MIBs Depot

ZhoneVdsl-MIB

Registered at
1.3.6.1.4.1.5504.5.13.1
1.3.6.1.4.1.5504.6.110
Last updated
2013-02-27 16:00
Organization
ADSLMIB Working Group
Revisions
2013-10-08 06:43, 2013-02-27 18:00, 2013-02-11 14:15, 2011-12-01 05:59, 2011-11-16 12:14, 2011-10-18 11:13, 2011-10-14 11:24, 2011-04-28 11:55, 2010-11-05 07:16, 2010-10-13 04:59, 2010-06-07 11:29, 2010-05-31 00:11, 2010-04-02 06:40, 2010-03-29 05:54, 2010-03-02 08:44, 2008-04-14 12:28, 2008-02-05 08:56, 2007-10-23 16:53, 2007-10-05 13:24, 2007-06-20 10:56, 2007-03-14 16:08, 2006-12-05 15:09, 2006-11-10 08:58, 2006-10-10 15:25, 2006-09-10 11:16, 2006-08-22 17:21, 2006-06-15 15:29, 2004-02-19 00:00
Namespace
zhone
Source file
ZhoneVdsl-MIB
Digest
sha256:d1dac04be1c24fa3575085e8c05b0435503c106137fd9ee56da8241ffaba215f

Description

The MIB module defining objects for the management of a pair of VDSL transceivers at each end of the VDSL line. Each such line has an entry in an ifTable which may include multiple transceiver lines. An agent may reside at either end of the VDSL line. However, the MIB is designed to require no management communication between them beyond that inherent in the low-level VDSL line protocol. The agent may monitor and control this protocol for its needs. VDSL lines may support optional Fast or Interleaved channels. If these are supported, additional entries corresponding to the supported channels must be created in the ifTable. Thus a VDSL line that supports both channels will have three entries in the ifTable, one for each physical, fast, and interleaved, whose ifType values are equal to vdsl(97), fast(125), and interleaved(124), respectively. The ifStackTable is used to represent the relationship between the entries. Naming Conventions: Vtuc -- (VTUC) transceiver at near (Central) end of line Vtur -- (VTUR) transceiver at Remote end of line Vtu -- One of either Vtuc or Vtur Curr -- Current Prev -- Previous Atn -- Attenuation ES -- Errored Second. SES -- Severely Errored Second UAS -- Unavailable Second LCS -- Line Code Specific Lof -- Loss of Frame Lol -- Loss of Link Los -- Loss of Signal Lpr -- Loss of Power xxxs -- Sum of Seconds in which xxx has occured (e.g., xxx = Lof, Los, Lpr, Lol) Max -- Maximum Mgn -- Margin Min -- Minimum Psd -- Power Spectral Density Snr -- Signal to Noise Ratio Tx -- Transmit Blks -- Blocks Copyright (C) The Internet Society (2004). This version of this MIB module is part of RFC 3728: see the RFC itself for full legal notices.

Contact

WG-email: adslmib@ietf.org Info: https://www1.ietf.org/mailman/listinfo/adslmib Chair: Mike Sneed Sand Channel Systems Postal: P.O. Box 37324 Raleigh, NC 27627-7324 USA Email: sneedmike@hotmail.com Phone: +1 206 600 7022 Co-editor: Bob Ray PESA Switching Systems, Inc. Postal: 330-A Wynn Drive Huntsville, AL 35805 USA Email: rray@pesa.com Phone: +1 256 726 9200 ext. 142 Co-editor: Rajesh Abbi Alcatel USA Postal: 2301 Sugar Bush Road Raleigh, NC 27612-3339 USA Email: Rajesh.Abbi@alcatel.com Phone: +1 919 850 6194

Imports

FromSymbols
HC-PerfHist-TC-MIBHCPerfCurrentCount, HCPerfIntervalCount, HCPerfTimeElapsed
IF-MIBifIndex
SNMP-FRAMEWORK-MIBSnmpAdminString
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP
SNMPv2-SMIGauge32, Integer32, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, Unsigned32, iso, transmission
SNMPv2-TCDisplayString, RowStatus, TEXTUAL-CONVENTION, TruthValue
ZhonezhoneModules, zhoneVdsl

Imported by

Nothing in this corpus imports this module.

Load order

Every file a consumer needs in order to load this module, dependencies first.

HC-PerfHist-TC-MIB
IANAifType-MIB
IF-MIB
SNMP-FRAMEWORK-MIB
SNMPv2-CONF
SNMPv2-MIB
SNMPv2-SMI
SNMPv2-TC
Zhone
ZhoneVdsl-MIB

Textual conventions

NameOIDSyntaxAccessStatus
ZhoneVdslLineCodingType
TEXTUAL-CONVENTION
This data type is used as the syntax for the VDSL Line Code. Attributes with this syntax identify the line coding used. Specified as an INTEGER, the three values are: other(1) -- none of the following mcm(2) -- Multiple Carrier Modulation scm(3) -- Single Carrier Modulation
current
ZhoneVdslLineEntity
TEXTUAL-CONVENTION
Identifies a transceiver as being either Vtuc or Vtur. A VDSL line consists of two transceivers, a Vtuc and a Vtur. Attributes with this syntax reference the two sides of a line. Specified as an INTEGER, the two values are: vtuc(1) -- central site transceiver vtur(2) -- remote site transceiver
current

Objects

NameOIDSyntaxAccessStatus
zhoneVdslLineMib
OBJECT-IDENTITY
1.3.6.1.4.1.5504.5.13.1
zhoneVdslNotifications
OBJECT-IDENTITY
1.3.6.1.4.1.5504.5.13.1.0
zhoneVdslMibObjects
OBJECT-IDENTITY
1.3.6.1.4.1.5504.5.13.1.1
zhoneVdslLineTable
OBJECT-TYPE
This table includes common attributes describing both ends of the line. It is required for all VDSL physical interfaces. VDSL physical interfaces are those ifEntries where ifType is equal to vdsl(97).
1.3.6.1.4.1.5504.5.13.1.1.1not-accessiblecurrent
zhoneVdslLineEntry
OBJECT-TYPE
An entry in the vdslLineTable.
1.3.6.1.4.1.5504.5.13.1.1.1.1not-accessiblecurrent
zhoneVdslLineCoding
OBJECT-TYPE
Specifies the VDSL coding type used on this line.
1.3.6.1.4.1.5504.5.13.1.1.1.1.1ZhoneVdslLineCodingTyperead-onlycurrent
zhoneVdslLineType
OBJECT-TYPE
Defines the type of VDSL physical line entity that exists, by defining whether and how the line is channelized. If the line is channelized, the value will be other than noChannel(1). This object defines which channel type(s) are supported. Defined values are: noChannel(1) -- no channels exist fastOnly(2) -- only fast channel exists interleavedOnly(3) -- only interleaved channel exists fastOrInterleaved(4) -- either fast or interleaved channel -- exist, but only one at a time fastAndInterleaved(5) -- both fast and interleaved channels -- exist Note that 'slow' and 'interleaved' refer to the same channel. In the case that the line is channelized, the manager can use the ifStackTable to determine the ifIndex for the associated channel(s).
1.3.6.1.4.1.5504.5.13.1.1.1.1.2INTEGER {noChannel(1), fastOnly(2), interleavedOnly(3), fastOrInterleaved(4), fastAndInterleaved(5)}read-onlycurrent
zhoneVdslLineConfProfile
OBJECT-TYPE
The value of this object identifies the row in the VDSL Line Configuration Profile Table, zhoneVdslLineConfProfileTable, which applies for this VDSL line, and channels if applicable. This object MUST be maintained in a persistent manner.
1.3.6.1.4.1.5504.5.13.1.1.1.1.3SnmpAdminString (SIZE(1..32))read-writecurrent
zhoneVdslLineAlarmConfProfile
OBJECT-TYPE
The value of this object identifies the row in the VDSL Line Alarm Configuration Profile Table, zhoneVdslLineAlarmConfProfileTable, which applies to this VDSL line, and channels if applicable. This object MUST be maintained in a persistent manner.
1.3.6.1.4.1.5504.5.13.1.1.1.1.4SnmpAdminString (SIZE(1..32))read-writecurrent
zhoneVdslPhysTable
OBJECT-TYPE
This table provides one row for each Vtu. Each row contains the Physical Layer Parameters table for that Vtu. VDSL physical interfaces are those ifEntries where ifType is equal to vdsl(97).
1.3.6.1.4.1.5504.5.13.1.1.2not-accessiblecurrent
zhoneVdslPhysEntry
OBJECT-TYPE
An entry in the vdslPhysTable.
1.3.6.1.4.1.5504.5.13.1.1.2.1not-accessiblecurrent
zhoneVdslPhysSide
OBJECT-TYPE
Identifies whether the transceiver is the Vtuc or Vtur.
1.3.6.1.4.1.5504.5.13.1.1.2.1.1ZhoneVdslLineEntitynot-accessiblecurrent
zhoneVdslPhysInvSerialNumber
OBJECT-TYPE
The vendor specific string that identifies the vendor equipment.
1.3.6.1.4.1.5504.5.13.1.1.2.1.2OCTET STRING (SIZE(0..32))read-onlycurrent
zhoneVdslPhysInvVendorID
OBJECT-TYPE
The vendor ID code is a copy of the binary vendor identification field expressed as readable characters in hexadecimal notation.
1.3.6.1.4.1.5504.5.13.1.1.2.1.3OCTET STRING (SIZE(0..16))read-onlycurrent
zhoneVdslPhysInvVersionNumber
OBJECT-TYPE
The vendor specific version number sent by this Vtu as part of the initialization messages. It is a copy of the binary version number field expressed as readable characters in hexadecimal notation.
1.3.6.1.4.1.5504.5.13.1.1.2.1.4OCTET STRING (SIZE(0..16))read-onlycurrent
zhoneVdslPhysCurrSnrMgn
OBJECT-TYPE
Noise Margin as seen by this Vtu with respect to its received signal in 0.10dB. The effective range is -31.75 to +31.75 dB.
1.3.6.1.4.1.5504.5.13.1.1.2.1.5Integer32 (-127..127)read-onlycurrent
zhoneVdslPhysCurrAtn
OBJECT-TYPE
Measured difference in the total power transmitted by the peer Vtu and the total power received by this Vtu. The effective range is 0 to +63.75 dB.
1.3.6.1.4.1.5504.5.13.1.1.2.1.6Gauge32 (0..255)read-onlycurrent
zhoneVdslPhysCurrStatus
OBJECT-TYPE
Indicates current state of the Vtu line. This is a bit-map of possible conditions. The various bit positions are: 0 noDefect There are no defects on the line. 1 lossOfFraming Vtu failure due to not receiving a valid frame. 2 lossOfSignal Vtu failure due to not receiving signal. 3 lossOfPower Vtu failure due to loss of power. 4 lossOfSignalQuality Loss of Signal Quality is declared when the Noise Margin falls below the Minimum Noise Margin, or the bit-error-rate exceeds 10^-7. 5 lossOfLink Vtu failure due to inability to link with peer Vtu. Set whenever the transceiver is in the 'Warm Start' state. 6 dataInitFailure Vtu failure during initialization due to bit errors corrupting startup exchange data. 7 configInitFailure Vtu failure during initialization due to peer Vtu not able to support requested configuration. 8 protocolInitFailure Vtu failure during initialization due to incompatible protocol used by the peer Vtu. 9 noPeerVtuPresent Vtu failure during initialization due to no activation sequence detected from peer Vtu. This is intended to supplement ifOperStatus.
1.3.6.1.4.1.5504.5.13.1.1.2.1.7Bits {noDefect(0), lossOfFraming(1), lossOfSignal(2), lossOfPower(3), lossOfSignalQuality(4), lossOfLink(5), dataInitFailure(6), configInitFailure(7), protocolInitFailure(8), noPeerVtuPresent(9)}read-onlycurrent
zhoneVdslPhysCurrOutputPwr
OBJECT-TYPE
Measured total output power transmitted by this VTU. This is the measurement that was reported during the last activation sequence.
1.3.6.1.4.1.5504.5.13.1.1.2.1.8Integer32 (0..160)read-onlycurrent
zhoneVdslPhysCurrAttainableRate
OBJECT-TYPE
Indicates the maximum currently attainable data rate in steps of 1000 bits/second by the Vtu. This value will be equal to or greater than vdslPhysCurrLineRate. Note that for SCM, the minimum and maximum data rates are equal. Note: 1 kbps = 1000 bps.
1.3.6.1.4.1.5504.5.13.1.1.2.1.9Gauge32read-onlycurrent
zhoneVdslPhysCurrLineRate
OBJECT-TYPE
Indicates the current data rate in steps of 1000 bits/second by the Vtu. This value will be less than or equal to vdslPhysCurrAttainableRate. Note: 1 kbps = 1000 bps.
1.3.6.1.4.1.5504.5.13.1.1.2.1.10Gauge32read-onlycurrent
zhoneVdslPhysCurrConnType
OBJECT-TYPE
Indicates current connection type. unknown(1) - could not determine connection type not-connected(2) - connection has not been established invalid(3) - unknown connection established adsl(4) - G.992.1/2 adsl2(5) - G.992.3/4 adsl2-annexm(6) - G.992.3/4 with Annex M adsl2plus(7) - G.992.5 adsl2plus-annexm(8) - G.992.5 with Annex M vdsl1(9) - G.993.1 vdsl2(10) - G.993.2
1.3.6.1.4.1.5504.5.13.1.1.2.1.12INTEGER {unknown(1), not-connected(2), invalid(3), adsl(4), adsl2(5), adsl2-annexm(6), adsl2plus(7), adsl2plus-annexm(8), vdsl1(9), vdsl2(10)}read-onlycurrent
zhoneVdslPhysCurrProfile
OBJECT-TYPE
Indicates current VDSL profile being used in the connection. This object is only valid for VDSL connections.
1.3.6.1.4.1.5504.5.13.1.1.2.1.13INTEGER {g993-2-8a(1), g993-2-8b(2), g993-2-8c(3), g993-2-8d(4), g993-2-12a(5), g993-2-12b(6), g993-2-17a(7), g993-2-30a(8), no-vdsl-connection(9)}read-onlycurrent
zhoneVdslPhysPhyRActive
OBJECT-TYPE
Phy Retransmit Rx Queue Active.
1.3.6.1.4.1.5504.5.13.1.1.2.1.14TruthValueread-onlycurrent
zhoneVdslPhysGinpActive
OBJECT-TYPE
G.INP/ITU-G.998.4 feature active
1.3.6.1.4.1.5504.5.13.1.1.2.1.15TruthValueread-onlycurrent
zhoneVdslPhysTransportMode
OBJECT-TYPE
Transport mode, either ATM or PTM
1.3.6.1.4.1.5504.5.13.1.1.2.1.16INTEGER {atm(1), ptm(2)}read-onlycurrent
zhoneVdslChanTable
OBJECT-TYPE
This table provides one row for each Vtu channel. VDSL channel interfaces are those ifEntries where ifType is equal to interleave(124) or fast(125).
1.3.6.1.4.1.5504.5.13.1.1.3not-accessiblecurrent
zhoneVdslChanEntry
OBJECT-TYPE
An entry in the vdslChanTable.
1.3.6.1.4.1.5504.5.13.1.1.3.1not-accessiblecurrent
zhoneVdslChanInterleaveDelay
OBJECT-TYPE
Interleave Delay for this channel. Interleave delay applies only to the interleave (slow) channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency. In the case where the ifType is fast(125), return a value of zero.
1.3.6.1.4.1.5504.5.13.1.1.3.1.1Gauge32read-onlycurrent
zhoneVdslChanCrcBlockLength
OBJECT-TYPE
Indicates the length of the channel data-block on which the CRC operates.
1.3.6.1.4.1.5504.5.13.1.1.3.1.2Gauge32read-onlycurrent
zhoneVdslChanCurrTxRate
OBJECT-TYPE
Actual transmit data rate on this channel. Note: 1 kbps = 1000 bps.
1.3.6.1.4.1.5504.5.13.1.1.3.1.3Gauge32read-onlycurrent
zhoneVdslChanCurrTxSlowBurstProtect
OBJECT-TYPE
Actual level of impulse noise (burst) protection for an interleaved (slow) channel. This parameter is not applicable to fast channels. For fast channels, a value of zero shall be returned.
1.3.6.1.4.1.5504.5.13.1.1.3.1.4Gauge32 (0..1275)read-onlycurrent
zhoneVdslChanCurrTxFastFec
OBJECT-TYPE
Actual Forward Error Correction (FEC) redundancy related overhead for a fast channel. This parameter is not applicable to an interleaved (slow) channel. For interleaved channels, a value of zero shall be returned.
1.3.6.1.4.1.5504.5.13.1.1.3.1.5Gauge32 (0..50)read-onlycurrent
zhoneVdslPerfDataTable
OBJECT-TYPE
This table provides one row for each VDSL physical interface. VDSL physical interfaces are those ifEntries where ifType is equal to vdsl(97).
1.3.6.1.4.1.5504.5.13.1.1.4not-accessiblecurrent
zhoneVdslPerfDataEntry
OBJECT-TYPE
An entry in the vdslPerfDataTable.
1.3.6.1.4.1.5504.5.13.1.1.4.1not-accessiblecurrent
zhoneVdslPerfDataValidIntervals
OBJECT-TYPE
Valid Intervals per definition found in HC-PerfHist-TC-MIB.
1.3.6.1.4.1.5504.5.13.1.1.4.1.1Integer32 (0..96)read-onlycurrent
zhoneVdslPerfDataInvalidIntervals
OBJECT-TYPE
Invalid Intervals per definition found in HC-PerfHist-TC-MIB.
1.3.6.1.4.1.5504.5.13.1.1.4.1.2Integer32 (0..96)read-onlycurrent
zhoneVdslPerfDataLofs
OBJECT-TYPE
Count of seconds since the unit was last reset that there was Loss of Framing.
1.3.6.1.4.1.5504.5.13.1.1.4.1.3Unsigned32read-onlycurrent
zhoneVdslPerfDataLoss
OBJECT-TYPE
Count of seconds since the unit was last reset that there was Loss of Signal.
1.3.6.1.4.1.5504.5.13.1.1.4.1.4Unsigned32read-onlycurrent
zhoneVdslPerfDataLprs
OBJECT-TYPE
Count of seconds since the unit was last reset that there was Loss of Power.
1.3.6.1.4.1.5504.5.13.1.1.4.1.5Unsigned32read-onlycurrent
zhoneVdslPerfDataLols
OBJECT-TYPE
Count of seconds since the unit was last reset that there was Loss of Link.
1.3.6.1.4.1.5504.5.13.1.1.4.1.6Unsigned32read-onlycurrent
zhoneVdslPerfDataESs
OBJECT-TYPE
Count of Errored Seconds since the unit was last reset. An Errored Second is a one-second interval containing one or more CRC anomalies, or one or more LOS or LOF defects.
1.3.6.1.4.1.5504.5.13.1.1.4.1.7Unsigned32read-onlycurrent
zhoneVdslPerfDataSESs
OBJECT-TYPE
Count of Severely Errored Seconds since the unit was last reset.
1.3.6.1.4.1.5504.5.13.1.1.4.1.8Unsigned32read-onlycurrent
zhoneVdslPerfDataUASs
OBJECT-TYPE
Count of Unavailable Seconds since the unit was last reset.
1.3.6.1.4.1.5504.5.13.1.1.4.1.9Unsigned32read-onlycurrent
zhoneVdslPerfDataInits
OBJECT-TYPE
Count of the line initialization attempts since the unit was last reset. This count includes both successful and failed attempts.
1.3.6.1.4.1.5504.5.13.1.1.4.1.10Unsigned32read-onlycurrent
zhoneVdslPerfDataCurr15MinTimeElapsed
OBJECT-TYPE
Total elapsed seconds in this interval.
1.3.6.1.4.1.5504.5.13.1.1.4.1.11Integer32 (0..86399)read-onlycurrent
zhoneVdslPerfDataCurr15MinLofs
OBJECT-TYPE
Count of seconds during this interval that there was Loss of Framing.
1.3.6.1.4.1.5504.5.13.1.1.4.1.12Unsigned32read-onlycurrent
zhoneVdslPerfDataCurr15MinLoss
OBJECT-TYPE
Count of seconds during this interval that there was Loss of Signal.
1.3.6.1.4.1.5504.5.13.1.1.4.1.13Unsigned32read-onlycurrent
zhoneVdslPerfDataCurr15MinLprs
OBJECT-TYPE
Count of seconds during this interval that there was Loss of Power.
1.3.6.1.4.1.5504.5.13.1.1.4.1.14Unsigned32read-onlycurrent
zhoneVdslPerfDataCurr15MinLols
OBJECT-TYPE
Count of seconds during this interval that there was Loss of Link.
1.3.6.1.4.1.5504.5.13.1.1.4.1.15Unsigned32read-onlycurrent
zhoneVdslPerfDataCurr15MinESs
OBJECT-TYPE
Count of Errored Seconds during this interval. An Errored Second is a one-second interval containing one or more CRC anomalies, or one or more LOS or LOF defects.
1.3.6.1.4.1.5504.5.13.1.1.4.1.16Unsigned32read-onlycurrent
zhoneVdslPerfDataCurr15MinSESs
OBJECT-TYPE
Count of Severely Errored Seconds during this interval.
1.3.6.1.4.1.5504.5.13.1.1.4.1.17Unsigned32read-onlycurrent
zhoneVdslPerfDataCurr15MinUASs
OBJECT-TYPE
Count of Unavailable Seconds during this interval.
1.3.6.1.4.1.5504.5.13.1.1.4.1.18Unsigned32read-onlycurrent
zhoneVdslPerfDataCurr15MinInits
OBJECT-TYPE
Count of the line initialization attempts during this interval. This count includes both successful and failed attempts.
1.3.6.1.4.1.5504.5.13.1.1.4.1.19Unsigned32read-onlycurrent
zhoneVdslPerfData1DayValidIntervals
OBJECT-TYPE
Valid Intervals per definition found in HC-PerfHist-TC-MIB.
1.3.6.1.4.1.5504.5.13.1.1.4.1.20Integer32 (0..96)read-onlycurrent
zhoneVdslPerfData1DayInvalidIntervals
OBJECT-TYPE
Invalid Intervals per definition found in HC-PerfHist-TC-MIB.
1.3.6.1.4.1.5504.5.13.1.1.4.1.21Integer32 (0..96)read-onlycurrent
zhoneVdslPerfDataCurr1DayTimeElapsed
OBJECT-TYPE
Number of seconds that have elapsed since the beginning of the current 1-day interval.
1.3.6.1.4.1.5504.5.13.1.1.4.1.22Integer32 (0..86399)read-onlycurrent
zhoneVdslPerfDataCurr1DayLofs
OBJECT-TYPE
Count of Loss of Framing (LOF) Seconds since the beginning of the current 1-day interval.
1.3.6.1.4.1.5504.5.13.1.1.4.1.23Unsigned32read-onlycurrent
zhoneVdslPerfDataCurr1DayLoss
OBJECT-TYPE
Count of Loss of Signal (LOS) Seconds since the beginning of the current 1-day interval.
1.3.6.1.4.1.5504.5.13.1.1.4.1.24Unsigned32read-onlycurrent
zhoneVdslPerfDataCurr1DayLprs
OBJECT-TYPE
Count of Loss of Power (LPR) Seconds since the beginning of the current 1-day interval.
1.3.6.1.4.1.5504.5.13.1.1.4.1.25Unsigned32read-onlycurrent
zhoneVdslPerfDataCurr1DayLols
OBJECT-TYPE
Count of Loss of Link (LOL) Seconds since the beginning of the current 1-day interval.
1.3.6.1.4.1.5504.5.13.1.1.4.1.26Unsigned32read-onlycurrent
zhoneVdslPerfDataCurr1DayESs
OBJECT-TYPE
Count of Errored Seconds (ES) since the beginning of the current 1-day interval.
1.3.6.1.4.1.5504.5.13.1.1.4.1.27Unsigned32read-onlycurrent
zhoneVdslPerfDataCurr1DaySESs
OBJECT-TYPE
Count of Severely Errored Seconds (SES) since the beginning of the current 1-day interval.
1.3.6.1.4.1.5504.5.13.1.1.4.1.28Unsigned32read-onlycurrent
zhoneVdslPerfDataCurr1DayUASs
OBJECT-TYPE
Count of Unavailable Seconds (UAS) since the beginning of the current 1-day interval.
1.3.6.1.4.1.5504.5.13.1.1.4.1.29Unsigned32read-onlycurrent
zhoneVdslPerfDataCurr1DayInits
OBJECT-TYPE
Count of the line initialization attempts since the beginning of the current 1-day interval. This count includes both successful and failed attempts.
1.3.6.1.4.1.5504.5.13.1.1.4.1.30Unsigned32read-onlycurrent
zhoneVdslPhyrRetransmittedCodewords
OBJECT-TYPE
Retransmitted Codewords
1.3.6.1.4.1.5504.5.13.1.1.4.1.31Unsigned32read-onlycurrent
zhoneVdslPhyrCorrectedRetransmittedCodewords
OBJECT-TYPE
Retransmitted corrected Codewords
1.3.6.1.4.1.5504.5.13.1.1.4.1.32Unsigned32read-onlycurrent
zhoneVdslPhyrUncorrectableRetransmittedCodewords
OBJECT-TYPE
Retransmitted uncorrectable Codewords
1.3.6.1.4.1.5504.5.13.1.1.4.1.33Unsigned32read-onlycurrent
zhoneVdslPhyrCurr15MinRetransmittedCodewords
OBJECT-TYPE
Current 15 minutes Retransmitted Codewords
1.3.6.1.4.1.5504.5.13.1.1.4.1.34Unsigned32read-onlycurrent
zhoneVdslPhyrCurr15MinCorrectedRetransmittedCodewords
OBJECT-TYPE
Current 15 minutes Retransmitted Corrected Codewords
1.3.6.1.4.1.5504.5.13.1.1.4.1.35Unsigned32read-onlycurrent
zhoneVdslPhyrCurr15MinUncorrectableRetransmittedCodewords
OBJECT-TYPE
Current 15 minutes Retransmitted Uncorrectable Codewords
1.3.6.1.4.1.5504.5.13.1.1.4.1.36Unsigned32read-onlycurrent
zhoneVdslPhyrCurr1DayRetransmittedCodewords
OBJECT-TYPE
Current Day Retransmitted Codewords
1.3.6.1.4.1.5504.5.13.1.1.4.1.37Unsigned32read-onlycurrent
zhoneVdslPhyrCurr1DayCorrectedRetransmittedCodewords
OBJECT-TYPE
Current Day Retransmitted Corrected Codewords
1.3.6.1.4.1.5504.5.13.1.1.4.1.38Unsigned32read-onlycurrent
zhoneVdslPhyrCurr1DayUncorrectableRetransmittedCodewords
OBJECT-TYPE
Current Day Retransmitted Uncorrectable Codewords
1.3.6.1.4.1.5504.5.13.1.1.4.1.39Unsigned32read-onlycurrent
zhoneVdslPhyrPrev1DayRetransmittedCodewords
OBJECT-TYPE
Previous Day Retransmitted Codewords
1.3.6.1.4.1.5504.5.13.1.1.4.1.40Unsigned32read-onlycurrent
zhoneVdslPhyrPrev1DayCorrectedRetransmittedCodewords
OBJECT-TYPE
Previous Day Retransmitted Corrected Codewords
1.3.6.1.4.1.5504.5.13.1.1.4.1.41Unsigned32read-onlycurrent
zhoneVdslPhyrPrev1DayUncorrectableRetransmittedCodewords
OBJECT-TYPE
Previous Day Retransmitted Uncorrectable Codewords
1.3.6.1.4.1.5504.5.13.1.1.4.1.42Unsigned32read-onlycurrent
zhoneVdslGinpLeftrSecs
OBJECT-TYPE
LEFTRS - This counter counts the number of seconds that experienced a Low Error Free Throughput Rate (LEFTR), i,e., seconds during which the Error Free Throughput dropped below the configured threshold.
1.3.6.1.4.1.5504.5.13.1.1.4.1.43Unsigned32read-onlycurrent
zhoneVdslGinpErrorFreeBits
OBJECT-TYPE
errorFreeBits - This counter counts the number of bits that crossed the alpha1/beta1 interface (bits available to carry user payload).
1.3.6.1.4.1.5504.5.13.1.1.4.1.44Unsigned32read-onlycurrent
zhoneVdslGinpMinEftr
OBJECT-TYPE
minEFTR - This performance monitoring parameter records the lowest value of Error Free Throughput during the current interval.
1.3.6.1.4.1.5504.5.13.1.1.4.1.45Unsigned32read-onlycurrent
zhoneVdslGinpCurr15MinLeftrSecs
OBJECT-TYPE
LEFTRS - This counter counts the number of seconds that experienced a Low Error Free Throughput Rate (LEFTR), i,e., seconds during which the Error Free Throughput dropped below the configured threshold. This is the count for the current 15 minutes.
1.3.6.1.4.1.5504.5.13.1.1.4.1.46Unsigned32read-onlycurrent
zhoneVdslGinpCurr15MinErrorFreeBits
OBJECT-TYPE
errorFreeBits - This counter counts the number of bits that crossed the alpha1/beta1 interface (bits available to carry user payload). This is the count for the current 15 minutes.
1.3.6.1.4.1.5504.5.13.1.1.4.1.47Unsigned32read-onlycurrent
zhoneVdslGinpCurr15MinMinEftr
OBJECT-TYPE
minEFTR - This performance monitoring parameter records the lowest value of Error Free Throughput during the current interval. This is the count for the current 15 minutes.
1.3.6.1.4.1.5504.5.13.1.1.4.1.48Unsigned32read-onlycurrent
zhoneVdslGinpCurr1DayLeftrSecs
OBJECT-TYPE
LEFTRS - This counter counts the number of seconds that experienced a Low Error Free Throughput Rate (LEFTR), i,e., seconds during which the Error Free Throughput dropped below the configured threshold. This is the count for the current day.
1.3.6.1.4.1.5504.5.13.1.1.4.1.49Unsigned32read-onlycurrent
zhoneVdslGinpCurr1DayErrorFreeBits
OBJECT-TYPE
errorFreeBits - This counter counts the number of bits that crossed the alpha1/beta1 interface (bits available to carry user payload). This is the count for the current day.
1.3.6.1.4.1.5504.5.13.1.1.4.1.50Unsigned32read-onlycurrent
zhoneVdslGinpCurr1DayMinEftr
OBJECT-TYPE
minEFTR - This performance monitoring parameter records the lowest value of Error Free Throughput during the current interval. This is the count for the current day.
1.3.6.1.4.1.5504.5.13.1.1.4.1.51Unsigned32read-onlycurrent
zhoneVdslGinpPrev1DayLeftrSecs
OBJECT-TYPE
LEFTRS - This counter counts the number of seconds that experienced a Low Error Free Throughput Rate (LEFTR), i,e., seconds during which the Error Free Throughput dropped below the configured threshold. This is the count for the previous day.
1.3.6.1.4.1.5504.5.13.1.1.4.1.52Integer32read-onlycurrent
zhoneVdslGinpPrev1DayErrorFreeBits
OBJECT-TYPE
errorFreeBits - This counter counts the number of bits that crossed the alpha1/beta1 interface (bits available to carry user payload). This is the count for the previous day.
1.3.6.1.4.1.5504.5.13.1.1.4.1.53Integer32read-onlycurrent
zhoneVdslGinpPrev1DayMinEftr
OBJECT-TYPE
minEFTR - This performance monitoring parameter records the lowest value of Error Free Throughput during the current interval. This is the count for the previous day.
1.3.6.1.4.1.5504.5.13.1.1.4.1.54Integer32read-onlycurrent
zhoneVdslPerfIntervalTable
OBJECT-TYPE
This table provides one row for each Vtu performance data collection interval. VDSL physical interfaces are those ifEntries where ifType is equal to vdsl(97).
1.3.6.1.4.1.5504.5.13.1.1.5not-accessiblecurrent
zhoneVdslPerfIntervalEntry
OBJECT-TYPE
An entry in the vdslPerfIntervalTable.
1.3.6.1.4.1.5504.5.13.1.1.5.1not-accessiblecurrent
zhoneVdslPerfIntervalNumber
OBJECT-TYPE
Performance Data Interval number 1 is the most recent previous interval; interval 96 is 24 hours ago. Intervals 2 to 96 are optional.
1.3.6.1.4.1.5504.5.13.1.1.5.1.1Unsigned32 (1..96)not-accessiblecurrent
zhoneVdslPerfIntervalLofs
OBJECT-TYPE
Count of seconds in the interval when there was Loss of Framing.
1.3.6.1.4.1.5504.5.13.1.1.5.1.2HCPerfIntervalCountread-onlycurrent
zhoneVdslPerfIntervalLoss
OBJECT-TYPE
Count of seconds in the interval when there was Loss of Signal.
1.3.6.1.4.1.5504.5.13.1.1.5.1.3HCPerfIntervalCountread-onlycurrent
zhoneVdslPerfIntervalLprs
OBJECT-TYPE
Count of seconds in the interval when there was Loss of Power.
1.3.6.1.4.1.5504.5.13.1.1.5.1.4HCPerfIntervalCountread-onlycurrent
zhoneVdslPerfIntervalLols
OBJECT-TYPE
Count of seconds in the interval when there was Loss of Link.
1.3.6.1.4.1.5504.5.13.1.1.5.1.5HCPerfIntervalCountread-onlycurrent
zhoneVdslPerfIntervalESs
OBJECT-TYPE
Count of Errored Seconds (ES) in the interval. An Errored Second is a one-second interval containing one or more CRC anomalies, one or more LOS or LOF defects.
1.3.6.1.4.1.5504.5.13.1.1.5.1.6HCPerfIntervalCountread-onlycurrent
zhoneVdslPerfIntervalSESs
OBJECT-TYPE
Count of Severely Errored Seconds in the interval.
1.3.6.1.4.1.5504.5.13.1.1.5.1.7HCPerfIntervalCountread-onlycurrent
zhoneVdslPerfIntervalUASs
OBJECT-TYPE
Count of Unavailable Seconds in the interval.
1.3.6.1.4.1.5504.5.13.1.1.5.1.8HCPerfIntervalCountread-onlycurrent
zhoneVdslPerfIntervalInits
OBJECT-TYPE
Count of the line initialization attempts during this interval. This count includes both successful and failed attempts.
1.3.6.1.4.1.5504.5.13.1.1.5.1.9HCPerfIntervalCountread-onlycurrent
zhoneVdslPerf1DayIntervalTable
OBJECT-TYPE
This table provides one row for each VDSL performance data collection interval. This table contains live data from equipment. As such, it is NOT persistent.
1.3.6.1.4.1.5504.5.13.1.1.6not-accessiblecurrent
zhoneVdslPerf1DayIntervalEntry
OBJECT-TYPE
An entry in the vdslPerf1DayIntervalTable.
1.3.6.1.4.1.5504.5.13.1.1.6.1not-accessiblecurrent
zhoneVdslPerf1DayIntervalNumber
OBJECT-TYPE
History Data Interval number. Interval 1 is the most recent previous day; interval 30 is 30 days ago. Intervals 2 to 30 are optional.
1.3.6.1.4.1.5504.5.13.1.1.6.1.1Unsigned32 (1..30)not-accessiblecurrent
zhoneVdslPerf1DayIntervalMoniSecs
OBJECT-TYPE
The amount of time in the 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason.
1.3.6.1.4.1.5504.5.13.1.1.6.1.2HCPerfTimeElapsedread-onlycurrent
zhoneVdslPerf1DayIntervalLofs
OBJECT-TYPE
Count of Loss of Frame (LOF) Seconds during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs.
1.3.6.1.4.1.5504.5.13.1.1.6.1.3Unsigned32read-onlycurrent
zhoneVdslPerf1DayIntervalLoss
OBJECT-TYPE
Count of Loss of Signal (LOS) Seconds during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs.
1.3.6.1.4.1.5504.5.13.1.1.6.1.4Unsigned32read-onlycurrent
zhoneVdslPerf1DayIntervalLprs
OBJECT-TYPE
Count of Loss of Power (LPR) Seconds during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs.
1.3.6.1.4.1.5504.5.13.1.1.6.1.5Unsigned32read-onlycurrent
zhoneVdslPerf1DayIntervalLols
OBJECT-TYPE
Count of Loss of Link (LOL) Seconds during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs.
1.3.6.1.4.1.5504.5.13.1.1.6.1.6Unsigned32read-onlycurrent
zhoneVdslPerf1DayIntervalESs
OBJECT-TYPE
Count of Errored Seconds (ES) during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs.
1.3.6.1.4.1.5504.5.13.1.1.6.1.7Unsigned32read-onlycurrent
zhoneVdslPerf1DayIntervalSESs
OBJECT-TYPE
Count of Severely Errored Seconds (SES) during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs.
1.3.6.1.4.1.5504.5.13.1.1.6.1.8Unsigned32read-onlycurrent
zhoneVdslPerf1DayIntervalUASs
OBJECT-TYPE
Count of Unavailable Seconds (UAS) during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs.
1.3.6.1.4.1.5504.5.13.1.1.6.1.9Unsigned32read-onlycurrent
zhoneVdslPerf1DayIntervalInits
OBJECT-TYPE
Count of the line initialization attempts during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs. This count includes both successful and failed attempts.
1.3.6.1.4.1.5504.5.13.1.1.6.1.10Unsigned32read-onlycurrent
zhoneVdslChanPerfDataTable
OBJECT-TYPE
This table provides one row for each Vtu channel. VDSL channel interfaces are those ifEntries where ifType is equal to interleave(124) or fast(125).
1.3.6.1.4.1.5504.5.13.1.1.7not-accessiblecurrent
zhoneVdslChanPerfDataEntry
OBJECT-TYPE
An entry in the vdslChanPerfDataTable.
1.3.6.1.4.1.5504.5.13.1.1.7.1not-accessiblecurrent
zhoneVdslChanValidIntervals
OBJECT-TYPE
Valid Intervals per definition found in HC-PerfHist-TC-MIB.
1.3.6.1.4.1.5504.5.13.1.1.7.1.1Integer32 (0..96)read-onlycurrent
zhoneVdslChanInvalidIntervals
OBJECT-TYPE
Invalid Intervals per definition found in HC-PerfHist-TC-MIB.
1.3.6.1.4.1.5504.5.13.1.1.7.1.2Integer32 (0..96)read-onlycurrent
zhoneVdslChanFixedOctets
OBJECT-TYPE
Count of corrected octets since the unit was last reset.
1.3.6.1.4.1.5504.5.13.1.1.7.1.3Integer32read-onlycurrent
zhoneVdslChanBadBlks
OBJECT-TYPE
Count of uncorrectable blocks since the unit was last reset.
1.3.6.1.4.1.5504.5.13.1.1.7.1.4Integer32read-onlycurrent
zhoneVdslChanCurr15MinTimeElapsed
OBJECT-TYPE
Total elapsed seconds in this interval.
1.3.6.1.4.1.5504.5.13.1.1.7.1.5Integer32 (0..86399)read-onlycurrent
zhoneVdslChanCurr15MinFixedOctets
OBJECT-TYPE
Count of corrected octets in this interval.
1.3.6.1.4.1.5504.5.13.1.1.7.1.6Integer32read-onlycurrent
zhoneVdslChanCurr15MinBadBlks
OBJECT-TYPE
Count of uncorrectable blocks in this interval.
1.3.6.1.4.1.5504.5.13.1.1.7.1.7Integer32read-onlycurrent
zhoneVdslChan1DayValidIntervals
OBJECT-TYPE
Valid Intervals per definition found in HC-PerfHist-TC-MIB.
1.3.6.1.4.1.5504.5.13.1.1.7.1.8Integer32 (0..96)read-onlycurrent
zhoneVdslChan1DayInvalidIntervals
OBJECT-TYPE
Invalid Intervals per definition found in HC-PerfHist-TC-MIB.
1.3.6.1.4.1.5504.5.13.1.1.7.1.9Integer32 (0..96)read-onlycurrent
zhoneVdslChanCurr1DayTimeElapsed
OBJECT-TYPE
Number of seconds that have elapsed since the beginning of the current 1-day interval.
1.3.6.1.4.1.5504.5.13.1.1.7.1.10Integer32 (0..86399)read-onlycurrent
zhoneVdslChanCurr1DayFixedOctets
OBJECT-TYPE
Count of corrected octets since the beginning of the current 1-day interval.
1.3.6.1.4.1.5504.5.13.1.1.7.1.11Integer32read-onlycurrent
zhoneVdslChanCurr1DayBadBlks
OBJECT-TYPE
Count of uncorrectable blocks since the beginning of the current 1-day interval.
1.3.6.1.4.1.5504.5.13.1.1.7.1.12Integer32read-onlycurrent
zhoneVdslChanIntervalTable
OBJECT-TYPE
This table provides one row for each Vtu channel data collection interval. VDSL channel interfaces are those ifEntries where ifType is equal to interleave(124) or fast(125).
1.3.6.1.4.1.5504.5.13.1.1.8not-accessiblecurrent
zhoneVdslChanIntervalEntry
OBJECT-TYPE
An entry in the vdslChanIntervalTable.
1.3.6.1.4.1.5504.5.13.1.1.8.1not-accessiblecurrent
zhoneVdslChanIntervalNumber
OBJECT-TYPE
Performance Data Interval number 1 is the most recent previous interval; interval 96 is 24 hours ago. Intervals 2 to 96 are optional.
1.3.6.1.4.1.5504.5.13.1.1.8.1.1Unsigned32 (1..96)not-accessiblecurrent
zhoneVdslChanIntervalFixedOctets
OBJECT-TYPE
Count of corrected octets in this interval.
1.3.6.1.4.1.5504.5.13.1.1.8.1.2HCPerfIntervalCountread-onlycurrent
zhoneVdslChanIntervalBadBlks
OBJECT-TYPE
Count of uncorrectable blocks in this interval.
1.3.6.1.4.1.5504.5.13.1.1.8.1.3HCPerfIntervalCountread-onlycurrent
zhoneVdslChan1DayIntervalTable
OBJECT-TYPE
This table provides one row for each VDSL performance data collection interval. This table contains live data from equipment. As such, it is NOT persistent.
1.3.6.1.4.1.5504.5.13.1.1.9not-accessiblecurrent
zhoneVdslChan1DayIntervalEntry
OBJECT-TYPE
An entry in the vdslChan1DayIntervalTable.
1.3.6.1.4.1.5504.5.13.1.1.9.1not-accessiblecurrent
zhoneVdslChan1DayIntervalNumber
OBJECT-TYPE
History Data Interval number. Interval 1 is the most recent previous day; interval 30 is 30 days ago. Intervals 2 to 30 are optional.
1.3.6.1.4.1.5504.5.13.1.1.9.1.1Unsigned32 (1..30)not-accessiblecurrent
zhoneVdslChan1DayIntervalMoniSecs
OBJECT-TYPE
The amount of time in the 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason.
1.3.6.1.4.1.5504.5.13.1.1.9.1.2HCPerfTimeElapsedread-onlycurrent
zhoneVdslChan1DayIntervalFixedOctets
OBJECT-TYPE
Count of corrected octets in this interval.
1.3.6.1.4.1.5504.5.13.1.1.9.1.3HCPerfCurrentCountread-onlycurrent
zhoneVdslChan1DayIntervalBadBlks
OBJECT-TYPE
Count of uncorrectable blocks in this interval.
1.3.6.1.4.1.5504.5.13.1.1.9.1.4HCPerfCurrentCountread-onlycurrent
zhoneVdslLineConfProfileTable
OBJECT-TYPE
This table contains information on the VDSL line configuration. One entry in this table reflects a profile defined by a manager which can be used to configure the VDSL line. Entries in this table MUST be maintained in a persistent manner.
1.3.6.1.4.1.5504.5.13.1.1.11not-accessiblecurrent
zhoneVdslLineConfProfileEntry
OBJECT-TYPE
Each entry consists of a list of parameters that represents the configuration of a VDSL line. A default profile with an index of 'DEFVAL', will always exist and its parameters will be set to vendor specific values, unless otherwise specified in this document.
1.3.6.1.4.1.5504.5.13.1.1.11.1not-accessiblecurrent
zhoneVdslLineConfProfileName
OBJECT-TYPE
This object identifies a row in this table. A default profile with an index of 'DEFVAL', will always exist and its parameters will be set to vendor specific values, unless otherwise specified in this document.
1.3.6.1.4.1.5504.5.13.1.1.11.1.1SnmpAdminString (SIZE(1..32))not-accessiblecurrent
zhoneVdslLineConfDownRateMode
OBJECT-TYPE
Specifies the rate selection behavior for the line in the downstream direction. manual(1) forces the rate to the configured rate adaptAtInit(2) adapts the line at initialization only dynamic(3) adapts the line at initialization and showtime
1.3.6.1.4.1.5504.5.13.1.1.11.1.2INTEGER {manual(1), adapt-at-init(2), dynamic(3)}read-createcurrent
zhoneVdslLineConfUpRateMode
OBJECT-TYPE
Specifies the rate selection behavior for the line in the upstream direction. manual(1) forces the rate to the configured rate adaptAtInit(2) adapts the line at initialization only dynamic(3) adapts the line at initialization and showtime
1.3.6.1.4.1.5504.5.13.1.1.11.1.3INTEGER {manual(1), adapt-at-init(2), dynamic(3)}read-createcurrent
zhoneVdslLineConfDownMaxPwr
OBJECT-TYPE
Specifies the maximum aggregate downstream power level in the range -5.0 to 20.0 dBm.
1.3.6.1.4.1.5504.5.13.1.1.11.1.4Integer32 (-50..200)read-createcurrent
zhoneVdslLineConfUpMaxPwr
OBJECT-TYPE
Specifies the maximum aggregate upstream power level in the range -13.0 to 20.0 dBm.
1.3.6.1.4.1.5504.5.13.1.1.11.1.5Integer32 (-130..200)read-createcurrent
zhoneVdslLineConfDownMaxSnrMgn
OBJECT-TYPE
Specifies the maximum downstream Signal/Noise Margin in units of 0.10 dB, for a range of 0 to 31.0 dB.
1.3.6.1.4.1.5504.5.13.1.1.11.1.6Unsigned32 (0..310)read-createcurrent
zhoneVdslLineConfDownMinSnrMgn
OBJECT-TYPE
Specifies the minimum downstream Signal/Noise Margin in units of 0.10 dB, for a range of 0 to 31.0 dB.
1.3.6.1.4.1.5504.5.13.1.1.11.1.7Unsigned32 (0..310)read-createcurrent
zhoneVdslLineConfDownTargetSnrMgn
OBJECT-TYPE
Specifies the target downstream Signal/Noise Margin in units of 0.10 dB, for a range of 0 to 31.0 dB. This is the Noise Margin the transceivers must achieve with a BER of 10^-7 or better to successfully complete initialization.
1.3.6.1.4.1.5504.5.13.1.1.11.1.8Unsigned32 (0..310)read-createcurrent
zhoneVdslLineConfUpMaxSnrMgn
OBJECT-TYPE
Specifies the maximum upstream Signal/Noise Margin in units of 0.10 dB, for a range of 0 to 31.0 dB.
1.3.6.1.4.1.5504.5.13.1.1.11.1.9Unsigned32 (0..310)read-createcurrent
zhoneVdslLineConfUpMinSnrMgn
OBJECT-TYPE
Specifies the minimum upstream Signal/Noise Margin in units of 0.10 dB, for a range of 0 to 31.0 dB.
1.3.6.1.4.1.5504.5.13.1.1.11.1.10Unsigned32 (0..310)read-createcurrent
zhoneVdslLineConfUpTargetSnrMgn
OBJECT-TYPE
Specifies the target upstream Signal/Noise Margin in units of 0.10 dB, for a range of 0 to 31.0 dB. This is the Noise Margin the transceivers must achieve with a BER of 10^-7 or better to successfully complete initialization.
1.3.6.1.4.1.5504.5.13.1.1.11.1.11Unsigned32 (0..310)read-createcurrent
zhoneVdslLineConfDownFastMaxDataRate
OBJECT-TYPE
Specifies the maximum downstream fast channel data rate in steps of 1000 bits/second.
1.3.6.1.4.1.5504.5.13.1.1.11.1.12Unsigned32 (0..200000)read-createcurrent
zhoneVdslLineConfDownFastMinDataRate
OBJECT-TYPE
Specifies the minimum downstream fast channel data rate in steps of 1000 bits/second.
1.3.6.1.4.1.5504.5.13.1.1.11.1.13Unsigned32 (0..200000)read-createcurrent
zhoneVdslLineConfDownSlowMaxDataRate
OBJECT-TYPE
Specifies the maximum downstream slow channel data rate in steps of 1000 bits/second. The maximum aggregate downstream transmit speed of the line can be derived from the sum of maximum downstream fast and slow channel data rates.
1.3.6.1.4.1.5504.5.13.1.1.11.1.14Unsigned32 (0..200000)read-createcurrent
zhoneVdslLineConfDownSlowMinDataRate
OBJECT-TYPE
Specifies the minimum downstream slow channel data rate in steps of 1000 bits/second. The minimum aggregate downstream transmit speed of the line can be derived from the sum of minimum downstream fast and slow channel data rates.
1.3.6.1.4.1.5504.5.13.1.1.11.1.15Unsigned32 (0..200000)read-createcurrent
zhoneVdslLineConfUpFastMaxDataRate
OBJECT-TYPE
Specifies the maximum upstream fast channel data rate in steps of 1000 bits/second. The maximum aggregate upstream transmit speed of the line can be derived from the sum of maximum upstream fast and slow channel data rates.
1.3.6.1.4.1.5504.5.13.1.1.11.1.16Unsigned32 (0..200000)read-createcurrent
zhoneVdslLineConfUpFastMinDataRate
OBJECT-TYPE
Specifies the minimum upstream fast channel data rate in steps of 1000 bits/second. The minimum aggregate upstream transmit speed of the line can be derived from the sum of minimum upstream fast and slow channel data rates.
1.3.6.1.4.1.5504.5.13.1.1.11.1.17Unsigned32 (0..200000)read-createcurrent
zhoneVdslLineConfUpSlowMaxDataRate
OBJECT-TYPE
Specifies the maximum upstream slow channel data rate in steps of 1000 bits/second.
1.3.6.1.4.1.5504.5.13.1.1.11.1.18Unsigned32 (0..200000)read-createcurrent
zhoneVdslLineConfUpSlowMinDataRate
OBJECT-TYPE
Specifies the minimum upstream slow channel data rate in steps of 1000 bits/second.
1.3.6.1.4.1.5504.5.13.1.1.11.1.19Unsigned32 (0..200000)read-createcurrent
zhoneVdslLineConfDownRateRatio
OBJECT-TYPE
For dynamic rate adaptation at startup, the allocation of data rate in excess of the minimum data rate for each channel is controlled by the object. This object specifies the ratio of the allocation of the excess data rate between the fast and the slow channels. This allocation represents downstream Fast Channel Allocation / Slow Channel Allocation.
1.3.6.1.4.1.5504.5.13.1.1.11.1.20Unsigned32 (0..100)read-createcurrent
zhoneVdslLineConfUpRateRatio
OBJECT-TYPE
For dynamic rate adaptation at startup, the allocation of data rate in excess of the minimum data rate for each channel is controlled by the object. This object specifies the ratio of the allocation of the excess data rate between the fast and the slow channels. This allocation represents upstream Fast Channel Allocation/Slow Channel Allocation.
1.3.6.1.4.1.5504.5.13.1.1.11.1.21Unsigned32 (0..100)read-createcurrent
zhoneVdslLineConfDownMaxInterDelay
OBJECT-TYPE
Specifies the maximum interleave delay for the downstream slow channel.
1.3.6.1.4.1.5504.5.13.1.1.11.1.22Unsigned32 (0..255)read-createcurrent
zhoneVdslLineConfUpMaxInterDelay
OBJECT-TYPE
Specifies the maximum interleave delay for the upstream slow channel.
1.3.6.1.4.1.5504.5.13.1.1.11.1.23Unsigned32 (0..255)read-createcurrent
zhoneVdslLineConfDownPboControl
OBJECT-TYPE
Downstream power backoff (PBO) control for this line. For transceivers which do not support downstream PBO control, this object MUST be fixed at disabled(1). If auto(2) is selected, the transceiver will automatically adjust the power backoff. If manual(3) is selected, then the transceiver will use the value from zhoneVdslLineConfDownPboLevel.
1.3.6.1.4.1.5504.5.13.1.1.11.1.24INTEGER {disabled(1), auto(2), manual(3)}read-createcurrent
zhoneVdslLineConfUpPboControl
OBJECT-TYPE
Upstream power backoff (PBO) control for this line. For transceivers which do not support upstream PBO control, this object MUST be fixed at disabled(1). If auto(2) is selected, the transceiver will automatically adjust the power backoff. If manual(3) is selected, then the transceiver will use the value from zhoneVdslLineConfUpPboLevel.
1.3.6.1.4.1.5504.5.13.1.1.11.1.25INTEGER {disabled(1), auto(2), manual(3)}read-createcurrent
zhoneVdslLineConfDownPboLevel
OBJECT-TYPE
Specifies the downstream backoff level to be used when vdslLineConfDownPboControl = manual(3).
1.3.6.1.4.1.5504.5.13.1.1.11.1.26Unsigned32 (0..160)read-createcurrent
zhoneVdslLineConfUpPboLevel
OBJECT-TYPE
Specifies the upstream backoff level to be used when vdslLineConfUpPboControl = manual(3).
1.3.6.1.4.1.5504.5.13.1.1.11.1.27Unsigned32 (0..160)read-createcurrent
zhoneVdslLineConfDeploymentScenario
OBJECT-TYPE
The VDSL line deployment scenario. When using fttCab(1), the VTU-C is located in a street cabinet. When using fttEx(2), the VTU-C is located at the central office. Changes to this value will have no effect on the transceiver.
1.3.6.1.4.1.5504.5.13.1.1.11.1.28INTEGER {fttCab(1), fttEx(2), other(3)}read-createcurrent
zhoneVdslLineConfAdslPresence
OBJECT-TYPE
Indicates presence of ADSL service in the associated cable bundle/binder. none(1) indicates no ADSL service in the bundle adslOverPots(2) indicates ADSL service over POTS is present in the bundle adslOverISDN(3) indicates ADSL service over ISDN is present in the bundle
1.3.6.1.4.1.5504.5.13.1.1.11.1.29INTEGER {none(1), adslOverPots(2), adslOverISDN(3)}read-createcurrent
zhoneVdslLineConfApplicableStandard
OBJECT-TYPE
The VDSL standard to be used for the line. ansi(1) indicates ANSI standard etsi(2) indicates ETSI standard itu(3) indicates ITU standard other(4) indicates a standard other than the above.
1.3.6.1.4.1.5504.5.13.1.1.11.1.30INTEGER {ansi(1), etsi(2), itu(3), other(4)}read-createcurrent
zhoneVdslLineConfBandPlan
OBJECT-TYPE
The VDSL band plan to be used for the line. bandPlan997(1) is to be used for ITU-T G.993.1 Bandplan-B ETSI Bandplan ANSI Plan 997 bandPlan998(2) is to be used for ITU-T G.993.1 Bandplan-A ANSI Plan 998 bandPlanFx(3) is to be used for ITU-T G.993.1 Bandplan-C. other(4) is to be used for non-standard bandplans. If this object is set to bandPlanFx(3), then the object vdslLineConfBandPlanFx MUST also be set.
1.3.6.1.4.1.5504.5.13.1.1.11.1.31INTEGER {bandPlan997(1), bandPlan998(2), bandPlanFx(3), other(4), bandPlan997-2(5), bandPlan997-3(6), bandPlan998-2(7), bandPlan998-3(8), bandPlan998-17-6(9), fx-2(10), fx-3(11), china-a-2(12), china-a-3(13), china-b-2(14), china-b-3(15)}read-createcurrent
zhoneVdslLineConfBandPlanFx
OBJECT-TYPE
The frequency limit between bands D2 and U2 when zhoneVdslLineConfBandPlan is set to bandPlanFx(3).
1.3.6.1.4.1.5504.5.13.1.1.11.1.32Unsigned32 (3750..12000)read-createcurrent
zhoneVdslLineConfBandOptUsage
OBJECT-TYPE
Defines the VDSL link use of the optional frequency range [25kHz - 138kHz] (Opt). unused(1) indicates Opt is unused upstream(2) indicates Opt usage is for upstream downstream(3) indicates Opt usage is for downstream. upstreamForced(4) indicates forced upstream
1.3.6.1.4.1.5504.5.13.1.1.11.1.33INTEGER {unused(1), upstream(2), downstream(3), upstream-forced(4)}read-createcurrent
zhoneVdslLineConfUpPsdTemplate
OBJECT-TYPE
This object has been modified by Zhone. The upstream PSD template to be used for the line. Here, templateMask1(1) refers to a notched mask that limits the transmitted PSD within the internationally standardized HAM (Handheld Amateur Radio) radio bands, while templateMask2(2) refers to an unnotched mask. The masks themselves depend upon the applicable standard being used (vdslLineConfApplicableStandard).
1.3.6.1.4.1.5504.5.13.1.1.11.1.34INTEGER {ansi-fftex-m1(3), ansi-fftex-m2(4), ansi-fftcab-m1(5), fftcab-m2(6), etsi-m1(7), etsi-m2(8), psd-custom(9)}read-createcurrent
zhoneVdslLineConfDownPsdTemplate
OBJECT-TYPE
This object has been modified by Zhone. The downstream PSD template to be used for the line. Here, templateMask1(1) refers to a notched mask that limits the transmitted PSD within the internationally standardized HAM (Handheld Amateur Radio) radio bands, while templateMask2(2) refers to an unnotched mask. The masks themselves depend upon the applicable standard being used (vdslLineConfApplicableStandard).
1.3.6.1.4.1.5504.5.13.1.1.11.1.35INTEGER {ansi-fftex-m1(3), ansi-fftex-m2(4), ansi-fftcab-m1(5), fftcab-m2(6), fftcab-m1-adsl(7), fftcab-m1-adslplus(8), fftcab-m2-adsl(9), fftcab-m2-adslplus(10), etsi-pexp1-m1(11), etsi-pexp1-m2(12), etsi-pexp2-m1(13), etsi-pexp2-m2(14), psd-custom(15), etsi-pexm2-sample1(16), etsi-pexm2-sample2(17), etsi-pexm2-sample3(18), etsi-pexm2-sample4(19), etsi-pcab-m1(20), etsi-pcab-m2(21)}read-createcurrent
zhoneVdslLineConfHamBandMask
OBJECT-TYPE
The transmit power spectral density mask code, used to avoid interference with HAM (Handheld Amateur Radio) radio bands by introducing power control (notching) in one or more of these bands. Amateur radio band notching is defined in the VDSL spectrum as follows: Band Start Frequency Stop Frequency ---- ------------------ -------------------------------- 30m 1810 kHz 2000 kHz 40m 3500 kHz 3800 kHz (ETSI); 4000 kHz (ANSI) 80m 7000 kHz 7100 kHz (ETSI); 7300 kHz (ANSI) 160m 10100 kHz 10150 kHz Notching for each standard band can be enabled or disabled via the bit mask. Two custom notches may be specified. If either of these are enabled via the bit mask, then the following objects MUST be specified: If customNotch1 is enabled, then both zhoneVdslLineConfCustomNotch1Start zhoneVdslLineConfCustomNotch1Stop MUST be specified. If customNotch2 is enabled, then both zhoneVdslLineConfCustomNotch2Start zhoneVdslLineConfCustomNotch2Stop MUST be specified.
1.3.6.1.4.1.5504.5.13.1.1.11.1.36Bits {customNotch1(0), customNotch2(1), amateurBand30m(2), amateurBand40m(3), amateurBand80m(4), amateurBand160m(5)}read-createcurrent
zhoneVdslLineConfCustomNotch1Start
OBJECT-TYPE
Specifies the start frequency of custom HAM (Handheld Amateur Radio) notch 1. zhoneVdslLineConfCustomNotch1Start MUST be less than or equal to vdslLineConfCustomNotch1Stop.
1.3.6.1.4.1.5504.5.13.1.1.11.1.37Unsigned32read-createcurrent
zhoneVdslLineConfCustomNotch1Stop
OBJECT-TYPE
Specifies the stop frequency of custom HAM (Handheld Amateur Radio) notch 1. zhoneVdslLineConfCustomNotch1Stop MUST be greater than or equal to vdslLineConfCustomNotch1Start.
1.3.6.1.4.1.5504.5.13.1.1.11.1.38Unsigned32read-createcurrent
zhoneVdslLineConfCustomNotch2Start
OBJECT-TYPE
Specifies the start frequency of custom HAM (Handheld Amateur Radio) notch 2. zhoneVdslLineConfCustomNotch2Start MUST be less than or equal to vdslLineConfCustomNotch2Stop.
1.3.6.1.4.1.5504.5.13.1.1.11.1.39Unsigned32read-createcurrent
zhoneVdslLineConfCustomNotch2Stop
OBJECT-TYPE
Specifies the stop frequency of custom HAM (Handheld Amateur Radio) notch 2. zhoneVdslLineConfCustomNotch2Stop MUST be greater than or equal to vdslLineConfCustomNotch2Start.
1.3.6.1.4.1.5504.5.13.1.1.11.1.40Unsigned32read-createcurrent
zhoneVdslLineConfDownTargetSlowBurst
OBJECT-TYPE
Specifies the target level of impulse noise (burst) protection for an interleaved (slow) channel.
1.3.6.1.4.1.5504.5.13.1.1.11.1.41Unsigned32 (0..1275)read-createcurrent
zhoneVdslLineConfUpTargetSlowBurst
OBJECT-TYPE
Specifies the target level of impulse noise (burst) protection for an interleaved (slow) channel.
1.3.6.1.4.1.5504.5.13.1.1.11.1.42Unsigned32 (0..1275)read-createcurrent
zhoneVdslLineConfDownMaxFastFec
OBJECT-TYPE
This parameter provisions the maximum level of Forward Error Correction (FEC) redundancy related overhead to be maintained for a fast channel.
1.3.6.1.4.1.5504.5.13.1.1.11.1.43Unsigned32 (0..50)read-createcurrent
zhoneVdslLineConfUpMaxFastFec
OBJECT-TYPE
This parameter provisions the maximum level of Forward Error Correction (FEC) redundancy related overhead to be maintained for a fast channel.
1.3.6.1.4.1.5504.5.13.1.1.11.1.44Unsigned32 (0..50)read-createcurrent
zhoneVdslLineConfLineType
OBJECT-TYPE
This parameter provisions the VDSL physical entity at start-up by defining whether and how the line will be channelized, i.e., which channel type(s) are supported. If the line is to be channelized, the value will be other than noChannel(1). This configuration can be activated only during start-up. Afterwards, the value of zhoneVdslLineType coincides with the value of zhoneVdslLineConfLineType. Depending on this value, the corresponding entries in the ifTable for the interleaved and the fast channels are enabled or disabled according to the value of their ifOperStatus. Defined values are: noChannel(1) -- no channels exist fastOnly(2) -- only fast channel exists interleavedOnly(3) -- only interleaved channel exists fastOrInterleaved(4) -- either fast or interleaved channel -- exists, but only one at a time fastAndInterleaved(5) -- both fast and interleaved channels -- exist Note that 'slow' and 'interleaved' refer to the same channel.
1.3.6.1.4.1.5504.5.13.1.1.11.1.45INTEGER {noChannel(1), fastOnly(2), interleavedOnly(3), fastOrInterleaved(4), fastAndInterleaved(5)}read-createcurrent
zhoneVdslLineConfProfRowStatus
OBJECT-TYPE
This object is used to create a new row or modify or delete an existing row in this table. A profile activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'outOfService'), it must be first unreferenced from all associated lines. An 'active' profile may be modified at any time. Note that some changes may require that any referenced lines be restarted (e.g., zhoneVdslLineConfLineType).
1.3.6.1.4.1.5504.5.13.1.1.11.1.47RowStatusread-createcurrent
zhoneVdslLineConfTransmissionMode
OBJECT-TYPE
The transmission standard to be used for the line.
1.3.6.1.4.1.5504.5.13.1.1.11.1.48INTEGER {autoNegotiateMode(1), vdslMode(2), vdsl2Mode(3), adsl2PlusMode(4), adsl2Mode(5), gdmtMode(6)}read-createcurrent
zhoneVdslLineConfVdsl2Profile
OBJECT-TYPE
The VDSL2 standard to be used for the line.
1.3.6.1.4.1.5504.5.13.1.1.11.1.49INTEGER {g993-2-8a(1), g993-2-8b(2), g993-2-8c(3), g993-2-8d(4), g993-2-12a(5), g993-2-12b(6), g993-2-17a(7), g993-2-30a(8)}read-createcurrent
zhoneVdslLineConfVdslMode
OBJECT-TYPE
Controls which VDSL modes are available on the line.
1.3.6.1.4.1.5504.5.13.1.1.11.1.50INTEGER {standard(1), long-reach-8k(2), r8k(3), std-8k(4), lr-8k(5), std-lr(6), std-lr-8k(7)}read-createcurrent
zhoneVdslLineConfPboElectricalOverride
OBJECT-TYPE
Override electrical length estimated by VUTU_C. The special value 256 means do not perform override.
1.3.6.1.4.1.5504.5.13.1.1.11.1.51Integer32 (0..256)read-createcurrent
zhoneVdslLineConfAutoModeCrtrn
OBJECT-TYPE
Determines the policy to select optimal mode of oepration.
1.3.6.1.4.1.5504.5.13.1.1.11.1.52INTEGER {crtrn-chip-prop(1), optimize-us(2), optimize-ds(3)}read-createcurrent
zhoneVdslLineConfNetworkTimingRef
OBJECT-TYPE
Enable/disable reference clock source.
1.3.6.1.4.1.5504.5.13.1.1.11.1.53INTEGER {enable(1), disable(2)}read-onlycurrent
zhoneVdslLineConfAdslBandMode
OBJECT-TYPE
Specifies whether the XDSL can use the ADSL spectrum or not.
1.3.6.1.4.1.5504.5.13.1.1.11.1.54INTEGER {allowed(1), not-allowed(2)}read-createcurrent
zhoneVdslLineConfAdslBandModeEndFreq
OBJECT-TYPE
Specifies the ADSL band end frequency when the ADSL band usage is not allowed.
1.3.6.1.4.1.5504.5.13.1.1.11.1.55Integer32 (276..2208)read-createcurrent
zhoneVdslLineConfSeltEchoMeasurementTime
OBJECT-TYPE
Contains the SELT echo measurement time
1.3.6.1.4.1.5504.5.13.1.1.11.1.56Integer32 (5..240)read-createcurrent
zhoneVdslLineConfSeltNoiseMeasurementTime
OBJECT-TYPE
Contains the SELT noise measurement time.
1.3.6.1.4.1.5504.5.13.1.1.11.1.57Integer32 (5..240)read-createcurrent
zhoneVdslLineConfSeltAgc
OBJECT-TYPE
Contains the SELT AGC gain value.
1.3.6.1.4.1.5504.5.13.1.1.11.1.58Integer32 (-100..100)read-createcurrent
zhoneVdslLineConfDownTrellis
OBJECT-TYPE
Enables/disables downstream Trellis coding.
1.3.6.1.4.1.5504.5.13.1.1.11.1.59INTEGER {enable(1), disable(2)}read-createcurrent
zhoneVdslLineConfUpTrellis
OBJECT-TYPE
Enables/disables upstream Trellis coding.
1.3.6.1.4.1.5504.5.13.1.1.11.1.60INTEGER {enable(1), disable(2)}read-createcurrent
zhoneVdslLineConfDownMaxAggregateTxPwr
OBJECT-TYPE
Maximum total power that is allowed to be transmitted in the downstream direction.
1.3.6.1.4.1.5504.5.13.1.1.11.1.61INTEGER {unlimited(4)}read-createcurrent
zhoneVdslLineConfUpMaxAggregateTxPwr
OBJECT-TYPE
Maximum total power that is allowed to be transmitted in the upstream direction.
1.3.6.1.4.1.5504.5.13.1.1.11.1.62INTEGER {unlimited(4)}read-createcurrent
zhoneVdslLineConfDownMaxPsd
OBJECT-TYPE
The maximum power spectral density level allowed on the line at the transmitter output downstream for initialization and showtime signals.
1.3.6.1.4.1.5504.5.13.1.1.11.1.63Integer32 (-955..0)read-createcurrent
zhoneVdslLineConfUpMaxPsd
OBJECT-TYPE
The maximum power spectral density level allowed on the line at the transmitter output upstream for initialization and showtime signals.
1.3.6.1.4.1.5504.5.13.1.1.11.1.64Integer32 (-955..0)read-createcurrent
zhoneVdslLineConfDownPsdShape
OBJECT-TYPE
Maximum transmit PSD allowed in the downstream channel on a VDSL2 line.
1.3.6.1.4.1.5504.5.13.1.1.11.1.65INTEGER {custom-psd(1), region-a-psd(2), region-c-psd(3), region-b-m1-a-psd(4), region-b-m1-b-psd(5), region-b-m1-us0-psd(6), region-b-m2-a-psd(7), region-b-m2-m-psd(8), region-b-m2-b-psd(9), region-b-m2-us0-psd(10)}read-createcurrent
zhoneVdslLineConfUpPsdShape
OBJECT-TYPE
Maximum transmit PSD allowed in the upstream channel on a VDSL2 line.
1.3.6.1.4.1.5504.5.13.1.1.11.1.66INTEGER {custom-psd(1), region-a-psd(2), region-c-psd(3), region-b-m1-a-psd(4), region-b-m1-b-psd(5), region-b-m1-us0-psd(6), region-b-m2-a-psd(7), region-b-m2-m-psd(8), region-b-m2-b-psd(9), region-b-m2-us0-psd(10)}read-createcurrent
zhoneVdslLineConfDownVirtualNoiseSnrMode
OBJECT-TYPE
Downstream virtual noise SNR mode on a VDSL2 line.
1.3.6.1.4.1.5504.5.13.1.1.11.1.67INTEGER {mode1(1), mode2(2), mode3(3)}read-createcurrent
zhoneVdslLineConfUpVirtualNoiseSnrMode
OBJECT-TYPE
Upstream virtual noise SNR mode on a VDSL2 line.
1.3.6.1.4.1.5504.5.13.1.1.11.1.68INTEGER {mode1(1), mode2(2), mode3(3)}read-createcurrent
zhoneVdslLineConfDownErasureDetectionFast
OBJECT-TYPE
Indicates whether the erasure detection mechanism should be enabled or disabled in the downstream fast channel.
1.3.6.1.4.1.5504.5.13.1.1.11.1.69INTEGER {enable(1), disable(2)}read-createcurrent
zhoneVdslLineConfUpErasureDetectionFast
OBJECT-TYPE
Indicates whether the erasure detection mechanism should be enabled or disabled in the downstream fast channel.
1.3.6.1.4.1.5504.5.13.1.1.11.1.70INTEGER {enable(1), disable(2)}read-createcurrent
zhoneVdslLineConfDownErasureDetectionInterleave
OBJECT-TYPE
Indicates whether the erasure detection mechanism should be enabled or disabled in the downstream slow channel (interleave).
1.3.6.1.4.1.5504.5.13.1.1.11.1.71INTEGER {enable(1), disable(2)}read-createcurrent
zhoneVdslLineConfUpErasureDetectionInterleave
OBJECT-TYPE
Indicates whether the erasure detection mechanism should be enabled or disabled in the uptream slow channel (interleave).
1.3.6.1.4.1.5504.5.13.1.1.11.1.72INTEGER {enable(1), disable(2)}read-createcurrent
zhoneVdslLineConfDownGhsA43TonePwr
OBJECT-TYPE
Determines the mode of the downstream tones power used during handshake, during A43 mode.
1.3.6.1.4.1.5504.5.13.1.1.11.1.73INTEGER {default(1), auto(2), manual(3)}read-createcurrent
zhoneVdslLineConfDownGhsB43TonePwr
OBJECT-TYPE
Determines the mode of the downstream tones power used during handshake, during B43 mode.
1.3.6.1.4.1.5504.5.13.1.1.11.1.74INTEGER {default(1), auto(2), manual(3)}read-createcurrent
zhoneVdslLineConfDownGhsA43cTonePwr
OBJECT-TYPE
Determines the mode of the downstream tones power used during handshake, during A43c mode.
1.3.6.1.4.1.5504.5.13.1.1.11.1.75INTEGER {default(1), auto(2), manual(3)}read-createcurrent
zhoneVdslLineConfDownGhsV43TonePwr
OBJECT-TYPE
Determines the mode of the downstream tone power used during handshake, during V43 mode.
1.3.6.1.4.1.5504.5.13.1.1.11.1.76INTEGER {default(1), auto(2), manual(3)}read-createcurrent
zhoneVdslLineConfDownGhsA43TonePwrMaxLvl
OBJECT-TYPE
Determines the maximum power of downstream tones used, in manual mode, during handshake in A43 mode. A value of -99 indicates no power used.
1.3.6.1.4.1.5504.5.13.1.1.11.1.77Integer32 (-99..-40)read-createcurrent
zhoneVdslLineConfDownGhsB43TonePwrMaxLvl
OBJECT-TYPE
Determines the maximum power of downstream tones used, in manual mode, during handshake in B43 mode. A value of -99 indicates no power used.
1.3.6.1.4.1.5504.5.13.1.1.11.1.78Integer32 (-99..-40)read-createcurrent
zhoneVdslLineConfDownGhsA43cTonePwrMaxLvl
OBJECT-TYPE
Determines the maximum power of downstream tones used, in manual mode, during handshake in A43c mode. A value of -99 indicates no power used.
1.3.6.1.4.1.5504.5.13.1.1.11.1.79Integer32 (-99..-40)read-createcurrent
zhoneVdslLineConfDownGhsV43TonePwrMaxLvl
OBJECT-TYPE
Determines the maximum power of downstream tones used, in manual mode, during handshake in V43 mode. A value of -99 indicates no power used.
1.3.6.1.4.1.5504.5.13.1.1.11.1.80Integer32 (-99..-40)read-createcurrent
zhoneVdslLineConfDownRsCoding
OBJECT-TYPE
Parameter to enable/disable RS Coding in downstream channel.
1.3.6.1.4.1.5504.5.13.1.1.11.1.81INTEGER {enable(1), disable(2)}read-createcurrent
zhoneVdslLineConfUpRsCoding
OBJECT-TYPE
Parameter to enable/disable RS Coding in upsream channel.
1.3.6.1.4.1.5504.5.13.1.1.11.1.82INTEGER {enable(1), disable(2)}read-createcurrent
zhoneVdslLineConfUpPboPsdTemplate
OBJECT-TYPE
Specifies the maximum received PSD allowed in the upstream channel on the VDSLx line.
1.3.6.1.4.1.5504.5.13.1.1.11.1.83INTEGER {ansi-a(1), ansi-f(2), etsi-a(3), etsi-b(4), etsi-c(5), etsi-d(6), etsi-e(7), etsi-f(8), custom(9), ab-param(10)}read-createcurrent
zhoneVdslLineConfUpPboPsdParamA1
OBJECT-TYPE
Upstream power backoff PSD parameter A1. This parameter is only used if the mask selection is set to PSDMaskABParameters
1.3.6.1.4.1.5504.5.13.1.1.11.1.84Integer32 (4000..8589)read-createcurrent
zhoneVdslLineConfUpPboPsdParamA2
OBJECT-TYPE
Upstream power backoff PSD parameter A2. This parameter is only used if the mask selection is set to PSDMaskABParameters
1.3.6.1.4.1.5504.5.13.1.1.11.1.85Integer32 (4000..8589)read-createcurrent
zhoneVdslLineConfUpPboPsdParamB1
OBJECT-TYPE
Upstream power backoff PSD parameter B1. This parameter is only used if the mask selection is set to PSDMaskABParameters
1.3.6.1.4.1.5504.5.13.1.1.11.1.86Integer32 (0..8589)read-createcurrent
zhoneVdslLineConfUpPboPsdParamB2
OBJECT-TYPE
Upstream power backoff PSD parameter B2. This parameter is only used if the mask selection is set to PSDMaskABParameters
1.3.6.1.4.1.5504.5.13.1.1.11.1.87Integer32 (0..8589)read-createcurrent
zhoneVdslLineConfDownDownshiftSnrMgn
OBJECT-TYPE
Configured Signal/Noise Margin for rate downshift. If the noise margin falls below this level, the modem should attempt to decrease its transmit rate.
1.3.6.1.4.1.5504.5.13.1.1.11.1.88Integer32 (0..310)read-createcurrent
zhoneVdslLineConfDownUpshiftSnrMgn
OBJECT-TYPE
Configured Signal/Noise Margin for rate upshift. If the noise margin rises above this level, the modem should attempt to increase its transmit rate.
1.3.6.1.4.1.5504.5.13.1.1.11.1.89Integer32 (0..310)read-createcurrent
zhoneVdslLineConfDownMinDownshiftTime
OBJECT-TYPE
Minimum time that the current margin is below DownshiftSnrMgn before a downshift occurs.
1.3.6.1.4.1.5504.5.13.1.1.11.1.90Integer32 (0..16383)read-createcurrent
zhoneVdslLineConfDownMinUpshiftTime
OBJECT-TYPE
Minimum time that the current margin is above UpshiftSnrMgn before an upshift occurs.
1.3.6.1.4.1.5504.5.13.1.1.11.1.91Integer32 (0..16383)read-createcurrent
zhoneVdslLineConfUpDownshiftSnrMgn
OBJECT-TYPE
Configured Signal/Noise Margin for rate downshift. If the noise margin falls below this level, the modem should attempt to decrease its transmit rate.
1.3.6.1.4.1.5504.5.13.1.1.11.1.92Integer32 (0..310)read-createcurrent
zhoneVdslLineConfUpUpshiftSnrMgn
OBJECT-TYPE
Configured Signal/Noise Margin for rate upshift. If the noise margin rises above this level, the modem should attempt to increase its transmit rate.
1.3.6.1.4.1.5504.5.13.1.1.11.1.93Integer32 (0..310)read-createcurrent
zhoneVdslLineConfUpMinDownshiftTime
OBJECT-TYPE
Minimum time that the current margin is below DownshiftSnrMgn before a downshift occurs.
1.3.6.1.4.1.5504.5.13.1.1.11.1.94Integer32 (0..16383)read-createcurrent
zhoneVdslLineConfUpMinUpshiftTime
OBJECT-TYPE
Minimum time that the current margin is above UpshiftSnrMgn before an upshift occurs.
1.3.6.1.4.1.5504.5.13.1.1.11.1.95Integer32 (0..16383)read-createcurrent
zhoneVdslLineConfDownMinTxThresholdAlarm
OBJECT-TYPE
Minimum CO Tx Sync rate threshold alarm. If set to 0, this field is disregarded. Otherwise, if Tx Sync rate falls below this value, a trap and alarm will be issued
1.3.6.1.4.1.5504.5.13.1.1.11.1.96Unsigned32 (0..200000)read-createcurrent
zhoneVdslLineConfUpMinTxThresholdAlarm
OBJECT-TYPE
Minimum CPE Tx Sync rate threshold alarm. If set to 0, this field is disregarded. Otherwise, if Tx Sync rate falls below this value, a trap and alarm will be issued
1.3.6.1.4.1.5504.5.13.1.1.11.1.97Unsigned32 (0..200000)read-createcurrent
zhoneVdslLineConfPotsBypassRelayMaxDuration
OBJECT-TYPE
The maximum duration in seconds that an Adsl Pots Low Pass Filter Bypass Relay will remain active (meaning closed/energized). As a fail-safe mechanism, the relay will automatically return a line back to normal operational mode when this timer has expired. This object is only valid for Adsl Pots Splitter cards containing the Pots LPF Bypass Relays.
1.3.6.1.4.1.5504.5.13.1.1.11.1.98INTEGER (1..300)read-createcurrent
zhoneVdslLineConfDMTConfMode
OBJECT-TYPE
Discrete Multi-Tone parameter that selects whether there is overlap (echoCancel) or no overlap (freqDivMux) of bins.
1.3.6.1.4.1.5504.5.13.1.1.11.1.99INTEGER {echocancel(1), freqdivmux(2)}read-createcurrent
zhoneVdslLineConfDownBitSwap
OBJECT-TYPE
Enable or disable downstream bit swap.
1.3.6.1.4.1.5504.5.13.1.1.11.1.100INTEGER {disabled(1), enabled(2)}read-createcurrent
zhoneVdslLineConfUpBitSwap
OBJECT-TYPE
Enable or disable upstream bit swap.
1.3.6.1.4.1.5504.5.13.1.1.11.1.101INTEGER {disabled(1), enabled(2)}read-createcurrent
zhoneVdslLineConfAdslAnnexMModeEnabled
OBJECT-TYPE
This object indicates whether Annex-M mode is enabled on the Adsl modem. If this object is set to 'true' then Annex-M mode is enabled. If it is set to 'false then Annex-M mode is disabled.
1.3.6.1.4.1.5504.5.13.1.1.11.1.102TruthValueread-createcurrent
zhoneVdslLineConfAdslAnnexMPsdMask
OBJECT-TYPE
This object specifies the maximum transmit PSD allowed in the downstream channel on an BIS Annex-M line.
1.3.6.1.4.1.5504.5.13.1.1.11.1.103INTEGER {eu64(1), eu60(2), eu56(3), eu52(4), eu48(5), eu44(6), eu40(7), eu36(8), eu32(9), all(10)}read-createcurrent
zhoneVdslLineConfUs0BoundaryTone
OBJECT-TYPE
This object configures the upper boundary of US0. US0 is used in long reach mode when there is no more capacity in US1. The switchover is typically around 3500 feet.
1.3.6.1.4.1.5504.5.13.1.1.11.1.104INTEGER {d32(1), d36(2), d40(3), d44(4), d48(5), d52(6), d56(7), d64(8)}read-createcurrent
zhoneVdslLineConfDownInp
OBJECT-TYPE
The minimum impulse noise protection for the downstream bearer channel expressed in symbols. One symbol equals 250 uS.
1.3.6.1.4.1.5504.5.13.1.1.11.1.105INTEGER {noProtection(1), halfSymbol(2), singleSymbol(3), twoSymbols(4), threeSymbols(5), fourSymbols(6), fiveSymbols(7), sixSymbols(8), sevenSymbols(9), eightSymbols(10), nineSymbols(11), tenSymbols(12), elevenSymbols(13), twelveSymbols(14), thirteenSymbols(15), fourteenSymbols(16), fifteenSymbols(17), sixteenSymbols(18)}read-createcurrent
zhoneVdslLineConfUpInp
OBJECT-TYPE
The minimum impulse noise protection for the upstream bearer channel expressed in symbols. One symbol equals 250 uS.
1.3.6.1.4.1.5504.5.13.1.1.11.1.106INTEGER {noProtection(1), halfSymbol(2), singleSymbol(3), twoSymbols(4), fourSymbols(5), eightSymbols(6), sixteenSymbols(7), threeSymbols(8), fiveSymbols(9), sixSymbols(10), sevenSymbols(11), nineSymbols(12), tenSymbols(13), elevenSymbols(14), twelveSymbols(15), thirteenSymbols(16), fourteenSymbols(17), fifteenSymbols(18)}read-createcurrent
zhoneVdslLineConfDownMaxInterleavingDelay
OBJECT-TYPE
The maximum inteleaving delay in the downstream direction. A value of zero indicates no delay introduced.
1.3.6.1.4.1.5504.5.13.1.1.11.1.107INTEGER (0..63)read-createcurrent
zhoneVdslLineConfUpMaxInterleavingDelay
OBJECT-TYPE
The maximum inteleaving delay in the upstream direction. A value of zero indicates no delay introduced.
1.3.6.1.4.1.5504.5.13.1.1.11.1.108INTEGER (0..63)read-createcurrent
zhoneVdslLineConfDownPsdMaskEnable
OBJECT-TYPE
This object selects the Psd Mask in the downstream direction. 'standard' : use the PSD Mask specified in the object zhoneVdslLineConfDownPsdSelect 'mod' : use the pre-defined Mask-On-Demand PSD Mask 'modFallback': use the pre-defined Mask-On-Demand PSD Mask with fallback
1.3.6.1.4.1.5504.5.13.1.1.11.1.109INTEGER {standard(2), mod(3), modFallback(4)}read-createcurrent
zhoneVdslLineConfUpPsdMaskEnable
OBJECT-TYPE
This object selects the Psd Mask in the upstream direction. 'standard' : use the PSD Mask specified in the object zhoneVdslLineConfDownPsdSelect 'mod' : use the pre-defined Mask-On-Demand PSD Mask 'modFallback': use the pre-defined Mask-On-Demand PSD Mask with fallback
1.3.6.1.4.1.5504.5.13.1.1.11.1.110INTEGER {standard(2), mod(3), modFallback(4)}read-createcurrent
zhoneVdslLineConfDownPsdMaskSelect
OBJECT-TYPE
This object selects one of the standards based PSD mask for the downstream direction. The object zhoneVdslLineConfDownPsdMaskEnable must be set to 'standard' for this object to be active.
1.3.6.1.4.1.5504.5.13.1.1.11.1.111INTEGER {custom(1), customMOD(2), dmtPSDCOMSK2(3), dmtPSDFLATMSK(4), dmtPSDCABMSK2(5), dmtPSDCOMSK2RFI(6), dmtPSDFLATMSKRFI(7), dmtPSDCABMSK2RFI(8), dmtPSDADSL2NONOVLPM1(9), dmtPSDADSL2NONOVLPM2(10), dmtPSDADSL2NONOVLPFLAT(11), g993RegionC(12), g993RegionA(13), g993RegionA-E17a-D-32(14), g993RegionA-E17a-D-48(15), g993RegionA-E17a-D-64(16), g993RegionA-E17a-D-128(17), g998RegionB-M1x-A(18), g998RegionB-M1x-B(19), g998RegionB-M1x-NUS0(20), g998RegionB-M2x-A(21), g998RegionB-M2x-M(22), g998RegionB-M2x-B(23), g998RegionB-M2x-NUS0(24), g998RegionB-E17-M2x-NUS0(25), g998RegionB-E17-M2x-NUS0-M(26), g998RegionB-ADE17-M2x-NUS0-M(27), g998RegionB-ADE17-M2x-A(28), g998RegionB-ADE17-M2x-B(29), g998RegionB-E30-M2x-NUS0(30), g998RegionB-E30-M2x-NUS0-M(31), g998RegionB-ADE30-M2x-NUS0-M(32), g998RegionB-ADE30-M2x-NUS0-A(33), g998RegionB-NONSTD-E17-M2x(34), g998RegionB-NONSTD-E17-M2x-M(35), g997RegionB-M1c-A-7(36), g997RegionB-M1x-M-8(37), g997RegionB-M1x-M(38), g997RegionB-M2x-M-8(39), g997RegionB-M2x-A(40), g997RegionB-M2x-M(41), g997RegionB-HPE17-M1-NUS0(42), g997RegionB-HPE30-M1-NUS0(43), g997RegionB-E17-M2x-A(44), g997RegionB-E30-M2x-NUS0(45)}read-createcurrent
zhoneVdslLineConfUpPsdMaskSelect
OBJECT-TYPE
This object selects one of the standards based PSD mask for the upstream direction. The object zhoneVdslLineConfUpPsdMaskEnable must be set to 'standard' for this object to be active.
1.3.6.1.4.1.5504.5.13.1.1.11.1.112INTEGER {custom(1), g993J-ADLU-32(2), g993J-ADLU-36(3), g993J-ADLU-40(4), g993J-ADLU-44(5), g993J-ADLU-48(6), g993J-ADLU-52(7), g993J-ADLU-60(8), g993J-ADLU-64(9), g993JM-EU-32(10), g993JM-EU-36(11), g993JM-EU-40(12), g993JM-EU-44(13), g993JM-EU-48(14), g993JM-EU-52(15), g993JM-EU-60(16), g993JM-EU-64(17), dmtExtended(18), dmtJJ100(19), dmtStandard(20), g993RegionA-EU-32(21), g993RegionA-EU-36(22), g993RegionA-EU-40(23), g993RegionA-EU-44(24), g993RegionA-EU-48(25), g993RegionA-EU-52(26), g993RegionA-EU-56(27), g993RegionA-EU-60(28), g993RegionA-EU-64(29), g998RegionB-M1x-A(30), g998RegionB-M1x-B(31), g998RegionB-M1x-NUS0(32), g998RegionB-M2x-A(33), g998RegionB-M2x-M(34), g998RegionB-M2x-B(35), g998RegionB-M2x-NUS0(36), g998RegionB-E17-M2x-NUS0(37), g998RegionB-E17-M2x-NUS0-M(38), g998RegionB-ADE17-M2x-NUS0-M(39), g998RegionB-ADE17-M2x-A(40), g998RegionB-ADE17-M2x-B(41), g998RegionB-E30-M2x-NUS0(42), g998RegionB-E30-M2x-NUS0-M(43), g998RegionB-ADE30-M2x-NUS0-M(44), g998RegionB-ADE30-M2x-NUS0-A(45), g998RegionB-NONSTD-E17-M2x(46), g998RegionB-NONSTD-E17-M2x-M(47), g997RegionB-M1c-A-7(48), g997RegionB-M1x-M-8(49), g997RegionB-M1x-M(50), g997RegionB-M2x-M-8(51), g997RegionB-M2x-A(52), g997RegionB-M2x-M(53), g997RegionB-HPE17-M1-NUS0(54), g997RegionB-HPE30-M1-NUS0(55), g997RegionB-E17-M2x-A(56), g997RegionB-E30-M2x-NUS0(57)}read-createcurrent
zhoneVdslLineEnableTrellisCoding
OBJECT-TYPE
Enables/disables Trellis coding.
1.3.6.1.4.1.5504.5.13.1.1.11.1.113TruthValueread-createcurrent
zhoneVdslLineEnableRsCoding
OBJECT-TYPE
Enables/disables Rs coding.
1.3.6.1.4.1.5504.5.13.1.1.11.1.114TruthValueread-createcurrent
zhoneVdslLineConfPsdShape
OBJECT-TYPE
Maximum transmit PSD allowed on a VDSL2 line.
1.3.6.1.4.1.5504.5.13.1.1.11.1.115INTEGER {region-a-nus0(1), region-a-eu-32(2), region-a-eu-36(3), region-a-eu-40(4), region-a-eu-44(5), region-a-eu-48(6), region-a-eu-52(7), region-a-eu-56(8), region-a-eu-60(9), region-a-eu-64(10), region-a-eu-128(11), region-a-adlu-32(12), region-a-adlu-36(13), region-a-adlu-40(14), region-a-adlu-44(15), region-a-adlu-48(16), region-a-adlu-52(17), region-a-adlu-56(18), region-a-adlu-60(19), region-a-adlu-64(20), region-a-adlu-128(21), region-b-998-m1x-a(22), region-b-998-m1x-b(23), region-b-998-m1x-nus0(24), region-b-998-m2x-a(25), region-b-998-m2x-m(26), region-b-998-m2x-b(27), region-b-998-m2x-nus0(28), region-b-998-e17-m2x-nus0(29), region-b-998-e17-m2x-nus0-m(30), region-b-998-ade17-m2x-nus0-m(31), region-b-998-ade17-m2x-a(32), region-b-998-ade17-m2x-b(33), region-b-998-e30-m2x-nus0(34), region-b-998-e30-m2x-nus0-m(35), region-b-998-ade30-m2x-nus0-m(36), region-b-998-ade30-m2x-nus0-a(37), region-b-997-m1c-a-7(38), region-b-997-m1x-m-8(39), region-b-997-m1x-m(40), region-b-997-m2x-m-8(41), region-b-997-m2x-a(42), region-b-997-m2x-m(43), region-b-997-hpe17-m1-nus0(44), region-b-997-hpe30-m1-nus0(45), region-b-997-e17-m2x-a(46), region-b-997-e30-m2x-nus0(47), region-b-997-bt-anfp(48), region-c-138-b(49), region-c-276-b(50), region-c-138-co(51), region-c-276-co(52), region-c-tcmisdn(53), region-c-1104-co-17a(54), region-c-1104-co-30a(55)}read-createcurrent
zhoneVdslLineConfDownPhyRSupport
OBJECT-TYPE
Enable or disable downstream PHYR. Only supported by Broadcom PHYR ports.
1.3.6.1.4.1.5504.5.13.1.1.11.1.116INTEGER {enable(1), disable(2)}read-createcurrent
zhoneVdslLineConfUpPhyRSupport
OBJECT-TYPE
Enable or disable upstream PHYR. Only supported by Broadcom PHYR ports.
1.3.6.1.4.1.5504.5.13.1.1.11.1.117INTEGER {enable(1), disable(2)}read-createcurrent
zhoneVdslLineConfDownPhyRmaxINP
OBJECT-TYPE
PHYR maximum downstream impulse noise protection. A value of 0 specifies no protection. The values 5 through 160 specify the number of symbols in 1/10 increments. Only supported by Broadcom PHYR ports.
1.3.6.1.4.1.5504.5.13.1.1.11.1.118INTEGER (0 | 5..160)read-createcurrent
zhoneVdslLineConfUpPhyRmaxINP
OBJECT-TYPE
PHYR maximum upstream impulse noise protection. A value of 0 specifies no protection. The values 5 through 160 specify the number of symbols in 1/10 increments. Only supported by Broadcom PHYR ports.
1.3.6.1.4.1.5504.5.13.1.1.11.1.119INTEGER (0 | 5..160)read-createcurrent
zhoneVdslLineConfDownPhyRminRSoverhead
OBJECT-TYPE
PHYR minimum downstream RS overhead. Only supported by Broadcom PHYR ports.
1.3.6.1.4.1.5504.5.13.1.1.11.1.120INTEGER (0..255)read-createcurrent
zhoneVdslLineConfUpPhyRminRSoverhead
OBJECT-TYPE
PHYR minimum upstream RS overhead. Only supported by Broadcom PHYR ports.
1.3.6.1.4.1.5504.5.13.1.1.11.1.121INTEGER (0..255)read-createcurrent
zhoneVdslLineConfDownPhyRRtxRatio
OBJECT-TYPE
PHYR minimum downstream fraction of the line rate allocated for retransmission. Only supported by Broadcom PHYR ports.
1.3.6.1.4.1.5504.5.13.1.1.11.1.122INTEGER (0..255)read-createcurrent
zhoneVdslLineConfUpPhyRRtxRatio
OBJECT-TYPE
PHYR minimum upstream fraction of the line rate allocated for retransmission. Only supported by Broadcom PHYR ports.
1.3.6.1.4.1.5504.5.13.1.1.11.1.123INTEGER (0..255)read-createcurrent
zhoneVdslLineConfUpPboPsdParamA3
OBJECT-TYPE
Upstream power backoff PSD parameter A3. This parameter is only used if the mask selection is set to PSDMaskABParameters
1.3.6.1.4.1.5504.5.13.1.1.11.1.124Integer32 (4000..8096)read-createcurrent
zhoneVdslLineConfUpPboPsdParamA4
OBJECT-TYPE
Upstream power backoff PSD parameter A4. This parameter is only used if the mask selection is set to PSDMaskABParameters
1.3.6.1.4.1.5504.5.13.1.1.11.1.125Integer32 (4000..8096)read-createcurrent
zhoneVdslLineConfUpPboPsdParamB3
OBJECT-TYPE
Upstream power backoff PSD parameter B3. This parameter is only used if the mask selection is set to PSDMaskABParameters
1.3.6.1.4.1.5504.5.13.1.1.11.1.126Integer32 (0..4096)read-createcurrent
zhoneVdslLineConfUpPboPsdParamB4
OBJECT-TYPE
Upstream power backoff PSD parameter B4. This parameter is only used if the mask selection is set to PSDMaskABParameters
1.3.6.1.4.1.5504.5.13.1.1.11.1.127Integer32 (0..4096)read-createcurrent
zhoneVdslLineConfFallbackDefaultVpi
OBJECT-TYPE
ATM VPI to be used by the line when it trains in ADSL/ATM mode and bridges are configured for single-vc mode
1.3.6.1.4.1.5504.5.13.1.1.11.1.128Unsigned32 (0..255)read-createcurrent
zhoneVdslLineConfFallbackDefaultVci
OBJECT-TYPE
ATM VCI to be used by the line when it trains in ADSL/ATM mode and bridges are configured for single-vc mode
1.3.6.1.4.1.5504.5.13.1.1.11.1.129Unsigned32 (0..65535)read-createcurrent
zhoneVdslLineConfDownGinpSupport
OBJECT-TYPE
Enable or disable downstream G.INP / ITU-G.998.4. Only supported by Broadcom ports.
1.3.6.1.4.1.5504.5.13.1.1.11.1.130INTEGER {enable(1), disable(2)}read-createcurrent
zhoneVdslLineConfUpGinpSupport
OBJECT-TYPE
Enable or disable upstream G.INP / ITU-G.998.4. Only supported by Broadcom ports.
1.3.6.1.4.1.5504.5.13.1.1.11.1.131INTEGER {enable(1), disable(2)}read-createcurrent
zhoneVdslLineConfDownGinpEtrMax
OBJECT-TYPE
gInpEtrMax - Maximum allowed value for downstream expected throughput (ETR) in kbit/s. The valid values are all multiples of 8 from 0 to the maximum of the valid values of the maximum net data rate specified in the associated Recommendation. ITU-T G.998.4 7.1.1 Control parameters and 7.1.2 Valid configurations.
1.3.6.1.4.1.5504.5.13.1.1.11.1.132Unsigned32 (64..200000)read-createcurrent
zhoneVdslLineConfUpGinpEtrMax
OBJECT-TYPE
gInpEtrMax - Maximum allowed value for upstream expected throughput (ETR) in kbit/s. The valid values are all multiples of 8 from 0 to the maximum of the valid values of the maximum net data rate specified in the associated Recommendation. ITU-T G.998.4 7.1.1 Control parameters and 7.1.2 Valid configurations.
1.3.6.1.4.1.5504.5.13.1.1.11.1.133Unsigned32 (64..2000000)read-createcurrent
zhoneVdslLineConfDownGinpEtrMin
OBJECT-TYPE
gInpEtrMin - Minimum allowed value for downstream expected throughput (ETR) in kbit/s. The valid values are all multiples of 8 from 0 to the maximum of the valid values of the minimum net data rate specified in the associated Recommendation. ITU-T G.998.4 7.1.1 Control parameters and 7.1.2 Valid configurations.
1.3.6.1.4.1.5504.5.13.1.1.11.1.134Unsigned32 (64..200000)read-createcurrent
zhoneVdslLineConfUpGinpEtrMin
OBJECT-TYPE
gInpEtrMin - Minimum allowed value for upstream expected throughput (ETR) in kbit/s. The valid values are all multiples of 8 from 0 to the maximum of the valid values of the minimum net data rate specified in the associated Recommendation. ITU-T G.998.4 7.1.1 Control parameters and 7.1.2 Valid configurations.
1.3.6.1.4.1.5504.5.13.1.1.11.1.135Unsigned32 (64..200000)read-createcurrent
zhoneVdslLineConfDownGinpNdrMax
OBJECT-TYPE
gInpNdrMax - Maximum allowed value for downstream net data rate (NDR) in kbit/s. The valid values are all multiples of 8 from 0 to the maximum of the valid values of the maximum net data rate specified in the associated Recommendation. ITU-T G.998.4 7.1.1 Control parameters and 7.1.2 Valid configurations.
1.3.6.1.4.1.5504.5.13.1.1.11.1.136Unsigned32 (64..200000)read-createcurrent
zhoneVdslLineConfUpGinpNdrMax
OBJECT-TYPE
gInpNdrMax - Maximum allowed value for upstream net data rate (NDR) in kbit/s. The valid values are all multiples of 8 from 0 to the maximum of the valid values of the maximum net data rate specified in the associated Recommendation. ITU-T G.998.4 7.1.1 Control parameters and 7.1.2 Valid configurations.
1.3.6.1.4.1.5504.5.13.1.1.11.1.137Unsigned32 (64..200000)read-createcurrent
zhoneVdslLineConfDownGinpShineRatio
OBJECT-TYPE
gInpShineRatio - The downstream loss of rate in a 1 second interval expressed as a fraction of NDR due to a single high impulse noise event (SHINE) impulse noise environment expected by the operator to occur at a probability acceptable for the services. The valid values are all multiples of 0.001 from 0 to 0.1. This field uses 1 to equal 0.001 and 100 to equal 0.1. ITU-T G.998.4 7.1.1 Control parameters and 7.1.2 Valid configurations.
1.3.6.1.4.1.5504.5.13.1.1.11.1.138Unsigned32 (0..255)read-createcurrent
zhoneVdslLineConfUpGinpShineRatio
OBJECT-TYPE
gInpShineRatio - The upstream loss of rate in a 1 second interval expressed as a fraction of NDR due to a single high impulse noise event (SHINE) impulse noise environment expected by the operator to occur at a probability acceptable for the services. The valid values are all multiples of 0.001 from 0 to 0.1. This field uses 1 to equal 0.001 and 100 to equal 0.1. ITU-T G.998.4 7.1.1 Control parameters and 7.1.2 Valid configurations.
1.3.6.1.4.1.5504.5.13.1.1.11.1.139Unsigned32 (0..255)read-createcurrent
zhoneVdslLineConfDownGinpLeftrThreshold
OBJECT-TYPE
gInpLeftrThreshold - The downstream rate Threshold below which the Low Error Free Rate (LEFTR) defect is declared. The threshold used to declare leftr defects is expressed in fraction of the net data rate (NDR). The value 0 is a special value to indicate that the receiver shall use a special value for declaring leftr defect. The minimum valid threshold to declare leftr is ETR/2. The receiver shall ignore threshold values that are less than the minimum and shall use ETR/2 for declaring leftr defect instead. The valid values are all multiples of 0.01 from 0.01 to 0.99. This field uses 1 to equal 0.01 and 99 to equal 0.99.
1.3.6.1.4.1.5504.5.13.1.1.11.1.140Unsigned32 (0..99)read-createcurrent
zhoneVdslLineConfUpGinpLeftrThreshold
OBJECT-TYPE
gInpLeftrThreshold - The upstream rate Threshold below which the Low Error Free Rate (LEFTR) defect is declared. The threshold used to declare leftr defects is expressed in fraction of the net data rate (NDR). The value 0 is a special value to indicate that the receiver shall use a special value for declaring leftr defect. The minimum valid threshold to declare leftr is ETR/2. The receiver shall ignore threshold values that are less than the minimum and shall use ETR/2 for declaring leftr defect instead. The valid values are all multiples of 0.01 from 0.01 to 0.99. This field uses 1 to equal 0.01 and 99 to equal 0.99.
1.3.6.1.4.1.5504.5.13.1.1.11.1.141Unsigned32 (0..99)read-createcurrent
zhoneVdslLineConfDownGinpMaxDelay
OBJECT-TYPE
gInpMaxDelay - The maximum downstream delay in ms. This is the upper limit for the delay that is added to the transmission delay only caused by retransmissions. Here the receiver and/or the transmitter shall identify and discard all DTUs whose payload cannot be transferred over the reference point at the receiver without violating the delay_max limit. The time stamp shall be the criterion for discarding the DTUs. The processing delay between the U-interface and the retransmission sub-layer of the receiver in the retransmission data path direction shall be excluded from consideration for delay_max in the retransmission data path direction. The valid values are all integers from 1 to 63. ITU-T G.998.4 7.1.1 Control parameters, 7.1.2 Valid configurations, and 8.1.6 Time Stamp.
1.3.6.1.4.1.5504.5.13.1.1.11.1.142Unsigned32 (0..63)read-createcurrent
zhoneVdslLineConfUpGinpMaxDelay
OBJECT-TYPE
gInpMaxDelay - The maximum upstream delay in ms. This is the upper limit for the delay that is added to the transmission delay only caused by retransmissions. Here the receiver and/or the transmitter shall identify and discard all DTUs whose payload cannot be transferred over the reference point at the receiver without violating the delay_max limit. The time stamp shall be the criterion for discarding the DTUs. The processing delay between the U-interface and the retransmission sub-layer of the receiver in the retransmission data path direction shall be excluded from consideration for delay_max in the retransmission data path direction. The valid values are all integers from 1 to 63. ITU-T G.998.4 7.1.1 Control parameters, 7.1.2 Valid configurations, and 8.1.6 Time Stamp.
1.3.6.1.4.1.5504.5.13.1.1.11.1.143Unsigned32 (0..63)read-createcurrent
zhoneVdslLineConfDownGinpMinDelay
OBJECT-TYPE
gInpMinDelay - The minimum downstream delay in ms. This is the lower limit for the delay that is added to the transmission delay caused by retransmissions only. The time stamp shall be used by the outlet shaping function to determine when the payload of the DTU shall be sent to the reference point to meet the delay limits. The outlet shaping function shall minimize the additional delay that may be introduced above delay_ min , and shall never exceed delay_max. The valid values are all integers from 0 to 63. ITU-T G.998.4 7.1.1 Control parameters, 7.1.2 Valid configurations, and 8.1.6 Time Stamp.
1.3.6.1.4.1.5504.5.13.1.1.11.1.144Unsigned32 (0..63)read-createcurrent
zhoneVdslLineConfUpGinpMinDelay
OBJECT-TYPE
gInpMinDelay - The minimum upstream delay in ms. This is the lower limit for the delay that is added to the transmission delay caused by retransmissions only. The time stamp shall be used by the outlet shaping function to determine when the payload of the DTU shall be sent to the reference point to meet the delay limits. The outlet shaping function shall minimize the additional delay that may be introduced above delay_ min , and shall never exceed delay_max. The valid values are all integers from 0 to 63. ITU-T G.998.4 7.1.1 Control parameters, 7.1.2 Valid configurations, and 8.1.6 Time Stamp.
1.3.6.1.4.1.5504.5.13.1.1.11.1.145Unsigned32 (0..63)read-createcurrent
zhoneVdslLineConfDownGinpMin
OBJECT-TYPE
ginpMin - The minimum downstream impulse noise protection (INP) against single high impulse noise event (SHINE) in discrete multitone (DMT) symbols. The valid values are all integers from 0 to 63 for system with a sub-carrier spacing of 4.3125 kHz. The valid values are all integers from 0 to 127 for system with a sub-carrier spacing of 8.625 kHz. ITU-T G.998.4 7.1.1 Control parameters and 7.1.2 Valid configurations.
1.3.6.1.4.1.5504.5.13.1.1.11.1.146Unsigned32 (0..127)read-createcurrent
zhoneVdslLineConfUpGinpMin
OBJECT-TYPE
ginpMin - The minimum upstream impulse noise protection (INP) against single high impulse noise event (SHINE) in discrete multitone (DMT) symbols. The valid values are all integers from 0 to 63 for system with a sub-carrier spacing of 4.3125 kHz. The valid values are all integers from 0 to 127 for system with a sub-carrier spacing of 8.625 kHz. ITU-T G.998.4 7.1.1 Control parameters and 7.1.2 Valid configurations.
1.3.6.1.4.1.5504.5.13.1.1.11.1.147Unsigned32 (0..127)read-createcurrent
zhoneVdslLineConfDownGinpMinRSoverhead
OBJECT-TYPE
gInpMinRSoverhead - This value specifies the downstream bandwidth reserved for RS (reed-solomon) codewords. The minimum guaranteed R/N ratio. The unit is 1/256th and the range is 0..64 (0 to 25%).
1.3.6.1.4.1.5504.5.13.1.1.11.1.148Unsigned32 (0..64)read-createcurrent
zhoneVdslLineConfUpGinpMinRSoverhead
OBJECT-TYPE
gInpMinRSoverhead - This value specifies the upstream bandwidth reserved for RS (reed-solomon) codewords. The minimum guaranteed R/N ratio. The unit is 1/256th and the range is 0..64 (0 to 25%).
1.3.6.1.4.1.5504.5.13.1.1.11.1.149Unsigned32 (0..64)read-createcurrent
zhoneVdslLineConfDownGinpReinCfg
OBJECT-TYPE
gInpReinCfg - The minimum downstream impulse protection against electrical repetitive impulse noise (REIN) in DMT symbols. The valid values are all integers from 0 to 7 for system with a sub-carrier spacing of 4.3125 kHz. The valid values are all integers from 0 to 13 for system with a sub-carrier spacing of 8.625 kHz. ITU-T G.998.4 7.1.1 Control parameters and 7.1.2 Valid configurations.
1.3.6.1.4.1.5504.5.13.1.1.11.1.150Unsigned32 (0..7)read-createcurrent
zhoneVdslLineConfUpGinpReinCfg
OBJECT-TYPE
gInpReinCfg - The minimum upstream impulse protection against electrical repetitive impulse noise (REIN) in DMT symbols. The valid values are all integers from 0 to 7 for system with a sub-carrier spacing of 4.3125 kHz. The valid values are all integers from 0 to 13 for system with a sub-carrier spacing of 8.625 kHz. ITU-T G.998.4 7.1.1 Control parameters and 7.1.2 Valid configurations.
1.3.6.1.4.1.5504.5.13.1.1.11.1.151Unsigned32 (0..7)read-createcurrent
zhoneVdslLineConfDownGinpReinFreq
OBJECT-TYPE
ginpReinFreq specifies the frequency of REIN inter-arrival time. It is used in the Channel Initialization Policy and on-line reconfiguration procedures. REIN is commonly coupled from electrical power cables appliances drawing power from the AC electrical power network, having a repetition rate of twice the AC power frequency (100 or 120 Hz). The valid values are integers 100 hz or 120 hz. ITU-T G.998.4 7.1.1 Control parameters and 7.1.2 Valid configurations.
1.3.6.1.4.1.5504.5.13.1.1.11.1.152INTEGER {freq100hz(1), freq120hz(2)}read-writecurrent
zhoneVdslLineConfUpGinpReinFreq
OBJECT-TYPE
ginpReinFreq specifies the frequency of REIN inter-arrival time. It is used in the Channel Initialization Policy and on-line reconfiguration procedures. REIN is commonly coupled from electrical power cables appliances drawing power from the AC electrical power network, having a repetition rate of twice the AC power frequency (100 or 120 Hz). The valid values are integers 100 hz or 120 hz. ITU-T G.998.4 7.1.1 Control parameters and 7.1.2 Valid configurations.
1.3.6.1.4.1.5504.5.13.1.1.11.1.153INTEGER {freq100hz(1), freq120hz(2)}read-writecurrent
zhoneVdslLineConfDownGinpRtxMode
OBJECT-TYPE
gInpRtxMode - Downstream retransmission Mode (RTX MODE). The RTX_MODE is a configuration parameter used to control activation of retransmission during initialization. This parameter has 4 valid values: FORBIDDEN: ITU-T G.998.4 retransmission not allowed. PREFERRED: ITU-T G.998.4 retransmission is preferred by the operator. (i.e., if ITU-T G.998.4 RTX capability is supported by both XTU's, the XTU's shall select ITU-T G.998.4 operation for this direction). FORCED: Force the use of the ITU-T G.998.4 retransmission. (i.e., if ITU-T G.998.4 RTX capability in this direction is not supported by both XTU's or not selected by the XTU's, an initialization failure shall result). NOTE: Due to the optionality of ITU-T G.998.4 retransmission in upstream direction, the use of FORCED in upstream may lead to initialization failure, even if the XTU is supporting ITU-T G.998.4 (in downstream). TESTMODE: Force the use of the ITU-T G.998.4 retransmission in the test mode described in clause 10.4. (i.e., if ITU-T G.998.4 RTX capability is not supported by both XTU's or not selected by the XTU's, an initialization failure shall result). ITU-T G.998.4 11.1.13 Retransmission Mode (RTX_MODE)
1.3.6.1.4.1.5504.5.13.1.1.11.1.154INTEGER {forbidden(1), preferred(2), forced(3), testmode(4)}read-createcurrent
zhoneVdslLineConfUpGinpRtxMode
OBJECT-TYPE
gInpRtxMode - Upstream retransmission Mode (RTX MODE). The RTX_MODE is a configuration parameter used to control activation of retransmission during initialization. This parameter has 4 valid values: FORBIDDEN: ITU-T G.998.4 retransmission not allowed. PREFERRED: ITU-T G.998.4 retransmission is preferred by the operator. (i.e., if ITU-T G.998.4 RTX capability is supported by both XTU's, the XTU's shall select ITU-T G.998.4 operation for this direction). FORCED: Force the use of the ITU-T G.998.4 retransmission. (i.e., if ITU-T G.998.4 RTX capability in this direction is not supported by both XTU's or not selected by the XTU's, an initialization failure shall result). NOTE: Due to the optionality of ITU-T G.998.4 retransmission in upstream direction, the use of FORCED in upstream may lead to initialization failure, even if the XTU is supporting ITU-T G.998.4 (in downstream). TESTMODE: Force the use of the ITU-T G.998.4 retransmission in the test mode described in clause 10.4. (i.e., if ITU-T G.998.4 RTX capability is not supported by both XTU's or not selected by the XTU's, an initialization failure shall result). ITU-T G.998.4 11.1.13 Retransmission Mode (RTX_MODE)
1.3.6.1.4.1.5504.5.13.1.1.11.1.155INTEGER {forbidden(1), preferred(2), forced(3), testmode(4)}read-createcurrent
zhoneVdslLineAlarmConfProfileTable
OBJECT-TYPE
This table contains information on the VDSL line alarm configuration. One entry in this table reflects a profile defined by a manager which can be used to configure the VDSL line alarm thresholds. Entries in this table MUST be maintained in a persistent manner.
1.3.6.1.4.1.5504.5.13.1.1.20not-accessiblecurrent
zhoneVdslLineAlarmConfProfileEntry
OBJECT-TYPE
Each entry consists of a list of parameters that represents the configuration of a VDSL line alarm profile. A default profile with an index of 'DEFVAL', will always exist and its parameters will be set to vendor specific values, unless otherwise specified in this document.
1.3.6.1.4.1.5504.5.13.1.1.20.1not-accessiblecurrent
zhoneVdslLineAlarmConfProfileName
OBJECT-TYPE
The name for this profile as specified by an administrator.
1.3.6.1.4.1.5504.5.13.1.1.20.1.1SnmpAdminString (SIZE(1..32))not-accessiblecurrent
zhoneVdslLineAlarmConfThresh15MinLofs
OBJECT-TYPE
This object configures the threshold for the number of loss of frame seconds (LOFs) within any given 15-minute performance data collection interval. If the value of loss of frame seconds in a particular 15-minute collection interval reaches/exceeds this value, a zhoneVdslPerfLofsThreshNotification notification will be generated. No more than one notification will be sent per interval.
1.3.6.1.4.1.5504.5.13.1.1.20.1.2INTEGER (0..900)read-createcurrent
zhoneVdslLineAlarmConfThresh15MinLoss
OBJECT-TYPE
This object configures the threshold for the number of loss of signal seconds (LOSs) within any given 15-minute performance data collection interval. If the value of loss of signal seconds in a particular 15-minute collection interval reaches/exceeds this value, a zhoneVdslPerfLossThreshNotification notification will be generated. One notification will be sent per interval per endpoint.
1.3.6.1.4.1.5504.5.13.1.1.20.1.3INTEGER (0..900)read-createcurrent
zhoneVdslLineAlarmConfThresh15MinLprs
OBJECT-TYPE
This object configures the threshold for the number of loss of power seconds (LPRs) within any given 15-minute performance data collection interval. If the value of loss of power seconds in a particular 15-minute collection interval reaches/exceeds this value, a zhoneVdslPerfLprsThreshNotification notification will be generated. No more than one notification will be sent per interval.
1.3.6.1.4.1.5504.5.13.1.1.20.1.4INTEGER (0..900)read-createcurrent
zhoneVdslLineAlarmConfThresh15MinLols
OBJECT-TYPE
This object configures the threshold for the number of loss of link seconds (LOLs) within any given 15-minute performance data collection interval. If the value of loss of link seconds in a particular 15-minute collection interval reaches/exceeds this value, a zhoneVdslPerfLolsThreshNotification notification will be generated. No more than one notification will be sent per interval.
1.3.6.1.4.1.5504.5.13.1.1.20.1.5INTEGER (0..900)read-createcurrent
zhoneVdslLineAlarmConfThresh15MinESs
OBJECT-TYPE
This object configures the threshold for the number of errored seconds (ESs) within any given 15-minute performance data collection interval. If the value of errored seconds in a particular 15-minute collection interval reaches/exceeds this value, a zhoneVdslPerfEssThreshNotification notification will be generated. No more than one notification will be sent per interval.
1.3.6.1.4.1.5504.5.13.1.1.20.1.6INTEGER (0..900)read-createcurrent
zhoneVdslLineAlarmConfThresh15MinSESs
OBJECT-TYPE
This object configures the threshold for the number of severely errored seconds (SESs) within any given 15-minute performance data collection interval. If the value of severely errored seconds in a particular 15-minute collection interval reaches/exceeds this value, a zhoneVdslPerfSessThreshNotification notification will be generated. No more than one notification will be sent per interval.
1.3.6.1.4.1.5504.5.13.1.1.20.1.7INTEGER (0..900)read-createcurrent
zhoneVdslLineAlarmConfThresh15MinUASs
OBJECT-TYPE
This object configures the threshold for the number of unavailable seconds (UASs) within any given 15-minute performance data collection interval. If the value of unavailable seconds in a particular 15-minute collection interval reaches/exceeds this value, a zhoneVdslPerfUassThreshNotification notification will be generated. No more than one notification will be sent per interval.
1.3.6.1.4.1.5504.5.13.1.1.20.1.8INTEGER (0..900)read-createcurrent
zhoneVdslLineAlarmConfInitFailure
OBJECT-TYPE
This object specifies if a vdslInitFailureNotification notification will be generated if an initialization failure occurs.
1.3.6.1.4.1.5504.5.13.1.1.20.1.9TruthValueread-createcurrent
zhoneVdslLineAlarmConfProfRowStatus
OBJECT-TYPE
This object is used to create a new row or modify or delete an existing row in this table. A profile activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service, (by setting this object to 'destroy' or 'outOfService') it must be first unreferenced from all associated lines. An 'active' profile may be modified at any time.
1.3.6.1.4.1.5504.5.13.1.1.20.1.10RowStatusread-createcurrent
zhoneVdslLineAlarmConfThresh1DayLofs
OBJECT-TYPE
This object configures the threshold for the number of loss of frame seconds (LOFs) within any given 1-day performance data collection interval. If the value of loss of frame seconds in a particular 1-day collection interval reaches/exceeds this value, a zhoneVdslPerfLofsThreshNotification notification will be generated. No more than one notification will be sent per interval
1.3.6.1.4.1.5504.5.13.1.1.20.1.11INTEGER (0..86400)read-createcurrent
zhoneVdslLineAlarmConfThresh1DayLoss
OBJECT-TYPE
This object configures the threshold for the number of loss of signal seconds (LOSs) within any given 1-day performance data collection interval. If the value of loss of signal seconds in a particular 1-day collection interval reaches/exceeds this value, a zhoneVdslPerfLossThreshNotification notification will be generated. No more than one notification will be sent per interval
1.3.6.1.4.1.5504.5.13.1.1.20.1.12INTEGER (0..86400)read-createcurrent
zhoneVdslLineAlarmConfThresh1DayLprs
OBJECT-TYPE
This object configures the threshold for the number of loss of power seconds (LPRs) within any given 1-day performance data collection interval. If the value of loss of power seconds in a particular 1-day collection interval reaches/exceeds this value, a zhoneVdslPerfLprsThreshNotification notification will be generated. No more than one notification will be sent per interval
1.3.6.1.4.1.5504.5.13.1.1.20.1.13INTEGER (0..86400)read-createcurrent
zhoneVdslLineAlarmConfThresh1DayLols
OBJECT-TYPE
This object configures the threshold for the number of loss of link seconds (LOLs) within any given 1-day performance data collection interval. If the value of loss of link seconds in a particular 1-day collection interval reaches/exceeds this value, a zhoneVdslPerfLolsThreshNotification notification will be generated. No more than one notification will be sent per interval
1.3.6.1.4.1.5504.5.13.1.1.20.1.14INTEGER (0..86400)read-createcurrent
zhoneVdslLineAlarmConfThresh1DayESs
OBJECT-TYPE
This object configures the threshold for the number of errored seconds (ESs) within any given 1-day performance data collection interval. If the value of errored seconds in a particular 1-day collection interval reaches/exceeds this value, a zhoneVdslPerfEssThreshNotification notification will be generated. No more than one notification will be sent per interval
1.3.6.1.4.1.5504.5.13.1.1.20.1.15INTEGER (0..86400)read-createcurrent
zhoneVdslLineAlarmConfThresh1DaySESs
OBJECT-TYPE
This object configures the threshold for the number of severely errored seconds (SESs) within any given 1-day performance data collection interval. If the value of severely errored seconds in a particular 1-day collection interval reaches/exceeds this value, a zhoneVdslPerfSessThreshNotification notification will be generated. No more than one notification will be sent per interval
1.3.6.1.4.1.5504.5.13.1.1.20.1.16INTEGER (0..86400)read-createcurrent
zhoneVdslLineAlarmConfThresh1DayUASs
OBJECT-TYPE
This object configures the threshold for the number of unavailable seconds (UASs) within any given 1-day performance data collection interval. If the value of unavailable seconds in a particular 1-day collection interval reaches/exceeds this value, a zhoneVdslPerfUasThreshNotification notification will be generated. No more than one notification will be sent per interval
1.3.6.1.4.1.5504.5.13.1.1.20.1.17INTEGER (0..86400)read-createcurrent
zhoneVdslLineAlarmConfThresh1DayInitFailure
OBJECT-TYPE
This object specifies if a vdslThresh1DayInitFailureNotification notification will be generated if an initialization failure occurs.
1.3.6.1.4.1.5504.5.13.1.1.20.1.18TruthValueread-createcurrent
zhoneVdslCustomNotchConfProfileTable
OBJECT-TYPE
This table contains HAM (Handheld Amateur Radio) custom notch information.
1.3.6.1.4.1.5504.5.13.1.1.21not-accessiblecurrent
zhoneVdslCustomNotchConfProfileEntry
OBJECT-TYPE
Each VDSL port can have custom notches.
1.3.6.1.4.1.5504.5.13.1.1.21.1not-accessiblecurrent
zhoneVdslCustomNotchConfId
OBJECT-TYPE
Each VDSL2 port can have eight (8) custom notch pairs.
1.3.6.1.4.1.5504.5.13.1.1.21.1.1Unsigned32 (1..8)read-createcurrent
zhoneVdslCustomNotchConfStart
OBJECT-TYPE
Specifies the start frequency of custom HAM (Handheld Amateur Radio) notch. zhoneVdslCustomNotchConfStart MUST be less than or equal to zhoneVdslCustomNotchConfStop.
1.3.6.1.4.1.5504.5.13.1.1.21.1.2Unsigned32 (0..200000)read-createcurrent
zhoneVdslCustomNotchConfStop
OBJECT-TYPE
Specifies the end frequency of custom HAM (Handheld Amateur Radio) notch. zhoneVdslCustomNotchConfStop MUST be greater than or equal to zhoneVdslCustomNotchConfStart.
1.3.6.1.4.1.5504.5.13.1.1.21.1.3Unsigned32 (0..200000)read-createcurrent
zhoneVdslVectDataTable
OBJECT-TYPE
Used to retrieve the vectoring packet counts.
1.3.6.1.4.1.5504.5.13.1.1.22not-accessiblecurrent
zhoneVdslVectDataEntry
OBJECT-TYPE
Vectoring Packet statistics data
1.3.6.1.4.1.5504.5.13.1.1.22.1not-accessiblecurrent
zhoneVdslVectDataEsDsCounter
OBJECT-TYPE
Error Sample Downstream Packet Counter
1.3.6.1.4.1.5504.5.13.1.1.22.1.1Integer32read-onlycurrent
zhoneVdslVectDataEsUsCounter
OBJECT-TYPE
Error Sample Upstream Packet Counter
1.3.6.1.4.1.5504.5.13.1.1.22.1.2Integer32read-onlycurrent
zhoneVdslVectDataIsDsFeValid
OBJECT-TYPE
Is Downstream Fe Valid
1.3.6.1.4.1.5504.5.13.1.1.22.1.3Integer32read-onlycurrent
zhoneVdslVectDataEsFeDsCounter
OBJECT-TYPE
Error Sample Fe Downstream Counter
1.3.6.1.4.1.5504.5.13.1.1.22.1.4Integer32read-onlycurrent
zhoneVdslConformance
OBJECT-IDENTITY
1.3.6.1.4.1.5504.5.13.1.3
zhoneVdslGroups
OBJECT-IDENTITY
1.3.6.1.4.1.5504.5.13.1.3.1
zhoneVdslCompliances
OBJECT-IDENTITY
1.3.6.1.4.1.5504.5.13.1.3.2

Notifications

NameOIDStatus
vdslXtucPerf15MinLofsThreshTrap
NOTIFICATION-TYPE
Loss of Framing 15-minute interval threshold (vdslLineAlarmConfThresh15MinLofs) reached.
1.3.6.1.4.1.5504.5.13.1.0.1current
vdslXtucPerf15MinLossThreshTrap
NOTIFICATION-TYPE
Loss of Signal 15-minute interval threshold (vdslLineAlarmConfThresh15MinLoss) reached.
1.3.6.1.4.1.5504.5.13.1.0.2current
vdslXtucPerf15MinLprsThreshTrap
NOTIFICATION-TYPE
Loss of Power 15-minute interval threshold (vdslLineAlarmConfThresh15MinLprs) reached.
1.3.6.1.4.1.5504.5.13.1.0.3current
vdslXtucPerf15MinLolsThreshTrap
NOTIFICATION-TYPE
Loss of Link 15-minute interval threshold (vdslLineAlarmConfThresh15MinLols) reached.
1.3.6.1.4.1.5504.5.13.1.0.4current
vdslXtucPerf15MinESsThreshTrap
NOTIFICATION-TYPE
Errored Seconds 15-minute interval threshold (vdslLineAlarmConfThresh15MinESs) reached.
1.3.6.1.4.1.5504.5.13.1.0.5current
vdslXtucPerf15MinSESsThreshTrap
NOTIFICATION-TYPE
Severely Errored Seconds 15-minute interval threshold (vdslLineAlarmConfThresh15MinSESs) reached.
1.3.6.1.4.1.5504.5.13.1.0.6current
vdslXtucPerf15MinUASsThreshTrap
NOTIFICATION-TYPE
Unavailable Seconds 15-minute interval threshold (vdslLineAlarmConfThresh15MinUASs) reached.
1.3.6.1.4.1.5504.5.13.1.0.7current
vdslXtucPerf1DayLofsThreshTrap
NOTIFICATION-TYPE
Loss of Framing 1-day interval threshold (vdslLineAlarmConfThresh1DayLofs) reached.
1.3.6.1.4.1.5504.5.13.1.0.8current
vdslXtucPerf1DayLossThreshTrap
NOTIFICATION-TYPE
Loss of Signal 1-day interval threshold (vdslLineAlarmConfThresh1DayLoss) reached.
1.3.6.1.4.1.5504.5.13.1.0.9current
vdslXtucPerf1DayLprsThreshTrap
NOTIFICATION-TYPE
Loss of Power 1-day interval threshold (vdslLineAlarmConfThresh1DayLprs) reached.
1.3.6.1.4.1.5504.5.13.1.0.10current
vdslXtucPerf1DayLolsThreshTrap
NOTIFICATION-TYPE
Loss of Link 1-day interval threshold (vdslLineAlarmConfThresh1DayLols) reached.
1.3.6.1.4.1.5504.5.13.1.0.11current
vdslXtucPerf1DayESsThreshTrap
NOTIFICATION-TYPE
Errored Seconds 1-day interval threshold (vdslLineAlarmConfThresh1DayESs) reached.
1.3.6.1.4.1.5504.5.13.1.0.12current
vdslXtucPerf1DaySESsThreshTrap
NOTIFICATION-TYPE
Severely Errored Seconds 1-day interval threshold (vdslLineAlarmConfThresh1DaySESs) reached.
1.3.6.1.4.1.5504.5.13.1.0.13current
vdslXtucPerf1DayUASsThreshTrap
NOTIFICATION-TYPE
Unavailable Seconds 1-day interval threshold (vdslLineAlarmConfThresh1DayUASs) reached.
1.3.6.1.4.1.5504.5.13.1.0.14current
zhoneVdslInitFailureTrap
NOTIFICATION-TYPE
Vtu initialization failed.
1.3.6.1.4.1.5504.5.13.1.0.15current
vdslXtucMinTxThresholdAlarmFailureTrap
NOTIFICATION-TYPE
This trap is thrown when the XTUC line rate syncs below the threshold rate as defined by zhoneVdslLineConfDownMinTxThresholdAlarm.
1.3.6.1.4.1.5504.5.13.1.0.16current
vdslXturMinTxThresholdAlarmFailureTrap
NOTIFICATION-TYPE
This trap is thrown when the XTUR line rate syncs below the threshold rate as defined by zhoneVdslLineConfUpMinTxThresholdAlarm.
1.3.6.1.4.1.5504.5.13.1.0.17current

Conformance

NameOIDStatus
zhoneVdslGroup
OBJECT-GROUP
A collection of objects providing information about a VDSL Line.
1.3.6.1.4.1.5504.5.13.1.3.1.1current
zhoneVdslNotificationGroup
NOTIFICATION-GROUP
This group supports notifications of significant conditions associated with VDSL Lines.
1.3.6.1.4.1.5504.5.13.1.3.1.2current
zhoneVdslLineMibCompliance
MODULE-COMPLIANCE
The compliance statement for SNMP entities which manage VDSL interfaces.
1.3.6.1.4.1.5504.5.13.1.3.2.1current