MIBs Depot

SOFTWIRE-MESH-MIB

Registered at
1.3.6.1.2.1.239
Last updated
2016-05-11 00:00
Organization
Softwire Working Group
Revisions
2016-05-11 00:00
Namespace
standard
Source file
SOFTWIRE-MESH-MIB
Digest
sha256:78a9b36fd273ab3ae80dbabad8867937bdfbcf0d6b73b8b593e9b72cd15d4bd4

Description

This MIB module contains managed object definitions for the softwire mesh framework. Copyright (c) 2016 IETF Trust and the persons identified as authors of the code. All rights reserved. Redistribution and use in source and binary forms, with or without modification, is permitted pursuant to, and subject to the license terms contained in, the Simplified BSD License set forth in Section 4.c of the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info).

Contact

Yong Cui Email: yong@csnet1.cs.tsinghua.edu.cn Jiang Dong Email: knight.dongjiang@gmail.com Peng Wu Email: weapon9@gmail.com Mingwei Xu Email: xmw@cernet.edu.cn Antti Yla-Jaaski Email: antti.yla-jaaski@aalto.fi Email comments directly to the Softwire WG Mailing List at softwires@ietf.org

Imports

FromSymbols
IANAifType-MIBIANAtunnelType
IF-MIBifIndex
INET-ADDRESS-MIBInetAddress, InetAddressPrefixLength, InetAddressType
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP
SNMPv2-SMIMODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, iso, mib-2
SNMPv2-TCDisplayString, TEXTUAL-CONVENTION

Imported by

Nothing in this corpus imports this module.

Load order

Every file a consumer needs in order to load this module, dependencies first.

IANAifType-MIB
IF-MIB
INET-ADDRESS-MIB
SNMPv2-CONF
SNMPv2-MIB
SNMPv2-SMI
SNMPv2-TC
SOFTWIRE-MESH-MIB

Objects

NameOIDSyntaxAccessStatus
swmObjects
OBJECT-IDENTITY
1.3.6.1.2.1.239.1
swmSupportedTunnelTable
OBJECT-TYPE
A table of objects that show what kinds of tunnels can be supported by the AFBR.
1.3.6.1.2.1.239.1.1not-accessiblecurrent
swmSupportedTunnelEntry
OBJECT-TYPE
A set of objects that show what kinds of tunnels can be supported in the AFBR. If the AFBR supports multiple tunnel types, the swmSupportedTunnelTable would have several entries.
1.3.6.1.2.1.239.1.1.1not-accessiblecurrent
swmSupportedTunnelType
OBJECT-TYPE
Represents the tunnel type that can be used for softwire mesh scenarios, such as L2TPv3 over IP, GRE, Transmit tunnel endpoint, IPsec in Tunnel-mode, IP in IP tunnel with IPsec Transport Mode, MPLS-in-IP tunnel with IPsec Transport Mode, and IP in IP. There is no restriction on the tunnel type the softwire mesh can use.
1.3.6.1.2.1.239.1.1.1.1IANAtunnelTyperead-onlycurrent
swmEncapsTable
OBJECT-TYPE
A table of objects that display the softwire mesh encapsulation information.
1.3.6.1.2.1.239.1.2not-accessiblecurrent
swmEncapsEntry
OBJECT-TYPE
A table of objects that manage the softwire mesh I-IP encapsulation destination based on the E-IP destination prefix.
1.3.6.1.2.1.239.1.2.1not-accessiblecurrent
swmEncapsEIPDstType
OBJECT-TYPE
This object specifies the address type used for swmEncapsEIPDst. It is different from the tunnelIfAddressType in the tunnelIfTable. The swmEncapsEIPDstType is IPv6 (2) if it is IPv6-over-IPv4 tunneling. The swmEncapsEIPDstType is IPv4 (1) if it is IPv4-over-IPv6 tunneling.
1.3.6.1.2.1.239.1.2.1.1InetAddressTypenot-accessiblecurrent
swmEncapsEIPDst
OBJECT-TYPE
The E-IP destination prefix, which is used for I-IP encapsulation destination looking up. The type of this address is determined by the value of swmEncapsEIPDstType
1.3.6.1.2.1.239.1.2.1.2InetAddressnot-accessiblecurrent
swmEncapsEIPPrefixLength
OBJECT-TYPE
The prefix length of the E-IP destination prefix.
1.3.6.1.2.1.239.1.2.1.3InetAddressPrefixLengthnot-accessiblecurrent
swmEncapsIIPDstType
OBJECT-TYPE
This object specifies the address type used for swmEncapsIIPDst. It is the same as the tunnelIfAddressType in the tunnelIfTable.
1.3.6.1.2.1.239.1.2.1.4InetAddressTyperead-onlycurrent
swmEncapsIIPDst
OBJECT-TYPE
The I-IP destination address, which is used as the encapsulation destination for the corresponding E-IP prefix. Since the tunnelIfRemoteInetAddress in the tunnelIfTable should be 0.0.0.0 or ::, swmEncapIIPDst should be the destination address used in the outer IP header.
1.3.6.1.2.1.239.1.2.1.5InetAddressread-onlycurrent
swmBGPNeighborTable
OBJECT-TYPE
A table of objects that display the softwire mesh BGP neighbor information.
1.3.6.1.2.1.239.1.3not-accessiblecurrent
swmBGPNeighborEntry
OBJECT-TYPE
A set of objects that display the softwire mesh BGP neighbor information.
1.3.6.1.2.1.239.1.3.1not-accessiblecurrent
swmBGPNeighborInetAddressType
OBJECT-TYPE
This object specifies the address type used for swmBGPNeighborInetAddress.
1.3.6.1.2.1.239.1.3.1.1InetAddressTypenot-accessiblecurrent
swmBGPNeighborInetAddress
OBJECT-TYPE
The address of the AFBR's BGP neighbor. The address type is the same as the tunnelIfAddressType in the tunnelIfTable.
1.3.6.1.2.1.239.1.3.1.2InetAddressnot-accessiblecurrent
swmBGPNeighborTunnelType
OBJECT-TYPE
Represents the type of tunnel that the AFBR chooses to transmit traffic with another AFBR/BGP neighbor.
1.3.6.1.2.1.239.1.3.1.3IANAtunnelTyperead-onlycurrent
swmConformance
OBJECT-IDENTITY
1.3.6.1.2.1.239.2
swmCompliances
OBJECT-IDENTITY
1.3.6.1.2.1.239.2.1
swmGroups
OBJECT-IDENTITY
1.3.6.1.2.1.239.2.2

Conformance

NameOIDStatus
swmCompliance
MODULE-COMPLIANCE
Describes the requirements for conformance to the Softwire Mesh MIB. The following index objects cannot be added as OBJECT clauses but nevertheless have compliance requirements:
1.3.6.1.2.1.239.2.1.1current
swmSupportedTunnelGroup
OBJECT-GROUP
The collection of objects that are used to show what kind of tunnel the AFBR supports.
1.3.6.1.2.1.239.2.2.1current
swmEncapsGroup
OBJECT-GROUP
The collection of objects that are used to display softwire mesh encapsulation information.
1.3.6.1.2.1.239.2.2.2current
swmBGPNeighborGroup
OBJECT-GROUP
The collection of objects that are used to display softwire mesh BGP neighbor information.
1.3.6.1.2.1.239.2.2.3current