ALCATEL-IND1-TIMETRA-SAP-MIB

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

The current number of SAPs configured in this device.

OBJECT-TYPE

A table that contains basic SAP information.

OBJECT-TYPE

Information about a specific SAP.

OBJECT-TYPE

The ID of the access port where this SAP is defined.

OBJECT-TYPE

The value of the label used to identify this SAP on the access port specified by sapPortId.

OBJECT-TYPE

This object indicates the status of this row. The only values supported during a set operation are 'createAndGo' and 'destroy'.

OBJECT-TYPE

This object indicates the type of service where this SAP is defined.

OBJECT-TYPE

Generic information about this SAP.

OBJECT-TYPE

The desired state of this SAP.

OBJECT-TYPE

The value of the object sapOperStatus indicates the operating state of this SAP.

OBJECT-TYPE

The value of the object sapIngressQosPolicyId specifies the row index in the tSapIngressTable corresponding to this ingress QoS policy, or one if no policy is specified. The value 0 is needed for mirror SAPs that cannot have a qos policy assigned.

OBJECT-TYPE

The value of the object sapIngressMacFilterId specifies the row index in the tMacFilterTable corresponding to this ingress filter, or zero if no filter is specified.

OBJECT-TYPE

The value of the object sapIngressIpFilterId specifies the row index in the tIPFilterTable corresponding to this ingress filter, or zero if no filter is specified.

OBJECT-TYPE

The row index in the tSapEgressTable corresponding to this egress QoS policy, or one if no policy is specified.

OBJECT-TYPE

The row index in the tMacFilterTable corresponding to this egress filter, or zero if no filter is specified.

OBJECT-TYPE

The row index in the tIPFilterTable corresponding to this egress filter, or zero if no filter is specified.

OBJECT-TYPE

This object specifies whether traffic mirroring has been enabled on this SAP.

OBJECT-TYPE

When the value of sapType is 'ies' this object specifies the index of the IES interface where this SAP is defined. The value of this object can be set only when the row is created and cannot be changed while the row status is 'active'. This object is otherwise not significant and should have the value zero.

OBJECT-TYPE

The value of sysUpTime at the time of the most recent management-initiated change to this SAP.

OBJECT-TYPE

When the value of this object is 'true' the agent collects accounting statistics on this SAP.

OBJECT-TYPE

This object specifies the policy to use to collect accounting statistics on this SAP. The value zero indicates that the agent should use the default accounting policy, if one exists.

OBJECT-TYPE

The VPN ID of the associated service.

OBJECT-TYPE

The Customer ID of the associated service.

OBJECT-TYPE

The value of this object, when not null, indicates the Multi-Service Site this SAP is a member of. This information is used to configure the ingress and egress QoS schedulers for this SAP.

OBJECT-TYPE

This object can be set only when sapCustMultSvcSite is null. It indicates the ingress QoS scheduler for this SAP.

OBJECT-TYPE

This object can be set only when sapCustMultSvcSite is null. It indicates the egress QoS scheduler for this SAP.

OBJECT-TYPE

This object specifies the name of the split-horizon group where the SAP belongs to. This object can be set only at the time the row is created. Per default a SAP does not belong to any split-horizon group. The name specified must correspond to an existing split- horizon group in the TLS service where this SAP is defined.

OBJECT-TYPE

This object indicates the ingress shared queue policy used by this SAP. When the value of this object is null it means that the SAP will use individual ingress QoS queues, instead of the shared ones.

OBJECT-TYPE

This object applies only to SAP's defined on a port configured for qinq service encapsulation. It indicates which 802.1P bits will be used to match a QoS or a MAC filter policy when a double-tagged frame is received on this SAP.

OBJECT-TYPE

This object specifies all the conditions that affect the operating status of this SAP.

OBJECT-TYPE

The value of sysUpTime at the time of the most recent operating status change to this SAP.

OBJECT-TYPE

The value of the object sapAntiSpoofing specifies the type of anti-spoof filtering applicable on this SAP. 'nextHopIpAndMacAddr (4)' is not supported on SR-1, where the value of ALCATEL-IND1-TIMETRA-CHASSIS-MIB::tmnxChassisType is '5'.

OBJECT-TYPE

The value of the object sapIngressIpv6FilterId specifies the row index in the tIPv6FilterTable corresponding to this ingress ipv6 filter, or zero if no ipv6 filter is specified.

OBJECT-TYPE

The value of the object sapEgressIpv6FilterId specifies the row index in the tIPv6FilterTable corresponding to this egress ipv6 filter, or zero if no ipv6 filter is specified.

OBJECT-TYPE

The value of the object sapTodSuite specifies the Time of Day (ToD) suite to be applied on this SAP. An empty string indicates that no ToD suite is applied on this SAP. A set request will only be allowed, if the indicated suite is defined in TIMETRA-SCHEDULER-MIB::tmnxTodSuiteTable.

OBJECT-TYPE

When the value of sapIngressSharedQueuePolicy is not null, the value of the object sapIngUseMultipointShared specifies whether this SAP uses the multipoint-shared queues of the shared policy.

OBJECT-TYPE

When the encapsulation type of the access port where this SAP is defined is qinq, the value of the object sapEgressQinQMarkTopOnly specifies which P-bits to mark during packet egress. When the value is false both set of P-bits are marked. When the value is true, only the P-bits in the top Q-tag are marked.

OBJECT-TYPE

The value of the object sapEgressAggRateLimit specifies the maximum total rate of all egress queues for this SAP. The value '-1' means that there is no limit.

OBJECT-TYPE

The value of the object sapEndPoint specifies the service endpoint to which this SAP is attached. The svcId of the SAP MUST match the svcId of the service endpoint.

OBJECT-TYPE

The value of sapIngressVlanTranslation specifies the desired Ingress Vlan Translation. A value of 'vlanId' specifies that the value of sapIngressVlanTranslationId is to be used to overwrite the preserved VLAN id in the packet. A value of 'copyOuter' specifies that the outer VLAN id should be used to overwrite the preserved VLAN id in the packet. An 'inconsistentValue' error is returned when an attempt is made to set the value of sapIngressVlanTranslation to 'vlanId' and sapIngressVlanTranslationId is set to '-1'.

OBJECT-TYPE

The value of sapIngressVlanTranslationId specifies the VLAN id to be used to overwrite the preserved VLAN id in the packet. An 'inconsistentValue' error is returned when an attempt is made to set the value of sapIngressVlanTranslationId to other than '-1' and sapIngressVlanTranslation is not set to 'vlanId'.

OBJECT-TYPE

The value of the object sapSubType indicates the sub-type for this SAP. A value of 'regular' indicates a standard SAP. A value of 'capture' specifies a capturing SAP in which triggering packets will be sent to the CPM. Non-triggering packets captured by the 'capture' SAP will be dropped. A value of 'managed' indicates a managed SAP which was created dynamically after receiving triggering packets on a SAP with a sapSubType value of 'capture'. Entries with a value of 'managed' are not user editable and are not maintained in the configuration file. Whereas any of the three values may be returned in in response to an SNMP GET request, only two values may be specified in an SNMP SET request: 'regular' and 'capture'. An attempt to specify a value of 'managed' in an SNMP SET request will fail with an error of 'wrongValue'. The value of this object cannot be changed after creation.

OBJECT-TYPE

The value of sapCpmProtPolicyId associates a CPM Protection policy with a SAP. A value of zero (0) specifies that no CPM Protection policy is associated with this SAP. A value of one (1) specifies that the default CPM Protection policy is associated with this SAP. If no value for sapCpmProtPolicyId is specified when the sapBaseInfoEntry is created, the system assigns a default value as follows: if the system creates a corresponding entry in the sapSubMgmtInfoTable, the default value is 'one'; otherwise, the default value is 'zero'. This means that all SAP's that support Enhanced Subscriber Management get a default value of 'one'. If a SAP would get a default value of 'one', it is not allowed to set the value of sapCpmProtPolicyId to 'zero'. If a SAP would get a default value of 'zero', it is not allowed to modify the value of sapCpmProtPolicyId. This object is not supported on SR-1 and ESS-1, where the value of ALCATEL-IND1-TIMETRA-CHASSIS-MIB::tmnxChassisType is '5', and 7710, where the value of ALCATEL-IND1-TIMETRA-CHASSIS-MIB::tmnxChassisType is '7' or '9'.

OBJECT-TYPE

The value of sapCpmProtMonitorMac specifies whether the tmnxCpmProtPolPerSrcRateLimit of the CPM Protection policy must be applied. If the value of sapCpmProtMonitorMac is 'true', the per-source rate limit must be applied. If the value of sapCpmProtPolicyId is equal to zero (0), the value of sapCpmProtMonitorMac is irrelevant and will be ignored. This object is not supported on SR-1 and ESS-1, where the value of ALCATEL-IND1-TIMETRA-CHASSIS-MIB::tmnxChassisType is '5', and 7710, where the value of ALCATEL-IND1-TIMETRA-CHASSIS-MIB::tmnxChassisType is '7' or '9'.

OBJECT-TYPE

The value of sapEgressFrameBasedAccounting specifies whether to use frame-based accounting when evaluating sapEgressAggRateLimit for all egress queues for this SAP. If the value is 'false', the default packet-based accounting method will be used.

OBJECT-TYPE

A table that contains TLS SAP information.

OBJECT-TYPE

TLS specific information about a SAP.

OBJECT-TYPE

The value of the object sapTlsStpAdminStatus specifies whether this SAP participates in the TLS's Spanning Tree Protocol.

OBJECT-TYPE

The value of the object sapTlsStpPriority specifies the value of the port priority field which is contained in the most significant 4 bits of the 16-bit Port ID associated with this SAP. As only the most significant 4 bits of the value are used, the actual value of this object is limited to multiples of 16: e.g. the agent rounds down the value to one of: 0, 16, 32, .. , 224, 240.

OBJECT-TYPE

The value of the object sapTlsStpPortNum specifies the value of the port number field which is contained in the least significant 12 bits of the 16-bit Port ID associated with this SAP. Values in the range 2048..4094 are automatically assigned by the agent when the SAP is created or when the value of this object is set to zero via management. Values in the range 1..2047 can be set via management, to allow this object to have a deterministic value across system reboots.

OBJECT-TYPE

The value of the object sapTlsStpPathCost specifies the contribution of this port to the path cost of paths towards the spanning tree root which include this port.

OBJECT-TYPE

The value of the object sapTlsStpRapidStart specifies whether Rapid Start is enabled on this SAP. When the value is 'enabled' the Spanning Tree Protocol state transitions on this SAP are driven by the value of the 'HelloTime' instead of the value of 'ForwardDelay', thus allowing a faster transition into the forwarding state. This parameter is also referred to as 'adminEdge'.

OBJECT-TYPE

The value of the object sapTlsStpBpduEncap specifies the type of encapsulation used on BPDUs sent out and received on this SAP.

OBJECT-TYPE

The value of the object sapTlsStpPortState indicates the port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning it will place that port into the 'broken' state.

OBJECT-TYPE

The value of the object sapTlsStpDesignatedBridge indicates the Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment.

OBJECT-TYPE

The value of the object sapTlsStpDesignatedPort indicates the Port Identifier of the port on the Designated Bridge for this port's segment.

OBJECT-TYPE

The value of the object sapTlsStpForwardTransitions indicates the number of times this port has transitioned from the Learning state to the Forwarding state.

OBJECT-TYPE

The value of the object sapTlsStpInConfigBpdus indicates the number of Configuration BPDUs received on this SAP.

OBJECT-TYPE

The value of the object sapTlsStpInTcnBpdus indicates the number of Topology Change Notification BPDUs received on this SAP.

OBJECT-TYPE

This object specifies the number of bad BPDUs received on this SAP.

OBJECT-TYPE

The value of the object sapTlsStpOutConfigBpdus indicates the number of Configuration BPDUs sent out this SAP.

OBJECT-TYPE

This object specifies the number of Topology Change Notification BPDUs sent out this SAP.

OBJECT-TYPE

The value of the object sapTlsStpOperBpduEncap indicates the operating encapsulation type used on BPDUs sent out and received on this SAP.

OBJECT-TYPE

The value of the object sapTlsVpnId indicates the VPN ID of the associated service.

OBJECT-TYPE

The Customer ID of the associated service.

OBJECT-TYPE

The value of the object sapTlsMacAddressLimit specifies the maximum number of learned and static entries allowed in the FDB of this SAP. The value 0 means: no limit for this SAP. When the value of ALCATEL-IND1-TIMETRA-CHASSIS-MIB::tmnxChassisOperMode is not 'c', the maximum value of sapTlsMacAddressLimit is '131071'.

OBJECT-TYPE

The value of the object sapTlsNumMacAddresses indicates the number of MAC addresses currently present in the FDB that belong to this SAP (Both learned and static MAC addresses are counted).

OBJECT-TYPE

The value of the object sapTlsNumStaticMacAddresses indicates the number of static MAC addresses currently present in the FDB that belong to this SAP.

OBJECT-TYPE

The value of the object sapTlsMacLearning specifies whether the MAC learning process is enabled for this SAP. The value is ignored if MAC learning is disabled on service level.

OBJECT-TYPE

The value of the object sapTlsMacAgeing specifies whether the MAC aging process is enabled for this SAP. the value is ignored if MAC aging is disabled on service level.

OBJECT-TYPE

The value of the object sapTlsStpOperEdge indicates the operational value of the Edge Port parameter. The object is initialized to the value of sapTlsStpRapidStart and is set FALSE on reception of a BPDU.

OBJECT-TYPE

The value of the object sapTlsStpAdminPointToPoint specifies the administrative point-to-point status of the LAN segment attached to this sap. The value 'forceTrue' means that this port should always be treated as if it is connected to a point-to-point link. The value of 'forceFalse' means that this port should be treated as having a shared media connection.

OBJECT-TYPE

sapTlsStpPortRole indicates the current role of the sap as defined by the Rapid Spanning Tree Protocol.

OBJECT-TYPE

sapTlsStpAutoEdge specifies whether this SAP is enabled for auto-edge detection as defined by Rapid Spanning Tree Protocol.

OBJECT-TYPE

sapTlsStpOperProtocol indicates whether stp, rstp or mstp is running on this SAP. If the protocol is not enabled on this SAP, the value notApplicable is returned.

OBJECT-TYPE

The value of the object sapTlsStpInRstBpdus indicates the number of Rapid Spanning Tree (RST) BPDUs received on this SAP.

OBJECT-TYPE

The value of the object sapTlsStpOutRstBpdus indicates the number of Rapid Spanning Tree (RST) BPDUs sent out on this SAP.

OBJECT-TYPE

When sapTlsLimitMacMove value is set to 'blockable' the agent will monitor the MAC relearn rate on this SAP, and it will block it when the re-learn rate specified by svcTlsMacMoveMaxRate is exceeded. When the value is 'nonBlockable' this SAP will not be blocked, and another blockable SAP will be blocked instead.

OBJECT-TYPE

The value of the object sapTlsDhcpSnooping specifies whether or not DHCP packets received on this SAP will be snooped. This object was made obsolete in the 3.0 release.

OBJECT-TYPE

The value of the object sapTlsMacPinning specifies whether or not MAC address pinning is active on this SAP. The value will be set by default to disabled. However for a SAP that belongs to a residential SHG, the value is set to enabled by the system, and cannot be altered by the operator. Setting the value to enable disables re-learning of MAC addresses on other SAPs or spoke-SDPs within the same VPLS; the MAC address will hence remain attached to the SAP for the duration of its age-timer. This object has effect only for MAC addresses learned via the normal MAC learning process, and not for entries learned via DHCP.

OBJECT-TYPE

with the object sapTlsMacAddressLimit a limit can be configured for the max number of MAC addresses that will be learned on this SAP. When this limit is reached, packets with unknown source MAC address are forwarded by default. By setting sapTlsDiscardUnknownSource to enabled, packets with unknown source MAC will be dropped in stead.

OBJECT-TYPE

The value of sapTlsMvplsPruneState indicates the mVPLS prune state of the SAP. The object will be set to notApplicable if the SAP is not managed by a mVPLS. If the SAP is managed the state reflects whether or not the SAP is pruned by the STP instance running in the mVPLS instance.

OBJECT-TYPE

The value of sapTlsMvplsMgmtService indicates the service Id of the service where the STP instance is running that is managing this SAP. This object is only valid if sapTlsMvplsPruneState is different from notApplicable.

OBJECT-TYPE

The value of sapTlsMvplsMgmtPortId indicates the SAP port Id of the SAP in the mVPLS instance specified in sapTlsMvplsMgmtService that is controlling this SAP. This object is only valid if sapTlsMvplsPruneState is different from notApplicable.

OBJECT-TYPE

The value of sapTlsMvplsMgmtEncapValue indicates the SAP Encap value of the SAP in the mVPLS instance specified in sapTlsMvplsMgmtService that is controlling this SAP. This object is only valid if sapTlsMvplsPruneState is different from notApplicable.

OBJECT-TYPE

The value of the object sapTlsArpReplyAgent specifies the status of the special ARP response mechanism in the system for ARP requests destined to static or dynamic hosts associated with this SAP. disabled: the ARP reply function is not operational enabled: the ARP reply function is enabled without subscriber identification. enabledWithSubscrIdent: the ARP reply function is enabled with subscriber identification.

OBJECT-TYPE

The value of the object sapTlsStpException indicates whether an STP exception condition is present on this Sap. - none : no exception condition found. - oneWayCommuniation : The neighbor RSTP peer on this link is not able to detect our presence. - downstreamLoopDetected :A loop is detected on this link.

OBJECT-TYPE

The value of the object sapTlsAuthenticationPolicy specifies which subscriber authentication policy must be applied when a DHCP msg is received on the interface. The authentication policies must be defined in tmnxSubAuthPlcyTable. The policy will only be applied when sapTlsDhcpSnoop is enabled.

OBJECT-TYPE

The value of the object sapTlsL2ptTermination specifies whether received L2 Protocol Tunnel pdu's are terminated on this port or sap

OBJECT-TYPE

The value of the object sapTlsBpduTranslation specifies whether received L2 Protocol Tunnel pdu's are translated before being sent out on this port or sap

OBJECT-TYPE

The value of the object sapTlsStpRootGuard specifies whether this port is allowed to become STP root port. It corresponds to the parameter 'restrictedRole' in 802.1Q. If set, it can cause lack of spanning tree connectivity.

OBJECT-TYPE

The value of the object sapTlsStpInsideRegion indicates whether the network connected to the SAP is in the same MST region. It corresponds to the parameter 'infoInternal' in 802.1Q.

OBJECT-TYPE

The value of the object sapTlsEgressMcastGroup specifies the Egress Multicast Group this SAP belongs to.

OBJECT-TYPE

The value of the object sapTlsStpInMstBpdus indicates the number of Multiple Spanning Tree (MST) BPDUs received on this SAP.

OBJECT-TYPE

The value of the object sapTlsStpOutMstBpdus indicates the number of Multiple Spanning Tree (MST) BPDUs sent out on this SAP.

OBJECT-TYPE

The value of the object sapTlsRestProtSrcMac specifies how the agent will handle relearn requests for protected MAC addresses. When the value of this object is 'true' requests to relearn a protected MAC address will be ignored. In addition, if the value of sapTlsRestProtSrcMacAction is 'disable', then the SAP where the protected source MAC was seen will be brought operationally down.

OBJECT-TYPE

The value of the object sapTlsRestUnprotDstMac specifies how the system will forward packets destined to an unprotected MAC address. When the value of this object is 'true' packets destined to an unprotected MAC address will be dropped.

OBJECT-TYPE

The value of the object sapTlsStpRxdDesigBridge indicates the designated Bridge Identifier in the last BPDU which was received on this SAP. It identifies which bridge is connected to the SAP.

OBJECT-TYPE

The value of the object sapTlsStpRootGuardViolation indicates whether there is a root-guard violation at the present time. This can only happen when sapTlsStpRootGuard is set to true.

OBJECT-TYPE

The value of the object sapTlsShcvAction indicates whether any action should be triggered when the connectivity check fails.

OBJECT-TYPE

The value of the object sapTlsShcvSrcIp specifies the source IP address used when doing the connectivity check. The value 0.0.0.0 indicates that no host IP address is specified.

OBJECT-TYPE

The value of the object sapTlsShcvSrcMac specifies the MAC address used when doing the connectivity check. The value 0:0:0:0:0:0 indicates that no host MAC address is specified.

OBJECT-TYPE

The value of the object sapTlsShcvInterval specifies the interval in minutes between connectivity checks. Zero means no connectivity checking.

OBJECT-TYPE

The value of the object sapTlsMvplsMgmtMsti indicates the MST-instance in the mVPLS instance specified in sapTlsMvplsMgmtService that is controlling this SAP. A value of 0 indicates the CIST. This object is only valid if sapTlsMvplsPruneState is different from notApplicable.

OBJECT-TYPE

The value of the object sapTlsMacMoveNextUpTime counts down the time in seconds until a SAP that has been brought down due to exceeding the TLS svcTlsMacMoveMaxRate, sapOperFlags 'relearnLimitExceeded', is automatically brought up again. When this value is 0xffff, the SAP will never be automatically brought up. The value is zero when sapOperStatus is 'up'.

OBJECT-TYPE

The value of the object sapTlsMacMoveRateExcdLeft counts down the number of times this SAP can exceed the TLS svcTlsMacMoveMaxRate and still be automatically brought up.

OBJECT-TYPE

The value of the object sapTlsRestProtSrcMacAction indicates the action to take whenever a relearn request for a protected MAC is received on a restricted SAP. When the value of this object is 'disable' the SAP will be placed in the operational down state, with the operating flag 'recProtSrcMac' set. When the value of this object is 'alarm-only', the SAP will be left up and only a notification, sapReceivedProtSrcMac, will be generated.

OBJECT-TYPE

The value of sapTlsL2ptForceBoundary specifies if sapTlsL2ptTermination is enforced for its managed SAP's. Setting the value of the object sapTlsL2ptForceBoundary of a SAP in a Management VPLS to `true' forces all its managed SAP's to have sapTlsL2ptTermination enabled. This value can only be `true' if the SAP belongs to a management VPLS. If this SAP has managed SAP's already with sapTlsL2ptTermination disabled, it is not allowed to set sapTlsL2ptForceBoundary to `true'.

OBJECT-TYPE

The value of the object sapTlsLimitMacMoveLevel specifies the hierarchy in which SAPs are blocked when a MAC-move limit is exceeded. When a MAC is moving among multiple SAPs or spoke-SDPs, the SAP bind or spoke-SDP bind with the lower level is blocked first. (tertiary is the lowest)

OBJECT-TYPE

The value of the object sapTlsBpduTransOper indicates the operational bpdu encapsulation used for BPDU translated frames.

OBJECT-TYPE

The value of sapTlsDefMsapPolicy specifies the default Managed SAP policy to use to create Managed SAPs when the response from the Radius server does not specify a Managed SAP policy. The value of sapTlsDefMsapPolicy is only valid for a SAP with a sapSubType value of 'capture'. If the value is set to a non-empty string for a SAP with a sapSubType value other than 'capture', an 'inconsistentValue' error will be returned. The Managed SAP policy must be defined in msapPlcyTable, otherwise an 'inconsistentValue' error will be returned.

OBJECT-TYPE

The value of the object sapTlsL2ptTermination specifies which L2 Protocol Tunnel pdu's are terminated on this port or sap

OBJECT-TYPE

The value of the object sapTlsL2ptForceProtocols specifies which L2 Protocol Tunnel pdu's must be terminated by SAP's managed by this SAP. This object is only relevant if the value of the object sapTlsL2ptForceBoundary is 'true'. For every SAP managed by this SAP, each L2 protocol specified by sapTlsL2ptForceProtocols must be terminated, while other L2 protocols may or may not be terminated, depending on the value of sapTlsL2ptProtocols of that managed SAP.

OBJECT-TYPE

The value of sapTlsPppoeMsapTrigger specifies whether the receipt of PPPoE trigger packets on a VPLS SAP with a sapSubType value of 'capture' will result in a Radius authentication that will provide a service context and the creation of a SAP with a sapSubType value of 'managed'. An attempt to set the value sapTlsPppoeMsapTrigger to 'true' on a SAP with sapSubType other than 'capture' will return an 'inconsistentValue' error.

OBJECT-TYPE

The value of sapTlsDhcpMsapTrigger specifies whether the receipt of DHCP trigger packets on this VPLS SAP with a sapSubType value of 'capture' will result in a Radius authentication that will provide a service context and the creation of a SAP with a sapSubType value of 'managed'. An attempt to set the value sapTlsDhcpMsapTrigger to 'true' on a SAP with sapSubType other than 'capture' will return an 'inconsistentValue' error.

OBJECT-TYPE

The value of sapTlsMrpJoinTime specifies a timer value in 10ths of seconds which determines the maximum rate at which attribute join messages can be sent on the SAP.

OBJECT-TYPE

The value of sapTlsMrpLeaveTime specifies a timer value in 10ths of seconds which determines the amount of time a registered attribute is held in leave state before the registration is removed.

OBJECT-TYPE

The value of sapTlsMrpLeaveAllTime specifies the a timer value in 10ths of seconds which determines the frequency where all attribute declarations on the SAP are all refreshed.

OBJECT-TYPE

The value of sapTlsMrpPeriodicTime specifies a timer value in 10ths of seconds which determines the frequency of re-transmission of attribute declarations.

OBJECT-TYPE

The value of sapTlsMrpPeriodicEnabled specifies whether re-transmission of attribute declarations is enabled.

OBJECT-TYPE

A table that contains ATM SAP information.

OBJECT-TYPE

Information about a specific ATM SAP.

OBJECT-TYPE

This object specifies the data encapsulation used over the AAL5 SSCS layer. The definition references RFC 2684 Multiprotocol Encapsulation over ATM AAL5 and to the ATM Forum LAN Emulation specification.

OBJECT-TYPE

This object specifies the index of the ATM traffic descriptor in the ATM traffic data encapsulation used in for the ingress direction over the AAL5 SSCS layer. The definition references RFC 2684 Multiprotocol Encapsulation over ATM AAL5 and to the ATM Forum LAN Emulation specification.

OBJECT-TYPE

This object specifies the index of the ATM traffic descriptor in the ATM traffic data encapsulation used in for the egress direction over the AAL5 SSCS layer. The definition references RFC 2684 Multiprotocol Encapsulation over ATM AAL5 and to the ATM Forum LAN Emulation specification.

OBJECT-TYPE

A value of up specifies that the OAM status of a pvc affects the sap operational status and OAM AIS/RDI cell generation upon a sap operational status of down. A value of down specifies that the OAM status of a pvc will not affect the operational status of the associated sap and no OAM AIS/RDI cells are generated.

OBJECT-TYPE

The sapAtmOamTerminate object specifies whether this SAP will act as an OAM termination point. If enabled, OAM cells will be sunk by the SAP and can affect the SAP's operational status (if sapAtmOamAlarmCellHandling is also enabled). Otherwise the OAM cells will be passed into the APIPE service. This object is only configurable for ATM SAPs that are part of an APIPE service SDU or VCC mode. If the sapPortId belongs to an Multi-Chassis APS port, the default value is up.

OBJECT-TYPE

The sapAtmOamPeriodicLoopback object specifies whether this SAP will run periodic OAM loopbacks or not. If enabled, an ATM OAM loopback cell will be transmitted every period as configured in tAtmSysOamLoopbackPeriod. If a response is not received and tAtmSysOamRetryDown consecutive retries also result in failure, the endpoint will transition to the eteAisLoc state. Once in the eteAisLoc state, an ATM OAM loopback cell will be transmitted every period as configured in tAtmSysOamLoopbackPeriod. If a response is received for the periodic loopback and tAtmSysOamRetryUp consecutive retries also each receive a response, the endpoint will transition back to the up state. This object is only configurable on IES or VPRN service endpoints.

OBJECT-TYPE

A table that contains basic SAP statistics. In the descriptions below 'Pchip' refers to the Alcatel 7x50 SR series Packet Processing chip, while 'Qchip' refers to the Alcatel 7x50 SR series QoS Queueing Engine chip.

OBJECT-TYPE

Basic statistics about a specific SAP.

OBJECT-TYPE

The number of packets dropped by the ingress Pchip due to: SAP state, ingress MAC, IP or IPv6 filter, same segment discard, bad checksum, etc.

OBJECT-TYPE

The number of octets dropped by the ingress Pchip due to: SAP state, ingress MAC, IP or IPv6 filter, same segment discard, bad checksum, etc.

OBJECT-TYPE

The number of high priority packets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip.

OBJECT-TYPE

The number of high priority octets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip.

OBJECT-TYPE

The number of low priority packets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip.

OBJECT-TYPE

The number of low priority octets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip.

OBJECT-TYPE

The number of high priority packets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The number of high priority octets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The number of low priority packets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The number of low priority octets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The number of in-profile packets (rate below CIR) forwarded by the ingress Qchip.

OBJECT-TYPE

The number of in-profile octets (rate below CIR) forwarded by the ingress Qchip.

OBJECT-TYPE

The number of out-of-profile packets (rate above CIR) forwarded by the ingress Qchip.

OBJECT-TYPE

The number of out-of-profile octets (rate above CIR) forwarded by the ingress Qchip.

OBJECT-TYPE

The number of in-profile packets discarded by the egress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The number of in-profile octets discarded by the egress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The number of out-of-profile packets discarded by the egress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The number of out-of-profile packets discarded by the egress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The number of in-profile packets (rate below CIR) forwarded by the egress Qchip.

OBJECT-TYPE

The number of in-profile octets (rate below CIR) forwarded by the egress Qchip.

OBJECT-TYPE

The number of out-of-profile packets (rate above CIR) forwarded by the egress Qchip.

OBJECT-TYPE

The number of out-of-profile octets (rate above CIR) forwarded by the egress Qchip.

OBJECT-TYPE

The Customer ID for the associated service.

OBJECT-TYPE

The number of uncolored packets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip.

OBJECT-TYPE

The number of uncolored octets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip.

OBJECT-TYPE

The number of DHCP packets discarded as result of authentication.

OBJECT-TYPE

The number of DHCP packets successfully authenticated.

OBJECT-TYPE

The value of sapBaseStatsLastClearedTime indicates the sysUpTime when the counters in this table were last cleared.

OBJECT-TYPE

A table that contains ingress QoS queue SAP statistics.

OBJECT-TYPE

Ingress statistics about a specific SAP's QoS queue.

OBJECT-TYPE

The index of the ingress QoS queue of this SAP.

OBJECT-TYPE

The number of high priority packets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip.

OBJECT-TYPE

The number of high priority packets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The number of low priority packets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip.

OBJECT-TYPE

The number of low priority packets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The number of high priority octets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip.

OBJECT-TYPE

The number of high priority octets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The number of low priority octets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip.

OBJECT-TYPE

The number of low priority octets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The number of in-profile packets (rate below CIR) forwarded by the ingress Qchip.

OBJECT-TYPE

The number of out-of-profile packets (rate above CIR) forwarded by the ingress Qchip.

OBJECT-TYPE

The number of in-profile octets (rate below CIR) forwarded by the ingress Qchip.

OBJECT-TYPE

The number of out-of-profile octets (rate above CIR) forwarded by the ingress Qchip.

OBJECT-TYPE

The Customer ID for the associated service.

OBJECT-TYPE

The number of uncolored packets offered to the ingress Qchip.

OBJECT-TYPE

The number of uncolored octets offered to the ingress Qchip.

OBJECT-TYPE

A table that contains egress QoS queue SAP statistics.

OBJECT-TYPE

Egress statistics about a specific SAP's QoS queue.

OBJECT-TYPE

The index of the egress QoS queue of this SAP.

OBJECT-TYPE

The number of in-profile packets (rate below CIR) forwarded by the egress Qchip.

OBJECT-TYPE

The number of in-profile packets discarded by the egress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The number of out-of-profile packets (rate above CIR) forwarded by the egress Qchip.

OBJECT-TYPE

The number of out-of-profile packets discarded by the egress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The number of in-profile octets (rate below CIR) forwarded by the egress Qchip.

OBJECT-TYPE

The number of in-profile octets discarded by the egress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The number of out-of-profile octets (rate above CIR) forwarded by the egress Qchip.

OBJECT-TYPE

The number of out-of-profile octets discarded by the egress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The Customer ID for the associated service.

OBJECT-TYPE

A table that contains ingress QoS queue SAP statistics.

OBJECT-TYPE

Ingress statistics about a specific SAP's QoS queue.

OBJECT-TYPE

The index of the ingress QoS scheduler of this SAP.

OBJECT-TYPE

The number of forwarded packets, as determined by the SAP ingress scheduler policy, offered by the Pchip to the Qchip.

OBJECT-TYPE

The number of forwarded octets, as determined by the SAP ingress scheduler policy, offered by the Pchip to the Qchip.

OBJECT-TYPE

The Customer ID for the associated service.

OBJECT-TYPE

A table that contains ingress QoS queue SAP statistics.

OBJECT-TYPE

Egress statistics about a specific SAP's QoS queue.

OBJECT-TYPE

The index of the egress QoS scheduler of this SAP.

OBJECT-TYPE

The number of forwarded packets by the egress Qchip, as determined by the SAP egress scheduler policy.

OBJECT-TYPE

The number of forwarded octets by the egress Qchip, as determined by the SAP egress scheduler policy.

OBJECT-TYPE

The Customer ID for the associated service.

OBJECT-TYPE

This table is used only for SAPs that are part of a management VPLS. It indicates for each SAP the ranges of associated VLANs that will be affected when the SAP changes state.

OBJECT-TYPE

Each row specifies a range of VLANS associated with a SAP of a MVPLS. Ranges may contains overlapping sections only for Mvpls SAPs that belong to the same service.

OBJECT-TYPE

The value of sapTlsMvplsMinVlanTag specifies the left bound (i.e. min. value) of a range of VLANs that are associated with the Mvpls SAP. sapTlsMvplsMinVlanTag must be smaller than (or equal to) sapTlsMvplsMaxVlanTag. Special values are: 0: this value is reserved for the null tag. 4095: this value denotes the default SAP.

OBJECT-TYPE

The value of sapTlsMvplsMaxVlanTag specifies the right bound (i.e. max. value) of a range of VLANs that are associated with the Mvpls SAP. Special values are: 0: this value is reserved for the null tag. 4095: this value denotes the default SAP.

OBJECT-TYPE

The value of sapTlsMvplsRowStatus specifies the status of this row. The only values supported during a set operation are 'createAndGo' and 'destroy'. A row (i.e. a range of VLAN tags) can be destroyed only if there are no SAPs defined in regular VPLSses in this range.

OBJECT-TYPE

The sapAntiSpoofTable contains information about anti-spoofing filters on a SAP.

OBJECT-TYPE

An entry in the sapAntiSpoofTable.

OBJECT-TYPE

The value of sapAntiSpoofIpAddress indicates the IP address for which this table entry contains information.

OBJECT-TYPE

The value of sapAntiSpoofMacAddress indicates the MAC address for which this table entry contains information.

OBJECT-TYPE

The sapStaticHostTable is used to configure static hosts on a SAP.

OBJECT-TYPE

Each row entry represents information on a statically configured host. Entries can be created and deleted via SNMP SET operations.

OBJECT-TYPE

The value of the object sapStaticHostRowStatus controls the creation and deletion of rows in this table.

OBJECT-TYPE

The value of the object sapStaticHostIpAddress specifies the IP address associated with this static host. The value 0.0.0.0 indicates that no host IP address is specified.

OBJECT-TYPE

The value of the object sapStaticHostMacAddress specifies the MAC address associated with this static host. The value 0:0:0:0:0:0 indicates that no host MAC address is specified.

OBJECT-TYPE

The value of the object sapStaticHostSubscrIdent specifies the subscriber identification for this static host.

OBJECT-TYPE

The value of the object sapStaticHostSubProfile specifies the subscriber profile for this static host. The specified subscriber profile needs to exists in the TIMETRA-SUBSCRIBER-MGMT-MIB::tmnxSubProfileTable.

OBJECT-TYPE

The value of the object sapStaticHostSlaProfile specifies the SLA profile for this static host. The specified SLA profile needs to exists in the TIMETRA-SUBSCRIBER-MGMT-MIB::tmnxSLAProfileTable.

OBJECT-TYPE

The value of the object sapStaticHostShcvOperState gives the state of the subscriber host connectivity check for this static host.

OBJECT-TYPE

The value of the object sapStaticHostShcvChecks specifies the number of connectivity checks for this static host.

OBJECT-TYPE

The value of the object sapStaticHostShcvReplies specifies the number of host replies for this static host.

OBJECT-TYPE

The value of the object sapStaticHostShcvReplyTime gives the timestamp of the last successful connectivity check for this static host.

OBJECT-TYPE

The value of the object sapStaticHostDynMacAddress gives the MAC address learned via ARP in case this is an IP-only static host (sapStaticHostMacAddress is set to 0:0:0:0:0:0). The value 0:0:0:0:0:0 indicates that no MAC address is learned yet.

OBJECT-TYPE

The value of the object sapStaticHostRetailerSvcId indicates the service ID of the retailer VPRN service to which this static host belongs. When this object is non zero, the static host belongs to a retailer VPRN.

OBJECT-TYPE

The value of the object sapStaticHostRetailerIf indicates the interface index of the retailer VPRN interface to which this static host belongs. When this object is non zero, the static host belongs to a retailer VPRN.

OBJECT-TYPE

The value of sapStaticHostFwdingState indicates the forwarding state of this static host. When the value is 'outOfService', host traffic is not forwarded. When it is 'inService', host traffic is forwarded.

OBJECT-TYPE

The value of sapStaticHostAncpString specifies the ancp-string associated to this SAP host.

OBJECT-TYPE

The value of the object sapStaticHostSubIdIsSapId specifies whether the SAP-id is taken as subscriber identification for this static host.

OBJECT-TYPE

The value of sapStaticHostAppProfile specifies the application profile for this static host. The specified application profile needs to exist in the TIMETRA-BSX-MIB::tmnxBsxAppProfTable.

OBJECT-TYPE

The value of sapStaticHostIntermediateDestId specifies to which intermediate destination (for example a DSLAM) this host belongs.

OBJECT-TYPE

sapTlsDhcpInfoTable contains DHCP information related to a TLS SAP. This table complements sapTlsInfoTable, and contains an entry for each Tls SAP. Rows in this table are created and deleted automatically by the system.

OBJECT-TYPE

DHCP specific information for a TLS SAP.

OBJECT-TYPE

The value of the object sapTlsDhcpAdminState specifies the overall enable/disable state of all DHCP related actions on this Sap. The value 'disabled' allows the user to configure individual DHCP commands but administratively disable them.

OBJECT-TYPE

The value of the object sapTlsDhcpDescription specifies a user provided description for DHCP on this Sap. It consists of any printable, seven-bit ASCII characters up to 80 characters in length.

OBJECT-TYPE

The value of the object sapTlsDhcpSnoop specifies the enable/disable state for DHCP snooping on this Sap. Note that in order for snooping to be enabled the object sapTlsDhcpAdminState must also have the value enabled.

OBJECT-TYPE

The value of the object sapTlsDhcpLeasePopulate specifies the maximum number of DHCP lease states allowed on this SAP.

OBJECT-TYPE

The value of the object sapTlsDhcpOperLeasePopulate indicates the number of DHCP lease states currently allocated on this SAP.

OBJECT-TYPE

The value of the object sapTlsDhcpInfoAction specifies the DHCP option reforwarding policy: 'replace' - replace existing information with configured information 'drop' - discard messages with existing relay information if the option-82 information is also present. 'keep' - retain the existing relay information.

OBJECT-TYPE

The value of the object sapTlsDhcpCircuitId specifies whether or not the circuit-id suboption is present, and if it is present what information goes in it: - 'none' the circuit-id suboption will not be part of the information option (Option 82). - 'asciiTuple' the ASCII-encoded concatenated tuple consisting of the - access-node-identifier - service-id - interface-name is used. - 'vlanAsciiTuple' the format will include VLAN-id and dot1p bits in addition to what is included in ascii-tuple already. The format is supported on dot1q and qinq encapsulated ports only. Thus, when the option 82 bits are stripped, dot1p bits will be copied to the Ethernet header of an outgoing packet.

OBJECT-TYPE

The value of the object sapTlsDhcpRemoteId specifies what information goes into the remote-id suboption in the DHCP Relay packet. If the value of this object is set to 'none', the remote-id suboption will not be part of the information option (Option 82). If the value of this object is set to 'mac', the MAC address of the remote end is encoded in the suboption. If the value of this object is set to 'remote-id', sapTlsDhcpRemoteIdString will represent the remote-id. By default, the remote-id value is none.

OBJECT-TYPE

The value of the object sapTlsDhcpRemoteIdString specifies the remote-id. This object exists only if sapTlsDhcpRemoteId has a value of 'remote-id'.

OBJECT-TYPE

The value of sapTlsDhcpProxyAdminState specifies the desired administrative state of the proxy server on this interface. Note that in order for the proxy server to be enabled, the value of sapTlsDhcpAdminState must also be 'enabled'.

OBJECT-TYPE

The value of sapTlsDhcpProxyServerAddr specifies the IP address which will be used as the source address of the emulated DHCP server in the context of this VPLS SAP. This address is mandatory for the proxy server capability and it should be in the context of the subnet represented by this VPLS.

OBJECT-TYPE

The value of sapTlsDhcpProxyLeaseTime specifies in seconds how long a DHCP client is allowed to use the offered IP address. Value 0 means the lease time provided by a RADIUS or an upstream DHCP server will not be overridden. A lease time of 7 days is used when RADIUS does not provide a lease time.

OBJECT-TYPE

The value of sapTlsDhcpProxyLTRadiusOverride specifies whether or not the lease time provided by the RADIUS server is presented to the DHCP client. By default the proxy-server will always make use of sapTlsDhcpProxyLeaseTime, regardless of what lease time information is provided from the RADIUS server. When sapTlsDhcpProxyLTRadiusOverride is set to 'true', the proxy-server will use the lease time information provided by the RADIUS server, regardless of the configured one.

OBJECT-TYPE

The value of sapTlsDhcpVendorIncludeOptions specifies what is encoded in the Alcatel vendor specific sub-option of option 82. The value of this object is only used when sapTlsDhcpInfoAction is 'replace'.

OBJECT-TYPE

The value of sapTlsDhcpVendorOptionString specifies the string that goes into the Alcatel vendor specific sub-option of option 82. This string is only used when sapTlsDhcpInfoAction is set to 'replace'.

OBJECT-TYPE

sapTlsDhcpStatsTable contains DHCP statistics related to a TLS SAP. This table complements sapTlsInfoTable, and contains an entry for each Tls SAP. Rows in this table are created and deleted automatically by the system.

OBJECT-TYPE

DHCP statistics for a TLS SAP.

OBJECT-TYPE

The value of the object sapTlsDhcpStatsClntSnoopdPckts indicates the number of DHCP client packets that have been snooped on this SAP.

OBJECT-TYPE

The value of the object sapTlsDhcpStatsSrvrSnoopdPckts indicates the number of DHCP server packets that have been snooped on this SAP.

OBJECT-TYPE

The value of the object sapTlsDhcpStatsClntForwdPckts indicates the number of DHCP client packets that have been forwarded on this SAP.

OBJECT-TYPE

The value of the object sapTlsDhcpStatsSrvrForwdPckts indicates the number of DHCP server packets that have been forwarded on this SAP.

OBJECT-TYPE

The value of the object sapTlsDhcpStatsClntDropdPckts indicates the number of DHCP client packets that have been dropped on this SAP.

OBJECT-TYPE

The value of the object sapTlsDhcpStatsSrvrDropdPckts indicates the number of DHCP server packets that have been dropped on this SAP.

OBJECT-TYPE

The value of the object sapTlsDhcpStatsClntProxRadPckts indicates the number of DHCP client packets that have been proxied on this SAP based on data received from a RADIUS server.

OBJECT-TYPE

The value of the object sapTlsDhcpStatsClntProxLSPckts indicates the number of DHCP client packets that have been proxied on this SAP based on a lease state. The lease itself can have been obtained from a DHCP or RADIUS server. This is the so called lease split functionality.

OBJECT-TYPE

The value of the object sapTlsDhcpStatsGenReleasePckts indicates the number of DHCP RELEASE messages spoofed on this SAP to the DHCP server.

OBJECT-TYPE

The value of the object sapTlsDhcpStatsGenForceRenPckts indicates the number of DHCP FORCERENEW messages spoofed on this SAP to the DHCP clients.

OBJECT-TYPE

sapTlsDhcpLeaseStateTable contains DHCP lease state info for a TLS SAP. This table complements sapTlsInfoTable, and contains an entry for each Tls SAP. Rows in this table are created and deleted automatically by the system. The content of this table is moved to the svcDhcpLeaseStateTable.

OBJECT-TYPE

DHCP Lease State information on a TLS SAP.

OBJECT-TYPE

The value of the object sapTlsDhcpLseStateCiAddr indicates the IP address of the DHCP lease state.

OBJECT-TYPE

The value of the object sapTlsDhcpLseStateChAddr indicates the MAC address of the DHCP lease state.

OBJECT-TYPE

The value of the object sapTlsDhcpLseStateRemainLseTime indicates the remaining lease time of the Ip address of the DHCP lease state. This object was made obsolete in the 4.0 release.

OBJECT-TYPE

The value of the object sapTlsDhcpLseStateOption82 indicates the content of the Option82 for this DHCP lease state. This object was made obsolete in the 4.0 release.

OBJECT-TYPE

The value of the object sapTlsDhcpLseStatePersistKey indicates a key value that can be used to track this lease state in the persistence file. This object was made obsolete in the 4.0 release.

OBJECT-TYPE

The sapPortIdIngQosSchedStatsTable contains ingress QoS queue SAP statistics. This table is used when the SAP is a CCAG or LAG in 'link' mode, or an APS.

OBJECT-TYPE

Each entry represents the ingress statistics about a specific SAP's QoS queue. Entries are created when a scheduler policy is applied to a SAP.

OBJECT-TYPE

The value of sapPortIdIngQosSchedName is used as an index of the ingress QoS scheduler of this SAP.

OBJECT-TYPE

The value of sapPortIdIngPortId is used as an index of the ingress QoS scheduler of this SAP. When the SAP is an aps/ccag/lag in 'link' mode, this object is the TmnxPortID of the member-port on which the scheduler is applied.

OBJECT-TYPE

The value of sapPortIdIngQosSchedFwdPkts indicates the number of forwarded packets, as determined by the SAP ingress scheduler policy, offered by the Pchip to the Qchip.

OBJECT-TYPE

The value of sapPortIdIngQosSchedFwdOctets indicates the number of forwarded octets,as determined by the SAP ingress scheduler policy, offered by the Pchip to the Qchip.

OBJECT-TYPE

The value of sapPortIdIngQosSchedCustId indicates the Customer ID for the associated service.

OBJECT-TYPE

The sapPortIdEgrQosSchedStatsTable contains egress QoS queue SAP statistics. This table is used when the SAP is a CCAG or LAG in 'link' mode, or an APS.

OBJECT-TYPE

Each entry represents the egress statistics about a specific SAP's QoS queue. Entries are created when a scheduler policy is applied to a SAP.

OBJECT-TYPE

The value of sapPortIdEgrQosSchedName is used as an index of the egress QoS scheduler of this SAP.

OBJECT-TYPE

The value of sapPortIdEgrPortId is used as an index of the egress QoS scheduler of this SAP. When the SAP is an aps/ccag/lag in 'link' mode, this object is the TmnxPortID of the member-port on which the scheduler is applied.

OBJECT-TYPE

The value of sapPortIdEgrQosSchedFwdPkts indicates the number of forwarded packets, as determined by the SAP egress scheduler policy, offered by the Pchip to the Qchip.

OBJECT-TYPE

The value of sapPortIdEgrQosSchedFwdOctets indicates the number of forwarded octets,as determined by the SAP egress scheduler policy, offered by the Pchip to the Qchip.

OBJECT-TYPE

The value of sapPortIdEgrQosSchedCustId indicates the Customer ID for the associated service.

OBJECT-TYPE

This table is used to override the base parameters of a queue, as defined in the associated SAP ingress QoS policy.

OBJECT-TYPE

Override values for the specified SAP ingress QoS queue. These values override the corresponding ones specified in the associated SAP ingress QoS policy.

OBJECT-TYPE

The value of sapIngQosQId indicates the ID of the queue whose parameters are to be overridden.

OBJECT-TYPE

The value of sapIngQosQRowStatus controls the creation and deletion of rows in this table.

OBJECT-TYPE

The value of sapIngQosQLastMgmtChange indicates the value of sysUpTime at the time of the last management change of any writable object of this row.

OBJECT-TYPE

The value of sapIngQosQOverrideFlags specifies the set of attributes whose values have been overridden via management on this queue. Clearing a given flag will return the corresponding overridden attribute to the value defined on the SAP's ingress QoS policy.

OBJECT-TYPE

The value of sapIngQosQCBS specifies the amount of reserved buffer space (in kilo bytes) for this queue.

OBJECT-TYPE

The value of sapIngQosQMBS specifies the maximum amount of buffer space (in kilo bytes) allowed for this queue.

OBJECT-TYPE

The value of sapIngQosQHiPrioOnly specifies the percentage of buffer space for this queue, used exclusively by high priority packets.

OBJECT-TYPE

The value of sapIngQosQCIRAdaptation specifies the criteria to use to compute the operational CIR value for this queue, while maintaining a minimum offset.

OBJECT-TYPE

The value of sapIngQosQPIRAdaptation specifies the criteria to use to compute the operational PIR value for this queue, while maintaining a minimum offset.

OBJECT-TYPE

The value of sapIngQosQAdminPIR specifies the desired PIR value for this queue.

OBJECT-TYPE

The value of sapIngQosQAdminCIR specifies the desired CIR value for this queue.

OBJECT-TYPE

This table is used to override the base parameters of a queue, as defined in the associated SAP egress QoS policy.

OBJECT-TYPE

Override values for the specified SAP egress QoS queue. These values override the corresponding ones specified in the associated SAP egress QoS policy.

OBJECT-TYPE

The value of sapEgrQosQId indicates the ID of the queue whose parameters are to be overridden.

OBJECT-TYPE

The value of sapEgrQosQRowStatus controls the creation and deletion of rows in this table.

OBJECT-TYPE

The value of sapEgrQosQLastMgmtChange indicates the value of sysUpTime at the time of the last management change of any writable object of this row.

OBJECT-TYPE

The value of sapEgrQosQOverrideFlags specifies the set of attributes whose values have been overridden via management on this queue. Clearing a given flag will return the corresponding overridden attribute to the value defined on the SAP's ingress QoS policy.

OBJECT-TYPE

The value of sapEgrQosQCBS specifies the amount of reserved buffer space (in kilo bytes) for this queue.

OBJECT-TYPE

The value of sapEgrQosQMBS specifies the maximum amount of buffer space (in kilo bytes) allowed for this queue.

OBJECT-TYPE

The value of sapEgrQosQHiPrioOnly specifies the percentage of buffer space for this queue, used exclusively by high priority packets.

OBJECT-TYPE

The value of sapEgrQosQCIRAdaptation specifies the criteria to use to compute the operational CIR value for this queue, while maintaining a minimum offset.

OBJECT-TYPE

The value of sapEgrQosQPIRAdaptation specifies the criteria to use to compute the operational PIR value for this queue, while maintaining a minimum offset.

OBJECT-TYPE

The value of sapEgrQosQAdminPIR specifies the desired PIR value for this queue.

OBJECT-TYPE

The value of sapEgrQosQAdminCIR specifies the desired CIR value for this queue.

OBJECT-TYPE

The value of sapEgrQosQAvgOverhead specifies the encapsulation overhead, in hundredths of a percent, used to translate packet-based rate to frame-based rate and vice versa.

OBJECT-TYPE

This table is used to override the base parameters of a virtual scheduler, as defined in the associated SAP ingress scheduler policy.

OBJECT-TYPE

Override values for the specified SAP ingress virtual scheduler. These values override the corresponding ones specified in the associated SAP ingress scheduler policy.

OBJECT-TYPE

The value of sapIngQosSName indicates the name of the virtual scheduler whose parameters are to be overridden.

OBJECT-TYPE

The value of sapIngQosSRowStatus controls the creation and deletion of rows in this table.

OBJECT-TYPE

The value of sapIngQosSLastMgmtChange indicates the value of sysUpTime at the time of the last management change of any writable object of this row.

OBJECT-TYPE

The value of sapIngQosSOverrideFlags specifies the set of attributes whose values have been overridden via management on this virtual scheduler. Clearing a given flag will return the corresponding overridden attribute to the value defined on the SAP's ingress scheduler policy.

OBJECT-TYPE

The value of sapIngQosSPIR specifies the desired PIR value for this virtual scheduler.

OBJECT-TYPE

The value of sapIngQosSCIR specifies the desired CIR value for this virtual scheduler.

OBJECT-TYPE

The value of sapIngQosSSummedCIR specifies if the CIR should be used as the summed CIR values of the children schedulers or queues. If set to 'true', the applicable scheduler CIR (sapIngQosSCIR) loses its meaning.

OBJECT-TYPE

This table is used to override the base parameters of a virtual scheduler, as defined in the associated SAP egress scheduler policy.

OBJECT-TYPE

Override values for the specified SAP egress virtual scheduler. These values override the corresponding ones specified in the associated SAP egress scheduler policy.

OBJECT-TYPE

The value of sapEgrQosSName indicates the name of the virtual scheduler whose parameters are to be overridden.

OBJECT-TYPE

The value of sapEgrQosSRowStatus controls the creation and deletion of rows in this table.

OBJECT-TYPE

The value of sapEgrQosSLastMgmtChange indicates the value of sysUpTime at the time of the last management change of any writable object of this row.

OBJECT-TYPE

The value of sapEgrQosSOverrideFlags specifies the set of attributes whose values have been overridden via management on this virtual scheduler. Clearing a given flag will return the corresponding overridden attribute to the value defined on the SAP's egress scheduler policy.

OBJECT-TYPE

The value of sapEgrQosSPIR specifies the desired PIR value for this virtual scheduler.

OBJECT-TYPE

The value of sapEgrQosSCIR specifies the desired CIR value for this virtual scheduler.

OBJECT-TYPE

The value of sapEgrQosSSummedCIR specifies if the CIR should be used as the summed CIR values of the children schedulers or queues. If set to 'true', the applicable scheduler CIR (sapEgrQosSCIR) loses its meaning.

OBJECT-TYPE

A table that contains SAP subscriber management information.

OBJECT-TYPE

Subscriber management specific information about a SAP.

OBJECT-TYPE

The value of sapSubMgmtAdminStatus specifies whether enhanced subscriber management is enabled on this SAP.

OBJECT-TYPE

The value of sapSubMgmtDefSubProfile specifies the default subscriber profile applicable on this SAP. The corresponding profile is defined in TIMETRA-SUBSCRIBER-MGMT-MIB::tmnxSubProfileTable. A value of 'default' is not allowed for this object.

OBJECT-TYPE

The value of sapSubMgmtDefSlaProfile specifies the default SLA profile applicable on this SAP. The corresponding profile is defined in TIMETRA-SUBSCRIBER-MGMT-MIB::tmnxSLAProfileTable.

OBJECT-TYPE

The value of sapSubMgmtSubIdentPolicy specifies the subscriber identification policy applicable on this SAP. The corresponding policy is defined in TIMETRA-SUBSCRIBER-MGMT-MIB::tmnxSubIdentPolicyTable.

OBJECT-TYPE

The value of sapSubMgmtSubscriberLimit specifies the maximum number of subscribers allowed for this SAP. If the value is 0, there is no limit. Only if the value is 1, the 'single-sub-parameters' defined with objects sapSubMgmtProfiledTrafficOnly, sapSubMgmtNonSubTrafficSubProf and sapSubMgmtNonSubTrafficSlaProf are meaningful.

OBJECT-TYPE

The value of sapSubMgmtProfiledTrafficOnly specifies whether only profiled traffic is applicable for this SAP. If set to 'true', all SAP queues will be deleted. The value of this object is only meaningful if sapSubMgmtSubscriberLimit is set to 1.

OBJECT-TYPE

The value of sapSubMgmtNonSubTrafficSubIdent specifies the subscriber identification applicable on this SAP for all non-subscriber traffic. The value of this object is only meaningful if sapSubMgmtSubscriberLimit is set to 1.

OBJECT-TYPE

The value of sapSubMgmtNonSubTrafficSubProf specifies the subscriber profile applicable on this SAP for all non-subscriber traffic. The value of this object is only meaningful if sapSubMgmtSubscriberLimit is set to 1.

OBJECT-TYPE

The value of sapSubMgmtNonSubTrafficSlaProf specifies the SLA profile applicable on this SAP for all non-subscriber traffic. The value of this object is only meaningful if sapSubMgmtSubscriberLimit is set to 1.

OBJECT-TYPE

The value of sapSubMgmtMacDaHashing specifies whether subscriber traffic egressing a LAG SAP has its egress LAG link selected by a function of the MAC destination address instead of subscriber id. The value of this object is only meaningful if sapSubMgmtAdminStatus is set to 'enabled' and can only be configured for TLS services.

OBJECT-TYPE

The value of sapSubMgmtDefSubIdent specifies what is used as the default subscriber identification applicable on this SAP. This value is used in case no other source (like Radius) provides a subscriber identification string. If the value of this objects is set to 'useSapId', the SAP-id is used as the default subscriber identification string. In this case, sapSubMgmtDefSubIdentString must contain the empty string. If the value of this object is set to 'useString', the value of sapSubMgmtDefSubIdentString is used as the default subscriber identification string. In this case, an empty sapSubMgmtDefSubIdentString means that there is no default subscriber identification configured.

OBJECT-TYPE

The value of sapSubMgmtDefSubIdentString specifies the default subscriber identification string applicable on this SAP.

OBJECT-TYPE

The value of sapSubMgmtDefAppProfile specifies the default application profile applicable on this SAP. The corresponding profile is defined in TIMETRA-BSX-MIB::tmnxBsxAppProfTable.

OBJECT-TYPE

The value of sapSubMgmtNonSubTrafficAppProf specifies the application profile applicable on this SAP for all non-subscriber traffic. The value of this object is only meaningful if sapSubMgmtSubscriberLimit is set to 1.

OBJECT-TYPE

This table contains Multiple Spanning Tree Instance information for the SAP. Each management VPLS running MSTP can have upto 15 MSTI. An entry in this table is automatically created when a tlsMstiEntry is created.

OBJECT-TYPE

Information about a specific MSTI for a SAP.

OBJECT-TYPE

The value of the object sapTlsMstiPriority specifies the value of the port priority field which is contained in the most significant 4 bits of the 16-bit Port ID associated with this SAP and MSTI. As only the most significant 4 bits of the value are used, the actual value of this object is limited to multiples of 16: e.g. the agent rounds down the value to one of: 0, 16, 32, .. , 224, 240.

OBJECT-TYPE

The value of the object sapTlsMstiPathCost specifies the contribution of this port to the MSTI path cost of paths towards the spanning tree regional root which include this port.

OBJECT-TYPE

The value of the object sapTlsMstiLastMgmtChange indicates the value of sysUpTime at the time of the most recent management-initiated change to this SAP MSTI information.

OBJECT-TYPE

sapTlsMstiPortRole indicates the current role of the sap in the MSTI as defined by the Spanning Tree Protocol.

OBJECT-TYPE

The value of the object sapTlsMstiPortState indicates the port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning it will place that port into the 'broken' state.

OBJECT-TYPE

The value of the object sapTlsMstiDesignatedBridge indicates the Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment for this MSTI.

OBJECT-TYPE

The value of the object sapTlsMstiDesignatedPort indicates the Port Identifier of the port on the Designated Bridge for this port's segment for this MSTI.

OBJECT-TYPE

A table that contains IPIPE specific SAP information.

OBJECT-TYPE

IPIPE specific information about a SAP.

OBJECT-TYPE

The value of the object sapIpipeCeInetAddressType specifies the addresstype of the local end host IP of an IPIPE.

OBJECT-TYPE

The type of this address is determined by the value of the sapIpipeCeInetAddressType object. This object specifies the IPv4 address of the local end host of an IPIPE.

OBJECT-TYPE

The value of sapIpipeMacRefreshInterval specifies the interval between successive attempts to refresh the MAC address of the CE device associated with an Ethernet ipipe SAP. If no other event (such as reception of an ARP request from the CE) occurs that would refresh the MAC address before the end of the interval, an ARP request will be originated from the IPIPE SAP.

OBJECT-TYPE

The value of the object sapIpipeMacAddress specifies the MAC address of an IPIPE Ethernet SAP.

OBJECT-TYPE

The value of the object sapIpipeArpedMacAddress indicates the MAC address of the local end host.

OBJECT-TYPE

The value of the object sapIpipeArpedMacAddressTimeout indicates the number of seconds to wait for the sapIpipeArpedMacAddress to be re-refreshed.

OBJECT-TYPE

This table contains information on configurable objects on SAP level, that can be modified by a scheduled policy.

OBJECT-TYPE

Information about ToD policy modifiable config data for a SAP.

OBJECT-TYPE

The value of the object sapCurrentIngressIpFilterId indicates the index in the tIPFilterTable corresponding to the ingress filter applied on this SAP, or zero if no filter is currently active. The active filter may deviate from sapIngressIpFilterId in case it is overruled by a ToD Suite policy.

OBJECT-TYPE

The value of the object sapCurrentIngressIpv6FilterId indicates the index in the tIPv6FilterTable corresponding to the ingress Ipv6 filter applied on this SAP, or zero if no filter is currently active. The active filter may deviate from sapIngressIpv6FilterId in case it is overruled by a ToD Suite policy.

OBJECT-TYPE

The value of the object sapCurrentIngressMacFilterId indicates the index in the tMacFilterTable corresponding to the ingress Mac filter applied on this SAP, or zero if no filter is currently active. The active filter may deviate from sapIngressMacFilterId in case it is overruled by a ToD Suite policy.

OBJECT-TYPE

The value of the object sapCurrentIngressQosPolicyId indicates the index in the tSapIngressTable corresponding to the ingress Qos Policy applied on this SAP, or zero if no filter is currently active. The active filter may deviate from sapIngressQosPolicyId in case it is overruled by a ToD Suite policy.

OBJECT-TYPE

The value of the object sapCurrentIngressQosSchedPlcy indicates the ingress QoS scheduler on this SAP, or zero if none is currently active. The active policy may deviate from sapIngressQosSchedulerPolicy in case it is overruled by a ToD Suite policy defined on this SAP, or on the multi-service this SAP belongs to.

OBJECT-TYPE

The value of the object sapCurrentEgressIpFilterId indicates the index in the tIPFilterTable corresponding to the Egress filter applied on this SAP, or zero if no filter is currently active. The active filter may deviate from sapEgressIpFilterId in case it is overruled by a ToD Suite policy.

OBJECT-TYPE

The value of the object sapCurrentEgressIpv6FilterId indicates the index in the tIPv6FilterTable corresponding to the Egress Ipv6 filter applied on this SAP, or zero if no filter is currently active. The active filter may deviate from sapEgressIpv6FilterId in case it is overruled by a ToD Suite policy.

OBJECT-TYPE

The value of the object sapCurrentEgressMacFilterId indicates the index in the tMacFilterTable corresponding to the Egress Mac filter applied on this SAP, or zero if no filter is currently active. The active filter may deviate from sapEgressMacFilterId in case it is overruled by a ToD Suite policy.

OBJECT-TYPE

The value of the object sapCurrentEgressQosPolicyId indicates the index in the tSapEgressTable corresponding to the Egress Qos Policy applied on this SAP, or zero if no filter is currently active. The active filter may deviate from sapEgressQosPolicyId in case it is overruled by a ToD Suite policy.

OBJECT-TYPE

The value of the object sapCurrentEgressQosSchedPlcy indicates the Egress QoS scheduler on this SAP, or zero if none is currently active. The active policy may deviate from sapEgressQosSchedulerPolicy in case it is overruled by a ToD Suite policy defined on this SAP, or on the multi-customer this SAP belongs to.

OBJECT-TYPE

The value of the object sapIntendedIngressIpFilterId indicates the index in the tIPFilterTable corresponding to the ingress IP filter that should be applied on this SAP. If it deviates from sapCurrentIngressIpFilterId, this means that there was a problem when trying to activate this filter. It can only deviate when using ToD Suites for the SAP. When the ToD Suites decides that a new filter must be applied, it will try to do this. If it fails, the current and intended field are not equal.

OBJECT-TYPE

The value of the object sapIntendedIngressIpv6FilterId indicates the index in the tIPv6FilterTable corresponding to the ingress Ipv6 filter that should be applied on this SAP. If it deviates from sapCurrentIngressIpv6FilterId, this means that there was a problem when trying to activate this filter. It can only deviate when using ToD Suites for the SAP. When the ToD Suites decides that a new filter must be applied, it will try to do this. If it fails, the current and intended field are not equal.

OBJECT-TYPE

The value of the object sapIntendedIngressMacFilterId indicates the index in the tMacFilterTable corresponding to the ingress Mac filter that should be applied on this SAP. If it deviates from sapCurrentIngressMacFilterId, this means that there was a problem when trying to activate this filter. It can only deviate when using ToD Suites for the SAP. When the ToD Suites decides that a new filter must be applied, it will try to do this. If it fails, the current and intended field are not equal.

OBJECT-TYPE

The value of the object sapIntendedIngressQosPolicyId indicates the index in the tSapIngressTable corresponding to the ingress Qos policy that should be applied on this SAP. If it deviates from sapCurrentIngressQosPolicyId, this means that there was a problem when trying to activate this filter. It can only deviate when using ToD Suites for the SAP. When the ToD Suites decides that a new filter must be applied, it will try to do this. If it fails, the current and intended field are not equal.

OBJECT-TYPE

The value of the object sapIntendedIngressQosSchedPlcy indicates the ingress QoS scheduler that should be applied on this SAP. If it deviates from sapCurrentIngressQosSchedPlcy, this means that there was a problem when trying to activate this filter. It can only deviate when using ToD Suites for the SAP. When the ToD Suites decides that a new filter must be applied, it will try to do this. If it fails, the current and intended field are not equal.

OBJECT-TYPE

The value of the object sapIntendedEgressIpFilterId indicates the index in the tIPFilterTable corresponding to the Egress IP filter scheduler that should be applied on this SAP. If it deviates from sapCurrentEgressIpFilterId, this means that there was a problem when trying to activate this filter. It can only deviate when using ToD Suites for the SAP. When the ToD Suites decides that a new filter must be applied, it will try to do this. If it fails, the current and intended field are not equal.

OBJECT-TYPE

The value of the object sapIntendedEgressIpv6FilterId indicates the index in the tIPv6FilterTable corresponding to the Egress IPv6 filter scheduler that should be applied on this SAP. If it deviates from sapCurrentEgressIpv6FilterId, this means that there was a problem when trying to activate this filter. It can only deviate when using ToD Suites for the SAP. When the ToD Suites decides that a new filter must be applied, it will try to do this. If it fails, the current and intended field are not equal.

OBJECT-TYPE

The value of the object sapIntendedEgressMacFilterId indicates the index in the tMacFilterTable corresponding to the Egress mac filter scheduler that should be applied on this SAP. If it deviates from sapCurrentEgressMacFilterId, this means that there was a problem when trying to activate this filter. It can only deviate when using ToD Suites for the SAP. When the ToD Suites decides that a new filter must be applied, it will try to do this. If it fails, the current and intended field are not equal.

OBJECT-TYPE

The value of the object sapIntendedEgressQosPolicyId indicates the index in the tSapEgressTable corresponding to the Egress Qos Policy that should be applied on this SAP. If it deviates from sapCurrentEgressQosPolicyId, this means that there was a problem when trying to activate this filter. It can only deviate when using ToD Suites for the SAP. When the ToD Suites decides that a new filter must be applied, it will try to do this. If it fails, the current and intended field are not equal.

OBJECT-TYPE

The value of the object sapIntendedEgressQosSchedPlcy indicates the index in the tSapEgressTable corresponding to the Egress Qos Scheduler policy that should be applied on this SAP. If it deviates from sapCurrentEgressQosSchedPlcy, this means that there was a problem when trying to activate this filter. It can only deviate when using ToD Suites for the SAP. When the ToD Suites decides that a new filter must be applied, it will try to do this. If it fails, the current and intended field are not equal.

OBJECT-TYPE

A table that contains Ingress Qos policy related statistics for a SAP.

OBJECT-TYPE

Statistics about a specific Ingress Qos Policy applied on a specific SAP.

OBJECT-TYPE

The value of the object sapIgQosPlcyId indicates the row index in the tSapIngressTable corresponding to this ingress QoS policy, or one if no policy is specified.

OBJECT-TYPE

The value of the object sapIgQosPlcyDroppedHiPrioPackets indicates the number of high priority packets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The value of the object sapIgQosPlcyDroppedHiPrioOctets indicates the number of high priority octets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The value of the object sapIgQosPlcyDroppedLoPrioPackets indicates the number of low priority packets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The value of the object sapIgQosPlcyDroppedLoPrioOctets indicates the number of low priority octets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The value of the object sapIgQosPlcyForwardedInProfPackets indicates the number of in-profile packets (rate below CIR) forwarded by the ingress Qchip.

OBJECT-TYPE

The value of the object sapIgQosPlcyForwardedInProfOctets indicates the number of in-profile octets (rate below CIR) forwarded by the ingress Qchip.

OBJECT-TYPE

The value of the object sapIgQosPlcyForwardedOutProfPackets indicates the number of out-of-profile packets (rate above CIR) forwarded by the ingress Qchip.

OBJECT-TYPE

The value of the object sapIgQosPlcyForwardedOutProfOctets indicates the number of out-of-profile octets (rate above CIR) forwarded by the ingress Qchip.

OBJECT-TYPE

A table that contains Egress Qos policy related statistics for a SAP.

OBJECT-TYPE

Statistics about a specific Egress Qos Policy applied on a specific SAP.

OBJECT-TYPE

The value of the object sapEgQosPlcyId indicates the row index in the tSapEgressTable corresponding to this egress QoS policy, or one if no policy is specified.

OBJECT-TYPE

The value of the object sapEgQosPlcyDroppedInProfPackets indicates the number of in-profile packets, as determined by the SAP egress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The value of the object sapEgQosPlcyDroppedInProfOctets indicates the number of in-profile octets, as determined by the SAP egress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The value of the object sapEgQosPlcyDroppedOutProfPackets indicates the number of out-profile packets, as determined by the SAP egress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The value of the object sapEgQosPlcyDroppedOutProfOctets indicates the number of out-profile octets, as determined by the SAP egress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The value of the object sapEgQosPlcyForwardedInProfPackets indicates the number of in-profile packets (rate below CIR) forwarded by the egress Qchip.

OBJECT-TYPE

The value of the object sapEgQosPlcyForwardedInProfOctets indicates the number of in-profile octets (rate below CIR) forwarded by the egress Qchip.

OBJECT-TYPE

The value of the object sapEgQosPlcyForwardedOutProfPackets indicates the number of out-of-profile packets (rate above CIR) forwarded by the egress Qchip.

OBJECT-TYPE

The value of the object sapEgQosPlcyForwardedOutProfOctets indicates the number of out-of-profile octets (rate above CIR) forwarded by the egress Qchip.

OBJECT-TYPE

A table that contains ingress QoS queue SAP statistics, per Ingress QoS Policy the queue was used by.

OBJECT-TYPE

Ingress statistics about a specific SAP's QoS queue for a given Qos policy.

OBJECT-TYPE

The value of the object sapIgQosPlcyQueuePlcyId indicates the row index in the tSapIngressTable corresponding to this ingress QoS policy.

OBJECT-TYPE

The index of the ingress QoS queue of this SAP used by the policy indicated by sapIgQosPlcyQueuePlcyId.

OBJECT-TYPE

The value of sapIgQosPlcyQueueStatsOfferedHiPrioPackets indicates the number of high priority packets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip.

OBJECT-TYPE

The value of sapIgQosPlcyQueueStatsDroppedHiPrioPackets indicates the number of high priority packets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The value of sapIgQosPlcyQueueStatsOfferedLoPrioPackets indicates the number of low priority packets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip.

OBJECT-TYPE

The value of sapIgQosPlcyQueueStatsDroppedLoPrioPackets indicates the number of low priority packets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The value of sapIgQosPlcyQueueStatsOfferedHiPrioOctets indicates the number of high priority octets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip.

OBJECT-TYPE

The value of sapIgQosPlcyQueueStatsDroppedHiPrioOctets indicates the number ofhigh priority octets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The value of sapIgQosPlcyQueueStatsOfferedLoPrioOctets indicates the number of low priority octets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip.

OBJECT-TYPE

The value of sapIgQosPlcyQueueStatsDroppedLoPrioOctets indicates the number of low priority octets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The value of sapIgQosPlcyQueueStatsForwardedInProfPackets indicates the number of in-profile packets (rate below CIR) forwarded by the ingress Qchip.

OBJECT-TYPE

The value of sapIgQosPlcyQueueStatsForwardedOutProfPackets indicates the number of out-of-profile packets (rate above CIR) forwarded by the ingress Qchip.

OBJECT-TYPE

The value of sapIgQosPlcyQueueStatsForwardedInProfOctets indicates the number of in-profile octets (rate below CIR) forwarded by the ingress Qchip.

OBJECT-TYPE

The value of sapIgQosPlcyQueueStatsForwardedOutProfOctets indicates the number of out-of-profile octets (rate above CIR) forwarded by the ingress Qchip.

OBJECT-TYPE

The value of the object sapIgQosPlcyQueueCustId indicates the Customer ID for the associated service.

OBJECT-TYPE

The value of sapIgQosPlcyQueueStatsUncoloredPacketsOffered indicates the number of uncolored packets offered to the ingress Qchip.

OBJECT-TYPE

The value of sapIgQosPlcyQueueStatsUncoloredOctetsOffered indicates the number of uncolored octets offered to the ingress Qchip.

OBJECT-TYPE

A table that contains egress QoS queue SAP statistics per Egress QoS Policy the queue was used by.

OBJECT-TYPE

Egress statistics about a specific SAP's QoS queue for a given Qos policy.

OBJECT-TYPE

The row index in the tSapEgressTable corresponding to this egress QoS policy.

OBJECT-TYPE

The value of sapEgQosPlcyQueueId indicates index of the egress QoS queue of this SAP.

OBJECT-TYPE

The value of sapEgQosPlcyQueueStatsForwardedInProfPackets indicates the number of in-profile packets (rate below CIR) forwarded by the egress Qchip.

OBJECT-TYPE

The value of sapEgQosPlcyQueueStatsDroppedInProfPackets indicates the number of in-profile packets discarded by the egress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The value of sapEgQosPlcyQueueStatsForwardedOutProfPackets indicates the number of out-of-profile packets (rate above CIR) forwarded by the egress Qchip.

OBJECT-TYPE

The value of sapEgQosPlcyQueueStatsDroppedOutProfPackets indicates the number out-of-profile packets discarded by the egress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The value of sapEgQosPlcyQueueStatsForwardedInProfOctets indicates the number ofin-profile octets (rate below CIR) forwarded by the egress Qchip.

OBJECT-TYPE

The value of sapEgQosPlcyQueueStatsDroppedInProfOctets indicates the number in-profile octets discarded by the egress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The value of sapEgQosPlcyQueueStatsForwardedOutProfOctets indicates the number of out-of-profile octets (rate above CIR) forwarded by the egress Qchip.

OBJECT-TYPE

The value of sapEgQosPlcyQueueStatsDroppedOutProfOctets indicates the number out-of-profile octets discarded by the egress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

OBJECT-TYPE

The value of the object sapEgQosPlcyQueueCustId indicates the Customer ID for the associated service.

OBJECT-TYPE

sapDhcpInfoTable contains DHCP information related to a routed CO subscriber SAP. This table complements sapBaseInfoTable, and contains an entry for each routed CO subscriber SAP. Rows in this table are created and deleted automatically by the system.

OBJECT-TYPE

DHCP specific information for a routed CO subscriber SAP.

OBJECT-TYPE

The value of the object sapDhcpOperLeasePopulate indicates the number of DHCP lease states currently allocated on this SAP.

OBJECT-TYPE

A table that contains ingress QoS queue statistics for the SAP's, organized by scheduler policy.

OBJECT-TYPE

Statistics about a specific SAP's ingress Qos Scheduler. Entries are created when a scheduler policy of a SAP is replaced with another one due to Time-Of-Day policies.

OBJECT-TYPE

The number of forwarded packets, as determined by the SAP ingress scheduler policy, offered by the Pchip to the Qchip.

OBJECT-TYPE

The number of forwarded octets, as determined by the SAP ingress scheduler policy, offered by the Pchip to the Qchip.

OBJECT-TYPE

A table that contains egress QoS scheduler statistics for the SAP's, organized by scheduler policy.

OBJECT-TYPE

Statistics about a specific SAP's egress QoS scheduler. Entries are created when a scheduler policy of a SAP is replaced with another one due to Time-Of-Day policies.

OBJECT-TYPE

The number of packets forwarded by the egress Qchip, as determined by the SAP egress scheduler policy.

OBJECT-TYPE

The number of octets forwarded by the egress Qchip, as determined by the SAP egress scheduler policy.

OBJECT-TYPE

The sapIngSchedPlcyPortStatsTable contains ingress QoS scheduler statistics for the SAP's, organized per scheduler policy and per port. This table is used when the SAP is a CCAG or LAG in 'link' mode, or an APS. Entries are created when a scheduler policy of a SAP is replaced with another one due to Time-Of-Day policies.

OBJECT-TYPE

Statistics about a specific SAP's ingress Qos Scheduler. Entries are created when a scheduler policy of a SAP is replaced with another one due to Time-Of-Day policies.

OBJECT-TYPE

The value of sapIngSchedPlcyPortStatsPort is used as an index of the ingress QoS scheduler of this SAP. When the SAP is an aps/ccag/lag in 'link' mode, this object is the TmnxPortID of the member-port on which the scheduler is applied.

OBJECT-TYPE

The value of sapIngSchedPlcyPortStatsFwdPkt indicates the number of forwarded packets, as determined by the SAP ingress scheduler policy, offered by the Pchip to the Qchip.

OBJECT-TYPE

The value of sapIngSchedPlcyPortStatsFwdOct indicates the number of forwarded octets,as determined by the SAP ingress scheduler policy, offered by the Pchip to the Qchip.

OBJECT-TYPE

The sapEgrSchedPlcyPortStatsTable contains egress QoS scheduler statistics for the SAP's, organized per scheduler policy and per port. This table is used when the SAP is a CCAG or LAG in 'link' mode, or an APS. Entries are created when a scheduler policy of a SAP is replaced with another one due to Time-Of-Day policies.

OBJECT-TYPE

Statistics about a specific SAP's egress Qos Scheduler. Entries are created when a scheduler policy of a SAP is replaced with another one due to Time-Of-Day policies.

OBJECT-TYPE

The value of sapEgrSchedPlcyPortStatsPort is used as an index of the egress QoS scheduler of this SAP. When the SAP is an aps/ccag/lag in 'link' mode, this object is the TmnxPortID of the member-port on which the scheduler is applied.

OBJECT-TYPE

The value of sapEgrSchedPlcyPortStatsFwdPkt indicates the number of forwarded packets, as determined by the SAP egress scheduler policy, offered by the Pchip to the Qchip.

OBJECT-TYPE

The value of sapEgrSchedPlcyPortStatsFwdOct indicates the number of forwarded octets,as determined by the SAP egress scheduler policy, offered by the Pchip to the Qchip.

OBJECT-TYPE

A table that contains CEM SAP information.

OBJECT-TYPE

Information about a specific CEM SAP.

OBJECT-TYPE

The value of the object sapCemLastMgmtChange indicates the value of sysUpTime at the time of the most recent management-initiated change to this CEM SAP information.

OBJECT-TYPE

This object indicates the CEM SAP endpoint type.

OBJECT-TYPE

This object indicates the bit-rate in multiples of 64 Kbit/s of the CEM SAP.

OBJECT-TYPE

This object indicates the CAS trunk framing mode of the CEM SAP.

OBJECT-TYPE

This object specifies the payload size (in bytes) of packets transmitted to the Packet Service Network (PSN) by the CEM SAP. This determines the size of the data that will be transmitted over the service. As well, if the size of the data received is not consistent with the payload size then the packet is considered malformed. Default value depends on the CEM SAP endpoint type (sapCemEndpointType), and if applicable, the number of timeslots (sapCemBitrate): --------------------------------------------------------- | Endpoint Type | Timeslots | Default payload size | ---------------------+-----------+----------------------- | 'unstructuredE1' | n/a | 256 bytes | ---------------------+-----------+----------------------- | 'unstructuredT1' | n/a | 192 bytes | ---------------------+-----------+----------------------- | 'unstructuredE3' | n/a | 1024 bytes | ---------------------+-----------+----------------------- | 'unstructuredT3' | n/a | 1024 bytes | ---------------------+-----------+----------------------- | 'nxDS0' (E1/T1) | N = 1 | 64 bytes | | +-----------+----------------------- | | N = 2..4 | N x 32 bytes | | +-----------+----------------------- | | N = 5..15 | N x 16 bytes | | +-----------+----------------------- | | N >= 16 | N x 8 bytes | ---------------------+-----------+----------------------- | 'nxDS0WithCas' (E1)| N | N x 16 bytes | ---------------------+-----------+----------------------- | 'nxDS0WithCas' (T1)| N | N x 24 bytes | --------------------------------------------------------- For all endpoint types except for 'nxDS0WithCas', valid payload size range is from the default (in the table above) to 2048 bytes. For 'nxDS0WithCas', sapCemPayloadSize divide by the number of timeslots (sapCemBitrate) must be an integer factor of the number of frames per trunk multiframe (i.e. 16 for E1 trunk and 24 for T1 trunk). For '1xDS0', sapCemPayloadSize must be a multiple of 2. For 'NxDS0', where N > 1, sapCemPayloadSize must be a multiple of the number of timeslots (sapCemBitrate). For 'unstructuredE1', 'unstructuredT1', 'unstructuredE3' and 'unstructuredT3', sapCemPayloadSize must be a multiple of 32 bytes. Configuring sapCemPayloadSize and sapCemJitterBuffer to values that result in less than 2 packet buffers or greater than 32 packet buffer is not allowed. Setting this object to 0 sets it back to the default value.

OBJECT-TYPE

This object specifies the jitter buffer size in milliseconds (ms). Default value depends on the CEM SAP endpoint type (sapCemEndpointType), and if applicable, the number of timeslots (sapCemBitrate): --------------------------------------------------------- | Endpoint Type | Timeslots | Default jitter buf. | ---------------------+-----------+----------------------- | 'unstructuredE1' | n/a | 5 ms | ---------------------+-----------+----------------------- | 'unstructuredT1' | n/a | 5 ms | ---------------------+-----------+----------------------- | 'unstructuredE3' | n/a | 5 ms | ---------------------+-----------+----------------------- | 'unstructuredT3' | n/a | 5 ms | ---------------------+-----------+----------------------- | 'nxDS0' (E1/T1) | N = 1 | 32 ms | | +-----------+----------------------- | | N = 2..4 | 16 ms | | +-----------+----------------------- | | N = 5..15 | 8 ms | | +-----------+----------------------- | | N >= 16 | 5 ms | ---------------------+-----------+----------------------- | 'nxDS0WithCas' (E1)| N | 8 ms | ---------------------+-----------+----------------------- | 'nxDS0WithCas' (T1)| N | 12 ms | --------------------------------------------------------- Configuring sapCemPayloadSize and sapCemJitterBuffer to values that result in less than 2 packet buffers or greater than 32 packet buffers is not allowed. The valid range is 1 to 250 ms. Setting this object to 0 sets it back to the default value.

OBJECT-TYPE

This object specifies whether a RTP header is used when packets are transmitted to the Packet Service Network (PSN) by the CEM SAP.

OBJECT-TYPE

This object specifies whether this CEM SAP is in differential mode.

OBJECT-TYPE

This object specifies whether the value of the timestamp frequency in multiples of 8 KHz for this CEM SAP.

OBJECT-TYPE

The value of sapCemReportAlarm determines when and if to generate notifications for the CEM SAP.

OBJECT-TYPE

The value of sapCemReportAlarmStatus indicates the current alarms on this CEM SAP.

OBJECT-TYPE

The value of the object sapCemLocalEcid specifies the local ECID. Only valid if CEM SAP belongs to an EPIPE service.

OBJECT-TYPE

The value of the object sapCemRemoteMacAddr specifies the remote MAC address. Only valid if CEM SAP belongs to an EPIPE service.

OBJECT-TYPE

The value of the object sapCemRemoteEcid specifies the remote ECID. Only valid if CEM SAP belongs to an EPIPE service.

OBJECT-TYPE

A table that contains CEM SAP statistics.

OBJECT-TYPE

Statistics for a specific CEM SAP.

OBJECT-TYPE

The value of sapCemStatsIngressForwardedPkts indicates the number of packets that were successfully forwarded.

OBJECT-TYPE

The value of sapCemStatsIngressDroppedPkts indicates the total number of packets that were dropped due to errors.

OBJECT-TYPE

The value of sapCemStatsEgressForwardedPkts indicates the number of packets that were successfully forwarded.

OBJECT-TYPE

The value of sapCemStatsEgressDroppedPkts indicates the total number of packets that were dropped due to errors.

OBJECT-TYPE

The value of sapCemStatsEgressMissingPkts indicates the number of missing packets (as detected via control word sequence number gaps).

OBJECT-TYPE

The value of sapCemStatsEgressPktsReOrder indicates the number of packets detected out of sequence (via control word sequence number), but successfully re-ordered.

OBJECT-TYPE

The value of sapCemStatsEgressJtrBfrUnderruns indicates the number of times a packet needed to be played out and the jitter buffer was empty.

OBJECT-TYPE

The value of sapCemStatsEgressJtrBfrOverruns indicates the number of times a packet was dropped because it could not fit in the jitter buffer.

OBJECT-TYPE

The value of sapCemStatsEgressMisOrderDropped indicates the number of packets detected out of order (via control word sequence numbers), and could not be re-ordered, or could not be placed in the jitter buffer because it was out of the current window.

OBJECT-TYPE

The value of sapCemStatsEgressMalformedPkts indicates the number of packets detected with unexpected size, or bad headers' stack.

OBJECT-TYPE

The value of sapCemStatsEgressLBitDropped indicates the number of packets dropped due to the L bit set by the far end.

OBJECT-TYPE

The value of sapCemStatsEgressMultipleDropped indicates the number of packets dropped due to multiple sequence numbers.

OBJECT-TYPE

The value of sapCemStatsEgressESs indicates the number of Error Seconds (ESs) encountered. Any malformed packet, seq. error, LOPS and similar are considered as error seconds.

OBJECT-TYPE

The value of sapCemStatsEgressSESs indicates the number of Severely Error Seconds (SESs) encountered. This is when more than 30 percent of the packets within a one second window are missing.

OBJECT-TYPE

The value of sapCemStatsEgressUASs indicates the number of Unavailable Seconds (UASs) encountered. Any consecutive ten seconds of SESs are counted as one UAS.

OBJECT-TYPE

The value of sapCemStatsEgressFailureCounts indicates the number failure events. A failure event begins when the LOPS failure is declared, and ends when the failure is cleared.

OBJECT-TYPE

The value of sapCemStatsEgressUnderrunCounts indicates the number of times the jitter buffer went into an underrun state.

OBJECT-TYPE

The value of sapCemStatsEgressOverrunCounts indicates the number of times the jitter buffer went into an overrun state.

OBJECT-TYPE

A table that contains SAP Layer 2 Protocol Tunneling Statistics. This table complements sapTlsInfoTable. Rows in this table are created and deleted automatically by the system.

OBJECT-TYPE

Layer 2 Protocol Tunneling Statistics for a specific SAP. The statistics are provided for each combination of Destination Address and LLC SNAP type.

OBJECT-TYPE

The value of sapTlsL2ptStatsLastClearedTime indicates the last time that these stats were cleared. The value zero indicates that they have not been cleared yet.

OBJECT-TYPE

The value of sapTlsL2ptStatsL2ptEncapStpConfigBpdusRx indicates the number of L2PT encapsulated STP config bpdus received on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsL2ptEncapStpConfigBpdusTx indicates the number of L2PT encapsulated STP config bpdus transmitted on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsL2ptEncapStpRstBpdusRx indicates the number of L2PT encapsulated STP rst bpdus received on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsL2ptEncapStpRstBpdusTx indicates the number of L2PT encapsulated STP rst bpdus transmitted on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsL2ptEncapStpTcnBpdusRx indicates the number of L2PT encapsulated STP tcn bpdus received on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsL2ptEncapStpTcnBpdusTx indicates the number of L2PT encapsulated STP tcn bpdus transmitted on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsL2ptEncapPvstConfigBpdusRx indicates the number of L2PT encapsulated PVST config bpdus received on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsL2ptEncapPvstConfigBpdusTx indicates the number of L2PT encapsulated PVST config bpdus transmitted on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsL2ptEncapPvstRstBpdusRx indicates the number of L2PT encapsulated PVST rst bpdus received on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsL2ptEncapPvstRstBpdusTx indicates the number of L2PT encapsulated PVST rst bpdus transmitted on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsL2ptEncapPvstTcnBpdusRx indicates the number of L2PT encapsulated PVST tcn bpdus received on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsL2ptEncapPvstTcnBpdusTx indicates the number of L2PT encapsulated PVST tcn bpdus transmitted on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsStpConfigBpdusRx indicates the number of STP config bpdus received on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsStpConfigBpdusTx indicates the number of STP config bpdus transmitted on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsStpRstBpdusRx indicates the number of STP rst bpdus received on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsStpRstBpdusTx indicates the number of STP rst bpdus transmitted on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsStpTcnBpdusRx indicates the number of STP tcn bpdus received on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsStpTcnBpdusTx indicates the number of STP tcn bpdus transmitted on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsPvstConfigBpdusRx indicates the number of PVST config bpdus received on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsPvstConfigBpdusTx indicates the number of PVST config bpdus transmitted on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsPvstRstBpdusRx indicates the number of PVST rst bpdus received on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsPvstRstBpdusTx indicates the number of PVST rst bpdus transmitted on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsPvstTcnBpdusRx indicates the number of PVST tcn bpdus received on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsPvstTcnBpdusTx indicates the number of PVST tcn bpdus transmitted on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsOtherBpdusRx indicates the number of other bpdus received on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsOtherBpdusTx indicates the number of other bpdus transmitted on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsOtherL2ptBpdusRx indicates the number of other L2PT bpdus received on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsOtherL2ptBpdusTx indicates the number of other L2PT bpdus transmitted on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsOtherInvalidBpdusRx indicates the number of other invalid bpdus received on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsOtherInvalidBpdusTx indicates the number of other invalid bpdus transmitted on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsL2ptEncapCdpBpdusRx indicates the number of L2PT encapsulated CDP bpdus received on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsL2ptEncapCdpBpdusTx indicates the number of L2PT encapsulated CDP bpdus transmitted on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsL2ptEncapVtpBpdusRx indicates the number of L2PT encapsulated VTP bpdus received on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsL2ptEncapVtpBpdusTx indicates the number of L2PT encapsulated VTP bpdus transmitted on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsL2ptEncapDtpBpdusRx indicates the number of L2PT encapsulated DTP bpdus received on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsL2ptEncapDtpBpdusTx indicates the number of L2PT encapsulated DTP bpdus transmitted on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsL2ptEncapPagpBpdusRx indicates the number of L2PT encapsulated PAGP bpdus received on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsL2ptEncapPagpBpdusTx indicates the number of L2PT encapsulated PAGP bpdus transmitted on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsL2ptEncapUdldBpdusRx indicates the number of L2PT encapsulated UDLD bpdus received on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsL2ptEncapUdldBpdusTx indicates the number of L2PT encapsulated UDLD bpdus transmitted on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsCdpBpdusRx indicates the number of CDP bpdus received on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsCdpBpdusTx indicates the number of CDP bpdus transmitted on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsVtpBpdusRx indicates the number of VTP bpdus received on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsVtpBpdusTx indicates the number of VTP bpdus transmitted on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsDtpBpdusRx indicates the number of DTP bpdus received on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsDtpBpdusTx indicates the number of DTP bpdus transmitted on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsPagpBpdusRx indicates the number of PAGP bpdus received on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsPagpBpdusTx indicates the number of PAGP bpdus transmitted on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsUdldBpdusRx indicates the number of UDLD bpdus received on this SAP.

OBJECT-TYPE

The value of sapTlsL2ptStatsUdldBpdusTx indicates the number of UDLD bpdus transmitted on this SAP.

OBJECT-TYPE

A table that contains Ethernet SAP information.

OBJECT-TYPE

Information about a specific Ethernet SAP.

OBJECT-TYPE

sapEthernetLLFAdminStatus specifies whether or not Link- Loss Forwarding is enabled ('up'). When this object is set to 'up' the underlying port will be forced into the operationally 'down' state if the service is operationally 'down', or any of the 'sdpBindPwPeerStatusBits' are set, and will set the underlying port's tmnxPortEtherReasonDownFlags 'linklossFwd' bit. Setting this object to 'down' will clear the 'linklossFwd' reason. sapEthernetLLFAdminStatus can only be enabled on saps configured for an EPIPE service using an Ethernet port with the tmnxPortEncapType set to 'nullEncap.'

OBJECT-TYPE

sapEthernetLLFOperStatus indicates whether or not the underlying port is forced operationally 'down' due to the service being operationally 'down' or an sdpBindPwPeerStatusBits bit is set. sapEthernetLLFOperStatus is set to 'fault' when the sapEthernetLLFAdminStatus is set to 'up,' and either a fault has occurred on the pseudo-wire, or the service is down, otherwise sapEthernetLLFOperStatus is set to 'clear.'

OBJECT-TYPE

The msapPlcyTable has an entry for each managed SAP(MSAP) policy configured in the system.

OBJECT-TYPE

Each entry represents the configuration for a managed SAP(MSAP) policy. The values for each entry will be used to populate the following tables when the MSAP policy is applied to a MSAP: ALCATEL-IND1-TIMETRA-SAP-MIB::sapBaseInfoTable ALCATEL-IND1-TIMETRA-SAP-MIB::sapSubMgmtInfoTable

OBJECT-TYPE

The value of msapPlcyName specifies the name of the MSAP policy.

OBJECT-TYPE

The value of msapPlcyRowStatus is used for the creation and deletion of MSAP policies.

OBJECT-TYPE

The value of msapPlcyLastChanged indicates the sysUpTime at the time of the last modification of this entry. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The value of msapPlcyDescription specifies the description of the MSAP policy.

OBJECT-TYPE

The value of msapPlcyCpmProtPolicyId specifies a CPM Protection policy for the MSAP policy. If a corresponding policy is not defined in TIMETRA-SECURITY-MIB::tmnxCpmProtPolTable, an 'inconsistentValue' error will be returned. A value of one specifies that the default CPM Protection policy is associated with the Managed SAP. This object is not supported on SR-1 and ESS-1, where the value of ALCATEL-IND1-TIMETRA-CHASSIS-MIB::tmnxChassisType is '5', and 7710, where the value of ALCATEL-IND1-TIMETRA-CHASSIS-MIB::tmnxChassisType is '7' or '9'. An attempt to set msapPlcyCpmProtPolicyId to a non-zero value on one of these unsupported chassis types will return an 'inconsistentValue' error.

OBJECT-TYPE

The value of msapPlcyCpmProtMonitorMac specifies whether the tmnxCpmProtPolPerSrcRateLimit of the CPM Protection policy, as specified by msapPlcyCpmProtPolicyId, must be applied. If the value of msapPlcyCpmProtMonitorMac is 'true', the per-source rate limit must be applied. If the value of msapPlcyCpmProtPolicyId is equal to zero, the value of msapPlcyCpmProtMonitorMac is irrelevant and will be ignored. This object is not supported on SR-1 and ESS-1, where the value of ALCATEL-IND1-TIMETRA-CHASSIS-MIB::tmnxChassisType is '5', and 7710, where the value of ALCATEL-IND1-TIMETRA-CHASSIS-MIB::tmnxChassisType is '7' or '9'. An attempt to set msapPlcyCpmProtMonitorMac to 'true' on one of these unsupported chassis types will return an 'inconsistentValue' error.

OBJECT-TYPE

The value of msapPlcySubMgmtDefSubId specifies what will be used as the default subscriber identification applicable on the MSAP. This value is used in case no other source (like Radius) provides a subscriber identification string. If the value of this object is set to 'useSapId', the SAP-id will be used as the default subscriber identification string. In this case, msapPlcySubMgmtDefSubIdStr must contain the empty string, so any non-empty string in msapPlcySubMgmtDefSubIdStr will be set to an empty string. If the value of this object is set to 'useString', the value of msapPlcySubMgmtDefSubIdStr will be used as the default subscriber identification string. In this case, an empty msapPlcySubMgmtDefSubIdStr means that there is no default subscriber identification configured.

OBJECT-TYPE

The value of msapPlcySubMgmtDefSubIdStr specifies the default subscriber identification string applicable on this MSAP.

OBJECT-TYPE

The value of msapPlcySubMgmtDefSubProfile specifies the default subscriber profile applicable on the MSAP. If a corresponding profile is not defined in tmnxSubProfileTable, an 'inconsistentValue' error will be returned. A value of 'default' is not allowed for this object.

OBJECT-TYPE

The value of msapPlcySubMgmtDefSlaProfile specifies the default SLA profile applicable on the MSAP. If a corresponding profile is not defined in tmnxSLAProfileTable, an 'inconsistentValue' error will be returned.

OBJECT-TYPE

The value of msapPlcySubMgmtDefAppProfile specifies the default application profile applicable on the MSAP. If a corresponding profile is not defined in TIMETRA-BSX-MIB::tmnxBsxAppProfTable, an 'inconsistentValue' error will be returned.

OBJECT-TYPE

The value of msapPlcySubMgmtSubIdPlcy specifies the subscriber identification policy applicable on the MSAP. If a corresponding profile is not defined in tmnxSubIdentPolicyTable, an 'inconsistentValue' error will be returned.

OBJECT-TYPE

The value of msapPlcySubMgmtSubscriberLimit specifies the maximum number of subscribers allowed for the MSAP. A value is 0 means there is no limit. The values for the objects msapPlcySubMgmtProfiledTrafOnly, msapPlcySubMgmtNonSubTrafSubProf, and msapPlcySubMgmtNonSubTrafSlaProf are only meaningful when the value of msapPlcySubMgmtSubscriberLimit is 1 and will not be used when the value of msapPlcySubMgmtSubscriberLimit is not 1.

OBJECT-TYPE

The value of msapPlcySubMgmtProfiledTrafOnly specifies whether only profiled traffic is applicable for the MSAP. If set to 'true', the MSAP queues will be deleted. The value of this object is only meaningful if msapPlcySubMgmtSubscriberLimit is set to 1.

OBJECT-TYPE

The value of msapPlcySubMgmtNonSubTrafSubId specifies the subscriber identification applicable on the MSAP for all non-subscriber traffic. The value of this object is only meaningful if msapPlcySubMgmtSubscriberLimit is set to 1.

OBJECT-TYPE

The value of msapPlcySubMgmtNonSubTrafSubProf specifies the subscriber profile applicable on the MSAP for all non-subscriber traffic. The value of this object is only meaningful if msapPlcySubMgmtSubscriberLimit is set to 1.

OBJECT-TYPE

The value of msapPlcySubMgmtNonSubTrafSlaProf specifies the SLA profile applicable on the MSAP for all non-subscriber traffic. The value of this object is only meaningful if msapPlcySubMgmtSubscriberLimit is set to 1.

OBJECT-TYPE

The value of msapPlcySubMgmtNonSubTrafAppProf specifies the Application profile applicable on the MSAP for all non-subscriber traffic. The value of this object is only meaningful if msapPlcySubMgmtSubscriberLimit is set to 1.

OBJECT-TYPE

The value of msapPlcyAssociatedMsaps indicates the number of MSAPs associated with this MSAP policy.

OBJECT-TYPE

The msapTlsPlcyTable has an entry for each managed SAP (MSAP) policy configured in the system.

OBJECT-TYPE

Each entry represents the VPLS-related configuration for a managed SAP (MSAP) policy. The values for each entry will be used to populate the following VPLS-related tables when the MSAP policy is applied to a MSAP: TIMETRA-SAP-MIB::sapTlsInfoTable TIMETRA-SAP-MIB::sapTlsDhcpInfoTable ALCATEL-IGMP-SNOOPING-MIB::tlsIgmpSnpgConfigTable

OBJECT-TYPE

The value of msapTlsPlcyLastChanged indicates the sysUpTime at the time of the last modification of this entry. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The value of msapTlsPlcySplitHorizonGrp specifies the name of the split-horizon group for the MSAP. If the name specified does not correspond to a tlsShgInfoEntry for the VPLS service, the creation of the MSAP will fail. Additionally, if msapTlsPlcySplitHorizonGrp is set to a new value, the sapSplitHorizonGrp object for any existing MSAPs created by this policy will not be updated.

OBJECT-TYPE

The value of msapTlsPlcyArpReplyAgent specifies the status of the special ARP response mechanism in the system for ARP requests destined to static or dynamic hosts associated with the MSAP. 'disabled' - the ARP reply function is not operational 'enabled' - the ARP reply function is enabled without subscriber identification. 'enabledWithSubscrIdent' - the ARP reply function is enabled with subscriber identification.

OBJECT-TYPE

The value of msapTlsPlcySubMgmtMacDaHashing specifies whether subscriber traffic egressing a LAG MSAP has its egress LAG link selected by a function of the MAC destination address instead of subscriber id.

OBJECT-TYPE

The value of msapTlsPlcyDhcpLeasePopulate specifies the maximum number of DHCP lease states allowed on the MSAP.

OBJECT-TYPE

The value of msapTlsPlcyDhcpPrxyAdminState specifies the desired administrative state of the proxy server on the interface.

OBJECT-TYPE

The value of msapTlsPlcyDhcpPrxyServAddrType specifies the address type of msapTlsPlcyDhcpPrxyServAddr.

OBJECT-TYPE

The value of msapTlsPlcyDhcpPrxyServAddr specifies the IP address of the which will be used as the source address of the emulated DHCP server in the context of the VPLS MSAP. This address is mandatory for the proxy server capability and it should be in the context of the subnet represented by the VPLS.

OBJECT-TYPE

The value of msapTlsPlcyDhcpPrxyLeaseTime specifies, in seconds, how long a DHCP client is allowed to use the offered IP address. A value of 0 means the lease time provided by a RADIUS or an upstream DHCP server will not be overridden. A value of 7 days (315446399 seconds) is used when RADIUS does not provide a lease time.

OBJECT-TYPE

The value of msapTlsPlcyDhcpPrxyLTRadOverride specifies whether or not the lease time provided by the RADIUS server is presented to the DHCP client. By default the proxy-server will always make use of msapTlsPlcyDhcpPrxyLeaseTime, regardless of what lease time information is provided from the RADIUS server. When msapTlsPlcyDhcpPrxyLTRadOverride is set to 'true', the proxy-server will use the lease time information provided by the RADIUS server, regardless of the configured lease time.

OBJECT-TYPE

The value of msapTlsPlcyDhcpInfoAction specifies the DHCP option reforwarding policy: 'replace' - replace existing information with configured information 'drop' - discard messages with existing relay information if the option-82 information is also present 'keep' - retain the existing relay information

OBJECT-TYPE

The value of msapTlsPlcyDhcpCircuitId specifies whether or not the circuit-id suboption is present, and if it is present what information goes in it: none - the circuit-id suboption will not be part of the information option (Option 82). asciiTuple - the ASCII-encoded concatenated tuple consisting of the - access-node-identifier - service-id - interface-name is used. vlanAsciiTuple - the format will include VLAN-id and dot1p bits in addition to what is included in ascii-tuple already. The format is supported on dot1q and qinq encapsulated ports only. Thus, when the option 82 bits are stripped, dot1p bits will be copied to the Ethernet header of an outgoing packet.

OBJECT-TYPE

The value of msapTlsPlcyDhcpRemoteId specifies what information goes into the remote-id suboption in the DHCP Relay packet. If the value of this object is set to 'none', the remote-id suboption will not be part of the information option (Option 82). If the value of this object is set to 'mac', the MAC address of the remote end is encoded in the suboption. If the value of this object is set to 'remote-id', msapTlsPlcyDhcpRemoteIdString will represent the remote-id. By default, the remote-id value is none.

OBJECT-TYPE

The value of msapTlsPlcyDhcpRemoteIdString specifies the remote-id. The value of this object is ignored if msapTlsPlcyDhcpRemoteId does not have the value of 'remote-id'.

OBJECT-TYPE

The value of msapTlsPlcyDhcpVendorInclOpts specifies what is encoded in the Alcatel-Lucent vendor specific sub-option of option 82. The value of this object is only used when msapTlsPlcyDhcpInfoAction is 'replace'.

OBJECT-TYPE

The value of msapTlsPlcyDhcpVendorOptStr specifies the string that goes into the Alcatel-Lucent vendor specific sub-option of option 82. This string is only used when msapTlsPlcyDhcpInfoAction is set to 'replace'.

OBJECT-TYPE

The value of msapTlsPlcyEgressMcastGroup specifies the Egress Multicast Group for the MSAP.

OBJECT-TYPE

The value of msapTlsPlcyIgmpSnpgImportPlcy specifies the policy statement that is be applied to all incoming IGMP messages on the MSAP.

OBJECT-TYPE

The value of msapTlsPlcyIgmpSnpgFastLeave specifies whether fast leave is allowed on this MSAP. If set to 'enabled', the system prunes the port on which an IGMP 'leave' message has been received without waiting for the Group Specific Query to timeout.

OBJECT-TYPE

The value of msapTlsPlcyIgmpSnpgSendQueries specifies whether the system generates General Queries by itself on the MSAP.

OBJECT-TYPE

The value of msapTlsPlcyIgmpSnpgGenQueryIntv specifies the interval (in seconds) between two consecutive general queries sent by the system on the MSAP. The value of this object is only meaningful when the value of msapTlsPlcyIgmpSnpgSendQueries is 'enabled'.

OBJECT-TYPE

The value of msapTlsPlcyIgmpSnpgQueryRespIntv specifies the maximum response time (in seconds) advertised in IGMPv2/v3 queries. The value of this object is only meaningful when the value of msapTlsPlcyIgmpSnpgSendQueries is 'enabled'.

OBJECT-TYPE

The value of msapTlsPlcyIgmpSnpgRobustCount specifies the robustness variable on the MSAP. This object allows tuning for the expected packet loss on the MSAP. If a MSAP is expected to be lossy, the Robustness Variable may be increased. IGMP snooping is robust to (Robustness Variable-1) packet losses. The value of this object is only meaningful when the value of msapTlsPlcyIgmpSnpgSendQueries is 'enabled'.

OBJECT-TYPE

The value of msapTlsPlcyIgmpSnpgLastMembIntvl specifies the Max Response Time (in tenths of a second) used in Group-Specific and Group-Source-Specific Queries sent in response to 'leave' messages. This is also the amount of time between Group-Specific Query messages. This value may be tuned to modify the leave latency of the network. A reduced value results in reduced time to detect the loss of the last member of a group.

OBJECT-TYPE

The value of msapTlsPlcyIgmpSnpgMaxNbrGrps specifies how many group addresses are allowed for the MSAP. The value 0 means that no limit is imposed.

OBJECT-TYPE

The value of msapTlsPlcyIgmpSnpgMvrFromVplsId specifies from which VPLS the multicast streams corresponding to the groups learned via the MSAP are copied. Groups which cannot be joined to the corresponding MVR VPLS (because MVR is not up or the configured MVR policy rejects the group) copy the multicast streams from the local VPLS if IGMP snooping is up (i.e. tlsIgmpSnpgCfgAdminState is 'enabled').

OBJECT-TYPE

The value of msapTlsPlcyIgmpSnpgVersion specifies the version of IGMP running on the MSAP.

OBJECT-TYPE

The value of msapTlsPlcyIgmpSnpgMcacPlcyName specifies the name of the multicast CAC (Connection Admission Control) policy.

OBJECT-TYPE

The value of msapTlsPlcyIgmpSnpgMcacUncnstBW specifies the bandwidth assigned for interface's multicast CAC policy traffic in kilo-bits per second(kbps). If the default value of '-1' is set, there is no constraint on bandwidth allocated at the interface. If the value of msapTlsPlcyIgmpSnpgMcacUncnstBW is set to '0' and if a multicast CAC policy is assigned on the interface, then no group (channel) from that policy is allowed on that interface.

OBJECT-TYPE

The value of msapTlsPlcyIgmpSnpgMcacPrRsvMnBW specifies the bandwidth pre-reserved for all the mandatory channels on a given interface in kilo-bits per second(kbps). If the value of msapTlsPlcyIgmpSnpgMcacUncnstBW is '0', no mandatory channels are allowed. If the value of msapTlsPlcyIgmpSnpgMcacPrRsvMnBW is '-1', then all mandatory and optional channels are allowed. If the value of msapTlsPlcyIgmpSnpgMcacPrRsvMnBW is equal to the value of msapTlsPlcyIgmpSnpgMcacUncnstBW, then all the unconstrained bandwidth on a given interface is allocated to mandatory channels configured through multicast CAC policy on that interface and no optional groups (channels) are allowed. The value of msapTlsPlcyIgmpSnpgMcacPrRsvMnBW should always be less than or equal to that of msapTlsPlcyIgmpSnpgMcacUncnstBW. An attempt to set the value of msapTlsPlcyIgmpSnpgMcacPrRsvMnBW greater than that of msapTlsPlcyIgmpSnpgMcacUncnstBW will result in 'inconsistentValue' error.

OBJECT-TYPE

The msapIgmpSnpgMcacLevelTable has an entry for each multicast CAC policy constraint level configured for a Managed SAP policy.

OBJECT-TYPE

Each row entry represents a multicast CAC policy bundle level constraints for a particular Managed SAP policy. Entries are created and deleted by the user.

OBJECT-TYPE

The value of msapIgmpSnpgMcacLevelId indicates the level id of the multicast CAC policy bundle constraint. The value of level 1 has the highest priority and level 8 the lowest.

OBJECT-TYPE

The value of msapIgmpSnpgMcacLevelRowStatus is used for creation and deletion of level constraint in a CAC for a Managed SAP policy.

OBJECT-TYPE

The value of msapIgmpSnpgMcacLevelLastChanged indicates the sysUpTime at the time of the last modification of this entry. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The value of msapIgmpSnpgMcacLevelBW specifies the bandwidth in kilo-bits per second (kbps) for the level.

OBJECT-TYPE

The msapIgmpSnpgMcacLagTable has an entry for each lag port configured for a multicast CAC policy bundle configured for a Managed SAP policy.

OBJECT-TYPE

Each row entry represents a particular multicast CAC lag port constraints for a Managed SAP policy.. Entries are created and deleted by the user.

OBJECT-TYPE

The value of msapIgmpSnpgMcacLagPortsDown indicates the configured number of ports in a lag group that are down. If the number of ports available in the lag is reduced by the number of ports configured for msapIgmpSnpgMcacLagPortsDown object then bandwidth allowed for bundle will be updated to the value of msapIgmpSnpgMcacLevelBW indexed by msapIgmpSnpgMcacLagLevel value.

OBJECT-TYPE

The value of msapIgmpSnpgMcacLagRowStatus is used for creation and deletion of lag constraint in a CAC policy.

OBJECT-TYPE

The value of msapIgmpSnpgMcacLagLastChanged indicates the sysUpTime at the time of the last modification of this entry. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The value of msapIgmpSnpgMcacLagLevel specifies the level id to use when the value of msapIgmpSnpgMcacLagPortsDown matches the actual number of ports down in a lag. Using the value of msapIgmpSnpgMcacLagLevel as an index, the operational MSAP unconstrained bandwidth will be set to msapIgmpSnpgMcacLevelBW. By default, for all lag constraints the link level will be set to 1 at row creation.

OBJECT-TYPE

A table that contains Managed SAP information.

OBJECT-TYPE

Information about a specific Managed SAP.

OBJECT-TYPE

The value of msapInfoCreationSapPortEncapVal indicates the port encapsulation value of the SAP with a sapSubType value of 'capture' that created this MSAP.

OBJECT-TYPE

The value of msapInfoCreationPlcyName indicates the value of the msapPlcyName object for MSAP policy used to create this MSAP.

OBJECT-TYPE

The value of msapInfoReEvalPolicy specifies whether to re-apply the Managed SAP policy associated with this MSAP. When a SET of this object is done with a value of 'doAction', the system will attempt to re-apply the MSAP policy indicated by msapInfoCreationPlcyName. If this action is successful, 'noError' will be returned. If this action is unsuccessful, an 'inconsistentValue' error will be returned. Attempting to SET this object with a value of 'notApplicable' will have no effect and will return 'noError'. SNMP GET and GETNEXT requests on this object will return 'notApplicable'.

OBJECT-TYPE

The value of msapInfoLastChanged indicates the sysUpTime at the time of the last modification of this entry. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

A table that contains statistics for SAPs with a sapSubType value of 'capture'.

OBJECT-TYPE

Statistics for a specific 'capture' SAP.

OBJECT-TYPE

The value of msapCaptureSapStatsTriggerType indicates the type of trigger packets this entry is for.

OBJECT-TYPE

The value of msapCaptureSapStatsPktsRecvd indicates the number of packets received on this 'capture' SAP.

OBJECT-TYPE

The value of msapCaptureSapStatsPktsRedirect indicates the number of packets redirected on this 'capture' SAP.

OBJECT-TYPE

The value of msapCaptureSapStatsPktsDropped indicates the number of packets dropped on this 'capture' SAP.

OBJECT-TYPE

The sapTlsMrpTable augments sapTlsInfoTable with attributes of the Multiple Registration Protocol (MRP) feature for the TLS SAP.

OBJECT-TYPE

MRP specific information about a SAP in a TLS.

OBJECT-TYPE

The value of sapTlsMrpRxPdus indicates the number of MRP packets received on this SAP.

OBJECT-TYPE

The value of sapTlsMrpDroppedPdus indicates the number of dropped MRP packets on this SAP.

OBJECT-TYPE

The value of sapTlsMrpTxPdus indicates the number of MRP packets transmitted on this SAP.

OBJECT-TYPE

The value of sapTlsMrpRxNewEvent indicates the number of 'New' MRP events received on this SAP.

OBJECT-TYPE

The value of sapTlsMrpRxJoinInEvent indicates the number of 'Join-In' MRP events received on this SAP.

OBJECT-TYPE

The value of sapTlsMrpRxInEvent indicates the number of 'In' MRP events received on this SAP.

OBJECT-TYPE

The value of sapTlsMrpRxJoinEmptyEvent indicates the number of 'Join Empty' MRP events received on this SAP.

OBJECT-TYPE

The value of sapTlsMrpRxEmptyEvent indicates the number of 'Empty' MRP events received on this SAP.

OBJECT-TYPE

The value of sapTlsMrpRxLeaveEvent indicates the number of 'Leave' MRP events received on this SAP.

OBJECT-TYPE

The value of sapTlsMrpTxNewEvent indicates the number of 'New' MRP events transmitted on this SAP.

OBJECT-TYPE

The value of sapTlsMrpTxJoinInEvent indicates the number of 'Join-In' MRP events transmitted on this SAP.

OBJECT-TYPE

The value of sapTlsMrpTxInEvent indicates the number of 'In' MRP events transmitted on this SAP.

OBJECT-TYPE

The value of sapTlsMrpTxJoinEmptyEvent indicates the number of 'Join Empty' MRP events transmitted on this SAP.

OBJECT-TYPE

The value of sapTlsMrpTxEmptyEvent indicates the number of 'Empty' MRP events transmitted on this SAP.

OBJECT-TYPE

The value of sapTlsMrpTxLeaveEvent indicates the number of 'Leave' MRP events transmitted on this SAP.

OBJECT-TYPE

This table contains an entry for each MAC address managed by Multiple MAC Registration Protocol (MMRP) on the SAP for the TLS. Entries are dynamically created and destroyed by the system as the MAC Addresses are registered or declared in MMRP.

OBJECT-TYPE

MMRP specific information about a MAC address managed by MMRP on a SAP in a TLS.

OBJECT-TYPE

The value of sapTlsMmrpMacAddr indicates an ethernet MAC address which is being managed by MMRP on this SAP.

OBJECT-TYPE

The value of sapTlsMmrpDeclared indicates whether the MRP applicant on this SAP is declaring this MAC address on behalf of MMRP.

OBJECT-TYPE

The value of sapTlsMmrpRegistered indicates whether the MRP registrant on this SAP has notified MMRP of a registration of this MAC address.

OBJECT-TYPE

The value of msapPlcyTblLastChgd indicates the sysUpTime at the time of the last modification of msapPlcyTable. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The value of msapTlsPlcyTblLastChgd indicates the sysUpTime at the time of the last modification of msapTlsPlcyTable. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The value of msapIgmpSnpgMcacLvlTblLastChgd indicates the sysUpTime at the time of the last modification of msapIgmpSnpgMcacLevelTable. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The value of msapIgmpSnpgMcacLagTblLastChgd indicates the sysUpTime at the time of the last modification of msapIgmpSnpgMcacLagTable. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

The value of msapInfoTblLastChgd indicates the sysUpTime at the time of the last modification of msapInfoTable. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-IDENTITY

OBJECT-TYPE

The ID of the access port where a SAP is defined. This object is used by the sapPortStateChangeProcessed notification to indicate the port ID that changed state and that resulted in having the associated sapStatusChanged events suppressed for all SAPs on that port.

OBJECT-TYPE

The status of the Managed SAP which is used by the msapStateChanged notification to indicate what state the Managed SAP has entered: 'created', 'modified', or 'deleted'.

OBJECT-TYPE

The value of the object svcManagedSapCreationError indicates the reason why the system was unable to create the managed SAP.

OBJECT-IDENTITY

OBJECT-IDENTITY