MIBs Depot

CISCO-LWAPP-REAP-MIB

Registered at
1.3.6.1.4.1.9.9.517
Last updated
2010-10-06 00:00
Organization
Cisco Systems Inc.
Revisions
2010-10-06 00:00, 2010-02-06 00:00, 2007-11-01 00:00, 2007-04-19 00:00, 2006-04-19 00:00
Namespace
cisco
Source file
CISCO-LWAPP-REAP-MIB
Digest
sha256:2a3ad6f7824244f76a553eff9bb29a4b6a6702ac4f93e7bc210cf9c5a398ebbf

Description

This MIB is intended to be implemented on all those devices operating as Central Controllers (CC) that terminate the Light Weight Access Point Protocol tunnel from Light-weight LWAPP Access Points. Information represented by this MIB is passed by the controller to those Cisco LWAPP APs, that can operate in stand-alone mode. The relationship between CC and the LWAPP APs can be depicted as follows: +......+ +......+ +......+ +......+ + + + + + + + + + CC + + CC + + CC + + CC + + + + + + + + + +......+ +......+ +......+ +......+ .. . . . .. . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + AP + + AP + + AP + + AP + + AP + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ . . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + MN + + MN + + MN + + MN + + MN + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard. LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters, to the LWAPP APs. The APs then encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller. GLOSSARY Access Point ( AP ) An entity that contains an 802.11 medium access control ( MAC ) and physical layer ( PHY ) interface and provides access to the distribution services via the wireless medium for associated clients. LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends them to the controller to which it is logically connected. Central Controller ( CC ) The central entity that terminates the LWAPP protocol tunnel from the LWAPP APs. Throughout this MIB, this entity is also referred to as 'controller'. Light Weight Access Point Protocol ( LWAPP ) This is a generic protocol that defines the communication between the Access Points and the Central Controller. Mobile Node ( MN ) A roaming 802.11 wireless device in a wireless network associated with an access point. Native VLAN ID A switch port and/or AP can be configured with a 'native VLAN ID'. Untagged or priority-tagged frames are implicitly associated with the native VLAN ID. The default native VLAN ID is '1' if VLAN tagging is enabled. The native VLAN ID is '0' or 'no VLAN ID' if VLAN tagging is not enabled. Remote Edge Access Point ( REAP ) The LWAPP AP that can also act as a stand-alone AP when it loses communication with the controller it was associated with. When REAP can reach the controller (connected state), it gets help from controller to complete client authentication. When a controller is not reachable by REAP, it goes into standalone state and does client authentication by itself. All data packets from clients are either bridged locally (local-switch) or forwarded to the controller (central-switch) depending on the WLAN configuration. Virtual LAN VLAN defined in the IEEE 802.1Q VLAN standard supports logically segmenting of LAN infrastructure into different subnets or workgroups so that packets are switched only between ports within the same VLAN. VLAN ID Each VLAN is identified by a 12-bit 'VLAN ID'. A VLAN ID of '0' is used to indicate 'no VLAN ID'. Valid VLAN IDs range from '1' to '4095'. Home AP A REAP AP can be installed at end-user home. Home AP ethernet port will be connected to DSL or cable modem at home. Home AP will be primed with Controller IP Address so that it will join with controller. REFERENCE [1] Part 11 Wireless LAN Medium Access Control ( MAC ) and Physical Layer ( PHY ) Specifications [2] Draft-obara-capwap-lwapp-00.txt, IETF Light Weight Access Point Protocol

Contact

Cisco Systems, Customer Service Postal: 170 West Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS Email: cs-wnbu-snmp@cisco.com

Imports

FromSymbols
CISCO-LWAPP-AP-MIBcLApSysMacAddress
CISCO-LWAPP-WLAN-MIBcLWlanIndex
CISCO-SMIciscoMgmt
INET-ADDRESS-MIBInetAddress, InetAddressType
SNMP-FRAMEWORK-MIBSnmpAdminString
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP
SNMPv2-SMIMODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, Unsigned32, iso
SNMPv2-TCDisplayString, RowStatus, StorageType, TEXTUAL-CONVENTION, TruthValue

Imported by

Nothing in this corpus imports this module.

Load order

Every file a consumer needs in order to load this module, dependencies first.

CISCO-LWAPP-AP-MIB
CISCO-LWAPP-DOT11-MIB
CISCO-LWAPP-REAP-MIB
CISCO-LWAPP-RF-MIB
CISCO-LWAPP-TC-MIB
CISCO-LWAPP-WLAN-MIB
CISCO-SMI
CISCO-TC
ENTITY-MIB
IANA-ENTITY-MIB
IANAifType-MIB
INET-ADDRESS-MIB
SNMP-FRAMEWORK-MIB
SNMPv2-CONF
SNMPv2-SMI
SNMPv2-TC
UUID-TC-MIB

Objects

NameOIDSyntaxAccessStatus
ciscoLwappReapMIBNotifs
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.517.0
ciscoLwappReapMIBObjects
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.517.1
ciscoLwappReapWlanConfig
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.517.1.1
cLReapWlanConfigTable
OBJECT-TYPE
This table represents the WLAN configuration sent by the controller to REAPs so that the APs can operate in stand-alone mode. LWAPP APs operating in REAP mode locally switch the data frames of the associated clients, rather than tunneling them through to the LWAPP controller as LWAPP data packets. The LWAPP controller passes this configuration set to the LWAPP AP during the AP initialization so that the AP can operate in stand-alone mode when it fails to reach the controller. The configuration is also passed to the REAP when they are individually modified through separate LWAPP messages. The REAP updates itself with the information received through these LWAPP messages. This table has a one-to-one relationship with cLWlanConfigTable of the CISCO-LWAPP-WLAN-MIB. There exist a row in this table corresponding to each row representing a WLAN in cLWlanConfigTable. Note that the configuration represented by this table is applicable only for REAPs. The controller will send this configuration set only to the REAP APs for their operation in standalone mode.
1.3.6.1.4.1.9.9.517.1.1.1not-accessiblecurrent
cLReapWlanConfigEntry
OBJECT-TYPE
Each entry represents a conceptual row in cLReapWlanConfigTable and corresponds to the packet switching configuration for a particular WLAN.
1.3.6.1.4.1.9.9.517.1.1.1.1not-accessiblecurrent
cLReapWlanEnLocalSwitching
OBJECT-TYPE
This object indicates the behavior of the REAP when switching the data frames of the clients associated to it through the WLAN identified by cLWlanIndex. A value of 'true' indicates that the AP, on which this WLAN is configured, may locally switch the data packets of the clients in the WLAN instead of tunneling them to the central controller for switching. A value of 'false' indicates that the AP should tunnel all the data packets of the wireless clients in the WLAN to the central controller for switching. Note that the value of 'true' will be effective only if the WLAN is configured on a REAP.
1.3.6.1.4.1.9.9.517.1.1.1.1.1TruthValueread-writecurrent
cLReapWlanClientIpLearnEnable
OBJECT-TYPE
This object indicates whether Client IP Address learning is enabled on the controller. When layer two tunneling is employed the IP learning on controller has to be disabled. Otherwise, the controller is unable to learn the client's IP address and cannot move it to the associated state. A value of 'true' indicates the controller does checks for IP sent by the HREAP AP. A value of 'false' indicates the controller does not check for IP from the locally switch HREAP AP.
1.3.6.1.4.1.9.9.517.1.1.1.1.2TruthValueread-writecurrent
cLReapWlanApAuth
OBJECT-TYPE
This object indicates the behavior of the REAP, on where to handle the authentication of the client associated to the wlan indicated by cLWlanIndex. A value of 'true' indicates that the AP, on which this WLAN is configured, will do the authentication of the clients in the WLAN locally instead of of sending them to the central controller. A value of 'false' indicates that the AP should send the information to the central controller to do the authentication of the client. Note that the value of 'true' will be effective only if the WLAN is configured on a REAP and WLAN is configured for local switching of the data.
1.3.6.1.4.1.9.9.517.1.1.1.1.3TruthValueread-writecurrent
cLReapWlanVlanCentralSwitching
OBJECT-TYPE
This object specifies whether the AP bridges the traffic centrally. If the VLAN is not configured on the AP uplink, the AP will tunnel the traffic back to the Wireless LAN Controller (WLC) where it is registered. Then the controller will bridge the traffic into the corresponding VLAN from where it will be transported towards the next routing instance for further processing. This feature will be applicable only to locally switched WLANs
1.3.6.1.4.1.9.9.517.1.1.1.1.4TruthValueread-writecurrent
cLReapWlanDhcpCentral
OBJECT-TYPE
This object indicates the behavior of the REAP when switching the data frames of the clients associated to it through the WLAN identified by cLWlanIndex. Note that the value of 'true' will be effective only if the WLAN is configured on a REAP.
1.3.6.1.4.1.9.9.517.1.1.1.1.5TruthValueread-writecurrent
cLReapWlanDhcpOverrideDNS
OBJECT-TYPE
This object indicates the behavior of the REAP when switching the data frames of the clients associated to it through the WLAN identified by cLWlanIndex. Note that the value of 'true' will be effective only if the WLAN is configured on a REAP.
1.3.6.1.4.1.9.9.517.1.1.1.1.6TruthValueread-writecurrent
cLReapWlanNatPatEnabled
OBJECT-TYPE
This object specifies whether Network Address Translation (NAT) and Port Address Trnaslation (PAT) are enabled on this WLAN. This can be enabled only when cLReapWlanDhcpCentral is set to 'true'. Note that the value of 'true' will be effective only if the WLAN is configured as Locally Switched.
1.3.6.1.4.1.9.9.517.1.1.1.1.7TruthValueread-writecurrent
cLReapWlanAssocCentral
OBJECT-TYPE
This object indicates the behavior of the REAP when handling the (re-)association management frames from the clients through the WLAN identified by cLWlanIndex. Note that the value of 'true' will be effective only if the WLAN is configured on a REAP.
1.3.6.1.4.1.9.9.517.1.1.1.1.8TruthValueread-writecurrent
ciscoLwappReapApConfig
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.517.1.2
cLReapApConfigTable
OBJECT-TYPE
This table represents the VLAN configuration of REAPs. The agent adds a row to this table corresponding to each row representing a REAP in cLApTable of the CISCO-LWAPP-AP-MIB. The agent deletes the row either when the AP dissociates from the controller or moved out of the remote mode.
1.3.6.1.4.1.9.9.517.1.2.1not-accessiblecurrent
cLReapApConfigEntry
OBJECT-TYPE
Each entry represents a conceptual row in cLReapApConfigTable and corresponds to the VLAN configuration of a REAP.
1.3.6.1.4.1.9.9.517.1.2.1.1not-accessiblecurrent
cLReapApNativeVlanId
OBJECT-TYPE
This object defines the Native VLAN ID for the particular AP identified by cLApSysMacAddress. Note that this particular object can be modified through a Set request only if the AP is a REAP. The agent is expected to reject the attempt to set this object for APs in other modes.
1.3.6.1.4.1.9.9.517.1.2.1.1.1Unsigned32 (1..4095)read-writecurrent
cLReapApVlanEnable
OBJECT-TYPE
This object indicates the availability of Native VLAN configured through cLReapApNativeVlanId on this REAP. A value of 'true' indicates that the VLAN configured as native through cLReapApNativeVlanId is enabled on the REAP and that the REAP can reach the controller through the native VLAN. A value of 'false' indicates that the VLAN configured as native through cLReapApNativeVlanId is disabled and the REAP can't reach the controller.
1.3.6.1.4.1.9.9.517.1.2.1.1.2TruthValueread-writecurrent
cLReapHomeApEnable
OBJECT-TYPE
This object represents if this REAP AP is used as Home AP. A value of 'true' indicates that this REAP AP is a Home AP. A value of 'false' indicates that this REAP AP is not a Home AP.
1.3.6.1.4.1.9.9.517.1.2.1.1.3TruthValueread-writecurrent
cLReapApLeastLatencyJoinEnable
OBJECT-TYPE
This object represents if this REAP AP should join controller which has least latency. A value of 'true' indicates that this REAP AP will join controller which has least latency. A value of 'false' indicates that this REAP AP will not consider latency in selecting controller to join.
1.3.6.1.4.1.9.9.517.1.2.1.1.4TruthValueread-writecurrent
cLReapHomeApLocalSsidReset
OBJECT-TYPE
This object can be used to reset local SSID on a Home AP. A value of true indicates that the local SSID is to be reset. A value of false on this during set will return error. A value of false will be returned on get.
1.3.6.1.4.1.9.9.517.1.2.1.1.5TruthValueread-writecurrent
cLReapInstallMappingRadioBackhaul
OBJECT-TYPE
This object can be used to enable or disable WLANs on backhaul radio. A value of true indicates that wlan mapping would be enabled on backhaul radio. A value of false indicates that wlan mapping would be disabled on backhaul radio. This variable is significant only when AP is in Flex+Bridge mode.
1.3.6.1.4.1.9.9.517.1.2.1.1.6TruthValueread-writecurrent
cLReapApResilientMode
OBJECT-TYPE
This object can be used to enable or disable Standalone mode support on a REAP AP. A value of true indicates that Standalone mode would be enabled on backhaul radio. A value of false indicates that Standalone mode would be disabled on backhaul radio. This variable is significant only when AP is in Flex+Bridge mode.
1.3.6.1.4.1.9.9.517.1.2.1.1.7TruthValueread-writecurrent
cLReapApVlanIdTable
OBJECT-TYPE
This table defines the WLAN / VLAN Id mappings to be configured for the REAP identified by cLApSysMacAddress. VLAN Id configured through this table is passed to the respective REAP through the 'Add WLAN' LWAPP message, sent as part of the 'Configure Response message from the controller to the REAP, during the initialization of the REAP. The REAP maps the VLAN to the particular WLAN to locally switch the data packets when those APs are in standalone mode. Thus, the information added through this table is applicable for REAPs only. VLANs are configured on WLANs for which local switching of packets is enabled through cLReapWlanEnLocalSwitching. This means that a row is added to this table only if there are WLANs available on the controller with local switching enabled and the AP is a REAP.
1.3.6.1.4.1.9.9.517.1.2.2not-accessiblecurrent
cLReapApVlanIdEntry
OBJECT-TYPE
Each entry represents a conceptual row that corresponds to one WLAN / VLAN Id mapping to be applied to the REAP identified by cLApSysMacAddress.
1.3.6.1.4.1.9.9.517.1.2.2.1not-accessiblecurrent
cLReapApVlanId
OBJECT-TYPE
This object represents the VLAN ID to be mapped to the WLAN identified by cLWlanIndex.
1.3.6.1.4.1.9.9.517.1.2.2.1.1Unsigned32 (1..4095)read-createcurrent
cLReapApVlanInheritance
OBJECT-TYPE
This object represents the inheritance to be mapped to the WLAN identified by cLWlanIndex.
1.3.6.1.4.1.9.9.517.1.2.2.1.2INTEGER {ap(1), hreapGroup(2), wlan(3)}read-createcurrent
cLReapApVlanRowStatus
OBJECT-TYPE
This object represents the rowstatus of the AP level wlan vlan mappings table.
1.3.6.1.4.1.9.9.517.1.2.2.1.3RowStatusread-createcurrent
cLReapApVlanUsedBySecEthInterface
OBJECT-TYPE
This object indicates if vlan represented by cLReapApVlanId is used by any of the secondary Ethernet interface when the REAP AP is in Flex+Bridge mode.
1.3.6.1.4.1.9.9.517.1.2.2.1.4TruthValueread-onlycurrent
cLReapApVlanIdAclTable
OBJECT-TYPE
This table defines the VLAN Id- ACL mappings to be configured for the REAP identified by cLApSysMacAddress.
1.3.6.1.4.1.9.9.517.1.2.3not-accessiblecurrent
cLReapApVlanIdAclEntry
OBJECT-TYPE
Each entry represents a conceptual row that corresponds to one VLAN Id - ACL mapping to be applied to the REAP identified by cLApSysMacAddress.
1.3.6.1.4.1.9.9.517.1.2.3.1not-accessiblecurrent
cLReapVlanId
OBJECT-TYPE
This object specifies the VLAN ID to be mapped to the Acl for the Access Point identified by cLApSysMacAddress.
1.3.6.1.4.1.9.9.517.1.2.3.1.1Unsigned32 (1..4095)not-accessiblecurrent
cLReapIngressAcl
OBJECT-TYPE
This object specifies the name of the ingress Access Control List for the vlan-acl mapping.
1.3.6.1.4.1.9.9.517.1.2.3.1.2DisplayString (SIZE(0..32))read-createcurrent
cLReapEgressAcl
OBJECT-TYPE
This object specifies the name of the egress Access Control List for the vlan-acl mapping.
1.3.6.1.4.1.9.9.517.1.2.3.1.3DisplayString (SIZE(0..32))read-createcurrent
cLReapApVlanIdAclRowStatus
OBJECT-TYPE
This object specifies the status column for a conceptual row in this table.
1.3.6.1.4.1.9.9.517.1.2.3.1.4RowStatusread-createcurrent
cLReapVlanIdAclType
OBJECT-TYPE
This object specifies the type of the vlan acl mapping apSource - vlan-acl mapping applied from AP level. groupSource - vlan-acl mapping applied from hreap group level.
1.3.6.1.4.1.9.9.517.1.2.3.1.5INTEGER {apSource(1), groupSource(2)}read-onlycurrent
cLReapApWlanAclTable
OBJECT-TYPE
This table defines the WLAN ACL mappings to be configured for the REAP identified by cLApSysMacAddress. A row is added to this table only if there are WLANs available on the controller with local switching enabled and the AP is a REAP.
1.3.6.1.4.1.9.9.517.1.2.4not-accessiblecurrent
cLReapApWlanAclEntry
OBJECT-TYPE
Each entry represents a conceptual row that corresponds to one WLAN / ACL mapping to be applied to the REAP identified by cLApSysMacAddress.
1.3.6.1.4.1.9.9.517.1.2.4.1not-accessiblecurrent
cLReapApWebAuthAcl
OBJECT-TYPE
This object represents the webauth ACL name to be mapped to the WLAN identified by cLWlanIndex.
1.3.6.1.4.1.9.9.517.1.2.4.1.1SnmpAdminString (SIZE(0..32))read-writecurrent
cLReapApWebAuthAclRowStatus
OBJECT-TYPE
This object represents the status column for a conceptual row in this table.
1.3.6.1.4.1.9.9.517.1.2.4.1.2RowStatusread-createcurrent
cLReapWebPolicyAclTable
OBJECT-TYPE
This table represents the web policies associated with an AP. Entries are added or deleted by the user through the use of cLReapWebPolicyRowStatus.
1.3.6.1.4.1.9.9.517.1.2.5not-accessiblecurrent
cLReapWebPolicyAclEntry
OBJECT-TYPE
Each entry represents a conceptual row in cLReapWebPolicyAclTable.
1.3.6.1.4.1.9.9.517.1.2.5.1not-accessiblecurrent
cLReapWebPolicyAcl
OBJECT-TYPE
This object specifies the name of the web policy Access Control List to be mapped to the access point identified by cLApSysMacAddress.
1.3.6.1.4.1.9.9.517.1.2.5.1.1SnmpAdminString (SIZE(0..32))not-accessiblecurrent
cLReapWebPolicyAclRowStatus
OBJECT-TYPE
This object represents the status column for a conceptual row in this table.
1.3.6.1.4.1.9.9.517.1.2.5.1.2RowStatusread-createcurrent
cLReapApLocalSplitACLTable
OBJECT-TYPE
This table defines the WLAN - ACL mappings to be configured for the REAP identified by cLApSysMacAddress.
1.3.6.1.4.1.9.9.517.1.2.6not-accessiblecurrent
cLReapApLocalSplitACLEntry
OBJECT-TYPE
Each entry represents a conceptual row that corresponds to one WLAN- ACL mapping to be applied to the REAP identified by cLApSysMacAddress.
1.3.6.1.4.1.9.9.517.1.2.6.1not-accessiblecurrent
cLReapApLocalSplitAcl
OBJECT-TYPE
This object represents the LocalSplit ACL name to be mapped to the WLAN identified by cLWlanIndex.
1.3.6.1.4.1.9.9.517.1.2.6.1.1SnmpAdminString (SIZE(0..32))read-createcurrent
cLReapApLocalSplitAclRowStatus
OBJECT-TYPE
This object represents the status column for a conceptual row in this table.
1.3.6.1.4.1.9.9.517.1.2.6.1.2RowStatusread-createcurrent
cLReapApCentralDhcpTable
OBJECT-TYPE
1.3.6.1.4.1.9.9.517.1.2.7not-accessiblecurrent
cLReapApCentralDhcpEntry
OBJECT-TYPE
1.3.6.1.4.1.9.9.517.1.2.7.1not-accessiblecurrent
cLReapApDhcpCentral
OBJECT-TYPE
This object indicates the behavior of the REAP group when switching the data frames of the clients associated to it through the WLAN identified by cLWlanIndex.
1.3.6.1.4.1.9.9.517.1.2.7.1.1TruthValueread-writecurrent
cLReapApDhcpOverrideDNS
OBJECT-TYPE
This object indicates the behavior of the REAP group when switching the data frames of the clients associated to it through the WLAN identified by cLWlanIndex.
1.3.6.1.4.1.9.9.517.1.2.7.1.2TruthValueread-writecurrent
cLReapApNatPatEnabled
OBJECT-TYPE
This object specifies whether Network Address Translation (NAT) and Port Address Trnaslation (PAT) are enabled on this reap AP. This can be enabled only when cLReapWlanDhcpCentral is set to 'true'. Note that the value of 'true' will be effective only if the WLAN is configured as Locally Switched.
1.3.6.1.4.1.9.9.517.1.2.7.1.3TruthValueread-writecurrent
cLReapApDhcpRowStatus
OBJECT-TYPE
This object represents the status column for a conceptual row in this table.
1.3.6.1.4.1.9.9.517.1.2.7.1.4RowStatusread-createcurrent
cLReapApInheritance
OBJECT-TYPE
This object represents the inheritance level of central DHCP configuration.
1.3.6.1.4.1.9.9.517.1.2.7.1.5SnmpAdminStringread-onlycurrent
cLReapApL2AclTable
OBJECT-TYPE
This table defines the L2 ACL mappings to be configured for the FlexAP identified by cLApSysMacAddress. A row is added to this table only if there are WLANs available on the controller with local switching enabled and the AP is a REAP.
1.3.6.1.4.1.9.9.517.1.2.8not-accessiblecurrent
cLReapApL2AclEntry
OBJECT-TYPE
Each entry represents a conceptual row that corresponds to one WLAN / ACL mapping to be applied to the REAP identified by cLApSysMacAddress.
1.3.6.1.4.1.9.9.517.1.2.8.1not-accessiblecurrent
cLReapApL2Acl
OBJECT-TYPE
This object represents the L2ACL name to be mapped to the WLAN identified by cLWlanIndex for this FlexAP
1.3.6.1.4.1.9.9.517.1.2.8.1.1SnmpAdminString (SIZE(0..32))read-createcurrent
cLReapApL2AclRowStatus
OBJECT-TYPE
This object represents the status column for a conceptual row in this table.
1.3.6.1.4.1.9.9.517.1.2.8.1.2RowStatusread-createcurrent
ciscoLwappReapGroupConfig
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.517.1.3
cLReapGroupConfigTable
OBJECT-TYPE
This table represents the configuration for REAPs so that the APs can be configured as a group. Entries are added or deleted by the user through the use of cLReapGroupRowStatus.
1.3.6.1.4.1.9.9.517.1.3.1not-accessiblecurrent
cLReapGroupConfigEntry
OBJECT-TYPE
Each entry represents a conceptual row in cLReapGroupConfigTable.
1.3.6.1.4.1.9.9.517.1.3.1.1not-accessiblecurrent
cLReapGroupName
OBJECT-TYPE
This object uniquely identifies an entry in cLReapGroupConfigTable.
1.3.6.1.4.1.9.9.517.1.3.1.1.1SnmpAdminStringnot-accessiblecurrent
cLReapGroupPrimaryRadiusIndex
OBJECT-TYPE
The object represents the value that maps to the primary RADIUS server for this group. A value of 0 indicates that the primary RADIUS server is not configured for this group.
1.3.6.1.4.1.9.9.517.1.3.1.1.2Unsigned32read-createcurrent
cLReapGroupSecondaryRadiusIndex
OBJECT-TYPE
The object represents the value that maps to the secondary RADIUS server for this group. A value of 0 indicates that the primary RADIUS server is not configured for this group.
1.3.6.1.4.1.9.9.517.1.3.1.1.3Unsigned32read-createcurrent
cLReapGroupStorageType
OBJECT-TYPE
This object represents the storage type for this conceptual row.
1.3.6.1.4.1.9.9.517.1.3.1.1.4StorageTyperead-createcurrent
cLReapGroupRowStatus
OBJECT-TYPE
This object represents the status column for a conceptual row in this table.
1.3.6.1.4.1.9.9.517.1.3.1.1.5RowStatusread-createcurrent
cLReapGroupRadiusPacTimeout
OBJECT-TYPE
This object represents timeout value for the PAC (protected access credentials). Superceded by cLReapGroupRadiusPacTimeoutCtrl.
1.3.6.1.4.1.9.9.517.1.3.1.1.6Unsigned32 (0..4095)read-createdeprecated
cLReapGroupRadiusAuthorityId
OBJECT-TYPE
This object configures the authority ID.
1.3.6.1.4.1.9.9.517.1.3.1.1.7OCTET STRING (SIZE(0..32))read-createcurrent
cLReapGroupRadiusAuthorityInfo
OBJECT-TYPE
This object represents the authority information.
1.3.6.1.4.1.9.9.517.1.3.1.1.8OCTET STRING (SIZE(0..32))read-createcurrent
cLReapGroupRadiusServerKey
OBJECT-TYPE
This object represents the RADIUS server key. For security the key always returns '****'.
1.3.6.1.4.1.9.9.517.1.3.1.1.9OCTET STRING (SIZE(1..32))read-createcurrent
cLReapGroupRadiusIgnoreKey
OBJECT-TYPE
This parameter represents whether anonymous provisioning is enabled. A value of 'true' indicates the controller will ignore the key configured in cLReapGroupRadiusServerKey anonymous requests. A value of 'false' indicates that the controller will use the key configured by cLReapGroupRadiusServerKey.
1.3.6.1.4.1.9.9.517.1.3.1.1.10TruthValueread-createcurrent
cLReapGroupRadiusEnable
OBJECT-TYPE
This parameter represents whether RADIUS is enabled. A value of 'true' indicates that RADIUS is enabled. A value of 'false' indicates that RADIUS is disabled.
1.3.6.1.4.1.9.9.517.1.3.1.1.11TruthValueread-createcurrent
cLReapGroupRadiusLeapEnable
OBJECT-TYPE
This parameter represents whether LEAP is enabled. A value of 'true' indicates that LEAP is enabled. A value of 'false' indicates that LEAP is disabled.
1.3.6.1.4.1.9.9.517.1.3.1.1.12TruthValueread-createcurrent
cLReapGroupRadiusEapFastEnable
OBJECT-TYPE
This parameter represents whether EAP-FAST is enabled. A value of 'true' indicates that EAP-FAST is enabled. A value of 'false' indicates that EAP-FAST is disabled.
1.3.6.1.4.1.9.9.517.1.3.1.1.13TruthValueread-createcurrent
cLReapGroupRadiusPacTimeoutCtrl
OBJECT-TYPE
This parameter represents timeout value for the PAC (protected access credentials). Valid range of timeout is 2 to 4095, and value 0 stands for disable.
1.3.6.1.4.1.9.9.517.1.3.1.1.14Unsigned32 (0..4095)read-createcurrent
cLReapGroupEfficientApUpgradeEnable
OBJECT-TYPE
This parameter represents whether Efficient AP image upgrade is enabled. A value of 'true' indicates that Efficient AP image upgrade is enabled. A value of 'false' indicates that Efficient AP image upgrade is disabled.
1.3.6.1.4.1.9.9.517.1.3.1.1.15TruthValueread-writecurrent
cLReapGroupApUpgradeStart
OBJECT-TYPE
Upgrade start will start the Efficient AP image upgrade for the hreap group with the primary image when it is set to initiatePrimary(1), and from the backup if it is set to initiateSecondary(2). Abort of upgrade is initiated when it is set to abort(3).
1.3.6.1.4.1.9.9.517.1.3.1.1.16INTEGER {initiatePrimary(1), initiateBackup(2), abort(3)}read-writecurrent
cLReapGroupSlaveMaxRetryCount
OBJECT-TYPE
This object specifies the maximum retries the the slave has to undertake to start the download from the master in the hreap group.
1.3.6.1.4.1.9.9.517.1.3.1.1.17Unsigned32read-writecurrent
cLReapGroupPrimaryRadiusServerType
OBJECT-TYPE
Server IP Address Type of the primary radius server for the flexconnect group.
1.3.6.1.4.1.9.9.517.1.3.1.1.18InetAddressTyperead-createcurrent
cLReapGroupPrimaryRadiusServerAddress
OBJECT-TYPE
Server IP Address of the primary radius server for the flexconnect group.
1.3.6.1.4.1.9.9.517.1.3.1.1.19InetAddressread-createcurrent
cLReapGroupPrimaryRadiusServerPort
OBJECT-TYPE
Server IP Address of the primary radius server for the flexconnect group.
1.3.6.1.4.1.9.9.517.1.3.1.1.20Unsigned32read-createcurrent
cLReapGroupPrimaryServerSecret
OBJECT-TYPE
Secret of the primary radius server for the flexconnect group.
1.3.6.1.4.1.9.9.517.1.3.1.1.21DisplayStringread-createcurrent
cLReapGroupSecRadiusServerType
OBJECT-TYPE
Server IP Address Type of the secondary radius server for the flexconnect group.
1.3.6.1.4.1.9.9.517.1.3.1.1.22InetAddressTyperead-createcurrent
cLReapGroupSecRadiusServerAddress
OBJECT-TYPE
Server IP Address of the secondary radius server for the flexconnect group.
1.3.6.1.4.1.9.9.517.1.3.1.1.23InetAddressread-createcurrent
cLReapGroupSecRadiusServerPort
OBJECT-TYPE
Server IP Address of the secondary radius server for the flexconnect group.
1.3.6.1.4.1.9.9.517.1.3.1.1.24Unsigned32read-createcurrent
cLReapGroupSecServerSecret
OBJECT-TYPE
Secret of the secondary radius server for the flexconnect group.
1.3.6.1.4.1.9.9.517.1.3.1.1.25DisplayStringread-createcurrent
cLReapGroupRadiusPeapEnable
OBJECT-TYPE
This parameter represents whether PEAP is enabled. A value of 'true' indicates that PEAP is enabled. A value of 'false' indicates that PEAP is disabled.
1.3.6.1.4.1.9.9.517.1.3.1.1.26TruthValueread-createcurrent
cLReapGroupRadiusEapTlsEnable
OBJECT-TYPE
This parameter represents whether EAP-TLS is enabled. A value of 'true' indicates that EAP-TLS is enabled. A value of 'false' indicates that EAP-TLS is disabled.
1.3.6.1.4.1.9.9.517.1.3.1.1.27TruthValueread-createcurrent
cLReapGroupCertificateEapTlsEnable
OBJECT-TYPE
This parameter represents whether certificate for EAP-TLS is enabled. A value of 'true' indicates that EAP-TLS is enabled. A value of 'false' indicates that EAP-TLS is disabled.
1.3.6.1.4.1.9.9.517.1.3.1.1.28TruthValueread-createcurrent
cLReapGroupApConfigTable
OBJECT-TYPE
This table represents the group associated with an AP. Entries are added or deleted by the user through the use of cLReapGroupApRowStatus.
1.3.6.1.4.1.9.9.517.1.3.2not-accessiblecurrent
cLReapGroupApConfigEntry
OBJECT-TYPE
Each entry represents a conceptual row in cLReapGroupApConfigTable.
1.3.6.1.4.1.9.9.517.1.3.2.1not-accessiblecurrent
cLReapGroupApStorageType
OBJECT-TYPE
This object represents the storage type for this conceptual row.
1.3.6.1.4.1.9.9.517.1.3.2.1.1StorageTyperead-createcurrent
cLReapGroupApRowStatus
OBJECT-TYPE
This object represents the status column for a conceptual row in this table.
1.3.6.1.4.1.9.9.517.1.3.2.1.2RowStatusread-createcurrent
cLReapGroupUserConfigTable
OBJECT-TYPE
This table represents the group associated with an User. Entries are added or deleted by the application through the use of cLReapGroupUserRowStatus.
1.3.6.1.4.1.9.9.517.1.3.3not-accessiblecurrent
cLReapGroupUserConfigEntry
OBJECT-TYPE
Each entry represents a conceptual row in cLReapGroupUserConfigTable.
1.3.6.1.4.1.9.9.517.1.3.3.1not-accessiblecurrent
cLReapGroupUserName
OBJECT-TYPE
This object represents the user name for this group. user name is used for authenticating a client associated to an AP within the group.
1.3.6.1.4.1.9.9.517.1.3.3.1.1SnmpAdminString (SIZE(1..24))not-accessiblecurrent
cLReapGroupUserPassword
OBJECT-TYPE
This object represents the password for this conceptual row.
1.3.6.1.4.1.9.9.517.1.3.3.1.2SnmpAdminString (SIZE(1..64))read-createcurrent
cLReapGroupUserStorageType
OBJECT-TYPE
This object represents the storage type for this conceptual row.
1.3.6.1.4.1.9.9.517.1.3.3.1.3StorageTyperead-createcurrent
cLReapGroupUserRowStatus
OBJECT-TYPE
This object represents the status column for a conceptual row in this table.
1.3.6.1.4.1.9.9.517.1.3.3.1.4RowStatusread-createcurrent
cLReapGroupVlanAclTable
OBJECT-TYPE
This table represents the configuration of vlan-acl mappings for REAPs.
1.3.6.1.4.1.9.9.517.1.3.4not-accessiblecurrent
cLReapGroupVlanAclEntry
OBJECT-TYPE
Each entry represents a conceptual row in cLReapGroupVlanAclTable.
1.3.6.1.4.1.9.9.517.1.3.4.1not-accessiblecurrent
cLReapGroupVlanId
OBJECT-TYPE
This object represents the VLAN ID to be mapped to the ACL for the reap group identified by cLReapGroupName
1.3.6.1.4.1.9.9.517.1.3.4.1.1Unsigned32 (1..4095)not-accessiblecurrent
cLReapGroupIngressAcl
OBJECT-TYPE
This object specifies the name of the ingress Access Control List for the vlan-acl mapping.
1.3.6.1.4.1.9.9.517.1.3.4.1.2DisplayString (SIZE(0..32))read-createcurrent
cLReapGroupEgressAcl
OBJECT-TYPE
This object specifies the name of the egress Access Control List for the vlan-acl mapping.
1.3.6.1.4.1.9.9.517.1.3.4.1.3DisplayString (SIZE(0..32))read-createcurrent
cLReapGroupVlanAclRowStatus
OBJECT-TYPE
This object represents the status column for a conceptual row in this table.
1.3.6.1.4.1.9.9.517.1.3.4.1.4RowStatusread-createcurrent
cLReapGroupVlanOrder
OBJECT-TYPE
This object represents the vlan order configuration on the group level.
1.3.6.1.4.1.9.9.517.1.3.4.1.5Unsigned32read-onlycurrent
cLReapGroupAclTable
OBJECT-TYPE
This table represents the configuration of wlan-acl mappings for REAPs.
1.3.6.1.4.1.9.9.517.1.3.5not-accessiblecurrent
cLReapGroupAclEntry
OBJECT-TYPE
Each entry represents a conceptual row in cLReapGroupAclTable.
1.3.6.1.4.1.9.9.517.1.3.5.1not-accessiblecurrent
cLReapGroupWebAuthAcl
OBJECT-TYPE
This object specifies the name of the webauth Access Control List for the wlan-acl mapping.
1.3.6.1.4.1.9.9.517.1.3.5.1.1SnmpAdminString (SIZE(0..32))read-createcurrent
cLReapGroupAclRowStatus
OBJECT-TYPE
This object represents the status column for a conceptual row in this table.
1.3.6.1.4.1.9.9.517.1.3.5.1.2RowStatusread-createcurrent
cLReapGroupWebPolicyAclTable
OBJECT-TYPE
This table represents the configuration of webpolicy acl mappings for REAP groups.
1.3.6.1.4.1.9.9.517.1.3.6not-accessiblecurrent
cLReapGroupWebPolicyAclEntry
OBJECT-TYPE
Each entry represents a conceptual row in the cLReapGroupWebPolicyAclTable.
1.3.6.1.4.1.9.9.517.1.3.6.1not-accessiblecurrent
cLReapGroupWebPolicyAcl
OBJECT-TYPE
This object specifies the name of the webpolicy Access Control List to be mapped to the REAP group.
1.3.6.1.4.1.9.9.517.1.3.6.1.1SnmpAdminString (SIZE(0..32))not-accessiblecurrent
cLReapGroupWebPolicyAclRowStatus
OBJECT-TYPE
This object represents the status column for a conceptual row in this table.
1.3.6.1.4.1.9.9.517.1.3.6.1.2RowStatusread-createcurrent
cLReapGroupLocalSplitAclTable
OBJECT-TYPE
This table represents the configuration of WLAN-ACL mappings for local split tunneling at REAP groups.
1.3.6.1.4.1.9.9.517.1.3.7not-accessiblecurrent
cLReapGroupLocalSplitAclEntry
OBJECT-TYPE
Each entry represents a conceptual row in cLReapGroupLocalSplitAclTable.
1.3.6.1.4.1.9.9.517.1.3.7.1not-accessiblecurrent
cLReapGroupLocalSplitAcl
OBJECT-TYPE
This object specifies the name of the LocalSplit Access Control List to be mapped to the WLAN.
1.3.6.1.4.1.9.9.517.1.3.7.1.1SnmpAdminString (SIZE(0..32))read-createcurrent
cLReapGroupLocalSplitAclRowStatus
OBJECT-TYPE
This object represents the status column for a conceptual row in this table.
1.3.6.1.4.1.9.9.517.1.3.7.1.2RowStatusread-createcurrent
cLReapGroupCentralDhcpTable
OBJECT-TYPE
This table represents the configuration of central dhcp processing for REAPs.
1.3.6.1.4.1.9.9.517.1.3.8not-accessiblecurrent
cLReapGroupCentralDhcpEntry
OBJECT-TYPE
Each entry represents a conceptual row in cLReapGroupCentralDhcpTable.
1.3.6.1.4.1.9.9.517.1.3.8.1not-accessiblecurrent
cLReapGroupDhcpCentral
OBJECT-TYPE
This object indicates the behavior of the REAP group when switching the data frames of the clients associated to it through the WLAN identified by cLWlanIndex.
1.3.6.1.4.1.9.9.517.1.3.8.1.1TruthValueread-writecurrent
cLReapGroupDhcpOverrideDNS
OBJECT-TYPE
This object indicates the behavior of the REAP group when switching the data frames of the clients associated to it through the WLAN identified by cLWlanIndex.
1.3.6.1.4.1.9.9.517.1.3.8.1.2TruthValueread-writecurrent
cLReapGroupNatPatEnabled
OBJECT-TYPE
This object specifies whether Network Address Translation (NAT) and Port Address Trnaslation (PAT) are enabled on this reap group. This can be enabled only when cLReapWlanDhcpCentral is set to 'true'. Note that the value of 'true' will be effective only if the WLAN is configured as Locally Switched.
1.3.6.1.4.1.9.9.517.1.3.8.1.3TruthValueread-writecurrent
cLReapGroupDhcpRowStatus
OBJECT-TYPE
This object represents the status column for a conceptual row in this table.
1.3.6.1.4.1.9.9.517.1.3.8.1.4RowStatusread-createcurrent
cLReapGroupVlanIdTable
OBJECT-TYPE
This table defines the WLAN / VLAN Id mappings to be configured for the REAP identified by REAP group name. VLAN Id configured through this table is passed to the respective REAP group identified by the REAP group name.
1.3.6.1.4.1.9.9.517.1.3.9not-accessiblecurrent
cLReapGroupVlanIdEntry
OBJECT-TYPE
Each entry represents a conceptual row that corresponds to one WLAN / VLAN Id mapping to be applied to the REAP identified by cLReapGroupName.
1.3.6.1.4.1.9.9.517.1.3.9.1not-accessiblecurrent
cLReapGroupWlanVlanId
OBJECT-TYPE
This object represents the VLAN ID to be mapped to the WLAN identified by cLWlanIndex.
1.3.6.1.4.1.9.9.517.1.3.9.1.1Unsigned32 (1..4095)read-createcurrent
cLReapGroupVlanRowStatus
OBJECT-TYPE
This object represents the reap group vlan mapping row status.
1.3.6.1.4.1.9.9.517.1.3.9.1.2RowStatusread-createcurrent
ciscoLwappReapAclConfig
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.517.1.4
cLReapAclTable
OBJECT-TYPE
The table listing hreap ACLs (Access Control Lists) on the Switch.
1.3.6.1.4.1.9.9.517.1.4.1not-accessiblecurrent
cLReapAclEntry
OBJECT-TYPE
Each entry represents the attributes for clReapAclTable. An entry gets added to the table on creating a flexconnect ACL.
1.3.6.1.4.1.9.9.517.1.4.1.1not-accessiblecurrent
cLReapAclName
OBJECT-TYPE
This object specifies name of the Access Control List.
1.3.6.1.4.1.9.9.517.1.4.1.1.1OCTET STRING (SIZE(1..32))read-createcurrent
cLReapAclApplyMode
OBJECT-TYPE
This object specifies the apply mode of the ACL on the switch. Mode value 'applied' means the ACL has been applied on the switch.
1.3.6.1.4.1.9.9.517.1.4.1.1.2INTEGER {notapplied(0), applied(1)}read-onlycurrent
cLReapAclRowStatus
OBJECT-TYPE
This object specifies the row Status of the ACL.
1.3.6.1.4.1.9.9.517.1.4.1.1.3RowStatusread-createcurrent
cLReapAclRuleTable
OBJECT-TYPE
The table listing Acl Rules(Access Control List Entries) on the ACL with name cLReapAclName.
1.3.6.1.4.1.9.9.517.1.4.2not-accessiblecurrent
cLReapAclRuleEntry
OBJECT-TYPE
Each entry represents the attributes for clReapAclRuleTable. An entry gets added to the table on creating a rule on flexconnect ACL.
1.3.6.1.4.1.9.9.517.1.4.2.1not-accessiblecurrent
cLReapAclRuleIndex
OBJECT-TYPE
Index of the ACL rule. This can be updated to reset the sequence of the rules of an ACL.
1.3.6.1.4.1.9.9.517.1.4.2.1.1Unsigned32 (1..64)read-createcurrent
cLReapAclRuleAction
OBJECT-TYPE
The permission mode of a rule.
1.3.6.1.4.1.9.9.517.1.4.2.1.2INTEGER {deny(0), permit(1)}read-createcurrent
cLReapAclRuleSourceIpAddressType
OBJECT-TYPE
Source IP Address Type of the ACL rule. The value is limited to ipv4 only.
1.3.6.1.4.1.9.9.517.1.4.2.1.3InetAddressTyperead-createcurrent
cLReapAclRuleSourceIpAddress
OBJECT-TYPE
Source IP Address of the ACL rule. es any source address.
1.3.6.1.4.1.9.9.517.1.4.2.1.4InetAddressread-createcurrent
cLReapAclRuleSourceIpNetmaskType
OBJECT-TYPE
Source IP Netmask type of the ACL rule. The value is limited to ipv4 only.
1.3.6.1.4.1.9.9.517.1.4.2.1.5InetAddressTyperead-createcurrent
cLReapAclRuleSourceIpNetmask
OBJECT-TYPE
Source IP Netmask of the ACL rule. A value 0 implies any source mask.
1.3.6.1.4.1.9.9.517.1.4.2.1.6InetAddressread-createcurrent
cLReapAclRuleDestinationIpAddressType
OBJECT-TYPE
Destination IP Address type of the ACL rule. The value is limited to ipv4 only.
1.3.6.1.4.1.9.9.517.1.4.2.1.7InetAddressTyperead-createcurrent
cLReapAclRuleDestinationIpAddress
OBJECT-TYPE
Destination IP Address of the ACL rule. A value 0 implies any destination address.
1.3.6.1.4.1.9.9.517.1.4.2.1.8InetAddressread-createcurrent
cLReapAclRuleDestinationIpNetmaskType
OBJECT-TYPE
Destination Netmask type of the ACL rule. The value is limited to ipv4 only.
1.3.6.1.4.1.9.9.517.1.4.2.1.9InetAddressTyperead-createcurrent
cLReapAclRuleDestinationIpNetmask
OBJECT-TYPE
Destination Netmask of the ACL rule. A value 0 implies any destination mask.
1.3.6.1.4.1.9.9.517.1.4.2.1.10InetAddressread-createcurrent
cLReapAclRuleProtocol
OBJECT-TYPE
Protocol of the packet. It can be either of the pre specified protocols like TCP, UDP, ICMP, ESP, AH, GRE, IP, Ethernet Over IP, OSPF or any number between 0 and 255. A value 256 implies that this rule applies to 'Any' protocol.
1.3.6.1.4.1.9.9.517.1.4.2.1.11Unsigned32 (0..256)read-createcurrent
cLReapAclRuleStartSourcePort
OBJECT-TYPE
Source Port of the packet. It can be either of the pre specified ports like HTTP, HTTPS, Telnet, RADIUS etc or any number between 0 and 65535. A value 65536 implies that this rule applies to 'Any' source port. This value can be set only if the protocol is set to TCP or UDP. Otherwise the value is set to Any(65536)
1.3.6.1.4.1.9.9.517.1.4.2.1.12Unsigned32 (0..65536)read-createcurrent
cLReapAclRuleEndSourcePort
OBJECT-TYPE
Source Port of the packet. It can be either of the pre specified ports like HTTP, HTTPS, Telnet, RADIUS etc or any number between 0 and 65535. A value 65536 implies that this rule applies to 'Any' source port. This value can be set only if the protocol is set to TCP or UDP. Otherwise the value is set to Any(65536)
1.3.6.1.4.1.9.9.517.1.4.2.1.13Unsigned32 (0..65536)read-createcurrent
cLReapAclRuleStartDestinationPort
OBJECT-TYPE
Destination Port of the packet. It can be either of the pre specified ports like HTTP, HTTPS, Telnet, RADIUS etc or any number between 0 and 65535. A value 65536 implies that this rule aplpies to 'Any' Destination port. This value can be set only if the protocol is set to TCP or UDP. Otherwise the value is set to Any(65536)
1.3.6.1.4.1.9.9.517.1.4.2.1.14Unsigned32 (0..65536)read-createcurrent
cLReapAclRuleEndDestinationPort
OBJECT-TYPE
Destination Port of the packet. It can be either of the pre specified ports like HTTP, HTTPS, Telnet, RADIUS etc or any number between 0 and 65535. A value 65536 implies that this rule aplpies to 'Any' Destination port. This value can be set only if the protocol is set to TCP or UDP. Otherwise the value is set to Any(65536)
1.3.6.1.4.1.9.9.517.1.4.2.1.15Unsigned32 (0..65536)read-createcurrent
cLReapAclRuleDscp
OBJECT-TYPE
DSCP value of the rule. A value 256 implies Any
1.3.6.1.4.1.9.9.517.1.4.2.1.16Unsigned32 (0..256)read-createcurrent
cLReapAclNewRuleIndex
OBJECT-TYPE
New Index of the ACL rule. This attribute should be updated if the requirement is to reset the sequence of the rules of an ACL. A read on this will not yield anything.
1.3.6.1.4.1.9.9.517.1.4.2.1.17Unsigned32 (1..64)read-createcurrent
cLReapAclRuleRowStatus
OBJECT-TYPE
Row Status of the ACL Rule.
1.3.6.1.4.1.9.9.517.1.4.2.1.18RowStatusread-createcurrent
cLReapL2AclTable
OBJECT-TYPE
The table listing Layer2 ACLs (Access Control Lists) on the Switch.
1.3.6.1.4.1.9.9.517.1.4.3not-accessiblecurrent
cLReapL2AclEntry
OBJECT-TYPE
Each entry represents the attributes for cLReapL2AclTable. An entry gets added to the table on creating a Layer2 ACL.
1.3.6.1.4.1.9.9.517.1.4.3.1not-accessiblecurrent
cLReapL2AclName
OBJECT-TYPE
This object specifies name of the L2 Access Control List.
1.3.6.1.4.1.9.9.517.1.4.3.1.1OCTET STRING (SIZE(1..32))not-accessiblecurrent
cLReapL2AclApplyMode
OBJECT-TYPE
This object specifies the apply mode of the L2ACL on the switch. Mode value 'applied' means the L2ACL has been applied on the switch. Default mode on creation on ACL will be notapplied.
1.3.6.1.4.1.9.9.517.1.4.3.1.2INTEGER {notapplied(1), applied(2)}read-onlycurrent
cLReapL2AclRowStatus
OBJECT-TYPE
This object specifies the row Status of the L2ACL.
1.3.6.1.4.1.9.9.517.1.4.3.1.3RowStatusread-createcurrent
cLReapL2AclRuleTable
OBJECT-TYPE
The table listing L2Acl Rules(Access Control List Entries) on the L2ACL with name cLReapL2AclName.
1.3.6.1.4.1.9.9.517.1.4.4not-accessiblecurrent
cLReapL2AclRuleEntry
OBJECT-TYPE
Each entry represents the attributes for clReapL2AclRuleTable. An entry gets added to the table on creating a rule on L2ACL.
1.3.6.1.4.1.9.9.517.1.4.4.1not-accessiblecurrent
cLReapL2AclRuleIndex
OBJECT-TYPE
This object represents the unique index of the L2ACL rule. This can be updated to reset the sequence of the rules of an L2ACL.
1.3.6.1.4.1.9.9.517.1.4.4.1.1Unsigned32not-accessiblecurrent
cLReapL2AclRuleAction
OBJECT-TYPE
This object specifies the permission mode of a rule.
1.3.6.1.4.1.9.9.517.1.4.4.1.2INTEGER {deny(1), permit(2)}read-createcurrent
cLReapL2AclRuleEthertype
OBJECT-TYPE
This object represents the etherType of the L2Acl rule. Default is 0x0
1.3.6.1.4.1.9.9.517.1.4.4.1.3Unsigned32 (0..65536)read-createcurrent
cLReapL2AclRuleEthertypeMask
OBJECT-TYPE
This object represents the etherType Mask of the L2Acl rule. Default is 0x0
1.3.6.1.4.1.9.9.517.1.4.4.1.4Unsigned32 (0..65536)read-createcurrent
cLReapL2AclRuleDirection
OBJECT-TYPE
This object specifies the direction of the packet to which the rule may be applied.
1.3.6.1.4.1.9.9.517.1.4.4.1.5INTEGER {inbound(1), outbound(2), any(3)}read-createcurrent
cLReapL2AclNewRuleIndex
OBJECT-TYPE
This object specifies the new Index of the L2ACL rule. This attribute should be updated if the requirement is to reset the sequence of the rules of an ACL. A read on this will yield the same value as cLReapL2AclRuleIndex.
1.3.6.1.4.1.9.9.517.1.4.4.1.6Unsigned32 (1..64)read-createcurrent
cLReapL2AclRuleRowStatus
OBJECT-TYPE
This object specifies the status of a conceptual row in the ACL Rule Table. This is used to create and delete entries in the table.
1.3.6.1.4.1.9.9.517.1.4.4.1.7RowStatusread-createcurrent
ciscoLwappReapMasterApConfig
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.517.1.5
cLReapMasterApConfigTable
OBJECT-TYPE
This table represents the master AP admin configuration of REAPs. The agent adds a row to this table corresponding to each row representing a REAP in cLApTable of the CISCO-LWAPP-AP-MIB. The agent deletes the row either when the AP dissociates from the controller or moved out of the remote mode.
1.3.6.1.4.1.9.9.517.1.5.1not-accessiblecurrent
cLReapMasterApConfigEntry
OBJECT-TYPE
Each entry represents a conceptual row in cLReapMasterApConfigTable and corresponds to the Master configuration of a REAP.
1.3.6.1.4.1.9.9.517.1.5.1.1not-accessiblecurrent
cLReapMasterApModel
OBJECT-TYPE
The object specifies the model of the AP in the hreap group.
1.3.6.1.4.1.9.9.517.1.5.1.1.1DisplayStringread-onlycurrent
cLReapMasterApManual
OBJECT-TYPE
This object represents if this REAP AP is manually configured by the user. A value of 'true' indicates that this REAP master is manually configured. A value of 'false' indicates that this REAP master is not manually configured.
1.3.6.1.4.1.9.9.517.1.5.1.1.2TruthValueread-onlycurrent
cLReapMasterApRowStatus
OBJECT-TYPE
This object specifies the row Status of the Master table.
1.3.6.1.4.1.9.9.517.1.5.1.1.3RowStatusread-createcurrent
ciscoLwappReapGlobalConfig
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.517.1.6
cLReapArpCaheEnabled
OBJECT-TYPE
This object specifies whether ARP cache feature is enabled for the flexconnect Access Points connected to the Wireless LAN Controller.
1.3.6.1.4.1.9.9.517.1.6.1TruthValueread-writecurrent
ciscoLwappReapMIBConform
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.517.2
ciscoLwappReapMIBCompliances
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.517.2.1
ciscoLwappReapMIBGroups
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.517.2.2

Conformance

NameOIDStatus
ciscoLwappReapMIBCompliance
MODULE-COMPLIANCE
The compliance statement for the SNMP entities that implement the ciscoLwappReapMIB module.
1.3.6.1.4.1.9.9.517.2.1.1deprecated
ciscoLwappReapMIBComplianceRev1
MODULE-COMPLIANCE
The compliance statement for the SNMP entities that implement the ciscoLwappReapMIB module.
1.3.6.1.4.1.9.9.517.2.1.2deprecated
ciscoLwappReapMIBComplianceRev2
MODULE-COMPLIANCE
The compliance statement for the SNMP entities that implement the ciscoLwappReapMIB module.
1.3.6.1.4.1.9.9.517.2.1.3deprecated
ciscoLwappReapMIBComplianceRev3
MODULE-COMPLIANCE
The compliance statement for the SNMP entities that implement the ciscoLwappReapMIB module.
1.3.6.1.4.1.9.9.517.2.1.4deprecated
ciscoLwappReapMIBComplianceRev4
MODULE-COMPLIANCE
The compliance statement for the SNMP entities that implement the ciscoLwappReapMIB module.
1.3.6.1.4.1.9.9.517.2.1.5deprecated
ciscoLwappReapMIBComplianceRev5
MODULE-COMPLIANCE
The compliance statement for the SNMP entities that implement the ciscoLwappReapMIB module.
1.3.6.1.4.1.9.9.517.2.1.6current
ciscoLwappReapWlanConfigGroup
OBJECT-GROUP
This collection of objects represent the WLAN configuration to be passed to the REAP.
1.3.6.1.4.1.9.9.517.2.2.1current
ciscoLwappReapApConfigGroup
OBJECT-GROUP
This collection of objects represent the information needed by the REAP AP to locally switch the client data packets. The collection also includes the VLAN configuration on the REAP.
1.3.6.1.4.1.9.9.517.2.2.2current
ciscoLwappReapGroupConfigGroup
OBJECT-GROUP
This collection of objects represent the information needed by the REAP APs to configure REAP groups.
1.3.6.1.4.1.9.9.517.2.2.3current
ciscoLwappReapGroupConfigRadiusGroup
OBJECT-GROUP
This collection of objects represent the RADIUS information needed by the REAP APs in a REAP group.
1.3.6.1.4.1.9.9.517.2.2.4deprecated
ciscoLwappReapGroupConfigUserAuthGroup
OBJECT-GROUP
This collection of objects represent the information needed for user authentication.
1.3.6.1.4.1.9.9.517.2.2.5current
ciscoLwappReapApConfigGroupHomeAp
OBJECT-GROUP
This supplemental collection of objects represents objects related to Home AP configuration for REAP AP.
1.3.6.1.4.1.9.9.517.2.2.6current
ciscoLwappReapGroupConfigRadiusGroup1
OBJECT-GROUP
This collection of objects represent the RADIUS information needed by the REAP APs in a REAP group.
1.3.6.1.4.1.9.9.517.2.2.7current
ciscoLwappReapWlanConfigGroupSup1
OBJECT-GROUP
This collection of objects represent additional WLAN configuration to be passed to the REAP.
1.3.6.1.4.1.9.9.517.2.2.8current