CISCO-OPTICAL-OTS-MIB
- Registered at
- 1.3.6.1.4.1.9.9.834
- Last updated
- 2026-02-10 00:00
- Organization
- Cisco Systems, Inc.
- Revisions
- 2026-02-10 00:00, 2023-08-02 00:00, 2023-01-31 00:00, 2022-12-09 00:00, 2022-11-10 00:00, 2022-09-22 00:00, 2022-09-07 00:00, 2022-08-24 00:00, 2020-04-08 00:00, 2018-06-06 00:00, 2016-12-16 00:00, 2016-12-09 00:00
- Namespace
- cisco
- Source file
CISCO-OPTICAL-OTS-MIB- Digest
sha256:6a529a58138f5380fe48347ead131db7810f78bcff8cf6519c9c79cea93b2098
Description
This MIB module defines the managed objects and statistics objects for physical layer characteristics of optical line systems and optical transport devices. Performance monitoring (PM) parameters are used to gather, store, set thresholds for and report performance data for early detection of problems. Thresholds are used to set error levels for each PM parameter. During the accumulation cycle, if the current value of a performance monitoring parameter reaches or exceeds its corresponding threshold value, a threshold crossing alarm (TCA) is generated. The TCAs provide early detection of performance degradation. Glossary: OTS : Optical Transmission Section OTS-OCH : Optical Channel Information on OTS ATTN : Optical Attenuation GAIN : Optical Amplifier Gain TILT : Optical Amplifier TILT LBC : Laser Bias Current OSRI : Optical Safety Remote Interlock TX : Transmit RX : Receive VOA : Variable Optical Attenuator dB : Decibel dBm : Decibel-milliwatt mW : Milliwatt nm : Nanometer.
Contact
Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-ncs1001@cisco.com
Imports
| From | Symbols |
|---|---|
| CISCO-OPTICAL-MIB | CoiIntervalType, CoiOptAlarmServiceAffecting, CoiOptAlarmSeverity, CoiOptAlarmStatus, CoiOptAlarmType, CoiOpticalPower, CoiOpticalWavelength |
| CISCO-SMI | ciscoMgmt |
| IF-MIB | ifIndex, ifName |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP |
| SNMPv2-SMI | Integer32, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, Unsigned32, iso |
| SNMPv2-TC | DisplayString, TEXTUAL-CONVENTION, TimeStamp, TruthValue |
Imported by
Nothing in this corpus imports this module.
Load order
Every file a consumer needs in order to load this module, dependencies first.
CISCO-OPTICAL-MIB CISCO-OPTICAL-OTS-MIB CISCO-SMI IANAifType-MIB IF-MIB SNMP-FRAMEWORK-MIB SNMPv2-CONF SNMPv2-MIB SNMPv2-SMI SNMPv2-TC
Textual conventions
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| CiscoOpticalOts2IEGainInDb TEXTUAL-CONVENTION OTS ports associated with an amplifier device. This value represents the amplifier both Ingress and Egress gain setting. The gain is expressed in 1/10ths of a dB. A value of 0 indicates that the amplifier is switched off. Example: A value of 120 represents a gain level of 12.0 dB. | current | |||
| CiscoOpticalOtsAdminState TEXTUAL-CONVENTION This value indicates the controller status. Valid values are - up(1) : controller admin up down(2) : controller admin down | current | |||
| CiscoOpticalOtsAmpliControlMode TEXTUAL-CONVENTION OTS ports associated to amplifier device, this value indicates how the amplifier is controlled. Valid values are - manual(1) : manual control mode (An external entity has to provide gain/tilt settings) auto(2) : automatic control mode (An internal will provide gain/tilt calculation based on power setpoint) power(3) : power control mode (An internal will provide gain/tilt calculation based on power mode settings | current | |||
| CiscoOpticalOtsAmpliGainRange TEXTUAL-CONVENTION OTS ports associated to amplifier device, this value indicates the working ranges available for amplifier gain. Valid values are - normal(1) : normal gain range extended(2) : extended gain range | current | |||
| CiscoOpticalOtsAmpliSafetyCtrlMode TEXTUAL-CONVENTION OTS ports associated to amplifier device, this value indicates how the safety compliaces regulation are statisfied. Valid values are - auto(1) : automatic safety control mode disabled(2) : disabled safety control mode | current | |||
| CiscoOpticalOtsBrRatioInDb TEXTUAL-CONVENTION An integer value that represents BR Ratio in dB. Example: The value -4500 represents a BR Ratio of -45.00 dB. | current | |||
| CiscoOpticalOtsGainInDb TEXTUAL-CONVENTION OTS ports associated to amplifier device,this value represent the amplifier gain setting. An integer value that represents the gain level in 1/100ths of dB. A negative value represents not meaninful value in case the amplifier is switched off for any reason. Example: The value 800 represents an gain level of 8.0 dB. | current | |||
| CiscoOpticalOtsIEGainInDb TEXTUAL-CONVENTION OTS ports associated to amplifier device,this value represent the amplifier gain setting for Ingress and Egress Amplifiers. An integer value that represents the gain level in 1/10ths of dB. A negative value indicates that the amplifier is switched off for any reason. Example: The value 80 represents an gain level of 8.0 dB. | current | |||
| CiscoOpticalOtsIETiltInDb TEXTUAL-CONVENTION This value represents the tilt parameter for an OTS port associated to the amplifier device. An integer value that represents the tilt level in 1/10ths of dB. Example: The value 30 represents a tilt level of 3.0 dB. | current | |||
| CiscoOpticalOtsLaserStatus TEXTUAL-CONVENTION This value indicates the module laser status. Valid values are - unknown(1) : unknown status on(2) : laser on off(3) : laser off apr(4) : Denotes Automatic Power Reduction (APR) | current | |||
| CiscoOpticalOtsOsri TEXTUAL-CONVENTION OTS ports associated to amplifier device, this value indicates the optical safety remote interlock (OSRI) status. Valid values are - on(1) : force laser shutdown for safety interlock off(2) : normal operation | current | |||
| CiscoOpticalOtsPortType TEXTUAL-CONVENTION This value indicates the port type for optical OTS interface. Valid values are - line(1) : port facing the fiber and far-end section. com(2) : port facing the near-end section. osc(3) : port for optical service channel signal. comCheck(4) : com monitoring port for near-end safety usage. working(5) : physical working port if device protection. protected(6) : physical protected port if device protection. | current | |||
| CiscoOpticalOtsProtectionPortRole TEXTUAL-CONVENTION This value indicates the actual OTS port role in case a protection device is in place. Valid values are - active(1) : active port standby(2) : standby port | current | |||
| CiscoOpticalOtsState TEXTUAL-CONVENTION This value indicates the controller status. Valid values are - up(1) : controller operstatus up down(2) : controller operstatus down adminDown(3) : controller administratively down | current | |||
| CiscoOpticalOtsTemperature TEXTUAL-CONVENTION An integer value that represents Temperature in Celsius for OTS controllers. Example: The value 4500 represents a Temperature 45.00 C. | current | |||
| CiscoOpticalOtsTiltInDb TEXTUAL-CONVENTION OTS ports associated to amplifier device, this values represent the tilt parameter. An integer value that represents the tilt level in 1/100ths of dB. Example: The value 300 represents a tilt level of 3.0 dB. | current | |||
| CiscoOpticalOtsTranspAdminState TEXTUAL-CONVENTION This value indicates the transport administrative status. Valid values are - inService(1) : transport administrative status in-service outOfService(2) : transport administrative status out-of-service maintenance(3) : transport administrative status maintenance ains(4) : transport administrative status automatic in-service | current | |||
| CiscoOpticalOtsVoaAttenInDb TEXTUAL-CONVENTION An unsigned integer value that represents the VOA attenuation level in 1/100ths of dB. Example: The value 200 represents an attenuation level of 2.0 dB. | current | |||
| CiscoOpticalOtsVoltage TEXTUAL-CONVENTION An integer value that represents Voltage for OTS controller. Example: The value 350 represents a Voltage 3.50 V. | current |
Objects
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| ciscoOpticalOtsMIBNotifs OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.834.0 | |||
| ciscoOpticalOtsMIBObjects OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.834.1 | |||
| cooOtsController OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.834.1.1 | |||
| cooOtsNotifEnabled OBJECT-TYPE This object controls the generation of cooOtsStatusChange notification. If the value of this object is 'true', then the generation of cooOtsStatusChange notification is enabled. If the value of this object is 'false', then the generation of cooOtsStatusChange notification is disabled. | 1.3.6.1.4.1.9.9.834.1.1.1 | TruthValue | read-write | current |
| cooOtsControllerTable OBJECT-TYPE This table provides management information for OTS optical layer related attributes of interfaces with an ifType of opticalTransport(196). | 1.3.6.1.4.1.9.9.834.1.1.2 | not-accessible | current | |
| cooOtsControllerEntry OBJECT-TYPE An entry containing management information on OTS optical layer related attributes of interfaces with an ifType opticalTrasnport(196). Entries are created by the feature when a new interface is added to the ifTable. | 1.3.6.1.4.1.9.9.834.1.1.2.1 | not-accessible | current | |
| cooOtsControllerPortType OBJECT-TYPE This object represents the port type of the optical OTS interface. | 1.3.6.1.4.1.9.9.834.1.1.2.1.1 | CiscoOpticalOtsPortType | read-only | current |
| cooOtsControllerLaserStatus OBJECT-TYPE This object represents the current operational state of the laser. | 1.3.6.1.4.1.9.9.834.1.1.2.1.2 | CiscoOpticalOtsLaserStatus | read-only | current |
| cooOtsControllerRXPower OBJECT-TYPE This object represents the receive power in 1/100 dBm on optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.2.1.3 | CoiOpticalPower | read-only | current |
| cooOtsControllerTXPower OBJECT-TYPE This object represents the transmit power in 1/100 dBm on optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.2.1.4 | CoiOpticalPower | read-only | current |
| cooOtsControllerAmpliGain OBJECT-TYPE This object represents the amplifier gain value in 1/100 dB on optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.2.1.5 | CiscoOpticalOtsGainInDb | read-write | current |
| cooOtsControllerAmpliTilt OBJECT-TYPE This object represents the amplifier tilt value in 1/100 dB on optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.2.1.6 | CiscoOpticalOtsTiltInDb | read-write | current |
| cooOtsControllerTotalRXPower OBJECT-TYPE This object is used to represents the total receive power in 1/100 dBm on optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.2.1.7 | CoiOpticalPower | read-only | current |
| cooOtsControllerTotalTXPower OBJECT-TYPE This object is used to represents the total transmit power in 1/100 dBm on optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.2.1.8 | CoiOpticalPower | read-only | current |
| cooOtsControllerRXVoaAttenuation OBJECT-TYPE This object represents the receive VOA attenuation value in 1/100 dB on optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.2.1.9 | CiscoOpticalOtsVoaAttenInDb | read-write | current |
| cooOtsControllerTXVoaAttenuation OBJECT-TYPE This object represents the transmit VOA attenuation value in 1/100 dB on optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.2.1.10 | CiscoOpticalOtsVoaAttenInDb | read-write | current |
| cooOtsControllerRXLowThreshold OBJECT-TYPE This object is used to configure the receive low threshold in 1/100 dBm on optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.2.1.11 | CoiOpticalPower | read-write | current |
| cooOtsControllerTXLowThreshold OBJECT-TYPE This object is used to configure the transmit low threshold in 1/100 dBm on optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.2.1.12 | CoiOpticalPower | read-write | current |
| cooOtsControllerAmpliChannelPwr OBJECT-TYPE This object is used to configure the amplifier channel power in 1/100 dBm on optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.2.1.13 | CoiOpticalPower | read-write | current |
| cooOtsControllerChannelPwrMaxDelta OBJECT-TYPE This object is used to configure the maximum delta on channel power in 1/100 dBm on optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.2.1.14 | CoiOpticalPower | read-write | current |
| cooOtsControllerAmpliControlMode OBJECT-TYPE This object is used to configure the amplifier control mode. | 1.3.6.1.4.1.9.9.834.1.1.2.1.15 | CiscoOpticalOtsAmpliControlMode | read-write | current |
| cooOtsControllerAmpliGainRange OBJECT-TYPE This object is used to configure the amplifier gain range. | 1.3.6.1.4.1.9.9.834.1.1.2.1.16 | CiscoOpticalOtsAmpliGainRange | read-write | current |
| cooOtsControllerAmpliSafetyCtrlMode OBJECT-TYPE This object is used to configure the safety control mode. | 1.3.6.1.4.1.9.9.834.1.1.2.1.17 | CiscoOpticalOtsAmpliSafetyCtrlMode | read-write | current |
| cooOtsControllerOsri OBJECT-TYPE This object is used to configure the OSRI. | 1.3.6.1.4.1.9.9.834.1.1.2.1.18 | CiscoOpticalOtsOsri | read-write | current |
| cooOtsControllerProtectionPortRole OBJECT-TYPE This object represents the port role on optical channel interfaces. | 1.3.6.1.4.1.9.9.834.1.1.2.1.19 | CiscoOpticalOtsProtectionPortRole | read-only | current |
| cooOtsControllerState OBJECT-TYPE This object represents the controller status of optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.2.1.20 | CiscoOpticalOtsState | read-only | current |
| cooOtsControllerTranspAdminState OBJECT-TYPE This object represents the transport administration status on optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.2.1.21 | CiscoOpticalOtsTranspAdminState | read-only | current |
| cooOtsControllerAlarmState OBJECT-TYPE This object indicates the current alarms status of the Optics layer. Alarms description : noDefect : No alarms highRXPwr : Input optical power reading over the fail-high threshold highTXPwr : Output optical power reading over the fail-high threshold lowRXPwr : Input optical power reading below the fail-low threshold lowTXPwr : Output optical power reading below the fail-low threshold lospRXPwr : Loss of optical power signal locRXPwr : Loss of optical continuity degLowGain : Amplifier gain degrade low degHighGain : Amplifier gain degrade high alsAmp : Amplifier automatic laser shutdown for safety reason aprAmp : Amplifier automatic power reduction noEqAutoAmp : Channels power not equalized for amplifier automatic control mode misAutoAmp : Misconfiguration for amplifier automatic control mode switchToProtect : Protected port switching to active role autoAmpliCtrlRunning : Amplifier automatic control mode algorithm running | 1.3.6.1.4.1.9.9.834.1.1.2.1.22 | Bits {noDefect(0), highRXPwr(1), highTXPwr(2), lowRXPwr(3), lowTXPwr(4), lospRXPwr(5), locRXPwr(6), degLowGain(7), degHighGain(8), alsAmp(9), aprAmp(10), noEqAutoAmp(11), misAutoAmp(12), switchToProtect(13), autoAmpliCtrlRunning(14)} | read-only | current |
| cooOtsControllerRXSpanLoss OBJECT-TYPE This object is used to represents the span loss power in 1/100 dB on optical OTS interfaces | 1.3.6.1.4.1.9.9.834.1.1.2.1.23 | CoiOpticalPower (-4000..3000) | read-only | current |
| cooOtsControllerTXSpanLoss OBJECT-TYPE This object is used to represents the span loss power in 1/100 dB on optical OTS interfaces | 1.3.6.1.4.1.9.9.834.1.1.2.1.24 | CoiOpticalPower (-4000..3000) | read-only | current |
| cooOtsControllerRXEnabled OBJECT-TYPE This object represents the RX direction status of optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.2.1.25 | TruthValue | read-write | current |
| cooOtsControllerTXEnabled OBJECT-TYPE This object represents the TX direction status of optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.2.1.26 | TruthValue | read-write | current |
| cooOtsControllerIAmpliGain OBJECT-TYPE This object represents the amplifier gain value in 1/10 dB on optical OTS interfaces for ingress direction. | 1.3.6.1.4.1.9.9.834.1.1.2.1.27 | CiscoOpticalOtsIEGainInDb | read-only | current |
| cooOtsControllerIAmpliTilt OBJECT-TYPE This object represents the amplifier tilt value in 1/10 dB on optical OTS interfaces for ingress direction. | 1.3.6.1.4.1.9.9.834.1.1.2.1.28 | CiscoOpticalOtsIETiltInDb | read-only | current |
| cooOtsControllerIAmpliGainRange OBJECT-TYPE This object is used to configure Ingress amplifier gain range. | 1.3.6.1.4.1.9.9.834.1.1.2.1.29 | CiscoOpticalOtsAmpliGainRange | read-only | current |
| cooOtsControllerISafetyControlMode OBJECT-TYPE This object is used to configure Ingress safety control mode. | 1.3.6.1.4.1.9.9.834.1.1.2.1.30 | CiscoOpticalOtsAmpliSafetyCtrlMode | read-only | current |
| cooOtsControllerIAmpliOsri OBJECT-TYPE This object is used to configure Ingress OSRI. | 1.3.6.1.4.1.9.9.834.1.1.2.1.31 | CiscoOpticalOtsOsri | read-only | current |
| cooOtsControllerEAmpliGain OBJECT-TYPE This object represents the amplifier gain value in 1/10 dB on optical OTS interfaces for Egress direction. | 1.3.6.1.4.1.9.9.834.1.1.2.1.32 | CiscoOpticalOtsIEGainInDb | read-write | current |
| cooOtsControllerEAmpliTilt OBJECT-TYPE This object represents the amplifier tilt value in 1/10 dB on optical OTS interfaces for egress direction. | 1.3.6.1.4.1.9.9.834.1.1.2.1.33 | CiscoOpticalOtsIETiltInDb | read-only | current |
| cooOtsControllerEAmpliGainRange OBJECT-TYPE This object is used to configure the Egress amplifier gain range. | 1.3.6.1.4.1.9.9.834.1.1.2.1.34 | CiscoOpticalOtsAmpliGainRange | read-only | current |
| cooOtsControllerESafetyControlMode OBJECT-TYPE This object is used to configure Egress safety control mode. | 1.3.6.1.4.1.9.9.834.1.1.2.1.35 | CiscoOpticalOtsAmpliSafetyCtrlMode | read-write | current |
| cooOtsControllerEAmpliOsri OBJECT-TYPE This object is used to configure Egress OSRI. | 1.3.6.1.4.1.9.9.834.1.1.2.1.36 | CiscoOpticalOtsOsri | read-write | current |
| cooOtsControllerTotLCTXPower OBJECT-TYPE This object represents the transmit power(C+L) in 1/100 dBm on optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.2.1.37 | CoiOpticalPower | read-only | current |
| cooOtsControllerTotLCRXPower OBJECT-TYPE This object represents the receive power(C+L) in 1/100 dBm on optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.2.1.38 | CoiOpticalPower | read-only | current |
| cooOtsControllerIForceApr OBJECT-TYPE This object represents Force Automatic Power Reduction for OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.2.1.39 | INTEGER {off(0), on(1)} | read-only | current |
| cooOtsControllerEForceApr OBJECT-TYPE This object represents Force Automatic Power Reduction for OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.2.1.40 | INTEGER {off(0), on(1)} | read-only | current |
| cooOtsControllerBrPower OBJECT-TYPE This object represents the BR power in 1/100 dBm on optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.2.1.41 | CoiOpticalPower | read-only | current |
| cooOtsControllerLedState OBJECT-TYPE This object represents LED state for OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.2.1.42 | INTEGER {off(0), greenOn(1), greenFlashing(2), yellowOn(3), yellowFlashing(4), redOn(5), redFlashing(6), na(7)} | read-only | current |
| cooOtsControllerEAmpliBrRatio OBJECT-TYPE This object represents EgressAmpliBrRatio for OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.2.1.43 | CiscoOpticalOtsBrRatioInDb | read-only | current |
| cooOtsControllerAmpliControlModeConfigVal OBJECT-TYPE This object represents the Configured Amplifier Control Mode Value for OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.2.1.44 | CiscoOpticalOtsAmpliControlMode | read-write | current |
| cooOtsControllerEAmpliPowerConfigVal OBJECT-TYPE This object represents the Configured Egress Amplifier Power Value in 1/100 dBm on optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.2.1.45 | CoiOpticalPower | read-write | current |
| cooOtsControllerTemperature OBJECT-TYPE This object represents the Controller Temperature in 1/100 C on optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.2.1.46 | CiscoOpticalOtsTemperature | read-only | current |
| cooOtsControllerVoltage OBJECT-TYPE This object represents the Controller Temperature in 1/100 V on optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.2.1.47 | CiscoOpticalOtsVoltage | read-only | current |
| cooOtsControllerEAmpliBrPower OBJECT-TYPE This object represents EgressAmpliBrPower for OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.2.1.48 | CoiOpticalPower | read-only | current |
| cooOtsOchControllerTable OBJECT-TYPE This table provides management information for OTS-OCH optical layer related attributes of interfaces with an ifType of opticalTransport(196). | 1.3.6.1.4.1.9.9.834.1.1.3 | not-accessible | current | |
| cooOtsOchControllerEntry OBJECT-TYPE An entry containing management information on OTS-OCH optical layer related attributes of interfaces with an ifType opticalTransport(196). Entries are created by the feature when a new interface is added to the ifTable. | 1.3.6.1.4.1.9.9.834.1.1.3.1 | not-accessible | current | |
| cooOtsOchControllerPortType OBJECT-TYPE This object represents the port type of the optical OTS-OCH interface. | 1.3.6.1.4.1.9.9.834.1.1.3.1.1 | CiscoOpticalOtsPortType | read-only | current |
| cooOtsOchControllerLaserStatus OBJECT-TYPE This object represents the current operational state of the laser. | 1.3.6.1.4.1.9.9.834.1.1.3.1.2 | CiscoOpticalOtsLaserStatus | read-only | current |
| cooOtsOchControllerRXPower OBJECT-TYPE This object represents the receive power in 1/100 dBm on optical OTS-OCH interfaces. | 1.3.6.1.4.1.9.9.834.1.1.3.1.3 | CoiOpticalPower | read-only | current |
| cooOtsOchControllerTXPower OBJECT-TYPE This object represents the transmit power in 1/100 dBm on optical OTS-OCH interfaces. | 1.3.6.1.4.1.9.9.834.1.1.3.1.4 | CoiOpticalPower | read-only | current |
| cooOtsOchControllerRXLowThreshold OBJECT-TYPE This object is used to configure the receive low threshold in 1/100 dBm on optical OTS-OCH interfaces. | 1.3.6.1.4.1.9.9.834.1.1.3.1.5 | CoiOpticalPower | read-write | current |
| cooOtsOchControllerTXLowThreshold OBJECT-TYPE This object is used to configure the transmit low threshold in 1/100 dBm on optical OTS-OCH interfaces. | 1.3.6.1.4.1.9.9.834.1.1.3.1.6 | CoiOpticalPower | read-write | current |
| cooOtsOchControllerWavelength OBJECT-TYPE This object represents the wavelength on optical OTS-OCH interfaces (unit 1/100 nm). | 1.3.6.1.4.1.9.9.834.1.1.3.1.7 | CoiOpticalWavelength | read-only | current |
| cooOtsOchControllerFrequency OBJECT-TYPE This object represents the frequency on optical Ots-Och channel interfaces (unit 100 MHz). | 1.3.6.1.4.1.9.9.834.1.1.3.1.8 | Unsigned32 (1913500..1961000) | read-only | current |
| cooOtsOchControllerChannelNumber OBJECT-TYPE This object represents the channel number on optical OTS-OCH interfaces. | 1.3.6.1.4.1.9.9.834.1.1.3.1.9 | Unsigned32 (1..384) | read-only | current |
| cooOtsOchControllerState OBJECT-TYPE This object represents the controller status of optical OTS-OCH interfaces. | 1.3.6.1.4.1.9.9.834.1.1.3.1.10 | CiscoOpticalOtsState | read-only | current |
| cooOtsOchControllerTranspAdminState OBJECT-TYPE This object represents the transport administration status on optical OTS-OCH interfaces. | 1.3.6.1.4.1.9.9.834.1.1.3.1.11 | CiscoOpticalOtsTranspAdminState | read-only | current |
| cooOtsOchControllerAlarmState OBJECT-TYPE This object indicates the current alarms status of the Optics layer. Alarms description : noDefect : No alarms highRXPwr : Input optical power reading over the fail-high threshold highTXPwr : Output optical power reading over the fail-high threshold lowRXPwr : Input optical power reading below the fail-low threshold lowTXPwr : Output optical power reading below the fail-low threshold lospRXPwr : Loss of optical power signal locRXPwr : Loss of optical continuity degLowGain : Amplifier gain degrade low degHighGain : Amplifier gain degrade high alsAmp : Amplifier automatic laser shutdown for safety reason aprAmp : Amplifier automatic power reduction noEqAutoAmp : Channels power not equalized for amplifier automatic control mode misAutoAmp : Misconfiguration for amplifier automatic control mode switchToProtect : Protected port switching to active role | 1.3.6.1.4.1.9.9.834.1.1.3.1.12 | Bits {noDefect(0), highRXPwr(1), highTXPwr(2), lowRXPwr(3), lowTXPwr(4), lospRXPwr(5), locRXPwr(6), degLowGain(7), degHighGain(8), alsAmp(9), aprAmp(10), noEqAutoAmp(11), misAutoAmp(12), switchToProtect(13)} | read-only | current |
| cooOtsOchControllerWidth OBJECT-TYPE This object represents the frequency on optical Ots-Och channel interfaces (unit 1/10 GHz). | 1.3.6.1.4.1.9.9.834.1.1.3.1.13 | Unsigned32 (500..8000) | read-only | current |
| cooOtsOchNotifEnabled OBJECT-TYPE This object controls the generation of cooOtsOchStatusChange notification. If the value of this object is 'true', then the generation of cooOtsOchStatusChange notification is enabled. If the value of this object is 'false', then the generation of cooOtsOchStatusChange notification is disabled. | 1.3.6.1.4.1.9.9.834.1.1.4 | TruthValue | read-write | current |
| cooOtsRamanTable OBJECT-TYPE This table provides raman information for optical layer related attributes of interfaces with an ifType of opticalTransport(196). | 1.3.6.1.4.1.9.9.834.1.1.5 | not-accessible | current | |
| cooOtsRamanEntry OBJECT-TYPE An entry containing raman information on optical layer related attributes of interfaces with an ifType opticalTransport(196). Entries are created by the feature when a new interface is added to the ifTable. | 1.3.6.1.4.1.9.9.834.1.1.5.1 | not-accessible | current | |
| cooOtsRaman1TXPower OBJECT-TYPE This object represents the Power of Raman Pump Instance 1 for OTS interfaces (unit 1/100 mW). | 1.3.6.1.4.1.9.9.834.1.1.5.1.1 | CoiOpticalPower | read-only | current |
| cooOtsRaman2TXPower OBJECT-TYPE This object represents the Power of Raman Pump Instance 2 for OTS interfaces (unit 1/100 mW). | 1.3.6.1.4.1.9.9.834.1.1.5.1.2 | CoiOpticalPower | read-only | current |
| cooOtsRaman3TXPower OBJECT-TYPE This object represents the Power of Raman Pump Instance 3 for OTS interfaces (unit 1/100 mW). | 1.3.6.1.4.1.9.9.834.1.1.5.1.3 | CoiOpticalPower | read-only | current |
| cooOtsRaman4TXPower OBJECT-TYPE This object represents the Power of Raman Pump Instance 4 for OTS interfaces (unit 1/100 mW). | 1.3.6.1.4.1.9.9.834.1.1.5.1.4 | CoiOpticalPower | read-only | current |
| cooOtsRaman5TXPower OBJECT-TYPE This object represents the Power of Raman Pump Instance 5 for OTS interfaces (unit 1/100 mW). | 1.3.6.1.4.1.9.9.834.1.1.5.1.5 | CoiOpticalPower | read-only | current |
| cooOtsRaman1Wavelength OBJECT-TYPE This object represents the wavelength of Raman Pump Instance 1 for OTS interfaces (unit 1/100 nm). | 1.3.6.1.4.1.9.9.834.1.1.5.1.6 | CoiOpticalWavelength | read-only | current |
| cooOtsRaman2Wavelength OBJECT-TYPE This object represents the wavelength of Raman Pump Instance 2 for OTS interfaces (unit 1/100 nm). | 1.3.6.1.4.1.9.9.834.1.1.5.1.7 | CoiOpticalWavelength | read-only | current |
| cooOtsRaman3Wavelength OBJECT-TYPE This object represents the wavelength of Raman Pump Instance 3 for OTS interfaces (unit 1/100 nm). | 1.3.6.1.4.1.9.9.834.1.1.5.1.8 | CoiOpticalWavelength | read-only | current |
| cooOtsRaman4Wavelength OBJECT-TYPE This object represents the wavelength of Raman Pump Instance 4 for OTS interfaces (unit 1/100 nm). | 1.3.6.1.4.1.9.9.834.1.1.5.1.9 | CoiOpticalWavelength | read-only | current |
| cooOtsRaman5Wavelength OBJECT-TYPE This object represnts the wavelength of Raman Pump Instance 5 for OTS interfaces (unit 1/100 nm). | 1.3.6.1.4.1.9.9.834.1.1.5.1.10 | CoiOpticalWavelength | read-only | current |
| cooOtsRamanCompositePower OBJECT-TYPE This object represents the Composite Power of Raman Pump for OTS interfaces (unit 1/100 mW). | 1.3.6.1.4.1.9.9.834.1.1.5.1.11 | CoiOpticalPower | read-only | current |
| cooOtsRamanOsri OBJECT-TYPE This object represents the Raman Osri for OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.5.1.12 | CiscoOpticalOtsOsri | read-only | current |
| cooOtsRamanSafetyControlMode OBJECT-TYPE This object represent the Raman Safety Control Mode for OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.5.1.13 | CiscoOpticalOtsAmpliSafetyCtrlMode | read-only | current |
| cooOtsRamanForceAPR OBJECT-TYPE This object represents the Raman Force APR for OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.5.1.14 | INTEGER {off(0), on(1)} | read-only | current |
| cooOtsRamanBRPower OBJECT-TYPE This object represents the Raman Br Power for OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.5.1.15 | CoiOpticalPower | read-only | current |
| cooOtsRamanBRRatio OBJECT-TYPE This object represents the Raman BR Ratio for OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.5.1.16 | CiscoOpticalOtsBrRatioInDb | read-only | current |
| cooOtsControllerTransceiverTable OBJECT-TYPE This table provides ots transceiver detail for optical layer related attributes of interfaces with an ifType of opticalTransport(196). | 1.3.6.1.4.1.9.9.834.1.1.6 | not-accessible | current | |
| cooOtsControllerTransceiverEntry OBJECT-TYPE An entry containing ots transceiver detail on optical layer related attributes of interfaces with an ifType opticalTransport(196). Entries are created by the feature when a new interface is added to the ifTable. | 1.3.6.1.4.1.9.9.834.1.1.6.1 | not-accessible | current | |
| cooOtsControllerTransceiverVendorInfo OBJECT-TYPE This object represents the Controller Vendor Information on optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.6.1.1 | DisplayString | read-only | current |
| cooOtsController2Table OBJECT-TYPE This table provides management information for OTS optical layer related attributes of interfaces with an ifType of opticalTransport(196). DESIGN RATIONALE: This table supersedes the earlier cooOtsControllerTable which used only ifIndex as the INDEX. The previous design could not distinguish between LINE and COM port attributes on the same physical interface (e.g., different TX power, gain settings per port). The composite INDEX structure { ifIndex, cooOtsController2PortType } was introduced to support multi-port OLS modules where LINE and COM ports share an ifIndex but require independent operational data. | 1.3.6.1.4.1.9.9.834.1.1.7 | not-accessible | current | |
| cooOtsController2Entry OBJECT-TYPE An entry containing management information on OTS optical layer related attributes of interfaces with an ifType opticalTransport(196). Entries are created by the feature when a new interface is added to the ifTable. | 1.3.6.1.4.1.9.9.834.1.1.7.1 | not-accessible | current | |
| cooOtsController2PortType OBJECT-TYPE This object represents the port type of the optical OTS interface. | 1.3.6.1.4.1.9.9.834.1.1.7.1.1 | CiscoOpticalOtsPortType | not-accessible | current |
| cooOtsController2LaserStatus OBJECT-TYPE This object represents the current operational state of the laser. | 1.3.6.1.4.1.9.9.834.1.1.7.1.2 | CiscoOpticalOtsLaserStatus | read-only | current |
| cooOtsController2RXPower OBJECT-TYPE This object represents the receive power in 1/100 dBm on optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.7.1.3 | CoiOpticalPower | read-only | current |
| cooOtsController2TXPower OBJECT-TYPE This object represents the transmit power in 1/100 dBm on optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.7.1.4 | CoiOpticalPower | read-only | current |
| cooOtsController2AmpliGain OBJECT-TYPE This object represents the amplifier gain value in 1/100 dB on optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.7.1.5 | CiscoOpticalOtsGainInDb | read-write | current |
| cooOtsController2AmpliTilt OBJECT-TYPE This object represents the amplifier tilt value in 1/100 dB on optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.7.1.6 | CiscoOpticalOtsTiltInDb | read-write | current |
| cooOtsController2TotalRXPower OBJECT-TYPE This object is used to represents the total receive power in 1/100 dBm on optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.7.1.7 | CoiOpticalPower | read-only | current |
| cooOtsController2TotalTXPower OBJECT-TYPE This object is used to represents the total transmit power in 1/100 dBm on optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.7.1.8 | CoiOpticalPower | read-only | current |
| cooOtsController2RXVoaAttenuation OBJECT-TYPE This object represents the receive VOA attenuation value in 1/100 dB on optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.7.1.9 | CiscoOpticalOtsVoaAttenInDb | read-write | current |
| cooOtsController2TXVoaAttenuation OBJECT-TYPE This object represents the transmit VOA attenuation value in 1/100 dB on optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.7.1.10 | CiscoOpticalOtsVoaAttenInDb | read-write | current |
| cooOtsController2RXLowThreshold OBJECT-TYPE This object is used to configure the receive low threshold in 1/100 dBm on optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.7.1.11 | CoiOpticalPower | read-write | current |
| cooOtsController2TXLowThreshold OBJECT-TYPE This object is used to configure the transmit low threshold in 1/100 dBm on optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.7.1.12 | CoiOpticalPower | read-write | current |
| cooOtsController2AmpliChannelPwr OBJECT-TYPE This object is used to configure the amplifier channel power in 1/100 dBm on optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.7.1.13 | CoiOpticalPower | read-write | current |
| cooOtsController2ChannelPwrMaxDelta OBJECT-TYPE This object is used to configure the maximum delta on channel power in 1/100 dBm on optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.7.1.14 | CoiOpticalPower | read-write | current |
| cooOtsController2AmpliControlMode OBJECT-TYPE This object represents the amplifier control mode. | 1.3.6.1.4.1.9.9.834.1.1.7.1.15 | CiscoOpticalOtsAmpliControlMode | read-only | current |
| cooOtsController2AmpliGainRange OBJECT-TYPE This object is used to configure the amplifier gain range. | 1.3.6.1.4.1.9.9.834.1.1.7.1.16 | CiscoOpticalOtsAmpliGainRange | read-write | current |
| cooOtsController2AmpliSafetyCtrlMode OBJECT-TYPE This object is used to configure the safety control mode. | 1.3.6.1.4.1.9.9.834.1.1.7.1.17 | CiscoOpticalOtsAmpliSafetyCtrlMode | read-write | current |
| cooOtsController2Osri OBJECT-TYPE This object is used to configure the OSRI. | 1.3.6.1.4.1.9.9.834.1.1.7.1.18 | CiscoOpticalOtsOsri | read-write | current |
| cooOtsController2ProtectionPortRole OBJECT-TYPE This object represents the port role on optical channel interfaces. | 1.3.6.1.4.1.9.9.834.1.1.7.1.19 | CiscoOpticalOtsProtectionPortRole | read-only | current |
| cooOtsController2State OBJECT-TYPE This object represents the controller status of optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.7.1.20 | CiscoOpticalOtsAdminState | read-only | current |
| cooOtsController2TranspAdminState OBJECT-TYPE This object represents the transport administration status on optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.7.1.21 | CiscoOpticalOtsTranspAdminState | read-only | current |
| cooOtsController2AlarmState OBJECT-TYPE This object indicates the current alarms status of the Optics layer. Alarms description : noDefect : No alarms highRXPwr : Input optical power reading over the fail-high threshold highTXPwr : Output optical power reading over the fail-high threshold lowRXPwr : Input optical power reading below the fail-low threshold lowTXPwr : Output optical power reading below the fail-low threshold lospRXPwr : Loss of optical power signal locRXPwr : Loss of optical continuity degLowGain : Amplifier gain degrade low degHighGain : Amplifier gain degrade high alsAmp : Amplifier automatic laser shutdown for safety reason aprAmp : Amplifier automatic power reduction noEqAutoAmp : Channels power not equalized for amplifier automatic control mode misAutoAmp : Misconfiguration for amplifier automatic control mode switchToProtect : Protected port switching to active role autoAmpliCtrlRunning : Amplifier automatic control mode algorithm running | 1.3.6.1.4.1.9.9.834.1.1.7.1.22 | Bits {noDefect(0), highRXPwr(1), highTXPwr(2), lowRXPwr(3), lowTXPwr(4), lospRXPwr(5), locRXPwr(6), degLowGain(7), degHighGain(8), alsAmp(9), aprAmp(10), noEqAutoAmp(11), misAutoAmp(12), switchToProtect(13), autoAmpliCtrlRunning(14)} | read-only | current |
| cooOtsController2RXSpanLoss OBJECT-TYPE This object is used to represents the span loss power in 1/100 dB on optical OTS interfaces | 1.3.6.1.4.1.9.9.834.1.1.7.1.23 | CoiOpticalPower (-4000..3000) | read-only | current |
| cooOtsController2TXSpanLoss OBJECT-TYPE This object is used to represents the span loss power in 1/100 dB on optical OTS interfaces | 1.3.6.1.4.1.9.9.834.1.1.7.1.24 | CoiOpticalPower (-4000..3000) | read-only | current |
| cooOtsController2RXEnabled OBJECT-TYPE This object represents the RX direction status of optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.7.1.25 | TruthValue | read-write | current |
| cooOtsController2TXEnabled OBJECT-TYPE This object represents the TX direction status of optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.7.1.26 | TruthValue | read-write | current |
| cooOtsController2IAmpliGain OBJECT-TYPE This object represents the amplifier gain value in 1/10 dB on optical OTS interfaces for ingress direction. | 1.3.6.1.4.1.9.9.834.1.1.7.1.27 | CiscoOpticalOts2IEGainInDb | read-only | current |
| cooOtsController2IAmpliTilt OBJECT-TYPE This object represents the amplifier tilt value in 1/10 dB on optical OTS interfaces for ingress direction. | 1.3.6.1.4.1.9.9.834.1.1.7.1.28 | CiscoOpticalOtsIETiltInDb | read-only | current |
| cooOtsController2IAmpliGainRange OBJECT-TYPE This object represents the Ingress amplifier gain range. | 1.3.6.1.4.1.9.9.834.1.1.7.1.29 | CiscoOpticalOtsAmpliGainRange | read-only | current |
| cooOtsController2ISafetyControlMode OBJECT-TYPE This object represents the Ingress safety control mode. | 1.3.6.1.4.1.9.9.834.1.1.7.1.30 | CiscoOpticalOtsAmpliSafetyCtrlMode | read-only | current |
| cooOtsController2IAmpliOsri OBJECT-TYPE This object represents the Ingress OSRI. | 1.3.6.1.4.1.9.9.834.1.1.7.1.31 | CiscoOpticalOtsOsri | read-only | current |
| cooOtsController2EAmpliGain OBJECT-TYPE This object represents the amplifier gain value in 1/10 dB on optical OTS interfaces for Egress direction. | 1.3.6.1.4.1.9.9.834.1.1.7.1.32 | CiscoOpticalOts2IEGainInDb | read-write | current |
| cooOtsController2EAmpliTilt OBJECT-TYPE This object represents the amplifier tilt value in 1/10 dB on optical OTS interfaces for egress direction. | 1.3.6.1.4.1.9.9.834.1.1.7.1.33 | CiscoOpticalOtsIETiltInDb | read-only | current |
| cooOtsController2EAmpliGainRange OBJECT-TYPE This object represents the Egress amplifier gain range. | 1.3.6.1.4.1.9.9.834.1.1.7.1.34 | CiscoOpticalOtsAmpliGainRange | read-only | current |
| cooOtsController2ESafetyControlMode OBJECT-TYPE This object is used to configure Egress safety control mode. | 1.3.6.1.4.1.9.9.834.1.1.7.1.35 | CiscoOpticalOtsAmpliSafetyCtrlMode | read-write | current |
| cooOtsController2EAmpliOsri OBJECT-TYPE This object is used to configure Egress OSRI. | 1.3.6.1.4.1.9.9.834.1.1.7.1.36 | CiscoOpticalOtsOsri | read-write | current |
| cooOtsController2TotLCTXPower OBJECT-TYPE This object represents the transmit power(C+L) in 1/100 dBm on optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.7.1.37 | CoiOpticalPower | read-only | current |
| cooOtsController2TotLCRXPower OBJECT-TYPE This object represents the receive power(C+L) in 1/100 dBm on optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.7.1.38 | CoiOpticalPower | read-only | current |
| cooOtsController2IForceApr OBJECT-TYPE This object represents Force Automatic Power Reduction for OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.7.1.39 | INTEGER {off(0), on(1)} | read-only | current |
| cooOtsController2EForceApr OBJECT-TYPE This object represents Force Automatic Power Reduction for OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.7.1.40 | INTEGER {off(0), on(1)} | read-only | current |
| cooOtsController2BrPower OBJECT-TYPE This object represents the BR power in 1/100 dBm on optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.7.1.41 | CoiOpticalPower | read-only | current |
| cooOtsController2LedState OBJECT-TYPE This object represents LED state for OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.7.1.42 | INTEGER {off(0), greenOn(1), greenFlashing(2), yellowOn(3), yellowFlashing(4), redOn(5), redFlashing(6), na(7)} | read-only | current |
| cooOtsController2EAmpliBrRatio OBJECT-TYPE This object represents EgressAmpliBrRatio for OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.7.1.43 | CiscoOpticalOtsBrRatioInDb | read-only | current |
| cooOtsController2AmpliControlModeConfigVal OBJECT-TYPE This object represents the Configured Amplifier Control Mode Value for OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.7.1.44 | CiscoOpticalOtsAmpliControlMode | read-write | current |
| cooOtsController2EAmpliPowerConfigVal OBJECT-TYPE This object represents the Configured Egress Amplifier Power Value in 1/100 dBm on optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.7.1.45 | CoiOpticalPower | read-write | current |
| cooOtsController2Temperature OBJECT-TYPE This object represents the Controller Temperature in 1/100 C on optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.7.1.46 | CiscoOpticalOtsTemperature | read-only | current |
| cooOtsController2Voltage OBJECT-TYPE This object represents the Controller Voltage in 1/100 V on optical OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.7.1.47 | CiscoOpticalOtsVoltage | read-only | current |
| cooOtsController2EAmpliBrPower OBJECT-TYPE This object represents EgressAmpliBrPower for OTS interfaces. | 1.3.6.1.4.1.9.9.834.1.1.7.1.48 | CoiOpticalPower | read-only | current |
| cooOtsPerformanceMonitoring OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.834.1.2 | |||
| cooOtsThresholdTable OBJECT-TYPE This table provides threshold information for optical layer related attributes of interfaces with an ifType of opticalTransport(196) and interval type as cooThreshIntervalType. | 1.3.6.1.4.1.9.9.834.1.2.1 | not-accessible | current | |
| cooOtsThresholdEntry OBJECT-TYPE An entry containing threshold information on optical layer related attributes of interfaces with an ifType opticalTransport(196). Entries are created by the feature when a new interface is added to the ifTable. | 1.3.6.1.4.1.9.9.834.1.2.1.1 | not-accessible | current | |
| cooThreshIntervalType OBJECT-TYPE This object represents the interval type during which the performance statistics are accumulated for the interface. | 1.3.6.1.4.1.9.9.834.1.2.1.1.1 | CoiIntervalType | not-accessible | current |
| cooThreshTXPowerMin OBJECT-TYPE This object is used to configure the threshold of minimum transmit power for the interface in 1/100 dBm. | 1.3.6.1.4.1.9.9.834.1.2.1.1.2 | CoiOpticalPower | read-write | current |
| cooThreshRXPowerMin OBJECT-TYPE This object is used to configure the threshold of minimum receive power for the interface in 1/100 dBm. | 1.3.6.1.4.1.9.9.834.1.2.1.1.3 | CoiOpticalPower | read-write | current |
| cooThreshLBCMin OBJECT-TYPE This object is used to configure the threshold of minimum laser bias current in 1/10 percent. | 1.3.6.1.4.1.9.9.834.1.2.1.1.4 | Unsigned32 (0..100) | read-only | current |
| cooThreshTXPowerMax OBJECT-TYPE This object is used to configure the threshold of maximum Transmit power for the interface in 1/100 dBm. | 1.3.6.1.4.1.9.9.834.1.2.1.1.5 | CoiOpticalPower | read-write | current |
| cooThreshRXPowerMax OBJECT-TYPE This object is used to configure the threshold of maximum receive power for the interface in 1/100 dBm. | 1.3.6.1.4.1.9.9.834.1.2.1.1.6 | CoiOpticalPower | read-write | current |
| cooThreshLBCMax OBJECT-TYPE This object is used to configure the threshold of maximum Laser Bias Current in 1/10 percent for the interface. | 1.3.6.1.4.1.9.9.834.1.2.1.1.7 | Unsigned32 (0..100) | read-only | current |
| cooThreshTXPowerEnableMin OBJECT-TYPE This object is used to configure the enablement of threshold minimum transmit power for the interface. | 1.3.6.1.4.1.9.9.834.1.2.1.1.8 | TruthValue | read-write | current |
| cooThreshRXPowerEnableMin OBJECT-TYPE This object is used to configure the enablement of the threshold minimum receive power for the interface. | 1.3.6.1.4.1.9.9.834.1.2.1.1.9 | TruthValue | read-write | current |
| cooThreshLBCEnableMin OBJECT-TYPE This object is used to configure the enablement of the threshold minimum laser bias current for the interface. | 1.3.6.1.4.1.9.9.834.1.2.1.1.10 | TruthValue | read-write | current |
| cooThreshTXPowerEnableMax OBJECT-TYPE This object is used to configure the enablement of the threshold maximum transmit power for the interface. | 1.3.6.1.4.1.9.9.834.1.2.1.1.11 | TruthValue | read-write | current |
| cooThreshRXPowerEnableMax OBJECT-TYPE This object is used to configure the enablement of the threshold maximum receive power for the interface. | 1.3.6.1.4.1.9.9.834.1.2.1.1.12 | TruthValue | read-write | current |
| cooThreshLBCEnableMax OBJECT-TYPE This object is used to configure the enablement of the threshold maximum laser bias current for the interface. | 1.3.6.1.4.1.9.9.834.1.2.1.1.13 | TruthValue | read-write | current |
| cooThreshAmpliGainMin OBJECT-TYPE This object is used to configure the threshold of minimum ampli gain for the interface in 1/100 dB. | 1.3.6.1.4.1.9.9.834.1.2.1.1.14 | Integer32 (0..500) | read-write | current |
| cooThreshAmpliGainMax OBJECT-TYPE This object is used to configure the threshold of maximum ampli gain for the interface in 1/100 dB. | 1.3.6.1.4.1.9.9.834.1.2.1.1.15 | Integer32 (0..500) | read-write | current |
| cooThreshAmpliGainEnableMax OBJECT-TYPE This object is used to configure the enablement of the threshold maximum ampli gain for the interface. | 1.3.6.1.4.1.9.9.834.1.2.1.1.16 | TruthValue | read-write | current |
| cooThreshAmpliGainEnableMin OBJECT-TYPE This object is used to configure the enablement of the threshold minimum ampli gain for the interface. | 1.3.6.1.4.1.9.9.834.1.2.1.1.17 | TruthValue | read-write | current |
| cooThreshAmpliGainTiltMin OBJECT-TYPE This object is used to configure the threshold of minimum ampli gain tilt for the interface in 1/100 dB. | 1.3.6.1.4.1.9.9.834.1.2.1.1.18 | Integer32 (-50..50) | read-write | current |
| cooThreshAmpliGainTiltMax OBJECT-TYPE This object is used to configure the threshold of maximum ampli gain tilt for the interface in 1/100 dB. | 1.3.6.1.4.1.9.9.834.1.2.1.1.19 | Integer32 (-50..50) | read-write | current |
| cooThreshAmpliGainTiltEnableMax OBJECT-TYPE This object is used to configure the enablement of the threshold maximum ampli gain tilt for the interface. | 1.3.6.1.4.1.9.9.834.1.2.1.1.20 | TruthValue | read-write | current |
| cooThreshAmpliGainTiltEnableMin OBJECT-TYPE This object is used to configure the enablement of the threshold minimum ampli gain tilt for the interface. | 1.3.6.1.4.1.9.9.834.1.2.1.1.21 | TruthValue | read-write | current |
| cooOtsCurrentTable OBJECT-TYPE This table provides current information for optical layer related attributes of interfaces with an ifType of opticalChannel(196), lane as cooCurrentLane and interval as cooCurrentIntervalType. | 1.3.6.1.4.1.9.9.834.1.2.2 | not-accessible | current | |
| cooOtsCurrentEntry OBJECT-TYPE An entry containing current information on optical layer related attributes of interfaces with an ifType opticalChannel(196). Entries are created by the feature when a new interface is added to the ifTable. | 1.3.6.1.4.1.9.9.834.1.2.2.1 | not-accessible | current | |
| cooCurrentIntervalType OBJECT-TYPE This object represents the interval type during which the current performance statistics are accumulated. | 1.3.6.1.4.1.9.9.834.1.2.2.1.1 | CoiIntervalType | not-accessible | current |
| cooCurrentTXPowerMax OBJECT-TYPE This object specifies the current maximum transmit power for the interface in 1/100 dBm. | 1.3.6.1.4.1.9.9.834.1.2.2.1.2 | CoiOpticalPower | read-only | current |
| cooCurrentRXPowerMax OBJECT-TYPE This object specifies the current maximum receive power for the interface in 1/100 dBm. | 1.3.6.1.4.1.9.9.834.1.2.2.1.3 | CoiOpticalPower | read-only | current |
| cooCurrentLBCMax OBJECT-TYPE This object specifies the current maximum laser bias current in 1/10 percent for the interface. | 1.3.6.1.4.1.9.9.834.1.2.2.1.4 | Unsigned32 (0..100) | read-only | current |
| cooCurrentTXPowerMin OBJECT-TYPE This object specifies the current minimum transmit power for the interface in 1/100 dBm. | 1.3.6.1.4.1.9.9.834.1.2.2.1.5 | CoiOpticalPower | read-only | current |
| cooCurrentRXPowerMin OBJECT-TYPE This object specifies the current minimum receive power for the interface in 1/100 dBm. | 1.3.6.1.4.1.9.9.834.1.2.2.1.6 | CoiOpticalPower | read-only | current |
| cooCurrentLBCMin OBJECT-TYPE This object specifies the current minimum laser bias current in 1/10 percent for the interface. | 1.3.6.1.4.1.9.9.834.1.2.2.1.7 | Unsigned32 (0..100) | read-only | current |
| cooCurrentTXPowerAvg OBJECT-TYPE This object specifies the current average transmit power for the interface in 1/100 dBm. | 1.3.6.1.4.1.9.9.834.1.2.2.1.8 | CoiOpticalPower | read-only | current |
| cooCurrentRXPowerAvg OBJECT-TYPE This object specifies the current average receive power for the interface in 1/100 dBm. | 1.3.6.1.4.1.9.9.834.1.2.2.1.9 | CoiOpticalPower | read-only | current |
| cooCurrentLBCAvg OBJECT-TYPE This object specifies the current average Laser Bias Current in 1/10 percent for the interface. | 1.3.6.1.4.1.9.9.834.1.2.2.1.10 | Unsigned32 (0..100) | read-only | current |
| cooCurrentTimestamp OBJECT-TYPE This object specifies the timestamp for the current bucket for the interface. | 1.3.6.1.4.1.9.9.834.1.2.2.1.11 | OCTET STRING | read-only | current |
| cooCurrentAmpliGainMin OBJECT-TYPE This object specifies the current minimum amplifier gain for the interface in 1/100 dB. | 1.3.6.1.4.1.9.9.834.1.2.2.1.12 | Integer32 | read-only | current |
| cooCurrentAmpliGainMax OBJECT-TYPE This object specifies the current maximum amplifier gain for the interface in 1/100 dB. | 1.3.6.1.4.1.9.9.834.1.2.2.1.13 | Integer32 | read-only | current |
| cooCurrentAmpliGainAvg OBJECT-TYPE This object specifies the current average amplifier gain for the interface in 1/100 dB. | 1.3.6.1.4.1.9.9.834.1.2.2.1.14 | Integer32 | read-only | current |
| cooCurrentAmpliGainTiltMin OBJECT-TYPE This object specifies the current minimum amplifier gain tilt for the interface in 1/100 dB. | 1.3.6.1.4.1.9.9.834.1.2.2.1.15 | Integer32 | read-only | current |
| cooCurrentAmpliGainTiltMax OBJECT-TYPE This object specifies the current maximum amplifier gain tilt for the interface in 1/100 dB. | 1.3.6.1.4.1.9.9.834.1.2.2.1.16 | Integer32 | read-only | current |
| cooCurrentAmpliGainTiltAvg OBJECT-TYPE This object specifies the current average amplifier gain tilt for the interface in 1/100 dB. | 1.3.6.1.4.1.9.9.834.1.2.2.1.17 | Integer32 | read-only | current |
| cooCurrentTXPowerCLMin OBJECT-TYPE This object specifies the current minimum transmit power C+L for the interface in 1/100 dBm. | 1.3.6.1.4.1.9.9.834.1.2.2.1.18 | CoiOpticalPower | read-only | current |
| cooCurrentTXPowerCLMax OBJECT-TYPE This object specifies the current maximum transmit power C+L for the interface in 1/100 dBm. | 1.3.6.1.4.1.9.9.834.1.2.2.1.19 | CoiOpticalPower | read-only | current |
| cooCurrentTXPowerCLAvg OBJECT-TYPE This object specifies the current Average transmit power C+L for the interface in 1/100 dBm. | 1.3.6.1.4.1.9.9.834.1.2.2.1.20 | CoiOpticalPower | read-only | current |
| cooCurrentRXPowerCLMin OBJECT-TYPE This object specifies the current minimum receive power for the interface in 1/100 dBm. | 1.3.6.1.4.1.9.9.834.1.2.2.1.21 | CoiOpticalPower | read-only | current |
| cooCurrentRXPowerCLMax OBJECT-TYPE This object specifies the current maximun receive power for the interface in 1/100 dBm. | 1.3.6.1.4.1.9.9.834.1.2.2.1.22 | CoiOpticalPower | read-only | current |
| cooCurrentRXPowerCLAvg OBJECT-TYPE This object specifies the current average receive power for the interface in 1/100 dBm. | 1.3.6.1.4.1.9.9.834.1.2.2.1.23 | CoiOpticalPower | read-only | current |
| cooCurrentIAmpliGainMin OBJECT-TYPE This object specifies the current minimum ingress amplifier gain for the interface in 1/100 dB. | 1.3.6.1.4.1.9.9.834.1.2.2.1.24 | Integer32 | read-only | current |
| cooCurrentIAmpliGainMax OBJECT-TYPE This object specifies the current maximum ingress amplifier gain for the interface in 1/100 dB. | 1.3.6.1.4.1.9.9.834.1.2.2.1.25 | Integer32 | read-only | current |
| cooCurrentIAmpliGainAvg OBJECT-TYPE This object specifies the current average ingress amplifier gain for the interface in 1/100 dB. | 1.3.6.1.4.1.9.9.834.1.2.2.1.26 | Integer32 | read-only | current |
| cooCurrentEAmpliGainMin OBJECT-TYPE This object specifies the current minimum egress amplifier gain for the interface in 1/100 dB. | 1.3.6.1.4.1.9.9.834.1.2.2.1.27 | Integer32 | read-only | current |
| cooCurrentEAmpliGainMax OBJECT-TYPE This object specifies the current maximum egress amplifier gain for the interface in 1/100 dB. | 1.3.6.1.4.1.9.9.834.1.2.2.1.28 | Integer32 | read-only | current |
| cooCurrentEAmpliGainAvg OBJECT-TYPE This object specifies the current average egress amplifier gain for the interface in 1/100 dB. | 1.3.6.1.4.1.9.9.834.1.2.2.1.29 | Integer32 | read-only | current |
| cooCurrentIAmpliGainTiltMin OBJECT-TYPE This object specifies the current minimum ingress amplifier gain tilt for the interface in 1/100 dB. | 1.3.6.1.4.1.9.9.834.1.2.2.1.30 | Integer32 | read-only | current |
| cooCurrentIAmpliGainTiltMax OBJECT-TYPE This object specifies the current maximum ingress amplifier gain tilt for the interface in 1/100 dB. | 1.3.6.1.4.1.9.9.834.1.2.2.1.31 | Integer32 | read-only | current |
| cooCurrentIAmpliGainTiltAvg OBJECT-TYPE This object specifies the current average ingress amplifier gain tilt for the interface in 1/100 dB. | 1.3.6.1.4.1.9.9.834.1.2.2.1.32 | Integer32 | read-only | current |
| cooCurrentEAmpliGainTiltMin OBJECT-TYPE This object specifies the current minimum egress amplifier gain tilt for the interface in 1/100 dB. | 1.3.6.1.4.1.9.9.834.1.2.2.1.33 | Integer32 | read-only | current |
| cooCurrentEAmpliGainTiltMax OBJECT-TYPE This object specifies the current maximum egress amplifier gain tilt for the interface in 1/100 dB. | 1.3.6.1.4.1.9.9.834.1.2.2.1.34 | Integer32 | read-only | current |
| cooCurrentEAmpliGainTiltAvg OBJECT-TYPE This object specifies the current average egress amplifier gain tilt for the interface in 1/100 dB. | 1.3.6.1.4.1.9.9.834.1.2.2.1.35 | Integer32 | read-only | current |
| cooOtsIntervalTable OBJECT-TYPE This table provides interval information for optical layer related attributes of interfaces with an ifType of opticalChannel(196), lane as cooIntervalLane, Interval as cooIntervalIntervalType and history bucket as cooIntervalIntervalType. | 1.3.6.1.4.1.9.9.834.1.2.3 | not-accessible | current | |
| cooOtsIntervalEntry OBJECT-TYPE An entry containing interval information on optical layer related attributes of interfaces with an ifType opticalChannel(196). Entries are created by the feature when a new interface is added to the ifTable. | 1.3.6.1.4.1.9.9.834.1.2.3.1 | not-accessible | current | |
| cooIntervalType OBJECT-TYPE This object represents the interval type during which the performance statistics are accumulated. | 1.3.6.1.4.1.9.9.834.1.2.3.1.1 | CoiIntervalType | not-accessible | current |
| cooIntervalNum OBJECT-TYPE This object identifies the interval for which the set of interval performance values is available. The interval identified by 1 is the most recent 15 minute or 24 hour interval, and the interval identified by N is the interval immediately preceding the one identified by N-1. | 1.3.6.1.4.1.9.9.834.1.2.3.1.2 | Unsigned32 (1..31) | not-accessible | current |
| cooIntervalTXPowerMax OBJECT-TYPE This object specifies the interval maximum transmit power in 1/100 dBm for the interface. | 1.3.6.1.4.1.9.9.834.1.2.3.1.3 | CoiOpticalPower | read-only | current |
| cooIntervalRXPowerMax OBJECT-TYPE This object specifies the interval maximum receive power in 1/100 dBm for the interface. | 1.3.6.1.4.1.9.9.834.1.2.3.1.4 | CoiOpticalPower | read-only | current |
| cooIntervalLBCMax OBJECT-TYPE This object specifies the interval maximum laser bias current in 1/10 percent for the interface. | 1.3.6.1.4.1.9.9.834.1.2.3.1.5 | Unsigned32 (0..100) | read-only | current |
| cooIntervalTXPowerMin OBJECT-TYPE This object specifies the interval minimum transmit power in 1/100 dBm for the interface. | 1.3.6.1.4.1.9.9.834.1.2.3.1.6 | CoiOpticalPower | read-only | current |
| cooIntervalRXPowerMin OBJECT-TYPE This object specifies the interval minimum receive power in 1/100 dBm for the interface. | 1.3.6.1.4.1.9.9.834.1.2.3.1.7 | CoiOpticalPower | read-only | current |
| cooIntervalLBCMin OBJECT-TYPE This object specifies the interval minimum laser bias current in 1/10 percent for the interface. | 1.3.6.1.4.1.9.9.834.1.2.3.1.8 | Unsigned32 (0..100) | read-only | current |
| cooIntervalTXPowerAvg OBJECT-TYPE This object specifies the interval average transmit power in 1/100 dBm for the interface. | 1.3.6.1.4.1.9.9.834.1.2.3.1.9 | CoiOpticalPower | read-only | current |
| cooIntervalRXPowerAvg OBJECT-TYPE This object specifies the interval average receive power in 1/100 dBm for the interface. | 1.3.6.1.4.1.9.9.834.1.2.3.1.10 | CoiOpticalPower | read-only | current |
| cooIntervalLBCAvg OBJECT-TYPE This object specifies the interval average laser bias current in 1/10 percent for the interface. | 1.3.6.1.4.1.9.9.834.1.2.3.1.11 | Unsigned32 (0..100) | read-only | current |
| cooIntervalTimestamp OBJECT-TYPE This object specifies the timestamp, for the bucket specified by 'cooIntervalNum', for the interface. | 1.3.6.1.4.1.9.9.834.1.2.3.1.12 | OCTET STRING | read-only | current |
| cooIntervalAmpliGainMin OBJECT-TYPE This object specifies the interval minimum amplifier gain in 1/100 dB for the interface. | 1.3.6.1.4.1.9.9.834.1.2.3.1.13 | Integer32 | read-only | current |
| cooIntervalAmpliGainMax OBJECT-TYPE This object specifies the interval maximum amplifier gain in 1/100 dB for the interface. | 1.3.6.1.4.1.9.9.834.1.2.3.1.14 | Integer32 | read-only | current |
| cooIntervalAmpliGainAvg OBJECT-TYPE This object specifies the interval acerage amplifier gain in 1/100 dB for the interface. | 1.3.6.1.4.1.9.9.834.1.2.3.1.15 | Integer32 | read-only | current |
| cooIntervalAmpliGainTiltMin OBJECT-TYPE This object specifies the interval minimum amplifier gain tilt in 1/100 dB for the interface. | 1.3.6.1.4.1.9.9.834.1.2.3.1.16 | Integer32 | read-only | current |
| cooIntervalAmpliGainTiltMax OBJECT-TYPE This object specifies the interval maximum amplifier gain tilt in 1/100 dB for the interface. | 1.3.6.1.4.1.9.9.834.1.2.3.1.17 | Integer32 | read-only | current |
| cooIntervalAmpliGainTiltAvg OBJECT-TYPE This object specifies the interval average amplifier gain tilt in 1/100 dB for the interface. | 1.3.6.1.4.1.9.9.834.1.2.3.1.18 | Integer32 | read-only | current |
| cooIntervalTXPowerCLMin OBJECT-TYPE This object specifies the interval minimum transmit power C+L for the interface in 1/100 dBm. | 1.3.6.1.4.1.9.9.834.1.2.3.1.19 | CoiOpticalPower | read-only | current |
| cooIntervalTXPowerCLMax OBJECT-TYPE This object specifies the interval maximum transmit power C+L for the interface in 1/100 dBm. | 1.3.6.1.4.1.9.9.834.1.2.3.1.20 | CoiOpticalPower | read-only | current |
| cooIntervalTXPowerCLAvg OBJECT-TYPE This object specifies the interval Average transmit power C+L for the interface in 1/100 dBm. | 1.3.6.1.4.1.9.9.834.1.2.3.1.21 | CoiOpticalPower | read-only | current |
| cooIntervalRXPowerCLMin OBJECT-TYPE This object specifies the interval minimum receive power for the interface in 1/100 dBm. | 1.3.6.1.4.1.9.9.834.1.2.3.1.22 | CoiOpticalPower | read-only | current |
| cooIntervalRXPowerCLMax OBJECT-TYPE This object specifies the interval maximun receive power for the interface in 1/100 dBm. | 1.3.6.1.4.1.9.9.834.1.2.3.1.23 | CoiOpticalPower | read-only | current |
| cooIntervalRXPowerCLAvg OBJECT-TYPE This object specifies the interval average receive power for the interface in 1/100 dBm. | 1.3.6.1.4.1.9.9.834.1.2.3.1.24 | CoiOpticalPower | read-only | current |
| cooIntervalIAmpliGainMin OBJECT-TYPE This object specifies the interval minimum ingress amplifier gain for the interface in 1/100 dB. | 1.3.6.1.4.1.9.9.834.1.2.3.1.25 | Integer32 | read-only | current |
| cooIntervalIAmpliGainMax OBJECT-TYPE This object specifies the interval maximum ingress amplifier gain for the interface in 1/100 dB. | 1.3.6.1.4.1.9.9.834.1.2.3.1.26 | Integer32 | read-only | current |
| cooIntervalIAmpliGainAvg OBJECT-TYPE This object specifies the interval average ingress amplifier gain for the interface in 1/100 dB. | 1.3.6.1.4.1.9.9.834.1.2.3.1.27 | Integer32 | read-only | current |
| cooIntervalEAmpliGainMin OBJECT-TYPE This object specifies the interval minimum egress amplifier gain for the interface in 1/100 dB. | 1.3.6.1.4.1.9.9.834.1.2.3.1.28 | Integer32 | read-only | current |
| cooIntervalEAmpliGainMax OBJECT-TYPE This object specifies the interval maximum egress amplifier gain for the interface in 1/100 dB. | 1.3.6.1.4.1.9.9.834.1.2.3.1.29 | Integer32 | read-only | current |
| cooIntervalEAmpliGainAvg OBJECT-TYPE This object specifies the interval average egress amplifier gain for the interface in 1/100 dB. | 1.3.6.1.4.1.9.9.834.1.2.3.1.30 | Integer32 | read-only | current |
| cooIntervalIAmpliGainTiltMin OBJECT-TYPE This object specifies the interval minimum ingress amplifier gain tilt for the interface in 1/100 dB. | 1.3.6.1.4.1.9.9.834.1.2.3.1.31 | Integer32 | read-only | current |
| cooIntervalIAmpliGainTiltMax OBJECT-TYPE This object specifies the interval maximum ingress amplifier gain tilt for the interface in 1/100 dB. | 1.3.6.1.4.1.9.9.834.1.2.3.1.32 | Integer32 | read-only | current |
| cooIntervalIAmpliGainTiltAvg OBJECT-TYPE This object specifies the interval average ingress amplifier gain tilt for the interface in 1/100 dB. | 1.3.6.1.4.1.9.9.834.1.2.3.1.33 | Integer32 | read-only | current |
| cooIntervalEAmpliGainTiltMin OBJECT-TYPE This object specifies the interval minimum egress amplifier gain tilt for the interface in 1/100 dB. | 1.3.6.1.4.1.9.9.834.1.2.3.1.34 | Integer32 | read-only | current |
| cooIntervalEAmpliGainTiltMax OBJECT-TYPE This object specifies the interval maximum egress amplifier gain tilt for the interface in 1/100 dB. | 1.3.6.1.4.1.9.9.834.1.2.3.1.35 | Integer32 | read-only | current |
| cooIntervalEAmpliGainTiltAvg OBJECT-TYPE This object specifies the interval average egress amplifier gain tilt for the interface in 1/100 dB. | 1.3.6.1.4.1.9.9.834.1.2.3.1.36 | Integer32 | read-only | current |
| cooOtsEquipmentAlarmGroup OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.834.1.5 | |||
| cooOtsAlarmLocation OBJECT-TYPE This object indicates the location of the component that raised alarm, within the device. | 1.3.6.1.4.1.9.9.834.1.5.1 | SnmpAdminString | accessible-for-notify | current |
| cooOtsAlarmType OBJECT-TYPE This object indicates the type of alarm that is raised. | 1.3.6.1.4.1.9.9.834.1.5.2 | CoiOptAlarmType | accessible-for-notify | current |
| cooOtsAlarmTimeStamp OBJECT-TYPE This object represents the time when an event occurred. This is accurate only upto a second. | 1.3.6.1.4.1.9.9.834.1.5.3 | TimeStamp | accessible-for-notify | current |
| cooOtsAlarmName OBJECT-TYPE This object represents the user-visible name, which uniquely identifies the alarm in the system. | 1.3.6.1.4.1.9.9.834.1.5.4 | SnmpAdminString | accessible-for-notify | current |
| cooOtsAlarmAdditionalInfo OBJECT-TYPE This object provides additional information about the alarm. This object would be an empty string if no additional information is specified. | 1.3.6.1.4.1.9.9.834.1.5.5 | SnmpAdminString | accessible-for-notify | current |
| cooOtsAlarmSeverity OBJECT-TYPE This object specifies alarm severity. | 1.3.6.1.4.1.9.9.834.1.5.6 | CoiOptAlarmSeverity | accessible-for-notify | current |
| cooOtsAlarmStatus OBJECT-TYPE This object specifies alarm status. | 1.3.6.1.4.1.9.9.834.1.5.7 | CoiOptAlarmStatus | accessible-for-notify | current |
| cooOtsAlarmServiceAffecting OBJECT-TYPE This object specifies the service affecting state of the alarm. | 1.3.6.1.4.1.9.9.834.1.5.8 | CoiOptAlarmServiceAffecting | accessible-for-notify | current |
| ciscoOpticalOtsMIBConformance OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.834.2 | |||
| ciscoOpticalOtsMIBCompliances OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.834.2.1 | |||
| ciscoOpticalOtsMIBGroups OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.834.2.2 |
Notifications
| Name | OID | Status |
|---|---|---|
| cooOtsStatusChange NOTIFICATION-TYPE This notification is generated when the value of cooOtsControllerStatus changes. The varbind for this notification indicates the ifIndex, ifname of the OTS interface as well as controller port type and status. | 1.3.6.1.4.1.9.9.834.0.1 | current |
| cooOtsOchStatusChange NOTIFICATION-TYPE This notification is generated when the value of cooOtsOchControllerStatus changes. The varbind for this notification indicates the ifIndex, ifname of the OTS-OCH interface as well as controller port type and status. | 1.3.6.1.4.1.9.9.834.0.2 | current |
| cooOtsEquipmentAlarm NOTIFICATION-TYPE This notification is generated whenever the optical equipment alarm is generated. | 1.3.6.1.4.1.9.9.834.0.3 | current |
Conformance
| Name | OID | Status |
|---|---|---|
| ciscoOpticalOtsMIBCompliance MODULE-COMPLIANCE The compliance statement for platforms that monitor the parameters for the optical interfaces. | 1.3.6.1.4.1.9.9.834.2.1.1 | current |
| cooOtsGroup OBJECT-GROUP The collection of objects to provide information related to the optical OTS characteristics for interfaces of ifType opticalChannel(196). | 1.3.6.1.4.1.9.9.834.2.2.1 | current |
| cooOtsOchGroup OBJECT-GROUP The collection of objects to give information related to the optical OTS-OCH characteristics for interfaces of ifType opticalChannel(196). | 1.3.6.1.4.1.9.9.834.2.2.2 | current |
| cooOtsControllerGroup OBJECT-GROUP The collection of objects to allow configurations and give information related to the optical OTS characteristics for interfaces of ifType opticalChannel(196). | 1.3.6.1.4.1.9.9.834.2.2.3 | current |
| cooOtsOchControllerGroup OBJECT-GROUP The collection of objects to allow configurations and give information related to the optical OTS-OCH characteristics for interfaces of ifType opticalChannel(196). | 1.3.6.1.4.1.9.9.834.2.2.4 | current |
| cooOtsThresholdGroup OBJECT-GROUP The collection of objects used for monitoring the threshold information for optical layer related attributes of interfaces with an ifType of opticalChannel(196). | 1.3.6.1.4.1.9.9.834.2.2.5 | current |
| cooOtsCurrentGroup OBJECT-GROUP The collection of objects used for monitoring the current information for optical layer related attributes of interfaces with an ifType of opticalChannel(196) in a current interval. | 1.3.6.1.4.1.9.9.834.2.2.6 | current |
| cooOtsIntervalGroup OBJECT-GROUP The collection of objects used for monitoring the interval information for optical layer related attributes of interfaces with an ifType of opticalChannel(196) in a given interval. | 1.3.6.1.4.1.9.9.834.2.2.7 | current |
| cooOtsNotifEnableGroup OBJECT-GROUP The collection of objects to enable the notification generations upon an interface's alarms status change on optics OTS layer. | 1.3.6.1.4.1.9.9.834.2.2.8 | current |
| cooOtsNotifGroup NOTIFICATION-GROUP The optical status change notifications whenever the alarms status of optical OTS layer on an interface changes. | 1.3.6.1.4.1.9.9.834.2.2.9 | current |
| cooOtsOchNotifGroup NOTIFICATION-GROUP The optical status change notifications whenever the alarms status of optical OTS-OCH layer on an interface changes. | 1.3.6.1.4.1.9.9.834.2.2.10 | current |
| cooOtsEquipmentAlarmInfoGroup OBJECT-GROUP The optical equipment notifications whenever the alarm is generated. | 1.3.6.1.4.1.9.9.834.2.2.11 | current |
| cooOtsPowerGroup OBJECT-GROUP The collection of objects used for monitoring the total power information for optical layer related attributes of interfaces with an ifType of opticalChannel(196). | 1.3.6.1.4.1.9.9.834.2.2.12 | current |
| cooOtsOchNotifEnableGroup OBJECT-GROUP The collection of objects to enable the notification generations upon an interface's alarms status change on optics OTS-OCH layer. | 1.3.6.1.4.1.9.9.834.2.2.13 | current |
| cooOtsController2Group OBJECT-GROUP The collection of objects to allow configurations and give information related to the optical OTS characteristics for interfaces of ifType opticalTransport(196) using the controller2 table. | 1.3.6.1.4.1.9.9.834.2.2.14 | current |