MIBs Depot

TELECOM-MIB

Registered at
1.3.6.1.4.1.935.10.2
Namespace
eaton
Source file
TELECOM-MIB
Digest
sha256:cfcff613695f97acd83d19e2a107b1470f4090bcd77ffb362ff4aac614cb86d3

Imports

FromSymbols
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP
SNMPv2-SMICounter32, IpAddress, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TRAP-TYPE, enterprises, iso
SNMPv2-TCDisplayString, TEXTUAL-CONVENTION

Imported by

Nothing in this corpus imports this module.

Load order

Every file a consumer needs in order to load this module, dependencies first.

SNMPv2-CONF
SNMPv2-SMI
SNMPv2-TC
TELECOM-MIB

Textual conventions

NameOIDSyntaxAccessStatus
NonNegativeInteger
TEXTUAL-CONVENTION
This data type is a non-negative value.
current
PositiveInteger
TEXTUAL-CONVENTION
This data type is a non-zero and non-negative value.
current

Objects

NameOIDSyntaxAccessStatus
ppc
OBJECT-IDENTITY
1.3.6.1.4.1.935
device
OBJECT-IDENTITY
1.3.6.1.4.1.935.10
matAgent
OBJECT-IDENTITY
1.3.6.1.4.1.935.10.2
matObjects
OBJECT-IDENTITY
1.3.6.1.4.1.935.10.2.1
matController
OBJECT-IDENTITY
1.3.6.1.4.1.935.10.2.1.1
matConSerialNum
OBJECT-TYPE
Controller serial number.
1.3.6.1.4.1.935.10.2.1.1.1DisplayString (SIZE(0..15))read-onlymandatory
matConName
OBJECT-TYPE
Power system name.
1.3.6.1.4.1.935.10.2.1.1.2DisplayString (SIZE(0..31))read-onlymandatory
matConWarningState
OBJECT-TYPE
The values indicate the unrestored traps. For example, if 'Controller Battery Low' and 'Controller temperature High' the agent send the trap 85 and trap 87 to NMS, so the value of matConWarningState should be '85,87'. And then the two events restored, the value of matConWarningState should change to empty.
1.3.6.1.4.1.935.10.2.1.1.3DisplayString (SIZE(0..31))read-onlymandatory
matConTemperature
OBJECT-TYPE
Temperature of the controller, the unit is 0.1 degree.
1.3.6.1.4.1.935.10.2.1.1.4INTEGERread-onlymandatory
matAgentSoftwareVerison
OBJECT-TYPE
The Network Management Card software/firmware version.
1.3.6.1.4.1.935.10.2.1.1.5DisplayString (SIZE(0..31))read-onlymandatory
matInverter
OBJECT-IDENTITY
1.3.6.1.4.1.935.10.2.1.2
matInvModuleNum
OBJECT-TYPE
The number of Inverter modules.
1.3.6.1.4.1.935.10.2.1.2.1INTEGERread-onlymandatory
matInvTable
OBJECT-TYPE
This table list Inverter message.
1.3.6.1.4.1.935.10.2.1.2.2not-accessiblemandatory
matInvEntry
OBJECT-TYPE
An entry containing information applicable to a particular Inverter module.
1.3.6.1.4.1.935.10.2.1.2.2.1not-accessiblemandatory
matInvModuleIndex
OBJECT-TYPE
The index of Inverter module.
1.3.6.1.4.1.935.10.2.1.2.2.1.1PositiveIntegernot-accessiblemandatory
matInvSerialNum
OBJECT-TYPE
Module serial number.
1.3.6.1.4.1.935.10.2.1.2.2.1.2DisplayString (SIZE(0..15))read-onlymandatory
matInvFirmwareVersion
OBJECT-TYPE
Firmware version.
1.3.6.1.4.1.935.10.2.1.2.2.1.3DisplayString (SIZE(0..7))read-onlymandatory
matInvHardwareVersion
OBJECT-TYPE
Hardware version.
1.3.6.1.4.1.935.10.2.1.2.2.1.4DisplayString (SIZE(0..7))read-onlymandatory
matInvWarningState
OBJECT-TYPE
The values indicate the unrestored traps. For example, if 'Inverter fault' and 'Inverter Over-loading' the agent send the trap 1 and trap 3 to NMS, so the value of matConWarningState should be '1,3'. And then the two events restored, the value of matConWarningState should change to empty.
1.3.6.1.4.1.935.10.2.1.2.2.1.5DisplayString (SIZE(0..63))read-onlymandatory
matInvOutputVoltage
OBJECT-TYPE
Inverter Output Voltage, the unit is 0.1 Volt.
1.3.6.1.4.1.935.10.2.1.2.2.1.6NonNegativeIntegerread-onlymandatory
matInvOutputCurrent
OBJECT-TYPE
Inverter Output Current, unit is 0.1 amp.
1.3.6.1.4.1.935.10.2.1.2.2.1.7NonNegativeIntegerread-onlymandatory
matInvBatteryVoltage
OBJECT-TYPE
Inverter Battery voltage, the unit is 0.1 Volt.
1.3.6.1.4.1.935.10.2.1.2.2.1.8NonNegativeIntegerread-onlymandatory
matInvOutputFreq
OBJECT-TYPE
Output frequency, the unit is 0.1 Hz.
1.3.6.1.4.1.935.10.2.1.2.2.1.9NonNegativeIntegerread-onlymandatory
matInvOutputPower
OBJECT-TYPE
Output power, the unit is VA.
1.3.6.1.4.1.935.10.2.1.2.2.1.10NonNegativeIntegerread-onlymandatory
matInvPowerLimit
OBJECT-TYPE
Power Limit Status of Inverter module, the unit is percent.
1.3.6.1.4.1.935.10.2.1.2.2.1.11NonNegativeIntegerread-onlymandatory
matInvRunTime
OBJECT-TYPE
Run time, the unit is Hour.
1.3.6.1.4.1.935.10.2.1.2.2.1.12NonNegativeIntegerread-onlymandatory
matInvTemperature
OBJECT-TYPE
Temperature of the inverter, the unit is 0.1 degree.
1.3.6.1.4.1.935.10.2.1.2.2.1.13INTEGERread-onlymandatory
matInvLineVoltage
OBJECT-TYPE
Line voltage of 3.5K, the unit is 0.1 Volt.
1.3.6.1.4.1.935.10.2.1.2.2.1.14NonNegativeIntegerread-onlymandatory
matInvLineFreq
OBJECT-TYPE
Line frequency of 3.5K, the unit is 0.1 Hz.
1.3.6.1.4.1.935.10.2.1.2.2.1.15NonNegativeIntegerread-onlymandatory
matInvMbsPosition
OBJECT-TYPE
MBS position of 3.5K.
1.3.6.1.4.1.935.10.2.1.2.2.1.16INTEGER {transfer(1), normal(2), bypass(3), invalid(4)}read-onlymandatory
matInvRunMode
OBJECT-TYPE
Currently run mode of 3.5K.
1.3.6.1.4.1.935.10.2.1.2.2.1.17INTEGER {powerOn(1), standby(2), bypass(3), line(4), battery(5), fault(6)}read-onlymandatory
matInvPriority
OBJECT-TYPE
Priority of 3.5K.
1.3.6.1.4.1.935.10.2.1.2.2.1.18INTEGER {batteryMode(1), lineMode(2)}read-onlymandatory
matConfInvOutputVoltage
OBJECT-TYPE
Rating Output voltage, the unit is 0.1 Volt.
1.3.6.1.4.1.935.10.2.1.2.2.1.19NonNegativeIntegerread-onlymandatory
matConfInvInputVoltage
OBJECT-TYPE
Rating Input voltage, the unit is 0.1 Volt.
1.3.6.1.4.1.935.10.2.1.2.2.1.20NonNegativeIntegerread-onlymandatory
matConfInvOutputVoltHighLoss
OBJECT-TYPE
Output High Loss voltage, the unit is 0.1 Volt.
1.3.6.1.4.1.935.10.2.1.2.2.1.21NonNegativeIntegerread-onlymandatory
matConfInvOutputVoltLowLoss
OBJECT-TYPE
Output Low loss voltage, the unit is 0.1 Volt.
1.3.6.1.4.1.935.10.2.1.2.2.1.22NonNegativeIntegerread-onlymandatory
matConfInvOutputPower
OBJECT-TYPE
Rating output power, the unit is VA.
1.3.6.1.4.1.935.10.2.1.2.2.1.23NonNegativeIntegerread-onlymandatory
matConfInvOutputFreq
OBJECT-TYPE
Rating output frequency, the unit is 0.1 Hz.
1.3.6.1.4.1.935.10.2.1.2.2.1.24NonNegativeIntegerread-onlymandatory
matInvPhaseType
OBJECT-TYPE
Phase type.
1.3.6.1.4.1.935.10.2.1.2.2.1.25INTEGER {singlePhase(1), threePhase(2)}read-onlymandatory
matInvOnOffStatus
OBJECT-TYPE
Inverter module On/Off status.
1.3.6.1.4.1.935.10.2.1.2.2.1.26INTEGER {shutdown(1), start(2)}read-writemandatory
matSts
OBJECT-IDENTITY
1.3.6.1.4.1.935.10.2.1.3
matStsModuleNum
OBJECT-TYPE
The number of STS modules.
1.3.6.1.4.1.935.10.2.1.3.1INTEGERread-onlymandatory
matStsTable
OBJECT-TYPE
This table list STS message.
1.3.6.1.4.1.935.10.2.1.3.2not-accessiblemandatory
matStsEntry
OBJECT-TYPE
An entry containing information applicable to a particular STS module.
1.3.6.1.4.1.935.10.2.1.3.2.1not-accessiblemandatory
matStsModuleIndex
OBJECT-TYPE
The index of STS module.
1.3.6.1.4.1.935.10.2.1.3.2.1.1PositiveIntegernot-accessiblemandatory
matStsModuleType
OBJECT-TYPE
Module type, 050 represent 50A, 100 represent 100A.
1.3.6.1.4.1.935.10.2.1.3.2.1.2DisplayString (SIZE(0..3))read-onlymandatory
matStsSerialNum
OBJECT-TYPE
Module serial number.
1.3.6.1.4.1.935.10.2.1.3.2.1.3DisplayString (SIZE(0..15))read-onlymandatory
matStsFirmwareVersion
OBJECT-TYPE
Firmware version.
1.3.6.1.4.1.935.10.2.1.3.2.1.4DisplayString (SIZE(0..7))read-onlymandatory
matStsHardwareVersion
OBJECT-TYPE
Hardware version.
1.3.6.1.4.1.935.10.2.1.3.2.1.5DisplayString (SIZE(0..7))read-onlymandatory
matStsWarningState
OBJECT-TYPE
The values indicate the unrestored traps. For example, if 'STS running in fault mode' and 'STS fan fault' the agent send the trap 59 and trap 61 to NMS, so the value of matConWarningState should be '59,61'. And then the two events restored, the value of matConWarningState should change to empty.
1.3.6.1.4.1.935.10.2.1.3.2.1.6DisplayString (SIZE(0..63))read-onlymandatory
matStsMainInputVoltage
OBJECT-TYPE
STS Mains I/P voltage, the unit is 0.1 Volts.
1.3.6.1.4.1.935.10.2.1.3.2.1.7NonNegativeIntegerread-onlymandatory
matStsMainInputFreq
OBJECT-TYPE
STS Mains I/P frequency, the unit is 0.1 Hz.
1.3.6.1.4.1.935.10.2.1.3.2.1.8NonNegativeIntegerread-onlymandatory
matStsInvInputVoltage
OBJECT-TYPE
STS INV I/P voltage, the unit is 0.1 volts.
1.3.6.1.4.1.935.10.2.1.3.2.1.9NonNegativeIntegerread-onlymandatory
matStsInvInputFreq
OBJECT-TYPE
STS INV I/P frequency, the unit is 0.1 Hz.
1.3.6.1.4.1.935.10.2.1.3.2.1.10NonNegativeIntegerread-onlymandatory
matStsOutputVoltage
OBJECT-TYPE
STS O/P voltage, the unit is 0.1 volts.
1.3.6.1.4.1.935.10.2.1.3.2.1.11NonNegativeIntegerread-onlymandatory
matStsOutputCurrent
OBJECT-TYPE
STS O/P Current, the unit is 0.1 amp.
1.3.6.1.4.1.935.10.2.1.3.2.1.12NonNegativeIntegerread-onlymandatory
matStsOutputPower
OBJECT-TYPE
STS O/P Power, the unit is VA.
1.3.6.1.4.1.935.10.2.1.3.2.1.13NonNegativeIntegerread-onlymandatory
matStsOutputFreq
OBJECT-TYPE
STS O/P frequency, the unit is 0.1 Hz.
1.3.6.1.4.1.935.10.2.1.3.2.1.14NonNegativeIntegerread-onlymandatory
matStsRuntime
OBJECT-TYPE
STS Runtime, the unit is Hour.
1.3.6.1.4.1.935.10.2.1.3.2.1.15NonNegativeIntegerread-onlymandatory
matStsTemperature
OBJECT-TYPE
STS module's Temperature, the unit is 0.1 degree.
1.3.6.1.4.1.935.10.2.1.3.2.1.16INTEGERread-onlymandatory
matStsMbsStatus
OBJECT-TYPE
STS MBS status.
1.3.6.1.4.1.935.10.2.1.3.2.1.17INTEGER {normalPosition(1), issPosition(2), ibpPosition(3), mssPosition(4), mbpPosition(5), mbsError(6)}read-onlymandatory
matStsStatus
OBJECT-TYPE
STS status.
1.3.6.1.4.1.935.10.2.1.3.2.1.18INTEGER {onLine(1), offLine(2)}read-onlymandatory
matStsRunningMode
OBJECT-TYPE
STS Running Mode.
1.3.6.1.4.1.935.10.2.1.3.2.1.19INTEGER {inverter(1), mains(2), noOutput(3)}read-onlymandatory
matStsMainHighLossVoltage
OBJECT-TYPE
STS Main high loss voltage, the unit is 0.1 volts.
1.3.6.1.4.1.935.10.2.1.3.2.1.20NonNegativeIntegerread-onlymandatory
matStsMainLowLossVoltage
OBJECT-TYPE
STS Main low loss voltag, the unit is 0.1 volts.
1.3.6.1.4.1.935.10.2.1.3.2.1.21NonNegativeIntegerread-onlymandatory
matStsInvHighLossVoltage
OBJECT-TYPE
STS Inverter high loss voltage, the unit is 0.1 volts.
1.3.6.1.4.1.935.10.2.1.3.2.1.22NonNegativeIntegerread-onlymandatory
matStsInvLosLossVoltage
OBJECT-TYPE
STS Inverter low loss voltage, the unit is 0.1 volts.
1.3.6.1.4.1.935.10.2.1.3.2.1.23NonNegativeIntegerread-onlymandatory
matDryContact
OBJECT-IDENTITY
1.3.6.1.4.1.935.10.2.1.4
matDryContactNum
OBJECT-TYPE
The number of dry contact.
1.3.6.1.4.1.935.10.2.1.4.1INTEGERread-onlymandatory
matDryContactTable
OBJECT-TYPE
This table list dry contact message.
1.3.6.1.4.1.935.10.2.1.4.2not-accessiblemandatory
matDryContactEntry
OBJECT-TYPE
An entry containing information of one dry contact.
1.3.6.1.4.1.935.10.2.1.4.2.1not-accessiblemandatory
matDryContactIndex
OBJECT-TYPE
The index of dry contact.
1.3.6.1.4.1.935.10.2.1.4.2.1.1PositiveIntegernot-accessiblemandatory
matDryContactString
OBJECT-TYPE
format: xx xx xx xx xx xx xx xx xx xx, xx: alarm code. If the configured alarm is less than 10, then fill the position with '--' to instead 'xx'. Alarm code: Inverter fault 0x01(for 3.5Kva system and 1.5Kva system), Inverter over load 0x02(for 3.5Kva system and 1.5Kva system), Inverter fan fault 0x03(for 3.5Kva system and 1.5Kva system), Inverter power limit 0x04(for 3.5Kva system and 1.5Kva system), Inverter DC input Abnormal 0x05(for 3.5Kva system and 1.5Kva system), Inverter low volt off 0x06(for 3.5Kva system and 1.5Kva system), Inverter lost 0x07(for 3.5Kva system and 1.5Kva system), Inverter Mains unavailable 0x19(for 3.5Kva system), Inverter Maintenance Bypass 0x1A(for 3.5Kva system), Inverter Output 0x1B(for 3.5Kva system), STS Inv unavailable 0x2A(for 1.5Kva system), STS Main unavailable 0x2B(for 1.5Kva system), STS Output overload 0x2C(for 1.5Kva system), STS OP Short circuit 0x2D(for 1.5Kva system), STS K1 Relay open 0x23(for 1.5Kva system), STS SCR1 short 0x24(for 1.5Kva system), STS SCR2 short 0x25(for 1.5Kva system), STS INV Bypass Mode 0x2F(for 1.5Kva system), STS Over temperature 0x30(for 1.5Kva system), STS MBS Abnormal 0x31(for 1.5Kva system), STS Fan Lock 0x27(for 1.5Kva system), STS Fault Mode 0x26(for 1.5Kva system), STS Eeprom Fault 0x28(for 1.5Kva system), SPS Power Fail 0x32(for 1.5Kva system), STS Output abnormal 0x34(for 1.5Kva system), STS Maintenance Bypass 0x35(for 1.5Kva system), STS Output 0x36(for 1.5Kva system), Controller temperature high 0x42(for 3.5Kva system and 1.5Kva system), Controller eeprom fail 0x43(for 3.5Kva system and 1.5Kva system), Controller CAN Bus Off 0x45(for 3.5Kva system and 1.5Kva system)
1.3.6.1.4.1.935.10.2.1.4.2.1.2DisplayString (SIZE(0..29))read-writemandatory
matConfig
OBJECT-IDENTITY
1.3.6.1.4.1.935.10.2.1.5
matConfInvSysOutputFreq
OBJECT-TYPE
Inverter system output frequency, can be 500 or 600, the unit is 0.1 Hz.
1.3.6.1.4.1.935.10.2.1.5.1NonNegativeIntegerread-writemandatory
matConfInvSysOutputVolt
OBJECT-TYPE
Inverter system output voltage, can be 1100, 1150,1200,2080,2200,2300,2400. The unit is 0.1 Volt.
1.3.6.1.4.1.935.10.2.1.5.2NonNegativeIntegerread-writemandatory
matConfInvSysOutputVoltHighLoss
OBJECT-TYPE
Output voltage high loss of Inverter System, the unit is 0.1 Volt. This value depends on matConfInvSysOutputVolt, the least significant digit must be zero, see table: matConfInvSysOutputVolt(0.1V) Range(0.1V) 1100 1170-1270, 1150 1220-1320, 1200 1270-1380, 2080 2200-2400, 2200 2330-2520, 2300 2440-2640, 2400 2540-2760
1.3.6.1.4.1.935.10.2.1.5.3NonNegativeIntegerread-writemandatory
matConfInvSysOutputVoltLowLoss
OBJECT-TYPE
Output Voltage Low Loss of inverter System, the unit is 0.1 volt. This value depends on matConfInvSysOutputVolt, the least significant digit must be zero, see table: matConfInvSysOutputVolt(0.1V) Range(0.1V) 1100 890-1050, 1150 930-1100, 1200 1000-1140, 2080 1760-1980, 2200 1760-2090, 2300 1850-2180, 2400 1930-2280
1.3.6.1.4.1.935.10.2.1.5.4NonNegativeIntegerread-writemandatory
matConfInvSysInputVolt
OBJECT-TYPE
Inverter System Input Voltage, the unit is 0.1 Volt. This value depends on matConfInvInputVoltage: matConfInvInputVoltage(0.1V)=480: Range(400-440), matConfInvInputVoltage(0.1V)=600: Range(500-550)
1.3.6.1.4.1.935.10.2.1.5.5NonNegativeIntegerread-writemandatory
matConfInvSysPowerLimit
OBJECT-TYPE
Inverter System Power Limited level, format: xxx, range: 50 to 100, the unit is percent.
1.3.6.1.4.1.935.10.2.1.5.6NonNegativeIntegerread-writemandatory
matConfInvSysLineVoltHighLoss
OBJECT-TYPE
High loss for line voltage of 3.5k inverter module, the unit is 0.1 volt. This value depends on matConfInvSysOutputVolt, the least significant digit must be zero, see table: matConfInvSysOutputVolt(0.1V) Range(0.1V) 2080 2180-2650, 2200 2300-2650, 2300 2400-2650, 2400 2500-2650
1.3.6.1.4.1.935.10.2.1.5.7NonNegativeIntegerread-writemandatory
matConfInvSysLineVoltLowLoss
OBJECT-TYPE
Low loss for line voltage of 3.5k inverter module, the unit is 0.1 volt. This value depends on matConfInvSysOutputVolt, the least significant digit must be zero, see table: matConfInvSysOutputVolt(0.1V) Range(0.1V) 2080 1850-1980, 2200 1850-2100, 2300 1850-2200, 2400 1850-2300
1.3.6.1.4.1.935.10.2.1.5.8NonNegativeIntegerread-writemandatory
matConfInvSysPriority
OBJECT-TYPE
Priority for 3.5K inverter module.
1.3.6.1.4.1.935.10.2.1.5.9INTEGER {batteryMode(1), lineMode(2)}read-writemandatory
matConfInvSysFanSpeed
OBJECT-TYPE
Inverter System fan speed.
1.3.6.1.4.1.935.10.2.1.5.10INTEGER {normalSpeed(1), fullSpeed(2)}read-writemandatory
matConfStsAcVoltHighLoss
OBJECT-TYPE
STS Module AC Voltage High Loss Volt, the unit is 0.1 volt. This value depends on matConfInvSysOutputVolt, the least significant digit must be zero, see table: matConfInvSysOutputVolt(0.1V) Range(0.1V) 1100 1170-1270, 1150 1220-1320, 1200 1270-1380, 2080 2200-2400, 2200 2330-2520, 2300 2440-2640, 2400 2540-2760
1.3.6.1.4.1.935.10.2.1.5.11NonNegativeIntegerread-writemandatory
matConfStsAcVoltLowLoss
OBJECT-TYPE
STS Module AC Voltage Low Loss Volt, the unit is 0.1 volt. This value depends on matConfInvSysOutputVolt, the least significant digit must be zero, see table: matConfInvSysOutputVolt(0.1V) Range(0.1V) 1100 890-1050, 1150 930-1100, 1200 1000-1140, 2080 1760-1980, 2200 1760-2090, 2300 1850-2180, 2400 1930-2280
1.3.6.1.4.1.935.10.2.1.5.12NonNegativeIntegerread-writemandatory
matConfStsIpvVoltHighLoss
OBJECT-TYPE
STS module Inverter IPV High Loss Volt, the unit is 0.1 volt. This value depends on matConfInvSysOutputVolt, the least significant digit must be zero, see table: matConfInvSysOutputVolt(0.1V) Range(0.1V) 1100 1170-1270, 1150 1220-1320, 1200 1270-1380, 2080 2200-2400, 2200 2330-2520, 2300 2440-2640, 2400 2540-2760
1.3.6.1.4.1.935.10.2.1.5.13NonNegativeIntegerread-writemandatory
matConfStsIpvVoltLowLoss
OBJECT-TYPE
STS module Inverter IPV low Loss Volt, the unit is 0.1 volt. This value depends on matConfInvSysOutputVolt, the least significant digit must be zero, see table: matConfInvSysOutputVolt(0.1V) Range(0.1V) 1100 890-1050, 1150 930-1100, 1200 1000-1140, 2080 1760-1980, 2200 1760-2090, 2300 1850-2180, 2400 1930-2280
1.3.6.1.4.1.935.10.2.1.5.14NonNegativeIntegerread-writemandatory
matConfStsPriority
OBJECT-TYPE
STS output priority.
1.3.6.1.4.1.935.10.2.1.5.15INTEGER {onLine(1), offLine(2)}read-writemandatory
matConfStsFanSpeed
OBJECT-TYPE
STS fan speed.
1.3.6.1.4.1.935.10.2.1.5.16INTEGER {normalSpeed(1), fullSpeed(2)}read-writemandatory
matTrapTargets
OBJECT-IDENTITY
1.3.6.1.4.1.935.10.2.1.6
matTrapTargetsNum
OBJECT-TYPE
The number of trap targets.
1.3.6.1.4.1.935.10.2.1.6.1INTEGERread-onlymandatory
matTrapTargetsTable
OBJECT-TYPE
This table list the managers'IP to send traps to.
1.3.6.1.4.1.935.10.2.1.6.2not-accessiblemandatory
matTrapTargetsEntry
OBJECT-TYPE
An entry containing information of one trap target.
1.3.6.1.4.1.935.10.2.1.6.2.1not-accessiblemandatory
matTrapTargetsIndex
OBJECT-TYPE
The index to a trap receiver entry
1.3.6.1.4.1.935.10.2.1.6.2.1.1PositiveIntegernot-accessiblemandatory
matTrapTargetsAddress
OBJECT-TYPE
The IP address of the manager to send a trap to.
1.3.6.1.4.1.935.10.2.1.6.2.1.2DisplayString (SIZE(0..45))read-writemandatory
matTrapTargetsCommunity
OBJECT-TYPE
The community name to use in the trap when sent to the manager.
1.3.6.1.4.1.935.10.2.1.6.2.1.3DisplayString (SIZE(0..31))read-writemandatory
matTrapType
OBJECT-TYPE
The type of trap to be received by the manager.
1.3.6.1.4.1.935.10.2.1.6.2.1.4INTEGER {none(1), matTrap(2)}read-writemandatory
matTrapSeverityLevel
OBJECT-TYPE
The severity level of traps to be received by this manager.
1.3.6.1.4.1.935.10.2.1.6.2.1.5INTEGER {observe(1), major(2), critical(3)}read-writemandatory
matTrapTargetsDesc
OBJECT-TYPE
Description of trap receivers
1.3.6.1.4.1.935.10.2.1.6.2.1.6DisplayString (SIZE(0..31))read-writemandatory
matTraps
OBJECT-IDENTITY
1.3.6.1.4.1.935.10.2.2

Notifications

NameOIDStatus
matInvFault
NOTIFICATION-TYPE
MAJOR: Inverter fault.
1.3.6.1.4.1.935.10.2.2.0.1
matReturnFromInvFault
NOTIFICATION-TYPE
OBSERVE: Return from Inverter fault.
1.3.6.1.4.1.935.10.2.2.0.2
matInvOverLoad
NOTIFICATION-TYPE
MAJOR: Inverter Over-loading.
1.3.6.1.4.1.935.10.2.2.0.3
matReturnFromInvOverLoad
NOTIFICATION-TYPE
OBSERVE: Return from Inverter Over-loading.
1.3.6.1.4.1.935.10.2.2.0.4
matInvFanFault
NOTIFICATION-TYPE
MAJOR: Inverter Fan fault.
1.3.6.1.4.1.935.10.2.2.0.5
matReturnFromInvFanFault
NOTIFICATION-TYPE
OBSERVE: Return from Inverter Fan fault.
1.3.6.1.4.1.935.10.2.2.0.6
matInvTempPowerLimit
NOTIFICATION-TYPE
MAJOR: Inverter power limit.
1.3.6.1.4.1.935.10.2.2.0.7
matReturnFromInvTempPowerLimit
NOTIFICATION-TYPE
OBSERVE: Return from Inverter power limit.
1.3.6.1.4.1.935.10.2.2.0.8
matInvInputAbnormal
NOTIFICATION-TYPE
MAJOR: Inverter input abnormal.
1.3.6.1.4.1.935.10.2.2.0.9
matReturnFromInvInputAbnormal
NOTIFICATION-TYPE
OBSERVEReturn from Inverter input abnormal.
1.3.6.1.4.1.935.10.2.2.0.10
matInvLowInputShutdown
NOTIFICATION-TYPE
MAJOR: Inverter shut down due to low input voltage.
1.3.6.1.4.1.935.10.2.2.0.11
matReturnFromInvLowInputShutdown
NOTIFICATION-TYPE
OBSERVE: Return from Inverter shut down due to low input voltage.
1.3.6.1.4.1.935.10.2.2.0.12
matInvNotRespond
NOTIFICATION-TYPE
CRITICAL: Inverter disconnected.
1.3.6.1.4.1.935.10.2.2.0.13
matReturnFromInvNotRespond
NOTIFICATION-TYPE
OBSERVE: Inverter connected.
1.3.6.1.4.1.935.10.2.2.0.14
matInvBusVoltageOverLimit
NOTIFICATION-TYPE
CRITICAL: Inverter Bus voltage over the maximal level.
1.3.6.1.4.1.935.10.2.2.0.15
matReturnFromInvBusVoltOverLimit
NOTIFICATION-TYPE
OBSERVE: Return from Inverter Bus voltage over the maximal level.
1.3.6.1.4.1.935.10.2.2.0.16
matInvBusVoltageUnderLimit
NOTIFICATION-TYPE
CRITICAL: Inverter Bus volt under the minimal level.
1.3.6.1.4.1.935.10.2.2.0.17
matReturnFromInvBusVoltUnderLimit
NOTIFICATION-TYPE
OBSERVE: Return from Inverter Bus volt under the minimal level.
1.3.6.1.4.1.935.10.2.2.0.18
matInvBusSoftFail
NOTIFICATION-TYPE
CRITICAL: Inverter Bus Soft Start Fail.
1.3.6.1.4.1.935.10.2.2.0.19
matReturnFromInvBusSoftFail
NOTIFICATION-TYPE
OBSERVE: Return from Inverter Bus Soft Start Fail.
1.3.6.1.4.1.935.10.2.2.0.20
matInvOutputShort
NOTIFICATION-TYPE
CRITICAL: Inverter Output Short.
1.3.6.1.4.1.935.10.2.2.0.21
matReturnFromInvOutputShort
NOTIFICATION-TYPE
OBSERVE: Return from Inverter Output Short.
1.3.6.1.4.1.935.10.2.2.0.22
matInvOutputVoltLow
NOTIFICATION-TYPE
CRITICAL: Inverter output voltage low.
1.3.6.1.4.1.935.10.2.2.0.23
matReturnFromInvOutputVoltLow
NOTIFICATION-TYPE
OBSERVE: Return from Inverter output voltage low.
1.3.6.1.4.1.935.10.2.2.0.24
matInvOutputVoltHigh
NOTIFICATION-TYPE
CRITICAL: Inverter output voltage high.
1.3.6.1.4.1.935.10.2.2.0.25
matReturnFromInvOutputVoltHigh
NOTIFICATION-TYPE
OBSERVE: Return from Inverter output voltage high.
1.3.6.1.4.1.935.10.2.2.0.26
matInvTemperatureHigh
NOTIFICATION-TYPE
CRITICAL: Inverter Temperature High.
1.3.6.1.4.1.935.10.2.2.0.27
matReturnFromInvTemperatureHigh
NOTIFICATION-TYPE
OBSERVE: Return from Inverter Temperature High.
1.3.6.1.4.1.935.10.2.2.0.28
matInvNegativePowerProtect
NOTIFICATION-TYPE
CRITICAL: Inverter negative power protection.
1.3.6.1.4.1.935.10.2.2.0.29
matReturnFromInvNegativePowerProtect
NOTIFICATION-TYPE
OBSERVE: Return from Inverter negative power protection.
1.3.6.1.4.1.935.10.2.2.0.30
matInvPulseFault
NOTIFICATION-TYPE
CRITICAL: Inverter Sync Pulse Fault.
1.3.6.1.4.1.935.10.2.2.0.31
matReturnFromInvPulseFault
NOTIFICATION-TYPE
OBSERVE: Return from Inverter Sync Pulse Fault.
1.3.6.1.4.1.935.10.2.2.0.32
matInvEPOShutdown
NOTIFICATION-TYPE
CRITICAL: Inverter EPO shutdown.
1.3.6.1.4.1.935.10.2.2.0.33
matReturnFromInvEPOShutdown
NOTIFICATION-TYPE
OBSERVE: Return from Inverter EPO shutdown.
1.3.6.1.4.1.935.10.2.2.0.34
matInvSoftStartFail
NOTIFICATION-TYPE
CRITICAL: Inverter soft start fail.
1.3.6.1.4.1.935.10.2.2.0.35
matReturnFromInvSoftStartFail
NOTIFICATION-TYPE
OBSERVE: Return from Inverter soft start fail.
1.3.6.1.4.1.935.10.2.2.0.36
matInvEEPROMFault
NOTIFICATION-TYPE
MAJOR: Inverter EEPROM fault.
1.3.6.1.4.1.935.10.2.2.0.37
matReturnFromInvEEPROMFault
NOTIFICATION-TYPE
OBSERVE: Return from Inverter EEPROM fault.
1.3.6.1.4.1.935.10.2.2.0.38
matInvBypassSCRShort
NOTIFICATION-TYPE
CRITICAL: Inverter Bypass SCR Short.
1.3.6.1.4.1.935.10.2.2.0.39
matReturnFromInvBypassSCRShort
NOTIFICATION-TYPE
OBSERVE: Return from Inverter Bypass SCR Short.
1.3.6.1.4.1.935.10.2.2.0.40
matInvMBSPosError
NOTIFICATION-TYPE
CRITICAL: Inverter MBS Position Error.
1.3.6.1.4.1.935.10.2.2.0.41
matReturnFromInvMBSPosError
NOTIFICATION-TYPE
OBSERVE: Return from Inverter MBS Position Error.
1.3.6.1.4.1.935.10.2.2.0.42
matInvBackfeedRelayOpen
NOTIFICATION-TYPE
CRITICAL: Inverter Backfeed Relay Open.
1.3.6.1.4.1.935.10.2.2.0.43
matReturnFromInvBackfeedRelayOpen
NOTIFICATION-TYPE
OBSERVE: Return from Inverter Backfeed Relay Open.
1.3.6.1.4.1.935.10.2.2.0.44
matInvHardwareError
NOTIFICATION-TYPE
CRITICAL: Inverter Hardware Detection Error.
1.3.6.1.4.1.935.10.2.2.0.45
matReturnFromInvHardwareError
NOTIFICATION-TYPE
OBSERVE: Return from Inverter Hardware Detection Error.
1.3.6.1.4.1.935.10.2.2.0.46
matInvMainUnavailable
NOTIFICATION-TYPE
MAJOR: Inverter Mains Unavailable.
1.3.6.1.4.1.935.10.2.2.0.47
matReturnFromInvMainUnavailable
NOTIFICATION-TYPE
OBSERVE: Return from Inverter Mains Unavailable.
1.3.6.1.4.1.935.10.2.2.0.48
matInvMaintenaceBypass
NOTIFICATION-TYPE
MAJOR: Inverter Maintenance Bypass.
1.3.6.1.4.1.935.10.2.2.0.49
matReturnFromInvMaintenaceBypass
NOTIFICATION-TYPE
OBSERVE: Return from Inverter Maintenance Bypass.
1.3.6.1.4.1.935.10.2.2.0.50
matStsBypassUnavailable
NOTIFICATION-TYPE
MAJOR: STS Bypass unavailable.
1.3.6.1.4.1.935.10.2.2.0.51
matReturnFromStsBypassUnavailable
NOTIFICATION-TYPE
OBSERVE: Return from STS Bypass unavailable.
1.3.6.1.4.1.935.10.2.2.0.52
matStsBackfeedRelayOpen
NOTIFICATION-TYPE
MAJOR: STS Back-feed relay open.
1.3.6.1.4.1.935.10.2.2.0.53
matReturnFromStsBackfeedRelayOpen
NOTIFICATION-TYPE
OBSERVE: Return from STS Back-feed relay open.
1.3.6.1.4.1.935.10.2.2.0.54
matStsScr1ShortCurcuit
NOTIFICATION-TYPE
CRITICAL: STS SCR1 short circuit.
1.3.6.1.4.1.935.10.2.2.0.55
matReturnFromStsScr1ShortCurcuit
NOTIFICATION-TYPE
OBSERVE: Return from STS SCR1 short circuit.
1.3.6.1.4.1.935.10.2.2.0.56
matStsScr2ShortCurcuit
NOTIFICATION-TYPE
CRITICAL: STS SCR2 short circuit.
1.3.6.1.4.1.935.10.2.2.0.57
matReturnFromStsScr2ShortCurcuit
NOTIFICATION-TYPE
OBSERVE: Return from STS SCR2 short circuit.
1.3.6.1.4.1.935.10.2.2.0.58
matStsFaultMode
NOTIFICATION-TYPE
CRITICAL: STS running in fault mode.
1.3.6.1.4.1.935.10.2.2.0.59
matReturnFromStsFaultMode
NOTIFICATION-TYPE
OBSERVE: Return from STS running in fault mode.
1.3.6.1.4.1.935.10.2.2.0.60
matStsFanFault
NOTIFICATION-TYPE
MAJOR: STS fan fault.
1.3.6.1.4.1.935.10.2.2.0.61
matReturnFromStsFanFault
NOTIFICATION-TYPE
OBSERVE: Return from STS fan fault.
1.3.6.1.4.1.935.10.2.2.0.62
matStsEEPROMFault
NOTIFICATION-TYPE
MAJOR: STS EEPROM fault.
1.3.6.1.4.1.935.10.2.2.0.63
matReturnFromStsEEPROMFault
NOTIFICATION-TYPE
OBSERVE: Return from STS EEPROM fault.
1.3.6.1.4.1.935.10.2.2.0.64
matStsInvFail
NOTIFICATION-TYPE
MAJOR: STS Inverter unavailable.
1.3.6.1.4.1.935.10.2.2.0.65
matReturnFromStsInvFail
NOTIFICATION-TYPE
OBSERVE: Return from STS Inverter unavailable.
1.3.6.1.4.1.935.10.2.2.0.66
matStsMainsFail
NOTIFICATION-TYPE
MAJOR: STS Mains unavailable.
1.3.6.1.4.1.935.10.2.2.0.67
matReturnFromStsMainFail
NOTIFICATION-TYPE
OBSERVE: Return from STS Mains unavailable.
1.3.6.1.4.1.935.10.2.2.0.68
matStsOverLoad
NOTIFICATION-TYPE
MAJOR: STS Output over load.
1.3.6.1.4.1.935.10.2.2.0.69
matReturnFromStsOverLoad
NOTIFICATION-TYPE
OBSERVE: Return from STS Output over load.
1.3.6.1.4.1.935.10.2.2.0.70
matStsOutputShortCircuit
NOTIFICATION-TYPE
CRITICAL: STS Output short circuit.
1.3.6.1.4.1.935.10.2.2.0.71
matReturnFromStsOutputShortCircuit
NOTIFICATION-TYPE
OBSERVE: Return from STS Output short circuit.
1.3.6.1.4.1.935.10.2.2.0.72
matStsInvBypassMode
NOTIFICATION-TYPE
CRITICAL: STS Inverter bypass mode.
1.3.6.1.4.1.935.10.2.2.0.73
matReturnFromStsInvBypassMode
NOTIFICATION-TYPE
OBSERVE: Return from STS Inverter bypass mode.
1.3.6.1.4.1.935.10.2.2.0.74
matStsTemperatureHigh
NOTIFICATION-TYPE
MAJOR: STS temperature high.
1.3.6.1.4.1.935.10.2.2.0.75
matReturnFromStsTemperatureHigh
NOTIFICATION-TYPE
OBSERVE: Return from STS temperature high.
1.3.6.1.4.1.935.10.2.2.0.76
matStsMBSPosFault
NOTIFICATION-TYPE
CRITICAL: STS MBS in abnormal position.
1.3.6.1.4.1.935.10.2.2.0.77
matReturnFromStsMBSPosFault
NOTIFICATION-TYPE
OBSERVE: Return from STS MBS in abnormal position.
1.3.6.1.4.1.935.10.2.2.0.78
matStsControlPowerFail
NOTIFICATION-TYPE
CRITICAL: STS Control power fail.
1.3.6.1.4.1.935.10.2.2.0.79
matReturnFromStsControlPowerFail
NOTIFICATION-TYPE
OBSERVE: Return from STS Control power fail.
1.3.6.1.4.1.935.10.2.2.0.80
matStsNotRespond
NOTIFICATION-TYPE
CRITICAL: STS disconnected.
1.3.6.1.4.1.935.10.2.2.0.81
matReturnFromStsNotRespond
NOTIFICATION-TYPE
OBSERVE: STS connected.
1.3.6.1.4.1.935.10.2.2.0.82
matStsOutputAbnormal
NOTIFICATION-TYPE
MAJOR: STS Output abnormal.
1.3.6.1.4.1.935.10.2.2.0.83
matReturnFromStsOutputAbnormal
NOTIFICATION-TYPE
OBSERVE: Return from STS Output abnormal.
1.3.6.1.4.1.935.10.2.2.0.84
matStsMaintenanceBypass
NOTIFICATION-TYPE
MAJOR: STS Maintenance Bypass.
1.3.6.1.4.1.935.10.2.2.0.85
matReturnFromStsMaintenanceBypass
NOTIFICATION-TYPE
OBSERVE: Return from STS Maintenance Bypass.
1.3.6.1.4.1.935.10.2.2.0.86
matConBatteryLow
NOTIFICATION-TYPE
CRITICAL: Controller Battery Low.
1.3.6.1.4.1.935.10.2.2.0.87
matReturnFromConBatteryLow
NOTIFICATION-TYPE
OBSERVE: Return from Controller Battery Low.
1.3.6.1.4.1.935.10.2.2.0.88
matConTemperatureHigh
NOTIFICATION-TYPE
CRITICAL: Controller temperature High.
1.3.6.1.4.1.935.10.2.2.0.89
matReturnFromConTemperatureHigh
NOTIFICATION-TYPE
OBSERVE: Return from Controller temperature High.
1.3.6.1.4.1.935.10.2.2.0.90
matConEEPROMFault
NOTIFICATION-TYPE
MAJOR: Controller EEPROM fault.
1.3.6.1.4.1.935.10.2.2.0.91
matReturnFromConEEPROMFault
NOTIFICATION-TYPE
OBSERVE: Return from Controller EEPROM fault.
1.3.6.1.4.1.935.10.2.2.0.92
matConBatteryVoltHigh
NOTIFICATION-TYPE
CRITICAL: Controller Battery voltage high.
1.3.6.1.4.1.935.10.2.2.0.93
matReturnFromConBatteryVoltHigh
NOTIFICATION-TYPE
OBSERVE: Return from Controller Battery voltage high.
1.3.6.1.4.1.935.10.2.2.0.94
matConCanBusOff
NOTIFICATION-TYPE
CRITICAL: Controller CAN bus off.
1.3.6.1.4.1.935.10.2.2.0.95
matReturnFromConCanBusOff
NOTIFICATION-TYPE
OBSERVE: Return from Controller CAN bus off.
1.3.6.1.4.1.935.10.2.2.0.96
matConCommunicationLost
NOTIFICATION-TYPE
CRITICAL: Controller communication lost.
1.3.6.1.4.1.935.10.2.2.0.97
matReturnFromCommunicationLost
NOTIFICATION-TYPE
OBSERVE: Return from Controller communication lost.
1.3.6.1.4.1.935.10.2.2.0.98