CISCO-CATOS-ACL-QOS-MIB
- Registered at
- 1.3.6.1.4.1.9.9.179
- Last updated
- 2007-11-02 00:00
- Organization
- Cisco Systems Inc.
- Revisions
- 2007-11-02 00:00, 2006-07-15 00:00, 2005-07-26 00:00, 2004-05-26 00:00, 2003-11-26 00:00, 2003-10-28 00:00, 2003-09-30 00:00, 2003-07-01 00:00, 2003-03-05 00:00, 2002-10-10 00:00, 2002-01-17 00:00, 2001-10-18 00:00, 2001-02-15 00:00, 2001-02-07 00:00
- Namespace
- cisco
- Source file
CISCO-CATOS-ACL-QOS-MIB- Digest
sha256:377eff129260f9656657b2eedf17e8b6512b30639c352a58f5f13f9fc6095658
Description
This MIB module is for Access Control Lists(ACLs) configuration of Quality of Service (QoS) as well as Security feature on the Cisco Catalyst 5000/6000 series switch running CatOS. It also provides QoS configuration and statistics information. Configuration information available through this MIB includes Security and QoS ACL configuration for IP, IPX and Layer 2 traffic, QoS and Security configuration parameters. Statistics available through this MIB includes QoS statistics for Layer 3 traffic. In addition, detailed, flow-specific statistics are also available. This MIB module is applied in conjunction with CISCO-QOS-POLICY-CONFIG-MIB. The configuration information available through this MIB takes effect throughout the device when the value of qosPrOperPolicySource object in CISCO-QOS-POLICY-CONFIG-MIB is 'local' or applies to a specific interface when the value of qosPrIfOperPolicySource object in CISCO-QOS-POLICY-CONFIG-MIB which associates with that interface is 'local' while the value of qosPrOperPolicySource is not 'local'. The following terms are used throughout this MIB: ACE stands for Access Control Entry. An ACL consists of an ordered set of ACEs. ACE is a filter which is used to identify flows with certain characteristics. It includes fields such as ingress/egress ports, L2(layer 2) addresses, L3(layer 3) addresses, TCP/UDP port numbers, etc. QoS ACE and Security ACE are very similar to each other but the actions of the ACEs are different. Security ACEs are compared to each packet, and each ACE specifies whether packets that match with it are either forwarded or dropped. ESP: Enscrypted Security Payload. QoS is the method which attempts to ensure that the network requirements of different applications can be met by giving preferential forwarding treatment to some traffic. It is usually consisted of these steps: classification, policing, output scheduling, marking and shaping. Classification identifies the traffic. Policing checks if the traffic conformed to a specified criteria. Output scheduling, marking and shaping control how the traffic is transmitted to the next hop. A flow is a non-specific term for a microflow or an aggregate flow. Microflow is a single instance of an application to application flow of packets which is identified by source address, source port, destination address, destination port and protocol id. Aggregate flow is a collection of microflows that are treated together as one for the purpose of QoS. DSCP (Differentiated Services Code Point) is the six most significant bits of the ToS field in a IP packet header. DSCP Mutation: the previous hop(s) and the following hop(s) of a device may reside in a different QoS domain. A QoS domain refers to the set of QoS rules and conventions adopted by an administrative entity. For instance, a set of DSCP values may have a different meaning in different domains. DSCP mutation allows a DSCP set to be mutated or transformed in order to maintain semantic compatibility between adjacent domains. The mutation is done via mapping tables which maps the old DSCP value from one domain to a new DSCP value in the other domain. IP precedence is the three most significant bits of the ToS field in a IP packet header. Cos (Class of Service) is the three bits in the layer 2 header that indicates user priority value assigned to this packet. Trust state is a parameter configured at a physical interface or an ACL to determine a DSCP value assigned to a packet for QoS purpose. In profile packet is a packet that does not cause the committed access rate of the packet's flow to be exceeded. Out of profile packet is a packet that cause the committed access rate of the packet's flow to be exceeded. To accomplish classification, the user defines an ACL describing the specification of a traffic flow then attaches this ACL to a physical interface or a vlan. When a packet arrives at an interface, depending on the configured trust state at that interface, it can either be matched against an ACL if the trust state is not trusted or get a DSCP assigned and go directly to output scheduling. In the former case, when the packet matches an ACE in the attached ACL, the next step will be policing. At the end of classification process, a packet has a DSCP value assigned. In some platform (e.g. Catalyst 4000) that does not support ACL configuration, classification is accomplished by matching the Cos value of incoming packet. A packet can be policed at microflow or aggregate flow level. Policing is done using the token bucket algorithm. At the end of policing process, if packet does not cause the flow to exceed the normal rate, it will continue to the next step. Otherwise, the packet is dropped or assigned a 'policed' DSCP value. Some platforms support multi-rate policing. When packet causes the flow to exceed the normal rate but not the excess rate, it is assigned a 'policed' DSCP value. When packet causes the flow to exceed excess rate, it is either dropped or has a 'policed' DSCP value assigned. After policing process, the next step is output scheduling. Output scheduling is the process of assigning a packet to a queue and a threshold according to the packet's Cos value. To get its Cos value, a DSCP to Cos mapping will be performed. This MIB also defines 'Security ACLs' which some devices support as a mean to enforce security. Security ACLs, attached at an ingress interface, are compared to each packet arriving at that interface. If the packet matches an ACE in the ACLs, it is either permitted to go through the device or blocked and dropped or redirected to another interface.
Contact
Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-wbu@cisco.com
Imports
| From | Symbols |
|---|---|
| CISCO-QOS-PIB-MIB | Dscp, Percent, QosInterfaceQueueType, QosLayer2Cos |
| CISCO-SMI | ciscoMgmt |
| CISCO-SWITCH-ENGINE-MIB | cseFlowDataEntry |
| CISCO-TC | CiscoIpProtocol, CiscoPortList |
| CISCO-VTP-MIB | VlanIndex |
| HCNUM-TC | CounterBasedGauge64 |
| IF-MIB | InterfaceIndex, ifIndex |
| INET-ADDRESS-MIB | InetAddress, InetAddressType, InetPortNumber |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP |
| SNMPv2-SMI | Counter32, Counter64, Gauge32, Integer32, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, Unsigned32, iso |
| SNMPv2-TC | DateAndTime, DisplayString, MacAddress, RowStatus, TEXTUAL-CONVENTION, TruthValue |
Imported by
Nothing in this corpus imports this module.
Load order
Every file a consumer needs in order to load this module, dependencies first.
CISCO-CATOS-ACL-QOS-MIB CISCO-QOS-PIB-MIB CISCO-SMI CISCO-SWITCH-ENGINE-MIB CISCO-TC CISCO-VTP-MIB ENTITY-MIB HCNUM-TC IANA-ENTITY-MIB IANAifType-MIB IF-MIB INET-ADDRESS-MIB MPLS-VPN-MIB RMON-MIB SNMP-FRAMEWORK-MIB SNMPv2-CONF SNMPv2-MIB SNMPv2-SMI SNMPv2-TC UUID-TC-MIB
Textual conventions
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| CaqAclName TEXTUAL-CONVENTION A character string for an ACL (Access Control List) name. Valid characters are a-z, A-Z, 0-9, '-', '_' and '.'. Some devices may require that an AclName contains at least one non-numeric character. Acl name is case sensitive. | current | |||
| CaqAdjacencyName TEXTUAL-CONVENTION A character string for an adjacency name. Valid characters are a-z, A-Z, 0-9, '-', '_' and '.'. Some devices may require that an AdjacencyName contains at least one non-numeric character. Adjacency name is case sensitive. | current | |||
| CaqDirection TEXTUAL-CONVENTION Indicates a particular direction of traffic. | current | |||
| CaqHitCountAclType TEXTUAL-CONVENTION An integer indicating the ACL type that supports ACL hit count feature. | current | |||
| CaqIpPrecedence TEXTUAL-CONVENTION Indicates the IP precedence. | current | |||
| CaqPolicerName TEXTUAL-CONVENTION A character string for a policer name. Valid characters are a-z, A-Z, 0-9, '-', '_' and '.'. Some devices may require that a PolicerName contains at least one non-numeric character. Policer name is case sensitive. | current | |||
| CaqPolicerNameOrEmpty TEXTUAL-CONVENTION This textual convention is an extension of the PolicerName convention. The latter defines a non-empty policer name. This extension permits the additional value of empty string. Examples of the usage of empty string might include situations where there is no policer defined for an ACE. | current | |||
| CaqQueueNumber TEXTUAL-CONVENTION An integer indicates a queue number. | current | |||
| CaqThresholdNumber TEXTUAL-CONVENTION An integer indicates a threshold number. | current |
Objects
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| ciscoCatOSAclQosMIBObjects OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.179.1 | |||
| caqGlobalObjects OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.179.1.1 | |||
| caqCosToDscpTable OBJECT-TYPE This table contains the mapping of Cos values to DSCP values. This map is used to associate the Cos of packets arriving at a port to a DSCP where the port's trust state is trustCoS(2). This map is a table of eight Cos values (0 through 7) and their corresponding DSCP values. This mapping applies to every port on the device. | 1.3.6.1.4.1.9.9.179.1.1.1 | not-accessible | current | |
| caqCosToDscpEntry OBJECT-TYPE Each row contains the mapping from a CoS value to a DSCP value. | 1.3.6.1.4.1.9.9.179.1.1.1.1 | not-accessible | current | |
| caqCosToDscpCos OBJECT-TYPE The CoS value being mapped to the DSCP value in this device. | 1.3.6.1.4.1.9.9.179.1.1.1.1.1 | QosLayer2Cos | not-accessible | current |
| caqCosToDscpDscp OBJECT-TYPE The DSCP value which the CoS value maps to. The default configuration is : CoS DSCP 0 0 1 8 2 16 3 24 4 32 5 40 6 48 7 56 . | 1.3.6.1.4.1.9.9.179.1.1.1.1.2 | Dscp | read-write | current |
| caqIpPrecToDscpTable OBJECT-TYPE This table contains the mapping of IP Precedence to DSCP. This map is used to associate the IP Precedence of IP packets arriving at a port to a DSCP where the port's trust state is trustIpPrec(3). This map is a table of eight IpPrecedence values (0 through 7) and their corresponding DSCP values. This mapping applies to every port on the device. | 1.3.6.1.4.1.9.9.179.1.1.2 | not-accessible | current | |
| caqIpPrecToDscpEntry OBJECT-TYPE Each row contains the mapping from an IP Precedence value to a DSCP value. | 1.3.6.1.4.1.9.9.179.1.1.2.1 | not-accessible | current | |
| caqIpPrecToDscpIpPrec OBJECT-TYPE The IP Precedence value being mapped to the DSCP value in this device. | 1.3.6.1.4.1.9.9.179.1.1.2.1.1 | CaqIpPrecedence | not-accessible | current |
| caqIpPrecToDscpDscp OBJECT-TYPE The DSCP value which the IP Precedence value maps to. The default configuration is the identity function : IPPrec DSCP 0 0 1 8 2 16 3 24 4 32 5 40 6 48 7 56 . | 1.3.6.1.4.1.9.9.179.1.1.2.1.2 | Dscp | read-write | current |
| caqDscpMappingTable OBJECT-TYPE This table always has 64 entries, one for each DSCP value. The table contains three mappings from the DSCP value assigned to a packet. One mapping is to the egress CoS to be stored in the layer-2 frame headers for output on 802.1Q or ISL interfaces. The other two mappings are to the remarked (or 'marked down') DSCP values which are used when a policer's requires that a packet's DSCP value to be modified. Of these two mappings, one is for a Normal Rate policer, and the other is for an Excess Rate policer. These mappings apply for every port on the device. | 1.3.6.1.4.1.9.9.179.1.1.3 | not-accessible | current | |
| caqDscpMappingEntry OBJECT-TYPE Each row contains the mapping from DSCP value to CoS value and policed DSCP. | 1.3.6.1.4.1.9.9.179.1.1.3.1 | not-accessible | current | |
| caqDscpMappingDscp OBJECT-TYPE The DSCP value being mapped to the CoS value and policed DSCP value in this device. | 1.3.6.1.4.1.9.9.179.1.1.3.1.1 | Dscp | not-accessible | current |
| caqDscpMappingCos OBJECT-TYPE The CoS value which the DSCP values maps to. The default configuration is calculated from the formula CoS = DSCP divide by 8. That is: DSCP 0-7 all map to CoS 0; DSCP 8-15 all map to CoS 1; ... DSCP 32-39 all map to CoS 4; ... DSCP 56-63 all map to CoS 7. | 1.3.6.1.4.1.9.9.179.1.1.3.1.2 | QosLayer2Cos | read-write | current |
| caqDscpMappingNRPolicedDscp OBJECT-TYPE The normal rate policed DSCP value which the DSCP values maps to. The normal rate default mapping of DSCP to 'marked down' DSCP is the identity function. That is: 63 -> 63 62 -> 62 ... 31 -> 31 ... 2 -> 2 1 -> 1 0 -> 0. | 1.3.6.1.4.1.9.9.179.1.1.3.1.3 | Dscp | read-write | current |
| caqDscpMappingERPolicedDscp OBJECT-TYPE The excess rate policed DSCP value which the DSCP values maps to. If the value of caqFlowPolicerExcessRateSupport object is false(2), this object cannot be instantiated. The excess rate default DSCP mapping of DSCP to 'marked down' DSCP is the identity function. That is: 63 -> 63 62 -> 62 ... 31 -> 31 ... 2 -> 2 1 -> 1 0 -> 0. | 1.3.6.1.4.1.9.9.179.1.1.3.1.4 | Dscp | read-write | current |
| caqCosAssignmentTable OBJECT-TYPE This table provides the information for and configuration of assigning packets to queues and thresholds based on their CoS value. | 1.3.6.1.4.1.9.9.179.1.1.4 | not-accessible | current | |
| caqCosAssignmentEntry OBJECT-TYPE The assignment of packets to a pair of queue and threshold based on their Cos value. The packets assignment also depends on port types. For each port type, there is a set of Cos value (0..7) associated with a pair of queue number and threshold number (q,t). Packets that have their Cos value belong to a particular set will be assigned to the pair of queue number and threshold number that this set associated with. | 1.3.6.1.4.1.9.9.179.1.1.4.1 | not-accessible | current | |
| caqCosAssignQueueType OBJECT-TYPE The queue type of this interface. | 1.3.6.1.4.1.9.9.179.1.1.4.1.1 | QosInterfaceQueueType | not-accessible | current |
| caqCosAssignCos OBJECT-TYPE Indicates the Cos value which is used to match the Cos value of packets for queue assignment. | 1.3.6.1.4.1.9.9.179.1.1.4.1.2 | QosLayer2Cos | not-accessible | current |
| caqCosAssignQueueNumber OBJECT-TYPE The queue number which the Cos value denoted by caqCosAssignCos will be associated with. This queue number must not larger than the queue count defined by caqCosAssignQueueType. | 1.3.6.1.4.1.9.9.179.1.1.4.1.3 | CaqQueueNumber | read-write | current |
| caqCosAssignThresholdNumber OBJECT-TYPE The threshold number which the Cos value denoted by caqCosAssignCos will be associated with. This threshold number must not larger than the threshold count defined by caqCosAssignQueueType. | 1.3.6.1.4.1.9.9.179.1.1.4.1.4 | CaqThresholdNumber | read-write | current |
| caqQueueThresholdTable OBJECT-TYPE This table maintains threshold parameters for the specified queue number and threshold number of a port type. | 1.3.6.1.4.1.9.9.179.1.1.5 | not-accessible | current | |
| caqQueueThresholdEntry OBJECT-TYPE For each threshold of a queue, there are parameters to set on the threshold. This entry contains the parameters. | 1.3.6.1.4.1.9.9.179.1.1.5.1 | not-accessible | current | |
| caqQueueThreshQueueType OBJECT-TYPE Indicates the queue type. | 1.3.6.1.4.1.9.9.179.1.1.5.1.1 | QosInterfaceQueueType | not-accessible | current |
| caqQueueThreshQueueIndex OBJECT-TYPE Indicates queue number. This queue number must not be larger than the queue count defined by caqQueueThreshQueueType. | 1.3.6.1.4.1.9.9.179.1.1.5.1.2 | CaqQueueNumber | not-accessible | current |
| caqQueueThreshThresholdIndex OBJECT-TYPE Indicates threshold number. This threshold number must not be larger than the threshold count defined by caqQueueThreshQueueType. | 1.3.6.1.4.1.9.9.179.1.1.5.1.3 | CaqThresholdNumber | not-accessible | current |
| caqQueueThreshDropAlgorithm OBJECT-TYPE Indicates the drop algorithm used at this queue and threshold. tailDrop(1) indicates that tailDrop is used. wred(2) indicates that WRED is used. | 1.3.6.1.4.1.9.9.179.1.1.5.1.4 | INTEGER {tailDrop(1), wred(2)} | read-only | current |
| caqQueueThreshDropThreshold OBJECT-TYPE This object specifies the drop threshold parameter for a pair of queue and threshold of an interface queue type when the drop algorithm is tail drop. Once the packets in the buffer is more than the value of this object, the incoming packets of the buffer are dropped. The value is a percentage of the full buffer. This object is instantiated only if the value of caqQueueThreshDropAlgorithm is tailDrop(1). | 1.3.6.1.4.1.9.9.179.1.1.5.1.5 | Unsigned32 (1..100) | read-write | current |
| caqQueueThreshMinWredThreshold OBJECT-TYPE This object specifies the min WRED threshold parameter of a threshold number for the specific port type when WRED drop algorithm is used. WRED (Weighted Random Early Detect) is a mechanism which drops packets fairly during congestion so that adaptive applications can react to congestion. This object specifies a percentage of the buffer size. This object is instantiated only if the value of caqQueueThreshDropAlgorithm is wred(2). | 1.3.6.1.4.1.9.9.179.1.1.5.1.6 | Percent | read-write | current |
| caqQueueThreshMaxWredThreshold OBJECT-TYPE This object specifies the max WRED threshold parameter of a threshold number for the specific port type when WRED drop algorithm is used. This object is instantiated only if the value of caqQueueThreshDropAlgorithm is wred(2). | 1.3.6.1.4.1.9.9.179.1.1.5.1.7 | Unsigned32 (1..100) | read-write | current |
| caqQueueTable OBJECT-TYPE A table used to configure the WRR (weighted round robin) weights for queues and the ratio of memory buffer allocation for each queue. It only contains entries for the specific port types which supports either WRR or buffer allocation. | 1.3.6.1.4.1.9.9.179.1.1.6 | not-accessible | current | |
| caqQueueEntry OBJECT-TYPE A set of WRR weight and memory buffer allocation ratio for ingress or egress of a specific queue. | 1.3.6.1.4.1.9.9.179.1.1.6.1 | not-accessible | current | |
| caqQueueDirection OBJECT-TYPE Indicates whether this row's queue parameters are to be applied for ingress or for egress traffic. | 1.3.6.1.4.1.9.9.179.1.1.6.1.1 | CaqDirection | not-accessible | current |
| caqQueueType OBJECT-TYPE Indicates the queue type. | 1.3.6.1.4.1.9.9.179.1.1.6.1.2 | QosInterfaceQueueType | not-accessible | current |
| caqQueueNumber OBJECT-TYPE Indicates queue number. | 1.3.6.1.4.1.9.9.179.1.1.6.1.3 | CaqQueueNumber | not-accessible | current |
| caqQueueWrrWeight OBJECT-TYPE This object is to configure the weight for the specified queue type and for the specified direction. | 1.3.6.1.4.1.9.9.179.1.1.6.1.4 | Unsigned32 (1..255) | read-write | current |
| caqQueueBufferSizeRatio OBJECT-TYPE Indicates the percentage of ingress or egress packet buffer memory allocated to the specified queue. | 1.3.6.1.4.1.9.9.179.1.1.6.1.5 | Unsigned32 (1..99) | read-write | current |
| caqDscpMutationMapTable OBJECT-TYPE The table provides the DSCP mutation mapping configuration on the device. This table is only instantiated if DSCP Mutation is supported by the device. | 1.3.6.1.4.1.9.9.179.1.1.7 | not-accessible | current | |
| caqDscpMutationMapEntry OBJECT-TYPE Each row contains the mapping from old DSCP value to new DSCP value per specific mutation table. | 1.3.6.1.4.1.9.9.179.1.1.7.1 | not-accessible | current | |
| caqDscpMutationTableId OBJECT-TYPE The mutation table ID number. | 1.3.6.1.4.1.9.9.179.1.1.7.1.1 | Unsigned32 | not-accessible | current |
| caqDscpMutationOldDscp OBJECT-TYPE The old DSCP value. | 1.3.6.1.4.1.9.9.179.1.1.7.1.2 | Dscp | not-accessible | current |
| caqDscpMutationNewDscp OBJECT-TYPE The new DSCP value which the old DSCP values maps to for a specific mutation table. The default mapping of old DSCP to new DSCP for mutation purpose is the identity function. That is: 63 -> 63 62 -> 62 ... 31 -> 31 ... 2 -> 2 1 -> 1 0 -> 0. | 1.3.6.1.4.1.9.9.179.1.1.7.1.3 | Dscp | read-write | current |
| caqVlanMutationIdMapTable OBJECT-TYPE The table provides the VLAN to mutation table mapping configuration on the device. This table is only instantiated if DSCP Mutation is supported by the device. | 1.3.6.1.4.1.9.9.179.1.1.8 | not-accessible | current | |
| caqVlanMutationIdMapEntry OBJECT-TYPE When the first time a VLAN is created in a device supporting this table, a corresponding entry of this table will be added. The value of caqVlanMutationTableId object in such row will be initialized to 0. | 1.3.6.1.4.1.9.9.179.1.1.8.1 | not-accessible | current | |
| caqVlanMutationIndex OBJECT-TYPE Indicates the VLAN number. | 1.3.6.1.4.1.9.9.179.1.1.8.1.1 | VlanIndex | not-accessible | current |
| caqVlanMutationTableId OBJECT-TYPE Indicates the mutation table ID number. The value of this object should match one of caqDscpMutationTableId object value in caqDscpMutationMapTable. Mutation table 0 always provides the identity mapping. | 1.3.6.1.4.1.9.9.179.1.1.8.1.2 | Unsigned32 | read-write | current |
| caqDscpRewriteEnabled OBJECT-TYPE Indicates whether DSCP rewrite is enabled or disabled in the device. if true(1), all outgoing packets will have their DSCP value rewrited based on the result of classification, policing or DSCP mutation configured in the device. if false(2), all outgoing packets will have their DSCP values as when they arrived. | 1.3.6.1.4.1.9.9.179.1.1.9 | TruthValue | read-write | current |
| caqMacPktClassifyVlansLow OBJECT-TYPE A string of octets containing one bit per VLAN for VLANs with VlanIndex value of 0 to 2047. The first octet corresponds to VLANs with VlanIndex values of 0 through 7; the second octet to VLANs 8 through 15; etc. The most significant bit of each octet corresponds to the lowest value VlanIndex in that octet. For each VLAN, if Ethernet packet classify feature is enabled then the bit corresponding to that VLAN is set to '1'. Note that if the length of this string is less than 256 octets, any 'missing' octets are assumed to contain the value zero. A NMS may omit any zero-valued octets from the end of this string in order to reduce SetPDU size, and the agent may also omit zero-valued trailing octets, to reduce the size of GetResponse PDUs. | 1.3.6.1.4.1.9.9.179.1.1.10 | OCTET STRING (SIZE(0..256)) | read-write | current |
| caqMacPktClassifyVlansHigh OBJECT-TYPE A string of octets containing one bit per VLAN for VLANs with VlanIndex value of 2048 to 4095. The first octet corresponds to VLANs with VlanIndex values of 2048 through 2055; the second octet to VLANs 2056 through 2063; etc. The most significant bit of each octet corresponds to the lowest value VlanIndex in that octet. For each VLAN, if Ethernet packet classify feature is enabled then the bit corresponding to that VLAN is set to '1'. Note that if the length of this string is less than 256 octets, any 'missing' octets are assumed to contain the value zero. A NMS may omit any zero-valued octets from the end of this string in order to reduce SetPDU size, and the agent may also omit zero-valued trailing octets, to reduce the size of GetResponse PDUs. | 1.3.6.1.4.1.9.9.179.1.1.11 | OCTET STRING (SIZE(0..256)) | read-write | current |
| caqInterfaceObjects OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.179.1.2 | |||
| caqIfConfigTable OBJECT-TYPE This table describes the trust state and the default Cos value configured at each physical interface. It also indicates whether an ACL attached to a Qos capable physical interface is applied per VLAN or per physical interface if the platform supports ACL configuration. | 1.3.6.1.4.1.9.9.179.1.2.1 | not-accessible | current | |
| caqIfConfigEntry OBJECT-TYPE The index of this table is the ifIndex of a physical port with QoS capability. | 1.3.6.1.4.1.9.9.179.1.2.1.1 | not-accessible | current | |
| caqIfCos OBJECT-TYPE This object indicates the default Cos value configured at this physical interface. This default value will be assigned to packet which does not have a Cos value in its layer-2 header when the packet arrives at this interface. | 1.3.6.1.4.1.9.9.179.1.2.1.1.1 | QosLayer2Cos | read-write | current |
| caqIfTrustStateConfig OBJECT-TYPE This object is used to set the trust state of an interface. (whether the packets arriving at an interface are trusted to carry the correct data for classification.) If the object is untrusted(1), then the DSCP assigned to the packet is the DSCP specified by classification rule obtained from the matching ACE (Access Control Entry). ACE is a filter that is used to identify flows with certain characteristics. It includes fields such as ingress/egress ports, L2 addresses, L3 addresses , TCP/UDP port number. If this object is trustCoS(2), then the DSCP assigned to the packet is the layer2 CoS of the packet mapped to a DSCP by the CoS-to-DSCP mapping defined in object caqCosToDscpDscp. When this object is trustIpPrec(3), a DSCP is assigned to an IP packet according to the IP-Precedence-to-DSCP mapping defined by the values contained in caqIpPrecToDscpTable. For non-IP packets, trustIpPrec(3) has identical behavior as trustCoS(2). When this object is trustDscp(4), the DSCP contained in an IP packet is trusted as being the correct value to assign to it. For non-IP packets, trustDscp(4) has identical behavior as trustCoS(2). | 1.3.6.1.4.1.9.9.179.1.2.1.1.2 | INTEGER {untrusted(1), trustCoS(2), trustIpPrec(3), trustDscp(4)} | read-write | current |
| caqIfAclBase OBJECT-TYPE For a given physical interface, this object indicates whether packets arriving at that interface are classified and policed based on port's ACL or based on the ACL of the VLAN which the port belongs to. This object is only instantiated if the platform support ACL configuration. | 1.3.6.1.4.1.9.9.179.1.2.1.1.3 | INTEGER {vlan(1), port(2)} | read-write | current |
| caqIfTrustDevice OBJECT-TYPE For a given physical interface, this object indicates the restriction on trusting only a specific type of device which is connected to this interface to carry the correct data for classification. trustCiscoIPPhone(0) indicates that there is a restriction on trusting only ciscoIPPhone to carry the correct data for classification. If there is no bits turned on, any device connected to this interface is trusted to carry the correct data for clarification. This object is only instantiated if the platform supports trust device configuration. | 1.3.6.1.4.1.9.9.179.1.2.1.1.4 | Bits {trustCiscoIPPhone(0)} | read-write | current |
| caqIfOperTrustState OBJECT-TYPE This object is used to indicate the operational trust state of an interface. The operational trust state may or may not be identical to the config trust state denoted by caqIfTrustStateConfig. The value of this object depends on the runtime conditions such as whether the interface is configured to trust a certain type of device as denoted by caqIfTrustDevice as well as whether a device of the trusted type is connected to the interface. For example, if the interface is configured to only trust Cisco IP Phone and the phone is not connected to the interface at runtime, the operational trust state of this interface will have the untrusted(1) value even if the trustCoS(2) value is configured in caqIfTrustStateConfig. This object is only instantiated if the platform supports trust device configuration. If the object is untrusted(1), then the DSCP assigned to the packet is the DSCP specified by classification rule obtained from the matching ACE (Access Control Entry). ACE is a filter that is used to identify flows with certain characteristics. It includes fields such as ingress/egress ports, L2 addresses, L3 addresses , TCP/UDP port number. If this object is trustCoS(2), then the DSCP assigned to the packet is the layer2 CoS of the packet mapped to a DSCP by the CoS-to-DSCP mapping defined in object caqCosToDscpDscp. When this object is trustIpPrec(3), a DSCP is assigned to an IP packet according to the IP-Precedence-to-DSCP mapping defined by the values contained in caqIpPrecToDscpTable. For non-IP packets, trustIpPrec(3) has identical behavior as trustCoS(2). When this object is trustDscp(4), the DSCP contained in an IP packet is trusted as being the correct value to assign to it. For non-IP packets, trustDscp(4) has identical behavior as trustCoS(2). | 1.3.6.1.4.1.9.9.179.1.2.1.1.5 | INTEGER {untrusted(1), trustCoS(2), trustIpPrec(3), trustDscp(4)} | read-only | current |
| caqClassifierTable OBJECT-TYPE This table identifies which ACLs are in use on which interfaces. Some devices may impose constraints on the number of ACLs that can be attached to each interface; for example a constraint that at most three Qos ACLs, one for each type: IP, IPX and MAC, and at most three Security ACLs, one for each type: IP, IPX and MAC, can be attached to an interface. | 1.3.6.1.4.1.9.9.179.1.2.2 | not-accessible | current | |
| caqClassifierEntry OBJECT-TYPE An entry identifies that a particular ACL is in use on a particular interface. An interface can be a physical port or a VLAN. | 1.3.6.1.4.1.9.9.179.1.2.2.1 | not-accessible | current | |
| caqClassifierAclType OBJECT-TYPE Indicates the type of ACL attached to this interface. ipQos(1) indicates that this ACL is an IP Qos ACL. ipxQos(2) indicates that this ACL is an IPX Qos ACL. macQos(3) indicates that this ACL is a MAC Qos ACL. ipSecurity(4) indicates that this ACL is an IP Security ACL. ipxSecurity(5) indicates that this ACL is an IPX Security ACL. macSecurity(6) indicates that this ACL is a MAC Security ACL. | 1.3.6.1.4.1.9.9.179.1.2.2.1.1 | INTEGER {ipQos(1), ipxQos(2), macQos(3), ipSecurity(4), ipxSecurity(5), macSecurity(6)} | not-accessible | current |
| caqClassifierAclName OBJECT-TYPE Indicates the ACL name which should exist in the ACL tables e.g. in caqIpAceTable. This ACL can be a Qos ACL or a Security ACL. | 1.3.6.1.4.1.9.9.179.1.2.2.1.2 | CaqAclName | not-accessible | current |
| caqClassifierMapStatus OBJECT-TYPE The status of this classifier conceptual row entry. An entry may not exist in the active state unless the ACL name denoted by caqClassifierAclName object in the entry exist and active (i.e. its RowStatus object is active(1)) in an ACL table. Once a row becomes active, value in any other column within such row cannot be modified except by setting caqClassifierMapStatus to notInService(2) for such row. | 1.3.6.1.4.1.9.9.179.1.2.2.1.3 | RowStatus | read-create | current |
| caqClassifierMapDirection OBJECT-TYPE Indicates whether this ACL are to be attached to ingress or egress direction. | 1.3.6.1.4.1.9.9.179.1.2.2.1.4 | Bits {ingress(0), egress(1)} | read-create | current |
| caqIfSecurityAclConfigTable OBJECT-TYPE A list of the interfaces which support the security ACL feature. | 1.3.6.1.4.1.9.9.179.1.2.3 | not-accessible | current | |
| caqIfSecurityAclConfigEntry OBJECT-TYPE An entry contains configuration information about a security ACL mapped to a interface which is capable for this feature. | 1.3.6.1.4.1.9.9.179.1.2.3.1 | not-accessible | current | |
| caqIfSecurityAclBase OBJECT-TYPE The security ACL configuration mode for an interface. Setting this variable to the value port(1) will cause the packets (L3 forwarded packets and L2 packets) arriving at that interface to be filtered based on the ACL mapped to that interface. Setting this variable to the value vlan(2) will cause the packets (L3 forwarded packets and L2 packets) arriving at that access interface to be filtered based on two ACL(the router's ACL and the ACL of the VLAN to which the interface belongs). If it is a trunking interface, the vlan-tag packets will be filtered based on the ACL of the tag-vlan. Setting this variable to the value merge(3) will merge the physical interface ACL, the VLAN ACL and the router ACL together to emulate the logical serial model shown below. L3 only Port ACL -> VLAN ACL -> Router ACL -> Router ACL -> VLAN ACL physical ingress ingress egress egress interface | 1.3.6.1.4.1.9.9.179.1.2.3.1.1 | INTEGER {port(1), vlan(2), merge(3)} | read-write | current |
| caqIpOperClassifierTable OBJECT-TYPE This table identifies which operational IP ACLs are in use on which interfaces. | 1.3.6.1.4.1.9.9.179.1.2.4 | not-accessible | current | |
| caqIpOperClassifierEntry OBJECT-TYPE An entry in this table identifies operational IP ACLs that are currently in use on a particular interface. An interface can be a physical port or a VLAN. | 1.3.6.1.4.1.9.9.179.1.2.4.1 | not-accessible | current | |
| caqIpOperAclFeature OBJECT-TYPE An index indicates the feature to which the operational IP ACLs mapped at this interface are applied. 'ingressIpQos' indicates the ACL mapped at this interface is used to classify ingress IP traffic for QoS feature. 'egressIpQos' indicates the ACL mapped at this interface is used to classify egress IP traffic for QoS feature. 'ipSecurity' indicates the ACL mapped at this interface is used to classify IP traffic for security feature. | 1.3.6.1.4.1.9.9.179.1.2.4.1.1 | INTEGER {ingressIpQos(1), egressIpQos(2), ipSecurity(3)} | not-accessible | current |
| caqIpOperAclName OBJECT-TYPE This object indicates the name of an operational IP ACL which is mapped at this interface to classify IP traffic for feature denoted by caqIpOperAclFeature object. | 1.3.6.1.4.1.9.9.179.1.2.4.1.2 | SnmpAdminString | read-only | current |
| caqIpOperAclMapSource OBJECT-TYPE This object indicates the sources that map the operational IP ACLs at this interface. 'configured' indicates that the ACL mapping is introduced by manual configuration through CLI or an NMS application. 'dot1x' indicates that the ACL mapping is introduced by the operation of 802.1x feature. 'macAuth' indicates that the ACL mapping is introduced by the operation of Mac Authentication Bypass feature. 'webAuth' indicates that the ACL mapping is introduced by the operation of Web Authentication feature. 'eou' indicates that the ACL mapping is introduced by the operation of Extensible Authentication Protocol over UDP (EOU) feature. | 1.3.6.1.4.1.9.9.179.1.2.4.1.3 | Bits {configured(0), dot1x(1), macAuth(2), webAuth(3), eou(4)} | read-only | current |
| caqDownloadClassifierTable OBJECT-TYPE This table identifies ACLs assignment to capable interface which is downloaded using different security features. | 1.3.6.1.4.1.9.9.179.1.2.5 | not-accessible | current | |
| caqDownloadClassifierEntry OBJECT-TYPE An entry identifies ACLs assignment on a capable physical interface. | 1.3.6.1.4.1.9.9.179.1.2.5.1 | not-accessible | current | |
| caqDownloadAclFeature OBJECT-TYPE This object indicates the feature that ACLs mapped at this interface is used for. 'ingressIpQos' indicates the ACL mapped at this interface is used to classify ingress IP traffic for QoS feature. 'egressIpQos' indicates the ACL mapped at this interface is used to classify egress IP traffic for QoS feature. 'ipSecurity' indicates the ACL mapped at this interface is used to classify IP traffic for security feature. | 1.3.6.1.4.1.9.9.179.1.2.5.1.1 | INTEGER {ingressIpQos(1), egressIpQos(2), ipSecurity(3)} | not-accessible | current |
| caqDownloadClassifierAclName OBJECT-TYPE This object indicates the ACL name mapped to this interface to classify traffic for a specific feature denoted by the corresponding caqDownloadAclFeature. | 1.3.6.1.4.1.9.9.179.1.2.5.1.2 | CaqAclName | read-only | current |
| caqDownloadMapSource OBJECT-TYPE This object indicates the source that maps the ACLs at this interface. 'dot1x' indicates that the ACL mapping is introduced by the operation of 802.1x feature. 'macAuth' indicates that the ACL mapping is introduced by the operation of Mac Authentication Bypass feature. | 1.3.6.1.4.1.9.9.179.1.2.5.1.3 | INTEGER {dot1x(1), macAuth(2)} | read-only | current |
| caqDownloadAclType OBJECT-TYPE This object indicates the type of the ACL. 'pacl' indicates this is a port-based ACL. 'vacl' indicates this is a VLAN-based ACL. | 1.3.6.1.4.1.9.9.179.1.2.5.1.4 | INTEGER {pacl(1), vacl(2)} | read-only | current |
| caqAclObjects OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.179.1.3 | |||
| caqAclCapabilities OBJECT-TYPE Indicates what ACL capabilities are supported on the device. An ACL belongs to one of the following types: IP, IPX and MAC. Furthermore, an ACL can be used for either QoS or Security feature. If ipQos(0) bit is turned on, caqIpAceTable can be instantiated for Qos feature, otherwise it can not. If ipxQos(1) bit is turned on, caqIpxAceTable can be instantiated for Qos feature, otherwise it can not. If macQos(2) bit is turned on, caqMacAceTable can be instantiated for Qos feature, otherwise it can not. If ipSecurity(3) bit is turned on, caqIpAceTable can be instantiated for Security feature, otherwise it can not. If ipxSecurity(4) bit is turned on, caqIpxAceTable can be instantiated for Security feature, otherwise it can not. If macSecurity(5) bit is turned on, caqMacAceTable can be instantiated for Security feature, otherwise it can not. | 1.3.6.1.4.1.9.9.179.1.3.1 | Bits {ipQos(0), ipxQos(1), macQos(2), ipSecurity(3), ipxSecurity(4), macSecurity(5)} | read-only | current |
| caqIpAceTable OBJECT-TYPE This table contains a list of IP ACEs. Each ACE consists of a filter specification and behavior associated with it which describes what action to carry out on packets which match. An ACL is defined as the set of ACEs of the same type (all QoS, or all Security). Within a feature (qos or security), each ACE is named by a combination of an AclName and an ACE index, such that all the ACEs which are named using the same AclName are part of the same ACL. | 1.3.6.1.4.1.9.9.179.1.3.2 | not-accessible | current | |
| caqIpAceEntry OBJECT-TYPE An entry defines an ACE, consisting of a set of match criteria. For a packet to match an entry, it has to match all the criteria specified in that entry. | 1.3.6.1.4.1.9.9.179.1.3.2.1 | not-accessible | current | |
| caqIpAceFeature OBJECT-TYPE Indicates whether this entry is a Qos ACL or Security ACL. ACEs belongs to the same ACL should have the same value for this object. | 1.3.6.1.4.1.9.9.179.1.3.2.1.1 | INTEGER {qos(1), security(2)} | not-accessible | current |
| caqIpAclName OBJECT-TYPE The name of an ACL. Within a feature (qos or security), the name is unique across all of the ACL tables that identifies the list to which the entry belongs in the device. | 1.3.6.1.4.1.9.9.179.1.3.2.1.2 | CaqAclName | not-accessible | current |
| caqIpAceIndex OBJECT-TYPE The index of an ACE within an ACL. | 1.3.6.1.4.1.9.9.179.1.3.2.1.3 | Unsigned32 (1..65535) | not-accessible | current |
| caqIpAceMatchedAction OBJECT-TYPE Indicates the action to be taken if a packet matches this ACE. If the value of this ACE's caqIpAceFeature object is: 'qos(1)', then this object contains the index of an active row in caqQosActionSelectTable. If the value of this ACE's caqIpAceFeature object is: 'security(2)', then this object contains the index of an active row in caqSecurityActionTable. | 1.3.6.1.4.1.9.9.179.1.3.2.1.4 | Unsigned32 (1..65535) | read-create | current |
| caqIpAceProtocolType OBJECT-TYPE The protocol number field in the IP header used to indicate the higher layer protocol as specified in RFC 1700. A value value of 0 matches every IP packet. For example : 0 is IP, 1 is ICMP, 2 is IGMP, 4 is IP in IP encapsulation, 6 is TCP, 9 is IGRP, 17 is UDP, 47 is GRE, 50 is ESP, 51 is AH, 88 is IGRP, 89 is OSPF, 94 is KA9Q/NOS compatible IP over IP, 103 is PIMv2, 108 is PCP. | 1.3.6.1.4.1.9.9.179.1.3.2.1.5 | Unsigned32 (0..255) | read-create | current |
| caqIpAceAddrType OBJECT-TYPE The type of IP address used by this ACE entry. | 1.3.6.1.4.1.9.9.179.1.3.2.1.6 | InetAddressType | read-only | current |
| caqIpAceSrcIp OBJECT-TYPE The specified source IP address. The packet's source address is AND-ed with the value of caqIpAceSrcIpMask and then compared against the value of this object. If this object value is 0.0.0.0, and the value of caqIpAceSrcIpMask object in the same entry is 255.255.255.255, this entry matches any source IP address. | 1.3.6.1.4.1.9.9.179.1.3.2.1.7 | InetAddress | read-create | current |
| caqIpAceSrcIpMask OBJECT-TYPE The specified source IP address mask. | 1.3.6.1.4.1.9.9.179.1.3.2.1.8 | InetAddress | read-create | current |
| caqIpAceSrcPortOp OBJECT-TYPE Indicates how a packet's source TCP/UDP port number is to be compared. If the caqIpAceProtocolType object in the same row does not indicate TCP or UDP, this object has to be 'noOperator(1)' and cannot be changed while this row is active, i.e., the value of caqIpAceStatus in the same row has the value 'active(1)'. 'noOperator(1)', which is the default value, means that no comparison is to be made with the source TCP/UDP port number. lt(2) means less than, gt(3) means greater than, eq(4) means equal, neq(5) means not equal. Those 4 operators are using the caqIpAceSrcPort object as an operand which is the only one needed. range(6) means that it compares the port value between two numbers, so this operator needs 2 operands. One operand is the starting port number of the range which is caqIpAceSrcPort object, and the other operand is the ending port number of the range which the caqIpAceSrcPortRange object is in. | 1.3.6.1.4.1.9.9.179.1.3.2.1.9 | INTEGER {noOperator(1), lt(2), gt(3), eq(4), neq(5), range(6)} | read-create | current |
| caqIpAceSrcPort OBJECT-TYPE The source port number of the TCP or UDP protocol. If the caqIpAceSrcPortOp object in the same row is range(6), this object will be the starting port number of the port range. This object cannot be configured if caqIpAceStatus in the same row is active(1) or caqIpAceSrcPortOp in the same row is noOperator(1). | 1.3.6.1.4.1.9.9.179.1.3.2.1.10 | Unsigned32 (0..65535) | read-create | current |
| caqIpAceSrcPortRange OBJECT-TYPE The source port number of the TCP or UDP protocol. If the caqIpAceSrcPortOp object in the same row is range(6), this object will be the ending port number of the port range. This object cannot be configured if caqIpAceStatus in the same row is active(1) or caqIpAceSrcPortOp in the same row is not range(6). | 1.3.6.1.4.1.9.9.179.1.3.2.1.11 | Unsigned32 (0..65535) | read-create | current |
| caqIpAceDestIp OBJECT-TYPE The specified destination IP address. The packet's destination address is AND-ed with the value of caqIpAceDestIpMask and then compared against the value of this object. If this object value is 0.0.0.0 and the value of caqIpAceDestIpMask object in the same entry is 255.255.255.255, this entry matches any destination IP address. | 1.3.6.1.4.1.9.9.179.1.3.2.1.12 | InetAddress | read-create | current |
| caqIpAceDestIpMask OBJECT-TYPE The specified destination IP address mask. | 1.3.6.1.4.1.9.9.179.1.3.2.1.13 | InetAddress | read-create | current |
| caqIpAceDestPortOp OBJECT-TYPE Indicates how a packet's destination TCP/UDP port number is to be compared. If the caqIpAceProtocolType object in the same row does not indicate TCP or UDP, this object has to be 'noOperator(1)' and cannot be changed while this row is active, i.e., the value of caqIpAceStatus in the same row has the value 'active(1)'. 'noOperator(1)', which is the default value, means that no comparison is to be made with the destination TCP/UDP port number. lt(2) means less than. gt(3) means greater than. eq(4) means equal. neq(5) means not equal. Those 4 operators are using the caqIpAceDestPort object as an operand which is the only one needed. range(6) means that it compares the port value between two numbers, so this operator needs 2 operands. One operand is the starting port number of the range which is caqIpAceDestPort object, and the other operand is the ending port number of the range which the caqIpAceDestPortRange object is in. | 1.3.6.1.4.1.9.9.179.1.3.2.1.14 | INTEGER {noOperator(1), lt(2), gt(3), eq(4), neq(5), range(6)} | read-create | current |
| caqIpAceDestPort OBJECT-TYPE The destination port number of the TCP or UDP protocol. If the caqIpAceDestPortOp object in the same row is range(6), this object will be the starting port number of the port range. This object cannot be configured if caqIpAceStatus in the same row is active(1) or caqIpAceDestPortOp in the same row is noOperator(1). | 1.3.6.1.4.1.9.9.179.1.3.2.1.15 | Unsigned32 (0..65535) | read-create | current |
| caqIpAceDestPortRange OBJECT-TYPE The destination port number of the TCP or UDP protocol. If the caqIpAceDestPortOp object in the same row is range(6), this object will be the ending port number of the port range. This object cannot be configured if caqIpAceStatus in the same row is active(1) or caqIpAceDestPortOp in the same row is not range(6). | 1.3.6.1.4.1.9.9.179.1.3.2.1.16 | Unsigned32 (0..65535) | read-create | current |
| caqIpAceTosMatchCriteria OBJECT-TYPE Indicates what field of Tos octet in the packet header to be matched. none(1) means that there is no need to match the ToS octet. matchDscp(2) means that the DSCP value of packet header need to be matched. If this value is specified, the caqIpAceDscp object in the same row should be configured. matchIpPrec(3) means that the IpPrecedence value of packet header need to be matched. If this value is specifed, the caqIpAceIpPrec object in the same row should be configured. | 1.3.6.1.4.1.9.9.179.1.3.2.1.17 | INTEGER {none(1), matchDscp(2), matchIpPrec(3)} | read-create | current |
| caqIpAceIpPrec OBJECT-TYPE Specifies the IP precedence value to be matched against. This object could not be configured when the status of the entry, caqIpAceStatus, is active(1). The value of this object is ignored whenever the value of caqIpAceTosMatchCritial object is not matchIpPrec(3). | 1.3.6.1.4.1.9.9.179.1.3.2.1.18 | CaqIpPrecedence | read-create | current |
| caqIpAceDscp OBJECT-TYPE Specifies the Dscp value to be matched against. This object could not be configured when the status of the entry, caqIpAceStatus, is active(1). Packets can be matched the DSCP level from 0 to 63. The value of this object is ignored whenever the value of caqIpAceTosMatchCritial object is not matchDscp(2). | 1.3.6.1.4.1.9.9.179.1.3.2.1.19 | Dscp | read-create | current |
| caqIpAceProtocolMatchCriteria OBJECT-TYPE Indicates what field in the packet header for ICMP or IGMP or TCP protocol or IPv4 ESP (Enscrypted Security Payload) to be matched. none(1) = no comparison is to be done for ICMP/IGMP/TCP/ESP. matchIgmpType(2) means that the Type field of IGMP protocol packet header needs to be matched. If this value is specified, the caqIpAceIgmpType object in the same row should be configured. matchIcmpType(3) means that the Type field of ICMP protocol packet header needs to be matched. If this value is specified, the caqIpAceIcmpType object in the same row should be configured. matchIcmpTypeAndCode(4) means that both the Type and Code fields of ICMP protocol packet header need to be matched. If this value is specified, the caqIpAceIcmpType and caqIpAceIcmpCode object in the same row should be configured. matchEstablished(5) means that a match occurs if the TCP packet has the ACK or RST bits set. The non matching case is that of the intial TCP packet to form a connection. matchSecurityId(6) means that the Security Association Identifier field of IPv4 ESP packet header needs to be matched. If this value is specified, the caqIpAceSecurityId object in the same row should be configured. matchEapoudp(7) means that this ACE needs to be matched against the criteria for EAP (Extensible Authentication Protocol) over UDP purpose. matchUrlRedirect(8) means that this ACE needs to be matched against the criteria for URL redirection purpose. | 1.3.6.1.4.1.9.9.179.1.3.2.1.20 | INTEGER {none(1), matchIgmpType(2), matchIcmpType(3), matchIcmpTypeAndCode(4), matchEstablished(5), matchSecurityId(6), matchEapoudp(7), matchUrlRedirect(8)} | read-create | current |
| caqIpAceIcmpType OBJECT-TYPE Indicates the message type of ICMP packets. The type is a number from 0 to 255. The value of this object is ignored whenever the value of caqIpAceProtocolMatchCritial object is not matchIcmpType(3) or matchIcmpTypeAndCode(4). | 1.3.6.1.4.1.9.9.179.1.3.2.1.21 | Unsigned32 (0..255) | read-create | current |
| caqIpAceIcmpCode OBJECT-TYPE Indicates the message code of ICMP packets. The code is a number from 0 to 255. The value of this object is ignored whenever the value of caqIpAceProtocolMatchCritial object is not matchIcmpTypeAndCode(4). | 1.3.6.1.4.1.9.9.179.1.3.2.1.22 | Unsigned32 (0..255) | read-create | current |
| caqIpAceIgmpType OBJECT-TYPE Indicates the message type of IGMP packets. The code is a number from 0 to 15. The value of this object is ignored whenever the value of caqIpAceProtocolMatchCritial object is not matchIgmpType(2). | 1.3.6.1.4.1.9.9.179.1.3.2.1.23 | Unsigned32 (0..15) | read-create | current |
| caqIpAceOrderPosition OBJECT-TYPE The ordering position of this ACE in the ACL. If this entry is not in active(1) state, this object has value of 0. | 1.3.6.1.4.1.9.9.179.1.3.2.1.24 | Unsigned32 (0..65535) | read-only | current |
| caqIpAceBeforePosition OBJECT-TYPE The object is to control the position of an ACE in the ACL. Indicates the order position of a new ACE before an active ACE which is already in the ACL. It means that the new ACE will replace the position of the ACE which the object specifies. For example, if there are 6 ACEs in an ACL, so the positions of those 6 ACEs will be 1, 2, 3, 4, 5, 6. If the user would like to add a new ACE and specifies 4 to be the value of this object, the old ACEs in positions, 4, 5, 6 will become 5, 6, 7 while the entry containing the new ACE is active. Be careful, for example, if the user would like to move an ACE whose position is 2 to before the ACE whose position is 5. He put the status of that entry to in-active and the position order will be 1, 2, 3, 4, 5. The old ACEs in positions 3, 4, 5, 6 becomes 2, 3, 4, 5. So, the user has to specify the object to 4, because the ACE in old position 5 has been moved to position 4. If not specified, the default value 0 will be used. And the new ACE is appended to the end of the ACL. 0 will be always returned if the status of this row is active. If the entry is from active(1) to notInService(2), this object should have default value. | 1.3.6.1.4.1.9.9.179.1.3.2.1.25 | Unsigned32 (0..65535) | read-create | current |
| caqIpAceStatus OBJECT-TYPE The status of this IP ACE conceptual row entry. This object is used to manage creation, deletion and modification of rows in this table. An entry may not exist in the active state unless all objects in the entry have an appropriate value. Especially, it cannot be in active state unless the caqIpAceMatchedAction object in the entry point to an active entry (i.e its RowStatus object is active(1)) in the caqQosActionSelectTable or caqSecurityActionTable. Once a row becomes active, value in any other column within such row cannot be modified. If this row is the only ACE in an ACL and the value of its caqIpAclName object matches the value of caqClassifierAclName object in any active entry of the caqClassifierTable, removing this entry will also remove the associated entry in the caqClassifierTable. If the value of caqIpAceType in this row is 'systemGenerated', this row cannot be deleted or modified. | 1.3.6.1.4.1.9.9.179.1.3.2.1.26 | RowStatus | read-create | current |
| caqIpAceSecurityId OBJECT-TYPE Indicates the Security Association Identifier of IPv4 ESP packets. The value of this object is ignored whenever the value of caqIpAceProtocolMatchCritial object is not matchSecurityId(6). | 1.3.6.1.4.1.9.9.179.1.3.2.1.27 | Unsigned32 (0 | 4..233) | read-create | current |
| caqIpAceSrcGroup OBJECT-TYPE Indicates the source group name which the source IP address in the IP packet header belongs to. If this object is configured, the value of caqIpAceProtocolType object in the same row will have the value of 0. | 1.3.6.1.4.1.9.9.179.1.3.2.1.28 | SnmpAdminString | read-create | current |
| caqIpAceDestGroup OBJECT-TYPE Indicates the destination group name which the destination IP address in the IP packet header belongs to. If this object is configured, the value of caqIpAceProtocolType object in the same row will have the value of 0. | 1.3.6.1.4.1.9.9.179.1.3.2.1.29 | SnmpAdminString | read-create | current |
| caqIpAceType OBJECT-TYPE Indicates the ACE type. | 1.3.6.1.4.1.9.9.179.1.3.2.1.30 | INTEGER {configured(1), systemGenerated(2)} | read-only | current |
| caqIpxAceTable OBJECT-TYPE This table contains a list of IPX ACEs. Each ACE consists of a filter specification and behavior associated with it which describes what action to carry out on packets which match. An ACL is defined as the set of ACEs of the same type (all QoS, or all Security). Within each feature (qos or security), each ACE is named by a combination of an AclName and an ACE index, such that all the ACEs which are named using the same AclName are part of the same ACL. This table is instantiated only if the ipxQos bit or ipxSecurity bit of caqAclCapabilities object is turned on. | 1.3.6.1.4.1.9.9.179.1.3.3 | not-accessible | current | |
| caqIpxAceEntry OBJECT-TYPE Each entry of caqIpxAceTable consists of a set of match creteria. For a IPX flow to match an entry, it has to match all the conditions specified in that entry. | 1.3.6.1.4.1.9.9.179.1.3.3.1 | not-accessible | current | |
| caqIpxAceFeature OBJECT-TYPE Indicates whether this entry is a Qos ACL or Security ACL. ACEs belongs to the same ACL should have the same value for this object. | 1.3.6.1.4.1.9.9.179.1.3.3.1.1 | INTEGER {qos(1), security(2)} | not-accessible | current |
| caqIpxAclName OBJECT-TYPE The name of an ACL. Within a feature (qos or security), this name is unique across all of the ACL tables that identifies the list to which the entry belongs in the device. | 1.3.6.1.4.1.9.9.179.1.3.3.1.2 | CaqAclName | not-accessible | current |
| caqIpxAceIndex OBJECT-TYPE The index of an IPX ACE within an ACL. | 1.3.6.1.4.1.9.9.179.1.3.3.1.3 | Unsigned32 (1..65535) | not-accessible | current |
| caqIpxAceMatchedAction OBJECT-TYPE Indicates the action to be taken if a packet matches this ACE. If the value of this ACE's caqIpxAceFeature object is: 'qos(1)', then this object contains the index of an active row in caqQosActionSelectTable. If the value of this ACE's caqIpxAceFeature object is: 'security(2)', then this object contains the index of an active row in caqSecurityActionTable. | 1.3.6.1.4.1.9.9.179.1.3.3.1.4 | Unsigned32 (1..65535) | read-create | current |
| caqIpxAceSrcNet OBJECT-TYPE Indicates the source network from which the packet is being sent. This is a 32-bits value that uniquely identifies network cable segment in IPX protocol. A network number of 0xFFFFFFFF matches all networks. | 1.3.6.1.4.1.9.9.179.1.3.3.1.5 | OCTET STRING (SIZE(4)) | read-create | current |
| caqIpxAceDestMatchCriteria OBJECT-TYPE Indicate which matches to be checked for the destination network of the flow. matchProtocol(0) means that the flow protocol will be matched against the value specified by caqIpxAceProtocolType object in the same row. matchIpxDestNet(1) means that the flow destination network will be matched against the value specified by caqIpxAceDestNet object in the same row. matchIpxDestNode(2) means that the flow destination node will be matched against the value specified by caqIpxAceDestNode object in the same row. If this option bit is on, the matchIpxDestNet(1) bit has to be on also. matchIpxDestNetMask(3) means that the packet's flow destination network will be AND-ed with the value specified by caqIpxAceDestNetMask object in the same row and then compared against the value of caqIpxAceDestNet object. matchIpxDestNodeMask(4) means that the packet's flow destination node will be AND-ed with the value specified by caqIpxAceDestNodeMask object in the same row and then compared against the value of caqIpxAceDestNode object. | 1.3.6.1.4.1.9.9.179.1.3.3.1.6 | Bits {matchProtocol(0), matchIpxDestNet(1), matchIpxDestNode(2), matchIpxDestNetMask(3), matchIpxDestNodeMask(4)} | read-create | current |
| caqIpxAceProtocolType OBJECT-TYPE The protocol number field in the IPX header used to indicate the higher layer protocol. It can be any, ncp, netbios, rip, sap or an integer between 0 to 255. | 1.3.6.1.4.1.9.9.179.1.3.3.1.7 | Unsigned32 (0..255) | read-create | current |
| caqIpxAceDestNet OBJECT-TYPE Number of the destination network to which the packet is being sent. This is a 32-bit value that uniquely identifies the IPX network cable segment in IPX protocol. A network number of 0xFFFFFFFF matches all networks. The value of this object is ignored whenever the matchIpxDestNet(1) and matchIpxDestNetMask(3) bits of caqIpxAceDestMatchCriteria object are not on. | 1.3.6.1.4.1.9.9.179.1.3.3.1.8 | OCTET STRING (SIZE(4)) | read-create | current |
| caqIpxAceDestNode OBJECT-TYPE Node on the destination network to which the packet is being sent. This is a 48 bits value. The value of this object is ignored whenever the matchIpxDestNode(2) and matchIpxDestNodeMask(4) bits of caqIpxAceDestMatchCriteria object are not on. | 1.3.6.1.4.1.9.9.179.1.3.3.1.9 | OCTET STRING (SIZE(6)) | read-create | current |
| caqIpxAceDestNetMask OBJECT-TYPE Mask to be applied to the destination net. This is an 32-bit value that has the same format as destination net. The value of this object is ignored whenever the matchIpxDestNetMask(3) bit of caqIpxAceDestMatchCriteria object is not on. | 1.3.6.1.4.1.9.9.179.1.3.3.1.10 | OCTET STRING (SIZE(4)) | read-create | current |
| caqIpxAceDestNodeMask OBJECT-TYPE Mask to be applied to the destination node. This is a 48-bit value. The value of this object is ignored whenever the matchIpxDestNodeMask(4) bit of caqIpxAceDestMatchCriteria object is not on. | 1.3.6.1.4.1.9.9.179.1.3.3.1.11 | OCTET STRING (SIZE(6)) | read-create | current |
| caqIpxAceOrderPosition OBJECT-TYPE The ordering position of this ACE in the ACL. If this entry is not in active(1) state, this object has value of 0. | 1.3.6.1.4.1.9.9.179.1.3.3.1.12 | Unsigned32 (0..65535) | read-only | current |
| caqIpxAceBeforePosition OBJECT-TYPE The object is to control the position of an ACE in the ACL. Specifies the order position of a new ACE before an active ACE which is already in the ACL. It means that the new ACE will replace the position of the ACE which the object specifies. For example, if there are 6 ACEs in an ACL, so the positions of those 6 ACEs will be 1, 2, 3, 4, 5, 6. If the user would like to add a new ACE and he specifies 4 to be the value of this object, the old ACEs in positions, 4, 5, 6 will become 5, 6, 7 while the entry containing the new ACE is active. The removing is similar. Be careful, for example, if the user would like to move an ACE whose position is 2 to before the ACE whose position is 5. He put the status of that entry to in-active and the position order will be 1, 2, 3, 4, 5. The old ACEs in positions 3, 4, 5, 6 becomes 2, 3, 4, 5. So, the user has to specify the object to 4, because the ACE in old position 5 has been moved to position 4. If not specified, the default value 0 will be used. And the new ACE is appended to the end of the ACL. 0 will be always returned if the status of this row is active. If the entry is from active(1) to notInService(2), this object should be default value. | 1.3.6.1.4.1.9.9.179.1.3.3.1.13 | Unsigned32 (0..65535) | read-create | current |
| caqIpxAceStatus OBJECT-TYPE The status of this IPX ACE conceptual row entry. This object is used to manage creation, deletion and modification of rows in this table. An entry may not exist in the active state unless all objects in the entry have an appropriate value. Especially, it cannot be in active state unless the caqIpxAceMatchedAction object in the entry point to an active entry (i.e its RowStatus object is active(1)) in the caqQosActionSelectTable or caqSecurityActionTable. Once a row becomes active, value in any other column within such row cannot be modified. If this row is the only ACE in an ACL and the value of its caqIpxAclName object matches the value of caqClassifierAclName object in any active entry of the caqClassifierTable, removing this entry will also remove the associated entry in the caqClassifierTable. | 1.3.6.1.4.1.9.9.179.1.3.3.1.14 | RowStatus | read-create | current |
| caqMacAceTable OBJECT-TYPE This table contains a list of MAC ACEs. Each ACE consists of a filter specification and behavior associated with it which describes what action to carry out on packets which match. An ACL is defined as the set of ACEs of the same type (all QoS, or all Security). Within a feature (qos or security), each ACE is named by a combination of an AclName and an ACE index, such that all the ACEs which are named using the same AclName are part of the same ACL. This table is instantiated only if the macQos bit or macSecurity bit of caqAclCapabilities object is turned on. | 1.3.6.1.4.1.9.9.179.1.3.4 | not-accessible | current | |
| caqMacAceEntry OBJECT-TYPE Each entry of caqMacAceTable consist of a set of match criteria. For a layer 2 flow to match an entry, it has to match all the conditions specified in that entry. | 1.3.6.1.4.1.9.9.179.1.3.4.1 | not-accessible | current | |
| caqMacAceFeature OBJECT-TYPE Indicates whether this entry is a Qos ACL or Security ACL. | 1.3.6.1.4.1.9.9.179.1.3.4.1.1 | INTEGER {qos(1), security(2)} | not-accessible | current |
| caqMacAclName OBJECT-TYPE The name of an ACL. Within a feature (qos or security), this name is unique across all the ACL tables that identifies the list to which the entry belongs in the device. | 1.3.6.1.4.1.9.9.179.1.3.4.1.2 | CaqAclName | not-accessible | current |
| caqMacAceIndex OBJECT-TYPE The index of an Mac ACE within an ACL. | 1.3.6.1.4.1.9.9.179.1.3.4.1.3 | Unsigned32 (1..65535) | not-accessible | current |
| caqMacAceMatchedAction OBJECT-TYPE Indicates the action to be taken if a packet matches this ACE. If the value of this ACE's caqMacAceFeature object is: 'qos(1)', then this object contains the index of an active row in caqQosActionSelectTable. If the value of this ACE's caqMacAceFeature object is: 'security(2)', then this object contains the index of an active row in caqSecurityActionTable. | 1.3.6.1.4.1.9.9.179.1.3.4.1.4 | Unsigned32 (1..65535) | read-create | current |
| caqMacAceSrcMac OBJECT-TYPE Indicates the 48 bits source MAC address. The packet's source address is AND-ed with the value of caqMacAceSrcMacMask and then compared against the value of this object. If this object value is 00-00-00-00-00-00, and the value of caqMacAceSrcMacMask object in the same entry is ff-ff-ff-ff-ff-ff, this entry matches any source Mac address. | 1.3.6.1.4.1.9.9.179.1.3.4.1.5 | MacAddress | read-create | current |
| caqMacAceSrcMacMask OBJECT-TYPE Indicates the 48 bit source MAC address mask. | 1.3.6.1.4.1.9.9.179.1.3.4.1.6 | MacAddress | read-create | current |
| caqMacAceDestMac OBJECT-TYPE Indicates the 48 bits destination MAC address. The packet's destination address is AND-ed with the value of caqMacAceDestMacMask and then compared against the value of this object. If this object value is 00-00-00-00-00-00, and the value of caqMacAceDestMacMask object in the same entry is ff-ff-ff-ff-ff-ff, this entry matches any destionation Mac address. | 1.3.6.1.4.1.9.9.179.1.3.4.1.7 | MacAddress | read-create | current |
| caqMacAceDestMacMask OBJECT-TYPE Indicates the 48 bit destination MAC address mask. | 1.3.6.1.4.1.9.9.179.1.3.4.1.8 | MacAddress | read-create | current |
| caqMacAceEthertype OBJECT-TYPE This 16-bit hexadecimal number indicates the matched Ethernet type. 0x0000 means any Ethernet type will be matched. | 1.3.6.1.4.1.9.9.179.1.3.4.1.9 | Unsigned32 (0..65535) | read-create | current |
| caqMacAceOrderPosition OBJECT-TYPE The ordering position of this ACE in the ACL. If this entry is not in active(1) state, this object has value of 0. | 1.3.6.1.4.1.9.9.179.1.3.4.1.10 | Unsigned32 (0..65535) | read-only | current |
| caqMacAceBeforePosition OBJECT-TYPE The object is to control the position of an ACE in the ACL. Specifies the order position of a new ACE before a ACE which is already in the ACL. It means that the new ACE will replace the position of the ACE which the object specifies. For example, if there are 6 ACEs in an ACL, so the positions of those 6 ACEs will be 1, 2, 3, 4, 5, 6. If the user would like to add a new ACE and he specifies 4 to be the value of this object, the old ACEs in positions, 4, 5, 6 will become 5, 6, 7 while the entry containing the new ACE is active. The removing is similar. Be careful, for example, if the user would like to move an ACE whose position is 2 to before the ACE whose position is 5. He put the status of that entry to in-active and the position order will be 1, 2, 3, 4, 5. The old ACEs in positions 3, 4, 5, 6 becomes 2, 3, 4, 5. So, the user has to specify the object to 4, because the ACE in old position 5 has been moved to position 4. If not specified, the default value 0 will be used. And the new ACE is appended to the end of the ACL. 0 will be always returned if the status of this row is active. If the entry is from active to notInService, this object should has default value. | 1.3.6.1.4.1.9.9.179.1.3.4.1.11 | Unsigned32 (0..65535) | read-create | current |
| caqMacAceStatus OBJECT-TYPE The status of this MAC ACE conceptual row entry. This object is used to manage creation, deletion and modification of rows in this table. An entry may not exist in the active state unless all objects in the entry have an appropriate value. Especially, it cannot be in active state unless the caqMacAceMatchedAction object in the entry point to an active entry (i.e its RowStatus object is active(1)) in the caqQosActionSelectTable or caqSecurityActionTable. Once a row becomes active, value in any other column within such row cannot be modified. If this row is the only ACE in an ACL and the value of its caqMacAclName object matches the value of caqClassifierAclName object in any active entry of the caqClassifierTable, removing this entry will also remove the associated entry in the caqClassifierTable. | 1.3.6.1.4.1.9.9.179.1.3.4.1.12 | RowStatus | read-create | current |
| caqMacAceMatchCriteria OBJECT-TYPE Indicates which field in the packet header to be matched. matchCos(0) means that the packet Cos value will be matched against the value specified by caqMacAceCos object in the same row. matchVlan(1) means that the packet VLAN value will be matched against the value specified by caqMacAceVlan object in the same row. | 1.3.6.1.4.1.9.9.179.1.3.4.1.13 | Bits {matchCos(0), matchVlan(1)} | read-create | current |
| caqMacAceCos OBJECT-TYPE Indicates the packet Cos value to be matched. The value of this object is ignored whenever the matchCos(0) bit of caqMacAceMatchCriteria object is not on. | 1.3.6.1.4.1.9.9.179.1.3.4.1.14 | QosLayer2Cos | read-create | current |
| caqMacAceVlan OBJECT-TYPE Indicates the packet VLAN number to be matched. The value of this object is ignored whenever the matchVlan(1) bit of caqMacAceMatchCriteria object is not on. | 1.3.6.1.4.1.9.9.179.1.3.4.1.15 | VlanIndex | read-create | current |
| caqFlowPolicingCpb OBJECT-TYPE Indicates the flow policing capability of the device. microFlow(0) indicates that microflow can be policed. aggregate(1) indicates that aggregate flow can be policed. | 1.3.6.1.4.1.9.9.179.1.3.5 | Bits {microFlow(0), aggregate(1)} | read-only | current |
| caqQosActionSelectTable OBJECT-TYPE This table describes the actions of ACEs. Once an ACE is matched, it follows its MatchedAction object to an entry of this table to get an action for the matching ACE. An action includes policer information as well as an DSCP associated with trust state information of the matching ACE. | 1.3.6.1.4.1.9.9.179.1.3.6 | not-accessible | current | |
| caqQosActionSelectEntry OBJECT-TYPE An entry of an ACE action. It links to the entries of caqFlowPolicerTable with caqQosActionSelectMicroflow, caqQosActionSelectAggregate objects. | 1.3.6.1.4.1.9.9.179.1.3.6.1 | not-accessible | current | |
| caqQosActionSelectIndex OBJECT-TYPE The index of this table for indicating an ACE Action for QoS. | 1.3.6.1.4.1.9.9.179.1.3.6.1.1 | Unsigned32 (1..65535) | not-accessible | current |
| caqQosActionSelectTrust OBJECT-TYPE Determines if the packets matching the ACE should be trusted or if a specific DSCP should be assigned to it. If trustCos(2) is specified, the final DSCP value should refer to caqCosToDscpDscp object in caqCosToDscpTable to transfer layer 2 CoS value to DSCP value. If trustIpPrec(3) is specified, the final DSCP value should refer to caqIpPrecToDscpDscp object in caqIpPrecToDscpTable to transfer IP Precedence value to DSCP value. If trustDscp(4) is specified, the final DSCP value is the one which packets carry. If noTrust(1) is specified, the final DSCP value will have the value of caqQosActionSelectDscp object. That is, if an instance of this object is noTrust(1), the caqQosActionSelectStatus object can not become 'active(1)' until a value has been assigned to the corresponding instance of caqQosActionSelectDscp. | 1.3.6.1.4.1.9.9.179.1.3.6.1.2 | INTEGER {noTrust(1), trustCos(2), trustIpPrec(3), trustDscp(4)} | read-create | current |
| caqQosActionSelectDscp OBJECT-TYPE This object is only instantiated when the caqQosActionSelectTrust object in the same entry has been set to noTrust(1). | 1.3.6.1.4.1.9.9.179.1.3.6.1.4 | Dscp | read-create | current |
| caqQosActionSelectMicroflow OBJECT-TYPE Indicates a policer name. The value of this object either matches the value of caqFlowPolicerName object of an active entry in caqFlowPolicerTable or has an empty string value. The ACE uses this object to link to a policer flow entry. If there is no microflow policer defined for the ACE pointed to this entry, this object should be an empty string. If the microflow(0) bit of caqFlowPolicingCpb object is turned off, this object should also be an empty string. Otherwise it should match the value of caqFlowPolicerName of an entry in the caqFlowPolicerTable which has its RowStatus value to be active(1) and the type of the policer should be microflow(1). | 1.3.6.1.4.1.9.9.179.1.3.6.1.5 | CaqPolicerNameOrEmpty | read-create | current |
| caqQosActionSelectAggregate OBJECT-TYPE Indicates a policer name. The value of this object either matches the value of caqFlowPolicerName object of an active entry in caqFlowPolicerTable or has an empty string value. The ACE uses this object to link to a policer flow entry. If there is no aggregate policer defined for the ACE pointed to this entry, this object should be an empty string. If the aggregate(1) bit of caqFlowPolicingCpb object is turned off, this object should also be an an empty string. Otherwise it should match the value of caqFlowPolicerName of an entry in the caqFlowPolicerTable which has its RowStatus value to be active(1) and the type of the policer should be aggregate(2). | 1.3.6.1.4.1.9.9.179.1.3.6.1.6 | CaqPolicerNameOrEmpty | read-create | current |
| caqQosActionSelectStatus OBJECT-TYPE The status of this Qos Action Select conceptual row entry. This object is used to manage creation, deletion and modification of rows in this table. An entry may not exist in the active state unless all objects in the entry have an appropriate value. Once a row becomes active, value in any other column within such row cannot be modified. If this row is pointed to by an active entry in the ACL tables, this object cannot be changed from active(1) to any other value. | 1.3.6.1.4.1.9.9.179.1.3.6.1.7 | RowStatus | read-create | current |
| caqFlowPolicerExcessRateSupport OBJECT-TYPE Indicates whether the device supports excess rate configuration. | 1.3.6.1.4.1.9.9.179.1.3.7 | TruthValue | read-only | current |
| caqFlowPolicerTable OBJECT-TYPE This table defines the flow policing rules. A flow policing rule comprises a rate, burst size and drop-or-mark indication. | 1.3.6.1.4.1.9.9.179.1.3.8 | not-accessible | current | |
| caqFlowPolicerEntry OBJECT-TYPE The attributes defining a flow policing rule. | 1.3.6.1.4.1.9.9.179.1.3.8.1 | not-accessible | current | |
| caqFlowPolicerName OBJECT-TYPE The name of a policer. This name has to be unique to identify a microflow or an aggregate policer in the device. | 1.3.6.1.4.1.9.9.179.1.3.8.1.1 | CaqPolicerName | not-accessible | current |
| caqFlowPolicerType OBJECT-TYPE The type of this policer. | 1.3.6.1.4.1.9.9.179.1.3.8.1.2 | INTEGER {microflow(1), aggregate(2)} | read-create | current |
| caqFlowPolicerNormalRateRequest OBJECT-TYPE The requested average rate of the flow. The base unit of this object is 1 kilo-bits per second. 0 may be specified for a rate which causes all packets to be out-of-profile. Out-of-profile indicates that a packet causes the committed access rate of the packet's flow to be exceeded. Committed access rate is the bandwidth that has been committed to a specific flow or group of flows. The committed rate can be enforced by policing or by shaping. | 1.3.6.1.4.1.9.9.179.1.3.8.1.3 | Integer32 (0 | 32..8000000) | read-create | current |
| caqFlowPolicerNormalRateGrant OBJECT-TYPE The granted average rate of the flow. The base unit of this object is 1 kilo-bits per second. If the status of this row is not active, the value of this object will be the same as caqFlowPolicerNormalRateRequest's value. If the QoS function is enabled and the policy source is from local configuration, this MIB object is from the runtime hardware information. Due to hardware granularity, the granted value may not be the same as the value specified by caqFlowPolicerNormalRateRequest object. It will be the closest value to the requested one that the hardware can support. | 1.3.6.1.4.1.9.9.179.1.3.8.1.4 | Integer32 | read-only | current |
| caqFlowPolicerNormalRateAction OBJECT-TYPE The action for those normal rate out-of-profile packets. The action is to drop the packets or mark down its DSCP to the value of caqDscpMappingNRPolicedDscp defined in caqDscpMappingTable. If the caqFlowPolicerExcessRateSupport is true(1), this object cannot be set to drop(1). Setting the value of caqFlowPolicerExcessRateRequest object equal to the value of caqFlowPolicerNormalRateRequest object together with setting the value of caqFlowPolicerExcessRateAction object to drop(1) will effectively drop the packet at normal rate. | 1.3.6.1.4.1.9.9.179.1.3.8.1.5 | INTEGER {drop(1), policedDscp(2)} | read-create | current |
| caqFlowPolicerExcessRateRequest OBJECT-TYPE The requested excess rate of the flow. The base unit of this object is 1 kilo-bits per second. 0 may be specified for a rate which causes all packets to be out-of-profile. Out-of-profile indicates that a packet causes the committed access rate of the packet's flow to be exceeded. Committed access rate is the bandwidth that has been committed to a specific flow or group of flows. The committed rate can be enforced by policing or by shaping. If the caqFlowPolicerExcessRateSupport is false(2), this object cannot be instantiated. | 1.3.6.1.4.1.9.9.179.1.3.8.1.6 | Integer32 (0 | 32..8000000) | read-create | current |
| caqFlowPolicerExcessRateGrant OBJECT-TYPE The granted excess rate of the flow. The base unit of this object is 1 kilo-bits per second. If the status of this row is not active, the value of this object will be the same as caqFlowPolicerExcessRateRequest's value. If the QoS function is enabled and the policy source is from local configuration, this MIB object is from the runtime hardware information. Due to hardware granularity, the granted value may not be the same as the value specified by caqFlowPolicerExcessRateRequest object. It will be the closest value to the requested one that the hardware can support. If the caqFlowPolicerExcessRateSupport is false(2), this object cannot be instantiated. | 1.3.6.1.4.1.9.9.179.1.3.8.1.7 | Integer32 | read-only | current |
| caqFlowPolicerExcessRateAction OBJECT-TYPE The action for those excess rate out-of-profile packets. The action is to drop the packets or mark down its DSCP value to value of caqDscpMappingERPolicedDscp defined in caqDscpMappingTable. If the caqFlowPolicerExcessRateSupport is false(2), this object cannot be instantiated. | 1.3.6.1.4.1.9.9.179.1.3.8.1.8 | INTEGER {drop(1), policedDscp(2)} | read-create | current |
| caqFlowPolicerBurstSizeRequest OBJECT-TYPE The requested burst rate of the flow. The base unit of this object is 1 kilo-bits. | 1.3.6.1.4.1.9.9.179.1.3.8.1.9 | Integer32 (1..32000) | read-create | current |
| caqFlowPolicerBurstSizeGrant OBJECT-TYPE The granted burst rate of the flow. The base unit of this object is 1 kilo-bits. If the status of this row is not active, the value of this object will be the same as caqFlowPolicerBurstSizeRequest's value. If the QoS function is enabled and the policy source is from local configuration, this MIB object is from the runtime hardware information. Due to hardware granularity, the granted value may not be the same as the value specified by caqFlowPolicerBurstSizeRequest object. It will be the closest value to the requested one that the hardware can support. | 1.3.6.1.4.1.9.9.179.1.3.8.1.10 | Integer32 | read-only | current |
| caqFlowPolicerStatus OBJECT-TYPE The status of this flow policer conceptual row entry. This object is used to manage creation, deletion and modification of rows in this table. An entry may not exist in the active state unless all objects in the entry have an appropriate value. Once a row becomes active, value in any other column within such row cannot be modified. If this row is pointed to by an active entry in the caqQosActionSelectTable, this object cannot be changed from active(1) to any other value. | 1.3.6.1.4.1.9.9.179.1.3.8.1.11 | RowStatus | read-create | current |
| caqFlowPolicerExcessBurstRequest OBJECT-TYPE The requested excess burst size of the flow. If the caqFlowPolicerExcessBurstSupport is false(2), this object cannot be instantiated. | 1.3.6.1.4.1.9.9.179.1.3.8.1.12 | Unsigned32 (1..32000) | read-create | current |
| caqFlowPolicerExcessBurstGrant OBJECT-TYPE The granted excess burst size of the flow. If the status of this row is not active, the value of this object will be the same as caqFlowPolicerExcessBurstRequest's value. If the QoS function is enabled and the policy source is from local configuration, this MIB object is from the runtime hardware information. Due to hardware granularity, the granted value may not be the same as the value specified by caqFlowPolicerExcessBurstRequest object. It will be the closest value to the requested one that the hardware can support. If the caqFlowPolicerExcessBurstSupport is false(2), this object cannot be instantiated. | 1.3.6.1.4.1.9.9.179.1.3.8.1.13 | Unsigned32 (1..32000) | read-only | current |
| caqSecurityActionTable OBJECT-TYPE This table describes the actions of Security ACEs. Once an ACE is matched and it can go through an entry of this table to find the Security action. | 1.3.6.1.4.1.9.9.179.1.3.9 | not-accessible | current | |
| caqSecurityActionEntry OBJECT-TYPE An entry of a Security ACE action. It provides the action for for the traffic matching Security ACEs. | 1.3.6.1.4.1.9.9.179.1.3.9.1 | not-accessible | current | |
| caqSecurityActionIndex OBJECT-TYPE The index of this table for indicating a Security ACE action entry. | 1.3.6.1.4.1.9.9.179.1.3.9.1.1 | Unsigned32 (1..65535) | not-accessible | current |
| caqSecurityAction OBJECT-TYPE Determines the action that the device will take if the traffic matches the ACE. If permit(1) is specified, the matched traffic will be allowed through the device. If deny(2) is specified, the matched traffic will be blocked and dropped. If redirect(3) is specified, the matched traffic will be redirected to physical port(s) which should be configured in the caqSecurityRedirectPortList object. Redirect means taking packet coming in and putting it out of port(s) as is. If redirectWithAdj(4) is specified, the matched traffic will be redirected to the VLAN configured in the adjacency entry denoted by caqSecurityAdjIndex. If denyWithLog(5) is specified, the matched traffic will be blocked, dropped and logged. If denyArpInspection(6) is specified, the matched ARP traffic will be blocked and dropped. If denyArpInspWithLog(7) is specified, the matched ARP traffic will be blocked, dropped and logged. If permitArpInspection(8) is specified, the matched ARP traffic will be allowed through the device. if include(9) is specified, the matched trafic will be regulated according to the downloaded ACE type denoted by caqSecurityDownloadedAceFeature object. | 1.3.6.1.4.1.9.9.179.1.3.9.1.2 | INTEGER {permit(1), deny(2), redirect(3), redirectWithAdj(4), denyWithLog(5), denyArpInspection(6), denyArpInspWithLog(7), permitArpInspection(8), include(9)} | read-create | current |
| caqSecurityRedirectPortList OBJECT-TYPE Indicates the set of physical port(s) that matched traffic is redirected to. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of redirect ports; the port is not included if its bit has a value of '0'. The value of this object is ignored whenever the value of caqSecurityAction object in the same row is not redirect(3). | 1.3.6.1.4.1.9.9.179.1.3.9.1.3 | OCTET STRING (SIZE(0..128)) | read-create | deprecated |
| caqSecurityCapture OBJECT-TYPE Indicates whether the matched traffic is to be captured. Capture means the packet is not only switched normally but also a copy of the switched packet is transmitted on the capture port(s). Traffic which is dropped cannot be captured; only traffic that is forwarded to its appropriate destination, can also be forwarded to a capture port. Redirected traffic cannot be captured. Packets are only output on a capture port if they are on a VLAN which is carried on that port. To capture traffic from many vlans, the capture port(s) should be a trunk carrying the required vlans. The capturing destination port(s) should be configured in caqSecurityAclCaptureIfTable. | 1.3.6.1.4.1.9.9.179.1.3.9.1.4 | TruthValue | read-create | current |
| caqSecurityActionStatus OBJECT-TYPE The status of this Security ACE action conceptual row entry. This object is used to manage creation, deletion and modification of rows in this table. An entry may not exist in the active state unless all objects in the entry have appropriate value. If the value of caqSecurityAction object in the same row is redirectWithAdj(4), user must use the value of the index object of an active entry in caqAdjacencyTable to configure the caqSecurityAdjIndex object. Once a row becomes active, value in any other column within such row cannot be modified. If this row is pointed to by an active entry in the ACL tables, this object cannot be changed from active(1) to any other value. | 1.3.6.1.4.1.9.9.179.1.3.9.1.5 | RowStatus | read-create | current |
| caqSecurityAdjIndex OBJECT-TYPE Indicates the index of an active adjacency entry in caqAdjacencyTable. The value of this object is ignored whenever the value of caqSecurityAction object in the same row is not redirectWithAdj(4). | 1.3.6.1.4.1.9.9.179.1.3.9.1.6 | Unsigned32 (0..65535) | read-create | current |
| caqSecurityArpMacAddress OBJECT-TYPE Indicates the 48 bits Mac address used in ARP packet. The value of this object is ignored whenever the value of caqSecurityAction object in the same row is not one of the following values denyArpInspection(6), denyArpInspWithLog(7) and permitArpInspection(8). | 1.3.6.1.4.1.9.9.179.1.3.9.1.7 | MacAddress | read-create | current |
| caqSecurityRedirect2kPortList OBJECT-TYPE Indicates the set of physical port(s) that matched traffic is redirected to. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of redirect ports; the port is not included if its bit has a value of '0'. The value of this object is ignored whenever the value of caqSecurityAction object in the same row is not redirect(3). This object can accommodate up to 2048 ports. A port number is the value of dot1dBasePort for the port in the BRIDGE-MIB (RFC 1493). | 1.3.6.1.4.1.9.9.179.1.3.9.1.8 | OCTET STRING (SIZE(0..256)) | read-create | current |
| caqSecurityDownloadedAceFeature OBJECT-TYPE Indicates the feature type of the downloaded ACE. 'notApplicable' indicates that this security action entry is not applied to any downloaded ACE. 'dot1x' indicates that this security action entry is applied to downloaded ACE for 802.1x feature. 'macAuth' indicates that this security action entry is applied to downloaded ACE for Mac Authentication Bypass feature. 'webAuth' indicates that this security action entry is applied to downloaded ACE for Web-Proxy Authentication feature. 'eou' indicates that this security action entry is applied to downloaded ACE for Extensible Authentication Protocol over UDP (EOU) feature. 'ipPhone' indicates that this security action entry is applied to downloaded ACE for IP Phone feature. The value of this object is 'notApplicable' whenever the value of caqSecurityAction object in the same row is not 'include'. When an entry of this table is created with 'include' value specified for caqSecurityAction, 'notApplicable' cannot be used for this object value. | 1.3.6.1.4.1.9.9.179.1.3.9.1.9 | INTEGER {notApplicable(1), dot1x(2), macAuth(3), webAuth(4), eou(5), ipPhone(6)} | read-create | current |
| caqSecurityAclCaptureIfTable OBJECT-TYPE This table contains all the physical ports which are capable of being capture interfaces on which captured packets are output. | 1.3.6.1.4.1.9.9.179.1.3.10 | not-accessible | current | |
| caqSecurityAclCaptureIfEntry OBJECT-TYPE The index of this table is the ifIndex value of a physical port which is capable of being a capture interface on which captured packets are output. | 1.3.6.1.4.1.9.9.179.1.3.10.1 | not-accessible | current | |
| caqSecurityAclCaptureEnable OBJECT-TYPE An interface can be a destination of captured traffic which matched any Security ACL. This object is to specify whether to enable or disable this interface as a destination of captured traffic. | 1.3.6.1.4.1.9.9.179.1.3.10.1.1 | TruthValue | read-write | current |
| caqFlowPolicerExcessBurstSupport OBJECT-TYPE Indicates whether the device supports excess burst size configuration. | 1.3.6.1.4.1.9.9.179.1.3.11 | TruthValue | read-only | current |
| caqSecurityRateLimitFeatures OBJECT-TYPE Indicates the features which implement rate limit on their traffic flows using the rate limit value denoted by caqSecurityAclRateLimit object. This rate limit value is shared among all features denoted by this object. | 1.3.6.1.4.1.9.9.179.1.3.12 | Bits {arpInspection(0), dot1xDHCP(1), dhcpSnooping(2)} | read-only | current |
| caqSecurityAclRateLimit OBJECT-TYPE Indicates the maximum rate of all traffic flows subjected to rate limiting imposed by all features denoted by caqSecurityRateLimitFeatures object. | 1.3.6.1.4.1.9.9.179.1.3.13 | Unsigned32 | read-write | current |
| caqQosDefaultActionTable OBJECT-TYPE This table contains the QoS default action taken by the device for traffic which is not matched by a specific QoS ACE. | 1.3.6.1.4.1.9.9.179.1.3.14 | not-accessible | current | |
| caqQosDefaultActionEntry OBJECT-TYPE The entries in this table are corresponding to the type of traffic as well as its direction and contain the default DSCP value, trust state and policers information. The number of entry in this table depends on what type of traffic supported by the device. | 1.3.6.1.4.1.9.9.179.1.3.14.1 | not-accessible | current | |
| caqQosTrafficDirection OBJECT-TYPE Indicates whether this row's parameters are to be applied for ingress or for egress traffic. | 1.3.6.1.4.1.9.9.179.1.3.14.1.1 | CaqDirection | not-accessible | current |
| caqQosTrafficType OBJECT-TYPE Indicates whether this row's parameters are to be applied for Ethernet, IP or IPX traffic. | 1.3.6.1.4.1.9.9.179.1.3.14.1.2 | INTEGER {mac(1), ip(2), ipx(3)} | not-accessible | current |
| caqQosDefaultTrustState OBJECT-TYPE Indicates the default assigned trust state. If trustCos(2) is specified, the default DSCP value of an unmatched packet should refer to caqCosToDscpDscp object in caqCosToDscpTable to transfer layer 2 CoS value to DSCP value. If trustIpPrec(3) is specified, the default DSCP value of an unmatched packet should refer to caqIpPrecToDscpDscp object in caqIpPrecToDscpTable to transfer IP Precedence value to DSCP value. If trustDscp(4) is specified, the default DSCP value of an unmatched packet is the one which packets carry. If noTrust(1) is specified, the default DSCP value of an unmatched packet will have the value of caqQosDefaultDscp object. | 1.3.6.1.4.1.9.9.179.1.3.14.1.3 | INTEGER {noTrust(1), trustCos(2), trustIpPrec(3), trustDscp(4)} | read-write | current |
| caqQosDefaultDscp OBJECT-TYPE This object is only instantiated when the caqQosDefaultTrust object in the same entry has been set to noTrust(1). | 1.3.6.1.4.1.9.9.179.1.3.14.1.4 | Dscp | read-write | current |
| caqQosDefaultMicroflow OBJECT-TYPE Indicates a microflow policer name. The value of this object either matches the value of caqFlowPolicerName object of an active entry in caqFlowPolicerTable or has an empty string value. If there is no default microflow policer defined for unmatched traffic, this object should be an empty string. If the microflow(0) bit of caqFlowPolicingCpb object is turned off, this object should also be an empty string. Otherwise it should match the value of caqFlowPolicerName of an entry in the caqFlowPolicerTable which has its RowStatus value to be active(1) and the type of the policer should be microflow(1). | 1.3.6.1.4.1.9.9.179.1.3.14.1.5 | CaqPolicerNameOrEmpty | read-write | current |
| caqQosDefaultAggregate OBJECT-TYPE Indicates an aggregate policer name. The value of this object either matches the value of caqFlowPolicerName object of an active entry in caqFlowPolicerTable or has an empty string value. If there is no default aggregate policer defined for unmatched traffic, this object should be an empty string. If the aggregate(1) bit of caqFlowPolicingCpb object is turned off, this object should also be an an empty string. Otherwise it should match the value of caqFlowPolicerName of an entry in the caqFlowPolicerTable which has its RowStatus value to be active(1) and the type of the policer should be aggregate(2). | 1.3.6.1.4.1.9.9.179.1.3.14.1.6 | CaqPolicerNameOrEmpty | read-write | current |
| caqAclFeatureCpb OBJECT-TYPE Indicates the set of features that the device supports related to ACLs configured in the device. vlanAclHitCount(0) indicates that the device supports ACL hit count feature for ACLs attached to VLAN interfaces. portAclHitCount(1) indicates that the device supports ACL hit count feature for ACLs attached to physical interfaces. | 1.3.6.1.4.1.9.9.179.1.3.15 | Bits {vlanAclHitCount(0), portAclHitCount(1)} | read-only | current |
| caqQosStatsObjects OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.179.1.4 | |||
| caqL3PacketsDropByPolicer OBJECT-TYPE Indicates the number of Layer 3 packets dropped due to policing. | 1.3.6.1.4.1.9.9.179.1.4.1 | Counter64 | read-only | current |
| caqTosChangedIpPackets OBJECT-TYPE Indicates the number of IP packets have the Tos value changed. | 1.3.6.1.4.1.9.9.179.1.4.2 | Counter64 | read-only | current |
| caqCosChangedIpPackets OBJECT-TYPE Indicates the number of IP packets have the Cos value changed. | 1.3.6.1.4.1.9.9.179.1.4.3 | Counter64 | read-only | current |
| caqCosChangedNonIpPackets OBJECT-TYPE Indicates the number of non IP packets have the Cos value changed. | 1.3.6.1.4.1.9.9.179.1.4.4 | Counter64 | read-only | current |
| caqPortStatsTable OBJECT-TYPE A table containing QoS statistics counters per physical interface. | 1.3.6.1.4.1.9.9.179.1.4.5 | not-accessible | current | |
| caqPortStatsEntry OBJECT-TYPE An entry contains QoS statistics maintained by the switching engine. | 1.3.6.1.4.1.9.9.179.1.4.5.1 | not-accessible | current | |
| caqPortStatsDirection OBJECT-TYPE Indicates traffic direction of an physical interface. | 1.3.6.1.4.1.9.9.179.1.4.5.1.1 | CaqDirection | not-accessible | current |
| caqPortStatsQueueNumber OBJECT-TYPE Indicates the queue number of the interface for which statistics are collected. For example : if the port type of this interface is 1P2Q2T, this object can be 1, 2, 3. | 1.3.6.1.4.1.9.9.179.1.4.5.1.2 | CaqQueueNumber | not-accessible | current |
| caqPortStatsThresholdNumber OBJECT-TYPE Indicates the threshold number of a queue on the interface for which statistics are collected. For example : if the port type of this interface is 1P2Q2T, this object can be 1, 2. | 1.3.6.1.4.1.9.9.179.1.4.5.1.3 | CaqThresholdNumber | not-accessible | current |
| caqPortStatsDropPkts OBJECT-TYPE The number of packets have been received then dropped from the interface because they exceeded the threshold value configured at this queue and threshold of this interface. | 1.3.6.1.4.1.9.9.179.1.4.5.1.4 | Counter64 | read-only | current |
| caqPortStatsDropPktsAveRate OBJECT-TYPE The five minute linearly-decayed moving average of packets have been received then dropped from the interface because they exceeded the threshold value configured at this queue and threshold of this interface. | 1.3.6.1.4.1.9.9.179.1.4.5.1.5 | Gauge32 | read-only | current |
| caqPortStatsDropPktsPeakRate OBJECT-TYPE The peak rate of packets have been received then dropped from the interface because they exceeded the threshold value configured at this queue and threshold of this interface over the past five minutes. | 1.3.6.1.4.1.9.9.179.1.4.5.1.6 | Gauge32 | read-only | current |
| caqFlowStatsTable OBJECT-TYPE A table containing QoS statistics counter per flow. | 1.3.6.1.4.1.9.9.179.1.4.6 | not-accessible | current | |
| caqFlowStatsEntry OBJECT-TYPE An entry contains the number of out of profile packet per flow maintained by the switching engine. | 1.3.6.1.4.1.9.9.179.1.4.6.1 | not-accessible | current | |
| caqFlowStatsOutOfProfilePackets OBJECT-TYPE Indicates the number of out-of-profile packets in this flow. | 1.3.6.1.4.1.9.9.179.1.4.6.1.1 | Counter64 | read-only | current |
| caqAggPolicerStatsTable OBJECT-TYPE A table containing QoS statistics counter per aggregate policer. | 1.3.6.1.4.1.9.9.179.1.4.7 | not-accessible | current | |
| caqAggPolicerStatsEntry OBJECT-TYPE An entry contains the number of packet policed and the number of out of profile packets per aggregate policer. | 1.3.6.1.4.1.9.9.179.1.4.7.1 | not-accessible | current | |
| caqAggPolicerName OBJECT-TYPE The name of a policer. This name has to be unique to identify an aggregate policer in the device. | 1.3.6.1.4.1.9.9.179.1.4.7.1.1 | CaqPolicerName | not-accessible | current |
| caqAggPolicerPackets OBJECT-TYPE Indicates the number of packets is policed by this aggregate policer. This object is only instantiated if such info is available in the device. | 1.3.6.1.4.1.9.9.179.1.4.7.1.2 | Counter64 | read-only | current |
| caqAggPolicerNRExceedPackets OBJECT-TYPE Indicates the number of packets exceeded the normal rate of this aggregate policer. This object in only instantiated if such info is available in the device. | 1.3.6.1.4.1.9.9.179.1.4.7.1.3 | Counter64 | read-only | current |
| caqAggPolicerERExceedPackets OBJECT-TYPE Indicates the number of packets exceeded the excess rate of this policer. This object is only instantiated if such info is available in the device and if excess rate is supported by the device as indicated by caqFlowPolicerExcessRateSupport object. | 1.3.6.1.4.1.9.9.179.1.4.7.1.4 | Counter64 | read-only | current |
| caqAggPolicerOctets OBJECT-TYPE Indicates the number of octets is policed by this aggregate policer. This object is only instantiated if such info is available in the device. | 1.3.6.1.4.1.9.9.179.1.4.7.1.5 | Counter64 | read-only | current |
| caqAggPolicerNRExceedOctets OBJECT-TYPE Indicates the number of octets exceeded the normal rate of this aggregate policer. This object is only instantiated if such info is available in the device. | 1.3.6.1.4.1.9.9.179.1.4.7.1.6 | Counter64 | read-only | current |
| caqAggPolicerERExceedOctets OBJECT-TYPE Indicates the number of octets exceeded the excess rate of this policer. This object is only instantiated if such info is available in the device and if excess rate is supported by the device as indicated by caqFlowPolicerExcessRateSupport object. | 1.3.6.1.4.1.9.9.179.1.4.7.1.7 | Counter64 | read-only | current |
| caqAggPolicerOctetsRate OBJECT-TYPE Indicates five minute linearly-decayed moving average of octets policed by this aggregate policer. This object is only instantiated if such info is available in the device. | 1.3.6.1.4.1.9.9.179.1.4.7.1.8 | CounterBasedGauge64 | read-only | current |
| caqAggPolicerNRExceedOctetsRate OBJECT-TYPE Indicates five minute linearly-decayed moving average of octets exceeded the normal rate of this aggregate policer. This object is only instantiated if such info is available in the device. | 1.3.6.1.4.1.9.9.179.1.4.7.1.9 | CounterBasedGauge64 | read-only | current |
| caqAggPolicerERExceedOctetsRate OBJECT-TYPE Indicates five minute linearly-decayed moving average of octets exceeded the excess rate of this policer. This object is only instantiated if such info is available in the device and if excess rate is supported by the device as indicated by caqFlowPolicerExcessRateSupport object. | 1.3.6.1.4.1.9.9.179.1.4.7.1.10 | CounterBasedGauge64 | read-only | current |
| caqAggPolicerOctetsPeakRate OBJECT-TYPE Indicates peak rate of octets is policed by this aggregate policer over the past five minute. This object is only instantiated if such info is available in the device. | 1.3.6.1.4.1.9.9.179.1.4.7.1.11 | CounterBasedGauge64 | read-only | current |
| caqAggPolicerPacketsRate OBJECT-TYPE Indicates five minute linearly-decayed moving average of packets policed by this aggregate policer. This object is only instantiated if such info is available in the device. | 1.3.6.1.4.1.9.9.179.1.4.7.1.12 | CounterBasedGauge64 | read-only | current |
| caqAggPolicerNRExceedPacketsRate OBJECT-TYPE Indicates five minute linearly-decayed moving average of packets exceeded the normal rate of this aggregate policer. This object is only instantiated if such info is available in the device. | 1.3.6.1.4.1.9.9.179.1.4.7.1.13 | CounterBasedGauge64 | read-only | current |
| caqAggPolicerERExceedPacketsRate OBJECT-TYPE Indicates five minute linearly-decayed moving average of packets exceeded the excess rate of this policer. This object is only instantiated if such info is available in the device and if excess rate is supported by the device as indicated by caqFlowPolicerExcessRateSupport object. | 1.3.6.1.4.1.9.9.179.1.4.7.1.14 | CounterBasedGauge64 | read-only | current |
| caqAggPolicerPacketsPeakRate OBJECT-TYPE Indicates peak rate of packets is policed by this aggregate policer over the past five minutes. This object is only instantiated if such info is available in the device. | 1.3.6.1.4.1.9.9.179.1.4.7.1.15 | CounterBasedGauge64 | read-only | current |
| caqL3PacketsDropByPolicerAveRate OBJECT-TYPE Indicates five minute linearly-decayed moving average of Layer 3 packets dropped due to policing. | 1.3.6.1.4.1.9.9.179.1.4.8 | CounterBasedGauge64 | read-only | current |
| caqL3PacketsDropByPolicerPeakRate OBJECT-TYPE Indicates the peak rate of Layer 3 packets dropped due to policing over the past five minutes. | 1.3.6.1.4.1.9.9.179.1.4.9 | CounterBasedGauge64 | read-only | current |
| caqTosChangedIpPacketsAveRate OBJECT-TYPE Indicates five minute linearly-decayed moving average of IP packets have the Tos value change. | 1.3.6.1.4.1.9.9.179.1.4.10 | CounterBasedGauge64 | read-only | current |
| caqTosChangedIpPacketsPeakRate OBJECT-TYPE Indicates the peak rate of IP packets have the Tos value change over the past five minute. | 1.3.6.1.4.1.9.9.179.1.4.11 | CounterBasedGauge64 | read-only | current |
| caqCosChangedIpPacketsAveRate OBJECT-TYPE Indicates five minute linearly-decayed moving average of IP packets have the Cos value change. | 1.3.6.1.4.1.9.9.179.1.4.12 | CounterBasedGauge64 | read-only | current |
| caqCosChangedIpPacketsPeakRate OBJECT-TYPE Indicates the peak rate of IP packets have the Cos value change over the past five minutes. | 1.3.6.1.4.1.9.9.179.1.4.13 | CounterBasedGauge64 | read-only | current |
| caqCosChangedNonIpPacketsAveRate OBJECT-TYPE Indicates five minute linearly-decayed moving average of non IP packets have the Cos value change. | 1.3.6.1.4.1.9.9.179.1.4.14 | CounterBasedGauge64 | read-only | current |
| caqCosChangedNonIpPacketPeakRate OBJECT-TYPE Indicates the peak rate of non IP packets have the Cos value change over the past five minutes. | 1.3.6.1.4.1.9.9.179.1.4.15 | CounterBasedGauge64 | read-only | current |
| caqExtObjects OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.179.1.5 | |||
| caqBridgedPolicerTable OBJECT-TYPE This table provides configuration information for each (existing) VLAN on whether or not bridged packets are policed at the microflow level on that VLAN. This configuration is useful in situations in which there are insufficient resources to police bridged packets at the microflow level on all VLANs. This configuration has no effect on aggregate policing. | 1.3.6.1.4.1.9.9.179.1.5.1 | not-accessible | current | |
| caqBridgedPolicerEntry OBJECT-TYPE A conceptual row in the caqBridgedPolicerTable to control if bridged packets are policed at microflow level on a particular VLAN. | 1.3.6.1.4.1.9.9.179.1.5.1.1 | not-accessible | current | |
| caqBridgedFlowVlanIndex OBJECT-TYPE The VLAN-id of this VLAN. | 1.3.6.1.4.1.9.9.179.1.5.1.1.1 | VlanIndex | not-accessible | current |
| caqBridgedFlowEnabled OBJECT-TYPE Enable or Disable this function. If this objects is set to true, the bridged packets will be policed at microflow level. If it is set to false, bridged packets won't be policed at microflow level. This value has no effect on aggregate policing. The default is false. | 1.3.6.1.4.1.9.9.179.1.5.1.1.2 | TruthValue | read-write | current |
| caqCosMacVlanRouterTable OBJECT-TYPE This table is used either to assign a Cos value to frames on a specific VLAN and which have a specific destination MAC address and/or to indicate if the configured destination MAC address is of a router. This table is applied only for platform that supports these features. | 1.3.6.1.4.1.9.9.179.1.5.2 | not-accessible | current | |
| caqCosMacVlanRouterEntry OBJECT-TYPE The Cos value to be assigned to frames on a specific VLAN and which have a specific destination MAC address and/or the configured destination MAC address is of a router. | 1.3.6.1.4.1.9.9.179.1.5.2.1 | not-accessible | current | |
| caqCosMacAddress OBJECT-TYPE Indicates the destination MAC address to match against the flow. | 1.3.6.1.4.1.9.9.179.1.5.2.1.1 | MacAddress | not-accessible | current |
| caqCosVlanNumber OBJECT-TYPE Indicates the VLAN number. | 1.3.6.1.4.1.9.9.179.1.5.2.1.2 | VlanIndex | not-accessible | current |
| caqMacAddressCpb OBJECT-TYPE Indicates the capability of the destination MAC address denoted by caqCosMacAddress object in the same row. routerMac(0) means that it is a router Mac address. cosVlanMac(1) means that a Cos value is assigned to frames on a specific VLAN and which has this MAC address as its destination. | 1.3.6.1.4.1.9.9.179.1.5.2.1.3 | Bits {routerMac(0), cosVlanMac(1)} | read-create | current |
| caqCosValue OBJECT-TYPE Indicates the Cos value. This object is only instantiated if the cosVlanMac bit in caqMacAddressCpb object is turned on. | 1.3.6.1.4.1.9.9.179.1.5.2.1.4 | QosLayer2Cos | read-create | current |
| caqCosMacVlanRouterStatus OBJECT-TYPE The status of this conceptual row entry. This object is used to manage creation, deletion and modification of rows in this table. An entry may not exist in the active state unless all objects in the entry have an appropriate value. Once a row becomes active, value in any other column within such row cannot be modified except by setting caqCosMacVlanRouterStatus to notInService(2) for such row. | 1.3.6.1.4.1.9.9.179.1.5.2.1.5 | RowStatus | read-create | current |
| caqPbfObjects OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.179.1.6 | |||
| caqPbfStatus OBJECT-TYPE Indicates the status of policy-based forwarding (PBF) engine. macAddrOk(1) indicates that the MAC address of the PBF engine is set successfully and PBF engine is operational. macAddrNotSet(2) indicates that the MAC address of the PBF engine is not set and PBF engine is not operational. msfcPresent(3) indicates that there is a Multiplayer Switch Feature Card (MSFC) present in the device thus the PBF engine is not operational. | 1.3.6.1.4.1.9.9.179.1.6.1 | INTEGER {macAddrOk(1), macAddrNotSet(2), msfcPresent(3)} | read-only | current |
| caqPbfMacAddress OBJECT-TYPE Indicates the PBF engine MAC address. When the value of caqPbfStatus is msfcPresent(3), this object cannot be configured and its previously configured value is ignored. | 1.3.6.1.4.1.9.9.179.1.6.2 | MacAddress | read-write | current |
| caqAdjacencyTable OBJECT-TYPE This table contains a list of adjacencies to use in policy-based forwarding (PBF). PBF is a feature that makes possible forwarding between two different VLANs without having a router. | 1.3.6.1.4.1.9.9.179.1.6.3 | not-accessible | current | |
| caqAdjacencyEntry OBJECT-TYPE An entry defines an adjacency. Each adjacency consists of a destination VLAN, source and destination MAC address as well as adjacency name and MTU configuration. | 1.3.6.1.4.1.9.9.179.1.6.3.1 | not-accessible | current | |
| caqAdjIndex OBJECT-TYPE Indicates the index of this adjacency. | 1.3.6.1.4.1.9.9.179.1.6.3.1.1 | Unsigned32 (1..65535) | not-accessible | current |
| caqAdjDstVlanNumber OBJECT-TYPE Indicates the destination VLAN number of this adjacency. | 1.3.6.1.4.1.9.9.179.1.6.3.1.2 | VlanIndex | read-create | current |
| caqAdjDstMacAddress OBJECT-TYPE Indicates the adjacency destination MAC address. | 1.3.6.1.4.1.9.9.179.1.6.3.1.3 | MacAddress | read-create | current |
| caqAdjSrcMacAddress OBJECT-TYPE Indicates the adjacency source MAC address. If this object is not configured, it will contain the MAC address of the PBF engine which is denoted by caqPbfMacAddress object. | 1.3.6.1.4.1.9.9.179.1.6.3.1.4 | MacAddress | read-create | current |
| caqAdjName OBJECT-TYPE Indicates the adjacency name. The adjacency name should be unique among all entries in this table. | 1.3.6.1.4.1.9.9.179.1.6.3.1.5 | CaqAdjacencyName | read-create | current |
| caqAdjMtu OBJECT-TYPE Indicates the adjacency MTU. | 1.3.6.1.4.1.9.9.179.1.6.3.1.6 | Unsigned32 (576..18190) | read-create | current |
| caqAdjHitCount OBJECT-TYPE Indicates the number of packets that have matched this adjacency's criteria. The value of this object is cleared when this row is derefenced by entries in caqSecurityActionTable. | 1.3.6.1.4.1.9.9.179.1.6.3.1.7 | Counter64 | read-only | current |
| caqAdjStatus OBJECT-TYPE Indicates the status of this adjacency conceptual entry. This object is used to manage creation, deletion and modification of rows in this table. An entry may not exist in the active state unless all objects in the entry have an appropriate value. Once a row becomes active, value in any other column within such row cannot be modified. This object cannot be changed from active(1) to any other value if the following two conditions are met: - There is an active entry in caqSecurityActionTable with caqSecurityAdjIndex equal to caqAdjIndex. - That entry has caqSecurityAction set to redirectWithAdj(4). | 1.3.6.1.4.1.9.9.179.1.6.3.1.8 | RowStatus | read-create | current |
| caqLoggingObjects OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.179.1.7 | |||
| caqAclLogMaxFlow OBJECT-TYPE Indicates the maximum number of traffic flow will be logged by the device. | 1.3.6.1.4.1.9.9.179.1.7.1 | Unsigned32 (256..2048) | read-write | current |
| caqAclSecurityLoggingRateLimit OBJECT-TYPE Indicates the redirect rate of traffic flow subjected to security ACL logging. | 1.3.6.1.4.1.9.9.179.1.7.2 | Unsigned32 (500..5000) | read-write | current |
| caqAclRouterAclRateLimit OBJECT-TYPE Indicates the redirect rate of traffic flow subjected to router ACL logging. | 1.3.6.1.4.1.9.9.179.1.7.3 | Unsigned32 (1..1000) | read-write | current |
| caqIpFlowLoggingTable OBJECT-TYPE This table contains a list of IP flows that describes the IP traffic denied and logged by the device. | 1.3.6.1.4.1.9.9.179.1.7.4 | not-accessible | current | |
| caqIpFlowLoggingEntry OBJECT-TYPE An entry describes an IP flow, consisting of a set of data such as source and destination address, source and destination port as well as protocol specific information. To keep the table from overflow, each entry contains a TTL (Time to Live) object. An entry will be removed from this table when its TTL value reaches zero. | 1.3.6.1.4.1.9.9.179.1.7.4.1 | not-accessible | current | |
| caqIpFlowLoggingIndex OBJECT-TYPE The index of this table for indicating a logged IP flow. | 1.3.6.1.4.1.9.9.179.1.7.4.1.1 | Unsigned32 (1..65535) | not-accessible | current |
| caqIpFlowVlan OBJECT-TYPE Indicates the VLAN number which this logged IP flow belongs. | 1.3.6.1.4.1.9.9.179.1.7.4.1.2 | VlanIndex | read-only | current |
| caqIpFlowIfIndex OBJECT-TYPE Indicates the ifIndex of the interface where this logged IP flow arrived. | 1.3.6.1.4.1.9.9.179.1.7.4.1.3 | InterfaceIndex | read-only | current |
| caqIpFlowProtocolType OBJECT-TYPE The protocol number field in the IP header of this logged IP flow as specified in RFC 1700. | 1.3.6.1.4.1.9.9.179.1.7.4.1.4 | Unsigned32 (0..255) | read-only | current |
| caqIpFlowAddrType OBJECT-TYPE Indicates the address type for addresses specified in caqIpFlowSrcIp and caqIpFlowDestIp of this logged IP flow. | 1.3.6.1.4.1.9.9.179.1.7.4.1.5 | InetAddressType | read-only | current |
| caqIpFlowSrcIp OBJECT-TYPE Indicates the source address of this logged IP flow. | 1.3.6.1.4.1.9.9.179.1.7.4.1.6 | InetAddress | read-only | current |
| caqIpFlowSrcPort OBJECT-TYPE Indicates the source port number of this logged IP flow when its protocol field is TCP or UDP. The value of this object is -1 if the flow is not UDP or TCP traffic. | 1.3.6.1.4.1.9.9.179.1.7.4.1.7 | Integer32 (-1 | 0..65535) | read-only | current |
| caqIpFlowDestIp OBJECT-TYPE Indicates the destination address of this logged IP flow. | 1.3.6.1.4.1.9.9.179.1.7.4.1.8 | InetAddress | read-only | current |
| caqIpFlowDestPort OBJECT-TYPE Indicates the destination port number of this logged IP flow when its protocol field is TCP or UDP. The value of this object is -1 if the flow is not UDP or TCP traffic. | 1.3.6.1.4.1.9.9.179.1.7.4.1.9 | Integer32 (-1 | 0..65535) | read-only | current |
| caqIpFlowIcmpType OBJECT-TYPE Indicates the message type of ICMP packets. The value of this object is -1 if the flow is not ICMP traffic. | 1.3.6.1.4.1.9.9.179.1.7.4.1.10 | Integer32 (-1 | 0..255) | read-only | current |
| caqIpFlowIcmpCode OBJECT-TYPE Indicates the message code of ICMP packets. The value of this object is -1 if the flow is not ICMP traffic. | 1.3.6.1.4.1.9.9.179.1.7.4.1.11 | Integer32 (-1 | 0..255) | read-only | current |
| caqIpFlowIgmpType OBJECT-TYPE Indicates the message type of IGMP packets. The value of this object is -1 if the flow is not IGMP traffic. | 1.3.6.1.4.1.9.9.179.1.7.4.1.12 | Integer32 (-1 | 0..15) | read-only | current |
| caqIpFlowArpOpcode OBJECT-TYPE Indicates the ARP opcode value of this ARP flow. If the value of this object is notApplicable(1), this flow is not ARP traffic. If the value of this object is request(2), this flow is ARP request traffic. If the value of this object is reply(3), this flow is ARP reply traffic. | 1.3.6.1.4.1.9.9.179.1.7.4.1.13 | INTEGER {notApplicable(1), request(2), reply(3)} | read-only | current |
| caqIpFlowArpSrcMacAddr OBJECT-TYPE Indicates the Ethernet Source Address value of this ARP flow. This object is ignored if the flow is not ARP traffic. | 1.3.6.1.4.1.9.9.179.1.7.4.1.14 | MacAddress | read-only | current |
| caqIpFlowArpHeaderSrcMacAddr OBJECT-TYPE Indicates the Ethernet Source Address value included in the ARP header of this ARP flow. This object is ignored if the flow is not ARP traffic. | 1.3.6.1.4.1.9.9.179.1.7.4.1.15 | MacAddress | read-only | current |
| caqIpFlowPacketsCount OBJECT-TYPE Indicates the number of packets that belong to this IP flow. | 1.3.6.1.4.1.9.9.179.1.7.4.1.16 | Counter32 | read-only | current |
| caqIpFlowLoggingTTL OBJECT-TYPE Indicates the TTL (Time to Live) of this entry. The entry is removed when its value of this object reaches 0. | 1.3.6.1.4.1.9.9.179.1.7.4.1.17 | Unsigned32 | read-only | current |
| caqIpFlowArpLoggingSource OBJECT-TYPE Indicates the source that triggered the logging of this ARP flow. This object value is 'notApplicable' if the flow is not ARP traffic. 'dai' indicates the logging source is Dynamic Arp Inspection feature. 'acl' indicates the logging source is a configured security access control list (ACL). | 1.3.6.1.4.1.9.9.179.1.7.4.1.18 | INTEGER {notApplicable(1), dai(2), acl(3)} | read-only | current |
| caqIpFlowArpAclName OBJECT-TYPE Indicates the security ACL name which triggered the logging of this ARP flow. This object is ignored if the value of caqIpFlowArpLoggingSource object in the same row is not 'acl'. | 1.3.6.1.4.1.9.9.179.1.7.4.1.19 | SnmpAdminString | read-only | current |
| caqIpFlowArpAceNumber OBJECT-TYPE Indicates the ACE number within the ACL denoted by caqIpFlowArpAclName object which triggered the logging of this ARP flow. This object is ignored if the value of caqIpFlowArpLoggingSource object in the same row is not 'acl'. | 1.3.6.1.4.1.9.9.179.1.7.4.1.20 | Unsigned32 | read-only | current |
| caqArpInspObjects OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.179.1.8 | |||
| caqAclArpInspMatchMac OBJECT-TYPE Indicates whether for ARP packets MAC address matching of ethernet header and the source MAC address specified in ARP header is enabled. It also indicates the action taken when the addresses do not match. If this object value is disable(1), the device will not check for matching of source MAC address in ethernet header with the sender MAC address in ARP header for ARP packets. If this object value is enable(2), the device will check for matching of source MAC address in ethernet header with the sender MAC address in ARP header for ARP packets. A syslog message is generated if the MAC addresses check fails. If this object value is drop(3), the device will check for MAC addresses matching and ARP packets whose MAC addresses do not match will be dropped. If this object value is dropAndLog(4), the device will check for MAC addresses matching and ARP packets whose MAC addresses do not match will be dropped and logged into caqIpFlowLoggingTable. | 1.3.6.1.4.1.9.9.179.1.8.2 | INTEGER {disable(1), enable(2), drop(3), dropAndLog(4)} | read-write | current |
| caqAclArpInspAddrValidation OBJECT-TYPE Indicates whether for ARP packets checking for valid source MAC and source IP address specified in ARP header is enabled. It also indicates the action taken when the addresses are not valid. If this object value is disable(1), the device will not check for valid MAC and IP address for ARP packets. If this object value is enable(2), the device will check for valid MAC and IP address for ARP packets. A syslog message is generated if the addresses check fails. If this object value is drop(3), the device will check for valid MAC and IP addresses. ARP packets whose have illegal MAC and IP addresses will be dropped. If this object value is dropAndLog(4), the device will check for valid MAC and IP addresses. ARP packets whose have invalid MAC and IP addresses will be dropped and logged into caqIpFlowLoggingTable. | 1.3.6.1.4.1.9.9.179.1.8.3 | INTEGER {disable(1), enable(2), drop(3), dropAndLog(4)} | read-write | current |
| caqArpInspGlobalForwardedPkts OBJECT-TYPE Indicates the total number of packets subjected to ARP Inspection is forwarded. | 1.3.6.1.4.1.9.9.179.1.8.4 | Counter64 | read-only | current |
| caqArpInspGlobalDroppedPkts OBJECT-TYPE Indicates the total number of packets subjected to ARP Inspection is dropped. | 1.3.6.1.4.1.9.9.179.1.8.5 | Counter64 | read-only | current |
| caqRARPForwardedPkts OBJECT-TYPE Indicates the total number of packets subjected to Reverse ARP (RARP) Inspection is forwarded. | 1.3.6.1.4.1.9.9.179.1.8.6 | Counter64 | read-only | current |
| caqMatchedMacFailedPkts OBJECT-TYPE Indicates the total number of packets subjected to ARP Inspection whose MAC address specified in the ethernet header and the source MAC address specified in ARP header does not match. | 1.3.6.1.4.1.9.9.179.1.8.7 | Counter64 | read-only | current |
| caqAddrValidationFailedPkts OBJECT-TYPE Indicates the total number of ARP packets that have invalid source MAC address or invalid source IP address specified in the ARP header. | 1.3.6.1.4.1.9.9.179.1.8.8 | Counter64 | read-only | current |
| caqArpInspIpDroppedPkts OBJECT-TYPE Indicates the total number of IP packets dropped by ARP Inspection because of invalid IP address. | 1.3.6.1.4.1.9.9.179.1.8.9 | Counter64 | read-only | current |
| caqArpInspStatsTable OBJECT-TYPE A table containing ARP Inspection statistics counter per ACL. | 1.3.6.1.4.1.9.9.179.1.8.10 | not-accessible | current | |
| caqArpInspStatsEntry OBJECT-TYPE An entry contains the numbers of packet permitted or denied per ACL. | 1.3.6.1.4.1.9.9.179.1.8.10.1 | not-accessible | current | |
| caqArpInspAclName OBJECT-TYPE The name of an ACL that contains ACE used for ARP Inspection. | 1.3.6.1.4.1.9.9.179.1.8.10.1.1 | CaqAclName | not-accessible | current |
| caqArpInspForwardedPackets OBJECT-TYPE Indicates the number of packets subjected to ARP Inspection is forwarded by this ACL. | 1.3.6.1.4.1.9.9.179.1.8.10.1.2 | Counter64 | read-only | current |
| caqArpInspDroppedPackets OBJECT-TYPE Indicates the number of packets subjected to ARP Inspection is dropped by this ACL. | 1.3.6.1.4.1.9.9.179.1.8.10.1.3 | Counter64 | read-only | current |
| caqIfArpInspConfigTable OBJECT-TYPE This table contains the configuration of several threshold values related to ARP Inspection at each physical interface. | 1.3.6.1.4.1.9.9.179.1.8.11 | not-accessible | current | |
| caqIfArpInspConfigEntry OBJECT-TYPE Each entry contains the configuration for drop threshold and shutdown threshold for ARP Inspection at each physical interface that supports this feature. Some of the interfaces (but not limited to) for which this feature might be applicable are: ifType = ethernetCsmacd(6). | 1.3.6.1.4.1.9.9.179.1.8.11.1 | not-accessible | current | |
| caqIfArpInspDropThreshold OBJECT-TYPE Indicates the drop threshold value where excess packets of a traffic flow subjected to ARP Inspection will be dropped if its rate is greater than this threshold value. If the value of this object is 0, no rate limit is applied for dropping ARP traffic at this interface. | 1.3.6.1.4.1.9.9.179.1.8.11.1.1 | Unsigned32 (0..5000) | read-write | current |
| caqIfArpInspShutdownThreshold OBJECT-TYPE Indicates the threshold value where the interface will be shutdown if traffic rate subjected to ARP Inspection is greater than this threshold value. If the value of this object is 0, no ARP traffic rate limit is applied for shutting down the interface. | 1.3.6.1.4.1.9.9.179.1.8.11.1.2 | Unsigned32 (0..5000) | read-write | current |
| caqAclHitCountObjects OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.179.1.9 | |||
| caqAclHitCountVlansLow OBJECT-TYPE A string of octets containing one bit per VLAN for VLANs with VlanIndex value of 0 to 2047. The first octet corresponds to VLANs with VlanIndex values of 0 through 7; the second octet to VLANs 8 through 15; etc. The most significant bit of each octet corresponds to the lowest value VlanIndex in that octet. For each VLAN, if ACL hit count feature is enabled then the bit corresponding to that VLAN is set to '1'. Note that if the length of this string is less than 256 octets, any 'missing' octets are assumed to contain the value zero. A NMS may omit any zero-valued octets from the end of this string in order to reduce SetPDU size, and the agent may also omit zero-valued trailing octets, to reduce the size of GetResponse PDUs. This object is only instantiated when the vlanAclHitCount(0) bit is set to '1' in the caqAclFeatureCpb object. | 1.3.6.1.4.1.9.9.179.1.9.1 | OCTET STRING (SIZE(0..256)) | read-write | current |
| caqAclHitCountVlansHigh OBJECT-TYPE A string of octets containing one bit per VLAN for VLANs with VlanIndex value of 2048 to 4095. The first octet corresponds to VLANs with VlanIndex values of 2048 through 2055; the second octet to VLANs 2056 through 2063; etc. The most significant bit of each octet corresponds to the lowest value VlanIndex in that octet. For each VLAN, if ACL hit count feature is enabled then the bit corresponding to that VLAN is set to '1'. Note that if the length of this string is less than 256 octets, any 'missing' octets are assumed to contain the value zero. A NMS may omit any zero-valued octets from the end of this string in order to reduce SetPDU size, and the agent may also omit zero-valued trailing octets, to reduce the size of GetResponse PDUs. This object is only instantiated when the vlanAclHitCount(0) bit is set to '1' in the caqAclFeatureCpb object. | 1.3.6.1.4.1.9.9.179.1.9.2 | OCTET STRING (SIZE(0..256)) | read-write | current |
| caqAclHitCountPortList OBJECT-TYPE Indicates the set of physical port(s), in bridge port number, where ACL hit count feature is enabled. For each port, if ACL hit count feature is enabled then the bit corresponding to that port is set to '1'. This object is only instantiated when the portAclHitCount(1) bit is set to '1' in the caqAclFeatureCpb object. | 1.3.6.1.4.1.9.9.179.1.9.3 | CiscoPortList | read-write | current |
| caqAclHitCountTable OBJECT-TYPE This table provides the hit count configuration on ACLs which support this feature. | 1.3.6.1.4.1.9.9.179.1.9.4 | not-accessible | current | |
| caqAclHitCountEntry OBJECT-TYPE An entry indicates whether the hit count feature is enabled on a particular ACL as well as its statistic collection mode. | 1.3.6.1.4.1.9.9.179.1.9.4.1 | not-accessible | current | |
| caqAclHitCountAclType OBJECT-TYPE Indicates the type of ACL. ipSecurity(1) indicates that this ACL is an IP Security ACL. ipxSecurity(2) indicates that this ACL is an IPX Security ACL. macSecurity(3) indicates that this ACL is a MAC Security ACL. | 1.3.6.1.4.1.9.9.179.1.9.4.1.1 | CaqHitCountAclType | not-accessible | current |
| caqAclHitCountAclName OBJECT-TYPE Indicates the ACL name which should exist in the ACL tables e.g. in caqIpAceTable. This ACL must be matching the type specified in caqAclHitCountAclType in the same row. | 1.3.6.1.4.1.9.9.179.1.9.4.1.2 | CaqAclName | not-accessible | current |
| caqAclHitCountEnable OBJECT-TYPE Indicates whether this ACL hit count is enabled. | 1.3.6.1.4.1.9.9.179.1.9.4.1.3 | TruthValue | read-write | current |
| caqAceHitCountTable OBJECT-TYPE This table provides the hit count configuration on ACEs which support this feature. | 1.3.6.1.4.1.9.9.179.1.9.5 | not-accessible | current | |
| caqAceHitCountEntry OBJECT-TYPE An entry indicates whether the hit count feature is enabled on a particular ACE as well as its hit count statistic. | 1.3.6.1.4.1.9.9.179.1.9.5.1 | not-accessible | current | |
| caqAceHitCountAclType OBJECT-TYPE Indicates the type of ACL. ipSecurity(1) indicates that this ACL is an IP Security ACL. ipxSecurity(2) indicates that this ACL is an IPX Security ACL. macSecurity(3) indicates that this ACL is a MAC Security ACL. | 1.3.6.1.4.1.9.9.179.1.9.5.1.1 | CaqHitCountAclType | not-accessible | current |
| caqAceHitCountAclName OBJECT-TYPE Indicates the ACL name which should exist in the ACL tables e.g. in caqIpAceTable. This ACL must be matching the type specified in caqAceHitCountAclType in the same row. | 1.3.6.1.4.1.9.9.179.1.9.5.1.2 | CaqAclName | not-accessible | current |
| caqAceHitCountAceIndex OBJECT-TYPE The index of an ACE within an ACL. | 1.3.6.1.4.1.9.9.179.1.9.5.1.3 | Unsigned32 (1..65535) | not-accessible | current |
| caqAceHitCountEnable OBJECT-TYPE Indicates whether this ACE hit count is enabled. | 1.3.6.1.4.1.9.9.179.1.9.5.1.4 | TruthValue | read-write | current |
| caqAceIngressHitCount OBJECT-TYPE Indicates number of hit count for this ACE for ingress traffic. | 1.3.6.1.4.1.9.9.179.1.9.5.1.5 | Counter64 | read-only | current |
| caqAceEgressHitCount OBJECT-TYPE Indicates number of hit count for this ACE for egress traffic. | 1.3.6.1.4.1.9.9.179.1.9.5.1.6 | Counter64 | read-only | current |
| caqIfAclHitCountTable OBJECT-TYPE This table provides the ACL hit count statistics at an interface. An interface can be a physical port if the bit portAclHitCount(1) is set in the object caqAclFeatureCpb or a VLAN if the bit vlanAclHitCount(0) is set in the object caqAclFeatureCpb. | 1.3.6.1.4.1.9.9.179.1.9.6 | not-accessible | current | |
| caqIfAclHitCountEntry OBJECT-TYPE Each entry indicates the number of hit count at each ACE belonged to an ACL which supports hit count collection at an interface where the ACL is attached. | 1.3.6.1.4.1.9.9.179.1.9.6.1 | not-accessible | current | |
| caqIfAclHitCountAclType OBJECT-TYPE Indicates the type of ACL. ipSecurity(1) indicates that this ACL is an IP Security ACL. ipxSecurity(2) indicates that this ACL is an IPX Security ACL. macSecurity(3) indicates that this ACL is a MAC Security ACL. | 1.3.6.1.4.1.9.9.179.1.9.6.1.1 | CaqHitCountAclType | not-accessible | current |
| caqIfAclHitCountAclName OBJECT-TYPE Indicates the ACL name which should exist in the ACL tables e.g. in caqIpAceTable. This ACL must be matching the type specified in caqIfAclHitCountAclType in the same row. | 1.3.6.1.4.1.9.9.179.1.9.6.1.2 | CaqAclName | not-accessible | current |
| caqIfAclHitCountAceIndex OBJECT-TYPE The index of an ACE within an ACL. | 1.3.6.1.4.1.9.9.179.1.9.6.1.3 | Unsigned32 (1..65535) | not-accessible | current |
| caqIfAclIngressHitCount OBJECT-TYPE Indicates the number of hit count of this ACE for ingress traffic on this interface. | 1.3.6.1.4.1.9.9.179.1.9.6.1.4 | Counter64 | read-only | current |
| caqIfAclEgressHitCount OBJECT-TYPE Indicates the number of hit count of this ACE for egress traffic on this interface. | 1.3.6.1.4.1.9.9.179.1.9.6.1.5 | Counter64 | read-only | current |
| caqDownloadAclObjects OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.179.1.10 | |||
| caqDownloadAclInfoTable OBJECT-TYPE This table provides the management information for downloaded ACLs. | 1.3.6.1.4.1.9.9.179.1.10.1 | not-accessible | current | |
| caqDownloadAclInfoEntry OBJECT-TYPE An entry is populated for each downloaded ACL in the device. | 1.3.6.1.4.1.9.9.179.1.10.1.1 | not-accessible | current | |
| caqDownloadAclName OBJECT-TYPE This object indicates the name of a downloaded ACL. | 1.3.6.1.4.1.9.9.179.1.10.1.1.1 | SnmpAdminString (SIZE(1..255)) | not-accessible | current |
| caqDownloadAclUserCount OBJECT-TYPE This object indicates the number of users (i.e., authenticated hosts) who are using this downloaded ACL. | 1.3.6.1.4.1.9.9.179.1.10.1.1.2 | Unsigned32 | read-only | current |
| caqDownloadAclDownloadTime OBJECT-TYPE This object indicates the time when this ACL is downloaded to the device. | 1.3.6.1.4.1.9.9.179.1.10.1.1.3 | DateAndTime | read-only | current |
| caqIpDownloadAceTable OBJECT-TYPE This table contains a list of downloaded IP ACEs for security purpose. Each ACE consists of a filter specification and behavior associated with it which describes what action to carry out on packets which match. An ACL is defined as the set of ACEs. Each ACE is named by a combination of an AclName and an ACE index, such that all the ACEs which are named using the same AclName are part of the same ACL. | 1.3.6.1.4.1.9.9.179.1.10.2 | not-accessible | current | |
| caqIpDownloadAceEntry OBJECT-TYPE An entry defines an ACE, consisting of a set of match criteria. For a packet to match an entry, it has to match all the criteria specified in that entry. | 1.3.6.1.4.1.9.9.179.1.10.2.1 | not-accessible | current | |
| caqIpDownloadAclName OBJECT-TYPE The name of a downloaded IP ACL. | 1.3.6.1.4.1.9.9.179.1.10.2.1.1 | SnmpAdminString | not-accessible | current |
| caqIpDownloadAceIndex OBJECT-TYPE The index of an ACE within a downloaded ACL. | 1.3.6.1.4.1.9.9.179.1.10.2.1.2 | Unsigned32 | not-accessible | current |
| caqIpDownloadAceMatchedAction OBJECT-TYPE Indicates the action to be taken if a packet matches this ACE. If 'permit' is specified, the matched packet will be allowed through the device. If 'deny' is specified, the matched packet will be blocked and dropped. If 'denyAndLog' is specified, the matched packet will be blocked, dropped and logged. If 'permitAndCapture' is specified, the matched packet will be allowed, and a copy of it will be forwarded to capture port(s). | 1.3.6.1.4.1.9.9.179.1.10.2.1.3 | INTEGER {permit(1), deny(2), denyAndLog(3), permitAndCapture(4)} | read-only | current |
| caqIpDownloadAceProtocolType OBJECT-TYPE The protocol number field in the IP header used to indicate the higher layer protocol as specified in RFC 1700. A value value of 0 matches every IP packet. For example : 0 is IP, 1 is ICMP, 2 is IGMP, 4 is IP in IP encapsulation, 6 is TCP, 9 is IGRP, 17 is UDP, 47 is GRE, 50 is ESP, 51 is AH, 88 is IGRP, 89 is OSPF, 94 is KA9Q/NOS compatible IP over IP, 103 is PIMv2, 108 is PCP. | 1.3.6.1.4.1.9.9.179.1.10.2.1.4 | CiscoIpProtocol | read-only | current |
| caqIpDownloadAceAddrType OBJECT-TYPE The type of IP address used by this ACE entry. | 1.3.6.1.4.1.9.9.179.1.10.2.1.5 | InetAddressType | read-only | current |
| caqIpDownloadAceSrcIp OBJECT-TYPE The specified source IP address. The packet's source address is AND-ed with the value of caqIpDownloadAceSrcIpMask and then compared against the value of this object. If this object value is 0.0.0.0, and the value of caqIpDownloadAceSrcIpMask object in the same entry is 255.255.255.255, this entry matches any source IP address. | 1.3.6.1.4.1.9.9.179.1.10.2.1.6 | InetAddress | read-only | current |
| caqIpDownloadAceSrcIpMask OBJECT-TYPE The specified source IP address mask. | 1.3.6.1.4.1.9.9.179.1.10.2.1.7 | InetAddress | read-only | current |
| caqIpDownloadAceSrcPortOp OBJECT-TYPE Indicates how a packet's source TCP/UDP port number is to be compared. 'noOperator', which is the default value, means that no comparison is to be made with the source TCP/UDP port number. 'lt' means less than, 'gt' means greater than, 'eq' means equal, 'neq' means not equal. Those 4 operators are using the caqIpDownloadAceSrcPort object as an operand which is the only one needed. 'range' means that it compares the port value between two numbers, so this operator needs 2 operands. One operand is the starting port number of the range which is caqIpDownloadAceSrcPort object, and the other operand is the ending port number of the range which the caqIpDownloadAceSrcPortRange object is in. | 1.3.6.1.4.1.9.9.179.1.10.2.1.8 | INTEGER {noOperator(1), lt(2), gt(3), eq(4), neq(5), range(6)} | read-only | current |
| caqIpDownloadAceSrcPort OBJECT-TYPE The source port number of the TCP or UDP protocol. If the caqIpDownloadAceSrcPortOp object in the same row is 'range', this object will be the starting port number of the port range. | 1.3.6.1.4.1.9.9.179.1.10.2.1.9 | InetPortNumber | read-only | current |
| caqIpDownloadAceSrcPortRange OBJECT-TYPE The source port number of the TCP or UDP protocol. If the caqIpDownloadAceSrcPortOp object in the same row is 'range', this object will be the ending port number of the port range, otherwise the value of this object is ignored. | 1.3.6.1.4.1.9.9.179.1.10.2.1.10 | InetPortNumber | read-only | current |
| caqIpDownloadAceDestIp OBJECT-TYPE The specified destination IP address. The packet's destination address is AND-ed with the value of caqIpDownloadAceDestIpMask and then compared against the value of this object. If this object value is 0.0.0.0 and the value of caqIpDownloadAceDestIpMask object in the same entry is 255.255.255.255, this entry matches any destination IP address. | 1.3.6.1.4.1.9.9.179.1.10.2.1.11 | InetAddress | read-only | current |
| caqIpDownloadAceDestIpMask OBJECT-TYPE The specified destination IP address mask. | 1.3.6.1.4.1.9.9.179.1.10.2.1.12 | InetAddress | read-only | current |
| caqIpDownloadAceDestPortOp OBJECT-TYPE Indicates how a packet's destination TCP/UDP port number is to be compared. 'noOperator', which is the default value, means that no comparison is to be made with the destination TCP/UDP port number. 'lt' means less than. 'gt' means greater than. 'eq' means equal. 'neq' means not equal. Those 4 operators are using the caqIpDownloadAceDestPort object as an operand which is the only one needed. 'range' means that it compares the port value between two numbers, so this operator needs 2 operands. One operand is the starting port number of the range which is caqIpDownloadAceDestPort object, and the other operand is the ending port number of the range which the caqIpDownloadAceDestPortRange object is in. | 1.3.6.1.4.1.9.9.179.1.10.2.1.13 | INTEGER {noOperator(1), lt(2), gt(3), eq(4), neq(5), range(6)} | read-only | current |
| caqIpDownloadAceDestPort OBJECT-TYPE The destination port number of the TCP or UDP protocol. If the caqIpDownloadAceDestPortOp object in the same row is 'range' this object will be the starting port number of the port range. | 1.3.6.1.4.1.9.9.179.1.10.2.1.14 | InetPortNumber | read-only | current |
| caqIpDownloadAceDestPortRange OBJECT-TYPE The destination port number of the TCP or UDP protocol. If the caqIpDownloadAceDestPortOp object in the same row is 'range', this object will be the ending port number of the port range, otherwise this object value is ignored. | 1.3.6.1.4.1.9.9.179.1.10.2.1.15 | InetPortNumber | read-only | current |
| caqIpDownloadAceTosMatchCriteria OBJECT-TYPE Indicates what field of Tos octet in the packet header to be matched. 'none' means that there is no need to match the ToS octet. 'matchDscp' means that the DSCP value of packet header need to be matched. If this value is specified, the caqIpDownloadAceDscp object in the same row should have valid value. 'matchIpPrec' means that the IpPrecedence value of packet header need to be matched. If this value is specifed, the caqIpDownloadAceIpPrec object in the same row should have a valid value. | 1.3.6.1.4.1.9.9.179.1.10.2.1.16 | INTEGER {none(1), matchDscp(2), matchIpPrec(3)} | read-only | current |
| caqIpDownloadAceIpPrec OBJECT-TYPE Specifies the IP precedence value to be matched against. The value of this object is ignored whenever the value of caqIpDownloadAceTosMatchCritial object is not 'matchIpPrec'. | 1.3.6.1.4.1.9.9.179.1.10.2.1.17 | CaqIpPrecedence | read-only | current |
| caqIpDownloadAceDscp OBJECT-TYPE Specifies the Dscp value to be matched against. Packets can be matched to DSCP value from 0 to 63. The value of this object is ignored whenever the value of caqIpDownloadAceTosMatchCritial object is not 'matchDscp'. | 1.3.6.1.4.1.9.9.179.1.10.2.1.18 | Dscp | read-only | current |
| caqIpDnldAcePrtocolMatchCriteria OBJECT-TYPE Indicates what field in the packet header for ICMP or IGMP or TCP protocol to be matched. 'none' means no comparison is to be done for ICMP/TCP. 'matchIcmpType' means that the Type field of ICMP protocol packet header needs to be matched. If this value is specified, the caqIpDownloadAceIcmpType object in the same row should have a valid value. 'matchIcmpTypeAndCode' means that both the Type and Code fields of ICMP protocol packet header need to be matched. If this value is specified, the caqIpDownloadAceIcmpType and caqIpDownloadAceIcmpCode object in the same row should have valid values. 'matchEstablished' means that a match occurs if the TCP packet has the ACK or RST bits set. The non matching case is that of the intial TCP packet to form a connection. | 1.3.6.1.4.1.9.9.179.1.10.2.1.19 | INTEGER {none(1), matchIcmpType(2), matchIcmpTypeAndCode(3), matchEstablished(4)} | read-only | current |
| caqIpDownloadAceIcmpType OBJECT-TYPE Indicates the message type of ICMP packets. The type is a number from 0 to 255. The value of this object is ignored whenever the value of caqIpDnldAcePrtocolMatchCriteria object is not 'matchIcmpType' or 'matchIcmpTypeAndCode'. | 1.3.6.1.4.1.9.9.179.1.10.2.1.20 | Unsigned32 | read-only | current |
| caqIpDownloadAceIcmpCode OBJECT-TYPE Indicates the message code of ICMP packets. The code is a number from 0 to 255. The value of this object is ignored whenever the value of caqIpDnldAcePrtocolMatchCriteria object is not 'matchIcmpTypeAndCode'. | 1.3.6.1.4.1.9.9.179.1.10.2.1.21 | Unsigned32 | read-only | current |
| caqIfDownloadAclTable OBJECT-TYPE This table provides the management information for physical interface where downloaded ACLs are applied. | 1.3.6.1.4.1.9.9.179.1.10.3 | not-accessible | current | |
| caqIfDownloadAclEntry OBJECT-TYPE An entry is populated for each interface that utilies downloaded ACLs in the device. | 1.3.6.1.4.1.9.9.179.1.10.3.1 | not-accessible | current | |
| caqIfDownloadAclFeature OBJECT-TYPE This object indicates the security feature running at this interface and trigger the download of this ACL. 'dot1x' indicates that the 802.1x feature is running at this interface and trigger the download of this ACL. 'eou' indicates that the Extensible Authentication Protocol over UDP (EOU) feature is running at this interface and trigger the download of this ACL. 'macAuth' indicates that the Mac Authentication Bypass feature is running at this interface and trigger the download of this ACL. 'webAuth' indicates that the Web Authentication feature is running at this interface and trigger the download of this ACL. | 1.3.6.1.4.1.9.9.179.1.10.3.1.1 | INTEGER {dot1x(1), eou(2), macAuth(3), webAuth(4)} | read-only | current |
| caqIfDownloadAclAddressType OBJECT-TYPE This object indicates the type of IP address of the host. | 1.3.6.1.4.1.9.9.179.1.10.3.1.2 | InetAddressType | read-only | current |
| caqIfDownloadAclHostAddress OBJECT-TYPE This object indicates IP address of the host connected to this interface. The type of this address is determined by the value of caqIfDownloadAclAddressType object. | 1.3.6.1.4.1.9.9.179.1.10.3.1.3 | InetAddress | read-only | current |
| caqIfIpPhoneMapTable OBJECT-TYPE This table provides the management information for the mapping of IP Phone to interface that utilizes downloaded ACL. | 1.3.6.1.4.1.9.9.179.1.10.4 | not-accessible | current | |
| caqIfIpPhoneMapEntry OBJECT-TYPE An entry is populated for each interface that has an IP Phone connected to and utilizes downloaded ACL. | 1.3.6.1.4.1.9.9.179.1.10.4.1 | not-accessible | current | |
| caqIfIpPhoneAddressType OBJECT-TYPE This object indicates the type of IP address of the IP Phone connected to this interface. | 1.3.6.1.4.1.9.9.179.1.10.4.1.1 | InetAddressType | read-only | current |
| caqIfIpPhoneHostAddress OBJECT-TYPE This object indicates the IP address of the IP Phone. The type of this address is determined by the value of the caqIfIpPhoneAddressType object. | 1.3.6.1.4.1.9.9.179.1.10.4.1.2 | InetAddress | read-only | current |
| caqMIBNotifications OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.179.2 | |||
| caqMIBConformance OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.179.3 | |||
| caqMIBCompliances OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.179.3.1 | |||
| caqMIBGroups OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.179.3.2 |
Conformance
| Name | OID | Status |
|---|---|---|
| caqMIBCompliance MODULE-COMPLIANCE The compliance statement for the CISCO-CATOS-ACL-QOS-MIB. | 1.3.6.1.4.1.9.9.179.3.1.1 | deprecated |
| caqMIBCompliance2 MODULE-COMPLIANCE The compliance statement for the CISCO-CATOS-ACL-QOS-MIB. | 1.3.6.1.4.1.9.9.179.3.1.2 | deprecated |
| caqMIBCompliance3 MODULE-COMPLIANCE The compliance statement for the CISCO-CATOS-ACL-QOS-MIB. | 1.3.6.1.4.1.9.9.179.3.1.3 | deprecated |
| caqMIBCompliance4 MODULE-COMPLIANCE The compliance statement for the CISCO-CATOS-ACL-QOS-MIB. | 1.3.6.1.4.1.9.9.179.3.1.4 | current |
| caqIfConfigGroup OBJECT-GROUP A collection of objects providing the Qos configuration information at each physical interface on the device. | 1.3.6.1.4.1.9.9.179.3.2.1 | current |
| caqIfAclConfigGroup OBJECT-GROUP A collection of objects providing the ACL information on the device. | 1.3.6.1.4.1.9.9.179.3.2.2 | current |
| caqAclCpbGroup OBJECT-GROUP A collection of objects providing the ACL information on the device. | 1.3.6.1.4.1.9.9.179.3.2.3 | current |
| caqIpAceGroup OBJECT-GROUP A collection of objects providing the IP ACE information. | 1.3.6.1.4.1.9.9.179.3.2.4 | current |
| caqIpxAceGroup OBJECT-GROUP A collection of objects providing the IPX ACE information. | 1.3.6.1.4.1.9.9.179.3.2.5 | current |
| caqMacAceGroup OBJECT-GROUP A collection of objects providing the MAC ACE information. | 1.3.6.1.4.1.9.9.179.3.2.6 | current |
| caqActionGroup OBJECT-GROUP A collection of objects providing the ACE action information. | 1.3.6.1.4.1.9.9.179.3.2.7 | current |
| caqPolicingGroup OBJECT-GROUP A collection of objects providing the microflow and aggregate flow configuration. | 1.3.6.1.4.1.9.9.179.3.2.8 | current |
| caqQosExcessRateGroup OBJECT-GROUP A collection of objects providing Qos information on excess rate. | 1.3.6.1.4.1.9.9.179.3.2.9 | current |
| caqQosMappingGroup OBJECT-GROUP A collection of objects providing Qos mapping information. | 1.3.6.1.4.1.9.9.179.3.2.10 | current |
| caqQueueAssignmentGroup OBJECT-GROUP A collection of objects providing the queue assignment information. | 1.3.6.1.4.1.9.9.179.3.2.11 | current |
| caqQueueGroup OBJECT-GROUP A collection of objects providing the queue information. | 1.3.6.1.4.1.9.9.179.3.2.12 | current |
| caqQosBridgedFlowPolicerGroup OBJECT-GROUP A collection of objects providing the information on bridged packet policing. | 1.3.6.1.4.1.9.9.179.3.2.13 | current |
| caqQosMacVlanGroup OBJECT-GROUP A collection of objects providing the classification information based on Mac address and vlan. | 1.3.6.1.4.1.9.9.179.3.2.14 | current |
| caqQosStatsGroup OBJECT-GROUP A collection of objects providing the QoS statistics information. | 1.3.6.1.4.1.9.9.179.3.2.15 | current |
| caqSecurityGroup OBJECT-GROUP A collection of objects providing the security information. | 1.3.6.1.4.1.9.9.179.3.2.16 | deprecated |
| caqFlowPolicingCpbGroup OBJECT-GROUP A collection of object providing the flow policing capability information. | 1.3.6.1.4.1.9.9.179.3.2.17 | current |
| caqQosStatsGroup2 OBJECT-GROUP A collection of objects providing the QoS statistics information per aggregate policer. | 1.3.6.1.4.1.9.9.179.3.2.18 | current |
| caqSecurityPBFGroup OBJECT-GROUP A collection of objects providing the PBF configuration and statistics information. | 1.3.6.1.4.1.9.9.179.3.2.19 | current |
| caqQosExcessBurstGroup OBJECT-GROUP A collection of objects providing Qos information on excess burst size. | 1.3.6.1.4.1.9.9.179.3.2.20 | current |
| caqIfTrustDeviceGroup OBJECT-GROUP A collection of objects providing the trusted device configuration and operational state. | 1.3.6.1.4.1.9.9.179.3.2.21 | current |
| caqLoggingGroup OBJECT-GROUP A collection of objects providing the security logging configuration and statistics. | 1.3.6.1.4.1.9.9.179.3.2.22 | current |
| caqArpInspGroup OBJECT-GROUP A collection of objects providing the ARP Inspection configuration and statistics. | 1.3.6.1.4.1.9.9.179.3.2.23 | current |
| caqSecurityRateLimitGroup OBJECT-GROUP A collection of objects providing the security acl feature rate limit configuration state. | 1.3.6.1.4.1.9.9.179.3.2.24 | current |
| caqDscpMutationGroup OBJECT-GROUP A collection of objects providing the DSCP mutation configuration information. | 1.3.6.1.4.1.9.9.179.3.2.25 | current |
| caqQosDefaultActionGroup OBJECT-GROUP A collection of objects providing the default Qos action configuration on the device. | 1.3.6.1.4.1.9.9.179.3.2.26 | current |
| caqIfAclConfigGroup2 OBJECT-GROUP A collection of object providing the additional ACL attachment configuration on the device. | 1.3.6.1.4.1.9.9.179.3.2.27 | current |
| caqIpEspGroup OBJECT-GROUP A collection of object providing the Ip ESP traffic matching configuration on the device. | 1.3.6.1.4.1.9.9.179.3.2.28 | current |
| caqDscpRewriteGroup OBJECT-GROUP A collection of object providing the configuration of DSCP rewrite feature on the device. | 1.3.6.1.4.1.9.9.179.3.2.29 | current |
| caqAggPolicerOctetStatsGroup OBJECT-GROUP A collection of objects providing the QoS statistics information per aggregate policer in unit of octet. | 1.3.6.1.4.1.9.9.179.3.2.30 | current |
| caqSecurityGroup2 OBJECT-GROUP A collection of objects providing the security information. | 1.3.6.1.4.1.9.9.179.3.2.31 | current |
| caqIfSecurityAclConfigGroup OBJECT-GROUP A collection of objects providing the security ACL information on the device. | 1.3.6.1.4.1.9.9.179.3.2.32 | current |
| caqIpAceExtGroup OBJECT-GROUP A collection of objects providing the source and destination group information to configure IP ACL on the device. | 1.3.6.1.4.1.9.9.179.3.2.33 | current |
| caqAclHitCountGroup OBJECT-GROUP A collection of objects providing the ACL hit count configuration and statistics on the device. | 1.3.6.1.4.1.9.9.179.3.2.34 | current |
| caqMacAceExtGroup OBJECT-GROUP A collection of objects providing addtional matching criteria such as the VLAN, Cos information to configure MAC ACE on the device. | 1.3.6.1.4.1.9.9.179.3.2.35 | current |
| caqMacPktClassifyVlanGroup OBJECT-GROUP A collection of objects providing the VLAN configuration for MAC packet classify feature on the device. | 1.3.6.1.4.1.9.9.179.3.2.36 | current |
| caqAclFeatureGroup OBJECT-GROUP A collection of object providing what feature related to ACL that the device is capable of. | 1.3.6.1.4.1.9.9.179.3.2.37 | current |
| caqPortAclHitCountGroup OBJECT-GROUP A collection of object providing the set of physical ports where ACL hit count feature is enabled. | 1.3.6.1.4.1.9.9.179.3.2.38 | current |
| caqVlanAclHitCountGroup OBJECT-GROUP A collection of objects providing the set of VLANs where ACL hit count feature is enabled. | 1.3.6.1.4.1.9.9.179.3.2.39 | current |
| caqQosL3StatsRateGroup OBJECT-GROUP A collection of objects providing the five minute linearly-decayed moving average QoS statistics for Layer 3 traffic. | 1.3.6.1.4.1.9.9.179.3.2.40 | current |
| caqQosL3StatsPeakGroup OBJECT-GROUP A collection of objects providing the peak rate QoS statistics over past five minute period for Layer 3 traffic. | 1.3.6.1.4.1.9.9.179.3.2.41 | current |
| caqAggPolicerOctetsRateGroup OBJECT-GROUP A collection of objects providing the five minute linearly-decayed octets moving average rate per aggregate policer. | 1.3.6.1.4.1.9.9.179.3.2.42 | current |
| caqAggPolicerPacketsRateGroup OBJECT-GROUP A collection of objects providing the five minute linearly-decayed packets moving average rate per aggregate policer. | 1.3.6.1.4.1.9.9.179.3.2.43 | current |
| caqAggPolicerOctetsPeakGroup OBJECT-GROUP A collection of objects providing the peak rate of octets over past five minute period per aggregate policer. | 1.3.6.1.4.1.9.9.179.3.2.44 | current |
| caqAggPolicerPacketsPeakGroup OBJECT-GROUP A collection of objects providing the peak rate of packets over past five minute period per aggregate policer. | 1.3.6.1.4.1.9.9.179.3.2.45 | current |
| caqQosPortRateGroup OBJECT-GROUP A collection of object providing the five minute linearly-decayed packets drop rate per interface. | 1.3.6.1.4.1.9.9.179.3.2.46 | current |
| caqQosPortPeakGroup OBJECT-GROUP A collection of object providing the peak rate of packets over past five minute period per interface. | 1.3.6.1.4.1.9.9.179.3.2.47 | current |
| caqSecurityActionDnldAceGroup OBJECT-GROUP A collection of object providing feature type of downloaded ACE. | 1.3.6.1.4.1.9.9.179.3.2.48 | current |
| caqSecurityDownloadAclInfoGroup OBJECT-GROUP A collection of object providing downloaded ACL information. | 1.3.6.1.4.1.9.9.179.3.2.49 | current |
| caqSecurityDownloadIpAceGroup OBJECT-GROUP A collection of object providing download IP ACE information. | 1.3.6.1.4.1.9.9.179.3.2.50 | current |
| caqIfDownloadAclMapGroup OBJECT-GROUP A collection of object providing mapping information of downloaded ACL to capable interface. | 1.3.6.1.4.1.9.9.179.3.2.51 | current |
| caqIfIpPhoneMapGroup OBJECT-GROUP A collection of object providing mapping information of IP phone to capable interface where downloaded ACL is utilized. | 1.3.6.1.4.1.9.9.179.3.2.52 | current |
| caqIpAceTypeGroup OBJECT-GROUP A collection of object providing the type of an Ip ACE. | 1.3.6.1.4.1.9.9.179.3.2.53 | current |
| caqIpOperClassifierGroup OBJECT-GROUP A collection of objects provides the operational mapping of IP ACLs to each applicable interface. | 1.3.6.1.4.1.9.9.179.3.2.54 | current |
| caqDownloadClassifierGroup OBJECT-GROUP A collection of objects provides the mapping of ACLs to each applicable interface downloaded by security features. | 1.3.6.1.4.1.9.9.179.3.2.55 | current |
| caqArpLoggingSourceGroup OBJECT-GROUP A collection of objects provides the logging source of ARP flow. | 1.3.6.1.4.1.9.9.179.3.2.56 | current |