for this given Vlan CoS entry. These configuration policies are mutually exclusive of one another. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.2.1.5 | INTEGER {noPolicyOverride(1), applyHpSwitchCosVlanPriority(2), applyHpSwitchCosVlanDSCPPolicy(3)} | read-write | mandatory |
| hpSwitchCosProtocolConfigTable OBJECT-TYPE A table that contains information about the CoS protocol type configurations on this switch. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.3 | not-accessible | mandatory | |
| hpSwitchCosProtocolConfigEntry OBJECT-TYPE The information associated with each CoS protocol configuration. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.3.1 | not-accessible | mandatory | |
| hpSwitchCosProtocolType OBJECT-TYPE Packets with this protocol type will receive the new priority value. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.3.1.1 | INTEGER {ip(1), ipx(2), arp(3), decnet(4), appletalk(5), sna(6), netbios(7)} | read-only | mandatory |
| hpSwitchCosProtocolPriority OBJECT-TYPE The 802.1p priority value to assign to packets received for the specified protocol. This value will be inserted in the 802.1Q tag and the packet will be placed in the appropriate outbound port queue. The value of 255 is used to indicate No Override. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.3.1.2 | INTEGER (0..255) | read-write | mandatory |
| hpSwitchCosAddressConfigTable OBJECT-TYPE A table that contains information about the CoS address configurations on this switch. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.4 | not-accessible | mandatory | |
| hpSwitchCosAddressConfigEntry OBJECT-TYPE The information associated with each CoS address configuration. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.4.1 | not-accessible | mandatory | |
| hpSwitchCosAddressIndex OBJECT-TYPE The index that uniquely identifies the CoS configuration for an address for which this entry contains information. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.4.1.1 | INTEGER (1..65535) | read-only | mandatory |
| hpSwitchCosAddressType OBJECT-TYPE The type of address to configure. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.4.1.2 | INTEGER {ip(1)} | read-write | mandatory |
| hpSwitchCosAddressIp OBJECT-TYPE This variable is valid only if an IP CoS configuration was defined. It will be ignored otherwise. Packets with this IP address as a source or destination will receive the new priority value. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.4.1.3 | IpAddress | read-write | mandatory |
| hpSwitchCosAddressPriority OBJECT-TYPE The 802.1p priority value to assign to packets received for the specified address. This value will be inserted in the 802.1Q tag and the packet will be placed in the appropriate outbound port queue. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.4.1.4 | INTEGER (0..255) | read-write | mandatory |
| hpSwitchCosAddressStatus OBJECT-TYPE The status of a Cos Address entry. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.4.1.5 | RowStatus | read-write | mandatory |
| hpSwitchCosAddressDSCPPolicy OBJECT-TYPE The DSCP Policy to assign to packets received for the specified address. This is an index into the hpSwitchCosDSCPPolicy table, or the value 255 indicating no DSCP Policy exists. This policy is associated with an 802.1p priority value, which will be inserted in the 802.1Q tag and will cause the packet to be placed in the appropriate outbound port queue. The DSCP policy value (a Differentiated Services codepoint) will also be written into the Differentiated-Services field of the IP Type-of-Service byte. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.4.1.6 | INTEGER (1..255) | read-write | mandatory |
| hpSwitchCosAddressResolvedPriority OBJECT-TYPE The 802.1p priority that will be applied to packets received for the specified address. This value represents the actual operating value for this given address entry. A value of 255 represents no override. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.4.1.7 | INTEGER (0..7 | 255) | read-only | mandatory |
| hpSwitchCosAddressApplyPolicy OBJECT-TYPE This object determines which configuration policy, hpSwitchCosAddressPriority or hpSwitchCosDSCPPolicy, applies for the given Address CoS entry. These configuration policies are mutually exclusive of one another. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.4.1.8 | INTEGER {applyHpSwitchCosAddressPriority(1), applyHpSwitchCosAddressDSCPPolicy(2)} | read-write | mandatory |
| hpSwitchCosTosConfig OBJECT-IDENTITY | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.5 | |||
| hpSwitchCosTosConfigMode OBJECT-TYPE The operational status of Type of Service based Class of Service. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.5.1 | INTEGER {disable(1), ipprecedence(2), diffserv(3)} | read-write | mandatory |
| hpSwitchCosTosConfigTable OBJECT-TYPE A table that contains information about the CoS Type of Service configurations on this switch. This table is used only when the hpSwitchCosTosConfigMode is set to diffserv. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.5.2 | not-accessible | mandatory | |
| hpSwitchCosTosConfigEntry OBJECT-TYPE The information associated with each CoS TOS configuration. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.5.2.1 | not-accessible | mandatory | |
| hpSwitchCosTosIndex OBJECT-TYPE Packets with this value in the upper bits of the Type of Service field of the IP protocol header will receive the new priority value. For Differentiated Services the upper 6 bits of the TOS field are used. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.5.2.1.1 | INTEGER | read-only | mandatory |
| hpSwitchCosTosPriority OBJECT-TYPE The 802.1p priority value to assign to packets received for the specified TOS. This value will be inserted in the 802.1Q tag and the packet will be placed in the appropriate outbound port queue. The value of 255 is used to indicate No Override. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.5.2.1.2 | INTEGER (0..255) | read-write | deprecated |
| hpSwitchCosTosDSCPPolicy OBJECT-TYPE The DSCP Policy to assign to packets received for the specified ToS codepoint. This is an index into the hpSwitchCosDSCPPolicy table, or the value 255 indicating no DSCP Policy exists. The DSCP policy is associated with an 802.1p priority value, which will be inserted in the 802.1Q tag and will cause the packet to be placed in the appropriate outbound port queue. The DSCP policy value (a Differentiated Services codepoint) will also replace the incoming value of the Differentiated Services field of the IP Type-of-Service byte. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.5.2.1.3 | INTEGER (1..255) | read-write | mandatory |
| hpSwitchCosTosResolvedPriority OBJECT-TYPE The 802.1p priority that will be applied to packets received for the specified ToS. This value represents the actual operating value for this given ToS entry. A value of 255 represents no override of the incoming priority. If hpSwitchCosTosApplyPolicy is set to applyInheritedPriority, the parallel codepoint in the hpSwitchCosDSCPPolicyConfigTable is used to determine the operating priority. Otherwise if set to applyHpSwitchCosTosDSCPPolicy, the priority for the codepoint that the hpSwitchCosTosDSCPPolicy is indexing will be used. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.5.2.1.4 | INTEGER (0..7 | 255) | read-only | mandatory |
| hpSwitchCosTosApplyPolicy OBJECT-TYPE This object determines which configuration policy, applyInheritedPriority or hpSwitchCosTosDSCPPolicy, applies for the given Tos CoS entry. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.5.2.1.5 | INTEGER {applyInheritedPriority(1), applyHpSwitchCosTosDSCPPolicy(2)} | read-write | mandatory |
| hpSwitchCosDSCPPolicyConfigTable OBJECT-TYPE A table that contains information about the priority applied to each of the Differentiated Services Code Points. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.6 | not-accessible | mandatory | |
| hpSwitchCosDSCPPolicyConfigEntry OBJECT-TYPE A list of objects describing a DiffServe Codepoint (DSCP), and the 802.1p priority to apply for that DSCP. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.6.1 | not-accessible | mandatory | |
| hpSwitchCosDSCPPolicyIndex OBJECT-TYPE An index to uniquely identify each row in the hpSwitchCosDSCPPolicyConfigTable. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.6.1.1 | INTEGER (1..64) | not-accessible | mandatory |
| hpSwitchCosDSCPPolicyPriority OBJECT-TYPE The 802.1p priority value to assign to packets with a given DSCP. This value will be inserted in the 802.1Q tag and the packet will be placed in the appropriate outbound port queue. The value of 255 is used to indicate no override of the incoming priority. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.6.1.2 | INTEGER (0..7 | 255) | read-write | mandatory |
| hpSwitchCosDSCPPolicyName OBJECT-TYPE A user settable name describing a DSCP policy table entry. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.6.1.3 | OCTET STRING (SIZE(0..32)) | read-write | mandatory |
| hpSwitchCosAppTypeConfigTable OBJECT-TYPE A table that contains information about the CoS Application type configurations on the switch. An application is determined by its network source and/or destination port number. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.7 | not-accessible | mandatory | |
| hpSwitchCosAppTypeConfigEntry OBJECT-TYPE An entry in the switch hpSwitchCosAppTypeConfigEntry Table. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.7.1 | not-accessible | mandatory | |
| hpSwitchCosAppTypeConfigIndex OBJECT-TYPE An index to uniquely identify this hpSwitchCosAppType row. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.7.1.1 | INTEGER (1..65535) | not-accessible | mandatory |
| hpSwitchCosAppTypeConfigType OBJECT-TYPE This signifies which network port number to apply to the given CoS Application policy. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.7.1.2 | INTEGER {udpSrcPortConfig(1), udpDestPortConfig(2), udpBothPortsConfig(3), tcpSrcPortConfig(4), tcpDestPortConfig(5), tcpBothPortsConfig(6)} | read-write | mandatory |
| hpSwitchCosAppTypeSrcPort OBJECT-TYPE This object represents the source network port that this policy applies to. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.7.1.3 | INTEGER (1..65535) | read-write | mandatory |
| hpSwitchCosAppTypeDestPort OBJECT-TYPE This object represents the destination network port that this policy applies to. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.7.1.4 | INTEGER (1..65535) | read-write | mandatory |
| hpSwitchCosAppTypePriority OBJECT-TYPE The 802.1p priority that should be applied to packets containing the particular configured source and/or destination port number in this entry. A value of 255 represents that no priority override should take place. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.7.1.5 | INTEGER (0..7 | 255) | read-write | mandatory |
| hpSwitchCosAppTypeDSCPPolicy OBJECT-TYPE The DSCP Policy to assign to packets received for the specified application. This is an index into the hpSwitchCosDSCPPolicy table, or the value 255 indicating no DSCP Policy exists. This policy is associated with an 802.1p priority value, which will be inserted in the 802.1Q tag and will cause the packet to be placed in the appropriate outbound port queue. The DSCP policy value (a Differentiated Services codepoint) will also be written into the Differentiated-Services field of the IP Type-of-Service byte. The value of 255 is used to indicate No Override. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.7.1.6 | INTEGER (1..255) | read-write | mandatory |
| hpSwitchCosAppTypeResolvedPriority OBJECT-TYPE The 802.1p priority that will be applied to packets received on the specified application. This value represents the actual operating value for this CoS application entry. A value of 255 represents no override of the incoming priority | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.7.1.7 | INTEGER (0..7 | 255) | read-only | mandatory |
| hpSwitchCosAppTypeApplyPolicy OBJECT-TYPE This object determines which configuration policy, hpSwitchCosAppTypePriority or hpSwitchCosAppTypeDSCPPolicy, applies for the given AppType CoS entry. These configuration policies are mutually exclusive of one another. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.7.1.8 | INTEGER {applyHpSwitchCosAppTypePriority(1), applyHpSwitchCosAppTypeDSCPPolicy(2)} | read-write | mandatory |
| hpSwitchCosAppTypeStatus OBJECT-TYPE This object is used to create and delete in the hpSwitchCosAppType table. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.7.1.9 | RowStatus | read-write | mandatory |
| hpSwitchCosAppTypeMaxSrcPort OBJECT-TYPE This object represents the maximum source network port that this policy applies to. If a single, specific port is being used and not a range, then value of this object is zero. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.7.1.10 | INTEGER (0..65535) | read-write | mandatory |
| hpSwitchCosAppTypeMaxDestPort OBJECT-TYPE This object represents the maximum destination network port that this policy applies to. If a single, specific port is being used and not a range, then value of this object is zero. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.7.1.11 | INTEGER (0..65535) | read-write | mandatory |
| hpSwitchCosLastChange OBJECT-TYPE The value of the agent's sysUptime when the last time this device experienced a change in the Class of Service configuration. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.8 | TimeStamp | read-only | mandatory |
| hpSwitchConfigCosLastConfigError OBJECT-TYPE The type of the last QoS configuration result or error. This object is updated for each new QoS configuration. It is reset upon reboot. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.9 | INTEGER {aclQosNoError(1), aclQosTooManyRulesError(2), aclQosTooManyMasksError(3)} | read-only | mandatory |
| hpSwitchMeshConfig OBJECT-IDENTITY | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.18 | |||
| hpSwitchMeshMulticastAgingMode OBJECT-TYPE With meshing active, a value of aging will cause learned multicast addresses to be aged out within the required address aging interval. A setting of nonaging will prevent learned multicast addresses from being removed from the switch. Multicast addresses learned while in nonaging mode are not removed until the switch is rebooted. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.18.1 | INTEGER {aging(1), nonaging(2)} | read-write | deprecated |
| hpSwitchMeshBackwardCompatibility OBJECT-TYPE Due to some hardware differences, the Series 1600/24xx/4000/8000 switches cannot be used directly in a mesh environment with Series 5300XL switches. Series 5300XL switches need to emulate the operation of Series 1600/24xx/4000/8000 switches in order to have a heterogeneous mesh working properly. Meshing backward-compatibility feature allows Series 5300XL switches to operate in a compatible mode in which the operation of Series 1600/24xx/4000/8000 switches are emulated. When backward-compatibility is enabled, meshing software will establish connections with Series 1600/24xx/4000/8000 switches and emulate their operation. When backward-compatibility disabled, Series 1600/24xx/4000/8000 switches in the mesh will be ignored by the Series 5300XL switches. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.18.2 | INTEGER {enable(1), disable(2)} | read-write | mandatory |
| hpSwitchPortIsolationConfig OBJECT-IDENTITY | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.19 | |||
| hpSwitchPortIsolationMode OBJECT-TYPE This enables the port isolation feature on the device. Note: Enabling this feature may require VLANS to be configured properly. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.19.1 | INTEGER {enable(1), disable(2)} | read-write | mandatory |
| hpSwitchPortIsolationConfigTable OBJECT-TYPE A table that contains information about the CoS Application type configurations on the switch. An application is determined by its network source and/or destination port number. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.19.2 | not-accessible | mandatory | |
| hpSwitchPortIsolationConfigEntry OBJECT-TYPE An entry in the switch hpSwitchPortIsolationConfigEntry Table. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.19.2.1 | not-accessible | mandatory | |
| hpSwitchPortIsolationPort OBJECT-TYPE An entry in the IfIndex table representing a logical port on this switch. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.19.2.1.1 | INTEGER (1..65535) | not-accessible | mandatory |
| hpSwitchPortIsolationPortMode OBJECT-TYPE Defines the operational mode of a port when Port Isolation feature is enabled. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.19.2.1.2 | INTEGER {uplink(1), public(2), private(3), local(4), group1(5), group2(6)} | read-write | mandatory |
| hpSwitchSshConfig OBJECT-IDENTITY | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.20 | |||
| hpSwitchSshAdminStatus OBJECT-TYPE The status of the SSH operation. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.20.1 | INTEGER {enable(1), disable(2)} | read-write | mandatory |
| hpSwitchSshVersion OBJECT-TYPE The version of the SSH protocol to run. 'version1' will accept connections from v1.3 or v1.5 clients. 'version2' will accept connections only from v2.0 clients. The default is 'version1_or_2' which will accept any connection which can be successfully negotiated. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.20.2 | INTEGER {version1(1), version2(2), version1or2(3)} | read-write | mandatory |
| hpSwitchSshTimeout OBJECT-TYPE The maximum length of time (in seconds) between the wakeup of SSH task and successful protocol negotiation and authentication. The default is 120 seconds. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.20.3 | Timeout (5..120) | read-write | mandatory |
| hpSwitchSshPortNumber OBJECT-TYPE The port number on which SSH daemon should listen for connection requests. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.20.4 | INTEGER (1..65535) | read-write | mandatory |
| hpSwitchSshServerKeySize OBJECT-TYPE Specifies the key size (in bits) of version 1 SSH host rsa key | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.20.5 | INTEGER {bits512(1), bits768(2), bits1024(3)} | read-write | mandatory |
| hpSwitchSshFileServerAdminStatus OBJECT-TYPE Specifies whether or not the SSH daemon will accept and process file transfer requests. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.20.6 | INTEGER {enable(1), disable(2)} | read-write | mandatory |
| hpSwitchSshIpVersion OBJECT-TYPE The types of IP connections SSH will support. 'ipv4' will accept connections from Ipv4 clients. 'ipv6' will accept connections only from ipv6 clients. The default is 'ipv4or6' which will accept Connections from both ipv4 and ipv6 clients. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.20.7 | INTEGER {ipv4(1), ipv6(2), ipv4or6(3)} | read-write | mandatory |
| hpSwitchPendingConfig OBJECT-IDENTITY | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.21 | |||
| hpSwitchPendingConfigControl OBJECT-TYPE The object controls switch pending configuration. If set to the 'applyMstp' value the object applies pending Multiple Spanning Tree Protocol (MSTP) configuration. The 'resetMstp' value, if set, triggers copying of the active MSTP configuration to the pending one. Before the pending configuration is applied its consistency is verified and the request fails if errors are detected. The value the object returns is undefined. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.21.1 | INTEGER {applyMstp(1), resetMstp(2), noAction(3)} | read-write | mandatory |
| hpSwitchBWMinConfig OBJECT-IDENTITY | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.22 | |||
| hpSwitchBWMinEgressPortConfigTable OBJECT-TYPE New definitions under HP-ICF-RATE-LIMIT-MIB. A table that contains information about the port's egress Guaranteed Minimum Bandwidth configurations on this switch. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.22.1 | not-accessible | deprecated | |
| hpSwitchBWMinEgressPortConfigEntry OBJECT-TYPE New definitions under HP-ICF-RATE-LIMIT-MIB. The information associated with each port's egress Guaranteed Minimum Bandwidth configuration. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.22.1.1 | not-accessible | deprecated | |
| hpSwitchBWMinEgressPortIndex OBJECT-TYPE New definitions under HP-ICF-RATE-LIMIT-MIB. The ifIndex value which uniquely identifies a row in the Interfaces Table. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.22.1.1.1 | INTEGER (1..65535) | read-only | deprecated |
| hpSwitchBWMinEgressPortPrctLowPriority OBJECT-TYPE New definitions under HP-ICF-RATE-LIMIT-MIB. The percentage of Guaranteed Minimum bandwidth to be assigned to the egress Low-Priority queue for this port. Total values for all four queues must not exceed 100 percent. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.22.1.1.2 | INTEGER (0..100) | read-write | deprecated |
| hpSwitchBWMinEgressPortPrctNormalPriority OBJECT-TYPE New definitions under HP-ICF-RATE-LIMIT-MIB. The percentage of Guaranteed Minimum bandwidth to be assigned to the egress Normal-Priority queue for this port. Total values for all four queues must not exceed 100 percent. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.22.1.1.3 | INTEGER (0..100) | read-write | deprecated |
| hpSwitchBWMinEgressPortPrctMedPriority OBJECT-TYPE New definitions under HP-ICF-RATE-LIMIT-MIB. The percentage of Guaranteed Minimum bandwidth to be assigned to the egress Medium-Priority queue for this port. Total values for all four queues must not exceed 100 percent. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.22.1.1.4 | INTEGER (0..100) | read-write | deprecated |
| hpSwitchBWMinEgressPortPrctHighPriority OBJECT-TYPE New definitions under HP-ICF-RATE-LIMIT-MIB. The percentage of Guaranteed Minimum bandwidth to be assigned to the egress High-Priority queue for this port. Total values for all four queues must not exceed 100 percent. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.22.1.1.5 | INTEGER (0..100) | read-write | deprecated |
| hpSwitchRateLimitPortConfig OBJECT-IDENTITY | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.23 | |||
| hpSwitchRateLimitPortConfigTable OBJECT-TYPE A table that contains information about the port Rate-Limiting configurations on this switch. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.23.1 | not-accessible | mandatory | |
| hpSwitchRateLimitPortConfigEntry OBJECT-TYPE The information associated with each port's Rate-Limiting configuration. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.23.1.1 | not-accessible | mandatory | |
| hpSwitchRateLimitPortIndex OBJECT-TYPE The ifIndex value which uniquely identifies a row in the Interfaces Table. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.23.1.1.1 | INTEGER (1..65535) | read-only | mandatory |
| hpSwitchRateLimitPortControlMode OBJECT-TYPE The mode by which this port will be Rate-Limited on ingress. If rateLimitPerPortOnly is configured, there will be a single maximum rate for the entire port. If rateLimitPerQueue is configured, the values for each of the four queues indicate the maximum percentage of port traffic that may be received by that queue (the sum of these values must not exceed 100). When rate-limiting is disabled, there are no maximum controls on ingress for this port. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.23.1.1.2 | INTEGER {disabled(1), rateLimitPerPortOnly(2), rateLimitPerQueue(3)} | read-write | mandatory |
| hpSwitchRateLimitPortSingleControlPrct OBJECT-TYPE When hpSwitchRateLimitPortControlMode is configured for rateLimitPerPortOnly, this value is the maximum percentage of traffic that may be received by this port on ingress. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.23.1.1.3 | INTEGER (0..100) | read-write | mandatory |
| hpSwitchRateLimitPortPrctLowPriority OBJECT-TYPE The maximum percentage of traffic that may be received by this port's Low-Priority queue on ingress. hpSwitchRateLimitPortControlMode must be configured to use rateLimitPerQueue for this to take effect. A value of 0-percent for any queue means that no traffic will ever be received on this port for that ingress queue. Total values for all four queues must not exceed 100 percent. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.23.1.1.4 | INTEGER (0..100) | read-write | mandatory |
| hpSwitchRateLimitPortPrctNormalPriority OBJECT-TYPE The maximum percentage of traffic that may be received by this port's Normal-Priority queue on ingress. hpSwitchRateLimitPortControlMode must be configured to use rateLimitPerQueue for this to take effect. A value of 0-percent for any queue means that no traffic will ever be received on this port for that ingress queue. Total values for all four queues must not exceed 100 percent. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.23.1.1.5 | INTEGER (0..100) | read-write | mandatory |
| hpSwitchRateLimitPortPrctMedPriority OBJECT-TYPE The maximum percentage of traffic that may be received by this port's Medium-Priority queue on ingress. hpSwitchRateLimitPortControlMode must be configured to use rateLimitPerQueue for this to take effect. A value of 0-percent for any queue means that no traffic will ever be received on this port for that ingress queue. Total values for all four queues must not exceed 100 percent. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.23.1.1.6 | INTEGER (0..100) | read-write | mandatory |
| hpSwitchRateLimitPortPrctHighPriority OBJECT-TYPE The maximum percentage of traffic that may be received by this port's High-Priority queue on ingress. hpSwitchRateLimitPortControlMode must be configured to use rateLimitPerQueue for this to take effect. A value of 0-percent for any queue means that no traffic will ever be received on this port for that ingress queue. Total values for all four queues must not exceed 100 percent. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.23.1.1.7 | INTEGER (0..100) | read-write | mandatory |
| hpSwitchQosPassThroughMode OBJECT-IDENTITY | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.24 | |||
| hpSwitchQosPassThroughModeConfig OBJECT-TYPE Specify the queue configuration mode for the switch. While changing the queue configuration mode this feature momentarily require to bring down the logical port and after the initialisation of the queues the ports are brought up. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.24.1 | INTEGER {optimized(1), typical(2), balanced(3), onequeue(4)} | read-write | mandatory |
| hpSwitchReboot OBJECT-IDENTITY | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.25 | |||
| hpSwitchRebootConfig OBJECT-TYPE This tells the status of the switch whether it requires reboot for some variable to get effective. The value of this variable can be yes (1) reboot is required. no (2) reboot is not required. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.25.1 | INTEGER {yes(1), no(2)} | read-only | mandatory |
| hpSwitchRebootFastBoot OBJECT-TYPE Specifies whether fastboot is enabled or not on the switch. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.25.2 | INTEGER {enable(1), disable(2)} | read-write | mandatory |
| hpSwitchProtectedPortsConfig OBJECT-IDENTITY | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.26 | |||
| hpSwitchProtectedPortsMask OBJECT-TYPE This variable specifies a group of ports that are not allowed to communicate to each-other. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the switch is represented by a single bit within the value of this object. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.26.1 | OCTET STRING | read-write | mandatory |
Notifications
| Name | OID | Status |
|---|---|---|
| hpSwitchStpErrantBpduReceived NOTIFICATION-TYPE This trap indicates that unexpected (errant) STP BPDU has been received on a port (e.g. on a port that is connected to non-STP device). This notification trap is controlled by the state of 'hpSwitchStpTrapCntl' object. Implementation of this trap is optional. | 1.3.6.1.4.1.11.2.14.11.5.1.7.1.0.0.1 |