CISCO-PPPOE-MIB
- Registered at
- 1.3.6.1.4.1.9.9.194
- Last updated
- 2011-04-25 00:00
- Organization
- Cisco Systems, Inc.
- Revisions
- 2011-04-25 00:00, 2005-12-21 00:00, 2001-02-20 00:00
- Namespace
- cisco
- Source file
CISCO-PPPOE-MIB- Digest
sha256:856baa5079705b45b5d570e44c794e823b7e7fdada0fc2e1a713ec7e61148c65
Description
Cisco PPPoE sessions management MIB Module.
Contact
Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-ppp@cisco.com
Imports
| From | Symbols |
|---|---|
| ATM-MIB | atmVclEntry, atmVclVci, atmVclVpi |
| ATM-TC-MIB | AtmVcIdentifier, AtmVpIdentifier |
| CISCO-QOS-PIB-MIB | Percent |
| CISCO-SMI | ciscoMgmt |
| IF-MIB | ifDescr, ifIndex |
| Q-BRIDGE-MIB | VlanId, VlanIndex |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP |
| SNMPv2-SMI | Counter32, Gauge32, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, Unsigned32, iso |
| SNMPv2-TC | DisplayString, MacAddress, TEXTUAL-CONVENTION, TruthValue |
Imported by
Nothing in this corpus imports this module.
Load order
Every file a consumer needs in order to load this module, dependencies first.
ATM-MIB ATM-TC-MIB BRIDGE-MIB CISCO-PPPOE-MIB CISCO-QOS-PIB-MIB CISCO-SMI IANAifType-MIB IF-MIB P-BRIDGE-MIB Q-BRIDGE-MIB RFC1158-MIB RFC1271-MIB RMON-MIB RMON2-MIB SNMP-FRAMEWORK-MIB SNMPv2-CONF SNMPv2-MIB SNMPv2-SMI SNMPv2-TC TOKEN-RING-RMON-MIB
Objects
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| ciscoPppoeMIBObjects OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.194.1 | |||
| cPppoeSystemSessionInfo OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.194.1.1 | |||
| cPppoeSystemCurrSessions OBJECT-TYPE The current number of active PPPoE sessions within this system. | 1.3.6.1.4.1.9.9.194.1.1.1 | Gauge32 | read-only | current |
| cPppoeSystemHighWaterSessions OBJECT-TYPE The high water mark of the established PPPoE sessions since the system was initialized. | 1.3.6.1.4.1.9.9.194.1.1.2 | Gauge32 | read-only | current |
| cPppoeSystemMaxAllowedSessions OBJECT-TYPE Maximum number of allowed PPPoE sessions within the system. | 1.3.6.1.4.1.9.9.194.1.1.3 | Unsigned32 | read-write | current |
| cPppoeSystemThresholdSessions OBJECT-TYPE Threshold value of the established PPPoE sessions within the system. Default value is equal to cPppoeSystemMaxSessionsConfigurable | 1.3.6.1.4.1.9.9.194.1.1.4 | Unsigned32 | read-write | current |
| cPppoeSystemExceededSessionErrors OBJECT-TYPE The accumulated number of errors for establishing PPPoE session in the system due to the cPppoeSystemCurrSessions value exceeds the cPppoeSystemMaxAllowedSessions value. | 1.3.6.1.4.1.9.9.194.1.1.5 | Counter32 | read-only | current |
| cPppoeSystemPerMacSessionlimit OBJECT-TYPE This object provides limit on number of PPPoE sessions for a single client Ethernet MAC address. If the limit is reached new session request from the client would be denied | 1.3.6.1.4.1.9.9.194.1.1.6 | Unsigned32 | read-write | current |
| cPppoeSystemPerMacIWFSessionlimit OBJECT-TYPE This object provides limit on number of PPPoE sessions with interworking flag(IWF) enabled, from a single client MAC address. If the limit is reached new session request would be denied. | 1.3.6.1.4.1.9.9.194.1.1.7 | Unsigned32 | read-write | current |
| cPppoeSystemPerMacThrottleRatelimit OBJECT-TYPE This object provides the rate limit at which PPPoE session were created from a single client MAC address. During a configured time interval, once the number of new session requests coming from a particular client MAC address reaches this limit, it's expected to have delay in response for those clients. | 1.3.6.1.4.1.9.9.194.1.1.8 | Unsigned32 | read-write | current |
| cPppoeSystemPerVLANlimit OBJECT-TYPE This object provides limit on number of PPPoE sessions on a particular Vlan. If the limit is reached new session request on this vlan would be denied. | 1.3.6.1.4.1.9.9.194.1.1.9 | Unsigned32 | read-write | current |
| cPppoeSystemPerVLANthrottleRatelimit OBJECT-TYPE This object provides the rate limit at which PPPoE session were created on a Vlan. During a configured time interval once the number of new session requests coming on a particular Vlan reaches this limit, it's expected to have delay in response for client on this Vlan. | 1.3.6.1.4.1.9.9.194.1.1.10 | Unsigned32 | read-write | current |
| cPppoeSystemPerVClimit OBJECT-TYPE This object provides limit on number of PPPoE sessions on a particular ATM-VC. If the limit is reached new session request on this VC would be denied. | 1.3.6.1.4.1.9.9.194.1.1.11 | Unsigned32 | read-write | current |
| cPppoeSystemPerVCThrottleRatelimit OBJECT-TYPE This object provides the rate limit at which PPPoE session were created on an ATM-VC. During a configured time interval, once the number of new session requests coming on an ATM-VC reaches this limit, it's expected to have delay in response for those clients on this VC. | 1.3.6.1.4.1.9.9.194.1.1.12 | Unsigned32 | read-write | current |
| cPppoeSystemSessionLossThreshold OBJECT-TYPE This object is used to monitor number of active PPPoE sessions above a healthy watermark. If number of PPPoE sessions falls below this watermark then we can expect something wrong happened. So we send out trap to user indicating session loss below watermark. | 1.3.6.1.4.1.9.9.194.1.1.13 | Unsigned32 | read-write | current |
| cPppoeSystemSessionLossPercent OBJECT-TYPE This object is used to monitor the percentage of PPPoE sessions going down at a configured time interval. During a time interval if percentage of PPPoE sessions lost, falls above this object value, we send trap indicating loss of sessions above percentage expected. | 1.3.6.1.4.1.9.9.194.1.1.14 | Percent | read-write | current |
| cPppoeVcCfgInfo OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.194.1.2 | |||
| cPppoeVcCfgTable OBJECT-TYPE The table contains the PPPoE protocol related configuration for the VCLs(ATM Interface Virtual Channel Link). | 1.3.6.1.4.1.9.9.194.1.2.1 | not-accessible | current | |
| cPppoeVcCfgEntry OBJECT-TYPE An entry containing additional PPPoE protocol configuration related management information applicable to a particular VCL. | 1.3.6.1.4.1.9.9.194.1.2.1.1 | not-accessible | current | |
| cPppoeVcEnable OBJECT-TYPE This object specifies whether the PPPoE protocol should be enabled for this VCL. If the value of this object is `false`, PPPoE protocol is disabled; otherwise the PPPoE protocol is enabled. | 1.3.6.1.4.1.9.9.194.1.2.1.1.1 | TruthValue | read-write | current |
| cPppoeVcSessionsInfo OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.194.1.3 | |||
| cPppoeVcSessionsTable OBJECT-TYPE Table of configuration and statistics about the number of PPPoE sessions on a list of VCLs(ATM Interface Virtual Channel Link). | 1.3.6.1.4.1.9.9.194.1.3.1 | not-accessible | current | |
| cPppoeVcSessionsEntry OBJECT-TYPE An entry in the table containing PPPoE session related information on a VCL. The entry of this table is created when the value of cPppoeVcEnable object is set to `true` for the entry associated VCL. The entry of this table is deleted when the of cPppoeVcEnable object set to `false` or the entry associated VCL is deleted from atmVclTable. | 1.3.6.1.4.1.9.9.194.1.3.1.1 | not-accessible | current | |
| cPppoeVcCurrSessions OBJECT-TYPE The current number of active PPPoE sessions on the VCL. | 1.3.6.1.4.1.9.9.194.1.3.1.1.1 | Gauge32 | read-only | current |
| cPppoeVcHighWaterSessions OBJECT-TYPE The high water mark of the established PPPoE sessions on the VCL. | 1.3.6.1.4.1.9.9.194.1.3.1.1.2 | Gauge32 | read-only | current |
| cPppoeVcMaxAllowedSessions OBJECT-TYPE The maximum number of allowed PPPoE sessions on the VCL. | 1.3.6.1.4.1.9.9.194.1.3.1.1.3 | Unsigned32 | read-write | current |
| cPppoeVcThresholdSessions OBJECT-TYPE The Threshold value of the established PPPoE sessions on the VCL. Default value is equal to cPppoeVcMaxAllowedSessions. | 1.3.6.1.4.1.9.9.194.1.3.1.1.4 | Unsigned32 | read-write | current |
| cPppoeVcExceededSessionErrors OBJECT-TYPE The accumulated number of errors for establishing PPPoE session in the VC due to the cPppoeVcCurrSessions value exceeds the cPppoeVcMaxAllowedSessions value. | 1.3.6.1.4.1.9.9.194.1.3.1.1.5 | Counter32 | read-only | current |
| cPppoeSessionsPerInterfaceInfo OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.194.1.4 | |||
| cPppoeSessionsPerInterfaceTable OBJECT-TYPE A list of interfaces' PPPoE session information. | 1.3.6.1.4.1.9.9.194.1.4.1 | not-accessible | current | |
| cPppoeSessionsPerInterfaceEntry OBJECT-TYPE An entry in the table containing PPPoE sessions information such as count information of various states like PPP Termination Aggregation(PTA), Forwarded(FWDED), Transient (TRANS) and TOTAL count and the configured loss threshold per given physical interface | 1.3.6.1.4.1.9.9.194.1.4.1.1 | not-accessible | current | |
| cPppoeTotalSessions OBJECT-TYPE The total number of PPPoE sessions which includes PPP Termination Aggregation(PTA), Forwarded(FWDED) and Transient(TRANS) state on a physical interface. | 1.3.6.1.4.1.9.9.194.1.4.1.1.1 | Gauge32 | read-only | current |
| cPppoePtaSessions OBJECT-TYPE Number of PPPoE sessions which are in PPP Termination Aggregation(PTA) state on a particular physical interface. | 1.3.6.1.4.1.9.9.194.1.4.1.1.2 | Gauge32 | read-only | current |
| cPppoeFwdedSessions OBJECT-TYPE Number of PPPoE sessions which are in Forwarded(FWDED) state on a particular physical interface. | 1.3.6.1.4.1.9.9.194.1.4.1.1.3 | Gauge32 | read-only | current |
| cPppoeTransSessions OBJECT-TYPE Number of PPPoE sessions which are in Transient(TRANS) state on a particular physical interface. | 1.3.6.1.4.1.9.9.194.1.4.1.1.4 | Gauge32 | read-only | current |
| cPppoePerInterfaceSessionLossThreshold OBJECT-TYPE This object is used to monitor number of active PPPoE sessions, initiated from a particular physical interface. The sssion count is accumulation of all the pppoe session came on a physical and its sub-interfaces. If this count drops below this object water mark, we expect some problem and send out trap indicating drop of sessions below watermark. | 1.3.6.1.4.1.9.9.194.1.4.1.1.5 | Unsigned32 | read-only | current |
| cPppoePerInterfaceSessionLossPercent OBJECT-TYPE This object is used to monitor the percentage of PPPoE sessions loss on a particular physical interface including all of its sub-interfaces. If during a configured interval of time, percentage of PPPoE sessions lost on a physical interface is above this object value we send a trap. | 1.3.6.1.4.1.9.9.194.1.4.1.1.6 | Unsigned32 | read-only | current |
| cPppoeSystemSessionNotifyObjects OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.194.1.5 | |||
| cPppoeSystemSessionClientMacAddress OBJECT-TYPE The client MAC address that is referred as a part of the notification information. Example: cPppoeSystemSessionPerMACLimitNotif | 1.3.6.1.4.1.9.9.194.1.5.1 | MacAddress | accessible-for-notify | current |
| cPppoeSystemSessionVlanID OBJECT-TYPE The Vlan ID of PPPoE session that is referred as a part of the notification information. Example: cPppoeSystemSessionPerVLANLimitNotif | 1.3.6.1.4.1.9.9.194.1.5.2 | VlanId | accessible-for-notify | current |
| cPppoeSystemSessionInnerVlanID OBJECT-TYPE The inner Vlan ID of PPPoE QinQ session that is referred as a part of the notification information. Example: cPppoeSystemSessionPerVLANLimitNotif | 1.3.6.1.4.1.9.9.194.1.5.3 | VlanIndex | accessible-for-notify | current |
| cPppoeSystemSessionVci OBJECT-TYPE The ATM VCI of PPPoE session that is referred as a part of the notification information. Example:cPppoeSystemSessionPerVCLimitTrap | 1.3.6.1.4.1.9.9.194.1.5.4 | AtmVcIdentifier | accessible-for-notify | current |
| cPppoeSystemSessionVpi OBJECT-TYPE The ATM VPI of PPPoE session that is referred as a part of the notification information. Example: cPppoeSystemSessionPerVCLimitTrap | 1.3.6.1.4.1.9.9.194.1.5.5 | AtmVpIdentifier | accessible-for-notify | current |
| ciscoPppoeMIBNotificationPrefix OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.194.2 | |||
| ciscoPppoeMIBNotification OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.194.2.0 | |||
| ciscoPppoeMIBConformance OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.194.3 | |||
| ciscoPppoeMIBCompliances OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.194.3.1 | |||
| ciscoPppoeMIBGroups OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.194.3.2 |
Notifications
| Name | OID | Status |
|---|---|---|
| cPppoeSystemSessionThresholdTrap NOTIFICATION-TYPE A notification indicating that number of active sessions on the system exceeded system sessions threshold value. System sessions threshold value is indicated by cPppoeSystemThresholdSessions. An agent must not generate more than one cPppoeSessionThresholdTrap `trap-event` in a 30 second period, where a `trap-event` is the transmission of a single trap PDU to a list of trap destinations. If additional `the number of PPPoE sessions exceeds threshold` condition occur within the 30 second `throttling` period, then these trap-events should be suppressed by the agent. An NMS should periodically check the value of cPppoeCurrSessions to detect any missed cPppoeVcSessionThresholdTrap trap-events, e.g. due to throttling or transmission loss. Where 30 is the `throttling` period of trap-event. | 1.3.6.1.4.1.9.9.194.2.0.1 | current |
| cPppoeVcSessionThresholdTrap NOTIFICATION-TYPE A notification indicating that number of active sessions on the VC exceeded vc sessions threshold value. VC sessions threshold value is indicated by cPppoeVcThresholdSessions. An agent must not generate more than one cPppoeVcSessionThresholdTrap `trap-event` in a 30 second period, where a `trap-event` is the transmission of a single trap PDU to a list of trap destinations. If additional `the number of PPPoE sessions exceeds threshold` condition occur within the 30 second `throttling` period, then these trap-events should be suppressed by the agent. An NMS should periodically check the value of cPppoeVcCurrSessions to detect any missed cPppoeVcSessionThresholdTrap trap-events, e.g. due to throttling or transmission loss. Where 30 is the `throttling` period of trap-event. | 1.3.6.1.4.1.9.9.194.2.0.2 | current |
| cPppoeSystemSessionPerMACLimitNotif NOTIFICATION-TYPE A notification indicating that number of active session from a particular client Ethernet MAC address has reached the configured per MAC limit. There won't be any more session possible from this client MAC address. An agent must not generate more than one cPppoeSystemSessionPerMACLimitNotif `trap-event` in a 30 second period, where a `trap-event` is the transmission of a single trap PDU to a list of trap destinations. If additional `the number of PPPoE MAC sessions exceeds the allowed limit` condition occur within the 30 second `throttling` period, then these trap-events should be suppressed by the agent. | 1.3.6.1.4.1.9.9.194.2.0.3 | current |
| cPppoeSystemSessionPerMACThrottleNotif NOTIFICATION-TYPE A notification indicating that the number of new PPPoE session requests coming in over a configured time interval, from a particular client Ethernet MAC address, has crossed rate limit cPppoeSystemPerMacThrottleRatelimit. The client MAC address on which this event happened is referred through object cPppoeSystemSessionClientMacAddress An agent should generate single cPppoeSystemSessionPerMACThrottleNotif trap for configured time interval. | 1.3.6.1.4.1.9.9.194.2.0.4 | current |
| cPppoeSystemSessionPerVLANLimitNotif NOTIFICATION-TYPE A notification indicating that number of active session on a Vlan has reached the maximum limit. There won't be any new PPPoE session possible on this Vlan. The maximum limit can be referred through object cPppoeSystemPerVLANlimit. The Vlan ID of vlan can be referred though object cPppoeSystemSessionVlanID. If Vlan is QinQ, cPppoeSystemSessionInnerVlanID refers the inner Vlan id. In case the vlan is not QinQ cPppoeSystemSessionInnerVlanID will be zero. The interface details can be referred through ifDescr object. An agent must not generate more than one cPppoeSystemSessionPerVLANLimitNotif `trap-event` in a 30 second period, where a `trap-event` is the transmission of a single trap PDU to a list of trap destinations. If additional `the number of PPPoE sessions on this Vlan exceeds the allowed limit` condition occur within the 30 second `throttling` period, then these trap-events should be suppressed by the agent. | 1.3.6.1.4.1.9.9.194.2.0.5 | current |
| cPppoeSystemSessionPerVLANThrottleNotif NOTIFICATION-TYPE A notification indicating that the number of new PPPoE session request coming on a particular Vlan, over a configured time interval has reached rate limit. The rate limit is referred through object cPppoeSystemPerVLANthrottleRatelimit. The Vlan ID of vlan can be referred though object cPppoeSystemSessionVlanID. If Vlan is QinQ, cPppoeSystemSessionInnerVlanID refers the inner Vlan Id. In case the vlan is not QinQ cPppoeSystemSessionInnerVlanID will be zero. The interface details can be referred through ifDescr object. An agent should generate single cPppoeSystemSessionPerVLANThrottleNotif trap for the configured time interval | 1.3.6.1.4.1.9.9.194.2.0.6 | current |
| cPppoeSystemSessionPerVCLimitNotif NOTIFICATION-TYPE A notification indicating that number of active sessions for a ATM VCI/VPI has crossed the configured maximum limit. No more session would be possible on this VC interface. The maximum limit can be referred through object cPppoeSystemPerVClimit, The ATM VC details are referred via objects cPppoeSystemSessionVci, and cPppoeSystemSessionVpi. The Interface details can be referred via ifDescr object. An agent must not generate more than one cPppoeSystemSessionPerVCLimitTrap `trap-event` in a 30 second period, where a `trap-event` is the transmission of a single trap PDU to a list of trap destinations. If additional `the number of PPPoE sessions on this VC exceeds the allowed limit` condition occur within the 30 second `throttling` period, then these trap-events should be suppressed by the agent. | 1.3.6.1.4.1.9.9.194.2.0.7 | current |
| cPppoeSystemSessionPerVCThrottleNotif NOTIFICATION-TYPE A notification indicating that the number of new PPPoE session request coming on a particular ATM VC, over a configured time interval has reached rate limit. The rate limit referred is referred through object cPppoeSystemPerVLANthrottleRatelimit. The ATM VC details are referred via objects cPppoeSystemSessionVci and cPppoeSystemSessionVpi. The Interface details can be referred via ifDescr object. An agent should generate single cPppoeSystemSessionPerVLANThrottleNotif trap for the configured time interval | 1.3.6.1.4.1.9.9.194.2.0.8 | current |
| cPppoeSystemSessionLossThresholdNotif NOTIFICATION-TYPE A notification indicating that number of PPPoE session count dropped below configured global threshold watermark. There will be only one trap send whenever count drops, further low count won't generate trap. Number of PPPoE sessions count need to cross the watermark and drop below watermark to generate trap again. The configured watermark can be referred through object cPppoeSystemSessionLossThreshold. An agent must not generate more than one cPppoeSystemSessionLossThresholdTrap `trap-event` in a 30 second period, where a `trap-event` is the transmission of a single trap PDU to a list of trap destinations. If the PPPoE session count keep on fluctuating around the watermark during 30 seconds, then these trap-events should be suppressed by agent. | 1.3.6.1.4.1.9.9.194.2.0.9 | current |
| cPppoePerInterfaceSessionLossThresholdNotif NOTIFICATION-TYPE A notification indicating that number of PPPoE session initiated via a particular interface has dropped below the configured value for that interface. The interface details can be referred via ifDescr object, and the configured watermark can be referred through cPppoePerInterfaceSessionLossThreshold object. There will be only one trap send whenever count drops, further low count won't generate trap. Number of PPPoE sessions count need to cross the watermark and drop below watermark to generate trap again. An agent must not generate more than one cPppoePerInterfaceSessionLossThresholdTrap `trap-event` in a 30 second period, where a `trap-event` is the transmission of a single trap PDU to a list of trap destinations. If the PPPoE session count keep on fluctuating around the watermark during 30 seconds, then these trap-events should be suppressed by agent. | 1.3.6.1.4.1.9.9.194.2.0.10 | current |
| cPppoeSystemSessionLossPercentNotif NOTIFICATION-TYPE A notification indicating that percentage of PPPoE session lost globally over a duration of time has crossed the configured threshold. The configured percentage water mark can be referred through cPppoeSystemSessionLossPercent object. | 1.3.6.1.4.1.9.9.194.2.0.11 | current |
| cPppoePerInterfaceSessionLossPercentNotif NOTIFICATION-TYPE A notification indicating that percentage of PPPoE sessions lost has crossed configured threshold value for a particular interface. The interface details can be referred through ifDescr object, and the configured threshold for the interface can be referred through cPppoePerInterfaceSessionLossPercent. | 1.3.6.1.4.1.9.9.194.2.0.12 | current |
Conformance
| Name | OID | Status |
|---|---|---|
| ciscoPppoeMIBBasicCompliance MODULE-COMPLIANCE The compliance statement for entities which implement the Cisco Basic PPPoE MIB. | 1.3.6.1.4.1.9.9.194.3.1.1 | deprecated |
| ciscoPppoeMIBBasicComplianceRev1 MODULE-COMPLIANCE The compliance statement for entities which implement the Cisco Basic PPPoE MIB. | 1.3.6.1.4.1.9.9.194.3.1.2 | current |
| cPppoeSystemGroup OBJECT-GROUP A collection of objects providing information about the PPPoE sessions on a system. | 1.3.6.1.4.1.9.9.194.3.2.1 | current |
| cPppoeVcCfgGroup OBJECT-GROUP A collection of objects specifying PPPoE protocol related configuration on the VCL. | 1.3.6.1.4.1.9.9.194.3.2.2 | current |
| cPppoeVcSessionsGroup OBJECT-GROUP A collection of objects providing information about the number of sessions on the VCL. | 1.3.6.1.4.1.9.9.194.3.2.3 | current |
| cPppoeNotificationsGroup NOTIFICATION-GROUP The collection of notifications used to indicate high PPPoE session volume information(e.g, the number of current PPPoE sessions exceeds threshold setting for the system or a VCL). | 1.3.6.1.4.1.9.9.194.3.2.4 | current |
| cPppoePerInterfaceGroup OBJECT-GROUP A collection of objects providing PPPoE per-interface session state counts and configured threshold informations. | 1.3.6.1.4.1.9.9.194.3.2.5 | current |
| cPppoeSystemLimitsThresholdsGroup OBJECT-GROUP A collection of objects providing the session limit or throttling configuration. There are various Limitation we can impose on PPPoE Sessions it may be limit based on client-MAC or VLAN When ever the limitation is crossed we send out traps. | 1.3.6.1.4.1.9.9.194.3.2.6 | current |
| cPppoeSystemLimitsThresholdsNotifObjectsGroup OBJECT-GROUP This group is collection of notify objects which are used to carry notify information along with certain traps which implements Session restriction such as limit or throttling. | 1.3.6.1.4.1.9.9.194.3.2.7 | current |
| cPppoeSystemLimitsThresholdsNotifGroup NOTIFICATION-GROUP This group is collection of notify objects used to send traps on various session restriction crossed. | 1.3.6.1.4.1.9.9.194.3.2.8 | current |