ZHONE-COM-BRIDGE-REC-MIB

TEXTUAL-CONVENTION

state as shown in 'bridge show'.

TEXTUAL-CONVENTION

EAPS State Values (per RFC 3619bis). IDLE = 0x00 (EAPS Domain (Master/Transit) still not running) COMPLETE = 0x01 (Master in complete State) FAILED = 0x02 (Master in Failed State) LINKS-UP = 0x03 (Transit in links-up State. Both ring-ports are up) LINK-DOWN = 0x04 (Transit in Link-Down State. One or both ring-ports are down) PREFORWARDING = 0x05 (Transit in Preforwarding State) INIT = 0x06 (Master in Init State)

type

TEXTUAL-CONVENTION

Description.

OBJECT-TYPE

This table contains information required for the management of bridge interfaces.

OBJECT-TYPE

An entry exists for each bridge interface in the system. At a mininum the ifIndex must be present to create a row.

OBJECT-TYPE

If this bridge interface is on an ATM VC, the ATM VPI is specified here. If the bridge interface is not an ATM VC, this field is ignored. The VPI value for a VPL or VCL. The value VPI=0 is only allowed for a VCL. For ATM UNIs supporting VPCs the VPI value ranges from 0 to 255. The VPI value 0 is supported for ATM UNIs conforming to the ATM Forum UNI 4.0 Annex 8 (Virtual UNIs) specification. For ATM UNIs supporting VCCs the VPI value ranges from 0 to 255. For ATM NNIs the VPI value ranges from 0 to 4095. The maximum VPI value cannot exceed the value allowable by atmInterfaceMaxVpiBits defined in ATM-MIB.

OBJECT-TYPE

If this bridge interface is on an ATM VC, the ATM VCI is specified here. The range is 32...65535. The maximum VCI value cannot exceed the value allowable by atmInterfaceMaxVciBits defined in ATM-MIB. If the bridge interface is not an ATM VC, but for example an ethernet interface, this field should be set to 0.

OBJECT-TYPE

The Virtual LAN Id for VLAN Tag Insertion.

OBJECT-TYPE

If true, enable VLAN Tagging.

OBJECT-TYPE

If true, send ARP requests selectively or by flood.

OBJECT-TYPE

If true, discard non-ARP broadcast packets.

OBJECT-TYPE

If true, snoop unicast packets to build ARP table.

OBJECT-TYPE

If true, snoop unicast packets to build MAC paths.

OBJECT-TYPE

Maximum number of unicast addresses for I/F.

OBJECT-TYPE

If true, snoop multicast packets for IGMP joins/leaves.

OBJECT-TYPE

If true, attempt to forward via unicast MAC paths.

OBJECT-TYPE

If true, attempt to forward via multicast MAC paths.

OBJECT-TYPE

If true, attempt to forward via VLAN default paths.

OBJECT-TYPE

An entry exists for each bridge interface in the system. Only Ifindex and lower if index is needed to create a row.

OBJECT-TYPE

This object is used to create and remove rows in the table. See bridgeInterfaceEntry description for minimum requirements.

OBJECT-TYPE

If TRUE, forwards broadcast DHCPOFFER or DHCPACK packets even if bridgeFilterBroadcast is TRUE for that interface.

OBJECT-TYPE

Index used as partial address of a group of entries in the packetRuleTable, each of which prescribes a filtering condition for the ingress interface.

OBJECT-TYPE

The Class-Of-Service (COS) value used for VLAN Tag Insertion.

OBJECT-TYPE

Determines COS setting on packets bridged out this interface. disable - COS setting is untouched. all - COS will be set to bridgeIfOutgoingCOSValue.

OBJECT-TYPE

The COS value loaded into outgoing tagged packets. Applicable only if interface sends tagged packets and bridgeIfOutgoingCOSOption is outgoingCOSOption_all.

OBJECT-TYPE

The value of the tag protocol identifier that is being used for QinQ packets. (0x8100 is default.)

OBJECT-TYPE

The s-tag value that we are expecting to put on packets that are Rxed on this interface.

OBJECT-TYPE

If true, enable S-tag tagging on this IF.

OBJECT-TYPE

Determines s-tag COS settings on packets bridged out this interface: disable - s-tag COS setting just passed as Rxed. all - s-tag COS will be set with s_tagOutgoingCOSValue.

OBJECT-TYPE

The s-tag COS to be used when doing s-tag insertion.

OBJECT-TYPE

The s-tag COS value loaded into outgoing tagged packets. Applicaple only if interface sends S-tagged packets and s_tagOutgoingCOSOption is All.

OBJECT-TYPE

List of mcast-control-ids this bridge-interface-record is associated with. It is an integer stored as string, and controls which channels a user can watch. Note: unlike for IP, an empty list here allows user to watch all channels.

OBJECT-TYPE

Maximum number of multicast (video) streams that we will support.

OBJECT-TYPE

If true, this interface accepts PPPoA packets and will bridge them out as PPPoE packets.

OBJECT-TYPE

If true, flood frames with unknown unicast MAC address that would otherwise be discarded.

OBJECT-TYPE

If true, flood all multicast traffic received on this bridge to all other ports on this vlan.

OBJECT-TYPE

Index used as partial address of a group of entries in the packetRuleTable, each of which prescribes a filtering condition for the egress interface.

OBJECT-TYPE

none : Dynamic IP Filtering on bridge based on DHCP, is disabled. BIT 1(mac) : MAC address based Filtering based on DHCP, is enabled. BIT 2(ip) : IP address based dynamic IP Filtering based on DHCP, is enabled. Defval is changed to correct the Zhone script errors.

OBJECT-TYPE

none :IP address and Mac address are not learned from DHCP packets. BIT 1 (mac): MAC addresses are learned from DHCP packets. ip 2 (ip) : IP addresses are learned from DHCP packets. The Defval is changed to correct the Zhone script errors.

OBJECT-TYPE

If true, the on-demand stats collection for this bridge interface will be enabled and packets will be counted. If bytes, the on-demand stats collection for this bridge interface will be enabled and abd bytes will be counted.

OBJECT-TYPE

The Multicast Vlan Registration (MVR) vlan ID. Multicast video packets with this vlan can be vlan translated out this bridge.

OBJECT-TYPE

If a packet's VLAN ID value matches this object's value then the packet's VLAN ID will be translated to the value of bridgeIfVlanId. A zero value disables translation.

OBJECT-TYPE

If a packet's SLAN ID value matches this object's value then the packet's SLAN ID will be translated to the value of bridgeIfStagId. A zero value disables translation.

OBJECT-TYPE

Values: up(1), UP down(2), DWN trouble(3), TRB notAvailable(4), NA initializing(5), INI adminDown(6), ADN adminStateTest(7), TST adminStateNone(8), N/S ready(9), RDY discovering(10), DSC unknown(11), ??? blocked(12), BLK pending(13), PND disabled(14), DIS learning(15), LRN forwarding(16), FWD blockedFlapping(17), BLF blockedPersistent(18), BLP blockedFlappingPersistenr(19), BFP

OBJECT-TYPE

Set to TRUE to unblock a bridge that is blocked due to flapping.

OBJECT-TYPE

bridge type

OBJECT-TYPE

GPON GEM Port ID used only to create a bridge on a GPON ONU.

OBJECT-TYPE

GPON Traffic Profile Index used only to create a bridge on a GPON ONU.

OBJECT-TYPE

Determines COS settings on incoming packets bridged out this interface: disable - COS replcement feature is disabled all - COS will be set with vlanIDCOS.

OBJECT-TYPE

Determines s-tag COS settings on incoming packets bridged out this interface: disable - s-tag COS setting just passed as Rxed. all - s-tag COS will be set with s-tagIdCOS.

OBJECT-TYPE

A collection of staticBridgeEntries.

OBJECT-TYPE

Static Bridge entries are created by the user in order to specify forwarding for a particular interface, vlanId, mac address or ip address, slanId (for QinQ). The INDEX value for staticBridgeEntry consists of following 5 values: ifIndex staticBridgeAddressType bridgeIfVlanId staticBridgeMacOrIpAddress bridgeIfStagId If staticBridgeAddressType is set to macAddr(1), then staticBridgeMacOrIpAddress represents a MAC Address, and ifIndex, bridgeIfVlanId and staticBridgeMacOrIpAddress are used for the bridge path. If staticBridgeAddressType is set to ipAddr(2), then staticBridgeMacOrIpAddress represents an IP Address, and ifIndex, bridgeIfVlanId and staticBridgeMacOrIpAddress are used for the bridge path. If staticBridgeAddressType is set to vlanIdAddr(3), then ifIndex and bridgeIfVlanId are used for the bridge path. If staticBridgeAddressType is set to globalAddr(4), then ifIndex is used for the bridge path.

OBJECT-TYPE

If the staticBridgeAddressType is set to macAddr(1), then this field represents a MAC address. If the staticBridgeAddressType is set to ipAddr(2), then this field represents an IP address.

OBJECT-TYPE

If staticBridgeAddressType is set to macAddr(1), then staticBridgeMacOrIpAddress represents a MAC Address, and ifIndex, bridgeIfVlanId and staticBridgeMacOrIpAddress are used for the bridge path. If staticBridgeAddressType is set to ipAddr(2), then staticBridgeMacOrIpAddress represents an IP Address, and ifIndex, bridgeIfVlanId and staticBridgeMacOrIpAddress are used for the bridge path. If staticBridgeAddressType is set to vlanIdAddr(3) or intralinkAddr(7), then ifIndex and bridgeIfVlanId are used for the bridge path. If staticBridgeAddressType is set to globalAddr(4), globalIntralinkAddr(8), or mvrAddr(13) then ifIndex is used for the bridge path. If staticBridgeAddressType is set to dhcpAllowOui( 720901) then the first 3 bytes of the MAC address contains the OUI that we will allow DHCP addresses to be granted to, global scope. If staticBridgeAddressType is set to dhcpIpAddr(9), or to dhcpMacAddr(10), then the other fields are populated as for address types ipAddr and macAddr respectively, with the difference that these are secure entries, learned by snooping DHCP. If staticBridgeAddressType is set to vlanParms(14), then the static bridge entry holds parameters for the given VLAN and SLAN ID (for example, flap mode, unicast aging period, etc) and is not associated with any specific bridge, but with all bridges with the same VLAN/SLAN ID. For this reason, the IfIndex of this entry must be zero. If staticBridgeAddressType is set to secMvrAddr(15), then the static bridge entry holds parameters for a Secondary MVR path. The VLAN ID of this entry is the Secondary VLAN ID.

OBJECT-TYPE

Multicast Aging period in tenths of seconds for the specified VLAN. After the specified aging period is met, the VLAN address is deleted from the routing table. A value of 0 indicates that aging is turned off. Maximum value is 2147483647 tenths of seconds, which equates to approximately 2485.51 days.

OBJECT-TYPE

Used to create, modify or delete an entry in this table.

OBJECT-TYPE

This object enables or disable Flap Control in the Bridge Filter Table. The value 'disable(2)' turns Flap Control mode off. The values 'enable(3)' or 'fast(4) turn flap control mode on. 'Enable(3)' applies a hold time of 60 secs before allowing addr/IP to be moved to a new port, while 'fast(4)' applies a hold time of 0 secs. A value of 'default(1)' indicates 'Don't Care' and defaults to a disable or enable set by another entry.

OBJECT-TYPE

Multicast Aging period in tenths of seconds for the specified VLAN. After the specified aging period is met, the VLAN address is deleted from the routing table. A value of 0 indicates that aging is turned off. Maximum value is 2147483647 tenths of seconds, which equates to approximately 2485.51 days.

OBJECT-TYPE

How often (in seconds) we as a bridge inject IGMP query values into the stream.

OBJECT-TYPE

none : IGMP Snooping with Proxy reporting is disabled. BIT 0(igmpProcessJoinAndLeave) : igmpProcessJoinandLeave is enabled for IGMP packets. BIT 1(igmpRespondToQuery) : igmpRespondToQuery is enabled for IGMP packets. BIT 2(igmpUseBridgeIpAddress) : igmpUseBridgeIpAddress is enabled for IGMP packets. BIT 3(forceIGMPv2Down) : forceIGMPv2Down is enabled for subscriber side BIT 4(forceIGMPv2Up) : forceIGMPv2Up is enabled for uplink/network side

OBJECT-TYPE

Allow the configuration of the source IP address for packets that we originate upstream when doing IGMP Porxy on a bridge.

OBJECT-TYPE

This field does the following options,'BlockAsym(1)' blocks a learning bridge if flap is detected between it and an uplink bridge. 'BlockAll(2)' incorporates 'blockAsym(1)' but it also blocks a learning bridge if it flaps against another learning bridge.

OBJECT-TYPE

This parameter indicates DSCP value for igmp traffic. Valid code values: <0-63> Differentiated services codepoint value af11 Mark packets with AF11 dscp (001010) af12 Mark packets with AF12 dscp (001100) af13 Mark packets with AF13 dscp (001110) af21 Mark packets with AF21 dscp (010010) af22 Mark packets with AF22 dscp (010100) af23 Mark packets with AF23 dscp (010110) af31 Mark packets with AF31 dscp (011010) af32 Mark packets with AF32 dscp (011100) af33 Mark packets with AF33 dscp (011110) af41 Mark packets with AF41 dscp (100010) af42 Mark packets with AF42 dscp (100100) af43 Mark packets with AF43 dscp (100110) cs1 Mark packets with CS1(precedence 1) dscp (001000) cs2 Mark packets with CS2(precedence 2) dscp (010000) cs3 Mark packets with CS3(precedence 3) dscp (011000) cs4 Mark packets with CS4(precedence 4) dscp (100000) cs5 Mark packets with CS5(precedence 5) dscp (101000) cs6 Mark packets with CS6(precedence 6) dscp (110000) cs7 Mark packets with CS7(precedence 7) dscp (111000) default Mark packets with default dscp (000000) ef Mark packets with EF dscp (101110)

OBJECT-TYPE

A collection of bridgeIfLookupTable entries.

OBJECT-TYPE

Bridge IfLookup entries are created by the user or learned by the software in order to specify forwarding for a particular interface, vlanId/slanId, mac address or ip address. The INDEX value for bridgeIfLookupEntry consists of following 5 values: bridgeIfAddressType bridgeIfMacOrIpAddress bridgeIfVlanId ifIndex bridgeIfStagId If bridgeIfAddressType is set to unicast_mac(1), then bridgeIfMacOrIpAddress represents a MAC Address, and ifIndex, bridgeIfVlanId/Slanid and bridgeIfMacOrIpAddress are use for the bridge path. If bridgeIfAddressType is set to multicast_mac(2), then bridgeMacOrIpAddress represents a MAC Address, and ifIndex, bridgeIfVlanId/SlanId and bridgeIfMacOrIpAddress are used for bridge path. If bridgeIfAddressType is set to ip_address(3), then ifIndex and bridgeIfVlanId/SlanId are used for the bridge path.

OBJECT-TYPE

If bridgeIfAddressType is set to unicast_mac(1), then bridgeIfMacOrIpAddress represents a MAC Address, and ifIndex, bridgeIfVlanId and bridgeIfMacOrIpAddress are used for the bridge path. If bridgeIfAddressType is set to multicast_mac(2), then bridgeMacOrIpAddress represents a MAC Address, and ifIndex, bridgeIfVlanId and bridgeIfMacOrIpAddress are used for the bridge path. If bridgeIfAddressType is set to ip_address(3), then ifIndex and bridgeIfVlanId are used for the bridge path. If bridgeIfAddressType is set to dhcp_mac(4), or dhcp_ip(5), then the address is as desribed for types 1 and 3, respectively, and the address was learned by snooping DHCP packets. ipV6Address(6) is the same as ipAddress(3) except for IPv6 address format. dhcpV6Mac(7) is the same as dhacpMac(4) except for IPv6 address format. dhcpV7Ip(8) is the same as dhcpIp(5) except for IPv6 address format.

OBJECT-TYPE

If bridgeIfAddressType is set to FILTER_ENTRY_UNICAST_MAC(1) or to FILTER_ENTRY_MULTICAST_MAC(2), or to FILTER_ENTRY_DHCP_MAC(4), then bridgeIfMacOrIpAddress represents a MAC Address. If bridgeIfAddressType is set to FILTER_ENTRY_IP_ADDRESS(3), or to FILTER_ENTRY_DHCP_IP(5), then bridgeIfMacOrIpAddress represents an IP Address.

OBJECT-TYPE

If bridgeIfLookupStaticOrDynamic is set to 1, then this table entry is static and persistent. If bridgeIfLookupStaticOrDynamic is set to 2, then this table entry is learned and is not persistent.

OBJECT-TYPE

The object 'bridgeIfLookupFlush' allows a user to flush learned entries in the bridgeFilterTable when the ifIndex of the entry is not known. A combination of address type, MAC or IP address and vlan ID is used to determine the ifIndex of the entry to be removed. Setting the object to 'true' causes the flush action to occur. After the flush action is taken, the value of bridgeIfLookupFlush is immediately set back to 'false'.

OBJECT-TYPE

A collection of bridgeAddressLookupTable entries.

OBJECT-TYPE

BridgeAddressLookup entries are created by the user or learned by the software in order to specify forwarding for a particular interface, vlanId/slanId, mac address or ip address. The INDEX value for bridgeIfLookupEntry consists of following 5 values: ifIndex bridgeIfAddressType bridgeIfMacOrIpAddress bridgeIfVlanId bridgeIfStagId

OBJECT-TYPE

If bridgeAddressLookupStaticOrDynamic is set to 1, then this table entry is static and persistent. If bridgeAddressLookupStaticOrDynamic is set to 2, then this table entry is learned and is not persistent.

OBJECT-TYPE

The object 'bridgeIfAddressFlush' allows a user to flush learned entries in the bridgeFilterTable when the ifIndex of the entry is known. The ifIndex is used to determine which interface is to be removed. Setting the object to 'true' causes the flush action to occur. After the flush action is taken, the value of bridgeIfLookupFlush is immediately set back to 'false'.

OBJECT-IDENTITY

OBJECT-TYPE

A scalar representing the next available Group Index for Packet Rule Table Entries.

OBJECT-TYPE

A collection of entries each representing the next available index for that group.

OBJECT-TYPE

A packetRuleGroupNextIndexEntry contains the next available index for that packetRuleGroup.

OBJECT-TYPE

The next index available in a given packetRuleGroup for a new packetRuleEntry.

OBJECT-TYPE

A collection of packetRuleEntries.

OBJECT-TYPE

Packet Rule entries are created by the user in order to specify filtering or other packet manipulation for a particular interface.

OBJECT-TYPE

The index of a packetRuleEntry in a given packetRuleGroup.

OBJECT-TYPE

A 32-bit value which determines a filter to be applied to packets on the interface matching the pattern specified in packetRuleValue. The size and offset of the pattern in the packet will depend on packetRuleType. Bits may be set in packetRuleType determining properties of the filtering to be applied: BRIDGE_FORBID = 0x10 BRIDGE_INPUT = 0x20 BRIDGE_TERMINATE = 0x40 When BRIDGE_FORBID is set, packets matching the pattern are dropped; when it is clear, matching packets are forwarded. When BRIDGE_INPUT is set, filtering is applied to packets received on the interface; when it is clear, filtering is applied to packets to be transmitted on the interface. When BRIDGE_TERMINATE is set, processing of a packet matching the pattern ends the scan of filtering specifications; when it is clear, processing continues. Values of packetRuleType include DST_MAC_SWAP_STATIC = 0x25 DST_MAC_SWAP_DYNAMIC = 0x28 BRIDGE_INSERT_OPTION82 = 0x61 BRIDGE_DHCP_RELAY = 0x62 BRIDGE_INSERT_PPPOE_VENDOR_TAG = 0x63 BRIDGE_FORBID_OUI = 0x72 RATE_LIMIT_DISCARD = 0x64 COLOR_AWARE_RATE_LIMIT_DISCARD = 0x67

OBJECT-TYPE

A variable-length field whose meaning depends on packetRuleType. If bridgeForbidOui, it specifies a bit pattern to be matched in a packet, stored as a string, but specified in the pattern 'nn:nn:nn...nn:nn', where 'nn' is a hex number specifying a byte of the pattern. E.g. a packetRuleValue of '00:02:02' specifies the OUI to be dropped. If dhcpRelay, it is ascii integer which specifies dhcp subnet group. If bridgeInsertOption82, this value is ignored. If bridgeInsertPPPoEVendorTag, it specifies an ASCII string of up to 48 bytes to be inserted into PPPoE discovery packets (PADI/PADR) which transit this node. String will be inserted as a Vendor-Specific tag. If rateLimitDiscard, this value represents a maximum rate (in kbps). If aclAllow/aclDeny, a text string of the form: all | [Keyword NamedValue | Value[/N]]* where Keyword identifies the field of interest, Value is context dependent on the field, NamedValue is an alias for a Value. N indicates the number of most significant bits of Value to test. If omitted it defaults to the max allowed for the field.

OBJECT-TYPE

This object is used to create and remove rows in the table.

OBJECT-TYPE

A variable-length field whose meaning depends on packetRuleType.

OBJECT-TYPE

A variable-length field whose meaning depends on packetRuleType.

OBJECT-TYPE

A variable-length field whose meaning depends on packetRuleType.

OBJECT-TYPE

A variable-length field whose meaning depends on packetRuleType.

OBJECT-TYPE

A scalar representing the Group Index for a set of Packet Rule Table Entries.

OBJECT-TYPE

A variable-length field whose meaning depends on packetRuleType.

OBJECT-TYPE

A variable-length field whose meaning depends on packetRuleType.

OBJECT-TYPE

For PPPoA-to-PPPoE tables, provide a lookup by ifIndex into the PPPoE tables. If the session has not been created for this PPPoA ifIndex, then there will be no table data.

OBJECT-TYPE

Description.

OBJECT-TYPE

Destination mac address.

OBJECT-TYPE

Source mac address.

OBJECT-TYPE

PPPoE port's ifIndex.

OBJECT-TYPE

PPPoE session ID.

OBJECT-TYPE

SLan ID of BRAS.

OBJECT-TYPE

VLAN ID of BRAS.

OBJECT-TYPE

PPPoA encapsulation

OBJECT-IDENTITY

OBJECT-TYPE

set this field if you are using MSTP, use the name of the bridge as a key.

OBJECT-TYPE

This parameter is used if you are running MSTP only. Currently we don't support any revisions to MSTP, so revision 0 is default.

OBJECT-TYPE

The priority ID that will be advertised for this bridge.

OBJECT-TYPE

The protocol to initiate with. 3- MSTP, 2- RSTP, 0- STP.

OBJECT-TYPE

The delay used by STP bridges to transition Root and Designated Ports to Forwarding.

OBJECT-TYPE

The interval between periodic transmissions of Configuration Messages by Designated Ports. We only support a hello time of 2 currently.

OBJECT-TYPE

The initial value of the mdelayWhile and edgeDelayWhile timers. We currently only support a value of 3 for this timer.

OBJECT-TYPE

The transmit hold count is used by the Port Transmit state machine to limit transmission rate.

OBJECT-TYPE

The maximum age of the information transmitted by the bridge when it is the Root Bridge.

OBJECT-TYPE

The stpBind table is used to store the entries of stpBind which hold the relationship between the ifIndex on which STP is to run on, and the MSTP instance if any.

OBJECT-TYPE

stpBindEntry is used to specify the type of STP that is to run on an ifIndex. An InstanceID of 0 specifies RSTP. An InstanceId > 0 indicates MSTP.

OBJECT-TYPE

This is a hidden storage of the InstanceId of an entry.

OBJECT-TYPE

Description.

OBJECT-TYPE

PortPriority is used to specify the STP priority of this port.

OBJECT-TYPE

Description.

OBJECT-TYPE

Description.

OBJECT-TYPE

Description.

OBJECT-TYPE

A name for this mstp instance and vlanId.

OBJECT-TYPE

The bridgeStatsTable is used to access the statistics of the entries in the bridge table.

OBJECT-TYPE

Displays the bridge statistics table entries.

OBJECT-TYPE

Unicast packets received.

OBJECT-TYPE

Multicast packets received.

OBJECT-TYPE

Broadcast packets received.

OBJECT-TYPE

Unicast packets sent.

OBJECT-TYPE

Multicast packets sent.

OBJECT-TYPE

Broadcast packets sent.

OBJECT-TYPE

Error packets sent.

OBJECT-TYPE

Get the number of supported Ingress Stats available for a line card.

OBJECT-TYPE

Get the number of remaining Ingress Stats available for a line card

OBJECT-TYPE

Number of unicast packets dropped due to Bridge Packet Storm Detection threshold exceeded.

OBJECT-TYPE

Number of multicast packets dropped due to Bridge Packet Storm Detection threshold exceeded.

OBJECT-TYPE

Number of broadcast packets dropped due to Bridge Packet Storm Detection threshold exceeded.

OBJECT-TYPE

This counter reflects the number of times this interface has transitioned to the alarm state due to the Bridge Packet Storm Detection threshold being exceeded for a pre-defined number of seconds.

OBJECT-TYPE

This is a count of the number of bytes received. On-demand stats must be enabled for byte counters otherwise this counter is zero.

OBJECT-TYPE

This is a count of the number of bytes transmitted. On-demand stats must be enabled for byte counters otherwise this counter is zero.

OBJECT-TYPE

Linecard tick value when bridge was last cleared.

OBJECT-TYPE

Linecard current tick value.

OBJECT-TYPE

Linecard current tick value.

OBJECT-IDENTITY

OBJECT-TYPE

Bridge command ID value.

OBJECT-TYPE

Bridge command filters bit mask. If a bridge filter is enabled then the associated bridge filter value must be included in the SNMP packet. If the bridge filter mask is all zeros then no filters will be applied and the bridge command will apply to all bridges in the system.

OBJECT-TYPE

Bridge command 'ifIndex' filter value. If this object is included in the SNMP packet then the associated filter must be enabled in the bridge filter mask (bridgeCmdFilterMask).

OBJECT-TYPE

Bridge command 'VLAN' filter value. If this object is included in the SNMP packet then the associated filter must be enabled in the bridge filter mask (bridgeCmdFilterMask).

OBJECT-TYPE

Bridge command 'SLAN' filter value. If this object is included in the SNMP packet then the associated filter must be enabled in the bridge filter mask (bridgeCmdFilterMask).

OBJECT-TYPE

Bridge command 'SLOT' filter value. If this object is included in the SNMP packet then the associated filter must be enabled in the bridge filter mask (bridgeCmdFilterMask).

OBJECT-TYPE

Bridge command 'PORT' filter value. This is the ifIndex of the linegroup on which the bridge is stacked If this object is included in the SNMP packet then the associated filter must be enabled in the bridge filter mask (bridgeCmdFilterMask).

OBJECT-TYPE

Bridge command 'IP Address' filter value. If this object is included in the SNMP packet then the associated filter must be enabled in the bridge filter mask (bridgeCmdFilterMask).

OBJECT-TYPE

Bridge command 'MAC Address' filter value. If this object is included in the SNMP packet then the associated filter must be enabled in the bridge filter mask (bridgeCmdFilterMask).

OBJECT-IDENTITY

OBJECT-TYPE

This table contains information required for the management of EAPS domains.

OBJECT-TYPE

An entry exists for each EAPS domain in the system.

OBJECT-TYPE

This object contains the line group IfIndex of the Primary EAPS Port.

OBJECT-TYPE

This object contains the line group IfIndex of the Secondary EAPS Port.

OBJECT-TYPE

This object contains the VLAN ID of the control VLAN for this domain record. This is the VLAN ID used in EAPS control messages.

OBJECT-TYPE

If this value is True, then this record describes a Master Node. Otherwise, it describes a Transit Node.

OBJECT-TYPE

This object contains the Priority of the Control Vlan.

OBJECT-TYPE

This object contains the user assigned ASCII representation of the Domain Name for this record. This name must be unique device wide.

OBJECT-TYPE

This object contains the interval, in seconds, that a node sends Health Messages on the ring.

OBJECT-TYPE

On a Master Node, this object contains the timeout, in seconds, which the Master Node will report a Ring Fault if it does not receive a Health Message on the ring. On a Transit Node, this is the pre-forwarding delay timeout (also in seconds).

OBJECT-TYPE

On a Master Node, this object contains the number of contigious Health messages that may be dropped before the node declared a Ring Fault. This object is not used for a Transit node.

OBJECT-TYPE

If this object is set to True, then this node will send SNMP Traps on Ring State transition.

OBJECT-TYPE

If this value is TRUE, the EAPS state machine will transition through the initialization process to the Health state. It will begin passing Control Messages and allow Protected VLAN data through the EAPS Domain. If this value is FALSE, the EAPS state machine will transition through the reset process to the Inactivate state. It will stop passing Control Messages and prohibit Protected VLAN data from being passed through the EAPS Domain.

OBJECT-TYPE

This object is used to create and remove rows in the table. See eapsConfigEntry description for minimum requirements.

OBJECT-TYPE

This table contains information required for the management of a list of protected VLAN's in an EAPS domains.

OBJECT-TYPE

An entry for each VLAN ranges that is to be protected in the EAPS domain.

OBJECT-TYPE

This object is an index which indicates which entry in the Protected Vlan Table is being addressed. For example, a value of 5 would indicate that the 5th entry (row) of this table is being addressed. This entry, along with eapsConfigPrimaryLineGroup, eapsConfigSecondaryLineGroup, and eapsConfigControlVlan indices select which Protected Vlan Table entry for a given eaps-domain-record profile. The first three indices select the profile, this last index selects the N'th entry in that profile

OBJECT-TYPE

The eapsProtectedVlanLowerRange and eapsProtectedVlanUpperRange objects work in conjunction with one another to set the range of the protected vlans. If eapsProtectedVlanLowerRange is 0, then this indicates end of list. If eapsProtectedVlanLowerRange is not 0, but eapsProtectedVlanUpperRange is 0, then this would be have the same effect as both object having the same value and protect a single vlan ID. If they are both different and non-zero, then it specifies an inclusive range. Note that eapsProtectedVlanLowerRange must be numerically lower than eapsProtectedVlanUpperRange.

OBJECT-TYPE

The eapsProtectedVlanLowerRange and eapsProtectedVlanUpperRange objects work in conjunction with one another to set the range of the protected vlans. If eapsProtectedVlanLowerRange is 0, then this indicates end of list. If eapsProtectedVlanLowerRange is not 0, but eapsProtectedVlanUpperRange is 0, then this would be have the same effect as both object having the same value and protect a single vlan ID. If they are both different and non-zero, then it specifies an inclusive range. Note that eapsProtectedVlanLowerRange must be numerically lower than eapsProtectedVlanUpperRange.

OBJECT-TYPE

This object is used to create and remove rows in the table. See eapsProtectedVlanEntry description for minimum requirements.

OBJECT-TYPE

The domain name for the EAPS protected vlan entry.

OBJECT-TYPE

This table contains status of each EAPS domain state machine.

OBJECT-TYPE

The entry contains status of the domain's state machine.

OBJECT-TYPE

Previous state for the domain.

OBJECT-TYPE

Current state for the domain.

OBJECT-TYPE

EAPS statistics table.

OBJECT-TYPE

Displays the EAPS statistic table entries.

OBJECT-TYPE

Total EAPS control messages sent.

OBJECT-TYPE

Total EAPS control messages received.

OBJECT-IDENTITY

Place-holder object for EAPS traps, which must have a final digit of 0 in OID.

OBJECT-IDENTITY

Traps raised by EAPS state machine.

OBJECT-TYPE

EAPS topology table.

OBJECT-TYPE

Displays the EAPS topology table entries.

OBJECT-TYPE

This represents the link as primary or secondary.

OBJECT-TYPE

This represents the node number in the ring.

OBJECT-TYPE

This represents the domain name for this record.

OBJECT-TYPE

macAddress of the element in the ring.

OBJECT-TYPE

Ip addressed of the element in the ring.

OBJECT-TYPE

This represents whether the node is master or transit.

OBJECT-TYPE

This represents the primary link name.

OBJECT-TYPE

This represents the primary link state.

OBJECT-TYPE

This represents the secondary link name.

OBJECT-TYPE

This represents the secondary link state.

OBJECT-TYPE

The bridgeIgmpStatsTable is used to access the IGMP statistics for bridges.

OBJECT-TYPE

The bridgeIgmpStatsEntry holds IGMP stats for a bridge interface.

OBJECT-TYPE

general IGMP queries received.

OBJECT-TYPE

general IGMP queries transmitted.

OBJECT-TYPE

Specific IGMP queries received.

OBJECT-TYPE

Specific IGMP queries transmitted.

OBJECT-TYPE

Version 2 reports received (JOINs).

OBJECT-TYPE

Version 2 reports sent.

OBJECT-TYPE

IGMP leaves received.

OBJECT-TYPE

IGMP leaves transmitted.

OBJECT-TYPE

Unknown IGMP packets received.

OBJECT-TYPE

IGMP packet is bad received.

OBJECT-TYPE

Number of active muticast channels.

OBJECT-TYPE

Number of active multicast hosts.

OBJECT-TYPE

Number of IGMP V3 Queries received.

OBJECT-TYPE

Number of IGMP V3 queries sent.

OBJECT-TYPE

Number of IGMP V3 specific queries received.

OBJECT-TYPE

Number of IGMP V3 specific queries sent.

OBJECT-TYPE

Number of IGMP V3 reports received.

OBJECT-TYPE

Number of IGMP V3 reports sent.

OBJECT-IDENTITY

OBJECT-IDENTITY

Traps raised for bridge conditions.

OBJECT-IDENTITY

Bridge traps go under here - extra layer needed to ensure '0' in OID.

OBJECT-IDENTITY

OBJECT-TYPE

vlan/slan/macAddress for bridge

OBJECT-TYPE

The bridgeIgmpTable is used to access the IGMP data for bridges for when IGMP is in proxy mode and the IGMP status must be obtained from the linecard.

OBJECT-TYPE

BridgeIgmpEntry contains the igmp multicast data information for a bridge, indexed by ifIndex, hostMac, and mcastMac.

OBJECT-TYPE

IGMP slan identifier. Maximum value 4090 as defined by MAX_VLAN_NUM.

OBJECT-TYPE

IGMP vlan identifier. Maximum value 4090 as defined my MAX_VLAN_NUM

OBJECT-TYPE

IGMP Multicast MAC addressed to bridge port.

OBJECT-TYPE

IGMP Multicast IP addressed to bridge port.

OBJECT-TYPE

MAC address of end device receiving multicast packets.

OBJECT-TYPE

Count down timer before IGMP entry ages out.

OBJECT-TYPE

A collection of staticBridgePathEntries. The StaticBridgePath OID has the following format: OID psn MAC entries IPv4 entries IPv6 entries ---------- ------------- -------------- -------------- tlist[0] ifIndex ifIndex ifIndex tlist[1] address type address type address type tlist[2] vlan vlan vlan tlist[3] macAddr[0] IPv4[0] IPv6[0] tlist[4] macAddr[1] IPv4[1] IPv6[1] tlist[5] macAddr[2] IPv4[2] IPv6[2] tlist[6] macAddr[3] IPv4[3] IPv6[3] tlist[7] macAddr[4] zero IPv6[4] tlist[8] macAddr[5] zero IPv6[5] tlist[9] zero zero IPv6[6] tlist[10] zero zero IPv6[7] tlist[11] zero zero IPv6[8] tlist[12] zero zero IPv6[9] tlist[13] zero zero IPv6[10] tlist[14] zero zero IPv6[11] tlist[15] zero zero IPv6[12] tlist[16] zero zero IPv6[13] tlist[17] zero zero IPv6[14] tlist[18] zero zero IPv6[15] tlist[19] slan slan slan

OBJECT-TYPE

Static Path Bridge entries are created by the user in order to specify forwarding for a particular interface, vlanId, mac address or ip address, slanId (for QinQ). The INDEX value for staticBridgePathEntry consists of following 5 values: ifIndex staticBridgePathAddressType bridgeIfVlanId staticBridgePathMacOrIpAddress bridgeIfStagId If staticBridgeAddressType is set to macAddr(1), then staticBridgeMacOrIpAddress represents a MAC Address, and ifIndex, bridgeIfVlanId and staticBridgeMacOrIpAddress are used for the bridge path. If staticBridgeAddressType is set to ipAddr(2), then staticBridgeMacOrIpAddress represents an IP Address, and ifIndex, bridgeIfVlanId and staticBridgeMacOrIpAddress are used for the bridge path. If staticBridgeAddressType is set to vlanIdAddr(3), then ifIndex and bridgeIfVlanId are used for the bridge path. If staticBridgeAddressType is set to globalAddr(4), then ifIndex is used for the bridge path.

OBJECT-TYPE

If the staticBridgeAddressType is set to macAddr(1), then this field represents a MAC address. If the staticBridgeAddressType is set to ipAddr(2), then this field represents an IP address. The IP address can be four octets ( for IPv4 ) or sixteen octets ( for IPv6 ).

OBJECT-TYPE

If staticBridgeIPv6AddressType is set to macAddr(1), then staticBridgeMacOrIpAddress represents a MAC Address, and ifIndex, bridgeIfVlanId and staticBridgeMacOrIpAddress are used for the bridge path. If staticBridgeIPv6AddressType is set to ipAddr(2), then staticBridgeMacOrIpAddress represents an IP Address, and ifIndex, bridgeIfVlanId and staticBridgeMacOrIpAddress are used for the bridge path. If staticBridgeIPv6AddressType is set to vlanIdAddr(3) or intralinkAddr(7), then ifIndex and bridgeIfVlanId are used for the bridge path. If staticBridgeIPv6AddressType is set to globalAddr(4), globalIntralinkAddr(8), or mvrAddr(13) then ifIndex is used for the bridge path. If staticBridgeIPv6AddressType is set to dhcpAllowOui( 720901) then the first 3 bytes of the MAC address contains the OUI that we will allow DHCP addresses to be granted to, global scope. If staticBridgeIPv6AddressType is set to dhcpIpAddr(9), or to dhcpMacAddr(10), then the other fields are populated as for address types ipAddr and macAddr respectively, with the difference that these are secure entries, learned by snooping DHCP. If staticBridgeIPv6AddressType is set to vlanParms(14), then the static bridge entry holds parameters for the given VLAN and SLAN ID (for example, flap mode, unicast aging period, etc) and is not associated with any specific bridge, but with all bridges with the same VLAN/SLAN ID. For this reason, the IfIndex of this entry must be zero. If staticBridgeIPv6AddressType is set to secMvrAddr(15), then the static bridge entry holds parameters for a Secondary MVR path. The VLAN ID of this entry is the Secondary VLAN ID. If staticBridgeIPv6AddressType is set to ipAddrV6(16), then staticBridgeMacOrIpAddress represents an IPv6 Address, and ifIndex, bridgeIfVlanId and staticBridgeIPv6MacOrIpAddress are used for the bridge path. If staticBridgeIPv6AddressType is set to dhcpIpAddrV6(17), or to dhcpMacAddr(10), then the other fields are populated as for address types ipAddr and macAddr respectively, with the difference that these are secure entries, learned by snooping DHCP.

OBJECT-TYPE

Multicast Aging period in tenths of seconds for the specified VLAN. After the specified aging period is met, the VLAN address is deleted from the routing table. A value of 0 indicates that aging is turned off. Maximum value is 2147483647 tenths of seconds, which equates to approximately 2485.51 days.

OBJECT-TYPE

Used to create, modify or delete an entry in this table.

OBJECT-TYPE

This object enables or disable Flap Control in the Bridge Filter Table. The value 'disable(2)' turns Flap Control mode off. The values 'enable(3)' or 'fast(4) turn flap control mode on. 'Enable(3)' applies a hold time of 60 secs before allowing addr/IP to be moved to a new port, while 'fast(4)' applies a hold time of 0 secs. A value of 'default(1)' indicates 'Don't Care' and defaults to a disable or enable set by another entry.

OBJECT-TYPE

Multicast Aging period in tenths of seconds for the specified VLAN. After the specified aging period is met, the VLAN address is deleted from the routing table. A value of 0 indicates that aging is turned off. Maximum value is 2147483647 tenths of seconds, which equates to approximately 2485.51 days.

OBJECT-TYPE

How often (in seconds) we as a bridge inject IGMP query values into the stream.

OBJECT-TYPE

none : IGMP Snooping with Proxy reporting is disabled. BIT 0(igmpProcessJoinAndLeave) : igmpProcessJoinandLeave is enabled for IGMP packets. BIT 1(igmpRespondToQuery) : igmpRespondToQuery is enabled for IGMP packets. BIT 2(igmpUseBridgeIpAddress) : igmpUseBridgeIpAddress is enabled for IGMP packets.

OBJECT-TYPE

Allow the configuration of the source IP address for packets that we originate upstream when doing IGMP Porxy on a bridge.

OBJECT-TYPE

This field does the following options,'BlockAsym(1)' blocks a learning bridge if flap is detected between it and an uplink bridge. 'BlockAll(2)' incorporates 'blockAsym(1)' but it also blocks a learning bridge if it flaps against another learning bridge.

OBJECT-TYPE

This parameter indicates DSCP value for igmp traffic. Valid code values: <0-63> Differentiated services codepoint value af11 Mark packets with AF11 dscp (001010) af12 Mark packets with AF12 dscp (001100) af13 Mark packets with AF13 dscp (001110) af21 Mark packets with AF21 dscp (010010) af22 Mark packets with AF22 dscp (010100) af23 Mark packets with AF23 dscp (010110) af31 Mark packets with AF31 dscp (011010) af32 Mark packets with AF32 dscp (011100) af33 Mark packets with AF33 dscp (011110) af41 Mark packets with AF41 dscp (100010) af42 Mark packets with AF42 dscp (100100) af43 Mark packets with AF43 dscp (100110) cs1 Mark packets with CS1(precedence 1) dscp (001000) cs2 Mark packets with CS2(precedence 2) dscp (010000) cs3 Mark packets with CS3(precedence 3) dscp (011000) cs4 Mark packets with CS4(precedence 4) dscp (100000) cs5 Mark packets with CS5(precedence 5) dscp (101000) cs6 Mark packets with CS6(precedence 6) dscp (110000) cs7 Mark packets with CS7(precedence 7) dscp (111000) default Mark packets with default dscp (000000) ef Mark packets with EF dscp (101110)

OBJECT-TYPE

A collection of bridgePathIfLookupTable entries. The bridgePathIfLookup OID has the following format: OID psn MAC entries IPv4 entries IPv6 entries ---------- ------------- -------------- -------------- tlist[0] address type address type address type tlist[1] macAddr[0] IPv4[0] IPv6[0] tlist[2] macAddr[1] IPv4[1] IPv6[1] tlist[3] macAddr[2] IPv4[2] IPv6[2] tlist[4] macAddr[3] IPv4[3] IPv6[3] tlist[5] macAddr[4] zero IPv6[4] tlist[6] macAddr[5] zero IPv6[5] tlist[7] zero zero IPv6[6] tlist[8] zero zero IPv6[7] tlist[9] zero zero IPv6[8] tlist[10] zero zero IPv6[9] tlist[11] zero zero IPv6[10] tlist[12] zero zero IPv6[11] tlist[13] zero zero IPv6[12] tlist[14] zero zero IPv6[13] tlist[15] zero zero IPv6[14] tlist[16] zero zero IPv6[15] tlist[17] vlan vlan vlan tlist[18] ifIndex ifIndex ifIndex tlist[19] slan slan slan

OBJECT-TYPE

Bridge IfLookup entries are created by the user or learned by the software in order to specify forwarding for a particular interface, vlanId/slanId, mac address or ip address. The INDEX value for bridgeIfLookupEntry consists of following 5 values: bridgeIfAddressType bridgeIfMacOrIpAddress bridgeIfVlanId ifIndex bridgeIfStagId If bridgeIfAddressType is set to unicast_mac(1), then bridgeIfMacOrIpAddress represents a MAC Address, and ifIndex, bridgeIfVlanId/Slanid and bridgeIfMacOrIpAddress are use for the bridge path. If bridgeIfAddressType is set to multicast_mac(2), then bridgeMacOrIpAddress represents a MAC Address, and ifIndex, bridgeIfVlanId/SlanId and bridgeIfMacOrIpAddress are used for bridge path. If bridgeIfAddressType is set to ip_address(3), then ifIndex and bridgeIfVlanId/SlanId are used for the bridge path.

OBJECT-TYPE

If bridgeIfAddressType is set to unicast_mac(1), then bridgeIfMacOrIpAddress represents a MAC Address, and ifIndex, bridgeIfVlanId and bridgeIfMacOrIpAddress are used for the bridge path. If bridgeIfAddressType is set to multicast_mac(2), then bridgeMacOrIpAddress represents a MAC Address, and ifIndex, bridgeIfVlanId and bridgeIfMacOrIpAddress are used for the bridge path. If bridgeIfAddressType is set to ip_address(3), then ifIndex and bridgeIfVlanId are used for the bridge path. If bridgeIfAddressType is set to dhcp_mac(4), or dhcp_ip(5), then the address is as desribed for types 1 and 3, respectively, and the address was learned by snooping DHCP packets.

OBJECT-TYPE

If bridgeIfAddressType is set to FILTER_ENTRY_UNICAST_MAC(1) or to FILTER_ENTRY_MULTICAST_MAC(2), or to FILTER_ENTRY_DHCP_MAC(4), then bridgeIfMacOrIpAddress represents a MAC Address. If bridgeIfAddressType is set to FILTER_ENTRY_IP_ADDRESS(3), or to FILTER_ENTRY_DHCP_IP(5), then bridgeIfMacOrIpAddress represents an IP Address.

OBJECT-TYPE

If bridgeIfLookupStaticOrDynamic is set to 1, then this table entry is static and persistent. If bridgeIfLookupStaticOrDynamic is set to 2, then this table entry is learned and is not persistent.

OBJECT-TYPE

The object 'bridgeIfLookupFlush' allows a user to flush learned entries in the bridgeFilterTable when the ifIndex of the entry is not known. A combination of address type, MAC or IP address and vlan ID is used to determine the ifIndex of the entry to be removed. Setting the object to 'true' causes the flush action to occur. After the flush action is taken, the value of bridgeIfLookupFlush is immediately set back to 'false'.

OBJECT-TYPE

A collection of bridgePathAddressLookupTable entries. The bridgePathAddressLookup OID has the following format: OID psn MAC entries IPv4 entries IPv6 entries ---------- ------------- -------------- -------------- tlist[0] ifIndex ifIndex ifIndex tlist[1] address type address type address type tlist[2] macAddr[0] IPv4[0] IPv6[0] tlist[3] macAddr[1] IPv4[1] IPv6[1] tlist[4] macAddr[2] IPv4[2] IPv6[2] tlist[5] macAddr[3] IPv4[3] IPv6[3] tlist[6] macAddr[4] zero IPv6[4] tlist[7] macAddr[5] zero IPv6[5] tlist[8] zero zero IPv6[6] tlist[9] zero zero IPv6[7] tlist[10] zero zero IPv6[8] tlist[11] zero zero IPv6[9] tlist[12] zero zero IPv6[10] tlist[13] zero zero IPv6[11] tlist[14] zero zero IPv6[12] tlist[15] zero zero IPv6[13] tlist[16] zero zero IPv6[14] tlist[17] zero zero IPv6[15] tlist[18] vlan vlan vlan tlist[19] slan slan slan

OBJECT-TYPE

BridgePathAddressLookup entries are created by the user or learned by the software in order to specify forwarding for a particular interface, vlanId/slanId, mac address or ip address. The INDEX value for bridgePathLookupEntry consists of following 5 values: ifIndex bridgeIfAddressType bridgeIfMacOrIpAddress bridgeIfVlanId bridgeIfStagId

OBJECT-TYPE

If bridgePathAddressLookupStaticOrDynamic is set to 1, then this table entry is static and persistent. If bridgePathAddressLookupStaticOrDynamic is set to 2, then this table entry is learned and is not persistent.

OBJECT-TYPE

The object 'bridgePathAddressFlush' allows a user to flush learned entries in the bridgeFilterTable when the ifIndex of the entry is known. The ifIndex is used to determine which interface is to be removed. Setting the object to 'true' causes the flush action to occur. After the flush action is taken, the value of bridgePathLookupFlush is immediately set back to 'false'.

OBJECT-TYPE

This table contains runtime status for each bridge interface.

OBJECT-TYPE

Runtime status data for a single bridge.

OBJECT-TYPE

Values: up(1), UP down(2), DWN trouble(3), TRB notAvailable(4), NA initializing(5), INI adminDown(6), ADN adminStateTest(7), TST adminStateNone(8), N/S ready(9), RDY discovering(10), DSC unknown(11), ??? blocked(12), BLK pending(13), PND disabled(14), DIS learning(15), LRN forwarding(16), FWD blockedFlapping(17), BLF blockedPersistent(18), BLP blockedFlappingPersistenr(19), BFP

OBJECT-IDENTITY

OBJECT-IDENTITY