Wellfleet-OSPF-MIB
- Namespace
- nortel
- Source file
Wellfleet-OSPF-MIB- Digest
sha256:f2f08941e96a64c60178994fc0334f3dac8fb2bd304bda4b2fa4232aa485288f
Imports
| From | Symbols |
|---|---|
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP |
| SNMPv2-SMI | Counter32, Gauge32, IpAddress, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, iso |
| SNMPv2-TC | DisplayString, TEXTUAL-CONVENTION |
| Wellfleet-COMMON-MIB | wfOspfGroup |
Imported by
Nothing in this corpus imports this module.
Load order
Every file a consumer needs in order to load this module, dependencies first.
SNMPv2-CONF SNMPv2-SMI SNMPv2-TC Wellfleet-COMMON-MIB Wellfleet-OSPF-MIB
Objects
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| wfOspfGeneralGroup OBJECT-IDENTITY | 1.3.6.1.4.1.18.3.5.3.2.3.1 | |||
| wfOspfGeneralDelete OBJECT-TYPE 'This value determines whether OSPF is configured' | 1.3.6.1.4.1.18.3.5.3.2.3.1.1 | INTEGER {created(1), deleted(2)} | read-write | mandatory |
| wfOspfGeneralDisable OBJECT-TYPE 'The administrative status of OSPF in the router. The value 'enabled' denotes that the OSPF Process is active on at least one interface; 'disabled' disables it on all interfaces.' | 1.3.6.1.4.1.18.3.5.3.2.3.1.2 | INTEGER {enabled(1), disabled(2)} | read-write | mandatory |
| wfOspfGeneralState OBJECT-TYPE 'The state of OSPF' | 1.3.6.1.4.1.18.3.5.3.2.3.1.3 | INTEGER {up(1), down(2), init(3), notpresent(4)} | read-only | mandatory |
| wfOspfRouterId OBJECT-TYPE 'A 32-bit integer uniquely identifying the router in the Autonomous System. By convention, to ensure uniqueness, this should default to the value of one of the router's IP interface addresses.' REFERENCE 'OSPF Version 2, C.1 Global parameters' | 1.3.6.1.4.1.18.3.5.3.2.3.1.4 | IpAddress | read-write | mandatory |
| wfOspfVersionNumber OBJECT-TYPE 'The current version number of the OSPF protocol is 2.' REFERENCE 'OSPF Version 2, Title' | 1.3.6.1.4.1.18.3.5.3.2.3.1.5 | INTEGER | read-only | mandatory |
| wfOspfAreaBdrRtrStatus OBJECT-TYPE 'A flag to note whether this router is an area border router.' REFERENCE 'OSPF Version 2, Section 3 Splitting the AS into Areas' | 1.3.6.1.4.1.18.3.5.3.2.3.1.6 | INTEGER {true(1), false(2)} | read-only | mandatory |
| wfOspfASBdrRtrStatus OBJECT-TYPE 'A flag to note whether this router is an Autonomous System border router.' REFERENCE 'OSPF Version 2, Section 3.3 Classification of routers' | 1.3.6.1.4.1.18.3.5.3.2.3.1.7 | INTEGER {true(1), false(2)} | read-write | mandatory |
| wfOspfTOSSupport OBJECT-TYPE 'The router's support for type-of-service routing.' REFERENCE 'OSPF Version 2, Appendix F.1.2 Optional TOS support' | 1.3.6.1.4.1.18.3.5.3.2.3.1.8 | INTEGER {true(1), false(2)} | read-only | mandatory |
| wfOspfSpfHoldDown OBJECT-TYPE Hold Down Timer for the SPF. The SPF will run at most once per hold down timer value. A value of 0 means no hold down. | 1.3.6.1.4.1.18.3.5.3.2.3.1.9 | INTEGER (0..10) | read-write | mandatory |
| wfOspfSlotMask OBJECT-TYPE Slot mask for which slots OSPF is eligible to run on. The MSBit represents slot 1, the next most significant bit represents slot 2, and so on... Slots can be 1-14. Default is all slots on a BCN. | 1.3.6.1.4.1.18.3.5.3.2.3.1.10 | Gauge | read-write | mandatory |
| wfOspfNewAseMetricSupport OBJECT-TYPE A parameter to specify if the new style ASE metric support is enabled. The new metric is not compatible with the pre-8.0 ASE metrics. The new metric support should be disabled if the router is to interoperate with routers running a pre-8.0 OSPF version. | 1.3.6.1.4.1.18.3.5.3.2.3.1.11 | INTEGER {enabled(1), disabled(2)} | read-write | mandatory |
| wfOspfBackupDisable OBJECT-TYPE This parameter enables or disables the backup OSPF soloist's backup link state database. When the parameter is set to disabled the OSPF backup soloist will not maintain a copy of the OSPF link state database. | 1.3.6.1.4.1.18.3.5.3.2.3.1.12 | INTEGER {enabled(1), disabled(2)} | read-only | mandatory |
| wfOspfPrimaryLogMask OBJECT-TYPE A parameter to specify which OSPF log messages should be logged. This will only effect the Primary OSPF gate. Each bit represents a message as defined below. A 1 in that bit location means to log it and a 0 means not to put that log message in the log. Changing this value will NOT restart OSPF, but will take effct immediately(if there are any messages to be logged. bit 31 bit 0 +---------------------------------------+ | | +---------------------------------------+ bit0 Trace Messages bit1 INFO Level messages bit2 debug level messages bit3 OSPF interface state change messages bit4 Nbr state changes bit5 self-origination of LSA's bit6 receipt of new LSA's bit7 changes to OSPF`s Routing Table bit8 Bad LS requests, Ack's, or updates bit9 receipt of less recent LSA's bit10 receipt of more recent self-originated LSA's bit11 receipt of MAxAge LSA's (i.e. LSA's being flushed) bit12 - 31 reserved | 1.3.6.1.4.1.18.3.5.3.2.3.1.13 | Gauge | read-write | mandatory |
| wfOspfBackupLogMask OBJECT-TYPE A parameter to specify which OSPF log messages should be logged. This will only effect the Backup OSPF gate. Each bit represents a message as defined below. A 1 in that bit location means to log it a 0 means not to put that log message in the log. Changing this value will NOT restart OSPF, but will take effct immediately(if there are any messages to be logged. bit 31 bit 0 +---------------------------------------+ | | +---------------------------------------+ bit0 Trace Messages bit1 INFO Level messages bit2 debug level messages bit3 OSPF interface state change messages bit4 Nbr state changes bit5 self-origination of LSA's bit6 receipt of new LSA's bit7 changes to OSPF`s Routing Table bit8 Bad LS requests, Ack's, or updates bit9 receipt of less recent LSA's bit10 receipt of more recent self-originated LSA's bit11 receipt of MAxAge LSA's (i.e. LSA's being flushed) bit12 - 31 reserved | 1.3.6.1.4.1.18.3.5.3.2.3.1.14 | Gauge | read-only | mandatory |
| wfOspfAseTagDefault OBJECT-TYPE This parameter indicates how ASE tags will be generated for those ASEs whose tags are not altered by an export route filter or announce route policy. default(1) indicates that a zero value is used. automatic(2) indicates that an automatic tag will be generated as specified in RFC 1403. proprietary(3) indicates that the wellfleet proprietary scheme will be used. In this case, the next hop is used for IGP routes and the neighbor AS is used for EGP routes. | 1.3.6.1.4.1.18.3.5.3.2.3.1.15 | INTEGER {default(1), automatic(2), proprietary(3)} | read-write | mandatory |
| wfOspfPrimarySlot OBJECT-TYPE Slot on which OSPF Primary is running. Slots can be 1-14. Default is zero. | 1.3.6.1.4.1.18.3.5.3.2.3.1.16 | INTEGER | read-only | mandatory |
| wfOspfBackupSlot OBJECT-TYPE Slot on which OSPF Backup is running. Slots can be 1-14. Default is zero. | 1.3.6.1.4.1.18.3.5.3.2.3.1.17 | INTEGER | read-only | mandatory |
| wfOspfMaximumPath OBJECT-TYPE Maximum number of equal cost paths allowed for a network installed by OSPF. | 1.3.6.1.4.1.18.3.5.3.2.3.1.18 | INTEGER (1..5) | read-write | obsolete |
| wfOspfSlotPriority OBJECT-TYPE Comma-separated list of slots specifying the order in which slots should attempt to bring up OSPF soloist. They are listed in the decreasing order of priority. Slot with priority 0, i.e. the first entry in the list, is most likely to have OSPF soloist running on it. | 1.3.6.1.4.1.18.3.5.3.2.3.1.19 | DisplayString | read-write | mandatory |
| wfOspfLsdbCount OBJECT-TYPE Running count of LSDB entries | 1.3.6.1.4.1.18.3.5.3.2.3.1.20 | Counter | read-only | mandatory |
| wfOspfMulticastExtensions OBJECT-TYPE A Bit Mask indicating whether the router is forwarding IP multicast (Class D) datagrams based on the algorithms defined in the Multi- cast Extensions to OSPF. Bit 0, if set, indicates that the router can forward IP multicast datagrams in the router's directly attached areas (called intra-area mul- ticast routing). Bit 1, if set, indicates that the router can forward IP multicast datagrams between OSPF areas (called inter-area multicast routing). Bit 2, if set, indicates that the router can forward IP multicast datagrams between Auto- nomous Systems (called inter-AS multicast rout- ing). Only certain combinations of bit settings are allowed, namely: 0 (no multicast forwarding is enabled), 1 (intra-area multicasting only), 3 (intra-area and inter-area multicasting), 5 (intra-area and inter-AS multicasting) and 7 (multicasting everywhere). By default, no mul- ticast forwarding is enabled. | 1.3.6.1.4.1.18.3.5.3.2.3.1.21 | INTEGER | read-write | mandatory |
| wfOspfMulticastDeterministic OBJECT-TYPE This controls whether or not the deterministic variation of the MOSPF Dijkstra is run or not | 1.3.6.1.4.1.18.3.5.3.2.3.1.22 | INTEGER {nondeterministic(1), deterministicstrict(2), deterministicloose(3)} | read-write | mandatory |
| wfOspfMulticastRoutePinning OBJECT-TYPE This controls whether or not the route pinning variation of the MOSPF Dijkstra is run or not | 1.3.6.1.4.1.18.3.5.3.2.3.1.23 | INTEGER {nonpinned(1), pinned(2)} | read-write | mandatory |
| wfOspfOpaqueCapability OBJECT-TYPE This controls whether or not the router will accept and process OPAQUE LSAs | 1.3.6.1.4.1.18.3.5.3.2.3.1.24 | INTEGER {enabled(1), disabled(2)} | read-write | mandatory |
| wfOspfDeterministicMcastHoldDown OBJECT-TYPE This controls whether or not the Hold Down feature for the Deterministic MOSPF is enabled. If it is enabled, a data flow does not go out of an interface even if it would when the feature is disabled, unless there is a reservation for the flow on the interface | 1.3.6.1.4.1.18.3.5.3.2.3.1.25 | INTEGER {enabled(1), disabled(2)} | read-write | mandatory |
| wfMospfEntryTimeoutValue OBJECT-TYPE The timer value for timing out MOSPF forward entries. | 1.3.6.1.4.1.18.3.5.3.2.3.1.26 | INTEGER | read-write | mandatory |
| wfOspfMaxQueuedMcastPkts OBJECT-TYPE This controls how many mcast packets can be queued on each slot for all flows before the building of mcast trees finishes. If it is not 0, the first a few data packets for a mcast flow are queued before the building of the mcast tree finishes. Otherwise, packets are quietly dropped before the tree is calculated. | 1.3.6.1.4.1.18.3.5.3.2.3.1.27 | INTEGER | read-write | mandatory |
| wfOspfMcastUseDynTTL OBJECT-TYPE This controls whether dynamic TTL threshold is used. Data forwarding is a little bit faster when it is NOT used. Dynamic TTL means the TTL threshold may be different per (source, group, downstream) tuple. See MOSPF spec, section 2.3.4. | 1.3.6.1.4.1.18.3.5.3.2.3.1.28 | INTEGER {enabled(1), disabled(2)} | read-write | mandatory |
| wfOspfRfc1583Compatibility OBJECT-TYPE Controls the preference rules used when choosing among multiple AS-external-LSAs advertising the same destination. When set to 'enabled', the preference rules remain those specified by RFC 1583. When set to 'disabled', the preference rules are those stated in RFC 2178, which prevent routing loops when AS- external-LSAs for the same destination have been originated from different areas. | 1.3.6.1.4.1.18.3.5.3.2.3.1.29 | INTEGER {enabled(1), disabled(2)} | read-write | mandatory |
| wfOspfASEMcastEnable OBJECT-TYPE This attribute indicates whether AS External routes are multicast capable. If enabled, the advertising ASBR sets the MC-bit in the ASE-LSAs for those routes, so that they can be used for multicast purpose. If an MOSPF router works as an ASBR to support IGMP Relay, it should has this attribute set to 'enabled'. By default, all external routes are multicast incapable. If it's known that an ASBR's external routes can only be used for unicast, this attribute must be set to 'disabled' on the ASBR. For example, if an ASBR has a BGP connection to an ISP but the routes learned via BGP can't be used for multicast because external multicast traffic should be injected by another router with a DVMRP tunnel to Mbone, this attribute on the ASBR should be set to 'disabled'. | 1.3.6.1.4.1.18.3.5.3.2.3.1.30 | INTEGER {enabled(1), disabled(2)} | read-write | mandatory |
| wfOspfNssaBorderRouter OBJECT-TYPE `A flag to note whether this router NSSA border router' | 1.3.6.1.4.1.18.3.5.3.2.3.1.31 | INTEGER {yes(1), no(2)} | read-only | mandatory |
| wfOspfLsaRefreshMax OBJECT-TYPE `Maximum number of consecutive refreshes of self-originated Summary and External LSAs before applying a configured delay. A value of zero implies that there is no maximum.' | 1.3.6.1.4.1.18.3.5.3.2.3.1.32 | INTEGER | read-write | mandatory |
| wfOspfLsaRefreshDelay OBJECT-TYPE `Delay to apply between the maximum number of consecutive refreshes of self-originated Summary and External LSAs if a non-zero maximum is configured. The unit of delay is in seconds.' | 1.3.6.1.4.1.18.3.5.3.2.3.1.33 | INTEGER (1..5) | read-write | mandatory |
| wfOspfAggrUseMaxCost OBJECT-TYPE When area range is configured, sum net lsa is generated depends on this mib attribute: enabled: Use Max Metric to aggregate networks. See RFC2328 3.5 IP subnetting support. disabled: Use Min Metric to aggregate networks. Bay Router pre-14.40 version does this way. | 1.3.6.1.4.1.18.3.5.3.2.3.1.34 | INTEGER {enabled(1), disabled(2)} | read-write | mandatory |
| wfOspfFwdAddrComp OBJECT-TYPE When enabled allows OSPF to comply with RFC1583 with respect to forwarding address changes. When disabled OSPF remains compatiable with pre-14.00rev1D code. | 1.3.6.1.4.1.18.3.5.3.2.3.1.35 | INTEGER {enabled(1), disabled(2)} | read-write | mandatory |
| wfOspfMtuUseCommonDefault OBJECT-TYPE when this parameter is enabled, OSPF will use the MTU size of ethernet, that is, 1500 in all the interfaces regardless of what IP passes onto OSPF if the wfOspfMtuSize at the interface is set to 1(= Default) or 2. If wfOspfMtuSize is greater than 2 then OSPF will use wfOspfMtuSize as the MTU size at the interface. | 1.3.6.1.4.1.18.3.5.3.2.3.1.36 | INTEGER {enabled(1), disabled(2)} | read-write | mandatory |
| wfOspfAreaTable OBJECT-TYPE -- The OSPF Area Data Structure contains information -- regarding the various areas. The interfaces and -- virtual links are configured as part of these areas. -- Area 0.0.0.0, by definition, is the Backbone Area 'Information describing the configured parameters and cumulative statistics of the router's attached areas.' REFERENCE 'OSPF Version 2, Section 6 The Area Data Structure' | 1.3.6.1.4.1.18.3.5.3.2.3.2 | not-accessible | mandatory | |
| wfOspfAreaEntry OBJECT-TYPE 'Information describing the configured parameters and cumulative statistics of one of the router's attached areas.' | 1.3.6.1.4.1.18.3.5.3.2.3.2.1 | not-accessible | mandatory | |
| wfOspfAreaDelete OBJECT-TYPE This value determines if the OSPF router is configured with this area. | 1.3.6.1.4.1.18.3.5.3.2.3.2.1.1 | INTEGER {created(1), deleted(2)} | read-write | mandatory |
| wfOspfAreaDisable OBJECT-TYPE This value indicates the state of this area on the OSPF router. | 1.3.6.1.4.1.18.3.5.3.2.3.2.1.2 | INTEGER {enabled(1), disabled(2)} | read-write | mandatory |
| wfOspfAreaState OBJECT-TYPE This value indicates the state of the OSPF Area. | 1.3.6.1.4.1.18.3.5.3.2.3.2.1.3 | INTEGER {up(1), down(2)} | read-only | mandatory |
| wfOspfAreaId OBJECT-TYPE 'A 32-bit integer uniquely identifying an area. Area ID 0.0.0.0 is used for the OSPF backbone.' REFERENCE 'OSPF Version 2, Appendix C.2 Area parameters' | 1.3.6.1.4.1.18.3.5.3.2.3.2.1.4 | IpAddress | read-only | mandatory |
| wfOspfAuthType OBJECT-TYPE 'The authentication type specified for an area. Additional authentication types may be assigned locally on a per Area basis.' REFERENCE 'OSPF Version 2, Appendix E Authentication' -- none (0), -- simplePassword (1) -- reserved for future specification (2..255) -- reserved for AS specific values (> 255) | 1.3.6.1.4.1.18.3.5.3.2.3.2.1.5 | INTEGER {none(1), simple-password(2)} | read-write | mandatory |
| wfOspfImportASExtern OBJECT-TYPE 'The area's support for importing AS external link- state advertisements.' REFERENCE `OSPF NSSA Internet Draft, Appendix D: Configuration Parameters' | 1.3.6.1.4.1.18.3.5.3.2.3.2.1.6 | INTEGER {importExternal(1), importNoExternal(2), importNssa(3)} | read-write | mandatory |
| wfOspfStubMetric OBJECT-TYPE 'The metric value applied at the indicated type of service. By default, this equals the least metric at the type of service among the interfaces to other areas.' | 1.3.6.1.4.1.18.3.5.3.2.3.2.1.7 | INTEGER (1..16777215) | read-write | mandatory |
| wfOspfImportSum OBJECT-TYPE 'The area's support for importing Summary advertisements into a stub area. This variable should not be set unless wfOspfImportASExtern is set to FALSE' | 1.3.6.1.4.1.18.3.5.3.2.3.2.1.8 | INTEGER {true(1), false(2)} | read-write | mandatory |
| wfOspfSpfCnt OBJECT-TYPE The number of times the OSPF SPF algorithm has been run for this area. | 1.3.6.1.4.1.18.3.5.3.2.3.2.1.9 | Counter | read-only | mandatory |
| wfOspfPtpSpecCostEnable OBJECT-TYPE This value indicates the formula used to calculate the cost for point to point links. | 1.3.6.1.4.1.18.3.5.3.2.3.2.1.10 | INTEGER {enabled(1), disabled(2)} | read-write | mandatory |
| wfOspfAreaNssaTranslateCfg OBJECT-TYPE `Indicates whether or not an NSSA Border routes is configured to performing NSSA translation of type-7 LSAs into type-5 LSAs.' REFERENCE `OSPF NSSA Internet Draft, Appendix D: Configuration Parameters' | 1.3.6.1.4.1.18.3.5.3.2.3.2.1.11 | INTEGER {enabled(1), disabled(2)} | read-write | mandatory |
| wfOspfAreaNssaTranslateStatus OBJECT-TYPE `Indicates whether or not an NSSA Border routes is performing NSSA translation of type-7 LSAs into type-5 LSAs.' REFERENCE `OSPF NSSA Internet Draft, Appendix D: Configuration Parameters' | 1.3.6.1.4.1.18.3.5.3.2.3.2.1.12 | INTEGER {translating(1), nottranslating(2)} | read-only | mandatory |
| wfOspfAreaNssaOriginateDefaultRoute OBJECT-TYPE `whether or not an Type-7 default is originated by the ASBR' | 1.3.6.1.4.1.18.3.5.3.2.3.2.1.13 | INTEGER {enabled(1), disabled(2)} | read-write | mandatory |
| wfOspfAreaNssaPropagateDefaultRoute OBJECT-TYPE `Indicates whether or not the Type-7 default route LSA will have the propagate bit (P-bit) set. If the P-bit is set, the Type-7 default route LSA is translated into a Type-5 default route LSA and the Type-5 default route LSA is flooded into all non-stub areas. Otherwise the Type-7 default route LSA is not translated This parameter applies to NSSA internal ASBR only. For NSSA border ASBR, the P-bit is never set' | 1.3.6.1.4.1.18.3.5.3.2.3.2.1.14 | INTEGER {enabled(1), disabled(2)} | read-write | mandatory |
| wfOspfAreaNssaDefaultRoutePathType OBJECT-TYPE `The path type applied to the type-7 default route' REFERENCE `OSPF NSSA Internet Draft, Appendix D: Configuration Parameters' | 1.3.6.1.4.1.18.3.5.3.2.3.2.1.15 | INTEGER {type1(1), type2(2)} | read-write | mandatory |
| wfOspfLsdbTable OBJECT-TYPE -- OSPF Link State Database -- The Link State Database contains the Link State -- Advertisements from throughout the areas that the -- device is attached to. 'The OSPF Process's Links State Database.' REFERENCE 'OSPF Version 2, Section 12 Link State Advertisements' | 1.3.6.1.4.1.18.3.5.3.2.3.3 | not-accessible | mandatory | |
| wfOspfLsdbEntry OBJECT-TYPE 'A single Link State Advertisement.' | 1.3.6.1.4.1.18.3.5.3.2.3.3.1 | not-accessible | mandatory | |
| wfOspfLsdbAreaId OBJECT-TYPE 'The 32 bit identifier of the Area from which the LSA was received.' REFERENCE 'OSPF Version 2, Appendix C.2 Area parameters' | 1.3.6.1.4.1.18.3.5.3.2.3.3.1.1 | IpAddress | read-only | mandatory |
| wfOspfLsdbType OBJECT-TYPE 'The type of the link state advertisement. Each link state type has a separate advertisement format.' REFERENCE 'OSPF Version 2, Appendix A.4.1 The Link State Advertisement header' stubLink (0), routerLink (1), networkLink (2), summaryLink (3), asSummaryLink (4), asExternalLink (5), multicastlink (6), opaquelink (15), resourcelink (16) | 1.3.6.1.4.1.18.3.5.3.2.3.3.1.2 | INTEGER {routerlink(1), networklink(2), summarylink(3), assummarylink(4), asexternallink(5), multicastlink(6), nssaasexternallink(7), opaquelink(15), resourcelink(16)} | read-only | mandatory |
| wfOspfLsdbLSID OBJECT-TYPE 'The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement.' REFERENCE 'OSPF Version 2, Section 12.1.4 Link State ID' | 1.3.6.1.4.1.18.3.5.3.2.3.3.1.3 | IpAddress | read-only | mandatory |
| wfOspfLsdbRouterId OBJECT-TYPE 'The 32 bit number that uniquely identifies the originating router in the Autonomous System.' REFERENCE 'OSPF Version 2, Appendix C.1 Global parameters' | 1.3.6.1.4.1.18.3.5.3.2.3.3.1.4 | IpAddress | read-only | mandatory |
| wfOspfLsdbSequence OBJECT-TYPE -- Note that the OSPF Sequence Number is a 32 bit signed -- integer. It starts with the value '80000001'h, -- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h -- Thus, a typical sequence number will be very negative. 'The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.' REFERENCE 'OSPF Version 2, Section 12.1.6 LS sequence number' | 1.3.6.1.4.1.18.3.5.3.2.3.3.1.5 | INTEGER | read-only | mandatory |
| wfOspfLsdbAge OBJECT-TYPE 'This field is the age of the link state advertisement in seconds.' (OSPF_LSDBMINAGE = 0) REFERENCE 'OSPF Version 2, Section 12.1.1 LS age' | 1.3.6.1.4.1.18.3.5.3.2.3.3.1.6 | INTEGER (0..3600) | read-only | mandatory |
| wfOspfLsdbChecksum OBJECT-TYPE 'This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum.' REFERENCE 'OSPF Version 2, Section 12.1.7 LS checksum' | 1.3.6.1.4.1.18.3.5.3.2.3.3.1.7 | INTEGER | read-only | mandatory |
| wfOspfLsdbMetric OBJECT-TYPE 'Metric from LSA, if applicable.' | 1.3.6.1.4.1.18.3.5.3.2.3.3.1.8 | INTEGER | read-only | mandatory |
| wfOspfLsdbAseForwardAddr OBJECT-TYPE 'If an ASE, the forwarding address from the LSA.' | 1.3.6.1.4.1.18.3.5.3.2.3.3.1.9 | IpAddress | read-only | mandatory |
| wfOspfLsdbAseTag OBJECT-TYPE 'If an ASE, the External Route Tag from the LSA.' | 1.3.6.1.4.1.18.3.5.3.2.3.3.1.10 | Gauge | read-only | mandatory |
| wfOspfLsdbAseType OBJECT-TYPE 'If an ASE, the external metric type from the LSA.' | 1.3.6.1.4.1.18.3.5.3.2.3.3.1.11 | INTEGER {type1(1), type2(2)} | read-only | mandatory |
| wfOspfLsdbAdvLen OBJECT-TYPE 'The length of entire Link State Advertisement, including its header.' REFERENCE 'OSPF Version 2, Section 12 Link State Advertisements' | 1.3.6.1.4.1.18.3.5.3.2.3.3.1.12 | INTEGER | read-only | mandatory |
| wfOspfLsdbAdv OBJECT-TYPE 'This field is the actual OSPF advertisement in hexadecimal format' | 1.3.6.1.4.1.18.3.5.3.2.3.3.1.13 | OCTET STRING | read-only | mandatory |
| wfOspfAreaRangeTable OBJECT-TYPE 'A range if IP addresses specified by an IP address/IP network mask pair. For example, class B address range of X.X.X.X with a network mask of 255.255.0.0 includes all IP addresses from X.X.0.0 to X.X.255.255' REFERENCE 'OSPF Version 2, Appendix C.2 Area parameters' | 1.3.6.1.4.1.18.3.5.3.2.3.4 | not-accessible | mandatory | |
| wfOspfAreaRangeEntry OBJECT-TYPE | 1.3.6.1.4.1.18.3.5.3.2.3.4.1 | not-accessible | mandatory | |
| wfOspfAreaRangeDelete OBJECT-TYPE This value determines if an Area Range has been configured for the OSPF router. | 1.3.6.1.4.1.18.3.5.3.2.3.4.1.1 | INTEGER {created(1), deleted(2)} | read-write | mandatory |
| wfOspfAreaRangeDisable OBJECT-TYPE 'This variable displays the status of the entry. Setting it to 'DISBALED' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.' | 1.3.6.1.4.1.18.3.5.3.2.3.4.1.2 | INTEGER {enabled(1), disabled(2)} | read-write | mandatory |
| wfOspfAreaRangeState OBJECT-TYPE The state of the OSPF Area Range. | 1.3.6.1.4.1.18.3.5.3.2.3.4.1.3 | INTEGER {up(1), down(2)} | read-only | mandatory |
| wfOspfAreaRangeAreaID OBJECT-TYPE 'The Area the Address Range is to be found within.' REFERENCE 'OSPF Version 2, Appendix C.2 Area parameters' | 1.3.6.1.4.1.18.3.5.3.2.3.4.1.4 | IpAddress | read-only | mandatory |
| wfOspfAreaRangeNet OBJECT-TYPE 'The IP Address of the Net or Subnet indicated by the range.' REFERENCE 'OSPF Version 2, Appendix C.2 Area parameters' | 1.3.6.1.4.1.18.3.5.3.2.3.4.1.5 | IpAddress | read-only | mandatory |
| wfOspfAreaRangeMask OBJECT-TYPE 'The Subnet Mask that pertains to the Net or Subnet.' REFERENCE 'OSPF Version 2, Appendix C.2 Area parameters' | 1.3.6.1.4.1.18.3.5.3.2.3.4.1.6 | IpAddress | read-write | mandatory |
| wfOspfAreaRangeStatus OBJECT-TYPE 'Set to either Advertise or DoNotAdvertise. Routing information is condensed at area boundaries. External to the area, at most a single route is advertised for each address range. The route is advertised if and only if the addre range's Status is set to Advertise. Unadvertised ranges allow the existence of certain networks to be intentionally hidden from other areas. Status is set to Advertise by default.' REFERENCE 'OSPF Version 2, Appendix C.2' | 1.3.6.1.4.1.18.3.5.3.2.3.4.1.7 | INTEGER {advertise(1), block(2)} | read-write | mandatory |
| wfOspfAreaRangeMetric OBJECT-TYPE 'The metric to advertise into other areas as the distance from the OSPF router to any network in the range. The default of 0 means to use the value calculated by OSPF.' REFERENCE 'OSPF Version 2, Appendix C.2' | 1.3.6.1.4.1.18.3.5.3.2.3.4.1.8 | INTEGER | read-write | mandatory |
| wfOspfIfTable OBJECT-TYPE -- OSPF Interface Table -- The OSPF Interface Table augments the ifTable with OSPF -- specific information. 'The OSPF Interface Table describes the interfaces from the viewpoint of OSPF.' REFERENCE 'OSPF Version 2, Appendix C.3 Router interface parameters' | 1.3.6.1.4.1.18.3.5.3.2.3.5 | not-accessible | mandatory | |
| wfOspfIfEntry OBJECT-TYPE 'The OSPF Interface Entry describes one interface from the viewpoint of OSPF.' | 1.3.6.1.4.1.18.3.5.3.2.3.5.1 | not-accessible | mandatory | |
| wfOspfIfDelete OBJECT-TYPE This variable determines in an OSPF Interface has been configured on the router. | 1.3.6.1.4.1.18.3.5.3.2.3.5.1.1 | INTEGER {created(1), deleted(2)} | read-write | mandatory |
| wfOspfIfDisable OBJECT-TYPE 'The OSPF interface's administrative status. The value 'enabled' denotes that neighbor relationships may be formed on the interface, and the interface will be advertised as an internal route to some area. The value 'disabled' denotes that the interface is external to OSPF.' | 1.3.6.1.4.1.18.3.5.3.2.3.5.1.2 | INTEGER {enabled(1), disabled(2)} | read-write | mandatory |
| wfOspfIfState OBJECT-TYPE 'The OSPF Interface State.' down (1), loopback (2), waiting (3), pointToPoint (4), designatedRouter (5), backupDesignatedRouter (6), otherDesignatedRouter (7) | 1.3.6.1.4.1.18.3.5.3.2.3.5.1.3 | INTEGER {down(1), loopback(2), waiting(3), pointtopoint(4), designatedrouter(5), backupdesignatedrouter(6), otherdesignatedrouter(7)} | read-only | mandatory |
| wfOspfIfIpAddress OBJECT-TYPE 'The IP address of this OSPF interface.' | 1.3.6.1.4.1.18.3.5.3.2.3.5.1.4 | IpAddress | read-only | mandatory |
| wfOspfAddressLessIf OBJECT-TYPE 'For the purpose of easing the instancing of addressed and addressless interfaces; This variable takes the value 0 on interfaces with IP Addresses, and the corresponding value of ifIndex for interfaces having no IP Address.' | 1.3.6.1.4.1.18.3.5.3.2.3.5.1.5 | INTEGER | read-only | mandatory |
| wfOspfIfAreaId OBJECT-TYPE 'A 32-bit integer uniquely identifying the area to which the interface connects. Area ID 0.0.0.0 is used for the OSPF backbone.' default { '00000000'H } -- 0.0.0.0 | 1.3.6.1.4.1.18.3.5.3.2.3.5.1.6 | IpAddress | read-write | mandatory |
| wfOspfIfType OBJECT-TYPE 'The OSPF interface type. By way of a default, this field may be intuited from the corresponding value of ifType. Broadcast LANs, such as Ethernet and IEEE 802.5, take the value 'broadcast'. Medias which allow multiple devices to be connected but don't support a broadcast mechanism, such as X.25, take the value 'nbma'. Point to Point protocols take the value of 'pointtopoint'. Non-fully meshed technologies would take the value of either 'ietf' or 'pmp'. Passive interface take the value of 'passive'. An example topology is a Frame Relay cloud that does not have a PVC between every device on the cloud. broadcast (1), nbma (2), pointToPoint (3) point to multipoint - proprietary (4) point to multipoint - standard (5) passive (6) | 1.3.6.1.4.1.18.3.5.3.2.3.5.1.7 | INTEGER {broadcast(1), nbma(2), pointtopoint(3), pmp(4), ietf(5), passive(6)} | read-write | mandatory |
| wfOspfIfRtrPriority OBJECT-TYPE 'The priority of this interface. Used in multi-access networks, this field is used in the designated router election algorithm. The value 0 signifies that the router is not eligible to become the designated router on this particular network. In the event of a tie in this value, routers will use their router id as a tie breaker.' | 1.3.6.1.4.1.18.3.5.3.2.3.5.1.8 | INTEGER (0..255) | read-write | mandatory |
| wfOspfIfTransitDelay OBJECT-TYPE 'The estimated number of seconds it takes to transmit a link- state update packet over this interface.' | 1.3.6.1.4.1.18.3.5.3.2.3.5.1.9 | INTEGER (1..3600) | read-write | mandatory |
| wfOspfIfRetransInterval OBJECT-TYPE 'The number of seconds between link-state advertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database description and link-state request packets.' | 1.3.6.1.4.1.18.3.5.3.2.3.5.1.10 | INTEGER (1..3600) | read-write | mandatory |
| wfOspfIfHelloInterval OBJECT-TYPE 'The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for all routers attached to a common network.' | 1.3.6.1.4.1.18.3.5.3.2.3.5.1.11 | INTEGER (1..65535) | read-write | mandatory |
| wfOspfIfRtrDeadInterval OBJECT-TYPE 'The number of seconds that a router's Hello packets have not been seen before it's neighbors declare the router down. This should be some multiple of the Hello interval. This value must be the same for all routers attached to a common network.' | 1.3.6.1.4.1.18.3.5.3.2.3.5.1.12 | INTEGER (1..2147483647) | read-write | mandatory |
| wfOspfIfPollInterval OBJECT-TYPE 'The larger time interval, in seconds, between the Hello packets sent to an inactive non-broadcast multi- access neighbor.' | 1.3.6.1.4.1.18.3.5.3.2.3.5.1.13 | INTEGER (1..2147483647) | read-write | mandatory |
| wfOspfIfDesignatedRouter OBJECT-TYPE 'The IP Address of the Designated Router.' default { '00000000'H } -- 0.0.0.0 | 1.3.6.1.4.1.18.3.5.3.2.3.5.1.14 | IpAddress | read-only | mandatory |
| wfOspfIfBackupDesignatedRouter OBJECT-TYPE 'The IP Address of the Backup Designated Router.' default { '00000000'H } -- 0.0.0.0 | 1.3.6.1.4.1.18.3.5.3.2.3.5.1.15 | IpAddress | read-only | mandatory |
| wfOspfIfMetricCost OBJECT-TYPE 'The cost of using this type of service on this interface. The default value of the TOS 0 Metric is 10^8 / ifSpeed. The value FFFF is distinguished to mean 'no route via this TOS'.' | 1.3.6.1.4.1.18.3.5.3.2.3.5.1.16 | INTEGER (1..65535) | read-write | mandatory |
| wfOspfIfAuthKey OBJECT-TYPE 'The Authentication Key. If the Area's Authorization Type is simplePassword, and the key length is shorter than 8 octets, the agent will left adjust and zero fill to 8 octets. When read, ospfIfAuthKey always returns an Octet String of length zero.' default { '0000000000000000'H } -- 0.0.0.0.0.0.0.0 REFERENCE 'OSPF Version 2, Section 9 The Interface Data Structure' | 1.3.6.1.4.1.18.3.5.3.2.3.5.1.17 | OCTET STRING | read-write | mandatory |
| wfOspfIfTxHellos OBJECT-TYPE Number of OSPF Hello packets transmitted. | 1.3.6.1.4.1.18.3.5.3.2.3.5.1.18 | Counter | read-only | mandatory |
| wfOspfIfTxDBDescripts OBJECT-TYPE Number of OSPF DataBase Description packets transmitted. | 1.3.6.1.4.1.18.3.5.3.2.3.5.1.19 | Counter | read-only | mandatory |
| wfOspfIfTxLinkStateReqs OBJECT-TYPE Number of OSPF Link State Request packets transmitted. | 1.3.6.1.4.1.18.3.5.3.2.3.5.1.20 | Counter | read-only | mandatory |
| wfOspfIfTxLinkStateUpds OBJECT-TYPE Number of OSPF Link State Update packets transmitted. | 1.3.6.1.4.1.18.3.5.3.2.3.5.1.21 | Counter | read-only | mandatory |
| wfOspfIfTxLinkStateAcks OBJECT-TYPE Number of OSPF Link States Acknowledgements transmitted. | 1.3.6.1.4.1.18.3.5.3.2.3.5.1.22 | Counter | read-only | mandatory |
| wfOspfIfRxHellos OBJECT-TYPE Number of OSPF Hello packets received. | 1.3.6.1.4.1.18.3.5.3.2.3.5.1.23 | Counter | read-only | mandatory |
| wfOspfIfRxDBDescripts OBJECT-TYPE Number of OSPF DataBase Description packets received. | 1.3.6.1.4.1.18.3.5.3.2.3.5.1.24 | Counter | read-only | mandatory |
| wfOspfIfRxLinkStateReqs OBJECT-TYPE Number of OSPF Link State Requests received. | 1.3.6.1.4.1.18.3.5.3.2.3.5.1.25 | Counter | read-only | mandatory |
| wfOspfIfRxLinkStateUpds OBJECT-TYPE Number of OSPF Link State Updates received. | 1.3.6.1.4.1.18.3.5.3.2.3.5.1.26 | Counter | read-only | mandatory |
| wfOspfIfRxLinkStateAcks OBJECT-TYPE Number of OSPF Link State Acknowledgements received. | 1.3.6.1.4.1.18.3.5.3.2.3.5.1.27 | Counter | read-only | mandatory |
| wfOspfIfDrops OBJECT-TYPE Number of OSPF packets dropped because of invalid information in the packet. | 1.3.6.1.4.1.18.3.5.3.2.3.5.1.28 | Counter | read-only | mandatory |
| wfOspfMtuSize OBJECT-TYPE Configure MTU size per OSPF interface This parameter has the following values/meanings: 1 - Use the MTU specified by IP 2 - Use the MTU of ethernet, regardless of what IP says > 2 - Use this value as the actual MTU. If the value is smaller than what OSPF needs as a minimum then the mtu specified by IP is used. For example, 3 would never be used as an MTU. | 1.3.6.1.4.1.18.3.5.3.2.3.5.1.29 | INTEGER (1..10000) | read-write | mandatory |
| wfOspfIfMulticastForwarding OBJECT-TYPE The way multicasts should forwarded on this interface; not forwarded, forwarded as data link multicasts, or forwarded as data link uni- casts. Data link multicasting is not meaning- ful on point to point and NBMA interfaces, and setting ospfMulticastForwarding to 0 effective- ly disables all multicast forwarding. | 1.3.6.1.4.1.18.3.5.3.2.3.5.1.30 | INTEGER {blocked(1), multicast(2), unicast(3)} | read-write | mandatory |
| wfOspfIfOpaqueOn OBJECT-TYPE This controls whether or not OPAQUE LSAs are to be flooded out this interface or not. | 1.3.6.1.4.1.18.3.5.3.2.3.5.1.31 | INTEGER {on(1), off(2)} | read-write | mandatory |
| wfOspfIfBwRate OBJECT-TYPE Available BW (token bucket rate) on the intf | 1.3.6.1.4.1.18.3.5.3.2.3.5.1.32 | INTEGER | read-only | mandatory |
| wfOspfIfBwDepth OBJECT-TYPE Available BW (token bucket depth) on the intf | 1.3.6.1.4.1.18.3.5.3.2.3.5.1.33 | INTEGER | read-only | mandatory |
| wfOspfIfMtuMismatchDetect OBJECT-TYPE Controls the interpretation of the MTU field in the database description packet header. Per RFC 2178 the MTU indicates the largest size IP packet that an OSPF interface can receive. If the MTU is greater than that which the interface can receive the packet is ignored and thus, an adjacency is not formed. In RFC 1583 this field does not exist. The value 'enabled' denotes RFC 2178 processing of the MTU field. The value 'disabled' denotes RFC 1583 processing. | 1.3.6.1.4.1.18.3.5.3.2.3.5.1.34 | INTEGER {enabled(1), disabled(2)} | read-write | mandatory |
| wfOspfVirtIfTable OBJECT-TYPE -- OSPF Virtual Interface Table -- The Virtual Interface Table describes the virtual -- links that the OSPF Process is configured to -- carry on. 'Information about this router's virtual interfaces.' REFERENCE 'OSPF Version 2, Appendix C.4 Virtual link parameters' | 1.3.6.1.4.1.18.3.5.3.2.3.6 | not-accessible | mandatory | |
| wfOspfVirtIfEntry OBJECT-TYPE 'Information about a single Virtual Interface.' | 1.3.6.1.4.1.18.3.5.3.2.3.6.1 | not-accessible | mandatory | |
| wfOspfVirtIfDelete OBJECT-TYPE | 1.3.6.1.4.1.18.3.5.3.2.3.6.1.1 | INTEGER {created(1), deleted(2)} | read-write | mandatory |
| wfOspfVirtIfDisable OBJECT-TYPE 'This variable displays the validity or invalidity of the entry. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.' | 1.3.6.1.4.1.18.3.5.3.2.3.6.1.2 | INTEGER {enabled(1), disabled(2)} | read-write | mandatory |
| wfOspfVirtIfState OBJECT-TYPE 'OSPF virtual interface states.' down (1), -- these use the same encoding pointToPoint (4) -- as the ospfIfTable | 1.3.6.1.4.1.18.3.5.3.2.3.6.1.3 | INTEGER {down(1), pointtopoint(4)} | read-only | mandatory |
| wfOspfVirtIfAreaID OBJECT-TYPE 'The Transit Area that the Virtual Link traverses. By definition, this is not 0.0.0.0' | 1.3.6.1.4.1.18.3.5.3.2.3.6.1.4 | IpAddress | read-only | mandatory |
| wfOspfVirtIfNeighbor OBJECT-TYPE 'The Router ID of the Virtual Neighbor.' | 1.3.6.1.4.1.18.3.5.3.2.3.6.1.5 | IpAddress | read-only | mandatory |
| wfOspfVirtIfTransitDelay OBJECT-TYPE 'The estimated number of seconds it takes to transmit a link- state update packet over this interface.' | 1.3.6.1.4.1.18.3.5.3.2.3.6.1.6 | INTEGER (1..3600) | read-write | mandatory |
| wfOspfVirtIfRetransInterval OBJECT-TYPE 'The number of seconds between link-state advertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database description and link-state request packets. This value should be well over the expected round-trip time.' | 1.3.6.1.4.1.18.3.5.3.2.3.6.1.7 | INTEGER (1..3600) | read-write | mandatory |
| wfOspfVirtIfHelloInterval OBJECT-TYPE 'The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for the virtual neighbor.' | 1.3.6.1.4.1.18.3.5.3.2.3.6.1.8 | INTEGER (1..65535) | read-write | mandatory |
| wfOspfVirtIfRtrDeadInterval OBJECT-TYPE 'The number of seconds that a router's Hello packets have not been seen before it's neighbors declare the router down. This should be some multiple of the Hello interval. This value must be the same for the virtual neighbor.' | 1.3.6.1.4.1.18.3.5.3.2.3.6.1.9 | INTEGER (1..2147483647) | read-write | mandatory |
| wfOspfVirtIfAuthKey OBJECT-TYPE 'If Authentication Type is simplePassword, the device will left adjust and zero fill to 8 octets. When read, ospfVifAuthKey always returns a string of length zero.' REFERENCE 'OSPF Version 2, Section 9 The Interface Data Structure' | 1.3.6.1.4.1.18.3.5.3.2.3.6.1.10 | OCTET STRING | read-write | mandatory |
| wfOspfVirtIfTxHellos OBJECT-TYPE Number of OSPF Hello packets transmitted on Virtual Interfaces. | 1.3.6.1.4.1.18.3.5.3.2.3.6.1.11 | Counter | read-only | mandatory |
| wfOspfVirtIfTxDBDescripts OBJECT-TYPE Number of OSPF DataBase Description packets transmitted on Virtual Interfaces. | 1.3.6.1.4.1.18.3.5.3.2.3.6.1.12 | Counter | read-only | mandatory |
| wfOspfVirtIfTxLinkStateReqs OBJECT-TYPE Number of OSPF Link State Request packets transmitted on Virtual Interfaces. | 1.3.6.1.4.1.18.3.5.3.2.3.6.1.13 | Counter | read-only | mandatory |
| wfOspfVirtIfTxLinkStateUpds OBJECT-TYPE Number of OSPF Link State Update packets transmitted on Virtual Interfaces. | 1.3.6.1.4.1.18.3.5.3.2.3.6.1.14 | Counter | read-only | mandatory |
| wfOspfVirtIfTxLinkStateAcks OBJECT-TYPE Number of OSPF Link State Acknowledgement packets transmitted on Virtual Interfaces. | 1.3.6.1.4.1.18.3.5.3.2.3.6.1.15 | Counter | read-only | mandatory |
| wfOspfVirtIfRxHellos OBJECT-TYPE Number of OSPF Hello packets received on Virtual Interfaces. | 1.3.6.1.4.1.18.3.5.3.2.3.6.1.16 | Counter | read-only | mandatory |
| wfOspfVirtIfRxDBDescripts OBJECT-TYPE Number of OSPF DataBase Description packets received on Virtual Interfaces. | 1.3.6.1.4.1.18.3.5.3.2.3.6.1.17 | Counter | read-only | mandatory |
| wfOspfVirtIfRxLinkStateReqs OBJECT-TYPE Number of OSPF Link State Request packets recieved on Virtual Interfaces. | 1.3.6.1.4.1.18.3.5.3.2.3.6.1.18 | Counter | read-only | mandatory |
| wfOspfVirtIfRxLinkStateUpds OBJECT-TYPE Number of OSPF Link State Update packets received on Virtual Interfaces. | 1.3.6.1.4.1.18.3.5.3.2.3.6.1.19 | Counter | read-only | mandatory |
| wfOspfVirtIfRxLinkStateAcks OBJECT-TYPE Number of OSPF Link State Acknowledgement packets received on Virtual Interfaces. | 1.3.6.1.4.1.18.3.5.3.2.3.6.1.20 | Counter | read-only | mandatory |
| wfOspfVirtIfDrops OBJECT-TYPE Number of OSPF packets dropped on Virtual Interfaces. | 1.3.6.1.4.1.18.3.5.3.2.3.6.1.21 | Counter | read-only | mandatory |
| wfOspfNbrTable OBJECT-TYPE -- OSPF Neighbor Table -- The OSPF Neighbor Table describes all neighbors in -- the locality of the subject router. 'A table of non-virtual neighbor information.' REFERENCE 'OSPF Version 2, Section 10 The Neighbor Data Structure' | 1.3.6.1.4.1.18.3.5.3.2.3.7 | not-accessible | mandatory | |
| wfOspfNbrEntry OBJECT-TYPE 'The information regarding a single neighbor.' REFERENCE 'OSPF Version 2, Section 10 The Neighbor Data Structure' | 1.3.6.1.4.1.18.3.5.3.2.3.7.1 | not-accessible | mandatory | |
| wfOspfNbrDelete OBJECT-TYPE This variable indicates the existence of a static OSPF neighbor. | 1.3.6.1.4.1.18.3.5.3.2.3.7.1.1 | INTEGER {created(1), deleted(2)} | read-write | mandatory |
| wfOspfNbrDisable OBJECT-TYPE 'This variable displays the status of the entry. Setting it to 'DISABLED' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.' | 1.3.6.1.4.1.18.3.5.3.2.3.7.1.2 | INTEGER {enabled(1), disabled(2)} | read-write | mandatory |
| wfOspfNbrState OBJECT-TYPE 'The State of the relationship with this Neighbor.' REFERENCE 'OSPF Version 2, Section 10.1 Neighbor States' down (1), attempt (2), init (3), twoWay (4), exchangeStart (5), exchange (6), loading (7), full (8) | 1.3.6.1.4.1.18.3.5.3.2.3.7.1.3 | INTEGER {down(1), attempt(2), init(3), twoway(4), exchangstart(5), exchange(6), loading(7), full(8)} | read-only | mandatory |
| wfOspfNbrIpAddr OBJECT-TYPE 'The IP address of this neighbor.' | 1.3.6.1.4.1.18.3.5.3.2.3.7.1.4 | IpAddress | read-only | mandatory |
| wfOspfNbrIfAddr OBJECT-TYPE 'The Interface IP address for this neighbor.' | 1.3.6.1.4.1.18.3.5.3.2.3.7.1.5 | IpAddress | read-write | mandatory |
| wfOspfNbrAddressLessIndex OBJECT-TYPE ' On an interface having an IP Address, zero. On addressless interfaces, the corresponding value of ifIndex in the Internet Standard MIB. On row creation, this can be derived from the instance.' | 1.3.6.1.4.1.18.3.5.3.2.3.7.1.6 | INTEGER | read-only | mandatory |
| wfOspfNbrRtrId OBJECT-TYPE 'A 32-bit integer (represented as a type IpAddress) uniquely identifying the neighboring router in the Autonomous System.' default { '00000000'H } -- 0.0.0.0 | 1.3.6.1.4.1.18.3.5.3.2.3.7.1.7 | IpAddress | read-only | mandatory |
| wfOspfNbrOptions OBJECT-TYPE 'A Bit Mask corresponding to the neighbor's options field. Bit 0, if set, indicates that the area accepts and operates on external information; if zero, it is a stub area. Bit 1, if set, indicates that the system will operate on Type of Service metrics other than TOS 0. If zero, the neighbor will ignore all metrics except the TOS 0 metric.' REFERENCE 'OSPF Version 2, Section 12.1.2 Options' | 1.3.6.1.4.1.18.3.5.3.2.3.7.1.8 | INTEGER | read-only | mandatory |
| wfOspfNbrPriority OBJECT-TYPE 'The priority of this neighbor in the designated router election algorithm. The value 0 signifies that the neighbor is not eligible to become the designated router on this particular network.' This is the user configurable/changeable neighbor's priority | 1.3.6.1.4.1.18.3.5.3.2.3.7.1.9 | INTEGER (0..255) | read-write | mandatory |
| wfOspfNbrEvents OBJECT-TYPE 'The number of times this neighbor relationship has changed state, or an error has occurred.' | 1.3.6.1.4.1.18.3.5.3.2.3.7.1.10 | Counter | read-only | mandatory |
| wfOspfNbrLSRetransQLen OBJECT-TYPE 'The current length of the retransmission queue.' | 1.3.6.1.4.1.18.3.5.3.2.3.7.1.11 | Gauge | read-only | mandatory |
| wfOspfCurNbrPriority OBJECT-TYPE This value represents the priority of the neighbor as indicated in received Hello packets. In most cases, this will be the same as wfOspfCfgNbrPriority. If they are different, it indicates a misconfiguration | 1.3.6.1.4.1.18.3.5.3.2.3.7.1.12 | INTEGER | read-only | mandatory |
| wfOspfVirtNbrTable OBJECT-TYPE -- WFOSPF Virtual Neighbor Table -- This table describes all virtual neighbors. -- Since Virtual Links are configured in the -- virtual interface table, this table is read-only. 'A table of virtual neighbor information.' REFERENCE 'OSPF Version 2, ' | 1.3.6.1.4.1.18.3.5.3.2.3.8 | not-accessible | mandatory | |
| wfOspfVirtNbrEntry OBJECT-TYPE 'Virtual neighbor information.' REFERENCE 'OSPF Version 2, ' | 1.3.6.1.4.1.18.3.5.3.2.3.8.1 | not-accessible | mandatory | |
| wfOspfVirtNbrArea OBJECT-TYPE 'The Transit Area Identifier.' | 1.3.6.1.4.1.18.3.5.3.2.3.8.1.1 | IpAddress | read-only | mandatory |
| wfOspfVirtNbrRtrId OBJECT-TYPE 'A 32-bit integer uniquely identifying the neighboring router in the Autonomous System.' | 1.3.6.1.4.1.18.3.5.3.2.3.8.1.2 | IpAddress | read-only | mandatory |
| wfOspfVirtNbrIpAddr OBJECT-TYPE 'The IP address this Virtual Neighbor is using.' | 1.3.6.1.4.1.18.3.5.3.2.3.8.1.3 | IpAddress | read-only | mandatory |
| wfOspfVirtNbrOptions OBJECT-TYPE 'A bit map corresponding to the neighbor's options field. Thus, Bit 1, if set, indicates that the neighbor supports Type of Service Routing; if zero, no metrics other than TOS 0 are in use by the neighbor.' | 1.3.6.1.4.1.18.3.5.3.2.3.8.1.4 | INTEGER | read-only | mandatory |
| wfOspfVirtNbrState OBJECT-TYPE 'The state of the Virtual Neighbor Relationship.' down (1), attempt (2), init (3), twoWay (4), exchangeStart (5), exchange (6), loading (7), full (8) | 1.3.6.1.4.1.18.3.5.3.2.3.8.1.5 | INTEGER {down(1), attempt(2), init(3), twoway(4), exchangstart(5), exchange(6), loading(7), full(8)} | read-only | mandatory |
| wfOspfVirtNbrEvents OBJECT-TYPE 'The number of times this virtual link has changed its state, or an error has occurred.' | 1.3.6.1.4.1.18.3.5.3.2.3.8.1.6 | Counter | read-only | mandatory |
| wfOspfVirtNbrLSRetransQLen OBJECT-TYPE 'The current length of the retransmission queue.' | 1.3.6.1.4.1.18.3.5.3.2.3.8.1.7 | Gauge | read-only | mandatory |
| wfOspfDynNbrTable OBJECT-TYPE -- OSPF Dynamic Neighbor Table -- The OSPF Dynamic Neighbor Table describes all neighbors in -- the locality of the subject router learned during operation. 'A table of non-virtual neighbor information.' REFERENCE 'OSPF Version 2, Section 10 The Neighbor Data Structure' | 1.3.6.1.4.1.18.3.5.3.2.3.9 | not-accessible | mandatory | |
| wfOspfDynNbrEntry OBJECT-TYPE 'The information regarding a single neighbor.' REFERENCE 'OSPF Version 2, Section 10 The Neighbor Data Structure' | 1.3.6.1.4.1.18.3.5.3.2.3.9.1 | not-accessible | mandatory | |
| wfOspfDynNbrState OBJECT-TYPE 'The State of the relationship with this Neighbor.' REFERENCE 'OSPF Version 2, Section 10.1 Neighbor States' down (1), attempt (2), init (3), twoWay (4), exchangeStart (5), exchange (6), loading (7), full (8) | 1.3.6.1.4.1.18.3.5.3.2.3.9.1.1 | INTEGER {down(1), attempt(2), init(3), twoway(4), exchangstart(5), exchange(6), loading(7), full(8)} | read-only | mandatory |
| wfOspfDynNbrIpAddr OBJECT-TYPE 'The IP address of this neighbor.' | 1.3.6.1.4.1.18.3.5.3.2.3.9.1.2 | IpAddress | read-only | mandatory |
| wfOspfDynNbrIfAddr OBJECT-TYPE 'The Interface IP address for this neighbor.' | 1.3.6.1.4.1.18.3.5.3.2.3.9.1.3 | IpAddress | read-only | mandatory |
| wfOspfDynNbrAddressLessIndex OBJECT-TYPE ' On an interface having an IP Address, zero. On addressless interfaces, the corresponding value of ifIndex in the Internet Standard MIB. On row creation, this can be derived from the instance.' | 1.3.6.1.4.1.18.3.5.3.2.3.9.1.4 | INTEGER | read-only | mandatory |
| wfOspfDynNbrRtrId OBJECT-TYPE 'A 32-bit integer (represented as a type IpAddress) uniquely identifying the neighboring router in the Autonomous System.' default { '00000000'H } -- 0.0.0.0 | 1.3.6.1.4.1.18.3.5.3.2.3.9.1.5 | IpAddress | read-only | mandatory |
| wfOspfDynNbrOptions OBJECT-TYPE 'A Bit Mask corresponding to the neighbor's options field. Bit 0, if set, indicates that the area accepts and operates on external information; if zero, it is a stub area. Bit 1, if set, indicates that the system will operate on Type of Service metrics other than TOS 0. If zero, the neighbor will ignore all metrics except the TOS 0 metric.' REFERENCE 'OSPF Version 2, Section 12.1.2 Options' | 1.3.6.1.4.1.18.3.5.3.2.3.9.1.6 | INTEGER | read-only | mandatory |
| wfOspfDynNbrPriority OBJECT-TYPE 'The priority of this neighbor in the designated router election algorithm. The value 0 signifies that the neighbor is not eligible to become the designated router on this particular network.' | 1.3.6.1.4.1.18.3.5.3.2.3.9.1.7 | INTEGER | read-only | mandatory |
| wfOspfDynNbrEvents OBJECT-TYPE 'The number of times this neighbor relationship has changed state, or an error has occurred.' | 1.3.6.1.4.1.18.3.5.3.2.3.9.1.8 | Counter | read-only | mandatory |
| wfOspfDynNbrLSRetransQLen OBJECT-TYPE 'The current length of the retransmission queue.' | 1.3.6.1.4.1.18.3.5.3.2.3.9.1.9 | Gauge | read-only | mandatory |
| wfOspfBackupLsdbTable OBJECT-TYPE -- OSPF Backup Link State Database -- The Backup Link State Database contains the Link State -- Advertisements from throughout the areas that the -- device is attached to. 'The OSPF Process's Links State Database.' REFERENCE 'OSPF Version 2, Section 12 Link State Advertisements' | 1.3.6.1.4.1.18.3.5.3.2.3.10 | not-accessible | mandatory | |
| wfOspfBackupLsdbEntry OBJECT-TYPE 'A single Link State Advertisement.' | 1.3.6.1.4.1.18.3.5.3.2.3.10.1 | not-accessible | mandatory | |
| wfOspfBackupLsdbAreaId OBJECT-TYPE 'The 32 bit identifier of the Area from which the LSA was received.' REFERENCE 'OSPF Version 2, Appendix C.2 Area parameters' | 1.3.6.1.4.1.18.3.5.3.2.3.10.1.1 | IpAddress | read-only | mandatory |
| wfOspfBackupLsdbType OBJECT-TYPE 'The type of the link state advertisement. Each link state type has a separate advertisement format.' REFERENCE 'OSPF Version 2, Appendix A.4.1 The Link State Advertisement header' stubLink (0), routerLink (1), networkLink (2), summaryLink (3), asSummaryLink (4), asExternalLink (5) | 1.3.6.1.4.1.18.3.5.3.2.3.10.1.2 | INTEGER {routerlink(1), networklink(2), summarylink(3), assummarylink(4), asexternallink(5), nssaasexternallink(7)} | read-only | mandatory |
| wfOspfBackupLsdbLSID OBJECT-TYPE 'The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement.' REFERENCE 'OSPF Version 2, Section 12.1.4 Link State ID' | 1.3.6.1.4.1.18.3.5.3.2.3.10.1.3 | IpAddress | read-only | mandatory |
| wfOspfBackupLsdbRouterId OBJECT-TYPE 'The 32 bit number that uniquely identifies the originating router in the Autonomous System.' REFERENCE 'OSPF Version 2, Appendix C.1 Global parameters' | 1.3.6.1.4.1.18.3.5.3.2.3.10.1.4 | IpAddress | read-only | mandatory |
| wfOspfBackupLsdbSequence OBJECT-TYPE -- Note that the OSPF Sequence Number is a 32 bit signed -- integer. It starts with the value '80000001'h, -- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h -- Thus, a typical sequence number will be very negative. 'The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.' REFERENCE 'OSPF Version 2, Section 12.1.6 LS sequence number' | 1.3.6.1.4.1.18.3.5.3.2.3.10.1.5 | INTEGER | read-only | mandatory |
| wfOspfBackupLsdbAge OBJECT-TYPE 'This field is the age of the link state advertisement in seconds.' (OSPF_LSDBMINAGE = 0) REFERENCE 'OSPF Version 2, Section 12.1.1 LS age' | 1.3.6.1.4.1.18.3.5.3.2.3.10.1.6 | INTEGER (0..3600) | read-only | mandatory |
| wfOspfBackupLsdbChecksum OBJECT-TYPE 'This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum.' REFERENCE 'OSPF Version 2, Section 12.1.7 LS checksum' | 1.3.6.1.4.1.18.3.5.3.2.3.10.1.7 | INTEGER | read-only | mandatory |
| wfOspfBackupLsdbMetric OBJECT-TYPE 'Metric from LSA, if applicable.' | 1.3.6.1.4.1.18.3.5.3.2.3.10.1.8 | INTEGER | read-only | mandatory |
| wfOspfBackupLsdbAseForwardAddr OBJECT-TYPE 'If an ASE, the forwarding address from the LSA.' | 1.3.6.1.4.1.18.3.5.3.2.3.10.1.9 | IpAddress | read-only | mandatory |
| wfOspfBackupLsdbAseTag OBJECT-TYPE 'If an ASE, the External Route Tag from the LSA.' | 1.3.6.1.4.1.18.3.5.3.2.3.10.1.10 | Gauge | read-only | mandatory |
| wfOspfBackupLsdbAseType OBJECT-TYPE 'If an ASE, the external metric type from the LSA.' | 1.3.6.1.4.1.18.3.5.3.2.3.10.1.11 | INTEGER {type1(1), type2(2)} | read-only | mandatory |
| wfOspfBackupLsdbAdvLen OBJECT-TYPE 'The length of entire Link State Advertisement, including its header.' REFERENCE 'OSPF Version 2, Section 12 Link State Advertisements' | 1.3.6.1.4.1.18.3.5.3.2.3.10.1.12 | INTEGER | read-only | mandatory |
| wfOspfBackupLsdbAdv OBJECT-TYPE 'This field is the actual OSPF advertisement in hexadecimal format' | 1.3.6.1.4.1.18.3.5.3.2.3.10.1.13 | OCTET STRING | read-only | mandatory |
| wfMospfForwardTable OBJECT-TYPE | 1.3.6.1.4.1.18.3.5.3.2.3.11 | not-accessible | mandatory | |
| wfMospfForwardEntry OBJECT-TYPE A forwarding entry | 1.3.6.1.4.1.18.3.5.3.2.3.11.1 | not-accessible | mandatory | |
| wfMospfForwardSource OBJECT-TYPE The source IP address of this entry. It could be either a host, or a network, depending upon the value of wfMospfForwardSourceMask | 1.3.6.1.4.1.18.3.5.3.2.3.11.1.1 | IpAddress | read-only | mandatory |
| wfMospfForwardGroup OBJECT-TYPE The destinatino group address of this entry | 1.3.6.1.4.1.18.3.5.3.2.3.11.1.2 | IpAddress | read-only | mandatory |
| wfMospfForwardSourceMask OBJECT-TYPE The mask for the source of this entry. | 1.3.6.1.4.1.18.3.5.3.2.3.11.1.3 | IpAddress | read-only | mandatory |
| wfMospfForwardSourceNetMask OBJECT-TYPE The mask for the network that the source is on. | 1.3.6.1.4.1.18.3.5.3.2.3.11.1.4 | IpAddress | read-only | mandatory |
| wfMospfForwardFlag OBJECT-TYPE Flags associated with the entry. 0x10000000 (re)calculation of the entry not done yet 0x00000001 the entry is associated with a RSVP session | 1.3.6.1.4.1.18.3.5.3.2.3.11.1.5 | INTEGER | read-only | mandatory |
| wfMospfForwardUpstreamAddress OBJECT-TYPE The IP address of the upstream intf for the entry. | 1.3.6.1.4.1.18.3.5.3.2.3.11.1.6 | IpAddress | read-only | mandatory |
| wfMospfForwardUpstreamIfIndex OBJECT-TYPE The circuit number of the upstream intf for the entry. | 1.3.6.1.4.1.18.3.5.3.2.3.11.1.7 | INTEGER | read-only | mandatory |
| wfMospfForwardBwBucketDepth OBJECT-TYPE Depth parameter of the flow spec for the entry | 1.3.6.1.4.1.18.3.5.3.2.3.11.1.8 | INTEGER | read-only | mandatory |
| wfMospfForwardBwBucketRate OBJECT-TYPE Rate parameter of the flow spec for the entry | 1.3.6.1.4.1.18.3.5.3.2.3.11.1.9 | INTEGER | read-only | mandatory |
| wfMospfForwardAge OBJECT-TYPE The number of seconds since this route was last updated or otherwise determined to be correct. | 1.3.6.1.4.1.18.3.5.3.2.3.11.1.10 | INTEGER | read-only | mandatory |
| wfMospfForwardDownstream OBJECT-TYPE list of downstream intfs for this entry. Each one is in the format of (intf_addr (u_int32), intf_cct (u_int16), ttl (u_int16)) | 1.3.6.1.4.1.18.3.5.3.2.3.11.1.11 | OCTET STRING | read-only | mandatory |
| wfOspfNSSARangeTable OBJECT-TYPE -- OSPF NSSA Range Table -- The OSPF NSSA Range Table describes the Type-7 address -- ranges used in translation/aggregation of Type-7 LSAs -- into Type-5 LSAs. REFERENCE 'OSPF Internet Draft, Section 3.2 Type-7 Address Range' | 1.3.6.1.4.1.18.3.5.3.2.3.12 | not-accessible | mandatory | |
| wfOspfNSSARangeEntry OBJECT-TYPE | 1.3.6.1.4.1.18.3.5.3.2.3.12.1 | not-accessible | mandatory | |
| wfOspfNSSARangeDelete OBJECT-TYPE This value determines if an type-7 Range has been configured for the OSPF NSSA border router . | 1.3.6.1.4.1.18.3.5.3.2.3.12.1.1 | INTEGER {created(1), deleted(2)} | read-write | mandatory |
| wfOspfNSSARangeDisable OBJECT-TYPE `This variable displays the status of the entry. Setting it to `DISBALED' has the effect of rendering it inoperative. ' | 1.3.6.1.4.1.18.3.5.3.2.3.12.1.2 | INTEGER {enabled(1), disabled(2)} | read-write | mandatory |
| wfOspfNSSARangeNet OBJECT-TYPE `The IP Address of the Net or Subnet indicated by the range.' REFERENCE `OSPF NSSA Internet Draft, 3.2 type-7 address range' | 1.3.6.1.4.1.18.3.5.3.2.3.12.1.3 | IpAddress | read-only | mandatory |
| wfOspfNSSARangeMask OBJECT-TYPE `The Subnet Mask that pertains to the Net or Subnet.' REFERENCE `OSPF NSSA Internet Draft, 3.2 type-7 address range' | 1.3.6.1.4.1.18.3.5.3.2.3.12.1.4 | IpAddress | read-write | mandatory |
| wfOspfNSSARangeStatus OBJECT-TYPE `Set to either Advertise or DoNotAdvertise. Routing information is condensed at area boundaries. External to the area, at most a single route is advertised for each address range. The route is advertised if and only if the addre range's Status is set to Advertise. Unadvertised ranges allow the existence of certain networks to be intentionally hidden from other areas. Status is set to Advertise by default.' REFERENCE `OSPF NSSA Internet Draft, 3.2 type-7 address range' | 1.3.6.1.4.1.18.3.5.3.2.3.12.1.5 | INTEGER {advertise(1), block(2)} | read-write | mandatory |
| wfOspfNSSARangeExternRouteTag OBJECT-TYPE `External route tag. This value is used in the aggregated type-5 LSA' REFERENCE `OSPF NSSA Internet Draft, 3.2 type-7 address range' | 1.3.6.1.4.1.18.3.5.3.2.3.12.1.6 | INTEGER | read-write | mandatory |