SWL2MGMT-MIB
- Registered at
- 1.3.6.1.4.1.2272.1.201.1.2
- Last updated
- 1900-07-15 00:00
- Organization
- enterprise, Inc.
- Namespace
- nortel
- Source file
SWL2MGMT-MIB- Digest
sha256:3a79a579eb6e09e9e269d7a84fa1740f9bb7bb573a3b7d468f8308f8f9a218f9
Description
The Structure of Layer 2 Network Management Information for the proprietary enterprise.
Contact
Customer Service Postal: Tel: E-mail:
Imports
| From | Symbols |
|---|---|
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP |
| SNMPv2-SMI | Counter32, Counter64, Gauge32, IpAddress, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TRAP-TYPE, TimeTicks, Unsigned32, iso |
| SNMPv2-TC | DisplayString, MacAddress, RowStatus, TEXTUAL-CONVENTION, TruthValue |
| SWPRIMGMT-MIB | privateMgmt |
Imported by
Nothing in this corpus imports this module.
Load order
Every file a consumer needs in order to load this module, dependencies first.
ATM-TC-MIB BGP4-MIB DIFFSERV-DSCP-TC DIFFSERV-MIB DVMRP-STD-MIB IANA-ADDRESS-FAMILY-NUMBERS-MIB IANA-RTPROTO-MIB IANAifType-MIB IEEE8021-SECY-MIB IF-MIB IGMP-STD-MIB INET-ADDRESS-MIB INTEGRATED-SERVICES-MIB IP-MIB IPMROUTE-STD-MIB IPV6-MIB IPV6-MLD-MIB IPV6-TC LLDP-MIB MPLS-TC-STD-MIB MSDP-MIB RADIUS-DYNAUTH-SERVER-MIB RAPID-CITY RFC1158-MIB RFC1271-MIB RMON-MIB RMON2-MIB SNMP-FRAMEWORK-MIB SNMPv2-CONF SNMPv2-MIB SNMPv2-SMI SNMPv2-TC SWL2MGMT-MIB SWPRIMGMT-MIB TOKEN-RING-RMON-MIB VRRP-MIB
Textual conventions
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| PortList type | ||||
| VlanIndex type |
Objects
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| swL2DevMgmt OBJECT-IDENTITY | 1.3.6.1.4.1.2272.1.201.1.2.1 | |||
| swL2DevInfo OBJECT-IDENTITY | 1.3.6.1.4.1.2272.1.201.1.2.1.1 | |||
| swDevInfoSystemUpTime OBJECT-TYPE The value of sysUpTime at the time the switch entered its current operational state. If the current state was entered prior to the last re-initialization, then this object contains a zero value. This value is in units of seconds. | 1.3.6.1.4.1.2272.1.201.1.2.1.1.1 | TimeTicks | read-only | current |
| swDevInfoTotalNumOfPort OBJECT-TYPE The number of ports within this switch. This value is the sum of the ports within this switch. | 1.3.6.1.4.1.2272.1.201.1.2.1.1.2 | INTEGER (0..65535) | read-only | current |
| swDevInfoNumOfPortInUse OBJECT-TYPE The number of ports in this switch connected to the segment or the end stations. | 1.3.6.1.4.1.2272.1.201.1.2.1.1.3 | INTEGER (0..65535) | read-only | current |
| swDevInfoConsoleInUse OBJECT-TYPE This usage indication of console system. | 1.3.6.1.4.1.2272.1.201.1.2.1.1.4 | INTEGER {other(1), in-use(2), not-in-use(3)} | read-only | current |
| swDevInfoFrontPanelLedStatus OBJECT-TYPE This object is a set of system LED indications. The first three octets is defined as system LED. The first LED is primary power LED. The second LED is redundant power LED. The third LED is console LED. The other octets following the second octets are the logical port LED (following dot1dBasePort ordering). Every two bytes are presented to a port. The first byte is presentd to the Link/Activity LED. The second byte is presented to the Speed LED. Link/Activity LED : The most significant bit is used for blink/solid: 8 = The LED blinks. The second significant bit is used for link status: 1 = link fail. 2 = link pass. Speed LED : 01 = 10Mbps. 02 = 100Mbps. 03 = 1000Mbps. The four remaining bits are currently unused and must be 0. | 1.3.6.1.4.1.2272.1.201.1.2.1.1.5 | OCTET STRING (SIZE(0..324)) | read-only | current |
| swL2DevCtrlUpDownloadState OBJECT-TYPE status of upload/download control. If the value is 'other', means never firmware updated since device started up. | 1.3.6.1.4.1.2272.1.201.1.2.1.1.6 | INTEGER {other(1), in-process(2), invalid-file(3), violation(4), file-not-found(5), disk-full(6), complete(7), time-out(8), tftp-establish-fail(9)} | read-only | current |
| swDevInfoSaveCfg OBJECT-TYPE This object indicates the status of the device configuration. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. proceeding(2) - the device configuration is saving into the NV-RAM. ready(3) ¡V the device configuration has been ready to save into NV-RAM. failed(4) - The processing of saving device configuration is failed. | 1.3.6.1.4.1.2272.1.201.1.2.1.1.7 | INTEGER {other(1), proceeding(2), ready(3), failed(4)} | read-only | current |
| swL2DevCtrl OBJECT-IDENTITY | 1.3.6.1.4.1.2272.1.201.1.2.1.2 | |||
| swL2DevCtrlStpState OBJECT-TYPE This object can be enabled or disabled spanning tree algorithm during runtime of the system. | 1.3.6.1.4.1.2272.1.201.1.2.1.2.1 | INTEGER {other(1), disabled(2), enabled(3)} | read-write | current |
| swL2DevCtrlIGMPSnooping OBJECT-TYPE This object indicates layer 2 Internet Group Management Protocol (IGMP) capture function is enabled or disabled. | 1.3.6.1.4.1.2272.1.201.1.2.1.2.2 | INTEGER {other(1), disabled(2), enabled(3)} | read-write | current |
| swL2DevCtrlRmonState OBJECT-TYPE This object can be enabled or disabled RMON. | 1.3.6.1.4.1.2272.1.201.1.2.1.2.3 | INTEGER {other(1), disabled(2), enabled(3)} | read-write | current |
| swL2DevCtrlUpDownloadImageFileName OBJECT-TYPE The name of the image file to be uploaded/Downloaded from the device to TFTP server when enabling image upload/download function (by writing swL2DevCtrlUpDownloadImage). | 1.3.6.1.4.1.2272.1.201.1.2.1.2.4 | DisplayString (SIZE(0..64)) | read-write | current |
| swL2DevCtrlUpDownloadImageSourceAddr OBJECT-TYPE The ip address where been uploaded/Downloaded image file. | 1.3.6.1.4.1.2272.1.201.1.2.1.2.5 | IpAddress | read-write | current |
| swL2DevCtrlUpDownloadImage OBJECT-TYPE Image file upload/download control. After setting, it will immediately invoke image upload/download function. While retrieving the value of this object, it always returns 'other' normally. | 1.3.6.1.4.1.2272.1.201.1.2.1.2.6 | INTEGER {other(1), upload(2), download(3)} | read-write | current |
| swL2DevCtrlSaveCfg OBJECT-TYPE As the object is set to active, the current device configuration is save into to NV-RAM.If set to normal, do nothing. | 1.3.6.1.4.1.2272.1.201.1.2.1.2.7 | INTEGER {normal(1), active(2)} | read-write | current |
| swL2DevCtrlCleanAllStatisticCounter OBJECT-TYPE As the object is set to active, all the statistic counters will be cleared. If set to normal, do nothing. | 1.3.6.1.4.1.2272.1.201.1.2.1.2.8 | INTEGER {normal(1), active(2)} | read-write | current |
| swL2DevCtrlStpForwardBPDU OBJECT-TYPE This object allow the forwarding of STP BPDU packets from other network device or not when STP is disabled on the device. | 1.3.6.1.4.1.2272.1.201.1.2.1.2.9 | INTEGER {other(1), disabled(2), enabled(3)} | read-write | current |
| swL2DevAlarm OBJECT-IDENTITY | 1.3.6.1.4.1.2272.1.201.1.2.1.3 | |||
| swL2DevAlarmNewRoot OBJECT-TYPE When the device has become the new root of the Spanning Tree, this object decide whether to send a new root trap. | 1.3.6.1.4.1.2272.1.201.1.2.1.3.1 | INTEGER {other(1), disabled(2), enabled(3)} | read-write | current |
| swL2DevAlarmTopologyChange OBJECT-TYPE This object determine to send a trap or not when the switch topology was changed. If the object is enabled(3), the topologyChange trap is sent by the device when any of its configured ports transitions from the Learning state to the Forwarding state, or from the Forwarding state to the Blocking state. For the same port tranition, the device doesn't send the trap if this object value is disabled or other. | 1.3.6.1.4.1.2272.1.201.1.2.1.3.2 | INTEGER {other(1), disabled(2), enabled(3)} | read-write | current |
| swL2DevAlarmLinkChange OBJECT-TYPE This object determine to send a trap or not when the link was changed. If the object is enabled(3), the Link Change trap is sent by the device when any of its ports link change. The device doesn't send the trap if this object value is disabled or other. | 1.3.6.1.4.1.2272.1.201.1.2.1.3.3 | INTEGER {other(1), disabled(2), enabled(3)} | read-write | current |
| swL2UnitMgmt OBJECT-IDENTITY | 1.3.6.1.4.1.2272.1.201.1.2.2 | |||
| swL2UnitCtrl OBJECT-IDENTITY | 1.3.6.1.4.1.2272.1.201.1.2.2.1 | |||
| swL2ModuleMgmt OBJECT-IDENTITY | 1.3.6.1.4.1.2272.1.201.1.2.3 | |||
| swL2PortMgmt OBJECT-IDENTITY | 1.3.6.1.4.1.2272.1.201.1.2.4 | |||
| swL2PortInfoTable OBJECT-TYPE A table that contains information about every port. | 1.3.6.1.4.1.2272.1.201.1.2.4.1 | not-accessible | current | |
| swL2PortInfoEntry OBJECT-TYPE A list of information for each port of the device. | 1.3.6.1.4.1.2272.1.201.1.2.4.1.1 | not-accessible | current | |
| swL2PortInfoPortIndex OBJECT-TYPE This object indicates the module's port number.(1..Max port number in the module) | 1.3.6.1.4.1.2272.1.201.1.2.4.1.1.1 | INTEGER (0..65535) | read-only | current |
| swL2PortInfoUnitIndex OBJECT-TYPE Indicates ID of the unit in the device | 1.3.6.1.4.1.2272.1.201.1.2.4.1.1.2 | INTEGER (0..65535) | read-only | current |
| swL2PortInfoType OBJECT-TYPE This object indicates the connector type of this port. | 1.3.6.1.4.1.2272.1.201.1.2.4.1.1.3 | INTEGER {other(1), portType-100Base-TX(2), portType-100Base-FX(3), portType-100Base-FL(4), portType-1000Base-T(5), portType-1000Base-SX(6), portType-1000Base-LX(7), portType-1000Base-GBIC-SX(8), portType-1000Base-GBIC-LX(9), portType-1000Base-GBIC-CWDM(10), portType-1000Base-GBIC-XD(11), portType-1000Base-GBIC-ZX(12), portType-1000Base-GBIC-COPPER(13), portType-1000Base-GBIC-OTHER(14)} | read-only | current |
| swL2PortInfoLinkStatus OBJECT-TYPE This object indicates the port link status. | 1.3.6.1.4.1.2272.1.201.1.2.4.1.1.4 | INTEGER {other(1), link-pass(2), link-fail(3)} | read-only | current |
| swL2PortInfoNwayStatus OBJECT-TYPE This object indicates the port speed and duplex mode. | 1.3.6.1.4.1.2272.1.201.1.2.4.1.1.5 | INTEGER {other(1), auto(2), half-10Mbps(3), full-10Mbps(4), half-100Mbps(5), full-100Mbps(6), half-1Gigabps(7), full-1Gigabps(8)} | read-only | current |
| swL2PortCtrlTable OBJECT-TYPE A table that contains control information about every port. | 1.3.6.1.4.1.2272.1.201.1.2.4.2 | not-accessible | current | |
| swL2PortCtrlEntry OBJECT-TYPE A list of control information for each port of the device. | 1.3.6.1.4.1.2272.1.201.1.2.4.2.1 | not-accessible | current | |
| swL2PortCtrlPortIndex OBJECT-TYPE This object indicates the module's port number.(1..Max port number in the module) | 1.3.6.1.4.1.2272.1.201.1.2.4.2.1.1 | INTEGER (0..65535) | read-only | current |
| swL2PortCtrlUnitIndex OBJECT-TYPE Indicates ID of the unit in the device | 1.3.6.1.4.1.2272.1.201.1.2.4.2.1.2 | INTEGER (0..65535) | read-only | current |
| swL2PortCtrlAdminState OBJECT-TYPE This object decide the port enabled or disabled. | 1.3.6.1.4.1.2272.1.201.1.2.4.2.1.3 | INTEGER {other(1), disabled(2), enabled(3)} | read-write | current |
| swL2PortCtrlNwayState OBJECT-TYPE Chose the port speed, duplex mode, and N-Way function mode. | 1.3.6.1.4.1.2272.1.201.1.2.4.2.1.4 | INTEGER {other(1), nway-enabled(2), nway-disabled-10Mbps-Half(3), nway-disabled-10Mbps-Full(4), nway-disabled-100Mbps-Half(5), nway-disabled-100Mbps-Full(6), nway-disabled-1Gigabps-Full(7)} | read-write | current |
| swL2PortCtrlFlowCtrlState OBJECT-TYPE The flow control mechanism is different between full duplex mode and half duplex mode. For half duplex mode, the jamming signal is asserted. For full duplex mode, IEEE 802.3x flow control function sends PAUSE frames and receives PAUSE frames. | 1.3.6.1.4.1.2272.1.201.1.2.4.2.1.5 | INTEGER {other(1), disabled(2), enabled(3)} | read-write | current |
| swL2PortCtrlAddressLearningState OBJECT-TYPE This object decide the address learning state on this port is enabled or disabled. | 1.3.6.1.4.1.2272.1.201.1.2.4.2.1.6 | INTEGER {other(1), disabled(2), enabled(3)} | read-write | current |
| swL2PortUtilTable OBJECT-TYPE A table that contains information of utilization about every port. | 1.3.6.1.4.1.2272.1.201.1.2.4.3 | not-accessible | current | |
| swL2PortUtilEntry OBJECT-TYPE A list of information of utilization for each port of the device. | 1.3.6.1.4.1.2272.1.201.1.2.4.3.1 | not-accessible | current | |
| swL2PortUtilPortIndex OBJECT-TYPE This object indicates the module's port number.(1..Max port number in the module) | 1.3.6.1.4.1.2272.1.201.1.2.4.3.1.1 | INTEGER (0..65535) | read-only | current |
| swL2PortUtilTxSec OBJECT-TYPE Indicates how many packets transmitted per second. | 1.3.6.1.4.1.2272.1.201.1.2.4.3.1.2 | Gauge32 | read-only | current |
| swL2PortUtilRxSec OBJECT-TYPE Indicates how many packets received per second. | 1.3.6.1.4.1.2272.1.201.1.2.4.3.1.3 | Gauge32 | read-only | current |
| swL2PortUtilUtilization OBJECT-TYPE This object indicates the port utilization. | 1.3.6.1.4.1.2272.1.201.1.2.4.3.1.4 | INTEGER (0..100) | read-only | current |
| swL2FilterMgmt OBJECT-IDENTITY | 1.3.6.1.4.1.2272.1.201.1.2.6 | |||
| swL2FilterAddrConfig OBJECT-IDENTITY | 1.3.6.1.4.1.2272.1.201.1.2.6.1 | |||
| swL2FilterAddrMaxSupportedEntries OBJECT-TYPE Maximum number of entries in the MAC address filtering table (swL2FilterAddrCtrlTable). | 1.3.6.1.4.1.2272.1.201.1.2.6.1.1 | INTEGER (0..65535) | read-only | current |
| swL2FilterAddrCurrentTotalEntries OBJECT-TYPE Current applied number of entries in the MAC address filtering table. | 1.3.6.1.4.1.2272.1.201.1.2.6.1.2 | INTEGER (0..65535) | read-only | current |
| swL2FilterAddrCtrlTable OBJECT-TYPE This table defines information for the device to filter packets with specific MAC address (either as the DA and/or as the SA). The MAC address can be a unicast address or a multicast address. This table has higher priority than both static FDB table and IGMP table. It means that if a MAC address appears on this table also appears on the static FDB table, the device will use the information provide by this table to process the packet. | 1.3.6.1.4.1.2272.1.201.1.2.6.1.3 | not-accessible | current | |
| swL2FilterAddrCtrlEntry OBJECT-TYPE A list of information about a specific unicast/multicast MAC address for which the switch has filtering information. | 1.3.6.1.4.1.2272.1.201.1.2.6.1.3.1 | not-accessible | current | |
| swL2FilterAddrMacIndex OBJECT-TYPE This object indicates a unicast/multicast MAC address for which the switch has filtering information. But if the swL2FilterAddrState = src-addr then the object can not be a multicast MAC address. | 1.3.6.1.4.1.2272.1.201.1.2.6.1.3.1.1 | MacAddress | read-only | current |
| swL2FilterAddrState OBJECT-TYPE This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. dst-addr(2) - recieved frames's destination address are currently used to be filtered as it meets with the MAC address entry of the table. src-addr(3) - recieved frames's source address are currently used to be filtered as it meets with the MAC address entry of the table. dst-src-addr(4) - recieved frames's destination address or source address are currently used to be filtered as it meets with the MAC address entry of the table. invalid(5) - writing this value to the object, and then the corresponding entry will be removed from the table. | 1.3.6.1.4.1.2272.1.201.1.2.6.1.3.1.2 | INTEGER {other(1), dst-addr(2), src-addr(3), dst-src-addr(4), invalid(5)} | read-write | current |
| swL2VlanMgmt OBJECT-IDENTITY | 1.3.6.1.4.1.2272.1.201.1.2.7 | |||
| swL2StaticVlanTable OBJECT-TYPE A table containing static configuration information for each VLAN configured into the device by (local or network) management. | 1.3.6.1.4.1.2272.1.201.1.2.7.1 | not-accessible | current | |
| swL2StaticVlanEntry OBJECT-TYPE Static information for a VLAN configured into the device by (local or network) management. | 1.3.6.1.4.1.2272.1.201.1.2.7.1.1 | not-accessible | current | |
| swL2StaticVlanIndex OBJECT-TYPE A value that uniquely identifies the Virtual LAN associated with this entry. | 1.3.6.1.4.1.2272.1.201.1.2.7.1.1.1 | INTEGER (1..4094) | read-only | current |
| swL2StaticVlanName OBJECT-TYPE An administratively-assigned name for this VLAN. | 1.3.6.1.4.1.2272.1.201.1.2.7.1.1.2 | DisplayString (SIZE(1..32)) | read-write | current |
| swL2StaticVlanType OBJECT-TYPE The type of VLAN, distinguished according to the policy used to define its port membership. | 1.3.6.1.4.1.2272.1.201.1.2.7.1.1.3 | INTEGER {byport(1), byIpSubnet(2), byProtocolId(3)} | read-write | current |
| swL2StaticVlanProtocolId OBJECT-TYPE The protocol identifier of this VLAN. This value is meaningful only if swL2StaticVlanType is equal to byProtocolId(3). For other VLAN types it should have the value none(0). | 1.3.6.1.4.1.2272.1.201.1.2.7.1.1.4 | INTEGER {none(0), ipEther2(1), rarpEther2(2), ipx802dot3(3), ipx802dot2(4), ipxSnap(5), ipxEther2(6), apltkEther2Snap(7), decEther2(8), decOtherEther2(9), sna802dot2(10), snaEther2(11), netBios(12), xnsEther2(13), vinesEther2(14), ipv6Ether2(15), userDefined(16), arpEther2(17)} | read-write | current |
| swL2StaticVlanIpSubnetAddr OBJECT-TYPE The IP subnet address of this VLAN. This value is meaningful only if rcVlanType is equal to byIpSubnet(2). For other VLAN types it should have the value 0.0.0.0. | 1.3.6.1.4.1.2272.1.201.1.2.7.1.1.5 | IpAddress | read-write | current |
| swL2StaticVlanIpSubnetMask OBJECT-TYPE The IP subnet mask of this VLAN. This value is meaningful only if rcVlanType is equal to byIpSubnet(2). For other VLAN types it should have the value 0.0.0.0. | 1.3.6.1.4.1.2272.1.201.1.2.7.1.1.6 | IpAddress | read-write | current |
| swL2StaticVlanUserDefinedPid OBJECT-TYPE When swL2StaticVlanProtocolId is set to userDefined(16) in a protocol-based VLAN, this field represents the 16-bit user defined protocol identifier. Otherwise, this object should be zero. | 1.3.6.1.4.1.2272.1.201.1.2.7.1.1.7 | OCTET STRING (SIZE(0..2)) | read-write | current |
| swL2StaticVlanEncap OBJECT-TYPE This value is meaningful only if swL2StaticVlanProtocolId is set to userDefined(16). Otherwise, this object should be un-used(5). If If this set to ethernet2(2), the Detagged Frame uses Type-encapsulated 802.3 format. If this set to llc(3), the Detagged Frame contains both a DSAP and an SSAP address field in the positions. If this set to snap(4), the Detagged Frame is of the format specified by IEEE Std. 802.1H for the encoding of an IEEE 802.3 Type Field in an 802.2/SNAP header. | 1.3.6.1.4.1.2272.1.201.1.2.7.1.1.8 | INTEGER {all(1), ethernet2(2), llc(3), snap(4), un-used(5)} | read-write | current |
| swL2StaticVlanUserPriority OBJECT-TYPE User priority level. This value is meaningful only if swL2StaticVlanType is set to byIpSubnet(2) or byProtocolId(3). | 1.3.6.1.4.1.2272.1.201.1.2.7.1.1.9 | INTEGER (0 | 4 | 6 | 7) | read-write | current |
| swL2StaticVlanEgressPorts OBJECT-TYPE The set of ports which are permanently assigned to the egress list for this VLAN by management. The default value of this object is a string of zeros of appropriate length. | 1.3.6.1.4.1.2272.1.201.1.2.7.1.1.10 | PortList | read-write | current |
| swL2StaticVlanUntaggedPorts OBJECT-TYPE The set of ports which should transmit egress packets for this VLAN as untagged. The default value of this object for the default VLAN is a string of appropriate length including all ports. There is no specified default for other VLANs. | 1.3.6.1.4.1.2272.1.201.1.2.7.1.1.11 | PortList | read-write | current |
| swL2StaticVlanStatus OBJECT-TYPE This object indicates the status of this entry. | 1.3.6.1.4.1.2272.1.201.1.2.7.1.1.12 | RowStatus | read-write | current |
| swL2StaticVlanIpSubnetArpClassId OBJECT-TYPE This object indicates the ARP classification ID. If the swL2StaticVlanType is not byIpSubnet(2), this value must be 0. If the swL2StaticVlanType is byIpSubnet(2), the range of this object is 1 to 4094. This object is useful when create the first IpSubnet entry, and not allow to modify. | 1.3.6.1.4.1.2272.1.201.1.2.7.1.1.13 | INTEGER (0..4094) | read-write | current |
| swL2VlanPortTable OBJECT-TYPE A table containing per port control and status information for VLAN configuration in the device. | 1.3.6.1.4.1.2272.1.201.1.2.7.2 | not-accessible | current | |
| swL2VlanPortEntry OBJECT-TYPE Information controlling VLAN configuration for a port on the device. | 1.3.6.1.4.1.2272.1.201.1.2.7.2.1 | not-accessible | current | |
| swL2VlanPortIndex OBJECT-TYPE An unique index used to identify a particular port in the system. | 1.3.6.1.4.1.2272.1.201.1.2.7.2.1.1 | INTEGER | read-only | current |
| swL2VlanPortPvid OBJECT-TYPE The PVID, the VLAN ID assigned to untagged frames or Priority- Tagged frames received on this port. | 1.3.6.1.4.1.2272.1.201.1.2.7.2.1.2 | INTEGER | read-only | current |
| swL2VlanPortIngressChecking OBJECT-TYPE When this is enabled(3) the device will discard incoming frames for VLANs which do not include this Port in its Member set. When disabled(2), the port will accept all incoming frames. | 1.3.6.1.4.1.2272.1.201.1.2.7.2.1.3 | INTEGER {other(1), disabled(2), enabled(3)} | read-write | current |
| swL2TrunkMgmt OBJECT-IDENTITY | 1.3.6.1.4.1.2272.1.201.1.2.8 | |||
| swL2TrunkMaxSupportedEntries OBJECT-TYPE Maximum number of entries in the trunk configuration table (swL2TrunkCtrlTable). | 1.3.6.1.4.1.2272.1.201.1.2.8.1 | INTEGER (0..65535) | read-only | current |
| swL2TrunkCurrentNumEntries OBJECT-TYPE Current actived number of entries in the trunk configuration table. | 1.3.6.1.4.1.2272.1.201.1.2.8.2 | INTEGER (0..65535) | read-only | current |
| swL2TrunkCtrlTable OBJECT-TYPE This table specifys which ports group a set of ports(up to 8) into a single logical link. | 1.3.6.1.4.1.2272.1.201.1.2.8.3 | not-accessible | current | |
| swL2TrunkCtrlEntry OBJECT-TYPE A list of information specifies which ports group a set of ports(up to 8) into a single logical link. | 1.3.6.1.4.1.2272.1.201.1.2.8.3.1 | not-accessible | current | |
| swL2TrunkIndex OBJECT-TYPE The index of logical port trunk. The trunk group number depend on the existence of unit and module. | 1.3.6.1.4.1.2272.1.201.1.2.8.3.1.1 | INTEGER (0..65535) | read-only | current |
| swL2TrunkName OBJECT-TYPE The name of logical port trunk. | 1.3.6.1.4.1.2272.1.201.1.2.8.3.1.2 | DisplayString (SIZE(0..12)) | read-write | current |
| swL2TrunkMasterPort OBJECT-TYPE The object indicates the master port number of the port trunk entry. When using Port Trunk, you can not configure the other ports of the group except the master port. Their configuration must be same as the master port (e.g. speed, duplex, enabled/disabled, flow control, and so on). | 1.3.6.1.4.1.2272.1.201.1.2.8.3.1.3 | INTEGER (1..65535) | read-write | current |
| swL2TrunkMember OBJECT-TYPE Indicate how many number of ports is included in this Trunk. The trunk port number depend on the existence of module. The maximum number of ports is 4 for one trunks. | 1.3.6.1.4.1.2272.1.201.1.2.8.3.1.4 | PortList | read-write | current |
| swL2TrunkFloodingPort OBJECT-TYPE The object indicates the flooding port number of the port trunk entry. The first port of the trunk is implicitly configured to be the flooding port. | 1.3.6.1.4.1.2272.1.201.1.2.8.3.1.5 | INTEGER (1..65535) | read-only | current |
| swL2TrunkState OBJECT-TYPE This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disabled(2) - the port trunk disabled. enabled(3) - the port trunk enabled. invalid(4) - writing this value to the object, and then the corresponding entry will be removed from the table. | 1.3.6.1.4.1.2272.1.201.1.2.8.3.1.6 | INTEGER {other(1), disabled(2), enabled(3), invalid(4)} | read-write | current |
| swL2TrunkBPDU8600InterState OBJECT-TYPE This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disabled(2) - the trunk member doesn't send BPDU. enabled(3) - the trunk member can send BPDU. | 1.3.6.1.4.1.2272.1.201.1.2.8.3.1.7 | INTEGER {other(1), disabled(2), enabled(3)} | read-write | current |
| swL2TrunkAlgorithm OBJECT-TYPE This object configures to part of the packet examined by the switch when selecting the egress port for transmitting load-sharing data. This feature is only available using the address-based load-sharing algorithm. | 1.3.6.1.4.1.2272.1.201.1.2.8.4 | INTEGER {other(1), mac-source(2), mac-destination(3), mac-source-dest(4), ip-source(5), ip-destination(6), ip-source-dest(7)} | read-write | current |
| swL2MirrorMgmt OBJECT-IDENTITY | 1.3.6.1.4.1.2272.1.201.1.2.9 | |||
| swL2MirrorLogicTargetPort OBJECT-TYPE This object indicates switch which port will sniff another port. A trunk port member cannot be configured as a target Snooping port. The port number is the sequential (logical) number which is also applied to bridge MIB, etc. | 1.3.6.1.4.1.2272.1.201.1.2.9.1 | INTEGER (0..65535) | read-write | current |
| swL2MirrorPortSourceIngress OBJECT-TYPE The represent the ingress into the source port packet to sniffed. | 1.3.6.1.4.1.2272.1.201.1.2.9.2 | PortList | read-write | current |
| swL2MirrorPortSourceEgress OBJECT-TYPE The represent the egress from the source port packet to sniffed. | 1.3.6.1.4.1.2272.1.201.1.2.9.3 | PortList | read-write | current |
| swL2MirrorPortState OBJECT-TYPE This object indicates the port mirroring state. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disabled(2) - writing this value to the object, and then the corresponding entry will be removed from the table. enabled(3) - this entry is reside in the table. | 1.3.6.1.4.1.2272.1.201.1.2.9.4 | INTEGER {other(1), disabled(2), enabled(3)} | read-write | current |
| swL2IGMPMgmt OBJECT-IDENTITY | 1.3.6.1.4.1.2272.1.201.1.2.10 | |||
| swL2IGMPMaxSupportedVlans OBJECT-TYPE Maximum number of Vlans in the layer 2 IGMP control table (swL2IGMPCtrlTable). | 1.3.6.1.4.1.2272.1.201.1.2.10.1 | INTEGER (0..65535) | read-only | current |
| swL2IGMPMaxIpGroupNumPerVlan OBJECT-TYPE Maximum number of multicast ip group per Vlan in the layer 2 IGMP information table (swL2IGMPQueryInfoTable). | 1.3.6.1.4.1.2272.1.201.1.2.10.2 | INTEGER (0..65535) | read-only | current |
| swL2IGMPCtrlTable OBJECT-TYPE The table controls the Vlan's IGMP function. Its scale depends on current VLAN state (swL2VlanInfoStatus). If VLAN is disabled mode, there is only one entry in the table, with index 1. If VLAN is in Port-Base or 802.1q mode, the number of entries can be up to 12, with index range from 1 to 12. | 1.3.6.1.4.1.2272.1.201.1.2.10.3 | not-accessible | current | |
| swL2IGMPCtrlEntry OBJECT-TYPE The entry in IGMP control table (swL2IGMPCtrlTable). The entry is effective only when IGMP capture switch (swL2DevCtrlIGMPSnooping) is enabled. | 1.3.6.1.4.1.2272.1.201.1.2.10.3.1 | not-accessible | current | |
| swL2IGMPCtrlVid OBJECT-TYPE This object indicates the IGMP control entry's VLAN id. If VLAN is disabled, the Vid is always 0 and cannot be changed by management users. If VLAN is in Port-Base mode, the Vid is arranged from 1 to 12, fixed form. If VLAN is in 802.1q mode, the Vid setting can vary from 1 to 4094 by management user, and the Vid in each entry must be unique in the IGMP Control Table. | 1.3.6.1.4.1.2272.1.201.1.2.10.3.1.1 | INTEGER (0..65535) | read-only | current |
| swL2IGMPQueryInterval OBJECT-TYPE The frequency at which IGMP Host-Query packets are transmitted on this switch. | 1.3.6.1.4.1.2272.1.201.1.2.10.3.1.2 | INTEGER (1..65535) | read-write | current |
| swL2IGMPMaxResponseTime OBJECT-TYPE The maximum query response time on this switch. | 1.3.6.1.4.1.2272.1.201.1.2.10.3.1.3 | INTEGER (1..25) | read-write | current |
| swL2IGMPRobustness OBJECT-TYPE The Robustness Variable allows tuning for the expected packet loss on a subnet. If a subnet is expected to be lossy, the Robustness Variable may be increased. IGMP is robust to (Robustness Variable-1) packet losses. | 1.3.6.1.4.1.2272.1.201.1.2.10.3.1.4 | INTEGER (1..255) | read-write | current |
| swL2IGMPLastMemberQueryInterval OBJECT-TYPE The Last Member Query Interval is the Max Response Time inserted into Group-Specific Queries sent in response to Leave Group messages, and is also the amount of time between Group-Specific Query messages. | 1.3.6.1.4.1.2272.1.201.1.2.10.3.1.5 | INTEGER (1..65535) | read-write | current |
| swL2IGMPHostTimeout OBJECT-TYPE The timer value for sending IGMP query packet when none was sent by the host in the LAN. The timer works in per-VLAN basis. Our device will be activated to send the query message if the timer is expired. Please reference RFC2236-1997. | 1.3.6.1.4.1.2272.1.201.1.2.10.3.1.6 | INTEGER (1..16711450) | read-write | current |
| swL2IGMPRouteTimeout OBJECT-TYPE The Router Timeout is how long a host must wait after hearing a Query before it may send any IGMPv2 messages. | 1.3.6.1.4.1.2272.1.201.1.2.10.3.1.7 | INTEGER (1..16711450) | read-write | current |
| swL2IGMPLeaveTimer OBJECT-TYPE When a querier receives a Leave Group message for a group that has group members on the reception interface, it sends Group-Specific Queries every swL2IGMPLeaveTimer to the group being left. | 1.3.6.1.4.1.2272.1.201.1.2.10.3.1.8 | INTEGER (1..16711450) | read-write | current |
| swL2IGMPQueryState OBJECT-TYPE This object decide the IGMP query enabled or disabled. | 1.3.6.1.4.1.2272.1.201.1.2.10.3.1.9 | INTEGER {other(1), disabled(2), enabled(3)} | read-write | current |
| swL2IGMPCurrentState OBJECT-TYPE This object indicates the current IGMP query state. | 1.3.6.1.4.1.2272.1.201.1.2.10.3.1.10 | INTEGER {other(1), querier(2), non-querier(3)} | read-only | current |
| swL2IGMPCtrlState OBJECT-TYPE This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disabled(2) - IGMP funtion is disabled for this entry. enabled(3) - IGMP funtion is enabled for this entry. | 1.3.6.1.4.1.2272.1.201.1.2.10.3.1.11 | INTEGER {other(1), disabled(2), enabled(3)} | read-write | current |
| swL2IGMPQueryInfoTable OBJECT-TYPE The table contains the number current IGMP query packets which is captured by this device, as well as the IGMP query packets sent by the device. | 1.3.6.1.4.1.2272.1.201.1.2.10.4 | not-accessible | current | |
| swL2IGMPQueryInfoEntry OBJECT-TYPE Information about current IGMP query information, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrState of associated VLAN entry are all enabled. | 1.3.6.1.4.1.2272.1.201.1.2.10.4.1 | not-accessible | current | |
| swL2IGMPInfoVid OBJECT-TYPE This object indicates the Vid of associated IGMP info table entry. It follows swL2IGMPCtrlVid in the associated entry of IGMP control table (swL2IGMPCtrlTable). | 1.3.6.1.4.1.2272.1.201.1.2.10.4.1.1 | INTEGER (0..65535) | read-only | current |
| swL2IGMPInfoQueryCount OBJECT-TYPE This object indicates the number of query packets received since the IGMP function enabled, in per-VLAN basis. | 1.3.6.1.4.1.2272.1.201.1.2.10.4.1.2 | INTEGER (0..65535) | read-only | current |
| swL2IGMPInfoTxQueryCount OBJECT-TYPE This object indicates the send count of IGMP query messages, in per-VLAN basis. In case of IGMP timer expiration, the switch sends IGMP query packets to related VLAN member ports and increment this object by 1. | 1.3.6.1.4.1.2272.1.201.1.2.10.4.1.3 | INTEGER (0..65535) | read-only | current |
| swL2IGMPGroupTable OBJECT-TYPE The table containing current IGMP information which captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated VLAN entry are all enabled. Note that the priority of IGMP table entries is lower than Filtering Table, i.e. if there is a table hash collision between the entries of IGMP Table and Filtering Table inside the switch H/W address table, then Filtering Table entry overwrite the colliding entry of IGMP Table. See swL2FilterMgmt description also. | 1.3.6.1.4.1.2272.1.201.1.2.10.5 | not-accessible | current | |
| swL2IGMPGroupEntry OBJECT-TYPE Information about current IGMP information which captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated VLAN entry are all enabled. | 1.3.6.1.4.1.2272.1.201.1.2.10.5.1 | not-accessible | current | |
| swL2IGMPVid OBJECT-TYPE This object indicates the Vid of individual IGMP table entry. It shows the Vid of IGMP report information captured on network. | 1.3.6.1.4.1.2272.1.201.1.2.10.5.1.1 | INTEGER (0..65535) | read-only | current |
| swL2IGMPGroupIpAddr OBJECT-TYPE This object is identify group ip address which is captured from IGMP packet, in per-Vlan basis. | 1.3.6.1.4.1.2272.1.201.1.2.10.5.1.2 | IpAddress | read-only | current |
| swL2IGMPMacAddr OBJECT-TYPE This object is identify mac address which is corresponding to swL2IGMPGroupIpAddr, in per-Vlan basis. | 1.3.6.1.4.1.2272.1.201.1.2.10.5.1.3 | MacAddress | read-only | current |
| swL2IGMPPortMap OBJECT-TYPE This object indicates which ports are belong to the same multicast group, in per-Vlan basis. Each multicast group has a octect string to indicate with port map. The most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the switch is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'(Note that the setting of the bit corresponding to the port from which a frame is received is irrelevant). The 4 octets is represent one unit port according its logic port. If the unit less 32 port, the other port don't care just fill zero. | 1.3.6.1.4.1.2272.1.201.1.2.10.5.1.4 | PortList | read-only | current |
| swL2IGMPIpGroupReportCount OBJECT-TYPE This object indicate how much report packet was receive by our device corresponding with this entry from IGMP function enabled, in per-Vlan basis. | 1.3.6.1.4.1.2272.1.201.1.2.10.5.1.5 | INTEGER (0..65535) | read-only | current |
| swL2IGMPForwardTable OBJECT-TYPE The table containing current IGMP forwarding information which captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated VLAN entry are all enabled. Note that the priority of IGMP table entries is lower than Filtering Table, i.e. if there is a table hash collision between the entries of IGMP Table and Filtering Table inside the switch H/W address table, then Filtering Table entry overwrite the colliding entry of IGMP Table. See swL2FilterMgmt description also. | 1.3.6.1.4.1.2272.1.201.1.2.10.6 | not-accessible | current | |
| swL2IGMPForwardEntry OBJECT-TYPE Information about current IGMP forwarding information which captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated VLAN entry are all enabled. | 1.3.6.1.4.1.2272.1.201.1.2.10.6.1 | not-accessible | current | |
| swL2IGMPForwardVid OBJECT-TYPE This object indicates the Vid of individual IGMP table entry. It shows the Vid of IGMP report forward information captured on network. | 1.3.6.1.4.1.2272.1.201.1.2.10.6.1.1 | INTEGER (0..65535) | read-only | current |
| swL2IGMPForwardGroupIpAddr OBJECT-TYPE This object is identify group ip address which is captured from IGMP packet, in per-Vlan basis. | 1.3.6.1.4.1.2272.1.201.1.2.10.6.1.2 | IpAddress | read-only | current |
| swL2IGMPForwardPortMap OBJECT-TYPE This object indicates which ports are belong to the same multicast group, in per-Vlan basis. Each multicast group has a octect string to indicate with port map. The most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the switch is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'(Note that the setting of the bit corresponding to the port from which a frame is received is irrelevant). The 4 octets is represent one unit port according its logic port. If the unit less 32 port, the other port don't care just fill zero. | 1.3.6.1.4.1.2272.1.201.1.2.10.6.1.3 | PortList | read-only | current |
| swL2IGMPRPTable OBJECT-TYPE The table allows you to designate a range of ports as being connected to multicast-enabled routers. This will ensure that all packets with such a router as its destination will reach the multicast-enabled router, regardless of protocol, etc. | 1.3.6.1.4.1.2272.1.201.1.2.10.7 | not-accessible | current | |
| swL2IGMPRPEntry OBJECT-TYPE A list of swL2IGMPRPTable. | 1.3.6.1.4.1.2272.1.201.1.2.10.7.1 | not-accessible | current | |
| swL2IGMPRPVid OBJECT-TYPE The Vid of the VLAN on which the router port resides. | 1.3.6.1.4.1.2272.1.201.1.2.10.7.1.1 | INTEGER (0..65535) | read-only | current |
| swL2IGMPRPStaticRouterPort OBJECT-TYPE Specifies a range of ports which will be configured as router ports. | 1.3.6.1.4.1.2272.1.201.1.2.10.7.1.2 | PortList | read-write | current |
| swL2IGMPRPDynamicRouterPort OBJECT-TYPE Displays router ports that have been dynamically configued. | 1.3.6.1.4.1.2272.1.201.1.2.10.7.1.3 | PortList | read-only | current |
| swL2IGMPMulticastRouterOnly OBJECT-TYPE This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disabled(2) - the switch forwards all mulitcast traffic to any IP router. enabled(3) - the switch will forward all multicast traffic to the multicast router, only. | 1.3.6.1.4.1.2272.1.201.1.2.10.8 | INTEGER {other(1), disabled(2), enabled(3)} | read-write | current |
| swL2IGMPGroupPortTable OBJECT-TYPE This table describe the detail information of the member ports of the swL2IGMPGroupTable. | 1.3.6.1.4.1.2272.1.201.1.2.10.9 | not-accessible | current | |
| swL2IGMPGroupPortEntry OBJECT-TYPE Information about member ports of current swL2IGMPGroupTable. | 1.3.6.1.4.1.2272.1.201.1.2.10.9.1 | not-accessible | current | |
| swL2IGMPPortMember OBJECT-TYPE This object indicates which ports are belong to the same multicast group, in per-Vlan basis, in swL2IGMPGroupTable. | 1.3.6.1.4.1.2272.1.201.1.2.10.9.1.1 | INTEGER (0..65535) | read-only | current |
| swL2IGMPPortAgingTime OBJECT-TYPE This object indicate the aging out timer. This value is in units of seconds. | 1.3.6.1.4.1.2272.1.201.1.2.10.9.1.2 | INTEGER (1..16711450) | read-only | current |
| swL2IGMPMulticastFilter OBJECT-TYPE This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disabled(2) - the un-registered multicast traffic will be flooded. enabled(3) - the un-registered multicast traffic will be filtered. | 1.3.6.1.4.1.2272.1.201.1.2.10.10 | INTEGER {other(1), disabled(2), enabled(3)} | read-write | current |
| swL2TrafficMgmt OBJECT-IDENTITY | 1.3.6.1.4.1.2272.1.201.1.2.12 | |||
| swL2TrafficCtrlTable OBJECT-TYPE This table specifys the storm traffic control configuration. | 1.3.6.1.4.1.2272.1.201.1.2.12.1 | not-accessible | current | |
| swL2TrafficCtrlEntry OBJECT-TYPE A list of information specifies the storm traffic control configuration. | 1.3.6.1.4.1.2272.1.201.1.2.12.1.1 | not-accessible | current | |
| swL2TrafficCtrlGroupIndex OBJECT-TYPE The index of logical port trunk. The trunk group number depend on the existence of unit and module. | 1.3.6.1.4.1.2272.1.201.1.2.12.1.1.1 | INTEGER (0..65535) | read-only | current |
| swL2TrafficCtrlUnitIndex OBJECT-TYPE Indicates ID of the unit in the device | 1.3.6.1.4.1.2272.1.201.1.2.12.1.1.2 | INTEGER (0..65535) | read-only | current |
| swL2TrafficCtrlBMStormthreshold OBJECT-TYPE This object to decide how much thousand packets per second broadcast/multicast (depend on swL2TrafficCtrlBcastStormCtrl, swL2TrafficCtrlMcastStormCtrl or swL2TrafficCtrlDlfStormCtrl objects whether is enabled) will active storm control. Whenever a port reaches its configured amount of packets in the one second time interval, the device will start dropping that type of packet, until the time interval has expired. Once the time interval has expired, the device will start forwarding that type of packet. | 1.3.6.1.4.1.2272.1.201.1.2.12.1.1.3 | INTEGER (0..255) | read-write | current |
| swL2TrafficCtrlBcastStormCtrl OBJECT-TYPE This object indicates broadcast storm control function is enabled or disabled. | 1.3.6.1.4.1.2272.1.201.1.2.12.1.1.4 | INTEGER {other(1), disabled(2), enabled(3)} | read-write | current |
| swL2TrafficCtrlMcastStormCtrl OBJECT-TYPE This object indicates multicast storm control function is enabled or disabled. | 1.3.6.1.4.1.2272.1.201.1.2.12.1.1.5 | INTEGER {other(1), disabled(2), enabled(3)} | read-write | current |
| swL2TrafficCtrlDlfStormCtrl OBJECT-TYPE This object indicates destination lookup fail function is enabled or disabled. | 1.3.6.1.4.1.2272.1.201.1.2.12.1.1.6 | INTEGER {other(1), disabled(2), enabled(3)} | read-write | current |
| swL2QosMgmt OBJECT-IDENTITY | 1.3.6.1.4.1.2272.1.201.1.2.13 | |||
| swL2QosSchedulingTable OBJECT-TYPE The switch contains 4 hardware priority queues. Incoming packets must be mapped to one of these four queues. Each hardware queue will transmit all of the packets in its buffer before allowing the next lower priority queue to transmit its packets. When the lowest hardware priority queue has finished transmitting all of its packets, the highest hardware priority queue can again transmit any packets it may have received. | 1.3.6.1.4.1.2272.1.201.1.2.13.1 | not-accessible | current | |
| swL2QosSchedulingEntry OBJECT-TYPE A list of information specifies the Qos output scheduling Table. | 1.3.6.1.4.1.2272.1.201.1.2.13.1.1 | not-accessible | current | |
| swL2QosSchedulingClassId OBJECT-TYPE This specifies which of the four hardware priority queues. The four hardware priority queues are identified by number, from 0 to 3, with the 0 queue being the lowest priority. | 1.3.6.1.4.1.2272.1.201.1.2.13.1.1.1 | INTEGER (0..3) | read-only | current |
| swL2QosSchedulingMaxPkts OBJECT-TYPE Specifies the maximium number of packets the above specified hardware priority queue will be allowed to transmit before allowing the next lowest priority queue to transmit its packets. | 1.3.6.1.4.1.2272.1.201.1.2.13.1.1.2 | INTEGER (0..255) | read-write | current |
| swL2QosSchedulingMaxLatency OBJECT-TYPE Specifies the maximum amount of time the above specified hardware priority queue will be allowed to transmit packets before allowing the next lowest hardware priority queue to begin transmitting its packets. A value between 0 and 255 can be specified. With this value multiplied by 16 ms to arrive at the total allowed time for the queue to transmit packets. | 1.3.6.1.4.1.2272.1.201.1.2.13.1.1.3 | INTEGER (0..255) | read-write | current |
| swL2QosPriorityTable OBJECT-TYPE This table display the current priority settings on the switch. | 1.3.6.1.4.1.2272.1.201.1.2.13.2 | not-accessible | current | |
| swL2QosPriorityEntry OBJECT-TYPE A list of information display the current priority settings on the switch. | 1.3.6.1.4.1.2272.1.201.1.2.13.2.1 | not-accessible | current | |
| swL2QosPriorityType OBJECT-TYPE These parameters define what characteristics an incoming packet must meet. One or more of the above parameters must be defined. | 1.3.6.1.4.1.2272.1.201.1.2.13.2.1.1 | INTEGER {other(1), type-dscp(2), type-8021p(3), type-tcp(4), type-udp(5), type-ip(6), type-mac(7)} | read-only | current |
| swL2QosPriorityValue OBJECT-TYPE This object must match with swL2QosPriorityType. If the type is type-dscp(2), the range of this object is 0~63. If the type is type-8021p(3), the range of this object is 0~7. If the type is type-tcp(4) or type-udp(5), the range of this object is 1~65535. | 1.3.6.1.4.1.2272.1.201.1.2.13.2.1.2 | OCTET STRING (SIZE(1 | 2 | 4 | 6)) | read-only | current |
| swL2QosPriorityPriority OBJECT-TYPE Allows to specify a priority value to be written to the 802.1p priority field of an incoming packet that meets the criteria. | 1.3.6.1.4.1.2272.1.201.1.2.13.2.1.3 | INTEGER (0..7) | read-write | current |
| swL2QosPriorityPriorityState OBJECT-TYPE This object indicates 802.1p priority function is enabled or disabled. | 1.3.6.1.4.1.2272.1.201.1.2.13.2.1.4 | INTEGER {other(1), disabled(2), enabled(3)} | read-write | current |
| swL2QosPriorityReplaceDscp OBJECT-TYPE Allows to specify a value to be written to the DSCP field of an incoming packet that meets the criteria. | 1.3.6.1.4.1.2272.1.201.1.2.13.2.1.5 | INTEGER (0..63) | read-write | current |
| swL2QosPriorityReplaceDscpState OBJECT-TYPE This object indicates DSCP function is enabled or disabled. | 1.3.6.1.4.1.2272.1.201.1.2.13.2.1.6 | INTEGER {other(1), disabled(2), enabled(3)} | read-write | current |
| swL2QosPriorityReplacePriority OBJECT-TYPE This object indicates the 802.1p user priority with the priority specified above will be replaced or not. | 1.3.6.1.4.1.2272.1.201.1.2.13.2.1.7 | INTEGER {other(1), disabled(2), enabled(3)} | read-write | current |
| swL2QosPriorityState OBJECT-TYPE This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry is reside in the table. | 1.3.6.1.4.1.2272.1.201.1.2.13.2.1.8 | INTEGER {other(1), invalid(2), valid(3)} | read-write | current |
| swL2MgmtMIBTraps OBJECT-IDENTITY | 1.3.6.1.4.1.2272.1.201.1.2.14 | |||
| swL2StormCtrlMgmt OBJECT-IDENTITY | 1.3.6.1.4.1.2272.1.201.1.2.15 | |||
| swL2StormCtrlTable OBJECT-TYPE This table specifys the storm traffic control configuration. | 1.3.6.1.4.1.2272.1.201.1.2.15.1 | not-accessible | current | |
| swL2StormCtrlEntry OBJECT-TYPE A list of information specifies the storm traffic control configuration. | 1.3.6.1.4.1.2272.1.201.1.2.15.1.1 | not-accessible | current | |
| swL2StormCtrlPortIndex OBJECT-TYPE The index of logical port. | 1.3.6.1.4.1.2272.1.201.1.2.15.1.1.1 | INTEGER (0..65535) | read-only | current |
| swL2StormCtrlBcastStormCtrl OBJECT-TYPE This object indicates broadcast storm control function is enabled or disabled. | 1.3.6.1.4.1.2272.1.201.1.2.15.1.1.2 | INTEGER {other(1), disabled(2), enabled(3)} | read-write | current |
| swL2StormCtrlMcastStormCtrl OBJECT-TYPE This object indicates multicast storm control function is enabled or disabled. | 1.3.6.1.4.1.2272.1.201.1.2.15.1.1.3 | INTEGER {other(1), disabled(2), enabled(3)} | read-write | current |
| swL2StormCtrlBMStormThreshold OBJECT-TYPE This object to decide how much percentage packets per second broadcast/multicast (depend on swL2StormCtrlBcastStormCtrl or swL2StormCtrlMcastStormCtrl objects whether is enabled) will active storm control. Whenever a port reaches its configured percent of packets in the one second time interval, the device will start dropping that type of packet, until the time interval has expired. Once the time interval has expired, the device will start forwarding that type of packet. | 1.3.6.1.4.1.2272.1.201.1.2.15.1.1.4 | INTEGER (0..100) | read-write | current |
| swL2StormCtrlDlfState OBJECT-TYPE This object indicates destination lookup fail function is enabled or disabled. | 1.3.6.1.4.1.2272.1.201.1.2.15.2 | INTEGER {other(1), disabled(2), enabled(3)} | read-write | current |
| swL2StormCtrlDlfThreshold OBJECT-TYPE This object to decide how much packets per second destination lookup fail (depend on swL2StormCtrlDlfState objects whether is enabled) will active storm control. Whenever the device reaches its configured packets in the one second time interval, the device will start dropping that type of packet, until the time interval has expired. Once the time interval has expired, the device will start forwarding that type of packet. This value must be the multiples of 8192. | 1.3.6.1.4.1.2272.1.201.1.2.15.3 | INTEGER (0..148810) | read-write | current |
| swL2CpuRateLimitTable OBJECT-TYPE This table specifys the CPU rate limit per port. Once too much broadcast/multicast traffic, exceed CP-Limit, comes in from a port, the port state will be disabled. | 1.3.6.1.4.1.2272.1.201.1.2.15.4 | not-accessible | current | |
| swL2CpuRateLimitEntry OBJECT-TYPE A list of information specifies the CPU rate limit of the port configuration. | 1.3.6.1.4.1.2272.1.201.1.2.15.4.1 | not-accessible | current | |
| swL2CpuRateLimitPortIndex OBJECT-TYPE The index of logical port. | 1.3.6.1.4.1.2272.1.201.1.2.15.4.1.1 | INTEGER (0..65535) | read-only | current |
| swL2CpuRateLimitState OBJECT-TYPE This object indicates CPU rate limit function is enabled or disabled. | 1.3.6.1.4.1.2272.1.201.1.2.15.4.1.2 | INTEGER {other(1), disabled(2), enabled(3)} | read-write | current |
| swL2CpuRateLimitBcastThreshold OBJECT-TYPE This object to decide how much packets per second broadcast will active traffic control. Whenever a port reaches its configured packets in the one second time interval, the port will be disabled. | 1.3.6.1.4.1.2272.1.201.1.2.15.4.1.3 | INTEGER (0..1700) | read-write | current |
| swL2CpuRateLimitMcastThreshold OBJECT-TYPE This object to decide how much packets per second multicast will active traffic control. Whenever a port reaches its configured packets in the one second time interval, the port will be disabled. | 1.3.6.1.4.1.2272.1.201.1.2.15.4.1.4 | INTEGER (0..2000) | read-write | current |
| swL2CpuUtilization OBJECT-TYPE The utilization of CPU. | 1.3.6.1.4.1.2272.1.201.1.2.15.5 | INTEGER (0..100) | read-only | current |
| swL2ACLQosMgmt OBJECT-IDENTITY | 1.3.6.1.4.1.2272.1.201.1.2.16 | |||
| swL2ACLQosTemplate1Mode OBJECT-TYPE This object decide the operate mode of template_1. | 1.3.6.1.4.1.2272.1.201.1.2.16.1 | INTEGER {other(1), security(2), qos(3), l4-switch(4)} | read-write | current |
| swL2ACLQosTemplate2Mode OBJECT-TYPE This object decide the operate mode of template_2. | 1.3.6.1.4.1.2272.1.201.1.2.16.2 | INTEGER {other(1), security(2), qos(3), l4-switch(4)} | read-write | current |
| swL2ACLQosFlowClassifierTable OBJECT-TYPE This table specifys the template of flow classifier. | 1.3.6.1.4.1.2272.1.201.1.2.16.3 | not-accessible | current | |
| swL2ACLQosFlowClassifierEntry OBJECT-TYPE A list of information specifies the template of flow classifier. | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1 | not-accessible | current | |
| swL2ACLQosFlowClassifierTemplateId OBJECT-TYPE The index of template ID. | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.1 | INTEGER (0..65535) | read-only | current |
| swL2ACLQosFlowClassifierCurrentMode OBJECT-TYPE The current operated mode of this template. | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.2 | INTEGER {other(1), security(2), qos(3), l4-switch(4)} | read-only | current |
| swL2ACLQosFlowClassifierSecuritySrcMask OBJECT-TYPE This object indicates a source IP subnet rule for the switch. If the swL2ACLQosFlowClassifierCurrentMode is not security(2), then this object must be 0.0.0.0. | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.3 | IpAddress | read-write | current |
| swL2ACLQosFlowClassifierQosFlavor OBJECT-TYPE These parameters define what characteristics an incoming packet must meet. One or more of the above parameters must be defined. If the swL2ACLQosFlowClassifierCurrentMode is not qos(3), then this object must be flavor-un-used(6). | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.4 | INTEGER {flavor-8021p(1), flavor-dscp(2), flavor-ip(3), flavor-tcp(4), flavor-udp(5), flavor-un-used(6)} | read-write | current |
| swL2ACLQosFlowClassifierL4SwitchTCPDstIp OBJECT-TYPE This object indicate the destination ipaddress in the configured L4 TCP-session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3). | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.5 | INTEGER {true(1), false(2), un-used(3)} | read-write | current |
| swL2ACLQosFlowClassifierL4SwitchTCPSrcIp OBJECT-TYPE This object indicate the source ipaddress in the configured L4 TCP-session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3). | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.6 | INTEGER {true(1), false(2), un-used(3)} | read-write | current |
| swL2ACLQosFlowClassifierL4SwitchTCPTos OBJECT-TYPE This object indicate the type of service in the configured L4 TCP-session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3). | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.7 | INTEGER {true(1), false(2), un-used(3)} | read-write | current |
| swL2ACLQosFlowClassifierL4SwitchTCPDstPort OBJECT-TYPE This object indicate the destination TCP port number in the configured L4 TCP-session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3). | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.8 | INTEGER {true(1), false(2), un-used(3)} | read-write | current |
| swL2ACLQosFlowClassifierL4SwitchTCPSrcPort OBJECT-TYPE This object indicate the source TCP port number in the configured L4 TCP-session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3). | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.9 | INTEGER {true(1), false(2), un-used(3)} | read-write | current |
| swL2ACLQosFlowClassifierL4SwitchTCPFlags OBJECT-TYPE This object indicate the TCP flags in the configured L4 TCP- session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3). | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.10 | INTEGER {true(1), false(2), un-used(3)} | read-write | current |
| swL2ACLQosFlowClassifierL4SwitchUDPDstIp OBJECT-TYPE This object indicate the destination ipaddress in the configured L4 UDP-session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3). | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.11 | INTEGER {true(1), false(2), un-used(3)} | read-write | current |
| swL2ACLQosFlowClassifierL4SwitchUDPSrcIp OBJECT-TYPE This object indicate the source ipaddress in the configured L4 UDP-session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3). | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.12 | INTEGER {true(1), false(2), un-used(3)} | read-write | current |
| swL2ACLQosFlowClassifierL4SwitchUDPTos OBJECT-TYPE This object indicate the type of service in the configured L4 UDP-session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3). | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.13 | INTEGER {true(1), false(2), un-used(3)} | read-write | current |
| swL2ACLQosFlowClassifierL4SwitchUDPDstPort OBJECT-TYPE This object indicate the destination UDP port number in the configured L4 UDP session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3). | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.14 | INTEGER {true(1), false(2), un-used(3)} | read-write | current |
| swL2ACLQosFlowClassifierL4SwitchUDPSrcPort OBJECT-TYPE This object indicate the source UDP port number in the configured L4 UDP session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3). | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.15 | INTEGER {true(1), false(2), un-used(3)} | read-write | current |
| swL2ACLQosFlowClassifierL4SwitchOtherDstIp OBJECT-TYPE This object indicate the destination ipaddress in the configured L4 OTHER-session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3). | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.16 | INTEGER {true(1), false(2), un-used(3)} | read-write | current |
| swL2ACLQosFlowClassifierL4SwitchOtherSrcIp OBJECT-TYPE This object indicate the source ipaddress in the configured L4 OTHER-session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3). | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.17 | INTEGER {true(1), false(2), un-used(3)} | read-write | current |
| swL2ACLQosFlowClassifierL4SwitchOtherTos OBJECT-TYPE This object indicate the type of service in the configured L4 OTHER-session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3). | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.18 | INTEGER {true(1), false(2), un-used(3)} | read-write | current |
| swL2ACLQosFlowClassifierL4SwitchOtherL4Protocol OBJECT-TYPE This object indicate the l4_protocol in the configured L4 OTHER-session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3). | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.19 | INTEGER {true(1), false(2), un-used(3)} | read-write | current |
| swL2ACLQosFlowClassifierL4SwitchOtherICMPMessage OBJECT-TYPE This object indicate the ICMP message in the configured L4 OTHER-session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3). | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.20 | INTEGER {true(1), false(2), un-used(3)} | read-write | current |
| swL2ACLQosFlowClassifierL4SwitchOtherIGMPType OBJECT-TYPE This object indicate the IGMP type in the configured L4 OTHER-session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3). | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.21 | INTEGER {true(1), false(2), un-used(3)} | read-write | current |
| swL2ACLQosFlowClassifierActiveRuleNumber OBJECT-TYPE This object indicates the number of active rule. | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.22 | INTEGER (0..65535) | read-only | current |
| swL2ACLQosFlowClassifierSecurityDstMask OBJECT-TYPE This object indicates a destination IP subnet rule for the switch. If the swL2ACLQosFlowClassifierCurrentMode is not security(2), then this object must be 0.0.0.0. | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.23 | IpAddress | read-write | current |
| swL2ACLQosFlowClassifierVlanTable OBJECT-TYPE This table specifys which vlan has been binded in the template. | 1.3.6.1.4.1.2272.1.201.1.2.16.4 | not-accessible | current | |
| swL2ACLQosFlowClassifierVlanEntry OBJECT-TYPE A list of information which vlan has been binded in the template. | 1.3.6.1.4.1.2272.1.201.1.2.16.4.1 | not-accessible | current | |
| swL2ACLQosFlowClassifierVlanTemplateId OBJECT-TYPE The index of template ID. | 1.3.6.1.4.1.2272.1.201.1.2.16.4.1.1 | INTEGER (0..65535) | read-only | current |
| swL2ACLQosFlowClassifierVlanVlanName OBJECT-TYPE The existence of VLAN name. | 1.3.6.1.4.1.2272.1.201.1.2.16.4.1.2 | DisplayString (SIZE(0..32)) | read-only | current |
| swL2ACLQosFlowClassifierVlanState OBJECT-TYPE This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. attached(2) - this entry is reside in the table. detached(3) - writing this value to the object, and then the corresponding entry will be removed from the table. | 1.3.6.1.4.1.2272.1.201.1.2.16.4.1.3 | INTEGER {other(1), attached(2), detached(3)} | read-write | current |
| swL2ACLQosTemplateRuleTable OBJECT-TYPE This table specifys the template-depend rules. | 1.3.6.1.4.1.2272.1.201.1.2.16.5 | not-accessible | current | |
| swL2ACLQosTemplateRuleEntry OBJECT-TYPE A list of information specifies the template-depend rules. | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1 | not-accessible | current | |
| swL2ACLQosTemplateRuleTemplateId OBJECT-TYPE The index of template ID. | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.1 | INTEGER (0..65535) | read-only | current |
| swL2ACLQosTemplateRuleIndex OBJECT-TYPE The index of template rule. | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.2 | INTEGER (0..65535) | read-only | current |
| swL2ACLQosTemplateRuleMode OBJECT-TYPE This object indicates the rule type of the entry. | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.3 | INTEGER {other(1), security(2), qos(3), l4-switch(4)} | read-only | current |
| swL2ACLQosTemplateRuleSecuritySrcIp OBJECT-TYPE This object indicates the source IP of flow template. If the swL2ACLQosTemplateRuleMode is not security(2), then this object will be display 0.0.0.0. | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.4 | IpAddress | read-write | current |
| swL2ACLQosTemplateRuleQosFlavor OBJECT-TYPE This object indicates the rule type of the QOS mode. If the swL2ACLQosTemplateRuleMode is not qos(3), then this object must be flavor-un-used(6). | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.5 | INTEGER {flavor-8021p(1), flavor-dscp(2), flavor-ip(3), flavor-tcp(4), flavor-udp(5), flavor-un-used(6)} | read-only | current |
| swL2ACLQosTemplateRuleQosValue OBJECT-TYPE This object must match with swL2ACLQosTemplateRuleQosFlavor. If the type is flavor-8021p(1), the range of this object is 0~7. If the type is flavor-dscp(2), the range of this object is 0~63. If the type is flavor-tcp(4) or flavor-udp(5), the range of this object is 1~65535. If the swL2ACLQosTemplateRuleMode is not qos(3), then this object must be NULL. | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.6 | OCTET STRING (SIZE(0 | 1 | 2 | 4)) | read-write | current |
| swL2ACLQosTemplateRuleQosPriority OBJECT-TYPE This object indicates the priority of ingress packets in QOS mode. If the swL2ACLQosTemplateRuleMode is not qos(3), then this object must be 0. | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.7 | INTEGER (0..7) | read-write | current |
| swL2ACLQosTemplateRuleQosDscp OBJECT-TYPE This object indicates the Dscp of ingress packets in QOS mode. If the swL2ACLQosTemplateRuleMode is not qos(3), then this object must be 0. | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.8 | INTEGER (0..63) | read-write | current |
| swL2ACLQosTemplateRuleL4SwitchSessionType OBJECT-TYPE This object indicates the rule type of the TCP-Session in L4-Switch mode. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be un-used(4). | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.9 | INTEGER {tcp(1), udp(2), other(3), un-used(4)} | read-write | current |
| swL2ACLQosTemplateRuleL4SwitchSessionTCPDstIp OBJECT-TYPE This object indicates the destination ipaddress in the configured L4 TCP-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be 0.0.0.0. | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.10 | IpAddress | read-write | current |
| swL2ACLQosTemplateRuleL4SwitchSessionTCPSrcIp OBJECT-TYPE This object indicates the source ipaddress in the configured L4 TCP-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be 0.0.0.0. | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.11 | IpAddress | read-write | current |
| swL2ACLQosTemplateRuleL4SwitchSessionTCPTos OBJECT-TYPE This object indicates the type of service in the configured L4 TCP-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be zero. | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.12 | OCTET STRING (SIZE(0..1)) | read-write | current |
| swL2ACLQosTemplateRuleL4SwitchSessionTCPDstPort OBJECT-TYPE This object indicates the destination TCP port number in the configured L4 TCP-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be 0. | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.13 | INTEGER (0..65535) | read-write | current |
| swL2ACLQosTemplateRuleL4SwitchSessionTCPSrcPort OBJECT-TYPE This object indicates the source TCP port number in the configured L4 TCP-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be 0. | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.14 | INTEGER (0..65535) | read-write | current |
| swL2ACLQosTemplateRuleL4SwitchSessionTCPFlags OBJECT-TYPE This object indicates the TCP flags in the configured L4 TCP- session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be un-used(7). This object is deprecated because it just can let user to choose one of these items. | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.15 | INTEGER {fin(1), syn(2), rst(3), psh(4), ack(5), urg(6), un-used(7)} | read-write | deprecated |
| swL2ACLQosTemplateRuleL4SwitchSessionUDPDstIp OBJECT-TYPE This object indicates the destination ipaddress in the configured L4 UDP-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be 0.0.0.0. | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.16 | IpAddress | read-write | current |
| swL2ACLQosTemplateRuleL4SwitchSessionUDPSrcIp OBJECT-TYPE This object indicates the soruce ipaddress in the configured L4 UDP-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be 0.0.0.0. | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.17 | IpAddress | read-write | current |
| swL2ACLQosTemplateRuleL4SwitchSessionUDPTos OBJECT-TYPE This object indicates the type of service in the configured L4 UDP-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be zero. | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.18 | OCTET STRING (SIZE(0..1)) | read-write | current |
| swL2ACLQosTemplateRuleL4SwitchSessionUDPDstPort OBJECT-TYPE This object indicates the destination UDP port number in the configured L4 UDP-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be 0. | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.19 | INTEGER (0..65535) | read-write | current |
| swL2ACLQosTemplateRuleL4SwitchSessionUDPSrcPort OBJECT-TYPE This object indicates the source UDP port number in the configured L4 UDP-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be 0. | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.20 | INTEGER (0..65535) | read-write | current |
| swL2ACLQosTemplateRuleL4SwitchSessionOtherDstIp OBJECT-TYPE This object indicates the destination ipaddress in the configured L4 OTHER-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be 0.0.0.0. | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.21 | IpAddress | read-write | current |
| swL2ACLQosTemplateRuleL4SwitchSessionOtherSrcIp OBJECT-TYPE This object indicates the source ipaddress in the configured L4 OTHER-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be 0.0.0.0. | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.22 | IpAddress | read-write | current |
| swL2ACLQosTemplateRuleL4SwitchSessionOtherTos OBJECT-TYPE This object indicates the type of service in the configured L4 OTHER-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be zero. | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.23 | OCTET STRING (SIZE(0..1)) | read-write | current |
| swL2ACLQosTemplateRuleL4SwitchSessionOtherL4Protocol OBJECT-TYPE This object indicates the l4_protocol in the configured L4 OTHER-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be un-used(3). | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.24 | INTEGER {icmp(1), igmp(2), un-used(3)} | read-write | current |
| swL2ACLQosTemplateRuleL4SwitchSessionOtherICMPType OBJECT-TYPE This object indicates the type of ICMP message in the configured L4 OTHER-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be zero. | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.25 | OCTET STRING (SIZE(0..1)) | read-write | current |
| swL2ACLQosTemplateRuleL4SwitchSessionOtherICMPCode OBJECT-TYPE This object indicates the code of ICMP message in the configured L4 OTHER-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be zero. | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.26 | OCTET STRING (SIZE(0..1)) | read-write | current |
| swL2ACLQosTemplateRuleL4SwitchSessionOtherIGMPType OBJECT-TYPE This object indicates the IGMP type in the configured L4 OTHER-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be un-used(5). If the object be set to response-version-all(4), it means to create two entries with response-version-1(2) and response-version-2(3). | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.27 | INTEGER {query(1), response-version-1(2), response-version-2(3), response-version-all(4), un-used(5)} | read-write | current |
| swL2ACLQosTemplateRuleL4SwitchActionType OBJECT-TYPE This object indicates the action when a packet matches an entry of l4_switch mode. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be un-used(4). | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.28 | INTEGER {drop(1), forward(2), redirect(3), un-used(4)} | read-write | current |
| swL2ACLQosTemplateRuleL4SwitchActionForwardPriorityState OBJECT-TYPE This object decide to sending the packet to one of 8 hardware priority queues or not. | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.29 | INTEGER {other(1), true(2), false(3)} | read-write | current |
| swL2ACLQosTemplateRuleL4SwitchActionForwardPriority OBJECT-TYPE This object indicates the priority related to one of 8 hardware priority queues. If the swL2ACLQosTemplateRuleMode is not l4-switch(4) or the swL2ACLQosTemplateRuleL4SwitchActionForwardPriorityState is not true(2), this object must be 0. | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.30 | INTEGER (0..7) | read-write | current |
| swL2ACLQosTemplateRuleL4SwitchActionForwardDscp OBJECT-TYPE If the swL2ACLQosTemplateRuleMode is not l4-switch(4) or the swL2ACLQosTemplateRuleL4SwitchActionForwardPriorityState is not true(2),, this object must be 0. | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.31 | INTEGER (0..63) | read-write | current |
| swL2ACLQosTemplateRuleL4SwitchActionRedirectIp OBJECT-TYPE This object indicates the redirected IP address that when a packet matches an entry of l4_switch mode. If the swL2ACLQosTemplateRuleL4SwitchActionType is not redirect(3), this object must be 0.0.0.0. | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.32 | IpAddress | read-write | current |
| swL2ACLQosTemplateRuleL4SwitchActionRedirectDropUnreachable OBJECT-TYPE This object indicates the action of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. false(2) - routing unreachable packet by using L2/IPv4 router forwarding table. true(3) - dropping unreachable packet | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.33 | INTEGER {other(1), true(2), false(3)} | read-write | current |
| swL2ACLQosTemplateRuleState OBJECT-TYPE This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry is reside in the table. | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.34 | INTEGER {other(1), invalid(2), valid(3)} | read-write | current |
| swL2ACLQosTemplateRuleL4SwitchSessionTCPFlagsAll OBJECT-TYPE This object indicates the TCP flags in the configured L4 TCP- session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be zero. | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.35 | Bits {fin(0), syn(1), rst(2), psh(3), ack(4), urg(5)} | read-write | current |
| swL2ACLQosTemplateRuleSecurityDstIp OBJECT-TYPE This object indicates the destination IP of flow template. If the swL2ACLQosTemplateRuleMode is not security(2), then this object will be display 0.0.0.0. | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.36 | IpAddress | read-write | current |
| swL2ACLQosDestinationIpFilterTable OBJECT-TYPE This table defines information for the device to filter packets with specific Destination IP address. The IP address can be a unicast address or multicast address. This table has higher priority than both static FDB table and IGMP table. It means that if a IP address appears on this table also appears on the static FDB table, the device will use the information provide by this table to process the packet. | 1.3.6.1.4.1.2272.1.201.1.2.16.6 | not-accessible | current | |
| swL2ACLQosDestinationIpFilterEntry OBJECT-TYPE A list of information about a specific unicast/multicast IP address for which the switch has filtering information. | 1.3.6.1.4.1.2272.1.201.1.2.16.6.1 | not-accessible | current | |
| swL2ACLQosDestinationIpFilterIndex OBJECT-TYPE The index of this rule. | 1.3.6.1.4.1.2272.1.201.1.2.16.6.1.1 | INTEGER (0..65535) | read-only | obsolete |
| swL2ACLQosDestinationIpFilterIpAddr OBJECT-TYPE This object indicates a unicast IP address for which the switch has filtering information. | 1.3.6.1.4.1.2272.1.201.1.2.16.6.1.2 | IpAddress | read-only | current |
| swL2ACLQosDestinationIpFilterState OBJECT-TYPE This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry is reside in the table. | 1.3.6.1.4.1.2272.1.201.1.2.16.6.1.3 | INTEGER {other(1), invalid(2), valid(3)} | read-write | current |
| swL2ACLQosFDBFilterTable OBJECT-TYPE This table defines information for the device to filter packets with specific MAC address (either as the DA and/or as the SA). The MAC address can be a unicast address or a multicast address. This table has higher priority than both static FDB table and IGMP table. It means that if a MAC address appears on this table also appears on the static FDB table, the device will use the information provide by this table to process the packet. | 1.3.6.1.4.1.2272.1.201.1.2.16.7 | not-accessible | current | |
| swL2ACLQosFDBFilterEntry OBJECT-TYPE A list of information about a specific unicast/multicast MAC address for which the switch has filtering information. | 1.3.6.1.4.1.2272.1.201.1.2.16.7.1 | not-accessible | current | |
| swL2ACLQosFDBFilterIndex OBJECT-TYPE The index of this rule. | 1.3.6.1.4.1.2272.1.201.1.2.16.7.1.1 | INTEGER (0..65535) | read-only | obsolete |
| swL2ACLQosFDBFilterVlanName OBJECT-TYPE The existence of VALN name. | 1.3.6.1.4.1.2272.1.201.1.2.16.7.1.2 | DisplayString (SIZE(0..32)) | read-only | current |
| swL2ACLQosFDBFilterMacAddress OBJECT-TYPE This object will filter on destination MAC address operates on bridged packets, but not on routed packets. And It will filter on source MAC operates on all packets. | 1.3.6.1.4.1.2272.1.201.1.2.16.7.1.3 | MacAddress | read-only | current |
| swL2ACLQosFDBFilterState OBJECT-TYPE This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry is reside in the table. | 1.3.6.1.4.1.2272.1.201.1.2.16.7.1.4 | INTEGER {other(1), invalid(2), valid(3)} | read-write | current |
| swL2ACLQosIpFragmentFilterDropPkts OBJECT-TYPE This object decide to drop fragmented IP packets or not. | 1.3.6.1.4.1.2272.1.201.1.2.16.8 | INTEGER {other(1), disabled(2), enabled(3)} | read-write | current |
| swL2ACLQosSchedulingTable OBJECT-TYPE The switch contains 4 hardware priority queues. Incoming packets must be mapped to one of these four queues. Each hardware queue will transmit all of the packets in its buffer before allowing the next lower priority queue to transmit its packets. When the lowest hardware priority queue has finished transmitting all of its packets, the highest hardware priority queue can again transmit any packets it may have received. | 1.3.6.1.4.1.2272.1.201.1.2.16.9 | not-accessible | current | |
| swL2ACLQosSchedulingEntry OBJECT-TYPE A list of information specifies the Qos output scheduling Table. | 1.3.6.1.4.1.2272.1.201.1.2.16.9.1 | not-accessible | current | |
| swL2ACLQosSchedulingPortIndex OBJECT-TYPE The index of logical port. | 1.3.6.1.4.1.2272.1.201.1.2.16.9.1.1 | INTEGER (0..65535) | read-only | current |
| swL2ACLQosSchedulingClassId OBJECT-TYPE This specifies which of the four hardware priority queues. The four hardware priority queues are identified by number, from 0 to 3, with the 0 queue being the lowest priority. | 1.3.6.1.4.1.2272.1.201.1.2.16.9.1.2 | INTEGER (0..3) | read-only | current |
| swL2ACLQosSchedulingWRRValue OBJECT-TYPE Specifies the weighted round robin (WRR) the above specified hardware priority queue will be allowed to transmit before allowing the next lowest priority queue to transmit its packets. | 1.3.6.1.4.1.2272.1.201.1.2.16.9.1.3 | INTEGER (0..255) | read-write | current |
| swL2ACLQosMacPriorityTable OBJECT-TYPE This table indicates the destination mac priority in flow classifier. | 1.3.6.1.4.1.2272.1.201.1.2.16.10 | not-accessible | current | |
| swL2ACLQosMacPriorityEntry OBJECT-TYPE A list of information specifies the destination mac priority in flow classifier. | 1.3.6.1.4.1.2272.1.201.1.2.16.10.1 | not-accessible | current | |
| swL2ACLQosMacPriorityIndex OBJECT-TYPE The index of this rule. | 1.3.6.1.4.1.2272.1.201.1.2.16.10.1.1 | INTEGER (0..65535) | read-only | obsolete |
| swL2ACLQosMacPriorityVlanName OBJECT-TYPE The existence VLAN name. | 1.3.6.1.4.1.2272.1.201.1.2.16.10.1.2 | DisplayString (SIZE(0..32)) | read-only | current |
| swL2ACLQosMacPriorityDstMacAddress OBJECT-TYPE This object will filter on destination MAC address operates on bridged packets, but not on routed packets. And It will filter on source MAC operates on all packets. | 1.3.6.1.4.1.2272.1.201.1.2.16.10.1.3 | MacAddress | read-only | current |
| swL2ACLQosMacPriorityPriorityValue OBJECT-TYPE This object indicates the priority related to one of 8 hardware priority queues. | 1.3.6.1.4.1.2272.1.201.1.2.16.10.1.4 | INTEGER (0..7) | read-write | current |
| swL2ACLQosMacPriorityState OBJECT-TYPE This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry is reside in the table. | 1.3.6.1.4.1.2272.1.201.1.2.16.10.1.5 | INTEGER {other(1), invalid(2), valid(3)} | read-write | current |
| swL2MgmtPortMgmt OBJECT-IDENTITY | 1.3.6.1.4.1.2272.1.201.1.2.17 | |||
| swL2MgmtPortCurrentLinkStatus OBJECT-TYPE This object indicates the current management port link status. | 1.3.6.1.4.1.2272.1.201.1.2.17.1 | INTEGER {other(1), link-pass(2), link-fail(3)} | read-only | current |
| swL2MgmtPortCurrentNwayStatus OBJECT-TYPE This object indicates the current management port speed and duplex mode. | 1.3.6.1.4.1.2272.1.201.1.2.17.2 | INTEGER {other(1), half-10Mbps(2), full-10Mbps(3), half-100Mbps(4), full-100Mbps(5)} | read-only | current |
| swL2MgmtPortAdminState OBJECT-TYPE This object decide the management port enabled or disabled. | 1.3.6.1.4.1.2272.1.201.1.2.17.3 | INTEGER {other(1), disabled(2), enabled(3)} | read-write | current |
| swL2MgmtPortNwayState OBJECT-TYPE Chose the management port speed, duplex mode, and N-Way function mode. | 1.3.6.1.4.1.2272.1.201.1.2.17.4 | INTEGER {other(1), nway-enabled(2), nway-disabled-10Mbps-Half(3), nway-disabled-10Mbps-Full(4), nway-disabled-100Mbps-Half(5), nway-disabled-100Mbps-Full(6)} | read-write | current |
| swL2MgmtPortFlowCtrlState OBJECT-TYPE The flow control mechanism is different between full duplex mode and half duplex mode. For half duplex mode, the jamming signal is asserted. For full duplex mode, IEEE 802.3x flow control function sends PAUSE frames and receives PAUSE frames. | 1.3.6.1.4.1.2272.1.201.1.2.17.5 | INTEGER {other(1), disabled(2), enabled(3)} | read-write | current |
| swL2MgmtPortLinkUpDownTrapEnable OBJECT-TYPE Indicates whether linkUp/linkDown traps should be generated for the management port. By default, this object should have the value enabled(3). | 1.3.6.1.4.1.2272.1.201.1.2.17.6 | INTEGER {other(1), disabled(2), enabled(3)} | read-write | current |
Notifications
| Name | OID | Status |
|---|---|---|
| managementPortLinkUp NOTIFICATION-TYPE The trap is sent whenever the management port is link up. | 1.3.6.1.4.1.2272.1.201.1.2.0.1 | |
| managementPortLinkDown NOTIFICATION-TYPE The trap is sent whenever the management port is link down. | 1.3.6.1.4.1.2272.1.201.1.2.0.2 |