MIBs Depot

CISCO-WAN-3G-MIB

Registered at
1.3.6.1.4.1.9.9.661
Last updated
2013-08-12 00:00
Organization
Cisco Systems, Inc.
Revisions
2013-08-12 00:00, 2012-07-25 00:00, 2012-07-10 00:00, 2010-08-11 00:00, 2010-08-04 00:00, 2009-02-05 00:00
Namespace
cisco
Source file
CISCO-WAN-3G-MIB
Digest
sha256:22421dd2ce21530c2b5428232917f879bd488b4768c5e32ab008eb5311aee8af

Description

This MIB module provides network management support for Cisco cellular 3G and 4G LTE WAN products. *** ABBREVIATIONS, ACRONYMS, AND SYMBOLS *** 1xRTT - 1 times Radio Transmission Technology. 3G - Third generation of mobile phones standards and technologies. 4G - Fourth generation of mobile phones standards and technologies Azimuth - Angle of rotation of a satellite Dish. BER - Bit Error Ratio. BS - Base Station. CDMA - Code Division Multiple Access. dB - decibel. dBm - power ratio in decibels (dB) of the measured power referenced to one milliwatt (mW). CnS - Control and Status proprietary protocol for managing the control and status of the modem. Ec/Io - ratio of received pilot energy, Ec, to total received energy or the total power spectral density, Io. EDGE - Enhanced Data rate for GSM Evolution. EPS - Evolved Packet System EVDO - EVolution Data Optimized. FDD - Frequency Division Duplexing GPRS - General Packet Radio Service. GSM - Global System for Mobile communications. GPS - Global Positioning System. HSDPA - High Speed Downlink Packet Access. HSPA - High Speed Packet Access. HSUPA - High Speed Uplink Packet Access. LBS - Location Based Service. LTE - Long Term Evolution MT - Mobile Termination. PDP - Packet Data Protocol. PLMN - Public Land Mobile Network. QoS - Quality of Service. RSSI - Received Signal Strength Indication. SDU - Service Data Unit. SER - SDU Error Ratio. SIM - Subscriber Identity Module. SMS - Short Messaging Service. SNR - Signal to Noise Ratio. TDD - Time Division Duplexing UMTS - Universal Mobile Telecommunication System. WCDMA - Wideband Code Division Multiple Access.

Contact

Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-3g@cisco.com cs-4g@cisco.com

Imports

FromSymbols
CISCO-SMIciscoMgmt
ENTITY-MIBentPhysicalIndex, entPhysicalName
IF-MIBifIndex
INET-ADDRESS-MIBInetAddress, InetAddressType
SNMP-FRAMEWORK-MIBSnmpAdminString
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP
SNMPv2-SMICounter32, Counter64, Gauge32, Integer32, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, Unsigned32, iso
SNMPv2-TCDisplayString, RowStatus, TEXTUAL-CONVENTION, TruthValue

Imported by

1 module(s) in this corpus import this one.

Load order

Every file a consumer needs in order to load this module, dependencies first.

CISCO-SMI
CISCO-WAN-3G-MIB
ENTITY-MIB
IANA-ENTITY-MIB
IANAifType-MIB
IF-MIB
INET-ADDRESS-MIB
SNMP-FRAMEWORK-MIB
SNMPv2-CONF
SNMPv2-MIB
SNMPv2-SMI
SNMPv2-TC
UUID-TC-MIB

Textual conventions

NameOIDSyntaxAccessStatus
C3gEcIo
TEXTUAL-CONVENTION
Generic EcIo range.
current
C3gGprsQosDelay
TEXTUAL-CONVENTION
GPRS QoS delay classes: subscription(1) - based on user's subscription delayClass1(2) - delay class 1 delayClass2(3) - delay class 2 delayClass3(4) - delay class 3 delayClass4(5) - delay class 4
current
C3gGprsQosMeanRate
TEXTUAL-CONVENTION
GPRS QoS mean rate: subscription(1) - based on user's subscription rate100(2) - 100 octet/hour rate200(3) - 200 octet/hour rate500(4) - 500 octet/hour rate1k(5) - 1000 octet/hour rate2k(6) - 2000 octet/hour rate5k(7) - 5000 octet/hour rate10k(8) - 10000 octet/hour rate20k(9) - 20000 octet/hour rate50k(10) - 50000 octet/hour rate100k(11) - 100000 octet/hour rate200k(12) - 200000 octet/hour rate500k(13) - 500000 octet/hour rate1m(14) - 1000000 octet/hour rate2m(15) - 2000000 octet/hour rate5m(16) - 5000000 octet/hour rate10m(17) - 10000000 octet/hour rate20m(18) - 20000000 octet/hour rate50m(19) - 50000000 octet/hour resv1(20) - reserved 1 (for future use) resv2(21) - reserved 2 (for future use) resv3(22) - reserved 3 (for future use) resv4(23) - reserved 4 (for future use) resv5(24) - reserved 5 (for future use) resv6(25) - reserved 6 (for future use) resv7(26) - reserved 7 (for future use) resv8(27) - reserved 8 (for future use) resv9(28) - reserved 9 (for future use) resv10(29) - reserved 10 (for future use) resv11(30) - reserved 11 (for future use) resv12(31) - reserved 12 (for future use) bestEffort(32) - best effort
current
C3gGprsQosPeakRate
TEXTUAL-CONVENTION
GPRS QoS peak rate: subscription(1) - based on user's subscription upTo1kops(2) - up to 1000 octet/second upTo2kops(3) - up to 2000 octet/second upTo4kops(4) - up to 4000 octet/second upTo8kops(5) - up to 8000 octet/second upTo16kops(6) - up to 16000 octet/second upTo32kops(7) - up to 32000 octet/second upTo64kops(8) - up to 64000 octet/second upTo128kops(9) - up to 128000 octet/second upTo256kops(10) - up to 256000 octet/second
current
C3gGprsQosPrecedence
TEXTUAL-CONVENTION
GPRS QoS precedence: subscription(1) - based on user's subscription highPriority(2) - high priority normalPriority(3) - normal priority lowPriority(4) - low priority
current
C3gGprsQosReliability
TEXTUAL-CONVENTION
GPRS QoS reliability: subscription(1) - based on user's subscription ackGtpLlcRlcProtData(2) - acknowledged GTP, LLC, and RLC; protected data unAckGtpAckLlcRlcProtData(3) - unacknowledged GTP, acknowledged LLC and RLC; protected data unAckGtpLlcAckRlcProtData(4) - unacknowledged GTP and LLC, acknowledged RLC; protected data unAckGtpLlcRlcProtData(5) - unacknowledged GTP, LLC, and RLC; protected data unAckGtpLlcRlcUnProtData(6) - unacknowledged GTP, LLC, and RLC; unprotected data
current
C3gPdpType
TEXTUAL-CONVENTION
Generic PDP type.
current
C3gRssi
TEXTUAL-CONVENTION
Generic RSSI range.
current
C3gServiceCapability
TEXTUAL-CONVENTION
3G service capability: oneXRtt(0) - 1xRTT evDoRel0(1) - EVDO Revision 0 evDoRelA(2) - EVDO Revision A evDoRelB(3) - EVDO Revision B gprs(4) - GPRS edge(5) - EDGE umtsWcdma(6) - UMTS/WCDMA hsdpa(7) - HSDPA hsupa(8) - HSUPA hspa(9) - HSPA hspaPlus(10) - HSPA Plus lteTdd(11) - LTE TDD lteFdd (12) - LTE FDD
current
C3gTemperature
TEXTUAL-CONVENTION
Generic temperature range.
current
C3gUmtsQosBer
TEXTUAL-CONVENTION
UMTS QoS residual bit error ratio (BER): subscription(1) - based on user's subscription fiveExpMinus2(2) - 5E-2 oneExpMinus2(3) - 1E-2 fiveExpMinus3(4) - 5E-3 fourExpMinus3(5) - 4E-3 oneExpMinus3(6) - 1E-3 oneExpMinus4(7) - 1E-4 oneExpMinus5(8) - 1E-5 oneExpMinus6(9) - 1E-6 sixExpMinus8(10) - 6E-8
current
C3gUmtsQosErroneousSdu
TEXTUAL-CONVENTION
UMTS QoS Delivery of Erroneous Service Data Unit(SDU): subscription(1) - based on user's subscription noDetect(2) - no detect errSduDeliver(3) - erroneous SDUs are delivered errSduNotDeliver(4) - erroneous SDUs are not delivered
current
C3gUmtsQosLinkBitRate
TEXTUAL-CONVENTION
UMTS QoS link bit rate: subscription(1) - based on user's subscription rate16kbps(2) - 16 Kbps rate32kbps(3) - 32 Kbps rate64kbps(4) - 64 Kbps rate128kbps(5) - 128 Kbps rate256kbps(6) - 256 Kbps rate384kbps(7) - 384 Kbps rate1dot8mbps(8) - 1.8 Mbps rate3dot6mbps(9) - 3.6 Mbps rate7dot2mbps(10) - 7.2 Mbps rate14dot4mbps(11) - 14.4 Mbps rate56kbps(12) - 56 Kbps rate1dot15mbps(13) - 1.15 Mbps rate1dot6mbps(14) - 1.6 Mbps rate2dot1mbps(15) - 2.1 Mbps rate2dot8mbps(16) - 2.8 Mbps rate4dot2mbps(17) - 4.2 Mbps rate8dot4mbps(18) - 8.4 Mbps
current
C3gUmtsQosOrder
TEXTUAL-CONVENTION
UMTS QoS delivery order: subscription(1) - based on user's subscription withDeliverOrder(2) - with delivery order withoutDeliverOrder(3) - without delivery order
current
C3gUmtsQosPriority
TEXTUAL-CONVENTION
UMTS QoS traffic handling priority: subscription(1) - based on user's subscription level1(2) - priority level 1 level2(3) - priority level 2 level3(4) - priority level 3
current
C3gUmtsQosSer
TEXTUAL-CONVENTION
UMTS QoS SDU error ratio: subscription(1) - based on user's subscription oneExpMinus2(2) - 1E-2 sevenExpMinus3(3) - 7E-3 oneExpMinus3(4) - 1E-3 oneExpMinus4(5) - 1E-4 oneExpMinus5(6) - 1E-5 oneExpMinus6(7) - 1E-6 oneExpMinus1(8) - 1E-1
current
C3gUmtsQosSignalIndication
TEXTUAL-CONVENTION
UMTS QoS signalling indication: notOptimized(1) - not optimized for signalling traffic optimized(2) - optimized for signalling traffic
current
C3gUmtsQosSrcStatDescriptor
TEXTUAL-CONVENTION
UMTS QoS source statistics descriptor: unknown(1) - unknown speech(2) - speech
current
C3gUmtsQosTrafficClass
TEXTUAL-CONVENTION
UMTS QoS traffic classes: subscription(1) - based on user's subscription conversational(2) - conversational streaming(3) - streaming interactive(4) - interactive background(5) - background
current

Objects

NameOIDSyntaxAccessStatus
ciscoWan3gMIBNotifs
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.661.0
ciscoWan3gMIBObjects
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.661.1
c3gWanCommonTable
OBJECT-TYPE
Cellular common objects table which is technology independent.
1.3.6.1.4.1.9.9.661.1.1not-accessiblecurrent
c3gWanCommonEntry
OBJECT-TYPE
An entry (conceptual row) in the c3gWanCommonTable.
1.3.6.1.4.1.9.9.661.1.1.1not-accessiblecurrent
c3gStandard
OBJECT-TYPE
Cellular Standard: GSM (Global System for Mobile communications, 3GPP), CDMA (Code Division Multiple Access, 3GPP-2). GSM standard also include 4G-LTE technology mode
1.3.6.1.4.1.9.9.661.1.1.1.1INTEGER {cdma(1), gsm(2)}read-onlycurrent
c3gCapability
OBJECT-TYPE
Cellular service capability. It currently includes the 2G, 3G and 4G-LTE standard.
1.3.6.1.4.1.9.9.661.1.1.1.2C3gServiceCapabilityread-onlycurrent
c3gModemState
OBJECT-TYPE
Cellular modem state, up(2) indicates modem can be detected and down(3) indicates modem can not be detected.
1.3.6.1.4.1.9.9.661.1.1.1.3INTEGER {unknown(1), up(2), down(3)}read-onlycurrent
c3gPreviousServiceType
OBJECT-TYPE
This object indicates the previous service type when service type changes.
1.3.6.1.4.1.9.9.661.1.1.1.4C3gServiceCapabilityread-onlycurrent
c3gCurrentServiceType
OBJECT-TYPE
This object indicates the current service type when service type changes.
1.3.6.1.4.1.9.9.661.1.1.1.5C3gServiceCapabilityread-onlycurrent
c3gRoamingStatus
OBJECT-TYPE
Cellular current roaming status.
1.3.6.1.4.1.9.9.661.1.1.1.6INTEGER {unknown(1), roaming(2), home(3)}read-onlycurrent
c3gCurrentSystemTime
OBJECT-TYPE
Cellular current system time received from base station.
1.3.6.1.4.1.9.9.661.1.1.1.7DisplayString (SIZE(0..64))read-onlycurrent
c3gConnectionStatus
OBJECT-TYPE
Indicates the current connection status.
1.3.6.1.4.1.9.9.661.1.1.1.8INTEGER {unknown(1), error(2), connecting(3), dormant(4), connected(5), disconnected(6), idle(7), active(8), inactive(9)}read-onlycurrent
c3gNotifRadioService
OBJECT-TYPE
This object is used as one of the var-bind object when notification for RSSI or Ec/Io is generated. This object indicates which service generates the notification.
1.3.6.1.4.1.9.9.661.1.1.1.9C3gServiceCapabilityread-onlycurrent
c3gNotifRssi
OBJECT-TYPE
This object is used as one of the var-bind object when notification for RSSI is generated. The relevant RSSI will be copied into c3gNotifRssi which corresponds to the service indicated in c3gNotifRadioService object. This object will reflect the value of one of the following objects: c3gCurrent1xRttRssi, c3gCurrentEvDoRssi and c3gCurrentGsmRssi. User should not use this object to get the current RSSI value as this object is used to indicate the RSSI value that triggers c3gRssiOnsetNotif or c3gRssiAbateNotif notification.
1.3.6.1.4.1.9.9.661.1.1.1.10C3gRssiread-onlycurrent
c3gNotifEcIo
OBJECT-TYPE
This object is used as one of the var-bind object when notification for Ec/Io is generated. The relevant Ec/Io will be copied into c3gNotifEcIo which corresponds to the service indicated in c3gNotifRadioService object. This object will reflect the value of one of the following objects: c3gCurrent1xRttEcIo, c3gCurrentEvDoEcIo and c3gCurrentGsmEcIo. User should not use this object to get the current Ec/Io value as this object is used to indicate the Ec/Io value that triggers c3gEcIoOnsetNotif or c3gEcIoAbateNotif notification.
1.3.6.1.4.1.9.9.661.1.1.1.11C3gEcIoread-onlycurrent
c3gModemTemperature
OBJECT-TYPE
The modem temperature.
1.3.6.1.4.1.9.9.661.1.1.1.12C3gTemperatureread-onlycurrent
c3gRssiOnsetNotifThreshold
OBJECT-TYPE
The RSSI onset threshold value. If RSSI goes below the threshold and the service bit in c3gRssiOnsetNotifFlag is set, the c3gRssiOnsetNotif notification for that service will be sent. The absolute value of c3gRssiAbateNotifThreshold should be less than or equal to the absolute value of c3gRssiOnsetNotifThreshold (|c3gRssiAbateNotifThreshold| <= |c3gRssiOnsetNotifThreshold|). e.g. setting c3gRssiAbateNotifThreshold to -115 dBm and then setting c3gRssiOnsetNotifThreshold to -110 dBm is not allowed and will be rejected.
1.3.6.1.4.1.9.9.661.1.1.1.13C3gRssiread-writecurrent
c3gRssiAbateNotifThreshold
OBJECT-TYPE
The RSSI abate threshold value. If RSSI goes above the threshold and the service bit in c3gRssiAbateNotifFlag is set, the c3gRssiAbateNotif notification for that service will be sent. The absolute value of c3gRssiAbateNotifThreshold should be less than or equal to the absolute value of c3gRssiOnsetNotifThreshold (|c3gRssiAbateNotifThreshold| <= |c3gRssiOnsetNotifThreshold|). e.g. setting c3gRssiAbateNotifThreshold to -115 dBm and then setting c3gRssiOnsetNotifThreshold to -110 dBm is not allowed and will be rejected.
1.3.6.1.4.1.9.9.661.1.1.1.14C3gRssiread-writecurrent
c3gEcIoOnsetNotifThreshold
OBJECT-TYPE
The EcIo onset threshold value. If EcIo goes below the threshold and the service bit in c3gEcIoOnsetNotifFlag is set, the c3gEcIoOnsetNotif notification for that service will be sent. The absolute value of c3gEcIoAbateNotifThreshold should be less than or equal to the absolute value of c3gEcIoOnsetNotifThreshold (|c3gEcIoAbateNotifThreshold| <= |c3gEcIoOnsetNotifThreshold|). e.g. setting c3gEcIoAbateNotifThreshold to -15 dB and then setting c3gEcIoOnsetNotifThreshold to -10 dB is not allowed and will be rejected.
1.3.6.1.4.1.9.9.661.1.1.1.15C3gEcIoread-writecurrent
c3gEcIoAbateNotifThreshold
OBJECT-TYPE
The threshold value that if EcIo goes above the threshold and the service bit in c3gEcIoAbateNotifFlag is set, the c3gEcIoAbateNotif notification for that service will be sent. The absolute value of c3gEcIoAbateNotifThreshold should be less than or equal to the absolute value of c3gEcIoOnsetNotifThreshold (|c3gEcIoAbateNotifThreshold| <= |c3gEcIoOnsetNotifThreshold|). e.g. setting c3gEcIoOnsetNotifThreshold to -15 dB and then setting c3gEcIoAbateNotifThreshold to -10 dB is not allowed and will be rejected.
1.3.6.1.4.1.9.9.661.1.1.1.16C3gEcIoread-writecurrent
c3gModemTemperOnsetNotifThreshold
OBJECT-TYPE
The modem temperature onset threshold value. If modem temperature goes above the threshold and the value of c3gModemTemperOnsetNotifEnabled is 'true', the c3gModemTemperOnsetNotif notification will be sent. The value of c3gModemTemperAbateNotifThreshold should be less than or equal to the value of c3gModemTemperOnsetNotifThreshold. e.g. setting c3gModemTemperAbateNotifThreshold to 50 degree Celsius and then setting c3gModemTemperOnsetNotifThreshold to 40 degree Celsius is not allowed and will be rejected.
1.3.6.1.4.1.9.9.661.1.1.1.17C3gTemperatureread-writecurrent
c3gModemTemperAbateNotifThreshold
OBJECT-TYPE
The modem temperature abate threshold value. If modem temperature goes below the threshold and the value of c3gModemTemperAbateNotifEnabled is 'true', the c3gModemTemperAbateNotif notification will be sent. The value of c3gModemTemperAbateNotifThreshold should be less than or equal to the value of c3gModemTemperOnsetNotifThreshold. e.g. setting c3gModemTemperAbateNotifThreshold to 50 degree Celsius and then setting c3gModemTemperOnsetNotifThreshold to 40 degree Celsius is not allowed and will be rejected.
1.3.6.1.4.1.9.9.661.1.1.1.18C3gTemperatureread-writecurrent
c3gModemReset
OBJECT-TYPE
This object is used to reset or power-cycle the modem.
1.3.6.1.4.1.9.9.661.1.1.1.19INTEGER {reset(1), powerCycle(2)}read-writecurrent
c3gModemUpNotifEnabled
OBJECT-TYPE
This object is used to enable/disable the generation of modem up notification c3gModemUpNotif.
1.3.6.1.4.1.9.9.661.1.1.1.20TruthValueread-writecurrent
c3gModemDownNotifEnabled
OBJECT-TYPE
This object is used to enable/disable the generation of modem down notification c3gModemDownNotif.
1.3.6.1.4.1.9.9.661.1.1.1.21TruthValueread-writecurrent
c3gServiceChangedNotifEnabled
OBJECT-TYPE
This object is used to enable/disable the generation of service changed notification c3gServiceChangedNotif.
1.3.6.1.4.1.9.9.661.1.1.1.22TruthValueread-writecurrent
c3gNetworkChangedNotifEnabled
OBJECT-TYPE
This object is used to enable/disable the generation of network changed notification c3gNetworkChangedNotif.
1.3.6.1.4.1.9.9.661.1.1.1.23TruthValueread-writecurrent
c3gConnectionStatusChangedNotifFlag
OBJECT-TYPE
This object is the flag bitmap to control the generation of notification c3gConnectionStatusChangedNotif. e.g. setting bit 0 (error(0)) to 1 and bit 4 (disconnected(4)) to 1 will cause the notification c3gConnectionStatusChangedNotif to be generated when object c3gConnetionStatus changes the status to error or disconnected. The default value of this object is '00'H.
1.3.6.1.4.1.9.9.661.1.1.1.24Bits {unknown(0), error(1), connecting(2), dormant(3), connected(4), disconnected(5), idle(6), active(7), inactive(8)}read-writecurrent
c3gRssiOnsetNotifFlag
OBJECT-TYPE
This object is the flag bitmap to control the generation of notification c3gRssiOnsetNotif. Each bit represents a service as defined in C3gServiceCapability, set the bit value to 1 to enable (and 0 to disable) the generation of notification c3gRssiOnsetNotif for that service. The default value of this object is all bits are 0.
1.3.6.1.4.1.9.9.661.1.1.1.25C3gServiceCapabilityread-writecurrent
c3gRssiAbateNotifFlag
OBJECT-TYPE
This object is the flag bitmap to control the generation of notification c3gRssiAbateNotif. Each bit represents a service as defined in C3gServiceCapability, set the bit value to 1 to enable (and 0 to disable) the generation of notification c3gRssiAbateNotif for that service. The default value of this object is all bits are 0.
1.3.6.1.4.1.9.9.661.1.1.1.26C3gServiceCapabilityread-writecurrent
c3gEcIoOnsetNotifFlag
OBJECT-TYPE
This object is the flag bitmap to control the generation of notification c3gEcIoOnsetNotif. Each bit represents a service as defined in C3gServiceCapability, set the bit value to 1 to enable (and 0 to disable) the generation of notification c3gEcIoOnsetNotif for that service. The default value of this object is all bits are 0.
1.3.6.1.4.1.9.9.661.1.1.1.27C3gServiceCapabilityread-writecurrent
c3gEcIoAbateNotifFlag
OBJECT-TYPE
This object is the flag bitmap to control the generation of notification c3gEcIoAbateNotif. Each bit represents a service as defined in C3gServiceCapability, set the bit value to 1 to enable (and 0 to disable) the generation of notification c3gEcIoAbateNotif for that service. The default value of this object is all bits are 0.
1.3.6.1.4.1.9.9.661.1.1.1.28C3gServiceCapabilityread-writecurrent
c3gModemTemperOnsetNotifEnabled
OBJECT-TYPE
This object is used to enable/disable the generation of c3gModemTemperOnsetNotif notification.
1.3.6.1.4.1.9.9.661.1.1.1.29TruthValueread-writecurrent
c3gModemTemperAbateNotifEnabled
OBJECT-TYPE
This object is used to enable/disable the generation of c3gModemTemperAbateNotif notification.
1.3.6.1.4.1.9.9.661.1.1.1.30TruthValueread-writecurrent
c3gGpsState
OBJECT-TYPE
This object is used to determine or enable/disable the GPS state.
1.3.6.1.4.1.9.9.661.1.1.1.31TruthValueread-writecurrent
c3gWanCdma
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.661.1.2
c3gCdmaSessionTable
OBJECT-TYPE
This table describes wireless session (link) created when a modem connects to a particular cellular network. One or more logical calls can be placed over wireless session(link). These logical calls are represented in the c3gCdmaConnectionTable.
1.3.6.1.4.1.9.9.661.1.2.1not-accessiblecurrent
c3gCdmaSessionEntry
OBJECT-TYPE
An entry (conceptual row) in the c3gCdmaSessionTable.
1.3.6.1.4.1.9.9.661.1.2.1.1not-accessiblecurrent
c3gCdmaTotalCallDuration
OBJECT-TYPE
Total duration of all calls.
1.3.6.1.4.1.9.9.661.1.2.1.1.1Counter64read-onlycurrent
c3gCdmaTotalTransmitted
OBJECT-TYPE
Total data transmitted for all calls. It is the total amount of data transmitted by modem, not to be confused with the number of bytes transmitted through the interface.
1.3.6.1.4.1.9.9.661.1.2.1.1.2Counter64read-onlycurrent
c3gCdmaTotalReceived
OBJECT-TYPE
Total data received for all calls. It is the total amount of data received by modem, not to be confused with the number of bytes received from the interface.
1.3.6.1.4.1.9.9.661.1.2.1.1.3Counter64read-onlycurrent
c3gHdrDdtmPreference
OBJECT-TYPE
HDR Data Dedicated Transmission Mode (DDTM) preference: unknown(1) - DDTM preference is unknown off(2) - DDTM preference set to OFF on(3) - DDTM preference set to ON noChange(4) - DDTM preference is no change
1.3.6.1.4.1.9.9.661.1.2.1.1.4INTEGER {unknown(1), off(2), on(3), noChange(4)}read-writecurrent
c3gCdmaConnectionTable
OBJECT-TYPE
Cellular 3G CDMA connection table. This table describes logical connections/calls over wireless link, the wireless link is described in c3gCdmaSessionTable.
1.3.6.1.4.1.9.9.661.1.2.2not-accessiblecurrent
c3gCdmaConnectionEntry
OBJECT-TYPE
An entry (conceptual row) in the c3gCdmaConnectionTable.
1.3.6.1.4.1.9.9.661.1.2.2.1not-accessiblecurrent
c3gOutgoingCallNumber
OBJECT-TYPE
Phone number of outgoing call.
1.3.6.1.4.1.9.9.661.1.2.2.1.1DisplayString (SIZE(0..64))read-onlycurrent
c3gHdrAtState
OBJECT-TYPE
High Data Rate (HDR) Access Terminal (AT) state.
1.3.6.1.4.1.9.9.661.1.2.2.1.2INTEGER {unknown(1), inactive(2), acquisition(3), sync(4), idle(5), access(6), connected(7)}read-onlycurrent
c3gHdrSessionState
OBJECT-TYPE
High Data Rate (HDR) session state.
1.3.6.1.4.1.9.9.661.1.2.2.1.3INTEGER {unknown(1), open(2), close(3), addressManagementProtocolSetup(4), atInitiated(5), anInitiated(6)}read-onlycurrent
c3gUati
OBJECT-TYPE
Unicast Access Terminal Identifier (UATI), AT seeking access to the 1 times EV-DO system receives a UATI allocated from the system after setting up a radio traffic channel with a base station.
1.3.6.1.4.1.9.9.661.1.2.2.1.4DisplayString (SIZE(0..64))read-onlycurrent
c3gColorCode
OBJECT-TYPE
Color code. A sync channel may be used by the base station to communicate administrative information to a mobile station. For example, a base station may transmit a base station ID to a user, a color code and administrative information identifying system status.
1.3.6.1.4.1.9.9.661.1.2.2.1.5Unsigned32read-onlycurrent
c3gRati
OBJECT-TYPE
Random Access Terminal Identifier (RATI). AT transmits a UATI request message to the ANC using the RATI to make a UATI allocation request.
1.3.6.1.4.1.9.9.661.1.2.2.1.6Unsigned32read-onlycurrent
c3gHdrSessionDuration
OBJECT-TYPE
HDR connection session duration. It is the duration between c3gHdrSessionStart and c3gHdrSessionEnd.
1.3.6.1.4.1.9.9.661.1.2.2.1.7Unsigned32read-onlycurrent
c3gHdrSessionStart
OBJECT-TYPE
HDR connection session starting time.
1.3.6.1.4.1.9.9.661.1.2.2.1.8Unsigned32read-onlycurrent
c3gHdrSessionEnd
OBJECT-TYPE
HDR connection session ending time.
1.3.6.1.4.1.9.9.661.1.2.2.1.9Unsigned32read-onlycurrent
c3gAuthStatus
OBJECT-TYPE
Connection authentication status: unknown(1) - authentication status is unknown notAuthenticated(2) - not yet authenticated. authenticated(3) - authenticated. failed(4) - authentication failed. authenticationDisabled(5) - authentication disabled
1.3.6.1.4.1.9.9.661.1.2.2.1.10INTEGER {unknown(1), notAuthenticated(2), authenticated(3), failed(4), authenticationDisabled(5)}read-onlycurrent
c3gHdrDrc
OBJECT-TYPE
High Data Rate (HDR) Data Rate Control (DRC). AT provides requests for data transmissions by sending a Data Rate Control, DRC, message via a specific channel referred to as the DRC channel.
1.3.6.1.4.1.9.9.661.1.2.2.1.11Unsigned32read-onlycurrent
c3gHdrDrcCover
OBJECT-TYPE
HDR DRC cover. The DRC cover is a coding applied to identify the sector from which the data is to be transmitted. In one embodiment, the DRC cover is a Walsh code applied to the DRC value, wherein a unique code corresponds to each sector in the Active Set of the AT.
1.3.6.1.4.1.9.9.661.1.2.2.1.12Unsigned32read-onlycurrent
c3gHdrRri
OBJECT-TYPE
HDR Rate Request Indicator (RRI). RRI provides the structure of a frame currently being transmitted when frames are transmitted at different rates. Services at different rates are reliably provided by the RRI: unknown(1) - RRI unknown pilotOnly(2) - pilot channel only rri9dot6kbps(3) - RRI is 9.6 Kbit/s rri19dot2kbps(4) - RRI is 19.2 Kbit/s rri38dot4kbps(5) - RRI is 38.4 Kbit/s rri76dot8kbps(6) - RRI is 76.8 Kbit/s rri153dot6kbps(7) - RRI is 153.6 Kbit/s
1.3.6.1.4.1.9.9.661.1.2.2.1.13INTEGER {unknown(1), pilotOnly(2), rri9dot6kbps(3), rri19dot2kbps(4), rri38dot4kbps(5), rri76dot8kbps(6), rri153dot6kbps(7)}read-onlycurrent
c3gMobileIpErrorCode
OBJECT-TYPE
Mobile IP error code (please refer to RFC 2002).
1.3.6.1.4.1.9.9.661.1.2.2.1.14Integer32read-onlycurrent
c3gCdmaCurrentTransmitted
OBJECT-TYPE
Current number of bytes transmitted by modem for current connection.
1.3.6.1.4.1.9.9.661.1.2.2.1.15Counter64read-onlycurrent
c3gCdmaCurrentReceived
OBJECT-TYPE
Current number of bytes received by modem for current connection.
1.3.6.1.4.1.9.9.661.1.2.2.1.16Counter64read-onlycurrent
c3gCdmaCurrentCallStatus
OBJECT-TYPE
Current call status.
1.3.6.1.4.1.9.9.661.1.2.2.1.17INTEGER {unknown(1), error(2), connecting(3), dormant(4), connected(5), disconnected(6)}read-onlycurrent
c3gCdmaCurrentCallDuration
OBJECT-TYPE
Current call duration.
1.3.6.1.4.1.9.9.661.1.2.2.1.18Unsigned32read-onlycurrent
c3gCdmaCurrentCallType
OBJECT-TYPE
Current call type.
1.3.6.1.4.1.9.9.661.1.2.2.1.19INTEGER {unknown(1), asyncData(2), voiceCall(3), packet1xRttCall(4), atAsyncDataCall(5), atVoiceCall(6), atPacketCall(7), faxCall(8), smsCall(9), otaCall(10), testCall(11), callWaiting(12), positionDetermination(13), dormant(14), e911Call(15)}read-onlycurrent
c3gCdmaLastCallDisconnReason
OBJECT-TYPE
Last call disconnect reason: unknown(1) - Unknown modemOffline(2) - Modem offline modemCdmaLocTilPowCyc(3) - Modem CDMA locked till power cycle noService(4) - No service abnormalCallEnd(5) - Abnormal call end baseStatIntercept(6) - Base station intercept baseStatRelease(7) - Base station release baseStatReleaseNoReas(8) - Base station release (No reason) baseStatReleaseSoRej(9) - Base station release (SO reject) incomingCall(10) - Incoming call baseStatAlertStop(11) - Base station alert stop clientEndedCall(12) - Client ended call activationEndedOtasp(13) - Activation ended OTASP (Over- The-Air Service Provisioning) ndssFailure(14) - NDSS (Network and Distributed System Security) failure maxAccesProbTransmit(15) - Max access probes transmitted persistTestFailure(16) - Persistence test failure ruimNotPresent(17) - RUIM (Removable User Identity Module) not present accessAttemptInProg(18) - Access attempt in progress reasonUnspecified(19) - Reason unspecified recdRetryOrder(20) - Recd retry order modemLocked(21) - Modem Locked gpsCallEnded(22) - GPS call ended smsCallEnded(23) - SMS (Short Message Service) call ended noConcurrentService(24) - No concurrent service noResponseFromBs(25) - No response from BS (Base station) rejectedByBs(26) - Rejected by BS notCompatConcurServ(27) - Not compatible concurrent service accessBlockedByBs(28) - Access blocked by BS alreadyOnTraffChann(29) - Already on Traffic channel emergencyCall(30) - Emergency call dataCallEnded(31) - Data call ended busyHdr(32) - Busy (HDR) billingOrAuthErrHdr(33) - Billing or Auth error (HDR) sysChangeDueToPrlHdr(34) - System change due to PRL (HDR) hdrExitDueToPrl(35) - HDR exit due to PRL (HDR) noSessionHdr(36) - No Session (HDR) callEndedHdr(37) - Call ended (HDR)
1.3.6.1.4.1.9.9.661.1.2.2.1.20INTEGER {unknown(1), modemOffline(2), modemCdmaLocTilPowCyc(3), noService(4), abnormalCallEnd(5), baseStatIntercept(6), baseStatRelease(7), baseStatReleaseNoReas(8), baseStatReleaseSoRej(9), incomingCall(10), baseStatAlertStop(11), clientEndedCall(12), activationEndedOtasp(13), ndssFailure(14), maxAccesProbTransmit(15), persistTestFailure(16), ruimNotPresent(17), accessAttemptInProg(18), reasonUnspecified(19), recdRetryOrder(20), modemLocked(21), gpsCallEnded(22), smsCallEnded(23), noConcurrentService(24), noResponseFromBs(25), rejectedByBs(26), notCompatConcurServ(27), accessBlockedByBs(28), alreadyOnTraffChann(29), emergencyCall(30), dataCallEnded(31), busyHdr(32), billingOrAuthErrHdr(33), sysChangeDueToPrlHdr(34), hdrExitDueToPrl(35), noSessionHdr(36), callEndedHdr(37)}read-onlycurrent
c3gCdmaLastConnError
OBJECT-TYPE
Last connect error: none(1) - None invalidClientId(2) - Invalid client ID badCallType(3) - Bad call type badServiceType(4) - Bad service type expectingNumber(5) - Expecting number nullNumberBuffer(6) - Null number buffer invalidDigits(7) - Invalid digits outOfRangeNumber(8) - Out of range number nullAalphaBuffer(9) - Null alpha buffer outOfRangeAlphaNumber(10) - Out of range alpha number invalidOtaspActivatCode(11) - Invalid OTASP activation code modemOffline(12) - Modem offline modemLocked(13) - Modem locked unsupportedFlash(14) - Unsupported flash dialedNumberProhibited(15) - Dialed number prohibited onlyE911Calls(16) - Only E911 calls modemInUse(17) - Modem in use unsupportedServiceType(18) - Unsupported service type wrongCallType(19) - Wrong call type invalidCommandCallState(20) - Invalid command (call state) invalidCommandModemState(21) - Invalid command (modem state) noValidService(22) - No valid service cannotAnswerIncomingCall(23) - Cannot answer incoming call badPrivacySetting(24) - Bad privacy setting noCommandBuffers(25) - No command buffers communicationProblem(26) - Communication problem unspecifiedError(27) - Unspecified error invalidLastActiveNetwork(28) - Invalid last active network noCollocatedHdr(29) - No collocated HDR uimNotPresent(30) - UIM (User Identity Module) not present
1.3.6.1.4.1.9.9.661.1.2.2.1.21INTEGER {none(1), invalidClientId(2), badCallType(3), badServiceType(4), expectingNumber(5), nullNumberBuffer(6), invalidDigits(7), outOfRangeNumber(8), nullAalphaBuffer(9), outOfRangeAlphaNumber(10), invalidOtaspActivatCode(11), modemOffline(12), modemLocked(13), unsupportedFlash(14), dialedNumberProhibited(15), onlyE911Calls(16), modemInUse(17), unsupportedServiceType(18), wrongCallType(19), invalidCommandCallState(20), invalidCommandModemState(21), noValidService(22), cannotAnswerIncomingCall(23), badPrivacySetting(24), noCommandBuffers(25), communicationProblem(26), unspecifiedError(27), invalidLastActiveNetwork(28), noCollocatedHdr(29), uimNotPresent(30)}read-onlycurrent
c3gCdmaIdentityTable
OBJECT-TYPE
Cellular 3G CDMA identity table.
1.3.6.1.4.1.9.9.661.1.2.3not-accessiblecurrent
c3gCdmaIdentityEntry
OBJECT-TYPE
An entry (conceptual row) in the c3gCdmaIdentityTable.
1.3.6.1.4.1.9.9.661.1.2.3.1not-accessiblecurrent
c3gEsn
OBJECT-TYPE
This object indicates Electronic Serial Number (ESN).
1.3.6.1.4.1.9.9.661.1.2.3.1.1DisplayString (SIZE(0..128))read-onlycurrent
c3gModemActivationStatus
OBJECT-TYPE
Modem activation status.
1.3.6.1.4.1.9.9.661.1.2.3.1.2INTEGER {unknown(1), activated(2), notActivated(3)}read-onlycurrent
c3gAccountActivationDate
OBJECT-TYPE
Modem account activation date.
1.3.6.1.4.1.9.9.661.1.2.3.1.3DisplayString (SIZE(0..128))read-onlycurrent
c3gCdmaRoamingPreference
OBJECT-TYPE
This object indicates the roaming preference: unknown(1) - preference unknown home(2) - home networks only affiliated(3) - roaming on affiliated networks any(4) - roaming on any network
1.3.6.1.4.1.9.9.661.1.2.3.1.4INTEGER {unknown(1), home(2), affiliated(3), any(4)}read-writecurrent
c3gPrlVersion
OBJECT-TYPE
Preferred Roaming List (PRL) version.
1.3.6.1.4.1.9.9.661.1.2.3.1.5Unsigned32read-onlycurrent
c3gMdn
OBJECT-TYPE
Mobile Directory Number (MDN), a dialable number assigned to a wireless phone.
1.3.6.1.4.1.9.9.661.1.2.3.1.6DisplayString (SIZE(0..64))read-writecurrent
c3gMsid
OBJECT-TYPE
Mobile Station Identifier (MSID), MSID is utilized to distinguish the mobile station being programmed from other mobile stations during messaging and paging processes, including the downloading of programming information to the mobile station.
1.3.6.1.4.1.9.9.661.1.2.3.1.7DisplayString (SIZE(0..64))read-writecurrent
c3gMsl
OBJECT-TYPE
Mobile Subscriber Lock (MSL).
1.3.6.1.4.1.9.9.661.1.2.3.1.8DisplayString (SIZE(0..64))read-writecurrent
c3gCdmaNetworkTable
OBJECT-TYPE
Cellular 3G CDMA network table.
1.3.6.1.4.1.9.9.661.1.2.4not-accessiblecurrent
c3gCdmaNetworkEntry
OBJECT-TYPE
An entry (conceptual row) in the c3gCdmaNetworkTable.
1.3.6.1.4.1.9.9.661.1.2.4.1not-accessiblecurrent
c3gCdmaCurrentServiceStatus
OBJECT-TYPE
Current service status.
1.3.6.1.4.1.9.9.661.1.2.4.1.1DisplayString (SIZE(0..64))read-onlycurrent
c3gCdmaHybridModePreference
OBJECT-TYPE
This object indicates the hybrid mode preference: unknown(1) - preference unknown hybrid(2) - connect to EV-DO/1xRTT services evDoOnly(3) - connect to only EV-DO service oneXRttOnly(4) - connect to only 1xRTT service
1.3.6.1.4.1.9.9.661.1.2.4.1.2INTEGER {unknown(1), hybrid(2), evDoOnly(3), oneXRttOnly(4)}read-writecurrent
c3gCdmaCurrentRoamingStatus
OBJECT-TYPE
Current 1xRTT roaming status, roaming is a general term in wireless telecommunications that refers to the extending of connectivity service in a location that is different from the home location where the service was registered: unknown(1) - roaming status is unknown. home(2) - connectivity service in home location. roamingWithSid(3) - roaming with SID. roamingWithoutSid(4) - roaming without SID
1.3.6.1.4.1.9.9.661.1.2.4.1.3INTEGER {unknown(1), home(2), roamingWithSid(3), roamingWithoutSid(4)}read-onlycurrent
c3gCurrentIdleDigitalMode
OBJECT-TYPE
Current idle digital mode: unknown(1) - service is unknown noService(2) - no service amps(3) - Advanced Mobile Phone Service (AMPS) cdma(4) - Code Division Multiple Access (CDMA) gsm(5) - Global System for Mobile communications (GSM) hdr(6) - High Data Rate (HDR) wcdma(7) - Wideband Code-Division Multiple-Access (WCDMA) gps(8) - Global Positioning System (GPS) lte(9) - Long Term Evolution (LTE)
1.3.6.1.4.1.9.9.661.1.2.4.1.4INTEGER {unknown(1), noService(2), amps(3), cdma(4), gsm(5), hdr(6), wcdma(7), gps(8), lte(9)}read-onlycurrent
c3gCurrentSid
OBJECT-TYPE
Current System Identifier (SID), SID is a 15-bit numeric identifiers used by cellular systems to identify the home system of a cellular telephone and by the cellular telephone to determine its roaming status. Value of '-1' indicates SID is 'Not Applicable'.
1.3.6.1.4.1.9.9.661.1.2.4.1.5Integer32 (-1..32767)read-writecurrent
c3gCurrentNid
OBJECT-TYPE
Current Network Identification (NID), NID is a 16-bit numeric identifiers used by cellular systems. Value of '-1' indicates NID is 'Not Applicable'.
1.3.6.1.4.1.9.9.661.1.2.4.1.6Integer32 (-1..65535)read-writecurrent
c3gCurrentCallSetupMode
OBJECT-TYPE
Current call setup mode. The 1xEV-DO system supports packet data connections to a public or private data network using either mobile IP or simple IP protocol. For simple IP protocol, moving from the coverage area of one PDSN to another PDSN constitutes a change in packet data session. For mobile IP protocol, a packet data session can span several PDSNs as long as the user continuously maintains mobility bindings at the Home Agent (the IP address is persistent). The modes are: unknown(1) - mode is unknown simpleIpOnly(2) - simple IP only mobileIpPreferWithSipFallback(3) - prefer mobile IP with simple IP as fallback mode mobileIpOnly(4) - mobile IP only
1.3.6.1.4.1.9.9.661.1.2.4.1.7INTEGER {unknown(1), simpleIpOnly(2), mobileIpPreferWithSipFallback(3), mobileIpOnly(4)}read-writecurrent
c3gSipUsername
OBJECT-TYPE
Simple IP (SIP) user name.
1.3.6.1.4.1.9.9.661.1.2.4.1.8DisplayString (SIZE(0..64))read-writecurrent
c3gSipPassword
OBJECT-TYPE
Simple IP (SIP) password.
1.3.6.1.4.1.9.9.661.1.2.4.1.9DisplayString (SIZE(0..64))read-writecurrent
c3gServingBaseStationLongitude
OBJECT-TYPE
Longitude of the serving base station.
1.3.6.1.4.1.9.9.661.1.2.4.1.10DisplayString (SIZE(0..64))read-onlycurrent
c3gServingBaseStationLatitude
OBJECT-TYPE
Latitude of the serving base station.
1.3.6.1.4.1.9.9.661.1.2.4.1.11DisplayString (SIZE(0..64))read-onlycurrent
c3gCdmaProfile
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.661.1.2.5
c3gCdmaProfileCommonTable
OBJECT-TYPE
Cellular 3G CDMA profile common table.
1.3.6.1.4.1.9.9.661.1.2.5.1not-accessiblecurrent
c3gCdmaProfileCommonEntry
OBJECT-TYPE
An entry (conceptual row) in the c3gCdmaProfileCommonTable.
1.3.6.1.4.1.9.9.661.1.2.5.1.1not-accessiblecurrent
c3gNumberOfDataProfileConfigurable
OBJECT-TYPE
The number of data profiles configurable.
1.3.6.1.4.1.9.9.661.1.2.5.1.1.1Unsigned32read-writecurrent
c3gCurrentActiveDataProfile
OBJECT-TYPE
The current active data profile.
1.3.6.1.4.1.9.9.661.1.2.5.1.1.2Unsigned32read-writecurrent
c3gCdmaProfileTable
OBJECT-TYPE
Cellular 3G CDMA profile table.
1.3.6.1.4.1.9.9.661.1.2.5.2not-accessiblecurrent
c3gCdmaProfileEntry
OBJECT-TYPE
An entry (conceptual row) in the c3gCdmaProfileTable.
1.3.6.1.4.1.9.9.661.1.2.5.2.1not-accessiblecurrent
c3gCdmaProfileIndex
OBJECT-TYPE
Profile index, combined with entPhysicalIndex to access the profile table c3gCdmaProfileTable.
1.3.6.1.4.1.9.9.661.1.2.5.2.1.1Integer32 (1..65535)not-accessiblecurrent
c3gNai
OBJECT-TYPE
Network Access Identifier (NAI). NAI is required to identify the mobile user and the network the mobile user intended to access. The NAI is provided by the mobile node to the dialed ISP during PPP authentication.
1.3.6.1.4.1.9.9.661.1.2.5.2.1.2DisplayString (SIZE(0..64))read-writecurrent
c3gAaaPassword
OBJECT-TYPE
This object indicates the password for AAA.
1.3.6.1.4.1.9.9.661.1.2.5.2.1.3DisplayString (SIZE(0..64))read-writecurrent
c3gMnHaSs
OBJECT-TYPE
Mobile Node (MN) Home Agent (HA) Shared Secret (SS) setting: set(1) - shared secret is set notSet(2) - shared secret is not set
1.3.6.1.4.1.9.9.661.1.2.5.2.1.4INTEGER {set(1), notSet(2)}read-writecurrent
c3gMnHaSpi
OBJECT-TYPE
Mobile Node (MN) Home Agent (HA) Security Parameter Index (SPI).
1.3.6.1.4.1.9.9.661.1.2.5.2.1.5Unsigned32read-writecurrent
c3gMnAaaSs
OBJECT-TYPE
Mobile Node (MN) Authentication Authorization Accounting (AAA) Shared Secret (SS) setting: set(1) - shared secret is set notSet(2) - shared secret is not set
1.3.6.1.4.1.9.9.661.1.2.5.2.1.6INTEGER {set(1), notSet(2)}read-writecurrent
c3gMnAaaSpi
OBJECT-TYPE
Mobile Node (MN) Authentication Authorization Accounting (AAA) Security Parameter Index (SPI).
1.3.6.1.4.1.9.9.661.1.2.5.2.1.7Unsigned32read-writecurrent
c3gReverseTunnelPreference
OBJECT-TYPE
Reverse tunnel preference.
1.3.6.1.4.1.9.9.661.1.2.5.2.1.8INTEGER {set(1), notSet(2)}read-writecurrent
c3gHomeAddrType
OBJECT-TYPE
A value that represents the type of the IP Address stored in the object c3gHomeAddr.
1.3.6.1.4.1.9.9.661.1.2.5.2.1.9InetAddressTyperead-writecurrent
c3gHomeAddr
OBJECT-TYPE
A unicast routable address assigned to a Mobile Node, used as the permanent address of the Mobile Node.
1.3.6.1.4.1.9.9.661.1.2.5.2.1.10InetAddressread-writecurrent
c3gPriHaAddrType
OBJECT-TYPE
A value that represents the type of the IP Address stored in the object c3gPriHaAddr.
1.3.6.1.4.1.9.9.661.1.2.5.2.1.11InetAddressTyperead-writecurrent
c3gPriHaAddr
OBJECT-TYPE
The primary home agent address.
1.3.6.1.4.1.9.9.661.1.2.5.2.1.12InetAddressread-writecurrent
c3gSecHaAddrType
OBJECT-TYPE
A value that represents the type of the IP Address stored in the object c3gSecHaAddr.
1.3.6.1.4.1.9.9.661.1.2.5.2.1.13InetAddressTyperead-writecurrent
c3gSecHaAddr
OBJECT-TYPE
The secondary home agent address.
1.3.6.1.4.1.9.9.661.1.2.5.2.1.14InetAddressread-writecurrent
c3gCdmaRadio
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.661.1.2.6
c3gCdma1xRttRadioTable
OBJECT-TYPE
Cellular 3G CDMA 1xRTT radio table.
1.3.6.1.4.1.9.9.661.1.2.6.1not-accessiblecurrent
c3gCdma1xRttRadioEntry
OBJECT-TYPE
An entry (conceptual row) in the c3gCdma1xRttRadioTable.
1.3.6.1.4.1.9.9.661.1.2.6.1.1not-accessiblecurrent
c3gCurrent1xRttRssi
OBJECT-TYPE
Current 1xRTT RSSI value.
1.3.6.1.4.1.9.9.661.1.2.6.1.1.1C3gRssiread-onlycurrent
c3gCurrent1xRttEcIo
OBJECT-TYPE
Current 1xRTT Ec/Io value.
1.3.6.1.4.1.9.9.661.1.2.6.1.1.2C3gEcIoread-onlycurrent
c3gCurrent1xRttChannelNumber
OBJECT-TYPE
Current 1xRTT channel number. Current channel number to which the modem is attached to the base station. Value of '-1' indicates 'No Service'.
1.3.6.1.4.1.9.9.661.1.2.6.1.1.3Integer32read-onlycurrent
c3gCurrent1xRttChannelState
OBJECT-TYPE
Current 1xRTT channel state. Indicates whether the modem is scanning or has acquired the channel.
1.3.6.1.4.1.9.9.661.1.2.6.1.1.4INTEGER {unknown(1), notAcquired(2), acquired(3), scanning(4)}read-onlycurrent
c3gCdma1xRttBandClassTable
OBJECT-TYPE
Cellular 3G CDMA 1xRTT band class table. This table contains band class information for each available band.
1.3.6.1.4.1.9.9.661.1.2.6.2not-accessiblecurrent
c3gCdma1xRttBandClassEntry
OBJECT-TYPE
An entry (conceptual row) in the c3gCdma1xRttBandClassTable.
1.3.6.1.4.1.9.9.661.1.2.6.2.1not-accessiblecurrent
c3gBandClassIndex
OBJECT-TYPE
Band class index, combined with entPhysicalIndex to access the band class table.
1.3.6.1.4.1.9.9.661.1.2.6.2.1.1Integer32 (1..32)not-accessiblecurrent
c3g1xRttBandClass
OBJECT-TYPE
This object contains 1xRTT band class.
1.3.6.1.4.1.9.9.661.1.2.6.2.1.2Unsigned32read-onlycurrent
c3gCdmaEvDoRadioTable
OBJECT-TYPE
Cellular 3G CDMA EV-DO radio table.
1.3.6.1.4.1.9.9.661.1.2.6.3not-accessiblecurrent
c3gCdmaEvDoRadioEntry
OBJECT-TYPE
An entry (conceptual row) in the c3gCdmaEvDoRadioTable.
1.3.6.1.4.1.9.9.661.1.2.6.3.1not-accessiblecurrent
c3gCurrentEvDoRssi
OBJECT-TYPE
Current EV-DO RSSI value.
1.3.6.1.4.1.9.9.661.1.2.6.3.1.1C3gRssiread-onlycurrent
c3gCurrentEvDoEcIo
OBJECT-TYPE
Current EV-DO Ec/Io value.
1.3.6.1.4.1.9.9.661.1.2.6.3.1.2C3gEcIoread-onlycurrent
c3gCurrentEvDoChannelNumber
OBJECT-TYPE
Current EV-DO channel number. Current channel number to which the modem is attached to the base station. Value of '-1' indicates 'No Service'.
1.3.6.1.4.1.9.9.661.1.2.6.3.1.3Integer32read-onlycurrent
c3gSectorId
OBJECT-TYPE
Sector ID of the base station to which the modem is attached.
1.3.6.1.4.1.9.9.661.1.2.6.3.1.4DisplayString (SIZE(0..64))read-onlycurrent
c3gSubnetMask
OBJECT-TYPE
Subnet mask of the sector, not to be confused with the IP subnet mask.
1.3.6.1.4.1.9.9.661.1.2.6.3.1.5Unsigned32read-onlycurrent
c3gHdrColorCode
OBJECT-TYPE
Color code of the sector.
1.3.6.1.4.1.9.9.661.1.2.6.3.1.6Unsigned32read-onlycurrent
c3gPnOffset
OBJECT-TYPE
PN offset. PN offset is a time offset from the beginning of the well-known pseudo-random noise sequence that is used to spread the signal from the base station.
1.3.6.1.4.1.9.9.661.1.2.6.3.1.7Unsigned32read-onlycurrent
c3gRxMainGainControl
OBJECT-TYPE
Received main gain control for the modem. value of '-1' indicates the received main gain control is unavailable.
1.3.6.1.4.1.9.9.661.1.2.6.3.1.8Integer32read-onlycurrent
c3gRxDiversityGainControl
OBJECT-TYPE
Received diversity for the modem. value of '-1' indicates the received diversity is unavailable.
1.3.6.1.4.1.9.9.661.1.2.6.3.1.9Integer32read-onlycurrent
c3gTxTotalPower
OBJECT-TYPE
Transmit total power.
1.3.6.1.4.1.9.9.661.1.2.6.3.1.10Integer32read-onlycurrent
c3gTxGainAdjust
OBJECT-TYPE
Transmit gain adjust.
1.3.6.1.4.1.9.9.661.1.2.6.3.1.11Integer32read-onlycurrent
c3gCarrierToInterferenceRatio
OBJECT-TYPE
Carrier to interference ratio. Carrier-to-Interference ratio (C/I) is the ratio of power in an RF carrier to the interference power in the channel.
1.3.6.1.4.1.9.9.661.1.2.6.3.1.12Unsigned32read-onlycurrent
c3gCdmaEvDoBandClassTable
OBJECT-TYPE
Cellular 3G CDMA EV-DO band class table. This table contains band class information for each available band.
1.3.6.1.4.1.9.9.661.1.2.6.4not-accessiblecurrent
c3gCdmaEvDoBandClassEntry
OBJECT-TYPE
An entry (conceptual row) in the c3gCdmaEvDoBandClassTable.
1.3.6.1.4.1.9.9.661.1.2.6.4.1not-accessiblecurrent
c3gEvDoBandClass
OBJECT-TYPE
This object contains EV-DO band class.
1.3.6.1.4.1.9.9.661.1.2.6.4.1.1Unsigned32read-onlycurrent
c3gCdmaHistoryTable
OBJECT-TYPE
Cellular 3G CDMA history table. The history of RSSI are carried in an octet of string. Each octet in the octet string has a value from 0 to 150 and the 255 value is reserved to indicate an uninitialized (Invalid) value. The format of the octet string with n octets is as following: [ octet 0 is latest, octet 1 is latest-1, . . octet n-2 is oldest-1, octet n-1 is oldest ] To convert the provided value into dBm the following formula should be used: dBm = (-1)*value;
1.3.6.1.4.1.9.9.661.1.2.6.5not-accessiblecurrent
c3gCdmaHistoryEntry
OBJECT-TYPE
An entry (conceptual row) in the c3gCdmaHistoryTable.
1.3.6.1.4.1.9.9.661.1.2.6.5.1not-accessiblecurrent
c3gCdmaHistory1xRttRssiPerSecond
OBJECT-TYPE
Per-second 1xRTT RSSI history. This object contains a per-second history of 1xRTT RSSI values for the last 60 seconds.
1.3.6.1.4.1.9.9.661.1.2.6.5.1.1OCTET STRING (SIZE(60))read-onlycurrent
c3gCdmaHistory1xRttRssiPerMinute
OBJECT-TYPE
Per-minute 1xRTT weakest RSSI value history. This object contains a per-minute history of 1xRTT weakest RSSI values for the last 60 minutes. The octet in the string is the weakest RSSI value measured in a minute interval.
1.3.6.1.4.1.9.9.661.1.2.6.5.1.2OCTET STRING (SIZE(60))read-onlycurrent
c3gCdmaHistory1xRttRssiPerHour
OBJECT-TYPE
Per-hour 1xRTT weakest RSSI value history. This object contains a per-hour history of 1xRTT weakest RSSI values for the last 72 hours. The octet in the string is the weakest RSSI value measured in an hour interval.
1.3.6.1.4.1.9.9.661.1.2.6.5.1.3OCTET STRING (SIZE(72))read-onlycurrent
c3gCdmaHistoryEvDoRssiPerSecond
OBJECT-TYPE
Per-second EV-DO RSSI history. This object contains a per-second history of EV-DO RSSI values for the last 60 seconds.
1.3.6.1.4.1.9.9.661.1.2.6.5.1.4OCTET STRING (SIZE(60))read-onlycurrent
c3gCdmaHistoryEvDoRssiPerMinute
OBJECT-TYPE
Per-minute EV-DO weakest RSSI value history. This object contains a per-minute history of EV-DO weakest RSSI values for the last 60 minutes. The octet in the string is the weakest RSSI value measured in a minute interval.
1.3.6.1.4.1.9.9.661.1.2.6.5.1.5OCTET STRING (SIZE(60))read-onlycurrent
c3gCdmaHistoryEvDoRssiPerHour
OBJECT-TYPE
Per-hour EV-DO weakest RSSI value history. This object contains a per-hour history of EV-DO weakest RSSI values for the last 72 hours. The octet in the string is the weakest RSSI value measured in an hour interval.
1.3.6.1.4.1.9.9.661.1.2.6.5.1.6OCTET STRING (SIZE(72))read-onlycurrent
c3gCdmaSecurity
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.661.1.2.7
c3gCdmaSecurityTable
OBJECT-TYPE
Cellular 3G CDMA security table.
1.3.6.1.4.1.9.9.661.1.2.7.1not-accessiblecurrent
c3gCdmaSecurityEntry
OBJECT-TYPE
An entry (conceptual row) in the c3gCdmaSecurityTable.
1.3.6.1.4.1.9.9.661.1.2.7.1.1not-accessiblecurrent
c3gCdmaPinSecurityStatus
OBJECT-TYPE
CDMA Personal Identification Number (PIN) security: unknown(1) - PIN security unknown locked(2) - PIN security is locked unlocked(3) - PIN security is unlocked
1.3.6.1.4.1.9.9.661.1.2.7.1.1.1INTEGER {unknown(1), locked(2), unlocked(3)}read-writecurrent
c3gCdmaPowerUpLockStatus
OBJECT-TYPE
CDMA power up lock: unknown(1) - power up lock unknown enabled(2) - power up lock enabled disabled(3) - power up lock disabled
1.3.6.1.4.1.9.9.661.1.2.7.1.1.2INTEGER {unknown(1), enabled(2), disabled(3)}read-writecurrent
c3gWanGsm
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.661.1.3
c3gGsmIdentityTable
OBJECT-TYPE
.
1.3.6.1.4.1.9.9.661.1.3.1not-accessiblecurrent
c3gGsmIdentityEntry
OBJECT-TYPE
An entry (conceptual row) in the c3gGsmIdentityTable.
1.3.6.1.4.1.9.9.661.1.3.1.1not-accessiblecurrent
c3gImsi
OBJECT-TYPE
International Mobile Subscriber Identifier (IMSI), a unique 15-digit code used to identify an individual user on a GSM/LTE network.
1.3.6.1.4.1.9.9.661.1.3.1.1.1DisplayString (SIZE(0..64))read-onlycurrent
c3gImei
OBJECT-TYPE
International Mobile Equipment Identifier (IMEI), a unique 15 or 17 digit code used to identify an individual mobile station to a GSM, UMTS or LTE network.
1.3.6.1.4.1.9.9.661.1.3.1.1.2DisplayString (SIZE(0..64))read-onlycurrent
c3gIccId
OBJECT-TYPE
This object indicates the Integrated Circuit Card ID (ICCID). The ICCID is defined by the ITU-T recommendation E.118. ICCIDs are stored in the SIM cards and are also engraved or printed on the SIM card body during a process called personalization.
1.3.6.1.4.1.9.9.661.1.3.1.1.3DisplayString (SIZE(0..64))read-onlycurrent
c3gMsisdn
OBJECT-TYPE
This object indicates the Mobile Subscriber Integrated Services Digital Network Number (MSISDN). It is a number uniquely identifying a subscription in a GSM, UMTS or LTE mobile network. It represents the telephone number to the SIM card in a mobile/cellular phone.
1.3.6.1.4.1.9.9.661.1.3.1.1.4DisplayString (SIZE(0..64))read-writecurrent
c3gFsn
OBJECT-TYPE
Forward Sequence Number (FSN), a message acknowledgement method using sequence number in the forward direction.
1.3.6.1.4.1.9.9.661.1.3.1.1.5DisplayString (SIZE(0..64))read-onlycurrent
c3gModemStatus
OBJECT-TYPE
Modem status: unknown(1) - modem status is unknown offLine(2) - modem is off line onLine(3) - modem is on line lowPowerMode(4) - modem is in the low power mode
1.3.6.1.4.1.9.9.661.1.3.1.1.6INTEGER {unknown(1), offLine(2), onLine(3), lowPowerMode(4)}read-onlycurrent
c3gGsmRoamingPreference
OBJECT-TYPE
This object indicates the roaming preference.
1.3.6.1.4.1.9.9.661.1.3.1.1.7INTEGER {unknown(1), home(2), roaming(3)}read-writecurrent
c3gGsmNetworkTable
OBJECT-TYPE
Cellular GSM Network table. This table is applicable in both 3G and 4G-LTE technology mode
1.3.6.1.4.1.9.9.661.1.3.2not-accessiblecurrent
c3gGsmNetworkEntry
OBJECT-TYPE
An entry (conceptual row) in the c3gGsmNetworkTable.
1.3.6.1.4.1.9.9.661.1.3.2.1not-accessiblecurrent
c3gGsmLac
OBJECT-TYPE
Location Area Code (LAC), also called as Tracking Area Code (TAC) in LTE standard. LAC/TAC is given by the base station.
1.3.6.1.4.1.9.9.661.1.3.2.1.1Unsigned32read-onlycurrent
c3gGsmCurrentServiceStatus
OBJECT-TYPE
Current Service Status: unknown(1) - current service status is unknown noService(2) - no service normal(3) - service status is normal emergencyOnly(4) - emergency service only
1.3.6.1.4.1.9.9.661.1.3.2.1.2INTEGER {unknown(1), noService(2), normal(3), emergencyOnly(4)}read-onlycurrent
c3gGsmCurrentServiceError
OBJECT-TYPE
Current service error: unknown(1) - Unknown none(2) - None imsiUnknownInHlr(3) - IMSI unknown in HLR (Home Location Register) illegalMs(4) - Illegal MS (Mobile Station) imsiUnknownInVlr(5) - IMSI unknown in VLR (Visitor Location Register) imeiNotAccepted(6) - IMEI not accepted illegalMe(7) - Illegal ME (Mobile Entity) gprsServNotAllowed(8) - GPRS services not allowed gprsNonGprsServNotAllow(9) - GPRS and non-GPRS services not allowed msIdentUnknown(10) - MS identity unknown implicitlyDetached(11) - Implicitly detached plmnNotAllowed(12) - PLMN not allowed lacNotAllowed(13) - LAC not allowed roamingNotAllowed(14) - Roaming not allowed gprsServNotAllowInPlmn(15) - GPRS services not allowed in this PLMN noSuitableCellInLa(16) - No suitable cells in LA (Location Area) mscTempNotReachable(17) - MSC (Mobile Switching Center) temporarily not reachable networkFailure(18) - Network failure macFailure(19) - MAC failure synchFailure(20) - Synch failure congestion(21) - Congestion gsmAuthenNotAccept(22) - GSM/LTE Authentication not accepted servOptionNotSupport(23) - Service option not supported reqServOptionNotSub(24) - Requested service option not subscribed servOptionOutOfOrder(25) - Service option out of order callCannotIdentified(26) - Call cannot be identified noPdpContextActivated(27) - No PDP context activated invalidMandatInfo(28) - Invalid mandatory info unpsecProtErr(29) - Unspecified protocol error
1.3.6.1.4.1.9.9.661.1.3.2.1.3INTEGER {unknown(1), none(2), imsiUnknownInHlr(3), illegalMs(4), imsiUnknownInVlr(5), imeiNotAccepted(6), illegalMe(7), gprsServNotAllowed(8), gprsNonGprsServNotAllow(9), msIdentUnknown(10), implicitlyDetached(11), plmnNotAllowed(12), lacNotAllowed(13), roamingNotAllowed(14), gprsServNotAllowInPlmn(15), noSuitableCellInLa(16), mscTempNotReachable(17), networkFailure(18), macFailure(19), synchFailure(20), congestion(21), gsmAuthenNotAccept(22), servOptionNotSupport(23), reqServOptionNotSub(24), servOptionOutOfOrder(25), callCannotIdentified(26), noPdpContextActivated(27), invalidMandatInfo(28), unpsecProtErr(29)}read-onlycurrent
c3gGsmCurrentService
OBJECT-TYPE
Current service type: unknown(1) - service type is unknown invalid(2) - no service circuitSwitched(3) - circuit switched service packetSwitched(4) - packet switched service combined(5) - combination of circuit and packet switched service
1.3.6.1.4.1.9.9.661.1.3.2.1.4INTEGER {unknown(1), invalid(2), circuitSwitched(3), packetSwitched(4), combined(5)}read-onlycurrent
c3gGsmPacketService
OBJECT-TYPE
Packet Service type: unknown(1) - service type is unknown. none(2) - no service. gprs(3) - General Packet Radio Service (GPRS). edge(4) - Enhanced Data rates for GSM Evolution (EDGE). umtsWcdma(5) - Universal Mobile Telecommunications System (UMTS) / Wideband Code-Division Multiple-Access (W-CDMA). hsdpa(6) - High-Speed Downlink Packet Access (HSDPA) hsdpa(7) - High-Speed Uplink Packet Access (HSUPA) hspa(8) - High-Speed Packet Access (HSPA) hspaPlus(9) - High-Speed Packet Access (HSPA) Plus lte(10) - Long Term Evolution
1.3.6.1.4.1.9.9.661.1.3.2.1.5INTEGER {unknown(1), none(2), gprs(3), edge(4), umtsWcdma(5), hsdpa(6), hsupa(7), hspa(8), hspaPlus(9), lte(10)}read-onlycurrent
c3gGsmCurrentRoamingStatus
OBJECT-TYPE
This object indicates whether the modem is in the home network or is roaming.
1.3.6.1.4.1.9.9.661.1.3.2.1.6INTEGER {unknown(1), roaming(2), home(3)}read-onlycurrent
c3gGsmNetworkSelectionMode
OBJECT-TYPE
Network selection mode. Can be manual selection mode or automatic selection mode. Set to automatic by default.
1.3.6.1.4.1.9.9.661.1.3.2.1.7INTEGER {unknown(1), automatic(2), manual(3)}read-writecurrent
c3gGsmCountry
OBJECT-TYPE
Country code. Country code string is given by the base station.
1.3.6.1.4.1.9.9.661.1.3.2.1.8DisplayString (SIZE(0..64))read-onlycurrent
c3gGsmNetwork
OBJECT-TYPE
Network code. Network Code string is given by the base station.
1.3.6.1.4.1.9.9.661.1.3.2.1.9DisplayString (SIZE(0..64))read-onlycurrent
c3gGsmMcc
OBJECT-TYPE
Mobile Country Code (MCC). Value of '-1' indicates MCC is 'Not Applicable'.
1.3.6.1.4.1.9.9.661.1.3.2.1.10Integer32read-writecurrent
c3gGsmMnc
OBJECT-TYPE
Mobile Network Code (MNC). Value of '-1' indicates MNC is 'Not Applicable'.
1.3.6.1.4.1.9.9.661.1.3.2.1.11Integer32read-writecurrent
c3gGsmRac
OBJECT-TYPE
Routing Area Code (RAC). RAC is given by the base station.
1.3.6.1.4.1.9.9.661.1.3.2.1.12Unsigned32read-onlycurrent
c3gGsmCurrentCellId
OBJECT-TYPE
Cell Identifier of current cell. Cell ID is given by the base station.
1.3.6.1.4.1.9.9.661.1.3.2.1.13Unsigned32read-onlycurrent
c3gGsmCurrentPrimaryScramblingCode
OBJECT-TYPE
Primary scrambling code of current cell. The primary scrambling code is typically identified through symbol-by-symbol correlation over the CPICH (Common Pilot Channel) with all codes within the code group, after the primary scrambling code has been identified, the Primary CCPCH can be detected and the system and cell specific BCH information can be read.
1.3.6.1.4.1.9.9.661.1.3.2.1.14Unsigned32read-onlycurrent
c3gGsmPlmnSelection
OBJECT-TYPE
Public Land Mobile Network (PLMN) selection. Can be manual selection mode or automatic selection mode. Set to automatic by default.
1.3.6.1.4.1.9.9.661.1.3.2.1.15INTEGER {unknown(1), manual(2), automatic(3)}read-writecurrent
c3gGsmRegPlmn
OBJECT-TYPE
Registered PLMN.
1.3.6.1.4.1.9.9.661.1.3.2.1.16DisplayString (SIZE(0..64))read-onlycurrent
c3gGsmPlmnAbbr
OBJECT-TYPE
PLMN abbreviated number.
1.3.6.1.4.1.9.9.661.1.3.2.1.17DisplayString (SIZE(0..64))read-onlycurrent
c3gGsmServiceProvider
OBJECT-TYPE
Service provider.
1.3.6.1.4.1.9.9.661.1.3.2.1.18DisplayString (SIZE(0..64))read-onlycurrent
c3gGsmTotalByteTransmitted
OBJECT-TYPE
Total number of bytes transmitted for all calls. It is the total number of bytes transmitted by modem, not to be confused with the number of bytes transmitted through the interface.
1.3.6.1.4.1.9.9.661.1.3.2.1.19Counter64read-onlycurrent
c3gGsmTotalByteReceived
OBJECT-TYPE
Total number of bytes received for all calls. It is the total number of bytes received by modem, not to be confused with the number of bytes received from the interface.
1.3.6.1.4.1.9.9.661.1.3.2.1.20Counter64read-onlycurrent
c3gGsmPdpProfile
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.661.1.3.3
c3gGsmPdpProfileTable
OBJECT-TYPE
Cellular GSM PDP profiles table. Cellular device contains multiple profile entries which can be used to establish cellular data connections (PDP contexts). Users can choose any of available PDP profiles to establish data connections. Data connections are described in c3gGsmPacketSessionTable. This table is applicable in only 3G technology mode. Refer CISCO-WAN-CELL-EXT-MIB when in 4G-LTE mode.
1.3.6.1.4.1.9.9.661.1.3.3.1not-accessiblecurrent
c3gGsmPdpProfileEntry
OBJECT-TYPE
An entry (conceptual row) in the c3gGsmPdpProfileTable.
1.3.6.1.4.1.9.9.661.1.3.3.1.1not-accessiblecurrent
c3gGsmPdpProfileIndex
OBJECT-TYPE
Profile index, combined with entPhysicalIndex to access profile table.
1.3.6.1.4.1.9.9.661.1.3.3.1.1.1Integer32 (1..1000)not-accessiblecurrent
c3gGsmPdpProfileType
OBJECT-TYPE
This object indicates configured Packet Data Protocol (PDP) type.
1.3.6.1.4.1.9.9.661.1.3.3.1.1.2C3gPdpTyperead-createcurrent
c3gGsmPdpProfileAddr
OBJECT-TYPE
Configured PDP/EPS Bearer address. PDP type is defined in c3gGsmPdpProfileType.
1.3.6.1.4.1.9.9.661.1.3.3.1.1.3DisplayString (SIZE(0..64))read-createcurrent
c3gGsmPdpProfileApn
OBJECT-TYPE
This object indicates profile Access Point Name (APN). This information is provided by the service provider.
1.3.6.1.4.1.9.9.661.1.3.3.1.1.4DisplayString (SIZE(0..64))read-createcurrent
c3gGsmPdpProfileAuthenType
OBJECT-TYPE
This object indicates PDP authentication type supported. CHAP and PAP are supported in GSM. The type of authentication to be used is provided by the service provider.
1.3.6.1.4.1.9.9.661.1.3.3.1.1.5INTEGER {unknown(1), none(2), chap(3), pap(4)}read-createcurrent
c3gGsmPdpProfileUsername
OBJECT-TYPE
This object indicates the username to be used for PDP authentication. This information is provided by the service provider.
1.3.6.1.4.1.9.9.661.1.3.3.1.1.6DisplayString (SIZE(0..64))read-createcurrent
c3gGsmPdpProfilePassword
OBJECT-TYPE
This object indicates the password to be used for PDP authentication. This information is provided by the service provider.
1.3.6.1.4.1.9.9.661.1.3.3.1.1.7DisplayString (SIZE(0..64))read-createcurrent
c3gGsmPdpProfileRowStatus
OBJECT-TYPE
The status of this conceptual row. This object is used to manage creation, modification and deletion of rows in this table.
1.3.6.1.4.1.9.9.661.1.3.3.1.1.8RowStatusread-createcurrent
c3gGsmPacketSessionTable
OBJECT-TYPE
Cellular 3G GSM packet session table. This table is applicable in only 3G technology mode. Refer CISCO-WAN-CELL-EXT-MIB when in 4G-LTE mode.
1.3.6.1.4.1.9.9.661.1.3.3.2not-accessiblecurrent
c3gGsmPacketSessionEntry
OBJECT-TYPE
An entry (conceptual row) in the c3gGsmPacketSessionTable.
1.3.6.1.4.1.9.9.661.1.3.3.2.1not-accessiblecurrent
c3gGsmPacketSessionStatus
OBJECT-TYPE
This object indicates PDP session status of the profile. This is active when the call is established and PDP contextr has become active.
1.3.6.1.4.1.9.9.661.1.3.3.2.1.1INTEGER {unknown(1), active(2), inactive(3)}read-onlycurrent
c3gGsmPdpType
OBJECT-TYPE
This object indicates current session PDP type.
1.3.6.1.4.1.9.9.661.1.3.3.2.1.2C3gPdpTyperead-onlycurrent
c3gGsmPdpAddress
OBJECT-TYPE
Current session PDP context/EPS Bearer address. PDP type is obtained from c3gGsmPdpType.
1.3.6.1.4.1.9.9.661.1.3.3.2.1.3DisplayString (SIZE(0..64))read-onlycurrent
c3gGsmReqUmtsQosTable
OBJECT-TYPE
Requested UMTS QoS parameters table. This table contains UMTS QoS parameters requested by modem to the cellular network via PDP Context Activation Request message. The requested UMTS QoS profile is optional. This table is applicable only in 3G technology mode.
1.3.6.1.4.1.9.9.661.1.3.3.3not-accessiblecurrent
c3gGsmReqUmtsQosEntry
OBJECT-TYPE
An entry (conceptual row) in the c3gGsmReqUmtsQosTable.
1.3.6.1.4.1.9.9.661.1.3.3.3.1not-accessiblecurrent
c3gGsmReqUmtsQosTrafficClass
OBJECT-TYPE
Request UMTS QoS traffic classes.
1.3.6.1.4.1.9.9.661.1.3.3.3.1.2C3gUmtsQosTrafficClassread-createcurrent
c3gGsmReqUmtsQosMaxUpLinkBitRate
OBJECT-TYPE
Request UMTS QoS maximum uplink bit rate.
1.3.6.1.4.1.9.9.661.1.3.3.3.1.3C3gUmtsQosLinkBitRateread-createcurrent
c3gGsmReqUmtsQosMaxDownLinkBitRate
OBJECT-TYPE
Request UMTS QoS maximum downlink bit rate.
1.3.6.1.4.1.9.9.661.1.3.3.3.1.4C3gUmtsQosLinkBitRateread-createcurrent
c3gGsmReqUmtsQosGuaUpLinkBitRate
OBJECT-TYPE
Request UMTS QoS guaranteed uplink bit rate.
1.3.6.1.4.1.9.9.661.1.3.3.3.1.5C3gUmtsQosLinkBitRateread-createcurrent
c3gGsmReqUmtsQosGuaDownLinkBitRate
OBJECT-TYPE
Request UMTS QoS guaranteed downlink bit rate.
1.3.6.1.4.1.9.9.661.1.3.3.3.1.6C3gUmtsQosLinkBitRateread-createcurrent
c3gGsmReqUmtsQosOrder
OBJECT-TYPE
Request UMTS QoS deliver order.
1.3.6.1.4.1.9.9.661.1.3.3.3.1.7C3gUmtsQosOrderread-createcurrent
c3gGsmReqUmtsQosErroneousSdu
OBJECT-TYPE
Request UMTS QoS Delivery of Erroneous SDU.
1.3.6.1.4.1.9.9.661.1.3.3.3.1.8C3gUmtsQosErroneousSduread-createcurrent
c3gGsmReqUmtsQosMaxSduSize
OBJECT-TYPE
Request UMTS QoS maximum SDU size, the valid range is between 1 and 1520 bytes. Value of '0' indicates the maximum SDU size is unspecified.
1.3.6.1.4.1.9.9.661.1.3.3.3.1.9Unsigned32 (0..1520)read-createcurrent
c3gGsmReqUmtsQosSer
OBJECT-TYPE
Request UMTS QoS SDU error ratio.
1.3.6.1.4.1.9.9.661.1.3.3.3.1.10C3gUmtsQosSerread-createcurrent
c3gGsmReqUmtsQosBer
OBJECT-TYPE
Request UMTS QoS residual bit error ratio.
1.3.6.1.4.1.9.9.661.1.3.3.3.1.11C3gUmtsQosBerread-createcurrent
c3gGsmReqUmtsQosDelay
OBJECT-TYPE
Request UMTS QoS transfer delay in ms, the valid range is between 1 and 4000 ms. Value of '0' indicates the QoS delay is unspecified.
1.3.6.1.4.1.9.9.661.1.3.3.3.1.12Unsigned32 (0..4000)read-createcurrent
c3gGsmReqUmtsQosPriority
OBJECT-TYPE
Request UMTS QoS traffic handling priority.
1.3.6.1.4.1.9.9.661.1.3.3.3.1.13C3gUmtsQosPriorityread-createcurrent
c3gGsmReqUmtsQosSrcStatDescriptor
OBJECT-TYPE
Request UMTS QoS source statistics descriptor.
1.3.6.1.4.1.9.9.661.1.3.3.3.1.14C3gUmtsQosSrcStatDescriptorread-createcurrent
c3gGsmReqUmtsQosSignalIndication
OBJECT-TYPE
Request UMTS QoS signalling indication.
1.3.6.1.4.1.9.9.661.1.3.3.3.1.15C3gUmtsQosSignalIndicationread-createcurrent
c3gGsmReqUmtsQosRowStatus
OBJECT-TYPE
The status of this conceptual row. This object is used to manage creation, modification and deletion of rows in this table.
1.3.6.1.4.1.9.9.661.1.3.3.3.1.16RowStatusread-createcurrent
c3gGsmMinUmtsQosTable
OBJECT-TYPE
Minimum acceptable UMTS QoS table. This table contains minimum acceptable UMTS QoS parameters which is checked by the MT (Mobile Termination) against the negotiated profile returned in the Activate PDP Context Accept message. The minimum acceptable UMTS QoS profile is optional. This table is applicable only in 3G technology mode.
1.3.6.1.4.1.9.9.661.1.3.3.4not-accessiblecurrent
c3gGsmMinUmtsQosEntry
OBJECT-TYPE
An entry (conceptual row) in the c3gGsmMinUmtsQosTable.
1.3.6.1.4.1.9.9.661.1.3.3.4.1not-accessiblecurrent
c3gGsmMinUmtsQosTrafficClass
OBJECT-TYPE
Minimum UMTS QoS traffic classes.
1.3.6.1.4.1.9.9.661.1.3.3.4.1.1C3gUmtsQosTrafficClassread-createcurrent
c3gGsmMinUmtsQosMaxUpLinkBitRate
OBJECT-TYPE
Minimum UMTS QoS maximum uplink bit rate.
1.3.6.1.4.1.9.9.661.1.3.3.4.1.2C3gUmtsQosLinkBitRateread-createcurrent
c3gGsmMinUmtsQosMaxDownLinkBitRate
OBJECT-TYPE
Minimum UMTS QoS maximum downlink bit rate.
1.3.6.1.4.1.9.9.661.1.3.3.4.1.3C3gUmtsQosLinkBitRateread-createcurrent
c3gGsmMinUmtsQosGuaUpLinkBitRate
OBJECT-TYPE
Minimum UMTS QoS guaranteed uplink bit rate.
1.3.6.1.4.1.9.9.661.1.3.3.4.1.4C3gUmtsQosLinkBitRateread-createcurrent
c3gGsmMinUmtsQosGuaDownLinkBitRate
OBJECT-TYPE
Minimum UMTS QoS guaranteed downlink bit rate.
1.3.6.1.4.1.9.9.661.1.3.3.4.1.5C3gUmtsQosLinkBitRateread-createcurrent
c3gGsmMinUmtsQosOrder
OBJECT-TYPE
Minimum UMTS QoS deliver order.
1.3.6.1.4.1.9.9.661.1.3.3.4.1.6C3gUmtsQosOrderread-createcurrent
c3gGsmMinUmtsQosErroneousSdu
OBJECT-TYPE
Minimum UMTS QoS Delivery of Erroneous SDU.
1.3.6.1.4.1.9.9.661.1.3.3.4.1.7C3gUmtsQosErroneousSduread-createcurrent
c3gGsmMinUmtsQosMaxSduSize
OBJECT-TYPE
Minimum UMTS maximum SDU size, the valid range is between 1 and 1520 bytes. Value of '0' indicates the maximum SDU size is unspecified.
1.3.6.1.4.1.9.9.661.1.3.3.4.1.8Unsigned32 (0..1520)read-createcurrent
c3gGsmMinUmtsQosSer
OBJECT-TYPE
Minimum UMTS QoS SDU error ratio.
1.3.6.1.4.1.9.9.661.1.3.3.4.1.9C3gUmtsQosSerread-createcurrent
c3gGsmMinUmtsQosBer
OBJECT-TYPE
Minimum UMTS residual bit error ratio.
1.3.6.1.4.1.9.9.661.1.3.3.4.1.10C3gUmtsQosBerread-createcurrent
c3gGsmMinUmtsQosDelay
OBJECT-TYPE
Minimum UMTS transfer delay in ms, the valid range is between 1 and 4000 ms. Value of '0' indicates the QoS delay is unspecified.
1.3.6.1.4.1.9.9.661.1.3.3.4.1.11Unsigned32 (0..4000)read-createcurrent
c3gGsmMinUmtsQosPriority
OBJECT-TYPE
Minimum UMTS QoS traffic handling priority.
1.3.6.1.4.1.9.9.661.1.3.3.4.1.12C3gUmtsQosPriorityread-createcurrent
c3gGsmMinUmtsQosSrcStatDescriptor
OBJECT-TYPE
Minimum UMTS QoS source statistics descriptor.
1.3.6.1.4.1.9.9.661.1.3.3.4.1.13C3gUmtsQosSrcStatDescriptorread-createcurrent
c3gGsmMinUmtsQosSignalIndication
OBJECT-TYPE
Minimum UMTS QoS signalling indication.
1.3.6.1.4.1.9.9.661.1.3.3.4.1.14C3gUmtsQosSignalIndicationread-createcurrent
c3gGsmMinUmtsQosRowStatus
OBJECT-TYPE
The status of this conceptual row. This object is used to manage creation, modification and deletion of rows in this table.
1.3.6.1.4.1.9.9.661.1.3.3.4.1.15RowStatusread-createcurrent
c3gGsmNegoUmtsQosTable
OBJECT-TYPE
Negotiated UMTS QoS table. This table contains negotiated UMTS QoS parameters returned in the Activate PDP Context Accept message. The objects in this table are valid only if the value of object c3gGsmPacketSessionStatus defined in c3gGsmPacketSessionTable is 'active'. This table is applicable only in 3G technology mode.
1.3.6.1.4.1.9.9.661.1.3.3.5not-accessiblecurrent
c3gGsmNegoUmtsQosEntry
OBJECT-TYPE
An entry (conceptual row) in the c3gGsmNegoUmtsQosTable.
1.3.6.1.4.1.9.9.661.1.3.3.5.1not-accessiblecurrent
c3gGsmNegoUmtsQosTrafficClass
OBJECT-TYPE
Negotiated UMTS QoS traffic classes.
1.3.6.1.4.1.9.9.661.1.3.3.5.1.1C3gUmtsQosTrafficClassread-onlycurrent
c3gGsmNegoUmtsQosMaxUpLinkBitRate
OBJECT-TYPE
Negotiated UMTS QoS maximum uplink bit rate.
1.3.6.1.4.1.9.9.661.1.3.3.5.1.2C3gUmtsQosLinkBitRateread-onlycurrent
c3gGsmNegoUmtsQosMaxDownLinkBitRate
OBJECT-TYPE
Negotiated UMTS QoS maximum downlink bit rate.
1.3.6.1.4.1.9.9.661.1.3.3.5.1.3C3gUmtsQosLinkBitRateread-onlycurrent
c3gGsmNegoUmtsQosGuaUpLinkBitRate
OBJECT-TYPE
Negotiated UMTS QoS guaranteed uplink bit rate.
1.3.6.1.4.1.9.9.661.1.3.3.5.1.4C3gUmtsQosLinkBitRateread-onlycurrent
c3gGsmNegoUmtsQosGuaDownLinkBitRate
OBJECT-TYPE
Negotiated UMTS QoS guaranteed downlink bit rate.
1.3.6.1.4.1.9.9.661.1.3.3.5.1.5C3gUmtsQosLinkBitRateread-onlycurrent
c3gGsmNegoUmtsQosOrder
OBJECT-TYPE
Negotiated UMTS QoS deliver order.
1.3.6.1.4.1.9.9.661.1.3.3.5.1.6C3gUmtsQosOrderread-onlycurrent
c3gGsmNegoUmtsQosErroneousSdu
OBJECT-TYPE
Negotiated UMTS QoS Delivery of Erroneous SDU.
1.3.6.1.4.1.9.9.661.1.3.3.5.1.7C3gUmtsQosErroneousSduread-onlycurrent
c3gGsmNegoUmtsQosMaxSduSize
OBJECT-TYPE
Negotiated UMTS QoS maximum SDU size, the valid range is between 1 and 1520 bytes. Value of '0' indicates the maximum SDU size is subscribed.
1.3.6.1.4.1.9.9.661.1.3.3.5.1.8Unsigned32 (0..1520)read-onlycurrent
c3gGsmNegoUmtsQosSer
OBJECT-TYPE
Negotiated UMTS QoS SDU error ratio.
1.3.6.1.4.1.9.9.661.1.3.3.5.1.9C3gUmtsQosSerread-onlycurrent
c3gGsmNegoUmtsQosBer
OBJECT-TYPE
Negotiated UMTS QoS residual bit error ratio.
1.3.6.1.4.1.9.9.661.1.3.3.5.1.10C3gUmtsQosBerread-onlycurrent
c3gGsmNegoUmtsQosDelay
OBJECT-TYPE
Negotiated UMTS QoS transfer delay in ms, the valid range is between 1 and 4000 ms. Value of '0' indicates the QoS delay is subscribed.
1.3.6.1.4.1.9.9.661.1.3.3.5.1.11Unsigned32 (0..4000)read-onlycurrent
c3gGsmNegoUmtsQosPriority
OBJECT-TYPE
Negotiated UMTS QoS traffic handling priority.
1.3.6.1.4.1.9.9.661.1.3.3.5.1.12C3gUmtsQosPriorityread-onlycurrent
c3gGsmNegoUmtsQosSrcStatDescriptor
OBJECT-TYPE
Negotiated UMTS QoS source statistics descriptor.
1.3.6.1.4.1.9.9.661.1.3.3.5.1.13C3gUmtsQosSrcStatDescriptorread-onlycurrent
c3gGsmNegoUmtsQosSignalIndication
OBJECT-TYPE
Negotiated UMTS QoS signalling indication.
1.3.6.1.4.1.9.9.661.1.3.3.5.1.14C3gUmtsQosSignalIndicationread-onlycurrent
c3gGsmReqGprsQosTable
OBJECT-TYPE
Requested GPRS QoS parameters table. This table contains GPRS QoS parameters requested by modem to the cellular network via PDP Context Request message. The requested GPRS QoS profile is optional. This table is applicable only in 3G technology mode.
1.3.6.1.4.1.9.9.661.1.3.3.6not-accessiblecurrent
c3gGsmReqGprsQosEntry
OBJECT-TYPE
An entry (conceptual row) in the c3gGsmReqGprsQosTable.
1.3.6.1.4.1.9.9.661.1.3.3.6.1not-accessiblecurrent
c3gGsmReqGprsQosPrecedence
OBJECT-TYPE
Request GPRS QoS precedence.
1.3.6.1.4.1.9.9.661.1.3.3.6.1.1C3gGprsQosPrecedenceread-createcurrent
c3gGsmReqGprsQosDelay
OBJECT-TYPE
Request GPRS QoS delay classes.
1.3.6.1.4.1.9.9.661.1.3.3.6.1.2C3gGprsQosDelayread-createcurrent
c3gGsmReqGprsQosReliability
OBJECT-TYPE
Request GPRS QoS reliability.
1.3.6.1.4.1.9.9.661.1.3.3.6.1.3C3gGprsQosReliabilityread-createcurrent
c3gGsmReqGprsQosPeakRate
OBJECT-TYPE
Request GPRS QoS peak rate.
1.3.6.1.4.1.9.9.661.1.3.3.6.1.4C3gGprsQosPeakRateread-createcurrent
c3gGsmReqGprsQosMeanRate
OBJECT-TYPE
Request GPRS QoS mean rate.
1.3.6.1.4.1.9.9.661.1.3.3.6.1.5C3gGprsQosMeanRateread-createcurrent
c3gGsmReqGprsQosRowStatus
OBJECT-TYPE
The status of this conceptual row. This object is used to manage creation, modification and deletion of rows in this table.
1.3.6.1.4.1.9.9.661.1.3.3.6.1.6RowStatusread-createcurrent
c3gGsmMinGprsQosTable
OBJECT-TYPE
Minimum acceptable GPRS QoS table. This table contains minimum acceptable GPRS QoS parameters which is checked by the MT (Mobile Termination) against the negotiated profile returned in the Activate PDP Context Accept message. The minimum acceptable GPRS QoS profile is optional. This table is applicable only in 3G technology mode.
1.3.6.1.4.1.9.9.661.1.3.3.7not-accessiblecurrent
c3gGsmMinGprsQosEntry
OBJECT-TYPE
An entry (conceptual row) in the c3gGsmMinGprsQosTable.
1.3.6.1.4.1.9.9.661.1.3.3.7.1not-accessiblecurrent
c3gGsmMinGprsQosPrecedence
OBJECT-TYPE
Minimum GPRS QoS precedence.
1.3.6.1.4.1.9.9.661.1.3.3.7.1.1C3gGprsQosPrecedenceread-createcurrent
c3gGsmMinGprsQosDelay
OBJECT-TYPE
Minimum GPRS QoS delay classes.
1.3.6.1.4.1.9.9.661.1.3.3.7.1.2C3gGprsQosDelayread-createcurrent
c3gGsmMinGprsQosReliability
OBJECT-TYPE
Minimum GPRS QoS reliability.
1.3.6.1.4.1.9.9.661.1.3.3.7.1.3C3gGprsQosReliabilityread-createcurrent
c3gGsmMinGprsQosPeakRate
OBJECT-TYPE
Minimum GPRS QoS peak rate.
1.3.6.1.4.1.9.9.661.1.3.3.7.1.4C3gGprsQosPeakRateread-createcurrent
c3gGsmMinGprsQosMeanRate
OBJECT-TYPE
Minimum GPRS QoS mean rate.
1.3.6.1.4.1.9.9.661.1.3.3.7.1.5C3gGprsQosMeanRateread-createcurrent
c3gGsmMinGprsQosRowStatus
OBJECT-TYPE
The status of this conceptual row. This object is used to manage creation, modification and deletion of rows in this table.
1.3.6.1.4.1.9.9.661.1.3.3.7.1.6RowStatusread-createcurrent
c3gGsmNegoGprsQosTable
OBJECT-TYPE
Negotiated GPRS QoS table. This table contains negotiated GPRS QoS parameters returned in the Activate PDP Context Accept message. The objects in this table are valid only if the value of object c3gGsmPacketSessionStatus defined in c3gGsmPacketSessionTable is 'active'. This table is applicable only in 3G technology mode.
1.3.6.1.4.1.9.9.661.1.3.3.8not-accessiblecurrent
c3gGsmNegoGprsQosEntry
OBJECT-TYPE
An entry (conceptual row) in the c3gGsmNegoGprsQosTable.
1.3.6.1.4.1.9.9.661.1.3.3.8.1not-accessiblecurrent
c3gGsmNegoGprsQosPrecedence
OBJECT-TYPE
Negotiated GPRS QoS precedence.
1.3.6.1.4.1.9.9.661.1.3.3.8.1.1C3gGprsQosPrecedenceread-onlycurrent
c3gGsmNegoGprsQosDelay
OBJECT-TYPE
Negotiated GPRS QoS delay classes.
1.3.6.1.4.1.9.9.661.1.3.3.8.1.2C3gGprsQosDelayread-onlycurrent
c3gGsmNegoGprsQosReliability
OBJECT-TYPE
Negotiated GPRS QoS reliability.
1.3.6.1.4.1.9.9.661.1.3.3.8.1.3C3gGprsQosReliabilityread-onlycurrent
c3gGsmNegoGprsQosPeakRate
OBJECT-TYPE
Negotiated GPRS QoS peak rate.
1.3.6.1.4.1.9.9.661.1.3.3.8.1.4C3gGprsQosPeakRateread-onlycurrent
c3gGsmNegoGprsQosMeanRate
OBJECT-TYPE
Negotiated GPRS QoS mean rate.
1.3.6.1.4.1.9.9.661.1.3.3.8.1.5C3gGprsQosMeanRateread-onlycurrent
c3gGsmRadio
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.661.1.3.4
c3gGsmRadioTable
OBJECT-TYPE
Cellular 3G GSM/4G-LTE radio table.
1.3.6.1.4.1.9.9.661.1.3.4.1not-accessiblecurrent
c3gGsmRadioEntry
OBJECT-TYPE
An entry (conceptual row) in the c3gGsmRadioTable.
1.3.6.1.4.1.9.9.661.1.3.4.1.1not-accessiblecurrent
c3gCurrentGsmRssi
OBJECT-TYPE
The GPRS/UMTS/LTE RSSI value.
1.3.6.1.4.1.9.9.661.1.3.4.1.1.1C3gRssiread-onlycurrent
c3gCurrentGsmEcIo
OBJECT-TYPE
The GPRS, UMTS or LTE Ec/Io value.
1.3.6.1.4.1.9.9.661.1.3.4.1.1.2C3gEcIoread-onlycurrent
c3gGsmCurrentBand
OBJECT-TYPE
GPRS/UMTS/LTE band to which the modem is attached. Refer CISCO-WAN-CELL-EXT-MIB for LTE band number when in LTE mode.
1.3.6.1.4.1.9.9.661.1.3.4.1.1.3INTEGER {unknown(1), invalid(2), none(3), gsm850(4), gsm900(5), gsm1800(6), gsm1900(7), wcdma800(8), wcdma850(9), wcdma1900(10), wcdma2100(11), lteBand(12)}read-onlycurrent
c3gGsmChannelNumber
OBJECT-TYPE
Channel number to which the modem is attached. This is only applicable in 3G technology mode. Refer CISCO-WAN-CELL-EXT-MIB for the LTE uplink and downlink channel values
1.3.6.1.4.1.9.9.661.1.3.4.1.1.4Unsigned32read-onlycurrent
c3gGsmNumberOfNearbyCell
OBJECT-TYPE
This object indicates the current total number of nearby cell in the c3gGsmNearbyCellTable. User can poll this object to get the total number of nearby cell before polling c3gGsmNearbyCellTable.
1.3.6.1.4.1.9.9.661.1.3.4.1.1.5Unsigned32read-onlycurrent
c3gGsmNearbyCellTable
OBJECT-TYPE
Cellular GSM/4G-LTE nearby cell table. Object c3gGsmNumberOfNearbyCell indicates the total number of nearby cell in this table.
1.3.6.1.4.1.9.9.661.1.3.4.2not-accessiblecurrent
c3gGsmNearbyCellEntry
OBJECT-TYPE
An entry (conceptual row) in the c3gGsmNearbyCellTable.
1.3.6.1.4.1.9.9.661.1.3.4.2.1not-accessiblecurrent
c3gGsmNearbyCellIndex
OBJECT-TYPE
Nearby cell index, combined with entPhysicalIndex to access the Nearby cell table c3gGsmNearbyCellTable.
1.3.6.1.4.1.9.9.661.1.3.4.2.1.1Integer32 (1..100)not-accessiblecurrent
c3gGsmNearbyCellPrimaryScramblingCode
OBJECT-TYPE
Nearby cell primary scrambling code.
1.3.6.1.4.1.9.9.661.1.3.4.2.1.2Unsigned32read-onlycurrent
c3gGsmNearbyCellRscp
OBJECT-TYPE
Nearby cell Received Signal Code Power (RSCP).
1.3.6.1.4.1.9.9.661.1.3.4.2.1.3Integer32 (-150..0)read-onlycurrent
c3gGsmNearbyCellEcIoMeasurement
OBJECT-TYPE
Nearby cell Ec/Io measurement.
1.3.6.1.4.1.9.9.661.1.3.4.2.1.4C3gEcIoread-onlycurrent
c3gGsmHistoryTable
OBJECT-TYPE
Cellular 3G GSM/4G-LTE RSSI history table. The history of RSSI are carried in an octet of string. Each octet in the octet string has a value from 0 to 150 and the 255 value is reserved to indicate an uninitialized (Invalid) value. The format of the octet string with n octets is as following: [ octet 0 is latest, octet 1 is latest-1, . . octet n-2 is oldest-1, octet n-1 is oldest ] To convert the provided value into dBm the following formula should be used: dBm = (-1)*value;
1.3.6.1.4.1.9.9.661.1.3.4.3not-accessiblecurrent
c3gGsmHistoryEntry
OBJECT-TYPE
An entry (conceptual row) in the c3gGsmHistoryTable.
1.3.6.1.4.1.9.9.661.1.3.4.3.1not-accessiblecurrent
c3gGsmHistoryRssiPerSecond
OBJECT-TYPE
Per-second RSSI history. This object contains a per-second history of RSSI values for the last 60 seconds.
1.3.6.1.4.1.9.9.661.1.3.4.3.1.1OCTET STRING (SIZE(60))read-onlycurrent
c3gGsmHistoryRssiPerMinute
OBJECT-TYPE
Per-minute weakest RSSI value history. This object contains a per-minute history of weakest RSSI values for the last 60 minutes. The octet in the string is the weakest RSSI value measured in a minute interval.
1.3.6.1.4.1.9.9.661.1.3.4.3.1.2OCTET STRING (SIZE(60))read-onlycurrent
c3gGsmHistoryRssiPerHour
OBJECT-TYPE
Per-hour weakest RSSI value history. This object contains a per-hour history of weakest RSSI values for the last 72 hours. The octet in the string is the weakest RSSI value measured in an hour interval.
1.3.6.1.4.1.9.9.661.1.3.4.3.1.3OCTET STRING (SIZE(72))read-onlycurrent
c3gGsmSecurity
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.661.1.3.5
c3gGsmSecurityTable
OBJECT-TYPE
Cellular 3G GSM/4G-LTE security table.
1.3.6.1.4.1.9.9.661.1.3.5.1not-accessiblecurrent
c3gGsmSecurityEntry
OBJECT-TYPE
An entry (conceptual row) in the c3gGsmSecurityTable.
1.3.6.1.4.1.9.9.661.1.3.5.1.1not-accessiblecurrent
c3gGsmChv1
OBJECT-TYPE
Card Holder Verification 1 (CHV1), if enabled, the PIN will be verified, if disabled, the PIN will not be verified.
1.3.6.1.4.1.9.9.661.1.3.5.1.1.1INTEGER {unknown(1), disabled(2), enabled(3)}read-writecurrent
c3gGsmSimStatus
OBJECT-TYPE
SIM status. Indicates whether the SIM is present or removed from the SIM socket, and its current status.
1.3.6.1.4.1.9.9.661.1.3.5.1.1.2INTEGER {unknown(1), ok(2), notInserted(3), removed(4), initFailure(5), generalFailure(6), locked(7), chv1Blocked(8), chv2Blocked(9), chv1Rejected(10), chv2Rejected(11), mepLocked(12), networkRejected(13)}read-onlycurrent
c3gGsmSimUserOperationRequired
OBJECT-TYPE
If the SIM is protected (for example, because of CHV1 enabled), it will indicate the type of user operation required.
1.3.6.1.4.1.9.9.661.1.3.5.1.1.3INTEGER {unknown(1), none(2), enterChv1(3), enterChv2(4), enterUnblockChv1(5), enterUnblockChv2(6), enterMepCode(7)}read-onlycurrent
c3gGsmNumberOfRetriesRemaining
OBJECT-TYPE
Indicates the number of attempts remaining in case the SIM is locked. If the number of retries becomes zero, the SIM is blocked and becomes unusable.
1.3.6.1.4.1.9.9.661.1.3.5.1.1.4Unsigned32read-onlycurrent
c3gWanLbs
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.661.1.4
c3gWanLbsCommon
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.661.1.4.1
c3gWanLbsCommonTable
OBJECT-TYPE
This table contains information about the Cellular Location Based service feature. This GPS data is provided by the wireless modem upon GPS configuration.
1.3.6.1.4.1.9.9.661.1.4.1.1not-accessiblecurrent
c3gWanLbsCommonEntry
OBJECT-TYPE
This entry contains information about the Cellular Location Based service variables returned by the wireless modem.
1.3.6.1.4.1.9.9.661.1.4.1.1.1not-accessiblecurrent
c3gLbsModeSelected
OBJECT-TYPE
Mode of Location base service selected. unKnown - mode selection unkown standAlone - Standalone mode msBased - MS-Based mode msAssist - MS-Assist mode reserved - reserved for future use
1.3.6.1.4.1.9.9.661.1.4.1.1.1.1INTEGER {unKnown(1), standAlone(2), msBased(3), msAssist(4), reserved(5)}read-onlycurrent
c3gLbsState
OBJECT-TYPE
Location base service state. gpsDisabled - GPS is disabled gpsEnabled - GPS is enabled gpsLocError - GPS encounters error gpsAcquiring - GPS is acquiring fix
1.3.6.1.4.1.9.9.661.1.4.1.1.1.2INTEGER {gpsDisabled(1), gpsAcquiring(2), gpsEnabled(3), gpsLocError(4)}read-onlycurrent
c3gLbsLocFixError
OBJECT-TYPE
Location base service fix error code.
1.3.6.1.4.1.9.9.661.1.4.1.1.1.3INTEGER {offline(1), noService(2), noConnection(3), noData(4), sessionBusy(5), reserved(6), gpsDisabled(7), connectionFailed(8), errorState(9), clientEnded(10), uiEnded(11), networkEnded(12), timeout(13), privacyLevel(14), networkAccessError(15), fixError(16), pdeRejected(17), trafficChannelExited(18), e911(19), serverError(20), staleBSinformation(21), resourceContention(22), authenticationParameterFailed(23), authenticationFailedLocal(24), authenticationFailedNetwork(25), vxLcsAgentAuthFail(26), unknownSystemError(27), unsupportedService(28), subscriptionViolation(29), desiredFixMethodFailed(30), antennaSwitch(31), noTxConfirmationReceived(32), normalEndOfSession(33), noErrorFromNetwork(34), noResourcesLeftOnNetwork(35), positionServerNotAvailable(36), unsupportedProtocolVersion(37), ssmolrErrorSystemFailure(38), ssmolrErrorUnexpectedDataValue(39), ssmolrErrorDataMissing(40), ssmolrErrorFacilityNotSupported(41), ssmolrErrorSsSubscriptionViolation(42), ssmolrErrorPositionMethodFailure(43), ssmolrErrorUndefined(44), smlcTimeout(45), mtGguardTimeExpired(46), additionalAssistanceNeeded(47), noFixError(48)}read-onlycurrent
c3gLbsLatitude
OBJECT-TYPE
Location base service Latitude.
1.3.6.1.4.1.9.9.661.1.4.1.1.1.4SnmpAdminStringread-onlycurrent
c3gLbsLongitude
OBJECT-TYPE
Location base service longitude.
1.3.6.1.4.1.9.9.661.1.4.1.1.1.5SnmpAdminStringread-onlycurrent
c3gLbsTimeStamp
OBJECT-TYPE
Location base service timestamp.
1.3.6.1.4.1.9.9.661.1.4.1.1.1.6SnmpAdminStringread-onlycurrent
c3gLbsLocUncertaintyAngle
OBJECT-TYPE
GPS Uncertainty parameter Angle, in degrees for the Uncertainty info returned by the GPS device while doing a location fix.
1.3.6.1.4.1.9.9.661.1.4.1.1.1.7Unsigned32read-onlycurrent
c3gLbsLocUncertaintyA
OBJECT-TYPE
GPS Uncertainty parameter A, value in meters for the Uncertainty info returned by the GPS device while doing a location fix.
1.3.6.1.4.1.9.9.661.1.4.1.1.1.8Unsigned32read-onlycurrent
c3gLbsLocUncertaintyPos
OBJECT-TYPE
GPS Uncertainty parameter position, value in meters for the Uncertainty info returned by the GPS device while doing a location fix.
1.3.6.1.4.1.9.9.661.1.4.1.1.1.9Unsigned32read-onlycurrent
c3gLbsFixtype
OBJECT-TYPE
The type of location fix in Location Base service. none - default case, while LBS is not enabled. twoDimension - 2D location fix. threeDimension - 3D location fix.
1.3.6.1.4.1.9.9.661.1.4.1.1.1.10INTEGER {none(1), twoDimension(2), threeDimension(3)}read-onlycurrent
c3gLbsHeightValid
OBJECT-TYPE
This object indicates whether the height returned by the GPS device is valid during location fix.
1.3.6.1.4.1.9.9.661.1.4.1.1.1.11TruthValueread-onlycurrent
c3gLbsHeight
OBJECT-TYPE
This object indicates the GPS height parameter returned by the GPS device while performing location fix.
1.3.6.1.4.1.9.9.661.1.4.1.1.1.12Integer32 (-500..500)read-onlycurrent
c3gLbsLocUncertaintyVertical
OBJECT-TYPE
GPS parameter vertical velocity parameter returned by the GPS device while performing location fix.
1.3.6.1.4.1.9.9.661.1.4.1.1.1.13Unsigned32read-onlycurrent
c3gLbsVelocityValid
OBJECT-TYPE
This object indicates whether the Velocity value returned by the GPS device is valid.
1.3.6.1.4.1.9.9.661.1.4.1.1.1.14TruthValueread-onlycurrent
c3gLbsHeading
OBJECT-TYPE
The compass direction toward which the GPS receiver is (or should be) moving.
1.3.6.1.4.1.9.9.661.1.4.1.1.1.15Unsigned32read-onlycurrent
c3gLbsVelocityHorizontal
OBJECT-TYPE
Horizontal Velocity in meters per second the GPS device is heading. This is the value returned by the GPS satellite relative to the last horizontal location of the GPS device. If at Time X satellite sees the location of GPS device is L1 and then at Time Y satellite sees the location is L2 then speed is (L2 - L1) / ( Y - X).
1.3.6.1.4.1.9.9.661.1.4.1.1.1.16Unsigned32read-onlycurrent
c3gLbsVelocityVertical
OBJECT-TYPE
Vertical Velocity in meters per second the GPS device is heading. This is the value returned by the GPS satellite relative to the last vertical location of the GPS device. If at Time X satellite sees the location of GPS device is L1 and then at Time Y satellite sees the location is L2 then speed is (L2 - L1) / ( Y - X).
1.3.6.1.4.1.9.9.661.1.4.1.1.1.17Unsigned32read-onlycurrent
c3gLbsHepe
OBJECT-TYPE
Horizontal Estimated Position Error returned by the GPS satellite for current position of the GPS device.
1.3.6.1.4.1.9.9.661.1.4.1.1.1.18Unsigned32read-onlycurrent
c3gLbsNumSatellites
OBJECT-TYPE
Number of GPS satellites in vision to the modem while GPS tracking is on.
1.3.6.1.4.1.9.9.661.1.4.1.1.1.19Gauge32read-onlycurrent
c3gWanLbsSatelliteInfo
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.661.1.4.2
c3gWanLbsSatelliteInfoTable
OBJECT-TYPE
This table provides information on each satellite that is visible to the modem during the location fix. These satellites guide the device to acquire a 2D or 3D location fix.
1.3.6.1.4.1.9.9.661.1.4.2.1not-accessiblecurrent
c3gWanLbsSatelliteInfoEntry
OBJECT-TYPE
This table provides information about each satellite's elevation, azimuth, Signal to Noise ratio (SNR) and its reference number local to the router.
1.3.6.1.4.1.9.9.661.1.4.2.1.1not-accessiblecurrent
c3gWanLbsSatelliteInfoIndex
OBJECT-TYPE
An index that is assigned to each satellite under a modem and in combination with entPhysicalIndex uniquely identify it. This index is assigned arbitrarily by the engine and is not saved over reboots.
1.3.6.1.4.1.9.9.661.1.4.2.1.1.1Integer32 (1..1000)not-accessiblecurrent
c3gWanLbsSatelliteNumber
OBJECT-TYPE
Each Satellite is assigned a unique number within this device.This object can be used to locate a particular satellite under a modem.
1.3.6.1.4.1.9.9.661.1.4.2.1.1.2Integer32read-onlycurrent
c3gWanLbsSatelliteElevation
OBJECT-TYPE
Angle of Elevation between the GPS antenna pointing direction, directly towards the satellite, and the local horizontal plane. It is the up-down angle
1.3.6.1.4.1.9.9.661.1.4.2.1.1.3Integer32read-onlycurrent
c3gWanLbsSatelliteAzimuth
OBJECT-TYPE
Azimuth of the current satellite in context referenced by the Satellite InfoIndex. Azimuth is the degree of rotation of the satellites dish on its vertical plane.
1.3.6.1.4.1.9.9.661.1.4.2.1.1.4Integer32read-onlycurrent
c3gWanLbsSatelliteInfoSignalNoiseRatio
OBJECT-TYPE
Signal to Noise Ratio(SNR) of received GPS signal. SNR is refered to as the signal strength in GPS standards.
1.3.6.1.4.1.9.9.661.1.4.2.1.1.5Integer32read-onlycurrent
c3gWanLbsSatelliteUsed
OBJECT-TYPE
Is this satellite in line of sight to the modem used in calculating the GPS location?
1.3.6.1.4.1.9.9.661.1.4.2.1.1.6TruthValueread-onlycurrent
c3gWanLbsSatelliteInfoRowStatus
OBJECT-TYPE
The status of this conceptual row. This object is used to manage creation, modification and deletion of rows in this table.
1.3.6.1.4.1.9.9.661.1.4.2.1.1.7RowStatusread-createcurrent
c3gWanSmsCommon
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.661.1.5
c3gWanSms
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.661.1.5.1
c3gSmsCommonTable
OBJECT-TYPE
This table contains Cellular SMS management MIB objects.
1.3.6.1.4.1.9.9.661.1.5.1.1not-accessiblecurrent
c3gSmsCommonEntry
OBJECT-TYPE
An entry contains counters for the SMS messages received, placed, errored and archived on CDMA, GSM or LTE based modems.
1.3.6.1.4.1.9.9.661.1.5.1.1.1not-accessiblecurrent
c3gSmsServiceAvailable
OBJECT-TYPE
This object indicates the availability of SMS Service.
1.3.6.1.4.1.9.9.661.1.5.1.1.1.1TruthValueread-onlycurrent
c3gSmsOutSmsCount
OBJECT-TYPE
Number of SMS messages which have been sent successfully.
1.3.6.1.4.1.9.9.661.1.5.1.1.1.2Counter32read-onlycurrent
c3gSmsOutSmsErrorCount
OBJECT-TYPE
Number of SMS message that could not be sent.
1.3.6.1.4.1.9.9.661.1.5.1.1.1.3Counter32read-onlycurrent
c3gSmsInSmsStorageUsed
OBJECT-TYPE
Number of SMS message records space used in the Incoming SMS message storage. One standard SMS message (cdma or gsm) occupies 1 unit of record storage space. A big SMS message can span 'n' sms record space but still be called as 1 SMS message. Storage used can be greater than or equal to total number of Incoming SMS received.
1.3.6.1.4.1.9.9.661.1.5.1.1.1.4Gauge32read-onlycurrent
c3gSmsInSmsStorageUnused
OBJECT-TYPE
The number of SMS messages record space left unused in the Incoming SMS message storage. This is equal to c3gSmsInSmsStorageMax - c3gSmsInSmsStorageUsed.
1.3.6.1.4.1.9.9.661.1.5.1.1.1.5Gauge32read-onlycurrent
c3gSmsInSmsArchiveCount
OBJECT-TYPE
Number of successful archive of Incoming SMS messages since router reload. Each SMS message occupies x bytes of space. So if the incoming message is huge, then it is archived as multiple of x bytes but still called as one SMS message. This is the difference between c3gSmsInSmsArchiveCount and c3gSmsInSmsArchived.
1.3.6.1.4.1.9.9.661.1.5.1.1.1.6Gauge32read-onlycurrent
c3gSmsInSmsArchiveErrorCount
OBJECT-TYPE
The number of Incoming SMS messages that could not be archived since device was reloaded.
1.3.6.1.4.1.9.9.661.1.5.1.1.1.7Gauge32read-onlycurrent
c3gSmsArchiveUrl
OBJECT-TYPE
URL of the sms archive directory on the ftp server. The url will be of this format ftp://x.y.z.k/user/dirname
1.3.6.1.4.1.9.9.661.1.5.1.1.1.8SnmpAdminStringread-onlycurrent
c3gSmsOutSmsStatus
OBJECT-TYPE
Status of the last send operation of outgoing SMS message to the network.
1.3.6.1.4.1.9.9.661.1.5.1.1.1.9INTEGER {unknown(1), success(2), copySmsHeader(3), copySmsBody(4), sent(5), receivedSentNotification(6), receivedOutMsgNumber(7), receivedOutMsgStatus(8)}read-onlycurrent
c3gSmsInSmsCount
OBJECT-TYPE
Number of SMS messages which have been received successfully and stored in router. These SMS's are a mirror copy of SMS stored in Modem or SIM
1.3.6.1.4.1.9.9.661.1.5.1.1.1.10Counter32read-onlycurrent
c3gSmsInSmsDeleted
OBJECT-TYPE
Number of SMS messages which have been deleted since router boot up. This does not include SMS messages that are already archived.
1.3.6.1.4.1.9.9.661.1.5.1.1.1.11Counter32read-onlycurrent
c3gSmsInSmsStorageMax
OBJECT-TYPE
Number of SMS message records space allocated in the router's DRAM to store Incoming SMS messages.
1.3.6.1.4.1.9.9.661.1.5.1.1.1.12Counter64read-onlycurrent
c3gSmsInSmsCallBack
OBJECT-TYPE
Number of incoming SMS messages that triggered callback.
1.3.6.1.4.1.9.9.661.1.5.1.1.1.13Counter32read-onlycurrent
c3gSmsOutSmsPendingCount
OBJECT-TYPE
Number of outgoing SMS messages that are in pending queue of the router.
1.3.6.1.4.1.9.9.661.1.5.1.1.1.14Gauge32read-onlycurrent
c3gSmsOutSmsArchiveCount
OBJECT-TYPE
Number of successfull archive of outgoing SMS messages since router reload.
1.3.6.1.4.1.9.9.661.1.5.1.1.1.15Gauge32read-onlycurrent
c3gSmsOutSmsArchiveErrorCount
OBJECT-TYPE
Number of failed archive of outgoing SMS messages since router reload.
1.3.6.1.4.1.9.9.661.1.5.1.1.1.16Gauge32read-onlycurrent
c3gSmsInSmsArchived
OBJECT-TYPE
Number of Incoming SMS messages that are successfully archived since router reload.
1.3.6.1.4.1.9.9.661.1.5.1.1.1.17Gauge32read-onlycurrent
ciscoWan3gMIBConform
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.661.2
ciscoWan3gMIBCompliances
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.661.2.1
ciscoWan3gMIBGroups
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.661.2.2

Notifications

NameOIDStatus
c3gModemUpNotif
NOTIFICATION-TYPE
This is the notification that the modem has been detected by host interface. Users can enable or disable the generation of this notification by using object c3gModemUpNotifEnabled.
1.3.6.1.4.1.9.9.661.0.1current
c3gModemDownNotif
NOTIFICATION-TYPE
This is the notification that the modem has not been detected by host interface, or has been disconnected from host interface. Users can enable or disable the generation of this notification by using object c3gModemDownNotifEnabled.
1.3.6.1.4.1.9.9.661.0.2current
c3gServiceChangedNotif
NOTIFICATION-TYPE
Notification for service change event. Objects c3gPreviousServiceType and c3gCurrentServiceType will be included in the notification. Users can enable or disable the generation of this notification by using object c3gServiceChangedNotifEnabled.
1.3.6.1.4.1.9.9.661.0.3current
c3gNetworkChangedNotif
NOTIFICATION-TYPE
Notification for network change event. Objects c3gCurrentSid, c3gCurrentNid, c3gGsmMcc, c3gGsmMnc and c3gRoamingStatus will be included in the notification. Users can enable or disable the generation of this notification by using object c3gNetworkChangedNotifEnabled.
1.3.6.1.4.1.9.9.661.0.4current
c3gConnectionStatusChangedNotif
NOTIFICATION-TYPE
Notification for connection status change event. Objects c3gConnectionStatus and c3gCurrentServiceType will be included in the notification. Users can use object c3gConnectionStatusChangedNotifFlag to control what connection status changes will cause the generation of this notification.
1.3.6.1.4.1.9.9.661.0.5current
c3gRssiOnsetNotif
NOTIFICATION-TYPE
If RSSI goes below c3gRssiOnsetNotifThreshold and the service bit in c3gRssiOnsetNotifFlag is set, this notification will be generated. Object c3gNotifRadioService will indicate which service generates this notification and the associated RSSI will be reported in c3gNotifRssi. Please note that c3gNotifRssi is used to indicate the RSSI value that triggers the notification, user should go to the corresponding radio table to get the current RSSI value.
1.3.6.1.4.1.9.9.661.0.6current
c3gRssiAbateNotif
NOTIFICATION-TYPE
If RSSI goes above c3gRssiAbateNotifThreshold and the service bit in c3gRssiAbateNotifFlag is set, this notification will be generated. Object c3gNotifRadioService will indicate which service generates this notification and the associated RSSI will be reported in c3gNotifRssi. Please note that c3gNotifRssi is used to indicate the RSSI value that triggers the notification, user should go to the corresponding radio table to get the current RSSI value.
1.3.6.1.4.1.9.9.661.0.7current
c3gEcIoOnsetNotif
NOTIFICATION-TYPE
If Ec/Io goes below c3gEcIoOnsetNotifThreshold and the service bit in c3gEcIoOnsetNotifFlag is set, this notification will be generated. Object c3gNotifRadioService will indicate which service generates this notification and the associated Ec/Io will be reported in c3gNotifEcIo. Please note that c3gNotifEcIo is used to indicate the Ec/Io value that triggers the notification, user should go to the corresponding radio table to get the current Ec/Io value.
1.3.6.1.4.1.9.9.661.0.8current
c3gEcIoAbateNotif
NOTIFICATION-TYPE
If Ec/Io goes above c3gEcIoAbateNotifThreshold and the service bit in c3gEcIoAbateNotifFlag is set, this notification will be generated. Object c3gNotifRadioService will indicate which service generates this notification and the associated Ec/Io will be reported in c3gNotifEcIo. Please note that c3gNotifEcIo is used to indicate the Ec/Io value that triggers the notification, user should go to the corresponding radio table to get the current Ec/Io value.
1.3.6.1.4.1.9.9.661.0.9current
c3gModemTemperOnsetNotif
NOTIFICATION-TYPE
If modem temperature goes above c3gModemTemperOnsetNotifThreshold and the value of c3gModemTemperOnsetNotifEnabled is 'true', this notification will be generated and the current value of c3gModemTemperature will be included in this notification.
1.3.6.1.4.1.9.9.661.0.10current
c3gModemTemperAbateNotif
NOTIFICATION-TYPE
If modem temperature goes below c3gModemTemperAbateNotifThreshold and the value of c3gModemTemperAbateNotifEnabled is 'true', this notification will be generated and the current value of c3gModemTemperature will be included in this notification.
1.3.6.1.4.1.9.9.661.0.11current
c3gModemTemperOnsetRecoveryNotif
NOTIFICATION-TYPE
This trap is generated as a recovery notification for c3gModemTemperOnsetNotif.This trap is generated when the current value of c3gModemTemperature goes below c3gModemTemperOnsetNotifThreshold once it has generated the c3gModemTemperOnsetNotif and the value of c3gModemTemperOnsetNotifEnabled is 'true'. c3gModemTemperature contains the current value of modem temperature.
1.3.6.1.4.1.9.9.661.0.12current
c3gModemTemperAbateRecoveryNotif
NOTIFICATION-TYPE
This trap is generated as a recovery notification for c3gModemTemperAbateNotif.This trap is generated when the current value of c3gModemTemperature goes above c3gModemTemperAbateNotifThreshold once it has generated the c3gModemTemperAbateNotif and the value of c3gModemTemperAbateNotifEnabled is 'true' c3gModemTemperature contains the current value of modem temperature
1.3.6.1.4.1.9.9.661.0.13current

Conformance

NameOIDStatus
ciscoWan3gMIBCompliance
MODULE-COMPLIANCE
This is a default module-compliance containing default object groups.
1.3.6.1.4.1.9.9.661.2.1.1deprecated
ciscoWan3gMIBCompliance1
MODULE-COMPLIANCE
The compliance statement for the CISCO-WAN-3G-MIB.
1.3.6.1.4.1.9.9.661.2.1.2deprecated
ciscoWan3gMIBComplianceRev1
MODULE-COMPLIANCE
This is a default module-compliance containing default object groups.
1.3.6.1.4.1.9.9.661.2.1.3current
ciscoWan3gMIBCompliance1Rev1
MODULE-COMPLIANCE
The compliance statement for the CISCO-WAN-3G-MIB.
1.3.6.1.4.1.9.9.661.2.1.4current
ciscoWan3gMIBCommonObjectGroup
OBJECT-GROUP
A collection of common objects for Cellular interface.
1.3.6.1.4.1.9.9.661.2.2.1current
ciscoWan3gMIBCdmaObjectGroup
OBJECT-GROUP
A collection of objects for Cellular 3G CDMA.
1.3.6.1.4.1.9.9.661.2.2.2current
ciscoWan3gMIBGsmObjectGroup
OBJECT-GROUP
A collection of objects for Cellular 3G GSM and LTE.
1.3.6.1.4.1.9.9.661.2.2.3current
ciscoWan3gMIBNotificationGroup
NOTIFICATION-GROUP
A collection of objects for Cellular WAN notifications. ciscoWan3gMIBNotificationGroup object is superseded by ciscoWan3gMIBNotificationGroupRev1.
1.3.6.1.4.1.9.9.661.2.2.4deprecated
ciscoWan3gMIBLbsObjectGroup
OBJECT-GROUP
A collection of common objects for Cellular Location Based Service.
1.3.6.1.4.1.9.9.661.2.2.5current
ciscoWan3gMIBSmsObjectGroup
OBJECT-GROUP
A collection of common objects for Cellular Short Messaging Service.
1.3.6.1.4.1.9.9.661.2.2.6current
ciscoWan3gMIBNotificationGroupRev1
NOTIFICATION-GROUP
A collection of objects for Cellular WAN notifications.
1.3.6.1.4.1.9.9.661.2.2.7current