SWITCH

TEXTUAL-CONVENTION

arp's type, request or response.

TEXTUAL-CONVENTION

The Bridge-Identifier, as used in the Spanning Tree Protocol, to uniquely identify a bridge.Its first two octets (in network byte order) contain a priority value, and its last 6 octets contain the MAC address used to refer to a bridge in a unique fashion (typically, the numerically smallest MAC address of all ports on the bridge).

TEXTUAL-CONVENTION

The status of the specified operation can be one of the following. opInProgress : the operation is in process. opSuccess : the operation has been completed successfully. opInvalid : the command is invalid or command-protocol-device combination is unsupported by the system. opInvalidProtocol :invalid protocol is specified opInvalidSourceName :invalid source file name is specified. opInvalidDestName :invalid target name is specified. opInvalidServerAddress :invalid server address is specified opDeviceBusy :the device is in use and locked by another process opDeviceOpenError :invalid device name is specified. opDeviceError : device read, write or erase error opDeviceNotProgrammable :device isread-only but a write or erase operation was specified opDeviceFull : device is filled to capacity opFileOpenError :invalid file name; file not found in partition opFileTransferError :file transfer was unsuccessful opFileChecksumError :file checksum in Cf is invalid opNoMemory :system is running in low on memory opUnknownFailure :failure which is unknown opDeleteFileOpenError :file is in used by another process opDeleteInvalidDevice :invalid device name is specified opDeleteInvalidFunction :deleted operation is unsupported by the device opDeleteOperationError :operation is in a low error opDeleteInvalidFileName :invalid file name is specified pDeleteDeviceBusy :the device is in use and locked by another process opDeleteParaError :the parameters are invalid opDeleteInvalidPath :the file path is invalid.

TEXTUAL-CONVENTION

Color of the flow.

TEXTUAL-CONVENTION

cleared: Reset the value of the rule's counter. nouse: 'nouse' will be returned when getting.

TEXTUAL-CONVENTION

The value of DSCP. <0-64> Value of DSCP af11 Specify Assured Forwarding 11 service(10) af12 Specify Assured Forwarding 12 service(12) af13 Specify Assured Forwarding 13 service(14) af21 Specify Assured Forwarding 21 service(18) af22 Specify Assured Forwarding 22 service(20) af23 Specify Assured Forwarding 23 service(22) af31 Specify Assured Forwarding 31 service(26) af32 Specify Assured Forwarding 32 service(28) af33 Specify Assured Forwarding 33 service(30) af41 Specify Assured Forwarding 41 service(34) af42 Specify Assured Forwarding 42 service(36) af43 Specify Assured Forwarding 43 service(38) be Specify Best Effort service(0) cs1 Specify Class Selector 1 service(8) cs2 Specify Class Selector 2 service(16) cs3 Specify Class Selector 3 service(24) cs4 Specify Class Selector 4 service(32) cs5 Specify Class Selector 5 service(40) cs6 Specify Class Selector 6 service(48) cs7 Specify Class Selector 7 service(56) ef Specify Expedited Forwarding service(46) nouse Do not use this filter(64)

TEXTUAL-CONVENTION

The direction of policy on at interface.

TEXTUAL-CONVENTION

The direction of policy on at interface.

TEXTUAL-CONVENTION

A simpleStatus value for the object.

TEXTUAL-CONVENTION

Represents a possible error condition.

TEXTUAL-CONVENTION

Specify loghost facility which generates messages.

TEXTUAL-CONVENTION

The status of the specified operation can be one of the following. opInProgress : the operation is in process. opSuccess : the operation has been completed successfully. opInvalid : the command is invalid or command-protocol-device combination is unsupported by the system. opInvalidProtocol :invalid protocol is specified opInvalidSourceName :invalid source file name is specified. opInvalidDestName :invalid target name is specified. opInvalidServerAddress :invalid server address is specified opDeviceBusy :the device is in use and locked by another process opDeviceOpenError :invalid device name is specified. opDeviceError : device read, write or erase error opDeviceNotProgrammable :device isread-only but a write or erase operation was specified. opDeviceFull : device is filled to capacity opFileOpenError :invalid file name; file not found in partition opFileTransferError :file transfer was unsuccessful opFileChecksumError :file checksum in Flash is invalid opNoMemory :system is running in low on memory opUnknownFailure :failure which is unknown opDeleteFileOpenError :file is in used by another process opDeleteInvalidDevice :invalid device name is specified opDeleteInvalidFunction :deleted operation is unsupported by the device. opDeleteOperationError :operation is in a low error opDeleteInvalidFileName :invalid file name is specified pDeleteDeviceBusy :the device is in use and locked by another process. opDeleteParaError :the parameters are invalid opDeleteInvalidPath :the file path is invalid.

TEXTUAL-CONVENTION

Specify the type to reactive.

TEXTUAL-CONVENTION

Queue Id

TEXTUAL-CONVENTION

p source guard's binding type, ip, ip-mac, ip-vlan, ip-mac-vlan.

TEXTUAL-CONVENTION

Specify severity level of message.

TEXTUAL-CONVENTION

Specify severity level of message.

TEXTUAL-CONVENTION

Specify severity level of message.

TEXTUAL-CONVENTION

The operation type of TCP and UDP. lt : Less than given port number. eq : Equal to given port number. gt : Greater than given port number. -- neq : Not equal to given port number. range : Between two port numbers.

TEXTUAL-CONVENTION

The value of IP-packet's precedence. <0-7> Value of precedence routine Specify routine precedence(0) priority Specify priority precedence(1) immediate Specify immediate precedence(2) flash Specify flash precedence(3) flash-override Specify flash-override precedence(4) critical Specify critical precedence(5) internet Specify internetwork control precedence(6) network Specify network control precedence(7)

TEXTUAL-CONVENTION

prefix list value: 1.

TEXTUAL-CONVENTION

prefix list type, permit or deny.

TEXTUAL-CONVENTION

Type of map.

TEXTUAL-CONVENTION

cleared: Reset the value of the rule's counter. nouse: 'nouse' will be returned when getting.

TEXTUAL-CONVENTION

The value of rule's action. permit: The packet matching the rule will be permitted to forward. deny: The packet matching the rule will be denied.

TEXTUAL-CONVENTION

Specify the place to boot to.

TEXTUAL-CONVENTION

Specify operation types on time stamp of message. none: no time stamp information in message. date: the time stamp type of message is date. boot: the time stamp type of message is the time from uptime of system. dateWithoutYear: the time stamp type of message is date without year information.

TEXTUAL-CONVENTION

A value used to index vlan class enable based.

TEXTUAL-CONVENTION

A value used to index vlan class group tables: values of 0 to 31 are permitted.

TEXTUAL-CONVENTION

This data type is used to model IPv6 addresses. This is a binary string of 16 octets in network byte-order.

TEXTUAL-CONVENTION

A value used to index vlan class Protocols.

TEXTUAL-CONVENTION

A value used to index vlan class rule tables: values of 0 to 4095 are permitted.

TEXTUAL-CONVENTION

A value used to index per-VLAN tables: values of 0 and 4095 are not permitted.If the value is between 1 and 4094 inclusive, it represents an IEEE 802.1Q VLAN-ID with global scope within a given bridged domain (see VlanId textual convention).If the value is greater than 4095, then it represents a VLAN with scope local to the particular agent, i.e., one without a global VLAN-ID assigned to it.Such VLANs are outside the scope of IEEE 802.1Q, but it is convenient to be able to manage them in the same way using this MIB.

TEXTUAL-CONVENTION

Each octet within this value specifies a set of eight VLANs.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

Bogus Index. This should always return the integer 0.

OBJECT-TYPE

The total amount of real/physical memory installed on this host.

OBJECT-TYPE

The total amount of memory free or available for use on this host.This value typically covers both real memory and swap space or virtual memory.

OBJECT-TYPE

The total amount of memory used on this host. This value typically covers both real memory and swap space or virtual memory.

OBJECT-IDENTITY

OBJECT-TYPE

Bogus Index.This should always return the integer 1.

OBJECT-TYPE

The percentage of processor time spent idle, calculated over the last minute.

OBJECT-TYPE

The system precess table.

OBJECT-TYPE

An entity process entry. Each entry consists of information of an process. The sysProcessIndex exclusively defines an process id.

OBJECT-TYPE

The pid of process.

OBJECT-TYPE

The name of the process.

OBJECT-IDENTITY

OBJECT-TYPE

This should always write running-config to startup-config.And the valid set value is 1. When get the configSave value, 1 means success, 0 means failure.

OBJECT-TYPE

This should allow to reboot the switch.The valid input value is 1 and 2. Value 1 means the switch will reboot without savingcurrent configuration. Value 2 means the switch will savecurrent configuration before reboot the switch.

OBJECT-TYPE

Specify auto reboot parameters at the special time. 0 is mean clear.

OBJECT-TYPE

Specify auto reboot parameters reboot after delay some time. The value is [1, 720] minutes. 0 is mean clear.

OBJECT-TYPE

Description the current version

OBJECT-TYPE

Telnet service.1:enable 2:disable.

OBJECT-TYPE

This node only for login fail for three time.

OBJECT-TYPE

Save the last command line and time.

OBJECT-TYPE

Show the current running image.

OBJECT-TYPE

Show system startup time.

OBJECT-TYPE

The system image management table.

OBJECT-TYPE

An entity image entry.Each entry consists of information of an entity image. The sysImageIndex exclusively defines an image file.

OBJECT-TYPE

The index of image.

OBJECT-TYPE

The file name of the image.

OBJECT-TYPE

The create time of the image.

OBJECT-TYPE

The version of the image.

OBJECT-TYPE

The size of the image.

OBJECT-TYPE

The dir of the image.

OBJECT-TYPE

This image is the boot image (1),and is not the boot image (2). Only support enable(1).

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

This table gives the properties of all the flashes on the system.

OBJECT-TYPE

The entry of flashTable.

OBJECT-TYPE

The index of flashTable.It has a minimum value of 1, and maximum value of the same as the value of flhSupportNum.

OBJECT-TYPE

Specifies the total size of the flash device indexed by flhIndex. The value should be zero if the flash is removed for a removable device.

OBJECT-TYPE

Specifies the free size of the flash device.

OBJECT-TYPE

The flash name within the system.

OBJECT-TYPE

DESCRIPTION of the purpose of the flash in the system.

OBJECT-IDENTITY

OBJECT-TYPE

Table of file information.

OBJECT-TYPE

An entry representing a file.Indexed using flash number, partition number, and file number.

OBJECT-TYPE

Index of the table, whose range is from 1 to 2147483647.

OBJECT-TYPE

A valid file name supported by the file system.

OBJECT-TYPE

The file size in bytes excluding the file header of file system. The value should be greater than zero.

OBJECT-TYPE

The time when this file is modified last time.

OBJECT-IDENTITY

OBJECT-TYPE

Table used to operate flash.

OBJECT-TYPE

Note an operation can not be stopped until it is finished. If notification is configured, NMS will receive a notification at the end of the operation. Entries in the table will be removed automatically in 5 minutes. It can also be deleted by NMS directly.

OBJECT-TYPE

Specifies the index of an entry.It is a random value when creating an entry.

OBJECT-TYPE

Specifies the operation to be executed. flash2Flash(1) Copy a file from flash to flash. net2Flash(2) Copy a file from net to flash; flash2Net(3) Copy a file from flash to net. delete(4) Delete a file from flash, the file name is specified by flhOperSourceFile; rename(5) Change a file's name.

OBJECT-TYPE

Specifies the protocol used to transfer file. The default protocol is ftp. Both member switch and commander switch can use them if they support HGMP v2. 1 FTP 2 TFTP

OBJECT-TYPE

The address of remote host acting as server for operation. The default value is 0.0.0.0.

OBJECT-TYPE

When using ftp to transfer files, the user name must be specified through this node.

OBJECT-TYPE

Remote user password for copying via ftp protocol.Optionally, This object may be ignored for protocols other than ftp.

OBJECT-TYPE

Specifies the source file name to be transferred. It may be located on flash or remote server. It may include the file path if it is applicable. It must be specified.

OBJECT-TYPE

Specifies the destination file name. It may be located on flash or remote server. It may include the file path if it is applicable. If it is not specified, the destination file name is the same as source file name for application.

OBJECT-TYPE

The status of the specified operation can be one of the following. opInProgress(1) : the operation is in process. opSuccess(2) : the operation has been completed successfully. opInvalid(3) : the command is invalid or command-protocol-device combination is unsupported by the system. opInvalidProtocol(4) :invalid protocol is specified opInvalidSourceName(5) :invalid source file name is specified. opInvalidDestName(6) :invalid target name is specified. opInvalidServerAddress(7) :invalid server address is specified opDeviceBusy(8) :the device is in use and locked by another process opDeviceOpenError(9) :invalid device name is specified. opDeviceError(10) : device read, write or erase error opDeviceNotProgrammable(11) :device isread-only but a write or erase operation was specified. opDeviceFull(12) : device is filled to capacity opFileOpenError(13) :invalid file name; file not found in partition opFileTransferError(14) :file transfer was unsuccessful opFileChecksumError(15) :file checksum in Flash is invalid opNoMemory(16) :system is running in low on memory opUnknownFailure(19) :failure which is unknown opDeleteFileOpenError(20) :file is in used by another process opDeleteInvalidDevice(21) :invalid device name is specified opDeleteInvalidFunction(22) :deleted operation is unsupported by the device. opDeleteOperationError(23) :operation is in a low error opDeleteInvalidFileName(24) :invalid file name is specified pDeleteDeviceBusy(25) :the device is in use and locked by another process. opDeleteParaError(26) :the parameters are invalid opDeleteInvalidPath(27) :the file path is invalid.

OBJECT-TYPE

If use management interface running SNMP or not, true(1):enable.false(2):disable

OBJECT-TYPE

The status of this conceptual row.Now only realize CreateAndGo and Destroy and Active. 1 means Active 4 means CreateAndGo 6 means Destroy

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

This table gives the properties of all the cfes on the system.

OBJECT-TYPE

The entry of cfTable.

OBJECT-TYPE

The index of cfTable.It has a minimum value of 1, and maximum value of the same as the value of cfSupportNum.

OBJECT-TYPE

Specifies the total size of the cf device indexed by cfIndex.The value should be zero if the cf is removed for a removable device.

OBJECT-TYPE

Specifies the free size of the cf device.

OBJECT-TYPE

The cf name within the system.

OBJECT-TYPE

Description of the purpose of the cf in the system.

OBJECT-IDENTITY

OBJECT-TYPE

Table of file information.

OBJECT-TYPE

An entry representing a file. Indexed using cf number, partition number, and file number.

OBJECT-TYPE

Index of the table, whose range is from 1 to 2147483647

OBJECT-TYPE

A valid file name supported by the file system.

OBJECT-TYPE

The file size in bytes excluding the file header of file system. The value should be greater than zero.

OBJECT-TYPE

The time when this file is modified last time.

OBJECT-IDENTITY

OBJECT-TYPE

Table used to operate cf.

OBJECT-TYPE

Note an operation can not be stopped until it is finished. If notification is configured, NMS will receive a notification at the end of the operation. Entries in the table will be removed automatically in 5 minutes. It can also be deleted by NMS directly.

OBJECT-TYPE

Specifies the index of an entry. It is a random value when creating an entry.

OBJECT-TYPE

Specifies the operation to be executed. net2CfWithErase Copy a file to cf; erase cf beforehand. net2CfWithoutErase Copy a file to cf; do not erase cf beforehand. cf2Net Copy a file from cf. delete Delete a file from cf, the file name is specified by cfOperSourceFile; rename Change a file's name.

OBJECT-TYPE

Specifies the protocol used to transfer file.The default protocol is ftp. when 'clusterftp' or 'clustertftp' is selected, the cfOperServerAddress needn't be set the server address can be acquired automatically, the value of cfOperServerAddress is uncertain during operation.Both member switch and commander switch can use them if they support HGMP v2.

OBJECT-TYPE

The address of remote host acting as server for operation. The default value is 255.255.255.255.

OBJECT-TYPE

When using ftp to transfer files, the user name must be specified through this node.

OBJECT-TYPE

Remote user password for copying via ftp protocol.Optionally. This object may be ignored for protocols other than ftp.

OBJECT-TYPE

Specifies the source file name to be transferred. It may be located on cf or remote server. It may include the file path if it is applicable. It must be specified.

OBJECT-TYPE

Specifies the destination file name. It may be located on cf or remote server. It may include the file path if it is applicable. If it is not specified, the destination file name is the same as source file name for application.

OBJECT-TYPE

The status of operation.

OBJECT-TYPE

If use management interface running SNMP or not.

OBJECT-TYPE

The status of this conceptual row.Now only realize CreateAndGo and Destroy and Active. 1 means Active 4 means CreateAndGo 6 means Destroy

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

current time. format HH:MM:SS.

OBJECT-TYPE

Month of the year. range is [1, 12].

OBJECT-TYPE

Day of the month. range is [1, 31].

OBJECT-TYPE

Year of the date. range is [2000, 2037].

OBJECT-TYPE

The table of SummerTime.

OBJECT-TYPE

The entry of timezone.

OBJECT-TYPE

Zone name, must be less than 32 characters. only include [a-zA-Z_]. The begin and end character must be alphabet. Its length range is [3, 32)

OBJECT-TYPE

Positive/Negative time zone offset from UTC. 0 means Negative 1 means Positive

OBJECT-TYPE

Hours offset from UTC, must be range 0~23.

OBJECT-TYPE

Minutes offset from UTC, must be range 0~59.

OBJECT-TYPE

Seconds offset from UTC, must be range 0~59.

OBJECT-TYPE

The status of this conceptual row.Now only realize CreateAndGo and Destroy and Active. 1 means Active 4 means CreateAndGo 6 means Destroy

OBJECT-TYPE

The table of SummerTime.

OBJECT-TYPE

The entry of SummerTime.

OBJECT-TYPE

Zone name, must be less than 32 characters. only include [a-zA-Z_]. The begin and end character must be alphabet. Its length range is [1, 32)

OBJECT-TYPE

Start month of the year. range is [1,12]

OBJECT-TYPE

Day in month to start. range is [1, 31].

OBJECT-TYPE

Time to start. format HH:MM:SS

OBJECT-TYPE

Month to end. range is [1, 12].

OBJECT-TYPE

Day in month to end. range is [1, 31].

OBJECT-TYPE

Time to end. format HH:MM:SS

OBJECT-TYPE

Summer time offset, unit is minute. range is [1, 1440].

OBJECT-TYPE

The status of this conceptual row.Now only realize CreateAndGo and Destroy and Active. 1 means Active 4 means CreateAndGo 6 means Destroy

OBJECT-TYPE

The table of SummerTime.

OBJECT-TYPE

The entry of SummerTime.

OBJECT-TYPE

Zone name, must be less than 32 characters. only include [a-zA-Z_]. The begin and end character must be alphabet. Its length range is [1, 32)

OBJECT-TYPE

Start month of the year. range is [1, 12].

OBJECT-TYPE

Start day of month. range is [1, 31].

OBJECT-TYPE

Start year of summer-time. range is [2000, 2037].

OBJECT-TYPE

Start time. format HH:MM:SS.

OBJECT-TYPE

End month of year. range is [1, 12].

OBJECT-TYPE

End day of month. range is [1, 31].

OBJECT-TYPE

End year of summer time. range is [2000, 2037].

OBJECT-TYPE

End time. format HH:MM:SS.

OBJECT-TYPE

Summer time offset, unit is minute. range is [1, 1440].

OBJECT-TYPE

The status of this conceptual row.Now only realize CreateAndGo and Destroy and Active. 1 means Active 4 means CreateAndGo 6 means Destroy

OBJECT-IDENTITY

OBJECT-TYPE

CPU usage within five seconds.

OBJECT-TYPE

CPU usage within one minute.

OBJECT-TYPE

CPU usage within five minutes.

OBJECT-IDENTITY

OBJECT-TYPE

The log timestamp type. 0 RBSD(RFC3164 or bsd). 1 RISO(RFC3339 or iso). 2 RFULL(date). 3 NONE.

OBJECT-TYPE

The state of log operate true(1):enable.false(2):disable.

OBJECT-IDENTITY

OBJECT-TYPE

The maximum number of messages that can be storedin logbuffer.MaxSize range 10~1000.

OBJECT-TYPE

The operations staff can selectively filter the messages with priority which consists of severity that generates the message and severity of the message.Range 0~7.

OBJECT-TYPE

The number of log messages stored in logbuffer.

OBJECT-TYPE

The number of log messages dropped in logbuffer.

OBJECT-IDENTITY

OBJECT-TYPE

The state of log merge true(1):enable.false(2):disable.

OBJECT-TYPE

The operations staff can selectively filter the messages with priority which consists of severity that generates the message and severity of the message.Range 0~7.

OBJECT-IDENTITY

OBJECT-TYPE

The state of syslogtrap: true(1): enable.false(2): disable.

OBJECT-TYPE

The operations staff can selectively filter the messages with priority which consists of facility that generates the message and severity of the message.Value range 0~11 or 16~23.

OBJECT-TYPE

The operations staff can selectively filter the messages with priority which consists of severity that generates the message and severity of the message.Value range 0~7.default 4

OBJECT-TYPE

The table of loghost.

OBJECT-TYPE

The loghost entry of syslog.

OBJECT-TYPE

The ip address of loghost.

OBJECT-TYPE

The mgmt if of loghost. 1 noUse. 2 useMgmtIf.

OBJECT-TYPE

The status of this conceptual row.Now only realize CreateAndGo and Destroy and Active. 1 means Active 4 means CreateAndGo 6 means Destroy

OBJECT-IDENTITY

OBJECT-TYPE

The state of syslog trap. true(1):enable.false(2):disable.

OBJECT-TYPE

The operations staff can selectively filter the messages with priority which consists of severity that generates the message and severity of the message. 0 high. 1 middle. 2 lower. 3 minor.

OBJECT-IDENTITY

OBJECT-TYPE

The state of log merge true(1):enable.false(2):disable.

OBJECT-TYPE

The logging merge fifo-size, specify the logging merge buffer.

OBJECT-TYPE

The logging merge timeout value, specify the logging merge interval.default 10.

OBJECT-TYPE

Specify sync parameter. true(1): sync the syslog and return value is always 0.

OBJECT-TYPE

Clear logging buffer. true(1): clear the logging buffer and return value is always 0.

OBJECT-IDENTITY

OBJECT-TYPE

A list of mirror session source port entries.

OBJECT-TYPE

A list of parameters that describe a source port to be added to a mirror session.

OBJECT-TYPE

An index that uniquely identifies an entry in the mirror session table.

OBJECT-TYPE

IfIndex of mirror group source port. including ethernet port and agg port

OBJECT-TYPE

Mirror direction of source port.if the direction first configured as rx, then configure tx, then the direction will be both.

OBJECT-TYPE

The status of this conceptual row.Now only realize CreateAndGo and Destroy and Active. 1 means Active 4 means CreateAndGo 6 means Destroy

OBJECT-TYPE

A list of mirror session source vlan entries.

OBJECT-TYPE

A list of parameters that describe a source vlan to be added to a mirror session.

OBJECT-TYPE

An index that uniquely identifies an entry in the mirror session table.

OBJECT-TYPE

IfIndex of mirror group source vlan.

OBJECT-TYPE

Mirror direction of source vlan.if the direction first configured as rx, then configure tx, then the direction will be both.

OBJECT-TYPE

The status of this conceptual row.Now only realize CreateAndGo and Destroy and Active. 1 means Active 4 means CreateAndGo 6 means Destroy

OBJECT-TYPE

A list of mirror group dest port entries.

OBJECT-TYPE

A list of parameters that describe a dest port to be added to a mirror group.

OBJECT-TYPE

An index that uniquely identifies an entry in the mirror session table.

OBJECT-TYPE

IfIndex of mirror group dest port. only ethernet port.

OBJECT-TYPE

session type.

OBJECT-TYPE

IfIndex of mirror group dest vlan.

OBJECT-TYPE

The status of this conceptual row.Now only realize CreateAndGo and Destroy and Active. 1 means Active 4 means CreateAndGo 6 means Destroy

OBJECT-TYPE

A list of mirror group entries.

OBJECT-TYPE

A list of parameters that describe a mirror group.

OBJECT-TYPE

An index that uniquely identifies an entry in the mirror session table.

OBJECT-TYPE

The type of a mirror session. 1 Local. 2 remote.

OBJECT-TYPE

The status of a mirror session.A mirror session will be active only when it has destination port. 1 Active. 2 Inactive.

OBJECT-TYPE

The status of this conceptual row.Now only realize Destroy and Active.

OBJECT-TYPE

A list of mirror session escape mac entries.

OBJECT-TYPE

A list of parameters that describe a escape mac to be added to a mirror session.

OBJECT-TYPE

The index of a escape mac.Range 1~2.

OBJECT-TYPE

Specify certain mac address as special and not mirror.

OBJECT-TYPE

Mac mask of mirror Specify certain mac address.

OBJECT-TYPE

The status of this conceptual row.Now only realize CreateAndGo(4) and Destroy(6) and Active(1). 1 means Active 4 means CreateAndGo 6 means Destroy

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

This table defines the securityStatus of each secure port. Each port can have a number of authorised MAC addresses, and these are stored in the portSecurityStaticAddressTable and portSecurityDynamicAddressTable.

OBJECT-TYPE

There is a Rowin this table for each secure port and It is indexed using the object ifIndex in RFC1213-MIB.

OBJECT-TYPE

This attribute controls the system wide operation of mac-authentication. The system-wide mac-authentication options become non-operational when this attribute is set to disabled.

OBJECT-TYPE

This attribute determines what action to be taken when a security violation is detected protect(0): discard packet silently restrict(1): discard packet and print log shutdown(2): discard packet, log and set the interface error-disabled.

OBJECT-TYPE

This indicates the maximum value that mac addresses can be learned. Those objects are bound by the relationship: staticNumberOfConfiguredMacAddresses <= totalNumberOfMacAddresses <= portSecurityMaximumMacAddresses.

OBJECT-TYPE

This indicates thecurrent number of Mac Addresses.

OBJECT-TYPE

This table stores the static MAC addresses assigned to each port.

OBJECT-TYPE

This table stores the static MAC addresses assigned to each port.

OBJECT-TYPE

The port index which port security is configured. This is the first index into the portSecurityStaticAddressTable.

OBJECT-TYPE

The Vlan ID associate with the port and the MAC address. This is the second index into the portSecurityStaticAddressTable.

OBJECT-TYPE

The MAC address of a station assigned to this port. The index format of mac address '01:02:0a:0b:ff:ff' should be '1.2.10.11.255.255' This is the third index into the portSecurityStaticAddressTable.

OBJECT-TYPE

The status of this conceptual row.Now only realize CreateAndGo and Destroy and Active. 1 means Active 4 means CreateAndGo 6 means Destroy

OBJECT-TYPE

This table stores the dynamic MAC addresses which are learned each port.

OBJECT-TYPE

This table stores the dynamic MAC addresses which are learned each port.

OBJECT-TYPE

The Vlan ID associate with the port and the MAC address. This is the third index into the portSecurityDynamicAddressTable.

OBJECT-TYPE

The MAC address of a station assigned to this port.This is the second index into the portSecurityDynamicAddressTable.

OBJECT-TYPE

The port name which port security is configured.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

This table stores the port name and storm control unicast mode,level and pps.

OBJECT-TYPE

This table stores the port name and storm control unicast mode and level.

OBJECT-TYPE

The name of interface which is configuredstorm control.

OBJECT-TYPE

This indicates which unicast mode is configured whenstorm control is used. 1 PacketPerSecond. 2 Level.

OBJECT-TYPE

When unicast mode is configured Level,this indicates the percentage of bandwith. The valid range is (0.00-100.00).

OBJECT-TYPE

When unicast mode is configured PacketPerSecond, this indicates the number of packet per second.

OBJECT-TYPE

The status of this conceptual row.Now only realize CreateAndGo and Destroy and Active. 1 means Active 4 means CreateAndGo 6 means Destroy

OBJECT-TYPE

This table stores the port name and storm control broadcast mode,level and pps.

OBJECT-TYPE

This table stores the port name andstorm control broadcast mode and level.

OBJECT-TYPE

The name of interface which is configuredstorm control.

OBJECT-TYPE

This indicates which broadcast mode is configured whenstorm control is used. 1 PacketPerSecond. 2 Level.

OBJECT-TYPE

When broadcast mode is configured Level,this indicates the percentage of bandwith. The valid range is (0.00-100.00).

OBJECT-TYPE

When broadcast mode is configured PacketPerSecond, this indicates the number of packet per second.

OBJECT-TYPE

The status of this conceptual row.Now only realize CreateAndGo and Destroy and Active. 1 means Active 4 means CreateAndGo 6 means Destroy

OBJECT-TYPE

This table stores the port name andstorm control multicast mode and level.

OBJECT-TYPE

This table stores the port name andstorm control multicast,level and pps.

OBJECT-TYPE

The name of interface which is configuredstorm control.

OBJECT-TYPE

This indicates which multicast mode is configured whenstorm control is used. 1 PacketPerSecond. 2 Level.

OBJECT-TYPE

When multicast mode is configured Level,this indicates the percentage of bandwith. The valid range is (0.00-100.00).

OBJECT-TYPE

When multicast mode is configured PacketPerSecond, this indicates the number of packet per second.

OBJECT-TYPE

The status of this conceptual row.Now only realize CreateAndGo and Destroy and Active. 1 means Active 4 means CreateAndGo 6 means Destroy

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

This is an eight-bit integer indicating the stratum level of the local clock, with values defined as follows: 0, unspecified 1, primary reference (e.g.,, radio clock) 2-255, secondary reference (via NTP)

OBJECT-TYPE

The IP address of the reference clock ip address.

OBJECT-TYPE

The frequency of local clock relative to the primary reference source.

OBJECT-TYPE

Precision : This is a signed integer indicating the precision relative to the reference clock ip.

OBJECT-TYPE

This is the local time.

OBJECT-TYPE

This is a signed fixed-point number indicating the total roundtrip delay to the primary reference source at the root of the synchronization subnet, in seconds.

OBJECT-TYPE

Root Dispersion : This is a signed fixed-point number indicating the maximum error relative to the primary reference source at the root of the synchronization subnet, in seconds.Only positive values greater than zero are possible.

OBJECT-TYPE

This is a signed fixed-point number indicating the maximum error of the local clock relative to the primary reference source at the root of the synchronization subnet.Only positive values greater than zero are possible.

OBJECT-TYPE

This is a signed, fixed-point number indicating the offset of the local clock relative to the primary clock, in seconds.

OBJECT-TYPE

This is a signed, fixed-point number indicating the stability of the local clock relative to the primary clock, in seconds.

OBJECT-TYPE

This table provides information about the peers and servers with which the local NTP has associations.

OBJECT-TYPE

Each association entry provides NTP information retrieved from a particular initiative peer or server.Each peer or server is identified by a unique association identifier. Entries are automatically created when the user configures the passive peer to unicast peer list or the passive server to unicast server list.

OBJECT-TYPE

The IP address of the initiative peer or server.

OBJECT-TYPE

The reference identifier of the peer or server.

OBJECT-TYPE

This is a integer indicating the stratum level of the peer of server clock.

OBJECT-TYPE

This is a round second clock whose value change from 1 to 60.

OBJECT-TYPE

The interval at which the local host polls the peer.

OBJECT-TYPE

This is a shift register of NTP which is used to determine the reach abilityStatus of the peer.

OBJECT-TYPE

This is a signed fixed-point number indicating the total roundtrip delay to the primary reference source at the root of the synchronization subnet, in seconds.

OBJECT-TYPE

This is a signed, fixed-point number indicating the offset of the peer clock or server clock relative to the local clock, in seconds.

OBJECT-TYPE

This is a signed fixed-point number indicating the maximum error of the peer or server clock relative to the primary reference source.

OBJECT-TYPE

This table provides ipaddress about the peer with which the local NTP has associations.This Table support create and destroy association peer entry.

OBJECT-TYPE

This table provides ipaddress about the peer with which the local NTP has associations.This table support create and destroy association peer entry.

OBJECT-TYPE

The IP address of the initiative peer.

OBJECT-TYPE

The peer use which authentication key pair.

OBJECT-TYPE

The NTP verion of the peer.

OBJECT-TYPE

This indicates the NTP peer is a preferred peer.

OBJECT-TYPE

The status of this conceptual row.Now only realize CreateAndGo and Destroy and Active. 1 means Active 4 means CreateAndGo 6 means Destroy

OBJECT-TYPE

This table provides ipaddress about the server with which the local NTP has associations.This table support create and destroy association server entry.

OBJECT-TYPE

This table provides ipaddress about the server with which the local NTP has associations.This table support create and destroy association server entry.

OBJECT-TYPE

The IP address of the initiative server.

OBJECT-TYPE

The server use which authentication key pair.

OBJECT-TYPE

The NTP verion of the server.

OBJECT-TYPE

This indicates the NTP server is a preferred server.

OBJECT-TYPE

The status of this conceptual row.Now only realize CreateAndGo and Destroy and Active. 1 means Active 4 means CreateAndGo 6 means Destroy

OBJECT-TYPE

The stratum of local reference clock.If the value is 16, disable local reference clock.

OBJECT-TYPE

This is a integer indicating that system support authentication.

OBJECT-TYPE

The broadcast delay of ntp broadcast mode.

OBJECT-TYPE

The table containing information of authentication key pair.

OBJECT-TYPE

An entry containing information of authentication key pair.

OBJECT-TYPE

NTP authentication key ID

OBJECT-TYPE

NTP authentication key pair.

OBJECT-TYPE

The status of this conceptual row.Now only realize CreateAndGo and Destroy and Active. 1 means Active 4 means CreateAndGo 6 means Destroy

OBJECT-TYPE

The table containing information of authentication key pair that trusted.

OBJECT-TYPE

An entry containing information of authentication key pair that trusted.

OBJECT-TYPE

NTP authentication key ID

OBJECT-TYPE

NTP authentication key pair trust.

OBJECT-TYPE

Reload interfaces.

OBJECT-TYPE

NTP I/O statistics of time since reset.

OBJECT-TYPE

NTP I/O statistics of receive buffers.

OBJECT-TYPE

NTP I/O statistics of free receive buffers.

OBJECT-TYPE

NTP I/O statistics of used receive buffers.

OBJECT-TYPE

NTP I/O statistics of low water refills.

OBJECT-TYPE

NTP I/O statistics of dropped packets.

OBJECT-TYPE

NTP I/O statistics of ignored packets.

OBJECT-TYPE

NTP I/O statistics of received packets.

OBJECT-TYPE

NTP I/O statistics of packets sent.

OBJECT-TYPE

NTP I/O statistics of packets not sent.

OBJECT-TYPE

NTP I/O statistics of interrupts handled.

OBJECT-TYPE

NTP I/O statistics of received by int.

OBJECT-TYPE

The table create the Access Control Entries (ACE) of a NTP server/peer.

OBJECT-TYPE

An entry containing information of NTP ACE.

OBJECT-TYPE

NTP ace list index.

OBJECT-TYPE

Ip address or hostname of NTP restrict peer.

OBJECT-TYPE

Mask of NTP restrict peer. Default value is 255.255.255.255

OBJECT-TYPE

Ignore these hosts if not the current NTP version.enable(1),disable(2).

OBJECT-TYPE

If access is denied, send a kiss-of-death packet.

OBJECT-TYPE

Ignore all packets from host that match this entry.

OBJECT-TYPE

Ignore all NTP mode 6 and 7 packets from the source. Time service is not affected.

OBJECT-TYPE

Ignore all NTP mode 6 and 7 packets which attempt to modify the stateof the server.

OBJECT-TYPE

Decline to provide mode 6 control message trap service to matching hosts.

OBJECT-TYPE

Ignore NTP packets whose mode is other than 6 or 7.

OBJECT-TYPE

Provide stateless time service to polling hosts, but do not allocate peer memory resources.

OBJECT-TYPE

Treat these hosts normally in other respects, but never use them as synchronization sources.

OBJECT-TYPE

These hosts are subject to limitation of number of clients from the same net.

OBJECT-TYPE

The status of this conceptual row.Now only realize CreateAndGo and Destroy and Active. 1 means Active 4 means CreateAndGo 6 means Destroy

OBJECT-TYPE

The table containing information of NTP current restrict list.

OBJECT-TYPE

An entry containing information of NTP restrict.

OBJECT-TYPE

NTP current restrict list index.

OBJECT-TYPE

NTP current restrict address.

OBJECT-TYPE

NTP current restrict mask.

OBJECT-TYPE

NTP current restrict count value.

OBJECT-TYPE

NTP current restrict flags.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

Configure the match-order of number-acl group.

OBJECT-TYPE

Define the index of aclGroupTable.

OBJECT-TYPE

The index of acl group. MAC type :10001..20000 IP Extend type :20001..30000 IP type :30001..40000 IPv6 type :40001..50000 IPv6 Extend type :50001..60000 MLPS type :60001..70000 MPLS Extend type :70001..80000.

OBJECT-TYPE

The name of acl group. Range 0~20.

OBJECT-TYPE

The count of rules in this acl group.

OBJECT-TYPE

The status of this row.Now only realize CreateAndGo and Destroy and Active. 1 means Active 4 means CreateAndGo 6 means Destroy

OBJECT-TYPE

The description of this acl group.Up to 100 characters.Range 0~100.

OBJECT-TYPE

A table of MAC acl group. If some objects of this table are not supported by some products, these objects can't be created, changed and applied. Default value of these objects will be returned when they are read.

OBJECT-TYPE

MAC acl group information.

OBJECT-TYPE

The index of MAC-based acl group.Range is 10001~30000 and 50001~60000.

OBJECT-TYPE

The rule index of MAC-based acl group. Range 1~131071.

OBJECT-TYPE

The action of MAC acl rule. (1) permit. (2) deny.

OBJECT-TYPE

Source MAC of MAC acl rule. If you do not want to use this filter, set this item with any valid value and set aclMacSrcMacWild 'FFFF.FFFF.FFFF'.

OBJECT-TYPE

Source MAC wildcard of MAC acl rule. If you do not want to use this filter, set aclMacSrcMac with any valid value and set this item 'FFFF.FFFF.FFFF'.

OBJECT-TYPE

Destination MAC of MAC acl rule. If you do not want to use this filter, set this item with any valid value and set aclMacDestMacWild 'FFFF.FFFF.FFFF'.

OBJECT-TYPE

Destination MAC wildcard of MAC acl rule. If you do not want to use this filter, set aclMacDestMac with any valid value and set this item 'FFFF.FFFF.FFFF'.

OBJECT-TYPE

Ether type in decimal/hexadecimal, ranging in <0x0-0xffff>. (aclMacProtocol = 0, aclMacProtocolWild = 0xffff) means any protocols.

OBJECT-TYPE

Ether type wildcard in decimal/hexadecimal, ranging in <0x0-0xffff>, reversely encoded. (aclMacProtocol = 0, aclMacProtocolWild = 0xffff) means any protocols.

OBJECT-TYPE

The type of protocol nouse(0) eth2(1) sap(2) snap(3)

OBJECT-TYPE

The vlan id of MAC acl rule.Range 0~4094. nouse(0)

OBJECT-TYPE

The inner vlan id of MAC acl rule. Range 0~4094 nouse(0)

OBJECT-TYPE

Vlan priority of MAC acl rule.Range 0~8 nouse(8).

OBJECT-TYPE

Inner vlan priority of MAC acl rule.Range 0~8. nouse(8).

OBJECT-TYPE

The Time-range of MAC acl rule.Range 0~20.

OBJECT-TYPE

The status of this row.Now only realize CreateAndGo and Destroy and Active. 1 means Active 4 means CreateAndGo 6 means Destroy

OBJECT-TYPE

Configure the rule for ip acl group.

OBJECT-TYPE

Define the index of aclIpRuleTable.

OBJECT-TYPE

The index of ip acl group. Range 20001~40000.

OBJECT-TYPE

The rule index of ip acl rule.Range 1~131071.

OBJECT-TYPE

The action of ip acl rule. (1) permit. (2) deny.

OBJECT-TYPE

The protocol-type of Ip acl group. <0-255> Protocol number Icmp Internet Control Message Protocol(1) igmp Internet Group Management Protocol(2) ospf OSPF routing protocol(89) tcp Transmission Control Protocol (6) udp User Datagram Protocol (17) nouse Do not use this filter(256)

OBJECT-TYPE

Source IP-address of ip acl group.

OBJECT-TYPE

Source IP-address wild of ip acl group.

OBJECT-TYPE

Destination IP-address of ip acl group.

OBJECT-TYPE

Destination IP-address wild of ip acl group.

OBJECT-TYPE

The value of Precedence.8 means do not use this filter.Range 0~8. DSCP and Precedence both use IP TOS segment.This node can not be setted for aclIpDscp is setted.

OBJECT-TYPE

The value of DSCP.64 means do not use this filter. DSCP and Precedence both use IP TOS segment.This node can not be setted for aclIpPrecedence is setted.

OBJECT-TYPE

The flag of matching fragmented packet. True(1),False(2).

OBJECT-TYPE

The flag of matching routed packet. True(1),False(2).

OBJECT-TYPE

The flag of matching packet with ip option. True(1),False(2).

OBJECT-TYPE

The Time-range of Ip acl rule.String length range 0~20.

OBJECT-TYPE

The status of this conceptual row.Now only realize CreateAndGo and Destroy and Active. 1 means Active 4 means CreateAndGo 6 means Destroy

OBJECT-TYPE

Configure the rule for tcp acl group.

OBJECT-TYPE

Define the index of hh3cAclTcpRuleTable.

OBJECT-TYPE

The index of tcp acl group. Range 20001~40000.

OBJECT-TYPE

The rule index of tcp acl group. Range 1~131071.

OBJECT-TYPE

The action of tcp acl rule. (1) permit. (2) deny.

OBJECT-TYPE

Source IP-address of tcp acl group.

OBJECT-TYPE

Source IP-address wild of tcp acl group.

OBJECT-TYPE

Destination IP-address of tcp acl group.

OBJECT-TYPE

Destination IP-address wild of tcp acl group.

OBJECT-TYPE

The value of Precedence.8 means do not use this filter.Range 0~8. DSCP and Precedence both use IP TOS segment.This node can not be setted for aclTcpDscp is setted.

OBJECT-TYPE

The value of DSCP.64 means do not use this filter. DSCP and Precedence both use IP TOS segment.This node can not be setted for aclTcpPrecedence is setted.

OBJECT-TYPE

The flag of matching fragmented packet. True(1),False(2). This node can not be setted true for aclTcpSrcOp or aclTcpDestOp is setted.

OBJECT-TYPE

The flag of matching routed packet. True(1),False(2).

OBJECT-TYPE

The flag of matching packet with ip option. True(1),False(2).

OBJECT-TYPE

The source port's operator of tcp acl group. This node can not be setted if aclTcpFragments is true. eq(0), gt(2), lt(3), range(4), invalid(5)

OBJECT-TYPE

The fourth layer source port1. Range 0~65535.

OBJECT-TYPE

The fourth layer source port2. Range 0~65535.

OBJECT-TYPE

The destination port's operator of tcp acl group. This node can not be setted if aclTcpFragments is true. eq(0), gt(2), lt(3), range(4), invalid(5)

OBJECT-TYPE

The fourth layer destination port1. Range 0~65535.

OBJECT-TYPE

The fourth layer destination port2. Range 0~65535.

OBJECT-TYPE

The tcp-flags' operator of tcp acl group.for example, established tcp packet with ack or rst flag setted, set this node matchAny(0) and set aclTcpFlagAck and aclTcpFlagRst can filter established tcp packet. matchAny(0), matchAll(1), invalid(2).

OBJECT-TYPE

The tcp-urg flag of tcp acl group. True(1),False(2). TCP protocol URG Packet.

OBJECT-TYPE

The tcp-ack flag of tcp acl group. TCP protocol ACK Packet. True(1),False(2).

OBJECT-TYPE

The tcp-psh flag of tcp acl group. True(1),False(2). TCP protocol PSH Packet.

OBJECT-TYPE

The tcp-rst flag of tcp acl group. True(1),False(2). TCP protocol RST Packet.

OBJECT-TYPE

The tcp-syn flag of tcp acl group. True(1),False(2). TCP protocol SYN Packet.

OBJECT-TYPE

The tcp-fin flag of tcp acl group. True(1),False(2). TCP protocol FIN Packet.

OBJECT-TYPE

The Time-range of tcp acl rule.

OBJECT-TYPE

The status of this conceptual row.Now only realize CreateAndGo and Destroy and Active. 1 means Active 4 means CreateAndGo 6 means Destroy

OBJECT-TYPE

Configure the rule for udp acl group.

OBJECT-TYPE

Define the index of aclUdpRuleTable.

OBJECT-TYPE

The index of udp acl group. Range 20001~40000.

OBJECT-TYPE

The rule index of udp acl group. Range 1~131071.

OBJECT-TYPE

The action of udp acl rule. (1) permit. (2) deny

OBJECT-TYPE

Source IP-address of udp acl group.

OBJECT-TYPE

Source IP-address wild of udp acl group.

OBJECT-TYPE

Destination IP-address of udp acl group.

OBJECT-TYPE

Destination IP-address wild of udp acl group.

OBJECT-TYPE

The value of Precedence.8 means do not use this filter.Range 0~8. DSCP and Precedence both use IP TOS segment.This node can not be setted for aclUdpDscp is setted.

OBJECT-TYPE

The value of DSCP.64 means do not use this filter. DSCP and Precedence both use IP TOS segment.This node can not be setted for aclUdpPrecedence is setted.

OBJECT-TYPE

The flag of matching fragmented packet. True(1),False(2). This node can not be setted true for aclUdpSrcOp or aclUdpDestOp is setted.

OBJECT-TYPE

The flag of matching routed packet. True(1),False(2).

OBJECT-TYPE

The flag of matching packet with ip option. True(1),False(2).

OBJECT-TYPE

The source port's operator of udp acl group. This node can not be setted if aclUdpFragments is true. eq(0), gt(2), lt(3), range(4), invalid(5)

OBJECT-TYPE

The fourth layer source port1. Range 0~65535.

OBJECT-TYPE

The fourth layer source port2. Range 0~65535.

OBJECT-TYPE

The destination port's operator of udp acl group. This node can not be setted if aclUdpFragments is true. eq(0), gt(2), lt(3), range(4), invalid(5)

OBJECT-TYPE

The fourth layer destination port1. Range 0~65535.

OBJECT-TYPE

The fourth layer destination port2. Range 0~65535.

OBJECT-TYPE

The Time-range of udp acl rule. Range 0~20.

OBJECT-TYPE

The status of this conceptual row.Now only realize CreateAndGo and Destroy and Active. 1 means Active 4 means CreateAndGo 6 means Destroy

OBJECT-TYPE

Configure the rule for icmp acl group.

OBJECT-TYPE

Define the index of aclIcmpRuleTable.

OBJECT-TYPE

The index of icmp acl group. Range 20001~40000.

OBJECT-TYPE

The rule index of icmp acl group. Range 1~131071.

OBJECT-TYPE

The action of icmp acl rule. (1) permit. (2) deny

OBJECT-TYPE

Source IP-address of icmp acl group.

OBJECT-TYPE

Source IP-address wild of icmp acl group.

OBJECT-TYPE

Destination IP-address of icmp acl group.

OBJECT-TYPE

Destination IP-address wild of icmp acl group.

OBJECT-TYPE

The value of Precedence.8 means do not use this filter.Range 0~8. DSCP and Precedence both use IP TOS segment.This node can not be setted for aclIcmpDscp is setted.

OBJECT-TYPE

The value of DSCP.64 means do not use this filter. DSCP and Precedence both use IP TOS segment.This node can not be setted for aclIcmpPrecedence is setted.

OBJECT-TYPE

The flag of matching fragmented packet. This node can not be setted true if aclIcmpType is setted. True(1),False(2).

OBJECT-TYPE

The flag of matching routed packet. True(1),False(2).

OBJECT-TYPE

The flag of matching packet with ip option. True(1),False(2).

OBJECT-TYPE

The type of ICMP packet. INTEGER<0-256> ICMP type echo Type=8, Code=0 echo-reply Type=0, Code=0 fragmentneed-DFset Type=3, Code=4 host-redirect Type=5, Code=1 host-tos-redirect Type=5, Code=3 host-unreachable Type=3, Code=1 information-reply Type=16, Code=0 information-request Type=15, Code=0 net-redirect Type=5, Code=0 net-tos-redirect Type=5, Code=2 net-unreachable Type=3, Code=0 parameter-problem Type=12, Code=0 port-unreachable Type=3, Code=3 protocol-unreachable Type=3, Code=2 reassembly-timeout Type=11, Code=1 source-quench Type=4, Code=0 source-route-failed Type=3, Code=5 timestamp-reply Type=14, Code=0 timestamp-request Type=13, Code=0 ttl-exceeded Type=11, Code=0 nouse 256 This node can not be setted if aclIcmpFragments is true.

OBJECT-TYPE

The code of ICMP packet.INTEGER<0-256> echo Type=8, Code=0 echo-reply Type=0, Code=0 fragmentneed-DFset Type=3, Code=4 host-redirect Type=5, Code=1 host-tos-redirect Type=5, Code=3 host-unreachable Type=3, Code=1 information-reply Type=16, Code=0 information-request Type=15, Code=0 net-redirect Type=5, Code=0 net-tos-redirect Type=5, Code=2 net-unreachable Type=3, Code=0 parameter-problem Type=12, Code=0 port-unreachable Type=3, Code=3 protocol-unreachable Type=3, Code=2 reassembly-timeout Type=11, Code=1 source-quench Type=4, Code=0 source-route-failed Type=3, Code=5 timestamp-reply Type=14, Code=0 timestamp-request Type=13, Code=0 ttl-exceeded Type=11, Code=0 nouse 256 This node can not be setted if aclIcmpType is not setted.

OBJECT-TYPE

The Time-range of icmp acl rule. Range 0~20.

OBJECT-TYPE

The status of this conceptual row.Now only realize CreateAndGo and Destroy and Active. 1 means Active 4 means CreateAndGo 6 means Destroy

OBJECT-TYPE

Configure the rule for igmp acl group.

OBJECT-TYPE

Define the index of aclIgmpRuleTable.

OBJECT-TYPE

The index of igmp acl group. Range 20001~40000.

OBJECT-TYPE

The rule index of igmp acl group.Range 1~131071.

OBJECT-TYPE

The action of igmp acl rule. (1) permit. (2) deny

OBJECT-TYPE

Source IP-address of igmp acl group.

OBJECT-TYPE

Source IP-address wild of igmp acl group.

OBJECT-TYPE

Destination IP-address of igmp acl group.

OBJECT-TYPE

Destination IP-address wild of igmp acl group.

OBJECT-TYPE

The value of Precedence.8 means do not use this filter.Range 0~8. DSCP and Precedence both use IP TOS segment.This node can not be setted for aclIgmpDscp is setted.

OBJECT-TYPE

The value of DSCP.64 means do not use this filter. DSCP and Precedence both use IP TOS segment.This node can not be setted for aclIgmpPrecedence is setted.

OBJECT-TYPE

The flag of matching fragmented packet. This node can not be setted true if aclIgmpType is setted. True(1),False(2).

OBJECT-TYPE

The flag of matching routed packet. True(1),False(2).

OBJECT-TYPE

The flag of matching packet with ip option.True(1),False(2).

OBJECT-TYPE

The type of ICMP packet. 0 precedence 17 host query 18 host report 19 dvmrp 20 pim 21 trace 22 v2 report 23 v2 leave 30 mtrace response 31 mtrace 34 v3 report 256 nouse This node can not be setted if aclIgmpFragments is true.

OBJECT-TYPE

The Time-range of igmp acl rule.Range 0~20.

OBJECT-TYPE

The status of this conceptual row.Now only realize CreateAndGo and Destroy and Active. 1 means Active 4 means CreateAndGo 6 means Destroy

OBJECT-TYPE

A table of MPLS MAC acl group. If some objects of this table are not supported by some products, these objects can't be created, changed and applied. Default value of these objects will be returned when they are read.

OBJECT-TYPE

MPLS MAC acl group information.

OBJECT-TYPE

The index of MPLS MAC-based acl group. Range 70001 ~ 80000.

OBJECT-TYPE

The rule index of MPLS MAC-based acl group. Range 1~131071.

OBJECT-TYPE

The action of MPLS MAC acl rule. (1) permit. (2) deny.

OBJECT-TYPE

Source MAC of MPLS MAC acl rule.

OBJECT-TYPE

Source MAC wildcard of MPLS MAC acl rule.

OBJECT-TYPE

Destination MAC of MAC acl rule. If you do not want to use this filter, set this item and aclMacDestMacWild 'FF:FF:FF:FF:FF:FF'.

OBJECT-TYPE

Destination MAC wildcard of MAC acl rule. If you do not want to use this filter, set this item and aclMacDestMac 'FF:FF:FF:FF:FF:FF'.

OBJECT-TYPE

The type of protocol nouse(0) eth2(1) sap(2) snap(3)

OBJECT-TYPE

The vlan id of MAC acl rule.Range 0~4094. nouse(0)

OBJECT-TYPE

The inner vlan id of MAC acl rule. nouse(0)

OBJECT-TYPE

Vlan priority of MAC acl rule.Range 0~8 nouse(8).

OBJECT-TYPE

Inner vlan priority of MAC acl rule. nouse(8).

OBJECT-TYPE

The Time-range of MAC acl rule.

OBJECT-TYPE

The status of this row.Now only realize CreateAndGo and Destroy and Active.

OBJECT-TYPE

Configure the rule for Mpls Label acl group.

OBJECT-TYPE

Define the index of acl Mpls Label RuleTable.

OBJECT-TYPE

The index of MplsLabel acl group. Range 60001~80000.

OBJECT-TYPE

The rule index of MplsLabel acl rule.Range 1~131071.

OBJECT-TYPE

The action of MplsLabel acl rule. (1) permit. (2) deny.

OBJECT-TYPE

The layer number of MPLS labels.Range is <1-4>. Set 1 means match MPLS packets with more than (or equal to) one layer MPLS label. Set 2 means match MPLS packets with more than (or equal to) two layer MPLS label. Set 3 means match MPLS packets with more than (or equal to) three layer MPLS label. Set 4 means match MPLS packets with more than (or equal to) four layer MPLS label.

OBJECT-TYPE

The mpls label1 value in in decimal system. Range is 0~1048575.Default value is 0.

OBJECT-TYPE

MPLS label wildcard in hexadecimal system. Range is string 0~fffff. Default wild value is fffff, means any.

OBJECT-TYPE

The exp value of the MPLS label.Range of exp is <0-7>. 8 means do not use.Default value is 8.

OBJECT-TYPE

The ttl value of the MPLS label.Range of ttl is <0-255>. 256 means do not use.Default value is 256.

OBJECT-TYPE

The mpls label value in in decimal system. Range is 0~1048575.Default value is 0.

OBJECT-TYPE

MPLS label wildcard in hexadecimal system. Range is string 0~fffff. Defalut wild value is fffff, means any.

OBJECT-TYPE

The exp value of the MPLS label.Range of exp is <0-7>. 8 means do not use.Default value is 8.

OBJECT-TYPE

The ttl value of the MPLS label.Range of ttl is <0-255>. 256 means do not use.Default value is 256.

OBJECT-TYPE

The mpls label value in in decimal system. Range is 0~1048575.Default value is 0.

OBJECT-TYPE

MPLS label wildcard in hexadecimal system. Range is string 0~fffff. Default wild value is fffff, means any.

OBJECT-TYPE

The exp value of the MPLS label.Range of exp is <0-7>. 8 means do not use.Default value is 8.

OBJECT-TYPE

The ttl value of the MPLS label.Range of ttl is <0-255>. 256 means do not use.Default value is 256.

OBJECT-TYPE

The mpls label value in in decimal system. Range is 0~1048575.Default value is 0.

OBJECT-TYPE

MPLS label wildcard in hexadecimal system. Range is string 0~fffff. Default wild value is fffff, means any.

OBJECT-TYPE

The exp value of the MPLS label.Range of exp is <0-7>. 8 means do not use.Default value is 8.

OBJECT-TYPE

The ttl value of the MPLS label.Range of ttl is <0-255>. 256 means do not use.Default value is 256.

OBJECT-TYPE

Set whether the topmost label as bottom of label stack. True(1), means matching MPLS packets with label layer num equal to aclMplsLabelLayer. False(2), means matching MPLS packets with label layer num more than aclMplsLabelLayer. Default value is False.

OBJECT-TYPE

The Time-range of used by the MPLS filter rule.

OBJECT-TYPE

The status of this conceptual row.Now only realize CreateAndGo and Destroy and Active.

OBJECT-TYPE

Configure the rule for ipv6 acl group.

OBJECT-TYPE

Define the index of aclIpv6RuleTable.

OBJECT-TYPE

The index of ipv6 acl group. Range 40001~60000.

OBJECT-TYPE

The rule index of ipv6 acl rule.Range 1~131071.

OBJECT-TYPE

The action of ipv6 acl rule. (1) permit. (2) deny.

OBJECT-TYPE

The protocol-type of Ipv6 acl group. <0-255> Protocol number Icmpv6 Internet Control Message Protocol(58) ospf OSPF routing protocol(89) tcp Transmission Control Protocol (6) udp User Datagram Protocol (17) nouse Do not use this filter(256)

OBJECT-TYPE

Source IPv6-address of ipv6 acl group.

OBJECT-TYPE

Source IPv6-address prefix length of ipv6 acl group.Range 0~128

OBJECT-TYPE

Destination IPv6-address of ipv6 acl group.

OBJECT-TYPE

Destination IPv6-address prefix length of ipv6 acl group.Range 0~128

OBJECT-TYPE

The value of FlowLabel.1048576 means do not use this filter.Range 0~1048576.

OBJECT-TYPE

The value of DSCP.64 means do not use this filter.Range 0~64.

OBJECT-TYPE

The flag of matching fragmented packet. True(1),False(2).

OBJECT-TYPE

The flag of matching routed packet. True(1),False(2).

OBJECT-TYPE

The flag of matching packet with ipv6 option. True(1),False(2).

OBJECT-TYPE

The Time-range of Ipv6 acl rule.String length range 0~20.

OBJECT-TYPE

The status of this conceptual row.Now only realize CreateAndGo and Destroy and Active.

OBJECT-TYPE

Configure the rule for tcp6 acl group.

OBJECT-TYPE

Define the index of aclTcp6RuleTable.

OBJECT-TYPE

The index of tcp6 acl group. Range 40001~60000.

OBJECT-TYPE

The rule index of tcp6 acl group. Range 1~131071.

OBJECT-TYPE

The action of tcp6 acl rule. (1) permit. (2) deny.

OBJECT-TYPE

Source IPv6-address of tcp6 acl group.

OBJECT-TYPE

Source IPv6-address prefix length of tcp6 acl group.Range 0~128

OBJECT-TYPE

Destination IPv6-address of tcp6 acl group.

OBJECT-TYPE

Destination IPv6-address prefix length of tcp6 acl group.Range 0~128

OBJECT-TYPE

The value of FlowLabel.1048576 means do not use this filter.Range 0~1048576.

OBJECT-TYPE

The value of DSCP.64 means do not use this filter.Range 0~64.

OBJECT-TYPE

The flag of matching fragmented packet. True(1),False(2). This node can not be setted true for aclTcp6SrcOp or aclTcp6DestOp is setted.

OBJECT-TYPE

The flag of matching routed packet. True(1),False(2).

OBJECT-TYPE

The flag of matching packet with ipv6 option. True(1),False(2).

OBJECT-TYPE

The source port's operator of tcp6 acl group. This node can not be setted if aclTcp6Fragments is true. eq(0), gt(2), lt(3), range(4), invalid(5)

OBJECT-TYPE

The fourth layer source port1. Range 0~65535.

OBJECT-TYPE

The fourth layer source port2. Range 0~65535.

OBJECT-TYPE

The destination port's operator of tcp6 acl group. This node can not be setted if aclTcp6Fragments is true. eq(0), gt(2), lt(3), range(4), invalid(5)

OBJECT-TYPE

The fourth layer destination port1. Range 0~65535.

OBJECT-TYPE

The fourth layer destination port2. Range 0~65535.

OBJECT-TYPE

The tcp-flags' operator of tcp6 acl group. for example, established tcp packet with ack or rst flag setted, set this node matchAny(0) and set aclTcp6FlagAck and aclTcp6FlagRst can filter established tcp packet. matchAny(0), matchAll(1), invalid(2).

OBJECT-TYPE

The tcp-urg flag of tcp6 acl group. True(1),False(2). TCP protocol URG Packet.

OBJECT-TYPE

The tcp-ack flag of tcp6 acl group. TCP protocol ACK Packet. True(1),False(2).

OBJECT-TYPE

The tcp-psh flag of tcp6 acl group. True(1),False(2). TCP protocol PSH Packet.

OBJECT-TYPE

The tcp-rst flag of tcp6 acl group. True(1),False(2). TCP protocol RST Packet.

OBJECT-TYPE

The tcp-syn flag of tcp6 acl group. True(1),False(2). TCP protocol SYN Packet.

OBJECT-TYPE

The tcp-fin flag of tcp6 acl group. True(1),False(2). TCP protocol FIN Packet.

OBJECT-TYPE

The Time-range of tcp6 acl rule.

OBJECT-TYPE

The status of this conceptual row.Now only realize CreateAndGo and Destroy and Active.

OBJECT-TYPE

Configure the rule for udp6 acl group.

OBJECT-TYPE

Define the index of aclUdp6RuleTable.

OBJECT-TYPE

The index of udp6 acl group. Range 40001~60000.

OBJECT-TYPE

The rule index of udp6 acl group. Range 1~131071.

OBJECT-TYPE

The action of udp6 acl rule. (1) permit. (2) deny

OBJECT-TYPE

Source IPv6-address of udp6 acl group.

OBJECT-TYPE

Source IPv6-address prefix length of udp6 acl group.Range 0~128

OBJECT-TYPE

Destination IPv6-address of udp6 acl group.

OBJECT-TYPE

Destination IPv6-address prefix length of udp6 acl group.Range 0~128

OBJECT-TYPE

The value of FlowLabel.1048576 means do not use this filter.Range 0~1048576.

OBJECT-TYPE

The value of DSCP.64 means do not use this filter.Range 0~64.

OBJECT-TYPE

The flag of matching fragmented packet. True(1),False(2). This node can not be setted true for aclUdp6SrcOp or aclUdp6DestOp is setted.

OBJECT-TYPE

The flag of matching routed packet. True(1),False(2).

OBJECT-TYPE

The flag of matching packet with ipv6 option. True(1),False(2).

OBJECT-TYPE

The source port's operator of udp6 acl group. This node can not be setted if aclUdp6Fragments is true. eq(0), gt(2), lt(3), range(4), invalid(5)

OBJECT-TYPE

The fourth layer source port1. Range 0~65535.

OBJECT-TYPE

The fourth layer source port2. Range 0~65535.

OBJECT-TYPE

The destination port's operator of udp6 acl group. This node can not be setted if aclUdp6Fragments is true. eq(0), gt(2), lt(3), range(4), invalid(5)

OBJECT-TYPE

The fourth layer destination port1. Range 0~65535.

OBJECT-TYPE

The fourth layer destination port2. Range 0~65535.

OBJECT-TYPE

The Time-range of udp6 acl rule. Range 0~20.

OBJECT-TYPE

The status of this conceptual row.Now only realize CreateAndGo and Destroy and Active.

OBJECT-TYPE

Configure the rule for icmp6 acl group.

OBJECT-TYPE

Define the index of aclIcmp6RuleTable.

OBJECT-TYPE

The index of icmp6 acl group. Range 40001~60000.

OBJECT-TYPE

The rule index of icmp6 acl group. Range 1~131071.

OBJECT-TYPE

The action of icmp6 acl rule. (1) permit. (2) deny

OBJECT-TYPE

Source IPv6-address of icmp6 acl group.

OBJECT-TYPE

Source IPv6-address prefix length of icmp6 acl group.Range 0~128

OBJECT-TYPE

Destination IPv6-address of icmp6 acl group.

OBJECT-TYPE

Destination IPv6-address prefix length of icmp6 acl group.Range 0~128

OBJECT-TYPE

The value of FlowLabel.1048576 means do not use this filter.Range 0~1048576.

OBJECT-TYPE

The value of DSCP.64 means do not use this filter.Range 0~64.

OBJECT-TYPE

The flag of matching fragmented packet. This node can not be setted true if aclIcmp6Type is setted. True(1),False(2).

OBJECT-TYPE

The flag of matching routed packet. True(1),False(2).

OBJECT-TYPE

The flag of matching packet with ipv6 option. True(1),False(2).

OBJECT-TYPE

The type of ICMPv6 packet.Range 0~256. This node can not be setted if aclIcmp6Fragments is true.

OBJECT-TYPE

The code of ICMPv6 packet.Range 0~256. This node can not be setted if aclIcmp6Type is not setted.

OBJECT-TYPE

The Time-range of icmp6 acl rule. Range 0~20.

OBJECT-TYPE

The status of this conceptual row.Now only realize CreateAndGo and Destroy and Active.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

Enable/disable qos globally. enable(1),disable(2).

OBJECT-TYPE

Set 'true(1)' for flow policer first, 'false(2)' for port policer first. Default value is false(2).

OBJECT-IDENTITY

OBJECT-TYPE

Reset configuration of qos maping table in specified domain.

OBJECT-TYPE

Entry of globalQosResetDomainMapTable.

OBJECT-TYPE

Qos domain.Range is <0-7>.

OBJECT-TYPE

Restore the whole running map table to system default table. Set the value to restore related table. cosPriColor(1) Restore the COS-to-Priority/Color map dscpPriColor(2) Restore dscp-priority-color map expPriColor(3) Restore the exp-to-priority/color map ipPrecPriColor(4) Restore the IP Precedence to Pri/Color map priColorCos(5) Restore PRI_COLOR-to-COS map priColorDscp(6) Restore PRI_COLOR-to-DSCP map priColorExp(7) Restore PRI_COLOR-to-EXP map The get of this value alway return 0

OBJECT-TYPE

Set 1 to reset priority-color-queueId-thresholdId mapping. Zero will be returned.

OBJECT-IDENTITY

OBJECT-TYPE

Running table of interface ingress map.

OBJECT-TYPE

Entry of globalQosMapIngressTable.

OBJECT-TYPE

Type of map. cos(1), dscp(2), exp(3), ipPre(4)

OBJECT-TYPE

Ingress domain. Range is <0-7>.

OBJECT-TYPE

Different type has different GlobalQosMapIngressValue. Type-name Range of GlobalQosMapIngressValue cos (0..7) dscp (0..63) ipPre (0..7) exp (0..7)

OBJECT-TYPE

Internal priority value.Range is <0-63>.

OBJECT-TYPE

Internal color.Set (1)red, (2)yellow, (3)green.

OBJECT-TYPE

Running table of interface egress map.

OBJECT-TYPE

Entry of globalQosMapEgressTable

OBJECT-TYPE

Type of the egress map-table. Only value cos(1), dscp(2), exp(3) can be use.

OBJECT-TYPE

Egress domain.Range is <0-7>.

OBJECT-TYPE

Internal priority value.Range is <0-63>.

OBJECT-TYPE

Internal color. Set (1)red, (2)yellow, (3)green.

OBJECT-TYPE

Different type has different GlobalQosMapIngressValue. Type-name Range of GlobalQosMapIngressValue cos (0..7) dscp (0..63) exp (0..7)

OBJECT-TYPE

A table of qos map priority-color to QueueId - thresholdId.

OBJECT-TYPE

Entry of globalQosMapPriColorQidTidTable.

OBJECT-TYPE

QoS Map Priority to be configured.Range is <0-63>.

OBJECT-TYPE

Internal color. Set (1)red, (2)yellow, (3)green.

OBJECT-TYPE

The queue id to be mapped to.Range is <0-7>.

OBJECT-TYPE

The threasholdId id to be mapped to.Range is <0-3>.

OBJECT-TYPE

A table of interface ingress map.

OBJECT-TYPE

Entry of globalQosMapIngressDefaultTable.

OBJECT-TYPE

Type of map. cos(1), dscp(2), exp(3), ipPre(4)

OBJECT-TYPE

Ingress domain.

OBJECT-TYPE

Different type has different GlobalQosMapIngressValue. Type-name Range of GlobalQosMapIngressValue cos (0..7) dscp (0..63) ipPre (0..7) exp (0..7)

OBJECT-TYPE

Internal priority value.

OBJECT-TYPE

Internal color.Set (1)red, (2)yellow, (3)green.

OBJECT-TYPE

A table of interface egress map.

OBJECT-TYPE

Entry of globalQosMapEgressDefaultTable.

OBJECT-TYPE

Type of the egress map-table. Only valude cos(1), dscp(2), exp(3) can be use.

OBJECT-TYPE

Egress domain.

OBJECT-TYPE

Internal priority value.

OBJECT-TYPE

Internal color. Set (1)red, (2)yellow, (3)green.

OBJECT-TYPE

Different type has different GlobalQosMapIngressValue. Type-name Range of GlobalQosMapIngressValue cos (0..7) dscp (0..63) exp (0..7)

OBJECT-TYPE

A table of default qos mapping configuration of priority-color to QueueId - thresholdId.

OBJECT-TYPE

Entry of globalQosMapPriColorQidTidDefaultTable.

OBJECT-TYPE

Internal priority.

OBJECT-TYPE

Internal color. Set (1)red, (2)yellow, (3)green.

OBJECT-TYPE

The queue id.

OBJECT-TYPE

The threasholdId id.

OBJECT-TYPE

A table of qos domain cfi config.

OBJECT-TYPE

Entry of globalQosCfiTable.

OBJECT-TYPE

QoS domain to be configured. Range is <0~7>.

OBJECT-TYPE

Cfi enable status of qos domain. Set (1)enable, (2)disable. Default:(2)disable.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

A table of interface shape.

OBJECT-TYPE

Entry of interface shape talbe.

OBJECT-TYPE

Port shape mode type. 1 means port shape is based on percent of interface max bandwidth. 2 means port shape is based on the configured rate.

OBJECT-TYPE

Percent value of interface max bandwidth. Range is <0-99>.

OBJECT-TYPE

Rate of interface max value. Range <0-10000000>kbps.

OBJECT-TYPE

The status of this conceptual row.Now only realize CreateAndGo and Destroy and Active. 1 means Active 4 means CreateAndGo 6 means Destroy

OBJECT-TYPE

A table of interface queue shape.

OBJECT-TYPE

Entry of interface queue shape table.

OBJECT-TYPE

Queue Id of the interface. Range <0-7>

OBJECT-TYPE

Port shape mode type. 1 means queue shape is based on percent of interface max bandwidth. 2 means queue shape is based on the configured rate. If no shape is configured, zero will be got.

OBJECT-TYPE

Percent value of interface max bandwidth. Range is <0-100>. This value influences the commit information rate. This value should not be larger than ifQosShapeQueueCfgPercentPeak. If the queue shape is rate mode, this value is 0.

OBJECT-TYPE

Percent value of interface max bandwidth. Range is <0-100>. This value influences the peak information rate. This value should not be smaller than ifQosShapeQueueCfgPercent. If the queue shape is rate mode, this value is 0.

OBJECT-TYPE

Commit information rate of interface queue shaping. Range <0-10000000>kbps. This value should not be larger than ifQosShapeQueueCfgRatePeak. If the queue shape is percent mode, this value is 0.

OBJECT-TYPE

Peak information rate of interface queue shaping. Range <0-10000000>kbps. This value should not be smaller than ifQosShapeQueueCfgRate. If the queue shape is percent mode, this value is 0.

OBJECT-TYPE

The status of this conceptual row.Now only realize CreateAndGo and Destroy and Active. 1 means Active 4 means CreateAndGo 6 means Destroy

OBJECT-IDENTITY

OBJECT-TYPE

A table of interface queue class and Drr Weight .

OBJECT-TYPE

Interface queue class and Drr Weight entry.

OBJECT-TYPE

Queue Id.Range is <0-7>.

OBJECT-TYPE

<0-6>:Class Id of the selected queue. Set -1 to return it to default value.

OBJECT-TYPE

DRR weight of selected queue. <1-100>: DRR weight range. Set -1 to return it to default value.

OBJECT-TYPE

A table of interface queue management.

OBJECT-TYPE

Entry of ifQosQueueManageCfgTable.

OBJECT-TYPE

Queue Id.Range is <0-7>

OBJECT-TYPE

Queue management mode. (-1) taildrop. (0-10) the value of EWMA factor,default EWMA factor is 9. If this value is (0-10), the drop type is weighted random early drop(wred) mode.

OBJECT-TYPE

Drop threshold for precedence0, only for taildrop mode. 65535 is returned for other mode.Range is <0-12884>. The set of this value will be ignored for non-taildrop mode. Set -1 to delete current configuration and retrieve default configuration. For 1G port, default value is 224; For 10G port, default value is 576

OBJECT-TYPE

Drop threshold for precedence1, only for taildrop mode. 65535 is returned for other mode.Range is <1-12885>. The set of this value will be ignored for non-taildrop mode. Set -1 to delete current configuration and retrieve default configuration. For 1G port, default value is 240; For 10G port, default value is 592.

OBJECT-TYPE

Drop threshold for precedence1, only for taildrop mode. 65535 is returned for other mode. Range is <2-12886>. The set of this value will be ignored for non-taildrop mode. Set -1 to delete current configuration and retrieve default configuration for all precedence. For 1G port, default value is 256; For 10G port, default value is 608.

OBJECT-TYPE

Random-detect drop precedence0 min threshold, only for wred mode. 65535 is returned for other mode. Range is <0-12886>. The set of this value will be ignored for non-wred mode. Set -1 to delete current configuration and retrieve default configuration for all precedence. For 1G port, default value is 16;

OBJECT-TYPE

Random-detect drop precedence1 min threshold, only for wred mode. 65535 is returned for other mode. Range is <0-12886>. The set of this value will be ignored for non-wred mode. Set -1 to delete current configuration and retrieve default configuration for all precedence. For 1G port, default value is 24;

OBJECT-TYPE

Random-detect drop precedence2 min threshold, only for wred mode. 65535 is returned for other mode. Range is <0-12886>.For 1G port, default value is 32; Set -1 to delete current configuration and retrieve default configuration.

OBJECT-TYPE

Random-detect drop precedence0 max threshold, only for wred mode, 65535 is returned for other mode.Range is <1-12887>. The set of this value will be ignored for non-wred mode. Set -1 to delete current configuration and retrieve default configuration for all precedence. For 1G port, default value is 480;

OBJECT-TYPE

Random-detect drop precedence1 max threshold, only for wred mode. The set of this value will be ignored for non-wred mode. 65535 is returned for other mode. Range is <1-12887>. Set -1 to delete current configuration and retrieve default configuration for all precedence. For 1G port, default value is 496;

OBJECT-TYPE

Random-detect drop precedence2 max threshold, only for wred mode. The set of this value will be ignored for non-taildrop mode. 65535 is returned for other mode. Range is <1-12887>. Set -1 to delete current configuration and retrieve default configuration for all precedence. For 1G port, default value is 512;

OBJECT-TYPE

Random-detect drop precedence0 drop probability, only for wred mode. Set -1 to delete current configuration and retrieve default configuration. The default value is 1024. -2 is returned for other mode. Range is <0-65535>.

OBJECT-TYPE

Random-detect drop precedence1 drop probability, only for wred mode. Set -1 to delete current configuration and retrieve default configuration. The default value is 1024. -2 is returned for other mode. Range is <0-65535>.

OBJECT-TYPE

Random-detect drop precedence2 drop probability, only for wred mode. Set -1 to delete current configuration and retrieve default configuration. The default value is 1024. -2 is returned for other mode. Range is <0-65535>.

OBJECT-IDENTITY

OBJECT-TYPE

A table of interface CAR applied.

OBJECT-TYPE

Entry of ifQosCarApplyTable.

OBJECT-TYPE

Direction of this port-policer applied on. (1) input. (2) output.

OBJECT-TYPE

Value 1 for color aware mode policer, value 2 for color blind mode policer.

OBJECT-TYPE

Commit information rate (kbps). Range is <8-10000000>.

OBJECT-TYPE

Commit burst size (bytes). Range is <1000-128000>.

OBJECT-TYPE

Set (1) is select rfc2697 mode. Set (2) is select rfc2698 mode. Set (3) is select rfc4115 mode. Set (4) is select bwp mode.

OBJECT-TYPE

When Type mode is rcf2698 means Peak information rate (kbps). When Type mode is rfc2697&rfc4115&bwp means Excess Information Rate (kbps). Range is <8-10000000>.

OBJECT-TYPE

When Type mode is rcf2698 means Peak burst size (bytes). When Type mode is rfc2697&rfc4115&bwp means Excess Burst Size (bytes). Range is <1000-128000>.

OBJECT-TYPE

Drop color configuration.When configuring 'red(1)', it only drops red packet; configuring 'yellow(2)', it drops both 'red' and 'yellow' packet.

OBJECT-TYPE

2 for using L2 frame length; 1 for using L3 length.

OBJECT-TYPE

The status of this conceptual row.Now only realize CreateAndGo and Destroy and Active. 1 means Active 4 means CreateAndGo 6 means Destroy

OBJECT-IDENTITY

OBJECT-TYPE

A table of interface cos value.

OBJECT-TYPE

Entry of ifQosCosTable.

OBJECT-TYPE

Cos value for this interface.Range is <0-7>. The default CoS for each interface is 0.

OBJECT-TYPE

A table of interface trust type.

OBJECT-TYPE

Entry of ifQosTrustTypeTable.

OBJECT-TYPE

Trust priority type for this interface. Set trust-default to delete current configuration and retrieve default configuration. trustDefault(-1) trustPort(0) trustSTagCos(2) trustDscpExp(3) trustIpPre(4) trustCTagCos(5)

OBJECT-TYPE

A table of interface Domain value.

OBJECT-TYPE

Entry of ifQosDomainTable.

OBJECT-TYPE

Domain value for this interface. Range <0-7>. The default value is 0

OBJECT-IDENTITY

OBJECT-TYPE

A table of ifQosReplaceEntry.

OBJECT-TYPE

Entry of ifQosReplaceTable.

OBJECT-TYPE

Replace priority type for this interface. The defult cos is stagcos; The value of set this node only can be follow: cos(1), cosctag(2), cosstag(3), dscpExp(4), nodscp(7), nocos(8)

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

This object contains an appropriate value to be used for cbQoSClassifierIndex when creating rows in the cbQoSClassifierCfgInfoTable. If the value of this node is less than 0, it indicates creating a Rowin cbQoSClassifierCfgInfoTable is not permitted.

OBJECT-TYPE

A table of Classifier configuration information.

OBJECT-TYPE

Classifier Configuration Information Entry.

OBJECT-TYPE

Index of this class-map.Range is <10000-20000>.

OBJECT-TYPE

Name of class-map. Only used in creating a conceptual row, can not modified in an 'active' Row

OBJECT-TYPE

The counter of match rules in class-map.

OBJECT-TYPE

Operator of the match rules of class-map. Default match operator is match-any. 'and(1)' for match-all rules. 'or(2)' for match-any rules.

OBJECT-TYPE

This object contains an appropriate value to be used for cbQoSMatchRuleIndex when creating rows in the cbQoSMatchRuleCfgInfoTable.Begin with 0. If the value of this node is less than 0, it indicates creating a Rowin cbQoSMatchRuleCfgInfoTable is not permitted.

OBJECT-TYPE

The status of this conceptual row.Now only realize CreateAndGo and Destroy and Active. 1 means Active 4 means CreateAndGo 6 means Destroy

OBJECT-TYPE

A table of match rule configuration in class-map.

OBJECT-TYPE

Match Rule Entry in Class-map.

OBJECT-TYPE

Index of Match Rule. Currently only access-group(ACL) is used as matching rule. Range is <10000-20000>.

OBJECT-TYPE

Match ACl name.Only used in creating a conceptual row, can not modified in an 'active' Row

OBJECT-TYPE

The status of this conceptual row.Now only realize CreateAndGo and Destroy and Active. 1 means Active 4 means CreateAndGo 6 means Destroy

OBJECT-IDENTITY

OBJECT-TYPE

This object contains an appropriate value to be used for cbQoSPolicyIndex when creating rows in the cbQoSPolicyCfgInfoTable.

OBJECT-TYPE

A table of policy-map.

OBJECT-TYPE

Policy-map table Entry.

OBJECT-TYPE

Index of this policy-map.Range is <10000-20000>.

OBJECT-TYPE

Name of this policy-map. Only used in creating a conceptual row, can not modified in an 'active' Row

OBJECT-TYPE

The counter of class-maps in this policy-map.

OBJECT-TYPE

This object contains an appropriate value to be used for cbQoSPolicyClassIndex when creating rows in the cbQoSPolicyClassCfgInfoTable. If the returned value is less 0, it indicates creating a Rowis not permitted.

OBJECT-TYPE

The status of this conceptual row.Now only realize CreateAndGo and Destroy and Active. 1 means Active 4 means CreateAndGo 6 means Destroy

OBJECT-TYPE

A table of policy-class.

OBJECT-TYPE

Policy-class table Entry.

OBJECT-TYPE

Index of this policy-class.Range is <10000-20000>.

OBJECT-TYPE

Index of classifier applied by a policy. It is corresponding to cbQoSClassifierName. The maximum index value 20000 is reserved for class-map class-default only.

OBJECT-TYPE

Name of classifier applied by a policy. It should exist in cbQoSClassifierCfgInfoTable. Only used in creating a conceptual row, can not modified in an 'active' row.

OBJECT-TYPE

The status of this conceptual row.Now only realize CreateAndGo and Destroy and Active. 1 means Active 4 means CreateAndGo 6 means Destroy

OBJECT-IDENTITY

OBJECT-TYPE

This object contains an appropriate value to be used for cbQoSAggregativeCarIndex when creating rows in the cbQoSAggregativeCarCfgInfoTable.

OBJECT-TYPE

A table of aggregate-policer.

OBJECT-TYPE

Aggregate-policer table Entry.

OBJECT-TYPE

Index of aggregate-policer.Range is <10000-20000>.

OBJECT-TYPE

Name of aggregate-policer.Only used in creating a conceptual row, can not modified in an 'active' row.

OBJECT-TYPE

Value 1 for color aware mode policer; value 2 for color blind mode policer. Can modified in an 'active' row.

OBJECT-TYPE

Commit information rate (kbps).Range is <8-10000000>. Only used in creating a conceptual row, can not modified in an 'active' row.

OBJECT-TYPE

Commit burst size (bytes).Range is <1000-128000>. Only used in creating a conceptual row, can not modified in an 'active' row.

OBJECT-TYPE

Set (1) is select TRTCM mode. Set (2) is select SRTCM mode.

OBJECT-TYPE

Excess burst size (bytes).Range is <1000-128000>. Only used in creating a conceptual row, can not modified in an 'active' row. If the cbQoSAggregativeCarPir is not zero, this value will be ignored.

OBJECT-TYPE

Peak information rate (kbps).Range is <8-10000000>. Only used in creating a conceptual row, can not modified in an 'active' row. This valude should not be less than cbQoSAggregativeCarCir.

OBJECT-TYPE

Peak burst size (bytes).Range is <1000-128000>. Only used in creating a conceptual row, can not modified in an 'active' row. If the cbQoSAggregativeCarPir is zero, this value will be ignored; This valude should not be less than cbQoSAggregativeCarCbs.

OBJECT-TYPE

Drop color configuration.When configuring 'red', it only drops red packet; configuring 'yellow', it drops both 'red' and 'yellow' packet. Only used in creating a conceptual row, can not modified in an 'active' row.

OBJECT-TYPE

2 for using L2 frame length; 1 for using L3 length. Only used in creating a conceptual row, can not modified in an 'active' row.

OBJECT-TYPE

2 policer stats is disable; 1 policer stats is enable. Only used in creating a conceptual row, can not modified in an 'active' row.

OBJECT-TYPE

The status of this conceptual row.Now only realize CreateAndGo and Destroy and Active. 1 means Active 4 means CreateAndGo 6 means Destroy

OBJECT-TYPE

A table of behavior.

OBJECT-TYPE

Behavior table Entry.

OBJECT-TYPE

Index of Policy-map. Range is <10000-20000>. Associated with cbQoSPolicyIndex of cbQoSPolicyCfgInfoEntry.

OBJECT-TYPE

Index of Policy class-map. Range is <10000-20000>. Associated with cbQoSPolicyClassIndex of cbQoSPolicyClassCfgInfoEntry.

OBJECT-TYPE

Value 1 for color aware mode policer, value 2 for color blind mode policer. Only for policer behavior.

OBJECT-TYPE

Commit information rate (kbps).Range is <8-10000000>. Only for policer behavior.

OBJECT-TYPE

Commit burst size (bytes).Range is <1000-128000>. Only for policer behavior.

OBJECT-TYPE

Set (1) is select rfc2697 mode. Set (2) is select rfc2698 mode. Set (3) is select rfc4115 mode. Set (4) is select bwp mode.

OBJECT-TYPE

Excess burst size (bytes).Range is <1000-128000>. Only for policer behavior.

OBJECT-TYPE

Peak information rate (kbps).Range is <8-10000000>. Only for policer behavior.

OBJECT-TYPE

Peak burst size (bytes).Range is <1000-128000>. Only for policer behavior.

OBJECT-TYPE

Drop color configuration.Only 'red' and 'yellow' can be used here. When configuring 'red(1)', it only drops red packet; configuring 'yellow(2)', it drops both 'red' and 'yellow' packet. Only for policer behavior. When policy mode is aggregative policer, the result of DropColor will be none(0).

OBJECT-TYPE

2 for using L2 frame length; 1 for using L3 length. Only for policer behavior.

OBJECT-TYPE

2 policer stats is disable; 1 policer stats is enable. Only for policer behavior.

OBJECT-TYPE

The status of this conceptual row.Now only realize CreateAndGo and Destroy and Active. 1 means Active 4 means CreateAndGo 6 means Destroy

OBJECT-TYPE

A table of setting priority-color behavior.

OBJECT-TYPE

Setting priority-color table Entry.

OBJECT-TYPE

Index of Policy-map. Associated with cbQoSPolicyIndex of cbQoSPolicyCfgInfoEntry.

OBJECT-TYPE

Index of Policy class-map.Range is <10000-20000>. Associated with cbQoSPolicyClassIndex of cbQoSPolicyClassCfgInfoEntry.

OBJECT-TYPE

Internal priority value.Range id <0-63>. Default priority is 0.

OBJECT-TYPE

Internal color. Set (1)red, (2)yellow, (3)green. Set (0) means no set priority.

OBJECT-TYPE

A table of behavior.

OBJECT-TYPE

ClassTrafficOption table Entry.

OBJECT-TYPE

Index of Policy-map.Range is <10000-20000>. Associated with cbQoSPolicyIndex of cbQoSPolicyCfgInfoEntry.

OBJECT-TYPE

Index of Policy class-map.Range is <10000-20000>. Associated with cbQoSPolicyClassIndex of cbQoSPolicyClassCfgInfoEntry.

OBJECT-TYPE

Use which prioritization type for this flow. trustNone(-1) trustPort(0) trustCos(2) trustDscp(3) trustIpPre(4) trustCosCtag(5) trustCosStag(6)

OBJECT-TYPE

1 for enable statistics for each ace in class map; 2 for disable statistics for each ace in class map. Default value is 2.

OBJECT-TYPE

<1-65535>:Interface index of redirect. Set 0 means no redirect.

OBJECT-TYPE

<1-3> monitor session number; 0 no monitor, default value is 0.

OBJECT-TYPE

A table of behavior.

OBJECT-TYPE

Behavior table Entry.

OBJECT-TYPE

Index of Policy-map. Range is <10000-20000>. Associated with cbQoSPolicyIndex of cbQoSPolicyCfgInfoEntry.

OBJECT-TYPE

Index of Policy class-map. Range is <10000-20000>. Associated with cbQoSPolicyClassIndex of cbQoSPolicyClassCfgInfoEntry.

OBJECT-TYPE

Only for aggregative policer name.

OBJECT-TYPE

The status of this conceptual row.Now only realize CreateAndGo and Destroy and Active. 1 means Active 4 means CreateAndGo 6 means Destroy

OBJECT-IDENTITY

OBJECT-TYPE

A table of policy applied on interface.

OBJECT-TYPE

Policy-applied table Entry.

OBJECT-TYPE

Ifindex. The interface should only be physical, vlan, or linkagg interface.

OBJECT-TYPE

Direction of this service-policy applied on. 1. input direction. 2. output direction.

OBJECT-TYPE

Index of policy in cbQoSPolicyCfgInfoTable. It is corresponding to cbQoSIfApplyPolicyName.

OBJECT-TYPE

Name of policy applied. It should exist in cbQoSPolicyCfgInfoTable. Only used in creating a conceptual row, can not modified in an 'active' Row

OBJECT-TYPE

The status of this conceptual row.Now only realize CreateAndGo and Destroy and Active. 1 means Active 4 means CreateAndGo 6 means Destroy

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

Table of qos sap ingress.

OBJECT-TYPE

Entries of qos sap ingress.

OBJECT-TYPE

Name of the qos sap ingress.

OBJECT-TYPE

Status of the srvQosSapIngressEntry row. 1 means Active 4 means CreateAndGo 6 means Destroy.

OBJECT-TYPE

Descrption of the qos sap ingress.

OBJECT-TYPE

Policy map for the qos sap ingress.

OBJECT-TYPE

Table of qos sap ingress policer.

OBJECT-TYPE

Entries of qos sap ingress policer.

OBJECT-TYPE

Policer mode of the qos sap ingress.

OBJECT-TYPE

Cir of the qos sap ingress.

OBJECT-TYPE

Cbs of the qos sap ingress.

OBJECT-TYPE

Ebs of the qos sap ingress.

OBJECT-TYPE

Pir of the qos sap ingress.

OBJECT-TYPE

Pbs of the qos sap ingress.

OBJECT-TYPE

Drop color of the qos sap ingress.

OBJECT-TYPE

If L3 length is used for the qos sap ingress.

OBJECT-IDENTITY

OBJECT-TYPE

Table of qos sap Egress.

OBJECT-TYPE

Entries of qos sap Egress.

OBJECT-TYPE

Name of the qos sap Egress.

OBJECT-TYPE

Status of the srvQosSapEgressEntry row. 1 means Active 4 means CreateAndGo 6 means Destroy.

OBJECT-TYPE

Descrption of the qos sap Egress.

OBJECT-TYPE

Total Rate of the qos sap Egress.

OBJECT-TYPE

Table of qos sap egress queue.

OBJECT-TYPE

Entries of qos sap egress queue.

OBJECT-TYPE

Id of the qos sap Egress Queue.

OBJECT-TYPE

Shape rate for commit information rate, kbps.

OBJECT-TYPE

Shape rate for peak information rate, kbps.

OBJECT-TYPE

Table of qos sap egress queue info.

OBJECT-TYPE

Entries of qos sap egress queue info.

OBJECT-TYPE

-1: Tail Drop 0-10: WRED Exponential-Weighted-Moving-Average (EWMA) factor.

OBJECT-TYPE

Tail drop threshold0.

OBJECT-TYPE

Tail drop threshold1, should greater than threshold0.

OBJECT-TYPE

Tail drop threshold2, should greater than threshold1.

OBJECT-TYPE

Tail drop threshold3, should greater than threshold2.

OBJECT-TYPE

Random-detect threshold0's min threshold range.

OBJECT-TYPE

Random-detect threshold1's min threshold range.

OBJECT-TYPE

Random-detect threshold2's min threshold range.

OBJECT-TYPE

Random-detect threshold3's min threshold range.

OBJECT-TYPE

Random-detect threshold0's max threshold range.

OBJECT-TYPE

Random-detect threshold1's max threshold range.

OBJECT-TYPE

Random-detect threshold2's max threshold range.

OBJECT-TYPE

Random-detect threshold3's max threshold range.

OBJECT-TYPE

Random-detect threshold0 drop probability range.

OBJECT-TYPE

Random-detect threshold1 drop probability range.

OBJECT-TYPE

Random-detect threshold2 drop probability range.

OBJECT-TYPE

Random-detect threshold3 drop probability range.

OBJECT-IDENTITY

OBJECT-TYPE

Number of queues allocated by each service.

OBJECT-TYPE

The maximum support queue number.

OBJECT-TYPE

The allocated queue number.

OBJECT-TYPE

The maximum support service number.

OBJECT-TYPE

The allocated service number.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

The status of policer statistics. (1) enable. (2) disable.

OBJECT-TYPE

The status of queue statistics. (1) enable. (2) disable.

OBJECT-IDENTITY

OBJECT-TYPE

A table of clearing Stats for Policy in a QoS policy applied on the interface.

OBJECT-TYPE

Clear Stats information entry.

OBJECT-TYPE

Policy map entry index. Range 10000~20000.

OBJECT-TYPE

Reset the value of the policer statistics in policy-map.Clear(0).

OBJECT-TYPE

Reset the value of the ace-matching statistics in policy-map.Clear(0).

OBJECT-TYPE

A table of clearing Stats for Policy in a QoS PortPolicy applied on the interface.

OBJECT-TYPE

Clear Stats information entry.

OBJECT-TYPE

Interface Index, equal to ifIndex.

OBJECT-TYPE

Policy direction: inbound (1) outbound (2)

OBJECT-TYPE

Reset the statistics of port policer.Clear(0).

OBJECT-TYPE

A table of clearing Stats for Policy in a QoS AggPolicy applied on the interface.

OBJECT-TYPE

Clear agg policer stats information entry.

OBJECT-TYPE

Index of aggregate-policer.

OBJECT-TYPE

Reset the value of the Stats.Clear(0).

OBJECT-TYPE

A table of clearing Stats for Policy in a QoS Queue applied on the interface.

OBJECT-TYPE

Clear Stats information entry.

OBJECT-TYPE

Interface Index, equal to ifIndex.

OBJECT-TYPE

Interface queue id.

OBJECT-TYPE

Reset the value of the Stats.Clear(0).

OBJECT-IDENTITY

OBJECT-TYPE

A table of Running Stats for Policy in a QoS policy applied on the interface.

OBJECT-TYPE

Policy Stats information entry.

OBJECT-TYPE

Interface Index, equal to ifIndex.

OBJECT-TYPE

Policy direction: inbound (1) outbound (2)

OBJECT-TYPE

PolicyClass Index in a QoS policy.

OBJECT-TYPE

Number of green packets.

OBJECT-TYPE

Number of green bytes.

OBJECT-TYPE

Number of red packets.

OBJECT-TYPE

Number of red bytes.

OBJECT-TYPE

Number of yellow packets.

OBJECT-TYPE

Number of yellow bytes.

OBJECT-TYPE

Number of policy class matching packets.

OBJECT-TYPE

Number of policy class matching bytes.

OBJECT-TYPE

A table of Running Stats in a QoS policy applied on the port.

OBJECT-TYPE

Policy Stats information entry.

OBJECT-TYPE

Interface Index, equal to ifIndex.

OBJECT-TYPE

Policy direction: inbound (1) outbound (2)

OBJECT-TYPE

Number of green packets.

OBJECT-TYPE

Number of green bytes.

OBJECT-TYPE

Number of red packets.

OBJECT-TYPE

Number of red bytes.

OBJECT-TYPE

A table of Running Stats for queue in a QoS policy applied on the interface.

OBJECT-TYPE

Queue Stats entry.

OBJECT-TYPE

Interface Index, equal to ifIndex.

OBJECT-TYPE

Queue ID. Range <0-7>.

OBJECT-TYPE

Number of packets enqueued.

OBJECT-TYPE

Number of bytes enqueued.

OBJECT-TYPE

Number of packets discarded when enqueued by tail-drop/wred method. It's zero if the system does not support queue drop statistics.

OBJECT-TYPE

Number of bytes discarded when enqueued by tail-drop/wred method. It's zero if the system does not support queue drop statistics.

OBJECT-TYPE

A table of Running Stats for matching QoS policy Ace applied on the interface. The matching ace statistics is only for match-any class-map in policy-map

OBJECT-TYPE

Policy Stats information entry.

OBJECT-TYPE

Interface Index, equal to ifIndex.

OBJECT-TYPE

Policy direction: inbound (1) outbound (2)

OBJECT-TYPE

PolicyClass index in policy-map.

OBJECT-TYPE

Match rule index in Class-map.

OBJECT-TYPE

Rule index(sequence num in cli) in acl Group.

OBJECT-TYPE

Number of packets matching ace in policy-map.

OBJECT-TYPE

Bytes of packets matching ace in policy-map.

OBJECT-TYPE

A table of Running Stats in a QoS aggregate policy applied on the interface.

OBJECT-TYPE

Aggregate Policy Stats information entry.

OBJECT-TYPE

Index of aggregate-policer.

OBJECT-TYPE

Number of red packets.

OBJECT-TYPE

Number of red bytes.

OBJECT-TYPE

Number of green packets.

OBJECT-TYPE

Number of green bytes.

OBJECT-TYPE

Number of yellow packets.

OBJECT-TYPE

Number of yellow bytes.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

Configure to enable IGMP Snooping. enable(1) disable(2)

OBJECT-TYPE

Configure to enable IGMP Snooping Fast Leave. enable(1) disable(2)

OBJECT-TYPE

Configure to set IGMP Snooping Version.

OBJECT-TYPE

Configure the max member number.

OBJECT-TYPE

Configure to enable IGMP Snooping Discard unknown multicast traffic. enable(1) disable(2)

OBJECT-TYPE

Configure to enable IGMP Snooping Report-Suppression. enable(1) disable(2)

OBJECT-TYPE

Configure to set IGMP Snooping Last Member Query Interval. Interval range 1000~25500.

OBJECT-TYPE

Configure to set IGMP Snooping Query Interval.Must more than query max response time. Interval range 2~18000.

OBJECT-TYPE

Configure to set IGMP Snooping Query Max Response Time.Time range 1~25.

OBJECT-TYPE

The table contains, one entry per vlan, infomation about the IGMP Snooping.

OBJECT-TYPE

Entry containing information about the IGMP Snooping on vlan.

OBJECT-TYPE

An index uniquely identifies the VLAN id which IGMP snooping is enabled or disabled.

OBJECT-TYPE

Indicating whether IGMP snooping is enabled on this VLAN. enable(1) disable(2)

OBJECT-TYPE

Configure to enable IGMP Snooping Fast Leave on VLAN, enable(1) disable(2).

OBJECT-TYPE

Configure to enable IGMP Snooping Report-Suppression on VLAN. enable(1) disable(2)

OBJECT-TYPE

Configure to set IGMP Snooping Version on VLAN.Version range 1~3.

OBJECT-TYPE

Configure the max member number on VLAN.Range 1~8192.

OBJECT-TYPE

Configure to enable IGMP Snooping Discard unknown multicast traffic on VLAN. enable(1) disable(2)

OBJECT-TYPE

Configure the IGMP Snooping Group Acess-list on VLAN.

OBJECT-TYPE

Configure to set IGMP Snooping Last Member Query Interval on VLAN. Interval range 1000~25500.

OBJECT-TYPE

Configure to Enable or Disable IGMP Snooping Querier on VLAN. enable(1) disable(2)

OBJECT-TYPE

Configure to get IGMP Snooping Querier Operational Adress on VLAN.

OBJECT-TYPE

Configure to set IGMP Snooping Querier Configure Adress on VLAN.

OBJECT-TYPE

Configure to set IGMP Snooping Querier Timeout value on VLAN. Timeout range 60~300.

OBJECT-TYPE

Configure to set IGMP Snooping Query Interval on VLAN. Query interval should be greater than Query Response Interval. Interval range 2~18000.

OBJECT-TYPE

Configure to set IGMP Snooping Query Max Response Time on VLAN.

OBJECT-TYPE

Configure to get IGMP Snooping Group Joins Count on VLAN.

OBJECT-TYPE

Configure to get IGMP Snooping Group Leaves Count on VLAN.

OBJECT-TYPE

Configure to get IGMP Snooping Group V1-Querier Warnings Count on VLAN.

OBJECT-TYPE

Configure to get IGMP Snooping Group V2-Querier Warnings Count on VLAN.

OBJECT-TYPE

Configure to reset IGMP SnoopingStatus Counters on VLAN. 1 reset.

OBJECT-TYPE

Configure to get IGMP Snooping group number on VLAN.

OBJECT-TYPE

Configure to get IGMP Snooping Elected Querier Adress on VLAN.

OBJECT-TYPE

A table that contains information about igmp snooping mrouter port list per vlan.

OBJECT-TYPE

Information about IGMP Snooping Mrouter Port on VLAN.

OBJECT-TYPE

The VLAN identifier of this mrouter port.

OBJECT-TYPE

mrouter port ifindex . 1~1024 is switch port, 1025~1151 is agg port(agg1~127).