CISCOSB-IPv6

OBJECT-TYPE

This table is parallel to ipAddressTable, and is used to add/delete IPv6 entries to/from that table. It contains private objects.

OBJECT-TYPE

An address mapping for a particular interface.

OBJECT-TYPE

The prefix length of this address.

OBJECT-TYPE

Extend standard field ipAddressType to multicast

OBJECT-TYPE

This table is parallel to ipv6InterfaceTable, and is used to configure additional interface parameters.

OBJECT-TYPE

Additional configuration parameters for a particular interface.

OBJECT-TYPE

ND Duplicated address detection number of attempts.

OBJECT-TYPE

Enables or disables Stateless Address Auto configuration on specific interface.

OBJECT-TYPE

Enables or disables sending of ICMP Destination Unreachable Error on specific interface.

OBJECT-TYPE

The maximum transmission unit (MTU) size of IPv6 packets sent on an interface in bytes.

OBJECT-TYPE

Set version of MLD protocol on specific interface.

OBJECT-TYPE

This value will be included in all IPv6 router advertisements sent out this interface. Very short intervals are not recommended in normal IPv6 operation. When a nondefault value is configured, the configured time is both advertised and used by the router itself. When value 0 is configured, 0 seconds (unspecified) advertised in router advertisements and the value 1000 milliseconds is used for the neighbor discovery activity of the router itself.

OBJECT-TYPE

Enables or disables sending of ICMP IPv6 redirect messages to re-send a packet through the same interface on which the packet was received.

OBJECT-TYPE

This table is parallel to inetCidrRouteTable, and is used to configure or display additional route parameters.

OBJECT-TYPE

Additional parameters for a particular route.

OBJECT-TYPE

The remaining length of time, in seconds, that this route will continue to be valid, i.e., time until deprecation. A value of 4,294,967,295 represents infinity.

OBJECT-TYPE

A reference to MIB definitions specific to the particular routing protocol which is responsible for this route, as determined by the value specified in the route's inetCidrRouteProto value.

OBJECT-TYPE

This table is parallel to ipNetToPhysicalTable, and is used to configure or display additional neighbor parameters.

OBJECT-TYPE

Additional parameters for a neighbor

OBJECT-TYPE

This object has the value 'true(1)', if the neighbor is router; otherwise, the value is 'false(2)'.

OBJECT-TYPE

Time (in seconds) since the address was confirmed to be reachable. Only, relevant for dynamic entries.

OBJECT-TYPE

This entity's static (user configured) Inet Routing table. Entries are MAX-ACCESSible even if not used for forwarding

OBJECT-TYPE

A particular Static(user configured) route to a particular destination.

OBJECT-TYPE

The type of the address used as the destination internetwork address or subnet address.

OBJECT-TYPE

Destination internetwork address or subnet address. The destination prefix length is applied to this value, and to a particular destination address, to determine whether the route applies to the particular address. If the prefix length is L, then applying the length to an address means taking the first L bits of the address.

OBJECT-TYPE

Indicates the number of leading one bits that form the mask to be logical-ANDed with the destination address before being compared to the value in the rlInetStaticRouteDest field.

OBJECT-TYPE

The type of the address used as the next-hop address for this route.

OBJECT-TYPE

The next-hop IP address, if any. If rlInetStaticRouteAction is 'forward', there may or may not be a next-hop IP address. A next-hop IP address is not required if an output interface index is specified (in other words, if rlInetStaticRouteIfIndex is non-zero). If rlInetStaticRouteAction is not 'forward', there is no next-hop IP address. If there is no next-hop IP address, the rlInetStaticRouteNextHop object is set to all zeroes.

OBJECT-TYPE

The ifIndex value that identifies the local interface through which the next hop of this route should be reached. A value of 0 is valid and represents the scenario where no interface is specified.

OBJECT-TYPE

Path cost for this static route.

OBJECT-TYPE

Same as inetCidrRouteType MIB (excluded 'other' route type)

OBJECT-TYPE

Static - The route is configured over Static IP. This route is written to configuration files. Dhcp - The route is Configured by DHCP (received as part of DHCP configuration) This route IS NOT written to configuration files Default - The route is Configured by default system config exists till any other configuration is applied. Icmp - The route is Configured by ICMP protocol either by router advertisements or to be advertised in router advertisements .

OBJECT-TYPE

The row status variable, used according to row installation and removal conventions. A row entry cannot be modified when the status is marked as active(1).

OBJECT-TYPE

active - An indication that the route has implication on routing inactive - the route is a backup route or it is down. It is not used in forwarding decision. Down means that the Ip interface on which it is configured is down. (Note: ip interface down may be for two reason - its admin status or the L2 interface , on which the ip interface is configured, status

OBJECT-TYPE

Track object number

OBJECT-TYPE

Track status

OBJECT-TYPE

This table defines administrative distances for different protocol routes that are inserted into the routing table.

OBJECT-TYPE

A set of distances per inet address type.

OBJECT-TYPE

The inet address type for distance definitions set, either IPv4 or IPv6.

OBJECT-TYPE

The administrative distance used for directly connected routes.

OBJECT-TYPE

The administrative distance used for static routes.

OBJECT-TYPE

The administrative distance used for RIP routes.

OBJECT-TYPE

The administrative distance used for OSPF internal routes.

OBJECT-TYPE

The administrative distance used for OSPF Autonomous System external routes.

OBJECT-TYPE

Internal inetCidrRouteTable - this entity's IP Routing table.

OBJECT-TYPE

A particular route to a particular destination, under a particular policy (as reflected in the rlInternInetCidrRoutePolicy object). Dynamically created rows will survive an agent reboot. Implementers need to be aware that if the total number of elements (octets or sub-identifiers) in rlInternInetCidrRouteDest, rlInternInetCidrRoutePolicy, and rlInternInetCidrRouteNextHop exceeds 111, then OIDs of column instances in this table will have more than 128 sub- identifiers and cannot be accessed using SNMPv1, SNMPv2c, or SNMPv3.

OBJECT-TYPE

The type of the rlInternInetCidrRouteDest address, as defined in the InetAddress MIB. Only those address types that may appear in an actual routing table are allowed as values of this object.

OBJECT-TYPE

The destination IP address of this route. The type of this address is determined by the value of the rlInternInetCidrRouteDestType object. The values for the index objects rlInternInetCidrRouteDest and rlInternInetCidrRoutePfxLen must be consistent. When the value of rlInternInetCidrRouteDest (excluding the zone index, if one is present) is x, then the bitwise logical-AND of x with the value of the mask formed from the corresponding index object rlInternInetCidrRoutePfxLen MUST be equal to x. If not, then the index pair is not consistent and an inconsistentName error must be returned on SET or CREATE requests.

OBJECT-TYPE

Indicates the number of leading one bits that form the mask to be logical-ANDed with the destination address before being compared to the value in the rlInternInetCidrRouteDest field. The values for the index objects rlInternInetCidrRouteDest and rlInternInetCidrRoutePfxLen must be consistent. When the value of rlInternInetCidrRouteDest (excluding the zone index, if one is present) is x, then the bitwise logical-AND of x with the value of the mask formed from the corresponding index object rlInternInetCidrRoutePfxLen MUST be equal to x. If not, then the index pair is not consistent and an inconsistentName error must be returned on SET or CREATE requests.

OBJECT-TYPE

This object is an opaque object without any defined semantics. Its purpose is to serve as an additional index that may delineate between multiple entries to the same destination. The value { 0 0 } shall be used as the default value for this object.

OBJECT-TYPE

The type of the rlInternInetCidrRouteNextHop address, as defined in the InetAddress MIB. Value should be set to unknown(0) for non-remote routes. Only those address types that may appear in an actual routing table are allowed as values of this object.

OBJECT-TYPE

On remote routes, the address of the next system en route. For non-remote routes, a zero length string. The type of this address is determined by the value of the rlInternInetCidrRouteNextHopType object.

OBJECT-TYPE

The ifIndex value that identifies the local interface through which the next hop of this route should be reached. A value of 0 is valid and represents the scenario where no interface is specified.

OBJECT-TYPE

The type of route. Note that local(3) refers to a route for which the next hop is the final destination; remote(4) refers to a route for which the next hop is not the final destination. Routes that do not result in traffic forwarding or rejection should not be displayed, even if the implementation keeps them stored internally. reject(2) refers to a route that, if matched, discards the message as unreachable and returns a notification (e.g., ICMP error) to the message sender. This is used in some protocols as a means of correctly aggregating routes. blackhole(5) refers to a route that, if matched, discards the message silently.

OBJECT-TYPE

The routing mechanism via which this route was learned. Inclusion of values for gateway routing protocols is not intended to imply that hosts should support those protocols.

OBJECT-TYPE

The number of seconds since this route was last updated or otherwise determined to be correct. Note that no semantics of 'too old' can be implied, except through knowledge of the routing protocol by which the route was learned.

OBJECT-TYPE

The Autonomous System Number of the Next Hop. The semantics of this object are determined by the routing- protocol specified in the route's rlInternInetCidrRouteProto value. When this object is unknown or not relevant, its value should be set to zero.

OBJECT-TYPE

The primary routing metric for this route. The semantics of this metric are determined by the routing- protocol specified in the route's rlInternInetCidrRouteProto value. If this metric is not used, its value should be set to -1.

OBJECT-TYPE

An alternate routing metric for this route. The semantics of this metric are determined by the routing- protocol specified in the route's rlInternInetCidrRouteProto value. If this metric is not used, its value should be set to -1.

OBJECT-TYPE

An alternate routing metric for this route. The semantics of this metric are determined by the routing- protocol specified in the route's rlInternInetCidrRouteProto value. If this metric is not used, its value should be set to -1.

OBJECT-TYPE

An alternate routing metric for this route. The semantics of this metric are determined by the routing- protocol specified in the route's rlInternInetCidrRouteProto value. If this metric is not used, its value should be set to -1.

OBJECT-TYPE

An alternate routing metric for this route. The semantics of this metric are determined by the routing- protocol specified in the route's rlInternInetCidrRouteProto value. If this metric is not used, its value should be set to -1.

OBJECT-TYPE

The row status variable, used according to row installation and removal conventions. A row entry cannot be modified when the status is marked as active(1).

OBJECT-TYPE

The remaining length of time, in seconds, that this route will continue to be valid, i.e., time until deprecation. A value of 4,294,967,295 represents infinity.

OBJECT-TYPE

A reference to MIB definitions specific to the particular routing protocol which is responsible for this route, as determined by the value specified in the route's inetCidrRouteProto value.

OBJECT-TYPE

This entity's static (user configured) Inet Routing table. Entries are MAX-ACCESSible even if not used for forwarding

OBJECT-TYPE

A particular Static(user configured) route to a particular destination.

OBJECT-TYPE

The type of the address used as the destination internetwork address or subnet address.

OBJECT-TYPE

Destination internetwork address or subnet address. The destination prefix length is applied to this value, and to a particular destination address, to determine whether the route applies to the particular address. If the prefix length is L, then applying the length to an address means taking the first L bits of the address.

OBJECT-TYPE

Indicates the number of leading one bits that form the mask to be logical-ANDed with the destination address before being compared to the value in the rlInternInetStaticRouteDest field.

OBJECT-TYPE

The type of the address used as the next-hop address for this route.

OBJECT-TYPE

The next-hop IP address, if any. If rlInternInetStaticRouteAction is 'forward', there may or may not be a next-hop IP address. A next-hop IP address is not required if an output interface index is specified (in other words, if rlInternInetStaticRouteIfIndex is non-zero). If rlInternInetStaticRouteAction is not 'forward', there is no next-hop IP address. If there is no next-hop IP address, the rlInternInetStaticRouteNextHop object is set to all zeroes.

OBJECT-TYPE

The ifIndex value that identifies the local interface through which the next hop of this route should be reached. A value of 0 is valid and represents the scenario where no interface is specified.

OBJECT-TYPE

Path cost for this static route. Value of 0 signs default value metric

OBJECT-TYPE

Same as inetCidrRouteType MIB (excluded 'other' route type)

OBJECT-TYPE

Static - The route is configured over Static IP. This route is written to configuration files. Dhcp - The route is Configured by DHCP (received as part of DHCP configuration) This route IS NOT written to configuration files Default - The route is Configured by default system config exists till any other configuration is applied. Icmp - The route is Configured by ICMP protocol either by router advertisements or to be advertised in router advertisements .

OBJECT-TYPE

The row status variable, used according to row installation and removal conventions. A row entry cannot be modified when the status is marked as active(1).

OBJECT-TYPE

active - An indication that the route has implication on routing inactive - the route is a backup route or it is down. It is not used in forwarding decision. Down means that the Ip interface on which it is configured is down.

OBJECT-TYPE

The time interval between tokens being placed in the bucket, each token represents a single ICMP error message. The interval measured in milliseconds.

OBJECT-TYPE

The maximum number of tokens stored in the bucket, each token represents a single ICMP error message.

OBJECT-TYPE

The interface which would be used as the egress interface for packets sent without a specified IPv6Z interface identifier or with the default '0' identifier. Zero value means no default interface specified.

OBJECT-TYPE

This table defines general prefix description, based on which a number of longer, more specific, prefixes can be defined.

OBJECT-TYPE

Single entry in general prefix table.

OBJECT-TYPE

The name assigned to the prefix.

OBJECT-TYPE

Prefix inet address type. Has to be IPv6.

OBJECT-TYPE

The IPv6 network assigned to the general prefix. This argument must be in the form documented in RFC4293 where the address is specified in hexadecimal using 16-bit values between colons.

OBJECT-TYPE

Indicates the number of leading one bits that form the mask to be logical-ANDed with the inet address before being compared to the value in the rlIpv6GeneralPrefixInetAddr field.

OBJECT-TYPE

Interface id to use when creating prefix based on point-to-point interface.

OBJECT-TYPE

Row status.

OBJECT-TYPE

Maximum number of hops used in router advertisements and all IPv6 packets that are originated by the router.

OBJECT-TYPE

This table defines IPv6 prefixes which are included in IPv6 Neighbor Discovery (ND) router advertisements.

OBJECT-TYPE

Single entry in Neighbor Discovery Prefix table.

OBJECT-TYPE

The index value that uniquely identifies the interface on which this prefix is configured. The interface identified by a particular value of this index is the same interface as identified by the same value of the IF-MIB's ifIndex.

OBJECT-TYPE

Indicates whether this object belongs to 'default' entry. Default entry contains specifics about advertising prefixes which were created from local ipv6 addresses.

OBJECT-TYPE

Prefix inet address type. Has to be IPv6.

OBJECT-TYPE

The IPv6 network prefix to include in router advertisements. This argument must be in the form documented in RFC4293 where the address is specified in hexadecimal using 16-bit values between colons.

OBJECT-TYPE

The length of the IPv6 prefix. A decimal value that indicates how many of the high-order contiguous bits of the address comprise the prefix (the network portion of the address).

OBJECT-TYPE

Admin status of the entry. Relevant only for default entry.

OBJECT-TYPE

Whether the prefix is included in router advertisements.

OBJECT-TYPE

If object has the value 'onlink(1)', this prefix is confidered as on-link. This prefix will be advertised with the L-bit set and will be present in the Routing Table. If object has the value 'not-onlink(2)', this prefix will be advertised with the L-bit clear, but connected state of the prefix will not be changed. If object has the value 'offlink(3)', this prefix is confidered as on-link. This prefix will be advertised with the L-bit clear, and will be not present in the Routing Table.

OBJECT-TYPE

If object has the value 'true(1)', this prefix indicates to hosts on the local link that the specified prefix can be used for IPv6 autoconfiguration. The prefix will be advertised with the A-bit set.

OBJECT-TYPE

The amount of time (in seconds) that the specified IPv6 prefix is advertised as being preferred.

OBJECT-TYPE

The amount of time (in seconds) that the specified IPv6 prefix is advertised as being valid.

OBJECT-TYPE

Row status.

OBJECT-TYPE

This table is parallel to inetCidrRouteTable, and is used to configure or display additional route parameters.

OBJECT-TYPE

Additional parameters for a particular route.

OBJECT-TYPE

Indicates to a visiting mobile node the interval at which that node may expect to receive RAs. The node may use this information in its movement detection algorithm.

OBJECT-TYPE

Configures a default router preference (DRP) for the router on a specific interface.

OBJECT-TYPE

Indicates that hop limit value used in router advertisement is an user configured value and not necessarily value that is used by router itself.

OBJECT-TYPE

This scalar indicates to clear all ipv6 routes from inetCidrTable.

OBJECT-TYPE

This table used to represent all Path MTU changes to specific destination received from 'packet-too-big' messages.

OBJECT-TYPE

Single entry in Path MTU table.

OBJECT-TYPE

Prefix inet address type. Has to be IPv6.

OBJECT-TYPE

The IPv6 destination address for which packet-too-big message was received. This argument must be in the form documented in RFC4293 where the address is specified in hexadecimal using 16-bit values between colons.

OBJECT-TYPE

The MTU value that was received in packet-too-bug message for specific destination.

OBJECT-TYPE

This entry's age (seconds)

OBJECT-TYPE

This entity is used to clear all or specific-type entries from ipNetToPhysicalTable.

OBJECT-TYPE

A particular entry in this table.

OBJECT-TYPE

Interface index of to clear or zero in case of whole table.

OBJECT-TYPE

Scope of the action - type of entries to delete.

OBJECT-TYPE

This entity's IPv6 host forwarding table.

OBJECT-TYPE

A particular Static(user configured) route to a particular destination.

OBJECT-TYPE

The type of the address used as the destination internetwork address or subnet address.

OBJECT-TYPE

Destination internetwork address or subnet address.

OBJECT-TYPE

Indicates the number of leading one bits that form the mask to be logical-ANDed with the destination address before being compared to the value in the rlIpv6HostForwardingDest field.

OBJECT-TYPE

The type of the address used as the next-hop address for this route.

OBJECT-TYPE

The next-hop IP address, if any. A next-hop IP address is not required if an output interface index is specified (in other words, if rlIpv6HostForwardingIfIndex is non-zero). If there is no next-hop IP address, the rlIpv6HostForwardingNextHop object is set to all zeroes.

OBJECT-TYPE

The ifIndex value that identifies the local interface through which the next hop of this route should be reached. A value of 0 is valid and represents the scenario where no interface is specified.

OBJECT-TYPE

Forwarding type

OBJECT-TYPE

Path cost for this route.

OBJECT-TYPE

the MIB is relevant when mtsc parameter DHCPv6_client_enabled_by_default is TRUE. If the MIB has non zero value the meaning is that ipv6 interface has removed from configuration by the user on the interface and signs to application not to add ipv6 interface. Otherwise (zero value) - the meaning is that Ipv6 interface must be added.

OBJECT-TYPE

The system management IPv6 address which is kept between system mode changes

OBJECT-TYPE

The system management IPv6 action: clear - delete all ipv6 interfaces from startup configuration database except rlManagementIpv6

OBJECT-TYPE

This entity's IPv6 Tunnel if/addr/prefix table.

OBJECT-TYPE

A particular tunnel configured data to IPv6 db.

OBJECT-TYPE

IfIndex of tunnel interface

OBJECT-TYPE

Action of the entry. All other fields relevant for appropriate actions.

OBJECT-TYPE

Tunnel type (manual/isatap/6to4/...).

OBJECT-TYPE

The address used for this tunnel. Could be local IPv4 of the tunnel.

OBJECT-TYPE

The address/prefix length used for above address if applicable.

OBJECT-TYPE

Mtu of this interface. Used for host isatap tunnels

OBJECT-TYPE

Minimal router solicitation interval. Used for host isatap tunnels

OBJECT-TYPE

IPv4 address used for link-layer of ipv6 over ipv4 tunnel

OBJECT-TYPE

The default value inserted into the TC field of the IPv6 header of datagrams originated at this entity, whenever a TC value is not supplied by the application.

OBJECT-TYPE

The default value inserted into the User Priority field in the 802.1q VLAN tag of IPv4 frames sent by the CPU.

OBJECT-TYPE

Sets the maximum transmission unit (MTU) size in bytes of IPv6 packets (payload).

OBJECT-TYPE

This entity's IPv6 auxulary mapping table. Serves to map nexthop ipv6 address to on-link prefix ifindex

OBJECT-TYPE

An Auxulary Mapping table to find onlink prefix ifindex for ipv6 static route.

OBJECT-TYPE

The type of the address used as the next-hop address for this route.

OBJECT-TYPE

The next-hop IP address

OBJECT-TYPE

The ifIndex mapped to specified necthop address