MIBs Depot

CISCO-OPTICAL-MIB

Registered at
1.3.6.1.4.1.9.9.828
Last updated
2016-05-24 00:00
Organization
Cisco Systems, Inc.
Revisions
2016-05-24 00:00, 2015-12-01 00:00, 2015-10-30 00:00
Namespace
cisco
Source file
CISCO-OPTICAL-MIB
Digest
sha256:0f66703444d02882ee127f8588f543abb936bac9ef1d3af776ca736218c2f2b8

Description

This MIB module defines the managed objects for physical layer characteristics of optical interfaces and performance statistics objects for protocol specific counters in optical devices. Performance monitoring (PM) parameters are used by service providers to gather, store, set thresholds for and report performance data for early detection of problems. Thresholds are used to set error levels for each PM parameter. During the accumulation cycle, if the current value of a performance monitoring parameter reaches or exceeds its corresponding threshold value, a threshold crossing alarm (TCA) is generated. The TCAs provide early detection of performance degradation. Glossary: LBC : Laser Bias Current TX : Transmit RX : Receive PMD : Polarization Mode Dispersion OSNR : Optical Signal to Noise Ratio DGD : Differential Group Delay CD : Chromatic Dispersion rad/s : radian per second dB : decibel dBm : decibel-milliwatt ps : picosecond nm : nanometer.

Contact

Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-<list>@cisco.com

Imports

FromSymbols
CISCO-SMIciscoMgmt
IF-MIBifIndex, ifName
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP
SNMPv2-SMIInteger32, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, Unsigned32, iso
SNMPv2-TCDisplayString, MacAddress, TEXTUAL-CONVENTION, TimeStamp, TruthValue

Imported by

1 module(s) in this corpus import this one.

Load order

Every file a consumer needs in order to load this module, dependencies first.

CISCO-OPTICAL-MIB
CISCO-SMI
IANAifType-MIB
IF-MIB
SNMPv2-CONF
SNMPv2-MIB
SNMPv2-SMI
SNMPv2-TC

Textual conventions

NameOIDSyntaxAccessStatus
CoiIntervalType
TEXTUAL-CONVENTION
This value indicates the time period over which performance monitoring data has been collected. Valid values are - fifteenMin(1) - values for the 15 min interval. oneDay(2) - values for the 1 Day interval. thirtySecond(3)- values for the 30 Sec interval.
current
CoiOptAlarmServiceAffecting
TEXTUAL-CONVENTION
This will indicate the sevice-affecting state of the alarm. Valid values are - Service affecting(1) - alarm affects service. Non-Service affecting(2)- alarm does not affect service.
current
CoiOptAlarmSeverity
TEXTUAL-CONVENTION
This will indicate the severity of the notification being sent out. Valid values are - notReported(1) - alarm not reported. notAlarmed(2) - alarm not raised. minor(3) - minor alarm. major(4) - major alarm. critical(5) - critical alarm.
current
CoiOptAlarmStatus
TEXTUAL-CONVENTION
This will indicate the status of the alarm. Valid values are - raised(1) - alarm in raised state. cleared(2) - alarm in cleared state. transient(3)- alarm in transient state.
current
CoiOptAlarmType
TEXTUAL-CONVENTION
This value indicates the alarm type. alarmUnknown(1) - denotes unknown alarm type. equipmentFailure(2) - denotes equipment fail alarm type.
current
CoiOpticalPower
TEXTUAL-CONVENTION
This value indicates the optical receive or transmit power.
current
CoiOpticalWavelength
TEXTUAL-CONVENTION
This value represents the wavelength of optical signals, in an optical interface. It is represented in units of nanometers. A value of zero either indicates that the wavelength is unknown, or that it does not fall under the frequency grid defined in ITU-T G.694.1
current
CoiPortType
TEXTUAL-CONVENTION
This value indicates the port type of the optical interface. Valid values are - clientPort(1) - denotes client port. trunkPort(2) - denotes trunk port.
current

Objects

NameOIDSyntaxAccessStatus
ciscoOpticalMIBNotifs
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.828.0
ciscoOpticalMIBObjects
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.828.1
coiOpticalController
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.828.1.1
coiOpticalNotifEnabled
OBJECT-TYPE
This object controls the generation of coiOpticsStatusChange notification. If the value of this object is 'true', then the generation of coiOpticsStatusChange notification is enabled. If the value of this object is 'false', then the generation of coiOpticsStatusChange notification is disabled.
1.3.6.1.4.1.9.9.828.1.1.1TruthValueread-writecurrent
coiOpticalControllerTable
OBJECT-TYPE
This table provides management information for optical layer related attributes of interfaces with an ifType of opticalChannel(195).
1.3.6.1.4.1.9.9.828.1.1.2not-accessiblecurrent
coiOpticalControllerEntry
OBJECT-TYPE
An entry containing management information on optical layer related attributes of interfaces with an ifType opticalChannel(195). Entries are created by the feature when a new interface is added to the ifTable.
1.3.6.1.4.1.9.9.828.1.1.2.1not-accessiblecurrent
coiOpticalControllerWavelength
OBJECT-TYPE
This object is used to configure the wavelength on optical channel interfaces in 1/100 nm.
1.3.6.1.4.1.9.9.828.1.1.2.1.1CoiOpticalWavelengthread-writecurrent
coiOpticalControllerLaserStatus
OBJECT-TYPE
This object gives the current operational state of the Laser. Valid values are - 'up' - The laser is operational. 'down' - The laser is not operational.
1.3.6.1.4.1.9.9.828.1.1.2.1.2INTEGER {up(1), down(2)}read-onlycurrent
coiOpticalControllerFrequency
OBJECT-TYPE
This object is used to configure the frequency on optical channel interfaces in 100 MHz.
1.3.6.1.4.1.9.9.828.1.1.2.1.3Unsigned32read-writecurrent
coiOpticalControllerChannelNumber
OBJECT-TYPE
This object is used to configure the channel number on optical channel interfaces. Channel Number is set to 0 if not 50GHz grid.
1.3.6.1.4.1.9.9.828.1.1.2.1.4Unsigned32read-writecurrent
coiOpticalControllerTransmitPower
OBJECT-TYPE
This object is used to configure the Transmit Power in 1/100 dBm on optical channel interfaces.
1.3.6.1.4.1.9.9.828.1.1.2.1.5CoiOpticalPowerread-writecurrent
coiOpticalControllerOpticsType
OBJECT-TYPE
This object gives the description of optics present on optical channel interfaces.
1.3.6.1.4.1.9.9.828.1.1.2.1.6DisplayStringread-onlycurrent
coiOpticalControllerRXLowThreshold
OBJECT-TYPE
This object is used to configure the Receive Low Threshold in 1/100 dBm on optical channel interfaces.
1.3.6.1.4.1.9.9.828.1.1.2.1.7CoiOpticalPowerread-writecurrent
coiOpticalControllerTXLowThreshold
OBJECT-TYPE
This object is used to configure the Transmit Low Threshold in 1/100 dBm on optical channel interfaces.
1.3.6.1.4.1.9.9.828.1.1.2.1.8CoiOpticalPowerread-writecurrent
coiOpticalControllerRXHighThreshold
OBJECT-TYPE
This object is used to configure the Receive High Threshold in 1/100 dBm on optical channel interfaces.
1.3.6.1.4.1.9.9.828.1.1.2.1.9CoiOpticalPowerread-writecurrent
coiOpticalControllerTXHighThreshold
OBJECT-TYPE
This object is used to configure the Transmit High Threshold in 1/100 dBm on optical channel interfaces.
1.3.6.1.4.1.9.9.828.1.1.2.1.10CoiOpticalPowerread-writecurrent
coiOpticalControllerLBCHighThreshold
OBJECT-TYPE
This object is used to configure the Laser Bias Current High Threshold in 1/10% on optical channel interfaces.
1.3.6.1.4.1.9.9.828.1.1.2.1.11Integer32 (0..1000)read-writecurrent
coiOpticalControllerStatus
OBJECT-TYPE
This object indicates the current defect status of the Optics layer. noDefect(0): No Defect. This bit is set high when no defect is detected on the optics. improprmvl(1): Improper Removal. This will be set when a physical pluggable is absent on a service (hw-module) provisioned port. mea(2): This bit will be set when Port Pluggable Module Mismatches With Pre-Provisoned PPM. provMismatch(3): Provision Mismatch. This bit is set when Provisioned wavelength is Not supported By Pluggable. highRXPwr(4): High Receive Power. This bit is set when the measured optical power of the received signal exceeds the threshold high value, which is user-provisionable. highTXPwr(5): High Transmit Power. This bit is set when Pluggable measured optical power of the transmitted signal falls over the threshold. lowRXPwr(6): Low Receive Power. This bit is set when the measured optical power of the received signal falls below the low threshold value, which is user-provisionable. lowTXPwr(7): Low Transmit Power. This bit is set when Pluggable measured optical power of the transmitted signal falls below the low threshold. highLBC(8): High Laser Bias. This bit is set when the Physical Pluggable Port laser reads laser bias value beyond configured high threshold. highDGD(9): High DGD. This bit is set when the pluggable port Module reads the Differential Group delay value that exceeds the configured high threshold. outOfRangeCD(10): Out of Range Chromatic Dispersion. This bit is set when the Chromatic dispersion value read by the associated HW is out of range with the configured threshold. lowOSNR(11): Low Optical Signal to Noise Ratio. This bit is set when the HW read Optical Signal to Noise ratio falls below the configured low threshold. wvlOutOfLock(12): Wavelength Out of Lock. This bit is set when Trunk Port optics detects that optical input frequency is out of range. highLaserTemp(13): High LaserTemp.This bit is set when the internally measured transceiver temperature exceeds the card setting by 35.6 degrees F or 2 degrees C. A laser temperature change affects the transmitted wavelength. lowLaserTemp(14): Low LaserTemp. This bit is set when the internally measured transceiver temperature falls below the card setting by 35.6 degrees F or 2 degrees C. A laser temperature change affects the transmitted wavelength. (This temperature is equivalent to about 200 picometers of wavelength. ppmFail(15): Pluggable Equipment Fail. This bit is set when Pluggable Equipment is not operational or manageable. This object is sent out as a notification to the agent.
1.3.6.1.4.1.9.9.828.1.1.2.1.12Bits {noDefect(0), improprmvl(1), mea(2), provMismatch(3), highRXPwr(4), highTXPwr(5), lowRXPwr(6), lowTXPwr(7), highLBC(8), highDGD(9), outOfRangeCD(10), lowOSNR(11), wvlOutOfLock(12), highLaserTemp(13), lowLaserTemp(14), ppmFail(15)}read-onlycurrent
coiOpticalControllerPortType
OBJECT-TYPE
This object gives the port type of the optical interface.
1.3.6.1.4.1.9.9.828.1.1.2.1.13CoiPortTyperead-onlycurrent
coiOpticalControllerTotalRXPower
OBJECT-TYPE
This object is used to configure the total receive power in 1/100 dBm on optical channel interfaces.
1.3.6.1.4.1.9.9.828.1.1.2.1.14CoiOpticalPowerread-writecurrent
coiOpticalControllerTotalTXPower
OBJECT-TYPE
This object is used to configure the total transmit power in 1/100 dBm on optical channel interfaces.
1.3.6.1.4.1.9.9.828.1.1.2.1.15CoiOpticalPowerread-writecurrent
coiOpticalControllerPerLaneTable
OBJECT-TYPE
This table provides the management information for optical layer related attributes of interfaces with an ifType of opticalChannel(195) and lane number as coiOpticalControllerLane.
1.3.6.1.4.1.9.9.828.1.1.3not-accessiblecurrent
coiOpticalControllerPerLaneEntry
OBJECT-TYPE
An entry containing management information on optical layer related attributes of interfaces with an ifType opticalChannel(195) and lane number as coiOpticalControllerLane. Entries are created by the feature when a new interface is added to the ifTable.
1.3.6.1.4.1.9.9.828.1.1.3.1not-accessiblecurrent
coiOpticalControllerLane
OBJECT-TYPE
This object specifies the lane number for the optical controller. Each optical controller is divided into data lanes, with each lane operating at some data rate, giving an aggregated bandwidth of the controller, as a whole. Lane is applicable for breakout mode of operation.
1.3.6.1.4.1.9.9.828.1.1.3.1.1Integer32 (1..12)not-accessiblecurrent
coiOpticalControllerPerLaneRXPower
OBJECT-TYPE
This object specifies the Receive power in 1/100 dBm.
1.3.6.1.4.1.9.9.828.1.1.3.1.2CoiOpticalPowerread-onlycurrent
coiOpticalControllerPerLaneTXPower
OBJECT-TYPE
This object specifies the Transmit power in 1/100 dBm.
1.3.6.1.4.1.9.9.828.1.1.3.1.3CoiOpticalPowerread-onlycurrent
coiOpticalControllerPerLaneLBC
OBJECT-TYPE
This object specifies the Laser Bias Current in 1/10%.
1.3.6.1.4.1.9.9.828.1.1.3.1.4Integer32 (0..1000)read-onlycurrent
coiOpticalControllerPerLaneOSNR
OBJECT-TYPE
This object specifies the Optical Signal to Noise Ratio in 1/100 dB.
1.3.6.1.4.1.9.9.828.1.1.3.1.5Integer32read-onlycurrent
coiOpticalControllerPerLaneChromaticDispersion
OBJECT-TYPE
This object specifies the measure of spread of light pulse in ps/nm.
1.3.6.1.4.1.9.9.828.1.1.3.1.6Integer32read-onlycurrent
coiOpticalControllerPerLaneDifferentialGroupDelay
OBJECT-TYPE
This object specifies the propagation time difference between eigenmodes X and Y in 1/100 ps.
1.3.6.1.4.1.9.9.828.1.1.3.1.7Integer32read-onlycurrent
coiOpticalControllerPerLaneSecondOrderPMD
OBJECT-TYPE
This object specifies the threshold Second Order Polarization Mode Dispersion in 1/100 ps^2.
1.3.6.1.4.1.9.9.828.1.1.3.1.8Integer32read-onlycurrent
coiOpticalControllerPerLanePolarizationDependentLoss
OBJECT-TYPE
This object specifies the threshold Polarization Dependent Loss in 1/100 dB.
1.3.6.1.4.1.9.9.828.1.1.3.1.9Integer32read-onlycurrent
coiOpticalControllerPerLanePolarizationChangeRate
OBJECT-TYPE
This object specifies the Polarization Change Rate in 1/100 rad/s.
1.3.6.1.4.1.9.9.828.1.1.3.1.10Integer32read-onlycurrent
coiOpticalControllerPerLanePhaseNoise
OBJECT-TYPE
This object specifies the Fluctuations in the Phase of a Waveform in 1/1000 dB.
1.3.6.1.4.1.9.9.828.1.1.3.1.11Integer32read-onlycurrent
coiOpticalPerformanceMonitoring
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.828.1.2
coiOpticalThresholdTable
OBJECT-TYPE
This table provides threshold information for optical layer related attributes of interfaces with an ifType of opticalChannel(195) and Interval type as coiOptThreshIntervalType.
1.3.6.1.4.1.9.9.828.1.2.1not-accessiblecurrent
coiOpticalThresholdEntry
OBJECT-TYPE
An entry containing threshold information on optical layer related attributes of interfaces with an ifType opticalChannel(195). Entries are created by the feature when a new interface is added to the ifTable.
1.3.6.1.4.1.9.9.828.1.2.1.1not-accessiblecurrent
coiOptThreshIntervalType
OBJECT-TYPE
This object gives the interval type during which the performance statistics are accumulated for the interface.
1.3.6.1.4.1.9.9.828.1.2.1.1.1CoiIntervalTypenot-accessiblecurrent
coiOptThreshTXPowerMin
OBJECT-TYPE
This object is used to configure the threshold of minimum Transmit power for the interface in 1/100 dBm.
1.3.6.1.4.1.9.9.828.1.2.1.1.2CoiOpticalPowerread-writecurrent
coiOptThreshRXPowerMin
OBJECT-TYPE
This object is used to configure the threshold of minimum Receive power for the interface in 1/100 dBm.
1.3.6.1.4.1.9.9.828.1.2.1.1.3CoiOpticalPowerread-writecurrent
coiOptThreshOSNRMin
OBJECT-TYPE
This object is used to configure the threshold of minimum Optical Signal to Noise Ratio for the interface in 1/100 dB.
1.3.6.1.4.1.9.9.828.1.2.1.1.4Integer32read-writecurrent
coiOptThreshChromaticDispersionMin
OBJECT-TYPE
This object is used to configure the threshold of minimum measure of spread of light pulse for the interface in ps/nm.
1.3.6.1.4.1.9.9.828.1.2.1.1.5Integer32read-writecurrent
coiOptThreshDifferentialGroupDelayMin
OBJECT-TYPE
This object is used to configure the threshold of minimum propagation time difference between eigenmodes X and Y for the interface in 1/100 ps.
1.3.6.1.4.1.9.9.828.1.2.1.1.6Integer32read-writecurrent
coiOptThreshSecondOrderPMDMin
OBJECT-TYPE
This object is used to configure the threshold of minimum Second Order Polarization Mode Dispersion for the interface in 1/100 ps^2.
1.3.6.1.4.1.9.9.828.1.2.1.1.7Integer32read-writecurrent
coiOptThreshPolarizationDependentLossMin
OBJECT-TYPE
This object is used to configure the threshold of minimum Polarization Dependent Loss for the interface in 1/100 dB.
1.3.6.1.4.1.9.9.828.1.2.1.1.8Integer32read-writecurrent
coiOptThreshPolarizationChangeRateMin
OBJECT-TYPE
This object is used to configure the threshold of minimum Polarization Change Rate for the interface in 1/100 rad/s.
1.3.6.1.4.1.9.9.828.1.2.1.1.9Integer32read-writecurrent
coiOptThreshPhaseNoiseMin
OBJECT-TYPE
This object is used to configure the threshold of minimum Fluctuations in the Phase of a Waveform for the interface in 1/1000 dB.
1.3.6.1.4.1.9.9.828.1.2.1.1.10Integer32read-writecurrent
coiOptThreshLBCMin
OBJECT-TYPE
This object is used to configure the threshold of minumum Laser Bias Current in 1/10%.
1.3.6.1.4.1.9.9.828.1.2.1.1.11Integer32 (0..1000)read-writecurrent
coiOptThreshTXPowerMax
OBJECT-TYPE
This object is used to configure the threshold of maximum Transmit power for the interface in 1/100 dBm.
1.3.6.1.4.1.9.9.828.1.2.1.1.12CoiOpticalPowerread-writecurrent
coiOptThreshRXPowerMax
OBJECT-TYPE
This object is used to configure the threshold of maximum Receive power for the interface in 1/100 dBm.
1.3.6.1.4.1.9.9.828.1.2.1.1.13CoiOpticalPowerread-writecurrent
coiOptThreshOSNRMax
OBJECT-TYPE
This object is used to configure the threshold of maximum Optical Signal to Noise Ratio for the interface in 1/100 dB.
1.3.6.1.4.1.9.9.828.1.2.1.1.14Integer32read-writecurrent
coiOptThreshChromaticDispersionMax
OBJECT-TYPE
This object is used to configure the threshold of maximum measure of spread of light pulse for the interface in ps/nm.
1.3.6.1.4.1.9.9.828.1.2.1.1.15Integer32read-writecurrent
coiOptThreshDifferentialGroupDelayMax
OBJECT-TYPE
This object is used to configure the threshold of maximum propagation time difference between eigenmodes X and Y for the interface in 1/100 ps.
1.3.6.1.4.1.9.9.828.1.2.1.1.16Integer32read-writecurrent
coiOptThreshSecondOrderPMDMax
OBJECT-TYPE
This object is used to configure the threshold of maximum Second Order Polarization Mode Dispersion for the interface in 1/100 ps^2.
1.3.6.1.4.1.9.9.828.1.2.1.1.17Integer32read-writecurrent
coiOptThreshPolarizationDependentLossMax
OBJECT-TYPE
This object is used to configure the threshold of maximum Polarization Dependent Loss for the interface in 1/100 dB.
1.3.6.1.4.1.9.9.828.1.2.1.1.18Integer32read-writecurrent
coiOptThreshPolarizationChangeRateMax
OBJECT-TYPE
This object is used to configure the threshold of maximum Polarization Change Rate in 1/100 rad/s for the interface.
1.3.6.1.4.1.9.9.828.1.2.1.1.19Integer32read-writecurrent
coiOptThreshPhaseNoiseMax
OBJECT-TYPE
This object is used to configure the threshold of maximum Fluctuations in the Phase of a Waveform in 1/1000 dB for the interface.
1.3.6.1.4.1.9.9.828.1.2.1.1.20Integer32read-writecurrent
coiOptThreshLBCMax
OBJECT-TYPE
This object is used to configure the threshold of maximum Laser Bias Current in 1/10 % for the interface.
1.3.6.1.4.1.9.9.828.1.2.1.1.21Integer32 (0..1000)read-writecurrent
coiOptThreshTXPowerEnableMin
OBJECT-TYPE
This object is used to configure the enablement of threshold min Transmit power for the interface.
1.3.6.1.4.1.9.9.828.1.2.1.1.22TruthValueread-writecurrent
coiOptThreshRXPowerEnableMin
OBJECT-TYPE
This object is used to configure the enablement of the threshold min Receive power for the interface.
1.3.6.1.4.1.9.9.828.1.2.1.1.23TruthValueread-writecurrent
coiOptThreshOSNREnableMin
OBJECT-TYPE
This object is used to configure the enablement of the threshold min Optical Signal to Noise Ratio for the interface.
1.3.6.1.4.1.9.9.828.1.2.1.1.24TruthValueread-writecurrent
coiOptThreshChromaticDispersionEnableMin
OBJECT-TYPE
This object is used to configure the enablement of the threshold min measure of spread of light pulse for the interface.
1.3.6.1.4.1.9.9.828.1.2.1.1.25TruthValueread-writecurrent
coiOptThreshDifferentialGroupDelayEnableMin
OBJECT-TYPE
This object is used to configure the enablement of the threshold min propagation time difference between eigenmodes X and Y for the interface.
1.3.6.1.4.1.9.9.828.1.2.1.1.26TruthValueread-writecurrent
coiOptThreshSecondOrderPMDEnableMin
OBJECT-TYPE
This object is used to configure the enablement of the threshold min Second Order Polarization Mode Dispersion for the interface.
1.3.6.1.4.1.9.9.828.1.2.1.1.27TruthValueread-writecurrent
coiOptThreshPolarizationDependentLossEnableMin
OBJECT-TYPE
This object is used to configure the enablement of the threshold min Polarization Dependent Loss for the interface.
1.3.6.1.4.1.9.9.828.1.2.1.1.28TruthValueread-writecurrent
coiOptThreshPolarizationChangeRateEnableMin
OBJECT-TYPE
This object is used to configure the enablement of the threshold min Polarization Change Rate for the interface.
1.3.6.1.4.1.9.9.828.1.2.1.1.29TruthValueread-writecurrent
coiOptThreshPhaseNoiseEnableMin
OBJECT-TYPE
This object is used to configure the enablement of the threshold min Fluctuations in the Phase of a Waveform for the interface.
1.3.6.1.4.1.9.9.828.1.2.1.1.30TruthValueread-writecurrent
coiOptThreshLBCEnableMin
OBJECT-TYPE
This object is used to configure the enablement of the threshold min Laser Bias Current for the interface.
1.3.6.1.4.1.9.9.828.1.2.1.1.31TruthValueread-writecurrent
coiOptThreshTXPowerEnableMax
OBJECT-TYPE
This object is used to configure the enablement of the threshold max Transmit power for the interface.
1.3.6.1.4.1.9.9.828.1.2.1.1.32TruthValueread-writecurrent
coiOptThreshRXPowerEnableMax
OBJECT-TYPE
This object is used to configure the enablement of the threshold max Receive power for the interface.
1.3.6.1.4.1.9.9.828.1.2.1.1.33TruthValueread-writecurrent
coiOptThreshOSNREnableMax
OBJECT-TYPE
This object is used to configure the enablement of the threshold max Optical Signal to Noise Ratio for the interface.
1.3.6.1.4.1.9.9.828.1.2.1.1.34TruthValueread-writecurrent
coiOptThreshChromaticDispersionEnableMax
OBJECT-TYPE
This object is used to configure the enablement of the threshold max measure of spread of light pulse for the interface.
1.3.6.1.4.1.9.9.828.1.2.1.1.35TruthValueread-writecurrent
coiOptThreshDifferentialGroupDelayEnableMax
OBJECT-TYPE
This object is used to configure the enablement of the threshold max propagation time difference between eigenmodes X and Y for the interface.
1.3.6.1.4.1.9.9.828.1.2.1.1.36TruthValueread-writecurrent
coiOptThreshSecondOrderPMDEnableMax
OBJECT-TYPE
This object is used to configure the enablement of the threshold max Second Order Polarization Mode Dispersion for the interface.
1.3.6.1.4.1.9.9.828.1.2.1.1.37TruthValueread-writecurrent
coiOptThreshPolarizationDependentLossEnableMax
OBJECT-TYPE
This object is used to configure the enablement of the threshold max Polarization Dependent Loss for the interface.
1.3.6.1.4.1.9.9.828.1.2.1.1.38TruthValueread-writecurrent
coiOptThreshPolarizationChangeRateEnableMax
OBJECT-TYPE
This object is used to configure the enablement of the threshold max Polarization Change Rate for the interface.
1.3.6.1.4.1.9.9.828.1.2.1.1.39TruthValueread-writecurrent
coiOptThreshPhaseNoiseEnableMax
OBJECT-TYPE
This object is used to configure the enablement of the threshold max Fluctuations in the Phase of a Waveform for the interface.
1.3.6.1.4.1.9.9.828.1.2.1.1.40TruthValueread-writecurrent
coiOptThreshLBCEnableMax
OBJECT-TYPE
This object is used to configure the enablement of the threshold max Laser Bias Current for the interface.
1.3.6.1.4.1.9.9.828.1.2.1.1.41TruthValueread-writecurrent
coiOpticalCurrentTable
OBJECT-TYPE
This table provides current information for optical layer related attributes of interfaces with an ifType of opticalChannel(195), Lane as coiOptCurrentLane and Interval as coiOptCurrentIntervalType.
1.3.6.1.4.1.9.9.828.1.2.2not-accessiblecurrent
coiOpticalCurrentEntry
OBJECT-TYPE
An entry containing current information on optical layer related attributes of interfaces with an ifType opticalChannel(195). Entries are created by the feature when a new interface is added to the ifTable.
1.3.6.1.4.1.9.9.828.1.2.2.1not-accessiblecurrent
coiOptCurrentLane
OBJECT-TYPE
This object specifies the lane number for the optical interface. Each optical controller is divided into data lanes with each lane operating at some data rate, giving an aggregated bandwidth of the controller as a whole. Lane is applicable for breakout mode of operation.
1.3.6.1.4.1.9.9.828.1.2.2.1.1Integer32 (1..12)not-accessiblecurrent
coiOptCurrentIntervalType
OBJECT-TYPE
This object gives the interval type during which the current performance statistics are accumulated.
1.3.6.1.4.1.9.9.828.1.2.2.1.2CoiIntervalTypenot-accessiblecurrent
coiOptCurrentTXPowerMax
OBJECT-TYPE
This object specifies the current max Transmit power for the interface in 1/100 dBm.
1.3.6.1.4.1.9.9.828.1.2.2.1.3CoiOpticalPowerread-onlycurrent
coiOptCurrentRXPowerMax
OBJECT-TYPE
This object specifies the current max Receive power for the interface in 1/100 dBm.
1.3.6.1.4.1.9.9.828.1.2.2.1.4CoiOpticalPowerread-onlycurrent
coiOptCurrentOSNRMax
OBJECT-TYPE
This object specifies the current max Optical Signal to Noise Ratio for the interface in 1/100 dB.
1.3.6.1.4.1.9.9.828.1.2.2.1.5Integer32read-onlycurrent
coiOptCurrentChromaticDispersionMax
OBJECT-TYPE
This object specifies the current max measure of spread of light pulse for the interface in ps/nm.
1.3.6.1.4.1.9.9.828.1.2.2.1.6Integer32read-onlycurrent
coiOptCurrentDifferentialGroupDelayMax
OBJECT-TYPE
This object specifies the current max propagation time difference between eigenmodes X and Y for the interface in 1/100 ps.
1.3.6.1.4.1.9.9.828.1.2.2.1.7Integer32read-onlycurrent
coiOptCurrentSecondOrderPMDMax
OBJECT-TYPE
This object specifies the current max Second Order Polarization Mode Dispersion for the interface in 1/100 ps^2.
1.3.6.1.4.1.9.9.828.1.2.2.1.8Integer32read-onlycurrent
coiOptCurrentPolarizationDependentLossMax
OBJECT-TYPE
This object specifies the current max Polarization Dependent Loss for the interface in 1/100 dB.
1.3.6.1.4.1.9.9.828.1.2.2.1.9Integer32read-onlycurrent
coiOptCurrentPolarizationChangeRateMax
OBJECT-TYPE
This object specifies the current max Polarization Change Rate for the interface in 1/100 rad/s.
1.3.6.1.4.1.9.9.828.1.2.2.1.10Integer32read-onlycurrent
coiOptCurrentPhaseNoiseMax
OBJECT-TYPE
This object specifies the current max Fluctuations in the Phase of a Waveform for the interface in 1/1000 dB.
1.3.6.1.4.1.9.9.828.1.2.2.1.11Integer32read-onlycurrent
coiOptCurrentLBCMax
OBJECT-TYPE
This object specifies the current max Laser Bias Current in 1/10% for the interface.
1.3.6.1.4.1.9.9.828.1.2.2.1.12Integer32 (0..1000)read-onlycurrent
coiOptCurrentTXPowerMin
OBJECT-TYPE
This object specifies the current min Transmit power for the interface in 1/100 dBm.
1.3.6.1.4.1.9.9.828.1.2.2.1.13CoiOpticalPowerread-onlycurrent
coiOptCurrentRXPowerMin
OBJECT-TYPE
This object specifies the current min Receive power for the interface in 1/100 dBm.
1.3.6.1.4.1.9.9.828.1.2.2.1.14CoiOpticalPowerread-onlycurrent
coiOptCurrentOSNRMin
OBJECT-TYPE
This object specifies the current min Optical Signal to Noise Ratio for the interface in 1/100 dB.
1.3.6.1.4.1.9.9.828.1.2.2.1.15Integer32read-onlycurrent
coiOptCurrentChromaticDispersionMin
OBJECT-TYPE
This object specifies the current min measure of spread of light pulse for the interface in ps/nm.
1.3.6.1.4.1.9.9.828.1.2.2.1.16Integer32read-onlycurrent
coiOptCurrentDifferentialGroupDelayMin
OBJECT-TYPE
This object specifies the current min propagation time difference between eigenmodes X and Y for the interface in 1/100 ps.
1.3.6.1.4.1.9.9.828.1.2.2.1.17Integer32read-onlycurrent
coiOptCurrentSecondOrderPMDMin
OBJECT-TYPE
This object specifies the current min Second Order Polarization Mode Dispersion for the interface in 1/100 ps^2.
1.3.6.1.4.1.9.9.828.1.2.2.1.18Integer32read-onlycurrent
coiOptCurrentPolarizationDependentLossMin
OBJECT-TYPE
This object specifies the current min Polarization Dependent Loss for the interface in 1/100 dB.
1.3.6.1.4.1.9.9.828.1.2.2.1.19Integer32read-onlycurrent
coiOptCurrentPolarizationChangeRateMin
OBJECT-TYPE
This object specifies the current min Polarization Change Rate for the interface in 1/100 rad/s.
1.3.6.1.4.1.9.9.828.1.2.2.1.20Integer32read-onlycurrent
coiOptCurrentPhaseNoiseMin
OBJECT-TYPE
This object specifies the current min Fluctuations in the Phase of a Waveform in 1/1000 dB for the interface.
1.3.6.1.4.1.9.9.828.1.2.2.1.21Integer32read-onlycurrent
coiOptCurrentLBCMin
OBJECT-TYPE
This object specifies the current min Laser Bias Current in 1/10% for the interface.
1.3.6.1.4.1.9.9.828.1.2.2.1.22Integer32 (0..1000)read-onlycurrent
coiOptCurrentTXPowerAvg
OBJECT-TYPE
This object specifies the current average Transmit power for the interface in 1/100 dBm.
1.3.6.1.4.1.9.9.828.1.2.2.1.23CoiOpticalPowerread-onlycurrent
coiOptCurrentRXPowerAvg
OBJECT-TYPE
This object specifies the current average Receive power for the interface in 1/100 dBm.
1.3.6.1.4.1.9.9.828.1.2.2.1.24CoiOpticalPowerread-onlycurrent
coiOptCurrentOSNRAvg
OBJECT-TYPE
This object specifies the current average Optical Signal to Noise Ratio for the interface in 1/100 dB.
1.3.6.1.4.1.9.9.828.1.2.2.1.25Integer32read-onlycurrent
coiOptCurrentChromaticDispersionAvg
OBJECT-TYPE
This object specifies the current average measure of spread of light pulse for the interface in ps/nm.
1.3.6.1.4.1.9.9.828.1.2.2.1.26Integer32read-onlycurrent
coiOptCurrentDifferentialGroupDelayAvg
OBJECT-TYPE
This object specifies the current average propagation time difference between eigenmodes X and Y for the interface in 1/100 ps.
1.3.6.1.4.1.9.9.828.1.2.2.1.27Integer32read-onlycurrent
coiOptCurrentSecondOrderPMDAvg
OBJECT-TYPE
This object specifies the current average Second Order Polarization Mode Dispersion for the interface in 1/100 ps^2.
1.3.6.1.4.1.9.9.828.1.2.2.1.28Integer32read-onlycurrent
coiOptCurrentPolarizationDependentLossAvg
OBJECT-TYPE
This object specifies the current average Polarization Dependent Loss for the interface in 1/100 dB.
1.3.6.1.4.1.9.9.828.1.2.2.1.29Integer32read-onlycurrent
coiOptCurrentPolarizationChangeRateAvg
OBJECT-TYPE
This object specifies the current average Polarization Change Rate for the interface in 1/100 rad/s.
1.3.6.1.4.1.9.9.828.1.2.2.1.30Integer32read-onlycurrent
coiOptCurrentPhaseNoiseAvg
OBJECT-TYPE
This object specifies the current average Fluctuations in the Phase of a Waveform in 1/1000 dB for the interface.
1.3.6.1.4.1.9.9.828.1.2.2.1.31Integer32read-onlycurrent
coiOptCurrentLBCAvg
OBJECT-TYPE
This object specifies the current average Laser Bias Current in 1/10% for the interface.
1.3.6.1.4.1.9.9.828.1.2.2.1.32Integer32 (0..1000)read-onlycurrent
coiOptCurrentTimestamp
OBJECT-TYPE
This object specifies the timestamp for the current bucket for the interface.
1.3.6.1.4.1.9.9.828.1.2.2.1.33OCTET STRINGread-onlycurrent
coiOpticalIntervalTable
OBJECT-TYPE
This table provides interval information for optical layer related attributes of interfaces with an ifType of opticalChannel(195), lane as coiOptIntervalLane, Interval as coiOptIntervalIntervalType and history bucket as coiOptIntervalIntervalType.
1.3.6.1.4.1.9.9.828.1.2.3not-accessiblecurrent
coiOpticalIntervalEntry
OBJECT-TYPE
An entry containing interval information on optical layer related attributes of interfaces with an ifType opticalChannel(195). Entries are created by the feature when a new interface is added to the ifTable.
1.3.6.1.4.1.9.9.828.1.2.3.1not-accessiblecurrent
coiOptIntervalLane
OBJECT-TYPE
This object specifies the lane number for the optical interface. Each optical controller is divided into data lanes with each lane operating at some data rate, giving an aggregated bandwidth of the controller as a whole.Lane is applicable for breakout mode of operation.
1.3.6.1.4.1.9.9.828.1.2.3.1.1Integer32 (1..12)not-accessiblecurrent
coiOptIntervalIntervalType
OBJECT-TYPE
This object gives the interval type during which the performance statistics are accumulated.
1.3.6.1.4.1.9.9.828.1.2.3.1.2CoiIntervalTypenot-accessiblecurrent
coiOptIntervalNum
OBJECT-TYPE
This object identifies the interval for which the set of interval performance values is available. The interval identified by 1 is the most recent 15 minute or 24 hour interval, and the interval identified by N is the interval immediately preceding the one identified by N-1.
1.3.6.1.4.1.9.9.828.1.2.3.1.3Integer32 (1..32)not-accessiblecurrent
coiOptIntervalTXPowerMax
OBJECT-TYPE
This object specifies the interval maximum Transmit power in 1/100 dBm for the interface.
1.3.6.1.4.1.9.9.828.1.2.3.1.4CoiOpticalPowerread-onlycurrent
coiOptIntervalRXPowerMax
OBJECT-TYPE
This object specifies the interval maximum Receive power in 1/100 dBm for the interface.
1.3.6.1.4.1.9.9.828.1.2.3.1.5CoiOpticalPowerread-onlycurrent
coiOptIntervalOSNRMax
OBJECT-TYPE
This object specifies the interval maximum Optical Signal to Noise Ratio in 1/100 dB for the interface.
1.3.6.1.4.1.9.9.828.1.2.3.1.6Integer32read-onlycurrent
coiOptIntervalChromaticDispersionMax
OBJECT-TYPE
This object specifies the interval maximum measure of spread of light pulse for the interface in ps/nm.
1.3.6.1.4.1.9.9.828.1.2.3.1.7Integer32read-onlycurrent
coiOptIntervalDifferentialGroupDelayMax
OBJECT-TYPE
This object specifies the interval maximum propagation time difference between eigenmodes X and Y for the interface in 1/100 ps.
1.3.6.1.4.1.9.9.828.1.2.3.1.8Integer32read-onlycurrent
coiOptIntervalSecondOrderPMDMax
OBJECT-TYPE
This object specifies the interval maximum Second Order Polarization Mode Dispersion in 1/100 ps^2 for the interface.
1.3.6.1.4.1.9.9.828.1.2.3.1.9Integer32read-onlycurrent
coiOptIntervalPolarizationDependentLossMax
OBJECT-TYPE
This object specifies the interval maximum Polarization Dependent Loss in 1/100 dB for the interface.
1.3.6.1.4.1.9.9.828.1.2.3.1.10Integer32read-onlycurrent
coiOptIntervalPolarizationChangeRateMax
OBJECT-TYPE
This object specifies the interval maximum Polarization Change Rate in 1/100 rad/s for the interface.
1.3.6.1.4.1.9.9.828.1.2.3.1.11Integer32read-onlycurrent
coiOptIntervalPhaseNoiseMax
OBJECT-TYPE
This object specifies the interval maximum Fluctuations in the Phase of a Waveform in 1/1000 dB for the interface.
1.3.6.1.4.1.9.9.828.1.2.3.1.12Integer32read-onlycurrent
coiOptIntervalLBCMax
OBJECT-TYPE
This object specifies the interval maximum Laser Bias Current in 1/10% for the interface.
1.3.6.1.4.1.9.9.828.1.2.3.1.13Integer32read-onlycurrent
coiOptIntervalTXPowerMin
OBJECT-TYPE
This object specifies the interval minimum Transmit power in 1/100 dBm for the interface.
1.3.6.1.4.1.9.9.828.1.2.3.1.14CoiOpticalPowerread-onlycurrent
coiOptIntervalRXPowerMin
OBJECT-TYPE
This object specifies the interval minimum Receive power in 1/100 dBm for the interface.
1.3.6.1.4.1.9.9.828.1.2.3.1.15CoiOpticalPowerread-onlycurrent
coiOptIntervalOSNRMin
OBJECT-TYPE
This object specifies the interval minimum Optical Signal to Noise Ratio in 1/100 dB for the interface.
1.3.6.1.4.1.9.9.828.1.2.3.1.16Integer32read-onlycurrent
coiOptIntervalChromaticDispersionMin
OBJECT-TYPE
This object specifies the interval minimum measure of spread of light pulse in ps/nm for the interface.
1.3.6.1.4.1.9.9.828.1.2.3.1.17Integer32read-onlycurrent
coiOptIntervalDifferentialGroupDelayMin
OBJECT-TYPE
This object specifies the interval minimum propagation time difference between eigenmodes X and Y in 1/100 ps for the interface.
1.3.6.1.4.1.9.9.828.1.2.3.1.18Integer32read-onlycurrent
coiOptIntervalSecondOrderPMDMin
OBJECT-TYPE
This object specifies the interval minimum Second Order Polarization Mode Dispersion in 1/100 ps^2 for the interface.
1.3.6.1.4.1.9.9.828.1.2.3.1.19Integer32read-onlycurrent
coiOptIntervalPolarizationDependentLossMin
OBJECT-TYPE
This object specifies the interval minimum Polarization Dependent Loss in 1/100 dB for the interface.
1.3.6.1.4.1.9.9.828.1.2.3.1.20Integer32read-onlycurrent
coiOptIntervalPolarizationChangeRateMin
OBJECT-TYPE
This object specifies the interval minimum Polarization Change Rate in 1/100 rad/s for the interface.
1.3.6.1.4.1.9.9.828.1.2.3.1.21Integer32read-onlycurrent
coiOptIntervalPhaseNoiseMin
OBJECT-TYPE
This object specifies the interval minimum Fluctuations in the Phase of a Waveform in 1/1000 dB for the interface.
1.3.6.1.4.1.9.9.828.1.2.3.1.22Integer32read-onlycurrent
coiOptIntervalLBCMin
OBJECT-TYPE
This object specifies the interval minimum Laser Bias Current in 1/10% for the interface.
1.3.6.1.4.1.9.9.828.1.2.3.1.23Integer32read-onlycurrent
coiOptIntervalTXPowerAvg
OBJECT-TYPE
This object specifies the interval average Transmit power in 1/100 dBm for the interface.
1.3.6.1.4.1.9.9.828.1.2.3.1.24CoiOpticalPowerread-onlycurrent
coiOptIntervalRXPowerAvg
OBJECT-TYPE
This object specifies the interval average Receive power in 1/100 dBm for the interface.
1.3.6.1.4.1.9.9.828.1.2.3.1.25CoiOpticalPowerread-onlycurrent
coiOptIntervalOSNRAvg
OBJECT-TYPE
This object specifies the interval average Optical Signal to Noise Ratio in 1/100 dB for the interface.
1.3.6.1.4.1.9.9.828.1.2.3.1.26Integer32read-onlycurrent
coiOptIntervalChromaticDispersionAvg
OBJECT-TYPE
This object specifies the interval average measure of spread of light pulse in ps/nm for the interface.
1.3.6.1.4.1.9.9.828.1.2.3.1.27Integer32read-onlycurrent
coiOptIntervalDifferentialGroupDelayAvg
OBJECT-TYPE
This object specifies the interval average propagation time difference between eigenmodes X and Y in 1/100 ps for the interface.
1.3.6.1.4.1.9.9.828.1.2.3.1.28Integer32read-onlycurrent
coiOptIntervalSecondOrderPMDAvg
OBJECT-TYPE
This object specifies the interval average Second Order Polarization Mode Dispersion in 1/100 ps^2 for the interface.
1.3.6.1.4.1.9.9.828.1.2.3.1.29Integer32read-onlycurrent
coiOptIntervalPolarizationDependentLossAvg
OBJECT-TYPE
This object specifies the interval average Polarization Dependent Loss in 1/100 dB for the interface.
1.3.6.1.4.1.9.9.828.1.2.3.1.30Integer32read-onlycurrent
coiOptIntervalPolarizationChangeRateAvg
OBJECT-TYPE
This object specifies the interval average Polarization Change Rate in 1/100 rad/s for the interface.
1.3.6.1.4.1.9.9.828.1.2.3.1.31Integer32read-onlycurrent
coiOptIntervalPhaseNoiseAvg
OBJECT-TYPE
This object specifies the interval average Fluctuations in the Phase of a Waveform in 1/1000 dB for the interface.
1.3.6.1.4.1.9.9.828.1.2.3.1.32Integer32read-onlycurrent
coiOptIntervalLBCAvg
OBJECT-TYPE
This object specifies the interval average Laser Bias Current in 1/10 % for the interface.
1.3.6.1.4.1.9.9.828.1.2.3.1.33Integer32read-onlycurrent
coiOptIntervalTimestamp
OBJECT-TYPE
This object specifies the timestamp, for the bucket specified by 'coiOptIntervalNum', for the interface.
1.3.6.1.4.1.9.9.828.1.2.3.1.34OCTET STRINGread-onlycurrent
coiOpticalClientInfoTable
OBJECT-TYPE
This table provides management information for optical's client layer related attributes of interfaces with an ifType of ethernetCsmacd(6).This parameter is applicable only for client interfaces.
1.3.6.1.4.1.9.9.828.1.3not-accessiblecurrent
coiOpticalClientInfoEntry
OBJECT-TYPE
An entry containing information for optical's client layer related attributes of interfaces with an ifType of ethernetCsmacd(6). Entries are created by the feature when the interface discovers the neighbour's ethernet MAC Address.
1.3.6.1.4.1.9.9.828.1.3.1not-accessiblecurrent
coiOpticalClientEthernetNeighbourMAC
OBJECT-TYPE
This object gives the neighbour MAC Address to which the interface is connected.
1.3.6.1.4.1.9.9.828.1.3.1.1MacAddressread-onlycurrent
coiOpticalEquipmentAlarmGroup
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.828.1.4
coiOpticalAlarmLocation
OBJECT-TYPE
This object indicates the location of the component that raised alarm, within the device.
1.3.6.1.4.1.9.9.828.1.4.1DisplayStringaccessible-for-notifycurrent
coiOpticalAlarmType
OBJECT-TYPE
This object indicates the type of alarm that is raised.
1.3.6.1.4.1.9.9.828.1.4.2CoiOptAlarmTypeaccessible-for-notifycurrent
coiOpticalAlarmTimeStamp
OBJECT-TYPE
This object gives the time when an event occurred. This is accurate only upto a second.
1.3.6.1.4.1.9.9.828.1.4.3TimeStampaccessible-for-notifycurrent
coiOpticalAlarmName
OBJECT-TYPE
This variable gives the user-visible name, which uniquely identifies the alarm in the system.
1.3.6.1.4.1.9.9.828.1.4.4DisplayStringaccessible-for-notifycurrent
coiOpticalAlarmAdditionalInfo
OBJECT-TYPE
This variable provides additional info about the alarm. This object would be a null string if no additional information is specified.
1.3.6.1.4.1.9.9.828.1.4.5DisplayStringaccessible-for-notifycurrent
coiOpticalAlarmSeverity
OBJECT-TYPE
This variable specifies alarm severity.
1.3.6.1.4.1.9.9.828.1.4.6CoiOptAlarmSeverityaccessible-for-notifycurrent
coiOpticalAlarmStatus
OBJECT-TYPE
This variable specifies alarm status.
1.3.6.1.4.1.9.9.828.1.4.7CoiOptAlarmStatusaccessible-for-notifycurrent
coiOpticalAlarmServiceAffecting
OBJECT-TYPE
This variable specifies the service affecting state of the alarm.
1.3.6.1.4.1.9.9.828.1.4.8CoiOptAlarmServiceAffectingaccessible-for-notifycurrent
ciscoOpticalMIBConformance
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.828.2
ciscoOpticalMIBCompliances
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.828.2.1
ciscoOpticalMIBGroups
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.828.2.2

Notifications

NameOIDStatus
coiOpticsStatusChange
NOTIFICATION-TYPE
This notification is generated whenever the defect status of Optics on an interface changes. Varbind 'ifIndex' indicates the interface whose defect status of the Optics layer has just changed. Varbind 'ifName' indicates the interface Name whose defect status of the Optics layer has just changed. Varbind 'coiOpticalControllerPortType' indicates the port type of the interface whose defect status of the Optics layer has just changed. Varbind 'coiOpticalControllerStatus' indicates the current defect status of the Optics layer on the interface.
1.3.6.1.4.1.9.9.828.0.1current
coiOpticalEquipmentAlarm
NOTIFICATION-TYPE
This notification is generated whenever the optical equipment alarm is generated. Varbind 'coiOpticalAlarmLocation' indicates the location on which equipment failed alarm has generated. Varbind 'coiOpticalAlarmType' indicates the type of alarm. Varbind 'coiOpticalAlarmTimeStamp' indicates the timestamp when alarm is generated. Varbind 'coiOpticalAlarmName' indicates the alarm object. Varbind 'coiOpticalAlarmAdditionalInfo' indicates additional info related to the alarm. Varbind 'coiOpticalAlarmSeverity' indicates the severity of the alarm. Varbind 'coiOpticalAlarmStatus' indicates status of the alarm. Varbind 'coiOpticalAlarmServiceAffecting' indicates the service affected state when alarm is generated.
1.3.6.1.4.1.9.9.828.0.2current

Conformance

NameOIDStatus
ciscoOpticalMIBCompliance
MODULE-COMPLIANCE
The compliance statement for platforms that monitor the parameters for the optical interfaces.
1.3.6.1.4.1.9.9.828.2.1.1deprecated
ciscoOpticalMIBComplianceRev1
MODULE-COMPLIANCE
The compliance statement for platforms that monitor the parameters for the optical interfaces.
1.3.6.1.4.1.9.9.828.2.1.2current
coiOpticalGroup
OBJECT-GROUP
The collection of objects to give information related to the optical layer characteristics for interfaces of ifType opticalChannel(195).
1.3.6.1.4.1.9.9.828.2.2.1current
coiOpticalControllerGroup
OBJECT-GROUP
The collection of objects to allow configurations and give information related to the optical layer characteristics for interfaces of ifType opticalChannel(195).
1.3.6.1.4.1.9.9.828.2.2.2current
coiOpticalControllerPerLaneGroup
OBJECT-GROUP
The collection of objects to give information related to the optical layer characteristics for interfaces of ifType opticalChannel(195) and lane number as coiOpticalControllerLane.
1.3.6.1.4.1.9.9.828.2.2.3current
coiOpticalClientInfoGroup
OBJECT-GROUP
The collection of objects to give information related to optical's client layer related attributes of interfaces with an ifType of ethernetCsmacd(6).
1.3.6.1.4.1.9.9.828.2.2.4current
coiOpticalThresholdGroup
OBJECT-GROUP
The collection of objects used for monitoring the threshold information for optical layer related attributes of interfaces with an ifType of opticalChannel(195).
1.3.6.1.4.1.9.9.828.2.2.5current
coiOpticalCurrentGroup
OBJECT-GROUP
The collection of objects used for monitoring the current information for optical layer related attributes of interfaces with an ifType of opticalChannel(195) in a current interval.
1.3.6.1.4.1.9.9.828.2.2.6current
coiOpticalIntervalGroup
OBJECT-GROUP
The collection of objects used for monitoring the interval information for optical layer related attributes of interfaces with an ifType of opticalChannel(195) in a given interval.
1.3.6.1.4.1.9.9.828.2.2.7current
coiOpticalNotifEnableGroup
OBJECT-GROUP
The collection of objects to enable the notification generations upon an interface's defect status change on optics layer.
1.3.6.1.4.1.9.9.828.2.2.8current
coiOpticalNotifStatusObjectGroup
OBJECT-GROUP
The object to be included in an Optical interface's defect status change notification.
1.3.6.1.4.1.9.9.828.2.2.9current
coiOpticalNotifGroup
NOTIFICATION-GROUP
The optical status change notifications whenever the defect status of optical layer on an interface changes.
1.3.6.1.4.1.9.9.828.2.2.10current
coiOpticalEquipmentAlarmInfoGroup
OBJECT-GROUP
The optical equipment notifications whenever the alarm is generated.
1.3.6.1.4.1.9.9.828.2.2.11current
coiOpticalPowerGroup
OBJECT-GROUP
The collection of objects used for monitoring the total power information for optical layer related attributes of interfaces with an ifType of opticalChannel(195).
1.3.6.1.4.1.9.9.828.2.2.12current