MIBs Depot

UPS2-MIB

Registered at
1.3.6.1.4.1.52.4.1.1.10.1
1.3.6.1.4.1.52.4.1.1.10.2
1.3.6.1.4.1.52.4.1.1.10.3
1.3.6.1.4.1.52.4.1.1.10.4
1.3.6.1.4.1.52.4.1.1.10.5
1.3.6.1.4.1.52.4.1.1.10.6
1.3.6.1.4.1.52.4.1.1.10.7
1.3.6.1.4.1.52.4.1.1.10.8
1.3.6.1.4.1.52.4.1.1.10.9
Namespace
enterasys
Source file
UPS2-MIB
Digest
sha256:760f376592f33f5b3a60a3476f74bb1d8c89eee15093341741256dda4affd60f

Imports

FromSymbols
CTRON-MIB-NAMESctUPS
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP
SNMPv2-SMIMODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, iso
SNMPv2-TCDisplayString, TEXTUAL-CONVENTION

Imported by

Nothing in this corpus imports this module.

Load order

Every file a consumer needs in order to load this module, dependencies first.

CTRON-MIB-NAMES
CTRON-OIDS
SNMPv2-CONF
SNMPv2-SMI
SNMPv2-TC
UPS2-MIB

Objects

NameOIDSyntaxAccessStatus
upsSystem
OBJECT-IDENTITY
1.3.6.1.4.1.52.4.1.1.10.1
upsNumUPSs
OBJECT-TYPE
The number of UPSs available.
1.3.6.1.4.1.52.4.1.1.10.1.1INTEGER (0..2)read-onlymandatory
upsId
OBJECT-IDENTITY
1.3.6.1.4.1.52.4.1.1.10.2
upsIdTable
OBJECT-TYPE
A list of identification table entries. The number of entries is given by the value of upsNumUPSs.
1.3.6.1.4.1.52.4.1.1.10.2.1not-accessiblemandatory
upsIdEntry
OBJECT-TYPE
An entry containing objects for a particular UPS.
1.3.6.1.4.1.52.4.1.1.10.2.1.1not-accessiblemandatory
upsIndex
OBJECT-TYPE
A unique value which identifies a particular UPS.
1.3.6.1.4.1.52.4.1.1.10.2.1.1.1INTEGERread-onlymandatory
upsName
OBJECT-TYPE
The UPS's name. A maximum of 8 characters may be specified. This object is initialized to the UPS's model name.
1.3.6.1.4.1.52.4.1.1.10.2.1.1.2DisplayString (SIZE(0..8))read-writemandatory
upsModelType
OBJECT-TYPE
The UPS's base model type.
1.3.6.1.4.1.52.4.1.1.10.2.1.1.3INTEGER {smartUps250(1), smartUps400(2), smartUps600(3), smartUps900(4), smartUps1250(5), smartUps2000(6), matrixUps3000(7), matrixUps5000(8), other(9)}read-onlymandatory
upsFwVersion
OBJECT-TYPE
The UPS's firmware version.
1.3.6.1.4.1.52.4.1.1.10.2.1.1.4DisplayString (SIZE(0..8))read-onlymandatory
upsSerialNumber
OBJECT-TYPE
The UPS's serial number as set at the factory.
1.3.6.1.4.1.52.4.1.1.10.2.1.1.5DisplayString (SIZE(0..16))read-onlymandatory
upsManufDate
OBJECT-TYPE
The UPS's date of manufacture in the format mm/dd/yy.
1.3.6.1.4.1.52.4.1.1.10.2.1.1.6DisplayString (SIZE(0..8))read-onlymandatory
upsBattery
OBJECT-IDENTITY
1.3.6.1.4.1.52.4.1.1.10.3
upsBatteryTable
OBJECT-TYPE
A list of battery table entries. The number of entries is given by the value of upsNumUPSs.
1.3.6.1.4.1.52.4.1.1.10.3.1not-accessiblemandatory
upsBatteryEntry
OBJECT-TYPE
An entry containing objects for a particular UPS.
1.3.6.1.4.1.52.4.1.1.10.3.1.1not-accessiblemandatory
upsBatteryCapacity
OBJECT-TYPE
The UPS's remaining battery capacity expressed as a percent of the fully charged condition. The value of this object is the actual percentage * 10 (that is, to determine the actual percentage, divide the value of this object by 10).
1.3.6.1.4.1.52.4.1.1.10.3.1.1.1INTEGERread-onlymandatory
upsBatteryVoltage
OBJECT-TYPE
The UPS's present battery voltage. The value of this object is the actual voltage * 100 (that is, to determine the actual voltage, divide the value of this object by 100).
1.3.6.1.4.1.52.4.1.1.10.3.1.1.2INTEGERread-onlymandatory
upsBatteryTest
OBJECT-TYPE
This object may be written to initiate testing of the UPS's battery packs. Reading this object will always return a 0.
1.3.6.1.4.1.52.4.1.1.10.3.1.1.3INTEGER {initiateTest(1)}read-writemandatory
upsBatteryTestResult
OBJECT-TYPE
The result of the last battery test performed.
1.3.6.1.4.1.52.4.1.1.10.3.1.1.4INTEGER {batteryOK(1), batteryBad(2), noRecentTest(3), invalidTestDueToOverload(4)}read-onlymandatory
upsRunTimeCalibration
OBJECT-TYPE
This object may be written to initiate or terminate the test used to calibrate the returned run time value. This test will only run if battery capacity is 100%. Results of this test can be retrieved by upsEstimatedRunTimeRemaining. Valid values for writing are 1 (initiate test) and 2 (terminate test). In addition, this object may be read to determine whether the test is currently running. Valid values for reading are 3 (test is in progress) and 4 (test is not in progress).
1.3.6.1.4.1.52.4.1.1.10.3.1.1.5INTEGER {performTest(1), abortTest(2), testInProgress(3), testNotInProgress(4)}read-writemandatory
upsEstimatedRunTimeRemaining
OBJECT-TYPE
The UPS's estimated remaining run time in minutes. The UPS may be queried when operating in the on-line, bypass, or on-battery modes of operation. The run time estimate is based on available battery capacity and output load.
1.3.6.1.4.1.52.4.1.1.10.3.1.1.6INTEGERread-onlymandatory
upsTransferCause
OBJECT-TYPE
The reason for the most recent transfer to on-battery operation.
1.3.6.1.4.1.52.4.1.1.10.3.1.1.7INTEGER {noTransfer(1), selfTest(2), inputLineSpike(3), inputLowVoltage(4), inputHighVoltage(5), inputLineFrequencyBad(6)}read-onlymandatory
upsBatteryTestTime
OBJECT-TYPE
The frequency of execution of the UPS's automatic battery test. The test may be run immediately upon startup, upon startup and every 7 days thereafter, upon startup and every 14 days thereafter, or never.
1.3.6.1.4.1.52.4.1.1.10.3.1.1.8INTEGER {twoWeeks(1), oneWeek(2), startupOnly(3), off(4)}read-writemandatory
upsLowBatteryWarning
OBJECT-TYPE
The interval between activation of the UPS's low battery alarm warnings and shutdown of the UPS.
1.3.6.1.4.1.52.4.1.1.10.3.1.1.9INTEGER {twoMinutes(1), fiveMinutes(2), sevenMinutes(3), tenMinutes(4)}read-writemandatory
upsInput
OBJECT-IDENTITY
1.3.6.1.4.1.52.4.1.1.10.4
upsInputTable
OBJECT-TYPE
A list of input table entries. The number of entries is given by the value of upsNumUPSs.
1.3.6.1.4.1.52.4.1.1.10.4.1not-accessiblemandatory
upsInputEntry
OBJECT-TYPE
An entry containing objects for a particular UPS.
1.3.6.1.4.1.52.4.1.1.10.4.1.1not-accessiblemandatory
upsInputUtilityVoltage
OBJECT-TYPE
The UPS's utility voltage version.
1.3.6.1.4.1.52.4.1.1.10.4.1.1.1INTEGER {vac100(1), vac120(2), vac208(3), vac220(4)}read-onlymandatory
upsInputVoltage
OBJECT-TYPE
The UPS's measured utility input voltage. The value of this object is the actual voltage * 10 (that is, to determine the actual voltage, divide the value of this object by 10).
1.3.6.1.4.1.52.4.1.1.10.4.1.1.2INTEGERread-onlymandatory
upsInputFailureSensitivity
OBJECT-TYPE
The sensitivity of the UPS to rapid changes in utility voltage (e.g., blackouts, spikes, or notches) or abnormal changes in utility frequency.
1.3.6.1.4.1.52.4.1.1.10.4.1.1.3INTEGER {high(1), medium(2), low(3), auto(4)}read-writemandatory
upsInputMaxVoltage
OBJECT-TYPE
The UPS's maximum input voltage recorded since this object was last read. The value of this object is the actual voltage * 10 (that is, to determine the actual voltage, divide the value of this object by 10).
1.3.6.1.4.1.52.4.1.1.10.4.1.1.4INTEGERread-onlymandatory
upsInputMinVoltage
OBJECT-TYPE
The UPS's minimum input voltage recorded since this object was last read. The value of this object is the actual voltage * 10 (that is, to determine the actual voltage, divide the value of this object by 10).
1.3.6.1.4.1.52.4.1.1.10.4.1.1.5INTEGERread-onlymandatory
upsInputFrequency
OBJECT-TYPE
The UPS's present internal operating frequency in Hz. The value of this object is the actual frequency * 100 (that is, to determine the actual frequency, divide the value of this object by 100).
1.3.6.1.4.1.52.4.1.1.10.4.1.1.6INTEGERread-onlymandatory
upsOutput
OBJECT-IDENTITY
1.3.6.1.4.1.52.4.1.1.10.5
upsOutputTable
OBJECT-TYPE
A list of output table entries. The number of entries is given by the value of upsNumUPSs.
1.3.6.1.4.1.52.4.1.1.10.5.1not-accessiblemandatory
upsOutputEntry
OBJECT-TYPE
An entry containing objects for a particular UPS.
1.3.6.1.4.1.52.4.1.1.10.5.1.1not-accessiblemandatory
upsOutputVoltage
OBJECT-TYPE
The measured UPS output voltage. The value of this object is the actual voltage * 10 (that is, to determine the actual voltage, divide the value of this object by 10).
1.3.6.1.4.1.52.4.1.1.10.5.1.1.1INTEGERread-onlymandatory
upsOutputUtilityVoltage
OBJECT-TYPE
The UPS's current on-battery output voltage setting (valid for 220/230/240 Vac version UPSs only). For other version UPSs, reading this object will always return a 0 and writing this object will have no effect.
1.3.6.1.4.1.52.4.1.1.10.5.1.1.2INTEGER {vac225(1), vac230(2), vac240(3), vac220(4)}read-writemandatory
upsOutputPower
OBJECT-TYPE
The UPS's output load represented as a percentage of full rated load in Watts. The value of this object is the actual percentage * 10 (that is, to determine the actual percentage, divide the value of this object by 10).
1.3.6.1.4.1.52.4.1.1.10.5.1.1.3INTEGERread-onlymandatory
upsStatus
OBJECT-IDENTITY
1.3.6.1.4.1.52.4.1.1.10.6
upsStatusTable
OBJECT-TYPE
A list of status table entries. The number of entries is given by the value of upsNumUPSs.
1.3.6.1.4.1.52.4.1.1.10.6.1not-accessiblemandatory
upsStatusEntry
OBJECT-TYPE
An entry containing objects for a particular UPS.
1.3.6.1.4.1.52.4.1.1.10.6.1.1not-accessiblemandatory
upsStatusOperational
OBJECT-TYPE
This object contains 8 bits of information about the current operational status of the UPS. The bits are encoded as follows: BIT 7: 1=replace battery condition BIT 6: 1=low battery condition BIT 5: 1=overloaded output condition BIT 4: 1=on-battery mode of operation BIT 3: 1=on-line mode of operation BIT 2: 1=Smart Boost mode of operation (where applicable) BIT 1: 1=UPS shut down due to low battery, overload, or `sleep' mode BIT 0: 1=run time calibration running Note that bit 0 is the low-order bit.
1.3.6.1.4.1.52.4.1.1.10.6.1.1.1INTEGERread-onlymandatory
upsStatusFault
OBJECT-TYPE
This object contains 8 bits of information about the current fault conditions of the UPS. The bits are encoded as follows: BIT 7: 1=UPS fault - internal temperature has exceeded nominal limits BIT 6: 1=UPS fault - bypass relay (where applicable) malfunction BIT 5: 1=UPS fault - battery charger failure BIT 4: 1=UPS in shut down mode via `S' command BIT 3: 1=UPS in `sleep' mode via `@ddd' command BIT 2: 1=UPS fault - main relay malfunction BIT 1: 1=UPS unable to transfer to on-battery operation due to overload BIT 0: 1=UPS's output unpowered due to low battery shut down Note that bit 0 is the low-order bit.
1.3.6.1.4.1.52.4.1.1.10.6.1.1.2INTEGERread-onlymandatory
upsStatusTemp
OBJECT-TYPE
The UPS's present internal operating temperature in degrees Fahrenheit. The value of this object is the actual temperature * 10 (that is, to determine the actual temperature, divide the value of this object by 10).
1.3.6.1.4.1.52.4.1.1.10.6.1.1.3INTEGERread-onlymandatory
upsConfig
OBJECT-IDENTITY
1.3.6.1.4.1.52.4.1.1.10.7
upsConfigTable
OBJECT-TYPE
A list of configuration table entries. The number of entries is given by the value of upsNumUPSs.
1.3.6.1.4.1.52.4.1.1.10.7.1not-accessiblemandatory
upsConfigEntry
OBJECT-TYPE
An entry containing objects for a particular UPS.
1.3.6.1.4.1.52.4.1.1.10.7.1.1not-accessiblemandatory
upsConfigAlarm
OBJECT-TYPE
The UPS's current audible alarm setting. The alarm may be set to activate immediately upon utility failure and for low battery condition, to activate 30 seconds after utility failure and immediately upon low battery condition, to activate upon low battery condition only, or to not activate under any conditions.
1.3.6.1.4.1.52.4.1.1.10.7.1.1.1INTEGER {uponUtilityFailure(1), thirtySecondsAfterUtilityFailure(2), lowBatteryOnly(3), noAudibleAlarm(4)}read-writemandatory
upsConfigRestoreDefaults
OBJECT-TYPE
This object may be written to force the UPS to restore the factory default settings for most of the UPS's customizable parameters. Reading this object will always return a 0.
1.3.6.1.4.1.52.4.1.1.10.7.1.1.2INTEGER {restoreDefaults(1)}read-writemandatory
upsExtMeas
OBJECT-IDENTITY
1.3.6.1.4.1.52.4.1.1.10.8
upsExtMeasTable
OBJECT-TYPE
A list of external measurement table entries. The number of entries is the number of available UPSs to which External Measurement Units are attached.
1.3.6.1.4.1.52.4.1.1.10.8.1not-accessiblemandatory
upsExtMeasEntry
OBJECT-TYPE
An entry containing objects for a particular UPS.
1.3.6.1.4.1.52.4.1.1.10.8.1.1not-accessiblemandatory
upsExtMeasFwVersion
OBJECT-TYPE
The External Measurement Unit's firmware version letter.
1.3.6.1.4.1.52.4.1.1.10.8.1.1.1DisplayString (SIZE(0..1))read-onlymandatory
upsExtMeasTemp
OBJECT-TYPE
The local ambient temperature in degrees Fahrenheit as measured by the External Measurement Unit. The value of this object is the actual temperature * 100 (that is, to determine the actual temperature, divide the value of this object by 100).
1.3.6.1.4.1.52.4.1.1.10.8.1.1.2INTEGERread-onlymandatory
upsExtMeasHumidity
OBJECT-TYPE
The local ambient relative humidity in percent as measured by the External Measurement Unit. The value of this object is the actual humidity * 10 (that is, to determine the actual humidity, divide the value of this object by 10).
1.3.6.1.4.1.52.4.1.1.10.8.1.1.3INTEGERread-onlymandatory
upsExtMeasAlarmStatus
OBJECT-TYPE
This object contains 8 bits of information about the current alarm status of the External Measurement Unit. The bits are encoded as follows: BIT 7: 1=Upper temperature limit exceeded BIT 6: 1=Lower temperature limit exceeded BIT 5: 1=Upper relative humidity limit exceeded BIT 4: 1=Lower relative humidity limit exceeded BIT 3: 1=Contact input channel #4 alarm state BIT 2: 1=Contact input channel #3 alarm state BIT 1: 1=Contact input channel #2 alarm state BIT 0: 1=Contact input channel #1 alarm state Note that bit 0 is the low-order bit.
1.3.6.1.4.1.52.4.1.1.10.8.1.1.4INTEGERread-onlymandatory
upsExtMeasMaxTemp
OBJECT-TYPE
The upper temperature limit at which an alarm will be sent.
1.3.6.1.4.1.52.4.1.1.10.8.1.1.5INTEGER {ninetyDegreesF(1), oneHundredFifteenDegreesF(2), oneHundredThirtyDegreesF(3), oneHundredSeventyFiveDegreesF(4)}read-writemandatory
upsExtMeasMinTemp
OBJECT-TYPE
The lower temperature limit at which an alarm will be sent.
1.3.6.1.4.1.52.4.1.1.10.8.1.1.6INTEGER {fortyDegreesF(1), fiftyDegreesF(2), fiftyEightDegreesF(3), sixtyFiveDegreesF(4)}read-writemandatory
upsExtMeasMaxHumidity
OBJECT-TYPE
The upper humidity limit at which an alarm will be sent.
1.3.6.1.4.1.52.4.1.1.10.8.1.1.7INTEGER {seventyPercent(1), eightyPercent(2), eightyFivePercent(3), ninetyPercent(4)}read-writemandatory
upsExtMeasMinHumidity
OBJECT-TYPE
The lower humidity limit at which an alarm will be sent.
1.3.6.1.4.1.52.4.1.1.10.8.1.1.8INTEGER {tenPercent(1), twentyPercent(2), thirtyPercent(3), fortyPercent(4)}read-writemandatory
upsExtMeasContact1AlarmControl
OBJECT-TYPE
The alarm enable state for the External Measurement Unit's contact input channel #1. If enabled, an alarm will be sent when contact input channel #1 has changed to abnormal state.
1.3.6.1.4.1.52.4.1.1.10.8.1.1.9INTEGER {enable(1), disable(2)}read-writemandatory
upsExtMeasContact2AlarmControl
OBJECT-TYPE
The alarm enable state for the External Measurement Unit's contact input channel #2. If enabled, an alarm will be sent when contact input channel #2 has changed to abnormal state.
1.3.6.1.4.1.52.4.1.1.10.8.1.1.10INTEGER {enable(1), disable(2)}read-writemandatory
upsExtMeasContact3AlarmControl
OBJECT-TYPE
The alarm enable state for the External Measurement Unit's contact input channel #3. If enabled, an alarm will be sent when contact input channel #3 has changed to abnormal state.
1.3.6.1.4.1.52.4.1.1.10.8.1.1.11INTEGER {enable(1), disable(2)}read-writemandatory
upsExtMeasContact4AlarmControl
OBJECT-TYPE
The alarm enable state for the External Measurement Unit's contact input channel #4. If enabled, an alarm will be sent when contact input channel #4 has changed to abnormal state.
1.3.6.1.4.1.52.4.1.1.10.8.1.1.12INTEGER {enable(1), disable(2)}read-writemandatory
upsExtMeasMaxTempAlarmControl
OBJECT-TYPE
The alarm enable state for the External Measurement Unit's upper temperature limit. If enabled, an alarm will be sent when the ambient temperature rises above the upper temperature limit.
1.3.6.1.4.1.52.4.1.1.10.8.1.1.13INTEGER {enable(1), disable(2)}read-writemandatory
upsExtMeasMinTempAlarmControl
OBJECT-TYPE
The alarm enable state for the External Measurement Unit's lower temperature limit. If enabled, an alarm will be sent when the ambient temperature falls below the lower temperature limit.
1.3.6.1.4.1.52.4.1.1.10.8.1.1.14INTEGER {enable(1), disable(2)}read-writemandatory
upsExtMeasMaxHumidityAlarmControl
OBJECT-TYPE
The alarm enable state for the External Measurement Unit's upper humidity limit. If enabled, an alarm will be sent when the ambient relative humidity rises above the upper humidity limit.
1.3.6.1.4.1.52.4.1.1.10.8.1.1.15INTEGER {enable(1), disable(2)}read-writemandatory
upsExtMeasMinHumidityAlarmControl
OBJECT-TYPE
The alarm enable state for the External Measurement Unit's lower humidity limit. If enabled, an alarm will be sent when the ambient relative humidity falls below the lower humidity limit.
1.3.6.1.4.1.52.4.1.1.10.8.1.1.16INTEGER {enable(1), disable(2)}read-writemandatory
upsAddlFuncs
OBJECT-IDENTITY
1.3.6.1.4.1.52.4.1.1.10.9
upsAddlFuncsTable
OBJECT-TYPE
A list of additional functions table entries. The number of entries is the number of available UPSs which are capable of supporting these additional functions.
1.3.6.1.4.1.52.4.1.1.10.9.1not-accessiblemandatory
upsAddlFuncsEntry
OBJECT-TYPE
An entry containing objects for a particular UPS.
1.3.6.1.4.1.52.4.1.1.10.9.1.1not-accessiblemandatory
upsAddlFuncsNumBatteryPacks
OBJECT-TYPE
The number of battery pack units connected to the UPS.
1.3.6.1.4.1.52.4.1.1.10.9.1.1.1INTEGERread-onlymandatory
upsAddlFuncsNumBadBatteryPacks
OBJECT-TYPE
The number of bad (faulty) battery pack units connected to the UPS.
1.3.6.1.4.1.52.4.1.1.10.9.1.1.2INTEGERread-onlymandatory
upsAddlFuncsOutputCurrent
OBJECT-TYPE
The true rms load current drawn from the UPS. The value of this object is the actual amperage * 100 (that is, to determine the actual amperage, divide the value of this object by 100).
1.3.6.1.4.1.52.4.1.1.10.9.1.1.3INTEGERread-onlymandatory
upsAddlFuncsOutputApparentPower
OBJECT-TYPE
The UPS's output load represented as a percentage of full rated load in Volt-Amps. The value of this object is the actual percentage * 10 (that is, to determine the actual percentage, divide the value of this object by 10).
1.3.6.1.4.1.52.4.1.1.10.9.1.1.4INTEGERread-onlymandatory
upsAddlFuncsStatusOperational
OBJECT-TYPE
This object contains 8 bits of information about the current operational status of the UPS. The bits are encoded as follows: BIT 7: 1=UPS ready to power load upon return of normal line or upon user command BIT 6: 1=UPS ready to power load upon user command BIT 5: 1=UPS in bypass mode as a result of manual bypass control BIT 4: 1=UPS is returning from bypass mode BIT 3: 1=UPS in bypass mode as a result of UPS-Link or key command BIT 2: 1=UPS going to bypass mode as a result of UPS-Link or key command BIT 1: 1=not defined BIT 0: 1=wakeup mode - startup test lasting < 2 sec Note that bit 0 is the low-order bit.
1.3.6.1.4.1.52.4.1.1.10.9.1.1.5INTEGERread-onlymandatory
upsAddlFuncsStatusFault
OBJECT-TYPE
This object contains 8 bits of information about the current fault conditions of the UPS. The bits are encoded as follows: BIT 7: reserved for future use BIT 6: reserved for future use BIT 5: reserved for future use BIT 4: 1=UPS fault - DC imbalance, UPS in bypass BIT 3: 1=UPS fault - output voltage select failure, UPS in bypass BIT 2: 1=UPS fault - bypass supply failure BIT 1: 1=UPS fault - Isolation Unit fan failure BIT 0: 1=UPS fault - Electronics Unit fan failure, UPS in bypass Note that bit 0 is the low-order bit.
1.3.6.1.4.1.52.4.1.1.10.9.1.1.6INTEGERread-onlymandatory
upsAddlFuncsConfigPassword
OBJECT-TYPE
The password that controls access to the UPS's LCD display. A maximum of 4 characters may be entered.
1.3.6.1.4.1.52.4.1.1.10.9.1.1.7OCTET STRINGread-writemandatory
upsAddlFuncsConfigDisable
OBJECT-TYPE
This object may be written to immediately shut down the UPS, requiring a manual reset. Reading this object will always return a 0.
1.3.6.1.4.1.52.4.1.1.10.9.1.1.8INTEGER {disableUps(1)}read-writemandatory
upsAddlFuncsConfigBypass
OBJECT-TYPE
This object may be written to cause the UPS to transfer to or from the bypass mode. Reading this object will always return a 0.
1.3.6.1.4.1.52.4.1.1.10.9.1.1.9INTEGER {bypassMode(1), exitBypassMode(2)}read-writemandatory