MIBs Depot

WANSTATS-MIB

Registered at
1.3.6.1.4.1.11.2.3.7.6
Last updated
1999-11-18 00:00
Organization
Agilent Technologies NetMetrix Division
Namespace
hp
Source file
WANSTATS-MIB
Digest
sha256:46b1440bc095caf3882b2d073afdca11e9dfeb23115b94b99a5adbe91acf576d

Description

The MIB containing RMON media statistics for WAN links.

Contact

Agilent Technologies NetMetrix Division 5070 Centennial Blvd Colorado Springs, CO 80919

Imports

FromSymbols
RMON-MIBOwnerString
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP
SNMPv2-SMICounter64, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, enterprises, iso
SNMPv2-TCDisplayString, RowStatus, TEXTUAL-CONVENTION

Imported by

Nothing in this corpus imports this module.

Load order

Every file a consumer needs in order to load this module, dependencies first.

RMON-MIB
SNMPv2-CONF
SNMPv2-SMI
SNMPv2-TC
WANSTATS-MIB

Objects

NameOIDSyntaxAccessStatus
hp
OBJECT-IDENTITY
1.3.6.1.4.1.11
nm
OBJECT-IDENTITY
1.3.6.1.4.1.11.2
system
OBJECT-IDENTITY
1.3.6.1.4.1.11.2.3
netElement
OBJECT-IDENTITY
1.3.6.1.4.1.11.2.3.7
lanprobe
OBJECT-IDENTITY
1.3.6.1.4.1.11.2.3.7.6
general
OBJECT-IDENTITY
1.3.6.1.4.1.11.2.3.7.6.1
rmonExtension
OBJECT-IDENTITY
1.3.6.1.4.1.11.2.3.7.6.1.5
statsExtension
OBJECT-IDENTITY
1.3.6.1.4.1.11.2.3.7.6.1.5.1
wanStatsMIBObjects
OBJECT-IDENTITY
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1
wanSignalingStats
OBJECT-IDENTITY
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1
wanT1E1StatsTable
OBJECT-TYPE
T1/E1 signaling statistics.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1not-accessiblecurrent
wanT1E1StatsEntry
OBJECT-TYPE
Statistics for a T1/E1 interface. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1not-accessiblecurrent
wanT1E1StatsIndex
OBJECT-TYPE
The value of this object uniquely identifies this wanT1E1StatsTable entry.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.1INTEGER (1..65535)not-accessiblecurrent
wanT1E1StatsDataSource
OBJECT-TYPE
This object identifies the source of the data that this wanT1E1StatsEntry analyzes. This source can be any DS1 or E1 interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in MIB-II [RFC 1573] for the desired interface. The ifType value associated with the ifIndex can only be ds1(18).
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.2OBJECT IDENTIFIERread-createcurrent
wanT1E1StatsDropEvents
OBJECT-TYPE
The total number of events in which frames were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of frames dropped; it is just the number of times this condition has been detected.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.3Counter64read-onlycurrent
wanT1E1StatsInFrames
OBJECT-TYPE
The total number of frames seen originating from the far end of the link including errored frames.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.4Counter64read-onlycurrent
wanT1E1StatsOutFrames
OBJECT-TYPE
The total number of frames seen originating from the near end of the link including errored frames.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.5Counter64read-onlycurrent
wanT1E1StatsInOctets
OBJECT-TYPE
The sum of octets from all frames seen originating from the far end of the link including errored frames.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.6Counter64read-onlycurrent
wanT1E1StatsOutOctets
OBJECT-TYPE
The sum of octets from all frames seen originating from the near end of the link including errored frames.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.7Counter64read-onlycurrent
wanT1E1StatsESs
OBJECT-TYPE
For ESF and E1-CRC links an Errored Second is a second with one or more Path Code Violations OR one or more Out of Frame defects OR one or more Controlled Slip events OR a detected AIS defect. For D4 and E1-noCRC links, the presence of Bipolar Violations also triggers an Errored Second. This is not incremented during an Unavailable Second.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.8Counter64read-onlycurrent
wanT1E1StatsSESs
OBJECT-TYPE
A Severely Errored Second for ESF signals is a second with 320 or more Path Code Violation Error Events OR one or more Out of Frame defects OR a detected AIS defect. For E1-CRC signals, a Severely Errored Second is a second with 832 or more Path Code Violation error events OR one or more Out of Frame defects. For E1-noCRC signals, a Severely Errored Second is a 2048 LCVs or more. For D4 signals, a Severely Errored Second is a count of one-second intervals with Framing Error events, or an OOF defect, or 1544 LCVs or more. Controlled slips are not included in this parameter. This is not incremented during an Unavailable Second.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.9Counter64read-onlycurrent
wanT1E1StatsSEFSs
OBJECT-TYPE
An Severely Errored Framing Second is a second with one or more Out of Frame defects OR a detected AIS defect.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.10Counter64read-onlycurrent
wanT1E1StatsOOFs
OBJECT-TYPE
An OOF defect is the occurrence of a particular density of Framing Error events. For T1 links, an Out of Frame defect is declared when the receiver detects two or more framing errors within a 3 msec period for ESF signals and 0.75 msec for D4 signals, or two or more errors out of five or fewer consecutive framing-bits. For E1 links, an Out Of Frame defect is declared when three consecutive frame alignment signals have been received with an error (see G.706 Section 4.1 [17]). Once an Out Of Frame Defect is declared, the framer starts searching for a correct framing pattern. The Out of Frame defect ends when the signal is in frame. In-frame occurs when there are fewer than two frame bit errors within 3 msec period for ESF signals and 0.75 msec for D4 signals. For E1 links, in-frame occurs when a) in frame N the frame alignment signal is correct and b) in frame N+1 the frame alignment signal is absent (i.e., bit 2 in TS0 is a one) and c) in frame N+2 the frame alignment signal is present and correct.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.11Counter64read-onlycurrent
wanT1E1StatsUASs
OBJECT-TYPE
Unavailable Seconds (UAS) are calculated by counting the number of seconds that the interface is unavailable. The DS1 interface is said to be unavailable from the onset of 10 contiguous SESs, or the onset of the condition leading to a failure (see Failure States). If the condition leading to the failure was immediately preceded by one or more contiguous SESs, then the DS1 interface unavailability starts from the onset of these SESs. Once unavailable, and if no failure is present, the DS1 interface becomes available at the onset of 10 contiguous seconds with no SESs. Once unavailable, and if a failure is present, the DS1 interface becomes available at the onset of 10 contiguous seconds with no SESs, if the failure clearing time is less than or equal to 10 seconds. If the failure clearing time is more than 10 seconds, the DS1 interface becomes available at the onset of 10 contiguous seconds with no SESs, or the onset period leading to the successful clearing condition, whichever occurs later. With respect to the DS1 error counts, all counters are incremented while the DS1 interface is deemed available. While the interface is deemed unavailable, the only count that is incremented is UASs.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.12Counter64read-onlycurrent
wanT1E1StatsCSSs
OBJECT-TYPE
A Controlled Slip Second is a one-second interval containing one or more controlled slips.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.13Counter64read-onlycurrent
wanT1E1StatsPCVs
OBJECT-TYPE
A Path Coding Violation error event is a frame synchronization bit error in the D4 and E1-noCRC formats, or a CRC error in the ESF and E1-CRC formats.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.14Counter64read-onlycurrent
wanT1E1StatsLESs
OBJECT-TYPE
A Line Errored Second, according to T1M1.3, is a second in which one or more Line Code Violation error events were detected. While many implementations are currently unable to detect the zero strings, it is expected that interface manufacturers will add this capability in deference to ANSI; therefore, it will become available in time. In the T1M1.3 specification, near end Line Code Violations and far end Line Errored Seconds are counted. For consistency, we count Line Errored Seconds at both ends.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.15Counter64read-onlycurrent
wanT1E1StatsBESs
OBJECT-TYPE
A Bursty Errored Second (also known as Errored Second type B) is a second with fewer than 320 and more than 1 Path Coding Violation error events, no Severely Errored Frame defects and no detected incoming AIS defects. Controlled slips are not included in this parameter. This is not incremented during an Unavailable Second.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.16Counter64read-onlycurrent
wanT1E1StatsDMs
OBJECT-TYPE
A Degraded Minute is one in which the estimated error rate exceeds 1E-6 but does not exceed 1E-3 (see G.821 [15]). Degraded Minutes are determined by collecting all of the Available Seconds, removing any Severely Errored Seconds grouping the result in 60-second long groups and counting a 60-second long group (a.k.a., minute) as degraded if the cumulative errors during the seconds present in the group exceed 1E-6. Available seconds are merely those seconds which are not Unavailable as described below.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.17Counter64read-onlycurrent
wanT1E1StatsLCVs
OBJECT-TYPE
A Line Coding Violation (LCV) is the occurrence of either a Bipolar Violation (BPV) or Excessive Zeroes (EXZ) Error Event.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.18Counter64read-onlycurrent
wanT1E1StatsLOFs
OBJECT-TYPE
For T1 links, the Loss Of Frame failure is declared when an OOF or LOS defect has persisted for T seconds, where 2 <= T <= 10. The Loss Of Frame failure is cleared when there have been no OOF or LOS defects during a period T where 0 <= T <= 20. Many systems will perform 'hit integration' within the period T before declaring or clearing the failure e.g., see TR 62411 [16]. For E1 links, the Loss Of Frame Failure is declared when an OOF defect is detected.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.19Counter64read-onlycurrent
wanT1E1StatsLOSs
OBJECT-TYPE
For T1, the Loss Of Signal failure is declared upon observing 175 +/- 75 contiguous pulse positions with no pulses of either positive or negative polarity. The LOS failure is cleared upon observing an average pulse density of at least 12.5% over a period of 175 +/- 75 contiguous pulse positions starting with the receipt of a pulse. For E1 links, the Loss Of Signal failure is declared when greater than 10 consecutive zeroes are detected (see O.162 Section 3.4.4).
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.20Counter64read-onlycurrent
wanT1E1StatsRAIs
OBJECT-TYPE
The Far End Alarm failure is also known as 'Yellow Alarm' in the T1 case and 'Distant Alarm' in the E1 case. For D4 links, the Far End Alarm failure is declared when bit 6 of all channels has been zero for at least 335 ms and is cleared when bit 6 of at least one channel is non-zero for a period T, where T is usually less than one second and always less than 5 seconds. The Far End Alarm failure is not declared for D4 links when a Loss of Signal is detected. For ESF links, the Far End Alarm failure is declared if the Yellow Alarm signal pattern occurs in at least seven out of ten contiguous 16-bit pattern intervals and is cleared if the Yellow Alarm signal pattern does not occur in ten contiguous 16-bit signal pattern intervals. For E1 links, the Far End Alarm failure is declared when bit 3 of time-slot zero is received set to one on two consecutive occasions. The Far End Alarm failure is cleared when bit 3 of time-slot zero is received set to zero.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.21Counter64read-onlycurrent
wanT1E1StatsAISs
OBJECT-TYPE
The Alarm Indication Signal failure is declared when an AIS defect is detected at the input and the AIS defect still exists after the Loss Of Frame failure (which is caused by the unframed nature of the 'all-ones' signal) is declared. The AIS failure is cleared when the Loss Of Frame failure is cleared.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.22Counter64read-onlycurrent
wanT1E1StatsTS16AISs
OBJECT-TYPE
For E1 links, the TS16 Alarm Indication Signal failure is declared when time-slot 16 is received as all ones for all frames of two consecutive multiframes (see G.732 Section 4.2.6). This condition is never declared for T1.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.23Counter64read-onlycurrent
wanT1E1StatsLOMFs
OBJECT-TYPE
The Loss Of MultiFrame failure is declared when two consecutive multiframe alignment signals (bits 4 through 7 of TS16 of frame 0) have been received with an error. The Loss Of Multiframe failure is cleared when the first correct multiframe alignment signal is received. The Loss Of Multiframe failure can only be declared for E1 links operating with G.732 [18] framing (sometimes called 'Channel Associated Signalling' mode).
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.24Counter64read-onlycurrent
wanT1E1StatsFarLOMFs
OBJECT-TYPE
The Far End Loss Of Multiframe failure is declared when bit 2 of TS16 of frame 0 is received set to one on two consecutive occasions. The Far End Loss Of Multiframe failure is cleared when bit 2 of TS16 of frame 0 is received set to zero. The Far End Loss Of Multiframe failure can only be declared for E1 links operating in 'Channel Associated Signalling' mode.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.25Counter64read-onlycurrent
wanT1E1StatsOwner
OBJECT-TYPE
The entity that configured this entry.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.26OwnerStringread-createcurrent
wanT1E1StatsStatus
OBJECT-TYPE
The status of this wanT1E1StatsTable entry.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.27RowStatusread-createcurrent
wanVSeriesStatsTable
OBJECT-TYPE
V-series interface statistics.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2not-accessiblecurrent
wanVSeriesStatsEntry
OBJECT-TYPE
The statistics for a V-series interface. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1not-accessiblecurrent
wanVSeriesStatsIndex
OBJECT-TYPE
The value of this object uniquely identifies this wanVSeriesStatsTable entry.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.1INTEGER (1..65535)not-accessiblecurrent
wanVSeriesStatsDataSource
OBJECT-TYPE
This object identifies the source of the data that this wanVSeriesStatsEntry analyzes. This source can be and V-series interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in MIB-II [RFC 1573] for the desired interface. The ifType value associated with the ifIndex can only be rs232(33) , v35(45), v11(64), or v36(65).
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.2OBJECT IDENTIFIERread-createcurrent
wanVSeriesStatsDropEvents
OBJECT-TYPE
The total number of events in which frames were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of frames dropped; it is just the number of times this condition has been detected.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.3Counter64read-onlycurrent
wanVSeriesStatsInFrames
OBJECT-TYPE
The total number of frames seen originating from the far end of the link including errored.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.4Counter64read-onlycurrent
wanVSeriesStatsOutFrames
OBJECT-TYPE
The total number of frames seen originating from the near end of the link including errored frames.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.5Counter64read-onlycurrent
wanVSeriesStatsInOctets
OBJECT-TYPE
The sum of octets from all frames seen originating from the far end of the link including errored frames.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.6Counter64read-onlycurrent
wanVSeriesStatsOutOctets
OBJECT-TYPE
The sum of octets from all frames seen originating from the near end of the link including errored frames.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.7Counter64read-onlycurrent
wanVSeriesStatsInFCSs
OBJECT-TYPE
Total number of frames with an invalid frame check from the far end of the link.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.8Counter64read-onlycurrent
wanVSeriesStatsOutFCSs
OBJECT-TYPE
Total number of frames with an invalid frame check from the near end of the link.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.9Counter64read-onlycurrent
wanVSeriesStatsInOverruns
OBJECT-TYPE
Total number of frames from the far end of the link that failed to be received because the receiver did not accept the data in time.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.10Counter64read-onlycurrent
wanVSeriesStatsOutOverruns
OBJECT-TYPE
Total number of frames from the near end of the link that failed to be received because the receiver did not accept the data in time.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.11Counter64read-onlycurrent
wanVSeriesStatsInterruptedFrames
OBJECT-TYPE
Total number of frames that failed to be received or transmitted on the port due to loss of modem signals.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.12Counter64read-onlycurrent
wanVSeriesStatsInAbortedFrames
OBJECT-TYPE
Number of frames from the far end of the link aborted on the port due to receiving an abort sequence.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.13Counter64read-onlycurrent
wanVSeriesStatsOutAbortedFrames
OBJECT-TYPE
Number of frames from the near end of the link aborted on the port due to receiving an abort sequence.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.14Counter64read-onlycurrent
wanVSeriesStatsOwner
OBJECT-TYPE
The entity that configured this entry.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.15OwnerStringread-createcurrent
wanVSeriesStatsStatus
OBJECT-TYPE
The status of this wanVSeriesStatsTable entry.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.16RowStatusread-createcurrent
wanHssiStatsTable
OBJECT-TYPE
HSSI interface statistics.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3not-accessibledeprecated
wanHssiStatsEntry
OBJECT-TYPE
The statistics for a HSSI interface. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1not-accessibledeprecated
wanHssiStatsIndex
OBJECT-TYPE
The value of this object uniquely identifies this wanHssiStatsTable entry.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.1INTEGER (1..65535)not-accessibledeprecated
wanHssiStatsDataSource
OBJECT-TYPE
This object identifies the source of the data that this wanT1E1StatsEntry analyzes. This source can be any HSSI interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in MIB-II [RFC 1573] for the desired interface. The ifType value associated with the ifIndex can only be hssi(46).
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.2OBJECT IDENTIFIERread-createdeprecated
wanHssiStatsDropEvents
OBJECT-TYPE
The total number of events in which frames were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of frames dropped; it is just the number of times this condition has been detected.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.3Counter64read-onlydeprecated
wanHssiStatsInFrames
OBJECT-TYPE
The total number of frames seen originating from the far end of the link including errored frames.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.4Counter64read-onlydeprecated
wanHssiStatsOutFrames
OBJECT-TYPE
The total number of frames seen originating from the near end of the link including errored frames.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.5Counter64read-onlydeprecated
wanHssiStatsInOctets
OBJECT-TYPE
The sum of octets from all frames seen originating from the far end of the link including errored frames.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.6Counter64read-onlydeprecated
wanHssiStatsOutOctets
OBJECT-TYPE
The sum of octets from all frames seen originating from the near end of the link including errored frames.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.7Counter64read-onlydeprecated
wanHssiStatsRxLongFrames
OBJECT-TYPE
Number of long frames from the far end of the link.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.8Counter64read-onlydeprecated
wanHssiStatsRxCrcErrors
OBJECT-TYPE
Number of frames from far end of link with CRC errors.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.9Counter64read-onlydeprecated
wanHssiStatsRxOverruns
OBJECT-TYPE
Number of frames from far end of link with FIFO overrun errors.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.10Counter64read-onlydeprecated
wanHssiStatsRxAborts
OBJECT-TYPE
Number of frames from far end of link with abort status.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.11Counter64read-onlydeprecated
wanHssiStatsTxAborts
OBJECT-TYPE
Number of frames from near end of link with internal abort errors.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.12Counter64read-onlydeprecated
wanHssiStatsTxUnderruns
OBJECT-TYPE
Number of frames from near end of link aborted with underrun errors.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.13Counter64read-onlydeprecated
wanHssiStatsRxRingErrors
OBJECT-TYPE
Number of receive ring error events.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.14Counter64read-onlydeprecated
wanHssiStatsRxRingOverruns
OBJECT-TYPE
Number of receive ring overrun events.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.15Counter64read-onlydeprecated
wanHssiStatsTxRingErrors
OBJECT-TYPE
Number of transmit ring error events.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.16Counter64read-onlydeprecated
wanHssiStatsPortOpErrors
OBJECT-TYPE
Number of port operation error events.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.17Counter64read-onlydeprecated
wanHssiStatsTxCmplProcessings
OBJECT-TYPE
Number of transmit complete processings (TINT).
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.18Counter64read-onlydeprecated
wanHssiStatsOwner
OBJECT-TYPE
The entity that configured this entry.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.19OwnerStringread-createdeprecated
wanHssiStatsStatus
OBJECT-TYPE
The status of this wanHssiStatsTable entry.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.20RowStatusread-createdeprecated
wanT3E3StatsTable
OBJECT-TYPE
T3/E3 signaling statistics
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4not-accessiblecurrent
wanT3E3StatsEntry
OBJECT-TYPE
Statistics for a T3/E3 interface. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1not-accessiblecurrent
wanT3E3StatsIndex
OBJECT-TYPE
The value of this object uniquely identifies this wanT3E3StatsTable entry.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.1INTEGER (1..65535)not-accessiblecurrent
wanT3E3StatsDataSource
OBJECT-TYPE
This object identifies the source of the data that this wanT3E3StatsEntry analyzes. This source can be any DS3 or E3 interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in MIB-II [RFC 1573] for the desired interface. The ifType value of the associated ifIndex can only be ds3(30).
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.2OBJECT IDENTIFIERread-createcurrent
wanT3E3StatsDropEvents
OBJECT-TYPE
The total number of events in which frames were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of frames dropped; it is just the number of times this condition has been detected.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.3Counter64read-onlycurrent
wanT3E3StatsInFrames
OBJECT-TYPE
The total number of frames seen originating from the far end of the link including errored frames.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.4Counter64read-onlycurrent
wanT3E3StatsOutFrames
OBJECT-TYPE
The total number of frames seen originating from the near end of the link including errored frames.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.5Counter64read-onlycurrent
wanT3E3StatsInOctets
OBJECT-TYPE
The sum of octets from all frames seen originating from the far end of the link including errored frames.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.6Counter64read-onlycurrent
wanT3E3StatsOutOctets
OBJECT-TYPE
The sum of octets from all frames seen originating from the near end of the link including errored frames.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.7Counter64read-onlycurrent
wanT3E3StatsPESs
OBJECT-TYPE
A PES is a second with one or more PCVs OR one or more Out of Frame defects OR a detected incoming AIS. This gauge is not incremented when UASs are counted.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.8Counter64read-onlycurrent
wanT3E3StatsPSESs
OBJECT-TYPE
A PSES is a second with 44 or more PCVs OR one or more Out of Frame defects OR a detected incoming AIS. This gauge is not incremented when UASs are counted.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.9Counter64read-onlycurrent
wanT3E3StatsOOFs
OBJECT-TYPE
A DS3 OOF defect is detected when any three or more errors in sixteen or fewer consecutive F-bits occur within a DS3 M-frame. An OOF defect may also be called a Severely Errored Frame (SEF) defect. An OOF defect is cleared when reframe occurs. A DS3 Loss of Frame (LOF) failure is declared when the DS3 OOF defect is consistent for 2 to 10 seconds. The DS3 OOF defect ends when reframe occurs. The DS3 LOF failure is cleared when the DS3 OOF defect is absent for 10 to 20 seconds. An E3 OOF defect is detected when four consecutive frame alignment signals have been incorrectly received in there predicted positions in an E3 signal. E3 frame alignment occurs when the presence of three consecutive frame alignment signals have been detected.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.10Counter64read-onlycurrent
wanT3E3StatsSEFSs
OBJECT-TYPE
A SEFS is a second with one or more Out of Frame defects OR a detected incoming AIS.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.11Counter64read-onlycurrent
wanT3E3StatsUASs
OBJECT-TYPE
UAS are calculated by counting the number of seconds that the interface is unavailable. The DS3 interface is said to be unavailable from the onset of 10 contiguous PSESs, or the onset of the condition leading to a failure (see Failure States). If the condition leading to the failure was immediately preceded by one or more contiguous PSESs, then the DS3 interface unavailability starts from the onset of these PSESs. Once unavailable, and if no failure is present, the DS3 interface becomes available at the onset of 10 contiguous seconds with no PSESs. Once unavailable, and if a failure is present, the DS3 interface becomes available at the onset of 10 contiguous seconds with no PSESs, if the failure clearing time is less than or equal to 10 seconds. If the failure clearing time is more than 10 seconds, the DS3 interface becomes available at the onset of 10 contiguous seconds with no PSESs, or the onset period leading to the successful clearing condition, whichever occurs later. With respect to the DS3 error counts, all counters are incremented while the DS3 interface is deemed available. While the interface is deemed unavailable, the only count that is incremented is UASs.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.12Counter64read-onlycurrent
wanT3E3StatsLCVs
OBJECT-TYPE
This parameter is a count of both BPVs and EXZs occurring over the accumulation period. An EXZ increments the LCV by one regardless of the length of the zero string.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.13Counter64read-onlycurrent
wanT3E3StatsPCVs
OBJECT-TYPE
For all DS3 applications, a coding violation error event is a P-bit Parity Error event. A P-bit Parity Error event is the occurrence of a received P-bit code on the DS3 M-frame that is not identical to the corresponding locally- calculated code.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.14Counter64read-onlycurrent
wanT3E3StatsLESs
OBJECT-TYPE
A Line Errored Second is a second in which one or more CVs occurred OR one or more LOS defects.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.15Counter64read-onlycurrent
wanT3E3StatsCCVs
OBJECT-TYPE
For C-bit Parity and SYNTRAN DS3 applications, this is the count of coding violations reported via the C-bits. For C-bit Parity, it is a count of CP-bit parity errors occurring in the accumulation interval. For SYNTRAN, it is a count of CRC-9 errors occurring in the accumulation interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.16Counter64read-onlycurrent
wanT3E3StatsCESs
OBJECT-TYPE
An CES is a second with one or more CCVs OR one or more Out of Frame defects OR a detected incoming AIS. This count is only for the SYNTRAN and C-bit Parity DS3 applications. This gauge is not incremented when UASs are counted.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.17Counter64read-onlycurrent
wanT3E3StatsCSESs
OBJECT-TYPE
A CSES is a second with 44 or more CCVs OR one or more Out of Frame defects OR a detected incoming AIS. This count is only for the SYNTRAN and C-bit Parity DS3 applications. This gauge is not incremented when UASs are counted.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.18Counter64read-onlycurrent
wanT3E3StatsRAIs
OBJECT-TYPE
The Remote Alarm Indication (RAI) failure, in SYNTRAN applications, is declared after detecting the Yellow Alarm Signal on the alarm channel. See ANSI T1.107a-1990 [10]. The Remote Alarm Indication failure, in C-bit Parity DS3 applications, is declared as soon as the preqsence of either one or two alarm signals are detected on then Far End Alarm Channel. See [10]. The Remote Alarm Indication failure may also be declared after detecting the far-end SEF/AIS defect (aka yellow). The Remote Alarm Indication failure is cleared as soon as the presence of the any of the above alarms are removed. Also, the incoming failure state is declared when a defect persists for at least 2-10 seconds. The defects are the following: Loss of Signal (LOS), an Out of Frame (OOF) or an incoming Alarm Indication Signal (AIS). The Failure State is cleared when the defect is absent for less than or equal to 20 seconds.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.19Counter64read-onlycurrent
wanT3E3StatsAISs
OBJECT-TYPE
The DS3 AIS is framed with 'stuck stuffing.' This implies that it has a valid M-subframe alignments bits, M-frame alignment bits, and P bits. The information bits are set to a 1010... sequence, starting with a one (1) after each M-subframe alignment bit, M-frame alignment bit, X bit, P bit, and C bit. The C bits are all set to zero giving what is called 'stuck stuffing.' The X bits are set to one. The DS3 AIS defect is declared after DS3 AIS is present in contiguous M-frames for a time equal to or greater than T, where 0.2 ms <= T <= 100 ms. The DS3 AIS defect is terminated after AIS is absent in contiguous M-frames for a time equal to or greater than T. The E3 binary content of the AIS is nominally a continuous stream of ones. AIS detection and the application of consequent actions, should be completed within a time limit of 1 ms.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.20Counter64read-onlycurrent
wanT3E3StatsLOFs
OBJECT-TYPE
A DS3 Loss of Frame (LOF) failure is declared when the DS3 OOF defect is consistent for 2 to 10 seconds. The DS3 OOF defect ends when reframe occurs. The DS3 LOF failure is cleared when the DS3 OOF defect is absent for 10 to 20 seconds. (See T1.231 section 7.1.2.2.1)
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.21Counter64read-onlycurrent
wanT3E3StatsLOSs
OBJECT-TYPE
The DS3 LOS defect is declared upon observing 175 +/- 75 contiguous pulse positions with no pulses of either positive or negative polarity. The DS3 LOS defect is terminated upon observing an average pulse density of at least 33% over a period of 175 +/- 75 contiguous pulse positions starting with the receipt of a pulse.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.22Counter64read-onlycurrent
wanT3E3StatsOwner
OBJECT-TYPE
The entity that configured this entry.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.23OwnerStringread-createcurrent
wanT3E3StatsStatus
OBJECT-TYPE
The status of this wanT3E3StatsTable entry.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.24RowStatusread-createcurrent
wanAtmStatsTable
OBJECT-TYPE
ATM signaling statistics.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5not-accessiblecurrent
wanAtmStatsEntry
OBJECT-TYPE
The statistics for an ATM interface. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on. In an ATM network, there are many far ends of the link, but they shall be logically grouped into one end in this table.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1not-accessiblecurrent
wanAtmStatsIndex
OBJECT-TYPE
The value of this object uniquely identifies this wanAtmStatsTable entry.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.1INTEGER (1..65535)not-accessiblecurrent
wanAtmStatsDataSource
OBJECT-TYPE
This object identifies the source of the data that this wanAtmStatsEntry analyzes. This source can be any interface on this device. in order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in MIB-II [RFC 1573] for the desired interface. The ifType value associated with the ifIndex can only be atm(37).
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.2OBJECT IDENTIFIERread-createcurrent
wanAtmStatsDropEvents
OBJECT-TYPE
The total number of events in which frames were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of frames dropped; it is just the number of times this condition has been detected.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.3Counter64read-onlycurrent
wanAtmStatsInCells
OBJECT-TYPE
The total number of cells seen coming from the far end of the link including errored cells.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.4Counter64read-onlycurrent
wanAtmStatsOutCells
OBJECT-TYPE
The total number of cells seen coming from the near end of the link including errored cells.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.5Counter64read-onlycurrent
wanAtmStatsInCLP1
OBJECT-TYPE
The total number of cells with the CLP bit set seen coming from the far end of the link.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.6Counter64read-onlycurrent
wanAtmStatsOutCLP1
OBJECT-TYPE
The total number of cells with the CLP bit set seen coming from the near end of the link.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.7Counter64read-onlycurrent
wanAtmStatsConnectionEvents
OBJECT-TYPE
This counter counts the sum of the following errors: 1) SSCOP Connection Disconnect Counter The abnormal occurrence of this event is characterized by the expiry of Timer_NO_RESPONSE. (This event is communicated to the layer management with MAA-ERROR code P. See ITU-T Q.2110.) 2) SSCOP Connection Initiation Failure This condition indicates the inability to establish an SSCOP connection. This event occurs whenever the number of expiries of the connection control timer (Timer_CC) exceeds the MaxCC or upon receipt of a connection reject message BGREJ PDU. (This event is communicated to layer management with MAA-ERROR code O. See ITU-T Q.2110.) 3) SSCOP Connection Re-Establ/Resynch This event occurs upon receipt of a BGN PDU or RESYNC PDU.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.8Counter64read-onlycurrent
wanAtmStatsErroredPDUs
OBJECT-TYPE
This counter counts the sum of the following errors: 1) Invalid PDUs. These are defined in SSCOP and consist of PDUs with incorrect length (MAA-ERROR code U), undefined PDU type code or not 32-bit aligned. 2) PDUs that result in MAA error codes and are discarded See Errors A-M and Q-T defined in ITU-T Q.2110.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.9Counter64read-onlycurrent
wanAtmStatsSetupAttempts
OBJECT-TYPE
This counter counts the number of call setup attempts (both successful and unsuccessful) detected on this interface.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.10Counter64read-onlycurrent
wanAtmStatsInRoutesUnavailable
OBJECT-TYPE
This counter is incremented when a RELEASE, RELEASE COMPLETE (only when not preceded by a RELEASE mesg for the same call), ADD PARTY REJECT, or STATUS message that contains one of the following cause code values is received (Note: These cause values apply to both UNI3.0 and UNI3.1): Cause Value Meaning 1 unallocated (unassigned) number 2 no route to specified transit network 3 no route to destination 88 incompatible destination NOTE: For this counter, RELEASE COMPLETE messages that are a reply to a previous RELEASE message and contain the same cause value, are redundant (for counting purposes) and should not be counted.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.11Counter64read-onlycurrent
wanAtmStatsOutRoutesUnavailable
OBJECT-TYPE
This counter is incremented when a RELEASE, RELEASE COMPLETE (only when not preceded by a RELEASE mesg for the same call), ADD PARTY REJECT, or STATUS message that contains one of the following cause code values is transmitted (Note: These cause values apply to both UNI3.0 and UNI3.1): Cause Value Meaning 1 unallocated (unassigned) number 2 no route to specified transit network 3 no route to destination NOTE: For this counter, RELEASE COMPLETE messages that are a reply to a previous RELEASE message and contain the same cause value, are redundant(for counting purposes) and should not be counted.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.12Counter64read-onlycurrent
wanAtmStatsInResourcesUnavailable
OBJECT-TYPE
This counter is incremented when a RELEASE, RELEASE COMPLETE (only when not preceded by a RELEASE mesg for the same call), ADD PARTY REJECT, or STATUS message that contains one of the following cause code values is received (Note: These cause values apply to both UNI3.0 and UNI3.1 unless otherwise stated): Cause Value Meaning 35 requested VPCI/VCI not available 37 user cell rate not available (UNI3.1 only) 38 network out of order 41 temporary failure 45 no VPCI/VCI available 47 resource unavailable, unspecified 49 Quality of Service unavailable 51 user cell rate not available (UNI3.0 only) 58 bearer capability not presently available 63 Service or option not available, unspecified 92 too many pending add party requests NOTE: For this counter, RELEASE COMPLETE messages that are a reply to a previous RELEASE message and contain the same cause value, are redundant (for counting purposes) and should not be counted.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.13Counter64read-onlycurrent
wanAtmStatsOutResourcesUnavailable
OBJECT-TYPE
This counter is incremented when a RELEASE, RELEASE COMPLETE (only when not preceded by a RELEASE mesg for the same call), ADD PARTY REJECT, or STATUS message that contains one of the following cause code values is transmitted (Note: These cause values apply to both UNI3.0 and UNI3.1 unless otherwise stated): Cause Value Meaning 35 requested VPCI/VCI not available 37 user cell rate not available (UNI3.1 only) 38 network out of order 41 temporary failure 45 no VPCI/VCI available 47 resource unavailable, unspecified 49 Quality of Service unavailable 51 user cell rate not available (UNI3.0 only) 58 bearer capability not presently available 63 Service or option not available, unspecified 92 too many pending add party requests NOTE: For this counter, RELEASE COMPLETE messages that are a reply to a previous RELEASE message and contain the same cause value, are redundant (for counting purposes) and should not be counted.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.14Counter64read-onlycurrent
wanAtmStatsInUnsuccessfulCalls
OBJECT-TYPE
This counter is incremented when a RELEASE, RELEASE COMPLETE (only when not preceded by a RELEASE mesg for the same call), ADD PARTY REJECT, or STATUS message that contains one of the following cause code values is received (Note: These cause values apply to both UNI3.0 and UNI3.1): Cause Value Meaning 17 user busy 18 no user responding 21 call rejected 22 number changed 23 user rejects all calls with calling line id restriction 27 destination out of order 31 normal, unspecified 88 incompatible destination NOTE: For this counter, RELEASE COMPLETE messages that are a reply to a previous RELEASE message and contain the same cause value, are redundant (for counting purposes) and should not be counted. Note: Cause Value #30 'response to STATUS ENQUIRY' was not included in this memo since it did not apply to a hard failure.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.15Counter64read-onlycurrent
wanAtmStatsOutUnsuccessfulCalls
OBJECT-TYPE
This counter is incremented when a RELEASE, RELEASE COMPLETE (only when not preceded by a RELEASE mesg for the same call), ADD PARTY REJECT, or STATUS message that contains one of the following cause code values is transmitted (Note: These cause values apply to both UNI3.0 and UNI3.1): Cause Value Meaning 17 user busy 18 no user responding 21 call rejected 22 number changed 23 user rejects all calls with calling line id restriction (CLIR) 27 destination out of order 31 normal, unspecified 88 incompatible destination NOTE: For this counter, RELEASE COMPLETE messages that are a reply to a previous RELEASE message and contain the same cause value, are redundant(for counting purposes) and should not be counted. Note: Cause Value #30 'response to STATUS ENQUIRY' was not included in this memo since it did not apply to a hard failure.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.16Counter64read-onlycurrent
wanAtmStatsInIncorrectMsgs
OBJECT-TYPE
The Incorrect Messages Counter reflects any sort of incorrect information in a message. This includes: ? RELEASE, RELEASE COMPLETE, ADD PARTY REJECT, and STATUS messages transmitted or received, that contain any of the Cause values listed below. ? Ignored messages. These messages are dropped because the message was so damaged that it could not be further processed. A list of dropped messages is compiled below: Message with invalid protocol discriminator Message with errors in the call reference I.E. ? Bits 5-8 of the first octet not equal to '0000' ? Bits 1-4 of the first octet indicating a length other than 3 octets ? RELEASE COMPLETE message received with a call reference that does not relate to a call active or in progress ? SETUP message received with call reference flag incorrectly set to 1 ? SETUP message received with a call reference for a call that is already active or in progress. Message too short The following cause values are monitored by this counter (Note: These cause values apply to both UNI3.0 and UNI3.1 unless otherwise stated) Cause Value Meaning 10 VPCI/VCI unacceptable (UNI3.0 only) 36 VPCI/VCI assignment failure (UNI3.1 only) 81 invalid call reference value 82 identified channel does not exist 89 invalid endpoint reference 96 mandatory information element is missing 97 message type non-existent or not implemented 99 information element non-existent or not implemented 100 invalid information element contents 101 message not compatible with call state 104 incorrect message length 111 protocol error, unspecified NOTE: For this counter, RELEASE COMPLETE messages that are a reply to a previous RELEASE message and contain the same cause value, are redundant (for counting purposes) and should not be counted.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.17Counter64read-onlycurrent
wanAtmStatsOutIncorrectMsgs
OBJECT-TYPE
The Incorrect Messages Counter reflects any sort of incorrect information in a message. This includes: ? RELEASE, RELEASE COMPLETE, ADD PARTY REJECT, and STATUS messages transmitted or received, that contain any of the Cause values listed below. ? Ignored messages. These messages are dropped because the message was so damaged that it could not be further processed. A list of dropped messages is compiled below: Message with invalid protocol discriminator Message with errors in the call reference I.E. ? Bits 5-8 of the first octet not equal to '0000' ? Bits 1-4 of the first octet indicating a length other than 3 octets ? RELEASE COMPLETE message received with a call reference that does not relate to a call active or in progress ? SETUP message received with call reference flag incorrectly set to 1 ? SETUP message received with a call reference for a call that is already active or in progress. Message too short The following cause values are monitored by this counter Note: These cause values apply to both UNI3.0 and UNI3.1 unless otherwise stated) Cause Value Meaning 10 VPCI/VCI unacceptable (UNI3.0 only) 36 VPCI/VCI assignment failure (UNI3.1 only) 81 invalid call reference value 82 identified channel does not exist 89 invalid endpoint reference 96 mandatory information element is missing 97 message type non-existent or not implemented 99 information element non-existent or not implemented 100 invalid information element contents 101 message not compatible with call state 104 incorrect message length 111 protocol error, unspecified NOTE: For this counter, RELEASE COMPLETE messages that are a reply to a previous RELEASE message and contain the same cause value, are redundant (for counting purposes) and should not be counted.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.18Counter64read-onlycurrent
wanAtmStatsInPartyEvents
OBJECT-TYPE
This counter monitors error events that occur due to the originating user doing something wrong. This counter is incremented when a RELEASE, RELEASE COMPLETE (only when not preceded by a RELEASE mesg for the same call), ADD PARTY REJECT, or STATUS message that contains one of the following cause code values is received (Note: These cause values apply to both UNI3.0 and UNI3.1): Cause Value Meaning 28 invalid number format (address incomplete) 43 access information discarded 57 bearer capability not authorized 65 bearer capability not implemented 73 unsupported combination of traffic parameters 78 AAL parameters cannot be supported (UNI3.1 only) 91 invalid transit network selection 93 AAL parameters cannot be supported (UNI3.0 only) NOTE: For this counter, RELEASE COMPLETE messages that are a reply to a previous RELEASE message and contain the same cause value, are redundant(for counting purposes) and should not be counted.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.19Counter64read-onlycurrent
wanAtmStatsOutPartyEvents
OBJECT-TYPE
This counter monitors error events that occur due to the originating user doing something wrong. This counter is incremented when a RELEASE, RELEASE COMPLETE (only when not preceded by a RELEASE mesg for the same call), ADD PARTY REJECT, or STATUS message that contains one of the following cause code values is transmitted (Note: These cause values apply to both UNI3.0 and UNI3.1): Cause Value Meaning 28 invalid number format (address incomplete) 43 access information discarded 57 bearer capability not authorized 65 bearer capability not implemented 73 unsupported combination of traffic parameters 78 AAL parameters cannot be supported (UNI3.1 only) 91 invalid transit network selection 93 AAL parameters cannot be supported (UNI3.0 only) NOTE: For this counter, RELEASE COMPLETE messages that are a reply to a previous RELEASE message and contain the same cause value, are redundant (for counting purposes) and should not be counted.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.20Counter64read-onlycurrent
wanAtmStatsInExpiries
OBJECT-TYPE
The Timer Expiries Counter provides a count of network timer expiries, and to some extent, host or switch timer expiries. The conditions for incrementing this counter are: ? Expiry of any network timer ? Receipt of a RELEASE or RELEASE COMPLETE message with Cause #102, 'recovery on timer expiry'. NOTE: For this counter, RELEASE COMPLETE messages that are a reply to a previous RELEASE message and contain the same cause value, are redundant (for counting purposes) and should not be counted.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.21Counter64read-onlycurrent
wanAtmStatsOutExpiries
OBJECT-TYPE
The Timer Expiries Counter provides a count of network timer expiries, and to some extent, host or switch timer expiries. The conditions for incrementing this counter are: ? Expiry of any network timer ? Receipt of a RELEASE or RELEASE COMPLETE message with Cause #102, 'recovery on timer expiry'. NOTE: For this counter, RELEASE COMPLETE messages that are a reply to a previous RELEASE message and contain the same cause value, are redundant (for counting purposes) and should not be counted.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.22Counter64read-onlycurrent
wanAtmStatsInRestartErrors
OBJECT-TYPE
The Restart Activity Counter provides a count of host, switch, or network restart activity. This counter is incremented when receiving a RESTART message.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.23Counter64read-onlycurrent
wanAtmStatsOutRestartErrors
OBJECT-TYPE
The Restart Activity Counter provides a count of host, switch, or network restart activity. This counter is incremented when transmitting a RESTART message.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.24Counter64read-onlycurrent
wanAtmStatsInSVCs
OBJECT-TYPE
SVC VCCs established at this signaling entity for incoming connections.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.25Counter64read-onlycurrent
wanAtmStatsOutSVCs
OBJECT-TYPE
SVC VCCs established at this signaling entity for outgoing connections.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.26Counter64read-onlycurrent
wanAtmStatsInOCDs
OBJECT-TYPE
An out of cell delineation from far end of the link.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.27Counter64read-onlycurrent
wanAtmStatsOutOCDs
OBJECT-TYPE
An out of cell delineation from near end of the link.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.28Counter64read-onlycurrent
wanAtmStatsInLOCs
OBJECT-TYPE
A loss of cell delineation error from far end of the link. This is a persistent OCD condition.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.29Counter64read-onlycurrent
wanAtmStatsOutLOCs
OBJECT-TYPE
A loss of cell delineation error from near end of link. This is a persistent OCD condition.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.30Counter64read-onlycurrent
wanAtmStatsInLOFs
OBJECT-TYPE
A loss of frame error from far end of link.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.31Counter64read-onlycurrent
wanAtmStatsOutLOFs
OBJECT-TYPE
A loss of frame error from near end of link.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.32Counter64read-onlycurrent
wanAtmStatsInLOPs
OBJECT-TYPE
A loss of pointer error from far end of link.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.33Counter64read-onlycurrent
wanAtmStatsOutLOPs
OBJECT-TYPE
A loss of pointer error from near end of link.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.34Counter64read-onlycurrent
wanAtmStatsInLOSs
OBJECT-TYPE
A loss of signal error from far end of link.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.35Counter64read-onlycurrent
wanAtmStatsOutLOSs
OBJECT-TYPE
A loss of signal error from near end of link.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.36Counter64read-onlycurrent
wanAtmStatsOwner
OBJECT-TYPE
The entity that configured this entry.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.37OwnerStringread-createcurrent
wanAtmStatsStatus
OBJECT-TYPE
The status of this wanAtmStatsTable entry.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.38RowStatusread-createcurrent
wanProtocolStats
OBJECT-IDENTITY
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2
wanX25StatsTable
OBJECT-TYPE
X.25 Packet layer statistics.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1not-accessiblecurrent
wanX25StatsEntry
OBJECT-TYPE
The statistics for an X.25 interface across all LCIs. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on. In an X.25 network, there are many far ends of the link, but they shall be logically grouped into one end in this table.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1not-accessiblecurrent
wanX25StatsIndex
OBJECT-TYPE
The value of this object uniquely identifies this wanX25StatsTable entry.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.1INTEGER (1..65535)not-accessiblecurrent
wanX25StatsDataSource
OBJECT-TYPE
This object identifies the source of the data that this wanX25StatsEntry analyzes. This source can be any interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in MIB-II [RFC 1573] for the desired interface. The ifType value associated with the ifIndex can only be rfc887-x25(5).
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.2OBJECT IDENTIFIERread-createcurrent
wanX25StatsDropEvents
OBJECT-TYPE
The total number of events in which frames were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of frames dropped; it is just the number of times this condition has been detected.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.3Counter64read-onlycurrent
wanX25StatsInFrames
OBJECT-TYPE
The total number of frames seen coming from the far end of the link including error packets.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.4Counter64read-onlycurrent
wanX25StatsOutFrames
OBJECT-TYPE
The total number of frames seen coming from the near end of the link including error packets.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.5Counter64read-onlycurrent
wanX25StatsInOctets
OBJECT-TYPE
The sum of octets from all frames seen originating from the far end of the link including errored frames.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.6Counter64read-onlycurrent
wanX25StatsOutOctets
OBJECT-TYPE
The sum of octets from all frames seen originating from the near end of the link including errored frames.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.7Counter64read-onlycurrent
wanX25StatsInRejects
OBJECT-TYPE
The number of REJ or SREJ frames see coming from the far end of the link.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.8Counter64read-onlycurrent
wanX25StatsOutRejects
OBJECT-TYPE
The number of REJ or SREJ frames see coming from the near end of the link.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.9Counter64read-onlycurrent
wanX25StatsInAttempts
OBJECT-TYPE
The number of call setup attempts initiated from the far end of the link.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.10Counter64read-onlycurrent
wanX25StatsOutAttempts
OBJECT-TYPE
The number of call setup attempts initiated from the near end of the link.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.11Counter64read-onlycurrent
wanX25StatsInFailures
OBJECT-TYPE
The number call setup attempt failures seen coming from the far end of the link.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.12Counter64read-onlycurrent
wanX25StatsOutFailures
OBJECT-TYPE
The number call setup attempt failures seen coming from the near end of the link.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.13Counter64read-onlycurrent
wanX25StatsProviderClears
OBJECT-TYPE
The number of clear request seen with a cause code other than DTE initiated.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.14Counter64read-onlycurrent
wanX25StatsInResets
OBJECT-TYPE
The number of reset requests seen from the far end of the link with cause code DTE initiated.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.15Counter64read-onlycurrent
wanX25StatsOutResets
OBJECT-TYPE
The number of reset requests seen from the near end of the link with cause code DTE initiated.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.16Counter64read-onlycurrent
wanX25StatsProviderResets
OBJECT-TYPE
The number of reset requests seen with cause code other than DTE initiated.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.17Counter64read-onlycurrent
wanX25StatsInAccusedErrors
OBJECT-TYPE
The numbers of packets seen from the far end of the link containing a procedure error cause code. These include clear, reset, restart, or diagnostic packets.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.18Counter64read-onlycurrent
wanX25StatsOutAccusedErrors
OBJECT-TYPE
The numbers of packets seen from the near end of the link containing a procedure error cause code. These include clear, reset, restart, or diagnostic packets.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.19Counter64read-onlycurrent
wanX25StatsInInterrupts
OBJECT-TYPE
The number of interrupts packets seen coming from the far end of the link over all VCs.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.20Counter64read-onlycurrent
wanX25StatsOutInterrupts
OBJECT-TYPE
The number of interrupts packets seen coming from the near end of the link over all VCs.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.21Counter64read-onlycurrent
wanX25StatsOwner
OBJECT-TYPE
The entity that configured this entry.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.22OwnerStringread-createcurrent
wanX25StatsStatus
OBJECT-TYPE
The status of this wanX25StatsTable entry.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.23RowStatusread-createcurrent
wanFrStatsTable
OBJECT-TYPE
Frame Relay statistics.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2not-accessiblecurrent
wanFrStatsEntry
OBJECT-TYPE
The statistics for a frame relay interface across all DLCIs. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on. In a frame relay network, there are many far ends of the link, but they shall be logically grouped into one end in this table.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1not-accessiblecurrent
wanFrStatsIndex
OBJECT-TYPE
The value of this object uniquely identifies this wanFrStatsTable entry.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.1INTEGER (1..65535)not-accessiblecurrent
wanFrStatsDataSource
OBJECT-TYPE
This object identifies the source of the data that this wanFrStatsEntry analyzes. This source can be any frame relay interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in MIB-II [RFC 1573] for the desired interface. The ifType value associated with the ifIndex can only be frameRelay(32).
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.2OBJECT IDENTIFIERread-createcurrent
wanFrStatsDropEvents
OBJECT-TYPE
The total number of events in which frames were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of frames dropped; it is just the number of times this condition has been detected.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.3Counter64read-onlycurrent
wanFrStatsInFrames
OBJECT-TYPE
The total number of frames seen coming from the far end of the link including error packets.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.4Counter64read-onlycurrent
wanFrStatsOutFrames
OBJECT-TYPE
The total number of frames seen coming from the near end of the link including error packets.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.5Counter64read-onlycurrent
wanFrStatsInOctets
OBJECT-TYPE
The sum of octets from all frames seen originating from the far end of the link including errored frames.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.6Counter64read-onlycurrent
wanFrStatsOutOctets
OBJECT-TYPE
The sum of octets from all frames seen originating from the near end of the link including errored frames.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.7Counter64read-onlycurrent
wanFrStatsInFECNs
OBJECT-TYPE
The number of frames see coming form the far end of the link with the FECN bit set.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.8Counter64read-onlycurrent
wanFrStatsOutFECNs
OBJECT-TYPE
The number of frames see coming form the near end of the link with the FECN bit set.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.9Counter64read-onlycurrent
wanFrStatsInBECNs
OBJECT-TYPE
The number of frames seen coming from the far end of the link with the BECN bit set.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.10Counter64read-onlycurrent
wanFrStatsOutBECNs
OBJECT-TYPE
The number of frames seen coming from the near end of the link with the BECN bit set.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.11Counter64read-onlycurrent
wanFrStatsInDEs
OBJECT-TYPE
The number of frames seen coming from the far end of the link with the DE bit set.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.12Counter64read-onlycurrent
wanFrStatsOutDEs
OBJECT-TYPE
The number of frames seen coming from the near end of the link with the DE bit set.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.13Counter64read-onlycurrent
wanFrStatsOwner
OBJECT-TYPE
The entity that configured this entry.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.14OwnerStringread-createcurrent
wanFrStatsStatus
OBJECT-TYPE
The status of this wanFrStatsTable entry.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.15RowStatusread-createcurrent
wanAal5StatsTable
OBJECT-TYPE
AAL/5 statistics.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3not-accessiblecurrent
wanAal5StatsEntry
OBJECT-TYPE
The statistics for a AAL/5 interface. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on. In an ATM network, there are many far ends of the link, but they shall be logically grouped into one end in this table.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1not-accessiblecurrent
wanAal5StatsIndex
OBJECT-TYPE
The value of this object uniquely identifies this wanAal5StatsTable entry.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.1INTEGER (1..65535)not-accessiblecurrent
wanAal5StatsDataSource
OBJECT-TYPE
This object identifies the source of the data that this wanAal5StatsEntry analyzes. This source can be any interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in MIB-II [RFC 1573] for the desired interface. The ifType value associated with the ifIndex can only be aal5(49).
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.2OBJECT IDENTIFIERread-createcurrent
wanAal5StatsDropEvents
OBJECT-TYPE
The total number of events in which frames were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of frames dropped; it is just the number of times this condition has been detected.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.3Counter64read-onlycurrent
wanAal5StatsInCells
OBJECT-TYPE
The total number of cells for any AAL-5 connection seen coming from the far end of the link.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.4Counter64read-onlycurrent
wanAal5StatsOutCells
OBJECT-TYPE
The total number of cells for any AAL-5 connection seen coming from the near end of the link.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.5Counter64read-onlycurrent
wanAal5StatsInPDUs
OBJECT-TYPE
The total number of AAL-5 PDUs seen coming from the far end of the link including error PDUs.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.6Counter64read-onlycurrent
wanAal5StatsOutPDUs
OBJECT-TYPE
The total number of AAL-5 PDUs seen coming from the near end of the link including error PDUs.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.7Counter64read-onlycurrent
wanAal5StatsInOctets
OBJECT-TYPE
The sum of octets from all AAL-5 PDUs seen originating from the far end of the link including errored PDUs.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.8Counter64read-onlycurrent
wanAal5StatsOutOctets
OBJECT-TYPE
The sum of octets from all AAL-5 PDUs seen originating from the near end of the link including errored PDUs.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.9Counter64read-onlycurrent
wanAal5StatsInCLP1
OBJECT-TYPE
The total number of cells for any AAL-5 connection with the CLP bit set seen coming from the far end of the link.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.10Counter64read-onlycurrent
wanAal5StatsOutCLP1
OBJECT-TYPE
The total number of cells for any AAL-5 connection with the CLP bit set seen coming from the near end of the link.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.11Counter64read-onlycurrent
wanAal5StatsInCRCs
OBJECT-TYPE
The total number of AAL-5 PDUs with CRC errors from the far end of the link.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.12Counter64read-onlycurrent
wanAal5StatsOutCRCs
OBJECT-TYPE
The total number of AAL-5 PDUs with CRC errors from the near end of the link.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.13Counter64read-onlycurrent
wanAal5StatsInOversizedSDUs
OBJECT-TYPE
The total number of AAL-5 SDUs from the far end of the link that were too large.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.14Counter64read-onlycurrent
wanAal5StatsOutOversizedSDUs
OBJECT-TYPE
The total number of AAL-5 SDUs from the near end of the link that were too large.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.15Counter64read-onlycurrent
wanAal5StatsInSVCs
OBJECT-TYPE
The total number of AAL/5 connections seen initiated from the far end of the link.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.16Counter64read-onlycurrent
wanAal5StatsOutSVCs
OBJECT-TYPE
The total number of AAL-5 connections seen initiated from the near end of the link.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.17Counter64read-onlycurrent
wanAal5StatsOwner
OBJECT-TYPE
The entity that configured this entry.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.18OwnerStringread-createcurrent
wanAal5StatsStatus
OBJECT-TYPE
The status of this wanAal5StatsTable entry.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.19RowStatusread-createcurrent
wanPppStatsTable
OBJECT-TYPE
PPP in HDLC service statistics.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4not-accessiblecurrent
wanPppStatsEntry
OBJECT-TYPE
The statistics for a PPP in HDLC service. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1not-accessiblecurrent
wanPppStatsIndex
OBJECT-TYPE
The value of this object uniquely identifies this wanPppStatsTable entry.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.1INTEGER (1..65535)not-accessiblecurrent
wanPppStatsDataSource
OBJECT-TYPE
This object identifies the source of the data that this wanPppStatsEntry analyzes. This source can be any interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in MIB-II [RFC 1573] for the desired interface. The ifType value associated with the ifIndex can only be ppp(22).
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.2OBJECT IDENTIFIERread-createcurrent
wanPppStatsDropEvents
OBJECT-TYPE
The total number of events in which frames were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of frames dropped; it is just the number of times this condition has been detected.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.3Counter64read-onlycurrent
wanPppStatsInFrames
OBJECT-TYPE
The total number of frames seen coming from the far end of the link including error frames.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.4Counter64read-onlycurrent
wanPppStatsOutFrames
OBJECT-TYPE
The total number of frames seen coming from the near end of the link including error frames.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.5Counter64read-onlycurrent
wanPppStatsInOctets
OBJECT-TYPE
The sum of octets from all frames seen coming from the far end of the link including errored frames.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.6Counter64read-onlycurrent
wanPppStatsOutOctets
OBJECT-TYPE
The sum of octets from all frames seen coming from the near end of the link including errored frames.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.7Counter64read-onlycurrent
wanPppStatsInBadAddresses
OBJECT-TYPE
The number of frames seen from the far end of the link with an incorrect address field.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.8Counter64read-onlycurrent
wanPppStatsOutBadAddresses
OBJECT-TYPE
The number of frames seen from the near end of the link with an incorrect address field
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.9Counter64read-onlycurrent
wanPppStatsInBadControls
OBJECT-TYPE
The number of frames seen from the far end of the link with an incorrect control field.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.10Counter64read-onlycurrent
wanPppStatsOutBadControls
OBJECT-TYPE
The number of frames seen from the near end of the link with an incorrect control field.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.11Counter64read-onlycurrent
wanPppStatsInLongFrames
OBJECT-TYPE
The number of frames seen from the far end of the link that exceed the MRU.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.12Counter64read-onlycurrent
wanPppStatsOutLongFrames
OBJECT-TYPE
The number of frames seen from the near end of the link that exceed the MRU.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.13Counter64read-onlycurrent
wanPppStatsInBadFCSs
OBJECT-TYPE
The number of packets seen from the far end of the link with incorrect FCSs.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.14Counter64read-onlycurrent
wanPppStatsOutBadFCSs
OBJECT-TYPE
The number of packets seen from the near end of the link with incorrect FCSs.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.15Counter64read-onlycurrent
wanPppStatsOwner
OBJECT-TYPE
The entity that configured this entry.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.16OwnerStringread-createcurrent
wanPppStatsStatus
OBJECT-TYPE
The status of this wanPppStatsTable entry.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.17RowStatusread-createcurrent
wanPvcStats
OBJECT-IDENTITY
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3
wanX25PvcStatsTable
OBJECT-TYPE
X.25 per-LCI statistics for a PVC.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1not-accessiblecurrent
wanX25PvcStatsEntry
OBJECT-TYPE
The statistics for a X.25 PVC. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the sides the probe is not on.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1not-accessiblecurrent
wanX25PvcStatsIndex
OBJECT-TYPE
The value of this object uniquely identifies this wanX25PvcStatsTable entry.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.1INTEGER (1..65535)not-accessiblecurrent
wanX25PvcStatsDataSource
OBJECT-TYPE
This object identifies the source of the data that this wanX25PvcStatsEntry analyzes. This source can be any pvcEntry associated with an X.25 interface. In order to identify a particular LCI to monitor, this object shall identify the instance of the pvcIndex object that corresponds to a X.25 PVC, defined above for the desired interface.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.2OBJECT IDENTIFIERread-createcurrent
wanX25PvcStatsDropEvents
OBJECT-TYPE
The total number of events in which frames were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of frames dropped; it is just the number of times this condition has been detected.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.3Counter64read-onlycurrent
wanX25PvcStatsInFrames
OBJECT-TYPE
The total number of frames seen coming from the far end of the link on this LCI.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.4Counter64read-onlycurrent
wanX25PvcStatsOutFrames
OBJECT-TYPE
The total number of frames seen coming from the near end of the link on this LCI.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.5Counter64read-onlycurrent
wanX25PvcStatsInOctets
OBJECT-TYPE
The sum of octets from all frames seen originating from the far end of the link on this LCI.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.6Counter64read-onlycurrent
wanX25PvcStatsOutOctets
OBJECT-TYPE
The sum of octets from all frames seen originating from the near end of the link on this LCI.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.7Counter64read-onlycurrent
wanX25PvcStatsInResets
OBJECT-TYPE
The number of reset requests seen from the far end of the link with cause code DTE initiated for this LCI.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.8Counter64read-onlycurrent
wanX25PvcStatsOutResets
OBJECT-TYPE
The number of reset requests seen from the far end of the link with cause code DTE initiated for this LCI.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.9Counter64read-onlycurrent
wanX25PvcStatsProviderResets
OBJECT-TYPE
The number of reset requests seen with cause code other than DTE initiated for this LCI.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.10Counter64read-onlycurrent
wanX25PvcStatsInAccusedErrors
OBJECT-TYPE
The numbers of frames seen from the far end of the link containing a procedure error cause code on this LCI. These include clear, reset, restart, or diagnostic packets.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.11Counter64read-onlycurrent
wanX25PvcStatsOutAccusedErrors
OBJECT-TYPE
The numbers of frames seen from the near end of the link containing a procedure error cause code on this LCI. These include clear, reset, restart, or diagnostic packets.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.12Counter64read-onlycurrent
wanX25PvcStatsInInterrupts
OBJECT-TYPE
The number of interrupts frames seen coming from the far end of the link on this LCI.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.13Counter64read-onlycurrent
wanX25PvcStatsOutInterrupts
OBJECT-TYPE
The number of interrupts frames seen coming from the far end of the link on this LCI.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.14Counter64read-onlycurrent
wanX25PvcStatsUpTime
OBJECT-TYPE
The total amount of time in one-hundreds of a second that the probe is sure this LCI was active, i.e., the total time the value of wanX25PvcStatsState was equal to up(1). A value of less than the age of this entry does not necessarily mean that this LCI was down. It only means the probe was not certain it was up. Note: the sum of wanX25PvcStatsUpTime and wanX25PvcStatsDownTime may be less than the age of this entry. In this case, the unaccounted for time is the time the probe was uncertain of the state of this LCI, i.e., the total time the value of wanX25PvcStatsState was unknown(3).
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.15TimeTicksread-onlycurrent
wanX25PvcStatsDownTime
OBJECT-TYPE
The total amount of time in one-hundreds of a second that the probe is sure this LCI was down, i.e., the total time the value of wanX25PvcStatsState was equal to down(3). A value of less than the age of this entry does not necessarily mean that this LCI was up at some point. It only means the probe was not certain it was down. Note: the sum of wanX25PvcStatsUpTime and wanX25PvcStatsDownTime may be less than the age of this entry. In this case, the unaccounted for time is the time the probe was uncertain of the state of this LCI, i.e., the total time the value of wanX25PvcStatsState was unknown(3).
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.16TimeTicksread-onlycurrent
wanX25PvcStatsState
OBJECT-TYPE
The current state of this LCI as inferred by the probe. A value of up(2) means the LCI is active. A value of down(2) means the LCI is inactive. And a value of unknown(3) means the probe cannot currently infer the state.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.17INTEGER {up(1), down(2), unknown(3)}read-onlycurrent
wanX25PvcStatsStateChanges
OBJECT-TYPE
The count of the number of times the wanX25PvcStatsState has gone from up(1) to down(2) or vice versa. The number of times wanX25PvcStatsState goes to unknown(3) is not counted. However, if the value goes from up(1) to unknown(3) and then to down(2) should be counted as 1. Likewise going from down(2) to unknown(3) and then to up(3) should be counted as 1.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.18Counter64read-onlycurrent
wanX25PvcStatsOwner
OBJECT-TYPE
The entity that configured this entry.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.19OwnerStringread-createcurrent
wanX25PvcStatsStatus
OBJECT-TYPE
The status of this wanX25PvcStatsTable entry.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.20RowStatusread-createcurrent
wanFrPvcStatsTable
OBJECT-TYPE
Frame Relay per-DLCI statistics.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2not-accessiblecurrent
wanFrPvcStatsEntry
OBJECT-TYPE
The statistics for a frame relay DLCI. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1not-accessiblecurrent
wanFrPvcStatsIndex
OBJECT-TYPE
The value of this object uniquely identifies this wanFrPvcStatsTable entry.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.1INTEGER (1..65535)not-accessiblecurrent
wanFrPvcStatsDataSource
OBJECT-TYPE
This object identifies the source of the data that this wanFrPvcStatsEntry analyzes. This source can be any pvcEntry associated with a frame relay interface on this device. In order to identify a particular DLCI, this object shall identify the instance of the frame relay pvcIndex object, defined in the PVCCONFIG-MIB.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.2OBJECT IDENTIFIERread-createcurrent
wanFrPvcStatsDropEvents
OBJECT-TYPE
The total number of events in which frames were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of frames dropped; it is just the number of times this condition has been detected.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.3Counter64read-onlycurrent
wanFrPvcStatsInFrames
OBJECT-TYPE
The total number of frames seen coming from the far end of the link on this DLCI.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.4Counter64read-onlycurrent
wanFrPvcStatsOutFrames
OBJECT-TYPE
The total number of frames seen coming from the near end of the link on this DLCI.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.5Counter64read-onlycurrent
wanFrPvcStatsInOctets
OBJECT-TYPE
The sum of octets from all frames seen originating from the far end of the link on this DLCI.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.6Counter64read-onlycurrent
wanFrPvcStatsOutOctets
OBJECT-TYPE
The sum of octets from all frames seen originating from the near end of the link on this DLCI.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.7Counter64read-onlycurrent
wanFrPvcStatsInFECNs
OBJECT-TYPE
The number of frames see coming form the far end of the link with the FECN bit set on this DLCI.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.8Counter64read-onlycurrent
wanFrPvcStatsOutFECNs
OBJECT-TYPE
The number of frames seen coming from the far end of the link with the BECN bit set on this DLCI.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.9Counter64read-onlycurrent
wanFrPvcStatsInBECNs
OBJECT-TYPE
The number of frames see coming form the near end of the link with the FECN bit set.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.10Counter64read-onlycurrent
wanFrPvcStatsOutBECNs
OBJECT-TYPE
The number of frames seen coming from the near end of the link with the BECN bit set on this DLCI.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.11Counter64read-onlycurrent
wanFrPvcStatsInDEs
OBJECT-TYPE
The number of frames seen coming from the far end of the link with the DE bit set on this DCLI.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.12Counter64read-onlycurrent
wanFrPvcStatsOutDEs
OBJECT-TYPE
The number of frames seen coming from the near end of the link with the DE bit set on this DLCI.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.13Counter64read-onlycurrent
wanFrPvcStatsUpTime
OBJECT-TYPE
The total amount of time in one-hundreds of a second that the probe is sure this LCI was active, i.e., the total time the value of wanFrPvcStatsState was equal to up(1). A value of less than the age of this entry does not necessarily mean that this LCI was down. It only means the probe was not certain it was up. Note: the sum of wanFrPvcStatsUpTime and wanFrPvcStatsDownTime may be less than the age of this entry. In this case, the unaccounted for time is the time the probe was uncertain of the state of this DLCI, i.e., the total time the value of wanFrPvcStatsState was unknown(3).
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.14TimeTicksread-onlycurrent
wanFrPvcStatsDownTime
OBJECT-TYPE
The total amount of time in one-hundreds of a second that the probe is sure this LCI was down, i.e., the total time the value of wanFrPvcStatsState was equal to down(3). A value of less than the age of this entry does not necessarily mean that this LCI was up at some point. It only means the probe was not certain it was down. Note: the sum of wanX25PvcStatsUpTime and wanFrPvcStatsDownTime may be less than the age of this entry. In this case, the unaccounted for time is the time the probe was uncertain of the state of this DLCI, i.e., the total time the value of wanFrPvcStatsState was unknown(3).
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.15TimeTicksread-onlycurrent
wanFrPvcStatsState
OBJECT-TYPE
The current state of this DLCI as inferred by the probe. A value of up(2) means the DLCI is active. A value of down(2) means the DLCI is inactive. And a value of unknown(3) means the probe cannot currently infer the state.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.16INTEGER {up(1), down(2), unknown(3)}read-onlycurrent
wanFrPvcStatsStateChanges
OBJECT-TYPE
The count of the number of times the wanFrPvcStatsState has gone from up(1) to down(2) or vice versa. The number of times wanFrPvcStatsState goes to unknown(3) is not counted. However, if the value goes from up(1) to unknown(3) and then to down(2) should be counted as 1. Likewise going from down(2) to unknown(3) and then to up(3) should be counted as 1.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.17Counter64read-onlycurrent
wanFrPvcStatsOwner
OBJECT-TYPE
The entity that configured this entry.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.18OwnerStringread-createcurrent
wanFrPvcStatsStatus
OBJECT-TYPE
The status of this wanFrPvcStatsTable entry.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.19RowStatusread-createcurrent
wanAal5PvcStatsTable
OBJECT-TYPE
AAL/5 per-VPI/VCI statistics.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3not-accessiblecurrent
wanAal5PvcStatsEntry
OBJECT-TYPE
The statistics for a AAL-5 VCI/VPI. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1not-accessiblecurrent
wanAal5PvcStatsIndex
OBJECT-TYPE
The value of this object uniquely identifies this wanAal5PvcStatsTable entry.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.1INTEGER (1..65535)not-accessiblecurrent
wanAal5PvcStatsDataSource
OBJECT-TYPE
This object identifies the source of the data that this wanAal5StatsEntry analyzes. This source can be any pvcEntry that is associated with an ATM interface on this device. In order to identify a particular VPI/VCI, this object shall identify the instance of the pvcIndex object, defined in the PVCCONFIG-MIB.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.2OBJECT IDENTIFIERread-createcurrent
wanAal5PvcStatsDropEvents
OBJECT-TYPE
The total number of events in which frames were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of frames dropped; it is just the number of times this condition has been detected.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.3Counter64read-onlycurrent
wanAal5PvcStatsInCells
OBJECT-TYPE
The total number of cells for seen coming from the far end of the link on this VPI/VCI.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.4Counter64read-onlycurrent
wanAal5PvcStatsOutCells
OBJECT-TYPE
The total number of cells seen coming from the near end of the link on this VPI/VCI.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.5Counter64read-onlycurrent
wanAal5PvcStatsInPDUs
OBJECT-TYPE
The total number of AAL-5 PDUs seen coming from the far end of the link on this VPI/VCI.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.6Counter64read-onlycurrent
wanAal5PvcStatsOutPDUs
OBJECT-TYPE
The total number of AAL-5 PDUs seen coming from the near end of the link on this VPI/VCI.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.7Counter64read-onlycurrent
wanAal5PvcStatsInOctets
OBJECT-TYPE
The sum of octets from all AAL-5 PDUs seen originating from the far end of the link on this VCI/VPI.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.8Counter64read-onlycurrent
wanAal5PvcStatsOutOctets
OBJECT-TYPE
The sum of octets from all AAL-5 PDUs seen originating from the near end of the link on this VPI/VCI.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.9Counter64read-onlycurrent
wanAal5PvcStatsInCLP1
OBJECT-TYPE
The total number of cells with the CLP bit set seen coming from the far end of the link on this VCI/VPI.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.10Counter64read-onlycurrent
wanAal5PvcStatsOutCLP1
OBJECT-TYPE
The total number of cells with the CLP bit set seen coming from the near end of the link on this VCI/VPI.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.11Counter64read-onlycurrent
wanAal5PvcStatsInCRCs
OBJECT-TYPE
The total number of AAL-5 PDUs with CRC errors seen coming from the far end of the link on this VCI/VPI.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.12Counter64read-onlycurrent
wanAal5PvcStatsOutCRCs
OBJECT-TYPE
The total number of AAL-5 PDUs with CRC errors seen coming from the near end of the link on this VPI/VCI.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.13Counter64read-onlycurrent
wanAal5PvcStatsInOversizedSDUs
OBJECT-TYPE
The number of AAL5 SDUs from the far end of the link that were too large on this VPI/VCI.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.14Counter64read-onlycurrent
wanAal5PvcStatsOutOversizedSDUs
OBJECT-TYPE
The number of AAL5 SDUs from the near end of the link that were too large on this VPI/VCI.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.15Counter64read-onlycurrent
wanAal5PvcStatsUpTime
OBJECT-TYPE
The total amount of time in one-hundreds of a second that the probe is sure this LCI was active, i.e., the total time the value of wanAal5PvcStatsState was equal to up(1). A value of less than the age of this entry does not necessarily mean that this VPI/VCI was down. It only means the probe was not certain it was up. Note: the sum of wanAal5PvcStatsUpTime and wanAal5PvcStatsDownTime may be less than the age of this entry. In this case, the unaccounted for time is the time the probe was uncertain of the state of this VPI/VCI, i.e., the total time the value of wanAal5PvcStatsState was unknown(3).
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.16TimeTicksread-onlycurrent
wanAal5PvcStatsDownTime
OBJECT-TYPE
The total amount of time in one-hundreds of a second that the probe is sure this LCI was down, i.e., the total time the value of wanAal5PvcStatsState was equal to down(3). A value of less than the age of this entry does not necessarily mean that this VPI/VCI was up at some point. It only means the probe was not certain it was down. Note: the sum of wanAal5PvcStatsUpTime and wanAal5PvcStatsDownTime may be less than the age of this entry. In this case, the unaccounted for time is the time the probe was uncertain of the state of this VPI/VCI, i.e., the total time the value of wanAal5PvcStatsState was unknown(3).
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.17TimeTicksread-onlycurrent
wanAal5PvcStatsState
OBJECT-TYPE
The current state of this VPI/VCI as inferred by the probe. A value of up(2) means the LCI is active. A value of down(2) means the VPI/VCI is inactive. And a value of unknown(3) means the probe cannot currently infer the state.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.18INTEGER {up(1), down(2), unknown(3)}read-onlycurrent
wanAal5PvcStatsStateChanges
OBJECT-TYPE
The count of the number of times the wanAal5PvcStatsState has gone from up(1) to down(2) or vice versa. The number of times wanAal5PvcStatsState goes to unknown(3) is not counted. However, if the value goes from up(1) to unknown(3) and then to down(2) should be counted as 1. Likewise going from down(2) to unknown(3) and then to up(3) should be counted as 1.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.19Counter64read-onlycurrent
wanAal5PvcStatsOwner
OBJECT-TYPE
The entity that configured this entry.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.20OwnerStringread-createcurrent
wanAal5PvcStatsStatus
OBJECT-TYPE
The status of this wanAal5PvcStatsTable entry.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.21RowStatusread-createcurrent
wanHistoryMIBObjects
OBJECT-IDENTITY
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2
wanSignalingHistory
OBJECT-IDENTITY
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1
wanT1E1HistoryTable
OBJECT-TYPE
T1/E1 signaling statistics.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1not-accessiblecurrent
wanT1E1HistoryEntry
OBJECT-TYPE
Statistics for a particular T1/E1 interface. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1not-accessiblecurrent
wanT1E1HistoryIndex
OBJECT-TYPE
The history of which this entry is a port. The history identified by a particular value of this index is the same history as identified by the same value of historyControlIndex.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.1INTEGER (1..65535)not-accessiblecurrent
wanT1E1HistorySampleIndex
OBJECT-TYPE
An index that uniquely identifies the particular sample this entry represents among all samples associated with the same historyControlEntry. This index starts at 1 and increases by one as each new sample is taken.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.2INTEGER (1..2147483647)not-accessiblecurrent
wanT1E1HistoryIntervalStart
OBJECT-TYPE
The value of sysUpTime at the start of the interval over which this sample was measured. If the probe keeps track of time of day, it should start the first sample of the history at a time such that when the next hour of the day begins, a sample is started at that instant. Note that following this rule may require the probe to delay collection the first sample of the history, as each sample must be of the same interval. Also note that the sample which is currently being collected is not accessible in this table until the end of its interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.3TimeTicksread-onlycurrent
wanT1E1HistoryDropEvents
OBJECT-TYPE
The change in value of wanT1E1StatsDropEvents during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.4Counter64read-onlycurrent
wanT1E1HistoryInFrames
OBJECT-TYPE
The change in value of wanT1E1StatsInFrames during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.5Counter64read-onlycurrent
wanT1E1HistoryOutFrames
OBJECT-TYPE
The change in value of wanT1E1StatsOutFrames during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.6Counter64read-onlycurrent
wanT1E1HistoryInOctets
OBJECT-TYPE
The change in value of wanT1E1StatsInOctets during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.7Counter64read-onlycurrent
wanT1E1HistoryOutOctets
OBJECT-TYPE
The change in value of wanT1E1StatsOutOctets during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.8Counter64read-onlycurrent
wanT1E1HistoryESs
OBJECT-TYPE
The change in value of wanT1E1StatsESs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.9Counter64read-onlycurrent
wanT1E1HistorySESs
OBJECT-TYPE
The change in value of wanT1E1StatsSESs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.10Counter64read-onlycurrent
wanT1E1HistorySEFSs
OBJECT-TYPE
The change in value of wanT1E1StatsSEFSs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.11Counter64read-onlycurrent
wanT1E1HistoryOOFs
OBJECT-TYPE
The change in value of wanT1E1StatsOOFs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.12Counter64read-onlycurrent
wanT1E1HistoryUASs
OBJECT-TYPE
The change in value of wanT1E1StatsUASs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.13Counter64read-onlycurrent
wanT1E1HistoryCSSs
OBJECT-TYPE
The change in value of wanT1E1StatsCSSs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.14Counter64read-onlycurrent
wanT1E1HistoryPCVs
OBJECT-TYPE
The change in value of wanT1E1StatsPCVs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.15Counter64read-onlycurrent
wanT1E1HistoryLESs
OBJECT-TYPE
The change in value of wanT1E1StatsLESs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.16Counter64read-onlycurrent
wanT1E1HistoryBESs
OBJECT-TYPE
The change in value of wanT1E1StatsBESs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.17Counter64read-onlycurrent
wanT1E1HistoryDMs
OBJECT-TYPE
The change in value of wanT1E1StatsDMs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.18Counter64read-onlycurrent
wanT1E1HistoryLCVs
OBJECT-TYPE
The change in value of wanT1E1StatsLCVs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.19Counter64read-onlycurrent
wanT1E1HistoryLOFs
OBJECT-TYPE
The change in value of wanT1E1StatsLOFSs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.20Counter64read-onlycurrent
wanT1E1HistoryLOSs
OBJECT-TYPE
The change in value of wanT1E1StatsLOSs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.21Counter64read-onlycurrent
wanT1E1HistoryRAIs
OBJECT-TYPE
The change in value of wanT1E1StatsRAIs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.22Counter64read-onlycurrent
wanT1E1HistoryAISs
OBJECT-TYPE
The change in value of wanT1E1StatsAISs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.23Counter64read-onlycurrent
wanT1E1HistoryTS16AISs
OBJECT-TYPE
The change in value of wanT1E1StatsTS16AISs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.24Counter64read-onlycurrent
wanT1E1HistoryLOMFs
OBJECT-TYPE
The change in value of wanT1E1StatsLOMFs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.25Counter64read-onlycurrent
wanT1E1HistoryFarLOMFs
OBJECT-TYPE
The change in value of wanT1E1StatsFarLOMFs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.26Counter64read-onlycurrent
wanT1E1HistoryInUtilization
OBJECT-TYPE
The best estimated of the mean physical layer network utilization of traffic coming from the far end of the link in hundreds of a percent.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.27INTEGER (0..10000)read-onlycurrent
wanT1E1HistoryOutUtilization
OBJECT-TYPE
The best estimated of the mean physical layer network utilization of traffic coming from the near end of the link in hundreds of a percent.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.28INTEGER (0..10000)read-onlycurrent
wanVSeriesHistoryTable
OBJECT-TYPE
The history of which this entry is a port. The history identified by a particular value of this index is the same history as identified by the same value of historyControlIndex.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2not-accessiblecurrent
wanVSeriesHistoryEntry
OBJECT-TYPE
The statistics for a V-series interface. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1not-accessiblecurrent
wanVSeriesHistoryIndex
OBJECT-TYPE
The history of which this entry is a port. The history identified by a particular value of this index is the same history as identified by the same value of historyControlIndex.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.1INTEGER (1..65535)not-accessiblecurrent
wanVSeriesHistorySampleIndex
OBJECT-TYPE
An index that uniquely identifies the particular sample this entry represents among all samples associated with the same historyControlEntry. This index starts at 1 and increases by one as each new sample is taken.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.2INTEGER (1..2147483647)not-accessiblecurrent
wanVSeriesHistoryIntervalStart
OBJECT-TYPE
The value of sysUpTime at the start of the interval over which this sample was measured. If the probe keeps track of time of day, it should start the first sample of the history at a time such that when the next hour of the day begins, a sample is started at that instant. Note that following this rule may require the probe to delay collection the first sample of the history, as each sample must be of the same interval. Also note that the sample which is currently being collected is not accessible in this table until the end of its interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.3TimeTicksread-onlycurrent
wanVSeriesHistoryDropEvents
OBJECT-TYPE
The change in value of wanVSeriesStatsDropEvents during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.4Counter64read-onlycurrent
wanVSeriesHistoryInFrames
OBJECT-TYPE
The change in value of wanVSeriesStatsInFrames during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.5Counter64read-onlycurrent
wanVSeriesHistoryOutFrames
OBJECT-TYPE
The change in value of wanVSeriesStatsOutFrames during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.6Counter64read-onlycurrent
wanVSeriesHistoryInOctets
OBJECT-TYPE
The change in value of wanVSeriesStatsInOctets during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.7Counter64read-onlycurrent
wanVSeriesHistoryOutOctets
OBJECT-TYPE
The change in value of wanVSeriesStatsOutOctets during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.8Counter64read-onlycurrent
wanVSeriesHistoryInFCSs
OBJECT-TYPE
The change in value of wanVSeriesStatsInFCSs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.9Counter64read-onlycurrent
wanVSeriesHistoryOutFCSs
OBJECT-TYPE
The change in value of wanVSeriesStatsOutFCSs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.10Counter64read-onlycurrent
wanVSeriesHistoryInOverruns
OBJECT-TYPE
The change in value of wanVSeriesStatsInOverruns during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.11Counter64read-onlycurrent
wanVSeriesHistoryOutOverruns
OBJECT-TYPE
The change in value of wanVSeriesStatsOutOverruns during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.12Counter64read-onlycurrent
wanVSeriesHistoryInterruptedFrames
OBJECT-TYPE
The change in value of wanVSeriesStatsInterruptedFrames during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.13Counter64read-onlycurrent
wanVSeriesHistoryInAbortedFrames
OBJECT-TYPE
The change in value of wanVSeriesStatsInAbortedFrames during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.14Counter64read-onlycurrent
wanVSeriesHistoryOutAbortedFrames
OBJECT-TYPE
The change in value of wanVSeriesStatsOutAbortedFrames during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.15Counter64read-onlycurrent
wanVSeriesHistoryInUtilization
OBJECT-TYPE
The best estimated of the mean physical layer network utilization of traffic coming from the far end of the link in hundreds of a percent.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.16INTEGER (0..10000)read-onlycurrent
wanVSeriesHistoryOutUtilization
OBJECT-TYPE
The best estimated of the mean physical layer network utilization of traffic coming from the near end of the link in hundreds of a percent.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.17INTEGER (0..10000)read-onlycurrent
wanHssiHistoryTable
OBJECT-TYPE
HSSI interface statistics.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3not-accessibledeprecated
wanHssiHistoryEntry
OBJECT-TYPE
The statistics for a HSSI interface. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1not-accessibledeprecated
wanHssiHistoryIndex
OBJECT-TYPE
The history of which this entry is a port. The history identified by a particular value of this index is the same history as identified by the same value of historyControlIndex.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.1INTEGER (1..65535)not-accessibledeprecated
wanHssiHistorySampleIndex
OBJECT-TYPE
An index that uniquely identifies the particular sample this entry represents among all samples associated with the same historyControlEntry. This index starts at 1 and increases by one as each new sample is taken.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.2INTEGER (1..2147483647)not-accessibledeprecated
wanHssiHistoryIntervalStart
OBJECT-TYPE
The value of sysUpTime at the start of the interval over which this sample was measured. If the probe keeps track of time of day, it should start the first sample of the history at a time such that when the next hour of the day begins, a sample is started at that instant. Note that following this rule may require the probe to delay collection the first sample of the history, as each sample must be of the same interval. Also note that the sample which is currently being collected is not accessible in this table until the end of its interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.3TimeTicksread-onlydeprecated
wanHssiHistoryDropEvents
OBJECT-TYPE
The change in value of wanHssiStatsDropEvents during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.4Counter64read-onlydeprecated
wanHssiHistoryInFrames
OBJECT-TYPE
The change in value of wanHssiStatsInFrames during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.5Counter64read-onlydeprecated
wanHssiHistoryOutFrames
OBJECT-TYPE
The change in value of wanHssiStatsOutFrames during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.6Counter64read-onlydeprecated
wanHssiHistoryInOctets
OBJECT-TYPE
The change in value of wanHssiStatsInOctets during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.7Counter64read-onlydeprecated
wanHssiHistoryOutOctets
OBJECT-TYPE
The change in value of wanHssiStatsOutOctets during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.8Counter64read-onlydeprecated
wanHssiHistoryRxLongFrames
OBJECT-TYPE
The change in value of wanHssiStatsRxLongFrames during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.9Counter64read-onlydeprecated
wanHssiHistoryRxCrcErrors
OBJECT-TYPE
The change in value of wanHssiStatsRxCrcErrors during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.10Counter64read-onlydeprecated
wanHssiHistoryRxOverruns
OBJECT-TYPE
The change in value of wanHssiStatsRxOverruns during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.11Counter64read-onlydeprecated
wanHssiHistoryRxAborts
OBJECT-TYPE
The change in value of wanHssiStatsRxAborts during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.12Counter64read-onlydeprecated
wanHssiHistoryTxAborts
OBJECT-TYPE
The change in value of wanHssiStatsTxAborts during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.13Counter64read-onlydeprecated
wanHssiHistoryTxUnderruns
OBJECT-TYPE
The change in value of wanHssiStatsTxUnderruns during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.14Counter64read-onlydeprecated
wanHssiHistoryRxRingErrors
OBJECT-TYPE
The change in value of wanHssiStatsTxRingErrors during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.15Counter64read-onlydeprecated
wanHssiHistoryRxRingOverruns
OBJECT-TYPE
The change in value of wanHssiStatsRxRingOverruns during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.16Counter64read-onlydeprecated
wanHssiHistoryTxRingErrors
OBJECT-TYPE
The change in value of wanHssiStatsTxRingErrors during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.17Counter64read-onlydeprecated
wanHssiHistoryPortOpErrors
OBJECT-TYPE
The change in value of wanHssiStatsPortOpErrors during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.18Counter64read-onlydeprecated
wanHssiHistoryTxCmplProcessings
OBJECT-TYPE
The change in value of wanHssiStatsTxCmplProcessings during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.19Counter64read-onlydeprecated
wanHssiHistoryInUtilization
OBJECT-TYPE
The best estimated of the mean physical layer network utilization of traffic coming from the far end of the link in hundreds of a percent.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.20INTEGER (0..10000)read-onlydeprecated
wanHssiHistoryOutUtilization
OBJECT-TYPE
The best estimated of the mean physical layer network utilization of traffic coming from the near end of the link in hundreds of a percent.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.21INTEGER (0..10000)read-onlydeprecated
wanT3E3HistoryTable
OBJECT-TYPE
T3/E3 signaling statistics
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4not-accessiblecurrent
wanT3E3HistoryEntry
OBJECT-TYPE
Statistics for a T3/E3 interface. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1not-accessiblecurrent
wanT3E3HistoryIndex
OBJECT-TYPE
The history of which this entry is a port. The history identified by a particular value of this index is the same history as identified by the same value of historyControlIndex.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.1INTEGER (1..65535)not-accessiblecurrent
wanT3E3HistorySampleIndex
OBJECT-TYPE
An index that uniquely identifies the particular sample this entry represents among all samples associated with the same historyControlEntry. This index starts at 1 and increases by one as each new sample is taken.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.2INTEGER (1..2147483647)not-accessiblecurrent
wanT3E3HistoryIntervalStart
OBJECT-TYPE
The value of sysUpTime at the start of the interval over which this sample was measured. If the probe keeps track of time of day, it should start the first sample of the history at a time such that when the next hour of the day begins, a sample is started at that instant. Note that following this rule may require the probe to delay collection the first sample of the history, as each sample must be of the same interval. Also note that the sample which is currently being collected is not accessible in this table until the end of its interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.3TimeTicksread-onlycurrent
wanT3E3HistoryDropEvents
OBJECT-TYPE
The change in value of wanT3E3StatsDropEvents during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.4Counter64read-onlycurrent
wanT3E3HistoryInFrames
OBJECT-TYPE
The change in value of wanT3E3StatsInFrames during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.5Counter64read-onlycurrent
wanT3E3HistoryOutFrames
OBJECT-TYPE
The change in value of wanT3E3StatsOutFrames during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.6Counter64read-onlycurrent
wanT3E3HistoryInOctets
OBJECT-TYPE
The change in value of wanT3E3StatsInOctets during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.7Counter64read-onlycurrent
wanT3E3HistoryOutOctets
OBJECT-TYPE
The change in value of wanT3E3StatsOutOctets during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.8Counter64read-onlycurrent
wanT3E3HistoryPESs
OBJECT-TYPE
The change in value of wanT3E3StatsPESs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.9Counter64read-onlycurrent
wanT3E3HistoryPSESs
OBJECT-TYPE
The change in value of wanT3E3StatsPSESs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.10Counter64read-onlycurrent
wanT3E3HistoryOOFs
OBJECT-TYPE
The change in value of wanT3E3StatsOOFs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.11Counter64read-onlycurrent
wanT3E3HistorySEFSs
OBJECT-TYPE
The change in value of wanT3E3StatsSEFs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.12Counter64read-onlycurrent
wanT3E3HistoryUASs
OBJECT-TYPE
The change in value of wanT3E3StatsUASs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.13Counter64read-onlycurrent
wanT3E3HistoryLCVs
OBJECT-TYPE
The change in value of wanT3E3StatsLCVs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.14Counter64read-onlycurrent
wanT3E3HistoryPCVs
OBJECT-TYPE
The change in value of wanT3E3StatsPCVs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.15Counter64read-onlycurrent
wanT3E3HistoryLESs
OBJECT-TYPE
The change in value of wanT3E3StatsLESs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.16Counter64read-onlycurrent
wanT3E3HistoryCCVs
OBJECT-TYPE
The change in value of wanT3E3StatsCCVs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.17Counter64read-onlycurrent
wanT3E3HistoryCESs
OBJECT-TYPE
The change in value of wanT3E3StatsCESs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.18Counter64read-onlycurrent
wanT3E3HistoryCSESs
OBJECT-TYPE
The change in value of wanT3E3StatsCSESs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.19Counter64read-onlycurrent
wanT3E3HistoryRAIs
OBJECT-TYPE
The change in value of wanT3E3StatsRAIs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.20Counter64read-onlycurrent
wanT3E3HistoryAISs
OBJECT-TYPE
The change in value of wanT3E3StatsAISs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.21Counter64read-onlycurrent
wanT3E3HistoryLOFs
OBJECT-TYPE
The change in value of wanT3E3StatsLOFs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.22Counter64read-onlycurrent
wanT3E3HistoryLOSs
OBJECT-TYPE
The change in value of wanT3E3StatsLOSs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.23Counter64read-onlycurrent
wanT3E3HistoryInUtilization
OBJECT-TYPE
The best estimated of the mean physical layer network utilization of traffic coming from the far end of the link in hundreds of a percent.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.24INTEGER (0..10000)read-onlycurrent
wanT3E3HistoryOutUtilization
OBJECT-TYPE
The best estimated of the mean physical layer network utilization of traffic coming from the near end of the link in hundreds of a percent.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.25INTEGER (0..10000)read-onlycurrent
wanAtmHistoryTable
OBJECT-TYPE
ATM signaling statistics.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5not-accessiblecurrent
wanAtmHistoryEntry
OBJECT-TYPE
The statistics for an ATM interface. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on. In an ATM network, there are many far ends of the link, but they shall be logically grouped into one end in this table.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1not-accessiblecurrent
wanAtmHistoryIndex
OBJECT-TYPE
The history of which this entry is a port. The history identified by a particular value of this index is the same history as identified by the same value of historyControlIndex.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.1INTEGER (1..65535)not-accessiblecurrent
wanAtmHistorySampleIndex
OBJECT-TYPE
An index that uniquely identifies the particular sample this entry represents among all samples associated with the same historyControlEntry. This index starts at 1 and increases by one as each new sample is taken.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.2INTEGER (1..2147483647)not-accessiblecurrent
wanAtmHistoryIntervalStart
OBJECT-TYPE
The value of sysUpTime at the start of the interval over which this sample was measured. If the probe keeps track of time of day, it should start the first sample of the history at a time such that when the next hour of the day begins, a sample is started at that instant. Note that following this rule may require the probe to delay collection the first sample of the history, as each sample must be of the same interval. Also note that the sample which is currently being collected is not accessible in this table until the end of its interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.3TimeTicksread-onlycurrent
wanAtmHistoryDropEvents
OBJECT-TYPE
The change in value of wanAtmStatsDropEvents during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.4Counter64read-onlycurrent
wanAtmHistoryInCells
OBJECT-TYPE
The change in value of wanAtmStatsInCells during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.5Counter64read-onlycurrent
wanAtmHistoryOutCells
OBJECT-TYPE
The change in value of wanAtmStatsOutCells during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.6Counter64read-onlycurrent
wanAtmHistoryInCLP1
OBJECT-TYPE
The change in value of wanAtmStatsInCLP1 during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.7Counter64read-onlycurrent
wanAtmHistoryOutCLP1
OBJECT-TYPE
The change in value of wanAtmStatsOutCLP1 during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.8Counter64read-onlycurrent
wanAtmHistoryConnectionEvents
OBJECT-TYPE
The change in value of wanAtmStatsConnectionEvents during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.9Counter64read-onlycurrent
wanAtmHistoryErroredPDUs
OBJECT-TYPE
The change in value of wanAtmStatsErroredPDUs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.10Counter64read-onlycurrent
wanAtmHistorySetupAttempts
OBJECT-TYPE
The change in value of wanAtmStatsSetupAttempts during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.11Counter64read-onlycurrent
wanAtmHistoryInRoutesUnavailable
OBJECT-TYPE
The change in value of wanAtmStatsInRoutesUnavailable during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.12Counter64read-onlycurrent
wanAtmHistoryOutRoutesUnavailable
OBJECT-TYPE
The change in value of wanAtmStatsOutRoutesUnavailable during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.13Counter64read-onlycurrent
wanAtmHistoryInResourcesUnavailable
OBJECT-TYPE
The change in value of wanAtmStatsInResourcesUnavailable during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.14Counter64read-onlycurrent
wanAtmHistoryOutResourcesUnavailable
OBJECT-TYPE
The change in value of wanAtmStatsOutResourcesUnavailable during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.15Counter64read-onlycurrent
wanAtmHistoryInUnsuccessfulCalls
OBJECT-TYPE
The change in value of wanAtmStatsInUnsuccessfulCalls during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.16Counter64read-onlycurrent
wanAtmHistoryOutUnsuccessfulCalls
OBJECT-TYPE
The change in value of wanAtmStatsOutUnsuccessfulCalls during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.17Counter64read-onlycurrent
wanAtmHistoryInIncorrectMsgs
OBJECT-TYPE
The change in value of wanAtmStatsInIncorrectMsgs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.18Counter64read-onlycurrent
wanAtmHistoryOutIncorrectMsgs
OBJECT-TYPE
The change in value of wanAtmStatsOutIncorrectMsgs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.19Counter64read-onlycurrent
wanAtmHistoryInPartyEvents
OBJECT-TYPE
The change in value of wanAtmStatsInPartyEvents during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.20Counter64read-onlycurrent
wanAtmHistoryOutPartyEvents
OBJECT-TYPE
The change in value of wanAtmStatsOutPartyEvents during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.21Counter64read-onlycurrent
wanAtmHistoryInExpiries
OBJECT-TYPE
The change in value of wanAtmStatsInExpiries during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.22Counter64read-onlycurrent
wanAtmHistoryOutExpiries
OBJECT-TYPE
The change in value of wanAtmStatsOutExpiries during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.23Counter64read-onlycurrent
wanAtmHistoryInRestartErrors
OBJECT-TYPE
The change in value of wanAtmStatsInRestartErrors during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.24Counter64read-onlycurrent
wanAtmHistoryOutRestartErrors
OBJECT-TYPE
The change in value of wanAtmStatsOutRestartErrors during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.25Counter64read-onlycurrent
wanAtmHistoryInSVCs
OBJECT-TYPE
The change in value of wanAtmStatsInSVCs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.26Counter64read-onlycurrent
wanAtmHistoryOutSVCs
OBJECT-TYPE
The change in value of wanAtmStatsOutSVCs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.27Counter64read-onlycurrent
wanAtmHistoryInOCDs
OBJECT-TYPE
The change in value of wanAtmStatsInOCDs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.28Counter64read-onlycurrent
wanAtmHistoryOutOCDs
OBJECT-TYPE
The change in value of wanAtmStatsOutOCDs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.29Counter64read-onlycurrent
wanAtmHistoryInLOCs
OBJECT-TYPE
The change in value of wanAtmStatsInLOCs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.30Counter64read-onlycurrent
wanAtmHistoryOutLOCs
OBJECT-TYPE
The change in value of wanAtmStatsOutLOCs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.31Counter64read-onlycurrent
wanAtmHistoryInLOFs
OBJECT-TYPE
The change in value of wanAtmStatsInLOFs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.32Counter64read-onlycurrent
wanAtmHistoryOutLOFs
OBJECT-TYPE
The change in value of wanAtmStatsOutLOFs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.33Counter64read-onlycurrent
wanAtmHistoryInLOPs
OBJECT-TYPE
The change in value of wanAtmStatsInLOPs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.34Counter64read-onlycurrent
wanAtmHistoryOutLOPs
OBJECT-TYPE
The change in value of wanAtmStatsOutLOPs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.35Counter64read-onlycurrent
wanAtmHistoryInLOSs
OBJECT-TYPE
The change in value of wanAtmStatsInLOSs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.36Counter64read-onlycurrent
wanAtmHistoryOutLOSs
OBJECT-TYPE
The change in value of wanAtmStatsOutLOSs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.37Counter64read-onlycurrent
wanAtmHistoryInUtilization
OBJECT-TYPE
The best estimated of the mean physical layer network utilization of traffic coming from the far end of the link in hundreds of a percent.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.38INTEGER (0..10000)read-onlycurrent
wanAtmHistoryOutUtilization
OBJECT-TYPE
The best estimated of the mean physical layer network utilization of traffic coming from the near end of the link in hundreds of a percent.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.39INTEGER (0..10000)read-onlycurrent
wanProtocolHistory
OBJECT-IDENTITY
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2
wanX25HistoryTable
OBJECT-TYPE
X.25 Packet layer statistics.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1not-accessiblecurrent
wanX25HistoryEntry
OBJECT-TYPE
The statistics for an X.25 interface across all LCIs. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on. In a X.25 network, there are many far ends of the link, but they shall be logically grouped into one end in this table.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1not-accessiblecurrent
wanX25HistoryIndex
OBJECT-TYPE
The history of which this entry is a port. The history identified by a particular value of this index is the same history as identified by the same value of historyControlIndex.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.1INTEGER (1..65535)not-accessiblecurrent
wanX25HistorySampleIndex
OBJECT-TYPE
An index that uniquely identifies the particular sample this entry represents among all samples associated with the same historyControlEntry. This index starts at 1 and increases by one as each new sample is taken.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.2INTEGER (1..2147483647)not-accessiblecurrent
wanX25HistoryIntervalStart
OBJECT-TYPE
The value of sysUpTime at the start of the interval over which this sample was measured. If the probe keeps track of time of day, it should start the first sample of the history at a time such that when the next hour of the day begins, a sample is started at that instant. Note that following this rule may require the probe to delay collection the first sample of the history, as each sample must be of the same interval. Also note that the sample which is currently being collected is not accessible in this table until the end of its interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.3TimeTicksread-onlycurrent
wanX25HistoryDropEvents
OBJECT-TYPE
The change in value of wanX25StatsDropEvents during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.4Counter64read-onlycurrent
wanX25HistoryInFrames
OBJECT-TYPE
The change in value of wanX25StatsInFrames during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.5Counter64read-onlycurrent
wanX25HistoryOutFrames
OBJECT-TYPE
The change in value of wanX25StatsOutFrames during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.6Counter64read-onlycurrent
wanX25HistoryInOctets
OBJECT-TYPE
The change in value of wanX25StatsInOctets during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.7Counter64read-onlycurrent
wanX25HistoryOutOctets
OBJECT-TYPE
The change in value of wanX25StatsOutOctets during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.8Counter64read-onlycurrent
wanX25HistoryInRejects
OBJECT-TYPE
The change in value of wanX25StatsInRejects during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.9Counter64read-onlycurrent
wanX25HistoryOutRejects
OBJECT-TYPE
The change in value of wanX25StatsOutRejects during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.10Counter64read-onlycurrent
wanX25HistoryInAttempts
OBJECT-TYPE
The change in value of wanX25StatsInAttempts during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.11Counter64read-onlycurrent
wanX25HistoryOutAttempts
OBJECT-TYPE
The change in value of wanX25StatsOutAttempts during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.12Counter64read-onlycurrent
wanX25HistoryInFailures
OBJECT-TYPE
The change in value of wanX25StatsInFailures during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.13Counter64read-onlycurrent
wanX25HistoryOutFailures
OBJECT-TYPE
The change in value of wanX25StatsOutFailures during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.14Counter64read-onlycurrent
wanX25HistoryProviderClears
OBJECT-TYPE
The change in value of wanX25StatsProviderClears during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.15Counter64read-onlycurrent
wanX25HistoryInResets
OBJECT-TYPE
The change in value of wanX25StatsInResets during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.16Counter64read-onlycurrent
wanX25HistoryOutResets
OBJECT-TYPE
The change in value of wanX25StatsOutResets during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.17Counter64read-onlycurrent
wanX25HistoryProviderResets
OBJECT-TYPE
The change in value of wanX25StatsProviderResets during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.18Counter64read-onlycurrent
wanX25HistoryInAccusedErrors
OBJECT-TYPE
The change in value of wanX25StatsInAccusedErrors during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.19Counter64read-onlycurrent
wanX25HistoryOutAccusedErrors
OBJECT-TYPE
The change in value of wanX25StatsOutAccusedErrors during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.20Counter64read-onlycurrent
wanX25HistoryInInterrupts
OBJECT-TYPE
The change in value of wanX25StatsInInterrupts during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.21Counter64read-onlycurrent
wanX25HistoryOutInterrupts
OBJECT-TYPE
The change in value of wanX25StatsOutInterrupts during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.22Counter64read-onlycurrent
wanX25HistoryInUtilization
OBJECT-TYPE
The best estimated of the mean physical layer network utilization of traffic coming from the far end of the link in hundreds of a percent.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.23INTEGER (0..10000)read-onlycurrent
wanX25HistoryOutUtilization
OBJECT-TYPE
The best estimated of the mean physical layer network utilization of traffic coming from the near end of the link in hundreds of a percent.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.24INTEGER (0..10000)read-onlycurrent
wanFrHistoryTable
OBJECT-TYPE
Frame Relay statistics.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2not-accessiblecurrent
wanFrHistoryEntry
OBJECT-TYPE
The statistics for a frame relay interface across all DLCIs. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on. In a frame relay network, there are many far ends of the link, but they shall be logically grouped into one end in this table.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1not-accessiblecurrent
wanFrHistoryIndex
OBJECT-TYPE
The history of which this entry is a port. The history identified by a particular value of this index is the same history as identified by the same value of historyControlIndex.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.1INTEGER (1..65535)not-accessiblecurrent
wanFrHistorySampleIndex
OBJECT-TYPE
An index that uniquely identifies the particular sample this entry represents among all samples associated with the same historyControlEntry. This index starts at 1 and increases by one as each new sample is taken.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.2INTEGER (1..2147483647)not-accessiblecurrent
wanFrHistoryIntervalStart
OBJECT-TYPE
The value of sysUpTime at the start of the interval over which this sample was measured. If the probe keeps track of time of day, it should start the first sample of the history at a time such that when the next hour of the day begins, a sample is started at that instant. Note that following this rule may require the probe to delay collection the first sample of the history, as each sample must be of the same interval. Also note that the sample which is currently being collected is not accessible in this table until the end of its interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.3TimeTicksread-onlycurrent
wanFrHistoryDropEvents
OBJECT-TYPE
The change in value of wanFrStatsDropEvents during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.4Counter64read-onlycurrent
wanFrHistoryInFrames
OBJECT-TYPE
The change in value of wanFrStatsInFrames during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.5Counter64read-onlycurrent
wanFrHistoryOutFrames
OBJECT-TYPE
The change in value of wanFrStatsOutFrames during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.6Counter64read-onlycurrent
wanFrHistoryInOctets
OBJECT-TYPE
The change in value of wanFrStatsInOctets during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.7Counter64read-onlycurrent
wanFrHistoryOutOctets
OBJECT-TYPE
The change in value of wanFrStatsOutOctets during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.8Counter64read-onlycurrent
wanFrHistoryInFECNs
OBJECT-TYPE
The change in value of wanFrStatsInFECSs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.9Counter64read-onlycurrent
wanFrHistoryOutFECNs
OBJECT-TYPE
The change in value of wanFrStatsOutFECNs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.10Counter64read-onlycurrent
wanFrHistoryInBECNs
OBJECT-TYPE
The change in value of wanFrStatsInBECNs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.11Counter64read-onlycurrent
wanFrHistoryOutBECNs
OBJECT-TYPE
The change in value of wanFrStatsOutBECNs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.12Counter64read-onlycurrent
wanFrHistoryInDEs
OBJECT-TYPE
The change in value of wanFrStatsInDEs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.13Counter64read-onlycurrent
wanFrHistoryOutDEs
OBJECT-TYPE
The change in value of wanFrStatsDOutDEs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.14Counter64read-onlycurrent
wanFrHistoryInUtilization
OBJECT-TYPE
The best estimated of the mean physical layer network utilization of traffic coming from the far end of the link in hundreds of a percent.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.15INTEGER (0..10000)read-onlycurrent
wanFrHistoryOutUtilization
OBJECT-TYPE
The best estimated of the mean physical layer network utilization of traffic coming from the near end of the link in hundreds of a percent.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.16INTEGER (0..10000)read-onlycurrent
wanAal5HistoryTable
OBJECT-TYPE
AAL/5 statistics.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3not-accessiblecurrent
wanAal5HistoryEntry
OBJECT-TYPE
The statistics for a AAL/5 interface. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on. In an ATM network, there are many far ends of the link, but they shall be logically grouped into one end in this table.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1not-accessiblecurrent
wanAal5HistoryIndex
OBJECT-TYPE
The history of which this entry is a port. The history identified by a particular value of this index is the same history as identified by the same value of historyControlIndex.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.1INTEGER (1..65535)not-accessiblecurrent
wanAal5HistorySampleIndex
OBJECT-TYPE
An index that uniquely identifies the particular sample this entry represents among all samples associated with the same historyControlEntry. This index starts at 1 and increases by one as each new sample is taken.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.2INTEGER (1..2147483647)not-accessiblecurrent
wanAal5HistoryIntervalStart
OBJECT-TYPE
The value of sysUpTime at the start of the interval over which this sample was measured. If the probe keeps track of time of day, it should start the first sample of the history at a time such that when the next hour of the day begins, a sample is started at that instant. Note that following this rule may require the probe to delay collection the first sample of the history, as each sample must be of the same interval. Also note that the sample which is currently being collected is not accessible in this table until the end of its interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.3TimeTicksread-onlycurrent
wanAal5HistoryDropEvents
OBJECT-TYPE
The change in value of wanAal5StatsDropEvents during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.4Counter64read-onlycurrent
wanAal5HistoryInCells
OBJECT-TYPE
The change in value of wanAal5StatsInCells during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.5Counter64read-onlycurrent
wanAal5HistoryOutCells
OBJECT-TYPE
The change in value of wanAal5StatsOutCells during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.6Counter64read-onlycurrent
wanAal5HistoryInPDUs
OBJECT-TYPE
The change in value of wanAal5StatsInPDUs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.7Counter64read-onlycurrent
wanAal5HistoryOutPDUs
OBJECT-TYPE
The change in value of wanAal5StatsOutPDUs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.8Counter64read-onlycurrent
wanAal5HistoryInOctets
OBJECT-TYPE
The change in value of wanAal5StatsInOctets during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.9Counter64read-onlycurrent
wanAal5HistoryOutOctets
OBJECT-TYPE
The change in value of wanAal5StatsOutOctets during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.10Counter64read-onlycurrent
wanAal5HistoryInCLP1
OBJECT-TYPE
The change in value of wanAal5StatsInCLP1 the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.11Counter64read-onlycurrent
wanAal5HistoryOutCLP1
OBJECT-TYPE
The change in value of wanAal5StatsOutCLP1 during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.12Counter64read-onlycurrent
wanAal5HistoryInCRCs
OBJECT-TYPE
The change in value of wanAal5StatsInCRCs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.13Counter64read-onlycurrent
wanAal5HistoryOutCRCs
OBJECT-TYPE
The change in value of wanAal5StatsOutCRCs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.14Counter64read-onlycurrent
wanAal5HistoryInOversizedSDUs
OBJECT-TYPE
The change in value of wanAal5StatsInOversizedSDUs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.15Counter64read-onlycurrent
wanAal5HistoryOutOversizedSDUs
OBJECT-TYPE
The change in value of wanAal5StatsOutOversizedSDUs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.16Counter64read-onlycurrent
wanAal5HistoryInSVCs
OBJECT-TYPE
The change in value of wanAal5StatsInSVCs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.17Counter64read-onlycurrent
wanAal5HistoryOutSVCs
OBJECT-TYPE
The change in value of wanAal5StatsOutSVCs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.18Counter64read-onlycurrent
wanAal5HistoryInUtilization
OBJECT-TYPE
The best estimated of the mean AAL-5 layer network utilization of traffic coming from the far end of the link in hundreds of a percent.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.19INTEGER (0..10000)read-onlycurrent
wanAal5HistoryOutUtilization
OBJECT-TYPE
The best estimated of the mean AAL-5 layer network utilization of traffic coming from the near end of the link in hundreds of a percent.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.20INTEGER (0..10000)read-onlycurrent
wanPppHistoryTable
OBJECT-TYPE
PPP in HDLC service statistics.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4not-accessiblecurrent
wanPppHistoryEntry
OBJECT-TYPE
The statistics for a PPP in HDLC service. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1not-accessiblecurrent
wanPppHistoryIndex
OBJECT-TYPE
The history of which this entry is a port. The history identified by a particular value of this index is the same history as identified by the same value of historyControlIndex.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.1INTEGER (1..65535)not-accessiblecurrent
wanPppHistorySampleIndex
OBJECT-TYPE
An index that uniquely identifies the particular sample this entry represents among all samples associated with the same historyControlEntry. This index starts at 1 and increases by one as each new sample is taken.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.2INTEGER (1..2147483647)not-accessiblecurrent
wanPppHistoryIntervalStart
OBJECT-TYPE
The value of sysUpTime at the start of the interval over which this sample was measured. If the probe keeps track of time of day, it should start the first sample of the history at a time such that when the next hour of the day begins, a sample is started at that instant. Note that following this rule may require the probe to delay collection the first sample of the history, as each sample must be of the same interval. Also note that the sample which is currently being collected is not accessible in this table until the end of its interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.3TimeTicksread-onlycurrent
wanPppHistoryDropEvents
OBJECT-TYPE
The change in value of wanPppStatsDropEvents during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.4Counter64read-onlycurrent
wanPppHistoryInFrames
OBJECT-TYPE
The change in value of wanPppStatsInFrames during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.5Counter64read-onlycurrent
wanPppHistoryOutFrames
OBJECT-TYPE
The change in value of wanPppStatsOutFrames during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.6Counter64read-onlycurrent
wanPppHistoryInOctets
OBJECT-TYPE
The change in value of wanPppStatsInOctets during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.7Counter64read-onlycurrent
wanPppHistoryOutOctets
OBJECT-TYPE
The change in value of wanPppStatsOutOctets during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.8Counter64read-onlycurrent
wanPppHistoryInBadAddresses
OBJECT-TYPE
The change in value of wanPppStatsInBadAddresses during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.9Counter64read-onlycurrent
wanPppHistoryOutBadAddresses
OBJECT-TYPE
The change in value of wanPppStatsOutBadAddresses during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.10Counter64read-onlycurrent
wanPppHistoryInBadControls
OBJECT-TYPE
The change in value of wanPppStatsInBadControls during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.11Counter64read-onlycurrent
wanPppHistoryOutBadControls
OBJECT-TYPE
The change in value of wanPppStatsOutBadControls during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.12Counter64read-onlycurrent
wanPppHistoryInLongFrames
OBJECT-TYPE
The change in value of wanPppStatsInLongFrames during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.13Counter64read-onlycurrent
wanPppHistoryOutLongFrames
OBJECT-TYPE
The change in value of wanPppStatsOutLongFrames during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.14Counter64read-onlycurrent
wanPppHistoryInBadFCSs
OBJECT-TYPE
The change in value of wanPppStatsInBadFCSs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.15Counter64read-onlycurrent
wanPppHistoryOutBadFCSs
OBJECT-TYPE
The change in value of wanPppStatsOutBadFCSs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.16Counter64read-onlycurrent
wanPppHistoryInUtilization
OBJECT-TYPE
The best estimated of the mean physical layer network utilization of traffic coming from the far end of the link in hundreds of a percent.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.17INTEGER (0..10000)read-onlycurrent
wanPppHistoryOutUtilization
OBJECT-TYPE
The best estimated of the mean physical layer network utilization of traffic coming from the near end of the link in hundreds of a percent.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.18INTEGER (0..10000)read-onlycurrent
wanPvcHistory
OBJECT-IDENTITY
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3
wanX25PvcHistoryTable
OBJECT-TYPE
X.25 per LCI statistics.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1not-accessiblecurrent
wanX25PvcHistoryEntry
OBJECT-TYPE
The statistics for a X.25 LCI. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1not-accessiblecurrent
wanX25PvcHistoryIndex
OBJECT-TYPE
The history of which this entry is a port. The history identified by a particular value of this index is the same history as identified by the same value of historyControlIndex.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.1INTEGER (1..65535)not-accessiblecurrent
wanX25PvcHistorySampleIndex
OBJECT-TYPE
An index that uniquely identifies the particular sample this entry represents among all samples associated with the same historyControlEntry. This index starts at 1 and increases by one as each new sample is taken.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.2INTEGER (1..2147483647)not-accessiblecurrent
wanX25PvcHistoryIntervalStart
OBJECT-TYPE
The value of sysUpTime at the start of the interval over which this sample was measured. If the probe keeps track of time of day, it should start the first sample of the history at a time such that when the next hour of the day begins, a sample is started at that instant. Note that following this rule may require the probe to delay collection the first sample of the history, as each sample must be of the same interval. Also note that the sample which is currently being collected is not accessible in this table until the end of its interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.3TimeTicksread-onlycurrent
wanX25PvcHistoryDropEvents
OBJECT-TYPE
The change in value of wanX25PvcStatsDropEvents during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.4Counter64read-onlycurrent
wanX25PvcHistoryInFrames
OBJECT-TYPE
The change in value of wanX25PvcStatsInFrames during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.5Counter64read-onlycurrent
wanX25PvcHistoryOutFrames
OBJECT-TYPE
The change in value of wanX25PvcStatsOutFrames during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.6Counter64read-onlycurrent
wanX25PvcHistoryInOctets
OBJECT-TYPE
The change in value of wanX25PvcStatsInOctets during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.7Counter64read-onlycurrent
wanX25PvcHistoryOutOctets
OBJECT-TYPE
The change in value of wanX25PvcStatsOutOctets during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.8Counter64read-onlycurrent
wanX25PvcHistoryInResets
OBJECT-TYPE
The change in value of wanX25PvcStatsInResets during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.9Counter64read-onlycurrent
wanX25PvcHistoryOutResets
OBJECT-TYPE
The change in value of wanX25PvcStatsOutResets during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.10Counter64read-onlycurrent
wanX25PvcHistoryProviderResets
OBJECT-TYPE
The change in value of wanX25PvcStatsProviderResets during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.11Counter64read-onlycurrent
wanX25PvcHistoryInAccusedErrors
OBJECT-TYPE
The change in value of wanX25PvcStatsInAccusedErrors during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.12Counter64read-onlycurrent
wanX25PvcHistoryOutAccusedErrors
OBJECT-TYPE
The change in value of wanX25PvcStatsOutAccusedErrors during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.13Counter64read-onlycurrent
wanX25PvcHistoryInInterrupts
OBJECT-TYPE
The change in value of wanX25PvcStatsInInterrupts during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.14Counter64read-onlycurrent
wanX25PvcHistoryOutInterrupts
OBJECT-TYPE
The change in value of wanX25PvcStatsOutInterrupts during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.15Counter64read-onlycurrent
wanX25PvcHistoryUpTime
OBJECT-TYPE
The change in value of wanX25PvcStatsUpTime during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.16TimeTicksread-onlycurrent
wanX25PvcHistoryDownTime
OBJECT-TYPE
The change in value of wanX25PvcStatsDownTime during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.17TimeTicksread-onlycurrent
wanX25PvcHistoryStateChanges
OBJECT-TYPE
The change in value of wanX25PvcStatsStateChanges during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.18Counter64read-onlycurrent
wanX25PvcHistoryInUtilization
OBJECT-TYPE
The best estimated of the mean utilization of traffic on this LCI coming from the far end of the link in hundreds of percent of the CIR.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.19INTEGER (0..10000)read-onlycurrent
wanX25PvcHistoryOutUtilization
OBJECT-TYPE
The best estimated of the mean utilization of traffic on this LCI coming from the near end of the link in hundreds of percent of CIR.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.20INTEGER (0..10000)read-onlycurrent
wanFrPvcHistoryTable
OBJECT-TYPE
Frame Relay per-DCLI statistics.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2not-accessiblecurrent
wanFrPvcHistoryEntry
OBJECT-TYPE
The statistics for a frame relay DLCI. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1not-accessiblecurrent
wanFrPvcHistoryIndex
OBJECT-TYPE
The history of which this entry is a port. The history identified by a particular value of this index is the same history as identified by the same value of historyControlIndex.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.1INTEGER (1..65535)not-accessiblecurrent
wanFrPvcHistorySampleIndex
OBJECT-TYPE
An index that uniquely identifies the particular sample this entry represents among all samples associated with the same historyControlEntry. This index starts at 1 and increases by one as each new sample is taken.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.2INTEGER (1..2147483647)not-accessiblecurrent
wanFrPvcHistoryIntervalStart
OBJECT-TYPE
The value of sysUpTime at the start of the interval over which this sample was measured. If the probe keeps track of time of day, it should start the first sample of the history at a time such that when the next hour of the day begins, a sample is started at that instant. Note that following this rule may require the probe to delay collection the first sample of the history, as each sample must be of the same interval. Also note that the sample which is currently being collected is not accessible in this table until the end of its interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.3TimeTicksread-onlycurrent
wanFrPvcHistoryDropEvents
OBJECT-TYPE
The change in value of wanFrPvcStatsDropEvents during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.4Counter64read-onlycurrent
wanFrPvcHistoryInFrames
OBJECT-TYPE
The change in value of wanFrPvcStatsInFrames during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.5Counter64read-onlycurrent
wanFrPvcHistoryOutFrames
OBJECT-TYPE
The change in value of wanFrPvcStatsOutFrames during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.6Counter64read-onlycurrent
wanFrPvcHistoryInOctets
OBJECT-TYPE
The change in value of wanFrPvcStatsInOctets during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.7Counter64read-onlycurrent
wanFrPvcHistoryOutOctets
OBJECT-TYPE
The change in value of wanFrPvcStatsOutOctets during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.8Counter64read-onlycurrent
wanFrPvcHistoryInFECNs
OBJECT-TYPE
The change in value of wanFrPvcStatsInFECNs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.9Counter64read-onlycurrent
wanFrPvcHistoryOutFECNs
OBJECT-TYPE
The change in value of wanFrPvcStatsOutFECNs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.10Counter64read-onlycurrent
wanFrPvcHistoryInBECNs
OBJECT-TYPE
The change in value of wanFrPvcStatsInBECNs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.11Counter64read-onlycurrent
wanFrPvcHistoryOutBECNs
OBJECT-TYPE
The change in value of wanFrPvcStatsOutBECNs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.12Counter64read-onlycurrent
wanFrPvcHistoryInDEs
OBJECT-TYPE
The change in value of wanFrPvcStatsInDEs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.13Counter64read-onlycurrent
wanFrPvcHistoryOutDEs
OBJECT-TYPE
The change in value of wanFrPvcStatsOutDEs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.14Counter64read-onlycurrent
wanFrPvcHistoryUpTime
OBJECT-TYPE
The change in value of wanFrPvcStatsUpTime during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.15TimeTicksread-onlycurrent
wanFrPvcHistoryDownTime
OBJECT-TYPE
The change in value of wanFrPvcStatsDownTime during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.16TimeTicksread-onlycurrent
wanFrPvcHistoryStateChanges
OBJECT-TYPE
The change in value of wanFrPvcStatsStateChanges during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.17Counter64read-onlycurrent
wanFrPvcHistoryInUtilization
OBJECT-TYPE
The best estimated of the mean utilization of traffic on this DLCI coming from the far end of the link in hundreds of percent of the CIR.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.18INTEGER (0..10000)read-onlycurrent
wanFrPvcHistoryOutUtilization
OBJECT-TYPE
The best estimated of the mean utilization of traffic on this DLCI coming from the near end of the link in hundreds of percent of CIR.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.19INTEGER (0..10000)read-onlycurrent
wanAal5PvcHistoryTable
OBJECT-TYPE
AAL-5 per-VPI/VCI statistics.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3not-accessiblecurrent
wanAal5PvcHistoryEntry
OBJECT-TYPE
The statistics for a AAL-5 VCI/VPI. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1not-accessiblecurrent
wanAal5PvcHistoryIndex
OBJECT-TYPE
The history of which this entry is a port. The history identified by a particular value of this index is the same history as identified by the same value of historyControlIndex.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.1INTEGER (1..65535)not-accessiblecurrent
wanAal5PvcHistorySampleIndex
OBJECT-TYPE
An index that uniquely identifies the particular sample this entry represents among all samples associated with the same historyControlEntry. This index starts at 1 and increases by one as each new sample is taken.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.2INTEGER (1..2147483647)not-accessiblecurrent
wanAal5PvcHistoryIntervalStart
OBJECT-TYPE
The value of sysUpTime at the start of the interval over which this sample was measured. If the probe keeps track of time of day, it should start the first sample of the history at a time such that when the next hour of the day begins, a sample is started at that instant. Note that following this rule may require the probe to delay collection the first sample of the history, as each sample must be of the same interval. Also note that the sample which is currently being collected is not accessible in this table until the end of its interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.3TimeTicksread-onlycurrent
wanAal5PvcHistoryDropEvents
OBJECT-TYPE
The change in value of wanAal5PvcStatsDropEvents during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.4Counter64read-onlycurrent
wanAal5PvcHistoryInCells
OBJECT-TYPE
The change in value of wanAal5PvcStatsInCells during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.5Counter64read-onlycurrent
wanAal5PvcHistoryOutCells
OBJECT-TYPE
The change in value of wanAal5PvcStatsOutCells during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.6Counter64read-onlycurrent
wanAal5PvcHistoryInPDUs
OBJECT-TYPE
The change in value of wanAal5PvcStatsInPDUs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.7Counter64read-onlycurrent
wanAal5PvcHistoryOutPDUs
OBJECT-TYPE
The change in value of wanAal5PvcStatsOutPDUs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.8Counter64read-onlycurrent
wanAal5PvcHistoryInOctets
OBJECT-TYPE
The change in value of wanAal5PvcStatsInOctets during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.9Counter64read-onlycurrent
wanAal5PvcHistoryOutOctets
OBJECT-TYPE
The change in value of wanAal5PvcStatsOutOctets during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.10Counter64read-onlycurrent
wanAal5PvcHistoryInCLP1
OBJECT-TYPE
The change in value of wanAal5PvcStatsInCLP1 during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.11Counter64read-onlycurrent
wanAal5PvcHistoryOutCLP1
OBJECT-TYPE
The change in value of wanAal5PvcStatsOutCLP1 during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.12Counter64read-onlycurrent
wanAal5PvcHistoryInCRCs
OBJECT-TYPE
The change in value of wanAal5PvcStatsInCRCs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.13Counter64read-onlycurrent
wanAal5PvcHistoryOutCRCs
OBJECT-TYPE
The change in value of wanAal5PvcStatsOutCRCs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.14Counter64read-onlycurrent
wanAal5PvcHistoryInOversizedSDUs
OBJECT-TYPE
The change in value of wanAal5PvcStatsInOversizedSDUs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.15Counter64read-onlycurrent
wanAal5PvcHistoryOutOversizedSDUs
OBJECT-TYPE
The change in value of wanAal5PvcStatsOutOversizedSDUs during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.16Counter64read-onlycurrent
wanAal5PvcHistoryUpTime
OBJECT-TYPE
The change in value of wanAal5PvcStatsUpTime during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.17TimeTicksread-onlycurrent
wanAal5PvcHistoryDownTime
OBJECT-TYPE
The change in value of wanAal5PvcStatsDownTime during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.18TimeTicksread-onlycurrent
wanAal5PvcHistoryStateChanges
OBJECT-TYPE
The change in value of wanAal5PvcStatsStateChanges during the interval.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.19Counter64read-onlycurrent
wanAal5PvcHistoryInUtilization
OBJECT-TYPE
The best estimated of the mean utilization of traffic on this VPI/VCI coming from the far end of the link in hundreds of percent of the CIR.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.20INTEGER (0..10000)read-onlycurrent
wanAal5PvcHistoryOutUtilization
OBJECT-TYPE
The best estimated of the mean utilization of traffic on this VPI/VCI coming from the near end of the link in hundreds of percent of CIR.
1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.21INTEGER (0..10000)read-onlycurrent