CISCO-WIRELESS-EXP-MIB
- Registered at
- 1.3.6.1.4.1.9.10.52
- Last updated
- 2005-12-27 10:03
- Organization
- Cisco Systems Inc.
- Revisions
- 2005-12-27 10:03, 1999-05-13 20:10
- Namespace
- cisco
- Source file
CISCO-WIRELESS-EXP-MIB- Digest
sha256:dd987682c57d23190c66da9840edba72bff460ade04ba3776ba16cb0fb0b1eba
Description
This is the MIB Module for the Cisco Wireless Radio Point to Point experimental components. Glossary The following terms are used in the MIB definitions below. Radio Card: The line card that provides the wireless communication features. Radio Link: The bi-directional wireless link that exists between two communicating radio cards. Radio PHY: Represents the transmission characteristics of the Radio Link. RF Unit: The Radio Frequency components and the associated antennas. Radio System: Radio card and RF unit(s). Cisco Wireless Radio Experimental MIB Organization The Cisco Wireless Radio Experimental MIB provides the following management groups : When the draft-ietf-entmib-v2-03.txt gets finalized the Radio Frequency Group will be moved into that MIB. When the CISCO-IMAGE-MIB.my gets updated to include the image capabilities, the Image Group will be migrated into that MIB. When the CISCO-LED-MIB.my becomes available and supports the functionality the LED group needs, the LED group will be migrated into that. o. Radio Frequency Resource Group This contains information about the Radio frequency transmission and reception resources available on the system. This group determines the portions of the radio spectrum at which the radio subsystem can operate. This group in conjunction with the radio PHY group determine the acutal spectrum that gets used for communications. o. Image Group This provides facilities to manage radio line card's firmware image file URL's in router's image repository. It also provides access to the image details. o. LED Group This group provides information about LEDs available on the line card. o. Duplexor Group This group provides information about the Duplexors installed in the RF resources.
Contact
Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: firestar-sw@cisco.com
Imports
| From | Symbols |
|---|---|
| CISCO-SMI | ciscoExperiment |
| ENTITY-MIB | entPhysicalIndex |
| IF-MIB | ifIndex |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP |
| SNMPv2-SMI | Integer32, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, Unsigned32, iso |
| SNMPv2-TC | DateAndTime, DisplayString, TEXTUAL-CONVENTION |
Imported by
Nothing in this corpus imports this module.
Load order
Every file a consumer needs in order to load this module, dependencies first.
CISCO-SMI CISCO-WIRELESS-EXP-MIB ENTITY-MIB IANA-ENTITY-MIB IANAifType-MIB IF-MIB SNMP-FRAMEWORK-MIB SNMPv2-CONF SNMPv2-MIB SNMPv2-SMI SNMPv2-TC UUID-TC-MIB
Objects
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| cwrRadioExpMibObjects OBJECT-IDENTITY | 1.3.6.1.4.1.9.10.52.1 | |||
| cwrRadioFreqEntityGroup OBJECT-IDENTITY | 1.3.6.1.4.1.9.10.52.1.1 | |||
| cwrRfEntityTable OBJECT-TYPE This table contains information about the radio frequency resources available for use on the system. | 1.3.6.1.4.1.9.10.52.1.1.1 | not-accessible | current | |
| cwrRfEntityEntry OBJECT-TYPE This represents one entry in the cwrRfEntityTable. This table is largely a read only table which provides details on the radio frequency resources available on the system. Physically each RF resource may be realized by one antenna and its associated control hardware. But a single antenna and its associated hardware may act as more than 1 RF resource. A Duplexor is a mechanical device, that acts as a band pass filter when installed in an RF resource. Normally a RF resource is capable of operating over a wide frequency range. To operate at restricted frequencies, the user has to own that part of the frequency spectrum. Since the user may not own parts of the frequency spectrum over which the RF resource may operate, a Duplexor is installed in the RF resource. This restricts the RF resource to operate in the passband defined by the Duplexor. In this table the Duplexor's are identified by an index into the cwrDuplexorTable. It is indexed by the ifIndex and cwrRfEntityIndex. | 1.3.6.1.4.1.9.10.52.1.1.1.1 | not-accessible | current | |
| cwrRfEntityIndex OBJECT-TYPE This object represents the index of this entry in the cwrRfEntityTable. | 1.3.6.1.4.1.9.10.52.1.1.1.1.1 | Integer32 (1..2147483647) | not-accessible | current |
| cwrRfSwRevision OBJECT-TYPE This object represents the software revision number of controlling the RF subsystem. | 1.3.6.1.4.1.9.10.52.1.1.1.1.2 | Unsigned32 | read-only | current |
| cwrRfAssemblyPartNumberClass OBJECT-TYPE This object represents the assembly part number class of the RF subsystem. | 1.3.6.1.4.1.9.10.52.1.1.1.1.3 | Unsigned32 | read-only | current |
| cwrRfAssemblyPartNumberBase OBJECT-TYPE This object represents the assembly part number base of the RF subsystem. | 1.3.6.1.4.1.9.10.52.1.1.1.1.4 | Unsigned32 | read-only | current |
| cwrRfAssemblyPartNumberVersion OBJECT-TYPE This object represents the assembly part number version of the RF subsystem. | 1.3.6.1.4.1.9.10.52.1.1.1.1.5 | Unsigned32 | read-only | current |
| cwrRfBoardPartNumberClass OBJECT-TYPE This object represents the board part number class of the RF subsystem. | 1.3.6.1.4.1.9.10.52.1.1.1.1.6 | Unsigned32 | read-only | current |
| cwrRfBoardPartNumberBase OBJECT-TYPE This object represents the board part number base of the RF subsystem. | 1.3.6.1.4.1.9.10.52.1.1.1.1.7 | Unsigned32 | read-only | current |
| cwrRfBoardPartNumberVersion OBJECT-TYPE This object represents the board part number version of the RF subsystem. | 1.3.6.1.4.1.9.10.52.1.1.1.1.8 | Unsigned32 | read-only | current |
| cwrRfBoardRevision OBJECT-TYPE This object represents the board revision of the RF subsystem. | 1.3.6.1.4.1.9.10.52.1.1.1.1.9 | DisplayString | read-only | current |
| cwrRfSerialNumber OBJECT-TYPE This object represents the serial number of the RF subsystem. | 1.3.6.1.4.1.9.10.52.1.1.1.1.10 | DisplayString | read-only | current |
| cwrRfManfDate OBJECT-TYPE This object represents the manufacturing date of the RF subsystem. | 1.3.6.1.4.1.9.10.52.1.1.1.1.11 | DateAndTime | read-only | current |
| cwrRfVendorId OBJECT-TYPE This object represents the Radio frequency device vendor ID. | 1.3.6.1.4.1.9.10.52.1.1.1.1.12 | Integer32 (1..256) | read-only | current |
| cwrRfDuplexorIndex OBJECT-TYPE This object represents the index into cwrDuplexorTable. This index identifies the Duplexor associated with this RF resource. | 1.3.6.1.4.1.9.10.52.1.1.1.1.13 | Integer32 (1..2147483647) | read-only | current |
| cwrIntFreqEntityTable OBJECT-TYPE This table contains information about the intermediate frequency subsystem on the radio card. | 1.3.6.1.4.1.9.10.52.1.1.2 | not-accessible | current | |
| cwrIntFreqEntityEntry OBJECT-TYPE This represents one entry in the cwrIntFreqEntityTable. This table is largely a read only table which provides details on the intermediate frequency subsystem available on the radio card. It is indexed by the ifIndex. | 1.3.6.1.4.1.9.10.52.1.1.2.1 | not-accessible | current | |
| cwrIfAssemblyPartNumberClass OBJECT-TYPE This object represents the assembly part number class of the IF subsystem. | 1.3.6.1.4.1.9.10.52.1.1.2.1.1 | Unsigned32 | read-only | current |
| cwrIfAssemblyPartNumberBase OBJECT-TYPE This object represents the assembly part number base of the IF subsystem. | 1.3.6.1.4.1.9.10.52.1.1.2.1.2 | Unsigned32 | read-only | current |
| cwrIfAssemblyPartNumberVersion OBJECT-TYPE This object represents the assembly part number version of the IF subsystem. | 1.3.6.1.4.1.9.10.52.1.1.2.1.3 | Unsigned32 | read-only | current |
| cwrIfBoardPartNumberClass OBJECT-TYPE This object represents the board part number class of the IF subsystem. | 1.3.6.1.4.1.9.10.52.1.1.2.1.4 | Unsigned32 | read-only | current |
| cwrIfBoardPartNumberBase OBJECT-TYPE This object represents the board part number base of the IF subsystem. | 1.3.6.1.4.1.9.10.52.1.1.2.1.5 | Unsigned32 | read-only | current |
| cwrIfBoardPartNumberVersion OBJECT-TYPE This object represents the board part number version of the IF subsystem. | 1.3.6.1.4.1.9.10.52.1.1.2.1.6 | Unsigned32 | read-only | current |
| cwrIfBoardRevision OBJECT-TYPE This object represents the board revision of the IF subsystem. | 1.3.6.1.4.1.9.10.52.1.1.2.1.7 | DisplayString | read-only | current |
| cwrIfSerialNumber OBJECT-TYPE This object represents the serial number of the IF subsystem. | 1.3.6.1.4.1.9.10.52.1.1.2.1.8 | DisplayString | read-only | current |
| cwrIfManfDate OBJECT-TYPE This object represents the manufacturing date of the IF subsystem. | 1.3.6.1.4.1.9.10.52.1.1.2.1.9 | DateAndTime | read-only | current |
| cwrIfVendorId OBJECT-TYPE This object represents the IF vendor ID. | 1.3.6.1.4.1.9.10.52.1.1.2.1.10 | Integer32 (1..256) | read-only | current |
| cwrIfSwRevision OBJECT-TYPE This object represents the IF software revision. | 1.3.6.1.4.1.9.10.52.1.1.2.1.11 | Unsigned32 | read-only | current |
| cwrRadioImageGroup OBJECT-IDENTITY | 1.3.6.1.4.1.9.10.52.1.2 | |||
| cwrImageTable OBJECT-TYPE This table provides facilities to manage the firmware images that the router will use to configure the radio line cards. When images need to be downloaded, the software will search this list starting from the first, for an image whose capabilities match the configuration specified in the cwrRadioBaseTable and the cwrRadioPhyTable and download that image to the appropriate hardware component. Insertion into the table at arbitrary points is not supported. Any new image URL added to this table will be inserted at index 1 only. Also note that an image gets downloaded to the hardware only when when a radio link is administratively enabled. | 1.3.6.1.4.1.9.10.52.1.2.1 | not-accessible | current | |
| cwrImageEntry OBJECT-TYPE This represents one entry in the cwrImageTable. | 1.3.6.1.4.1.9.10.52.1.2.1.1 | not-accessible | current | |
| cwrImageIndex OBJECT-TYPE This represents the one entry in this table. It also represents the search order. When images need to be downloaded to the hardware, the images are searched in the order of this index for an image that matches the hardware capabilities and uses it. | 1.3.6.1.4.1.9.10.52.1.2.1.1.1 | Integer32 (1..2147483647) | not-accessible | current |
| cwrImageNameUrl OBJECT-TYPE This object is the name of the image in the Universal Resource Locator (URL) format. This URL will be used to access the image when needed. | 1.3.6.1.4.1.9.10.52.1.2.1.1.2 | DisplayString (SIZE(1..255)) | read-write | current |
| cwrImageState OBJECT-TYPE This represents the state of the image. image_invalid(1): If the image could not be accessed for any reason. image_valid(2) : Image accessible and available for use. | 1.3.6.1.4.1.9.10.52.1.2.1.1.3 | INTEGER {imageInvalid(1), imageValid(2)} | read-only | current |
| cwrImageSize OBJECT-TYPE This represents the size of the image in bytes. | 1.3.6.1.4.1.9.10.52.1.2.1.1.4 | Unsigned32 | read-only | current |
| cwrImageChipClass OBJECT-TYPE This represents the class of chips onto which this image may be loaded. | 1.3.6.1.4.1.9.10.52.1.2.1.1.5 | Unsigned32 | read-only | current |
| cwrImageChipType OBJECT-TYPE This represents the download method to use. | 1.3.6.1.4.1.9.10.52.1.2.1.1.6 | Unsigned32 | read-only | current |
| cwrImageCapability1 OBJECT-TYPE This represents a bitmask. The bit mask identifies the capabilities of this image. See also cwrImageCapability2. | 1.3.6.1.4.1.9.10.52.1.2.1.1.7 | Unsigned32 | read-only | current |
| cwrImageCapability2 OBJECT-TYPE This represents a bitmask. The bit mask identifies the capabilities of this image in addition to cwrImageCapability1. | 1.3.6.1.4.1.9.10.52.1.2.1.1.8 | Unsigned32 | read-only | current |
| cwrImageVersion OBJECT-TYPE This represents the version number of this image. | 1.3.6.1.4.1.9.10.52.1.2.1.1.9 | Unsigned32 | read-only | current |
| cwrImageTag OBJECT-TYPE This object is the tag string associated with the image. Normally used to trace the source code used to generate this image. | 1.3.6.1.4.1.9.10.52.1.2.1.1.10 | DisplayString (SIZE(1..255)) | read-only | current |
| cwrImageOp OBJECT-TYPE This object represents the operation to be performed on the identified image. nop(0) - This value will be returned when this object is read. add(1) - Will add the image URL, as the first entry in the image table. delete(2) - Will delete the specified ULR from the image table. move(3) - Will make the image specified by the URL the first entry in the imageTable. | 1.3.6.1.4.1.9.10.52.1.2.1.1.11 | INTEGER {nop(0), add(1), delete(2), move(3)} | read-write | current |
| cwrRadioLedGroup OBJECT-IDENTITY | 1.3.6.1.4.1.9.10.52.1.3 | |||
| cwrLedTable OBJECT-TYPE Entity (Light emitting diode) LED information. For each LED on the entity, an entry will exist in this table, describing the location and current status of that LED. | 1.3.6.1.4.1.9.10.52.1.3.1 | not-accessible | current | |
| cwrLedEntry OBJECT-TYPE An entry in the table, containing the LED information about the entity. The entPhysicalIndex identifies the entity on which the Led's are present. | 1.3.6.1.4.1.9.10.52.1.3.1.1 | not-accessible | current | |
| cwrLedIndex OBJECT-TYPE For a given entPhysicalIndex, this index value uniquely identifies an entry in the cwrLedTable. | 1.3.6.1.4.1.9.10.52.1.3.1.1.1 | INTEGER (1..16) | not-accessible | current |
| cwrLedName OBJECT-TYPE The label of the LED on the physical entity or a textual description to identify the usage of the LED. | 1.3.6.1.4.1.9.10.52.1.3.1.1.2 | DisplayString | read-only | current |
| cwrLedVerticalPosition OBJECT-TYPE The position of the LED in the entity. It is counted from top to bottom. | 1.3.6.1.4.1.9.10.52.1.3.1.1.3 | Integer32 (1..16) | read-only | current |
| cwrLedHorizontalPosition OBJECT-TYPE The position of the LED in the entity. It is counted from from left to right. | 1.3.6.1.4.1.9.10.52.1.3.1.1.4 | Integer32 (1..16) | read-only | current |
| cwrLedMode OBJECT-TYPE This objects specifies the desired mode of LED updates. automatic(1) and latched(2) are settings used by the software to determine how the LED should be updated. The others are for diagnostic purposes. The LED will be turned on or off as specified by the other (3-8) settings. The modes mean the following: automatic(1): The system updates the LED according to the default settings for that entity. latched(2): Once the LED is turned on, user has to turn it off. This applies only to alarm LEDs. forceOff(3): Force the LED off. forceSolidGreen(4): Force the LED to be solid green in on state. forceSolidYellow(5):Force the LED to be solid Yellow in on state forceBlinkGreen(6): Force the LED to blink in Green. forceBlinkYellow(7):Force the LED to blink in Yellow. forceBlinkBoth(8): Force the LED to blink Yellow and Green alternatively. | 1.3.6.1.4.1.9.10.52.1.3.1.1.5 | INTEGER {automatic(1), latched(2), forceOff(3), forceSolidGreen(4), forceSolidYellow(5), forceBlinkGreen(6), forceBlinkYellow(7), forceBlinkBoth(8)} | read-write | current |
| cwrLedCurrentColor OBJECT-TYPE Indicates the current color of the LED. | 1.3.6.1.4.1.9.10.52.1.3.1.1.6 | INTEGER {green(1), yellow(2), blinkGreen(3), blinkYellow(4), blinkGreenYellow(5), off(6)} | read-only | current |
| cwrRadioDuplexorGroup OBJECT-IDENTITY | 1.3.6.1.4.1.9.10.52.1.4 | |||
| cwrDuplexorTable OBJECT-TYPE This table contains information about the Duplexors available for use on the system. | 1.3.6.1.4.1.9.10.52.1.4.1 | not-accessible | current | |
| cwrDuplexorEntry OBJECT-TYPE This represents one entry in the cwrDuplexorTable. This table provides details on the Duplexors available on the system. It is indexed by the ifIndex and cwrDuplexorIndex. | 1.3.6.1.4.1.9.10.52.1.4.1.1 | not-accessible | current | |
| cwrDuplexorIndex OBJECT-TYPE This object represents the index of this entry in the cwrDuplexorTable. | 1.3.6.1.4.1.9.10.52.1.4.1.1.1 | Integer32 (1..2147483647) | not-accessible | current |
| cwrDuplexorCiscoPartNumber OBJECT-TYPE This object represents the Cisco part number for this Duplexor. | 1.3.6.1.4.1.9.10.52.1.4.1.1.2 | DisplayString | read-write | current |
| cwrDuplexorLoPassbandRange OBJECT-TYPE This object represents the low frequency range that this Duplexor will pass through without any attenuation. All low frequencies outside this range will be attenuated to a level such that an RF resource that uses this Duplexor will be unable to transmit or receive those frequencies. | 1.3.6.1.4.1.9.10.52.1.4.1.1.3 | DisplayString | read-write | current |
| cwrDuplexorHiPassbandRange OBJECT-TYPE This object represents the high frequency range that this Duplexor will pass through without any attenuation. All high frequencies outside this range will be attenuated to a level such that an RF resource that uses this Duplexor will be unable to transmit or receive those frequencies. | 1.3.6.1.4.1.9.10.52.1.4.1.1.4 | DisplayString | read-write | current |
| cwrDuplexorReceivePassband OBJECT-TYPE This object indicates which of the two passbands are being used to receive transmissions. The RF Resource can receive on either of the duplexor passbands. loPassband(1) - The RF Resource is receiving on a frequency within the range identified by cwrDuplexorLoPassbandRange. hiPassband(2) - The RF Resource is receiving on a frequency within the range identified by cwrDuplexorHiPassbandRange. | 1.3.6.1.4.1.9.10.52.1.4.1.1.5 | INTEGER {loPassband(1), hiPassband(2)} | read-write | current |
| cwrDuplexorCLEICode OBJECT-TYPE The CLEI code for this Duplexor. | 1.3.6.1.4.1.9.10.52.1.4.1.1.6 | DisplayString | read-write | current |
| cwrDuplexorVendorName OBJECT-TYPE The Vendor Name for this Duplexor. | 1.3.6.1.4.1.9.10.52.1.4.1.1.7 | DisplayString | read-write | current |
| cwrDuplexorSerialNumber OBJECT-TYPE The Serial number of this Duplexor. | 1.3.6.1.4.1.9.10.52.1.4.1.1.8 | DisplayString | read-write | current |
| cwrRadioExpConformance OBJECT-IDENTITY | 1.3.6.1.4.1.9.10.52.2 | |||
| cwrRadioExpCompliances OBJECT-IDENTITY | 1.3.6.1.4.1.9.10.52.2.1 | |||
| cwrRadioExpGroups OBJECT-IDENTITY | 1.3.6.1.4.1.9.10.52.2.2 |
Conformance
| Name | OID | Status |
|---|---|---|
| cwrRadioExpCompliance MODULE-COMPLIANCE The compliance statement for Point to Point wireless interface devices compliant to Cisco Systems Inc. specification. | 1.3.6.1.4.1.9.10.52.2.1.1 | current |
| cwrComplianceRadioRFGroup OBJECT-GROUP Group of objects implemented in the point to point wireless system for managing the Radio Frequency resources on the link. | 1.3.6.1.4.1.9.10.52.2.2.1 | current |
| cwrComplianceRadioImageGroup OBJECT-GROUP Group of objects implemented in the point to point wireless system for managing images related to the point-to-point wireless firmware. | 1.3.6.1.4.1.9.10.52.2.2.2 | current |
| cwrComplianceRadioLEDGroup OBJECT-GROUP Group of objects implemented in the point to point wireless card to provide information about the LEDs on the card. | 1.3.6.1.4.1.9.10.52.2.2.3 | current |
| cwrComplianceRadioDuplexorGroup OBJECT-GROUP Group of objects implemented in the point to point wireless card to provide information about the duplexor's in the system. | 1.3.6.1.4.1.9.10.52.2.2.4 | current |